IMPORTANT FOR FUTURE REFERENCE
Please complete this information and retain this
manual for the life of the equipment:
Model #: __________________________
Serial #: __________________________
Date Purchased: ___________________
OPERATOR’S MANUAL
Super Simple Steam
SEZ Series Countertop Steamers
For Models SEZ/3 & SEZ/5 Built After February 15, 2001
Model SEZ/3
! WARNING
Improper installation, operation, service, or maintenance can cause property damage, injury, or death.
Read this manual thoroughly before installing and operating this equipment.
1100 Old Honeycutt Road, Fuquay-Varina, NC 27526
(800) 348-2558 or (919) 552-9161 • FAX (800) 348-2558 or (919) 552-9798
COUNTERTOP STEAMER
MANUAL 1183437
$18.00
MANUAL SECTION ST
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
TABLE OF CONTENTS
Congratulations! You have purchased one of the finest pieces of heavy-duty commercial cooking equipment
on the market.
You will find that your new equipment, like all Southbend equipment, has been designed and manufactured
to meet the toughest standards in the industry. Each piece of Southbend equipment is carefully engineered
and designs are verified through laboratory tests and field installations. With proper care and field
maintenance, you will experience years of reliable, trouble-free operation. For best results, read this
manual carefully.
RETAIN THIS MANUAL FOR FUTURE REFERENCE.
Table of Contents
Specifications..........................................................................................................................4
Installation...............................................................................................................................6
Operation ..............................................................................................................................12
Cooking Hints........................................................................................................................13
Cleaning................................................................................................................................16
Troubleshooting ....................................................................................................................18
Parts......................................................................................................................................40
Read these instructions carefully before attempting installation. Installation and initial startup should be
performed by a qualified installer. Unless the installation instructions for this product are followed by a
qualified service technician (a person experienced in and knowledgeable with the installation of commercial
gas an/or electric cooking equipment) then the terms and conditions on the Manufacturer’s Limited Warranty
will be rendered void and no warranty of any kind shall apply.
In the event you have questions concerning the installation, use, care, or service of the product, write to:
Technical Service Department
Southbend
1100 Old Honeycutt Road
Fuquay-Varina, North Carolina 27526 USA
The serial plate is located on the right side of the unit near the back and top.
OPERATOR’S MANUAL 1183437
PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
SEZ SERIES COUNTERTOP STEAMERS
SPECIFICATIONS
DIMENSIONS
Figure 1
16.3"
31.4"
See
table
below
FRONT VIEW
SIDE VIEW
REAR VIEW
2.1"
Water Inlet
Electrical Connection
Water Drain
15.2"
2.0"
0.8"
2.4"
13.8"
Interior Dimensions
Pan Capacity*
Crate Dimensions
Overall
Height
Crated
Weight
Model
Width
Depth
22.0"
22.0"
Height
1"
6
2.5"
3
4"
2
Width
19.5"
19.5"
Depth
31.5"
31.5"
Height
28.5"
34.5"
SEZ/3
SEZ/5
19.0"
25.0"
13.5"
13.5"
9.5"
150 lbs.
175 lbs.
15.5"
9
5
3
* “Pan Capacity” is the number of 1", 2.5", or 4" high standard pans (12" wide x 20" deep) that the steamer will hold.
PAGE 4
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
SPECIFICATIONS
ELECTRICAL REQUIREMENTS
One electrical connection is required to the fuse block of the steamer. All units shipped per customer order,
three phase or single phase (a kit is available for field conversion to three phase or single phase). Circuit
must be wired for the maximum amps at required voltage.
Total Connected Amps
Voltage
Model SEZ/3
Model SEZ/5
1 Phase
3 Phase
1 Phase
3 Phase
208 V
220 V
240 V
480 V
44
41
38
19
25
57
54
49
25
33
24
31
22
29
11
15
WATER REQUIREMENTS
To meet warranty requirements, the water supply must be as follows:
1/4" NPT (female)
Connection
cold water
Pressure
30 to 60 PSI
60 PPM
Total Dissolved Solids (TDS)
Hardness
pH
2 grains or 35 PPM
7.0 to 7.5
Typical usage is 0.02 gpm. Maximum instantaneous usage is 0.12 gpm.
In order to minimize service problems and to meet the warranty requirements, a water treatment system
(softener) is recommended when water quality does not meet the limits stated above.
DRAIN REQUIREMENTS
The drain outlet has a 3/8" NPT (male) connector. DO NOT directly connect the drain to a plumbing system
unless you also install an “open funnel” downstream of this connection. There must be no back-flow or back-
pressure into the drain connection!
CONSTRUCTION SPECIFICATIONS
Exterior: Type 304 stainless steel with #3 sanitary finish.
Interior: #304 stainless steel.
Power Source: One electric power source for controls and heating elements, as well as one ground wire.
A positive ground connection is essential.
Cooking Compartment: Fully insulated.
CONTROLS
ON/OFF Lever: In the “OFF” position, the power is off and the drain valve is open. In the “ON” position, the
power is on and the drain valve is closed.
60 Minute Timer: Time can be set between 1 and 60 minutes. When time expires, buzzer sounds. Buzzer
can be disabled by turning the knob to manual position. Timer has no effect on the operation of the
steamer.
“SERVICE REQUEST” Light: Unit signals when service is needed.
“ON” Light: Indicates power is on.
OPERATOR’S MANUAL 1183437
PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
SEZ SERIES COUNTERTOP STEAMERS
INSTALLATION
!
CAUTION
Do not locate unit adjacent to any high heat or grease producing piece of equipment, such as a range
top, griddle, fryer, etc., that could allow radiant heat to raise the exterior temperature of the steamer
body above 130°F (54°C). DO NOT MOUNT ABOVE OTHER COOKING EQUIPMENT.
NOTICE
These installation procedures must be followed by qualified personnel or warranty will be void.
Local codes regarding installation vary greatly from one area to another. The National Fire Protection
Association, Inc. states in its NFPA 96 latest edition that local codes are the “authority having
jurisdiction” when it comes to installation requirements for equipment. Therefore, installations should
comply with all local codes.
The unit, when installed, must be electrically grounded and comply with local codes, or in the
absence of local codes with the National Electrical Code ANSI/NFPA 70-latest edition.
Canadian installation must comply with CSA-Standard (C22.2 No.
109-M1981 General
Requirements-Canadian Electrical Code, Part II. 109-M1981) Commercial Cooking Appliances.
NOTICE
EXHAUST FANS AND CANOPIES: It is recommended that the steamer be installed under a
ventilation hood. Consult local codes for proper installation of hoods. Proper ventilation is the
owner’s responsibility. Any problem due to improper ventilation will not be covered by warranty.
LEVELING: Unit must be level to assure maximum performance. Improper leveling may void
warranty.
Step 1: Unpacking
IMMEDIATELY INSPECT FOR SHIPPING DAMAGE
All containers should be examined for damage before and during unloading. The freight carrier has
assumed responsibility for its safe transit and delivery. If damaged equipment is received, either
apparent or concealed, a claim must be made with the delivering carrier.
Apparent damage or loss must be noted on the freight bill at the time of delivery. The freight bill must
then be signed by the carrier representative (Driver). If the bill is not signed, the carrier may refuse
the claim. The carrier can supply the necessary forms.
A request for inspection must be made to the carrier within 15 days if there is concealed damage or
loss that is not apparent until after the equipment is uncrated. The carrier should arrange an
inspection. Be certain to hold all contents plus all packing material.
PAGE 6
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
INSTALLATION
Step 2: Installation
1. Uncrate carefully. Report any hidden damage to the freight carrier IMMEDIATELY.
2. Do not remove any tags or labels until unit is installed and working properly.
3. If unit is to be installed on legs, locate legs and install as shown in Figure 2 below.
Figure 2
4. If the unit is to be installed on a counter top or other surface without using legs, the unit must be sealed
to the surface to prevent any water, grease, etc., from accumulating under the steamer. The steamer
can be bolted to the counter but will still have to be sealed. The installer may use G.E. or Dow
Corning RTV type sealant. Consult local code for exact requirements. See Figure 3 on next page.
OPERATOR’S MANUAL 1183437
PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Figure 3
SEZ SERIES COUNTERTOP STEAMERS
Steamer
Sealer
BOTTOM VIEW
Sealant
PAGE 8
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
INSTALLATION
Step 3: Electrical Connection
A field connection Fuse Block is located at the rear of the unit, lower left side when facing the back of the unit
(see Figure 4 below). A hole is provided for a 3/4" conduit fitting (solid or flex). The rear cover must be
removed to gain access to fuse block (see Figure 9 on page 26).
Be sure that the input voltage matches the requirement on the serial plate. The unit is factory wired per
customer order.
! WARNING
A POSITIVE GROUND CONNECTION IS ESSENTIAL. DO NOT ALLOW ANY TAMPERING OR
ADJUSTMENT OF ANY CONTROL OR WIRING. THE UNIT IS FACTORY SET. ADJUSTING ANY
INTERNAL COMPONENT OTHER THAN THE MAIN FUSE BLOCK CAN VOID THE WARRANTY.
THIS UNIT REQUIRES A KIT TO BE FIELD CONVERTED FROM THREE-PHASE TO SINGLE-
PHASE OR VICE-VERSA. CONSULT FACTORY FOR PHASE CHANGES.
All 208-220-240 and 480 volt units will have three fuse block sections, “L1-L2-L3”, for use with either 3-wire
3-phase or 2-wire, single-phase, 50 or 60 Hz.
Figure 4
Water Inlet
REAR VIEW
Water Drain
Electrical Connection
OPERATOR’S MANUAL 1183437
PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
SEZ SERIES COUNTERTOP STEAMERS
Step 4: Water Connection
! WARNING
Do not connect steamer to a hot water line. A hot water connection will damage the steamer.
NOTICE
To meet warranty requirements, the supply water must meet the following specifications:
Pressure
30 to 60 PSI
60 PPM
Total Dissolved Solids (TDS)
Hardness
pH
2 grains or 35 PPM
7.0 to 7.5
Connect a cold water line to the water inlet strainer on the back of the steamer, as shown in Figure 4 on
page 9. The connector on the unit is 1/4" NPT male.
NOTE: To facilitate cleaning, and allow access to rear of unit, flexible connections are recommended. A shut
off valve at (or near) the rear of the unit is highly recommended. See Figure 5 below.
Figure 5
Cold
Water
Supply
Steamer
Shut Off
Valve
Filter
Check
Valve
PAGE 10
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
INSTALLATION
Step 3: Drain Connection
The drain outlet is located on the back of the steamer, as shown in Figure 4 on page 9. The drain connector
on the unit is 3/8" NPT male.
Position the unit near, but not on top of, an open floor drain. DO NOT directly plumb to the unit unless you
also install an “open funnel” downstream of this connection in the drain system. Make the drain line from the
unit to the air gap above the “open funnel” as short as possible. There should be no horizontal piping
between the unit and the air gap above the “open funnel.” The “open funnel” is intended to eliminate any
water from entering the steamer because of a blocked drain, and it also prevents any back pressure within
the steamer cavity. Any connection that allows the build-up of back pressure in the unit (such as a reduction
in pipe size to a line smaller than 3/8", or more than one 90-degree angle in the line prior to the “open funnel”
drain discharge point) may cause personal or property damage and will therefore void the warranty. The unit
is a pressureless, free-venting steam cooker and will not operate properly unless the drain line is short, at a
steep angle, and open! See Figure 6 below.
Figure 6
Stand
Pipe
90°
Air Gap
Air Gap
Air Gap
Floor Drains
OPERATOR’S MANUAL 1183437
PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
SEZ SERIES COUNTERTOP STEAMERS
OPERATION
STARTUP
1. Turn lever to “ON” position.
2. Unit will fill automatically and be ready for operation in 11 minutes.
NOTICE: WATER SPECIFICATION
To meet warranty requirements, supply water must meet the following specification:
Total Dissolved Solids (TDS) ...........60 PPM
Hardness ..........................................2 Grains or 35 PPM
pH Factor..........................................7.0 to 7.5
OPERATION
!
CAUTION
HOT STEAM WILL ESCAPE WHEN DOOR IS BEING OPENED. TO PREVENT BURNS KEEP
HANDS AND FACE AWAY FROM STEAM.
If “SERVICE REQUEST” light illuminates during operation, contact your authorized service agency
immediately.
1. Suggested cooking times for various foods are shown in the table in the following section.
2. Pan specifications are shown on specifications page (page 4).
3. The door may be opened or closed at any time.
4. Timer can be used as desired, but it has no effect on the operation of the unit!
5. Unit will automatically idle at operating temperature when and if the door is closed and there is no food
in the cavity.
SHUTDOWN
1. Turn lever to the “OFF” position.
2. Remove pan guides.
3. Clean all interior surfaces with soap, water, and a non-metallic pad. Occasional use of a deliming
solution such as Lime-A-Way is recommended. RINSE THOROUGHLY WITH CLEAN WATER.
4. Ensure drain opening is clear.
5. Clean drain cover.
6. Replace pan guides.
7. Leave the door open at night after cleaning to prolong the life of the gasket.
NOTICE
DO NOT USE high-chlorine or bleach solution for cleaning the door gasket.
DO NOT USE steel wool or other metallic pads in the steamer.
PAGE 12
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
COOKING HINTS
COOKING HINTS
COOKING TIPS
Schedule cooking of fresh vegetables so that they will be served soon after they are cooked. If it is
necessary to prepare them in advance, they can be plunged into cold water, drained thoroughly and held
under refrigeration until needed for service.
Five pounds of cold cooked vegetables can be reheated in the steamer in 5 to 10 minutes, depending upon
the variety.
SUGGESTED COOKING TIMES
Timer settings are for general guidance only. Differences in food quality, size, shape, freshness, load size,
and desired degree of doneness must be taken into consideration and adjustments made in time, if
necessary.
Cooking Time
Product
Weight
Portions
(minutes)
Pan Used
Asparagus
Fresh
3½ lbs.
5 lbs.
14 (4 oz.)
20 (4 oz.)
8-10
9
Full/Perforated
Full/Perforated
Frozen Spears (Thawed)
Beans
Green - Frozen, Cut
Green - Fresh
Wax - Frozen
Lima - Frozen
5 lbs.
5 lbs.
5 lbs.
5 lbs.
20 (4 oz.)
20 (4 oz.)
20 (4 oz.)
20 (4 oz.)
12
15-17
13
Full/Perforated
Full/Perforated
Full/Perforated
Full/Perforated
10
Broccoli
Spears -Fresh
Spears - Frozen (Thawed)
4 lbs.
5 lbs.
16 (4 oz.)
20 (4 oz.)
10-12
8
Full/Perforated
Full/Perforated
Brussel Sprouts
Fresh
Fresh
5 lbs.
5 lbs.
20 (4 oz.)
20 (4 oz.)
15-17
13
Full/Perforated
Full/Perforated
Carrots
Frozen - Whole Baby
Fresh - ¼-inch Bias Cut
5 lbs.
5 lbs.
20 (4 oz.)
20 (4 oz.)
12
12
Full/Perforated
Full/Perforated
Cabbage
Green, Cut Into Wedges
Red, Cut Into Wedges
24
16
15
18-20
Full/Perforated
Full/Perforated
Cauliflower
Fresh, Whole
Fresh, Whole
Frozen, Flowerettes
2 lbs.
2 lbs. 12 oz.
5 lbs.
8 (4 oz.)
11 (4 oz.)
20 (4 oz.)
9-10
15
10-12
Full/Perforated
Full/Perforated
Full/Perforated
Corn
Fresh, Cob, 4-5 Inch Ears
Frozen - Whole Kernel
Frozen - Cob, 6 Inch Ears
5½ lbs.
5 lbs.
9 lbs.
15
20 (4 oz.)
14
13-15
8
12-14
Full/Perforated
Full/Perforated
Full/Perforated
Table continues on next page.
OPERATOR’S MANUAL 1183437
PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
COOKING HINTS
SEZ SERIES COUNTERTOP STEAMERS
Table continuing from previous page.
Cooking Time
Product
Weight
5 lbs.
Portions
20 (4 oz.)
20 (4 oz.)
(minutes)
Pan Used
Mixed Vegetables
Frozen
12
8
Full/Perforated
Full/Perforated
Peas
Frozen
5 lbs.
Potatoes
Red Bliss - Whole
Russetts - Whole
Russetts - Peeled
Russetts 1-Inch Cubes
7 lbs.
8 lbs.
5 lbs.
5 lbs.
28
20
12
35
25-35
20
Full/Perforated
Full/Perforated
Full/Perforated
Full/Perforated
20 (4 oz.)
17
Spinach
Fresh, Leaf
Frozen, Chopped
2½ lbs.
6 lbs.
10 (4 oz.)
24 (4 oz.)
5
35
Full/Perforated
Full/Perforated
Zucchini
Fresh - Slices ¼-inch Thick
5 lbs.
20 (4 oz.)
6-8
Full/Perforated
Broccoli
Spears -Fresh
Spears - Frozen (Thawed)
4 lbs.
5 lbs.
16 (4 oz.)
20 (4 oz.)
10-12
8
Full/Perforated
Full/Perforated
Eggs
Large - Hard Cooked
12 lbs.
12
15-16
½ Perforated
Meats
Corned Beef
Hot Dogs, Thawed
Hot Dogs, Frozen
6¾ lbs.
5 lbs.
5 lbs.
18 (6 oz.)
40 (2 oz.)
40 (2 oz.)
2 hours
5
10
Full
Full/Perforated
Full/Perforated
Fowl
Boneless Chicken Breast
4½ lbs.
12 (6 oz.)
15
Full/Perforated
Tamales, Frozen
Tortilla, Frozen 8-Inch
3 lbs.
4 Tortillas
12 (4 oz.)
4
20
Full/Perforated
Half/Perforated
45 Seconds
Beef Ravioli, Frozen
Elbow Macaroni
Spaghetti
48 Ravioli
(1 lb. 8 oz.)
8
5-6
Full/Perforated
2 lbs.
Uncooked
32 (2 oz.)
32 (2 oz.)
32 (2 oz.)
7
In Perforated Pan
Nested in Solid Pan
2 lbs.
Uncooked
14
10
25
In 4-Inch
Full/Perforated
Egg Noodles
2 lbs.
Uncooked
Full/Perforated
Converted Rice
2 lbs.
Full/Perforated
2½ Qts. Water
+ Oil & Salt
Navy Beans
2 lbs.
Full/Perforated
Place beans in pan and cover with 3-quarts hot tap
water. Steam for 2 minutes; remove from steamer
and cover for 1 hour. Remove cover and place back
in steamer for 40 minutes.
Table continues on next page.
PAGE 14
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
COOKING HINTS
Table continuing from previous page.
Cooking Time
Product
Weight
Portions
(minutes)
Pan Used
Black Eyed Peas
2 lbs.
Full/Perforated
Place beans in pan and cover with 3-quarts hot tap
water. Steam for 2 minutes; remove from steamer
and cover for 1 hour. Remove cover and place back
in steamer for 35 minutes.
Oysters
5 lbs.
16 Count
12
Perforated Pan
Nested in Full Pan
2½-Inch Deep
Shrimp, Fresh, Medium, Heads Removed
Shrimp, Frozen, Large, Peeled & Deveined
Lobster
5 lbs.
5 lbs.
6-7
8
Full/Perforated
Full/Perforated
Full/Perforated
Full/Perforated
Full/Perforated
1¾ lbs.
1 lb.
8
Alaskan King Crab Legs
Cherrystone Clams
4-5
7
5 lbs.
12
Fish Fillets
7½ lbs.
12 (10 oz.)
18
Full/Perforated
Nested in Full
Hotel Pan
•
•
•
For eggs cooked in the shell, adding salt to the cooking water increases cooking efficiency and decreases cooking
time. If the egg cracks, the white is cooked at the crack and is sealed right away.
To avoid green yolk (which is a deposit of iron sulfide) chill the eggs immediately after removing from the steamer by
plunging them into a cold water bath (preferably containing ice).
A quick and easy way to cook eggs for a salad mixture is to crack them directly into a solid steam table pan which has
been lightly coated with salad oil. Do not mix. Steam until they are hard cooked. Remove and chop as you would for
egg salad. The job of peeling is eliminated.
•
•
Transfer steamed hot chicken to deep pan, cover with Cacciatore Sauce and finish in oven. Bake 20 to 30 minutes.
May be held on steam table.
Chicken, sausage, and/or fish may be browned in Infra-Red or Radiant Broiler after steaming by brushing with melted
margarine mixed with salad oil to give a golden brown color.
•
•
Save juices from steamed chicken or turkey to make soups, sauces, or casserole dishes.
Chicken may be steamed in advance and refrigerated for next day’s use. Be sure to bring product back to 180°F
before serving.
•
•
•
•
•
•
•
Save the juice from the corned beef. After the cabbage has been steamed, place it in a solid pan and add the juice
for flavoring and holding on a steam table.
Steaming brisket is a definite time saver. Boiling in water takes 40 to 50 minutes per pound. Using the steamer can
save 50% in cooking time.
Cabbage, when steamed, retains its color and wedge identity. It will not break apart as it does when boiled in an
open pot.
When removing items prepared in a perforated pan, place a solid pan underneath the perforated pan with the cooked
food in order to prevent dripping on the floor.
The steamer is designed to accept standard 12" x 20" pans. Fractional size pans and dishes can be used as well
with the optional perforated shelf.
For stirring, the pan does not have to be removed from the steamer. Pull pan 1/3 way out of the cavity and the entire
surface is accessible.
The door may be opened at any time during operation to remove or add food.
OPERATOR’S MANUAL 1183437
PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING
SEZ SERIES COUNTERTOP STEAMERS
CLEANING
Southbend equipment is constructed with the best quality materials and is designed to provide durable
service when properly maintained. To expect the best performance, your equipment must be maintained in
good condition and cleaned daily. Naturally, the frequency and extent of cleaning depends on the amount
and degree of usage.
Following daily and more extensive periodic maintenance procedures will increase the life of your equipment.
Climatic conditions (i.e., salt air, seasonings, and water quality) may result in the need for more thorough and
more frequent cleaning in order to keep equipment performing at optimal levels.
! WARNING: BURN HAZARD
For proper and safe operation, this steamer must be cleaned daily as described in this manual.
Failure to do so could result in serious injury or damage.
Drains must be kept clean and clear of debris.
! WARNING: SHOCK HAZARD
DO NOT GET WATER IN THE CONTROLS.
This could result in expensive repairs and/or electrical shock.
De-energize all power to equipment before cleaning the equipment.
DAILY CLEANING
1. Turn lever to the “OFF” position.
2. Remove pan guides.
3. Clean all interior surfaces with soap, water, and a non-metallic pad. Occasional use of a deliming
solution such as Lime-A-Way is recommended. RINSE THOROUGHLY WITH CLEAN WATER.
4. Ensure drain opening is clear.
5. Clean drain cover.
6. Replace pan guides.
7. Leave the door open at night after cleaning to prolong the life of the gasket.
NOTICE
DO NOT USE high-chlorine or bleach solution for cleaning the door gasket.
DO NOT USE steel wool or other metallic pads in the steamer.
PERIODIC CLEANING
•
If lime or mineral deposits start to build up in the interior, clean the unit by using Southbend “descaler” or
other non-caustic deliming solution. Follow manufacturer’s recommended procedures. Thoroughly rinse
out unit with clean water.
•
To remove normal dirt, grease, or product residue from stainless steel, use ordinary soap and water
applied with a sponge or cloth. Dry thoroughly with a clean cloth. Never use vinegar or any corrosive
cleaner.
PAGE 16
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
CLEANING
•
To remove grease and food splatter or condensed vapors that have baked on the equipment, apply
cleanser to a damp cloth or sponge and rub cleanser on the metal in the direction of the polishing lines
on the metal. Rubbing cleanser as gently as possible in the direction of the polished lines will not mar
the finish of the stainless steel. NEVER RUB WITH A CIRCULAR MOTION. Soil and burnt deposits
which do not respond to the above procedure can usually be removed by rubbing the surface with
SCOTCH-BRITE scouring pads. DO NOT USE ORDINARY STEEL WOOL, as any particles left on the
surface will rust and further spoil the appearance of the finish. NEVER USE A WIRE BRUSH, STEEL
SCOURING PAD, SCRAPER, FILE OR OTHER STEEL TOOLS. Surfaces which are marred collect dirt
more rapidly and become more difficult to clean. Marring also increases the possibility of corrosive
attack. Refinishing may then be required.
SEMIANNUAL CLEANING
At least twice a year, have your Southbend Authorized Service Agency or another qualified service
technician clean and adjust the unit for maximum performance. Semiannual cleaning should include the
following:
1. Add two gallons of deliming solution through the door into the cavity.
2. Turn unit on, let run for 30 minutes.
3. Turn unit off and drain all solution from the cavity.
4. Fill unit with clean water and drain. Repeat 2 times.
Consult the Southbend Authorized Parts/Service Distributor list for the Authorized Service Representative in
your area or contact Southbend at 1-800-348-2558 for this information.
OPERATOR’S MANUAL 1183437
PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
SEZ SERIES COUNTERTOP STEAMERS
TROUBLESHOOTING
This section contains a troubleshooting key and referenced flowcharts to assist a qualified service technician
in the servicing of an SEZ Series Countertop Steamer. Please note that the unit has a “SERVICE
REQUEST” light that illuminates in the event of certain water supply problems. Also note that when
the unit is turned on, there is a four-minute time delay before the heating elements come on to allow
time for filling. Therefore, some procedures call for a waiting period when reconnecting power to the
unit or turning the unit on.
TROUBLESHOOTING KEY
Find the symptom below that corresponds to the malfunction, then turn to the corresponding figure and page.
Follow the flowchart on that page until the problem is solved.
Symptom
Page
Unit Not Heating Up, “ON” Light Not Lit
19
20
21
22
23
Unit Not Heating Up Properly or Not Cooking Properly, “ON” Light Lit
Excessive Steam Coming from Pressure Relief Vent
“Service Request” Light Comes On During Operation
Buzzer Does Not Come On
TROUBLESHOOTING FIGURES AND PROCEDURES
Figure and/or Procedure
Page
Voltage Check at Control Panel Fuse Block
Heating Element Resistance Check (at Contactor)
Main Fuse Replacement
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
Power Switch Continuity Check
Contactor and MOV Check
Timer and Buzzer Check
Door Switch Continuity Check
Float Switch Continuity Check
Controller Check
Water Solenoid Check
Pressure Switch Check
High-Limit Thermostats Check
Electric Schematic for 208, 220, and 240 Volt Model SEZ/3
Electric Schematic for 480 Volt Model SEZ/3
Electric Schematic for 208, 220, and 240 Volt Model SEZ/5
Electric Schematic for 480 Volt Model SEZ/5
PAGE 18
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
TROUBLESHOOTING
Unit Not Heating Up, “ON” Light Not Lit
Unit not heating up, “ON” light not lit.
Check that circuit breaker is ON and that proper voltage
is available at main fuse block.
DISCONNECT POWER AT CIRCUIT BREAKER.
Remove control panel without disconnecting plug.
Reconnect power.
Turn lever to “ON” position. Actuate door switch.
Check voltage between A and B on control panel fuse
block (see Figure 7 on page 24).
Does voltage
match serial plate
voltage?
No
Yes
Check voltage on side C and D on control panel
fuse block (see Figure 7 on page 24).
DISCONNECT POWER AT CIRCUIT BREAKER.
Check resistance between contactor terminals
(see Figure 8 on page 25).
Does voltage
match serial plate
voltage?
Yes
No
Is
measured resistance
consistent with the table
in Figure 8 on
No
Yes
page 25)?
Check voltage across
terminals 1 and 2 of
terminal block (see
Figure 7 on page 24).
Check for short circuit in
power switch (see
Figure 10 on page 27),
contactor and MOV
(see Figure 11 on page
28), and buzzer (see
Figure 12 on page 29).
Replace as necessary.
Replace elements
and main fuses
(see Figure 9 on page
26).
Check main fuses and
replace as needed
(see Figure 9 on page
26).
Replace control panel
fuses.
Does voltage
match serial plate
voltage?
No
Yes
Test power switch or adjust so
that it is actuated properly by
cam on valve shaft. Replace
switch as necessary
Replace “ON” light;
continue on next page.
(see Figure 10 on page 27).
OPERATOR’S MANUAL 1183437
PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
SEZ SERIES COUNTERTOP STEAMERS
Unit Not Heating Up Properly or Not Cooking Properly, “ON” Light Lit
Unit not heating up properly or not cooking properly, “ON” light lit.
DISCONNECT POWER AT THE CIRCUIT BREAKER.
Check all three main fuses; replace as necessary (see Figure 9 on page 26).
Reconnect power to unit.
Turn unit on. WAIT 5 MINUTES.
Open door; depress and hold door switch.
Does contactor
“click” on and stay on
Yes
No
for at least 2
minutes?
DISCONNECT POWER AT CIRCUIT BREAKER.
DISCONNECT POWER AT CIRCUIT BREAKER.
Remove control panel.
Remove control panel.
Check resistance between contactor terminals and
replace elements as necessary (see Figure 8 on
page 25).
Check door switch for continuity (see Figure 13 on
page 30).
Continuity?
No
Yes
Replace door switch.
Reconnect door switch
lead wires.
Remove rear cover.
Check pressure switch for
proper operation (see
Figure 17 on page 34).
Check high-limit
thermostats (see
No
Pressure switch OK?
Yes
Figure 18 on page 35).
High-limit
thermostats
OK?
No
Yes
Replace pressure switch.
Replace high-limit
thermostats
as necessary.
Check and replace
contactor (see Figure 11
on page 28) and/or
controller (see Figure 15
on page 32),
as necessary.
PAGE 20
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
TROUBLESHOOTING
Excessive Steam Coming from Pressure Relief Vent
Excessive steam coming from pressure relief vent.
DISCONNECT POWER AT CIRCUIT BREAKER.
Check pressure switch for proper operation (see Figure 17 on page 34).
Yes
Pressure switch OK?
No
Remove control panel, but leave plug connected.
Check controller (see Figure 15 on page 32).
Replace pressure switch.
Controller OK?
Yes
No
Check contactor and
replace as necessary
(see Figure 11 on page
28).
Replace controller.
OPERATOR’S MANUAL 1183437
PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
SEZ SERIES COUNTERTOP STEAMERS
“Service Request” Light Comes On During Operation
“Service Request” light comes on during operation.
Turn unit off and check that unit drains fully.
Open door. Turn unit back on and wait 20 minutes.
Is water level
at normal level
in cavity?
Yes
No
Check for adequate water pressure to unit.
DISCONNECT POWER AT CIRCUIT BREAKER.
Check controller (see Figure 15 on page 32).
DISCONNECT POWER AT CIRCUIT BREAKER.
Check high-limit thermostats
(see Figure 18 on page 35).
High-limit
thermostats
OK?
Yes
No
Controller OK?
Yes
No
Replace high-limit
thermostats
as necessary.
Replace controller.
Check water solenoid (see Figure 16 on page 33).
Check controller (see Figure 15 on page 32) and
replace as necessary.
Water solenoid OK?
No
Yes
Replace
water solenoid.
Remove screen from strainer and clean or replace
as necessary. Reassemble, reconnect, and recheck
the steamer. If the Service Request light still comes
on, examine the following for obstructions or
deposits: pressure regulator, solenoid, and check
valve. Clean or replace as necessary.
PAGE 22
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
TROUBLESHOOTING
Buzzer Does Not Come On
Buzzer does not come on.
DISCONNECT POWER AT CIRCUIT BREAKER.
Remove control panel.
Set timer for five minutes.
Does timer
time down?
Yes
No
Remove buzzer lead wires from timer.
Check timer (see Figure 12 on page 29).
Replace timer.
Continuity?
Yes
No
Replace buzzer.
Replace timer (see
Figure 12 on page 29).
OPERATOR’S MANUAL 1183437
PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
SEZ SERIES COUNTERTOP STEAMERS
Figure 7
Voltage Check at Control Panel Fuse Block
Control Panel
Fuse Block
Door Switch
Terminal
Block
Power Switch
“ON” Light
“SERVICE REQUEST”
Light
1. DISCONNECT POWER AT CIRCUIT BREAKER.
2. Remove control panel without disconnecting plug.
3. Turn lever to “ON” position.
4. Reconnect power.
5. Place leads as shown for test being performed.
6. Check that the voltage is in the range 200 to 240 volts.
PAGE 24
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
TROUBLESHOOTING
Figure 8
Heating Element Resistance Check (at Contactor)
C
B
A
Contactor
(top view)
1. DISCONNECT POWER AT CIRCUIT BREAKER.
2. Remove control panel.
3. DO NOT REMOVE HEATING ELEMENT LEAD WIRES FOR THIS TEST.
4. Place test leads between terminals A and C on left side of contactor.
5. Check the resistance and compare to the allowable range in the following table:
Model SEZ/3
Model SEZ/5
Allowable Resistance (Ohms)
Allowable Resistance (Ohms)
Voltage
Three-Phase
A-B or B-C
Single-Phase
Three-Phase
A-B or B-C
Single-Phase
A-C
A-C
5 to 6
A-C
A-C
4 to 5
208
220
240
480
10 to 12
12 to 13
14 to 16
55 to 64
14 to 16
15 to 18
18 to 21
73 to 85
8 to 10
9 to 11
11 to 13
13 to 15
15 to 17
60 to 70
6 to 7
5 to 6
7 to 9
11 to 13
45 to 52
6 to 7
29 to 34
24 to 28
6. For three-phase units, check resistance between terminals A and B and between terminals B and
C similarly.
OPERATOR’S MANUAL 1183437
PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Figure 9
SEZ SERIES COUNTERTOP STEAMERS
Main Fuse Replacement
Shown with Rear Cover Removed
Water Inlet Connection
Drain Connection
Main Fuse Block
3/4" Conduit Fitting Hole
1. DISCONNECT POWER AT CIRCUIT BREAKER.
2. Remove rear cover from unit.
3. Check fuses for continuity.
4. Replace as necessary.
PAGE 26
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
TROUBLESHOOTING
Figure 10
Power Switch Continuity Check
Control Panel
Fuse Block
Power Switch
“ON” Light
1. DISCONNECT POWER AT CIRCUIT BREAKER.
2. Remove control panel.
3. Turn Lever to “ON” from “OFF” and to “OFF” from “ON” ensuring that the power switch is properly
actuated.
4. Remove power switch lead wires from fuse block and terminal strip (note wire locations).
5. Place test leads on “C” and “NO” lead wires as shown.
6. Check for continuity with lever in “OFF” position (there should be no continuity).
7. Check for continuity with lever in “ON” position (there should be continuity).
8. Repeat steps 5 through 7 with test leads between other pair of “C” and “NO” lead wires.
9. Place test lead on “NO” lead wire and other test lead on other “NO” lead wire.
10. Check for continuity with lever in “ON” position (there should be no continuity).
11. Reconnect wires or replace switch as necessary.
OPERATOR’S MANUAL 1183437
PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
SEZ SERIES COUNTERTOP STEAMERS
Figure 11
Contactor and MOV Check
Actuator
C
B
A
F
E
D
MOV
TOP VIEW
LEFT SIDE VIEW
1. DISCONNECT POWER AT CIRCUIT BREAKER.
2. Remove control panel and disconnect twelve-pin plug PL1.
3. Depress actuator on top of contactor. Actuator should travel freely and spring back when released.
4. Check for continuity between contacts A and D as shown in top view. There should be no
continuity.
5. Repeat Step 4 for contacts B and E and for contacts C and F.
6. Remove wire C16 from contactor coil.
7. Place test leads on contactor coil terminal as shown in left side view.
8. Check resistance.
9. If resistance is not in the range 350 to 425 ohms, remove MOV and recheck coil resistance.
If resistance is now in the range 350 to 425 ohms, replace MOV, otherwise replace contactor.
10. Reconnect all wires.
PAGE 28
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
TROUBLESHOOTING
Figure 12
Timer and Buzzer Check
Buzzer
Timer
1. DISCONNECT POWER AT CIRCUIT BREAKER.
2. Remove control panel.
3. Set timer for one minute and allow to time out. If timer does not run, then replace.
4. Remove buzzer lead wires from timer and terminal block position 2.
5. Place test leads between positions 1 and 3 on the timer.
6. Check for continuity. If no continuity, replace timer.
7. Place test leads in terminals of buzzer lead wires.
8. Check that resistance is approximately 3.4 Kohms. Otherwise, replace buzzer.
OPERATOR’S MANUAL 1183437
PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
SEZ SERIES COUNTERTOP STEAMERS
Figure 13
Door Switch Continuity Check
1. DISCONNECT POWER AT CIRCUIT BREAKER.
2. Remove control panel.
3. Depress and release door switch actuator rod to make sure door switch is properly actuated.
4. Remove door switch lead wires from terminal block position 1 and terminal 5 of the controller.
5. Place test leads as shown inside the terminal connectors of the lead wires.
6. Check for continuity - (there should be NO continuity).
7. Depress door switch actuator rod and check for continuity - (there should be continuity).
8. Replace as necessary.
PAGE 30
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
TROUBLESHOOTING
Figure 14
Float Switch Continuity Check
Float Control Box
Float Switch
Float Switch Fitting
1. DISCONNECT POWER AT CIRCUIT BREAKER.
2. Remove rear cover from unit.
3. Disconnect float switch lead wires from wire B41 and the pressure switch C terminal.
4. Remove float from bottom of float control box.
5. Make sure float travels freely along stem of float switch.
6. Place test leads in float switch terminals as shown.
7. Hold float in same orientation as when installed (float at bottom of stem).
8. Check continuity. There should be continuity. Replace as necessary.
9. Lift float to the top of the stem.
10. Check for continuity. There should be no continuity. Replace as necessary.
OPERATOR’S MANUAL 1183437
PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
SEZ SERIES COUNTERTOP STEAMERS
Figure 15
Controller Check
1. DISCONNECT POWER AT CIRCUIT BREAKER.
2. Remove control panel, but leave plugged in.
3. Disconnect wires from positions 2, 3, 4, 7, 8, and 9 on controller. Cover the ends of the wires
with electrical tape to prevent contact with metal or skin.
4. Use jumper wires to connect together positions 3, 4, and 5 on controller.
5. Reconnect power to unit and turn unit on. Wait six minutes.
6. Test for 200 to 240 volts between positions 12 and 13 on controller. If no voltage is present, see
page 19.
7. Use a spacer to hold the door switch in the closed position.
8. Test for 200 to 240 volts between positions 13 and 5 on controller. If no voltage is present, check
door switch using the procedure on page 30.
9. Test for 200 to 240 volts between positions 7 and 13, and also between positions 8 and 13. If no
voltage is present, replace the controller.
10. Test that there is no voltage between positions 9 and 13. If voltage is present, replace controller.
11. Remove spacer from door switch so that the switch will be in the open position.
12. Test that there is no voltage between positions 7 and 13, and no voltage between positions 8 and
13. If voltage is present, replace the controller.
13. Test that there is no voltage between positions 9 and 13. If voltage is present, replace the
controller.
14. Disconnect power, add a jumper wire between positions 2 and 12 on the controller, then reconnect
the power. The unit should still be turned on. Wait six minutes.
15. Test that there is no voltage between positions 7 and 13. If voltage is present, replace controller.
16. Remove all jumpers, reconnect all wires, and re-test unit.
PAGE 32
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
TROUBLESHOOTING
Figure 16
Water Solenoid Check
1. DISCONNECT POWER AT CIRCUIT
BREAKER.
2. Remove rear cover.
3. Disconnect water solenoid lead wires from
wires B60 and B61.
4. Place test leads into water solenoid lead
wires as shown.
5. Resistance should be approximately 800
ohms. Replace if necessary.
6. Disconnect water inlet subassembly from
float control box at the compression fitting
closest to the box.
7. Apply of water pressure (approximately 15
psi) to water inlet. Water should not leak out
of the compression fitting. If necessary,
replace solenoid.
8. Reassemble water inlet, reconnect solenoid
lead wires, and reconnect power to unit.
When power is turned on, the solenoid
should “click.” If no click is heard, test for 200
to 240 volts on wires B60 and B61 within four
minutes of turning on power switch. If 200 to
240 volts is present and the solenoid does
not click, replace solenoid.
OPERATOR’S MANUAL 1183437
PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
SEZ SERIES COUNTERTOP STEAMERS
Figure 17
Pressure Switch Check
SWITCH DETAIL
COM
NO
NC
Pressure Switch
Float Control Box
1. DISCONNECT POWER AT CIRCUIT BREAKER.
2. Remove rear cover.
3. Remove wires B40 and B42 from pressure switch “COM” and “NO” terminals.
4. Open door.
5. Place test leads on “COM” and “NO” terminals as shown.
6. Check continuity. There should NOT be continuity. Replace as necessary.
7. Remove pressure switch from lid.
8. With test leads on “COM” and “NO” terminals as before, gently blow into pressure port and check
continuity. There SHOULD be continuity. Replace as necessary.
PAGE 34
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
TROUBLESHOOTING
Figure 18
High-Limit Thermostats Check
1. Note: Allow cavity bottom to cool before performing this test.
2. Disconnect left thermostat lead wire from wire B62.
3. Disconnect center thermostat lead wire from wire B57.
4. Disconnect right thermostat lead wires from wires B58 and B59.
5. Disconnect remaining thermostat lead wires from each other.
6. Test each thermostat for continuity. Replace as necessary.
7. Reconnect all thermostat lead wires.
OPERATOR’S MANUAL 1183437
PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Figure 19
SEZ SERIES COUNTERTOP STEAMERS
Electric Schematic for 208, 220, and 240 Volt Model SEZ/3
PAGE 36
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
TROUBLESHOOTING
Figure 20
Electric Schematic for 480 Volt Model SEZ/3
OPERATOR’S MANUAL 1183437
PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Figure 21
SEZ SERIES COUNTERTOP STEAMERS
Electric Schematic for 208, 220, and 240 Volt Model SEZ/5
PAGE 38
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
TROUBLESHOOTING
Figure 22
Electric Schematic for 480 Volt Model SEZ/5
OPERATOR’S MANUAL 1183437
PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS
SEZ SERIES COUNTERTOP STEAMERS
PARTS
NOTICE
INSTALLATION OF OTHER THAN GENUINE SOUTHBEND PARTS WILL VOID THE WARRANTY
ON THIS EQUIPMENT.
The serial plate with voltage, model, and serial information is located on the right side of the steamer cavity
on the upper rear corner. On single units a second tag is located on the face of the door which will show
only model and serial number. On tandem units, a second tag is on the right side of the right unit and the left
side of the left unit.
Replacement parts may be ordered either through a Southbend Authorized Parts Distributor or a Southbend
Authorized Service Agency.
When ordering parts, please supply the Model Number, Serial Number, Part Number, Description, Finish,
and Electrical Characteristics as applicable.
For parts not listed, consult a Southbend Authorized Parts Distributor or Southbend Authorized Service
Agency. Consult the Southbend Authorized Parts/Service Distributor list for the Authorized Parts supplier in
your area. If this list is not available, call Southbend at 1-800-348-2558 to obtain this list.
Index of Parts Diagrams
Page Number
Description
41
42
44
45
46
48
Cavity and Heater Parts
Control Panel Parts (Rear View)
Control Panel Parts (Front and Isometric Views)
Door Assembly Parts
Water Inlet and Drain Parts
Float Tank Parts
PAGE 40
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
PARTS
Cavity and Heater Parts
4
3
5
6
2
1
Part Number
Model SEZ/3 Model SEZ/5
Key
Qty Description
1
1181508
1181509
1181510
1181511
1181011
1181522
1181601
1178663
1178668
1181771
1181772
1181773
1181774
1181011
1181522
1181601
1178679
1178678
6
6
6
6
3
1
1
1
1
Heater, cartridge, 208V (1500W for SEZ/3, 1834W for SEZ/5)
Heater, cartridge, 220V (1500W for SEZ/3, 1834W for SEZ/5)
Heater, cartridge, 240V (1500W for SEZ/3, 1834W for SEZ/5)
Heater, cartridge, 480V (1500W for SEZ/3, 1834W for SEZ/5)
Thermostat, 200C, 600V
2
3
4
5
6
Plate, cavity vent
Retaining ring
Side, rack, right
Side, rack, left
OPERATOR’S MANUAL 1183437
PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS
SEZ SERIES COUNTERTOP STEAMERS
Control Panel Parts (Rear View)
See drawing on following page.
NOTE: The entire Control Panel Assembly can be ordered as part number 1181543.
Key Part Number Qty Description
1
2
1175712
1183420
1146320
1178331
1177396
1183430
1146398
1178391
1183423
1178535
1177865
1178549
1178276
1178329
1178330
1183426
1183425
1178341
6600430
1
1
6
1
2
4
3
1
1
1
1
1
1
1
1
1
1
1
1
Buzzer assembly
Controller
3
Screw, 6-32x1, round hd
Switch, door
4
5
Locknut, 6-32 ss
6
Screw, 10-32x1/4, ss, rnd, hd
Screw, 6-32x3/8, ss, phil pan hd
Fuseblock, control
Plate, control panel
Switch, power
7
8
9
10
11
12
13
14
15
16
17
18
19
Nut, hex, 5/8-18, brass
Screw, set
Cam actuator
Light, indicating, amber clip lens
Light, indicating, red clip lens
Terminal block
Gasket, control
Timer, mechanical
Locknut
PAGE 42
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
PARTS
Control Panel Parts (Rear View)
See parts list on previous page.
8
9
10
11
12
13
7
6
14
5
15
16
4
3
17
18
19
2
1
OPERATOR’S MANUAL 1183437
PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS
SEZ SERIES COUNTERTOP STEAMERS
Control Panel Parts (Front and Isometric Views)
6
5
4
7
8
3
2
1
9
10
11
NOTE: The entire Control Panel Assembly can be ordered as part number 1183428.
Key Part Number Qty Description
1
2
1178331
1178338
1179932
1178388
1177770
1181513
1181529
1170337
1178270
1178339
1178347
1
1
1
1
1
1
1
1
1
1
2
Switch, door
Retaining ring
3
Spring, retaining
Valve lever weld assembly
Valve lever bushing
Polypanel with timer
Panel, control, weld assembly
Knob
4
5
6
7
8
9
Switch, actuator rod
Washer
10
11
Seal, shaft
PAGE 44
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
PARTS
Door Assembly Parts
6
7
5
4
3
2
1
Part Number
Model SEZ/3 Model SEZ/5
Key
Qty Description
1
1177317
1177080
1178171
1178105
1178096
1178106
1173224
1178167
1177317
1177080
1181018
1181016
1181010
1181001
1173224
1181015
1
1
1
1
1
1
1
1
Latch assembly
Cast striker
2
3
Door insulation block
Panel assembly, inner door
Gasket, door
4
5
6
Gasket rtnr pnl
7
Screw, 1/2-20 x 5/8 s, slot trs
Complete door assembly
1-7
OPERATOR’S MANUAL 1183437
PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS
SEZ SERIES COUNTERTOP STEAMERS
Water Inlet and Drain Parts
See drawing on following page.
Key Part Number Qty Description
1
2
1181579
1181589
PP-285
1
1
1
1
1
1
3
1
1
1
1
2
1
1
1
1
2
1
1
Elbow 1/4CC x 1/4 MPT
Tube, water inlet
3
Fitting, 1/4 NPT male
Bracket, water train
Tee, 1/4NPT, fem
Pressure regulator
Nipple, hex 1/4 NPT
Strainer, Y in-line
Water inlet weld assembly
Gauge. pressure
Valve, solenoid
4
1183419
1181758
1180937
1183445
1173428
1181556
1181762
1181607
1161048
1181551
1181591
1181590
1180956
1181557
1181528
1181526
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Elbow, 1/4
Nipple, close
Hose, drain,1/2" I.D. nylon/braid
Fitting, 3/8 MPT x
Tee, 3/8 brass
Nipple, 3/8 NPT
Elbow, 3/8 NPT
Valve 3/8 drain
PAGE 46
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
PARTS
Water Inlet and Drain Parts
See parts list on previous page.
8
9
7
6
5
4
10
11
12
3
2
13
14
15
1
19
18
17
16
OPERATOR’S MANUAL 1183437
PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS
SEZ SERIES COUNTERTOP STEAMERS
Float Tank Parts
See drawing on following page.
Key Part Number Qty Description
1
2
1183413
1174924
1183402
1181775
PP-501
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Fitting, float
Float switch, water fill
Box, float control weld assembly
Nipple, 1/8 npt x 3.5, brass
Coupling, 1/8 npt, ss
Pressure switch
3
4
5
6
1181540
1181522
1178338
1183403
1183416
1181542
1181514
1181597
1181578
1178444
7
Plate, cavity vent
8
Retaining ring
9
Box top, float control, weld assembly
Gasket, float control
Steam trap kit
10
11
12
13
14
15
Rod, float actuator
Plug, pipe, brass
Coupling, 1/2-unc x 1/4npt fxf
Valve, 3/8 ball
PAGE 48
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
PARTS
Float Tank Parts
See parts list on previous page.
8
7
6
5
9
4
10
11
12
3
2
1
13
15
14
OPERATOR’S MANUAL 1183437
PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
Notes:
PAGE 50
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
Notes:
OPERATOR’S MANUAL 1183437
PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
SEZ SERIES COUNTERTOP STEAMERS
SUPER SIMPLE STEAM
SEZ SERIES
COUNTERTOP STEAMERS
A product with the Southbend name incorporates the best in durability and low maintenance. We
all recognize, however, that replacement parts and occasional professional service may be
necessary to extend the useful life of this unit. When service is needed, contact a Southbend
Authorized Service Agency, or your dealer. To avoid confusion, always refer to the model number,
serial number, and type of your unit.
Southbend
1100 Old Honeycutt Road, Fuquay-Varina, NC 27526
(800) 348-2558 or (919) 552-9161 • FAX (800) 348-2558 or (919) 552-9798
PAGE 52
OPERATOR’S MANUAL 1183437
Download from Www.Somanuals.com. All Manuals Search And Download.
|