3-062-331-12 (1)
Video Cassette
Recorder
Operating Instructions
The SmartFile function in this model meets the requirements of EU, EFTA,
Central and Eastern Europe
PAL NTSC 4.43
SLV-SF950N
Chlorine free paper
© 2000 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
4
5
9
Step 1 : Unpacking
Step 2 : Setting up the remote commander
Step 3 : Connecting the VCR
16 Step 4 : Tuning your TV to the VCR
26 Presetting channels
30 Setting/changing the station names
36 Setting the PAY-TV/Canal Plus decoder
Basic Operations
41 Playing a tape
44 Recording TV programmes
76 Recording using the SmartFile
function
ShowView system
81 Selecting and playing a programme
82 Checking the contents of a tape
84 Labelling a recorded programme and
56 Playing/searching at various speeds
tape
recorded tape in the SmartFile label
94 Protecting a recorded programme
61 Checking/changing/cancelling timer
96 Erasing the data of an unwanted
settings
programme
63 Recording stereo and bilingual
Additional Information
98 Troubleshooting
104 Specifications
programmes
65 Searching using the index function
66 Adjusting the picture
105 Index to parts and controls
110 Menu chart
Back cover
68 Changing menu options
Editing
71 Connecting to a VCR or stereo
Index
system
73 Basic Editing
Table of contents 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2 : Setting up the remote commander
Inserting the batteries
Insert two R6 (size AA) batteries
by matching the + and – on the
batteries to the diagram inside the
battery compartment.
Insert the negative (–) end first,
then push in and down until the
positive (+) end clicks into
position.
Using the remote commander
You can use this remote
commander to operate this VCR
and a Sony TV. Buttons on the
remote commander marked with a
dot (•) can be used to operate your
Sony TV. If the TV does not have
Remote sensor
g
the
symbol near the remote
sensor, this remote commander
will not operate the TV.
[TV] / [VIDEO]
1
2
3
To operate
the VCR
Set [TV] / [VIDEO] to
[VIDEO] and point at the remote sensor on the VCR
a Sony TV
[TV] and point at the remote sensor on the TV
continued
Setting up the remote commander 5
Download from Www.Somanuals.com. All Manuals Search And Download.
?/1
/
WIDE
AUDIO MONITOR
a
FASTEXT buttons
DISPLAY
t TV/VIDEO
1
4
7
2
5
8
0
3
6
9
Programme
number buttons
–/– –
PROG +/–
c/C
2 +/–
TV control buttons
To
Press
Set the TV to standby mode
Select an input source aerial in or line in
Select the TV’s programme position
?/1
t TV/VIDEO
Programme number buttons,
–/– –, PROG +/–
Adjust the TV’s volume
Switch to TV (Teletext off)
Switch to Teletext
2 +/–
a (TV)
/ (Teletext)
AUDIO MONITOR
FASTEXT buttons
Select the sound
Use FASTEXT
6
Setting up the remote commander
Download from Www.Somanuals.com. All Manuals Search And Download.
To
Press
DISPLAY
c/C
Call up the on-screen display
Change the Teletext page
Switch to/from wide mode of a Sony wide TV (For other WIDE
manufactures’ wide TVs, see “Controlling other TVs with
the remote commander”.)
Notes
•
•
With normal use, the batteries should last about three to six months.
If you do not use the remote commander for an extended period of time, remove the batteries
to avoid possible damage from battery leakage.
•
•
•
Do not use a new battery with an old one together.
Do not use different types of batteries together.
Some buttons may not work with certain Sony TVs.
Controlling other TVs with the remote commander
The remote commander is preprogrammed to control non-Sony TVs. If your TV is
listed in the table below, set the appropriate manufacturer’s code number.
Set TV/VIDEO at the top of the remote commander to TV.
1
Hold down ?/1, and enter your TV’s code number(s) using the programme
2 number buttons.Then release ?/1.
Now you can use the following TV control buttons to control your TV:
?/1, TV/VIDEO, programme number buttons, –/– – (ten’s digit), PROG +/–,
2 +/–, a (TV), / (Teletext), FASTEXT buttons, WIDE*, MENU*, M*/m*/<*/
,*, and OK*.
* These buttons may not work with all TVs.
Tip
•
When you set your TV’s code number correctly while the TV is turned on, the TV turns off
automatically.
continued
Setting up the remote commander 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until you find
the one that works with your TV.
To switch to wide mode, see the footnotes below this table for the applicable code
numbers.
Manufacturer
Sony
Code number
Manufacturer
NEC
Code number
01*1, 02, 03, 04, 05
66
15, 16, 69*3
Nokia
Aiwa
32
Akai
68
Nordmende
Orion
35, 42
Blaupunkt
Brionvega
C.G.M
Colonad
Dual
10, 21
47, 48
17*1, 49
40
Panasonic
Philips
06*1, 07*1, 08*1
09
03
Phonola
Pioneer
18, 19
26
44
Emerson
Fenner
Ferguson
Goldstar
Grundig
Hitachi
Hyper
03, 04
Saba
12, 13
22, 23
25
30, 31
Samsung
Sanyo
52
03, 04, 17
Schneider
Seleco
46
10*1, 11*1
14
24
Sharp
29
31
Siemens
Sinudyne
TEAC
39
Inno-Hit
Irradio
41
37
20
67
15, 16, 69*3
Telefunken
Thomson
Toshiba
36
ITT
43*2
38
JVC
33
Loewe
45
27*1, 28*1, 50*1, 51*1
09
White Westinghouse
34
Mitsubishi
Mivar
*1
Press WIDE to switch to the wide picture mode you want.
Press WIDE, then press 2 +/– to select the wide picture mode you want.
Press WIDE. The menu appears on the TV screen.Then, press M/m/</, to select the wide
*2
*3
picture you want and press OK.
Notes
•
If the TV uses a different remote control system from the one programmed to work with the
VCR, you cannot control your TV with the remote commander.
•
•
If you enter a new code number, the code number previously entered will be erased.
If you remove the batteries of the remote commander for more than a few minutes, the code
number may be reset to 01 (Sony). In this case, reset the appropriate code number.
8
Setting up the remote commander
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3 : Connecting the VCR
We recommend connecting your VCR to your TV using a Scart (EURO-
AV) cable. You must still connect your VCR to your TV with an aerial
cable as well.
If you use the Scart (EURO-AV) cable for connecting, you will improve
the picture and sound quality playback of your VCR and make the set-
ting up easier.
•
•
•
Connection to TV with an aerial cable only, see page 12.
Connection to TV and Set-Top Box, see page 13.
Connection to TV and decoder, see page 36.
Connection to your TV with a Scart (EURO-AV) connector
AERIAL IN
i LINE-1 AERIAL OUT
(TV)
Mains lead
to mains
AERIAL IN
Aerial cable (supplied)
Scart
(EURO-AV)
Scart cable (not supplied)
: Signal flow
Disconnect the aerial cable from your
TV and connect it to AERIAL IN on
the rear panel of the VCR.
1
AERIAL
ANTENNE
IN
ENTREE
OUT
SORTIE
Connect AERIAL OUT of the VCR
and the aerial input of your TV using
the supplied aerial cable.
AERIAL
2
ANTENNE
IN
ENTREE
OUT
SORTIE
continued
Connecting the VCR 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect LINE-1 (TV) on the VCR
and the Scart (EURO-AV) connector
on the TV with the optional Scart
cable.
(
)
LINE-1 TV
(
)
LIGNE-1 TV
3
4
This connection improves picture and
sound quality.Whenever you want to
watch the VCR picture, press t TV/
VIDEO to display the VIDEO
indicator in the display window.
Connect the mains lead to the mains.
You can now tune your TV to the VCR, see page 18.
Notes
•
If the TV is connected to the LINE-1 (TV) connector, setting the RF channel to OFF is
recommended (see page 18) . In the OFF position, only the signal from the aerial is output
through the AERIAL OUT connector.
•
For correct SmartLink connection, please refer to your TV’s instruction manual.
10 Connecting the VCR
Download from Www.Somanuals.com. All Manuals Search And Download.
About the SMARTLINK features
If the connected TV complies with
SMARTLINK, NexTView Link,
MEGALOGIC*1, EASYLINK/
CinemaLink*2, Q-Link*3 or T-V
LINK*,you can use the
OPC
VIDEO
P
H
indicator appears in the VCR’s display window when you turn on the TV).You can enjoy the
following SMARTLINK features.
• Preset Download
You can download your TV tuner preset data to this VCR and tune the VCR according to that
data in Auto Set Up.This greatly simplifies the Auto Set Up procedure. Be careful not to
disconnect the cables or exit the Auto Set Up function during the procedure.
See “Setting up the VCR with the Auto Set Up function” on page 19.
• TV Direct Rec
You can easily record what you are watching on the TV (other than tapes being played on this
VCR). For details, see “Recording what you are watching on the TV (TV Direct Rec)” on
page 47.
• One Touch Play
With One Touch Play, you can start playback automatically without turning on the TV. For
details, see “Starting playback automatically with one button (One Touch Play)” on page 43.
• One Touch Menu
You can turn on the VCR and TV, set the TV to the video channel, and display the VCR’s on-
screen display automatically by pressing MENU on the remote commander.
• One Touch Timer
You can turn on the VCR and TV, set the TV to the video channel, and display the timer
recording menu (the TIMER METHOD menu, the TIMER menu or the SHOWVIEW menu)
automatically by pressing
TIMER on the remote commander. You can set which timer
recording menu is displayed using TIMER OPTIONS in the OTHER OPTIONS menu (see
page 70).
• Automatic Power off
You can have the VCR turn off automatically, if the VCR is not used for about 1 minute, after
you turn off the TV.
• NexTView Download
You can easily set the timer by using the NexTView Download function on your TV. Please
refer to your TV’s instruction manual.
*1
“MEGALOGIC” is a registered trademark of Grundig Corporation.
“EASYLINK/CinemaLink” is a trademark of Philips Corporation.
“Q-Link” is a trademark of Panasonic Corporation.
“T-V LINK” is a trademark of JVC Corporation.
*2
*3
*4
Note
•
Not all TVs respond to the functions above.
continued
Connecting the VCR 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection to your TV with an aerial cable only
AERIAL IN
AERIAL OUT
Mains lead
AERIAL IN
to mains
Aerial cable (supplied)
: Signal flow
Disconnect the aerial cable from your
TV and connect it to AERIAL IN on
the rear panel of the VCR.
1
2
3
AERIAL
ANTENNE
IN
ENTREE
OUT
SORTIE
Connect AERIAL OUT of the VCR
and the aerial input of your TV using
the supplied aerial cable.
AERIAL
ANTENNE
IN
ENTREE
OUT
SORTIE
Connect the mains lead to the mains.
You can now tune your TV to the VCR, see page 16.
12 Connecting the VCR
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection to your TV and Set-Top Box (STB)
If you don’t use a STB, skip to page 16.
The illustration below shows an example of connecting the STB to LINE-3 IN.
Scart cable (supplied with Set-
Top Box)
Scart
(EURO-AV)
t LINE-3 IN
Set-Top
Box
AERIAL
IN
i LINE-1
(TV)
AERIAL
OUT
Aerial cable (supplied)
Scart
(EURO-AV)
Scart cable (not supplied)
:Signal flow
You can watch programmes from the Set-Top Box connected to this VCR on your TV
even when the VCR is turned off using the Line Through function. When you turn on
the STB, this VCR automatically sends the signal from the STB to the TV without
turning itself on
Connect the STB to the DECODER/LINE-3IN connector as shown above.
1
Set DECODER/LINE-3 to LINE-3 in the OTHER OPTIONS menu.
2
Set POWER SAVE to OFF in the OTHER OPTIONS menu.
3
Turn off the VCR.
4
To watch a programme from the STB, turn on the STB and your TV.
Note
•
You cannot watch programmes from your STB on the TV while recording unless you record
a programme from your STB.
continued
Connecting the VCR 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional connections
To a stereo system
You can improve sound quality by
connecting a stereo system to the AUDIO
OUT R/L jacks as shown on the right.
AUDIO OUT
R/L
LINE IN
Audio cable (not supplied)
To a TV that has phono type audio/
video input jacks (only if you don’t
connect the VCR and your TV using a
Scart connector)
This additional connection improves picture
and sound quality. Connect the TV as shown
on the right using a commercially available
connecting cable like the Sony VMC-810. If
your TV has only one audio input jack, use a
connecting cable like the Sony VMC-
910MS.
AUDIO OUT
LINE IN
R/L
VMC-810 cable (not supplied)
Connecting the VCR 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4 : Tuning your TV to the VCR
If you have connected the VCR to your TV using the Scart cable, skip to page 18.
If you have connected the VCR to your TV with an aerial
cable only
?
/1
RF CHANNEL
g
PROGRAM +/–
•
Turn on your TV and press ?/1 (on/standby) to turn on the VCR.
1
2
Pull down the drop down panel.
Press briefly RF CHANNEL on the VCR.
AUTO SET UP
RF CHANNEL
The factory-preset RF (Radio Frequency) channel appears in the display
window.
.
SMARTLINK
PDC
H
M
S
Turn on your TV and select an unused programme position for the VCR
picture (for ex. programme position "0").
3
This programme position will be referred to as the video channel (for
watching your VCR on the TV) after tuning is completed.
16 Tuning your TV to the VCR
Download from Www.Somanuals.com. All Manuals Search And Download.
Press RF CHANNEL.
AUTO SET UP
RF CHANNEL
4
The TV system appears in the display window.
SMARTLINK
C
PDC
H
M
S
Press PROGRAM +/- (repeatedly) to select the correct TV system. If you
watch the system B/G, select "G". If you watch the system D/K, select "K".
5
6
SMARTLINK
PDC
H
M
S
Tune in the programme position you have
selected (for ex. programme position "0")
until the picture on the right appears
SONY VIDEO CASSETTE RECORDER
clearly on the TV screen (background must
be green).
Refer to your TV manual for tuning
instructions.
If the picture does not appear clearly, see
“To obtain a clear picture from the VCR”
below.
Press RF CHANNEL.
AUTO SET UP
RF CHANNEL
7
You have now tuned your TV to the VCR. From now on, whenever you
want to play a tape, set the TV to the video channel (for ex. programme
position "0").
To check if the TV tuning is correct
Set the TV to the video channel (for ex. programma position "0") and press
PROGRAM +/– on the VCR. If the TV screen changes to a different programme each
time you press PROGRAM +/–, the TV tuning is correct.
To obtain a clear picture from the VCR
If the picture does not appear clearly in step 6 above, go to step 7 to finish this
procedure once. Then start from step 2. After pressing RF CHANNEL in step 2 to
display the RF CHANNEL, press PROGRAM +/–, so that another RF channel
appears.Then tune the TV to the new RF channel until a clear picture appears.
continued
Tuning your TV to the VCR 17
Download from Www.Somanuals.com. All Manuals Search And Download.
If you have connected your VCR to the TV with a Scart
(EURO-AV) connector and an aerial cable as well
In order to avoid any interferences with existing broadcasts, we recom-
mend you to set RF channel to the OFF position.
RF CHANNEL
g
PROGRAM +/–
•
Turn on your TV and press ?/1 (on/standby) to turn on the VCR.
1
2
Pull down the drop down panel.
Press briefly RF CHANNEL on the VCR.
AUTO SET UP
The factory-preset RF (Radio Frequency) channel appears in the display
window..
RF CHANNEL
SMARTLINK
PDC
H
M
S
Press PROGRAM +/- until the OFF indication appears in the display
window. The RF channel is then switched off.
-
PROGRAM +
TRACKING
3
SMARTLINK
PDC
H
M
S
The picture shown below appears clearly on the TV screen (background
must be green).
SONY VIDEO CASSETTE RECORDER
Press RF CHANNEL.You can now set the VCR with the Auto Set Up
function (see page 19).
AUTO SET UP
RF CHANNEL
4
Note
•
If in step 3 the green screen does not appear, select the "AV/EXTERNAL" source on your TV
(please refer to your TV instruction manual).
18 Tuning your TV to the VCR
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 5 : Setting up the VCR with the Auto
Set Up function
Before using the VCR for the first time, set up the VCR using the Auto Set Up
function.With this function, you can set the language for the on-screen display, TV
channels, guide channels for the ShowView system, and VCR clock automatically.
Before you start ...
•
Turn on the STB if it is connected to the VCR only by the aerial cable and not to the Scart
cable.
AUTO SET UP
g
PROGRAM +/–
Hold down AUTO SET UP on the VCR for more than 3 seconds.
1
2
AUTO SET UP
RF CHANNEL
The VCR automatically turns on, and the country abbreviation appears in
the display window.
AUTO ST UP
SMARTLINK
C
H
M
S
Press PROGRAM +/– to highlight the abbreviation of your country.
For some countries, there is a selection of languages to choose from.
The abbreviations of the countries and languages are as follows :
-
PROGRAM +
TRACKING
continued
Setting up the VCR with the Auto Set Up function 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Abbreviation Country
Language
Czech
CZ
Czech
HUN
PL
Hungary
Poland
Russia
Hungarian
Polish
RUS
ELSE
Russian
Other countries English
If your country does not appear in the list, select ELSE.
Press AUTO SET UP.
AUTO SET UP
3
The VCR starts searching for all of the receivable channels and presets them
in the appropriate order for your local area.
RF CHANNEL
AUTEU
SMARTLINK
C
P
H
M
S
starts and the SMARTLINK indicator flashes in the display window during
download.
After the search or download is complete, the current time appears in the
display window for any stations that transmit a time signal.
To cancel the Auto Set Up function
Press AUTO SET UP.
Tip
•
If you want to change the language for the on-screen display from the one preset in the Auto
Set Up function, see page 25.
Notes
•
Do not cancel the Auto Set Up function during step 3. If you do, repeat Auto Set Up from the
beginning.
•
When you operate the Auto Set Up function, some of the settings (ShowView, timer etc...)
will be reset. In this case, you have to set them again.
20 Setting up the VCR with the Auto Set Up function
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 6 : Setting the clock
You must set the time and date on the VCR to
use the timer recording features properly.
If the VCR clock was not set in the Auto Set
Up procedure, you need to set it manually.
MENU
The Auto Clock Set function works only if a
station in your area is broadcasting a time
signal. If the Auto Set Up function did not set
the clock correctly for your local area, try
another station for the Auto Clock Set
function.
M/m/</,
OK
Setting the clock manually
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
Press MENU, then press M/m to
highlight SETTINGS and press OK.
MENU
SETTINGS
1
TUNER
CLOCK
LANGUAGE
TV GUIDE PAGE
RETURN
PLAY
OK
SELECT
SET
:
: OK
EXIT : MENU
Press M/m to highlight CLOCK, then
press OK.
CLOCK
2
AUTO ADJUST
OFF
PLAY
MANUAL ADJUST
1
. 1 . 2 0 0 0
SAT
0 : 0 0
OK
SELECT
SET
:
: OK
EXIT : MENU
Press M/m to highlight MANUAL
ADJUST, then press OK.
CLOCK
3
AUTO ADJUST
OFF
PLAY
MANUAL ADJUST
OK
1
. 1 . 2 0 0 0
SAT
0 : 0 0
SELECT
SET
:
:
CONFIRM : OK
EXIT : MENU
continued
Setting the clock 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Press M/m to set the date.
CLOCK
4
5
6
7
8
PLAY
OK
AUTO ADJUST
OFF
MANUAL ADJUST
28 . 1 . 2 0 0 0
FRI
0 : 0 0
SELECT
SET
:
:
CONFIRM : OK
EXIT : MENU
Press , to highlight the month and set
the month pressing M/m.
CLOCK
AUTO ADJUST
OFF
OFF
OFF
PLAY
OK
MANUAL ADJUST
2 8 . 9 . 2 0 0 0
THU
0 : 0 0
SELECT
SET
:
:
CONFIRM : OK
EXIT : MENU
Set the year, hour, and minutes in
sequence, pressing , to highlight the
item to be set, and press M/m to select the
digits.
CLOCK
AUTO ADJUST
PLAY
OK
MANUAL ADJUST
2 8 . 9 . 2 0 0 0
THU
1 8 : 0 0
The day of the week is set automatically.
SELECT
SET
:
:
CONFIRM : OK
EXIT : MENU
Press OK to confirm the setting and start
the clock.
CLOCK
AUTO ADJUST
PLAY
OK
MANUAL ADJUST
2 8 . 9 . 2 0 0 0
THU
1 8 : 0 0
SELECT
SET
:
: OK
EXIT : MENU
Press MENU to exit the menu.
MENU
Tip
•
To change the digits while setting, press < to return to the item to be changed, and select
the digits pressing M/m.
Note
The menu disappears automatically if you don’t proceed for more than a few minutes.
•
22 Setting the clock
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the station for the Auto Clock Set function
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
MENU
M/m/</,
OK
Press MENU, then press M/m to
highlight SETTINGS and press OK.
SETTINGS
MENU
1
TUNER
CLOCK
LANGUAGE
TV GUIDE PAGE
RETURN
PLAY
SELECT
SET
:
: OK
OK
EXIT : MENU
Press M/m to highlight CLOCK, then
press OK.
CLOCK
2
3
PLAY
OK
AUTO ADJUST
OFF
MANUAL ADJUST
AUTO ADJUST is highlighted.
1
. 1 . 2 0 0 0
SAT
0 : 0 0
SELECT
SET
:
: OK
EXIT : MENU
Press OK.
CLOCK
AUTO ADJUST
ON
OFF
PLAY
OK
CLOCK PROGRAM
MANUAL ADJUST
2 8 . 9 . 2 0 0 0
THU
1 8 : 0 0
SELECT
:
CONFIRM : OK
EXIT : MENU
continued
Setting the clock 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Press M/m to highlight ON, then press
OK.
CLOCK
4
AUTO ADJUST
ON
1
PLAY
OK
CLOCK PROGRAM
MANUAL ADJUST
2 8 . 9 . 2 0 0 0
AAB
THU
1 8 : 0 0
SELECT
SET
:
: OK
EXIT : MENU
Press m to highlight CLOCK
PROGRAM, then press OK.
CLOCK
5
6
7
PLAY
OK
AUTO ADJUST
CLOCK PROGRAM
MANUAL ADJUST
2 8 . 9 . 2 0 0 0
1
AAB
1 8 : 0 0
THU
SELECT
:
CONFIRM : OK
EXIT : MENU
Press M/m until the programme position
of the station that carries the time signal
appears.
CLOCK
PLAY
OK
AUTO ADJUST
CLOCK PROGRAM
MANUAL ADJUST
2 8 . 9 . 2 0 0 0
2
CDE
1 8 : 0 0
THU
If the VCR does not receive the time
signal from any station, AUTO ADJUST
returns to OFF automatically.
SELECT
:
CONFIRM : OK
EXIT : MENU
Press MENU to exit the menu.
MENU
Tips
•
To change the digits while setting, press < to return to the item to be changed, and select
the digits using M/m.
•
If you set AUTO ADJUST to ON, the Auto Clock Set function is activated whenever the
VCR is turned off. The time is adjusted automatically by making reference to the time signal
from the station whose programme position is displayed in the “CLOCK PROGRAM” row.
If you do not need the Auto Clock Set function, select OFF.
Note
The menu disappears automatically if you don’t proceed for more than a few minutes.
•
24 Setting the clock
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a language
You can change the on-screen display
language from the one you selected with the
Auto Set Up function.
MENU
Before you start…
• Turn on the VCR and the TV.
M/m/</,
OK
• Set the TV to the video channel.
Press MENU, then press M/m to
highlight SETTINGS and press OK.
SETTINGS
MENU
1
TUNER
CLOCK
LANGUAGE
TV GUIDE PAGE
RETURN
PLAY
OK
SELECT
SET
:
: OK
EXIT : MENU
Press M/m to highlight LANGUAGE,
then press OK.
LANGUAGE
2
PLAY
ENGLISH
POLSKI
ČESKÝ
OK
MAGYAR
SLOVENČINA
TÜRKÇE
РУССКИЙ
SELECT
SET
:
: OK
EXIT : MENU
Press M/m/</, to highlight the desired language, then press OK.
3
PLAY
OK
Note
•
The menu disappears automatically if you don’t proceed for more than a few minutes.
Selecting a language 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Presetting channels
If some channels could not be preset using
the Auto Set Up function, you can preset
them manually.
PROG +/–
Before you start…
MENU
• Turn on the VCR and the TV.
• Set the TV to the video channel.
M/m/</,
OK
Press MENU, then press M/m to
highlight SETTINGS and press OK.
SETTINGS
MENU
1
TUNER
CLOCK
LANGUAGE
TV GUIDE PAGE
RETURN
PLAY
OK
SELECT
SET
:
: OK
EXIT : MENU
Press M/m to highlight TUNER, then
press OK.
TUNER
PROG.
1
2
3
SYSTEM
D/K
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
NORMAL
1 2 AAB
PLAY
OK
C
OFF
ON
FINE TUNING
RETURN
SELECT
SET
:
: OK
EXIT : MENU
Press M/m to highlight NORMAL/CATV,
then press OK.
TUNER
SYSTEM
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
PROG.
1
D/K
NORMAL
1 2 AAB
PLAY
OK
C
OFF
ON
Press M/m to highlight NORMAL, then
press OK.
FINE TUNING
RETURN
To preset CATV (Cable Television)
channels, select CATV.
SELECT
SET
:
: OK
EXIT : MENU
26 Presetting channels
Download from Www.Somanuals.com. All Manuals Search And Download.
Press M/m to highlight CHANNEL SET.
TUNER
SYSTEM
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
4
5
PROG.
1
D/K
PLAY
OK
NORMAL
1 2 AAB
C
OFF
ON
FINE TUNING
RETURN
SELECT
SET
:
: OK
EXIT : MENU
Press PROG +/– to select the programme
position.
Selected programme
position
PROG
TUNER
PROG.
4
SYSTEM
D/K
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
NORMAL
C
1 2 AAB
OFF
ON
FINE TUNING
RETURN
SELECT
SET
:
: OK
EXIT : MENU
Press OK to highlight the channel
number row, then press M/m to start
tuning.
TUNER
PROG.
TUV
4
6
D/K
SYSTEM
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
PLAY
OK
C
2 7
ON
FINE TUNING
RETURN
The VCR starts searching for a channel
and displays the first one it finds on the
TV screen. Press M/m repeatedly until
the channel you want is displayed.
SELECT
:
CONFIRM : OK
EXIT : MENU
The channels are scanned in the
following order:
B/G TV system
D/K TV system
Channel number in Channel
the CHANNEL SET
field
Channel number in Channel
the CHANNEL SET
field
C02
C03
C04
C05
C06
C07
C08
C09
E2
E3
E4
E5
E6
E7
E8
E9
C02
C05
C06
C12
C13
C14
C15
C16
R1
R6
R7
R12
R2
R3
R4
R5
continued
Presetting channels 27
Download from Www.Somanuals.com. All Manuals Search And Download.
B/G TV system
D/K TV system
Channel number in Channel
the CHANNEL SET
field
Channel number in Channel
the CHANNEL SET
field
C10
E10
C17
R8
C11
E11
C18
R9
C12
E12
C19
R10
C21-C69
CATV S01-S41
CATV S42-S46
E21-E69
S01-S41
S01-S05
C20
R11
C21-C69
R21-R69
If you know the number of the channel you want, press the programme number
buttons. For example, for channel 05, first press “0” and then press “5.”
If the sound is distorted or noisy, press
TUNER
7
8
PROG.
1
OK then to highlight SYSTEM, then
select B/G or D/K so that you can get the
better sound. .
SYSTEM
D/K
PLAY
OK
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
NORMAL
1 2 AAB
C
OFF
ON
FINE TUNING
RETURN
SELECT
SET
:
: OK
EXIT : MENU
Press OK.
PLAY
OK
To allocate another channel to another programme position, repeat steps 4
to 8.
9
Press MENU to exit the menu.
MENU
10
28 Presetting channels
Download from Www.Somanuals.com. All Manuals Search And Download.
Disabling unwanted programme positions
After tuning the TV channels, you can disable unused programme positions. The
disabled positions will be skipped later when you press the PROG +/– buttons.
You can also disable unwanted programme positions using the CHANNEL LIST
menu (see page 32).
In step 6 above, press programme number button “0” twice to display the number
1 “00” beside CHANNEL SET.
Press OK to confirm the setting, then MENU to exit the menu.
2
If the picture is not clear
Normally, the Auto Fine Tuning (AFT) function automatically tunes in channels
clearly. If the picture is not clear, you may also use the manual tuning function.
Press PROG +/– or the programme number buttons to select the programme
1 position for which you cannot obtain a clear picture.
Press MENU, then select SETTINGS and press OK.
2
Select TUNER, then press OK.
3
Select FINE TUNING.
4
The fine tuning meter appears.
TUNER
PROG.
NORMAL
4
Selected programme
position
D/K
SYSTEM
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
C
2 7 TUV
OFF
FINE TUNING
RETURN
SET
:
EXIT : MENU
Press </, to get a clearer picture, then press MENU to exit the menu.
5
Note that the AFT (Auto Fine Tuning) setting switches to OFF.
Note
The menu disappears automatically if you don’t proceed for more than a few minutes.
•
Presetting channels 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting/changing the station names
You can also set and change station names as
you like up to 5 characters. The set station
names are displayed on the TV screen when
you change the programme position on the
VCR.
MENU
Before you start…
• Turn on the VCR and the TV.
M/m/</,
OK
• Set the TV to the video channel.
Press MENU, then press M/m to
highlight LISTS and press OK.
MENU
LISTS
1
CHANNEL LIST
TIMER LIST
RETURN
PLAY
SELECT
SET
:
: OK
OK
EXIT : MENU
Press M/m to highlight CHANNEL LIST,
then press OK.
CHANNEL LIST
2
3
PROG
CH
NAME
AAB
CDE
1
2
3
4
5
C
C
C
C
C
1 2
0 3
5 6
2 7
0 9
PLAY
OK
FGH
SELECT
MOVE PROGRAM
ERASE PROGRAM
:
:
:
CLEAR
EXIT : MENU
Press M/m to highlight the row on which
you want to set or change the station
name.
CHANNEL LIST
PROG
CH
NAME
AAB
CDE
PLAY
OK
1
2
3
4
5
C
C
C
C
C
1 2
0 3
5 6
2 7
0 9
To display other pages for programme
FGH
positions 6 to 60, press M/m repeatedly.
SELECT
MOVE PROGRAM
ERASE PROGRAM
:
:
:
CLEAR
EXIT : MENU
30 Setting/changing the station names
Download from Www.Somanuals.com. All Manuals Search And Download.
• If you want to set the station name,
press , twice to highlight the station
name column only.
• If you don’t want to set the station
name, go to step 7.
CHANNEL LIST
4
5
PROG
CH
NAME
AAB
PLAY
OK
1
2
3
4
5
C
C
C
C
C
1 2
0 3
5 6
2 7
0 9
CDE
FGH
SELECT A CHARACTER
NEXT
CONFIRM
:
:
: OK
EXIT : MENU
Enter the station name.
CHANNEL LIST
PROG
CH
NAME
1 Press M/m to select a character.
Each time you press M, the character
changes as shown below.
PLAY
OK
1
2
3
4
5
C
C
C
C
C
1 2
0 3
5 6
2 7
0 9
AAB
CDE
L
FGH
At Bt ... t Z t a t b t...
t z t 0 t 1 t ... t 9 t
(symbols) t(blank space) t A
SELECT A CHARACTER
NEXT
PREVIOUS
:
:
:
EXIT : MENU
2 Press CURSOR, to set the next character.
The next space is highlighted.
To correct a character, press CURSOR < until the character you want
to correct is highlighted, then reset it.
You can set up to 5 characters for the station name.
To change or to set the station name of another station, repeat steps 2 to 4.
6
7
Press OK to confirm the setting.
CHANNEL LIST
PROG
CH
1 2
0 3
5 6
2 7
0 9
NAME
AAB
CDE
LMO
PLAY
OK
1
2
3
4
5
C
C
C
C
C
FGH
SELECT
MOVE PROGRAM
ERASE PROGRAM
:
:
:
CLEAR
EXIT : MENU
Press MENU to exit the menu.
MENU
8
Note
•
The menu disappears automatically if you don’t proceed for more than a few minutes.
Setting/changing the station names 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/disabling programme positions
After setting the channels, you can change
the programme positions as you like. If any
programme positions are unused or contain
unwanted channels, you can disable them.
MENU
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
M/m/</,
OK
Changing programme positions
Press MENU, then press M/m to
highlight LISTS and press OK.
MENU
LISTS
1
CHANNEL LIST
TIMER LIST
RETURN
PLAY
SELECT
SET
:
OK
: OK
EXIT : MENU
Press M/m to highlight CHANNEL LIST,
then press OK.
CHANNEL LIST
2
PLAY
OK
PROG
CH
NAME
AAB
CDE
1
2
3
4
5
C
C
C
C
C
1 2
0 3
5 6
2 7
0 9
FGH
SELECT
MOVE PROGRAM
ERASE PROGRAM
:
:
:
CLEAR
EXIT : MENU
32 Changing/disabling programme positions
Download from Www.Somanuals.com. All Manuals Search And Download.
Press M/m to highlight the row on which
you want to change the programme
position, then press
CHANNEL LIST
3
4
5
PROG
CH
NAME
AAB
CDE
LMO
PLAY
OK
1
2
3
4
5
C
C
C
C
C
1 2
0 3
5 6
2 7
0 9
,.
FGH
To display other pages for programme
positions 6 to 60, press M/m repeatedly.
SELECT
SET STATION NAME
CONFIRM
:
:
: OK
EXIT : MENU
Press M/m until the selected channel row
moves to the desired programme
position.
CHANNEL LIST
PROG
CH
NAME
LMO
AAB
PLAY
OK
1
2
3
4
5
C
C
C
C
C
5 6
1 2
0 3
2 7
0 9
CDE
FGH
The selected channel is inserted at the
new programme position and the
intermediate channels are displaced to fill
the gap.
SELECT
:
:
SET STATION NAME
CONFIRM
: OK
EXIT : MENU
Press OK to confirm the setting.
PLAY
OK
To change the programme position of another station, repeat steps 3 to 5.
Press MENU to exit the menu.
6
7
MENU
continued
Changing/disabling programme positions 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Disabling unwanted
programme positions
After presetting channels, you can disable
unused programme positions.The disabled
positions will be skipped later when you
press the PROG +/– buttons.
CLEAR
1
4
7
2
5
8
0
3
6
9
MENU
M/m/</,
OK
Press MENU, then press M/m to
highlight LISTS, and press OK.
MENU
LISTS
1
2
CHANNEL LIST
TIMER LIST
RETURN
PLAY
OK
SELECT
SET
:
: OK
EXIT : MENU
Press M/m to highlight CHANNEL LIST,
then press OK.
CHANNEL LIST
PLAY
OK
PROG
CH
NAME
AAB
CDE
1
2
3
4
5
C
C
C
C
C
1 2
0 3
5 6
2 7
0 9
FGH
SELECT
MOVE PROGRAM
ERASE PROGRAM
:
:
:
CLEAR
EXIT : MENU
34 Changing/disabling programme positions
Download from Www.Somanuals.com. All Manuals Search And Download.
Press M/m to highlight the row which
you want to disable.
CHANNEL LIST
3
4
PROG
CH
NAME
AAB
CDE
LMO
PLAY
OK
1
2
3
4
5
C
C
C
C
C
1 2
0 3
5 6
2 7
0 9
FGH
SELECT
MOVE PROGRAM
ERASE PROGRAM
:
:
:
CLEAR
EXIT : MENU
Press CLEAR.
CLEAR
CHANNEL LIST
The selected row will be cleared as
shown on the right.
PROG
CH
1 2
0 3
NAME
AAB
CDE
1
2
3
4
5
C
C
C
C
2 7
0 9
FGH
SELECT
MOVE PROGRAM
ERASE PROGRAM
:
:
:
CLEAR
EXIT : MENU
Repeat steps 3 and 4 for any other programme positions you want to
disable.
5
6
MENU
Press MENU to exit the menu.
Notes
•
•
The menu disappears automatically if you don’t proceed for more than a few minutes.
Be sure to select the programme position you want to disable correctly. If you disable a
programme position by mistake, you need to reset that channel manually.
Changing/disabling programme positions 35
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the PAY-TV/Canal Plus decoder
You can watch or record PAY-TV/Canal Plus programmes if you connect a decoder
(not supplied) to the VCR.
Connecting a decoder
Scart cable
Scart
(supplied with decoder)
(EURO-AV)
PAY-TV/Canal Plus
decoder
DECODER/t LINE-3 IN
AERIAL IN
AERIAL OUT
i LINE-1
(TV)
Aerial cable
(supplied)
AERIAL IN
Scart
(EURO-AV
Scart cable (not supplied)
:Signal flow
36 Setting the PAY-TV/Canal Plus decoder
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting PAY-TV/Canal Plus
channels
PROG +/–
To watch or record PAY-TV/Canal Plus
programmes, set your VCR to receive the
channels using the on-screen display.
MENU
Before you start…
• Turn on the VCR, the TV, and the decoder.
M/m/</,
OK
• Set the TV to the video channel.
Press MENU, then press M/m to
highlight OPTIONS and press OK.
OPTIONS
MENU
1
2
3
VIDEO OPTIONS
AUDIO OPTIONS
TAPE OPTIONS
OTHER OPTIONS
RETURN
PLAY
OK
SELECT
SET
:
: OK
EXIT : MENU
Press M/m to highlight OTHER
OPTIONS, then press OK.
OTHER OPTIONS
PLAY
OK
BUZZER
DIMMER
DECODER/LINE3
POWER SAVE
TIMER OPTIONS
TV DIRECT REC
RETURN
ON
OFF
DECODER
OFF
VARIABLE
ON
SELECT
SET
:
: OK
EXIT : MENU
Press M/m to highlight DECODER/
LINE3, then press OK.
OTHER OPTIONS
BUZZER
DIMMER
DECODER/LINE3
POWER SAVE
TIMER OPTIONS
TV DIRECT REC
RETURN
ON
PLAY
OK
DECODER
LINE3
ON
SELECT
:
CONFIRM : OK
EXIT : MENU
continued
Setting the PAY-TV/Canal Plus decoder 37
Download from Www.Somanuals.com. All Manuals Search And Download.
Press M/m to highlight DEC., then press
OK.
OTHER OPTIONS
4
PLAY
OK
BUZZER
DIMMER
DECODER/LINE3
POWER SAVE
TIMER OPTIONS
TV DIRECT REC
RETURN
ON
OFF
DECODER
OFF
VARIABLE
ON
SELECT
SET
:
: OK
EXIT : MENU
Press MENU to exit the menu.
MENU
MENU
5
6
Press MENU, then press M/m to
highlight SETTINGS and press OK.
SETTINGS
TUNER
CLOCK
LANGUAGE
TV GUIDE PAGE
RETURN
PLAY
OK
SELECT
SET
:
: OK
EXIT : MENU
Press M/m to highlight TUNER, then
press OK.
TUNER
SYSTEM
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
7
8
PROG.
1
D/K
NORMAL
1 2 AAB
PLAY
OK
C
OFF
ON
FINE TUNING
RETURN
SELECT
SET
:
: OK
EXIT : MENU
Press M/m to highlight NORMAL/
CATV, then press OK.
TUNER
PROG.
NORMAL
1
SYSTEM
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
PLAY
OK
C
ATV
ON
FINE TUNING
RETURN
SELECT
:
CONFIRM : OK
EXIT : MENU
38 Setting the PAY-TV/Canal Plus decoder
Download from Www.Somanuals.com. All Manuals Search And Download.
Press M/m to highlight NORMAL, then
press OK.
TUNER
SYSTEM
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
PROG.
1
9
D/K
NORMAL
1 2 AAB
PLAY
OK
C
OFF
ON
To preset CATV (Cable Television)
channels, select CATV.
FINE TUNING
RETURN
SELECT
SET
:
: OK
EXIT : MENU
Press PROG +/– to select the desired
programme position.
PROG
10
Selected programme
position
TUNER
PROG.
4
SYSTEM
D/K
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
NORMAL
C
1 2 AAB
OFF
ON
FINE TUNING
RETURN
SELECT
SET
:
: OK
EXIT : MENU
Press M/m to highlight CHANNEL SET,
then press OK.
TUNER
SYSTEM
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
11
12
13
PROG.
AAB
4
D/K
PLAY
OK
C
1 2
ON
FINE TUNING
RETURN
SELECT
:
CONFIRM : OK
EXIT : MENU
Press M/m to select the PAY-TV/Canal
Plus channel.
TUNER
PROG.
4
D/K
SYSTEM
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
NORMAL
PLAY
OK
C
0 2
PQR
OFF
ON
When the desired channel is tuned, press
OK.
FINE TUNING
RETURN
SELECT
SET
:
: OK
EXIT : MENU
Press M/m to highlight PAY-TV/
CANAL+, then press OK.
TUNER
SYSTEM
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
PROG.
4
D/K
NORMAL
PLAY
OK
ON
OFF
FINE TUNING
RETURN
SELECT
:
CONFIRM : OK
EXIT : MENU
continued
Setting the PAY-TV/Canal Plus decoder 39
Download from Www.Somanuals.com. All Manuals Search And Download.
Press M/m to highlight ON, then press
OK.
TUNER
SYSTEM
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
PROG.
4
14
15
16
D/K
NORMAL
PLAY
OK
C
ON
ON
0 2 PQR
FINE TUNING
RETURN
SELECT
SET
:
: OK
EXIT : MENU
If the sound is distorted or noisy, press
M/m/ </, to highlight SYSTEM, then
select B/G or D/K so that you get the
better sound.
TUNER
PROG.
4
D/K
SYSTEM
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
NORMAL
0 2 PQR
PLAY
OK
C
ON
ON
FINE TUNING
RETURN
SELECT
SET
:
: OK
EXIT : MENU
Press MENU to exit the menu.
MENU
Notes
•
•
The menu disappears automatically if you don’t proceed for more than a few minutes.
To superimpose subtitles while watching PAY-TV/Canal Plus programmes, make both
decoder-VCR and VCR-TV connections using 21-pin Scart cables that are compatible with
the RGB signals.You cannot record subtitles on the VCR.
•
Some PAY-TV/Canal Plus decoders may not work if you set the PAY-TV/CANAL + setting to
ON. In this case, set it to OFF.
40 Setting the PAY-TV/Canal Plus decoder
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
Playing a tape
Z EJECT
DISPLAY
CLEAR
1
4
7
2
5
8
0
3
6
9
H PLAY
X PAUSE
M
FF
x STOP
REW
m
NTSC PB
Turn on your TV and set it to the video channel.
Insert a tape.
1
2
The VCR turns on and starts playing
automatically if you insert a tape with its
safety tab removed.
continued
Playing a tape 41
Download from Www.Somanuals.com. All Manuals Search And Download.
Press H PLAY.
3
PLAY
OK
When the tape reaches the end, it will rewind automatically.
Additional tasks
To
Press
Stop play
x STOP
Pause play
X PAUSE
Resume play after pause
Fast-forward the tape
Rewind the tape
Eject the tape
X PAUSE or H PLAY
M FF during stop
m REW during stop
Z EJECT
To set the colour system
If the playback picture has no colour or streaks appeat during playback, set the
COLOUR SYSTEM option in the VIDEO OPTIONS menu to contorm to the system
that the tape was recorded (see page 68). (Normally set the option to AUTO)
To play an NTSC-recorded tape
Set NTSC PB at the rear of the VCR according to the colour system of your TV.
When your TV is
PAL only
Set NTSC PB to
ON PAL TV
PAL and NTSC
NTSC 4.43
To use the time counter
Press CLEAR at the point on the tape that you want to find later. The counter in the
display window resets to “0:00:00.” Search for the point afterwards by referring to
the counter.
PDC
H
M
S
To display the counter on the TV screen, press
DISPLAY.
42 Playing a tape
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
•
•
•
The counter resets to “0:00:00” whenever a tape is reinserted.
The counter stops counting when it comes to a portion with no recording.
Depending on your TV, the following may occur while playing an NTSC-recorded tape:
– The picture becomes black and white.
– The picture shakes.
– No picture appears on the TV screen.
– Black streaks appear horizontally on the TV screen.
– The colour density increases or decreases.
•
•
If you playback a tape in LP or EP mode with the NTSC system, the sound is heard in
monaural.
While setting the menu on the TV screen, you cannot use M/m/</, buttons for tape
operation.
Starting playback automatically with one button (One
Touch Play)
If you use the SMARTLINK connection, you can turn on the VCR and the TV, set the
TV to the video channel, and start playback automatically with one button.
Insert a tape.
1
The VCR automatically turns on.
If you insert a tape with its safety tab removed, the TV turns on and switches to
the video channel. Playback starts automatically.
Press H PLAY.
2
The TV turns on and switches to the video channel automatically. Playback
starts.
Tip
•
When there already is a tape in the VCR, the VCR and the TV turn on, the TV is set to the
video channel, and playback starts automatically in one sequence when you press H PLAY.
Note
When you use the One Touch Play function, leave the TV on or in the standby mode.
•
Playing a tape 43
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording TV programmes
COUNTER/REMAIN
DISPLAY
SP/LP
t TV/VIDEO
1
4
7
2
5
8
0
3
6
9
INPUT SELECT
PROG +/–
z REC
x STOP
Turn on your TV and set it to the video channel.
To record from a decoder or other source, turn it on.
1
2
Insert a tape with its safety tab in place.
44 Recording TV programmes
Download from Www.Somanuals.com. All Manuals Search And Download.
• To record a terrestrial channel.
Press PROG +/– until the programme position number you want appears
in the display window.
PROG
3
SP
OPC
VIDEO
PDC
H
M
S
• To record a video source from the LINE-1 (TV) or LINE-3 (Scart)
connector, or the LINE-2IN jacks. Press INPUT SELECT until L1, L2 or
L3 appears in the display window.
INPUT
SELECT
SP
OPC
VIDEO
H
M
S
Press SP/LP to select the tape speed, SP or LP.
SP/LP
4
5
LP (Long Play) provides recording time twice as long as SP. However, SP
(Standard Play) produces better picture and audio quality.
SP
LP
OC
VIDEO
PDC
H
M
S
Press z REC to start recording.
The recording indicator lights up red in the display window.
REC
Recording
indicator
LP
VIDEO
PDC
H
M
S
To stop recording
Press x STOP.
continued
Recording TV programmes 45
Download from Www.Somanuals.com. All Manuals Search And Download.
To check the remaining time
Press
DISPLAY. With the display on, press COUNTER/REMAIN to check the
remaining time. Each time you press COUNTER/REMAIN, the time counter and the
remaining time appear alternately. The
indicator indicates the remaining time.
SP
0 : 0 0 : 2 2
1H46M
Time counter
Remaining time
In order to get an accurate remaining time indication, be sure the TAPE LENGTH
item in the TAPE OPTIONS menu is set according to the tape type you use (see page
68).
To watch another TV programme while recording
Press t TV/VIDEO on the remote commander to turn off the VIDEO indicator
1 in the display window.
Select another programme position on the TV.
2
To protect a recording
To prevent accidental erasure, break off the safety
tab as illustrated. To record on a tape again, cover
the tab hole with adhesive tape.
You can also protect a recording by using the
SmartFile function (see page 94).
Tips
Safety tab
•
To select a programme position, you can use the
programme number buttons on the remote
commander. For two-digit numbers, press the –/– –(ten’s digit) button followed by the
programme number buttons.
•
•
The display appears on the TV screen indicating information about the tape, but the
information won’t be recorded on the tape.
If you don’t want to watch TV while recording, you can turn off the TV.
When using a decoder or other source, make sure to leave it on.
46 Recording TV programmes
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
•
If a tape has portions recorded in both PAL and NTSC systems, the time counter reading will
not be correct. This discrepancy is due to the difference between the counting cycles of the
two video systems.
•
You cannot watch a PAY-TV/Canal Plus programme while recording another PAY-TV/Canal
Plus programme.
•
•
The remaining time is intended for rough measurement only.
The remaining time will be displayed for only about 30 seconds after tape starts playback.
Recording what you are watching on the TV (TV Direct
Rec)
If you use the SMARTLINK connection, you can easily record what you are
watching on the TV (other than tapes being played on the VCR).
Insert a tape with its safety tab in place.
1
Press z REC while you are watching a TV programme or external source.
2
starts recording what you are watching on the TV.
Tips
•
The TV indicator appears in the display window after you press z REC in some situations
such as:
– when you are watching a source connected to the TV’s line input, or
– when the TV tuner preset data for the programme position is different from the data preset
in the VCR tuner.
•
•
If there already is a tape with its safety tab in place in the VCR, the VCR automatically turns
on and starts recording what you are watching on the TV when you press z REC.
You can turn the TV Direct Rec function ON and OFF in the OTHER OPTIONS menu (see
page 68).
Notes
•
You cannot record what you are watching using this method when the VCR is in the
following modes : pause, timer standby, tuner preset, Auto Set Up, and recording.
•
When the TV indicator is lit in the display window, do not turn off the TV nor change the TV
programme position. When the TV indicator is not lit, the VCR continues recording the
programme even if you change the TV programme position on the TV.
Recording TV programmes 47
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording TV programmes using the
ShowView system
The ShowView system is a feature that
simplifies programming the VCR to make
timer recordings. Just enter the ShowView
number listed in the TV programme guide.
The date, times, and programme position of
that programme are set automatically. You
can preset up to eight programmes at a time.
?/1
Before you start…
SP/LP
• Check that the VCR clock is set to the
CLEAR
correct time and date.
• Insert a tape with its safety tab in place.
Make sure the tape is longer than the total
recording time.
• Turn on your TV and set it to the video
channel.
• If you insert a tape with the SmartFile
function, make sure the total recording
time doesn’t overlap the protected
programme. For details about the
SmartFile function, see page 74.
1
4
7
2
5
8
0
3
6
9
Programme
number
buttons
• Set TIMER OPTIONS to SHOWVIEW or
VARIABLE in the OTHER OPTIONS
menu (see page 70).
TIMER
M/m/</,
OK
x STOP
48 Recording TV programmes using the ShowView system
Download from Www.Somanuals.com. All Manuals Search And Download.
Press
TIMER.
TIMER
1
• When you set TIMER OPTIONS to
VARIABLE:
TIMER METHOD
STANDARD
SHOWVIEW
The TIMER METHOD menu appears
on the TV screen. Press M/m to select
SHOWVIEW, then press OK.
PLAY
OK
SELECT
SET
:
: OK
EXIT : MENU
• When you set TIMER OPTIONS to
SHOWVIEW:
The SHOWVIEW menu appears on
the TV screen.
SHOWVIEW
2 8 . 9 THU
SHOWVIEW NO.
– – – – – – – – –
SET
:
0–9
EXIT : MENU
Press the programme number buttons to
enter the ShowView number.
SHOWVIEW
2
1
4
7
2
5
8
0
3
6
9
2 8 . 9 THU
SHOWVIEW NO.
1 2 4 6 – – – – –
If you make a mistake, press CLEAR and
re-enter the correct number.
SET
:
0–9
CLEAR
CONFIRM : OK
CANCEL
:
CLEAR
EXIT : MENU
continued
Recording TV programmes using the ShowView system 49
Download from Www.Somanuals.com. All Manuals Search And Download.
Press OK.
TIMER
3
2 8 . 9 THU
DATE
TIME
PROG.
AAB
PLAY
OK
The date, start and stop times,
programme position, tape speed, and
VPS/PDC setting appear on the TV
screen.
TODAY
SP / LP
LIST
2 0 : 0 0 2 1 : 0 0
SP
VPS / PDC
OFF
SELECT
:
:
:
SET
If “– –” appears in the “PROG.”
(programme) column (this may happen
for local broadcasts), you have to set the
appropriate programme position
manually.
CANCEL
CLEAR
EXIT : MENU
• To select a terrestrial channel.
Press M/m to select the desired programme position.
• To select a video source from the LINE-1 (TV) or LINE-3 IN
connector, or the LINE-2 IN jacks.
Press INPUT SELECT to select the desired video source.
You will only have to do this operation once for the referred channel. The
VCR will then store your setting.
For details about the VPS/PDC function, see “Timer recording with VPS/
PDC signals” on page 51.
CLEAR
If the information is incorrect, press CLEAR to cancel the setting.
If you want to change the date, tape
speed, and the VPS/PDC function
setting:
4
2 8 . 9 THU
DATE
TODAY
TIME
PROG.
AAB
PLAY
OK
2 0 : 0 0 2 1 : 0 0
SP / LP
LIST
SP
VPS / PDC
OFF
1 Press </, to highlight the item you
want to change.
SELECT
:
:
:
SET
CANCEL
CLEAR
2 Press M/m to reset it.
EXIT : MENU
• To record the same programme every
day or the same day every week, see “Daily/weekly recording” on page
51.
• To use the VPS/PDC function, set VPS/PDC to ON. For details about
the VPS/PDC function, see “Timer recording with VPS/PDC signals”
on page 51.
• To change the setting, press MENU, and highlight LIST, then select
TIMER LIST and press OK. Then enter the new timer setting and press
OK.
CLEAR
If the informations are not correct, press CLEAR to cancel the settings.
50 Recording TV programmes using the ShowView system
Download from Www.Somanuals.com. All Manuals Search And Download.
Press OK to confirm the setting.
5
6
PLAY
OK
Press ?/1 to turn off the VCR.
The indicator appears in the display window and the VCR stands by for
recording.
To stop recording
To stop the VCR while recording, press x STOP.
Daily/weekly recording
In step 4 above, press m to select the recording pattern. Each time you press m, the
indication changes as shown below. Press M to change the indication in reverse
order.
TODAY t SUN-SAT (Sunday to Saturday) t MON-SAT (Monday to
Saturday) t MON-FRI (Monday to Friday) t SAT (every Saturday) .....
t MON (every Monday) t SUN (every Sunday) t 1 month later
t (dates count down) t TOMORROW t TODAY
Timer recording with VPS/PDC signals
Some broadcast systems transmit VPS (Video Programme System) or PDC
(Programme Delivery Control) signals with their TV programmes. These signals
ensure that your timer recordings are made regardless of broadcast delays, early
starts, or broadcast interruptions (when the VPS or PDC indicator in the display
window is lit).
In step 4 above, press M/m to turn on/off the VPS/PDC indication after you set the
recording date. If you do not want to set the VPS/PDC function, turn off the VPS/
PDC indication.
You can also use the VPS/PDC function for a source connected to the LINE-1 (TV)
and LINE-3 IN (Scart) connectors, or the LINE-2 IN jacks.
continued
Recording TV programmes using the ShowView system 51
Download from Www.Somanuals.com. All Manuals Search And Download.
To use the VCR after setting the timer
To use the VCR before a timer recording begins, just press ?/1. The
indicator
turns off and the VCR switches on. Remember to press ?/1 to reset the VCR after
using the VCR.
You can also do the following tasks while the VCR is recording:
• Reset the counter.
• Display tape information on the TV screen.
• Watch another TV programme.
Tips
•
To set the programme position with a two digit number, press –/– – (ten’s digit) button
followed by the programme number button.
•
To set the programme position, you can also use the PROG +/– or programme number
buttons.
•
•
To set the tape speed, you can also use the SP/LP button.
When you are recording a programme in the SP mode and the remaining tape becomes
shorter than the recording time, the tape speed is automatically changed to the LP mode.
Note that some interference will appear on the picture at the point the tape speed is changed.
If you want to keep the same tape speed, set AUTO LONG PLAY to OFF in the TAPE
OPTIONS menu (see page 68).
•
To check, change, or cancel the programme setting, press </, to choose LIST, then press
OK after step 4. For details, see step 3 in “Checking/changing/cancelling timer settings on
page 61.
Notes
•
When setting the timer with VPS/PDC signals, enter the start and stop times exactly as
indicated in the TV programme guide, otherwise the VPS/PDC function won’t work and the
recording won’t start.
•
If the VPS/PDC signal is too weak or the broadcasting station failed to transmit VPS/PDC
signals, the VCR will start recording at the set time without using the VPS/PDC function.
•
•
The
indicator flashes in the display window when you press ?/1 with no tape inserted.
The VPS/PDC function is automatically set to OFF for the timer recording of a satellite
programme.
•
When you set TIMER OPTIONS to STANDARD in the OTHER OPTIONS menu, the
SHOWVIEW menu does not appear on the TV screen. Select SHOWVIEW or VARIABLE.
52 Recording TV programmes using the ShowView system
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the timer manually
If the ShowView system is not available in
your area, follow the instructions below to set
the timer to record programmes.
Before you start…
• Check that the VCR clock is set to the
correct time and date.
?/1
• Insert a tape with its safety tab in place.
Make sure the tape is longer than the total
recording time.
turn it on.
• Turn on your TV and set it to the video
channel.
• If you insert a tape with the SmartFile
function, make sure the total recording
time doesn’t overlap the protected
programme. For details about the
SmartFile function, see page 74.
• Set TIMER OPTIONS to STANDARD or
VARIABLE in the OTHER OPTIONS
menu (see page 70).
1
4
7
2
5
8
0
3
6
9
INPUT
SELECT
TIMER
M/m/</,
OK
x STOP
continued
Setting the timer manually 53
Download from Www.Somanuals.com. All Manuals Search And Download.
Press
TIMER.
TIMER
1
• When you set TIMER OPTIONS to
VARIABLE:
TIMER METHOD
STANDARD
SHOWVIEW
The TIMER METHOD menu appears
on the TV screen. Press M/m to select
STANDARD, then press OK.
PLAY
OK
SELECT
SET
:
: OK
EXIT : MENU
2 8 . 9 THU
• When you set TIMER OPTIONS to
STANDARD:
The TIMER menu appears on the TV
screen.
TIMER
DATE
TIME
PROG.
TODAY
SP / LP
LIST
– – : – – – – : – –
– –
SP
VPS / PDC
OFF
SELECT
:
:
:
SET
CANCEL
CLEAR
EXIT : MENU
Set the date, start and stop times,
programme position, tape speed, and
VPS/PDC function:
TIMER
. 1 0
2
2 8 . 9 THU
DATE
TIME
PROG.
PLAY
OK
2
SP / LP
LIST
LP
VPS / PDC
ON
1 Press , to highlight each item in
turn.
SELECT
:
:
:
SET
CANCEL
CLEAR
2 Press M/m to set each item.
EXIT : MENU
To correct a setting, press < to return to
that setting and reset it.
• To record the same programme every day or the same day every week,
see “Daily/weekly recording” on page 55.
• To use the VPS/PDC function, set VPS/PDC to ON. For details about
the VPS/PDC function, see “Timer recording with VPS/PDC signals”
on page 51.
• To record from a decoder or other source connected to the LINE-1 (TV)
or LINE-3 IN connectors, the LINE-2 IN jacks, press INPUT SELECT
to display “L1,” “L2,” “L3” in the “PROG.” position.
INPUT
SELECT
Press OK to confirm the setting.
3
PLAY
OK
54 Setting the timer manually
Download from Www.Somanuals.com. All Manuals Search And Download.
Press ?/1 to turn off the VCR.
4
The indicator appears in the display window and the VCR stands by for
recording.
To record from a decoder or other sources, leave the connected equipment
switched on.
To stop recording
To stop the VCR while recording, press x STOP.
Daily/weekly recording
In step 2 above, press m to select the recording pattern. Each time you press m, the
indication changes as shown below. Press M to change the indication in reverse
order.
Saturday) t MON-FRI (Monday to Friday) t SAT (every Saturday) .....
t MON (every Monday) t SUN (every Sunday) t 1 month later
t (dates count down) t TOMORROW t TODAY
Tips
•
To set the programme position, you can also use the PROG +/– or programme number
buttons.
•
•
To set the tape speed, you can also use the SP/LP button.
When you are recording a programme in the SP mode and the remaining tape becomes
shorter than the recording time, the tape speed is automatically changed to the LP mode.
Note that some interference will appear on the picture at the point the tape speed is changed.
If you want to keep the same tape speed, set AUTO LONG PLAY to OFF in the TAPE
OPTIONS menu (see page 68).
•
Even if you set TIMER OPTIONS to SHOWVIEW in the OTHER OPTIONS menu, you can
set the timer manually. Press MENU to select TIMER, then go to step 2.
Notes
•
When setting the timer with VPS/PDC signals, enter the start and stop times exactly as
indicated in the TV programme guide, otherwise the VPS/PDC function won’t work and the
recording won’t start.
•
•
If the VPS/PDC signal is too weak or the broadcasting station failed to transmit VPS/PDC
signals, the VCR will start recording at the set time without using the VPS/PDC function.
The
indicator flashes in the display window when you press ?/1 with no tape inserted.
Setting the timer manually 55
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Operations
Playing/searching at various speeds
X 2
y SLOW
1
4
7
2
5
8
0
3
6
9
H
m
M
M
FF
REW
m
Playback options
Operation
During stop, press M (fast-forward) or m ( rewind) and release.
During fast-forward, hold M FF down. During rewind, hold
REW down.
Fast-forward /rewind
View the picture during fast-
forward or rewind
m
Play at high speed
•
•
During playback, press M
remote commander.
During playback, hold down M
FF down or m
REW on the
FF or m
REW. When
you release the button, normal playback resumes.
Play at twice the normal speed During playback, press X2.
56 Playing/searching at various speeds
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback options
Play in slow motion
Play frame by frame
Operation
During playback, press y SLOW.
•
During pause, press M
FF down or m
REW on the
remote commander. Hold down M
FF or m REW to
play one frame each second.
Rewind and start play
During stop, hold m (rewind) down on the VCR and press H
(playback) on the VCR then release both.
To resume normal playback
Press H (playback).
Tip
•
Adjust the picture using the TRACKING +/– buttons if:
– Streaks appear while playing in slow motion.
– Bands appear at the top or bottom while pausing.
– The picture shakes while pausing.
To set tracking to the centre position, press both TRACKING +/– buttons at the same time.
Notes
•
•
•
The playback sound is muted during the operations in the above table.
In the LP mode, noise may appear or there may be no colour.
If the playback mode mark doesn’t appear on the TV screen, press
DISPLAY.
Playing/searching at various speeds 57
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the recording duration time
After you start recording in the normal way,
you can have the VCR stop recording
automatically after a specified duration.
z REC
While recording, press z REC.
1
The
indicator appears in the display window.
SP
VIDEO
OPC
PDC
Press z REC repeatedly to set the duration.
2
Each press advances the time in increments of 30 minutes.
Normal recording
0:30
1:00
5:30
6:00
The tape counter decreases minute by minute to 0:00, then the VCR stops
recording and turns off automatically.
To extend the duration
Press z REC repeatedly to set a new duration.
To cancel the duration
Press z REC repeatedly until the
indicator disappears and the VCR returns to
normal recording mode.
To stop recording
To stop the VCR while recording, press x STOP.
Note
•
You cannot display the current tape time in the display window when setting the recording
duration.
58 Setting the recording duration time
Download from Www.Somanuals.com. All Manuals Search And Download.
Synchronized Recording
You can set the VCR to automatically record programmes from equipment such as a
programmable set top box by connecting the equipment to the LINE-3 IN connector.
The connected equipment must have a timer function for this feature to work.
When the connected equipment turns on, the VCR also automatically turns on and
starts recording a programme from LINE-3 IN.
How to connect for Synchronized Recording.
Connect the LINE-3 IN of the VCR to the TV Scart connector of the Set-Top Box.
Then connect the LINE-1 (TV) connector to the TV.
Scart cable (not supplied)
TV Scart connector
Programmable
Set -Top Box
t LINE-3 IN
i LINE-1
(TV)
Scart (EURO-AV)
Scart cable (not supplied)
: Signal flow
continued
Synchronized Recording 59
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording programmes using
the Synchronized Recording
function
Before you start…
• Insert a tape with its safety tab in place.
Make sure the tape is longer than the total
recording time.
SP/LP
1
4
7
2
5
8
0
3
6
9
SYNCHRO REC
INPUT
SELECT
g
PROG +/-
Set the timer on the STB to the time of the programme you want to record, then
1 turn it off.
Press SP/LP to select the tape speed on the VCR.
2
Hold down SYNCHRO REC for more than two seconds.
3 The SYNCHRO REC indicator lights up on the front panel and the VCR stands
by for recording.
The VCR automatically turns on and starts recording when it receives an input
signal from the STB.
The VCR automatically stops recording when the tape reaches the end or when
the STB stops transmitting an input signal.
To cancel the Synchronized Recording function
Press SYNCHRO REC. The SYNCHRO REC indicator turns off.
To stop recording
Press x STOP while recording.
Notes
•
•
This function may not work with some types of satellite tuners.
If the settings for timer recording and Synchronized Recording overlap, the programme that
starts first has priority and the second programme starts recording only after the first
programme has finished.
•
The Auto Clock Set function does not work while the VCR stands by for Synchronized
Recording.
60 Synchronized Recording
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking/changing/cancelling timer
settings
Before you start…
• Turn on your TV and set it to the video
channel.
?/1
CLEAR
1
4
7
2
5
8
0
3
6
9
MENU
M/m/</,
OK
Press ?/1 to turn on the VCR.
1
2
Press MENU, then press M/m to highlight LISTS and press OK.
Press M/m to highlight TIMER LIST, then press
TIMER LIST
2 8 . 9 THU
3 OK:
VPS
PDC
DATE
TIME
PROG.
AAB
FGH
AAB
I J K
CDE
– –
TODAY
2 0 : 0 0 2 1 : 0 0
1 4 : 0 0 1 5 : 0 0
2 0 : 0 0 2 1 : 0 0
SP
LP
SP
LP
LP
–
MON
3 0 . 9
SUN
–
FRI
• If you want to change or cancel a setting, go
on to the next step.
• If you do not need to change or cancel the
settings, press MENU, then turn off the VCR
to return to recording standby.
6 : 3 0
7 : 0 0
VPS
PDC
2 . 1 0
1 0 : 0 0 1 1 : 3 0
– – . – –
– – . – –
– – . – –
RETURN
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– –
–
– –
–
SELECT
SET
CANCEL
:
: OK
:
CLEAR
EXIT : MENU
continued
Checking/changing/cancelling timer settings 61
Download from Www.Somanuals.com. All Manuals Search And Download.
Press M/m to select the setting you want to
TIMER
4 change or cancel, then press OK.
2 8 . 9 THU
DATE
TIME
PROG.
CDE
2 . 10
SP / LP
LIST
1 0 : 0 0 1 1 : 3 0
The selected setting appears in the TIMER
menu.
SP
VPS / PDC
ON
SELECT
:
:
:
SET
CANCEL
CLEAR
EXIT : MENU
• To change the setting, press </, to highlight the item you want to change,
and press M/m to change it.
• To cancel the setting, press CLEAR.
5
6
Press MENU.
If any settings remain, turn off the VCR to return to recording standby.
When the timer settings overlap
The programme that starts first has priority and the second programme starts
recording only after the first programme has finished. If the programmes start at the
same time, the programme listed first in the menu has priority.
Programme 1
Programme 2
about 20 seconds
will be cut off
Programme 1
Programme 2
about 20 seconds will be cut off
Tip
•
In step 5 above, you can check the TIMER LIST by selecting LIST and pressing OK. Press
MENU to exit the TIMER LIST.
62 Checking/changing/cancelling timer settings
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording stereo and bilingual
programmes
In ZWEITON (German stereo) system
This VCR automatically receives and records stereo and bilingual programmes based
on the ZWEITON system. When a stereo or bilingual programme is received, the
STEREO indicator appears in the display window.
To select bilingual sound while recording
Press AUDIO MONITOR to select the sound you want.
To listen to
Main
On-screen display
MAIN
Display window
STEREO
Sub
SUB
STEREO
Main and sub
MAIN/SUB
STEREO
In NICAM system
This VCR receives and records stereo and bilingual programmes based on the
NICAM system (the NICAM indicator appears). When a stereo or bilingual
programme is received, the STEREO indicator appears in the display window.
To record a NICAM programme, HIFI AUDIO in the AUDIO OPTIONS menu
should be set to NICAM (initial setting). To check the menu setting, see page 69 for
details.
To select the sound while recording
Press AUDIO MONITOR to select the sound you want.
Stereo programme
To listen to
Stereo
On-screen display
STEREO
Display window
STEREO
Standard sound*
No indicator
No indicator
*
Usually the mixed sound of left and right channels (monaural)
Bilingual programme
To listen to
Main
On-screen display
MAIN
Display window
STEREO
Sub
SUB
STEREO
Main and sub
Standard sound*
MAIN/SUB
No indicator
STEREO
No indicator
*
Usually the main sound (monaural)
continued
Recording stereo and bilingual programmes 63
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the sound during playback
Press AUDIO MONITOR to select the sound you want.
To listen to
On-screen display
Display window
Stereo/main and sub (left and STEREO
right channels)
STEREO
Left channel/main
Right channel/sub
Standard sound
LCH
STEREO
RCH
STEREO
No indicator
No indicator
How sound is recorded on a video tape
The VCR records sound onto two separate tracks. Hi-fi audio is recorded onto the
main track along with the picture. Monaural sound is recorded onto the normal audio
track along the edge of the tape.
Stereo
Bilingual
Usually mixed
left/right channels
Usually main sound
Normal audio track
(monaural)
Hi-fi audio track
(main track)
Stereo sound
(left/right channels)
Main (left channel)
Sub (right channel)
Notes
•
•
•
•
To listen to playback sounds in stereo, you must use the EURO-AV or AUDIO OUT
connections.
When you play a tape recorded in monaural, the sound is heard in monaural regardless of the
AUDIO MONITOR setting.
If the AUDIO MONITOR button does not function, check that AUDIO MIX in the AUDIO
OPTIONS menu is set to OFF (see page 69).
If HIFI AUDIO is set to STANDARD, the standard sound will be recorded on both the hi-fi
and normal audio tracks. Pressing AUDIO MONITOR will not change the sound.
64 Recording stereo and bilingual programmes
Download from Www.Somanuals.com. All Manuals Search And Download.
Searching using the index function
The VCR marks the tape with an index signal
at the point where each recording begins. Use
these signals as references to find a specific
recording. The VCR can search up to 99
index signals ahead or behind the current
position.
./>
INDEX
SEARCH
1
2
3
Insert an indexed tape into the VCR.
1
Press ./> INDEX SEARCH repeatedly to
2 specify how many index signals ahead or behind
you want to search :
INDEX
SEARCH
2
• To search ahead, press > INDEX
SEARCH.
• To search backwards, press . INDEX
SEARCH.
The VCR starts searching and the index number
on the TV screen counts down to zero. Playback
starts automatically from that point.
To stop searching
Press x STOP.
Note
•
No index signal will be added when recording starts from recording pause. However, an
index signal will be marked if you change the programme position during recording pause.
Searching using the index function 65
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the picture
Adjusting the tracking
Although the VCR automatically adjusts the
tracking when playing a tape (the indicator
flashes in the display window, then goes off),
distortion may occur if the tape was recorded in poor
condition. In this case, manually adjust the tracking.
During playback, press TRACKING +/– to display
the tracking meter. The distortion should disappear
as you press one of the two buttons (the indicator
lights up). To resume automatic tracking
TRACKING
Tracking meter
adjustments, eject the tape and re-insert it.
To set the tracking to the centre position, press
TRACKING + and – buttons at the same time.
About the Reality Regenerator (RR) function
The Reality Regenerator (RR) function automatically restores the picture to its
original quality during playback.
To use the RR function, press
REALITY REGENERATOR button.
The REALITY REGENERATOR
indicator lights up. You can set RR to
g
HIGH or NORMAL in the VIDEO
OPTIONS menu (see page 68).
To turn it off, press REALITY
REGENERATOR indicator lights off.
About the Optimum Picture Control (OPC) function
The Optimum Picture Control (OPC) function
VIDEO OPTIONS
automatically improves recording and playback
OPC
EDIT
ON
OFF
quality by adjusting the VCR to the condition of the
video heads and tape. To maintain better picture
quality, we recommend that you set OPC to ON in
the VIDEO OPTIONS menu (with the OPC
indicator in the display window lit). For details, see
page 68.
SHARPNESS
COLOUR SYSTEM
RR
NORMAL
AUTO
NORMAL
RETURN
SELECT
SET
:
: OK
EXIT : MENU
OPC playback
The OPC function automatically works on all types of tapes, including rental tapes
and tapes that were not recorded with OPC.
66 Adjusting the picture
Download from Www.Somanuals.com. All Manuals Search And Download.
OPC recording
Whenever you insert a tape and start recording for the first time, the VCR adjusts to
the tape using the OPC function (the OPC indicator flashes rapidly). This adjustment
is retained until the tape is ejected.
To deactivate the OPC function
Set OPC to OFF in the VIDEO OPTIONS menu. The OPC indicator in the display
window turns off.
Notes
•
With the Auto Long Play function ON, the OPC function will work only in SP mode. If the
tape speed automatically switches from SP to LP, the OPC function turns off. However, if the
entire programme is recorded in LP mode, the OPC function will work.
•
There is a delay of about ten seconds before the VCR actually starts recording while the VCR
analyses the tape. To avoid the delay, first set the VCR to recording pause (the OPC indicator
flashes slowly) and press z REC to have the VCR analyse the tape (the OPC indicator
flashes rapidly) and returns to recording pause. After the OPC indicator stops flashing, press
X PAUSE to start recording immediately. If you want to start recording quickly without
using the OPC function, first set the VCR to recording pause (the OPC indicator flashes
slowly) and press X PAUSE to start recording.
Adjusting the picture 67
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing menu options
Press MENU, then select OPTIONS and press
OPTIONS
1 OK.
VIDEO OPTIONS
AUDIO OPTIONS
TAPE OPTIONS
OTHER OPTIONS
RETURN
SELECT
SET
:
: OK
EXIT : MENU
Press M/m to highlight the kind of option to change, VIDEO OPTIONS, AUDIO
2 OPTIONS, TAPE OPTIONS or OTHER OPTIONS, then press OK
Press M/m to select the option, then press OK to enter the pop up menu.
3
Press M/m to select the desired setting, then press OK.
4
Press MENU to exit the menu.
5
VIDEO OPTIONS menu
VIDEO OPTIONS
Initial settings are indicated in bold print.
OPC
ON
EDIT
OFF
SHARPNESS
COLOUR SYSTEM
RR
NORMAL
AUTO
NORMAL
RETURN
SELECT
SET
:
: OK
EXIT : MENU
Menu option
Set this option to
OPC
• ON to switch on the OPC (Optimum Picture Control) function
and improve picture quality.
•
•
OFF to switch off OPC.
EDIT
ON to minimize picture deterioration when editing.
• OFF to turn off EDIT.
LOW to playback a poor quality tape.
• NORMAL to playback an average quality tape.
HIGH to playback a good quality tape.
• AUTO to detect automatically the colour system of a tape.
SHARPNESS
•
•
COLOUR SYSTEM
•
•
PAL to playback a tape recorded in the PAL system.
MESECAM to playback a tape recorded in the MESECAM
system.
RR
• NORMAL for normal everyday use.
•
HIGH for well-used video tapes such as rented tapes. Select this
option when NORMAL does not improve the picture quality.
For details, see page 66.
Note
•
When you playback with the EDIT function ON, the OPC and the SHARPNESS functions
don’t work.
68 Changing menu options
Download from Www.Somanuals.com. All Manuals Search And Download.
•
When you turn off your VCR or eject the tape, the colour system is set automatically to
AUTO.
AUDIO OPTIONS menu
Initial settings are indicated in bold print.
AUDIO OPTIONS
AUDIO MIX
HIFI AUDIO
RETURN
OFF
NICAM
SELECT
SET
:
: OK
EXIT : MENU
Menu option
Set this option to
AUDIO MIX
•
ON to listen to the hi-fi and normal audio tracks at the same
time. The AUDIO MONITOR button will not function.
• OFF to listen to the hi-fi and normal audio tracks separately.
Select the sound using the AUDIO MONITOR button.
For details, see page 63.
HIFI AUDIO
•
STANDARD to record standard sound on the hi-fi audio track.
• NICAM to record NICAM broadcasts on the hi-fi audio track.
For details, see page 63.
Note
•
If you eject the tape, AUDIO MIX is automatically set to OFF.
TAPE OPTIONS menu
Initial settings are indicated in bold print.
TAPE OPTIONS
AUTO LONG PLAY
TAPE LENGTH
RETURN
OFF
E180
SELECT
SET
:
: OK
EXIT : MENU
Menu option
Set this option to
AUTO LONG PLAY
•
ON to automatically record from SP (Standard Play) to LP
(Long Play) when the tape length is not long enough.
• OFF to normally record in SP (Standard Play).
TAPE LENGTH
• E180 to use an E-180 or shorter tape type.
•
•
•
E195 to use an E-195.
E240 to use an E-240.
E300 to use an E-300.
continued
Changing menu options 69
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER OPTIONS menu
OTHER OPTIONS
Initial settings are indicated in bold print.
BUZZER
ON
DIMMER
OFF
DECODER/LINE3
POWER SAVE
TIMER OPTIONS
TV DIRECT REC
RETURN
DECODER
OFF
VARIABLE
ON
SELECT
SET
:
: OK
EXIT : MENU
Menu option
Set this option to
BUZZER
• ON to output a beep sound.
•
OFF to deactivate it.
DIMMER
•
ON to make the display window dim.
• OFF to make it brighter.
DECODER/LINE3
• DECODER to use the DECODER/LINE-3 IN connector as the
PAY-TV/Canal Plus decoder connector.
•
•
LINE3 to use the DECODER/LINE-3 IN connector as a line
input connector.
POWER SAVE
ON to turn off the indicators in the display window to save the
VCR power.
• OFF to turn on the indicators in the display window while the
VCR is standing by.
TIMER OPTIONS
• VARIABLE to display the TIMER METHOD menu for
selecting STANDARD or SHOWVIEW when pressing the
TIMER button.
•
STANDARD to display only the TIMER menu when pressing
the TIMER button.
SHOWVIEW to display only the SHOWVIEW menu when
pressing the TIMER button.
•
For details, see page 48 and 53.
TV DIRECT REC
• ON to activate the TV Direct Rec function.
•
OFF to deactivate it.
Note
•
When you set a timer recording or a sychronized recording, the indicators in the display
window remain on, even though POWER SAVE is set to ON.
70 Changing menu options
Download from Www.Somanuals.com. All Manuals Search And Download.
Editing
Connecting to a VCR or stereo system
How to connect to record on your VCR
Connect the line outputs of the other VCR to the LINE IN connector or jacks of your
VCR. Refer to the examples A or B and choose the connection that best suits your
VCR.
Example A
Your VCR (Recorder)
TV
t DECODER/
LINE-3 IN
Other VCR (Player)
Scart
(EURO-AV)
VMC-2121HG Scart cable (not supplied)
: Signal flow
Example B
TV
Your VCR (Recorder)
g
LINE-2 IN
Other VCR (Player)
LINE OUT
VMC-820 audio/video cable
(not supplied)
: Signal flow
continued
Connecting to a VCR or stereo system 71
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
You can also use the LINE-3 IN connector instead.
Notes
•
•
•
Make sure you connect the plugs to jacks of the same colour.
If the other VCR is a monaural type, leave the red plugs unconnected.
If you connect your VCR to both the LINE IN and LINE OUT jacks of the other VCR, select
the input correctly to prevent a humming noise.
•
•
If the other VCR does not have a Scart (EURO-AV) connector, use the VMC-2106HG cable
instead and connect the cable to the line out jacks of the other VCR.
When you connect another VCR to the DECODER/LINE3 IN connector, set DECODER/
LINE3 to LINE3 in the OTHER OPTIONS menu.
How to connect to a stereo system
Connect the LINE-2 IN AUDIO L/R jacks of your VCR to the audio output jacks on
the stereo system, using the RK-C510HG audio cable (not supplied).
72 Connecting to a VCR or stereo system
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Editing
z
(when recording on your VCR)
g
Before you start editing...
X
• Turn on your TV and set it to the video
channel. Press INPUT SELECT to display
“L2” (or “L1” or “L3”) in the display
window.
VIDEO OPTIONS
OPC
EDIT
ON
ON
SHARPNESS
COLOUR SYSTEM
RR
NORMAL
AUTO
NORMAL
RETURN
• Press SP/LP to select the tape speed, SP or
LP.
SELECT
SET
:
: OK
• On your VCR, set EDIT to ON in the
VIDEO OPTIONS menu to display
“EDIT” in the display window. If the other
VCR has a similar feature, activate this one
as well.
EXIT : MENU
Insert a source tape with its safety tab removed into the other (playback) VCR.
1 Search for the point to start playback and set it to playback pause.
Insert a tape with its safety tab in place into your (recording) VCR. Search for
2 the point to start recording and press X (pause).
Press z (record) on your VCR to set it to recording pause.
3
To start editing, press the X (pause) buttons on both VCRs at the same time.
4
To stop editing
Press the x (stop) buttons on both VCRs.
Tip
•
To cut out unwanted scenes while editing, press X (pause) on your VCR when an unwanted
scene begins. When it ends, press X (pause) again to resume recording.
Note
If you start editing following the procedure above, the VCR won’t start recording with the
•
OPC function. To record a tape with the OPC function, press z (record) again during
recording pause in step 3 so the VCR analyses the tape. Then press X (pause) after the OPC
indicator stops flashing to start recording. If you press X (pause) before the OPC indicator
stops flashing, the OPC function is cancelled.
Basic Editing 73
Download from Www.Somanuals.com. All Manuals Search And Download.
SmartFile function
About the SmartFile function
SmartFile allows you to view the contents of your video tape (recording date,
channel, name etc.) on the TV screen. It is no longer necessary to rewind, fast-
forward, or playback a tape to find out what is recorded on it. You can also locate and
start playback of a specific programme or find the place from which you want to start
recording by using this list. Programme data is stored in the memory of the SmartFile
label attached to the tape.
The following functions are possible using SmartFile :
Recording using the SmartFile function (page 76)
To use the SmartFile function, attach the SmartFile
label to the tape. If you record a programme on a tape
with a SmartFile label, the contents will appear on the
SmartFile search list. With the SmartFile list, you can
also easily find the beginning of the available
recording space.
SmartFile search list
2 . 8 . 00 - 10 . 10 . 00
PAGE 1
BLANK TIME
SP 1H 55M
10 . 10 SPORTS FESTIVAL
SPORTS CCB SP 1H 30M
1 . 10 NEWS SEVEN
SP 0H 30M
30 .
FILMS
9
SAT
7 : 00 PROG .32
START
SELECT
END
:
SEARCH : OK
EXIT : MENU
Selecting and playing a programme (page 81)
To playback a recorded programme, select the programme you want to watch using
the SmartFile search list. The VCR locates the programme and playback starts
automatically.
Checking the contents of a tape (page 82)
When you bring the SmartFile label close to the
SMARTFILE sensor on the VCR, a summary of
the recorded programmes appears in the SmartFile
check list. It is not necessary to insert the tape into
g
the VCR and press H PLAY to find out what is
recorded on it. This feature allows you to easily
find the programme you want to watch, or to
quickly find a tape with enough recording space.
SmartFile check list
2 . 8 . 00 - 10 . 10 . 00
PAGE 1
BLANK TIME
SP 1H 55M
10 . 10 SPORTS FESTIVAL
1 . 10 NEWS SEVEN
30 .
22 .
10 .
2 .
9
9
9
9
SAT
FRI 1 2 : 00 SARU
9 : 00
7 : 00 PROG .32
SUN
STB098
SAT 2 3 : 00 STB
NEXT
:
EXIT : MENU
74 About the SmartFile function
Download from Www.Somanuals.com. All Manuals Search And Download.
Labelling a recorded programme and tape (page 84)
You can attach an electronic "label" to the video tape and its programmes on the
SmartFile list. Labelling the recorded programmes enables you to find a programme
easily when you want to play it back. If TV guide pages are available in the Teletext,
recorded programmes are labelled automatically. Also, once you label a programme
which you set to record regularly (i.e everyday, same day of the week), the VCR
recognizes the label and will automatically label all future recordings of the same
programme.
Registering the contents of a recorded tape in the
SmartFile label (page 92)
You can register programmes recorded on a tape in the memory of a new SmartFile
label.
Protecting a recorded programme (page 94)
You can protect a recorded programme from accidental over-recording or erasure.
Erasing the data of an unwanted programme (page 96)
By erasing a programme from the SmartFile list, the VCR will record over the
unwanted programme.
Running a demonstration
This VCR can give a demonstration
g
of the various SmartFile functions.
To run a demonstration, turn on the
VCR and hold the SMARTFILE
SMARTFILE
button for 3 seconds while no tape is
inserted. To stop the demonstration,
press any key.
About the SmartFile function 75
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording using the SmartFile function
To use the SmartFile function, attach the SmartFile label to the spine of the cassette.
If you record a programme for more than 20 minutes in LP mode and 11 minutes in
SP mode on a tape with a SmartFile label, programme data, such as the name, date
and channel, is automatically stored in the memory of the SmartFile label. Some
stations may not offer this service.
Attaching the SmartFile label to the cassette
To use the SmartFile function, attach the supplied
SmartFile label to the cassette. Remove any stains
or dirt from the surface of the spine of the tape.
Then, holding both edges of the SmartFile label so
that it doesn’t bend, attach it along the guide line
to the spine of the cassette. This tape is henceforth
SMARTFILE SENSOR
referred to as a SmartFile tape.
Note on the purchase of SmartFile labels
•
If you want to order additional SmartFile labels, contact your nearest Sony service facility.
Notes
•
The SmartFile label is equipped with a memory chip. The memory chip may be dammaged
and cannot be used when you:
- twist or fold the SmartFile label.
- remove the SmartFile label and re-attach it to a tape.
- attach more than one SmartFile label to a tape.
- attach metal, or sticker which has metal, to the SmartFile label.
- write too strongly on the SmartFile label using a ballpoint pen or similar sharp instrument.
- disassemble or remodel a label.
•
•
Do not leave the SmartFile label in a place subject to excessive dust or dirt, direct sunlight,
humidity, mildew, strong magnetism or near heat sources.
If you attach the SmartFile label to a tape shorter than an E-30, the SmartFile function may
not work correctly.
76 Recording using the SmartFile function
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording a programme on the SmartFile tape
0
When recording a programme on the
SmartFile tape, no matter what method you
use to record the programme (normal
recording, showview recording, etc.),
programme data (date, name, channel,
recording start time , etc.) is stored in the
memory of the SmartFile label. The
SmartFile label can contain data for up to 12
programmes. When the number of stored
programmes goes over 12, the oldest
programme data is erased from the
SMARTFILE
M/m/</,
OK
SmartFile list. However, a programme
which lasts less than about 20 minutes in LP
mode or about 11 minutes in SP mode
cannot be stored in the memory. When you
record a programme on a SmartFile tape
which already contains programme data,
see “Recording after locating the Blank
Time space” on page 79.
Before you start…
• Turn on your TV and set it to the video channel
• Check that the VCR clock is set to the correct time and date.
Insert a SmartFile tape with its safety tab in place. The SmartFile indicator lights
1 up.
Press SMARTFILE.
PAGE 1
SP 1H 55M
2 The SmartFile search list appears on the TV
BLANK TIME
screen.
START
END
Use M to select BLANKTIME and press OK.
3 The VCR starts searching for the longest blank part of the tape. The SmartFile
search list disappears.
You can now start recording a programme.
Tip
•
You can protect a recorded programme from accidental over-recording or erasures(see page
94.)
Note
If you press the PAUSE button one or more times during recording, thereby creating short
•
lengths of recorded time between such pauses, programme data may not be stored in the
SmartFile label.
continued
Recording using the SmartFile function 77
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the information of a recorded programme
Press SMARTFILE. The SmartFile search list appears. The recording day of the
week, start time, programme position, date, name, recording time and tape speed
appear on the list.The longest space which doesn’t have any programme data (Blank
Time space) appears as "BLANK TIME":
Initial and latest dates of use
for this SmartFile tape
Recording start time
2 . 8 . 00 - 10 . 10 . 00
BLANK TIME
PAGE 1
SP 1H 55M
Remaining time
Programme position *
30 .
9
SAT
7 : 00
CCB
Date
SP 1H 30M
Day of the week
Recording time
Tape speed
Estimated position
of the recorded
programme
START
END
SELECT
:
SEARCH : OK
EXIT : MENU
Station name*
* When the station name is not available, the programme position is displayed
instead.
Tip
•
You can manually name a recorded programme and select the category. You can also name
the SmartFile tape.
Notes
•
•
•
If you don’t set the clock or the clock isn’t set to the correct time and date, the recording start
time won’t be stored correctly on the Smartfile list. Also the programme label won’t be stored
correctly if the TV guide page information of Teletext is not set correctly (see page 76).
When you set the AUTO LONG PLAY option to ON in the TAPE OPTIONS menu, and the
tape speed automatically changes from SP to LP during recording, the VCR displays the
entire recording time converted to SP mode in the SmartFile list.
The recording time length in the SmartFile list is an estimation and may be slightly different
from the actual recorded time lenght.
78 Recording using the SmartFile function
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording after locating the Blank Time space
The SmartFile function identifies not only
the largest amount of available blank space,
but also recorded material that doesn’t have
corresponding programme data stored in the
SmartFile label. The longest available
recording space (including programmes that
are not stored on the SmartFile label) is
referred to as "Blank Time space". You can
locate the beginning of the Blank Time
space for recording. If there is a recorded
programme after the Blank Time space, the
SP/LP
VCR will record over on that programme
unless you stop recording. If there is a
programme you want to prevent from being
recorded over or erased, protect that
programme before you start recording
another programme see page 94.
1
4
7
2
5
8
0
3
6
9
Before you start…
• Turn on your TV and set it to the video
channel.
SMARTFILE
M/m/</,
OK
Insert a SmartFile tape with its safety tab in place.
1 The SMARTFILE indicator lights up on the VCR.
Press SMARTFILE.
2 . 8 . 00 - 10 . 10 . 00
BLANK TIME
10 . 10 SPORTS FESTIVAL
SPORTS CCB SP 1H 30M
1 . 10 NEWS SEVEN
SP 0H 30M
PAGE 1
SP 1H 55M
2 The SmartFile search list appears on the TV
screen. The Blank Time space appears in the
"BLANK TIME" row.
30 .
FILMS
9
SAT
7 : 00 PROG .32
SP 1H 30M
The Blank Time space also appears in the
display window.
START
SELECT
END
:
SEARCH : OK
EXIT : MENU
Press M repeatedly to select BLANK TIME.
3
continued
Recording using the SmartFile function 79
Download from Www.Somanuals.com. All Manuals Search And Download.
Press SP/LP to select the tape speed, SP or LP.
2 . 8 . 00 - 10 . 10 . 00
BLANK TIME
10 . 10 SPORTS FESTIVAL
SPORTS CCB SP 1H 30M
1 . 10 NEWS SEVEN
SP 0H 30M
PAGE 1
LP 3H 50M
4
5
The BLANK TIME changes according to the
selected tape speed. Select a tape speed that
matches the length of the programme you want
to record.
30 .
FILMS
9
SAT
7 : 00 PROG .32
SP 1H 30M
START
SELECT
END
:
SEARCH : OK
EXIT : MENU
PAGE 1
Press OK.
2 . 8 . 00 - 10 . 10 . 00
The VCR goes to the beginning of the Blank
Time space and stops.
NOW SEARCHING
START
END
Press PROG +/– to select the programme position you want to record.
6
7
Press z REC to start recording.
Notes
•
You may not be able to locate the beginning of the Blank Time space correctly in the step 4
above when :
- the SmartFile tape contains one or more short length (less than about 20 minutes in the LP
mode and about 11 minutes in the SP mode) programmes for which programme data is not
stored in the SmartFile label.
- the SmartFile tape is damaged or dirty.
- the SmartFile tape has a portion recorded in the NTSC system.
•
If a newly recorded programme overlaps a stored programme, the stored programme
information is erased from the SmartFile list as shown below when :
- the remaining length of the stored programme becomes less than about 20 minutes in the LP
mode and about 11 minutes in the SP mode.
- the stored programme is over-recorded for more than 20 minutes in the LP mode and about
11 minutes in the SP mode.
necessary portion
unnecessary portion
Stored programme
Newly recorded
programme
or
or
20 minutes in the LP mode
11 minutes in the SP mode
80 Recording using the SmartFile function
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting and playing a programme
You can automatically locate and start
playback of a programme recorded on the
SmartFile tape. Select a programme in the
SmartFile search list. The SmartFile search
list can contain up to 12 programmes.
SMARTFILE
M/m/</,
OK
Before you start…
• Turn on your TV and set it to the video
channel.
Insert a SmartFile tape.
1 The SMARTFILE indicator lights up on the VCR.
Press SMARTFILE.
2 . 8 . 00 - 10 . 10 . 00
BLANK TIME
10 . 10 SPORTS FESTIVAL
SPORTS CCB SP 1H 30M
1 . 10 NEWS SEVEN
SP 0H 30M
PAGE 1
SP 1H 55M
2 The SmartFile search list appears on the TV
screen.
30 .
FILMS
9
SAT
7 : 00 PROG .32
SP 1H 30M
START
SELECT
END
:
SEARCH : OK
EXIT : MENU
Press M/m to select a programme.
2 . 8 . 00 - 10 . 10 . 00
BLANK TIME
10 . 10 SPORTS FESTIVAL
SPORTS CCB SP 1H 30M
1 . 10 NEWS SEVEN
SP 0H 30M
PAGE 1
3
SP 1H 55M
Press M/m repeatedly to turn the pages.
30 .
FILMS
9
SAT
7 : 00 PROG .32
SP 1H 30M
START
SELECT
END
:
SEARCH : OK
EXIT : MENU
Press OK.
4
The VCR starts searching for the beginning of the selected programme.
Playback starts automatically from that point.
To stop searching
Press x STOP.
Note
•
You may not be able to locate the beginning of the selected programme correctly when :
- the SmartFile tape contains one or more short length (less than about 20 minutes in the LP
mode and about 11 minutes in SP mode) programmes for which programme data is not
stored in the SmartFile label.
- the SmartFile tape is damaged or dirty.
- the SmartFile tape has a portion recorded in the NTSC system.
Selecting and playing a programme 81
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the contents of a tape
You can display the programme data list of
a SmartFile tape on the TV screen. It is not
SmartFile sensor
necessary to insert the tape into the VCR.
This feature allows you to quickly find a
specific programme or to find a tape with
enough recording space. The SmartFile
g
check list can contain up to 12 programmes.
Before you start…
CURSOR M/m
• Turn on your TV and set it to the video
channel.
• Turn on your VCR.
Hold the label side of the SmartFile tape close to
1 the SmartFile sensor.
Slowly bring the center of the label within 3 cm
of the SmartFile sensor.
g
There is a short beep, the SMARTFILE indicator
lights up on the VCR, and the SmartFile check
list appears. The BLANK TIME space also
appears in the display window.
2 . 8 . 00 - 10 . 10 . 00
BLANK TIME
10 . 10 SPORTS FESTIVAL
1 . 10 NEWS SEVEN
PAGE 1
SP 1H 55M
30 .
22 .
10 .
2 .
9
9
9
9
SAT
FRI 1 2 : 00 SARU
9 : 00
7 : 00 PROG .32
SUN
STB098
SAT 2 3 : 00 STB
NEXT
:
EXIT : MENU
AUTO SET UP
SMARTLINK SPEP
OPC
LP
STEREO
TV NICAM
VIDEO
VPS
PDC
DNR
BL
EDIT
H
M
S
Press CURSOR M/m to turn the pages.
2 . 8 . 00 - 10 . 10 . 00
BLANK TIME
PAGE 2
2
3
SP 1H 55M
31 .
2 .
8
8
24HOURS TV
GOLF
BACK
:
EXIT : MENU
Press MENU to exit the SmartFile check list.
82 Checking the contents of a tape
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
•
If you press any button other than SP/LP or M/m, the SmartFile check list disappears.
Notes
•
You cannot display the SmartFile check list while :
- you display the SmartFile list of a different SmartFile tape inserted into the VCR.
- you display any other menu.
•
•
If the SmartFile check list doesn’t appear on the TV screen, try drawing the SmartFile tape at
least 5 cm away from the SmarFile sensor, then bring it back to within 3 cm of the sensor.
The menu disappears automatically if you don’t proceed for more than a few minutes.
Checking the contents of a tape 83
Download from Www.Somanuals.com. All Manuals Search And Download.
Labelling a recorded programme and tape
Some broadcast systems ensure a Teletext
Tape title
service in which the complete programmes
and their data (title, date, channel, recording
start time etc.) are stored day by day. A TV
guide page corresponds to each day of the
week. When recording a programme, the
VCR automatically takes the label
information from the Teletext pages and
stores it in the SmartFile label. The TV guide
page numbers depend entirely on the
broadcast itself and may be subject to
change. If so, you may have to set those TV
guide page numbers manually in the TV
GUIDE PAGE menu.
MY VIDEO TAPE
BLANK TIME
PAGE 1
SP 1H 55M
10 . 10 SPORTS FESTIVAL
SPORTS CCB SP 1H 30M
Category
Programme
label
START
END
SELECT
:
SEARCH : OK
EXIT : MENU
Setting the TV guide page number
CLEAR
Before you start…
• Turn on your TV and set it to the video
1
4
7
2
5
8
0
3
6
9
channel.
Programme
number
buttons
PROG +/–
MENU
M/m/</,
OK
84 Labelling a recorded programme and tape
Download from Www.Somanuals.com. All Manuals Search And Download.
Select the programme position for which you want to set or change the TV guide
1 page.
Press MENU, then press M/m to highlight SETTINGS and press OK.
2
Press M/m to highlight TV GUIDE PAGE and
SETTINGS
3 press OK.
TUNER
CLOCK
LANGUAGE
TV GUIDE PAGE
RETURN
• The TV guide page numbers appear
automatically when the VCR detects them
(P301).
• If the VCR does not detect them (P---), you
have to set the TV guide page number
manually.
SELECT
SET
:
: OK
EXIT : MENU
PROG . 5
TV GUIDE PAGE
SUN
MON
TUE
WED
THU
FRI
P - - -
P - - -
P - - -
P - - -
P - - -
P - - -
P - - -
SAT
SELECT
SET
:
: OK
EXIT : MENU
Press M/m to select the TV guide page number
4 you want to modify and press OK.
TV GUIDE PAGE
PROG . 5
SUN
MON
TUE
WED
THU
FRI
P - - -
P - - -
P - - -
P - - -
P - - -
P - - -
SAT
SET
CONFIRM : OK
CANCEL CLEAR
:
0–9
:
EXIT : MENU
Press the programme number buttons to enter
5 the TV guide page number and press OK to
TV GUIDE PAGE
PROG . 5
SUN
MON
TUE
WED
THU
FRI
P 3 0 1
confirm the setting.
P - - -
P - - -
P - - -
P - - -
P - - -
P - - -
If you make a mistake, press CLEAR to re-enter
the correct number.
SAT
SELECT
SET
:
: OK
EXIT : MENU
To set or change another TV guide page number, repeat steps 3 and 4 above.
Press MENU to exit the menu.
6
7
continued
Labelling a recorded programme and tape 85
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
•
In step 4 above, enter "000" if you don’t want to use the TV guide page number for automatic
labelling. The VCR will instead store default data (date, programme position, duration etc.)
in the label.
•
•
•
Refer to the Teletext information on your TV screen to get the TV guide page number with
the programme titles and their start times.
If the Teletext TV guide has a page which always shows the programmes for the current day,
this page should be input for all days.
If you start recording more than two minutes before the programme is scheduled to start, the
correct label information may not be transferred. The VCR receives the label information two
minutes after the recording starts.
•
•
•
If you set a timer recording with VPS/PDC OFF, the title information will be transferred in
the middle of the recording.
Note that this function may not work correctly with programmes broadcast from some
stations.
If the Broadcast system updates the Teletext information at the moment recording starts, the
title on the label may not correspond to the one of the recorded programme. In this case, you
may have to manually enter the correct title using the SMARTFILE EDIT MENU.
•
You cannot get the label information from sources connected to the LINE input or the
satellite channels.
86 Labelling a recorded programme and tape
Download from Www.Somanuals.com. All Manuals Search And Download.
Labelling a recorded programme manually
If Teletext data is not available, label and
select the appropriate category of the
recorded programme manually. Labelling
CLEAR
manually takes priority over labelling
automatically. You can also label the tape.
Up to 18 characters can be input for a
programme and tape label.
1
4
7
2
5
8
0
3
6
9
MENU
M/m/</,
OK
Before you start…
• Turn on your TV and set it to the video channel.
Insert a SmartFile tape.
1
The SMARTFILE indicator lights up on the VCR.
Press MENU and select SMARTFILE EDIT and
SMARTFILE EDIT
2 press OK.
PAGE 1
2 . 8 . 00 - 10 . 10. 00
10 . 10 SPORTS FESTIVAL
SPORTS
1 . 10 NEWS SEVEN
SP 1H 30M
CCB
SP 1H 30M
The SMARTFILE EDIT menu appears.
30 .
FILMS
9
SAT
7 : 00 PROG .32
SP 1H 30M
SELECT
CATEGORY
TITLE
:
:
:
EXIT : MENU
continued
Labelling a recorded programme and tape 87
Download from Www.Somanuals.com. All Manuals Search And Download.
Press M/m to select a programme.
SMARTFILE EDIT
3
4
5
PAGE 1
2 . 8 . 00 - 10 . 10. 00
10 . 10 SPORTS FESTIVAL
SPORTS
1 . 10 NEWS SEVEN
SP 1H 30M
CCB
SP 1H 30M
30 .
FILMS
9
SAT
7 : 00 PROG .32
SP 1H 30M
SELECT
CATEGORY
TITLE
:
:
:
EXIT : MENU
Press ,.
SMARTFILE EDIT
PAGE 1
2 . 8 . 00 - 10 . 10. 00
10 . 10 SPORTS FESTIVAL
The cursor moves to the programme label input
position.
SPORTS
1 . 10 NEWS SEVEN
SP 1H 30M
CCB
SP 1H 30M
30 .
9
FILMS
SP 1H 30M
SELECT
BACK
CONFIRM
:
:
NEXT
:
: OK
EXIT : MENU
Label the programme.
SMARTFILE EDIT
PAGE 1
2 . 8 . 00 - 10 . 10. 00
1 Press M/m to select a character.
Each time you press M, the character changes
as shown below.
10 . 10 SPORTS FESTIVAL
SPORTS
CCB
SP 1H 30M
1 . 10 NEWS SEVEN
SP 1H 30M
SP 1H 30M
30 .
9
N
FILMS
At Bt ... t Z t special characters t
! t& t, (comma) t - (hyphen) t .
(period) t 0 t 1 ... t9 t(blank space)
You can also select a blank space by pressing
CLEAR.
SELECT
BACK
CONFIRM
:
:
NEXT
:
: OK
EXIT : MENU
2 To set the next character, press ,.
SMARTFILE EDIT
PAGE 1
The cursor moves to the next position.
2 . 8 . 00 - 10 . 10. 00
10 . 10 SPORTS FESTIVAL
SPORTS
CCB
SP 1H 30M
1 . 10 NEWS SEVEN
SP 1H 30M
SP 1H 30M
3 Repeat steps 1 and 2 to label the programme.
30 .
FILMS
9
N
SELECT
BACK
CONFIRM
:
:
NEXT
:
: OK
EXIT : MENU
Press OK.
SMARTFILE EDIT
6
PAGE 1
2 . 8 . 00 - 10 . 10. 00
10 . 10 SPORTS FESTIVAL
SPORTS
CCB
SP 1H 30M
1 . 10 NEWS SEVEN
SP 1H 30M
SP 1H 30M
30 .
FILMS
9
NICK & MATT
SELECT
CONFIRM
:
: OK
EXIT : MENU
88 Labelling a recorded programme and tape
Download from Www.Somanuals.com. All Manuals Search And Download.
Press M/m to select a category.
SMARTFILE EDIT
7
PAGE 1
2 . 8 . 00 - 10 . 10. 00
Each time you press M, the category changes as
shown below.
10 . 10 SPORTS FESTIVAL
SPORTS
1 . 10 NEWS SEVEN
SP 1H 30M
CCB
SP 1H 30M
30 .
9
NICK & MATT
SHOW
SP 1H 30M
SPECIAL t FILMS t NEWS t SHOW
SPORTS t CHILDREN t MUSICt
ARTS t SERIES t EDUCATION t
LEISURE t SHOPPING t VARIETY t
(blank)
SELECT
CONFIRM
:
:
OK
EXIT : MENU
Press OK.
8
9
The programme label and a selected category are stored.
Press MENU to exit the menu.
To erase the programme label
Press CLEAR after step 3 above. The programme label is erased and the default
recording data reappear.
To erase the selected category
Press CLEAR in step 7 above. The selected category is erased and the space becomes
blank.
To label a regularly scheduled timer-recorded programme
Once you label a programme which is set to record regularly (i.e everyday, same day
of the week) in the ShowView system or timer recording mode, the VCR recognizes
the label and will automatically label all future recordings of the same programme.
The set label is assigned even when an information signal containing the programme
name, category name or other information is broadcast with the programme.
However, if you change the programme label and the category several times, the VCR
may automatically assign the set label only to the last recorded programme for which
the programme label and category were changed.
continued
Labelling a recorded programme and tape 89
Download from Www.Somanuals.com. All Manuals Search And Download.
Labelling a tape
CLEAR
Before you start…
• Turn on your TV and set it to the video
channel.
1
4
7
2
5
8
0
3
6
9
MENU
M/m/</,
OK
Insert a SmartFile tape.
1
The SMARTFILE indicator lights up on the VCR.
Press MENU and select SMARTFILE EDIT,
SMARTFILE EDIT
PAGE 1
2 then press OK.
2 . 8 . 00 - 10 . 10. 00
10 . 10 SPORTS FESTIVAL
SPORTS
1 . 10 NEWS SEVEN
SP 1H 30M
CCB
SP 1H 30M
The SMARTFILE EDIT menu appears.
30 .
9
NICK & MATT
SHOW
SP 1H 30M
SELECT
CATEGORY
TITLE
:
:
:
EXIT : MENU
90 Labelling a recorded programme and tape
Download from Www.Somanuals.com. All Manuals Search And Download.
Press M to select the tape title.
SMARTFILE EDIT
3
4
5
PAGE 1
2 . 8 . 00 - 10 . 10. 00
10 . 10 SPORTS FESTIVAL
SPORTS
1 . 10 NEWS SEVEN
SP 1H 30M
CCB
SP 1H 30M
30 .
9
NICK & MATT
SHOW
SP 1H 30M
SELECT
TITLE EDIT
:
:
EXIT : MENU
Press ,.
SMARTFILE EDIT
PAGE 1
10 . 10 SPORTS FESTIVAL
The cursor moves to the title input position.
SPORTS
1 . 10 NEWS SEVEN
SP 1H 30M
CCB
SP 1H 30M
30 .
9
NICK & MATT
SHOW
SP 1H 30M
SELECT
BACK
CONFIRM
:
:
NEXT
:
: OK
EXIT : MENU
Label the tape.
SMARTFILE EDIT
M
10 . 10 SPORTS FESTIVAL
SPORTS CCB SP 1H 30M
1 . 10 NEWS SEVEN
PAGE 1
1 Press M/m to select a character.
Each time you press M, the character changes
as shown below.
SP 1H 30M
30 .
9
NICK & MATT
SHOW
SP 1H 30M
At Bt ... t Z t special characters t
! t& t, (comma) t - (hyphen) t .
(period) t 0 t 1 ... t9 t(blank space)
SELECT
BACK
CONFIRM
:
:
NEXT
:
: OK
EXIT : MENU
You can also select a blank space by pressing CLEAR.
2 To set the next character, press ,.
SMARTFILE EDIT
M
10 . 10 SPORTS FESTIVAL
SPORTS CCB SP 1H 30M
1 . 10 NEWS SEVEN
PAGE 1
The cursor moves to the next position.
SP 1H 30M
3 Repeat steps 1 and 2 to label the tape.
30 .
SHOW
9
NICK & MATT
SP 1H 30M
SELECT
BACK
CONFIRM
:
:
NEXT
:
: OK
EXIT : MENU
Press OK.
SMARTFILE EDIT
MY VIDEO TAPE
10 . 10 SPORTS FESTIVAL
SPORTS CCB SP 1H 30M
1 . 10 NEWS SEVEN
6 The tape title is stored.
PAGE 1
SP 1H 30M
30 .
9
NICK & MATT
SHOW
SP 1H 30M
SELECT
TITLE EDIT
:
:
EXIT : MENU
Press MENU to exit the menu.
7
To erase the tape title
Press CLEAR after step 3 above. The tape title is erased and the recording date
reappears. When you want to erase the recording date from the tape title column,
press CLEAR again.
Labelling a recorded programme and tape 91
Download from Www.Somanuals.com. All Manuals Search And Download.
Registering the contents of a recorded
tape in the SmartFile label
The VCR will register programmes
recorded on a tape (even a non-SmartFile
recorded tape) in the memory of a new
SmartFile label by detecting the index
signals indicating the start of recorded
g
programmes. You can register up to the 12th
programme from the start of the tape. The
programmes appear from the bottom of the
SMARTFILE GENERATOR
screen as PROGRAM NO. 1, PROGRAM
NO.2, ... PROGRAM NO.12 in this order.
The 13th and subsequent programmes are
ignored. You can manually name the
registered programme numbers and select
the category (see page 84).
Before you start…
• Turn on your TV and set it to the video channel.
• Turn on your VCR.
Attach the SmartFile label to the spine of the
1 cassette as shown on the right and insert the
tape.
SMARTFILE SENSOR
Press the SMARTFILE GENERATOR button on
2 . 8 . 00 - 10 . 10 . 00
PAGE 1
2 the VCR.
SMARTFILE INDEXING IS
IN PROGRESS
A message appears indicating that the recorded
programmes are being registered. The index
START
END
signals are detected from the start of the tape,
and the registration stops when the end of the
tape is reached. The message disappears when
registration is complete.
To stop registration to the SmartFile label
Press SMARTFILE GENERATOR.
The data registered before the button is pressed remains in the SmartFile label. You
can register the programmes again by pressing SMARTFILE GENERATOR again.
92 Registering the contents of a recorded tape in the SmartFile label
Download from Www.Somanuals.com. All Manuals Search And Download.
To check the information of a registered programme
Press SMARTFILE.
The SmartFile search list appears. The registered programme number, registration
date and recording time appear in this list. Note that the registration date differs from
the recorded date.
Registration date
PAGE 1
MY VIDEO TAPE
15 . 11 PROGRAM NO.11
SP 0H 30M
15 . 11 PROGRAM NO.10
LP 2H 00M
15 . 11 PROGRAM NO.
SP 0H 45M
SP 1H 55M
Programme located in
a recorded tape
Recording time
9
Estimated position of the
registered programme
START
END
SELECT
:
SEARCH : OK
EXIT : MENU
Tips
•
The programmes recorded on the tape can be registered again in a SmartFile label that
already contains programme data. However, the recorded date and time, programme name
and information input manually (such as the programme label and category) are replaced
with "PROGRAM NO. XX".
•
If the SmartFile label contains stored programme data that includes protected programmes, a
message appears and the registration stops.
Notes
•
Programme data is not registered correctly in the SmartFile label when :
– the programme length is about 20 minutes or less in LP mode or about 11 minutes in SP
mode.
– the programme does not have an index signal or the index signal has been recorded over and
erased.
– the tape is damaged or dirty.
•
•
If you don’t set the clock or the clock isn’t set to the correct date, the registration date won’t
be stored correctly on the SmartFile list.
After you press SMARTFILE GENERATOR and start registration, registration is interrupted
if you press x STOP, H PLAY, M FF, m REW, ?/1 or ./> INDEX SEARCH.
In these cases as well, the data registered up to the point when registration was interrupted
remains in the SmartFile label.
•
•
When you set AUTO LONG PLAY to ON in the TAPE OPTIONS menu, and the tape speed
automatically changes from SP to LP during recording, the VCR displays the entire recording
time converted to SP mode in the SmartFile list.
The estimated position of the registered programmes may not be correct if many short
programmes are recorded on long tapes.
Registering the contents of a recorded tape in the SmartFile label 93
Download from Www.Somanuals.com. All Manuals Search And Download.
Protecting a recorded programme
You can protect a recorded programme from
accidental over-recording or erasure using
the SmartFile function.
When you start recording from a position
prior to the protected programme, the
recording stops automatically before the
protected programme.
SMARTFILE
Before you start…
M/m/</,
• Turn on your TV and set it to the video
channel.
Insert a SmartFile tape.
MY VIDEO TAPE
BLANK TIME
10 . 10 SPORTS FESTIVAL
SPORTS CCB
1 . 10 NEWS SEVEN
PAGE 1
1
SP 1H 55M
The SMARTFILE indicator lights up on the
VCR.
SP 1H 30M
SP 0H 30M
30 .
9
NICK & MATT
SHOW
SP 1H 30M
START
SELECT
END
:
SEARCH : OK
EXIT : MENU
Press SMARTFILE.
2 The SmartFile search list appears on the TV screen.
Press M/m to select the programme you want to
MY VIDEO TAPE
BLANK TIME
10 . 10 SPORTS FESTIVAL
SPORTS CCB SP 1H 30M
1 . 10 NEWS SEVEN
PAGE 1
SP 1H 55M
3 protect.
SP 0H 30M
30 .
9
NICK & MATT
SHOW
SP 1H 30M
START
SELECT
END
:
SEARCH : OK
EXIT : MENU
94 Protecting a recorded programme
Download from Www.Somanuals.com. All Manuals Search And Download.
Press ,.
MY VIDEO TAPE
BLANK TIME
10 . 10 SPORTS FESTIVAL
SPORTS CCB SP 1H 30M
1 . 10 NEWS SEVEN
SP 0H 30M
PAGE 1
SP 1H 55M
4 The
indicator appears to the left of the
selected programme and the programme is now
protected.
30 .
9
NICK & MATT
SHOW
SP 1H 30M
END
START
SELECT
:
SEARCH : OK
EXIT : MENU
Press SMARTFILE.
5
The SmartFile search list disappears.
To unlock the protected programme
Press < in step 4 above. The
indicator disappears and you can record over this
programme.
Tips
•
When you start recording from a position prior to the protected programme, the recording
automatically stops no more than about four minutes in SP mode and about eight minutes in
LP mode before the beginning of the protected programme. The BLANK TIME indicator
flashes in the display window.
•
•
If you protect a programme just after the Blank Time space, BLANK TIME is shortened by
about four minutes in SP mode and about eight minutes in LP mode.
If you try to record on a SmartFile tape containing a protected programme, a message
indicating that there is a protected programme on this tape appears on the TV screen.
Notes
•
•
When you record another programme just after a protected programme, locate the beginning
of the Blank Time space by following the instructions in “Recording after locating the Blank
Time space“ on page 79. Otherwise, if the recording start point overlaps the protected
programme, the VCR may over-record the protected programme.
If you insert a SmartFile tape which contains a protected programme or protect a programme
for the first time on a new tape, the VCR will analyse the position of the protected
programme for a few seconds. You cannot operate the VCR while the VCR is analysing the
tape.
•
•
•
If the SmartFile list contains 12 protected programmes, the next programme you record won’t
be stored in the SmartFile list.
When you try to turn off the VCR after setting a ShowView or timer recording on the
protected programme, the VCR automatically ejects the cassette.
The protect function may not work with an NTSC-recorded tape.
Protecting a recorded programme 95
Download from Www.Somanuals.com. All Manuals Search And Download.
Erasing the data of an unwanted
programme
You can erase an unwanted programme
from the SmartFile list.
When you erase a programme from the list,
that portion of tape becomes Blank Time
space.
DISPLAY
CLEAR
1
4
7
2
5
8
0
3
6
9
Before you start…
• Turn on your TV and set it to the video
channel.
SMARTFILE
M/m/</,
Insert a SmartFile tape.
MY VIDEO TAPE
BLANK TIME
10 . 10 SPORTS FESTIVAL
SPORTS CCB SP 1H 30M
1 . 10 NEWS SEVEN
SP 0H 30M
PAGE 1
SP 1H 55M
1
The SMARTFILE indicator lights up on the
VCR.
30 .
9
NICK & MATT
SHOW
SP 1H 30M
END
START
SELECT
:
SEARCH : OK
EXIT : MENU
Press SMARTFILE.
2 The SmartFile search list appears on the TV screen.
96 Erasing the data of an unwanted programme
Download from Www.Somanuals.com. All Manuals Search And Download.
Press M/m to select a programme you want to
MY VIDEO TAPE
BLANK TIME
10 . 10 SPORTS FESTIVAL
SPORTS CCB SP 1H 30M
1 . 10 NEWS SEVEN
SP 0H 30M
PAGE 1
SP 1H 55M
3 erase from the list.
30 .
SHOW
9
NICK & MATT
SP 1H 30M
END
START
SELECT
:
SEARCH : OK
EXIT : MENU
Press CLEAR.
MY VIDEO TAPE
BLANK TIME
PAGE 1
4
SP 1H 55M
The selected programme is erased from the
SmartFile list.
SPORTS
30 .
SHOW
CCB
NICK & MATT
SP 1H 30M
9
SP 1H 30M
If you erase a programme by mistake, press
DISPLAY to make the programme reappear.
START
SELECT
END
:
SEARCH : OK
EXIT : MENU
Press SMARTFILE.
5
The SmartFile search list disappears.
Notes
•
You cannot erase a protected programme from the SmartFile list. You have to first unlock the
protected programme by following the instructions in “To unlock the protected programme“
on page 95, then erase that programme from the list.
•
•
The erased programme disappears from the SmartFile list, but it still remains on the tape.
If the remaining lenth of a program is about 11 minutes or less in SP mode or about 20
minutes or less in LP mode, you cannot make the programme reappear by using the
DISPLAY button.
Erasing the data of an unwanted programme 97
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
Troubleshooting
If you have any questions or if your problems are not covered below, please consult your nearest
Sony service facility.
Problem summary
The following table summarizes the reference numbers for the problems you might face. In
order to solve your problem, please refer to the corresponding reference (S1=symptom1,
S2=symptom2 ...) in the right column below.
CATEGORY
Picture
REFER TO
•
•
•
while watching broadcast tuned by the TV
while watching broadcast tuned by the VCR.
while playing a tape.
S2, S6
S1, S6
S3, S4, S5
Sound
•
while playing a tape.
S7, S8, S9
Functional
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Playback
S4, S9, S10
S11, S12
S13, S14
S15, S16
S17, S18, S19
S20, S21, S22
S23
Normal recording
SmartFile
Timer recording
Synchronized Recording
Canal Plus
Line selection
Remote commander
Cleaning
S24, S25
S26
Clock
S27
Power
S28, S29, S30, S31, S32
S33, S34
S35
Tape
SMARTLINK
Set-Top Box
S36
98 Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture
S1
The VCR picture
does not appear on
the TV screen.
t
t
Make sure the TV is set to the video channel. If you are using a
monitor, set it to video input.
If the VCR is connected to the TV with a Scart cable, make sure the
VIDEO key on the remote commander to lit the TV/VIDEO
indicator.
t
t
If your VCR is connected to the TV with only anaerial cable, make
sure the TV is correctly tuned to the VCR (see page 12).
S2
S3
The TV programme
is not clear or has
some interference.
If your TV is connected to the VCR with a Scart and an aerial
cables, make sure the RF MODULATOR is set to OFF (see page
18).
If your VCR is connected to the TV with only an aerial cable, make
sure the TV is correctly tuned to the VCR (see page 12).
t
t
The playback picture
is not clear or has
some interference.
If your TV is connected to the VCR with a Scart and an aerial
cables, make sure the RF MODULATOR is set to OFF (see page
18).
t
Existing broadcasts may interfere with the VCR. Reset the RF
MODULATOR output of your VCR (see page 18).
t
t
Adjust the tracking with the TRACKING +/– buttons (see page 66).
The video heads are dirty (see below). Clean the video heads using
the Sony T-25CLD, E-25CLDR, or T-25CLW video head cleaning
cassette. If these cleaning cassettes are not available in your area,
have the heads cleaned at your nearest Sony service facility (a
standard service charge will be required). Do not use a
commercially available liquid type cleaning cassette other than
Sony’s, as it may damage the video heads.
t
t
The video heads may have to be replaced. Consult your local Sony
service facility for more information.
S4
The tracking meter
does not appear on
the TV screen.
The recording condition of the tape is very poor and tracking
cannot be ajusted.
Symptoms caused by contaminated video heads
• Normal picture
• Rough picture
Unclear picture
• No picture (or
black & white
screen appears)
initial
terminal
contamination
continued
Download from Www.Somanuals.com. All Manuals Search And Download.
99
Picture
S5
S6
The picture rolls
vertically during
picture search.
t
Adjust the vertical hold control on the TV or monitor.
TV reception is poor.
t
t
t
Make sure the aerial cables are connected securely.
Adjust the TV aerial.
Make sure SYSTEM (B/G or D/K) in the TUNER menu is set to
the system in your area.
Sound
S7
The picture has no
sound.
t
t
The tape is defective. Please use a new tape.
Make sure SYSTEM (B/G or D/K) in the TUNER menu is set to
the system in your area.
S8
S9
The sound is
unstable or has an
echo.
t
When you play a tape with the same sound recorded on both the hi-
fi and normal sound tracks, make sure AUDIO MIX in the AUDIO
OPTIONS menu is set to OFF (see page 69).
You cannot select the
left or the right
channel while
t
t
Make sure AUDIO MIX is set to OFF in the AUDIO OPTIONS
menu (see page 69).
Make sure you are playing a hi-fi tape.
playing a tape
Playback
S10 The tape starts
playing as soon as it
t
t
This is normal. When you insert a tape with no safety tab, the VCR
starts playing automatically.
is inserted.
Normal recording
S11 The tape is ejected
when you press z
REC.
The safety tab has been removed. To record on this tape, cover the
tab hole (see page 46).
S12 Nothing happens
when you press z
REC.
t
t
Make sure the tape is not at its end.
If the BL indicator is flashing in the display window, the tape
page 94).
SmartFile
S13 The programmelabel
cannot be taken
t
t
Make sure the clock and the date are set correctly.
Check the setting of the TV guide pages. Some stations may not
offer this service (see page 84).
properly.
t
If you start recording more than two minutes before the beginning
of the programme, the title on the label may not correspond to the
one of the recorded programme. Manually enter the correct title
using the SMARTFILE EDIT menu (see page 87).
t
t
If the TV reception is poor, the VCR will not be able to take the title
correctly. Manually enter the correct title using the SMARTFILE
EDIT menu (see page 87).
S14 Recording stops
If the tape contains a programme protected by the SmartFile
function, recording automatically stops before the protected
programme. Use another tape which has enough recording space.
halfway.
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Timer recording
S15 The timer does not
t
t
Check that the clock is set.
The clock stops if the VCR is disconnected from the mains for
more than an hour. Reset the clock and the timer.
operate properly.
t
t
Check that the safety tab has not been removed.
If the timer recording overlaps a programme protected by the
SmartFile function, the recording stops halfway (see page 94).
t
t
t
t
t
The starting point of the recording overlaps a protected programme.
Make sure the tape is not at its end.
Make sure a tape has been inserted.
Make sure the current time is not already past your timer settings .
If you are recording a programme from a Set-Top Box, make sure
the Set-Top Box is turned on.
S16 The VPS/PDC
function does not
operate properly.
t
t
Check that the clock and the date are set correctly.
Check that the VPS/PDC time you set is the correct one (there
might be a mistake in the TV guide programme). If the broadcast
you wanted to record did not send the correct VPS/PDC
information, the VCR will not start recording.
t
t
If the reception is poor, the VPS/PDC signal might be altered and
the VCR might not start recording.
Synchronized
Recording
S17 The SYNCHRO
REC indicator turns
off while recording
or does not go back
to recording standby
mode.
The tape has reached its end. Insert a new tape and press
SYNCHRO REC again.
S18 The Synchronized
Recording function
does not work.
t
The connected equipment was not turned off.
Turn off the connected equipment and press SYNCHRO REC
again.
t
t
There was a power failure. Press SYNCHRO REC again.
S19 The programme
recorded with the
Synchronized
If the settings for timer recordings and Synchronized Recording
overlap, the programme that starts first has priority and the second
programme starts recording only after the first programme has
finished.
Recording function
is incomplete.
t
t
There was a power failure. Press SYNCHRO REC again.
Canal Plus
S20 You cannot set
channels as PAY-TV/
CANAL+ in the
Be sure that DECODER/LINE3 is set to DECODER in the OTHER
OPTIONS menu (see page 70).
TUNER menu.
S21 You cannot watch
Canal Plus when the
VCR is in standby
mode.
t
t
Be sure that DECODER/LINE3 is set to DECODER in the
OTHER OPTIONS menu (see page 70).
Make sure the Canal Plus Scart cable is plugged in securely.
continued
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Canal Plus
S22 PAY-TV/Canal Plus
is always recorded
scrambled.
t
t
Make sure the Canal Plus Scart cable is plugged in securely.
Be sure that DECODER/LINE3 is set to DECODER in the OTHER
OPTIONS menu (see page 70).
t
Be sure that this channel is set as PAY-TV/CANAL+ in the TUNER
menu (see page 36).
Line selection
S23 You cannot select
t
Be sure that DECODER/LINE3 is set to LINE3 in the OTHER
OPTIONS menu (see page 70).
LINE3.
Remote
commander
S24 The remote
commander does not
operate.
t
t
Make sure you are pointing the remote commander at the remote
sensor on the VCR.
Replace all of the batteries in the remote commander with new ones
if they are weak.
t
t
Make sure the TV/VIDEO remote control switch is set correctly.
S25 You cannot control
Set your TV’s code number. The code number may change when
your TV.
you replace the batteries for the remote commander (see page 8).
Cleaning
S26 The VCR needs to be
t
t
Clean the cabinet, panel and controls with a dry, soft cloth, or a soft
cloth slightly moistened with a mild detergent solution. Do not use
any type of solvent, such as alcohol or benzene.
cleaned.
Clock
S27 The clock has
stopped and “–:– –”
lights up in the
The clock stops if the VCR is disconnected from the mains for
more than one hour. Reset the clock and timer if needed (see page
21).
display window.
Power
S28 The ?/1 ON/
STANDBY switch
does not function.
t
t
t
Connect the mains lead to the mains securely.
S29 The power is turned
on but the VCR does
not operate.
Moisture condensation has occurred. Turn the power off, unplug
the mains lead and leave the VCR to dry for over three hours.
S30 The tape is ejected
when you press ?/1
ON/STANDBY.
You have set a timer recording, but the tape on which you want to
record is protected (or contains protected recordings). Unlock the
protection or use another tape or replace the safety tab (see page
95).
S31 The display does not
lit when the VCR is
in standby mode.
t
t
The VCR is in power save mode. Set the POWER SAVE option to
OFF in the OTHER OPTIONS menu (see page 70).
S32 POWER SAVE is set
to ON but the display
remains lit in standby
mode.
The display is always lit if the VCR is in timer standby mode. For
more details regarding the energy saving function, see page 70.
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Tape
S33 The tape is ejected
when you press ?/1
ON/STANDBY.
t
t
You have set a timer recording, but the tape on which you want to
record is protected (or contains protected recordings). Unlock the
protection or use another tape or replace the safety tab (see page
95).
S34 A tape cannot be
inserted.
SMARTLINK
S35 The SMARTLINK
function does not
t
t
t
Check that your TV complies with SMARTLINK, NexTView Link,
MEGALOGIC, EASYLINK/CinemaLink, Q-Link or TV-LINK.
Make sure you use the Scart cable, supplied with the VCR, to
connect the VCR and your TV.
Make sure the Scart cable is connected securely. Refer to your TV
manual for instructions.
work properly.
Set-Top Box
S36 You cannot watch the
satellite tuner picture
when the VCR is in
standby mode or z
t
t
Be sure that the DECODER/LINE-3 is set to LINE3- in the
OTHER OPTIONS menu (see page 70).
Make sure the POWER SAVE option is set to OFF in the OTHER
OPTIONS menu (see page 70).
REC standby mode.
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Input signal: 1 Vp-p, 75 ohms, unbalanced, sync
negative
System
Channel coverage
AUDIO IN, phono jack (2)
Input level: 327 mVrms
PAL (D/K, B/G)
VHF E2 to E12, R1-R12
VHF Italian channel A to H
UHF E21 to E69, R21-R69
CATV S01 to S05, S1 to S41
RF output signal
Input impedance : more than 47 kilohms
LINE-2 OUT
VIDEO OUT, phono jack (1)
Output signal: 1 Vp-p, 75 ohms, unbalanced, sync
negative
UHF channels 21 to 69
Aerial out
75-ohm asymmetrical aerial socket
Tape speed
AUDIO OUT, phono jack (2)
Rated output level: 327 mVrms
Load impedance: 47 kilohms
Output impedance: less than 10 kilohms
SP: PAL/MESECAM 23.39 mm/s (recording/
playback)
NTSC33.35 mm/s (playback only)
General
Power requirements
220 – 240 V AC, 50 Hz
LP: PAL/MESECAM 11.70 mm/s (recording/
playback)
Power consumption
NTSC16.67 mm/s (playback only)
EP:NTSC11.12 mm/s (playback only)
Maximum recording/playback time
10 hrs. in LP mode (with E300 tape)
Fast-forward and rewind time
25 W (Normal)
2,7 W (POWER SAVE is set to ON, no decoder)
Operating temperature
5°C to 40°C
Storage temperature
Approx. 1 min. (with E180 tape)
–20°C to 60°C
Dimensions
Inputs and outputs
Approx. 430 × 100 × 330 mm (w/h/d)
including projecting parts and controls
Mass
iLINE-1 (TV)
21-pin
Video input: pin 20
Audio input: pins 2 and 6
Video output: pin 19
Audio output: pins 1 and 3
DECODER/t LINE-3 IN
21-pin
Video input: pin 20
Audio input: pins 2 and 6
LINE-2 IN
Approx. 4.8 kg
Supplied accessories
Remote commander (1)
R6 (size AA) batteries (2)
Aerial cable (1)
SmartFile labels (10)
Design and specifications are subject to change without
notice.
VIDEO IN, phono jack (1)
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Index to parts and controls
Refer to the pages indicated in parentheses ( ) for details.
Front panel
g
A ?/1 (on/standby) button/indicator (6)
B SMARTFILE button (75)
C SMARTFILE sensor (82)
D CURSOR M/m buttons (82)
E Tape compartment
M z (record) button (44),(73)
N AUTO SET UP (19)/
RF (Radio Frequency) CHANNEL
button(16)
O M (fast-forward)
m (rewind) buttons (42)
F REALITY REGENERATOR (RR)
(16), (19), (66)
indicator (66)
Q REALITY REGENERATOR button (66)
R SMARTFILE indicator (82)
S Remote sensor (5)
G SYNCHRO REC indicator (60)
H Z (eject) button (42)
I SYNCHRO REC button (60)
J H (playback) button (42)
K x (stop) button (42)
T OK button
U SMARTFILE GENERATOR button
V LINE-2 IN VIDEO/AUDIO L/R jacks
L X (pause) button (42)
(71)
continued
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Display window
SMARTLINK SPEP
OPC
LP
STEREO
TV NICAM
VIDEO
VPS
PDC
BL
EDIT
H
M
S
A Timer indicator (48), (53)
H STEREO indicator (63)
(Programme Delivery Control) indicator
(51)
I NICAM indicator (63)
J Time counter/clock/line/programme
position indicator (16), (42), (45)
C OPC (Optimum Picture Control)
K Remaining time indicator (46)
L Tracking indicator (66)
indicator (66)
D SMARTLINK indicator (11)
E Tape speed indicators (45)
F VIDEO indicator (45)
G TV indicator (47)
M EDIT indicator (73)
N BL (Blank Time space) indicator (82)
O Tape/recording indicator (45)
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear panel
A Mains lead (9), (12)
E AERIAL OUT
ANTENNE SORTIE connector (9), (12)
B i LINE-1 (TV)
i LIGNE-1 (TV) connector (9), (36)
F NTSC PB (Play Back) switch (41)
C DECODER/t LINE-3 IN
DECODEUR/t ENTREE LIGNE-3
connector (36)
G LINE-2 OUT
AUDIO L(left)/R (right)/VIDEO
SORTIE LIGNE-2
AUDIO G/D/VIDEO (15)
D AERIAL IN
ANTENNE ENTREE connector (9), (12)
continued
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote commander
A Z EJECT button (42)
B WIDE button (for TV) (7)
C AUDIO MONITOR button (6), (63)
D X2 button*
E y SLOW button*
F SP (Standard Play)/LP (Long Play)
button (44)
G
DISPLAY button (46)
H –/– –(ten’s digit) button (6), (46)
I 2 (volume) +/– buttons (for TV) (6)
J z REC (record) button (44), (58), (73)
K MENU button
1
4
7
2
5
8
0
3
6
9
L M/m/</, buttons
OK button
m
REW(rewind) button (42), (56)
M
FF (fast-forward) button (42),
(56)
H PLAY button (42), (56)
x STOP button (42), (58)
X PAUSE button (42), (58)
*
FASTEXT buttons (for TV)
108
Download from Www.Somanuals.com. All Manuals Search And Download.
M TV/VIDEO remote control switch (5)
N ?/1 (on/standby) button (6), (53)
O COUNTER/REMAIN button* (46)
/ (Teletext) button (for TV) (6)
P a TV power on/TV mode select button
(for TV) (6)
Q ./> INDEX SEARCH buttons*
(65)
R CLEAR button (41), (48), (61)
S t TV/VIDEO button (6)
T Programme number buttons (6)
U INPUT SELECT button (45), (53)
1
4
7
2
5
8
0
3
6
9
V PROG (programme) +/– buttons (6),
(26) (45)
c/C Teletext page access buttons (for
TV) (7)
W
TIMER button (48), (53)
X SMARTFILE button (77)
*
FASTEXT buttons (for TV)
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu chart
This VCR is equipped with an on-screen indication system which allows you a visual, quick and easy
selection of the different menus. For a total view of all the menus, please refer to the following chart.
TIMER
2 8 . 9 THU
DATE
TODAY
TIME
2 0 : 0 0 2 1 : 0 0
PROG.
AAB
SP / LP
LIST
SP
VPS / PDC
OFF
CHANNEL LIST
SELECT
:
:
:
PROG
CH
NAME
AAB
CDE
LMO
SET
1
2
3
4
5
C
C
C
C
C
1 2
0 3
5 6
2 7
0 9
CANCEL
CLEAR
OPTIONS
TIMER
EXIT : MENU
FGH
LISTS
OPTIONS
LISTS
SELECT
MOVE PROGRAM
ERASE PROGRAM
:
:
:
SMARTFILE EDIT
SETTINGS
CLEAR
CHANNEL LIST
TIMER LIST
RETURN
EXIT : MENU
SELECT
SET
:
TIMER LIST
: OK
2 8 . 9 THU
EXIT : MENU
VPS
PDC
DATE
TIME
PROG.
TODAY
2 0 : 0 0 2 1 : 0 0
1 4 : 0 0 1 5 : 0 0
2 0 : 0 0 2 1 : 0 0
AAB
FGH
AAB
I J K
CDE
– –
SP
LP
SP
LP
LP
–
MON
3 0 . 9
SUN
–
FRI
SELECT
SET
:
6 : 3 0
7 : 0 0
VPS
PDC
: OK
2 . 1 0
1 0 : 0 0 1 1 : 3 0
EXIT : MENU
– – . – –
– – . – –
– – . – –
RETURN
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– –
–
– –
–
SELECT
SET
CANCEL
:
: OK
OPTIONS
:
CLEAR
EXIT : MENU
VIDEO OPTIONS
AUDIO OPTIONS
TAPE OPTIONS
OTHER OPTIONS
RETURN
SELECT
SET
:
: OK
EXIT : MENU
SMARTFILE EDIT
MY VIDEO TAPE
PAGE 1
10 . 10 SPORTS FESTIVAL
SPORTS CCB SP 1H 30M
1 . 10 NEWS SEVEN
SP 1H 30M
30 .
9
NICK & MATT
SHOW
SP 1H 30M
SELECT
TITLE EDIT
:
:
EXIT : MENU
SETTINGS
TUNER
CLOCK
LANGUAGE
TV GUIDE PAGE
RETURN
SELECT
SET
:
: OK
EXIT : MENU
110 Menu chart
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO OPTIONS
OPC
EDIT
ON
OFF
SHARPNESS
COLOUR SYSTEM
RR
NORMAL
AUTO
NORMAL
RETURN
SELECT
SET
:
: OK
EXIT : MENU
AUDIO OPTIONS
AUDIO MIX
HIFI AUDIO
RETURN
OFF
NICAM
SELECT
SET
:
: OK
EXIT : MENU
TAPE OPTIONS
AUTO LONG PLAY
TAPE LENGTH
RETURN
OFF
E180
TUNER
SYSTEM
NORMAL / CATV
CHANNEL SET
PAY - TV / CANAL+
AFT
PROG.
1
D/K
NORMAL
1 2 AAB
C
OFF
ON
SELECT
SET
:
: OK
FINE TUNING
RETURN
EXIT : MENU
OTHER OPTIONS
SELECT
SET
:
BUZZER
ON
: OK
DIMMER
OFF
EXIT : MENU
DECODER/LINE3
POWER SAVE
TIMER OPTIONS
TV DIRECT REC
RETURN
DECODER
OFF
VARIABLE
ON
CLOCK
AUTO ADJUST
CLOCK PROGRAM
MANUAL ADJUST
2 8 . 9 . 2 0 0 0
1
AAB
1 8 : 0 0
SELECT
SET
:
THU
: OK
EXIT : MENU
SELECT
:
CONFIRM : OK
EXIT : MENU
LANGUAGE
ENGLISH
POLSKI
ČESKÝ
MAGYAR
SLOVENČINA
TÜRKÇE
РУССКИЙ
SELECT
SET
:
: OK
EXIT : MENU
PROG . 5
TV GUIDE PAGE
SUN
MON
TUE
WED
THU
FRI
P 3 0 1
P - - -
P - - -
P - - -
P - - -
P - - -
P - - -
SAT
SELECT
SET
:
: OK
EXIT : MENU
Menu chart 111
Download from Www.Somanuals.com. All Manuals Search And Download.
112
Download from Www.Somanuals.com. All Manuals Search And Download.
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
erasing the data of an unwanted
programme 96
labelling a recorded programme
protecting a recorded programme
94
registering the contents of a recor-
ded tape in the SmartFile label 92
A
M
Accesories supplied 4
Adjusting
Monitoring
during playback 64
picture 29, 66
tracking 66
AFT (Auto Fine Tuning) 29
Audio track 64
Auto Clock set 23
Auto Set Up 19
N
Normal audio track 64
SMARTLINK 11
One Touch Menu 11
One Touch Play 11, 43
One Touch Timer 11
C
O
Canal Plus 36
Changing the programme posi-
tion 32
Clock setting 21
Color system
OPC (Optimum Picture Con-
P
PAY-TV 36
PDC (Programme Delivery
Control) 51
Picture adjustment. See Adjus-
ting
compatible colour systems 2
setting 42
Connecting
to a decoder 36
Station name
changing 30
Synchronized Recording 59
to a Set-Top Box 13, 14
Playback 41
to a stereo system 15
Power save 70
to the TV with
a
EURO-AV
(Scart) connector 9
to the TV with an aerial cable only
12
T
Counter 42
overlapping timer recording 62
using the ShowView system 48
Timer setting
cancelling 61
changing 61
Presetting channels 26
D
R
Disabling the programme posi-
tions 34
Dubbing. see Editing
Recording 44
saving 46
using the ShowView system 48
what you are watching on the TV
47
Tracking adjustment. See Ad-
E
Editing 71
EP mode 43
while watching another program-
me 46
EURO-AV connection 9
Remote commander 5
RF channel 16, 18
V
VPS (Video Programme Sys-
tem) 51
H
RR (Reality Regenerator) 66
Hi-fi audio track 64
S
Z
I
Safety tab 46
Searching
at various speeds 56
using the index function 65
Set-Top Box
Zweiton broadcasts 63
Index Search 65
L
Language selecting 25
LP mode 45
connecting 13, 14
line through 13
SMARTFILE
checking the contents of a tape 82
Sony Corporation Printed in France
Download from Www.Somanuals.com. All Manuals Search And Download.
|