Download from Www.Somanuals.com. All Manuals Search And Download.
FCC and IC Information:
Warnings: The device meets the exemption
from the routine evaluation limits in section 2.5
of RSS 102 and users can obtain Canadian
information on RF exposure and compliance
from the Canadian Representative Burnport
Holdings Ltd. 72MT Belcher Pls, East, Calgary,
Alberta,T2Z 2G1, CANADA. Tel: 403-257-4961
This device complies with Part 15 of the FCC
Rules and RSS-210 of the IC Rules. Operation is
subject to the following two conditions: (1) This
device may not cause harmful interference, and
(2) this device must accept any interference
received, including interference that may cause
undesired operation.
Warning: Changes or modifications to this unit
not expressly approved by the party responsible
for compliance could void the user's authority to
operate the equipment.
FCC&IC Radiation Exposure Statement
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment and meets the exemption from
the routine evaluation limits in section 2.5 of
RSS 102.
Note: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful interference
1. This Transmitter must not be co-located or
operating in conjunction with any other
antenna or transmitter.
2. This equipment complies with FCC RF
radiation exposure limits set forth for an
uncontrolled environment. This equipment
should be installed and operated with a
minimum distance of 20 centimeters from
user and bystanders.
in
a
residential installation. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
For compatibility between the SFQ-01 system
and another device with Bluetooth technology,
consult the device's documentation and dealer.
In some countries, there may be restrictions on
using Bluetooth devices. Check with your local
authorities.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Bluetooth is a registered trademark of Bluetooth
SIG, Inc
Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
Please read rating label at the bottom of system
for power input and other safety information.
Consult the dealer or an experienced radio TV
technician for help.
.2.
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION Proper Installation
Side View:
Install the system in a place which is level, dry
and neither too hot nor too cold.The appropriate
temperature is between 5 oC and 35 oC.
Install the system in a location with adequate
ventilation to prevent internal heat from
building up inside the unit.
15cm
(5-15
16")
/
Front side
Back side
15cm
(5-15
/16")
Leave sufficient distance between the system
and TV.
Keep the system away from TV to avoid
interference with TV.
(3-15
/16")
10 cm
CAUTION Proper Ventilation
QDID: B016948
To avoid risk of electric shock and fire, and to
prevent damage, locate the apparatus as
follows:
Front: No obstructions and open spacing.
Sides / Top / Back: No obstructions should be
placed in the areas shown by the dimensions
below.
Bottom: Place on the level surface. Maintain an
adequate air path for ventilation by placing on a
stand with a height of 10 cm (3-15/16") or more.
Front View:
15cm
(5-15
/16")
15cm
(5-15
16")
15cm
(5-15
16")
/
/
.3.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Getting Started
5
5
5
6
7
Package Contents
Installing/Replacing the Batteries
Connecting the AC Adapter
Using the Remote Control
8
8
8
9
System Overview
Front View
Back View
Remote Control
Selecting the Sound Source
9
10
10
10
11
Playing back from iPhone/iPod
Setting an iPhone/iPod on the Unit
Listening to an iPhone/iPod
Charging an iPhone/iPod
12
12
13
13
Playing back via Bluetooth/from iPad
Downloading the SoundFreaq App
Using multiple Bluetooth devices
Playing back from Macbook or Macbook Pro
14
Upgrading Wireless Connection Mode
Listening to Tuner
Listening to a Station
Presetting a Station
15
15
15
Playing back from External Source
Listening to the External Audio Device, Digital Music Player or
Any Other Audio Source
16
16
17
18
19
Activating "U-Cubed" Sound Effect
Troubleshooting
Technical Specifications
.4.
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Package Contents
Examine whether the following package contents are all included :
+
CR2025
3V
Lithium Coin Battery
CR2025
It is loaded on the remote
control at the factory.
Remote Control
Switch Power Adapter
Main Unit
Dock Adapters(2)
For iPhone 3G/3GS
and iPod Touch
Adapter Cable
FM Antenna
Installing/Replacing the Batteries
Handling the Remote Control
CAUTION: Danger of explosion if battery is
incorrectly replaced. Replace only with the
same or equivalent type.
To avoid possible failure, read the following
instructions and handle the remote control
properly.
1. Squeeze and pull to release the battery cover
latch. You can remove the battery door with
your fingernails by using the spaces set back
in wall.
Do not drop or cause impact to the remote
control.
Do not spill water or any liquid on the remote
control.
2. Match the polarity on the Lithium Cell with a
plus sign (+) on the battery tray.
Do not place the remote control on a wet
object.
Do not place the remote control under the
direct sunlight or near sources of excessive
heat.
P2ull
Squeeze
1
Note: If you are not going to use the remote
control for a long time, remove the battery to
avoid any damage that may be caused by
leakage and corrosion.
3. Slide the tray with new battery into the
battery compartment until you hear a click
sound.
+
CR2025
3V
.5.
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning - When Using the Battery
Store the battery in a place where children
cannot reach. If a child accidentally swallows
the battery, consult a doctor immediately.
Do not recharge, short circuit, disassemble,
heat the battery, or dispose the battery in
fire. Doing any of these things may cause the
battery to give off heat, crack, or start a fire.
Do not leave the battery with other metallic
materials. Doing this may cause the battery
to give off heat, crack, or start a fire.
Do not poke the battery with tweezers or
similar tools. Doing this may cause the
battery to give off heat, crack, or start a fire.
Dispose of battery in the proper manner,
according to federal, state, and local
regulations.
The batteries (battery pack or batteries
installed) shall not be exposed to excessive
heat source such as sunshine, fire or the like.
This product contains a CR Coin Cell Lithium
Battery that contains Perchlorate Material, so
that special handling may apply.
When throwing away or saving the battery,
wrap it in tape and insulate; otherwise, the
battery may start to give off heat, crack, or
start a fire.
Connecting the AC Adapter
1. Insert the switch power adapter into 18V DC
IN
WARNING! For optimal performance, use only
.
the supplied AC adapter.
2. Insert one end of the adapter cable into the
end of the switch power adapter and the
other end into an electrical outlet only after
all other connections are completed.
Ensure that power supply outlet matches with
the unit AC's input 100-240V~, 50/60Hz
before connection.
.6.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote Control
Using the remote control
Storing the remote control
remote control storage compartment is
Remove the insulation sheet before using for
the first time.
A
designed on the right side of system. The
remote control can be magnetized into the
compartment easily for your quick and
convenient use.
Aim the remote control at the IR Sensor on
the front lens within an approximate
distance of 7m (23 feet) away.
Push here.
IR Sensor
Remote control magnet
Open the door.
.7.
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
Front View
Back View
5
4
13
9
10
17
1
2
3
14
15 16
6
8
11 12
7
1. U-Cubed knob
Hold the button to fast-backward/fast-forward
a track.
Turn to activate or deactivate the U-Cubed
(High Definition Wide Stereo) sound effect.
Decrease/increase the frequency or select a
preset channel number (from 01 to 20) in
tuner mode.
2. Bass knob
Turn to adjust a desired bass effect ranged
from +3 to -3.
10.
11.
(Play/Pause) button
3. Treble knob
In iPhone/iPod and wireless audio modes,
press to play or pause a track.
Note: When the unit is building a wireless
audio connection with an iPad, this button
is disabled.
Turn to adjust a desired treble effect ranged
from +3 to -3.
4. 30-pin Apple connector
Connect with iPhone/iPod.
5. Pair indicator
Saves a radio channel in tuner mode.
(Power on/off) button
To indicate when building a wireless audio
connection.
Switch between standby and power-on
modes.
6. Source button
Select iPod, tuner, AUX or wireless audio
mode by pressing repeatedly.
7. Mute button
12. PAIR button
Build a wireless audio connection with an
external device.
Turn off the sound. Press again to restore the
sound output.
13. LCD display
14. DC IN jack
8. Vol +/- button
Connect the supplied switch power adapter.
15. AUX IN jack
Press to increase (+) or decrease (-) the
volume level from 0 to 30.
Connect external equipment to this jack.
16. FM.ANT (Antenna) jack
17. Receiver storage compartment
9.
(Previous) /
(Next) button
Skip to the previous/next track in iPhone/
iPod and wireless audio modes.
.8.
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control
1.
2.
(Power) button
Switch between power-on and standby
modes.
(Previous) /
(Next) button
Skip to the previous/next track in iPhone/
iPod and wireless audio modes. Hold the
button to fast-backward/fast-forward a track.
Decrease/increase the frequency or select a
preset channel number (from 01 to 20) in
tuner mode.
1
6
2
3
4
5
3.
(Play/Pause) button
Play/pause a track when listening to iPhone/
iPod or wireless audio source. Hold to switch
the iPod to sleep mode.
7
Note: When the unit is building a wireless
audio with an iPad, this button is disabled.
Save a radio channel in tuner mode.
4. SOURCE button
Select iPod, tuner, AUX or wireless audio
mode by pressing repeatedly.
5. MUTE button
Turn off the sound. Press again to restore the
sound output.
6. U-Cubed button
Activate or deactives U-Cubed (High Definition
Wide Stereo) sound effect.
7. VOL +/- button
Press to increase (+) or decrease (-) the
volume level from 0 to 30.
Selecting the Sound Source
This system enables you to access one of the four basic
functions - iPod, tuner, AUX and wireless audio.
or
Press SOURCE button on the unit or remote control to select
On the Unit
On the Remote Control
one of the sound sources.
.9.
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing back from iPhone/iPod
Setting an iPhone/iPod on the Unit
Compatible iPod Players: Most Apple iPod
models with 30-pin dock connectors as
follows: iPod nano 5th generation (video
camera), iPod nano 4th generation (video),
iPod nano 3rd generation (video), iPod nano
2nd generation (aluminum), iPod nano 1st
generation, iPod 4th generation (color
display), iPhone 3G/3GS, iPhone 4, iPod
classic, iPod 5th generation (video), iPod 4th
generation, iPod touch 1st generation, iPod
touch 2nd generation, iPhone, iPod mini.
3. Connect your iPhone/iPod. Make sure the
connector plug of unit is firmly inserted into
the connector port of iPhone/iPod.
1. Select the appropriate dock adapter made
for your iPhone/iPod.
Notes:
Use one of the supplied dock adapters or your
own from the Apple Inc.
Always set volume to the minimum when
connecting or disconnecting the other
equipment.
An identification number is marked on the
dock adapter.
When you connect your iPhone/iPod to unit,
make sure you insert it all the way.
Supplied
Dock adapter
Identification
Number
iPod Models Supported
15
14
iPhone 3G/3GS
Listening to an iPhone/iPod
iPod Touch
1. Press the " " button to power on the system
from standby mode.
It is recommended to use an appropriate
dock adapter to protect your iPhone/iPod.
2.Insert the dock adapter as illustrated. The
small slot at the dock adapter should be at
the backside.
LCD Display
2. Select "iPod" mode with the SOURCE button.
a. Match the dock adapter tabs to the front
holes in the cradle.
b. Press the other side onto the cradle until
a click sound.
Slot*
LCD Display
b
3. When iPhone/iPod is selected as the sound
source, it automatically starts playback.
a
Remove the iPod
dock adapter with
your fingernail by
using the slot.
.10.
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the Button
Functions
Unit
/
Remote Control
Start/Pause playback.
Hold this button to switch the iPod to sleep mode.
Next track/fast forward (press and hold).
Previous track/rewind (press and hold).
Charging an iPhone/iPod
iPod is a trademark of Apple Inc., registered in
The iPhone/iPod is charged while it is set on the
unit when the unit is powered on.
the U.S. and other countries.
iPhone is a trademark of Apple Inc.
The unit does not support iPod 3G (10/15/20/
30/40GB) charging mode.
We are not responsible for any loss of or
damage to iPhone/iPod that might result
from the use of this product.
Make sure the AC adapter is connected to
the unit.
Sound distortion may occur when playing back
audio sources with high recording levels.
When distortion occurs, it is recommended
to turn off the equalizer of the iPhone/iPod.
For information on operating the iPhone/iPod,
see the iPhone/iPod instruction manual.
If you do not turn on the power of this unit
and only connect the iPhone/iPod to this
unit,power may be supplied to the iPhone/iPod.
"Made for iPod" and "Made for iPhone" and
"Made for iPad" mean that an electronic
accessory has been designed to connect
specifically to iPod/iPhone/iPad and has
been certified by the developer to meet
Apple performance standards.
The iPhone/iPod is charged regardless of the
sound source selected on the unit.
See the iPhone/iPod instruction manual about
the details of iPhone/iPod charging.
Notes for Caring Your iPhone/iPod:
The connector plug is protected with a cover
when it is first purchased. Please remove the
cover before operating the unit.
This unit can only play the iPhone/iPod audio.
You can use the iPhone/iPod video function
and hear the audio but cannot play the
video.
Do not carry the System with iPhone/iPod
connected. You might drop it down or it
might cause damages to the connector part.
Do not touch or hit the iPhone/iPod terminal
pins or the connector pins directly. It might
cause damages to the connector part.
If the iPhone/iPod does not play correctly,
please update your iPhone/iPod software to
Apple is not responsible for the operation of
this device or its compliance with safety and
regulatory standards.
the latest version.
-
For details about
updating your iPhone/iPod, check on the
Apple web site <http://www.apple.com>.
.11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing back via Bluetooth/from iPad
Notes:
Downloading the SoundFreaq App
A "receiver" was set in the receiver storage
compartment at the factory.
We have developed an App to give you
full control from your iPhone/iPad while
playing audio over the Bluetooth wireless
connection, please download the
"SoundFreaq Remote" App for FREE.
The Bluetooth connection can be completed
in standby mode or power-on mode.
If your mobile phone supports A2DP protocol,
its music will play through the unit.
You can build a Bluetooth connection with a
mobile phone, an iPad or any other
Bluetooth-enabled devices.
After you build a Bluetooth connection
between your iPhone/iPad and the Sound
Platform, a prompt will be displayed on
your iPhone/iPad asking you if you would
like to install our App, click "Yes" to install
the APP. After a while, "For his Accessory"
page will appear on your iPhone/iPad.
Enter the "User Name" and "Password" in
the iTune. After pressing the "FREE"
button, press the "INSTALL APP" button
that will appear to install the APP for your
unit. When the installation is finished, you
can control the playback from your
iPhone/iPad.
1. Press the "
" button to power on the system
from standby mode.
The pair indicator lights up when the unit is
powered on from the standby mode.
2. Press the PAIR button on the unit to put the
unit into the pair mode.
The Pair indicator starts blinking at a fast rate.
If the unit has previously linked with your
Bluetooth-enabled device, you only need to
turn on the unit and select the Bluetooth mode,
no further operation is needed.The Pair
indicator will blink at a lower rate.
If you hold the PAIR button during the process
of pairing, the operation will be cancelled.
You can click "No" to choose not to
download the App and still play music via
the Bluetooth connection but you will
have limited control, we suggest you
download the App.
Main Unit
PAIR Button
3. During this period,you can operate the mobile
phone,iPad or Bluetooth-enabled device to
pair with the unit within a 33 feet (10m)
range.
.12.
Download from Www.Somanuals.com. All Manuals Search And Download.
Please check the user manual of the iPad or
Bluetooth-enabled device with which you
are initiating pair to learn about Bluetooth
connection with any other devices.
This device is now the connected device to the
Sound Platform (the previous connected device is
now disconnected). Repeat those steps to
switch the connected device again.
4. Once the unit is detected and its name
"Sound Platform" appears on the display of
your iPad or Bluetooth-enabled device, key
in the default password "1234" if a prompt
requests it.
Note: If the unit has no sound output, please
check if the volume level of your Bluetooth
device connected to the system is set to the
minimum, or the Bluetooth device is muted.
You may change the device name on your
Bluetooth-enabled device after the pair is
successfully set up.
Playing back from Macbook or Macbook Pro:
1. In the desktop screen, Select the “Open
Bluetooth Preference”.
2. If there is any old“Sound Platform”records,
remove it. And then select “Setup New
Device”again.
3. Select “Sound Pla”and the type should be
“Audio”in the latest SFQ-01 unit.
Click the “Continue”to proceed pairing
process.
4. Once completed, the pairing success screen
will come out.
The pair indicator starts blinking quickly to
indicate that the unit and your device have
put into the connection mode.
When a Bluetooth connection is established
successfully, the indicator starts blinking
slowly.
If the Bluetooth connection is completed in
the Bluetooth display, and a prompt chime
will sound.
5. Select Bluetooth mode by repeatedly pressing
the SOURCE button on the unit or remote
control.
Note: Don’t quit the page immediately. You
may notice that the previous dialog screen
still shows the device not connected. Just
ignore it. It’s confusing to the user. In fact,
it’s connected already.
6. Select the desired music and press "Play"
button on your device.The unit automatically
starts playing the audio.
Try again above steps 2 to 5 if the Pair
indicator on the unit lights solidly.
5. Open iTune, play a song. Then use mouse to
click the Bluetooth icon and the top right
hand corner of the desktop screen, select
the “Sound Platform”option and then select
the“Use as Audio Device (Stereo)”. After a while
(a few seconds), the music will come out
from the SFQ-01. If not, retry to select the“Use
as Audio Device (Stereo)”once again. The
sound Quality should be good.
Using multiple Bluetooth devices:
Only one device can be used at a time, but you
can switch between different Bluetooth devices.
Make sure each device you want to use has
already been paired, to switch devices:
1. On the Sound Platform, press the pair button
2. On the Bluetooth device, select connect to
the Sound platform.
.13.
Download from Www.Somanuals.com. All Manuals Search And Download.
Upgrading Wireless Connection Mode
3. Set a new "receiver" into the storage compartment
as shown.
You can purchas a 2.4G wireless receiver to
upgrade the connection mode by replacing
the receiver located in the storage compartment
on the back of unit.
If you have any question, please consult your
dealer.
"THIS SIDE UP" is
marked on the
receiver.
1. Open the cover of receiver storage compartment
located on the back of unit.
2. Remove the "receiver" from the storage
compartment.
Make sure the new "receiver" is well
connected to the system.
4. Close the "receiver" storage cover.
DO NOT REMOVE RECEIVER UNLESS YOU ARE UPGRADING WIRELESS CONNECTION MODE. PLEASE
VISIT SOUNDFREAQ.COM FOR FURTHER DETAILS.
.14.
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to Tuner
Press the Button
Unit Remote Control
Functions
/
Switch between the frequency display and channel number display.
Tune the desired frequency or channel number based on the
different display.
Frequency display
Channel number display
Hold this button to enter saving mode. Press to save a channel.
(see "Presetting a station”)
Select a channel (from 01 to 20).
Change frequency from 87.5MHz to 108.0MHz in FM mode.
Hold for more than one second to activate the Auto Scan function,
and then release the button. The frequency will be scanned
automatically until a radio station is found. Or press again to quit
search while searching.
Listening to a Station
Note: Position the antenna as far away as
possible from the AC adapter, a TV, or other
radiation source.
LCD Display
1. Plug the supplied FM antenna into the
FM.ANT jack located on the back of unit.
4. Select a desired radio station for listening.
5. Move the antenna around to get the best
reception.
6. If necessary, adjust the volume level.
Presetting a Station
1. Select tuner mode with the SOURCE button.
FM Antenna
2. Press the
"
"
button to power on the
system from standby mode.
LCD Display
2. Switch to the frequency display if the display
is channel number.
3. Tune a desired frequency. You can use either
of the below methods to tune the frequency.
LCD Display
3. Select tuner mode with the SOURCE button.
.15.
Download from Www.Somanuals.com. All Manuals Search And Download.
A. Manual Tuning - Briefly press "
"/ "
"
5. Use " "/ " " on the unit or remote control
to select the channel number (from 01 to 20)
to be set.
button repeatedly to move frequency to
frequency (from 87.5 MHz to 108.0 MHz)
until you find the desired station.
6. Press "
" button again to store the frequency.
The selected frequency will then be stored
with the preset channel number.
The "SAVED" is displayed during the saving
operation.
LCD Display
The display will be switched automatically to
channel number display after a few seconds.
B. Auto Scanning - Hold "
"/ "
" button
until the frequency display starts flashing.
The frequency will be scanned automatically
until a station is found.
4. Hold "
" button to start storing a station.
LCD Display
The channel number shows on the display.
LCD Display
LCD Display
Playing back from External Source
Listening to an External Audio
Device, Digital Music Player or Any
Other Audio Source
1. Turn the unit power on.
2. Set the volume to the minimum position.
3. Select AUX mode with the SOURCE button.
Connect an external device to the AUX IN jack
on the back panel of the unit using a stereo
mini plug cord (not supplied).
LCD Display
4. Start playback on the external device.
5. Adjust the volume level to the level that you
want to listen to.
To audio output such
as CD/MD/ digital
music player, etc.
LCD Display
Back Panel
Note: Volume level will be shown on the display
in the process of adjustment.
.16.
Download from Www.Somanuals.com. All Manuals Search And Download.
Activating "U-Cubed" Sound Effect
"U-Cubed" is an proprietary technology designed to create an ultra wide stereo sound
field in digital music systems. With exceptional natural sound reproduction of high definition and
fidelity, we create a listening experience where you feel like your speakers are separated much more
than they are.
To activate UQ3 on:
The unit, turn the "
" knob once to activate, turn again to deactivate.
" button to activate and deactivate.
On the remote or remote App, press the "
Notes:
The bass and treble cannot be adjusted when UQ3 is activated.
In tuner mode, the U-Cubed sound effect can not be activated.
.17.
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Check this list for a possible troubleshooting solution before calling for service.
In These Cases
Check the following points
Power does not come on.
• AC adapter is not inserted securely. Plug in securely.
• Is the selected dock adapter compatible to your iPhone/iPod?
• Is the dock adapter properly mounted on the unit? Make sure to mount the
dock adapter properly.
Cannot set the iPhone/iPod.
Cannot operate iPhone/iPod.
• Is the connector plug of the unit firmly inserted into the connector port of
the iPhone/iPod?
• Is the iPhone/iPod properly functioning? Test the iPhone/iPod functions in
stand-alone condition.
• Is the connector plug of the unit firmly inserted into the connector port
of the iPhone/iPod?
iPhone/iPod cannot be
charged.
• Is the AC adapter plug firmly inserted into DC IN jack of the unit?
• The antenna is not properly extended or positioned.
• Tune to the correct radio channel/frequency.
Hard to listen to broadcasts
because of noise.
• Making sure the antenna is further away from any equipment that may be
causing the noise or interference.
• The path between the remote control and the sensor on the unit is
blocked.
Unable to operate the
System from the remote
control.
• The battery of remote control is exhausted.
• Check if the volume level is set to the minimum.
• Check if the volume level of your Bluetooth device connected to the system is
set to the minimum.
No sound output.
• Check if the volume level is muted. Press MUTE button on the unit again to
restore the sound output.
• Check to make sure your Bluetooth device is not muted.
The system does not react
when the buttons are
pressed.
• Remove and reconnect the AC power plug and turn on the system again.
• After the indicator blinks quickly for 3 seconds, the system enters the protection
mode. The unit may be turned on for long time. Decrease the volume level on
your external audio system, and then turn on the system again.
The system is suddenly
powered off in AUX mode.
.18.
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
SFQ-01
Model
Type
Sound Platform
Support Bluetooth
Bluetooth 1.2, 2.0 and 2.1 compliant
Support Profile
A2DP
Input Sensitivity/Impedance
AUX Input
Band
1200 mV
FM
Tuning Range
Frequency Step
Preset Stations
87.5 ~ 108.0 MHz
100 KHz
20
Tuner
Input Terminal
Power Source
External DC IN (for AC adapter), AUX IN
DC 18 V 3.3 A (External DC IN)
Input: AC 100-240V, 50/60Hz
Output: DC 18 V 3.3 A
AC Adapter
Dimensions (Approx.)
Weight
320mm (W) * 168mm (H) * 154mm (D)
2.01Kg (including receiver)
.19.
Download from Www.Somanuals.com. All Manuals Search And Download.
Save this manual
Download from Www.Somanuals.com. All Manuals Search And Download.
|