Portable Basketball System
Owners Manual
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
Customer Service Center
REQUIRED TOOLS AND MATERIALS:
• Two People
• Wood Board (Scrap)
WARNING!
• Tape Measure
• Step Ladder 8 ft. (2.4 m)
• Tape
• Garden Hose or Sand 360 lb. (163 kg)
• Hammer
• Wrenches: (Two) 3/4”, (One) 1/2” (Two) 9/16”or
equivalent sockets, (One) 1/2” Deep well socket
with extension and socket wrench
• Support Table
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO PROPERTY.
• Phillips Head Screwdriver
• 5/32 Allen Wrench
Toll-Free Customer Service Number for U.S: 1-800-558-5234,
For Canada: 1-800-284-8339,
For Europe: 00 800 555 85234 (Sweden: 009 555 85234),
For Australia: 1-800-632-792
Internet Address: www.huffysports.com
1
02/04
P/N 211789
© COPYRIGHT 2004 by HUFFY SPORTS
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully. Proper
and complete assembly, use, and supervision are essential for proper operation and to reduce the risk of
accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and
operated properly.
•
•
If using a ladder during assembly, use extreme caution.
Check base regularly for leakage. Slow leaks could cause the system to tip over
unexpectedly
•
Seat the pole sections properly (if applicable). Failure to do so could allow the pole
sections to seperate during play and/or during transport of the system.
Climate, corrosion or misuse could result in system failure.
If technical assistance is required, contact Huffy Sports.
Minimum operational height is 6'-6" (1.98m) to the bottom of backboard.
•
•
•
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this unit.
NOTICE TO ASSEMBLERS
ALL Huffy Sports basketball systems, including those used for DISPLAYS, MUST be assembled
and ballasted with sand or water according to instructions. Failure to follow instructions could
result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system.
IMPORTANT!
Remove all contents from boxes.
Be sure to check inside pole sections;
hardware and additional parts are packed inside.
WARRANTY CARD:
Please remember to complete your product
registration form either on-line at:
www.huffysports.com/warrantycard or mail-in
the enclosed postcard.
3
02/04
P/N 211789
Download from Www.Somanuals.com. All Manuals Search And Download.
Get to know the basic parts of your basketball system.....
FRONT
BACK
BACKBOARD
RIM
ELEVATOR
ASSEMBLY
TOP POLE
BOTTOM
POLE
MIDDLE POLE
STRUTS
FRONT
COVER
BASE
WHEEL
CARRIAGE
ASSEMBLY
4
P/N 211789
02/04
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST (SEE HARDWARE IDENTIFIER)
ItemQty
Part No
Description
ItemQty
Part No
Description
1
2
3
4
5
6
7
8
1
1
1
2
2
2
4
1
1
1
8
1
1
2
1
1
1
2
1
4
1
900467
904811
903407
900223
206940
226403
206938
200117
203223
202662
203218
200188
202822
906410
200516
200123
206948
900122
200512
203232
206252
203100
203330
203527
203528
203103
203540
201129
803531
803553
203593
203688
900867
Top Pole Section
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
1
4
1
9
2
4
8
1
4
2
2
1
2
3
7
2
1
4
207103
908119
808115
206340
203053
202862
204847
201139
201682
203798
202273
203099
200874
206360
203063
900964
200118
265601
201219
204290
206219
203124
201568
203532
240027
203535
203536
203537
240019
202274
206956
226401
203309
Pole Cap
Elevator Tube
Pole Bracket
Middle Pole Section (with Label)
Bottom Pole Section
Wheel Bracket
Axle
Wheel 6”
Pushnut
Base
Carriage Bolt, 5/16-18 x 1
Hex Bolt, 5/16-18 x 4.5
Washer 5/16
Nut, Nylock, 1/2 -13
Bolt, Carriage, 5/16-18 x 4
Spacer, Plastic, .50 O.D., 1.19" Long
Bolt 1/2 -13 x 9.5
Bolt 1/2 -13 x 4.5
Spacer, Plastic, .50 O.D., 1.88" Long
Bolt 5/16-18 x 1.5
Spacer, Metal, .50 O.D., 5-7/8" Long
Nut, Nylock, 5/16-18
Spacer, Metal, .50 O.D., 1.53" Long
Bolt 3/8 -16 x 2.625
Nut 3/8 -16 Nylock
Board Brackets
9
10
11
12
13
14
15
16
17
18
19
20
21
Rod 3/8 x 5.25
EyeBolt 3/8 -16 x 3.75
Tank Strut
Bolt Cover
Upper Pivot Bracket
Lower Pivot Bracket
Hinge Tubes
Hex Bolt, 3/8 -16 x 3.5
Flat Washer 3/8 -3/4
Hex Bolt, 3/8 -16 x 1
Flange Nut 5/16 -18
Hex Bolt, 3/8 -16 x 4.5
Spacer, Plastic, .75" O.D., 1.53" Long
Spacer, Plastic, 1.25" O.D., 1.53" Long
Carriage Bolt, 5/16-18 x 2
Height Indicator Window
Spacer, Metal, .50" O.D., 1.8" Long
Strut Assembly
Front Cover
Front Cover Carriage Bolts
Net Clips
Net
Base Plug
Tie Down Stake
Anchor Strap
Label Height Adjustment
Nut, Nylock 1/4-20
Strip
Height Label
Hook
Bolt 1/4-20 x .75
52 12
53
54
55
56
57
58
59
60
61
62
63
64
65
66
1
1
1
1
1
2
1
1
1
1
2
1
2
2
22 13
23
24
25
26
27
28
29
30
31
32
33
1
2
2
4
1
1
1
1
1
2
2
Handle Assembly
Shoulder Bolt
Spacer, Plastic, .75" O.D., 2.25" Long
Triangle Plates
Spacer, Metal, .50 O.D., 3-1/2" Long
Plastic Disc
Wheel 4”
Washer, Flat, 3/8-1
* You may have extra parts with this model.
BEFORE YOU START!
To ensure optimal playability of backboard system, a
close tolerance fit between the elevator components
and hardware is required. Test-fit large bolts into large
holes of elevator tubes, backboard brackets, and
triangle plates. Carefully rock them in a circular motion
to ream out any excess paint from holes if necessary.
5
02/04
P/N 211789
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER (BOLTS & SCREWS)
Item #43 (2)
Item #13 (1)
Item #40 (8)
Item #41 (1)
Item #10 (1)
Item #23 (1)
Item #19 (1)
Item #47 (3)
Item #31 (1)
Item #9 (1)
Item #26 (4)
Item #51 (4)
Item #21 (1)
Item #38 (2)
Item #62 (1)
* You may have extra parts with this model.
6
P/N 211789
02/04
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER (NUTS, WASHERS & METAL SPACERS)
Item #58 (2)
Item #28 (1)
Item #37 (9)
Item #11 (8)
Item #22 (13)*
Item #20 (4)
Item #48 (7)
Item #45 (1)
Item #46 (2)
Item #66 (2)
Item #63 (2)
Item #44 (2)
HARDWARE IDENTIFIER (LABELS, PLASTIC SPACERS & CAPS)
Item #15 (1)
Item #24 (2)
Item #25 (2)
HEIGHT ADJUSTMENT
Item #39 (4)
Item #42 (4)
MOVING SYSTEM
1. Adjust basketball backboard
1
height to lowest position.
2. Rotate handle forward until
wheels engage ground.
3. Move basketball system to
desired location.
4. Rotate handle back to original
2
3
position.
5. Reattach ground restraint and
4
check system for stability.
203532
01/04
Item #32 (2)
Item #7 (4)
Item #57 (1)
7
02/04
P/N 211789
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION A: ASSEMBLE THE POLES
Correctly identify each pole section. Mark pole sections with tape as shown.
1.
1
3
2
5"
(13 cm)
5"
(13 cm)
TAPE
(not supplied)
TAPE
(not supplied)
Bounce middle pole section (2) into top pole section (1) together using a wood scrap as shown
until they no longer move toward taped reference mark.
2.
NOTE:
POLE SECTIONS
SHOULD HAVE A
3-1/2" (9 CM) MINIMUM
OVERLAP.
2
IMPORTANT!:
Position middle pole so
that the warning label is on
the same side as the 11/32"
(.87cm) diameter holes of
the top pole.
1
Wood Scrap
8
P/N 211789
02/04
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
IMPORTANT! Holes in top (1) and bottom pole (3) sections MUST align to correctly
position elevator system toward playing surface.
While maintaining alignment, bounce assembly and lower section (3) together as shown
until they no longer move toward taped reference mark.
NOTE:
POLE SECTIONS
SHOULD HAVE A
3-1/2" (9 CM) MINIMUM
OVERLAP.
11/32" (.87 cm) SMALLER
DIAMETER HOLES OF
TOP POLE
1
2
TAPE REFERENCE
MARK
3
WOOD SCRAP
(NOT SUPPLIED)
9
02/04
P/N 211789
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION B: ASSEMBLE THE BASE
This is what your system will look like when
you’ve finished this section:
HARDWARE USED IN THIS SECTION
(not actual size)
TOOLS REQUIRED FOR THIS SECTION
1/2” & 9/16”
Item #48
Item #9
AND
Item #7
Item #45
Item #10
Item #15
Item #11
Item #13
9/16” & 1/2” AND EXTENSION
HAMMER OR MALLET
Item #20
Item #19
Item #22
Item #23
Item #21
Item #43
Item #26
10
P/N 211789
02/04
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert axle (5) through wheel bracket (4). Secure wheels (65) to axle using
pushnuts (7). Carefully tap pushnuts onto axle with hammer or mallet
1.
65
7
4
5
65
7
Install wheel assembly to base (8) using bolt (9), and nut (22) as shown.
2.
9
8
9
22
11
02/04
P/N 211789
Download from Www.Somanuals.com. All Manuals Search And Download.
Install rod (12) through holes in bottom pole section (3) and eyebolt (13).
Insert pole assembly into tank (8) and through center hole on wheel assembly as shown. Secure pole
assembly with anchor strap (56), washer (11), and lock nut (48).
3.
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
12
1
2
IMPORTANT!:
Smaller holes (11/32"/ .87
3
cm) of top pole should
13
face toward the front of the
system and the warning
label should be facing
toward the front.
12
8
13
11
48
56
12
P/N 211789
02/04
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure tank struts (14) to pole as shown.
Place cap (15) over exposed end of bolt as shown.
4.
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
3
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
45
11
11
10
PROPERTY DAMAGE.
15
14
Rotate non-secured ends of tank struts (14) outward to mounting holes in
tank as shown.
14
14
13
02/04
P/N 211789
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure ends of tank struts (14) to tank as shown. Repeat for opposite side.
5.
43
WARNING!
14
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
11
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
11
22
Install upper pivot bracket (16) to front of base using bolt (19), washer (20) and nut (48) as shown.
6.
48
20
16
19
14
P/N 211789
02/04
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert bolt (21) through lower pivot bracket (17) as shown; bolt (21) will be
secured during step 10. Carefully place base assembly on its side. Install lower
pivot bracket (17) with bolt (23), washers (20), and lock nut (48) as shown.
7.
IMPORTANT!:
DO NOT OVER
TIGHTEN
21
48
16
20
20
17
23
Secure both hinge tubes (18) to second wheel bracket (4) with carriage bolts (26)
and flange nuts (22).
8.
26
18
4
22
15
02/04
P/N 211789
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert axle (5) through wheel bracket (4). Secure wheels (6) to axle using
pushnuts (7). Carefully tap pushnuts onto axle with hammer or mallet
9.
6
IMPORTANT!:
4
7
5
6
7
SIDE OF WHEEL WITH
LONGER PLASTIC
AXLE NEEDS TO FACE
THE WHEEL BRACKET.
Position base as shown. Secure wheel bracket assembly with
disc (64), washer (20) and nut (48) as shown.
10.
IMPORTANT!:
21
DO NOT OVER
TIGHTEN
64
20
48
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
Carefully reposition entire assembly as shown:
16
P/N 211789
02/04
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION C: ASSEMBLE THE ELEVATOR SYSTEM & BACKBOARD
This is what your system will look like when
you’ve finished this section:
HARDWARE USED IN THIS SECTION
TOOLS REQUIRED FOR THIS SECTION
(not actual size)
WRENCHES
(2) 1/2”, (2) 3/4”
AND (2) 9/16”
Item #31
Item #11
Item #22
Item #41
Item #40
Item #42
Item #47
Item #48 (6)
Item #37
AND/OR
Item #38
Item #39
Item #63
Item #62
Item #24
Item #58
Item #25
1/2”, 9/16”, 3/4" & EXTENSION
AND (1) 5/32 Allen Wrench
Item #46
Item #28
Item #32
Item #66
Item #44 (2)
17
02/04
P/N 211789
Download from Www.Somanuals.com. All Manuals Search And Download.
Securely rest the assembly on sawhorse. Install pole bracket (36) to top pole as shown (FIG.A)
using bolts (38), metal spacers (63) and nuts (22). Reference finished assembly (FIG.B.)
1.
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
COMPLETED ASSEMBLY
38
36
36
63
63 & 38
22
22
FIG.A
FIG.B
FLAT SIDE
TOWARDS BASE.
18
P/N 211789
02/04
Download from Www.Somanuals.com. All Manuals Search And Download.
Identify elevator tubes.
2.
Install triangle plates (33) and elevator tubes (35) to top pole section (1) as shown.
Install pole cap (34) at this time.
Toward
Pole
Toward
Board
35
Upper & Lower Elevator tube
37
35
37
35
39
34
33
1
33
COMPLETED ASSEMBLY
39
41
39
35
40
35
40
19
02/04
P/N 211789
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach label (60) to window (27).
Important: Line up top edge of label with top edge of window
3.
COMPLETED
ASSEMBLY
27
60
Remove packaging materials and zip ties from handle assembly (30)
Snap window into handle assembly (30)
4.
30
COMPLETED ASSEMBLY
20
P/N 211789
02/04
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert strut assembly (29) over inner channel (A) and between
outer channel (B). Rest at angle shown in fig. A. Line up holes
in strut bracket to holes in outer channel (B)
5.
29
Strut bracket
COMPLETED ASSEMBLY
ORIENT STRUT ASSEMBLY
SO CLIP-HANDLE FACES
LONG SIDE OF CHANNELS
30A
30B
WARNING!
FIG. A
IMPORTANT!:
TO AVOID RAPID
EXTENSION OF STRUT
ROD - DO NOT DEPRESS
BUTTON ON GAS STRUT
ASSEMBLY.
DO NOT REMOVE CLIP
UNTIL SECTION F, STEP 1.
THIS CLIP PREVENTS
PREMATURE EXTENSION
OF GAS STRUT.
Insert metal spacer (22) through outer channel (B), strut
bracket and inner channel (A). Center spacer on outer
channel.
6.
COMPLETED ASSEMBLY
NOTE: To allow spacer to fit through, lift inner channel
(A) to help line up holes with outer channel (B).
29
29
44
30A
30B
44
21
02/04
P/N 211789
Download from Www.Somanuals.com. All Manuals Search And Download.
58
7.
59
62
Attach hook (59) to strip (61)
and secure with bolt (62) and
nut (58).
61
Install hook and strip assembly into
handle assembly.
8.
Bring strip through top of height indicator window
(27) underneath tabs and insert through bottom
end of height indicator window (27).
IMPORTANT!:
TO AVOID RAPID
EXTENSION OF STRUT
ROD - DO NOT DEPRESS
BUTTON ON GAS STRUT
ASSEMBLY.
9.
IMPORTANT!:
TABS
61
61
STRIP(61) MUST PASS
UNDERNEATH ALL 6 TABS OF
HEIGHT INDICATOR WINDOW (27).
61
22
P/N 211789
02/04
Download from Www.Somanuals.com. All Manuals Search And Download.
10.
Attach strut (29) to pole
bracket (36) with bolt
(31), washers (11), and
nut (58) as shown.
58
11
11
29
36
35
31
IMPORTANT!:
TO AVOID RAPID
EXTENSION OF STRUT
ROD - DO NOT DEPRESS
BUTTON ON GAS STRUT
ASSEMBLY.
35
Slip plastic spacers (25) onto metal spacer (44) that is already inserted into handle
assembly. Then, secure handle assembly to elevator tubes (35) using bolts (40), plastic
spacers (24) and nuts (37).
11.
37
44
25
24
24
37
40
25
40
23
02/04
P/N 211789
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure strap and hook assmbly to upper elevator arms (35) using bolt (40), plastic spacers
(32) and nut (37) as shown.
12.
35
37
32
35
40
COMPLETED ASSEMBLY
24
P/N 211789
02/04
Download from Www.Somanuals.com. All Manuals Search And Download.
Assemble brackets (49) to backboard using bolts (47) metal spacers (46) and nuts (48) as shown.
The spacers may fit very tightly between the brackets and may need to be tapped into place with
a hammer.
13.
46
49
46
48
47
48
46
48
Face of Backboard
47
49
47
IMPORTANT!:
DO NOT TIGHTEN
HARDWARE
COMPLETELY.
Secure metal spacer (28) between board brackets (49) with bolt (47), washer (66), and nut (48).
14.
48
28
66
66
IMPORTANT!:
47
TIGHTEN ALL HARDWARE
FROM STEP 13 AND 14
COMPLETELY AFTER THIS
STEP.
25
02/04
P/N 211789
Download from Www.Somanuals.com. All Manuals Search And Download.
Assemble lower elevator tubes (35) and rim to brackets (49) using
bolts (40), plastic spacers (42), metal spacer (44) and nuts (37) as
shown.
15.
35
49
44
37
42
40
42
NOTE:
Refer To Instructions Included
With Rim Hardware For Rim
Assembly.
Use the 5/16-18 x 1" hex-flange
bolts for installing rim to the
acrylic backboard.
26
P/N 211789
02/04
Download from Www.Somanuals.com. All Manuals Search And Download.
Assemble upper elevator tubes (35) to brackets using bolt (40), plastic spacers (42), and nut
(37) as shown.
16.
37
42
49
42
40
35
35
Item #42
27
02/04
P/N 211789
Download from Www.Somanuals.com. All Manuals Search And Download.
Install net clips.
17.
CLIP “ARM”
WARNING!
USE OF THIS PRODUCT
WITHOUT PROPER
52
INSTALLATION OF SMART
CLIPS®, OR WHEN ALL SMART
CLIPS® ARE NOT PRESENT
COULD RESULT IN BODILY
HARM. BE SURE TO FOLLOW
DIRECTIONS CAREFULLY.
CLIP “BODY”
Insert one “arm” of clip (52) into ram as shown. Twist “body” of
clip slightly so that second “arm” slides over the top of the first
“arm” as shown.
Push in direction indicated by arrows.
52
A
Push second “arm” back and into ram as shown.
B
Twist “body” of clip slightly again to spread “arms” of clip.
Clip “arms” must be flat and touching edge-to-edge as shown,
without overlapping.
C
28
P/N 211789
02/04
Download from Www.Somanuals.com. All Manuals Search And Download.
Install net.
18.
SIDE VIEW
52
NETCLIP
53
NET
Insert net into bottom of clip as shown.
8
SIDE VIEW
Twist net until it snaps into position.
Net must be centered through clip.
NETCLIP
NET
29
02/04
P/N 211789
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION D: INSTALL FRONT COVER & HANDLE
Upright system and fill base (8) with water (approx. 40 gallons) and snap fill cap (54) in place.
1.
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
54
PROPERTY DAMAGE.
WARNING!
DO NOT LEAVE
ASSEMBLY UNATTENDED
WHEN EMPTY; IT MAY TIP
OVER.
CAUTION!
ADD TWO GALLONS (7.6
LITERS) OF NON-TOXIC
ANTIFREEZE IN SUB-
FREEZING CLIMATES.
Attach front cover (50) to hinge tubes (18) using carriage bolts (51) and flange nuts (15)
as shown.
2.
18
22
50
51
30
P/N 211789
02/04
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION E: SECURING THE SYSTEM
Roll assembly to desired playing area. Secure assembly to
ground using strap (56) and tie down stake (55).
1.
8
56
55
31
02/04
P/N 211789
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION F: APPLY HEIGHT AND MOVING LABEL
Apply Height Adjustment and Moving Label (57) to front of pole, where it is clearly visible.
1.
Remove strut locking clip.
NOTE:
Peel protective
film from surface
of acrylic
backboard prior
to use.
57
HEIGHT ADJUSTMENT
MOVING SYSTEM
1. Adjust basketball backboard
1
height to lowest position.
2. Rotate handle forward until
wheels engage ground.
3. Move basketball system to
desired location.
4. Rotate handle back to original
position.
2
3
5. Reattach ground restraint and
check system for stability.
4
203532
01/04
32
P/N 211789
02/04
Download from Www.Somanuals.com. All Manuals Search And Download.
|