Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Class D Topology IR2110S
S/N 87dB at 15kW @ 1 ohm
All "N" Channel MOSFET TO218 Transistors
Unregulated Power Supply
140 Volt Rails +/- for INSANE Amounts of Power
Capacitance Voltage 160V
Monster Solid Copper Buss Bars to Pass >1000 Amps of Current
Idle Current Draw 8 amps
Maximum Current Draw >1400 amps
Dual Monoblock Internally Bridged
Digitally Controlled Module for Damping Factor >1000 @ 100Hz
200mV - 7.6V Input Sensitivity
Short Circuit Speaker Protection
Thermal Protection
Optimized for a 16 Volt DC Power Supply
Totally Separated PWM Circuit to Eliminate Noise
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Unique Protection Sensing Circuit for Maximum Power
2.5mm Thick PCB (57% thicker than normal 1.6mm)
Over 83 Pounds!
Comes with Plexiglass & Metal Bottoms
Remote Bass Control Included
12 5/8" W x 2 3/4" T x 32 11/16" L
Subsonic Filter 15-50Hz @ 24dB Per Octave
Low-Pass X-over 40-275Hz @ 24dB Per Octave
Bass Boost 40-120Hz, 0-18dB
(4) 1/0 Gauge Power Input Terminals
(4) 1/0 Gauge Ground Input Terminals
(2) 8 Gauge Remote Turn-On Terminals
(4) 8 Gauge Speaker Output Terminals
Power at 16 Volts
Load
THD 1% THD 5% THD 10%
1 ohm each ch 4.55 kW 5.125 kW
6 kW
5 ohm each ch 7.34 kW
8.2 kW
10.4 kW
16.4 kW
9.31 kW
12.2 kW
19 kW
2 ohm Bridged
1 ohm Bridged
8.88 kW
14.4 kW
The XXX-15000D performs best with a 16 volt power source.
Soundstream recommends using a minimum 14.4 power source.
Power at 14.4 Volts
Load
THD 1% THD 5% THD 10%
1 ohm each ch
5 ohm each ch
2 ohm Bridged
1 ohm Bridged
4.1 kW
6.63 kW
8 kW
4.616 kW 5.4 kW
7.4 kW
9.36 kW
14.8 kW
8.379 kW
11 kW
13 kW
17.1 kW
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BRIDGED
+
+
+
+
INPUT
REMOTE
L
R
BASS
GAIN SUBSONIC BOOST
POWER
BASS EQ
LPF
[
]
GREEN
PROTECT
SPEAKER OUTPUT
[
]
SPEAKER OUTPUT
RED
MIN MAX
10Hz 50Hz
0dB 18dB
40Hz 120Hz 35Hz 250Hz
GND
GND
+12V
+12V
REM
+12V
+12V
GND
GND
POWER INPUT
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1.Input RCA jacks
INPUT
L
R
These inputs are for signal cables from the source. Always use high quality RCA cables.
2.Gain
GAIN
This control allows you to vary the amplifiers input sensitivity between 0.2[200millivolts]and 7.6volts.
Clockwise rotation raises the threshold and lowers the sensitivity, requiring higher input signal voltage
from the source. in order to obtain maximum output. counter-clockwise adjustment lowers the threshold
and raises the sensitivity, requiring a lower source voltage from source unit. The overall objective is to set
this control to closely match the voltage produced by the source unit.
Avoid setting the theshold too low and supplying excessive input signal voltage, as this would saturate
the input stages and introduce unwanted distortion.
3.Subsonic
10
50
Variable Subsonic Filter[10Hz - 50Hz]
The Subsonic filter will roll off all the unwanted frequencies below 10Hz - 50Hz.
This will allow the amplifier to use that wasted power in the audible bandwidth.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Bass Boost & EQ Control
40Hz
120Hz
The Bass EQ control is used to select the boost frequency. Any frequency from 40 to 120 Hz can be
selected. The Bass Boost control will increase the frequency selected from the Bass EQ up to 18dB.
5.LPF Control
LPF
35Hz 250Hz
This control is used to set desired low pass frequency[35 ~ 250Hz]
The filter acts to cut-off frequencies above the set-point.
6.Remote Control input
The Remote input can be connected to the Remote Dash Control with the supplied connection cable.
This control can be used to adjust the amplifier's input sensitivity.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
7. LED indicatior
POWER
[
]
GREEN
PROTECT
[
]
RED
POWER : This GREEN LED will illuminate when the amplifier is turned“ON”. If it fails to illuminate check
the power connections to the amplifier and fuses.
PROTECT : The amplifier protection circuitry will disable the amplifier if input overload, short circuit or
extremely high temperature conditions are detected. when the protection mode is in operation
the red LED indicator on the side panel will be illuminated the amplifier has gone into a self-preservation
mode.
If you observe that the protection LED is lit, please check the system carefully to determine what has
caused the protection circuit to engage. the amplifier can be reset by turning the remote power off
and then on again. If the amplifier shut down due to a thermal overload condition. please allow it to
cool down before restarting. If the amplifier shut down of an input overload or short circuit .be sure
to repair these conditions before attempting to power up the amplifier again.
8.Gnd[Chassis ground)
GND
GND
To avoid unwanted ignition noise caused by ground loops. It is essential that the amplifier be grounded
to a clean, bare, metal surface of the vehicles chassis.
It is not recommended to use seat or seat belt bolts..
8
Download from Www.Somanuals.com. All Manuals Search And Download.
9.Power[Battery positive]
+12V
+12V
Due to the power requirements of the amplifier this connection should be made directly to the positive
[+] terminal of battery. For safety measure install an in-line fuse Holder [not included] as close to the
battery positive [+] terminal as possible with an ampere rating not to exceed the maximum current
specified on page 3
10.
REM
To remote wire from source unit.
The amplifier is turned“ON” remotely when vehicle`s source unit is turned “ON”
9
Download from Www.Somanuals.com. All Manuals Search And Download.
BRIDGED
+
+
+
+
INPUT
REMOTE
L
R
BASS
GAIN SUBSONIC BOOST
POWER
BASS EQ
LPF
[
]
GREEN
PROTECT
SPEAKER OUTPUT
[
]
SPEAKER OUTPUT
RED
MIN MAX
10Hz 50Hz
0dB 18dB
40Hz 120Hz 35Hz 250Hz
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning on the Amplifier
The amplifier automatically turns on within a few seconds after remote voltage is applied. If your system is
set-up so that the source unit provides the remote voltage . Then it would turn on when your stereo is
turn on. Note that there are alternate means of providing the 12 volt remote control signal. including and
auxiliary switch.
Adjusting The Audio Level
As stated previously, it is important to obtain a close match between the source unit`s output voltage and
The amplifier`s sensitivity or admittance setting.
1. Use a screwdriver to turn the input sensitivity fully counter-clockwise to 200mV.
2. turn the auto sound system`s volume control to about one-third of its full range.
3. Adjust input sensitivity to a comfortable listening level.
4. turn up auto sound system`s volume control unit the sound begins to distort.
then immediately turn the volume down to a point just before where the distortion began.
Caution : Never turn up the auto sound system`s volume control more than needed to adjust
the audio level, more than two thirds of its maxinum volume.
5. Adjust the LPF to a desired setting. Raising the LPF will allow higher bass frequencies to play.
Lowering the LPF will block the higher bass frequencies.
6. Adjust the Sensitivity to closely match the output produced by the source unit,
or the maximum level the amplifier should play.
7. Set the Bass EQ to a desired frequency, and adjust the Bass Boost to a desired boost level.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|