3-865-324-E2 (1)
Vid e o Ca sse t t e
Re co rd e r
Operating Instructions
PAL NTSC 4.43
SLV-SE70NP1/NP2/VC1/VC2
SLV-SX70VC
©1999 by Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Ta b le o f co n t e n t s
Ge t t in g St a rt e d
4
5
9
Step 1: Unpacking
Step 2: Setting up the remote commander
Step 3: Connecting the VCR
14 Step 4: Tuning your TV to the VCR
16 Step 5: Setting up the VCR with the Auto Set Up function
19 Step 6: Setting the clock
24 Selecting a language
26 Presetting channels
30 Changing/ disabling programme positions
36 Setting the PAY-TV/ Canal Plus decoder
68 Adjusting the picture
Ba sic Op e ra t io n s
41 Playing a tape
70 Changing menu options
73 Editing with another VCR
44 Recording TV programmes
49 Recording TV programmes using
the ShowView* system
Ad d it io n a l In fo rm a t io n
54 Setting the timer manually
75 Troubleshooting
78 Specifications
Ad d it io n a l Op e ra t io n s
79 Index to parts and controls
57 Playing/ searching at various
Back cover
speeds
Index
59 Setting the recording duration
time
60 Checking/ changing/ cancelling
timer settings
62 Recording stereo and bilingual
programmes
64 Searching using the Smart Search
function
67 Searching using the index
function
* ShowView is a trademark applied for by Gemstar Development Corp. ShowView system is
manufactured under license from Gemstar Development Corporation.
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Getting Started
St e p 1
Un p a ckin g
Check that you have received the following items with the VCR:
• Remote commander
• Aerial cable
• R6 (size AA) batteries
Ch e ckin g yo u r m o d e l n a m e
The instructions in this manual are for the 5 models: SLV-SE70NP1,
SE70NP2, SE70VC1, SE70VC2, and SX70VC. Check your model
number by looking at the rear panel of your VCR. The SLV-SE70VC1
is the model used for illustration purposes. Any difference in
operation is clearly indicated in the text, for example, “SLV-SE70NP1
only.”
4
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 2
Se t t in g u p t h e re m o t e co m m a n d e r
In se rt in g t h e b a t t e rie s
Insert two R6 (size AA) batteries by
matching the + and – on the
batteries to the diagram inside the
battery compartment.
Insert the negative (–) end first, then
push in and down until the positive
(+) end clicks into position.
Usin g t h e re m o t e co m m a n d e r
Remote sensor
You can use this remote
commander to operate this
VCR and a Sony TV. Buttons
on the remote commander
marked with a dot (• ) can be
used to operate your Sony TV.
If the TV does not have the g
symbol near the remote sensor,
this remote commander will
not operate the TV.
TV / VIDEO
1
4
2
5
3
6
To operate
the VCR
Set TV / VIDEO to
VIDEO and point at the remote sensor on the VCR
TV and point at the remote sensor on the TV
a Sony TV
continued
Getting Started
5
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 2 : Se t t in g u p t h e re m o t e co m m a n d e r (co n t in u e d )
I/u
V
WIDE
AUDIO MONITOR
;
FASTEXT buttons
DISPLAY
… TV/VIDEO
1
4
7
2
5
8
0
3
6
9
Programme
number
buttons
?
PROG+/–/
√/◊
Á +/–
TV control buttons
To
Press
Turn the TV into standby mode
I/ u
Select an input source of the TV either from
aerial in or from line in
… TV/ VIDEO
Select the programme position of the TV
Programme number buttons,
?, PROG +/ –
Adjust the volume of the TV
Á +/ –
6
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
To
Press
Switch to TV (Teletext off)
Switch to Teletext
Select the sound
; (TV)
V (Teletext)
AUDIO MONITOR
FASTEXT buttons
DISPLAY
Use FASTEXT
Call up on-screen display
Change the Teletext page
√/ ◊
Switch to/ from wide mode of a Sony wide TV (For
other manufacture’s wide TV, see “Controlling other
TVs with the remote commander” below.)
WIDE
Notes
•
•
With normal use, the batteries should last about three to six months.
If you do not use the remote commander for an extended period of time, remove
the batteries to avoid possible damage from battery leakage.
•
•
•
Do not use a new battery with an old one together.
Do not use different types of batteries together.
Some buttons may not work with certain Sony TVs.
Co n t ro llin g o t h e r TVs w it h t h e re m o t e co m m a n d e r
The remote commander is preprogrammed to control non-Sony TVs. If your
TV is listed in the table below, set the appropriate manufacturer’s code
number.
1
2
Set TV / VIDEO at the top of the remote commander to TV .
Hold down I/ u, and enter your TV’s code number(s) using the
programme number buttons. Then release I/ u.
Now you can use the following TV control buttons to control your TV:
I/ u, TV/ VIDEO, programme number buttons, ? (ten’s digit),
PROG +/ –, Á +/ –, ; (TV), V (Teletext), FASTEXT buttons, WIDE*,
MENU*, >*/ .*/ ?*/ /*, and OK*.
* These buttons may not work with all TVs.
Tip
•
When you set your TV’s code number correctly while the TV is turned on, the TV
turns off automatically.
continued
Getting Started
7
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 2 : Se t t in g u p t h e re m o t e co m m a n d e r (co n t in u e d )
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until
you find the one that works with your TV.
To make wide mode settings, see the footnotes below this table for the
applicable code numbers.
Code number
Manufacturer
Code number
Manufacturer
1
1
17* , 49
Sony
01* , 02
Panasonic
Philips
1
1
1
06* , 07* , 08*
Akai
68
52
12, 13
22, 23
25
Ferguson
Grundig
Hitachi
JVC
Saba
1
1
10* , 11*
24
Samsung
Sanyo
29
33
Sharp
36
Loewe
Mivar
NEC
45
Telefunken
Thomson
Toshiba
2
43*
09, 70
66
38
3
Nokia
15, 16, 69*
1
* Press WIDE to switch the wide picture mode on or off.
2
* Press WIDE, then press Á +/ – to select the wide picture mode you want.
3
* Press WIDE. The menu appears on the TV screen. Then, press >/ ./ ?/ / to
select the wide picture you want and press OK.
Notes
•
If the TV uses a different remote control system from the one programmed to work
with the VCR, you cannot control your TV with the remote commander.
•
•
If you enter a new code number, the code number previously entered will be erased.
When you replace the batteries of the remote commander, the code number may
change. Set the appropriate code number every time you replace the batteries.
8
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 3
Co n n e ct in g t h e VCR
If your TV has a EURO-AV connector, see page 10.
If yo u r TV d o e s n o t h a ve a EURO-AV (Sca rt )
co n n e ct o r
AERIAL IN
AERIAL OUT
Mains lead
to mains
AERIAL IN
Aerial cable (supplied)
: Signal flow
1
Disconnect the aerial cable from your TV
and connect it to AERIAL IN on the rear
AERIAL
ANTENNE
IN
ENTREE
panel of the VCR.
OUT
SORTIE
AERIAL
ANTENNE
2
3
Connect AERIAL OUT of the VCR and
the aerial input of your TV using the
supplied aerial cable.
IN
ENTREE
OUT
SORTIE
Connect the mains lead to the mains.
Note
•
When you connect the VCR and your TV only with an aerial cable, you have to set
RF MODULATOR in the OPTIONS-2 menu to ON (initial setting) (see page 72).
continued
Getting Started
9
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 3 : Co n n e ct in g t h e VCR (co n t in u e d )
If yo u r TV h a s a EURO-AV (Sca rt ) co n n e ct o r
AERIAL IN
: LINE-1
(TV)
AERIAL OUT
Mains lead
AERIAL IN
to mains
Aerial cable (supplied)
EURO-AV
(Scart)
: Signal flow
EURO-AV cable (not supplied)
1
2
Disconnect the aerial cable from your
TV and connect it to AERIAL IN on the
rear panel of the VCR.
AERIAL
ANTENNE
IN
ENTREE
OUT
SORTIE
AERIAL
ANTENNE
Connect AERIAL OUT of the VCR and
the aerial input of your TV using the
supplied aerial cable.
IN
ENTREE
OUT
SORTIE
10 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Connect LINE-1 (TV) on the VCR and
the EURO-AV (Scart) connector on the
TV with the optional EURO-AV cable.
This connection improves picture and
sound quality. Whenever you want to
watch the VCR picture, press
… TV/ VIDEO to display the VIDEO
indicator in the display window.
Connect the mains lead to the mains.
Note
•
If the TV is connected to the LINE-1 (TV) connector, setting the RF MODULATOR in
the OPTIONS-2 menu to OFF is recommended. In the OFF position, only the signal
from the aerial is output through the AERIAL OUT connector (see page 72). You do
not have to tune your TV to the VCR. Skip “Tuning your TV to the VCR” on page
14.
Ab o u t t h e SMARTLINK fe a t u re s
If the connected TV complies with
SMARTLINK
1
2
SMARTLINK, MEGALOGIC* , EASYLINK* ,
3
4
Q-Link* , or EURO VIEW LINK* , you can use
the SMARTLINK function after you complete
the steps on the previous page (the SMARTLINK indicator appears in the VCR’s
display window when you turn on the TV). You can enjoy the following
SMARTLINK features.
• Preset Download
You can download your TV tuner preset data to this VCR and tune the VCR
according to that data in Auto Set Up. This greatly simplifies the Auto Set Up
procedure. Be careful, not to disconnect the cables or exit the Auto Set Up function
during the procedure.
See “Setting up the VCR with the Auto Set Up function” on page 16.
continued
Getting Started
11
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 3 : Co n n e ct in g t h e VCR (co n t in u e d )
• TV Direct Rec
You can easily record what you are watching on the TV (other than tapes being
played on this VCR). For details, see “Recording what you are watching on the TV
(TV Direct Rec)” on page 48.
• One Touch Play
With One Touch Play, you can start playback automatically without turning on the
TV. For details, see “Starting playback automatically with one button (One Touch
Play)” on page 43.
• One Touch Menu
You can turn on the VCR and TV, set the TV to the video channel, and display the
VCR’s on-screen display automatically by pressing MENU on the remote
commander.
• One Touch Timer
You can turn on the VCR and TV, set the TV to the video channel, and display the
timer recording menu (the TIMER METHOD menu, the TIMER menu, or the
SHOWVIEW menu) automatically by pressing
commander.
TIMER on the remote
You can set which timer recording menu is displayed using TIMER OPTIONS in the
OPTIONS-2 menu (see page 72).
• Automatic Power Off
You can have the VCR turn off automatically, if the VCR is not used after you turn
off the TV.
1
*
“MEGALOGIC” is a registered trademark of Grundig Corporation.
“EASYLINK” is a trademark of Philips Corporation.
“Q-Link” is a trademark of Panasonic Corporation.
2
*
3
*
4
*
“EURO VIEW LINK” is a trademark of Toshiba Corporation.
Note
•
Not all the TVs respond to the functions above.
12 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Ad d it io n a l co n n e ct io n s
To a stereo system
You can improve sound quality by
connecting a stereo system to the
AUDIO OUT R/ L jacks as shown on the
right.
AUDIO OUT
R/L
LINE IN
Audio cable (not supplied)
: Signal flow
To a satellite tuner
You can watch programmes from the
satellite tuner connected to this VCR on
the TV even when the VCR is turned off
using the Line Through function. When
you turn on the satellite tuner, this VCR
automatically sends the signal from the
satellite tuner to the TV without turning
itself on.
DECODER/
… LINE-2 IN
LINE OUT
EURO-AV cable (not supplied)
: Signal flow
1
Connect the satellite tuner to the DECODER/ LINE-2 IN connector as shown
above.
2
3
4
Set DECODER/ LINE2 to LINE2 in the OPTIONS-2 menu.
Set POWER SAVE to OFF in the OPTIONS-2 menu.
Turn off the VCR.
To watch a satellite programme, turn on the satellite tuner and the TV.
Note
•
You cannot watch satellite programmes on the TV while recording unless you
record a satellite programme.
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
13
St e p 4
Tu n in g yo u r TV t o t h e VCR
If you have connected the VCR to your TV using the EURO-AV cable,
skip this step.
I/u ON/STANDBY
PROGRAM +/–
RF CHANNEL
ON/STANDBY
1
2
Press I/ u ON/ STANDBY to turn on the VCR.
Press RF CHANNEL on the VCR lightly.
The factory-preset RF channel appears in the display window.
The VCR signal is output through this channel to the TV.
RF CHANNEL
3
Turn on your TV and select a programme position for the VCR
picture.
This programme position will now be referred to as the video
channel.
14 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
Tune the TV to the same channel as that
shown in the display window so that
the picture on the right appears clearly
on the TV screen.
SONY VIDEO CASSETTE RECORDER
Refer to your TV manual for tuning
instructions.
If the picture does not appear clearly,
see “To obtain a clear picture from the
VCR” below.
Press RF CHANNEL.
You have now tuned your TV to the VCR. Whenever you want to
play a tape, set the TV to the video channel.
RF CHANNEL
To check to see if the TV tuning is correct
Set the TV to the video channel and press PROGRAM +/ – on the VCR. If
the TV screen changes to a different programme each time you press
PROGRAM +/ –, the TV tuning is correct.
To obtain a clear picture from the VCR
If the screen does not appear clearly in step 4 above, press PROGRAM +/ –,
so that another RF channel appears. Then tune the TV to the new RF
channel until a clear picture appears.
Getting Started
15
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 5
Se t t in g u p t h e VCR w it h t h e Au t o Se t
Up fu n ct io n
Before using the VCR for the first time, set up the VCR using the Auto
Set Up function. With this function, you can set the language for the
on-screen display, TV channels, guide channels for the ShowView
system, and VCR clock automatically.
AUTO SET UP
PROGRAM +/–
AUTO
SET UP
1
Hold down AUTO SET UP on the VCR for more than three seconds.
The VCR automatically turns on, and the country abbreviation
appears in the display window.
16 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAM
2
Press PROGRAM +/ – to select the abbreviation of your country.
For some countries, there is a selection of languages to choose from.
The abbreviations of the countries and languages are as follows:
SLV-SE70VC1/SE70VC2/SX70VC
Abbreviation Country
Language
German
German
French
Abbreviation
Language
Greek
Country
Greece
A
Austria
GR
I
B-D
B-F
B-N
CH-D
CH-F
CH-I
D
Belgium
Italian
Italy
Belgium
L-D
L-F
NL
P
German
French
Luxemburg
Luxemburg
Netherlands
Portugal
Belgium
Dutch
Switzerland
Switzerland
Switzerland
Germany
Spain
German
French
Dutch
Portuguese
English
Italian
ELSE
Other
countries
German
Spanish
E
SLV-SE70NP1/SE70NP2
Abbreviation Country
Language
German
German
French
Abbreviation
Language
German
French
Country
A
Austria
L-D
L-F
N
Luxemburg
Luxemburg
Norway
B-D
B-F
B-N
CH-D
CH-F
D
Belgium
Belgium
Belgium
Switzerland
Switzerland
Germany
Denmark
Spain
Danish
Dutch
NL
P
Dutch
Netherlands
Portugal
German
French
Portuguese
Swedish
Finnish
English
S
Sweden
German
Danish
Spanish
SF
Finland
DK
E
ELSE
Other
countries
If your country does not appear, select ELSE.
continued
Getting Started
17
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 5 : Se t t in g u p t h e VCR w it h t h e Au t o Se t Up fu n ct io n
(co n t in u e d )
AUTO
SET UP
3
Press AUTO SET UP lightly.
The VCR starts searching for all of the receivable channels and
presets them in the appropriate order for your local area.
If you use the SMARTLINK connection, the Preset Download
function starts and the SMARTLINK indicator flashes in the display
window during download.
After the search or download is complete, the current time appears
in the display window for any stations that transmit a time signal.
To cancel the Auto Set Up function
Press AUTO SET UP.
Tip
•
If you want to change the language for the on-screen display from the one preset in
the Auto Set Up function, see page 24.
Note
Do not cancel the Auto Set Up function during step 3. If you do, repeat the steps
above.
•
18 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 6
Se t t in g t h e clo ck
MENU
You must set the time and date on the
VCR to use the timer recording features
properly.
>/./?//
OK
The Auto Clock Set function works only
if a station in your area is broadcasting a
time signal. If the Auto Set Up function
did not set the clock correctly for your
local area, try another station for the
Auto Clock Set function.
Se t t in g t h e clo ck m a n u a lly
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
MENU
SETTINGS
1
Press MENU, then press >/ . to
highlight SETTINGS and press OK.
TUNER
CLOCK
LANGUAGE
RETURN
PLAY
OK
SELECT
SET
:
: OK
EXIT : MENU
CLOCK
2
Press >/ . to highlight CLOCK, then
press OK.
PLAY
OK
AUTO ADJUST
CLOCK PROG
MANUAL ADJUST
OFF
1
. 1 . 1 9 9 9
FRI
0 : 0 0
SELECT
SET
:
: OK
EXIT : MENU
continued
Getting Started
19
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 6 : Se t t in g t h e clo ck (co n t in u e d )
CLOCK
3
4
5
6
Press >/ . to highlight MANUAL
PLAY
OK
ADJUST, then press OK.
AUTO ADJUST
CLOCK PROG
MANUAL ADJUST
OFF
1
. 1 . 1 9 9 9
FRI
0 : 0 0
SELECT
SET
:
:
CONFIRM : OK
EXIT : MENU
CLOCK
Press >/ . to set the date.
PLAY
OK
AUTO ADJUST
CLOCK PROG
MANUAL ADJUST
2 8 . 1 . 1 9 9 9
OFF
THU
0 : 0 0
SELECT
SET
:
:
CONFIRM : OK
EXIT : MENU
CLOCK
Press / to highlight the month and set
the month pressing >/ ..
AUTO ADJUST
CLOCK PROG
MANUAL ADJUST
2 8 . 9 . 1 9 9 9
OFF
PLAY
OK
TUE
0 : 0 0
SELECT
SET
:
:
CONFIRM : OK
EXIT : MENU
CLOCK
Set the year, hour, and minutes in
sequence, pressing / to highlight the
item to be set, and press >/ . to select
the digits.
PLAY
OK
AUTO ADJUST
CLOCK PROG
MANUAL ADJUST
2 8 . 9 . 1 9 9 9
OFF
TUE
1 8 : 0 0
The day of the week is set automatically.
SELECT
SET
:
:
CONFIRM : OK
EXIT : MENU
20 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
CLOCK
7
8
Press OK to start the clock.
PLAY
OK
AUTO ADJUST
CLOCK PROG
MANUAL ADJUST
2 8 . 9 . 1 9 9 9
OFF
TUE
1 8 : 0 0
SELECT
SET
:
: OK
EXIT : MENU
MENU
Press MENU to exit the menu.
Tips
•
To change the digits during setting, press ? to return to the item to be changed,
and select the digits pressing >/ ..
•
If you want to return to the previous menu, highlight RETURN and press OK.
Note
•
The menu disappears automatically if you don’t proceed for more than a few
minutes.
continued
Getting Started
21
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 6 : Se t t in g t h e clo ck (co n t in u e d )
Ch a n g in g t h e st a t io n fo r
t h e Au t o Clo ck Se t fu n ct io n
MENU
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
>/.
OK
MENU
SETTINGS
1
2
3
Press MENU, then press >/ . to
highlight SETTINGS and press OK.
TUNER
CLOCK
LANGUAGE
RETURN
PLAY
OK
SELECT
SET
:
: OK
EXIT : MENU
CLOCK
Press >/ . to highlight CLOCK, then
press OK.
PLAY
OK
AUTO ADJUST
CLOCK PROG
MANUAL ADJUST
2 8 . 9 . 1 9 9 9
ON
1
AAB
TUE
1 8 : 0 0
AUTO ADJUST is highlighted.
SELECT
SET
:
: OK
EXIT : MENU
Press OK.
CLOCK
PLAY
OK
AUTO ADJUST
CLOCK PROG
MANUAL ADJUST
2 8 . 9 . 1 9 9 9
ON
OFF
TUE
1 8 : 0 0
SELECT
:
CONFIRM : OK
EXIT : MENU
22 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
CLOCK
4
5
6
Press >/ . to highlight ON, then press
OK.
PLAY
OK
AUTO ADJUST
CLOCK PROG
MANUAL ADJUST
2 8 . 9 . 1 9 9 9
ON
1
AAB
TUE
1 8 : 0 0
SELECT
SET
:
: OK
EXIT : MENU
CLOCK
Press . to highlight CLOCK PROG, then
press OK.
PLAY
OK
AUTO ADJUST
CLOCK PROG
MANUAL ADJUST
2 8 . 9 . 1 9 9 9
1
AAB
1 8 : 0 0
TUE
SELECT
:
CONFIRM : OK
EXIT : MENU
CLOCK
Press >/ . repeatedly until the
programme position of the station that
carries the time signal appears.
PLAY
OK
AUTO ADJUST
CLOCK PROG
MANUAL ADJUST
2 8 . 9 . 1 9 9 9
2
CDE
1 8 : 0 0
TUE
If the VCR does not receive the time
signal from any station, AUTO ADJUST
returns to OFF automatically.
SELECT
:
CONFIRM : OK
EXIT : MENU
MENU
7
Press MENU to exit the menu.
Tips
•
If you set AUTO ADJUST to ON, the Auto Clock Set function is activated whenever
the VCR is turned off. The time is adjusted automatically by making reference to the
time signal from the station whose programme position is displayed in the “CLOCK
PROG” row.
If you do not need the Auto Clock Set, select OFF.
•
If you want to return to the previous menu, highlight RETURN and press OK.
Note
•
The menu disappears automatically if you don’t proceed for more than a few
minutes.
Getting Started
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Se le ct in g a
la n g u a g e
MENU
You can change the on-screen display
language from the one you selected with
the Auto Set Up function.
>/.
OK
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
MENU
SETTINGS
1
2
Press MENU, then press >/ . to
highlight SETTINGS and press OK.
TUNER
CLOCK
LANGUAGE
RETURN
PLAY
OK
SELECT
SET
:
: OK
EXIT : MENU
Example: SLV-SE70VC2
Press >/ . to highlight LANGUAGE,
then press OK.
LANGUAGE
PLAY
OK
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
PORTUGUÊS
NEDERLANDS
EΛΛHNIKA
SELECT
SET
:
: OK
EXIT : MENU
3
Press >/ . to highlight the desired language, then press OK.
PLAY
OK
24 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU
4
Press MENU to exit the menu.
Tip
•
If you want to return to the previous menu, highlight RETURN and press OK.
Note
The menu disappears automatically if you don’t proceed for more than a few
minutes.
•
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Pre se t t in g
ch a n n e ls
PROG +/–
MENU
If some channels could not be preset
using the Auto Set Up function, you can
preset them manually.
>/./?//
OK
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
MENU
SETTINGS
1
2
3
Press MENU, then press >/ . to
highlight SETTINGS and press OK.
TUNER
CLOCK
LANGUAGE
RETURN
PLAY
OK
SELECT
SET
:
: OK
EXIT : MENU
TUNER
Press >/ . to highlight TUNER, then
press OK.
PROG.
1
PLAY
OK
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
FINE TUNING
RETURN
NORMAL
C
1 2 AAB
OFF
ON
SELECT
SET
:
: OK
EXIT : MENU
TUNER
Press >/ . to highlight NORMAL/
CATV, then press OK.
PROG.
NORMAL
1
PLAY
OK
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
CATV
ON
FINE TUNING
RETURN
SELECT
:
CONFIRM : OK
EXIT : MENU
26 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
TUNER
4
5
Press >/ . to highlight NORMAL, then
PROG.
1
press OK.
PLAY
OK
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
FINE TUNING
RETURN
NORMAL
1 2 AAB
C
OFF
ON
To preset CATV (Cable Television)
channels, select CATV.
SELECT
SET
:
: OK
EXIT : MENU
• PROG
Press PROG +/ – to select the programme
position.
Selected programme
position
TUNER
PROG.
4
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
NORMAL
C
1 2 AAB
OFF
ON
FINE TUNING
RETURN
SELECT
SET
:
: OK
EXIT : MENU
TUNER
6
Press >/ . to highlight CHANNEL SET,
then press OK.
PROG.
AAB
4
PLAY
OK
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
C
1 2
ON
FINE TUNING
RETURN
SELECT
:
CONFIRM : OK
EXIT : MENU
continued
Getting Started
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre se t t in g ch a n n e ls (co n t in u e d )
7
Press >/ . repeatedly until the channel you want is displayed.
PLAY
OK
TUNER
The channels appear in the following
order:
PROG.
4
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
FINE TUNING
RETURN
C
2 7
ON
• VHF E2 - E12
• VHF Italian channel A - H
• UHF E21 - E69
SELECT
:
• CATV S1 - S20
CONFIRM : OK
EXIT : MENU
• HYPER S21 - S41
• CATV S01 - S05
If you know the number of the channel you want, press the
programme number buttons. For example, for channel 5, first press
“0” and then press “5.”
8
9
To allocate another channel to another programme position, repeat
steps 5 and 7.
MENU
Press MENU to exit the menu.
Disa b lin g u n w a n t e d p ro g ra m m e p o sit io n s
After presetting channels, you can disable unused programme positions. The
disabled positions will be skipped later when you press the PROG +/ –
buttons.
1
2
In step 7 above, press programme number button “0” twice to display
the number “00” beside CHANNEL SET.
Press MENU to exit the menu.
28 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
If t h e p ict u re is n o t cle a r
Normally, the Auto Fine Tuning (AFT) function automatically tunes in
channels clearly. If, however, the picture is not clear, you may also use the
manual tuning function.
1
Press PROG +/ – or the programme number buttons to select the
programme position for which you cannot obtain a clear picture.
2
3
4
Press MENU, then select SETTINGS and press OK.
Select TUNER, then press OK.
Select FINE TUNING, then press OK.
The fine tuning meter appears.
TUNER
PROG.
NORMAL
4
Selected programme
position
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
C
2 7
OFF
FINE TUNING
RETURN
SET
:
EXIT : MENU
5
Press ?/ / to get a clearer picture, then press MENU to exit the
menu.
Note that the AFT (Auto Fine Tuning) setting switches to OFF.
Tip
•
If you want to return to the previous menu, highlight RETURN and press OK.
Note
The menu disappears automatically if you don’t proceed for more than a few
minutes.
•
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Ch a n g in g /
d isa b lin g
p ro g ra m m e
p o sit io n s
MENU
>/.//
OK
After setting the channels, you can
change the programme positions and the
station names as you like. If any
programme positions are unused or
contain unwanted channels, you can
disable them.
Ch a n g in g p ro g ra m m e
p o sit io n s
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
MENU
LISTS
1
Press MENU, then press >/ . to
highlight LISTS and press OK.
CHANNEL LIST
TIMER LIST
RETURN
PLAY
OK
SELECT
SET
:
: OK
EXIT : MENU
CHANNEL LIST
2
Press >/ . to highlight CHANNEL LIST,
then press OK.
PLAY
OK
PROG
CH
NAME
AAB
CDE
1
2
3
4
5
C
C
C
C
C
1 2
0 3
5 6
2 7
0 9
FGH
SELECT
MOVE PROG
ERASE PROG
:
:
:
CLEAR
EXIT : MENU
30 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANNEL LIST
3
4
5
Press >/ . to highlight the row on which
you want to change the programme
position, then press /.
PLAY
OK
PROG
CH
NAME
AAB
CDE
1
2
3
4
5
C
C
C
C
C
1 2
0 3
5 6
2 7
0 9
FGH
To display other pages for programme
positions 6 to 60, press >/ . repeatedly.
SELECT
SET STATION NAME
CONFIRM
:
:
: OK
EXIT : MENU
CHANNEL LIST
Press >/ . until the selected channel row
moves to the desired programme
position.
PLAY
OK
PROG
CH
NAME
CDE
1
2
3
4
5
C
C
C
C
C
0 3
5 6
1 2
2 7
0 9
AAB
FGH
The selected channel is inserted at the
new programme position and the
intermediate channels are displaced to
fill the gap.
SELECT
SET STATION NAME
CONFIRM
:
:
: OK
EXIT : MENU
Press OK to confirm the setting.
PLAY
OK
6
7
To change the programme position of another station, repeat steps 3
to 5.
MENU
Press MENU to exit the menu.
Tip
If you want to return to the previous menu, highlight RETURN and press OK.
Note
The menu disappears automatically if you don’t proceed for more than a few
minutes.
•
•
continued
Getting Started
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a n g in g /d isa b lin g p ro g ra m m e p o sit io n s (co n t in u e d )
Ch a n g in g t h e st a t io n n a m e s
You can change the station names (up to
5 characters).
MENU
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
>/./?//
OK
MENU
LISTS
1
2
3
Press MENU, then press >/ . to
highlight LISTS and press OK.
CHANNEL LIST
TIMER LIST
RETURN
PLAY
OK
SELECT
SET
:
: OK
EXIT : MENU
CHANNEL LIST
Press >/ . to highlight CHANNEL LIST,
then press OK.
PLAY
OK
PROG
CH
NAME
AAB
CDE
1
2
3
4
5
C
C
C
C
C
1 2
0 3
5 6
2 7
0 9
FGH
SELECT
MOVE PROG
ERASE PROG
:
:
:
CLEAR
EXIT : MENU
CHANNEL LIST
Press >/ . to highlight the row on which
you want to change the station name,
then press /.
PLAY
OK
PROG
CH
NAME
AAB
CDE
1
2
3
4
5
C
C
C
C
C
1 2
0 3
5 6
2 7
0 9
FGH
To display other pages for programme
positions 6 to 60, press >/ . repeatedly.
SELECT
SET STATION NAME
CONFIRM
:
:
: OK
EXIT : MENU
32 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANNEL LIST
4
5
Press /.
PROG
CH
NAME
AAB
CDE
PLAY
OK
1
2
3
4
5
C
C
C
C
C
1 2
0 3
5 6
2 7
0 9
FGH
SELECT A CHARACTER
NEXT
CONFIRM
:
:
: OK
EXIT : MENU
CHANNEL LIST
Enter the station name.
PLAY
OK
PROG
CH
NAME
CAB
CDE
1 Press >/ . to select a character.
Each time you press >, the character
changes as shown below.
1
2
3
4
5
C
C
C
C
C
1 2
0 3
5 6
2 7
0 9
FGH
A n B n … n Z n a n b n … n z
n 0 n 1 n … n 9 n (symbols)
SELECT A CHARACTER
NEXT
CONFIRM
:
:
: OK
EXIT : MENU
n
(blank space) n A
2 Press / to set the next character.
The next space is highlighted.
To correct a character, press ?/ / until the character you want
to correct is highlighted, then reset it.
You can set up to 5 characters for the station name.
Press OK to confirm the new name.
6
7
PLAY
OK
MENU
Press MENU to exit the menu.
Tip
If you want to return to the previous menu, highlight RETURN and press OK.
Note
The menu disappears automatically if you don’t proceed for more than a few
minutes.
•
•
continued
Getting Started
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a n g in g /d isa b lin g p ro g ra m m e p o sit io n s (co n t in u e d )
Disa b lin g u n w a n t e d
p ro g ra m m e p o sit io n s
After presetting channels, you can
disable unused programme positions.
The disabled positions will be skipped
later when you press the PROG +/ –
buttons.
CLEAR
Before you start…
1
4
7
2
5
8
0
3
6
9
• Turn on the VCR and the TV.
• Set the TV to the video channel.
MENU
>/.
OK
MENU
LISTS
1
Press MENU, then press >/ . to
highlight LISTS, and press OK.
CHANNEL LIST
TIMER LIST
RETURN
PLAY
OK
SELECT
SET
:
: OK
EXIT : MENU
34 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANNEL LIST
2
3
4
Press >/ . to highlight CHANNEL LIST,
PLAY
OK
then press OK.
PROG
CH
NAME
AAB
CDE
1
2
3
4
5
C
C
C
C
C
1 2
0 3
5 6
2 7
0 9
FGH
SELECT
MOVE PROG
ERASE PROG
:
:
:
CLEAR
EXIT : MENU
EXIT : MENU
EXIT : MENU
CHANNEL LIST
Press >/ . to highlight the row on which
you want to disable.
PLAY
OK
PROG
CH
NAME
AAB
1
2
3
4
5
C
C
C
C
C
1 2
0 3
5 6
2 7
0 9
CDE
FGH
SELECT
MOVE PROG
ERASE PROG
:
:
:
CLEAR
CLEAR
CHANNEL LIST
Press CLEAR.
PROG
CH
1 2
0 3
NAME
AAB
CDE
The selected row will be cleared as shown
on the right.
1
2
3
4
5
C
C
C
C
2 7
0 9
FGH
SELECT
MOVE PROG
ERASE PROG
:
:
:
CLEAR
5
6
Repeat steps 3 and 4 for any other programme positions you want
to disable.
MENU
Press MENU to exit the menu.
Tip
•
If you want to return to the previous menu, highlight RETURN and press OK.
Notes
•
The menu disappears automatically if you don’t proceed for more than a few
minutes.
•
Be sure to select the programme position you want to disable correctly. If you
disable a programme position by mistake, you need to reset that channel manually.
Getting Started
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Se t t in g t h e PAY-TV/Ca n a l Plu s d e co d e r
You can watch or record PAY-TV/ Canal Plus programmes if you connect a
decoder (not supplied) to the VCR.
Co n n e ct in g a d e co d e r
PAY-TV/Canal Plus
EURO-AV cable
decoder
(supplied w ith decoder)
DECODER/… LINE-2 IN
EURO-AV
(Scart)
: Signal flow
AERIAL OUT
: LINE-1 (TV)
Aerial cable
(supplied)
AERIAL IN
EURO-AV
(Scart)
EURO-AV cable (not supplied)
36 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Se t t in g PAY-TV/Ca n a l Plu s
ch a n n e ls
To watch or record PAY-TV/ Canal Plus
programmes, set your VCR to receive
the channels using the on-screen display.
PROG +/–
MENU
Before you start…
• Turn on the VCR, the TV, and the
decoder.
• Set the TV to the video channel.
>/./?//
OK
MENU
OPTIONS
1
2
3
Press MENU, then press >/ . to
highlight OPTIONS and press OK.
OPTIONS - 1
OPTIONS - 2
RETURN
PLAY
OK
SELECT
SET
:
: OK
EXIT : MENU
OPTIONS - 2
Press >/ . to highlight OPTIONS-2, then
press OK.
PLAY
OK
DECODER / LINE2
TIMER OPTIONS
POWER SAVE
RF MODULATOR
TV DIRECT REC
RETURN
DECODER
VARIABLE
OFF
ON
ON
SELECT
SET
:
: OK
EXIT : MENU
OPTIONS - 2
Press >/ . to highlight
DECODER/ LINE2, then press OK.
PLAY
OK
DECODER / LINE2
TIMER OPTIONS
POWER SAVE
RF MODULATOR
TV DIRECT REC
RETURN
DECODER
LINE2
ON
ON
SELECT
:
CONFIRM : OK
EXIT : MENU
continued
Getting Started
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Se t t in g t h e PAY-TV/Ca n a l Plu s d e co d e r (co n t in u e d )
OPTIONS - 2
4
Press >/ . to highlight DECODER, then
press OK.
PLAY
OK
DECODER / LINE2
TIMER OPTIONS
POWER SAVE
RF MODULATOR
TV DIRECT REC
RETURN
DECODER
VARIABLE
OFF
ON
ON
SELECT
SET
:
: OK
EXIT : MENU
MENU
MENU
5
6
Press MENU to exit the menu.
SETTINGS
Press MENU, then press >/ . to
highlight SETTINGS and press OK.
TUNER
CLOCK
LANGUAGE
RETURN
PLAY
OK
SELECT
SET
:
: OK
EXIT : MENU
TUNER
7
8
Press >/ . to highlight TUNER, then
PROG.
1
press OK.
PLAY
OK
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
FINE TUNING
RETURN
NORMAL
1 2 AAB
C
OFF
ON
SELECT
SET
:
: OK
EXIT : MENU
TUNER
Press >/ . to highlight NORMAL/
CATV, then press OK.
PROG.
NORMAL
1
PLAY
OK
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
CATV
ON
FINE TUNING
RETURN
SELECT
:
CONFIRM : OK
EXIT : MENU
38 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
TUNER
9
Press >/ . to highlight NORMAL, then
PROG.
1
press OK.
PLAY
OK
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
FINE TUNING
RETURN
NORMAL
1 2 AAB
C
OFF
ON
To preset CATV (Cable Television)
channels, select CATV.
SELECT
SET
:
: OK
EXIT : MENU
• PROG
Selected programme
position
10
Press PROG +/ – to select the desired
programme position.
TUNER
PROG. 1 5
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
NORMAL
C
1 2 AAB
OFF
ON
FINE TUNING
RETURN
SELECT
SET
:
: OK
EXIT : MENU
TUNER
11
12
13
Press >/ . to highlight CHANNEL SET,
PROG. 1 5
then press OK.
PLAY
OK
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
FINE TUNING
RETURN
C
1 2
AAB
ON
SELECT
:
CONFIRM : OK
EXIT : MENU
TUNER
Press >/ . to select the PAY-TV/ Canal
Plus channels, then press OK.
PROG. 1 5
PLAY
OK
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
FINE TUNING
RETURN
NORMAL
0 2 LMN
C
OFF
ON
SELECT
SET
:
: OK
EXIT : MENU
TUNER
Press >/ . to highlight PAY-TV/
CANAL+, then press OK.
PROG. 1 5
NORMAL
PLAY
OK
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
ON
OFF
FINE TUNING
RETURN
SELECT
:
CONFIRM : OK
EXIT : MENU
continued
Getting Started
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Se t t in g t h e PAY-TV/Ca n a l Plu s d e co d e r (co n t in u e d )
TUNER
14
15
Press >/ . to highlight ON, then press
PROG. 1 5
OK.
PLAY
OK
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
FINE TUNING
RETURN
NORMAL
C
ON
ON
0 2
LMN
SELECT
SET
:
: OK
EXIT : MENU
MENU
Press MENU to exit the menu.
Tip
•
If you want to return to the previous menu, highlight RETURN and press OK.
Notes
•
•
The menu disappears automatically if you don’t proceed for more than a few
minutes.
To superimpose subtitles while watching PAY-TV/ Canal Plus programmes, make
both decoder-VCR and VCR-TV connections using 21-pin EURO-AV cables that are
compatible with the RGB signals. You cannot record subtitles on the VCR.
•
When you watch PAY-TV/ Canal Plus programmes using the RFU input of the TV,
press … TV/ VIDEO so that the VIDEO indicator appears in the display window.
40 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
Pla yin g a t a p e
6 EJECT
DISPLAY
CLEAR
1
4
7
2
5
8
0
3
6
9
· PLAY
P PAUSE
)# FF
p STOP
03 REW
NTSC PB
1
2
Turn on your TV and set it to the video channel.
Insert a tape.
The VCR turns on and starts playing
automatically if you insert a tape with its
safety tab removed.
continued
Basic Operations 41
Download from Www.Somanuals.com. All Manuals Search And Download.
Pla yin g a t a p e (co n t in u e d )
3
Press · PLAY.
PLAY
OK
When the tape reaches the end, it will rewind automatically.
Additional tasks
To
Press
Stop play
p STOP
Pause play
P PAUSE
Resume play after pause
Fast-forward the tape
Rewind the tape
Eject the tape
P PAUSE or · PLAY
)# FF during stop
03 REW during stop
6 EJECT
To play an NTSC-recorded tape
Set NTSC PB at the rear of the VCR according to the colour system of your
TV.
When your TV is
PAL only
Set NTSC PB to
ON PAL TV
NTSC 4.43
PAL and NTSC
To use the time counter
At the point on the tape that you want to find later, press CLEAR. The
counter in the display window resets to “0:00:00.” Search for the point
afterwards by referring to the counter.
SP VIDEO
OPC
To display the counter on the TV screen, press
DISPLAY.
42
Basic Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
•
•
•
The counter resets to “0:00:00” whenever a tape is reinserted.
The counter stops counting when it comes to a portion with no recording.
The time counter does not appear on the TV screen when using an NTSC-recorded
tape.
•
Depending on your TV, the following may occur while playing an NTSC-recorded
tape:
– The picture becomes black and white.
– The picture shakes.
– No picture appears on the TV screen.
– Black streaks appear horizontally on the TV screen.
– The colour density increases or decreases.
•
•
If you play back a tape in LP or EP mode with NTSC system, the sound is heard in
monaural.
While setting the menu on the TV screen, buttons for playback on the remote
commander do not function.
St a rt in g p la yb a ck a u t o m a t ica lly w it h o n e b u t t o n
(On e To u ch Pla y)
If you use the SMARTLINK connection, you can turn on the VCR and the
TV, set the TV to the video channel, and start playback automatically with
one button.
1
Insert a tape.
The VCR automatically turns on.
If you insert a tape with its safety tab removed, the TV turns on and
switches to the video channel. Playback starts automatically.
2
Press · PLAY.
The TV turns on and switches to the video channel automatically.
Playback starts.
Tip
•
When there already is a tape in the VCR, the VCR and the TV turn on, the TV is set
to the video channel, and playback starts automatically in one sequence when you
press · PLAY.
Note
When you use the One Touch Play function, leave the TV on or in the standby
mode.
•
Basic Operations 43
Download from Www.Somanuals.com. All Manuals Search And Download.
Re co rd in g TV
p ro g ra m m e s
COUNTER/
REMAIN
DISPLAY
SP/LP
… TV/VIDEO
1
4
7
2
5
8
0
3
6
9
INPUT
SELECT
PROG +/–
r REC
p STOP
1
Turn on your TV and set it to the video channel.
To record from a decoder, turn it on.
44
Basic Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
2
3
Insert a tape with its safety tab in place.
INPUT SELECT
Press INPUT SELECT until a programme position number appears
in the display window.
SP VIDEO
OPC
• PROG
4
5
Press PROG +/ – to select the programme position you want to
record.
SP VIDEO
OPC
SP / LP
Press SP/ LP to select the tape speed, SP or LP.
LP (Long Play) provides recording time twice as long as SP,
however, SP (Standard Play) produces better picture and audio
quality.
VIDEO
LP
OPC
REC
6
Press r REC to start recording.
The recording indicator lights up red in the display window.
VIDEO
Recording indicator
LP
OPC
To stop recording
Press p STOP.
continued
Basic Operations 45
Download from Www.Somanuals.com. All Manuals Search And Download.
Re co rd in g TV p ro g ra m m e s (co n t in u e d )
To check the remaining time
Press
DISPLAY. With the display on, press COUNTER/ REMAIN to
check the remaining time. Each time you press COUNTER/ REMAIN, the
time counter and the remaining time appear alternately. The remaining time
with the
indicator also appears in the display window.
SP
0 : 0 0 : 2 2
1 : 4 6
Time counter
Remaining time
To correctly check the remaining time of the tape, set TAPE LENGTH in the
OPTIONS-1 menu according to the tape type you use (see page 71).
To w atch another TV programme w hile recording
1
Press … TV/ VIDEO to turn off the VIDEO indicator in the display
window.
2
Select another programme position on the TV.
To save a recording
To prevent accidental erasure, break off the safety
tab as illustrated. To record on a tape again,
cover the tab hole with adhesive tape.
Safety tab
46
Basic Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Tips
•
To select a programme position, you can use the programme number buttons on the
remote commander. For two-digit numbers, press the ? (ten’s digit) button
followed by the programme number buttons.
•
•
•
You can select a video source from the LINE-1 (TV) or LINE-2 IN (Scart) connector
also using the INPUT SELECT button.
The display appears on the TV screen indicating information about the tape, but the
information won’t be recorded on the tape.
If you don’t want to watch TV while recording, you can turn off the TV.
When using a decoder, make sure to leave it on.
Notes
•
•
•
The display does not appear during still (pause) mode or slow-motion playback.
The display will not appear while playing an NTSC-recorded tape.
If a tape has portions recorded in both PAL and NTSC systems, the time counter
reading will not be correct. This discrepancy is due to the difference between the
counting cycles of the two video systems.
•
•
You cannot watch a PAY-TV/ Canal Plus programme while recording another
PAY-TV/ Canal Plus programme.
When you insert a non-standard commercially available tape, the remaining time
may not be correct.
•
•
The remaining time is intended for rough measurement only.
About 30 seconds after the tape begins playback, the tape remaining time will be
displayed.
continued
Basic Operations 47
Download from Www.Somanuals.com. All Manuals Search And Download.
Re co rd in g TV p ro g ra m m e s (co n t in u e d )
Re co rd in g w h a t yo u a re w a t ch in g o n t h e TV
(TV Dire ct Re c)
If you use the SMARTLINK connection, you can easily record what you are
watching on the TV (other than tapes being played on the VCR).
1
2
Insert a tape with its safety tab in place.
Press r REC while you are watching a TV programme or external
source.
The VCR automatically turns on, then the TV indicator lights up and
the VCR starts recording what you are watching on the TV.
Tips
•
The TV indicator appears in the display window after you press r REC in some
situations such as:
– when you are watching a source connected to the TV’s line input, or
– when the TV tuner preset data for the programme position is different from the
data in the VCR tuner preset.
•
•
If there is a tape with its safety tab in place in the VCR, the VCR automatically turns
on and starts recording what you are watching on the TV when you press r REC.
You can turn the TV Direct Rec function ON and OFF in the OPTIONS-2 menu (see
page 72).
Notes
•
You cannot record what you are watching using this method when the VCR is in the
following modes; pause, timer standby, tuner preset, Auto Set Up, and recording.
•
When the TV indicator is lit in the display window, do not turn off the TV nor
change the TV programme position. When the TV indicator is not lit, the VCR
continues recording the programme even if you change the TV programme position
on the TV.
48
Basic Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Re co rd in g TV
p ro g ra m m e s
u sin g t h e
I/u
Sh o w Vie w syst e m
The ShowView system is the feature that
simplifies programming the VCR to
make timer recording. Just enter the
ShowView number listed in the TV
programme guide. The date, times, and
programme position of that programme
are set automatically. You can preset up
to eight programmes at a time.
CLEAR
1
4
7
2
5
8
0
3
6
9
Programme
number
buttons
Before you start…
• Check that the VCR clock is set to the
correct time and date.
• Insert a tape with its safety tab in
place. Make sure the tape is longer
than the total recording time.
TIMER
• Turn on your TV and set it to the
video channel.
• Set TIMER OPTIONS to SHOWVIEW
or VARIABLE in the OPTIONS-2
menu (see page 72).
>/./?//
OK
p STOP
continued
Basic Operations 49
Download from Www.Somanuals.com. All Manuals Search And Download.
Re co rd in g TV p ro g ra m m e s u sin g t h e Sh o w Vie w syst e m
(co n t in u e d )
TIMER
1
Press
TIMER.
TIMER METHOD
• When you set TIMER OPTIONS to
VARIABLE
STANDARD
SHOWVIEW
The TIMER METHOD menu appears
on the TV screen. Press >/ . to select
SHOWVIEW, then press OK.
SELECT
SET
:
: OK
EXIT : MENU
2 8 . 9 TUE
SHOWVIEW
• When you set TIMER OPTIONS to
SHOWVIEW
SHOWVIEW NO.
– – – – – – – – –
The SHOWVIEW menu appears on the
TV screen.
SET
:
0–9
EXIT : MENU
1
4
7
2
5
8
0
3
6
9
SHOWVIEW
2
Press the programme number buttons to
enter the ShowView number.
2 8 . 9 TUE
SHOWVIEW NO.
1 2 4 6 – – – – –
CLEAR
SET
CONFIRM : OK
CANCEL CLEAR
:
0–9
If you make a mistake, press CLEAR and
re-enter the correct number.
:
EXIT : MENU
50
Basic Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER
3
Press OK.
2 8 . 9 TUE
PLAY
OK
DATE
TIME
PROG.
3 5
The date, start and stop times,
programme position, tape speed, and
VPS/ PDC setting appear on the TV
screen.
TODAY
SP / LP
LIST
1 9 : 0 0 2 0 : 0 0
SP
VPS / PDC
OFF
SELECT
:
:
:
SET
CANCEL
CLEAR
• If “--” appears in the “PROG.”
(programme) column (this may
EXIT : MENU
happen for local broadcasts), you have to set the appropriate
programme position manually.
Press >/ . to select the desired programme position.
To record from a decoder or other source connected to the LINE-1
(TV) or LINE-2 IN (Scart) connector, press INPUT SELECT to
display “L1” or “L2.”
You will only have to do this operation once for the referred
channel. The VCR will then store your setting.
• When you have selected A (Austria), CH (Switzerland), or D
(Germany) with the country selection in the Auto Set Up
procedure, the VPS/ PDC function is automatically set to ON.
For details of the VPS/ PDC function, see “Timer recording with
VPS/ PDC signals” on page 52.
CLEAR
If the information is incorrect, press CLEAR to cancel the setting.
TIMER
4
If you want to change the date, tape
speed, and the VPS/ PDC function
setting:
2 8 . 9 TUE
PLAY
OK
DATE
TODAY
TIME
PROG.
3 5
1 9 : 0 0 2 0 : 0 0
SP / LP
LIST
SP
VPS / PDC
OFF
1 Press ?/ / to highlight the item
you want to change.
2 Press >/ . to reset it.
SELECT
:
:
:
SET
CANCEL
CLEAR
EXIT : MENU
• To record the same programme every
day or the same day every week, see “Daily/ weekly recording”
on page 52.
• To use the VPS/ PDC function, set VPS/ PDC to ON.
continued
Basic Operations 51
Download from Www.Somanuals.com. All Manuals Search And Download.
Re co rd in g TV p ro g ra m m e s u sin g t h e Sh o w Vie w syst e m
(co n t in u e d )
MENU
5
6
Press MENU to exit the menu.
Press I/ u to turn off the VCR.
The
indicator appears in the display window and the VCR
stands by for recording.
To stop recording
To stop the VCR while recording, press p STOP.
Daily/w eekly recording
In step 4 above, press . to select the recording pattern. Each time you press
., the indication changes as shown below. Press > to change the indication
in reverse order.
TODAY n SUN-SAT (Sunday to Saturday) n MON-SAT (Monday to Saturday)
n MON-FRI (Monday to Friday) n SAT (every Saturday) .....
n MON (every Monday) n SUN (every Sunday) n 1 month later
n (dates count dow n) n TOMORROW n TODAY
Timer recording w ith VPS/PDC signals
Some broadcast systems transmit VPS (Video Programme System) or PDC
(Programme Delivery Control) signals with their TV programmes. These
signals ensure that your timer recordings are made regardless of broadcast
delays, early starts, or broadcast interruptions (with the VPS or PDC
indicator in the display window lit).
To use the VPS/ PDC function, set VPS/ PDC to ON in step 4 above. You can
also use the VPS/ PDC function for a source connected to the LINE-1 (TV)
and LINE-2 IN (Scart) connectors.
52
Basic Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
To record satellite broadcasts
If you connect the satellite tuner and the VCR, you can record satellite
programmes.
1
2
Turn on the satellite tuner.
On the satellite tuner, select the satellite programme for which you
want to make a timer setting.
3
Keep the satellite tuner turned on until the VCR finishes recording the
satellite programme for which you have made a timer setting.
To use the VCR after setting the timer
To use the VCR before a timer recording begins, just press I/ u. The
indicator turns off and the VCR switches on. Remember to press I/ u to
reset the VCR after using the VCR.
You can also do the following tasks while the VCR is recording:
• Reset the counter.
• Display tape information on the TV screen.
• Check the timer settings.
• Watch another TV programme.
Tips
•
To set the programme position with a two digit number, press ? (ten’s digit)
button followed by the programme number button.
•
To set the programme position, you can also use the PROG +/ – or programme
number buttons.
•
•
To set the tape speed, you can also use the SP/ LP button.
When you are recording a programme in the SP mode and the remaining tape
becomes shorter than the recording time, the tape speed is automatically changed to
the LP mode. Note that some interference will appear on the picture at the point the
tape speed is changed. If you want to keep the same tape speed, set AUTO LONG
PLAY to OFF in the OPTIONS-1 menu (page 71).
•
To check, change, or cancel the programme setting, press ?/ / to choose LIST,
then press OK after step 4. For details, see step 3 in “Checking/ changing/
cancelling timer settings” (page 60).
Notes
•
If the VPS/ PDC signal is too weak or the broadcasting station failed to transmit
VPS/ PDC signals, the VCR will start recording at the set time without using the
VPS/ PDC function.
•
•
The
inserted.
indicator flashes in the display window when you press I/ u with no tape
When you set TIMER OPTIONS to STANDARD in the OPTIONS-2 menu, the
SHOWVIEW menu does not appear on the TV screen. Select SHOWVIEW or
VARIABLE.
Basic Operations 53
Download from Www.Somanuals.com. All Manuals Search And Download.
Se t t in g t h e t im e r
m a n u a lly
I/u
If the ShowView system is not available
in your area, follow the instructions
below to set the timer to record
programmes.
Before you start…
• Check that the VCR clock is set to the
correct time and date.
• Insert a tape with its safety tab in
place. Make sure the tape is longer
than the total recording time.
1
4
7
2
5
8
0
3
6
9
INPUT SELECT
• To record from a decoder, turn it on.
• Turn on your TV and set it to the
video channel.
• Set TIMER OPTIONS to STANDARD
or VARIABLE in the OPTIONS-2
menu (see page 72).
MENU
TIMER
>/./?//
OK
p STOP
TIMER
1
Press
TIMER.
TIMER METHOD
• When you set TIMER OPTIONS to
VARIABLE
STANDARD
SHOWVIEW
The TIMER METHOD menu appears
on the TV screen. Press >/ . to select
STANDARD, then press OK.
SELECT
SET
:
: OK
EXIT : MENU
2 8 . 9 TUE
TIMER
• When you set TIMER OPTIONS to
STANDARD
DATE
TIME
PROG.
– –
TODAY
SP / LP
LIST
– – : – – – – : – –
SP
VPS / PDC
OFF
The TIMER menu appears on the TV
screen.
SELECT
:
:
:
SET
CANCEL
CLEAR
EXIT : MENU
54
Basic Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER
2
Set the date, start and stop times,
programme position, tape speed, and
VPS/ PDC function:
2 8 . 9 TUE
PLAY
OK
DATE
TIME
PROG.
3 5
TODAY
SP / LP
LIST
1 9 : 0 0 2 0 : 0 0
SP
VPS / PDC
OFF
1 Press / to highlight each item in turn.
2 Press >/ . to set each item.
To correct a setting, press ? to return to
that setting and reset.
SELECT
:
:
:
SET
CANCEL
CLEAR
EXIT : MENU
• To record the same programme every day or the same day every
week, see “Daily/ weekly recording” on page 56.
• To use the VPS/ PDC function, set VPS/ PDC to ON. For details of
the VPS/ PDC function, see “Timer recording with VPS/ PDC
signals” on page 52.
INPUT SELECT
• To record from a decoder or other source connected to the
LINE-1 (TV) or LINE-2 IN (Scart) connector, press INPUT
SELECT to display “L1” or “L2” in the “PROG.” position.
MENU
3
4
Press MENU to exit the menu.
Press I/ u to turn off the VCR.
The
indicator appears in the display window and the VCR
stands by for recording.
To record from a decoder or other source, leave the connected
equipment switched on.
To stop recording
To stop the VCR while recording, press p STOP.
continued
Basic Operations 55
Download from Www.Somanuals.com. All Manuals Search And Download.
Se t t in g t h e t im e r m a n u a lly (co n t in u e d )
Daily/w eekly recording
In step 2 above, press . to select the recording pattern. Each time you press
., the indication changes as shown below. Press > to change the indication
in reverse order.
TODAY n SUN-SAT (Sunday to Saturday) n MON-SAT (Monday to Saturday)
n MON-FRI (Monday to Friday) n SAT (every Saturday) .....
n MON (every Monday) n SUN (every Sunday) n 1 month later
n (dates count dow n) n TOMORROW n TODAY
Tips
•
To set the programme position, you can also use the PROG +/ – or programme
number buttons.
•
•
To set the tape speed, you can also use the SP/ LP button.
When you are recording a programme in the SP mode and the remaining tape
becomes shorter than the recording time, the tape speed is automatically changed to
the LP mode. Note that some interference will appear on the picture at the point the
tape speed is changed. If you want to keep the same tape speed, set AUTO LONG
PLAY to OFF in the OPTIONS-1 menu (page 71).
•
Even if you set TIMER OPTIONS to SHOWVIEW in the OPTIONS-2 menu, you can
set the timer manually. Press MENU to select TIMER, then go to step 2.
Notes
•
•
•
When setting the timer with VPS/ PDC signals, enter the start and stop times
exactly as indicated in the TV programme guide, otherwise the VPS/ PDC function
won’t work.
If the VPS/ PDC signal is too weak or the broadcasting station failed to transmit
VPS/ PDC signals, the VCR will start recording at the set time without using the
VPS/ PDC function.
The
indicator flashes in the display window when you press I/ u with no tape
inserted.
56
Basic Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Operations
Pla yin g /se a rch in g
a t va rio u s sp e e d s
× 2
& SLOW
1
4
7
2
5
8
0
3
6
9
· PLAY
)# FF
03 REW
)# FF
03 REW
Playback options
Operation
View the picture during
fast-forward or rewind
During fast-forward, hold down )# FF. During rewind, hold
down 03 REW.
Play at high speed
•
•
During playback, press )# FF or 03 REW on the remote
commander.
During playback, hold down )# FF or 03 REW. When
you release the button, normal playback resumes.
continued
Additional Operations
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Pla yin g /se a rch in g a t va rio u s sp e e d s (co n t in u e d )
Playback options
Operation
Play at twice the normal
speed
During playback, press × 2.
Play in slow motion
Play frame by frame
During playback, press & SLOW.
During pause, press )# FF or 03 REW on the remote
commander. Hold down )# FF or 03 REW to play one
frame each second.
Rewind and start play
During stop, press · PLAY on the VCR while holding down
03 REW on the VCR.
To resume normal playback
Press · PLAY.
Tip
•
Adjust the picture using the TRACKING +/ – buttons if:
– Streaks appear while playing in slow motion.
– Bands appear at the top or bottom while pausing.
– The picture shakes while pausing.
To set tracking to the centre position, press both buttons (+/ –) at the same time.
Notes
•
•
The sound is muted during these operations.
In the LP mode, noise may appear or there may be no colour.
58 Additional Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Se t t in g t h e
re co rd in g
d u ra t io n t im e
r REC
After starting recording in the normal
way, you can have the VCR stop
recording automatically after a specified
duration.
1
2
While recording, press r REC.
The indicator appears in the display window.
SP VIDEO
OPC
Press r REC repeatedly to set the duration.
Each press advances the time in increments of 30 minutes.
Normal recording
0:30
1:00
5:30
6:00
The tape counter decreases minute by minute to 0:00, then the VCR
stops recording and turns off automatically.
To extend the duration
Press r REC repeatedly to set a new duration.
To cancel the duration
Press r REC repeatedly until the
indicator disappears and the VCR
returns to normal recording mode.
To stop recording
To stop the VCR while recording, press p STOP.
Note
•
You cannot display the current tape time in the display window when setting the
recording duration.
Additional Operations
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch e ckin g /
ch a n g in g /
I/u
ca n ce llin g t im e r
se t t in g s
Before you start…
CLEAR
• Turn on your TV and set it to the
video channel.
1
4
7
2
5
8
0
3
6
9
MENU
>/./?//
OK
1
2
3
Press I/ u to turn on the VCR.
Press MENU, then press >/ . to highlight LISTS and press OK.
TIMER LIST
Press >/ . to highlight TIMER LIST, then
press OK:
2 8 . 9 TUE
VPS
PDC
DATE
TODAY
3 0 . 9
TIME
PROG.
3 5
AAB
CDE
FGH
I J K
– –
1 9 : 0 0 2 0 : 0 0
2 0 : 0 0 2 1 : 0 0
1 0 : 0 0 1 1 : 3 0
1 4 : 0 0 1 5 : 0 0
SP
SP
LP
LP
LP
–
VPS
PDC
2 . 1 0
MON
–
FRI
• If you want to change or cancel a setting,
go on to the next step.
SUN
6 : 3 0
– : – –
– : – –
– : – –
7 : 0 0
– : – –
– : – –
– : – –
– – . – –
– – . – –
– – . – –
RETURN
– –
– –
–
–
SELECT
SET
:
• If you do not need to change or cancel
the settings, press MENU, then turn off
the VCR to return to recording standby.
: OK
:
CANCEL
CLEAR
EXIT : MENU
60 Additional Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER
4
Press >/ . to select the setting you want to
change or cancel, then press OK.
2 8 . 9 TUE
DATE
. 1 0
TIME
1 0 : 0 0 1 1 : 3 0
PROG.
CDE
2
SP / LP
LIST
LP
VPS / PDC
ON
The selected setting appears in the TIMER
menu.
SELECT
:
:
:
SET
CANCEL
CLEAR
EXIT : MENU
5
6
• To change the setting, press ?/ / to highlight the item you want to
change, and press >/ . to reset it.
• To cancel the setting, press CLEAR.
Press MENU.
If any settings remain, turn off the VCR to return to recording standby.
When the timer settings overlap
The programme that starts first has priority and the second programme
starts recording only after the first programme has finished. If the
programmes start at the same time, the programme listed first in the menu
has priority.
Programme 1
Programme 2
about 20 seconds
w ill be cut off
Programme 1
Programme 2
about 20 seconds w ill be cut off
Additional Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
61
Re co rd in g st e re o a n d b ilin g u a l
p ro g ra m m e s
In ZWEITON (Ge rm a n st e re o ) syst e m
This VCR automatically receives and records stereo and bilingual
programmes based on the ZWEITON system. When a stereo or bilingual
programme is received, the STEREO indicator appears in the display
window.
To select bilingual sound w hile recording
Press AUDIO MONITOR to select the sound you want.
To listen to
Main
On-screen display
MAIN
Display w indow
STEREO
Sub
SUB
STEREO
Main and sub
MAIN/ SUB
STEREO
In NICAM syst e m (SLV-SE70NP1/SE70NP2 o n ly)
This VCR receives and records stereo and bilingual programmes based on
the NICAM system (the NICAM indicator appears). When a stereo or
bilingual programme is received, the STEREO indicator appears in the
display window.
To record a NICAM programme, HIFI AUDIO in the OPTIONS-1 menu
should be set to NICAM (initial setting). To check the menu setting, see page
71 for details.
To select the sound w hile recording
Press AUDIO MONITOR to select the sound you want.
Stereo programme
To listen to
Stereo
On-screen display
STEREO
Display w indow
STEREO
Standard sound*
No indicator
No indicator
* Usually the mixed sound of left and right channels (monaural)
62 Additional Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Bilingual programme
To listen to
Main
On-screen display
MAIN
Display w indow
STEREO
Sub
SUB
STEREO
Main and sub
Standard sound*
MAIN/ SUB
No indicator
STEREO
No indicator
* Usually the main sound (monaural)
Se le ct in g t h e so u n d d u rin g p la yb a ck
Press AUDIO MONITOR to select the sound you want.
To listen to
On-screen display
Display w indow
Stereo/ main and sub
STEREO
STEREO
(left and right channels)
Left channel/ main
Right channel/ sub
Standard sound
LCH
STEREO
RCH
STEREO
No indicator
No indicator
Ho w so u n d is re co rd e d o n a vid e o t a p e
The VCR records sound onto two separate tracks. Hi-fi audio is recorded
onto the main track along with the picture. Monaural sound is recorded
onto the normal audio track along the edge of the tape.
Stereo
Usually mixed
Bilingual
left/right channels
Usually main sound
Normal audio track
(monaural)
Hi-fi audio track
(main track)
Stereo sound
(left/right channels)
Main (left channel)
Sub (right channel)
Notes
•
•
•
•
To listen to playback sounds in stereo, you must use the EURO-AV or AUDIO OUT
connections.
When you play a tape recorded in monaural, the sound is heard in monaural
regardless of the AUDIO MONITOR setting.
If the AUDIO MONITOR button does not function, check that AUDIO MIX in the
OPTIONS-1 menu is set to OFF (see page 71).
If HIFI AUDIO is set to STANDARD, the standard sound will be recorded on both
the hi-fi and normal audio tracks. Pressing AUDIO MONITOR will not change the
sound (SLV-SE70NP1/ SE70NP2 only).
Additional Operations
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Se a rch in g u sin g
t h e Sm a rt Se a rch
fu n ct io n
I/u
If you record multiple programmes on a
tape, use the Smart Search function to
see what has been recorded on your
tape. You can see information such as
date, time, and channel of programmes
recorded on a tape. You can also start
playback directly from the selected
programme using the SMART SEARCH
screen.
1
4
7
2
5
8
0
3
6
9
All programmes are listed on the screen,
regardless of how the programme was
recorded.
The data of the last tape inserted into the
VCR is automatically stored in memory.
If you want to recall the latest data
screen, select LATEST DATA in the
SMART SEARCH screen (see page 65).
SMART
SEARCH
Before you start…
>/./?//
OK
• Turn on your TV and set it to the
video channel.
1
2
3
After recording, press I/ u to turn on the VCR.
SMART SEARCH
DATE TIME
Press SMART SEARCH.
1 8 0 MIN.
PROG.
3 5
FGH
FGH
AAB
2 8 . 9
2 9 . 9
3 0 . 9
3 0 . 9
1 9 : 0 0 2 0 : 0 0
1 4 : 0 0 1 5 : 0 0
1 4 : 0 0 1 5 : 0 0
2 0 : 0 0 2 1 : 0 0
Press >/ ./ ?/ / to select the
programme you want to start viewing.
BLANK TIME
3 0 MIN.
SELECT
SET
:
: OK
EXIT
:
SMART SEARCH
1 8 0 MIN.
SMART SEARCH
4
Press OK.
The VCR starts searching, and playback
starts automatically from the beginning of
the selected programme.
64 Additional Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
To stop searching
Press p STOP.
To exit the SMART SEARCH screen
Press SMART SEARCH.
To record in a blank space
Blank space on the tape will appear as a blank row in the SMART SEARCH
screen. Select the blank row in step 3, then press OK. The VCR rewinds/
fast-forwards the tape to the beginning of the blank space, then stops. Start
recording.
To re ca ll t h e la t e st d a t a scre e n a ft e r yo u re m o ve t h e
t a p e
You can display the data of the last tape used to record a programme, even
after you have removed the tape.
If you reinsert the tape and record additional programmes, be sure to select
LATEST DATA. Otherwise, all of the data for the tape is deleted.
1
2
Reinsert the last tape that you used to record a programme.
SMART SEARCH
Press SMART SEARCH.
NO DATA
LATEST DATA
SELECT
SET
:
: OK
EXIT
:
SMART SEARCH
PROG.
SMART SEARCH
DATE TIME
3
4
Press >/ . to highlight LATEST DATA.
2 8 . 9
2 9 . 9
3 0 . 9
3 0 . 9
1 9 : 0 0 2 0 : 0 0
1 4 : 0 0 1 5 : 0 0
1 4 : 0 0 1 5 : 0 0
2 0 : 0 0 2 1 : 0 0
3 5
FGH
FGH
AAB
If you want to reset the latest data screen,
highlight NO DATA and press OK, then
record a programme.
NO DATA
LATEST DATA
SELECT
SET
:
: OK
EXIT
:
SMART SEARCH
Press OK.
The latest data stored in the VCR’s memory is displayed.
continued
Additional Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
65
Se a rch in g u sin g t h e Sm a rt Se a rch fu n ct io n (co n t in u e d )
Tips
•
•
You can store information for up to 24 programmes on a single list.
While recording, you can display the SMART SEARCH screen using the
SMART SEARCH button. If you decide to stop recording, press SMART SEARCH
to make the SMART SEARCH screen disappear first. Then press p STOP.
Notes
•
If you begin recording a programme “D” from the middle of a previously recorded
programme “A” and into another previously recorded programme “B,” the Smart
Search information for the second programme “B” which is recorded over is
deleted.
Originally recorded programmes
A
B
C
Recording the programme “D” over the programme “A” and “B”
A
D
C
•
•
•
You cannot use this function unless the clock is set.
Depending on the tape, the total or remaining time may not appear correctly.
When recording a short programme (less than 10 minutes in SP mode, or 20 minutes
in LP mode), the Smart Search function may not be available or the programme
information may not appear. Also, if you record a long programme directly after a
short programme, the Smart Search information for the short programme may be
deleted.
•
•
Blank space is measured from the end of the last recorded programme to the end of
the tape. However, if you eject the tape then make a new recording on the same
tape, the original recorded programme(s) is displayed as a blank space.
If no information is stored in the VCR’s memory, LATEST DATA does not appear in
the SMART SEARCH screen.
66 Additional Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Se a rch in g u sin g
t h e in d e x
fu n ct io n
The VCR marks the tape with an index
signal at the point where each recording
begins. Use these signals as references to
find a specific recording.
=/+
INDEX
SEARCH
1
2
3
1
2
Insert an indexed tape into the VCR.
Press =/ + INDEX SEARCH.
• To search ahead, press
INDEX
SEARCH
+ INDEX SEARCH.
• To search backwards, press
= INDEX SEARCH.
The VCR starts searching, and playback
starts automatically from that point.
To stop searching
Press p STOP.
Note
•
No index signal will be added when recording starts from recording pause.
However, an index signal will be marked if you change the programme position
during recording pause.
Additional Operations
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Ad ju st in g t h e p ict u re
Ad ju st in g t h e t ra ckin g
Although the VCR automatically adjusts the tracking when playing a tape
(the
indicator flashes in the display window, then goes off), distortion
may occur if the tape was recorded in poor condition. In this case, manually
adjust the tracking.
During playback, press TRACKING +/ – to
display the tracking meter. The distortion
should disappear as you press one of the two
buttons (the
indicator lights up). To resume
automatic tracking adjustments, eject the tape
and re-insert it.
TRACKING
Tracking meter
Ab o u t t h e Op t im u m Pict u re Co n t ro l (OPC) fu n ct io n
OPTIONS - 1
The Optimum Picture Control (OPC) function
OPC
EDIT
ON
automatically improves recording and playback
quality by adjusting the VCR to the condition of
the video heads and tape. To maintain better
picture quality, we recommend that you set OPC
to ON in the OPTIONS-1 menu (with the OPC
indicator in the display window lit). For details,
see page 71.
OFF
AUDIO MIX
HIFI AUDIO
AUTO LONG PLAY
TAPE LENGTH
RETURN
OFF
NICAM
OFF
E1 8 0
SELECT
SET
:
: OK
EXIT : MENU
OPC playback
The OPC function automatically works on all types of tapes, including rental
tapes and tapes that were not recorded with OPC.
OPC recording
Whenever you insert a tape and start recording for the first time, the VCR
adjusts to the tape using the OPC function (the OPC indicator flashes
rapidly). This adjustment is retained until the tape is ejected.
To deactivate the OPC function
Set OPC to OFF in the OPTIONS-1 menu. The OPC indicator in the display
window goes off.
68 Additional Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
To set tracking to the centre position, press the TRACKING + and – buttons at the
same time.
Notes
•
•
You can adjust the tracking for the NTSC-recorded tape but the tracking meter won’t
be displayed.
•
With the Auto Long Play function on, the OPC function will work only in SP mode.
If the tape speed automatically switches from SP to LP, the OPC function turns off.
If, however, the entire programme is recorded in LP mode, the OPC function will
work.
•
There is a delay of about ten seconds before the VCR actually starts recording while
the VCR analyses the tape. To avoid the delay, first set the VCR to recording pause
(the OPC indicator flashes slowly) and press r REC to have the VCR analyse the
tape (the OPC indicator flashes rapidly). After the OPC indicator stops flashing,
press P PAUSE to start recording immediately. If you want to start recording
quickly without using the OPC function, first set the VCR to recording pause (the
OPC indicator flashes slowly) and press P PAUSE to start recording.
Additional Operations
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a n g in g m e n u o p t io n s
OPTIONS
1
Press MENU, then select OPTIONS and
press OK.
OPTIONS - 1
OPTIONS - 2
RETURN
SELECT
SET
:
: OK
EXIT : MENU
2
Press >/ . to highlight OPTIONS-1 or OPTIONS-2, then press OK.
Example: SLV-SE70NP1/SE70NP2
OPTIONS - 1
OPTIONS - 2
OPC
EDIT
ON
DECODER / LINE2
TIMER OPTIONS
POWER SAVE
RF MODULATOR
TV DIRECT REC
RETURN
DECODER
VARIABLE
OFF
OFF
AUDIO MIX
OFF
HIFI AUDIO
NICAM
OFF
ON
AUTO LONG PLAY
TAPE LENGTH
RETURN
ON
E1 8 0
SELECT
SET
:
SELECT
SET
:
: OK
: OK
EXIT : MENU
EXIT : MENU
3
4
5
Press >/ . to select the option, then press OK.
Press >/ . to change the setting, then press OK.
Press MENU to return to the original screen.
70 Additional Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu choices
Initial settings are indicated in bold print.
OPTIONS-1
Menu option
Set this option to
•
•
ON to switch on the OPC (Optimum Picture Control)
function and improve picture quality.
OFF to switch off OPC.
OPC
EDIT
•
•
ON to minimize picture deterioration when editing.
OFF to turn off EDIT.
AUDIO MIX
•
ON to listen to the hi-fi and normal audio tracks at the
same time. The AUDIO MONITOR button will not
function.
•
OFF to listen to the hi-fi and normal audio tracks
separately. Select the sound using the AUDIO MONITOR
button.
For details, see page 63.
HIFI AUDIO
(SLV-SE70NP1/
SE70NP2 only)
•
•
NICAM to record NICAM broadcasts on the hi-fi audio
track.
STANDARD to record standard sound on the hi-fi audio
track.
For details, see page 62.
AUTO LONG PLAY
TAPE LENGTH
•
ON to change the timer recording tape speed automatically
to the LP mode when the remaining tape becomes shorter
than the recording time.
•
OFF to keep the set tape speed.
•
•
•
•
E180 to use an E-180 or shorter type tape.
E195 to use an E-195 type tape.
E240 to use an E-240 type tape.
E300 to use an E-300 type tape.
continued
Additional Operations
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a n g in g m e n u o p t io n s (co n t in u e d )
OPTIONS-2
Menu option
Set this option to
DECODER/ LINE2
•
•
DECODER to use the DECODER/ LINE-2 IN connector as
the PAY-TV/ Canal Plus decoder connector.
LINE2 to use the DECODER/ LINE-2 IN connector as the
line input connector.
TIMER OPTIONS
•
VARIABLE to display the TIMER METHOD menu for
selecting STANDARD or SHOWVIEW when pressing
TIMER button.
•
•
STANDARD to display the TIMER menu when pressing
the
SHOWVIEW to display the SHOWVIEW menu when
pressing the TIMER button.
For details, see pages 49 and 54.
TIMER button.
POWER SAVE
•
•
ON to turn off the indicators in the display window to
conserve the VCR power.
OFF to turn on the indicators in the display window while
the VCR is standing by.
RF MODULATOR
•
•
ON if you connect the VCR to your TV using only the
aerial cable.
OFF if you connect the VCR to your TV using the EURO-
AV cable.
TV DIRECT REC
•
•
ON to activate the TV Direct Rec function.
OFF to deactivate it.
Notes
•
When you set a timer recording, the indicators in the display window remain on,
even though POWER SAVE is set to ON.
•
With the EDIT option ON, the OPC function does not work.
72 Additional Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Ed it in g w it h a n o t h e r VCR
Ho w t o co n n e ct t o re co rd o n t h is VCR
This VCR (Recorder)
TV
DECODER/
… LINE-2 IN
Other VCR (Player)
EURO-AV
(Scart)
VMC-2121HG EURO-AV cable (not supplied)
: Signal flow
Tip
You can also use the LINE-1 (TV) connector instead.
Notes
•
•
When you connect another VCR to the LINE-2 IN (Scart) connector, set DECODER/
LINE2 to LINE2 in the OPTIONS-2 menu.
•
If the other VCR doesn’t have a EURO-AV (Scart) connector, use the VMC-2106HG
cable instead and connect the cable to the line out jacks of the other VCR.
continued
Additional Operations
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Ed it in g w it h a n o t h e r VCR (co n t in u e d )
r REC
Op e ra t io n
(w h e n re co rd in g o n t h is VCR)
Before you start editing
• Turn on your TV and set it to the
video channel.
P PAUSE
• Press INPUT SELECT to display “L2”
(or “L1”) in the display window.
• Press SP/ LP to select the tape speed, SP or LP.
• On this VCR, set EDIT to ON in the OPTIONS-1 menu. If the other
VCR has a similar function, turn it on also.
1
Insert a source tape with its safety tab removed into the other
(playback) VCR. Search for the point to start playback and set it to
playback pause.
2
Insert a tape with its safety tab in place into this (recording) VCR.
Search for the point to start recording and press P PAUSE.
3
4
Press r REC on this VCR to set it to recording pause.
To start editing, press the P PAUSE buttons on both VCRs at the same
time.
To stop editing
Press the p STOP buttons on both VCRs.
Tip
•
To cut out unwanted scenes while editing, press P PAUSE on this VCR when an
unwanted scene begins. When it ends, press P PAUSE again to resume recording.
Note
If you start editing following the procedure above, the VCR won’t start recording
•
with the OPC function. To record a tape with the OPC function, press r REC again
during recording pause in step 3 so the VCR analyses the tape. Then, when you
start editing in step 4, press P PAUSE after the OPC indicator stops flashing. If you
press P PAUSE before the OPC indicator stops flashing, the OPC function is
cancelled.
74 Additional Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
Tro u b le sh o o t in g
If you have any questions or pr oblems not cover ed below , please consult your near est
Sony ser vice facility .
Symptom
Remedy
The I/u ON/ STANDBY switch
•
Connect the mains lead to the mains secur ely.
doesnot function.
The power is turned on but the
VCR does not operate.
•
Moistur e condensation occurs. T urn the power of f,
unplug the mains lead and leave the VCR to dry for
over thr ee hours.
The clock has stopped and
“–:– –” lights in the display
window .
•
The clock stops if the VCR is disconnected fr om the
mains for mor e than one hour . Reset the clock (and
timer).
The playback pictur e does not
appear on the TV scr een.
•
•
Make sur e the TV is set to the video channel. If you
are using a monitor , set it to video input.
If the VCR is connected to the TV only with the aerial
cable, make sur e that RF MODULATOR in the
OPTIONS-2 menu is set to ON.
The pictur e is not clear .
•
•
Adjust the tracking with the TRACKING +/ – buttons.
The video heads ar e dirty (see below). Clean the video
heads using the Sony T -25CLD, E-25CLDR, or
T-25CLW video head cleaning cassette. If these
cleaning cassettes ar e not available in your ar ea, have
the heads cleaned at your near est Sony ser vice facility
(a standar d ser vice char ge will be r equired). Do not
use a commer cially available liquid type cleaning
cassette other than Sony’s, as it may damage the video
heads.
•
The video heads may have to be r eplaced. Consult
your local Sony ser vice facility for mor e infor mation.
Symptoms caused by contaminated video heads
• Normal picture
• Rough picture
• Unclear picture
• No picture (or
black & w hite
screen appears)
terminal
initial
contamination
continued
Additional Information 75
Download from Www.Somanuals.com. All Manuals Search And Download.
Tro u b le sh o o t in g (co n t in u e d )
Symptom
Remedy
The pictur e rolls ver tically
during pictur e sear ch.
•
Adjust the ver tical hold contr ol on the TV or monitor .
The pictur e has no sound.
•
•
The tape is defective.
If you made A/ V connections, check the audio cable
connection.
The sound is unstable or has an
echo.
•
When you play a tape with the same sound r ecor ded
on both the hi-fi and nor mal sound tracks, make sur e
AUDIO MIX in the OPTIONS-1 menu is set to OFF.
No TV programme appears on
the TV screen.
•
•
Make sur e the TV is set to the video channel. If you
are using a monitor , set it to video input.
If the VCR is connected to the TV using only the aerial
cable, make sur e that RF MODULATOR in the
OPTIONS-2 menu is set to ON.
•
Select the cor rect sour ce with the INPUT SELECT
button. Select a pr ogramme position when r ecording
TV programmes; select “L1” or “L2” when r ecor ding
from other equipment.
TV reception is poor .
•
•
Adjust the TV aerial.
The tape starts playing as soon
as it is inserted.
The safety tab has been r emoved. To recor d on this
tape, cover the tab hole.
The tape is ejected when you
press r REC.
•
•
Check that the safety tab has not been r
emoved.
Nothing happens when you
Make sur e the tape is not at its end.
press r REC.
The timer does not operate.
•
•
•
•
•
Check that the clock is set.
Make sur e a tape has been inser ted.
Check that the safety tab has not been r
Make sur e the tape is not at its end.
Make sur e a pr ogramme has been set for timer
recording.
emoved.
•
Make sur e your timer settings have not alr eady passed
the cur rent time.
•
•
•
Check that the decoder is turned on.
Check that the satellite tuner is turned on.
The clock stops if the VCR is disconnected fr om the
mains for mor e than one hour . Reset the clock and
timer.
The SHOWVIEW menu or the
TIMER menu does not appear .
•
Check that TIMER OPTIONS in the OPTIONS-2 menu
is set cor rectly.
76 Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
A tape cannot be inserted.
•
Check that a tape isn’ t alr eady in the tape
compartment.
The remote commander does
not function.
•
•
•
Make sur e you ar e pointing the r emote commander at
the r emote sensor on the VCR.
Replace all the batteries in the r emote commander with
new ones if they ar e weak.
Make sur e the TV / VIDEO remote contr ol switch is
set cor rectly.
You cannot watch or r ecor d
PAY-TV/ Canal Plus
programmes.
•
•
Check that the decoder is connected cor rectly.
Check that the OPTIONS-2 menu and the TUNER
menu ar e set cor rectly.
For details, see page 36.
“L2” does not appear in the
display window .
•
Check that DECODER/ LINE2 in the OPTION-2 menu
is set to LINE2.
The SMARTLINK function
does not work.
•
Check that your TV complies with SMAR TLINK,
MEGALOGIC, EASYLINK, Q-Link, or EURO VIEW
LIN K.
•
Make sur e you use the optional EURO-A V cable to
connect the VCR and your TV .
•
•
Make sur e the EURO-AV cable is connected secur ely.
The tracking meter does not
appear on the TV scr een.
The recor ding condition of the tape is ver y poor and
tracking cannot be adjusted.
•
•
The tracking meter does not appear when playing back
an NTSC-recor ded tape.
You cannot contr ol other TVs.
The VCR needs to be cleaned.
Set your TV’s code number . The code number may
change when you r eplace the batteries of the r emote
commander .
•
Clean the cabinet, panel and contr ols with a dr y, soft
cloth, or a soft cloth slightly moistened with a mild
deter gent solution. Do not use any type of solvent,
such as alcohol or benzine.
Additional Information 77
Download from Www.Somanuals.com. All Manuals Search And Download.
Sp e cifica t io n s
Syst e m
Ge n e ra l
Channel coverage
PAL (B/ G)
Power requirements
220 – 240 V AC, 50 Hz
Power consumption
22 W
VHF E2 to E12
VHF Italian channel A to H
UHF E21 to E69
CATV S01 to S05, S1 to S20
HYPER S21 to S41
Operating temperature
5°C to 40°C
Storage temperature
–20°C to 60°C
RF output signal
UHF channels 21 to 69
Aerial out
Dimensions
Approx. 430 × 100 × 314 mm (w/ h/ d)
including projecting parts and controls
Mass
75-ohm asymmetrical aerial socket
In p u t s a n d o u t p u t s
: LINE-1 (TV)
Approx. 4.5 kg
Su p p lie d a cce sso rie s
21-pin
Video input: pin 20
Remote commander (1)
R6 (size AA) batteries (2)
Aerial cable (1)
Audio input: pins 2 and 6
Video output: pin 19
Audio output: pins 1 and 3
DECODER/ … LINE-2 IN
21-pin
Design and specifications are subject to change
without notice.
Video input: pin 20
Audio input: pins 2 and 6
AUDIO OUT
Phono jack (2)
Rated output level: 327 mVrms
Load impedance: 47 kilohms
Output impedance: less than 10 kilohms
78 Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
In d e x t o p a rt s a n d co n t ro ls
Refer to the pages indicated in par entheses ( ) for details.
Fro n t p a n e l
1 I/u ON/ STANDBY switch/
8 pSTOP button (42, 74)
indicator (14)
9 PPAUSE button (42, 74)
2 Tape compar tment
!º PROGRAM/ TRACKIN G +/ –
3 § EJECT button (42)
buttons (17, 58, 68)
4 03 REW (rewind) button (42, 57)
5 ·PLAY button (42, 58)
!¡ AUTO SET UP/
RF (Radio Frequency) CHANNEL
button (14, 16)
6 )# FF (fast-for ward) button (42,
!™ Remote sensor (5)
57)
7 rREC (recor d) button (45, 59, 74)
continued
Additional Information 79
Download from Www.Somanuals.com. All Manuals Search And Download.
In d e x t o p a rt s a n d co n t ro ls (co n t in u e d )
Disp la y w in d o w
STEREO SP VIDEO VPS SMARTLINK
NICAM LP
EP
PDC OPC
TV
1 Timer indicator (52, 55)
8 SMARTLINK indicator (11)
9 TV indicator (48)
2 NICAM indicator (SLV-SE70NP1/
SE70NP2 only) (62)
0 Tracking indicator (68)
3 STEREO indicator (62)
4 Tape speed indicators (45)
5 VIDEO indicator (11, 46)
!¡ Time counter/ clock/ line/
programme position indicator (42,
45, 74)
!™ Remaining time indicator (46)
6 VPS (Video Programme System)/
PDC (Programme Deliver y Control)
indicator (52)
!£ Tape/ recor ding indicator (45)
7 OPC (Optimum Picture Contr ol)
indicator (68)
80 Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Re a r p a n e l
1 Mains lead (9, 10)
5 DECODER/ … LINE-2 IN
DECODEUR/ … ENTREE LIGNE-2
connector (13, 36, 73)
2 AERIAL IN
ANTENNE ENTREE connector (9,
10)
6 : LINE-1 (TV)
: LIGNE-1 (TV) connector (11, 36)
3 AERIAL OUT
ANTENNE SORTIE connector (9,
10)
7 AUDIO OUT R (right)/ L (left)
SORTIE AUDIO D/ G jacks (13)
4 NTSC PB (Play Back) switch (42)
continued
Additional Information 81
Download from Www.Somanuals.com. All Manuals Search And Download.
In d e x t o p a rt s a n d co n t ro ls (co n t in u e d )
Re m o t e co m m a n d e r
1 6 EJECT button (42)
2 WIDE button ( for TV) (7)
3 AUDIO MONITOR button (62)
4 ×2button*(58)
5 & SLOW button* (58)
6 SP (Standar d Play)/ LP (Long Play)
button (45)
7
DISPLAY button (46)
8 ?(ten’s digit) button (6, 47)
9 . (volume) +/ – buttons (for TV) (6)
0 r REC (recor d) button (45, 59)
!¡ MENU button (19, 60)
1
4
7
2
5
8
0
3
6
9
!™ P PAUSE/> button (19, 42)
p STOP/. button (19, 42)
03 REW (rewind)/ ? button
(42, 57)
)# FF (fast-for ward)//button
(42, 57)
· PLAY/ OK button (19, 42)
* FASTEXT buttons ( for TV)
82 Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
!£ TV / VIDEO ermote contr ol switch
(5)
!¢ I/u (on/ standby) switch (6, 52)
!∞ COUNTER/ REMAIN button (46)
V(Teletext) button (for TV) (7)
!§ ; TV power on/ TV mode select
button (for TV) (7)
!¶ =/+ INDEX SEARCH
buttons*(67)
!• CLEAR button (42, 50, 61)
1
4
7
2
5
8
0
3
6
9
!ª … TV/ VIDEO button (6, 11, 46)
@º Programme number buttons (6, 47)
@¡ INPUT SELECT button (45, 55, 74)
@™ PROG (programme) +/ – buttons (6,
27, 45)
√/◊Teletext page access buttons
(for TV) (7)
@£
TIMER button (50, 54)
@¢ SMART SEARCH button (64)
* FASTEXT buttons ( for TV)
Additional Information 83
Download from Www.Somanuals.com. All Manuals Search And Download.
In d e x
A, B
L
S
Adjusting
Language selecting 24
LP mode 45
Safety tab 46
Searching
picture 29, 68
tracking 68
at various speeds 57
M
Aerial hookup
AFT (Auto Fine Tuning) 29
Audio track 63
Auto Clock Set 22
Auto Set Up 16
Auto Long Play 71
9
using the index
function 67
using the Smart Search
function 64
Monaural 62
Monitoring
during playback 63
during recording 62
ShowView
recording 49
SMARTLINK
Automatic Power Off 12
One Touch Menu 12
One Touch Play 12, 43
One Touch Timer 12
Preset Download 11
TV Direct Rec 12, 48
Smart Search 64
N
C
NICAM broadcasts 62
Normal audio track 63
Canal Plus 36
Changing the programme
position 30
Changing the station name 32
Cleaning the video heads 75
Clock setting 19
O
OPC (Optimum Picture
Control) 68
Optional setting 70
SP mode 45
Stereo 62
Colour system
compatible colour
P, Q
PAY-TV 36
PDC (Programme Delivery
Control) 52
Picture adjustment. See
systems
setting 42
Connecting
2
T, U
Timer setting 54
cancelling 60
changing 60
checking 60
the VCR and your TV
to a satellite tuner 13
to a stereo system 13
9
Adjusting
Playback 41
to a TV with a EURO-AV
connector 10
Counter 42
at various speeds 57
frame-by-frame 58
selecting the sound 63
slow motion 58
daily/ weekly
recording 52, 56
using the ShowView
system 49
D
Tracking adjustment. See
Adjusting
Power save 72
Presetting channels 26
Disabling the programme
position 34
V, W, X, Y
Dubbing. See Editing
R
VPS (Video Programme
System) 52
Recording 44
E, F, G
bilingual
programmes 62
saving 46
stereo programmes 62
timer setting 54
Editing 73
EP mode 43
EURO-AV connection
10
Z
ZWEITON broadcasts 62
using the ShowView
system 49
what you watching on the
TV 48
H
Hi-fi audio track 63
I, J, K
Index search 67
while watching another
programme 46
RF channel 14
Sony Corporation Printed in France
Download from Www.Somanuals.com. All Manuals Search And Download.
|