MODEL : STm.57b
MOBILE PRINTER
All specifications are subject to change without notice
Rev. 1.0
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Product overview
1. Unpacking
Standard
Front
Power switch
Printer
Battery
Belt Buckle
Paper feed
button
Cover open
button
Charger
Connector
Recharger
Serial Cable
USB Shelded Cable
Battery
Side
Roll paper
CD
Quick Manual
Optional
USB
shoulder strap
Battery Holder
(Cradle)
Cigar jack
Printer case
SERIAL
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Setting Up the Product
3-2. Installing battery
3-1. Control Panel Usage
Button
Name
function
Push the Open to the direction as
pointed by arrow in the image.
Open the battery cover and push up
the hook to the direction as above.
This button is used to turn the printer on and off.
Power
button
When the printer is off, press this button for approximately
2 seconds and it will turn on the power. When you press this button
in a state that the printer is on, the printer will turn off.
1
2
3
Paper output can be done manually by pressing this button.
Additionally, self-testing and Hexadecimal Dumping can be processed..
1. Refer to “3-10” for self test information.
Paper
Feed
Button
2. Refer to the service manual regarding Hexadecimal Dumping.
1. If the Batt, LED are Lit, the battery is fully charged.
2. If you can hear beeping sound and LED light is turned off, it means
that the battery is at the lowest level.
Battery
Status
Lamp
3. If the battery is not charged at all, the printer turns off automatically.
Error
If the red light is turned on, it means that the paper cover is open.
Lamp
Insert the battery inside printer as
shown.
Close the battery cover once you
inserted the battery completely.
NOTE
As the battery is not charged at the time of your purchase, charge the battery
prior to using the product.
(Use the battery charger and/or the optional battery holder.)
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3-3. Battery removel
3-4. Battery Charging
②
LED
①
Push the Open into the direction
Push up the hook after opening the
indicated with the arrow in the image. battery cover.
1. The battery can be charged only when the temperature is 0~40℃
2. Be sure that the printer is turn off and the battery to be charged is installed.
3. Connect the charger to the printer.
1
2
3
4. Recharging will now be started.
3-4-1 The status of lamp in charging
Status
charging
Red
charging complete
Green
Charging Lamp
NOTE
1. Unless the exclusive charger is used provided by the manufacturer, the printer
can be damaged, and the manufacturer is not liable for the consequential damage.
2. Before removing the battery, make sure that power is turned off.
3. Printer does not work in the status of being connected with charger only.
4. The battery should be installed to operate printer.
5. While charging, do not turn on the power.
6. Do not operate the print while charging the battery.
7. Do not connect the charger while the printer is operated.
Pull out the battery as shown above.
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
3-5. Battery charger Usage
3-6 Usage of Cigar Jack Charger for charging
Optional
Optional
②
LED
Printer
①
1. Please press the battery into the holder until you can hear a snapping sound.
2. Insert DC JACK ① into the end completely as the direct shown above.
3. Plug the power code to electrical outlet.
4. While charging the battery, red light turns on.
Once the charge is completed, green light turns on.
Check the state of code connection when error occurs blinking on red light.
Battery holder
3-5-1 The status of lamp in charging
Status
charging
Red
charging complete
Green
Connect the car cigar JACK charger into the printer or battery holder.
Charging Lamp
Input
12 ~ 24V
Output
8.4V 0.8 ~ 1.2A
NOTE
In the case the battery is not fixed properly in the holder, the red lamp will be blinking,
NOTE
Use the Cigar Jack offered by the manufacturer
Then, extract and reinsert the battery.
.
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
3-7. Belt clip Usage
3-8. Roll Paper Installation
Insert the belt hook screw into the hole of the belt hook.
Open the paper cover pressing the open
button. Insert a sharp tool into the paper
guide hole and push it in the direction of
Put the paper in the right direction after
adjusting the paper guide matching the paper
width. (Remove the paper core when it is
used all)
arrow as shown above.
1
2
1
3
2
4
As shown above, fasten the screw with a screw driver.
Pull out a short length of the paper and
shut the paper cover.
Press the Feed Key once to arrange
the paper.
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
3-9. Leather Case Usage
3-10. Shoulder Strap Usage
Optional
Optional
Put the printer into the leather case
following the direction shown in the
image.
Open the Velcro
Place the end of strap into the hook of
shoulder strap.
Insert the strap into the hook on
the printer.
1
3
2
4
1
2
3
Close the Velcro
Fasten the strap in the opposite
side with the sample way.
After pulling out the end of strap
tightly, put it into the clip to be
fastened.
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
3-11. Self Test
The sample of self test printout
Turn off the power pressing the
power button for approximately
3 seconds.
While you are pressing the FEED
button, press the power button
1
3
2
NOTE
1. To print ASCII pattern additionally,
press the Feed button once more
2. After printing ASCII pattern, the
self test will be finished automatically.
3. If the Feed button is not pressed
to print ASCII pattern, self test will be
finished automatically after 30 seconds.
The printout is produced.
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Peripherals Connection
This product can communicate with other devices via Bluetooth
communication and cable.
When the printer is installed initially or when you face a problem, you can run the
self test and check the information about
4-1. Bluetooth Connection
-Control Circuit, Mechanism, Print Quality, ROM Version
After checking with self-test and no issues are found, you can examine other
devices and software. This function is working independent of devices and software.
●
Motor protection from being overheated
The motor should be stopped and cooled about more than 30 seconds after
continuous printing 1.5 meter
1. The Printer can be connected to devices equipped with Bluetooth communication
capacity (PDAs, PCs, etc.)
2. Use the Bluetooth connection function supported by the device to connect
to the printer.
NOTE
Refer to the Bluetooth Manual for more details on connection.
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
|