2-693-550-11(1)
LCD Digital Color TV
Operating Instructions
KDL-32S20L1 KDL-40S20L1
© 2006 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
s
s
If the TV is transported directly from a
cold to a warm location, or if the room
temperature changes suddenly, the picture
may be blurred or show poor color due to
moisture condensation. In this case,
WARNING
NOTIFICATION
To reduce the risk of fire or electric shock, do
not expose this apparatus to rain or moisture.
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in
please wait a few hours to let the moisture
evaporate before turning on the TV.
CAUTION
To obtain the best picture, do not expose
the screen to direct illumination or direct
sunlight. It is recommended to use spot
lighting directed down from the ceiling or
to cover the windows that face the screen
with opaque drapery. It is desirable to
install the TV in a room where the floor
and walls are not of a reflective material.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
RISQUE DE CHOC ELECTRIQUE,
NE PAS OUVRIR
PRECAUCION
RIESGO DE CHOQUE ELECTRICO
NO ABRIR
This symbol is intended to
alert the user to the presence
of uninsulated “dangerous
voltage” within the
CAUTION
Use the following Sony appliance(s) only with
the following WALL-MOUNT BRACKET.
s
s
s
Reorient or relocate the receiving
antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
product’s enclosure that
may be of sufficient
magnitude to constitute a
risk of electric shock to
persons.
Sony Appliance Model No.
KDL-32S20L1
KDL-40S20L1
Sony Wall-Mount
Bracket Model No.
SU-PW2
SU-WL51
SU-WL31
This symbol is intended to
alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the
Use with other WALL-MOUNT BRACKET
may cause instability and possibly result in
injury.
s
Pursuant to FCC regulations, you are
cautioned that any changes or modifications
not expressly approved in this manual could
void your authority to operate this
equipment.
To Customers
appliance.
Sufficient expertise is required for installing the
specified product. Be sure to subcontract the
installation to Sony dealers or licensed
contractors and pay adequate attention to safety
during the installation.
The apparatus shall not be exposed to dripping
or splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
CAUTION
Safety
For Customers in the United
States
This product contains mercury. Disposal of this
product may be regulated if sold in the United
States. For disposal or recycling information,
please contact your local authorities or the
Electronics Industries Alliance
To prevent electric shock, do not use this
polarized AC plug with an extension cord,
receptacle or other outlet unless the blades can
be fully inserted to prevent blade exposure.
s
Operate the TV only on 120-240 V AC.
Use the AC power cord specified by Sony
and suitable for the voltage where you use
it.
s
s
s
The plug is designed, for safety purposes,
to fit into the wall outlet only one way. If
you are unable to insert the plug fully into
the outlet, contact your dealer.
If any liquid or solid object should fall
inside the cabinet, unplug the TV
immediately and have it checked by
qualified service personnel before
operating it further.
Note on Caption Vision
This TV provides display of TV closed
captioning in accordance with §15.119 of the
FCC rules.
(http://www.eiae.org).
Note
This television includes a QAM demodulator
which should allow you to receive unscrambled
digital cable television programming via
subscription service to a cable service provider.
Availability of digital cable television
programming in your area depends on the type
of programming and signal provided by your
cable service provider.
Declaration of Conformity
Trade Name: SONY
Model: KDL-32S20L1/KDL-40S20L1
Responsible Party: Sony Electronics Inc.
Address: 16530 Via Esprillo
San Diego, CA 92127 U.S.A.
Telephone Number: 858-942-2230
s
s
If you will not be using the TV for several
days, disconnect the power by pulling the
plug itself. Never pull on the cord.
For details concerning safety precautions,
This device complies with part 15 of the FCC
rules. Operation is subject to the following
two conditions: (1) This device may not
cause harmful interference, and (2) this
device must accept any interference received,
including interference that may cause
undesired operation.
Installing
s
s
s
The TV should be installed near an easily
accessible power outlet.
To prevent internal heat buildup, do not
block the ventilation openings.
Do not install the TV in a hot or humid
place, or in a place subject to excessive
dust or mechanical vibration.
s
Avoid operating the TV at temperatures
below 41°F (5°C).
(Continued)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Trademark Information
TruSurround XT, SRS and (
TruSurround XT technology is incorporated under license from SRS Labs,
Inc.
) symbol are trademarks of SRS Labs, Inc.
Important
Safety
Manufactured under license from BBE Sound, Inc.
Licensed by BBE Sound, Inc. under one or more of the following US
patents: 5510752, 5736897. BBE and BBE symbol are registered
trademarks of BBE Sound, Inc.
Instructions
Macintosh is a trademark licensed to Apple Computer, Inc., registered in
the U.S.A and other countries.
1) Read these instructions.
2) Keep these instructions.
“BRAVIA” and
are trademarks of Sony Corporation.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
®
As an ENERGY STAR Partner, Sony Corporation has
®
determined that this product meets the ENERGY STAR
guidelines for energy efficiency.
®
ENERGY STAR is a U.S. registered mark.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that
produce heat.
This TV incorporates High-Definition
Multimedia Interface (HDMI™) technology.
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing, LLC.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete
outlet.
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate
normally, or has been dropped.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
grounding conductors, location of antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding electrode.
USE
For the TV with a three-wire grounding type AC
power cord plug (Class 1 unit)
This TV must be connected to an AC power socket
outlet with a protective earthing connection.
Antenna Grounding According to the National
Electrical Code, ANSI/NFPA 70
AC power cord
Antenna lead-in wire
Ground clamps
If you damage the AC power cord, it may result in a fire or an electric
shock. If the AC power cord is damaged, stop using it and ask your dealer
or Sony service center to exchange it.
s
Do not place the TV where the power cord is subject to wear or
abuse.
Antenna discharge unit
(NEC Section 810-20)
s
Do not pinch, bend, or twist the cord excessively. The core lines may
be bared and cut, and cause a short-circuit, resulting in a fire or an
electric shock.
Do not convert or damage the power cord.
Do not allow anything to rest on or roll over
the power cord.
Electric service
equipment
Grounding conductors
(NEC Section 810-21)
s
s
Ground clamps
s
s
Do not pull the power cord.
Do not move the TV with the power cord
plugged in.
Keep the power cord away from heat sources.
Be sure to grasp the plug when disconnecting
the power cord.
Power service grounding
electrode system
(NEC Art 250 Part H)
NEC: National Electrical Code
s
s
BATTERIES
s
s
s
Do not dispose of batteries in a fire.
Wall outlet
Do not short circuit, disassemble or overheat the batteries.
Danger of explosion if battery is incorrectly replaced. Replace only
with the same or equivalent type.
Do not use a poor fitting outlet.
Insert the plug fully into the outlet. If it is loose, it may
cause arcing and result in a fire.
Contact your electrician to have the outlet changed.
Disposal of used batteries
To preserve our environment, dispose of used batteries according to your
local laws or regulations.
Wiring
For your safety, unplug the AC power cord when wiring cables.
Cable wiring
CLEANING
Take care not to catch your feet on the cables. It may damage the TV.
s
Clean the AC power plug regularly.
If the plug is covered with dust and it picks
up moisture, its insulation may deteriorate
and result in a fire. Unplug the AC power
plug and clean it regularly.
Electric shock
Do not touch the AC power cord or the TV with a wet
hand. If you plug/unplug the AC power cord from the
TV with a wet hand, it may cause electric shock.
Lightning
s
s
Unplug the AC power cord when
cleaning this TV. If not, it may result in
electric shock.
For added protection for this TV during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna. This will prevent damage to the receiver
due to lightning and power line surges.
Clean the cabinet of the TV with a dry
soft cloth. To remove dust from the
screen, wipe it gently with a soft cloth.
Stubborn stains may be removed with a cloth slightly dampened
with a solution of mild soap and warm water. Never use strong
solvents such as thinner or benzine for cleaning.
If using a chemically pretreated cloth, please follow the instruction
provided on the package.
s
ANTENNA
Outdoor Antenna Grounding
If an outdoor antenna is installed, follow the precautions below. An
outdoor antenna system should not be located in the vicinity of overhead
power lines or other electric light or power circuits, or where it can come
in contact with such power lines or circuits.
MAGNETIC INFLUENCE
This TV contains a strong magnet in the speaker unit that generates a
magnetic field. Keep any items susceptible to magnetic fields away from
the speaker.
WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM,
EXTREME CARE SHOULD BE TAKEN TO KEEP FROM
CONTACTING SUCH POWER LINES OR CIRCUITS AS CONTACT
WITH THEM IS ALMOST INVARIABLY FATAL.
SOUND
Be sure the antenna system is grounded so as to provide some protection
against voltage surges and built-up static charges.
If a snapping or popping sound from the TV is con-
tinuous or frequent while the TV is operating,
unplug the TV and consult your dealer or service
technician. It is normal for some TVs to make occa-
sional snapping or popping sounds, particularly
when being turned on or off.
Section 810 of the National Electrical Code (NEC) in the USA and Section
54 of the Canadian Electrical Code in Canada provides information with
respect to proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit, size of
(Continued)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Objects and ventilation holes
VENTILATION
Never push objects of any kind into the TV through the
cabinet slots as they may touch dangerous voltage points
or short out parts that could result in a fire or an electric
shock. Never spill liquid of any kind on the TV.
The slots and openings in the TV are provided for necessary ventilation.
To ensure reliable operation of the TV, and to protect it from overheating,
these slots and openings must never be blocked or covered.
Unless proper ventilation is provided, the TV may
gather dust and get dirty. For proper ventilation,
observe the following:
Do not place any objects on the TV.
The TV shall not be exposed to dripping or splashing
and no objects filled with liquids, such as vases, shall
be placed on the TV.
s
s
s
Do not install the TV face up or down or
sideways.
Do not install the TV turned over or upside
down.
Never cover the slots and openings with a
cloth or other materials.
MOISTURE
Moisture and flammable objects
s
Do not use power-line operated sets near water
— for example, near a bathtub, washbowl,
kitchen sink, or laundry tub, in a wet basement,
or near a swimming pool, etc. It may result in a
fire or an electric shock.
s
s
Never block the slots and openings by
placing the TV on a bed, sofa, rug or other
similar surface.
s
s
Do not let this TV get wet. Never spill liquid of
any kind on the TV. If any liquid or solid object
does fall through, do not operate the TV. It may
result in electric shock or damage to the TV.
Have it checked immediately by qualified
personnel.
Never place the TV in a confined space, such as
a bookcase or built-in cabinet, unless proper
ventilation is provided.
To prevent fire, keep flammable objects or open flame (e.g. candles)
away from the TV.
CARRYING THE TV
When installing the TV on a wall, allow this much space:
Carry the TV in the specified manner
5.7 cm
30 cm
1
Carrying the TV requires at least two people.
(2 / inches)
7
4
(11 / inches)
8
If you carry the TV in a manner other than that specified and without the
specified number of persons, it may drop and serious injury may result.
10 cm
(4 inches)
10 cm
(4 inches)
s
s
Carry the TV with the specified number of people.
Carry the TV holding the upper and bottom
frames of the TV as illustrated.
s
Hold the TV securely when carrying it.
As the glass surface of the TV has a special
coating, be careful to avoid touching the glass
surface as much as possible.
10 cm (4 inches)
When installing the TV using a stand, allow this much space:
s
s
When transporting, do not subject the TV to shocks or vibration, or
excessive force.
When lifting or moving the TV, be sure to hold the panel firmly as
illustrated. Place your palm directly under the panel, from the rear
of the TV.
30 cm
7
(11 / inches)
8
10 cm
(4 inches)
10 cm
(4 inches)
15 cm
(6 inches)
Never install the TV as follows:
Air circulation is blocked.
Air circulation is blocked.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Placing on a stable surface
INSTALLATION
When installing or removing, using the
Wall-Mount Bracket, be sure to use qualified
contractors. Wall mount installation requires
the use of a Wall-Mount Bracket. If not
properly secured during installation or
removal from the Wall-Mount Bracket, the
TV may fall and cause serious injury. Please
use a qualified contractor when installing or removing.
If you place the TV on an unstable surface, the TV may
fall and cause injury or damage.
Fall
Do not hang anything on the TV.
The TV may fall from the stand or wall-mount, causing
damage or serious injury.
Placement for viewing
It is recommended to watch the TV at a distance of 3 - 7 times that of the
screen height, and in moderate brightness. Watching the TV for too long
or in a dark room may cause eye fatigue.
Attachments
Do not use attachments not recommended by the
manufacturer, as they may cause hazards.
Optional wall mount
Observe the following when installing the TV using a
wall-mount bracket. If the TV is not secured properly, it
may fall and cause injury.
s
Be sure to follow the operating instructions
supplied with the wall-mount bracket when
installing the TV.
Be sure to attach the brackets supplied with the wall-mount bracket.
Do not hang the TV from the ceiling. It may fall and cause serious
injury.
VOLUME ADJUSTMENT
s
Adjust the volume so as not to trouble your neighbors. Sound carries
very easily at night. Therefore, closing the windows or using
headphones is suggested.
s
s
s
When using headphones, adjust the volume so as to avoid excessive
levels, as hearing damage may result.
Outdoor use
Do not install this TV outdoors. If the TV is exposed to
rain, it may result in a fire or an electric shock. If the TV
is exposed to direct sunlight, the TV may heat up and
cause damage to the TV.
LCD SCREEN
s
Although the LCD screen is made with high-precision technology
and has effective pixels of 99.99% or more, black dots or bright
points of light (red, blue, or green) may appear constantly on the
LCD screen. This is a structural property of the LCD panel and is not
a malfunction.
Do not expose the LCD screen surface to direct sun light. Doing so
may damage the LCD panel.
Do not push or scratch the LCD screen, or place objects on top of the
TV. The image may be uneven or the LCD panel may be damaged.
If the TV is used in a cold place, a smear may occur in the picture or
the picture may become dark. This does not indicate a failure. These
phenomenon improve as the temperature rises.
Vehicle
Do not install this TV in a vehicle.
Bumping of the vehicle may cause the TV to fall down
and cause injury.
s
s
s
Ship and vessel
Do not install this TV in a ship or vessel. If the TV is
exposed to seawater, it may cause a fire or damage the
TV.
s
s
Ghosting may occur when still pictures are displayed continuously.
It should disappear after a few moments.
The screen and cabinet get warm when the TV is in use. This is not
a malfunction.
Corrosion
If you use this TV near the seashore, salt may corrode metal parts of the
TV and cause internal damage or fire.
s
s
Avoid spraying insect repellent with volatile material on the screen.
Avoid prolonged contact with rubber or plastic made material.
It may also shorten the life of the TV.
Oils
Do not install this TV in restaurants where oily vapors occur. Dust
absorbing oil may enter and damage the TV.
Broken pieces
Do not throw anything at the TV.
The screen glass may break by the impact and cause serious injury.
Medical institution
Do not place this TV in a place where medical
equipment is in use.
Handling of broken glass and liquid crystal
leakage
It may cause a malfunction of medical instruments.
If the LCD panel gets damaged, crystalline liquid leakage may occur, or
scattered broken glass may result. Do not touch broken glass or crystalline
liquid (which is toxic), with bare hands as cuts or poisoning/skin irritation
may occur. Also, do not let glass fragments or leaked crystalline liquid get
into your eyes or mouth. Should either contact your eyes or mouth, rinse
the contacted area thoroughly with water and consult your doctor.
Preventing the TV from toppling over
Take measures to prevent the TV from toppling over and causing injury.
To prevent the TV from toppling over, secure the TV to a wall or pillar.
Installing on a level surface
If you install the TV on an inclined surface, the TV may
fall or drop and cause injury or damage.
(Continued)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING
Damage requiring service
If the surface of the TV cracks, do not touch the TV until you unplug the
AC power cord.
Otherwise electric shock may result.
Servicing
Do not attempt to service the TV yourself since opening
the cabinet may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
Replacement parts
When replacement parts are required, be sure the service
technician certifies in writing that he/she has used
replacement parts specified by the manufacturer that
have the same characteristics as the original parts.
Unauthorized substitutions may result in a fire, an
electric shock or other hazards.
Safety check
Upon completion of any service or repairs to the TV, ask
the service technician to perform routine safety checks
(as specified by the manufacturer) to determine that the
TV is in safe operating condition, and to so certify.
Should the TV not be repairable, ask a qualified service technician to
dispose of the TV.
DISPOSAL OF THE TV
s
s
Do not dispose of the TV with general household waste.
The LCD contains a small amount of liquid crystal. The fluorescent
tube used in this display also contains mercury. Follow your local
ordinances and regulations for disposal.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
.............................................................................11
Cable System or VHF/UHF Antenna System............................................................11
VCR, Cable and Antenna..........................................................................................13
When Connecting to Optional Equipment...................................................................14
Installing the TV .............................................................................................................16
Bundling the Connecting Cables...............................................................................17
Other Information
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
TM
Welcome to the World of
Thank you for purchasing this Sony LCD Digital Color Television. This
manual is for model KDL-32S20L1 and KDL40S20L1. Be sure to check the
supplied accesories against the list on page 46.
Connecting the TV
To display clear crisp pictures, you must connect your TV correctly and select
“Changing the Wide Screen Mode” on page 21). It is strongly recommended to
connect the antenna/cable input using the supplied 75-ohm coaxial cable to
receive optimum picture quality signal. A 300-ohm twin lead cable can be
easily affected by radio noise and the like, resulting in signal deterioration. If
you use a 300-ohm twin lead cable, keep it as far away from the TV as
possible.
For multiple equipment connections, please refer to the Quick Setup Guide.
Cable System or
VHF/UHF Antenna
System
Cable or VHF/UHF (or VHF only)
75-ohm coaxial
Rear of TV
VHF/UHF input
cable (supplied)
From Cable settings in Setup settings, select Cable On or Cable Off for your type
of input signal.
(Continued)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Cable Box/Digital
Cable Box
Use this hookup if
s
You subscribe to a cable TV system that uses scrambled or encoded
signals requiring a cable box to view all channels, and
s
You do not intend to hook up any other audio or video equipment to
your TV.
75-ohm coaxial
cable (supplied)
Cable
Rear of TV
VHF/UHF input
z To change channels using
the cable box, set your TV
to channel 3 or 4
depending on the cable
box channel output.
Auto Scan will fix the
channel automatically.
IN
jack
OUT
jack
34).
Cable System and
VHF/UHF Antenna
System
If you want to watch both antenna (over-the-air) and cable broadcast signals,
you’ll need to use an optional A-B RF switch (not supplied), as shown
below.
Use the A-B selector to switch between the
A/B
RF Switch
Cable
Rear of TV
over-the-air signals and the cable signals. Then
VHF/UHF input
set the Cable setting in the Setup settings to On
A
B
Antenna
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Satellite Receiver
and Cable/Antenna
Satellite
antenna
cable
Satellite Receiver
CATV/Antenna
cable (supplied)
VHF/UHF
HD/DVD IN
VIDEO IN
S VIDEO
(1080i/720p/480p/480i)
1
3
5
4
Y
S VIDEO
OPTICAL OUT
PB
VIDEO
(yellow)
S VIDEO cable
A/V cable
VIDEO
PR
L
(VAR/FIX)
AUDIO OUT
L
(MONO)
AUDIO-L
(white)
AUDIO-R
(red)
AUDIO
AUDIO
R
R
Rear of TV
If your satellite receiver is not equipped with S VIDEO, use a VIDEO
cable (yellow) instead of the S VIDEO cable.
Run the Initial Setup program, as described in “Setting Up the Channel
VCR, Cable and
Antenna
VCR
CATV cable
Antenna cable
(supplied)
VHF/UHF
HD/DVD IN
VIDEO IN
(1080i/720p/480p/480i)
1
3
5
4
Y
S VIDEO
S VIDEO
OPTICAL OUT
PB
VIDEO
(yellow)
S VIDEO cable
A/V cable
VIDEO
PR
L
(VAR/FIX)
AUDIO OUT
L
(MONO
AUDIO-L (white)
AUDIO-R (red)
AUDIO
AUDIO
R
R
Rear of TV
If your VCR is not equipped with S VIDEO, use a VIDEO cable (yellow)
instead of the S VIDEO cable.
Run the Initial Setup program, as described in “Setting Up the Channel
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
When Connecting to Optional Equipment
Left side
Rear
7
6
VIDEO 2
IN
4
5
RGB
1
2
R-AUDIO-L
S VIDEO
AUDIO
VIDEO
IN
PC IN
L (MONO)
R
AUDIO
0
HD/DVD IN
VIDEO IN
S VIDEO
3
qa
(1080i/720p/480p/480i)
3
1
5
4
Y
OPTICAL OUT
(VAR/FIX)
6
7
PB
VHF/UHF
9
8
VIDEO
PR
L
AUDIO OUT
L
(MONO)
qs
AUDIO
R
AUDIO
R
Item
Description
1 VIDEO 2 IN
Connects to the S VIDEO output jack on your camcorder or other video equipment that has
S VIDEO
S VIDEO. Provides better picture quality than composite video (2). (See Auto YC on page
2
VIDEO 2 IN
VIDEO/
Connect to the composite video and audio output jacks on your camcorder or other video
equipment such as video game equipment.
L (MONO)-
R AUDIO
If you have mono equipment, connect its audio output jack to the TV’s L (MONO)
audio input jack.
3 Headphones
Connects to your headphones. If your headphones do not match the jack, use a suitable plug
adapter (not supplied).
jack
4 PC IN 7
Connect to a personal computer’s video output connector using HD15-HD15 cable (analog
RGB, supplied). Can also be connected to other Analog RGB devices.
(RGB/AUDIO)
See “PC Input Signal Reference Chart” on page 45 for the signals that can be displayed.
For some Apple Macintosh computers, it may be necessary to use an adapter
(not supplied). If this is the case, connect the adapter to the computer before
connecting the HD15-HD15 cable.
If the picture is noisy, flickering or not clear, adjust the Phase and Pitch of the PC
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Item
Description
5 HDMI IN 6
HDMI/
HDMI (High-Definition Multimedia Interface) provides an uncompressed, all-digital
audio/video interface between this TV and any HDMI-equipped audio/video equipment, such
as a set-top box, DVD player, and A/V receiver. HDMI supports enhanced, or high-definition
video, plus digital audio.
R-AUDIO-L
If the equipment has a DVI jack and not an HDMI jack, connect the DVI jack to the HDMI IN
(with HDMI-to-DVI cable or adapter) jack, and connect the audio jack to the AUDIO IN(L/R)
jacks of HDMI IN. (DVI connector is for video signals only.)
HDMI-to-DVI cable
HDMI adapter
Audio cable
Do not connect a PC to the TV’s HDMI input. Use the PC IN (RGB IN) input
instead when connecting a PC.
6 VIDEO IN 1
Connects to the S VIDEO output jack of your VCR or other video equipment that has
S VIDEO
S VIDEO. S VIDEO provides better picture quality than composite video (7).
7 VIDEO IN 1/3
VIDEO/
Connect to the composite video and audio output jacks on your A/V equipment such as a VCR
or other video equipment. A third composite video and audio (VIDEO 2) is located on the left
side panel of the TV.
L(MONO)-
AUDIO-R
8 AUDIO OUT
Connect to the left and right audio input jacks of your audio or video equipment. You can use
these outputs to listen to your TV’s audio through your stereo system.
(VAR/FIX)
9 OPTICAL OUT Connects to the optical audio input of a digital audio equipment that is PCM/Dolby digital
*
(PCM/DOLBY
DIGITAL)
compatible. (OPTICAL OUT is only available for digital channels.)
0 HD/DVD IN 4/5 Connect to your DVD player’s or digital set-top box’s component video (YPBP ) and audio
R
(1080i/720p/
480p/480i)/
L-AUDIO-R
(L/R) jacks. Component video provides better picture quality than the S VIDEO (6) or the
composite video (7) connections.
qa AC IN
qs VHF/UHF
Connects the supplied AC power cord.
RF input that connects to your Cable or VHF/UHF antenna.
* Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Component video (YP P ) or HDMI connection is necessary to view 480p, 720p, and 1080i formats.
B
R
Note that this TV displays all format types of picture in a resolution of 1,366 dots × 768 lines.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Installing the TV
Preventing the TV
from Toppling Over
Attaching the Support Belt
1
2
3
Screw the support belt (supplied) to the TV stand with a wood screw
(supplied).
Attach the support belt to the stand with the securing screw (supplied)
using a coin, etc.
Adjust the length by pulling the support belt towards you while holding
the TV stand.
Be sure to take measures to prevent the TV from toppling over and
causing injury.
The supplied wood screw may not be used depending on the type of TV
stand. In this case, or when the securing strength is not enough,
prepare commercial screws to fit to the TV stand. Use commercial
screws of 3 to 4 mm (1/8 to 3/16 inches) diameter. Consult your dealer
about the types of screw.
When Installing on a Wall
installing the TV on a wall. Refer to the Instruction Guide supplied with the
Wall-Mount Bracket (sold separately).
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Bundling the
You can bundle the connecting cables as illustrated below.
Connecting Cables
1
2
3
Do not bundle the AC power cord with other connecting cables.
Adjusting the
Viewing Angle of the
TV
This TV can be adjusted within the angles shown below.
Adjust the angle left and right (swivel)
Top view
15°
15°
15°
15°
Front
When adjusting the angle, hold the stand with one hand
to avoid slipping or tipping the TV.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Setting Up the Channel List - Initial Setup
After you finish connecting your TV, you need to run Initial Setup, which
automatically sets up available channels. The Initial Setup screen appears
when you turn on your TV for the first time. If you do not want to set up the
channels at this time, you can do it later by selecting the Auto Program
POWER
1
Press
to turn on the TV.
The Initial Setup screen appears.
2
3
Press V/v to highlight the on-screen display language. Then press
.
The message “First please connect cable/antenna. Do you want to start
Auto Program?” appears.
Press B/b to highlight “OK” then press
.
The message “Auto Program” appears. Then the message “Continue
programming digital channels?” appears. This may require 50+ minutes
for completion.
4
Press B/b to highlight “OK” then press
.
If you selected “Cancel” during the Initial Setup, the Initial Setup
message will appear each time you turn on the TV as a reminder until
you complete the Auto Program.
To run Auto Program again at a later time
❑
To add individual digital channels
❑
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
Remote Control
Button
Description
1 TV/VIDEO
Press repeatedly to cycle through the video inputs.
including the Skip function.
1
2
3
2 SLEEP
Press repeatedly until the TV displays the time in minutes
(Off, 15, 30, 45, 60, 90 or 120) that you want the TV to remain
on before shutting off. To cancel Sleep Timer, press SLEEP
repeatedly until Sleep Off appears.
4
5
3 FREEZE
Press once to display a frozen image of the current program in
a window. Press again to show only the frozen image. Press
again to return to the program.
Freeze
Current program
Frozen picture
Move the sub screen with V v B b.
With Freeze function active, some functions are
unavailable, such as MENU.
4 PICTURE
Press repeatedly to cycle through the available picture modes:
Vivid, Standard, Custom. The picture modes can be also
5 GUIDE
Press to display the Guide when you are watching digital
channels (if it is available from the station).
(Digital
channels only)
Using the Guide
The Guide allows you to select the channels from a channel
list. The Guide also provides information about the current
program being shown on each channel.
z The 5 button and CH +
have a tactile dot. Use
them as a reference when
operating the TV.
Make Way for Ducks!
C23.1
Information
banner
Series follows the aquatic misadventures of Henry and Riley, two
FAM
wayward ducks on
a
unique mission.
CC
Alt. Audio
TV-G
Time remaining: 1:26
1
ABC
DISC
FAM
10
23.1
36
Channel
list
Audio
Audio
1
2
Englsih
English
Alternate Audio
TLC
65
HIST
SHOW
68
Program
options
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
Button
Description
Program information in the guide is provided by the
broadcasters. As a result, it may sometimes include
only the channel number, without a program title or
description.
qs
Using the Program Options Setting
The Program Options setting allows you to customize the
program settings on the currently tuned channel.
Each program has a main video and audio
stream (the video or audio that you see or hear
when the channel is first tuned), and may have
alternate streams. This option allows you to
select from the alternate audio streams, when the
broadcaster provides an alternate audio stream
(for instance, the audio may contain a different
language).
Alternate
Audio
(When
6
7
8
available)
6 RETURN
Press to go back to the previous screen when displaying
MENU items and settings.
9
7 MENU
Press to display the MENU with TV functions and settings.
0
qa
8 DIGITAL/
Press to switch between analog and digital channels.
ANALOG
To enjoy the digital features of this TV, press
DIGITAL/ANALOG.
9
Use with 0-9 and ENT buttons to select digital channels. For
example, to enter 2.1, press 2 ,
,
1
and ENT.
0 VOL +/–
Press to adjust the volume.
qa MUTING
Press to mute the sound. Press again or press VOL + to restore
the sound.
qs POWER
Press to turn on and off the TV.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
Button
Description
qd WIDE
Press repeatedly to step through the Wide Mode settings:
Wide Zoom, Normal, Full, Zoom. The Wide Mode settings
Changing the Wide Screen Mode
qd
4:3 Original source
Standard definition source
16:9 Original source
High definition source
qf
qg
m
m
qh
Wide Zoom
Wide Zoom
qj
Normal
Full
Normal
qk
ql
This mode is not available
Full
Zoom
Zoom
qa
When the TV receives a 720p or 1080i signal,
Normal cannot be selected.
qf DISPLAY
Press once to display the current channel number, channel
label, time and Wide Mode settings. The OSD (on screen
display) will turn off after a few seconds or press again to
immediately turn off the display.
qg V/v/B/b
Press V/v/B/b to move the on-screen cursor. Press
select/confirm an item.
to
qh TOOLS
Press to display the Tools Menu that is associated with your
current input: Analog TV, Digital TV, or External Inputs (with
qj JUMP
Press to jump back and forth between two channels. The TV
alternates between the current channel and the last channel that
was selected.
qk 0 - 9 ENT
Press 0 - 9 to select a channel; the channel changes after two
seconds. Press ENT to change channels immediately.
ql CH +/–
Press to scan through channels. To scan quickly through
channels, press and hold down either +/–.
Insert two size AA batteries (supplied) by matching the e and E
on the batteries to the diagram inside the remote control’s battery
compartment.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
TV Controls
1
2
3
4
5
MENU
TV/VIDEO
VOLUME
CHANNEL
POWER
0
PIC OFF/TIMER
STANDBY
POWER
6
7
8
9
Item
Description
1 MENU
2
Press to cycle through the video inputs. If you set a certain input to Skip in Label Video
Inputs, then the input will not appear.
TV/VIDEO
In the MENU screen, this button serves as confirming the selection or setting.
3
Press to adjust the volume. In the MENU screen, these buttons serve as left/right buttons.
– VOLUME +
4
Press to scan through channels. To scan quickly through channels, press and hold down either
– CHANNEL + –/+. In the MENU screen, these buttons serve as up/down buttons.
5 POWER
Press to turn on and off the TV.
6 (IR) Infrared
Receiver/
Receives IR signals from the remote control.
Senses room light level and adjusts the screen brightness accordingly (see page 33 for details).
Do not put anything near the sensor, as its function may be affected.
Light Sensor
7 PIC OFF/
Lights up in green when the Picture Off feature is activated. Lights up in orange when the
timer is set. When the timer is set, this LED will remain lit even if the TV is turned off. For
TIMER LED
8 STANDBY LED Lights up in red when your TV is in PC power saving mode. If the LED blinks in red
continuously, this may indicate the display unit needs servicing (see “Contacting Sony” on
9 POWER LED
Lights up in green when the TV is turned on.
Outputs audio signal.
0 Speaker
The CHANNEL + button has a tactile dot. Use it as a reference when operating the TV.
Make sure that the TV is completely switched off before unplugging the power cord.
Unplugging the power cord while the TV is turned on may cause the Power LED to
remain lit for up to 20 seconds or may cause the TV to malfunction.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
Overview of MENU
MENU provides one button access for controlling your TV. It enables you to perform a variety of tasks intuitively
with a control panel on the screen rather than a variety of remote control button presses.
When you press the MENU button, you can easily perform basic TV functions such as: switching between external
inputs, viewing your favorite analog/digital stations, switching between analog and digital channels, and changing or
customizing your TV settings.
MENU
External Inputs
1
Press MENU on the remote.
MENU control panel appears.
Press V/v to highlight the item.
Analog Favorites
Digital Favorites
Analog
2
3
Press
to select an option.
Digital
2, 3
Press MENU to exit.
Settings
Select from connected equipment
1
Select:
Set:
Exit: MENU
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
MENU
Allows you to
The External Inputs feature lets you select the external inputs
connected to your TV. You can also assign a label using Label
External Inputs
Return
Video 1 VCR
Video 2 GAME
Video 3
Video 4
Video 5
Video 6
Video 7
-
-
-
-
-
1
2
Highlight External Inputs on the MENU control
panel and press
External Inputs
.
Edit Video Labels
Press
V
/v
to highlight the desired external input
.
and press
MENU
Exit:
Select:
Set:
The Analog Favorites feature lets you select programs from a list
Analog Favorites
of up to 16 favorite channels that you specify.
Return
1
Highlight Analog Favorites on the MENU control panel
and press
Press V/v to highlight the desired channel and press
To add the current channel to the list of Favorite Channels,
highlight Add to Favorites and press
Add to Favorites
1
2
3
4
5
6
7
8
28 : -----
60 : -----
28 : -----
65 : -----
68 : -----
28 : -----
-- : -----
-- : -----
.
Analog Favorites
2
.
.
When the Favorite Channels list is full, remove a channel
from your list using Favorite Channels in the Analog Setup (see
accessed directly from Edit Favorites.
Edit Favorites
MENU
Exit: MENU
Select:
Set:
The Digital Favorites feature lets you create a list of up to 16
Favorite Channels
Add to Favorites
Edit Favorites
Exit
favorite channels. To create your favorite list:
1
Highlight Digital Favorites on the MENU control panel
and press
Highlight Add to Favorites and press
.
Digital Favorites
2
to add the
current channel to the list of Favorite Channels.
When the Favorite Channels list is full, remove a channel
from your list using Favorite Channels in the Digital Setup
be accessed directly from Edit Favorites.
The Analog feature takes you to the most recently viewed analog channel. When tuned to the
channel, Channel number will be displayed.
Highlight Analog on the MENU control panel and press
.
Analog
Digital
The Digital feature takes you to the most recently viewed digital channel. When tuned to the
channel, the Program Banner and Channel number will be displayed.
Highlight Digital on the MENU control panel and press
.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
MENU
Allows you to
The Settings feature lets you enter the settings screen. Settings and adjustments can be performed
Navigating Through Settings
Settings
The Settings screen provides access to the features:
1
2
3
4
Press MENU.
Select
Highlight the item: Picture, Sound, Screen, Setup, PC Settings, Analog Setup, Digital Setup.
Press to select an option.
.
To exit Settings, press MENU.
The options you can adjust vary depending on the situation. Unavailable options are
grayed out.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
Using the Picture Settings
Option
Description
Target Inputs
Determines whether to apply Picture Settings to current input only, or to all inputs.
All Inputs
Settings will be applied to “All Inputs” (ex: TV is showing Video 1.
Changes to the picture settings affect TV, Video1 - Video7)
“All Inputs” will override any settings set by “Current Input.”
Current Input
Settings will be applied to only the “Current Input” (ex: TV is
showing Video 1. Changes to picture settings affect only Video 1)
Picture
Vivid
Select for enhanced picture contrast and sharpness.
Mode
Customized picture
viewing
Standard
Select for standard picture settings. Recommended for home
entertainment.
Custom
Allows you to store your preferred settings.
Picture Mode can also be accessed using the TOOLS button on the remote
control when in Analog TV, Digital TV and External Inputs.
Reset
Resets the current Picture Mode setting to the default values.
Adjust to brighten or darken the backlight.
Backlight
Picture
Brightness
Color
Adjust to increase or decrease picture contrast.
Adjust to brighten or darken the picture.
Adjust to increase or decrease color intensity.
Adjust to increase or decrease the green tones.
Hue
Color Temperature
White adjustment
Cool
Select to give the white colors a bluish tint.
Select to give the white colors a neutral tint.
Neutral
Warm 1,2
Select to give the white colors a reddish tint. Available only when
Picture Mode is set to Custom.
Sharpness
Adjust to sharpen or soften the picture.
Noise Reduction
Select to reduce the noise level of connected equipment, and the VHF/UHF input. Select
from Auto, High, Medium, Low and Off.
Auto is only available when you are watching analog channels. It is not available
when Target Input is set to All Inputs.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
Option
Description
Reset
Advanced Settings
Only available in
“Custom Picture Mode”
Resets all the advanced settings to the default settings.
Black Corrector
Enhances black areas of the picture for stronger contrast.
Contrast
Automatically optimizes the contrast. This setting is especially
effective for dark images which increases the vibrancy of the picture.
Enhancer
Gamma
Adjusts the balance between the light and dark areas of the picture.
Emphasizes white and light colors.
Clear White
Live Color
Makes colors more vivid.
MPEG Noise
Reduction
Reduces the mosaic effect in MPEG-compressed video.
Only effective for Digital TV channels.
If the function is set to High, it will reduce the sharpness of the pictures.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
Using the Sound Settings
Option
Description
Target Inputs
Determines whether to apply Sound Settings to current input only, or to all inputs.
All Inputs
Settings will be applied to “All Inputs” (ex: TV is showing Video 1.
Changes to the picture settings affect TV, Video1 - Video7)
“All Inputs” will override any settings set by “Current Input.”
Current Input
Settings will be applied to only the “Current Input” (ex: TV is showing
Video 1. Changes to picture settings affect only Video 1)
Sound Mode
Customized
sound listening
Dynamic
Standard
Custom
Select to enhance treble and bass.
Suitable for spoken dialog.
Flat setting. Allows you to store your preferred settings.
Sound Mode can also be accessed using the TOOLS button on the remote
control when in Analog TV, Digital TV and External Inputs.
Reset
Treble
Bass
Balance
Steady Sound
Resets the current Sound Mode setting to the default values, except MTS.
Adjust to increase or decrease higher-pitched sounds.
Adjust to increase or decrease lower-pitched sounds.
Adjust to emphasize left or right speaker balance.
On
Off
Select to stabilize the volume across all programs and commercials.
Select to turn off Steady Sound.
Surround
BBE
TruSurround XT Select for surround sound (for stereo programs only).
Simulated Stereo Adds a surround-like effect to mono programs.
Off
Select for normal stereo or mono reception.
Select to give sound more impact by compensating for phase effects in speakers. Select from
High, Low, and Off.
MTS
Stereo
Select for stereo reception when viewing a program broadcast in stereo.
Enjoy stereo, bilingual
and mono programs
Auto SAP
Select to automatically switch the TV to second audio programs when a
signal is received. If no SAP signal is present, the TV remains in
Stereo mode.
Mono
Select for mono reception. Use to reduce noise during weak stereo
broadcasts.
MTS is only available for analog programs.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
Using the Screen Settings
Option
Description
Target Inputs
Determines whether to apply Screen Settings to current input only, or to all inputs.
All Inputs
Settings will be applied to “All Inputs” (ex: TV is showing Video 1.
Changes to the picture settings affect TV, Video1 - Video7)
“All Inputs” will override any settings set by “Current Input.”
Current Input
Settings will be applied to only the “Current Input” (ex: TV is showing
Video 1. Changes to picture settings affect only Video 1)
Wide Mode
Wide Zoom
Normal
Select to fill screen with minimum distortion.
Select to display 4:3 picture in original size when the original source is
4:3.
Normal is not available when you are watching 720p or 1080i sources.
Full
Select to enlarge the picture horizontally to fill the screen when the
original source is 4:3 (Standard definition source). When the original
source is 16:9 (High definition source), select this mode to display 16:9
picture in original size.
Zoom
On
Select to enlarge the original picture without distorting the aspect ratio.
Auto Wide
Select to have the screen automatically change to the screen mode that
is best for the current program. If frequent screen changes are disturbing
to you, select Off.
Off
Select to turn off the Auto Wide option. Choose a screen mode from the
Wide Mode option.
(Continued)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
Option
Description
4:3 Default
Wide Zoom
Select to enlarge the 4:3 picture to fill the 16:9 screen, keeping the
original image as much as possible.
Select the default
Screen Mode to use for
4:3 sources
Normal
Off
Select to display the 4:3 picture in its original size.
Select to continue using the current Wide Mode setting when the
channel or input is changed.
If 4:3 Default is set to anything but Off, the Wide Mode setting changes only for
the current channel. When you change channels (or inputs), Wide Mode is
automatically replaced with the 4:3 Default setting for 4:3 sources. To retain the
current Wide Mode setting as channels and inputs are changed, set 4:3 Default
to Off.
Display Area
Select Normal to return to the default display area. Select -1 or -2 to enlarge the picture so
that the edges are outside the visible portion of the screen.
Horizontal Center
Allows you to move the position of the picture left and right.
Press B/b and press
to choose a correction between Min, –4 to +4 and Max.
Horizontal Center feature is useful if TV is connected to game equipment.
Vertical Center
Vertical Size
Allows you to move the position of the picture up and down. Available only in Zoom mode.
Press V/v and press
to choose a correction between Min, –4 to +4 and Max.
Allows you to adjust the vertical size of the picture. (Available only in Wide Zoom and
Zoom modes.)
Press V/v and press
to choose a correction between Min, –4 to +4 and Max.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
Using the Setup Settings
Option
Description
Language
Select to display all on-screen settings in your language of choice: English, Español, Français.
Caption Vision
Allows you to select from several closed caption modes (for programs that are broadcast with
closed captioning). Some caption modes for digital channels are only accessible from the Digital
Off
Caption Vision is turned off.
CC1, CC2,
CC3, CC4
Displays a printed version of the dialog or sound effects of a program.
(Should be set to CC1 for most programs.)
Text1,Text2,
Text3,Text4
Displays network/station information presented using either half or the
whole screen (if available).
Caption Vision can also be accessed using the TOOLS button on the remote
control when in Analog TV, Digital TV and External Inputs (with the exception of PC
input).
Info Banner
Set to On or Off. When on, displays the program name and the remaining time (if the
broadcaster offers this service). Displays for a few seconds when the channel is changed or the
DISPLAY button is pressed.
(Continued)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
Option
Description
Parental Lock
The Parental Lock settings allows you to set up the TV to block programs according to their
content and rating levels. Use 0-9 on the remote control to enter a four-digit password. The first
time you create a password, confirm the password by entering it again.
Lock
Off
Turn Parental Lock off. No programs are
blocked from viewing.
Child
Maximum ratings permitted are:
U.S.: TV-Y, TV-G, G
Canada: C, G, TV-Y
Youth
Maximum ratings permitted are:
U.S.: TV-PG, PG
Canada: C8+, PG, 8 ans+, TV-PG
Young Adult Maximum ratings permitted are:
U.S.: TV-14, PG-13
Canada: 14+, 13 ans+, TV-14
Custom
Select to set ratings manually.
U.S.: See page 34 for details.
If you are not familiar with the Parental Guideline rating system, you should select
Child, Youth, or Young Adult to help simplify the rating selection. To set more
specific ratings, select Custom.
Change Password Select to change your password.
You need your password for any future access into the Parental Lock settings. If
Select Country
U.S.A.
Select to use Canadian ratings (see page 35).
Canada
Label Video Inputs Allows you to identify A/V equipment you connected to the TV, such as a VCR, DVD, etc. For
example, if you have a DVD player connected to the VIDEO 4 jack, you can select the label
DVD for the Video 4 input. Then when you press TV/VIDEO to change inputs, the Video Label
you assigned to that input appears on screen.
1
Press V/v to highlight the video input (Video 1-7) to which you want to assign a label.
Then press to select the input.
Press V/v to highlight one of the displayed labels. Then press
2
to select the label.
You can select from the following labels for each input:
Video 1-6
–, RECEIVER, SATELLITE, CABLE BOX, VCR, DVD, DVR, HD,
GAME, CAMCORDER, Edit:, Skip
Video 7
–, PC, Edit:, Skip
Edit: allows you to create a custom five character label.
If you select Skip, your TV skips this input when you press the TV/VIDEO button.
The Skip label is useful for inputs to which no equipment is connected.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
Option
Description
Auto YC
When connecting both VIDEO IN and S VIDEO IN, you can select the jack from which the TV
receives the input signal. The TV is by default set to receive S VIDEO input signals.
1
2
Press TV/VIDEO repeatedly until the desired video input appears.
After selecting the Auto YC option, to watch the pictures input from the S VIDEO input
jack:
Press V/v to highlight On, then press
.
To watch the pictures input from the VIDEO input jack:
Press V/v to highlight Off, then press
.
Timer Settings
Sleep Timer
Set the time in minutes (Off, 15 min, 30 min, 45 min, 60 min, 90 min, or
120 min) that you want the TV to remain on before shutting off
automatically.
Timer
You can use the Timer to turn the TV on, turn it off, or tune it to a specific
channel at a scheduled time.
Timer feature will not be available until you set the Current Time.
1
Press
V
/
v
to highlight one of the following options, then press
.
Set: Select to set the timer by Day, Time, Duration, Channel and Volume
Setup.
Off: Select to turn off the timer. (Your previous settings are saved.)
2
If you selected Set in step 1, press V/v/B/b to set the day(s), hour,
minute, AM/PM, duration, channel number (VHF/UHF, CATV or
Digital), and volume.
When Digital is selected, the last digital channel you viewed will
automatically show when the TV is turned on.
3
Press MENU to exit Settings.
To return to the Timer Settings after programming the Timer or Current Time, press
B.
Timer will be set to Off when:
- Auto Program for analog channels is executed.
- the AC power cord is disconnected and then reconnected to turn the TV on and
the Current Time is displayed as --:-- --.
Current Time
Select to set the current time (day, hour, minute, and AM/PM).
1
2
3
Press
to select Current Time.
Press V/v/B/b to set the current time (day, hour, minute, and AM/PM).
Press MENU to exit Settings.
Power Saving
Light Sensor
Select to reduce the power consumption by adjusting the backlight brightness. This also
enhances the black level. Select from Off, Low, High and Picture Off.
Select On to enable the automatic picture (screen) brightness control. The light sensor measures
the room brightness which allows the TV to automatically adjust the backlight brightness based
on the picture settings and the ambient room light conditions.
Be sure not to put anything around the sensor, as its function may be affected.
In low light the range of the backlight control is reduced when Light Sensor is set to On.
Quiet Power On
Select to have the TV volume start at the minimum volume and gradually change to the set level
when you turn it on.
(Continued)
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
Option
Description
Speaker
On
Off
Select to turn on the TV speakers.
Select to turn off the TV speakers and listen to the TV’s sound only through
your external audio receiver and speakers.
Audio Out
Easy control of
volume adjustments
Variable
Fixed
When Speaker is set to Off, the audio output from your audio system can be
controlled by the TV’s remote control.
When Speaker is set to Off, the audio output of the TV is fixed. Use your
audio receiver’s remote control to adjust the volume (and other audio
settings) through your audio system.
Cable
On
Off
Select if you are receiving cable channels via Cable TV provider.
Select if you are using an antenna.
You should run Auto Program after changing the Cable setting.
Information
Select to display the equipment information of your TV.
US Models: Selecting Custom Parental Lock Rating Options
To select custom rating options for the U.S., select U.S.A. in the Select Country setting (see page 32).
Option
Description
Movie Rating
G
PG
All children and general audience.
Parental guidance suggested.
PG-13
R
Parental guidance for children under 13.
Restricted viewing, parental guidance is suggested for children under
17.
NC-17 and X
Age-Based Ratings
TV-Y
TV-Y7
TV-G
No one 17 or under allowed.
TV Rating
Block programs by
their rating, content or
both
All children.
Directed to children age 7 and older.
General audience.
TV-PG
TV-14
TV-MA
Parental guidance suggested.
Parents strongly cautioned.
Mature audience only.
Content-Based Ratings
FV
D
L
Fantasy violence.
Suggestive dialogue.
Strong language.
S
Sexual situations.
V
Violence.
To ensure maximum blocking capability, set the Age-Based Ratings.
Unrated
Allow
Block
Allows programs and movies that are broadcast without a rating.
Blocks all programs and movies that are broadcast without a rating.
Block programs or
movies that are
broadcast without a
rating
If you block unrated TV programs, be aware that the following types of programs
may be blocked: programs broadcast from another country, emergency
broadcasts, political programs, sports, news, public service announcements,
religious programs and weather.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
Canadian Models: Selecting Custom Parental Lock Rating Options
To select custom rating options for Canada, select Canada in the Select Country setting (see page 32).
Option
Description
English Rating
C
All children.
C8+
G
Children 8 years and older.
General programming.
PG
Parental guidance.
14+
Viewers 14 and older.
18+
Adult programming.
French Rating
U.S.A. Rating
G
General programming.
8 ans+
13 ans+
16 ans+
18 ans+
Not recommended for young children.
Not recommended for ages under 13.
Not recommended for ages under 16.
Programming restricted to adults.
Viewing Blocked Programs
You can view blocked programs by entering the password. Press ENT when tuned to a blocked program,
then enter the password. This temporarily turns the parental control feature off. To reactivate the Parental
Lock settings, turn off the TV. When the TV is turned on again, your Parental Lock settings are reactivated.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
Using the PC Settings
Option
Description
Normal
Full1
Wide Mode
Select to display in the original image size.
Select to enlarge the picture to fill the display area, keeping its original
aspect ratio.
Full2
Select to enlarge the picture to fill the display area.
Reset
Resets the current setting to its default setting.
Auto Adjustment
Select to automatically adjust the display position and phase of the picture when the TV
receives an input signal from the connected PC. Note that Auto Adjustment may not work
well with certain input signals. In such cases, manually adjust the options below.
Auto Adjustment for PC can also be set using the TOOLS button on the remote
control.
Phase
Pitch
Adjust after Pitch to fine tune overall sharpness.
Adjust uneven sharpness on screen.
For the PC Input Signal Reference Chart, see page 45.
Allows you to move the position of the picture left and right.
Horizontal Center
Vertical Center
Press B/b and press
to choose a correction between Min, –49 to +49 and Max.
Allows you to move the position of the picture up and down.
Press V/v and press
to choose a correction between Min, –49 to +49 and Max.
Power Management
On
Select to automatically switch to the power saving mode when there is
no signal input for 30 seconds.
Off
Select to turn off Power Management.
Power Management is not VESA-compliant.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
Using the Analog Setup Settings
Option
Description
Favorite Channels
Lets you set up a list of up to 16 of your favorite channels.
1
Press V/v to highlight a Favorite Channel number (1-16) which you want to make your
Favorite Channel, then press to select it.
Press to scroll through the channels until you find the channel that you would like to
add and then press to select it.
To add other Favorite Channel numbers, repeat steps 1-2
2
V/v
.
Favorite Channels for Analog TV can also be set using the TOOLS button on
the remote control.
Auto Program
Automatically sets up the channel list on the TV for all receivable channels.
1
2
Select Auto Program.
Select OK to start Auto Program. When Auto Program is done, the Show/Hide
Channels screen will appear. (See below)
Show/Hide Channels Allows you to show or hide channels that appear when you use the CH +/– buttons.
1
Press V/v to scroll through the channels until you find the channel you want to show or
hide. Then press to select it.
2
Press V/v to determine if the channel will be shown or hidden.
To show or hide more channels, repeat steps 1-2.
Channels that you set to be hidden can be accessed only with the 0-9 buttons.
Label Channels
Allows you to assign labels (such as station call letters) to channel numbers.
1
Press V/v to scroll through the channel numbers. Then press
number that you want to assign a label.
to select the channel
2
Press V/v to scroll through the label characters (A-Z, 0-9, etc.). Press b to move to the
next character. Repeat to add up to 5 characters to the label. Press b to highlight OK
and press
to set.
To assign labels to more channels, repeat steps 1-2.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
Using the Digital Setup Settings
Highlight Digital
Setup and press
.
The Digital Setup option
appears.
Option
Description
Digital Channels
Favorite
Lets you set up a list of up to 16 of your favorite channels.
Channels
1
Press V/v to highlight a Favorite Channel number (1-16) which
you want to make your Favorite Channel.
2
Enter the number you wish to assign to the channel. Reset will
remove the existing Favorite Channel and Surf will take you to the
Favorite Channel list.
To select other Favorite Channel numbers, repeat steps 1-2.
Select to add digital channels.
Digital Channels Add
Auto Program
Automatically sets up the channel list on the TV for all receivable
digital channels.
1
2
Select Auto Program then Start.
Select OK to start Auto Program. When Auto Program is done,
select OK.
Show/Hide
Channels
Allows you to show or hide channels that appear when you use the CH
+/– buttons.
1
Press V/v to scroll through the channels until you find the channel
you want to show or hide.
2
Press
to determine if the channel will be shown or hidden.
To show or hide more channels, repeat steps 1-2.
Channels that you set to be hidden can be accessed only with the 0-9 buttons.
Label Channels Allows you to assign labels (such as station call letters) to channel
numbers.
1
Press V/v to scroll through the channel numbers. Then press
to select the channel number that you want to assign a label.
2
Press V/v to scroll through the label characters (A-Z, 0-9, etc.).
Press b to move to the next character. Repeat to add up to 7
characters to the label. Then press
to set it.
To assign labels to more channels, repeat steps 1-2.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
Option
Description
Digital Setup
Caption Vision
Allows you to select from several closed-caption modes for digital
On
Caption Vision is turned on.
Off
Caption Vision is turned off.
Program
Allows you to set basic and advanced Caption Vision
options. See “Programming Caption Vision” below.
A/V Sync
Off/1/2/3
Use this option to make adjustments to audio and video
synchronization when you have external equipment
connected to OPTICAL OUT of the TV. Select Off
(default setting) to make no adjustments. Select 1, 2 or
3 to adjust so that the video and audio from your
connected external equipment are synchronized.
Diagnostics
Display diagnostics information about the TV. This can be useful in pro-
viding information to an authorized technician or repair person.
Parental Lock
The Parental Lock option in the Digital Setup settings allows you to set up the TV to block
digital programs that contain digital ratings.
This setting is only available if digital ratings have been downloaded by your TV
and ratings have been set for U.S.A. in the Setup settings (see page 31).
Password
If the password has not been set, or to change the password, use
Digital Rating
Off
Turn Parental Lock off. No programs that contain
downloadable ratings are blocked from viewing.
Custom...
Clear All
Select to block programs based on downloadable ratings.
Select to clear the entire downloadable rating system.
This action will delete the current Digital Rating menu and
the menu will no longer be available until the TV is tuned to a
channel that contains downloadable ratings.
Programming Caption Vision
If you selected the Program option under Caption Vision, you can change the following settings:
Option
Description
Basic
Allows you to select basic analog (EIA-608) closed caption options.
CC1, CC2,
CC3, CC4
Text1, Text2,
Text3, Text4
Digital CC
Advanced
Allows you to set digital closed captioning to Basic (digital EIA-608) or Advanced (digital
EIA-708).
Allows you to select advanced digital (EIA-708) closed caption options. Select from the
available options.
(Continued)
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
Option
Description
Advanced Settings
Allows you to make additional settings for digital (EIA-708) closed caption options. Select
from As Broadcast, Small Text, Large Text and Custom.
Custom...
Allows you to customize the following settings:
Character Size
Character Style
Character Color
Character Opacity
Edge Color
Small, Standard, Large
Style 1-7
Color 1-8
Solid, Translucent
Color 1-8
Edge Type
None, Raised, Depressed, Outline,
Left Shadow, Right Shadow
Background Color
Background Opacity
Window Color
None, Color 1-8
Solid, Translucent
None, Color 1-8
Solid, Translucent
Window Opacity
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
Troubleshooting
If you have additional questions, service needs, or required technical assistance related to the use of your
Sony TV, please visit our website or call one of the following numbers:
1-800-222-SONY(7669) for US Residents
1-877-899-SONY(7669) for Canadian Residents
Problem
Possible Remedies
No picture.
No picture.
❑
Cannot receive any channels.
❑
❑
❑
Make sure the power cord is connected securely.
Turn on the power of the TV.
Check antenna/cable connections.
TV is locked to one channel.
❑
Perform Auto Program to add receivable channels that are not presently in the
TV’s memory (pages 37 and 38).
Cannot receive or select channels. ❑ Perform Auto Program to add receivable channels that are not presently in the
TV’s memory (pages 37 and 38).
❑
To receive or select cable channels, make sure that Cable in the Setup settings
sure Cable is set to Off.
The TV turns off automatically.
❑
❑
Check if the Sleep Timer is activated, or confirm the Duration setting of Timer.
(page 33).
No picture from some video
sources.
❑
❑
❑
Check the connection between the optional video equipment and the TV.
If you connect video equipment to the S VIDEO input of the TV, set Auto YC to
❑
Press MENU on the remote control. Select your desired input from the External
Inputs list.
Poor picture.
Double images or ghosts.
❑
❑
Check antenna/cable connections.
Check the antenna location and direction.
Only snow and noise appear on the ❑ Check if the antenna is broken or bent.
screen.
❑
Check if the antenna has reached the end of its serviceable life. (3-5 years in
normal use, 1-2 years at the seaside.)
Dotted lines or stripes.
❑
❑
Keep the TV away from noise sources such as cars, motorcycles, or hair-dryers.
If using 300 ohm twin lead, move the excess lead away from the TV or try using
75 ohm coaxial cable instead.
correct/The picture is too bright.
❑
❑
If you set the Power Saving mode to Low or High, it will enhance the black
level.
Noisy picture.
❑
Make sure that the antenna is connected using the supplied 75-ohm coaxial
cable.
❑
❑
Keep the antenna cable away from other connecting cords.
To avoid TV interference, make sure to use an undamaged antenna cable.
(Continued)
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
Problem
Possible Remedies
No sound/Noisy sound
Good picture, no sound.
❑
Check the volume control.
❑
Press MUTING or VOL + so that “Muting” disappears from the screen
(page 20).
❑
❑
Disconnect your headphones.
not output from the TV’s speakers regardless of the TV’s volume control.
Audio noise.
❑
Make sure that the antenna is connected using the supplied 75-ohm coaxial
cable.
❑
❑
Keep the antenna cable away from other connecting cords.
To avoid TV interference, make sure to use an undamaged antenna cable.
Wide Mode changes automatically.
❑
The current Wide Mode setting is automatically replaced with the 4:3 Default
setting when you change the channel or video input, if 4:3 Default in the Screen
settings is set to other than Off. If you want to lock in the Wide Mode selected
You have selected a text option in the Setup/Digital Setup setting and no text is
set the Caption Vision option to Off. If you were trying to select closed
captioning, select CC1 instead of Text1-4.
❑
❑
“Black box” on screen.
Black bands appear at the top and
bottom of the screen.
❑
❑
Some wide screen programs are filmed in aspect ratios that are greater than 16:9
(this is especially common with theatrical releases). Your TV will show these
programs with black bands at the top and bottom of the screen. For more details,
check the documentation that came with your DVD (or contact your program
provider).
The compression used by certain digital broadcasts and DVDs may cause your
TV’s screen to display less detail than usual, or cause artifacts (small blocks or
dots, pixelations) to appear on your screen. This is due to your TV’s large screen
and ability to show very fine detail, and is normal for certain digitally recorded
programs.
Certain programs on DVD or other
digital sources display a loss of
detail, especially during fast-motion
or dark scenes.
Remote control does not operate.
❑
❑
❑
Check the polarity of the batteries or replace the batteries.
Point the remote control at the remote control sensor of the TV.
Florescent lamps can interfere with your remote control operation; try turning
off the florescent lamps.
❑
❑
Keep the remote control sensor area clear from obstacles.
Some digital cable channels are not
being displayed.
Certain cable companies have limitations on the broadcast of digital cable
channels. Check with your cable company for more information.
The digital cable channel may be set to Hidden in the Show/Hide Channels
Select the Parental Lock settings on the settings screen, then enter the following
master password: 4357. The master password clears your previous password and
allows you to enter a new password (page 32).
❑
❑
Lost password.
How to reset the TV to factory
settings.
❑
Turn on the TV. While holding down the V button on the remote control, press
the POWER button on the TV. (The TV will turn itself off, then back on again.)
Release the V button.
WARNING: The Reset will clear all of your customized settings including
Parental Lock setting.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
Preparation for Wall Mounting the KDL-32S20L1
This TV can be installed on a wall by using a wall-mount bracket (sold
separately). Before mounting the TV on a wall, the Table-Top Stand must be
removed from the TV.
Do not remove the Table-Top Stand for any reason other than to wall-
mount the TV.
Follow the simple steps below to remove the Table-Top Stand:
1
2
3
Disconnect all the cables from the TV.
Sony Wall-Mount
Bracket Model
SU-WL31
Cover a level and stable surface with a thick and soft cloth.
Gently lay the TV, face down, onto the cloth. Make sure the Table-Top
Stand is hanging over the edge.
(KDL-32S20L1)
4
5
Rotate the cable holder 90 degrees, and pull it out completely. [See
illustration A]
Remove the screws and detach the Table-Top Stand from the TV. [See
illustration B] Be sure to hold the Table-Top Stand firmly while
removing the last screw.
6
Do not remove any other screws from the TV.
For bracket installation, refer to the instruction guide provided by the Wall-
Mount Bracket model for your TV. Sufficient expertise is required in
installing this TV, especially to determine the strength of the wall for
withstanding the TV’s weight. For product protection and safety reasons,
Sony strongly recommends that you use the Wall-Mount Bracket model
designed for your TV and the wall-mounting of your TV should be
performed by Sony dealers or licensed contractors.
Be sure to store the removed screws and Table-Top Stand in a safe
place until you are ready to reattach the Table-Top Stand. Keep the
screws away from small children.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
Preparation for Wall Mounting the KDL-40S20L1
This TV can be installed on a wall by using a wall-mount bracket (sold
separately). Before mounting the TV on a wall, the Table-Top Stand must be
removed from the TV.
Do not remove the Table-Top Stand for any reason other than to wall-
mount the TV.
Follow the simple steps below to remove the Table-Top Stand:
SonyWall-Mount
Bracket Models
SU-WL51 and
SU-PW2
1
2
Disconnect all the cables from the TV.
Start removing the screws from the ones on top. (See illustration below)
Do not remove any other screws from the TV.
3
When screws are removed, lift the TV out. Make sure that you carry out
this task with two people. Do not attempt to lift the TV by your self.
(KDL-40S20L1)
For bracket installation, refer to the instruction guide provided by the Wall-
Mount Bracket model for your TV. Sufficient expertise is required in
installing this TV, especially to determine the strength of the wall for
withstanding the TV’s weight. For product protection and safety reasons,
Sony strongly recommends that you use the Wall-Mount Bracket model
designed for your TV and the wall-mounting of your TV should be
performed by Sony dealers or licensed contractors.
Be sure to store the removed screws and Table-Top Stand in a safe
place until you are ready to reattach the Table-Top Stand. Keep the
screws away from small children.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
PC Input Signal Reference Chart
Resolution
Signals
Horizontal frequency
(kHz)
Vertical
frequency (Hz)
Standard
Horizontal
(Pixel)
640
640
720
800
800
1024
1024
1024
1280
1280
1360
×
Vertical
(Line)
480
480
400
600
600
768
768
768
768
768
768
VGA
×
31.5
37.5
31.5
37.9
46.9
48.4
56.5
60.0
47.4
47.8
47.7
60
75
70
60
75
60
70
75
60
60
60
VGA
VESA
VGA-T
×
×
×
×
×
×
×
×
×
×
SVGA
XGA
VESA Guidelines
VESA
VESA Guidelines
VESA
VESA
VESA
VESA
VESA
WXGA
This TV's PC Input does not support Sync on Green or Composite Sync.
This TV's PC Input does not support interlaced signals.
For the best picture quality, it is recommended to use the signals in the above chart with a 60Hz vertical
frequency from a personal computer. In plug and play, signals with a 60Hz vertical frequency will be
selected automatically.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
Specifications
For All Models
Television system:
NTSC
AUDIO OUT:
American TV standard
ATSC compliant 8VSB
ANSI/SCTE 07 2000
(Does not include CableCARD
functionality)
500 mVrms (100% modulation)
ATSC (8VSB terrestrial)
QAM on cable
More than 1 Vrms at the maximum volume setting (Variable)
More than 500 mVrms (Fixed)
PC IN 7:
D-sub 15-pin, analog RGB, 0.7 Vp-p, 75 ohms, positive
See the PC Input Signal Reference Chart on page 45
Analog
Digital
Channel coverage:
Terrestrial
2-69
2-69
1-135
PC AUDIO INPUT:
Stereo mini jack, 0.5 Vrms, 1 kilohm
Cable
Antenna:
1-125
75-ohm external terminal for VHF/UHF
Headphones:
Stereo mini jack
Panel System:
LCD (Liquid Crystal Display) Panel
Impedance: 16 ohms
Power Requirement:
120 V-240 V AC, 50/60 Hz
Display resolution (horizontal × vertical):
1,366 dots × 768 lines
VIDEO IN 1/2/3:
S VIDEO (4-pin mini DIN) (VIDEO 1/2 only):
Y: 1.0 Vp-p, 75 ohms unbalanced, sync negative
Supplied accessories:
Remote control RM-YD005 (1)
Size AA batteries (2)
75-ohm coaxial cable (1)
AC power cord (1)
C: 0.286 Vp-p (Burst signal), 75 ohms
1 Vp-p, 75 ohms unbalanced, sync negative
500 mVrms (100% modulation)
Impedance: 47 kilohms
VIDEO:
AUDIO:
HD15-HD15 cable (1)
Support belt (1), securing screw (1) and wood screw (1)
Cable holder (1)
Operating Instructions (1)
Quick Setup Guide (1)
Warranty Card (1)
HD/DVD IN 4/5:
YP P (Component Video):
B
R
Y: 1.0 Vp-p, 75 ohms unbalanced,
sync negative
PB: 0.7 Vp-p, 75 ohms
PR: 0.7 Vp-p, 75 ohms
Online Registration Card (U.S.A. only) (1)
Signal format: 480i, 480p, 720p, 1080i
500 mVrms (100% modulation)
Impedance: 47 kilohms
AUDIO:
Optional accessories:
Headphones plug adapter
Connecting cables
HDMI IN 6:
HDMI:
Wall-Mount Bracket:
SU-PW2 (KDL-40S20L1)
SU-WL31 (KDL-32S20L1)
SU-WL51 (KDL-40S20L1)
Video: 480i, 480p, 720p, 1080i
Audio: Two channel linear PCM 32, 44.1 and
48 kHz, 16, 20 and 24 bits
AUDIO:
500 mVrms (100% modulation)
Impedance: 47 kilohms
Optional accessories availability depends on its stock.
KDL-40S20L1
KDL-32S20L1
By Model
40
32
Screen size (in inches)
Speaker/Full range (2)
(in mm)
55 × 150
2 1/4 × 6
200 W
42 × 150
1 11/16 × 6
150 W
(in inches)
Power consumption (in use)
(in standby)
All models less than 0.1 W
Dimensions
with stand (in mm)
with stand (in inches)
without stand (in mm)
without stand (in inches)
Mass
988 × 716 × 334
39 × 28 1/4 × 13 1/4
988 × 664 × 103
792 × 593 × 219
31 1/4 × 23 3/8 × 8 5/8
792 × 546 × 99
39 × 26 1/4 × 4 1/8
31 1/4 × 21 1/2 × 4
with stand (in kg.)
with stand (in lb.)
without stand (in kg.)
without stand (in lb.)
27.0
59.5
17.0
37.44
15.0
33
21.0
46.19
Design and specifications are subject to change without notice.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
4:3 Default 30
S
Hue 26
S VIDEO jack, described 14, 15
Setting up channels 18
Settings
A
I
A/V Sync 39
AC IN 15
Info Banner 31
Analog Setup 37
Digital Setup 38
PC 36
Advanced Settings 27
Alternate Audio 20
Audio Out 34
Information 34
Infrared Receiver (IR) 22
Picture 26
AUDIO OUT jack, described 15
Auto Adjustment 36
Auto SAP, MTS setting 28
Auto Wide 29
Screen 29
J, K
Setup 31
JUMP button 21
Sound 28
Sharpness 26
L
SLEEP button 19
Sound Mode 28
Speaker 34
Auto YC 33
Label Video Inputs 32
Language 31
B
Backlight 26
Balance 28
Bass 28
Light Sensor
STANDBY LED 22
Steady Sound 28
Stereo, MTS setting 28
Support Belt 16
Surround 28
Described 22
Setting 33
BBE 28
Bilingual audio 28
Brightness 26
M
Swivel 17
MENU
Analog 24
C
T, U
Analog Favorites 24
Digital 24
Cable
TIMER LED 22
with VCR, connecting 13
Channels
Digital Favorites 24
Settings 25
Timer Settings 33
TOOLS button 21
Treble 28
Mono, MTS setting 28
Movie Rating 34
MTS 28
TruSurround XT 28
Turning on/off the TV 22
TV Rating 34
Setting up 18
Closed caption modes 31
Color 26
MUTING button 20
Color Temperature 26
Current Time 33
N
TV/VIDEO button 19
Unrated 34
Noise Reduction 26
US Models 34
D
O
Diagnostics 39
V
OPTICAL OUT 15
Digital Channels 38
Digital Setup 39
VCR
P, Q
With cable, connecting 13
Vertical Size 30
DIGITAL/ANALOG button 20
Display Area 30
PC IN 14
DISPLAY button 21
Dynamic, Sound Mode 28
VHF/UHF input, described 15
VIDEO/AUDIO (L/R) jacks, described
14, 15
Phase 36
PIC OFF LED 22
Picture 26
E
Viewing Blocked Programs 35
PICTURE button 19
Picture Mode 26
Pitch 36
English Rating 35
ENT button 21
W, X, Y
POWER LED 22
Power Management 36
Power Saving 33
Program Options 20
Quiet Power On 33
F
WIDE button 21
FREEZE button 19
French Rating 35
G
GUIDE button 19
H
R
HD/DVD IN jack (1080i/720p/480p/
480i), described 15
RETURN button 20
HDMI IN jack, described 15
Headphones jack, described 14
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|