REQUIRED TOOLS
AND MATERIALS:
Portable System
Owners Manual
• 2 People
• Tape Measure
• Wood Board (scrap)
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
• Sawhorse or Support
Table
• Hammer
• Tape
• Safety Glasses
• Phillips Screwdriver
• Scissors
• (2 each) Wrenches and/or
Socket Wrenches and Sockets
(Deep-Well Sockets are
Recommended).
3/8"
1/2" 9/16" 3/4"
AND/OR
3/8"
1/2" 9/16" 3/4"
• Extension is Recommended.
• Garden Hose or Sand
Write Model Number
WARNING!
From Box Here:
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO
• Step Ladder - 8 ft. (2.4 m)
PROPERTY.
OPTIONAL TOOLS
AND MATERIALS:
Toll-Free Customer Service Number for U.S: 1-800-558-5234,
For Canada: 1-800-284-8339,
• Large & Small Adjustable
Wrenches
For Europe: 00 800 555 85234 (Sweden: 009 555 85234),
For Australia: 1-800-632 7921
Internet Address: http://www.huffysports.com
1
08/05
P/N M601111
© COPYRIGHT 2005 by SPALDING
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY,
PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully. Proper
and complete assembly, use and supervision is essential for proper operation and to reduce the risk of
accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and
operated properly.
•
•
If using a ladder during assembly, use extreme caution.
Check base regularly for leakage. Slow leaks could cause the system to tip over
unexpectedly
•
Seat the pole sections properly (if applicable). Failure to do so could allow the pole
sections to separate during play and/or during transport of the system.
Climate, corrosion or misuse could result in system failure.
If technical assistance is required, contact Huffy Sports.
Minimum operational height is 6’6” (1.98m) to the bottom of backboard.
•
•
•
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this unit.
HEIGHT ADJUSTMENT
TO ADJUST BACKBOARD:
1
42
3
1. While holding handle, remove pin.
2. Move elevator up or down to
desired height.
2
3. Replace pin full length to lock
system at desired height.
2
MOVING SYSTEM
1.
Adjust basketball backboard
height to lowest position.
1
2. While holding pole, rotate
basketball system forward
until wheels engage with
ground.
3.
4.
5.
Move basketball system to
desired location.
2
Carefully rotate basketball
system upright.
3
4
Checksystem for stability.
511679
05/05
3
08/05
P/N M601111
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTICE TO ASSEMBLERS
ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled
and ballasted with sand or water according to the instructions. Failure to follow instructions
could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system.
IMPORTANT!
Remove all contents from boxes.
Be sure to check inside pole sections;
hardware and additional parts are packed inside.
WARRANTY CARD:
Please remember to complete your product
registration form either on-line at:
www.huffysports.com or mail-in the
enclosed postcard.
WARNING: IF YOUR SYSTEM IS EQUIPPED WITH AN ACRYLIC BACKBOARD,
EXAMINE BACKBOARD FOR ANY DAMAGE THAT MAY HAVE OCCURRED
DURING SHIPMENT. CRACKS IN THE BACKBOARD COULD RESULT IN
SUDDEN BREAKAGE. IF BACKBOARD IS DAMAGED IN ANY WAY PRIOR TO OR
AFTER ASSEMBLY, CALL TOLL-FREE NUMBER:
For more information on assembly, placement, proper
use, and maintenance, visit The American Basketball
4
P/N M601111 08/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Get to know the basic parts of your basketball system...
FRONT
BACK
RIM
BACKBOARD
TOP POLE
ELEVATOR
ASSEMBLY
BOTTOM
POLE
MIDDLE
POLE
FRONT
COVER
STRUTS
BASE
WHEEL
CARRIAGE
ASSEMBLY
5
08/05
P/N M601111
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST - See Hardware Identifier
Item Qty. Part No. Description
Item Qty. Part No. Description
1
2
3
4
5
6
7
8
9
1
1
1
1
1
2
2
1
6
908026 Top Pole Section
90810701 Middle Pole Section (with Label
908015 Bottom Pole Section
900223 Wheel Bracket
206940 Axle
226403 Wheel
206938 Pushnut
206660 Base
203156 Hex Bolt, 5/16-18 x 1
36
37
2
2
204838 Spring, Counter Balance
203617 Base Plug
201965 Front Cover
203257 Tie Straps
200504 Rim Cover
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
68
1
4*
1
2
1
2
1
1
6*
6*
1
1
4
1
2
4
2
1
4
6
1
1
1
1
1
1
1
1
1
200520 Screw, #8 x .75
511679 Label, Height Adj and Moving
204857 Spacer, Metal 1/2” O.D. x 1.44 Long
205226 Left Board Pad
205225 Right Board Pad
201596 Sheet Metal Screw, #14 x 1.25
206303 Flat Washer, 1/4
205241 Center Board Pad
202856 Bolt, Hex, 1/2-13 x 4" Long
203232 Flat Washer, 3/8
10 18* 203218 Flat Washer, 5/16
11 15* 203100 Hex-Flange Nut, 5/16-18
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
1
2
2
4
2
1
1
3
8
7
2
1
2
1
1
1
1
4
6
4
2
2
2
2
201581 Pole Bracket
202662 Hex Bolt, 5/16-18 x 4.5
203099 Lock Nut, 5/16-18
203223 Carriage Bolt, 5/16-18 x 1
906410 Tank Strut
200516 Bolt Cover
206990 Reinforcement Bracket
203038 Carriage Bolt, 5/16-18 x 2-3/4 Long
202862 Spacer, Plastic, 1.19" Long
206340 Lock Nut, 1/2-13
203053 Carriage Bolt, 5/16-18 x 4 Long
204872 Label, Height Indicator
204858 Spacer, Plastic, Biscuit
207103 Pole Cap
204853 Lanyard, Black Coil
204850 Pin, Locking
204832 Bracket, Pole Mount
206360 Hex Bolt, 3/8-16 x 2.625
203063 Nylon Insert Lock Nut, 3/8-16
201124 Lock Nut, 3/8-16
202795 Label, NBA
90096401 Bracket, Backboard Support
201681 Spacer, Plastic, .530 I.D. x .88 Long
203103 Carriage Bolt, 5/16-18 x 2 Long
204803 Screw, Phillips Head
201682 Spacer, .530 I.D. x 1.875
202532 Bolt, Hex, 1/2-13 x 9.5"
904866 Height Adjustment Rod
204855 Handle, Left
204856 Handle, Right
900033 Bracket, Slam Jam
200318 Bracket, Reinforcement, Slam Jam
203470 Washer Flat, Slam Jam
203472 Spring, Black, Slam Jam
203795 Nut, Special, Slam Jam
203796 T-Bolt, 3/8-16 x 5 Long
Rim
900867 Plate, Triangle
904807 Elevator Tube, Upper - Short
900183 Elevator Tube, Lower - Long
204859 Cover, Pin Slide
4
1
205528 Bolt, Hex Flange, 5/16-18 x 1 Long
Net
*You may have extra parts with this model.
HARDWARE IDENTIFIER (NUTS, WASHERS & METAL SPACERS)
Item #30 (4)
Item #14 (2)
Item #11 (15)*
Item #31 (4)
Item #21 (7)
Item #43 (2)
Item #47 (6)*
Item #50 (4)
Item #10 (18)*
6
P/N M601111 08/05
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER (BOLTS & SCREWS)
Item #13 (2)
Item #9 (6)
Item #49 (1)
Item #15 (4)
Item #29 (4)
Item #54 (2)
Item #55 (1)
Item #19 (1)
Item #46 (6)
Item #41 (2)
Item #57 (6)
Item #22 (2)
HARDWARE IDENTIFIER (PLASTIC SPACERS & CAPS)
Item #53 (4)
Item #17 (1)
Item #7 (2)
Item #20 (8)
Item #56 (4)
Item #24 (2)
7
08/05
P/N M601111
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER (RIM)
Item #61 (1)
Item #62 (1)
Item #63 (1)
Item #64 (1)
Item #66 (1)
Item #65 (1)
SECTION A: ASSEMBLE THE POLES
TOOLS REQUIRED FOR THIS SECTION
Wood Board (scrap)
8
P/N M601111 08/05
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
Correctly identify each pole section.
1
I.D. Label
I.D. Label
2
3
WARNING
LABEL
Bounce middle pole (2) into top pole section (1) using a wood scrap as shown until top
pole no longer moves toward pole identification mark on middle pole.
2.
CAUTION!
NOTE:
POLE SECTIONS
SHOULD HAVE A
3-1/2" (9 CM)
MINIMUM
THE IDENTIFICATION STICKER IS
LOCATED 5" FROM THE END OF THE
POLE. WHEN PROPERLY POUNDED
TOGETHER, THE POLE SECTIONS
SHOULD HAVE A 3-1/2" MINIMUM
OVERLAP, LEAVING 1-1/2" BETWEEN
THE OVERLAPPING POLE AND THE
IDENTIFICATION STICKER.
2
OVERLAP.
IDENTIFICATION
STICKER
m i d d l e p o l e
POLE
IDENTIFICATION
MARK
5"
1
IDENTIFICATION
STICKER
m i d d l e p o l e
1-1/2"
WOOD SCRAP
(NOT SUPPLIED)
9
08/05
P/N M601111
Download from Www.Somanuals.com. All Manuals Search And Download.
Align dimple of middle pole with slot of bottom pole.While maintaining alignment, bounce
top and middle pole assembly (1 & 2) onto lower pole section (3) as shown until they no
longer move toward pole identification mark.
3.
CAUTION!
THE IDENTIFICATION STICKER IS
LOCATED 5" FROM THE END OF
THE POLE. WHEN PROPERLY
POUNDED TOGETHER, THE POLE
SECTIONS SHOULD HAVE A 3-1/2"
MINIMUM OVERLAP, LEAVING 1-1/2"
BETWEEN THE OVERLAPPING
POLE AND THE IDENTIFICATION
STICKER.
5"
Bottom Pole
IDENTIFICATION
STICKER
NOTE:
POLE SECTIONS
SHOULD HAVE A
3-1/2" (9 CM)
MINIMUM
1
OVERLAP.
1-1/2"
IDENTIFICATION
STICKER
Bottom Pole
POLE
IDENTIFICATION
MARK
2
RODS SHOWN ARE
FOR VISUAL
REPRESENTATION
OF ALIGNMENT
AND ARE NOT
SUPPLIED WITH
THE HARDWARE
3
IMPORTANT!
Holes in top (1) and bottom (3)
pole sections MUST align to
correctly position elevator
system toward playing
surface.
WOOD SCRAP
(NOT SUPPLIED)
10
P/N M601111 08/05
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION B: ASSEMBLE THE BASE
This is what your system will look like
when you’ve finished this section:
TOOLS REQUIRED FOR THIS SECTION
(2) 1/2”Wrenches
(2) Socket Wrenches
and Sockets
AND/OR
1/2”
AND
Hammer or
Mallet
11
08/05
P/N M601111
Download from Www.Somanuals.com. All Manuals Search And Download.
Assemble pole bracket (12) using bolt (13) and
Lock Nut (14) as shown.
1.
IMPORTANT!
DO NOT OVER
TIGHTEN
2.
Attach pole assembly to base
using carriage bolts (15)
washers(10) and nuts (11) as
shown. Two people are required
for this step.
13
14
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT
IN SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
12
15
IMPORTANT!
THE CUT CORNERS OF
THE POLE BRACKET
NEED TO FACE TOWARD
THE BACK OF THE BASE
AS SHOWN.
10
11
12
P/N M601111 08/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure tank struts (16) to pole as shown.
Nut should be tightened until flush (even) with lock nuts outer edge. Place cap (17) over
exposed end of bolt as shown.
3.
10
10
17
13
WARNING!
14
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT
IN SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
16
Rotate non-secured ends of tank struts (16) outward to mounting holes in tank as
shown.Secure ends of tank struts (16) to tank as shown. Repeat for opposite side.
4.
16
9
16
10
10
11
13
08/05
P/N M601111
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert axle (5) through wheel bracket (4). Secure wheels (6) to axle using pushnuts (7).
Carefully tap pushnuts onto axle with hammer or mallet
5.
IMPORTANT!
6
7
4
5
6
7
SIDE OF WHEEL WITH
LONGER PLASTIC AXLE
NEEDS TO FACE THE
WHEEL BRACKET.
Install wheel assembly to base (8) using bolts(9),
washers(10) and nuts (11) as shown.
6.
9
10
NOTE:
CAREFULLY TIPPING THE
SYSTEM ON IT'S SIDE WILL
ALLOW EASIER ACCESS
TO THE UNDERSIDE OF
8
BASE.
10
11
14
P/N M601111 08/05
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION C: ASSEMBLE THE ELEVATOR & BACKBOARD
This is what your system will look like
when you’ve finished this section:
TOOLS REQUIRED FOR THIS SECTION
(1) 3/8”, (2) 1/2”, (2) 9/16” and
(2) 3/4” Wrenches
(2) Socket Wrenches and Sockets
AND/OR
3/4”
3/8” 1/2”
9/16”
Phillips Screwdriver
15
08/05
P/N M601111
Download from Www.Somanuals.com. All Manuals Search And Download.
Install pole mount bracket (28) and reinforcement bracket (18) with carriage bolts (22) as
shown. Tighten flange nuts (11) completely.
1.
22
18
1
22
28
11
11
Attach spacers (24, 43) to pole mount bracket (28) with bolts (29), washers (50), and lock
nuts (31) as shown.
2.
IMPORTANT!
Tighten just until
washers (50) stop
28
50
moving.
31
50
50
50
24
29
43
43
24
16
P/N M601111 08/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Assemble lanyard (26) to locking pin (27) as shown (FIG A). Attach covers (35) onto pole
mount bracket (28) with carriage bolt (19) and nut (11) as shown.
3.
FIG. A
35
11
28
35
IMPORTANT!
19
19
Loop end of pin
lanyard (26) over
26
carriage bolt (19) as it
passes through the
pole mount bracket (28)
26
27
27 during this assembly.
Apply logo and height indicator labels (23) to
adjustment rod (58) as shown. Attach handle parts
(59, 60) to adjustment rod with screw (55), carriage
bolts (54), and flange nuts (11) as shown.
4.
23
58
IMPORTANT!
23
Indicator labels should
be applied as close to
holes as possible to
prevent labels from
being damaged during
height adjustment.
11
60
54
55
11
59
54
17
08/05
P/N M601111
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert handle assembly through pole mount assembly as
shown. Lock pole assembly in place at the 10’ (3.05 m)
mark with pin (27).
5.
27
30
30
29
Assemble backboard brackets (52)
using bolts (29), and nuts (30) as
shown.
52
6.
29
52
18
P/N M601111 08/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Assemble board pad to board.
7.
A
Work from the center - out.
Using the holes which line up for your
board size, attach center pad (48), right
pad (45) and left pad (44) sections to
board using screws (46) and washers (47)
as shown.
IMPORTANT!
DO NOT TIGHTEN
HARDWARE
COMPLETELY.
48
47
45
BOARD STYLE MAY
VARY
47
44
46
46
Secure left (44) and right (45) pad sections to
board by pushing pads over the corners of the
board. Secure completely by using screws (46)
and washers (47) as shown.
B
46
47
IMPORTANT!
TIGHTEN ALL
HARDWARE
COMPLETELY.
45
47
BOARD STYLE MAY
47
46
VARY
46
48
47
46
44
19
08/05
P/N M601111
Download from Www.Somanuals.com. All Manuals Search And Download.
Identify elevator tubes (33 & 34).
8.
Toward
Board
Toward
Pole
33
34
Upper Elevator tube
Lower Elevator tube
Toward
Board
Toward
Pole
Attach lower elevator tubes (34) and counter balance spring (36) to backboard support
brackets (52) using spacers (53 & 56), bolt (57), and nut (21) as shown.
53
21
36
52
34
56
56
36
57
34
66
52
52
68
20
P/N M601111 08/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach upper elevator tubes (33) to backboard support brackets (52) using spacers
(53), bolt (57), and nut (21) as shown.
9.
IMPORTANT!
Tighten ALL Hardware
from Steps 6-8 After this
Assembly is Completed.
21
53
56
33
52
56
33
57
21
53
56
33
56
33
57
21
08/05
P/N M601111
Download from Www.Somanuals.com. All Manuals Search And Download.
Support pole on sawhorse. Attach backboard assembly to top pole section (4) as
shown. Install pole cap (25).
10.
WARNING!
21
USE CAUTION; ELEVATOR
ASSEMBLY IS HEAVY.
34
20
TWO PEOPLE REQUIRED FOR
1
21
THIS PROCEDURE. FAILURE
TO FOLLOW THIS WARNING
COULD RESULT IN SERIOUS
INJURY AND/OR PROPERTY
DAMAGE.
32
25
32
49
20
34
57
Install upper elevator tubes (33) to triangle plates (63) as shown. Install handle assembly
to lower elevator tubes (34) using bolt (57), spacers (20), and nut (21) as shown.
11.
21
21
20
33
58
20
1
20
34
32
34
34
NOTE:
Before going on to
next step, set
20
57
adjustable system
assembly to the
10’ (3.05 m) setting.
57
33
22
P/N M601111 08/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Install Rim to Backboard
A. Fit rim (67) securely into bracket (61) as shown. Allow T-bolt (66) to slip through center hole
12.
in rim (67).
B. Install reinforcement bracket (62) onto T-bolt (66) as shown.
C. Install spring (64) onto T-bolt (66) as shown.
D. Install special nut (65) and washer (63) onto T-bolt (66).
E. Tighten special nut (65) until flush with end of T-bolt (66).
A.
B.
NOTE:
62
ORIENTATION
OF BRACKET
67
66
66
61
62
65
63
C.
D.
64
66
63
66
65
E.
23
08/05
P/N M601111
Download from Www.Somanuals.com. All Manuals Search And Download.
Install net (43).
13.
D.
B.
C.
A.
Insert bolt (57) through left side upper elevator tube (33), then stretch spring (36) onto
bolt (57). Insert bolt (57) through right side upper elevator tube (33) and secure with
nut (21).
14.
WARNING!
USE EYE PROTECTION
WHEN INSTALLING
SPRINGS.
NOTE:
Peel protective
film from surface
of acrylic
21
33
36
backboard prior
to use.
57
33
36
58
24
P/N M601111 08/05
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION D: FILL BASE
TOOLS REQUIRED FOR THIS SECTION
Garden Hose or Sand
Roll assembly to desired playing area. Fill base (8) with water (approx. 40 gallons) and
snap base plugs (37) in place.
1.
WARNING!
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
DO NOT LEAVE
ASSEMBLY UNATTENDED
WHEN EMPTY; IT MAY TIP
OVER.
CAUTION!
ADD TWO GALLONS (7.6 LITERS)
OF NON-TOXIC ANTIFREEZE IN
SUB-FREEZING CLIMATES.
37
37
NOTE:
IF USING SAND:
2 GALLONS OF
ANTI-FREEZE IS
NOT REQUIRED
8
25
08/05
P/N M601111
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION E: INSTALL FRONT COVER
TOOLS REQUIRED FOR THIS SECTION
Scissors
Install front cover (38) by lining up stand-offs along the tank struts. Insert a tie strap (39)
through the top two and bottom two stand offs. Wrap tie straps around tank struts as
shown and secure tightly. Trim excess of tie strap as shown in FIG.A.
1.
38
STANDOFFS
39
FIG. A
26
P/N M601111 08/05
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION F: INSTALL RIM COVER
TOOLS REQUIRED FOR THIS SECTION
Phillips
Screwdriver
Install cover (40) over spring return mechanism with screws (41) as shown.
Place NBA label (51) on front of rim cover (40).
1.
41
41
40
51
27
08/05
P/N M601111
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION G: HEIGHT ADJUSTMENT AND MOVING LABEL
Apply Height Adjustment and Moving Label (42) to front of pole, where it is clearly
visible.
1.
HEIGHT ADJUSTMENT
TO ADJUST BACKBOARD:
1
3
1. While holding handle, remove pin.
2. Move elevator up or down to
desired height.
2
3. Replace pin full length to lock
system at desired height.
2
MOVING SYSTEM
1. Adjust basketball backboard
height to lowest position.
1
2. While holding pole, rotate
basketball system forward
until wheels engage with
ground.
3. Move basketball system to
desired location.
2
4.
Carefully rotate basketball
system upright.
3
4
5.
Checksystem for stability.
511679
05/05
42
A. While holding handle, remove pin (27).
B. Move elevator up or down to desired height.
C. Replace pin (27) full length to lock system at
desired height.
2.
27
A.
C.
58
WARNING!
DO NOT ALLOW
CHILDREN TO
ADJUST HEIGHT.
B.
28
P/N M601111 08/05
Download from Www.Somanuals.com. All Manuals Search And Download.
|