3-081-622-12 (1) GB
Video Cassette
Recorder
Operating Instructions
PAL
SLV-SE830G
SLV-SE730G/I
SLV-SE230G/I
© 2003 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Do not place heavy objects on the unit.
WARNING
To prevent fire or shock hazard, do not expose the
unit to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
If the unit is brought directly from a cold to a
warm location, moisture may condense inside the
VCR and cause damage to the video head and
tape. When you first install the unit, or when you
move it from a cold to a warm location, wait for
about three hours before operating the unit.
Mains lead must only be changed at a qualified
service shop.
Notice for customers in the United
Kingdom and Republic of Ireland
A moulded plug complying with BS1363 is fitted to
this equipment for your safety and convenience.
Should the fuse in the plug supplied need to be
replaced, a 5 AMP fuse approved by ASTA or BSI
Caution
Television programmes, films, video tapes and other
materials may be copyrighted. Unauthorized
recording of such material may be contrary to the
provisions of the copyright laws. Also, use of this
recorder with cable television transmission may
require authorization from the cable television
transmitter and/or programme owner.
to BS1362, (i.e., marked with
be used.
or
mark) must
Compatible colour systems
This VCR is designed to record and play back using
the PAL colour system. Recording of video sources
based on other colour systems cannot be guaranteed.
If the plug supplied with this equipment has a
detachable fuse cover, be sure to attach the fuse
cover after you change the fuse. Never use the plug
without the fuse cover. If you should lose the fuse
cover, please contact your nearest Sony service
station.
VIDEO Plus+ and PlusCode are registered
trademarks of Gemstar Development Corporation.
The VIDEO Plus+ system is manufactured under
license from Gemstar Development Corporation.
Precautions
Safety
•
•
•
•
This unit operates on 220 – 240 V AC, 50 Hz.
Check that the unit’s operating voltage is
identical with your local power supply.
If anything falls into the cabinet, unplug the unit
and have it checked by qualified personnel before
operating it any further.
The unit is not disconnected from the mains as
long as it is connected to the mains, even if the
unit itself has been turned off.
Unplug the unit from the wall outlet if you do not
intend to use it for an extended period of time. To
disconnect the cord, pull it out by the plug, never
by the cord.
•
To prevent fire or shock hazard, do not place
objects filled with liquids, such as vases, on the
apparatus.
Installing
•
•
•
Do not install this equipment in a confined space
such as a book or similar unit.
Allow adequate air circulation to prevent internal
heat buildup.
Do not place the unit on surfaces (rugs, blankets,
etc.) or near materials (curtains, draperies) that
may block the ventilation slots.
•
Do not install the unit near heat sources such as
radiators or air ducts, or in a place subject to
direct sunlight, excessive dust, mechanical
vibration or shock.
•
•
Do not install the unit in an inclined position. It is
designed to be operated in a horizontal position
only.
Keep the unit and cassettes away from equipment
with strong magnets, such as microwave ovens or
large loudspeakers.
WARNING
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
52 Playing/searching at various speeds
54 Setting the recording duration time
55 Checking/changing/cancelling
timer settings
57 Recording stereo and bilingual
programmes (not available on SLV-
SE230G/I)
59 Searching using the index function
(not available on SLV-SE230G/I)
61 Adjusting the picture
4 Index to parts and controls
11 Step 1 : Unpacking
12 Step 2 : Setting up the remote
commander
16 Step 3 : Connecting the VCR
20 Step 4 : Setting up the VCR with
the Auto Set Up function
22 Downloading the TV tuner’s preset
data (not available on SLV-SE230G/I
23 Selecting a language
24 Presetting channels
27 Changing/disabling programme
positions
)
62 Reducing the VCR’s power
consumption
63 Changing menu options
32 Setting the clock
65 Connecting to a VCR or stereo
system
34 Playing a tape
67 Basic editing
36 Recording TV programmes
40 Recording TV programmes using
the Dial Timer (SLV-SE830G only)
45 Recording TV programmes using
the VIDEO Plus+® system
69 Troubleshooting
73 Specifications
74 Index
49 Setting the timer manually
Back Cover
Quick Start Guide
Table of contents
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Index to parts and controls
Refer to the pages indicated in parentheses ( ) for details.
Front panel
For SLV-SE830G
A ?/1 (on/standby) switch
C Tape compartment
N
DIAL TIMER (40)
P t LINE-2 L (left) o R (right)
How to open the jack cover
1 Press the bottom of the cover.
2 Hook your finger on the top edge of the
cover and pull it open.
* The H (play), x (stop) and
PROGRAM + buttons and jack cover
have a tactile dot.
Index to parts and controls
4
Download from Www.Somanuals.com. All Manuals Search And Download.
For SLV-SE730G/I
A ?/1 (on/standby) switch
C Tape compartment
* The H (play), x (stop) and
PROGRAM + buttons have a tactile dot.
continued
Index to parts and controls
5
Download from Www.Somanuals.com. All Manuals Search And Download.
For SLV-SE230G/I
A ?/1 (on/standby) switch
D Tape compartment
* The H (play), x (stop) and
PROGRAM + buttons have a tactile dot.
Index to parts and controls
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Display window
For SLV-SE830G and SE730G/I
1
2
3
4
5
8
A Tape indicator
7
6
C Time counter/clock/line/programme
position indicator (34) (36) (67)
D
(smartlink) indicator (18)
For SLV-SE230G/I
A Tape indicator
F Playback indicator
B Time counter/clock/line/programme
continued
Index to parts and controls
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear panel
For SLV-SE830G and SE730G/I
For SLV-SE230G/I
A
(in from antenna) connector (16)
B LINE-3 connector*1
F
*1 SLV-SE830G only
*2 SLV-SE730G/I and SE230G/I only
D AUDIO (OUT) R (right), L (left)
Index to parts and controls
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote commander
B
C
E Programme number buttons*1 (13)
G / (Teletext) button (for TV)*2 (14)
1
4
7
2
5
8
0
3
6
9
I a TV power on/TV mode select
button (for TV)*2 (13)
K SP (Standard Play)/LP (Long Play)
button (36)
*1 The H (play), AUDIO MONITOR,
number 5 and PROG + buttons have a
tactile dot.
*2 SLV-SE830G only
continued
Index to parts and controls
9
Download from Www.Somanuals.com. All Manuals Search And Download.
N [TV] / [VIDEO] remote control switch
P AUDIO MONITOR button*1*3 (14)
1
4
7
2
5
8
0
3
6
9
T PROG (programme) +/– buttons*1
c ⁄ CTeletext page access buttons
(for TV)*2 (14)
U y SLOW button*4 (52)
V ×2 button*4 (52)
W ./> (index search)
buttons*3*4 (59)
X
*1 The H (play), AUDIO MONITOR,
number 5 and PROG + buttons have a
tactile dot.
*2 SLV-SE830G only
*3 not available on SLV-SE230G/I
*4 FASTEXT buttons (for TV) (SLV-
SE830G only)
Index to parts and controls
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 1 : Unpacking
Check that you have received the following items with the VCR:
• Remote commander
• R6 (size AA) batteries
• Aerial cable
Check your model name
The instructions in this manual are for the 5 models: SLV-SE830G, SE730G,
SE730I, SE230G and SE230I. Check your model name by looking at the rear
panel of your VCR.
SLV-SE830G is the model used for illustration purposes. Any difference in
operation is clearly indicated in the text, for example, “SLV-SE830G only.”
Unpacking
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2 : Setting up the remote commander
Inserting the batteries
Insert two R6 (size AA) batteries
by matching the + and – on the
batteries to the diagram inside the
battery compartment.
Insert the negative (–) end first,
then push in and down until the
positive (+) end clicks into the
position.
Using the remote
Remote sensor
commander
You can use this remote
commander to operate this VCR
and a Sony TV. Buttons on the
remote commander marked with a
dot (•) can be used to operate your
Sony TV. If the TV does not have
the
symbol near the remote
[TV] /
[VIDEO]
sensor, this remote commander
will not operate the TV.
1
4
7
2
5
8
0
3
6
9
To operate
the VCR
Set [TV] / [VIDEO] to
[VIDEO] and point at the remote sensor at the VCR
a Sony TV
[TV] and point at the remote sensor at the TV
Setting up the remote commander
12
Download from Www.Somanuals.com. All Manuals Search And Download.
?/1
AUDIO MONITOR
DISPLAY
t TV/VIDEO
1
4
7
2
5
8
0
3
6
9
Programme
number
buttons
-
/
PROG +/–/
c ⁄ C
2 +/–
a
FASTEXT buttons
TV control buttons
To
Press
Set the TV to standby mode
?/1
Select an input source: aerial in or line in
Select the TV’s programme position
t TV/VIDEO
Programme number buttons,
-, PROG +/–
Adjust the volume of the TV
Switch to TV (Teletext off)*1
2 +/–
a (TV)
continued
Setting up the remote commander
13
Download from Www.Somanuals.com. All Manuals Search And Download.
To
Press
Switch to Teletext*1
Select the sound*2
Use FASTEXT*1
Call up the on-screen display
/ (Teletext)
AUDIO MONITOR
FASTEXT buttons
DISPLAY
Change the Teletext page*1
c ⁄ C
Switch to/from wide mode of a Sony wide TV (For
other manufactures’ wide TVs, see “Controlling
SE830G only)” below.)
(wide)
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove
the batteries to avoid possible damage from battery leakage.
• Do not use a new battery together with an old one.
• Do not use different types of batteries together.
• Some buttons may not work with certain Sony TVs.
*1 SLV-SE830G only
*2 not available on SLV-SE230G/I
Controlling other TVs with the remote commander (SLV-
SE830G only)
The remote commander is preprogrammed to control non-Sony TVs. If your
TV is listed in the following table, set the appropriate manufacturer’s code
number.
Set [TV] / [VIDEO] at the top of the remote commander to [TV].
1
Hold down ?/1, and enter your TV’s code number using the programme
2 number buttons. Then release ?/1.
Now you can use the following TV control buttons to control your TV:
?/1, t TV/VIDEO, programme number buttons, - (ten’s digit),
PROG +/–, 2 +/–, a (TV), / (Teletext), FASTEXT buttons,
(wide)*, MENU*, M/m/</,*, and OK*.
* These buttons may not work with all TVs.
Setting up the remote commander
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until
you find the one that works with your TV.
To switch to wide mode, see the footnotes below this table for the applicable
code numbers.
Manufacturer
Sony
Code number
Manufacturer
Panasonic
Philips
Code number
01*1, 02
17*1, 49
06*1, 07*1, 08*1
Akai
68
Ferguson
Grundig
Hitachi
JVC
52
Saba
12, 13
22, 23
25
10*1, 11*1
Samsung
Sanyo
24
33
Sharp
29
Loewe
Mivar
45
Telefunken
Thomson
Toshiba
36
43*2
38
09, 70
NEC
66
15, 16, 69*3
Nokia
*1 Press
*2 Press
*3 Press
(wide) to switch the wide picture mode on or off.
(wide), then press 2 +/– to select the wide picture mode you want.
(wide). The menu appears on the TV screen. Then, press M/m/</, to
select the wide picture you want and press OK.
Tip
• When you set your TV’s code number correctly while the TV is turned on, the TV
turns off automatically.
Notes
• If you enter a new code number, the code number previously entered will be
erased.
• If the TV uses a different remote control system from the one programmed to work
with the VCR, you cannot control your TV with the remote commander.
• When you replace the batteries of the remote commander, the code number may
change. Set the appropriate code number every time you replace the batteries.
Setting up the remote commander
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3 : Connecting the VCR
If your TV does not have a Scart (EURO-AV) connector
Mains lead
AERIAL IN
Aerial cable (supplied)
to mains
: Signal flow
Disconnect the aerial cable from your
1
2
TV and connect it to
panel of the VCR.
on the rear
Connect
of the VCR and the aerial
input of your TV using the supplied
aerial cable.
Connect the mains lead to the mains.
3
Note
• When you connect the VCR and your TV only with an aerial cable, you have to
Connecting the VCR
16
Download from Www.Somanuals.com. All Manuals Search And Download.
If your TV has a Scart (EURO-AV) connector
LINE-1 (EURO AV)
Mains lead
to mains
AERIAL IN
Aerial cable (supplied)
Scart
(EURO-AV)
Scart cable (not supplied)
: Signal flow
Disconnect the aerial cable from
1
2
3
your TV and connect it to
the rear panel of the VCR.
on
Connect
of the VCR and the
aerial input of your TV using the
supplied aerial cable.
Connect LINE-1 (EURO AV) on
the VCR and the Scart (EURO-
AV) connector on the TV with the
optional Scart cable.
This connection improves picture
and sound quality. Whenever you
want to watch the VCR picture,
press t TV/VIDEO to display
the VIDEO indicator in the
display window.
Connect the mains lead to the mains.
4
continued
Connecting the VCR
17
Download from Www.Somanuals.com. All Manuals Search And Download.
About the SMARTLINK features (not available on SLV-SE230G/I)
If the connected TV complies with
SMARTLINK, MEGALOGIC*1,
EASYLINK*2, Q-Link*3, EURO
VIEW LINK*4, or T-V LINK*5, this
VCR automatically runs the
SMARTLINK function after you complete the steps on the previous page
(the
indicator appears in the VCR’s display window when you turn on the
TV). You can enjoy the following SMARTLINK features.
• TV Direct Rec
You can easily record what you are watching on the TV when the VCR is
• One Touch Play
With One Touch Play, you can start playback automatically without
• One Touch Menu
When the VCR is turned on, you can turn on the TV, set the TV to the
video channel, and display the VCR’s on-screen display automatically by
pressing MENU on the remote commander.
• One Touch Timer
When the VCR is turned on, you can turn on the TV, set the TV to the
video channel, and display the timer recording menu (the TIMER
PROGRAMMING menu or the VIDEOPLUS menu) automatically by
pressing TIMER on the remote commander.
You can set which timer recording menu is displayed using TIMER
• NexTView Download
You can easily set the timer by using the NexTView Download function on
your TV. Please refer to your TV’s instruction manual.
*1 “MEGALOGIC” is a registered trademark of Grundig Corporation.
*2 “EASYLINK” is a trademark of Philips Corporation.
*3 “Q-Link” is a trademark of Panasonic Corporation.
*4 “EURO VIEW LINK” is a trademark of Toshiba Corporation.
*5 “T-V LINK” is a trademark of JVC Corporation.
Note
• Not all TVs respond to the functions above.
Connecting the VCR
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional connections
To a stereo system (not
available on SLV-
SE230G/I)
AUDIO R, L
You can improve sound
quality by connecting a
stereo system to the
AUDIO R, L jacks as shown
on the right.
LINE IN
Audio cable (not supplied)
: Signal flow
To a satellite or digital
tuner with Line Through
Using the Line Through
function, you can watch
programmes from a satellite
or digital tuner connected to
this VCR on the TV even
when the VCR is turned off.
When you turn on the
satellite or digital tuner, this
VCR automatically sends the
signal from the satellite or
digital tuner to the TV
LINE-3*1 or LINE-2*2
LINE
OUT
Scart cable (not supplied)
: Signal flow
without turning itself on.
Connect the satellite or digital tuner to the LINE-3*1 or LINE-2*2
1 connector as shown above.
Turn off the VCR.
2
To watch a programme, turn on the satellite or digital tuner and the TV.
Notes
• The Line Through function will not operate properly if POWER SAVE in the
USER SET menu is set to ECO2. Set POWER SAVE to OFF or ECO1 to ensure
• You cannot watch programmes on the TV while recording unless you are recording
a satellite or digital programme.
• This function may not work with some types of satellite or digital tuners.
• When the VCR is turned off, set the TV to the video channel.
*1 SLV-SE830G only
*2 SLV-SE730G/I and SE230G/I only
Connecting the VCR
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4 : Setting up the VCR with the Auto
Set Up function
Before using the VCR for the first time, set up the VCR using the Auto Set Up
function. With this function, you can set the TV channels, guide channels for the
VIDEO Plus+ system, and VCR clock automatically.
Turn on your TV and set it to the video channel.
1
If your TV does not have a Scart (EURO-AV) connector, tune the
TV to channel 21 (the initial RF channel for this VCR). Refer to
your TV’s manual for TV tuning instructions. If the picture does not
appear clearly, see “To change the RF channel” on page 20.
Connect the mains lead to the mains.
2
The VCR automatically turns on, and the message for the Auto Set
Up function appears.
Press OK.
3
The VCR starts searching for all of
the receivable channels and presets
AUTO SET UP
OK
PLEASE WAIT
them in the appropriate order for
4 0 %
your local area.
If you want to change the order of
the channels or disable unwanted
EXIT : MENU
programme positions, see
After the search or download is complete, the current time appears
for any stations that transmit a time signal. If the time does not
To cancel the Auto Set Up function
Press MENU.
To change the RF channel
If the picture does not appear clearly on the TV, change the RF channel on
the VCR and TV. Select INSTALLATION from the menu, then press M/m
to highlight VCR OUTPUT CH and press ,. Select the RF channel by
pressing the M/m buttons. Then, tune the TV to the new RF channel so that
a clear picture appears.
Setting up the VCR with the Auto Set Up function
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
• Whenever you operate the Auto Set Up function, some of the settings
(VIDEO Plus+, timer, etc.) will be reset. If this happens, you have to set them
again.
• Auto preset starts automatically only when you plug in the mains lead for the first
time after you purchase the VCR.
• If you want to use the Auto Set Up function again, press MENU, then press M/m/
</, to highlight INSTALLATION and press OK. Press M/m to highlight
AUTO SET UP, then repeat the procedure in step 3.
• Auto preset can be performed by pressing x (stop) on the VCR continuously for 5
seconds or more with no tape inserted.
Setting up the VCR with the Auto Set Up function
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Downloading the TV tuner’s preset data
(not available on SLV-SE230G/I)
You can download your TV tuner’s preset data to the VCR and tune the VCR
according to that data using the SMARTLINK connection.
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
Press MENU, then press M/m/</
MENU
1
, to highlight INSTALLATION
AUTO SET UP
and press OK.
MANUAL SET UP
SMARTLINK
VCR OUTPUT CH
: 2 1
OK
SELECT
END
:
SET
EXIT : MENU
:
: OK
Press M/m to highlight
2
3
SMARTLINK
SMARTLINK, then press ,.
TV CH DOWNLOAD
TV DIRECT RECORD : OFF
SELECT
END
:
SET
EXIT : MENU
:
: OK
Press M/m to highlight TV CH
DOWNLOAD, then press ,. The
Preset Download function starts and
TV CH DOWNLOAD
PLEASE WAIT
OK
the
indicator flashes in the
display window during download.
4 0 %
START:
EXIT : MENU
END
: OK
Downloading the TV tuner’s preset data (not available on SLV-SE230G/I)
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a language
If you prefer an on-screen language other than English, use the on-screen display to
select another language.
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
Press MENU, then press M/m/</
MENU
1
, to highlight LANGUAGE SET
GB
ES
NL
FI
DE
IT
SE
GR
FR
PT
DK
TR
and press OK.
OK
SELECT
SET
:
: OK
EXIT : MENU
Press M/m/</, to highlight the abbreviation of the desired
language from the table below, then press OK.
2
OK
The abbreviations of the languages are as follows:
Abbreviation Language Abbreviation Language
GB
ES
NL
FI
English
Spanish
Dutch
SE
GR
FR
PT
DK
TR
Swedish
Greek
French
Finnish
German
Italian
Portuguese
Danish
DE
IT
Turkish
Selecting a language
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Presetting channels
If some channels could not be preset using the Auto Set Up function, you can preset
them manually.
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
Press MENU, then press M/m/</
MENU
1
, to highlight INSTALLATION
AUTO SET UP
and press OK.
MANUAL SET UP
SMARTLINK
VCR OUTPUT CH
: 2 1
OK
SELECT
END
:
SET
EXIT : MENU
:
: OK
Press M/m to highlight MANUAL
2
3
TV STATION TABLE
SET UP, then press ,.
PR
1
2
3
4
CH
NAME
OK
0 2 7
0 2 9
0 3 0
0 3 2
A A B –
L MN–
CDE –
I
J K –
5
SWAPPING : OK
EXIT : MENU
DELETE : CLEAR
Press M/m to highlight the row
which you want to preset, then press
,.
To display other pages for
programme positions 6 to 80, press
M/m repeatedly.
MANUAL TUNING
PR
CH
MFT
NAME
:
:
:
:
5
OK
– – –
–
– – – –
SELECT
END
:
SET
EXIT : MENU
:
: OK
Presetting channels
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Press </, repeatedly until the
4
5
6
MANUAL TUNING
channel you want is displayed.
PR
CH
MFT
NAME
:
:
:
:
5
OK
OK
OK
0 3 3
–
– – – –
SELECT
END
:
SET
EXIT : MENU
:
: OK
Press M/m to highlight NAME, then
press ,.
MANUAL TUNING
PR
CH
MFT
NAME
:
:
:
:
5
0 3 3
–
– – – –
SELECT
END
:
SET
EXIT : MENU
:
: OK
Enter the station name.
MANUAL TUNING
1 Press M/m to select a character.
Each time you press M, the
character changes as shown
below.
PR
CH
MFT
NAME
:
:
:
:
5
0 3 3
–
O– – –
A t B t … t Z t 0 t 1 t
… t 9 t A
SELECT
END
:
SET
EXIT : MENU
:
: OK
2 Press , to set the next
character.
The next space flashes.
To correct a character, press </, until the character you want
to correct flashes, then reset it.
You can set up to 4 characters for the station name.
Press OK to confirm the station name.
7
8
OK
Press MENU to exit the menu.
MENU
continued
Presetting channels
25
Download from Www.Somanuals.com. All Manuals Search And Download.
If the picture is not clear
If the picture is not clear, you may use the Manual Fine Tuning (MFT)
function. After step 4, press M/m to select MFT. Press </, to get a clear
picture, then press MENU to exit the menu.
Tip
• The VCR must receive channel information for station names to appear
automatically.
Note
• When adjusting MFT, the menu may become difficult to read due to interference
from the picture being received.
Presetting channels
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/disabling programme positions
After setting the channels, you can change the programme positions as you like. If
any programme positions are unused or contain unwanted channels, you can disable
them.
You can also change the station names. If the station names are not displayed, you
can enter them manually.
Changing programme positions
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
Press MENU, then press M/m/</
MENU
1
, to highlight INSTALLATION
AUTO SET UP
and press OK.
MANUAL SET UP
SMARTLINK
VCR OUTPUT CH
: 2 1
OK
SELECT
END
:
SET
EXIT : MENU
:
: OK
Press M/m to highlight MANUAL
2
3
TV STATION TABLE
SET UP, then press ,.
PR
1
2
3
4
CH
NAME
OK
0 2 7
0 2 9
0 3 0
0 3 2
A A B –
L MN–
CDE –
I
J K –
5
SWAPPING : OK
EXIT : MENU
DELETE : CLEAR
Press M/m to highlight the row
containing the programme position
you want to change.
TV STATION TABLE
PR
1
2
3
4
CH
NAME
A A B –
L MN–
CDE –
OK
0 2 7
0 2 9
0 3 0
0 3 2
To display other pages for
programme positions 6 to 80, press
M/m repeatedly.
I
J K –
5
SWAPPING : OK
EXIT : MENU
DELETE : CLEAR
continued
Changing/disabling programme positions
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Press OK, then press M/m to move
4
5
TV STATION TABLE
to the desired programme position.
PR
1
2
3
4
CH
0 2 7
NAME
A A B –
OK
0 3 0
0 3 2
0 2 9
CDE –
I
J K –
L MN–
5
SWAPPING : OK
EXIT : MENU
Press OK to confirm the setting.
OK
To change the programme position of another station, repeat steps 3
through 5.
6
7
Press MENU to exit the menu.
MENU
Disabling unwanted programme positions
After presetting channels, you can disable unused programme positions. The disabled
positions will be skipped later when you press the PROG +/– buttons.
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
Press MENU, then press M/m/</
MENU
1
, to highlight INSTALLATION,
AUTO SET UP
and press OK.
MANUAL SET UP
SMARTLINK
VCR OUTPUT CH
: 2 1
OK
SELECT
END
:
SET
EXIT : MENU
:
: OK
Changing/disabling programme positions
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Press M/m to highlight MANUAL
2
3
4
TV STATION TABLE
SET UP, then press ,.
PR
1
2
3
4
CH
NAME
OK
0 2 7
0 2 9
0 3 0
0 3 2
A A B –
L MN–
CDE –
I
J K –
5
SWAPPING : OK
EXIT : MENU
DELETE : CLEAR
Press M/m to highlight the row
which you want to disable.
TV STATION TABLE
PR
1
2
3
4
CH
NAME
A A B –
L MN–
CDE –
OK
To display other pages for
programme positions 6 to 80, press
M/m repeatedly.
0 2 7
0 2 9
0 3 0
0 3 2
I
J K –
5
SWAPPING : OK
EXIT : MENU
DELETE : CLEAR
Press CLEAR.
CLEAR
TV STATION TABLE
The selected row will be cleared as
shown on the right.
PR
1
2
CH
0 2 7
NAME
A A B –
3
4
0 3 0
0 3 2
CDE –
I
J K –
5
SWAPPING : OK
EXIT : MENU
DELETE : CLEAR
Repeat steps 3 and 4 for any other programme positions you want to
disable.
5
6
Press MENU to exit the menu.
MENU
Note
• Be sure to select the programme position you want to disable correctly. If you
disable a programme position by mistake, you need to reset that channel manually.
continued
Changing/disabling programme positions
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the station names
You can change or enter the station names (up to 4 characters). The VCR must
receive channel information for station names to appear automatically.
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
Press MENU, then press M/m/</
MENU
1
, to highlight INSTALLATION
AUTO SET UP
and press OK.
MANUAL SET UP
SMARTLINK
VCR OUTPUT CH
: 2 1
OK
SELECT
END
:
SET
EXIT : MENU
:
: OK
Press M/m to highlight MANUAL
2
3
4
TV STATION TABLE
SET UP, then press ,.
PR
1
2
3
4
CH
NAME
OK
0 2 7
0 2 9
0 3 0
0 3 2
0 3 3
A A B –
L MN–
CDE –
I
J K –
5
– – – –
SWAPPING : OK
EXIT : MENU
DELETE : CLEAR
Press M/m to highlight the row
which you want to change or enter
the station name, then press ,.
To display other pages for
programme positions 6 to 80, press
M/m repeatedly.
MANUAL TUNING
PR
CH
MFT
NAME
:
:
:
:
5
OK
0 3 3
–
– – – –
SELECT
END
:
SET
EXIT : MENU
:
: OK
Press M/m to highlight NAME, then
press ,.
MANUAL TUNING
PR
CH
MFT
NAME
:
:
:
:
5
OK
0 3 3
–
– – – –
SELECT
END
:
SET
EXIT : MENU
:
: OK
Changing/disabling programme positions
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter the station name.
5
MANUAL TUNING
1 Press M/m to select a character.
Each time you press M, the
character changes as shown
below.
PR
CH
MFT
NAME
:
:
:
:
5
OK
0 3 3
–
O– – –
A t B t … t Z t 0 t 1 t
… t 9 t A
SELECT
END
:
SET
EXIT : MENU
:
: OK
2 Press , to set the next
character.
The next space flashes.
To correct a character, press </, until the character you want
to correct flashes, then reset it.
You can set up to 4 characters for the station name.
Press OK to confirm the new name.
6
7
OK
Press MENU to exit the menu.
MENU
Changing/disabling programme positions
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the clock
You must set the time and date on the VCR to use the timer features properly.
The Auto Clock Set function works only if a station in your area is broadcasting a
time signal.
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
Press MENU, then press M/m/</
MENU
1
, to highlight CLOCK SET and
press OK.
1 2 : 0 0
1
/ JAN / 2 0 0 3
WED
AUTO CLOCK
:
ON
OK
SELECT
END
:
SET
EXIT : MENU
:
: OK
Press M/m to set the hour.
2
3
OK
1 8 : 0 0
1
/ JAN / 2 0 0 3
WED
AUTO CLOCK
:
ON
SELECT
END
:
SET
EXIT : MENU
:
: OK
Press , to select the minutes and
set the minutes by pressing M/m.
OK
1 8 : 3 0
1
/ JAN / 2 0 0 3
WED
AUTO CLOCK
:
ON
SELECT
END
:
SET
EXIT : MENU
:
: OK
Setting the clock
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Set the day, month, and year in
sequence by pressing , to select
the item to be set, and press M/m to
select the digits, then press ,.
The day of the week is set
automatically.
4
5
OK
1 8 : 3 0 2 8 / SEP / 2 0 0 3
SUN
AUTO CLOCK
:
ON
SELECT
END
:
SET
EXIT : MENU
:
: OK
Press M/m to select ON for the
setting of the Auto Clock Set
function.
OK
1 8 : 3 0 2 8 / SEP / 2 0 0 3
SUN
The VCR automatically sets the
clock according to the time signal
broadcast between the channels
PR 1 to PR 5.
AUTO CLOCK
:
ON
SELECT
END
:
SET
EXIT : MENU
:
: OK
If you do not need the Auto Clock
Set function, select OFF.
Press MENU to exit the menu.
6
MENU
Tips
• If you set AUTO CLOCK to ON, the Auto Clock Set function is activated
whenever the VCR is turned off. The time is adjusted automatically by making
reference to the time signal from the station.
• To change the digits while setting, press < to return to the item to be changed, and
select the digits by pressing M/m.
Setting the clock
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
Playing a tape
Before you start...
Turn on your TV and set it to the video channel.
1
Insert a tape.
2
The VCR turns on and starts playing
automatically if you insert a tape with
its safety tab removed.
Press H (play).
3
When the tape reaches the end, it will rewind automatically.
OK
Additional tasks
To
Press
Stop play
x (stop)
Pause play
X (pause)
Resume play after pause
Fast-forward the tape
Rewind the tape
Eject the tape
X (pause) or H (play)
M (fast-forward) during stop
m (rewind) during stop
Z (eject)
To use the time counter
Press CLEAR at the point on the tape that you want to find later. The
counter in the display window resets to “0:00:00” or “00:00.” Search for the
point afterwards by referring to the counter.
SE830G, SE730G/I
SE230G/I
Hour
Minute Second
Hour
Minute
To display the counter on the TV screen, press
DISPLAY.
Playing a tape
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
• The counter resets to “0:00:00” or “00:00” whenever a tape is reinserted.
• The counter stops counting when it comes to a portion with no recording.
• Depending on your TV, the following may occur while playing an NTSC-recorded
tape:
–The picture becomes black and white.
–The picture shakes.
–No picture appears on the TV screen.
–Black streaks appear horizontally on the TV screen.
–The colour density increases or decreases.
• While setting the menu on the TV screen, buttons for playback on the remote
commander do not function.
Starting playback automatically with one button (One
Touch Play) (not available on SLV-SE230G/I)
If you use the SMARTLINK connection, you can turn on the TV, set the TV
to the video channel, and start playback automatically with one button.
Insert a tape.
1
The VCR automatically turns on.
If you insert a tape with its safety tab removed, the TV turns on and
switches to the video channel. Playback starts automatically.
Press H (play).
2
The TV turns on and switches to the video channel automatically.
Playback starts.
Tip
• When there already is a tape in the VCR, press ?/1 to turn on the VCR first. When
you press H (play), the TV turns on, the TV is set to the video channel, and
playback starts automatically in one sequence.
Note
• When you use the One Touch Play function, leave the TV on or in the standby
mode.
Playing a tape
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording TV programmes
Before you start...
Turn on your TV and set it to the video channel.
1
To record from a satellite or digital tuner, turn it on.
Insert a tape with its safety tab in place.
2
• To record a normal channel, press PROG +/– until the programme
position number you want appears in the display window.
• PROG
3
INPUT SELECT
• To record from other equipment connected to one or more of the
LINE inputs, press INPUT SELECT until the connected line
appears in the display window.
Press SP/LP to select the tape speed, SP or LP.
4
SP / LP
LP (Long Play) provides recording time twice as long as SP.
However, SP (Standard Play) produces better picture and audio
quality.
Recording TV programmes
36
Download from Www.Somanuals.com. All Manuals Search And Download.
To save a recording
To prevent accidental erasure, break off the
safety tab as illustrated. To record on the
same tape again, cover the tab hole with
adhesive tape.
Safety tab
Tips
• To select a programme position, you can use the programme number buttons on the
remote commander. For two-digit numbers, for example, press 2 and 3 to select
“PR 23.”
• If you connect additional equipment to a LINE connector or jack, you can select
the input signal using the INPUT SELECT or PROG +/– buttons.
• The
DISPLAY information appears on the TV screen indicating information
about the tape, but the information will not be recorded on the tape.
• If you do not want to watch TV while recording, you can turn off the TV. When
using a satellite or digital tuner, make sure to leave it on.
Notes
• The
DISPLAY information does not appear during still (pause) mode or slow-
motion playback.
• If a tape has portions recorded in both PAL and NTSC systems, the time counter
reading will not be correct. This discrepancy is due to the difference between the
counting cycles of the two video systems.
• When you insert a non-standard commercially available tape, the remaining time
may not be correct.
• The remaining time is intended for rough measurement only.
• About 30 seconds after the tape begins playback, the tape remaining time will be
displayed.
• To use the TV Direct Rec function, select SMARTLINK in the INSTALLATION
menu, then set TV DIRECT RECORD to ON.
Recording TV programmes
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording what you are watching on the TV (TV Direct
Rec) (not available on SLV-SE230G/I)
If you use the SMARTLINK connection, you can easily record what you are
watching on the TV (other than tapes being played on the VCR).
Press ?/1 to turn on the VCR.
1
2
Insert a tape with its safety tab in place.
Press z REC while you are watching a TV programme or external
3 source.
The TV indicator lights up and the VCR starts recording what you are
watching on the TV.
Tip
• The TV indicator appears in the display window after you press z REC in some
situations such as:
–when you are watching a source connected to the TV’s line input, or
–when the TV tuner preset data for the programme position is different from the
data in the VCR tuner preset.
Notes
• You cannot record what you are watching using this method when the VCR is in
the following modes; pause, timer standby, tuner preset, Auto Set Up, and
recording.
• When the TV indicator is lit in the display window, do not turn off the TV nor
change the TV programme position. When the TV indicator is not lit, the VCR
continues recording the programme even if you change the TV programme
position on the TV.
• To use the TV Direct Rec function, select SMARTLINK in the INSTALLATION
menu, then set TV DIRECT RECORD to ON.
Recording TV programmes
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording TV programmes using the Dial
Timer (SLV-SE830G only)
The Dial Timer function allows you to
make timer recordings of programmes
without turning on your TV. Set the
recording timer to record up to eight
programmes, including settings made with
other timer methods, that will be broadcast
within the next month. The recording start
time and recording stop time can be set at
one minute intervals.
?/1
DIAL TIMER
x
X
PROGRAM +/–
Before you start...
• Insert a tape with its safety tab in place. Make sure the tape is longer than the total recording
time.
• To record from a satellite or digital tuner, turn it on.
Press
DIAL TIMER.
DIAL TIMER
1
“DATE” and “TODAY” appear alternately in the display window.
If the date and time are not set, “DAY” will appear. See step 2 in the
Turn
DIAL TIMER to set the recording date.
DIAL TIMER
2
Recording TV programmes using the Dial Timer (SLV-SE830G only)
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Press
DIAL TIMER.
DIAL TIMER
3
“START” and the current time appear alternately in the display
window.
Turn
DIAL TIMER to set the recording start time.
DIAL TIMER
PROGRAM
4
5
You can set the recording start time in 15 minute intervals or adjust
the time in one minute intervals by pressing the PROGRAM +/–
buttons.
Press
DIAL TIMER.
DIAL TIMER
“STOP” and the recording stop time alternately appear in the
display window.
Turn
DIAL TIMER to set the recording stop time.
DIAL TIMER
PROGRAM
6
You can set the recording stop time in 15 minute intervals or adjust
the time in one minute intervals by pressing the PROGRAM +/–
buttons.
continued
Recording TV programmes using the Dial Timer (SLV-SE830G only)
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Press
DIAL TIMER.
DIAL TIMER
7
8
The programme position or LINE input appears in the display
window.
DIAL TIMER
Turn
DIAL TIMER to set the programme position.
To record from other equipment connected to one or more of the
LINE inputs, turn DIAL TIMER or press INPUT SELECT to
display the connected line in the display window.
INPUT SELECT
DIAL TIMER
Press DIAL TIMER to complete the setting.
“OK” appears in the display window for about five seconds.
The indicator appears in the display window and the VCR stands
9
by for recording.
To record from other equipment, leave the connected equipment
switched on.
To return to the previous step
To return to the previous step, press the PROGRAM + and – buttons on the
VCR at the same time during any of the Dial Timer settings.
To stop recording
To stop the VCR while recording, press x (stop).
To use the VCR after setting the timer
To use the VCR before a recording begins, just press ?/1. The
indicator
turns off and the VCR switches on. Remember to press ?/1 to reset the VCR
to recording standby after using the VCR.
You can also do the following tasks while the VCR is recording:
Recording TV programmes using the Dial Timer (SLV-SE830G only)
42
Download from Www.Somanuals.com. All Manuals Search And Download.
To set the clock
Hold down
DIAL TIMER so that “DAY” appears in the display
1 window. However, if the clock has already been set, the current setting
appears.
Turn
DIAL TIMER to set the day.
2
Press
DIAL TIMER.
3 “MONTH” appears in the display window.
Turn and press
DIAL TIMER to set the month, and then the year.
4 After you set the year, “CLOCK” appears in the display window again.
Turn and press
DIAL TIMER to set the hour and minute.
5
When you have finished setting the time, press
DIAL TIMER to start
6 the clock.
Tips
• To cancel a Dial Timer setting, press x (stop) on the VCR while you are making
the setting.
• The programme is recorded in the current tape speed mode. To change the tape
speed, press SP/LP before you complete the setting in step 9.
Notes
• If eight programmes have already been set using the VIDEO Plus+ system or the
TIMER PROGRAMMING menu, “FULL” appears in the display window for
about five seconds.
• The
indicator flashes in the display window when you complete the setting in
step 9 with no tape inserted.
• If you set the clock using the Auto Clock Set function and AUTO CLOCK is set to
ON, the clock will adjust itself to the incoming time signal regardless of
adjustments made with the Dial Timer. Be sure you have set the Auto Clock Set
correctly.
• When the time is set incorrectly, “ERROR” appears in the display window in step
9. Set the timer again from step 1.
• You cannot set the tape speed to AUTO using the Dial Timer. To select AUTO, set
the tape speed in the TIMER PROGRAMMING menu (see page 55).
continued
Recording TV programmes using the Dial Timer (SLV-SE830G only)
Download from Www.Somanuals.com. All Manuals Search And Download.
43
About the Demonstration Mode
The Dial Timer function has a Demonstration Mode that allows the user, such as a
salesperson, to enter more than eight examples of timer settings when demonstrating
the use of the Dial Timer. It cancels the “FULL” notice which appears if eight
programmes have already been set. Do not use the Demonstration Mode for making
timer recordings. Doing so may cause the settings to be inaccurate.
To activate the Demonstration Mode
Press X (pause) on the VCR while turning the
DIAL TIMER. “DEMO”
appears in the display window for a few seconds.
To cancel the Demonstration Mode
Turn the power off and unplug the mains lead. Although the Demonstration
Mode is cancelled, the timer settings entered while using the Demonstration
Mode will remain. Be sure to manually cancel the timer settings before you
use the Dial Timer or any other timer method after reconnecting the mains
Recording TV programmes using the Dial Timer (SLV-SE830G only)
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording TV programmes using the
VIDEO Plus+® system
The VIDEO Plus+ system is the feature that simplifies programming the VCR to
make timer recordings. Just enter the PlusCode number listed in the TV programme
guide. The date, times, and programme position of that programme are set
automatically. You can preset a total of eight programmes, including settings made
with other timer methods.
Before you start…
• Check that the VCR clock is set to the correct time and date.
• Insert a tape with its safety tab in place. Make sure the tape is longer than the total recording
time.
• To record from a satellite or digital tuner, turn it on.
• Turn on your TV and set it to the video channel.
• Set TIMER METHOD to VIDEOPLUS or VARIABLE in the EASY OPERATION menu
Press TIMER.
TIMER
1
• When you set TIMER METHOD
TIMER METHOD
to VARIABLE:
The TIMER METHOD menu
appears on the TV screen. Press
STANDARD
VIDEOPLUS
M/m to select VIDEOPLUS, then
press OK.
OK
SELECT
SET
:
: OK
EXIT : MENU
• When you set TIMER METHOD
to VIDEOPLUS:
The VIDEOPLUS menu appears
on the TV screen.
VIDEOPLUS
CODE – – – – – – – – –
CODE : 0 – 9
SET : OK
EXIT : MENU
continued
Recording TV programmes using the VIDEO Plus+® system
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the programme number
buttons to enter the PlusCode
number.
1
4
7
2
5
8
0
3
6
9
2
3
VIDEOPLUS
CODE 1 2 3 4 – – – – –
If you make a mistake, press
CLEAR and re-enter the correct
number.
CLEAR
CODE : 0 – 9
SET : OK
EXIT : MENU
Press OK.
PR DAY
START
STOP
V/P
–
–
–
–
–
–
The date, start and stop times,
programme position, tape speed and
PDC setting appear on the TV
screen.
3 5 S A 2 9 1 9 : 0 0 2 0 : 0 0
SP
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
OK
INPUT SELECT
CLEAR
• If “– –” appears in the “PR”
(programme) column (this may
happen for local broadcasts), you
have to set the appropriate
SELECT
END
:
SET
EXIT : MENU
:
: OK
programme position manually.
Press M/m to select the desired programme position.
• To record from other equipment connected to one or more of the
LINE inputs, press INPUT SELECT to display the connected line
in the “PR” position.
You will only have to do this operation once for the referred
channel. The VCR will then store your setting.
If the information is incorrect, press CLEAR to cancel the setting.
If you want to change the date, tape
speed and the PDC setting:
4
5
PR DAY
3 5 S A 2 9 1 9 : 0 0 2 0 : 0 0
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
START
STOP
V/P
ON
SP
–
–
–
–
–
OK
1 Press </, to select the item
you want to change.
2 Press M/m to reset it.
• To record the same programme
every day or the same day every
• To use the PDC function, set V/P to ON. For details about the
PDC function, see “Timer recording with PDC signals” on
SELECT
END
:
SET
:
: OK
EXIT : MENU
Press MENU to exit the menu.
MENU
Recording TV programmes using the VIDEO Plus+® system
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Press ?/1 to turn off the VCR.
6
The indicator appears in the display window and the VCR stands
by for recording.
To record from a decoder or other source, leave the connected
equipment switched on.
To stop recording
To stop the VCR while recording, press x (stop).
Daily/weekly recording
In step 4 above, press m to select the recording pattern. Each time you press
m, the indication changes as shown below. Press M to change the indication
in reverse order.
today t DLY (Monday to Sunday) t W-SA (every Saturday) ..... t
W-SU (every Sunday) t 1 month later t (dates count down) t today
Timer recording with PDC signals
Some broadcast systems transmit PDC (Programme Delivery Control)
signals with their TV programmes. These signals ensure that your timer
recordings are made regardless of broadcast delays, early starts, or broadcast
interruptions.
To use the PDC function, set V/P to ON in step 4 above. You can also use
the PDC function for a source connected to one or more of the LINE inputs.
To record satellite broadcasts
If you connect the satellite tuner and the VCR, you can record satellite
programmes.
Turn on the satellite tuner.
1
On the satellite tuner, select the satellite programme for which you want
2 to make a timer setting.
Keep the satellite tuner turned on until the VCR finishes recording the
3 satellite programme for which you have made a timer setting.
continued
Recording TV programmes using the VIDEO Plus+® system
47
Download from Www.Somanuals.com. All Manuals Search And Download.
To use the VCR after setting the timer
To use the VCR before a recording begins, just press ?/1. The indicator
turns off and the VCR switches on. Remember to press ?/1 to reset the VCR
to recording standby after using the VCR.
You can also do the following tasks while the VCR is recording:
To use the Auto Tape Speed function
In step 4 above, press m to select AUTO. When you are recording a
programme in the SP mode and the remaining tape length becomes shorter
than the recording time, the recording tape speed is automatically changed to
the LP mode. Note that some noise will appear on the picture when the tape
speed is changed. To operate this function correctly, the “TAPE SELECT”
Tips
• To set the line input video source, you can also use the INPUT SELECT button.
• You can set the extended time for the VIDEO Plus+ setting by 10, 20, 30, 40, 50, or
60 minutes. Set VIDEOPLUS EXTEND in the EASY OPERATION menu to the
Notes
• If the PDC signal is too weak or the broadcasting station failed to transmit PDC
signals, the VCR will start recording at the set time without using the PDC
function.
• The
and
indicators flash in the display window when you press ?/1 with
no tape inserted.
• When you set TIMER METHOD to STANDARD in the EASY OPERATION
menu, the VIDEOPLUS menu does not appear on the TV screen. Select
VIDEOPLUS or VARIABLE.
Recording TV programmes using the VIDEO Plus+® system
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the timer manually
You can preset a total of eight programmes, including settings made with other timer
methods.
Before you start…
• Check that the VCR clock is set to the correct time and date.
• Insert a tape with its safety tab in place. Make sure the tape is longer than the total recording
time.
• To record from a satellite or digital tuner, turn it on.
• Turn on your TV and set it to the video channel.
Press TIMER.
TIMER
1
• When you set TIMER METHOD
TIMER METHOD
to VARIABLE:
The TIMER METHOD menu
appears on the TV screen. Press
STANDARD
VIDEOPLUS
M/m to select STANDARD, then
press OK.
OK
SELECT
SET
:
: OK
EXIT : MENU
• When you set TIMER METHOD
to STANDARD:
The TIMER PROGRAMMING
menu appears on the TV screen.
PR DAY
START
STOP
V/P
–
–
–
–
–
–
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
SELECT
END
:
SET
EXIT : MENU
:
: OK
continued
Setting the timer manually
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Set the date, start and stop times,
programme position, tape speed and
PDC function:
2
PR DAY
START
STOP
V/P
–
–
–
–
–
–
3 5 – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
OK
1 Press , to select each item in
turn.
2 Press M/m to set each item.
To correct a setting, press < to
return to that setting and reset.
INPUT SELECT
SELECT
END
:
SET
EXIT : MENU
:
: OK
• To record the same programme
every day or the same day every week, see “Daily/weekly
• To use the PDC function, set V/P to ON. For details about the
PDC function, see “Timer recording with PDC signals” on
• To record from other equipment connected to one or more of the
LINE inputs, press INPUT SELECT to display the connected line
in the “PR” position.
Press MENU to exit the menu.
3
4
MENU
Press ?/1 to turn off the VCR.
The indicator appears in the display window and the VCR stands
by for recording.
To record from other equipment, leave the connected equipment
switched on.
To stop recording
To stop the VCR while recording, press x (stop).
Daily/weekly recording
In step 2 above, press m to select the recording pattern. Each time you press
m, the indication changes as shown below. Press M to change the indication
in reverse order.
today t DLY (Monday to Sunday) t W-SA (every Saturday) ..... t
W-SU (every Sunday) t 1 month later t (dates count down) t today
Setting the timer manually
50
Download from Www.Somanuals.com. All Manuals Search And Download.
To use the VCR after setting the timer
To use the VCR before a recording begins, just press ?/1. The
indicator
turns off and the VCR switches on. Remember to press ?/1 to reset the VCR
to recording standby after using the VCR.
You can also do the following tasks while the VCR is recording:
To use the Auto Tape Speed function
In step 2 above, press m to select AUTO. When you are recording a
programme in the SP mode and the remaining tape length becomes shorter
than the recording time, the recording tape speed is automatically changed to
the LP mode. Note that some noise will appear on the picture when the tape
speed is changed. To operate this function correctly, the “TAPE SELECT”
setting in the USER SET menu must be accurate (see page 63).
Tips
• To set the line input video source, you can also use the INPUT SELECT button.
• Even if you set TIMER METHOD to VIDEOPLUS in the EASY OPERATION
menu, you can set the timer manually. Press MENU to select TIMER
PROGRAMMING, then go to step 2.
Notes
• When setting the timer with PDC signals, enter the start and stop times exactly as
indicated in the TV programme guide. Otherwise, the PDC function will not work.
• If the PDC signal is too weak or the broadcasting station failed to transmit PDC
signals, the VCR will start recording at the set time without using the PDC
function.
• The
and
indicators flash in the display window when you press ?/1 with
no tape inserted.
Setting the timer manually
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
Troubleshooting
If you have any questions or problems not covered below, please consult your nearest
Sony service facility.
Symptom
Remedy
The ?/1 (on/standby)
• Connect the mains lead to the mains securely.
switch does not function.
The power is turned on
but the VCR does not
operate.
• Moisture condensation has occurred. Turn the power off,
unplug the mains lead and leave the VCR to dry for over
three hours.
The VCR is plugged in
but the display window
remains dark.
The clock has stopped
and “– –:– –” appears in
the display window.
• The clock stops if the VCR is disconnected from the mains.
Reset the clock (and timer).
The playback picture
does not appear on the
TV screen.
• Make sure the TV is set to the video channel. If you are
using a monitor, set it to video input.
• If the VCR is connected to the TV with the Scart cable,
make sure the VIDEO indicator is lit in the display
window. Use the t TV/VIDEO button on the remote
commander to light up the VIDEO indicator.
The picture is not clear.
• Existing broadcasts may interfere with the VCR. Reset the
• Adjust the tracking with the PROGRAM +/– buttons on the
VCR.
• The video heads are dirty (see the last page of
Troubleshooting). Clean the video heads using a Sony
video head cleaning cassette. If a Sony cleaning cassette is
not available in your area, have the heads cleaned at your
nearest Sony service facility (a standard service charge will
be required). Do not use a commercially available liquid
type cleaning cassette other than Sony’s, as it may damage
the video heads.
• The video heads may have to be replaced. Consult your
local Sony service facility for more information.
The picture rolls
vertically during picture
search.
• Adjust the vertical hold control on the TV or monitor.
The picture has no
sound.
• The tape is defective.
• If you made A/V connections, check the audio cable
connection.
continued
Troubleshooting
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
The sound from a tape
recorded with the VCR is
not in stereo or the
STEREO indicator in the
display window is
flashing.
• Adjust the tracking.
• The video heads are dirty. Clean the video heads using a
Sony video head cleaning cassette as explained above.
No TV programme
appears on the TV
screen.
• Make sure the TV is set to the video channel. If you are
using a monitor, set it to video input.
• Existing broadcasts may interfere with the VCR. Reset the
• Select the correct source with the INPUT SELECT button.
Select a programme position when recording TV
programmes; select a line input when recording from other
equipment.
TV reception is poor.
• Make sure the aerial cable is connected securely.
• Adjust the TV aerial.
The tape starts playing as • The safety tab has been removed. To record on this tape,
The tape is ejected when • The safety tab has been removed. To record on this tape,
you press z REC.
Nothing happens when
• Make sure the tape is not at its end.
you press z REC.
The timer does not
operate.
• Check that the clock is set.
• Make sure a tape has been inserted.
• Check that the safety tab has not been removed.
• Make sure the tape is not at its end.
• Make sure a programme has been set for timer recording.
• Make sure your timer settings are past the current time.
• Check that the digital tuner is turned on.
• Check that the satellite tuner is turned on.
• The clock stops if the VCR is disconnected from the mains.
Reset the clock and timer.
• Turn the power off and unplug the mains lead.
The VIDEOPLUS menu • Check that TIMER METHOD in the EASY OPERATION
or the TIMER
menu is set correctly (see page 64).
PROGRAMMING menu
does not appear.
Troubleshooting
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
The PDC function does
not operate properly.
• Check that the clock and the date are set correctly.
• Check that the PDC time you set is the correct one (there
might be a mistake in the TV programme guide). If the
broadcast you wanted to record did not send the good PDC
information, the VCR will not start recording.
• If the reception is poor, the PDC signal might be altered
and the VCR might not start recording.
A tape cannot be
inserted.
• Check that a tape is not already in the tape compartment.
The remote commander • Make sure you are pointing the remote commander at the
does not function.
remote sensor on the VCR.
• Replace all the batteries in the remote commander with
new ones if they are weak.
• Make sure the [TV] / [VIDEO] remote control switch is set
correctly.
The selected input line
connector number does
not appear in the display
window.
• Press INPUT SELECT to display the connected line.
The tracking meter does • The recording condition of the tape is very poor and
not appear on the TV
tracking cannot be adjusted.
screen.
You cannot control other • Set your TV’s code number. The code number may change
TVs.
when you replace the batteries of the remote commander.
The display window
becomes dim.
• The display window automatically becomes dim when the
VCR is in standby or timer recording mode.
The VCR needs to be
cleaned.
• Clean the cabinet, panel and controls with a dry, soft cloth,
or a soft cloth slightly moistened with a mild detergent
solution. Do not use any type of solvent, such as alcohol or
benzine.
The Line Through
function does not
operate.
continued
Troubleshooting
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptoms caused by contaminated video heads
• No picture (or
black & white
• Normal picture
• Rough picture
• Unclear picture
screen appears)
initial
contamination
terminal
Troubleshooting
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
AUDIO (OUT) R, L*2
System
Phono jack (2)
Channel coverage
Rated output level: 327 mVrms
Load impedance: 47 kilohms
Output impedance: less than 10 kilohms
PAL (I)
VHF IA to IJ, SA10 to SA13*
UHF B21 to B69
*1 SLV-SE830G only
CATV S01 to S05, S1 to S20*
HYPER S21 to S41*
*2 not available on SLV-SE230G/I
RF output signal
UHF channels 21 to 69
Aerial out
75-ohm asymmetrical aerial socket
Tape speed
General
Power requirements
220 – 240 V AC, 50 Hz
Power consumption
• SLV-SE230G/I
15 W
SP:PAL23.39 mm/s (recording/playback)
NTSC33.35 mm/s (playback only)
LP:PAL11.70 mm/s (recording/playback)
NTSC16.67 mm/s (playback only)
EP:NTSC11.12 mm/s (playback only)
Maximum recording/playback time
10 hrs. in LP mode (with E300 tape)
Rewind time
1.2 W (POWER SAVE is set to ECO2,
minimum)
• SLV-SE830G, SE730G/I
17 W
1.3 W (POWER SAVE is set to ECO2,
minimum)
Operating temperature
5°C to 40° C
Approx. 1 min. (with E180 tape)
Storage temperature
* SLV-SE730I and SE230I only
–20°C to 60°C
Inputs and outputs
LINE-1 (EURO AV)
21-pin
Dimensions including projecting parts and
controls (w/h/d)
Approx. 360 × 95 × 245 mm
(SLV-SE230G/I)
Video input: pin 20
Approx. 430 × 96 × 245 mm
(SLV-SE730G/I)
Approx. 430 × 96 × 253 mm
(SLV-SE830G)
Audio input: pins 2 and 6
Video output: pin 19
Audio output: pins 1 and 3
LINE-2/LINE-3
Mass
21-pin
Video input: pin 20
Approx. 2.8 kg (SLV-SE230G/I)
Approx. 3.1 kg (SLV-SE830G and
SE730G/I)
Audio input: pins 2 and 6
t LINE-2 L o R*1
VIDEO IN, phono jack (1)
Input signal: 1 Vp-p, 75 ohms,
unbalanced, sync negative
AUDIO IN, phono jack (2)
Input level: 327 mVrms
Input impedance: more than 47 kilohms
Supplied accessories
Remote commander (1)
R6 (size AA) batteries (2)
Aerial cable (1)
Design and specifications are subject to
change without notice.
Specifications
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Operations
Playing/searching at various speeds
Before you start…
Playback options
Operation
View the picture during
fast-forward or rewind
During fast-forward, hold down M (fast-forward). During
rewind, hold down m (rewind).
Play at high speed
• During playback, press M (fast-forward) or m (rewind)
on the remote commander.
• During playback, hold down M (fast-forward) or
m (rewind). When you release the button, normal
playback resumes.
Play at twice the normal
speed
During playback, press ×2.
Play in slow motion
Play frame by frame
During playback, press y SLOW.
During pause, press M (fast-forward) or m (rewind)* on
the remote commander.
* SLV-SE830G only
To resume normal playback
Press H (play).
Using the shuttle ring
(SLV-SE830G only)
JOG
Shuttle ring
With the shuttle ring, you can
operate a variety of playback
options. There are two ways for
using the shuttle ring, normal mode
and jog mode.
Playing/searching at various speeds
52
Download from Www.Somanuals.com. All Manuals Search And Download.
To use the shuttle ring in normal mode
During playback or pause, turn the shuttle ring clockwise or anticlockwise.
Each change in the shuttle ring position changes the playback mode in the
following way.
Pause
Slow motion
Slow motion
in reverse
Normal speed
in reverse
Normal speed
(Initial speed)
Double speed
in reverse
Double speed
High speed
High speed in
reverse
To use the shuttle ring in jog mode
Use this mode for frame-by-frame playback.
Press JOG to enter the jog mode. The JOG button lights up. If you change
to the jog mode during any playback mode, playback pauses so you can see a
still picture. Each change in the shuttle ring position shifts the picture one
frame. To shift frames in reverse, turn the shuttle ring anticlockwise. The
frame shift speed depends on the speed you turn the shuttle ring.
To resume normal mode, press JOG again. The JOG button turns off.
Tip
• Adjust the picture using the PROGRAM +/– buttons on the VCR if:
–Streaks appear while playing in slow motion.
–Bands appear at the top or bottom while pausing.
–The picture shakes while pausing.
To set tracking to the centre position, press both buttons (+/–) at the same time.
Notes
• The sound is muted during these operations.
• In the LP mode, noise may appear or there may be no colour.
• If the playback mode mark does not appear on the TV screen, press
• The picture may show noise when playing at high speed in reverse.
DISPLAY.
• The picture returns to normal playback from slow motion in reverse in 30 seconds.
Playing/searching at various speeds
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the recording duration time
After you have started recording in the normal way, you can have the VCR stop
recording automatically after a specified duration.
Before you start…
While recording, press z REC.
1
The indicator appears in the display window.
Press z REC repeatedly to set the duration time.
2
In SP mode
Each press advances the time in increments of 30 minutes.
0:30
1:00
4:00
4:30
Normal recording
In LP mode
Each press advances the time as shown below.
Normal recording
0:30
1:00
8:00
9:00
The tape counter decreases minute by minute to 0:00, then the VCR stops
recording and turns off automatically.
To extend the duration
Press z REC repeatedly to set a new duration time.
To cancel the duration
Press z REC repeatedly until the indicator disappears and the VCR
returns to the normal recording mode.
To stop recording
To stop the VCR while recording, press x (stop).
Note
• You cannot display the current tape time in the display window when setting the
recording duration time.
Setting the recording duration time
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking/changing/cancelling timer
settings
Before you start…
• Turn on your TV and set it to the video channel.
Press ?/1 to turn on the VCR.
1
Press MENU, then press M/m to highlight TIMER PROGRAMMING
2 and press OK.
• If you want to change or cancel a
PR DAY
3 5 S A 2 9 1 9 : 0 0 2 0 : 0 0
2 9 S A 2 9 2 1 : 0 0 2 1 : 3 0 –
3 0 S A 1 2 : 0 0 1 3 : 3 0 –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
START
STOP
V/P
ON
setting, go on to the next step.
• If you do not need to change or cancel
the settings, press MENU, then turn
off the VCR to return to recording
standby.
SP
–
–
–
–
–
6
SELECT
END
:
SET
EXIT : MENU
:
: OK
Press M/m to select the setting you want
3 to change or cancel, then press ,.
PR DAY
START
STOP
V/P
ON
3 5 S A 2 9 1 9 : 0 0 2 0 : 0 0
2 9 S A 2 9 2 1 : 0 0 2 1 : 3 0 –
3 0 S A 1 2 : 0 0 1 3 : 3 0 –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
SP
–
–
–
–
–
The PR number on the selected row
flashes.
6
SELECT
END
:
SET
EXIT : MENU
:
: OK
• To change the setting, press </, to select the item you want to
change, then press M/m to reset it.
4
5
• To cancel the setting, press CLEAR.
Press MENU to exit the menu.
If any settings remain, turn off the VCR to return to recording standby.
continued
Checking/changing/cancelling timer settings
55
Download from Www.Somanuals.com. All Manuals Search And Download.
When the timer settings overlap
The programme that starts first has priority and the second programme starts
recording only after the first programme has finished. If the programmes
start at the same time, the programme listed first in the menu has priority.
Programme 1
Programme 2
about 20 seconds
will be cut off
Programme 1
Programme 2
about 20 seconds will be cut off
Checking/changing/cancelling timer settings
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording stereo and bilingual
programmes (not available on SLV-SE230G/I)
In the NICAM system
This VCR receives and records stereo and bilingual programmes based on
the NICAM system (NICAM appears on the TV screen). When a stereo or
bilingual programme is received, the STEREO indicator appears in the
display window.
To record a NICAM programme, NICAM in the USER SET menu should be
To select the sound while recording
Press AUDIO MONITOR to select the sound you want.
Stereo programmes
To listen to
Stereo
On-screen display
NICAM, STEREO
NICAM, LCH
Display window
STEREO
Left channel
Right channel
STEREO
NICAM, RCH
STEREO
Left and right channels* NICAM, LCH + RCH STEREO
* Usually the mixed sound of left and right channels
Bilingual programmes
To listen to
Main
On-screen display
NICAM, MAIN
NICAM, SUB
Display window
STEREO
Sub
STEREO
Main and sub
Standard sound*
NICAM, MAIN/SUB
NICAM, MONO
STEREO
STEREO
* Usually the main sound (monaural)
continued
Recording stereo and bilingual programmes (not available on SLV-SE230G/I)
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the sound during Hi-fi playback
Press AUDIO MONITOR to select the sound you want.
To listen to
Stereo
On-screen display
STEREO
LCH
Display window
STEREO
Left channel
Right channel
Mix sound*
Mono sound
STEREO
RCH
STEREO
MIX
STEREO
MONO
No indicator
* The mixed sound of left and right channels, and the normal mono audio track
How sound is recorded on a video tape
The VCR records sound onto two separate tracks. Hi-fi audio is recorded
onto the main track along with the picture. Monaural sound is recorded onto
the normal audio track along the edge of the tape.
Stereo
Usually mixed
Bilingual
Usually main sound
left/right channels
Normal audio track
(monaural)
Hi-fi audio track
(main track)
Stereo sound
(left/right channels)
Main (left channel)
Sub (right channel)
Notes
• To listen to playback sounds in stereo, you must use the Scart or AUDIO OUT
connections.
• When you play a tape recorded in monaural, the sound is heard in monaural
regardless of the AUDIO MONITOR setting.
Recording stereo and bilingual programmes (not available on SLV-SE230G/I)
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Searching using the index function
(not available on SLV-SE230G/I)
The VCR automatically marks the tape with an index signal at the point where each
recording begins. Use these signals as references to find a specific recording.
To find a specific recording by scanning (Index scan)
Insert an indexed tape into the VCR.
1
Press ./> (index search). The
2 VCR starts scanning each recording for
INDEX SCAN : BB
five seconds in the corresponding
direction.
Press H (play) to start playback when you find the desired point.
3
To search a specific recording (Index search)
Insert an indexed tape into the VCR.
1
2
Press ./> (index search) twice.
• To search ahead, press > (index
search) twice.
INDEX SEARCH : BB + 0 2
• To search backwards, press . (index
search) twice.
Press ./> (index search) depending on the direction where your
3 desired programme is located.
Each time you press the button, the number increases or decreases up to
20, respectively.
The VCR starts searching, and playback starts automatically from that
4 point.
To stop searching
Press x (stop).
continued
Searching using the index function (not available on SLV-SE230G/I)
Download from Www.Somanuals.com. All Manuals Search And Download.
59
Notes
• No index signal will be added when recording starts from recording pause.
However, an index signal will be marked if you change the programme position
during recording pause.
• When you press . (index search), if there is nothing recorded before the
selected index signal, playback may not start exactly at the index signal.
Searching using the index function (not available on SLV-SE230G/I)
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the picture
Adjusting the tracking
Although the VCR automatically adjusts the
tracking when playing a tape, distortion may
occur if the recording is in poor condition. In
this case, manually adjust the tracking.
During playback, press PROGRAM +/– on
the VCR to display the tracking meter. The
distortion should disappear as you press one
of the two buttons. To resume automatic
tracking adjustments, eject the tape and re-
insert it.
TRACKING – – – – – – – – – – – –
Tracking meter
Adjusting the picture sharpness (Smart trilogic)
You can automatically adjust the sharpness of the picture.
During playback, press MENU, then press M/m/</, to highlight
1 USER SET and press OK.
Press M/m to highlight SMART
2 TRILOGIC, then press ,.
OSD
: ON
TAPE SELECT
COLOUR SYSTEM
FORMAT 1 6 : 9
NICAM
POWER SAVE
SMART TRILOGIC
: E 1 8 0
: AUTO
: AUTO
: ON
: OFF
: ON
SELECT
END
:
SET
EXIT : MENU
:
: OK
Press M/m to set SMART TRILOGIC to
3 ON or OFF.
PICTURE
• ON: Picture sharpness is automatically
adjusted.
SMART TRILOGIC : OFF
• OFF: Adjust the picture sharpness
manually.
To soften the picture, press <.
To sharpen the picture, press ,.
SOFTEN
SHARPEN
– – – – – – – – – – – – – – – – – – – – –
ON/OFF
END
:
SET
:
: OK
EXIT : MENU
Press MENU to return to the original screen.
4
Adjusting the picture
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Reducing the VCR’s power consumption
You can turn off the indicators in the display window when the VCR is off (standby
mode) to reduce the VCR’s power consumption.
Press MENU, then press M/m/</, to highlight USER SET and press
1 OK.
Press M/m to highlight POWER SAVE.
2
Press , to set to ECO1 or ECO2, then
3 press OK.
OSD
: ON
• ECO1: To reduce the power
consumption.
• ECO2: To reduce the power
consumption to a minimum.
TAPE SELECT
COLOUR SYSTEM
FORMAT 1 6 : 9
NICAM
POWER SAVE
SMART TRILOGIC
: E 1 8 0
: AUTO
: AUTO
: ON
: ON
: ON
SELECT
END
:
SET
:
: OK
EXIT : MENU
To turn on the indicators in the display window
Set POWER SAVE to OFF in step 3.
Notes
• When the VCR stands by for recording, the
indicator in the display window
remains lit even when POWER SAVE is set to ECO1 or ECO2.
• The Line Through function will not operate properly if POWER SAVE is set to
ECO2. Set POWER SAVE to OFF or ECO1 to ensure proper operation.
Reducing the VCR’s power consumption
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing menu options
Press MENU, then select USER SET or EASY OPERATION and press
1 OK.
OSD
: ON
VPS / PDC DEFAULT
VIDEOPLUS+ EXTEND
AUTO POWER OFF
TIMER METHOD
: OFF
: OFF
: OFF
TAPE SELECT
COLOUR SYSTEM
FORMAT 1 6 : 9
NICAM
: E 1 8 0
: AUTO
: AUTO
: ON
: VARIABLE
POWER SAVE
SMART TRILOGIC
: OFF
: ON
SELECT
END
:
SET
EXIT : MENU
:
SELECT
END
:
SET
EXIT : MENU
:
: OK
: OK
Press M/m to select the option.
2
3
Press , to change the setting, then press OK.
Menu choices
Initial settings are indicated in bold print.
USER SET
Menu option
Set this option to
• ON to display the menu on the TV screen.
OSD
• OFF to disappear the menu from the TV screen.
TAPE SELECT
• E180 to use an E-180 or shorter type tape.
• E240 to use an E-240 type tape.
• E260 to use an E-260 type tape.
• E300 to use an E-300 type tape.
COLOUR SYSTEM • AUTO to select the colour system automatically.
• PAL to use the tape recorded in the PAL colour system.
• B/W to use the tape recorded in black and white.
FORMAT 16:9
• AUTO when you use a wide screen TV. The VCR
automatically detects if programmes being played back
or recorded are in normal or wide screen format.
• ON if the VCR cannot detect wide screen TV
programmes with AUTO. The VCR always plays back
and records in wide screen format.
• OFF if you are not using a wide screen TV.
NICAM
• ON to record NICAM broadcasts on the hi-fi audio
track.
• OFF to record standard sound on the hi-fi audio track.
continued
Changing menu options
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu option
Set this option to
POWER SAVE
• ECO1 to turn off the indicators in the display window to
conserve the VCR’s power.
• ECO2 to turn off the indicators in the display window
during standby mode to reduce the VCR’s power
consumption to a minimum. For using the Line Through
function, select ECO1 or OFF.
• OFF to turn on the indicators in the display window
while the VCR is standing by.
SMART TRILOGIC • ON to automatically adjust the sharpness of the picture.
• OFF to manually adjust the sharpness of the picture.
EASY OPERATION
Menu option
Set this option to
VPS/PDC
DEFAULT
• OFF to deactivate the PDC function.
• ON to activate it.
VIDEOPLUS
EXTEND
• OFF to deactivate the VIDEO Plus+ Extend function.
• 10/20/30/.../60 (minutes) to extend the time of the
VIDEO Plus+ setting by the selected amount of time.
AUTO POWER OFF • OFF to deactivate the Auto Power Off function.
• 2HOUR/3HOUR to turn the VCR off automatically if no
signal is received and you do not press any of the buttons
during this time.
TIMER METHOD
• VARIABLE to display the TIMER METHOD menu for
selecting STANDARD or VIDEOPLUS when pressing
the
• STANDARD to display the TIMER PROGRAMMING
menu when pressing the TIMER button.
• VIDEOPLUS to display the VIDEOPLUS menu when
pressing the TIMER button.
TIMER button.
Changing menu options
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Editing
Connecting to a VCR or stereo system
How to connect to record on this VCR
Connect the line outputs of the other VCR to the input connector of this
VCR. Refer to the examples A through C and choose the connection that
best suits your VCR.
Example A
TV
Your VCR (Recorder)
LINE-1 (EURO AV)
Other VCR (Player)
Scart
(EURO-AV)
Scart cable (not supplied)
: Signal flow
Example B (SLV-SE830G only)
Your VCR (Recorder)
TV
t LINE-2 L o R
(open cover to connect)
LINE OUT
Audio/video cable (not supplied)
Other VCR (Player)
: Signal flow
continued
Connecting to a VCR or stereo system
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Example C
Your VCR (Recorder)
LINE-3*1 or LINE-2*2
TV
Other VCR (Player)
Scart
(EURO-AV)
Scart cable (not supplied)
: Signal flow
How to connect to a stereo system (SLV-SE830G only)
Connect the t LINE-2 L o R jacks on this VCR to the audio output jacks
on the stereo system, using an audio cable (not supplied).
Notes
• Make sure you connect the plugs to jacks of the same colour.
• If the other VCR is a monaural type, leave the red plugs unconnected.
• If you connect this VCR to both the LINE IN and LINE OUT jacks of the other
VCR, select the input correctly to prevent a humming noise.
• If the other VCR does not have a Scart (EURO-AV) connector, use an adequate
cable instead and connect the cable to the line out jacks of the other VCR.
• When you connect another VCR to the LINE-3*1 or LINE-2*2 connector, press
INPUT SELECT to display “L3”*1 or “L2”*2 in the display window.
*1 SLV-SE830G only
*2 SLV-SE730G/I and SE230G/I only
Connecting to a VCR or stereo system
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic editing
When recording on this VCR
Before you start editing
REC z
• Turn on your TV and set it to the video
channel.
• Press INPUT SELECT to display the
connected line in the display window.
• Press SP/LP to select the tape speed, SP or LP.
X
Insert a source tape with its safety tab removed into the other (playback)
1 VCR. Search for the point to start playback and set it to playback pause.
Insert a tape with its safety tab in place into this (recording) VCR.
2 Search for the point to start recording and press X (pause) to set it to
playback pause.
Press REC z on this VCR to set it to recording pause.
3
To start editing, press the X (pause) buttons on both VCRs at the same
4 time.
To stop editing
Press the x (stop) buttons on both VCRs.
Tip
• To cut out unwanted scenes while editing, press X (pause) on this VCR when an
unwanted scene begins. When it ends, press X (pause) again to resume recording.
Basic editing
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio dubbing (SLV-SE830G only)
This feature lets you record over the normal
AUDIO DUB
audio track. The monaural sound previously
recorded is replaced while the original hi-fi
sound remains unchanged. Use this feature
to add commentary to a tape that you have
recorded with a camcorder.
X
t LINE-2 L o R
Before you start...
• Open the t LINE-2 L o R jacks cover on the
front panel and connect a playback source.
• Turn on the TV and set it to the video channel.
Insert a source tape into your stereo system (or the playback VCR).
1 Search for the point to start playback and set it to playback pause.
Insert a prerecorded tape with its safety tab in place into this (recording)
2 VCR. Search for the start of the section to be replaced and press
X (pause).
The VCR enters pause mode.
Press AUDIO DUB.
3
“A_DUB” and the indicator appears in the display window.
To start editing, press the X (pause) buttons on this VCR and the stereo
4 system (or other VCR) at the same time.
After you use this feature, the audio in playback mode is automatically
set to monaural.
To stop editing
Press x (stop) on this VCR and the stereo system (or other VCR).
Audio dubbing (SLV-SE830G only)
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
L
S
Adjusting
LP mode 36
Safety tab 38
Scart connection 17
Searching
picture 61
tracking 61
Aerial hookup 16
Audio dubbing 68
Audio track 58
Auto Clock Set 20
Auto Set Up 20
at various speeds 52
using the index function 59
Smart trilogic 61
SMARTLINK
NexTView Download 18
One Touch Menu 18
One Touch Timer 18
SP mode 36
M
Manual fine tuning 26
Monaural 57
Monitoring
during playback 58
during recording 57
C
Changing the programme
position 27
Changing the station name 30
Cleaning the video heads 69
Clock setting 32
N
NICAM broadcasts 57
Normal audio track 58
Stereo 57
O
T
Colour system
Optional setting 63
compatible colour systems
Connecting
Timer setting 49
cancelling 55
changing 55
checking 55
using the Dial Timer 40
using the VIDEOPlus+
system 45
P
PDC (Programme Delivery
Control) 47
Playback 34
to a TV with a Scart
to digital tuner 19
to satellite tuner 19
Counter 34
at various speeds 52
frame-by-frame 52
selecting the sound 58
slow motion 52
V
Power save 62
Preset download 22
Presetting channels 24
VIDEOPLUS
recording 45
D
Demonstration 44
Dial Timer 40
Disabling the programme
positions 28
R
W
Recording 36
Wide screen format 63
bilingual programmes 57
duration time 54
saving 38
stereo programmes 57
timer setting 49
E
Editing 65
using the Dial Timer 40
using the VIDEOPlus+
system 45
what you are watching on
the TV 39
H
Hi-fi audio track 58
I
while watching another
programme 37
Index scan 59
Index search 59
RF channel 20
Index
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide
When all of the receivable channels are
1 Connecting the VCR
preset, the menu disappears from the TV
screen. You can rearrange the programme
position in any order (see “Changing/
3 Setting the clock
1
1... Press MENU, then press M/m/</, to
highlight CLOCK SET and press OK.
2... Press M/m to set the hour, then press ,.
LINE-1
(EURO AV)
4
3... Press M/m to set the minutes. Set the
day, month, and year in sequence by
pressing , to select the item to be set,
and press M/m to select the digits, then
press OK.
2
3
4... Press MENU.
:Signal flow
1 ...Connect the aerial to of the VCR.
Now you can operate your VCR.
2 ...Connect and the aerial input of your
TV using the supplied aerial cable.
3 ...For better picture and sound, connect
LINE-1 (EURO AV) to your TV using a
Scart cable if your TV has a Scart
(EURO-AV) connector.
2 Using the Auto Set Up function
1 ...Turn on your TV and set it to the video
channel.
If your TV does not have a Scart
(EURO-AV) connector, tune the TV to
channel 21 (the initial RF channel of this
VCR). Refer to your TV’s manual for
TV tuning instructions. If the picture
does not appear clearly, see “To change
2 ...Connect the mains lead to the mains.
3 ...Press OK.
Sony Corporation
AC68-02034P
Download from Www.Somanuals.com. All Manuals Search And Download.
|