3-274-295-13(1)
Getting Started
Basic Operations
Various Recording Modes
Playback/Erasing
IC Recorder
Operating Instructions
Owner’s Record
Editing Messages
Utilizing the Menu Function
Utilizing Your Computer
Troubleshooting
Additional Information
Index
The model number is located at the rear panel and the
serial number is located inside the battery compartment.
Record these numbers in the spaces provided below.
Refer to these numbers whenever you call upon your Sony
dealer regarding this product.
Model No.
Serial No.
ICD-UX70/UX80
© 2007 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁ
You are cautioned that any changes or
modifications not expressly approved in
this manual could void your authority to
operate this equipment.
Checking the contents
of the package
IC Recorder (1)
LR03 (size AAA) alkaline battery (1)
Stereo headphones (1)
USB connection support cable (1)
Operating Instructions
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢂ
Rear
Index to Parts and
Controls
Refer to the pages indicated in
parentheses for details.
Front
Operation indicator (14, 16, 17, 23, 38,
57)
Built-in microphones (stereo) (16)
Display window (8)
Control key (, /VOL (volume) +,
VOL –)/ENT (enter) button*1
(folder)/MENU button (16, 23, 30,
31, 32, 46)
(headphone) jack*2 (16, 18, 23, 24,
55)
(microphone) jack (20, 21)
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢃ
1
*
How to use the control key
Press the key toward the left or right to
adjust the volume.
(record/pause) button (16, 17, 19,
35)
(stop) button (17, 24, 25, 28, 31, 32)
Also use the key to change the menu
settings or to select a folder. In the
menu setting window or folder selection
window, press the key upward or
downward to select the item or the folder
you want, and then press the center of the
key (ENT) to confirm the setting.
(cue/fast forward) button (23, 24,
25)
(play/stop) button (17, 23, 25)
(review/fast backward) button
(17, 23, 24, 25)
(repeat) A-B button (23, 27)
HOLD switch*3
DPC switch (23, 26, 36)
Opening for a handstrap (A
handstrap is not supplied.)
USB cap
Speaker
Battery compartment (11)
2
*
Connect the supplied or commercially
available stereo headphones to the
(headphone) jack. If unwanted noise is
heard, wipe the headphones plug clean.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢄ
3
*
When you slide the HOLD switch in
the direction of the arrow in the stop
mode, the IC recorder turns off within a
few seconds. To turn the IC recorder on,
slide the HOLD switch in the opposite
direction from that of the arrow. During
recording and playback slide the switch
in the direction of the arrow to lock all the
functions of all the buttons so that you can
prevent inadvertent operations.
Display window
Operation mode indicator
Displays the following, depending on
the current operation mode
: stop
: playback
: recording
: recording standby/recording
pause
: recording with the VOR
function
: recording pause with the
VOR function (flashing)
If you press (record/pause) to
pause recording when“VOR”is set to
“ON”in the menu, only“
”flashes.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢅ
: review/fast backward,
cue/fast forward
: going backward/forward
continuously
Folder name/ Message title
name/ Artist name indication
Press the control key toward or
to display a folder name, message
title name, and artist name in
sequence.
Recording mode indicator
Displays the recording mode set
using the menu when the IC recorder
is in the stop mode, and displays
the current recording mode when
the IC recorder is in the playback or
recording mode.
: Standard play stereo recording
mode with high quality sound
: Standard play stereo recording
mode
: Long play stereo recording
mode
: Standard play monaural
recording mode
: Long play monaural recording
mode
Elasped time/Remaining time/
Recording date and time indication
Selected message number/Total
number of messages in the folder
Microphone sensitivity indicator
Displays the microphone sensitivity.
(high) : To record at a meeting or
in a quiet/spacious place.
(low) : To record for dictation or in
a noisy place.
Remaining battery indicator
When a dry battery is used, the
indicator shows the remaining
battery power.
Alarm indicator
Appears when the alarm is set for a
message.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢆ
Remaining recording time indication
Displays the remaining recording
time in hours, minutes, and seconds.
If there is more than 10 hours time
remaining, the time is displayed in
hours.
If there is more than 10 minutes and
less than 10 hours time remaining,
the time is displayed in hours and
minutes.
If there is less than 10 minutes time
remaining, the time is displayed in
minutes and seconds.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Note
Getting Started
Do not use manganese battery for this IC
recorder.
Step 1: Preparing a
Power Source
Clock setting display appears and the
year section flashes when you insert
battery for the first time, or when you
insert battery after the IC recorder has
been without battery for a certain period
of time. Please refer to step 3 in“Step 2:
Setting the Clock”on page 15 to set the
date and time.
Inserting the battery
1 Slide and lift the battery
compartment lid.
2 Insert one LR03 (size AAA) alkaline
battery with correct polarity, and
close the lid.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Recording STLP*5
mode
SP
*6
When replacing/charging
the battery
The remaining battery indicator on the
display shows the battery condition.
Recording Approx. 11 hr. Approx. 10 hr.
Playback*2
through
speaker
Approx. 14 hr. Approx. 14 hr.
30 min. 30 min.
Battery remain indication
Playback
using the
headphones
Approx. 32 hr. Approx. 32 hr.
: Replace the old battery with a new
one or charge the rechargeable
battery.
*7
Music file
(128 kbps/
44.1 kHz)
Recording LP
mode
: “LOW BATTERY“ appears and the IC
recorder will stop operation.
Battery life*1
When using Sony LR03 (SG) (size AAA)
alkaline battery
Recording Approx. 12 hr. –
Playback*2
through
speaker
Approx. 15 hr. Approx. 14 hr.
Recording ST*3
mode
Recording Approx. 9 hr. Approx. 9 hr.
30 min. 30 min.
STSP*4
Playback
Approx. 34 hr. Approx. 30 hr.
using the
headphones
(hr. : hours/min. : minutes)
Playback*2
through
speaker
Approx. 14 hr. Approx. 14 hr.
Playback
Approx. 30 hr. Approx. 30 hr.
using the
headphones
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
12
When using Sony NH-AAA rechargeable
battery
*7
Music file
(128 kbps/
44.1 kHz)
Recording LP
mode
Recording ST*3
mode
STSP*4
Recording Approx. 11 hr. –
Playback*2
through
speaker
Approx. 14 hr. Approx. 13 hr.
Recording Approx. 9 hr. Approx. 9 hr.
Playback*2
through
speaker
Approx. 13 hr. Approx. 13 hr.
Playback
using the
headphones
Approx. 31 hr. Approx. 28 hr.
30 min.
Playback
Approx. 28 hr. Approx. 28 hr.
using the
headphones
(hr. : hours/min. : minutes)
*1 The battery life may shorten depending on
how you operate the IC recorder.
*2 When playing back music through the internal
speaker with the volume level set to 22
*3 ST : Stereo high quality recording mode
*4 STSP : Stereo standard recording mode
*5 STLP : Stereo long play recording mode
*6 SP : Monaural standard play recording mode
*7 LP : Monaural long play recording mode
Recording STLP*5
mode
SP
*6
Recording Approx. 10 hr. Approx. 9 hr.
30 min.
Playback*2
through
speaker
Approx. 13 hr. Approx. 13 hr.
30 min. 30 min.
Playback
Approx. 30 hr. Approx. 30 hr.
using the
headphones
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Note while accessing
Step 2: Setting the
Clock
The IC recorder is accessing data when
an updating animation appears in
the display window or the operation
indicator flashes in orange or is lit in red.
While the IC recorder is accessing data,
do not remove the battery or connect
or disconnect the USB AC adaptor (not
supplied). Doing so may damage the
data.
Control key
(/)
Note
If the IC recorder is required to process a large
amount of data, an updating animation may
be displayed for an extended period of time.
This is not a malfunction of the IC recorder.
Wait until the animation disappears before
starting operation.
ENT
/MENU
You need to set the clock to use the
alarm function or record the date and
time.
Clock setting display appears when you
insert battery for the first time, or when
you insert a battery after the IC recorder
has been without battery for a certain
period of time. In this case, proceed from
step 3.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
1ꢁ
1 Select “DATE & TIME” in the menu.
3 Press the control key toward or
to set the year, month, day, hour,
and minute in sequence, and then
press ENT.
Press and hold /MENU for more
than one second.
The menu mode will be displayed in
the display window.
4 Press (stop) to return to the
Press the control key toward or to
select“DETAIL MENU,”and then press
ENT.
Press the control key toward or
to select“DATE & TIME,”and then press
ENT.
normal display.
Tip
Press /MENU to return to the previous
operation.
Note
2 Press the control key toward or
to select “07y1m1d,” and then press
ENT.
If you do not press ENT within one minute
of entering the clock setting data, the clock
setting mode is cancelled and the window will
return to the normal display.
To display the current date and
time
Press (stop) to display the current date
and time.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
1ꢂ
Basic Operations
Recording Messages
Built-in microphones
(headphone) jack
Operation indicator
2
3
1
1
2 Start recording.
1 Select a folder.
ꢀ
Press (record/pause) in the stop
mode.
ꢀ
Press /MENU to display the folder
selection window.
The operation indicator lights in red.
You do not need to press and hold
(record/pause) while recording.
The new message will be
ꢁ
Press the control key toward or to
select the folder in which you want to
record messages, and then press ENT.
automatically recorded after the last
recorded message.
ꢁ
Speak into the built-in microphone.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
1ꢃ
3 Press (stop) to stop recording.
To
pause
recording*
Do this
Press (record/pause).
During recording pause,
the operation indicator
flashes in red and“
flashes in the display
window.
The IC recorder stops at the beginning
of the current recording.
Tips
“
While recording you can lock all the
functions of all the buttons so that you can
prevent inadvertent operations by sliding
the HOLD switch in the direction of the
arrow.
release pause
and resume
recording
Press (record/pause)
again.
Recording resumes
from that point. (To stop
recording after pausing
recording, press (stop).)
Messages recorded using this IC recorder will
be recorded as MP3 files.
When you purchase the IC recorder, there
are 5 folders already available, and you can
record up to 99 messages in each folder.
review the
current
recording
instantly
Press .
Recording stops and
playback starts from the
beginning of the message
just recorded.
Notes
While the operation indicator is flashing or
is lit in red or orange, do not remove the
battery or connect or disconnect the USB AC
adaptor. Doing so may damage the data.
review during
recording
Press and hold
during recording
or recording pause.
Recording stops and you
can search backwards
while listening to fast
playback sound. After you
release , playback
starts from that point.
Noise may be recorded if an object, such
as your finger, etc., accidentally rubs or
scratches the IC recorder during recording.
Before making a recording, be sure to check
the remaining battery indicator (page 13).
To avoid replacing battery during a long
recording session, use a USB AC adaptor (not
supplied) (page 56).
The maximum recording time varies if you
record messages in mixed recording mode.
*
One hour after you pause recording,
recording pause is automatically released
and the IC recorder enters the stop mode.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
1ꢄ
Selecting the recording mode
Select the recording mode in the“REC
MODE”menu.
Monitoring the recording
Connect the supplied headphones to
the (headphone) jack and monitor the
recording. You can adjust the monitoring
volume by pressing the control key
toward VOL + or VOL –, but the recording
level is fixed.
ST :
High-quality stereo recording
mode (44.1 kHz/192 kbps)
You can record with stereo high-
quality sound.
STSP : Standard play stereo recording
mode (44.1 kHz/128 kbps)
You can record with stereo sound.
STLP : Long play stereo recording mode
(22.05 kHz/48 kbps)
Maximum recording time
The maximum recording time of all the
folders is as follows.
ICD-UXꢄ0
You can record for a longer time
with stereo sound.
Standard play monaural
recording mode (44.1 kHz/
32 kbps)
ST mode
STSP mode STLP mode
12 hr. 5 min. 18 hr. 5 min. 48 hr. 20 min.
SP :
LP :
SP mode LP mode
72 hr. 30 min. 290 hr. 10 min.
You can record with standard
quality sound.
Long play monaural recording
mode (11.025 kHz/8 kbps)
You can record for a longer time
with monaural sound.
ICD-UXꢅ0
ST mode
STSP mode STLP mode
24 hr. 10 min. 36 hr. 20 min. 96 hr. 50 min.
SP mode
145 hr. 20 min. 581 hr. 20 min.
(hr. : hours/min. : minutes)
LP mode
To record with better sound quality,
select the ST or STSP mode.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
1ꢅ
The recording starts when the IC
recorder detects sound. The recording
pauses when no sound is detected
Various Recording Modes
Starting to Record
Automatically in
Response to Sound
– the VOR Function
and“
”and“
”flash. When the
IC recorder detects sound again, the
recording starts again.
To cancel the VOR function
Set“VOR”to“OFF”in the menu.
Notes
The VOR function is affected by the sound
around you. Set“MIC SENS”in the menu
according to the recording conditions. If
recording is not satisfactory after you have
changed the microphone sensitivity, or for
an important recording, set“VOR”to“OFF”in
the menu.
2
1
If you press (record/pause) to pause
recording when“VOR”is set to“ON”in the
menu, only“
”flashes.
1 Press the control key toward or
to set “VOR” to “ON” in the menu,
and then press ENT.
2 Press (record/pause).
“
”and“
”appear in the
display window.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
1ꢆ
2 Press the control key toward or
to select “MIC IN,” and then press
ENT.
Recording with an
External Microphone
3 Speak into the external microphone
and start recording.
Stereo
microphone
The built-in microphone is
automatically cut off.
If the input level is not strong enough,
adjust the microphone sensitivity on
the IC recorder.
When a plug in power type
microphone is connected, power
is automatically supplied to the
microphone from the IC recorder.
Recommended microphones
You can use the Sony ECM-CS10 or ECM-CZ10
electret condenser microphone (not supplied).
1 Connect an external microphone to
the (microphone) jack when the
IC recorder is in the stop mode.
“SELECT INPUT”appears in the display
window.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
20
2 Press the control key toward or
to select “AUDIO IN,” and then press
ENT.
Recording from Other
Equipment
3 Start recording.
The built-in microphone is
automatically cut off and the sound
from the connected equipment is
recorded.
Tape
recorder, etc.
Notes
When recording from other equipment, the
microphone sensitivity cannot be adjusted.
If the input level is not strong enough,
connect the headphone jack (minijack,
stereo) of other equipment to the
(microphone) jack of the IC recorder and
adjust the volume level on the equipment
connected to the IC recorder.
1 Connect other equipment to the IC
recorder when the IC recorder is in
the stop mode.
Connect the audio output connector
(stereo mini-plug) of other equipment
to the (microphone) jack of the IC
recorder using an audio connecting
cable*.
“SELECT INPUT”appears in the display
window.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
21
* Optional audio connecting cables (not
supplied)
Recording sound from a
telephone or a cell phone
You can use the ECM-TL1 headphone-
type electret condenser microphone
(not supplied) to record sound from a
telephone or a cell phone.
For details on how to make the
connection, see the operating
instructions supplied with the ECM-TL1
microphone.
To the IC
recorder
To the other
equipment
RK-G139 HG Stereo
Mini-plug
(monaural)
(without
mini-plug
(without
resistor)
resistor)
RK-G136 HG Stereo
Stereo
mini-plug
(without
resistor)
mini-plug
(without
resistor)
Notes
Note
After you have made the connection, check
the sound quality of the conversation
and the recording level before you start
recording.
Your dealer may not handle some of the above
listed optional accessories. Please ask the
dealer for detailed information.
If the beep of the telephone or a dial tone is
recorded, the conversation may be recorded
with lower level of sound. In this case, start
recording after the conversation has started.
The VOR function may not work, depending
on the kind of telephone used or the line
condition.
We assume no responsibility whatsoever
for any inconvenience, even if you cannot
record a conversation using the IC recorder.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Playback/Erasing
Playing Back
Messages
(headphone) jack
Operation indicator
4
5
1
1
3
DPC
A-B
2
3 Press to start playback.
1 Select a folder.
The operation indicator lights in green.
(When“LED”is set to“OFF”in the menu
(page 38), the operation indicator does
not light.)
Press /MENU.
Press the control key toward or to
select the folder, and then press ENT.
2 Press or to select the
4 Press the control key toward VOL +
message you want to play.
or VOL – to adjust the volume.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2ꢀ
Quickly locating the point you
wish to start playback (Easy
Search)
When“EASY SEARCH”is set to“ON”
(page 37) in the menu, you can quickly
locate the point at which you wish to
start playback by pressing or
repeatedly during playback.
You can go back approx. 3 seconds by
pressing once, or advance approx.
10 seconds by pressing once. This
function is useful for locating a desired
point in a long recording.
5 Press (stop) to stop playback.
After playing back the last message
in the selected folder, the IC recorder
stops at the beginning of that
message.
Tip
During playback you can lock all the functions
of all the buttons so that you can prevent
inadvertent operations by sliding the HOLD
switch in the direction of the arrow.
Listening with better sound
quality
To listen with the headphones :
Connect the supplied headphones
to the (headphone) jack. The
built-in speaker will be automatically
disconnected.
To listen from an external speaker:
Connect an active or passive speaker
(not supplied) to the (headphone)
jack.
Searching forward/backward
during playback (Cue/Review)
To search forward (Cue): Press and
hold during playback and release
it at the point you wish to resume
playback.
To search backward (Review): Press
and hold during playback and
release it at the point you wish to
resume playback.
The IC recorder searches at slow speed
with playback sound. This is useful to
check one word forward or back. Then,
if you press and hold the button, the IC
recorder starts to search at higher speed.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2ꢁ
When messages are played back
To
Do this
to the end of the last message
stop at the
current position To resume playback from
(Playback Pause that point, press
function)
Press (stop) or .
When you play back or fast play back to the
end of the last message, “MESSAGE END”
lights up for 5 seconds and the operation
indicator lights up in green. (You cannot
hear the playback sound.)
When“MESSAGE END”and the operation
indicator go off, the IC recorder will stop at
the beginning of the last message.
If you press and hold while“MESSAGE
END”is lit, the messages are played back
rapidly, and normal playback will start at the
point you release the button.
If the last message is long and you wish to
start playback at a later part of the message,
press and hold to go to the end of
the message and then press while
“MESSAGE END”is lit to go back to the
desired point.
again.
go back to the Press once.*
beginning of
the current
message
go back to
previous
messages
Press repeatedly.
(During stop mode, keep
the button pressed to
go back the messages
continuously.)
skip to the next Press once.*
message
skip to the
succeeding
messages
Press repeatedly.
(During stop mode,
keep the button pressed
to skip the messages
continuously.)
For messages other than the last one, go to
the beginning of the next message and play
backward to the desired point.
* These operations are for when“EASY
SEARCH”is set to“OFF”(page 37).
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2ꢂ
Various playback modes
Adjusting the playback
speed – DPC (the Digital
Pitch Control function)
When you slide the DPC switch to“ON,”
you can adjust the playback speed
between +100% and –50% of normal
speed in the menu.
You can select“1 FILE”playback (one
message/file is played back once),
“FOLDER”playback (all the messages/files
in the selected folder are played back
continuously), “ALL”playback (all the
recorded messages/files are played back
continuously) in the“PLAY MODE”menu
(page 38).
The message is played back in natural
tones thanks to the digital processing
function.
Playing back a message
repeatedly
During playback, press and hold
until“ 1”appears. The selected message
will be played back repeatedly.
To resume normal playback, press
again.
1 Slide the DPC switch to “ON.”
2 Adjust the playback speed in the
“DPC” menu (page 36).
To resume normal playback
Slide the DPC switch to“OFF.”
Playback with“EFFECT”
Set“EFFECT”to the setting you want in
the menu (page 37). However, when you
play back using the built-in speaker, the
setting is invalid.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2ꢃ
Playing back a specified
section repeatedly – A-B
Repeat
Playing Back a
Message at a Desired
Time with an Alarm
1 During playback, press (repeat)
You can sound an alarm and start
playback of a selected message at a
desired time.
A-B to specify the starting point A.
“A-B B?”is displayed.
You can have the message played back
on a specified date, once every week, or
at the same time every day.
2 Press (repeat) A-B again to
specify the finishing point B.
“
A-B”is displayed and the specified
1 Select the message you want to
section is played back repeatedly.
play back with an alarm.
To resume normal playback
Press .
2 Enter the alarm setting mode.
Select“ALARM”in the menu and press
ENT.
To stop A-B Repeat playback
Press (stop).
Press the control key toward or to
select“ON,”and then press ENT.
To change the segment specified
for A-B Repeat playback
During A-B Repeat playback, press A-B
again to specify a new starting point A.
Then specify a new finishing point B, as
in step 2.
Note
You cannot specify the finishing point B before
the starting point A that has been set.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2ꢄ
To listen to the same message
again
Press , and the same message will
3 Set the alarm date and time.
Press the control key toward or
to select“DATE,”a day of the week, or
“DAILY,”and then press ENT.
be played back from the beginning.
When you select “DATE”:
To stop the alarm before the
playback starts
Press (stop) while the alarm sound is
heard. You can stop the alarm playback
even when the HOLD function is
activated.
Set the year, month, day, hour, and
minute in sequence, as described in
“Step 2: Setting the Clock”on page 14,
then press ENT.
When you select a day of the week
or “DAILY”:
Press the control key toward or to
set the hour and then press ENT, press
the control key toward or to set
the minute and then press ENT.
To change the alarm setting
Start from step 2 on page 27.
The setting process is finished and“”
(alarm indicator) appears in the display
window.
To cancel the alarm setting
Follow steps 1 and 2- on page 27. In
step 2- , press the control key toward
or to select“OFF,”and press ENT. The
alarm will be cancelled and the alarm
indicator will disappear from the display
window.
When the set date and time
comes
At the set time, the alarm will sound
for about 10 seconds while“ALARM”is
displayed in the display window and the
selected message will be played back.
When the playback ends, the IC recorder
will stop automatically at the beginning
of that message.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2ꢅ
Notes
Erasing Messages
You can set only one alarm.
When the clock has not been set or no
messages are recorded, you cannot set the
alarm.
The alarm sounds even if you set“BEEP”to
“OFF”in the menu (page 38).
If the alarm time comes during recording,
the alarm will sound after the recording is
finished. “”will flash when the alarm time
comes.
When the alarm time comes when the IC
recorder is in the menu mode, the alarm
will sound and the menu mode will be
cancelled.
3, 4
2
The alarm set for“DATE”will be cancelled
when the alarm playback finishes.
If you delete a message on which you
have set an alarm, that alarm will be also
cancelled.
You can erase the recorded messages
one by one or all messages in a folder at
a time.
Note
Once a recording has been erased, you cannot
retrieve it.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2ꢆ
Erasing messages one by
one
Erasing all messages in a
folder
You can erase unwanted messages,
retaining all other messages when the IC
recorder is in the stop or playback mode.
When a message is erased, the
1 Select the folder containing the
messages you want to erase when
the IC recorder is in the stop mode.
remaining messages will advance and
be renumbered so that there will be no
space between messages.
2 Press and hold /MENU for more
than one second to enter the menu
mode.
The menu mode window will be
displayed.
1 Select the message you want to
erase.
3 Press the control key toward or
to select “ERASE ALL,” and then
press ENT.
2 Press and hold /MENU for more
than one second to enter the menu
mode.
The menu mode window will be
displayed.
4 Press the control key toward or
to select “EXECUTE,” and then press
ENT.
3 Press the control key toward or
to select “ERASE A FILE,” and then
press ENT.
“ERASING …”appears in the display
window and all messages in the
selected folder will be erased.
The message to be erased will be
played back.
4 Press the control key toward or
to select “EXECUTE,” and then press
ENT.
“ERASING …”appears in the display
window and the selected message will
be erased.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ0
“EXECUTING…”is displayed and the
message is moved to the last position
in the destination folder.
When you move a message to another
folder, the original message in the
previous folder will be deleted.
Editing Messages
Moving Message to a
Different Folder
Note
When“ ”is displayed for the folder indicator,
you cannot move a message (page 47).
To cancel moving the message
Press (stop) before step 4.
1 Select the message you want to
move.
2 Press and hold /MENU for more
than one second to enter the menu
mode.
The menu mode window will be
displayed.
3 Press the control key toward or
to select “MOVE,” and then press
ENT.
The message to be moved will be
played back.
4 Press the control key toward or
to select the folder that you want to
move the message into, and then
press ENT.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ1
Utilizing the Menu Function
3 Press the control key toward or
to select the setting that you want
to set, and then press ENT.
Making Settings for
the Menu
4 Press (stop) to exit the menu
mode.
Note
If you do not press any button for one minute,
the menu mode is automatically cancelled and
the window will return to the normal display.
4
To return to the previous window
2, 3
2, 3
1
Press /MENU during menu mode.
1 Press and hold /MENU for more
than one second to enter the menu
mode.
The menu mode window will be
displayed.
2 Press the control key toward or
to select the menu item for which
you want to make setting, and then
press ENT.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ2
Menu settings
Menu items
Settings
Operation mode
( : the setting �an �e made/
: the setting �annot �e made)
Stop
mode
Play�a�k
mode
Re�ording
mode
REC MODE
MIC SENS
VOR
ST, STSP, STLP, SP, LP
HIGH (H), LOW (L)
ON, OFF
DISPLAY
DPC
ELAPSE, REMAIN, REC DATE, REC TIME
n% (n=–50 - +100)
POP, ROCK, JAZZ, BASS1, BASS2, OFF
ON, OFF
EFFECT
EASY SEARCH
PLAY MODE
BEEP
1 FILE, FOLDER, ALL
ON, OFF
LED
ON, OFF
BACKLIGHT
MOVE
ON, OFF
(Folder to be moved)
ON, OFF
ALARM
ERASE ALL
ERASE A FILE
EXECUTE, CANCEL
EXECUTE, CANCEL
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢀ
Menu items
Settings
Operation mode
( : the setting �an �e made/
: the setting �annot �e made)
Stop
mode
Play�a�k
mode
Re�ording
mode
DETAIL MENU
SELECT INPUT MIC IN, AUDIO IN
DATE&TIME
FORMAT
_ _ y _ _ m _ _ d _ _ : _ _
EXECUTE, CANCEL
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢁ
Menu items
Settings (*: Initial setting)
REC MODE
Sets the recording mode.
ST:
Stereo high-quality recording mode.
STSP*:
Stereo standard recording mode.
STLP:
Stereo long play recording mode.
SP:
Monaural standard play recording mode.
LP:
Monaural long play recording mode.
MIC SENS
VOR
Sets the microphone sensitivity.
HIGH (H)*:
To record at meeting or in a quiet and/or spacious place.
LOW (L):
To record dictation, or record in a noisy place.
Sets the VOR (Voice Operated Recording) function.
ON:
Recording starts when the IC recorder detects sound and pauses
when no sound is heard, eliminating recording during soundless
periods.The VOR function is activated when (record/pause) is
pressed.
OFF*:
The VOR function does not work.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢂ
Menu items
Settings (*: Initial setting)
DISPLAY
Changes the display mode.
ELAPSE*:
Elapsed playback time of one message
REMAIN:
During playback, the remaining time of the message
When stopped and during recording, the available recording time
REC DATE:
Date recorded
REC TIME:
Time recorded
DPC
Sets the DPC (Digital Pitch Control) function.
When you set the DPC switch to“ON,”you can adjust the speed of the
playback in a range from +100% to –50%. Set the speed by 10% for +
setting and by 5% for – setting.
–30%*
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢃ
Menu items
Settings (*: Initial setting)
EFFECT
POP:
Stresses middle ranges, ideal for vocals.
ROCK:
Emphasizes high and low ranges for a powerful sound.
JAZZ:
Emphasizes high ranges for a lively sound.
BASS1:
The bass sound is emphasized.
BASS2:
The bass sound is emphasized even more.
OFF*:
The EFFECT function does not work.
Note
When playing back messages using a built-in speaker, the EFFECT function
does not work.
EASY SEARCH
Sets the easy search function.
ON:
You can go forward for about 10 seconds by pressing and go
back for about 3 seconds by pressing . This function is useful
when attempting to locate desired point in a long recording.
OFF*:
The easy search function does not work. When you press or
, a message will be moved forward or backward.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢄ
Menu items
Settings (*: Initial setting)
PLAY MODE
Sets the playback mode.
1 FILE:
When a message is played back, the IC recorder stops at the
beginning of the next message.
FOLDER*:
Messages in one folder are played back continuously.
ALL:
All messages are played back continuously.
BEEP
LED
Sets whether a beep will be heard or not.
ON*:
A beep will sound to indicate that an operation has been accepted.
OFF:
No beep sound will be heard.
Note
The alarm sounds even if you set“BEEP”to“OFF”in the menu.
Turns the operation indicator on or off during operation.
ON*:
During recording or playback, the operation indicator lights or
flashes.
OFF:
The operation indicator does not light or flash, even during
operation.
Note
When the IC recorder is connected to a computer, the operation indicator
lights or flashes even if“LED”is set to“OFF.”
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢅ
Menu items
Settings (*: Initial setting)
BACKLIGHT
Turns the backlight in the display window on or off.
ON*:
The backlight in the display window lights up for 10 seconds.
OFF:
The backlight in the display window does not light, even during
operation.
MOVE
The selected message will be moved to the selected folder (page 31).
Before attempting to move a message, select the message to be moved
and then go to the menu window.
ALARM
Sets the alarm (page 27).
ON:
To set the alarm, select“ON”and set the date, time or day of the week
or choose daily for playback.
OFF*:
The alarm is cancelled.
ERASE ALL
All messages in the selected folder will be erased (page 30).
Press /MENU to return to the folder window before erasing the
messages and select a folder from which all messages are to be erased,
and then go to the menu window and select“EXECUTE.”
ERASE A FILE
The selected message will be erased (page 30).
Before erasing the message, select a message to be erased, and then go
to the menu window and select“EXECUTE.”
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢆ
Menu items
Settings (*: Initial setting)
DETAIL MENU
SELECT INPUT Selects the external input to be recorded that is connected to the
(microphone) jack.
MIC IN*:
Select when you record messages using an external microphone.
AUDIO IN:
Select when you record using other equipment.
DATE & TIME Sets the clock by setting year, month, day, hour, and minute in
sequence (page 14).
FORMAT
Sets the formatting of the drive.
EXECUTE:
“FORMATTING …”appears and the drive will be formatted.
CANCEL*:
The drive will not be formatted.
Notes
Use the IC recorder formatting function to format the memory.
When the memory is formatted, all the data stored in the IC recorder will
be erased. Once the memory has been erased, you cannot retrieve the
data that was erased.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁ0
Hardware environment:
– Port: USB port
Utilizing �our �o�puter
Using the IC Recorder
with Your Computer
– Sound board: Sound cards
compatible with any of the supported
operating systems
System requirements
Note
The following systems are not supported:
Operating systems other than the ones
indicated on the left
Personally constructed computers or
operating systems
Upgraded operating systems
Multi-boot environment
Multi-monitor environment
Operating systems:
Windows Vista® Home Basic
Windows Vista® Home Premium
Windows Vista® Business
Windows Vista® Ultimate
Windows® XP Home Edition Service Pack
2 or higher
Windows® XP Professional Service Pack 2
or higher
Windows® XP Media Center Edition
Service Pack 2 or higher
When you are using Windows®
2000 Professional
Install the driver using“SonyRecorder_
Driver.exe”in the IC recorder.
Windows® XP Media Center Edition 2004
Service Pack 2 or higher
Windows® XP Media Center Edition 2005
Service Pack 2 or higher
Windows® 2000 Professional Service Pack
4 or higher
Mac OS X (v10.2.8-v10.5)
Pre-Installed
Note
64 bit OS is not supported.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁ1
Tip
Connecting the IC recorder
to your computer
You can transfer the IC recorder data
onto your computer by connecting the
IC recorder to the computer.
If the IC recorder cannot be connected to the
USB connector of your computer directly, use
the supplied USB connection support cable.
Remove the USB cap from the IC recorder
and then connect the IC recorder to the
USB connector of your computer.
The IC recorder is recognized by the
computer as soon as the connection is
made. While the IC recorder is connected
to the computer, “CONNECTING”is
displayed in the display window of the
IC recorder.
USB connection
support cable
(supplied)
Computer
IC recorder
To USB connector
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁ2
Notes
Using Voice
If you connect more than two USB devices
to your computer, normal operation will not
be guaranteed.
Recognition Software
Use of this IC recorder with a USB hub or a
USB connection support cable other than
the supplied cable is not guaranteed.
A malfunction may occur depending on the
USB devices connected at the same time.
When voice recognition software (not
supplied) is installed on your computer,
you can transcribe a message into a text
file.
Before connecting the IC recorder to the
computer, make sure that the battery is
inserted in the IC recorder.
It is recommended that you disconnect the
IC recorder from the computer when you are
not using the IC recorder connected to the
computer.
Introducing the voice
recognition software
Dragon NaturallySpeaking is a speech-
recognition software application that
allows you to recognize and transcribe
your recorded voice in a message and
convert it into a text file.
For details on Dragon NaturallySpeaking,
refer to the operating instructions
supplied with Dragon NaturallySpeaking.
For information on using Dragon
NaturallySpeaking, refer to the
Disconnecting the IC
recorder from your
computer
Follow the procedures below; otherwise,
data may be damaged.
documentation supplied with the
software. For the latest version and
information on the availability of Dragon
NaturallySpeaking in each region, please
refer to the following home page:
1 Make sure that the operation
indicator is not flashing.
2 Disconnect the IC recorder from the
USB connector of the computer.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁꢀ
Notes
Creating a user file adapted
to your recorded speech
(Training)
You can use the transcribing feature
only when you have installed Dragon
NaturallySpeaking Select or Professional
Edition (not supplied) on your computer.
To install Dragon NaturallySpeaking, your
computer should meet the specified system
requirements.
What is“Training”?
Before you can transcribe
You can transcribe the following messages
saved in your IC recorder or on your
computer;
ST, STSP, STLP or SP recording mode
messages (MP3 files)
44.1/16/11 kHz 16-bit WAV files saved on
your computer
You cannot transcribe a message recording
the voices of more than one person.
recorded messages using Dragon
NaturallySpeaking, you must create a
user file specifically adapted to the sound
of your recorded speech. This procedure
is called“training.”
When training is complete, Dragon
NaturallySpeaking creates a user speech
file containing information about your
recorded speech.
Refer to the operating instructions
or the help supplied with Dragon
NaturallySpeaking, as some parts of
training are the same as those required
for dictating directly to the computer
using a headset microphone.
Even if you have already created a user
speech file with a headset microphone,
you should create a separate speech
file for the IC recorder to get better
recognition accuracy.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁꢁ
Tips on using the IC recorder
Playing Back
When transcribing messages recorded
using the IC recorder, the following
tips will help you obtain maximum
recognition accuracy.
Transferred MP3 Files
Using the IC Recorder
You can play back MP3 files on your
computer using the IC recorder.
The maximum playback time (tracks*),
when playing MP3 files using the IC
recorder, is as follows.
Set “REC MODE” to “ST,”“STSP,”
“STLP” or “SP” in the menu.
When creating a user speech file
(training), set“REC MODE”to the mode
you normally use for voice recognition
software.
48 kbps
48 hr. 20 min. 18 hr. 5 min.
(725 tracks) (271 tracks)
128 kbps
Set “MIC SENS” to “LOW (L)” in the
menu.
Hold the IC recorder firmly and
start recording.
ICD-UX70
ICD-UX80
96 hr. 50 min. 36 hr. 20 min.
(1452 tracks) (545 tracks)
Hold the IC recorder so that the
microphone is about an inch (2 - 3 cm)
from the corner of your mouth, not
directly in front of it. This minimizes the
sound of your breath in the recordings,
enabling maximum recognition
accuracy.
(hr. : hours/min. : minutes)
* In the case where tracks of 4 minutes each
are transferred to the IC recorder.
Note
Avoid recording in a noisy place, such as on a
subway platform, in order to obtain maximum
recognition accuracy.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁꢂ
1 Connect the IC recorder to your
6 Press (stop) to stop playback.
To copy MPꢀ files (Drag and drop)
computer (page 42).
On the Windows screen; open“My
Computer”and make sure that
“IC RECORDER”has been newly
recognized.
On the Macintosh screen; make sure
that a“IC RECORDER”drive is displayed
on the desk top.
2 Copy the folder in which the MP3
Click and hold,
drag,
and then drop.
files are stored to the IC recorder.
On the Windows screen using Explorer,
and on the Macintosh screen using
Finder, drag and drop the folder onto
the IC recorder.
The IC recorder can recognize up to
500 folders. You can copy up to 999
files to one folder and up to 5000 files
in total.
3 Remove the IC recorder from your
computer, press /MENU, press the
control key toward or to select
the folder you want, and then press
ENT.
4 Press or to select the file
you want to play.
5 Press to start playback.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁꢃ
Construction of folders and
files
The folders and files are displayed on the
computer screen as shown.
“IC RECORDER”
Recordable folder
VOICE
The folder indicators in the display
window of the IC recorder are as follows:
:Folder in which you can record using
the IC recorder (They have been
already made when you purchase the
IC recorder.)
FOLDER01
FOLDER05
:Playback only folders (They are
displayed when MP3 files have
been transferred to them using a
computer.)
Playback only folder
Folder 1
*1
Note
You can record messages in up to 5 folders
using the IC recorder.
Folder 2
Folder 3
Folder 4
*2
*3
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁꢄ
*1 The name of a folder in which MP3 files are
stored will be displayed on the IC recorder as
it is, so it is convenient if you put an easy-to-
remember name on the folder in advance.
Using the IC Recorder
as a USB Mass Storage
Device
*2 The IC recorder can recognize up to three
levels of folders copied to the IC recorder,
that is, up to Folder 4 shown in the figure.
When the IC recorder is connected to
your computer directly or using a USB
connection support cable, image data
or text data on the computer, as well as
messages or files recorded using the IC
recorder can be temporarily stored in the
IC recorder.
*3 If you copy MP3 files separately, they are
classified as being in“NO FOLDER.”
Tips
You can enter title name or artist name, etc.,
into MP3 files as ID3 tag information. The ID3
tag information can be displayed on the IC
recorder. It is useful if you input the ID3 tag
information using the software you use to
make the MP3 files on your computer.
Your computer must meet the
operating system requirements and port
environment described on page 41 to
use the IC recorder as a USB mass storage
device.
You can display the ID3 tag information in
sequence by pressing the control key toward
or .
Notes
You cannot copy 511 or more folders (except
VOICE folders) or files to the root directory
that is located immediately below“IC
RECORDER”on the computer. This is due to
Windows system limitations.
If no title name or artist name has been
entered into the ID3 tag information,
“Unknown”will be displayed.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁꢅ
Troubleshooting
Troubleshooting
Before taking the IC recorder for repair, check the following sections. Should any
problem persist after you have made these checks, consult your nearest Sony dealer.
Symptom
Remedy
The IC recorder cannot be The HOLD switch is set. Slide the HOLD switch in the direction
turned on.
opposite that of the arrow.
The IC recorder does not
operate.
The battery has been inserted with incorrect polarity (page 11).
The battery is weak (page 12).
The buttons are locked with the HOLD switch (page 8).
No sound comes from the The volume is turned down completely (page 23).
speaker.
Headphones are plugged in (page 24).
Sound comes from the
speaker even when the
headphones are plugged
in.
If you plug in the headphones not securely during playback,
the sound may come from the speaker. Unplug the
headphones and then insert them securely.
The operation indicator
does not light.
“LED”is set to“OFF”(page 38). Display the menu and set“LED”
to“ON”.
“MEMORY FULL”is
displayed and you cannot
start recording.
The memory is full. Erase some of the messages (page 29) or
erase all the messages after you store them on your computer.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁꢆ
Symptom
Remedy
“FILE FULL”is displayed
and you cannot operate
the IC recorder.
99 messages have been recorded in the selected
folder or
495 messages (when there are 5 folders) in total have been
recorded. Therefore you cannot record another message, or
move a message. Erase some of the messages (page 29) or
erase all the messages after you store them on your computer.
Recording is interrupted.
Noise is heard.
The VOR function (page 19) is activated. Set“VOR”to“OFF”in
the menu (page 35).
An object, such as your finger, etc., accidentally rubbed or
scratched the IC recorder during recording so that noise was
recorded.
The IC recorder was placed near an AC power source, a
fluorescent lamp or a mobile phone during recording or
playback.
Plug of the connected microphone was dirty when recording.
Clean the plug.
The (headphones) plug is dirty. Clean the plug.
Recording level is low.
“MIC SENS”(microphone sensitivity) is set to“LOW (L)”.
Display the menu and set“MIC SENS”to“HIGH (H)”(page 35).
When recording from
other equipment, the
input level is too strong or
not strong enough.
Connect the headphone jack of other equipment to the
(microphone) jack of the IC recorder and adjust the volume
level on the equipment connected to the IC recorder.
Playback speed is too fast The playback speed is adjusted in DPC. Slide the DPC switch to
or too slow.
“OFF”or display the menu and adjust the speed in DPC again
(pages 26, 36).
“--:--”is displayed.
You have not set the clock (page 14).
“--y--m--d”or ”--:--”is
displayed on the REC
DATE display.
The date of recording will not be displayed if you recorded the
message when the clock was not set.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢂ0
Symptom
Remedy
There are fewer menu
items displayed in the
menu mode.
The menu items displayed are different depending on the
operation modes (stop mode, playback mode, and recording
mode) (pages 33, 34).
The battery life is short.
The battery life on pages 12 and 13 is based on playback with
the volume level set to 22 (using Sony alkaline battery LR03
(SG)). The battery life may shorten depending on the operation
of the IC recorder.
There is no battery power Even if you do not use the IC recorder, the battery is consumed
remaining after you have
left the battery inserted
for long time without
using the IC recorder.
slightly. The battery life in this case varies depending on
humidity or other environmental conditions. Usually, the
battery lasts about four months. If you do not intend to use the
IC recorder for an extended period of time, it is recommended
that you remove the battery.
The changed menu
setting does not function.
If the battery is removed just after the menu setting is
changed, the menu setting may not function.
It takes a long time for the If the IC recorder is required to process a large amount of
IC recorder to start.
data, it may take longer for the IC recorder to start. This is not
a malfunction of the IC recorder. Wait until the start-up display
disappears.
The IC recorder does not
operate correctly.
Take out the battery and insert it again (page 11).
The IC recorder does not
operate.
You may have formatted the memory of the IC recorder using
the computer. Use the IC recorder formatting function to
format the memory (page 40).
Please note that recorded messages may be erased during service or repair work.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ1
Error messages
Error message
Cause/Remedy
BATTERY LOW
You cannot format the memory or erase all the files in a folder
because of insufficient battery power. Prepare a new battery to
replace the current one.
LOW BATTERY
Battery is exhausted. Replace the old battery with a new
one. Or charge the rechargeable battery or replace the old
rechargeable battery with a new one.
MEMORY FULL
FILE FULL
The remaining memory capacity of the IC recorder is
insufficient. Erase some messages before recording.
When there are already 99 messages in the selected folder or
the total number of the file stored in the IC recorder becomes
maximum, you cannot record a new message. Erase some
messages before recording a message.
FILE DAMAGED
FORMAT ERROR
You cannot play or edit messages, because the data of the
selected file is damaged.
The IC recorder cannot be turned on using the computer
because there is no copy of the control file required for
operation. Format the IC recorder using the formatting
function in the menu.
PROCESS ERROR
The IC recorder failed in memory access. Remove and then
re-insert the battery.
Save a backup copy of your data and format the IC recorder
using the menu.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢂ2
Error message
SET DATE&TIME
NO FILE
Cause/Remedy
Set the clock; otherwise, you cannot set the alarm.
The selected folder does not have any messages. You cannot
move a message or set the alarm, etc., because of this.
PAST DATE/TIME
FILE PROTECTED
You set the alarm when the time has already passed. Check it
and set the appropriate date and time.
The selected message is protected and is now a“Reading
only”file. You cannot erase it. Cancel“Reading only”on your
computer to edit the message using the IC recorder.
UNKNOWN DATA
CANNOT OPERATE
The data does not have a file format which the IC recorder
supports.
You cannot move a message, because there is more than one
folder that has files with same name. Change the file names.
A message in the
folder cannot be moved.
CHANGE FOLDER
SYSTEM ERROR
If there are no MP3 files in the
displayed in the display window, therefore, the folder setting
will be changed.
folder, no folders are
A system error other than the above has occurred. Remove the
battery and re-insert it.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢂꢀ
System limitations
There are some system limitations of the IC recorder. Troubles as mentioned below are
not malfunctions of the IC recorder.
Symptom
Cause/Remedy
You cannot record
messages up to the
maximum recording time.
If you record messages in a mixture of ST, STSP, STLP, SP and LP
modes, the recordable time varies from the maximum ST mode
recording time to the maximum LP mode recording time.
The sum of the number on the counter (elapsed recording
time) and the remaining recording time may be less than the
IC recorder’s maximum recording time.
You cannot display MP3
files in order.
If you have transferred MP3 files using your computer, those
files may not be copied in order of transfer because of the
System limitation.
You cannot enter lower-
case characters.
Depending on the combination of the characters used for
the folder name that was made on your computer, those
characters may change to all capitals.
You cannot specify the
finishing point B.
You cannot specify the finishing point B before the starting
point A that has been set.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢂꢁ
* Optional audio connecting cables (not
supplied)
Additional Infor�ation
To the IC
recorder
To the other
equipment
Recording with Other
Equipment
RK-G139 HG Stereo
Mini-plug
(monaural)
(without
mini-plug
(without
resistor)
To audio input
Tape
connector
resistor)
recorder, etc.
RK-G136 HG Stereo
Stereo
mini-plug
(without
resistor)
mini-plug
(without
resistor)
To
(headphone)
jack
Note
Your dealer may not handle some of the above
listed optional accessories. Please ask the
dealer for detailed information.
To record the sound of the IC recorder
with other equipment, connect the
(headphone) jack of the IC recorder to
the audio input connector (minijack,
stereo) of other equipment using an
audio connecting cable*.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢂꢂ
1 Remove the USB cap from the
IC recorder and connect the IC
recorder to a USB AC adaptor (not
supplied) .
Using a USB AC
Adaptor (not
supplied)
2 Connect the USB AC adaptor to an
AC outlet.
USB connector of the
IC recorder
Disconnecting the IC
recorder from the AC outlet
Follow the procedures below; otherwise,
data may be damaged.
USB AC adaptor
(not supplied)
1 If you are recording or playing back
a message, press (stop) to put the
IC recorder into the stop mode.
2 Make sure that the operation
indicator is not flashing.
You can connect the IC recorder to an AC
outlet using a USB AC adaptor AC-U50A/
AC-U50AD (not supplied).
3 Disconnect the USB AC adaptor
from the AC outlet, and then
disconnect the IC recorder from the
USB AC adaptor.
Note
Your dealer may not handle some of the above
listed optional accessories. Please ask the
dealer for detailed information.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢂꢃ
Notes
Precautions
On power
During recording (the operation indicator
lights or flashes in red) or accessing data (the
operation indicator flashes in orange),
the IC recorder should not be connected
to or disconnected from the USB AC
adaptor connected to the AC outlet.
the USB AC adaptor connected to the IC
recorder should not be connected to or
disconnected from the AC outlet.
Doing so may damage the data. If the
IC recorder is required to process a large
amount of data, the start-up window may
be displayed for an extended period of time.
This is not a malfunction of the IC recorder.
Wait until the start-up display disappears
from the display window.
Operate the unit only on 1.5 V or 1.2 V
DC. Use one LR03 (size AAA) alkaline
battery or one NH-AAA rechargeable
battery.
On safety
Do not operate the unit while driving,
cycling or operating any motorized
vehicle.
On handling
Do not leave the unit in a location
near heat sources, or in a place subject
to direct sunlight, excessive dust or
mechanical shock.
Should any solid object or liquid fall
into the unit, remove the battery and
have the unit checked by qualified
personnel before operating it any
further.
While a USB AC adaptor (not supplied) is
being used, the remaining battery indicator
does not appear in the display window.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢂꢄ
On noise
Specifications
Capacity (User available capacity)
Noise may be heard when the unit
is placed near an AC power source, a
fluorescent lamp or a mobile phone
during recording or playback.
ICD-UX70:
1 GB (approx. 996 MB =1,044,611,072 Byte)
ICD-UX80:
2 GB (approx. 1.94 GB =2,093,056,000 Byte)
A part of the memory capacity is used as a
management area.
Noise may be recorded when an
object, such as your finger, etc., rubs or
scratches the unit during recording.
Recording time*1
See page 18.
On maintenance
To clean the exterior, use a soft cloth
slightly moistened in water. Do not use
alcohol, benzine or thinner.
Frequency range
ST : 40 Hz - 20,000 Hz
STSP : 40 Hz - 15,000 Hz
STLP : 60 Hz - 7,500 Hz
SP : 60 Hz - 10,000 Hz
LP : 60 Hz - 3,400 Hz
If you have any questions or problems
concerning your unit, please consult your
nearest Sony dealer.
Bit rates and sampling frequencies for
MP3 files
Backup recommendations
Bit rate: 32 - 320 kbps*2, VBR
Sampling frequencies*3: 16/22.05/24/32/44.1
/48 kHz
To avoid potential risk of data loss
caused by accidental operation or
malfunction of the IC recorder, we
recommend that you save a backup
copy of your recorded messages on a
tape recorder or to a computer, etc.
*1 When you are going to record continuously
for a long time, you may have to replace
the battery with a new one in the midst of
recording. For details on the battery life, refer
to page 12.
*2 The playback of MP3 files recorded using the
IC recorder is also supported.
*3 Not all encoders are supported.
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢂꢅ
Speaker
Approx. 10 mm (13/32 in.) dia.
Supplied accessories
See page 5.
Power output
90 mW
Optional accessories
Active speaker SRS-T88, SRS-T80
Electret condenser microphone ECM-CS10,
ECM-CZ10, ECM-TL1
Audio connecting cable RK-G136HG,
RK-G139HG (excluding Europe)
Rechargeable battery NH-AAA-B2E
USB AC adaptor AC-U50A/AC-U50AD
Battery charger BCG-34HE4
Input/Output
Microphone jack (minijack, stereo)
input for plug in power, minimum input
level 0.6 mV, 3 kilohms or lower impedance
microphone
Headphone jack (minijack, stereo)
output for 8 - 300 ohms headphones
USB connector
Your dealer may not handle some of the
above listed optional accessories. Please
ask the dealer for detailed information.
High-Speed USB compatible
Playback speed control
+100% to –50% (DPC)
Design and specifications are subject to
change without notice.
Power requirements
One LR03 (size AAA) alkaline battery (supplied):
1.5 V DC
Operating temperature
5˚C - 35˚C (41˚F - 95˚F)
Dimensions (w/h/d) (not incl.
projecting parts and controls) (JEITA)*4
34.4 × 99.0 × 13.4 mm (1 3/8 × 4 × 17/32 in.)
Mass (incl. battery) (JEITA)*4
48 g (1 3/4 oz)
*4 Measured value by the standard of JEITA
(Japan Electronics and Information
Technology Industries Association)
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
59
E
Index
Easy Search....................................................................24
Editing Messages.......................................................31
Erasing Messages.......................................................29
External Microphone...............................................20
A
F
B
Battery ..............................................................................11
Battery life ......................................................................12
H
HOLD....................................................................................8
C
I
Connecting the IC Recorder to your
Index to Parts and Controls
Cue/Review...................................................................24
Display window.......................................................8
Front ...............................................................................6
Rear .................................................................................6
D
DPC (the Digital Pitch Control
L
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢃ0
Monitoring the recording ....................................18
M
Maintenance.................................................................58
Menu
N
Noise..................................................................................58
P
Playback modes..........................................................26
Playing Back Message.............................................23
Playing Back MP3.......................................................45
Precautions....................................................................57
Preparing a Power Source....................................11
R
Recording Messages................................................16
Recording time ...........................................................18
Recording with an External Microphone....20
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢃ1
Trademarks
S
Microsoft, Windows and Windows Vista are
registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other
countries.
Setting the Clock .......................................................14
Specifications...............................................................58
System Limitations ...................................................54
Apple, Macintosh and Mac OS are trademarks
of Apple Inc., registered in the USA and other
countries.
Nuance, the Nuance logo, Dragon
NaturallySpeaking, and RealSpeak are trademarks
and/or registered trademarks of Nuance
Communications, Inc., and/or its affiliates in the
United States and/or other countries.
© 2007 Nuance Communications, Inc.
All rights reserved.
T
Troubleshooting.........................................................49
MPEG Layer-3 audio coding technology and
patents licensed from Fraunhofer IIS and Thomson.
U
All other trademarks and registered trademarks
are trademarks or registered trademarks of their
respective holders. Furthermore, “ ™ ”and“ ® ”are not
mentioned in each case in this manual.
USB AC Adaptor..........................................................56
USB Mass Storage Device.....................................48
V
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
62
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢃꢀ
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|