Sony Stereo System CMT GPZ6 User Manual

2-591-383-12(1)  
Micro HI-FI  
Component  
System  
Operating Instructions  
CMT-GPZ7  
CMT-GPZ6  
©2005 Sony Corporation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Which discs can you play  
on this system?..................................5  
Viewing information about the disc  
in the display .................................. 24  
Viewing the tuner information in the  
display ............................................ 25  
Listening to audio from a connected  
component ...................................... 27  
Recording audio from a connected  
component ...................................... 27  
Recording on a connected  
component ...................................... 27  
Recording your favorite CD tracks  
on a tape..........................................20  
3GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Create your own ATRAC CDs  
In addition to the usual audio CDs, you can play an original CD, called “ATRAC CD,” that you create  
with the supplied software, SonicStage. Using SonicStage, about 30 audio CDs* can be recorded on  
one CD-R or CD-RW. The following is a quick overview of how you listen to music on your ATRAC  
CD.  
Install SonicStage on your computer.  
SonicStage is software that takes music downloaded from  
audio CDs on your computer and creates original CDs. It  
can be installed from the supplied CD-ROM.  
ATRAC CD  
Create an ATRAC CD.  
After selecting your favorite songs from music  
stored on your computer, record them on a CD-R/  
CD-RW using SonicStage.  
Audio CDs,  
MP3 files  
Listen to them with this system.  
You can enjoy lots of songs on your original CD.  
Please see the supplied “Installation/Operating Guide” for how to install SonicStage and how to create  
ATRAC CDs.  
* When the total playing time of one CD (album) is estimated at 60 minutes and you are recording on  
a 700MB CD-R/CD-RW at 48 kbps in ATRAC3plus format.  
4GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Which discs can you play on this system?  
Audio CDs:  
CD-DA format CDs  
CD-DA (Compact Disc Digital Audio) is a recording standard used for audio CDs.  
ATRAC CDs:  
CD-R/CD-RW on which audio data compressed in the ATRAC3plus format has  
been recorded by using SonicStage*  
ATRAC3plus (Adaptive Transform Acoustic Coding3plus) is audio compression technology  
that satisfies the demand for high sound quality and high compression rates. ATRAC3plus can  
compress audio files to about 1/20 of their original size at 64 kbps.  
Bit rates and sampling frequencies this system can play are:  
Bit rates  
Sampling frequencies  
44.1 kHz  
ATRAC3  
66/105/132 kbps  
8 – 352 kbps  
ATRAC3plus  
44.1 kHz  
Up to 62 characters can be displayed on this system.  
MP3 CDs:  
CD-R/CD-RW on which audio data compressed in the MP3 format has been  
recorded by using a software other than SonicStage*  
Bit rates and sampling frequencies this system can play are shown below. Variable Bit Rate  
(VBR) files can also be played.  
Bit rates  
Sampling frequencies  
32/44.1/48 kHz  
MPEG-1 Layer3  
MPEG-2 Layer3  
MPEG-2.5 Layer3  
32 – 320 kbps  
8 – 160 kbps  
8 – 160 kbps  
16/22.05/23 kHz  
8/11.025/12 kHz  
This system conforms to Version 1.0/1.1/2.2/2.3/2.4 of the ID3 tag format. ID3 tag is a format  
for adding certain information (track title, album name, artist name, etc.) to MP3 files. Up to  
124 characters of ID3 tag information can be displayed on this system.  
An ATRAC CD on which audio data compressed in the MP3 format has been recorded using software  
other than SonicStage can also be played.  
With SonicStage, you cannot create a CD on which mixed format audio data is recorded.  
* Only ISO9660 Level 1/2 and Joliet extension format discs can be played.  
continued  
5GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
2)  
Multi Session  
List of playable discs  
This is a recording method that enables adding of  
data using the Track-At-Once method.  
Conventional CDs begin at a CD control area called  
the Lead-in and end at an area called Lead-out. A  
Multi Session CD is a CD having multiple sessions,  
with each segment from Lead-in to Lead-out  
regarded as a single session.  
Format of discs  
Disc logo  
Audio CDs  
CD-R/CD-RW  
(audio data, ATRAC3plus  
files, MP3 files)  
CD-Extra: This format records audio (audio CD  
data) on the tracks in session 1 and data on the tracks  
in session 2.  
Mixed CD: This format records data on the first  
track and audio (audio CD data) on the second and  
subsequent tracks of a session.  
Discs that this system cannot  
play  
Notes on CD-R and CD-RW  
• Some CD-Rs or CD-RWs cannot be played  
on this system depending upon the recording  
quality or physical condition of the disc, or  
the characteristics of the recording device.  
Furthermore, the disc will not play if it has not  
been correctly finalized. For more  
information, see the operating instructions for  
the recording device.  
• CD-ROMs  
• CD-Rs/CD-RWs other than those recorded in  
the following formats:  
– music CD format  
– ATRAC3plus format and MP3 format that  
conform to ISO96601) Level 1/Level 2,  
Joliet or Multi Session2)  
• Discs with non-standard shapes (e.g., heart,  
square, star) cannot be played on this unit.  
Attempting to do so may damage the unit. Do  
not use such discs.  
• A disc with paper or stickers on it.  
• A disc that has the adhesive, cellophane tape,  
or a sticker still left on it.  
• Discs recorded on CD-R/CD-RW drives may  
not be played back because of scratches, dirt,  
recording condition or the driver’s  
characteristics.  
• CD-R and CD-RW discs recorded in multi-  
session that have not ended by “closing the  
session” are not supported.  
• With formats other than ISO9660 Level 1 and  
2, folder names or file names may not be  
displayed correctly.  
• The following discs take a longer time to start  
playback.  
• An 8 cm disc with an adaptor  
1)  
ISO9660 Format  
The most common international standard for the  
logical format of files and folders on a CD-ROM.  
There are several specification levels. In Level 1,  
file names must be in the 8.3 format (no more than  
eight characters in the name, no more than three  
characters in the extension) and in capital letters.  
Folder names can be no longer than eight characters.  
There can be no more than eight nested folder  
levels. Level 2 specifications allow file names and  
folder names up to 31 characters long. Each folder  
can have up to 8 trees.  
– a disc recorded with complicated tree  
structure.  
– a disc recorded in Multi Session.  
– a disc to which data can be added (non-  
finalized disc).  
For Joliet in the expansion format (file and folder  
names can have up to 64 characters) make sure of  
the contents of the writing software, etc.  
6GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Music discs encoded with  
copyright protection  
technologies  
About ATRAC CDs and  
MP3 CDs  
This product is designed to playback discs that  
conform to the Compact Disc (CD) standard.  
Recently, various music discs encoded with  
copyright protection technologies are marketed  
by some record companies. Please be aware that  
among those discs, there are some that do not  
conform to the CD standard and may not be  
playable by this product.  
The structure of ATRAC CDs  
and MP3 CDs  
ATRAC CDs and MP3 CDs consist of “files”  
and “groups.” A “file” is equivalent to a “track”  
of an audio CD. A “group” is a bundle of files  
and is equivalent to an “album.” For MP3 CDs,  
this system recognizes an MP3 folder as a  
“group” so that ATRAC CDs and MP3 CDs can  
be operated in the same way.  
Playing order of ATRAC CDs  
and MP3 CDs  
For ATRAC CDs, files are played in the order  
selected in SonicStage. For MP3 CDs, the  
playing order may differ depending on the  
method used to record MP3 files on the disc. In  
the following example, files are played in order  
of 1 to 7.  
Group  
File  
MP3 CD  
(Maximum directory level: 8)  
continued  
7GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
The usable number of groups and  
files  
ATRAC CDs:  
• Maximum number of groups: 255  
• Maximum number of files: 999  
MP3 CDs:  
• Maximum number of groups: 256  
• Maximum number of files: 511  
(The maximum number of MP3 files and groups that  
can be contained on a single disc is 512.)  
Notes  
• The system may be unable to play MP3 files that do  
not have the “.MP3” extension.  
• Attempting to play non-MP3 files that have the  
“.MP3” extension may result in noise or malfunction.  
• If ATRAC3plus files and MP3 files are recorded on  
the same disc, this system plays the ATRAC3plus  
files first.  
• On a disc that has ATRAC3plus and MP3 files, do  
not save files in other formats and do not make  
unnecessary folders.  
• To compress a source in an MP3 file, we recommend  
setting the compression parameters to “44.1 kHz,”  
“128 kbps,” and “Constant Bit Rate.”  
• To record up to the maximum capacity, set the  
writing software to “halting of writing.”  
• To record to the maximum capacity at one time up on  
media that has nothing recorded on it, set the writing  
software to “Disc at Once.”  
Cautions when playing a disc  
that is recorded in Multi  
Session  
• If the disc begins with a CD-DA session, it is  
recognized as a CD-DA (audio) disc, and  
ATRAC3plus/MP3 sessions are not played  
back.  
• If the disc begins with an ATRAC3plus/MP3  
session, it is recognized as an ATRAC CD/  
MP3 CD, and CD-DA (audio) sessions are not  
played back.  
• The playback range of an MP3 CD is  
determined by the tree structure of files  
produced by analyzing of the disc.  
• A disc with a mixed CD format will be  
recognized as a CD-DA (audio) disc.  
8GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Getting Started  
Hooking up the system  
Perform the following procedures 1 to 4 to hook up your system using the supplied cords and  
accessories.  
Right speaker  
Left speaker  
3
4
1
2
AM loop aerial  
FM lead aerial  
1 Connect the speakers.  
2 Connect the FM and AM aerials.  
Connect the right and left speaker cords to  
the SPEAKER terminals as shown below.  
Set up the AM loop aerial, then connect it.  
ANCE  
IMPED  
USE 6-16  
Red (3)  
3
Plug type A  
L
#
AM loop aerial  
#
R
Black (#)  
Insert this portion  
3
Extend the FM lead aerial  
horizontally  
continued  
9GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Plug type B  
4 Connect the mains lead to mains.  
If the plug does not fit the wall socket,  
detach the supplied plug adaptor (only for  
models equipped with an adaptor).  
To turn on the system, press ?/1.  
AM loop aerial  
Extend the FM lead aerial horizontally  
Plug type C  
AM loop aerial  
North American models:  
Connect using the white side  
Extend the FM lead  
aerial horizontally  
Other models:  
Connect using the brown  
side  
Note  
To prevent noise pickup, keep the aerials away from  
the speaker cords.  
3 For models with a voltage selector, set  
VOLTAGE SELECTOR to the local  
power line voltage.  
Refer to the print on your system’s  
VOLTAGE SELECTOR for available  
settings.  
10GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Inserting two R6 (size AA)  
batteries into the remote  
Setting the clock  
Use buttons on the remote for the operation.  
1
2
3
Press ?/1 to turn on the system.  
Press CLOCK/TIMER SET.  
Press . or > repeatedly to set the  
hour.  
4
5
Press ENTER.  
Press . or > repeatedly to set the  
minute.  
Note  
If you do not use the remote for a long period of time,  
remove the batteries to avoid possible damage from  
battery leakage and corrosion.  
6
Press ENTER.  
The clock starts working.  
Tip  
To adjust the clock  
With normal use, the batteries should last for about six  
months. When the remote no longer operates the  
system, replace both batteries with new ones.  
1 Press CLOCK/TIMER SET.  
2 Press . or > repeatedly to select  
“CLOCK SET”, then press ENTER.  
When carrying this system  
3 Do the same procedures as step 3 to 6  
above.  
Perform the following procedure to protect  
the CD mechanism.  
Note  
Use buttons on the unit for the operation.  
The clock is not displayed in Power Saving Mode  
1 Press ?/1 to turn on the system, then  
press FUNCTION repeatedly to switch  
the function to CD.  
2 Make sure that no disc is loaded in the  
disc slot.  
3 Hold down DISPLAY, and then press Z  
and ML until “LOCK” appears.  
4 Unplug the mains lead.  
11GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Playing a disc  
— Normal Play/Shuffle Play  
CD – Play  
Loading a disc  
Use buttons on the unit for the operation.  
This system lets you play CDs in different play  
modes.  
Example: When playing a disc  
1
2
Press CD (or FUNCTION repeatedly) to  
switch the function to CD.  
Insert a disc in the disc slot with the  
label side up.  
Z
Playing time  
Track number  
When you  
play a disc,  
insert it with  
the label side  
up.  
1
2
Press CD (or FUNCTION repeatedly) to  
switch the function to CD.  
Press PLAY MODE repeatedly in stop  
mode until the mode you want appears  
in the display.  
Notes  
Select  
To play  
• When you turn on the system, the disc is not  
pulled into the disc slot until “NO DISC”  
appears in the display. Do not attempt to  
push in the disc until “NO DISC” appears.  
• Do not use a disc with tape, seals or paste on it as this  
may cause malfunction.  
No display  
(Normal Play)  
The tracks on the disc in  
original order.  
All the tracks in the group on  
the ATRAC CD or MP3 CD  
in original order.  
(Normal Play)  
• Do not load an 8 cm disc with an adaptor. Doing so  
may cause the system to malfunction.  
• When you remove a disc, handle the disc by its edge  
and pull it straight out of the disc slot. Do not touch  
the surface.  
When playing an audio CD,  
the system performs the  
same operation as Normal  
Play.  
SHUF  
(Shuffle Play)  
All the tracks on the disc in  
random order.  
• If you load a disc that is not playable by this system,  
it will be ejected automatically.  
SHUF  
(Shuffle Play)  
All the tracks in the group on  
the ATRAC CD or MP3 CD  
in random order.  
When playing an audio CD,  
the system performs the  
same operation as Shuffle  
Play.  
PGM  
(Program Play)  
The tracks on the disc in the  
order you want them to be  
3
Press N (or CD NX on the unit).  
12GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Other operations  
Searching for tracks with  
the jog dial  
To  
Do this  
Stop play  
Pause  
Press x (or CD x on the unit).  
Press X (or CD NX on the unit).  
Press again to resume play.  
You can quickly search for and play the desired  
track by using the jog dial on the unit.  
Use buttons on the unit for the operation.  
Select a track  
Press . or > repeatedly.  
Select a group on Press  
the ATRAC CD step 2.  
or MP3 CD  
+ or – repeatedly after  
1
2
Press FUNCTION repeatedly to switch  
the function to CD.  
Find a point in a Keep pressing m or M during  
track  
playback and release it at the  
desired point.  
Turn the jog dial in stop mode to select  
the desired track, then press ENTER.  
Remove a disc Press Z on the unit.  
To search for tracks on the ATRAC CD or  
MP3 CD, turn the jog dial to first select the  
desired group, then press ENTER before  
performing step 2.  
Notes  
• You cannot change the play mode during playback.  
• Some time may be needed to start playback of discs  
recorded in complex configurations such as many  
layers.  
Playback starts from the selected track.  
Note  
• Before playing back a track, the system reads all  
tracks and groups on the disc. During this time,  
“READING” appears on the display. Depending on  
disc content, some time may be needed to read the  
disc.  
Only the first 6 characters are displayed when  
performing the group or track search.  
Tip  
You can search for and play other tracks in the selected  
group during playback. To select a track of another  
group during playback, turn the jog dial  
counterclockwise until “GROUP” appears, then press  
ENTER to select a group. You can then select the  
desired track by turning the jog dial.  
• A group that does not include MP3 tracks is skipped.  
• Depending on the encoding/writing software,  
recording device or the recording media used at the  
time an MP3 track is recorded, you may encounter  
such problems as disabled playback, sound  
interruptions and noise.  
To cancel the track search  
• When playing back an MP3 track, the playback  
elapsed time indication may differ from the actual  
time in the following cases.  
Press CANCEL.  
Notes  
– When you play back a VBR (variable bit rate)  
MP3 track  
• If you do not perform any operations for  
approximately 8 seconds, the display returns to the  
previous one.  
– When you perform fast forward or rewind (Manual  
Search)  
• The track search is not possible in Program Play  
mode.  
Tip  
When disc access takes a long time, set “CD POWER”  
and “ON” by CD power manage function (page 17).  
13GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
Playing repeatedly  
— Repeat Play  
Creating your own  
program  
— Program Play  
You can play all the tracks or a single track on a  
disc repeatedly.  
You can make a program of up to 25 steps.  
You can synchro record the programmed tracks  
onto a cassette tape (page 20).  
Press REPEAT repeatedly during playback  
until “REP” or “REP 1” appears.  
REP: For all the tracks on the disc up to five  
times.  
REP 1: For a single track only.  
Using the remote  
1
2
3
Press CD (or FUNCTION repeatedly) to  
switch the function to CD.  
To cancel Repeat Play  
Press REPEAT repeatedly until both “REP” and  
“REP 1” disappear.  
Press PLAY MODE repeatedly in stop  
mode until “PGM” appears.  
Note  
Press . or > repeatedly until the  
desired track number appears.  
When you select “REP 1”, that track is repeated  
endlessly until “REP 1” is canceled.  
When programming the tracks on the  
ATRAC CD or MP3 CD, press  
+ or –  
repeatedly to select the desired group, then  
press . or > repeatedly until the  
desired track number appears.  
Selected track number  
Total playing time  
4
Press ENTER.  
The track is programmed.  
The program step number appears,  
followed by the last programmed track  
number and total playing time.  
5
6
To program additonal tracks, repeat  
steps 3 and 4.  
Press N (or CD NX on the unit).  
Program Play starts.  
14GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
Other operations  
Using the jog dial  
To  
Do this  
Use buttons on the unit for the operation.  
Cancel Program Play  
Press PLAY MODE  
repeatedly in stop mode  
until “PGM” disappears.  
1
2
3
Press FUNCTION repeatedly to switch  
the function to CD.  
Erase the program  
Press CLEAR in stop  
mode. Each time you press  
the button, a track is cleared  
from the end of the  
program.  
Press PLAY MODE repeatedly in stop  
mode until “PGM” appears.  
Turn the jog dial to select the desired  
track.  
Add a track to the end of Perform steps 3 and 4 in  
To program tracks on the ATRAC CD or  
MP3 CD, turn the jog dial to first select the  
desired group, then press ENTER before  
performing step 3.  
the program  
stop mode.  
Note  
You cannot erase the program during playback.  
Tips  
4
Press ENTER.  
• You can program the tracks during playback by using  
the jog dial.  
The track is programmed.  
The program step number appears,  
followed by the last programmed track  
number and total playing time.  
• The program you made remains after Program Play  
finishes. To play the same program again, press CD  
(or FUNCTION repeatedly) to switch the function to  
CD, then press N (or CD NX on the unit).  
However, the program is cleared when you eject the  
disc.  
5
6
To program additional tracks, repeat  
steps 3 and 4.  
Press CD NX.  
• “– –.– –” appears when the total program time  
exceeds 100 minutes, or when you select a disc with  
21 tracks or more, or when you select an  
ATRAC3plus/MP3 track.  
Program Play starts.  
15GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
6
Press + or – (or TUNING + or – on the  
unit) repeatedly to select the desired  
preset number.  
Tuner  
7
8
Press ENTER.  
Presetting radio stations  
Repeat steps 4 through 7 to store other  
stations.  
You can preset up to 20 FM stations and 10 AM  
stations. You can then tune in any of those  
stations simply by selecting the corresponding  
preset number.  
Tip  
Press x to stop scanning.  
Manual tuning preset  
Automatic tuning preset  
You can manually tune in and store the radio  
frequency of the desired stations.  
You can automatically tune in all of the stations  
that can be received in your area and then store  
the radio frequency of the desired stations.  
1
Press TUNER BAND (or FUNCTION  
repeatedly) to switch the function to  
TUNER.  
1
Press TUNER BAND (or FUNCTION  
repeatedly) to switch the function to  
TUNER.  
2
3
Press TUNER BAND repeatedly to  
select “FM” or “AM”.  
2
3
4
Press TUNER BAND repeatedly to  
select “FM” or “AM”.  
Press TUNING MODE repeatedly until  
“AUTO” and “PRESET” disappear from  
the display.  
Press TUNING MODE repeatedly until  
“AUTO” appears in the display.  
4
Press + or – (or TUNING + or – on the  
unit) repeatedly to tune in the desired  
station.  
Press + or – (or TUNING + or – on the  
unit).  
The frequency changes as the system scans  
for a station. Scanning stops automatically  
when a station is tuned in. At that time,  
“TUNED” and “STEREO” (for an FM  
stereo program only) appear.  
5
6
Press TUNER MEMORY.  
Press + or – (or TUNING + or – on the  
unit) repeatedly to select the desired  
preset number.  
7
8
Press ENTER.  
If “TUNED” does not appear and the  
scanning does not stop  
Repeat steps 4 through 7 to store other  
stations.  
Set the frequency of the desired radio  
station as described in steps 3 and 4 of  
Other operations  
To  
Do this  
5
Press TUNER MEMORY.  
Tune in a station  
with a weak signal in “Manual tuning preset” .  
Follow the procedure described  
The preset number flashes. Perform steps 6  
and 7 while the preset number flashes.  
Set another station After step 5, press + or – (or  
to the existing  
preset number  
TUNING + or – on the unit)  
repeatedly to select the preset  
number of the station you want  
to store.  
Preset number  
16GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
To change the AM tuning interval  
(except for European model)  
Listening to the radio  
The AM tuning interval is factory-preset to  
9 kHz (or 10 kHz for some areas). To change the  
AM tuning interval, tune in any AM station first,  
then turn off the system. While holding  
ML, press ?/1 on the unit. When you  
change the interval, all the AM preset stations  
are erased. To reset the interval, repeat the same  
procedure.  
You can listen to a radio station either by  
selecting a preset station, or by manually tuning  
in the station.  
Listening to a preset station  
— Preset Tuning  
Note  
Preset radio stations in the tuner’s memory first  
You cannot change the AM tuning interval in Power  
Saving Mode (page 24).  
1
Press TUNER BAND (or FUNCTION  
repeatedly) to switch the function to  
TUNER.  
Tips  
• The preset stations are retained for about half a day  
even if you disconnect the mains lead or if a power  
failure occurs.  
2
3
4
Press TUNER BAND repeatedly to  
select “FM” or “AM”.  
• To improve broadcast reception, adjust the supplied  
aerials, or connect a commercially available external  
aerial.  
Press TUNING MODE repeatedly until  
“PRESET” appears in the display.  
To improve tuner reception  
Press + or – (or TUNING + or – on the  
unit) repeatedly to select the desired  
preset station.  
When tuner reception is poor, set CD player  
power off by CD power manage function.  
CD power is factory set to on.  
Use buttons on the unit for the operation.  
1 Press FUNCTION repeatedly to switch the  
function to CD.  
2 Press ?/1 to turn off the system.  
3 After “STANDBY” stops flashing, press ?/1  
while holding CD x.  
“CD POWER” and “OFF” appear.  
To set CD power on  
Repeat the procedure above and “CD POWER”  
and “ON” appear.  
Notes  
• When “CD POWER” and “OFF” are selected, disc  
access time is increased.  
• You cannot change the setting in Power Saving  
Mode (page 24).  
continued  
17GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
Listening to non-preset radio  
station  
Using the Radio Data  
System (RDS)  
— Manual Tuning  
(European model only)  
1
Press TUNER BAND (or FUNCTION  
repeatedly) to switch the function to  
TUNER.  
What is the Radio Data  
System?  
2
3
Press TUNER BAND repeatedly to  
select “FM” or “AM”.  
Radio Data System (RDS) is a broadcasting  
service that allows radio stations to send  
additional information along with the regular  
program signal. RDS is available only on FM  
stations.*  
Press TUNING MODE repeatedly until  
“AUTO” and “PRESET” disappear from  
the display.  
4
Press + or – (or TUNING + or – on the  
unit) repeatedly to tune in the desired  
station.  
Note  
RDS may not work properly if the station you are tuned  
in is not transmitting the RDS signal properly or if the  
signal is weak.  
Note  
When switching to CD function from tuner, a longer  
time may be required to access the disc. In this case, set  
“CD POWER” and “ON” by CD power manage  
function (page 17).  
* Not all FM stations provide RDS service, nor do they  
provide the same types of services. If you are not  
familiar with the RDS system, check with your local  
radio stations for details on RDS services in your  
area.  
Tips  
• To improve broadcast reception, adjust the supplied  
aerials, or connect a commercially available external  
aerial.  
Receiving RDS broadcasts  
• When an FM stereo program has static noise, press  
FM MODE repeatedly until “MONO” appears.  
There will be no stereo effect, but the reception will  
improve.  
Simply select a station from the FM band.  
When you tune in a station that provides RDS  
services, the station name appears in the display.  
• Press TUNING MODE repeatedly until “AUTO”  
appears in step 3 above, then press + or – (or  
TUNING + or – on the unit). The frequency  
indication changes and scanning stops when the  
system tunes in a station (Automatic Tuning).  
• To record the radio programs, use manual recording  
To check the RDS information  
Each time you press DISPLAY, the display  
changes cyclically as follows:  
Station name1) t Preset number2) and  
frequency t Clock display (for eight seconds)  
t Bass level (for eight seconds) t Treble  
level (for eight seconds)  
1) If the RDS broadcast is not properly received, the  
station name may not appear in the display.  
2) Preset number is displayed only if you preset radio  
stations (page 16).  
18GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Playing a tape  
Tape – Play  
You can use TYPE I (normal) tape.  
Loading a tape  
1
2
Load a tape.  
1
Press Z PUSH OPEN/CLOSE on the  
unit.  
Press TAPE (or FUNCTION repeatedly)  
to switch the function to TAPE.  
2
Load a recorded/recordable tape into  
the cassette holder.  
3
Press N (or TAPE N on the unit).  
Other operations  
Note  
To  
Do this  
Be careful not to touch the exposed tape.  
Stop play  
Pause  
Press x (or TAPE x on the unit).  
Press X. Press again to resume  
play.  
With the side  
you want to  
play/record  
facing towards  
you.  
Fast-forward or  
rewind  
Press m or M.  
Remove a tape  
Press Z PUSH OPEN/CLOSE  
on the unit in stop mode.  
H
s
j
J
Note  
Do not eject the tape during playback or recording, as  
this may cause irreparable damage to the tape and  
cassette holder.  
19GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
Recording on a tape  
manually  
Tape – Recording  
Recording your favorite  
CD tracks on a tape  
— Manual Recording  
You can record just the portions you like from a  
CD or radio program on a tape.  
— CD-TAPE Synchro Recording  
You can also record from connected  
You can use TYPE I (normal) tape. The  
recording level is adjusted automatically.  
Use buttons on the unit for the operation.  
Use buttons on the unit for the operation.  
1
2
Load a recordable tape.  
1
2
Load a recordable tape.  
Press FUNCTION repeatedly to switch  
the function to CD and load a disc you  
want to record.  
Press FUNCTION repeatedly to select  
the desired source to record.  
• CD: To record from this system’s CD  
player.  
• TUNER: To record from this system’s  
tuner.  
• MD: To record from the optional  
component connected to the ANALOG  
IN jack.  
When you want to record a group from an  
ATRAC CD or MP3 CD, be sure to press  
PLAY MODE repeatedly to select , then  
press  
+ or – repeatedly to select the  
desired group before proceeding.  
3
4
Press CD SYNC.  
“SYNC” and “REC” appear. The tape deck  
stands by for recording and the CD player  
pauses for playback.  
3
4
Press z PAUSE/START.  
“REC” lights up and the tape deck stands by  
for recording.  
Press z PAUSE/START.  
Press z PAUSE/START, then start  
playing the desired source to record.  
Recording starts.  
When the recording is completed, the CD  
player and the tape deck stop automatically.  
Recording starts.  
Other operations  
To stop recording  
Press TAPE x (or CD x).  
To  
Do this  
Stop recording  
Pause recording  
Press TAPE x.  
Tip  
Press z PAUSE/START.  
If you stop the recording by pressing CD x, the tape  
stops after making about a 4 seconds blank  
(unrecorded) space before stopping.  
Notes  
• You cannot listen to other sources while recording.  
• Recording stops if you change the function to another  
one.  
To record a disc by specifying  
track order  
You can record only your favorite CD tracks  
using Program Play. Between steps 2 and 3,  
perform steps 2 to 5 of “Creating your own  
Tip  
For recording from the tuner:  
If noise is heard while recording from the tuner, move  
the respective aerial to reduce the noise.  
20GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                           
Sound Adjustment  
Timer  
Adjusting the sound  
Falling asleep to music  
— Sleep Timer  
You can adjust the bass and treble to enjoy more  
powerful sound.  
You can set the system to turn off after a certain  
time, so that you can fall asleep to music.  
Generating a more dynamic  
sound (Dynamic Sound  
Generator X-tra)  
Press SLEEP repeatedly.  
Each time you press the button, the minute  
display (the turn-off time) changes cyclically as  
follows:  
AUTO* t 90MIN t 80MIN t t  
10MIN t SLEEP OFF  
Press DSGX on the unit.  
Each time you press the button, the display  
changes cyclically as follows:  
*
* The system automatically turns off in 100 minutes or  
after the current disc or tape finishes playing.  
DSGX ON y DSGX OFF  
* The DSGX indicator lights up.  
Other operations  
To  
Press  
Adjusting the bass and treble  
Check the  
remaining time*  
SLEEP once.  
You can adjust the bass and treble.  
1
Press EQ repeatedly to select “BASS”  
or “TREBLE”.  
Change the time SLEEP repeatedly to select the  
to turn off time you want.  
Cancel the Sleep SLEEP repeatedly until “SLEEP  
Timer function OFF” appears.  
Each time you press the button, the display  
changes as follows:  
BASS y TREBLE  
* You cannot check the remaining time if you select  
“AUTO”.  
2
Press . or > repeatedly to adjust  
the level while “BASS” or “TREBLE”  
appears.  
Tip  
You can use the Sleep Timer, even if you have not set  
the clock.  
To adjust the bass on the unit  
Turn BASS control.  
To adjust the treble on the unit  
Turn TREBLE control.  
To exit the bass and treble  
settings  
Press any button other than EQ, . or >.  
Also if you do not perform any operations for a  
few seconds, the display automatically returns to  
the original display.  
21GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
Other operations  
Waking up to music  
— Play Timer  
To  
Do this  
Activate the timer/ 1 Press CLOCK/TIMER  
check the setting  
SELECT.  
2 Press . or >  
repeatedly until “PLAY  
SEL” appears, then press  
ENTER.  
You can wake up to music at a preset time. Make  
sure you have set the clock (see “Setting the  
Use buttons on the remote for the operation.  
Change the setting Start over from step 1.  
1
Prepare the sound source you want to  
play.  
Cancel the timer  
1 Press CLOCK/TIMER  
SELECT.  
• CD: Load a disc. To start from a specific  
track, make a program (see “Creating  
• TUNER: Tune in the preset radio station  
2 Press . or >  
repeatedly until “TIMER  
OFF” appears, then press  
ENTER.  
Notes  
• You cannot activate the Play Timer and the Rec  
Timer at the same time.  
• If you use the Play Timer and the Sleep Timer at the  
same time, the Sleep Timer has priority.  
• Do not operate the system from the time the system  
turns on until the play starts (about 15 seconds before  
the preset time).  
2
Press VOLUME +/– to adjust the  
volume.  
3
4
Press CLOCK/TIMER SET.  
• If the system is on about 15 seconds before the preset  
time, the Play Timer will not be activated.  
• You cannot use the optional component connected to  
ANALOG IN jack as the sound source for Play  
Timer.  
Press . or > repeatedly to select  
“PLAY SET”, then press ENTER.  
“ON” appears and the hour indication  
flashes.  
5
Set the time to start playing.  
• The Play Timer setting remains as long as the setting  
is not canceled manually.  
Press . or > repeatedly to set the  
hour, then press ENTER.  
The minute indication flashes.  
Press . or > repeatedly to set the  
minute, then press ENTER.  
6
7
Set the time to stop playing following  
the same procedure as step 5.  
Press . or > repeatedly until the  
desired sound source appears.  
Each time you press the button, the display  
changes cyclically as follows:  
t
y
T
TUNER  
CD PLAY  
t
T
TAPE PLAY  
8
9
Press ENTER.  
The start time, the stop time and the sound  
source appear in turn, then the original  
display returns.  
Press ?/1 to turn off the system.  
22GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
Other operations  
Timer recording radio  
programs  
To  
Do this  
Activate the timer/ 1 Press CLOCK/TIMER  
check the setting  
SELECT.  
2 Press . or >  
repeatedly until “REC SEL”  
appears, then press ENTER.  
— Rec Timer  
You can record a preset radio station from a  
specified time.  
Change the setting Start over from step 1.  
To timer record, you must first preset the radio  
Cancel the timer  
1 Press CLOCK/TIMER  
SELECT.  
2 Press . or >  
repeatedly until “TIMER  
OFF” appears, then press  
ENTER.  
1
Tune in the preset radio station (see  
Notes  
• You cannot activate the Play Timer and the Rec  
Timer at the same time.  
2
3
Press CLOCK/TIMER SET.  
Press . or > repeatedly to select  
“REC SET”, then press ENTER.  
• If you use the Rec Timer and the Sleep Timer at the  
same time, the Sleep Timer has priority.  
• Do not operate the system from the time the system  
turns on until the recording starts (about 15 seconds  
before the preset time).  
“ON” appears and the hour indication  
flashes.  
4
5
Set the time to start recording.  
• If the system is on about 15 seconds before the preset  
time, the Rec Timer will not be activated.  
• The volume is reduced to minimum during  
recording.  
Press . or > repeatedly to set the  
hour, then press ENTER.  
The minute indication flashes.  
Press . or > repeatedly to set the  
minute, then press ENTER.  
• The Rec Timer is canceled automatically after the  
Rec Timer has been activated.  
Set the time to stop recording following  
the same procedure as step 4.  
The start time, the stop time, and the preset  
radio station to be recorded (e.g., “FM 5”)  
appear in turn, before the original display  
returns.  
6
7
Load a recordable tape.  
Press ?/1 to turn off the system.  
23GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Viewing information  
about the disc in the  
display  
Display  
Turning off the display  
— Power Saving Mode  
You can check the playing time and remaining  
time of the current track or that of the disc.  
When an ATRAC CD or MP3 CD is loaded, you  
can also check the information recorded on disc,  
such as the titles.  
The clock display can be turned off to minimize  
the amount of power consumed during standby  
(Power Saving Mode).  
Press DISPLAY repeatedly while the  
system is off until the clock display  
disappears.  
Checking the remaining time  
and titles  
To cancel Power Saving Mode  
Press DISPLAY while the system is off. Each  
time you press the button, the display switches  
cyclically as follows:  
Clock display* t No display (Power Saving  
Mode)  
Press DISPLAY during Normal Play.  
Each time you press the button, the display  
changes cyclically as follows:  
Current track number and elapsed playing time  
t Current track number and remaining time or  
“– –.– –”1) t Remaining time of the disc or  
“– –.– –”2) t Track title (ATRAC CD and MP3  
CD4) only) t Group name3)4) t Clock display  
(for eight seconds) t Bass level (for eight  
seconds) t Treble level (for eight seconds)  
* The clock is displayed only if you set the clock.  
Note  
You cannot perform the following operations in Power  
Saving Mode.  
– setting the clock  
1)  
– changing the AM tuning interval (except for  
European model)  
For MP3 CDs  
2)  
“– –.– –” appears for ATRAC CDs, MP3 CDs or  
– changing the CD power manage function  
when the audio CD is in a play mode other than 1  
DISC Play.  
Tips  
3)  
For ATRAC CDs and MP3 CDs  
• STANDBY indicator lights up even in Power Saving  
Mode.  
4)  
When you play back a track with an ID3 tag ver. 1  
or ver. 2, the ID3 tag information appears. The ID3  
tag displays the track title, album name and artist  
name information.  
• The timer continues to operate in Power Saving  
Mode.  
Note  
When fast forward or fast reverse is performed, elapsed  
playing time and remaining time of the track may not  
be displayed accurately.  
24GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Checking the total playing  
time and titles  
Viewing the tuner  
information in the display  
Press DISPLAY repeatedly in stop mode.  
Each time you press the button, the display  
changes cyclically as follows:  
Press DISPLAY while listening to the radio.  
Each time you press the button, the display  
changes cyclically as follows:  
Station name1) t Preset number2) and  
frequency t Clock display (for eight seconds)  
t Bass level (for eight seconds) t Treble  
level (for eight seconds)  
x Normal Play mode  
TOC display1) or total group number of the disc2)  
or total track number of the current group2) t  
Volume label2) or group name2) t Clock  
display (for eight seconds) t Bass level (for  
eight seconds) t Treble level (for eight  
seconds)  
1) European model only  
2) Preset number is displayed only if you preset radio  
stations (page 16)  
1) TOC = Table of Contents; displays total number of  
tracks on the disc, and total playing time of the disc  
2) For ATRAC CDs and MP3 CDs (group names or  
volume label may not be displayed depending on the  
play mode)  
x Program Play mode  
The last track number of the program and the  
total playing time t Total track number of the  
program t Volume label* t Clock display  
t Bass level t Treble level  
* For ATRAC CDs and MP3 CDs  
25GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Optional Components  
Hooking up optional components  
To enhance your system, you can connect optional components. Refer to the operating instructions  
provided with each component.  
H
s
j
J
+
/
1
s
lj JL  
HS  
A
From the audio output jacks of an  
optional analog component  
To the digital input jack of an  
optional digital component  
Optional analog component  
Optional digital component  
Notes  
A ANALOG IN jack  
• There is no digital audio output from this jack during  
playback of ATRAC3plus/MP3 tracks.  
Use audio cord (not supplied) to connect an  
optional analog component (MiniDisc player/  
recorder or Portable Audio player, etc.) to this  
jack. You can then record or listen to the sound  
from the component through this system.  
• You cannot make a digital recording of a copy  
guarded disc using a digital component connected to  
this system. Also, playback may not be possible  
depending on the connected component.  
• Before connecting or disconnecting the audio cord  
(not supplied), press VOLUME – repeatedly (or turn  
the VOLUME control on the unit counterclockwise)  
to turn down the volume.  
B CD DIGITAL OUT jack  
Use a digital optical cord (square, not supplied)  
to connect an amplifier, MiniDisc player/  
recorder or DAT deck with a digital optical input  
jack. Sound is then output when the system  
function is set to CD. If the jack is covered with  
a cap, remove it before use.  
26GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Listening to audio from a  
connected component  
Recording on a connected  
component  
1
Connect the audio cord (not supplied).  
1
Connect the digital optical cord.  
2
Start recording with the connected  
digital component (MiniDisc player/  
recorder, etc.).  
2
3
Press FUNCTION repeatedly until “MD”  
appears.  
Refer to the operating instructions provided  
with the connected component.  
Start playing the connected  
component.  
Note  
You can digitally record from the discs only. However,  
you cannot record from copy prohibited discs and  
ATRAC3plus/MP3 tracks.  
Recording audio from a  
connected component  
1
Connect audio cord (not supplied).  
2
Start recording manually.  
27GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
General  
“– –:– –” appears in the display.  
• A power interruption has occurred. Set the clock  
(page 11) and timer settings (pages 22 and 23)  
again.  
Troubleshooting  
Problems and remedies  
The clock setting/radio presetting/timer is  
canceled.  
• Redo the following:  
Should you encounter a problem with your  
system, do the following:  
1 Make sure the mains lead and speaker  
cords are correctly and firmly connected.  
2 Find your problem in the troubleshooting  
checklist below and take the indicated  
corrective action.  
There is no sound.  
• Press VOLUME + or turn VOLUME control on  
the unit clockwise.  
If the problem persists after doing all of the  
above, consult your nearest Sony dealer.  
• Make sure the headphones are not connected.  
• Check the speaker connections (page 9).  
• There is no audio output during Rec Timer.  
When the STANDBY indicator  
flashes  
Sound comes from one channel, or  
unbalanced left and right volume.  
• Place the speakers as symmetrically as possible.  
• Connect the supplied speakers.  
Immediately unplug the mains lead and check  
the following items.  
• If your system has a voltage selector, is the  
voltage selector set to the correct voltage?  
Check the voltage for your region, then  
make sure the voltage selector is set  
correctly.  
• Are the + and – speaker cords short-  
circuited?  
• Are you using the supplied speakers?  
• Is anything blocking the ventilation holes  
on the rear of the system?  
There is severe hum or noise.  
• Move the system away from the source of noise.  
• Connect the system to a different mains.  
• Install a noise filter (commercially available) to  
the mains lead.  
The timer cannot be set.  
• Set the clock again (page 11).  
The timer does not function.  
• Check the timer setting and set the correct time  
(pages 22 and 23).  
Check all the above items and fix any  
problems found. After STANDBY indicator  
stops flashing, reconnect the mains lead and  
turn on the system. If the indicator still  
flashes, or if the cause of the problem cannot  
be found even after checking all the above  
items, consult your nearest Sony dealer.  
• Cancel the Sleep Timer function (page 21).  
• Make sure the clock is correctly set (page 11).  
The color irregularity on a TV screen persists.  
• Turn off the TV set once, then turn it on after 15  
to 30 minutes. If the color irregularity still  
persists, place the speakers farther away from the  
TV set.  
28GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
The remote does not function.  
• Remove the obstacle.  
Tracks on the ATRAC CD or MP3 CD cannot be  
played back.  
• Recording was not performed according to the  
ISO9660 Level 1 or Level 2 format, or Joliet in the  
expansion format.  
• Move the remote closer to the system.  
• Point the remote at the system’s sensor.  
• Replace the batteries (R6/size AA).  
• Locate the system away from the fluorescent light.  
• The MP3 file does not have the extension “.MP3”.  
• The data is not stored in ATRAC3plus/MP3  
format.  
The system can not be turned on even though  
you have pressed ?/1.  
• Make sure the mains lead is connected to mains.  
• Discs containing MP3 files other than MPEG 1, 2,  
2.5 Audio Layer-3 files cannot be played.  
Tracks on the ATRAC CD or MP3 CD take  
longer to play back than others.  
• After the system reads all tracks on the disc,  
playback may take more time than usual if:  
– the number of groups or tracks on the disc is  
very large.  
CD player  
“LOCKED” appears.  
• Contact your Sony dealer or local authorized Sony  
service facility.  
– the album and track organization structure is  
very complex.  
The disc does not eject.  
• You cannot eject the disc during CD Synchro  
Recording. Press CD x on the unit to cancel the  
CD Synchro Recording, then press Z on the unit  
to eject the disc.  
Title information do not appear correctly.  
• Use a disc that conforms with ISO9660 Level 1,  
Level 2 or Joliet in the expansion format.  
• The disc ID3 tag is not ver. 1 nor ver. 2.  
• The characters that can be displayed by this  
system are as follows:  
• Consult your nearest Sony dealer.  
Play does not start.  
• Check whether a disc is loaded.  
– Upper cases (A to Z)  
• Wipe the disc clean (page 32).  
– Numbers (0 to 9)  
• Replace the disc.  
– Symbols (’< > * + , – /@[\] _ `)  
• Load the disc that this system can play (page 6).  
• Load the disc correctly.  
Other characters may not be displayed correctly.  
• Load the disc with the label side up.  
• Remove the disc and wipe away the moisture on  
the disc, then leave the system turned on for a few  
hours until the moisture evaporates.  
• Press N (or CD NX on the unit) to start play.  
Disc access takes a long time.  
• Set “CD POWER” and “ON” by CD power  
manage function (page 17).  
The sound skips.  
• Wipe the disc clean (page 32).  
• Replace the disc.  
• Try moving the system to a place without  
vibration (e.g., on top of a stable stand).  
• Try moving the speakers away from the system, or  
placing them on separate stands. When you listen  
to a track with bass sounds at high volume, the  
speaker vibration may cause the sound to skip.  
Play does not start from the first track.  
• Press PLAY MODE repeatedly until both “PGM”  
and “SHUF” disappear to return to Normal Play.  
continued  
29GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Tuner  
The tape does not record.  
• No cassette is loaded. Load a cassette.  
• The tab has been removed from the cassette.  
Cover the broken tab with adhesive tape  
Severe hum or noise/stations cannot be  
received.  
• Set the proper band and frequency (page 16).  
• Connect the aerial properly (page 9).  
• Find a place and an orientation that provide good  
reception, then set up the aerial again. If you  
cannot obtain good reception, we recommend you  
connect a commercially available external aerial.  
• The supplied FM lead aerial receives signals  
along its entire length, so make sure you extend it  
fully.  
• The tape has wound to the end.  
Optional components  
There is no sound.  
• Refer to General item “There is no sound.”  
(page 28) and check the condition of the system.  
• Connect the component properly (page 26) while  
checking:  
• Locate the aerials as far away from the speaker  
cords as possible.  
• Consult your nearest Sony dealer if the supplied  
AM aerial has come off the plastic stand.  
• Try turning off surrounding electrical equipment.  
• Set “CD POWER” and “OFF” by CD power  
manage function (page 17).  
– if the cords are connected properly.  
– if the cord plugs are firmly inserted all the way.  
• Turn on the connected component.  
• Refer to the operating instructions supplied with  
the connected component and start playing.  
• Press FUNCTION repeatedly to select “MD”  
A stereo FM program cannot be received in  
stereo.  
• Press FM MODE until “STEREO” appears in the  
display.  
The sound is distorted.  
• Set the volume of the connected component  
lower.  
Tape deck  
If the system still does not  
operate properly after performing  
the above measures, reset the  
system as follows:  
The tape does not record or play, or there is a  
decrease in sound level.  
• The heads are dirty. Clean them (page 33).  
• The record/playback heads are magnetized.  
Demagnetize them (page 33).  
Use buttons on the unit for the operation.  
The tape does not erase completely.  
• The record/playback heads are magnetized.  
Demagnetize them (page 33).  
1 Disconnect the mains lead.  
2 Reconnect the mains lead.  
3 Press ?/1 to turn on the system.  
4 Press CD x, DISPLAY and ?/1.  
The system is reset to the factory settings. You  
should set the settings you made, such as the  
preset stations, clock, and timer.  
There is excessive wow or flutter, or the sound  
drops out.  
• The capstans in the tape deck are dirty. Clean  
Noise increases or the high frequencies are  
erased.  
• The record/playback heads are magnetized.  
Demagnetize them (page 33).  
30GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Messages  
One of the following messages may appear or  
flash in the display during operation.  
CD  
NO DISC  
There is no disc in the player.  
NO STEP  
All of the programmed tracks have been erased.  
CD OVER  
You have reached the end of the disc while pressing  
M during playback or pause.  
PUSH STOP  
You pressed PLAY MODE during playback.  
STEP FULL  
You tried to program 25 or more tracks (steps).  
Tuner  
COMPLETE  
The preset operation ended normally.  
Tape  
NO TAB  
You cannot record the tape because the tab has been  
removed from the cassette.  
NO TAPE  
There is no tape in the tape deck.  
Timer  
PUSH SELECT  
You tried to set the clock or timer during timer  
operation.  
SET CLOCK  
You tried to select the timer when the clock is not  
set.  
SET TIMER  
You tried to select the timer when the Play Timer or  
Rec Timer are not set.  
TIME NG  
The Play Timer or Rec Timer start and end times are  
set to the same time.  
31GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
On the speaker system  
This speaker system is not magnetically shielded and  
the picture on TV sets may become magnetically  
distorted. In such a case, turn off the power of the TV  
set once, and after 15 to 30 minutes turn it on again.  
If there seems to be no improvement, locate the  
speaker system further away from the TV set.  
Additional Information  
Precautions  
On operating voltage  
Before operating the system, check that the operating  
voltage of your system is identical with the voltage of  
your local power supply.  
On operation  
• If the system is brought directly from a cold to a  
warm location, or is placed in a very damp room,  
moisture may condense on the lens inside the CD  
player. Should this occur, the system will not operate  
properly. Remove the disc and leave the system  
turned on for about an hour until the moisture  
evaporates.  
On safety  
• The unit is not disconnected from the AC power  
source (mains) as long as it is connected to the wall  
outlet, even if the unit itself has been turned off.  
• Unplug the system from the wall outlet (mains) if it  
is not to be used for an extended period of time. To  
disconnect the power cord (mains lead), pull it out by  
the plug. Never pull the cord itself.  
• When you move the system, take out any disc.  
If you have any questions or problems concerning your  
system, please consult your nearest Sony dealer.  
• Should any solid object or liquid fall into the system,  
unplug the system and have it checked by qualified  
personnel before operating it any further.  
Notes on discs  
• Before playing, clean the disc with a cleaning cloth.  
• AC power cord must be changed only at the qualified  
service shop.  
Wipe the disc from the center out.  
• Do not use solvents such as benzine, thinner,  
commercially available cleaners or anti-static spray  
intended for vinyl LPs.  
On placement  
• Do not place the system in an inclined position.  
• Do not place the system in locations where it is;  
– Extremely hot or cold  
• Do not expose the disc to direct sunlight or heat  
sources such as hot air ducts, nor leave it in a car  
parked in direct sunlight.  
– Dusty or dirty  
• Do not use discs encircled with a protection ring.  
This may cause a malfunction to the system.  
• When using discs that have glue or similar tacky  
substance on the label side of the disc or that used a  
special ink when the label was printed, there is a  
chance that the disc or label may become attached to  
parts inside this unit. When this occurs, it may not be  
possible to remove the disc, and may also cause this  
unit to malfunction. Be sure to check that the label  
side of the disc is not sticky before using.  
– Very humid  
– Subject to vibrations  
– Subject to direct sunlight  
• Use caution when placing the unit or speakers on  
surfaces that have been specially treated (with wax,  
oil, polish, etc.) as staining or discoloration of the  
surface may result.  
On heat buildup  
• Although the system heats up during operation, this  
is not a malfunction.  
The following types of disc should not be used:  
– Rental or used discs with attached seals where the  
glue extends beyond the seal. The perimeter of the  
seal on the disc is tacky.  
• Place the system in a location with adequate  
ventilation to prevent heat build-up in the system.  
• If you continuously use this system at a high volume,  
the cabinet temperature of the top, side and bottom  
rises considerably. To avoid burning yourself, do not  
touch the cabinet.  
– Discs that have labels printed using a special ink  
that feels tacky when touched.  
• Discs with non-standard shapes (e.g., heart, square,  
star) cannot be played on this unit. Attempting to do  
so may damage the unit. Do not use such discs.  
• To prevent a malfunction, do not cover the  
ventilation hole.  
Cleaning the cabinet  
Clean the cabinet, panel and controls with a soft cloth  
slightly moistened with mild detergent solution. Do not  
use any type of abrasive pad, scouring powder or  
solvent such as thinner, benzine or alcohol.  
32GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
To save a tape permanently  
To prevent a tape from being accidentally recorded  
over, break off the cassette tab from side A or B as  
illustrated.  
Specifications  
Main unit (HCD-GPZ7/HCD-GPZ6)  
Amplifier section  
Break off the  
cassette tab  
HCD-GPZ7 for CMT-GPZ7  
European model:  
DIN power output (rated): 40 + 40 W (6 ohms at  
1 kHz, DIN)  
If you later want to reuse the tape for recording, cover  
the broken tab with adhesive tape.  
Continuous RMS power output (reference):  
60 + 60 W (6 ohms at  
1 kHz, 10% THD)  
Before placing a cassette in the tape  
deck  
Take up any slack in the tape. Otherwise, the tape may  
get entangled in the parts of the tape deck and become  
damaged.  
Music power output (reference):  
100 + 100 W (6 ohms at  
1 kHz, 10% THD)  
Other models:  
The following measured at AC 240 V, AC 220 V or AC  
120 V  
DIN power output (rated): 40 + 40 W  
(6 ohms at 1 kHz, DIN)  
Continuous RMS power output (reference):  
60 + 60 W  
When using a tape longer than  
90 minutes  
The tape is very elastic. Do not change the tape  
operations such as play, stop, and fast-winding  
frequently. The tape may get entangled in the tape  
deck.  
(6 ohms at 1 kHz, 10%  
THD)  
Cleaning the tape heads  
HCD-GPZ6 for CMT-GPZ6  
Clean the tape heads after every 10 hours of use.  
Be sure to clean the tape heads before you start an  
important recording or after playing an old tape.  
Use a separately sold dry-type or wet-type cleaning  
cassette. For details, refer to the instructions of the  
cleaning cassette.  
European model:  
DIN power output (rated): 40 + 40 W (6 ohms at  
1 kHz, DIN)  
Continuous RMS power output (reference):  
50 + 50 W (6 ohms at  
1 kHz, 10% THD)  
Music power output (reference):  
90 + 90 W (6 ohms at  
1 kHz, 10% THD)  
Demagnetizing the tape heads  
Demagnetize the tape heads and the metal parts that  
have contact with the tape after every 20 to 30 hours of  
use with a separately sold demagnetizing cassette. For  
details, refer to the instructions of the demagnetizing  
cassette.  
Other models:  
The following measured at AC 240 V, AC 220 V or AC  
120 V  
DIN power output (rated): 30 + 30 W  
(6 ohms at 1 kHz, DIN)  
Continuous RMS power output (reference):  
40 + 40 W  
(6 ohms at 1 kHz, 10%  
THD)  
Inputs  
ANALOG IN (stereo mini jack):  
Sensitivity 250 mV,  
impedance 47 kilohms  
Outputs  
CD DIGITAL OUT:  
Optical Wavelength:  
660 nm  
continued  
33GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
PHONES (stereo mini jack):  
SPEAKER:  
Other models:  
530 – 1,710 kHz  
(with the tuning interval  
set at 10 kHz)  
531 – 1,602 kHz  
(with the tuning interval  
set at 9 kHz)  
accepts headphones with  
an impedance of 8 ohms or  
more  
accepts impedance of 6 to  
16 ohms  
Aerial  
Aerial terminals  
Intermediate frequency  
AM loop aerial  
External aerial terminal  
450 kHz  
CD player section  
System  
Compact disc and digital  
audio system  
Laser Diode Properties  
Emission duration:  
continuous  
Laser Output*:  
Speaker (SS-CGPZ7/SS-CGPZ6)  
SS-CGPZ7 for CMT-GPZ7  
Speaker system  
Speaker units  
Woofer:  
Tweeter:  
Nominal impedance  
Dimensions (w/h/d)  
2-way, bass-reflex type  
Less than 44.6 µW  
* This output is the value measurement at a distance of  
200 mm from the objective lens surface on the  
Optical Pick-up Block with 7 mm aperture.  
13 cm dia., cone type  
4 cm dia., cone type  
6 ohms  
Approx. 163 × 261 ×  
260 mm  
Frequency response  
Wavelength  
20 Hz – 20 kHz ( 0.5 dB)  
780 – 790 nm  
Mass  
Approx. 2.9 kg net per  
speaker  
Tape deck section  
Recording system  
Frequency response  
4-track 2-channel stereo  
50 – 13,000 Hz ( 3 dB),  
using Sony TYPE I  
cassettes  
0.15% W. Peak (IEC)  
0.1% W. RMS (NAB)  
0.2% W. Peak (DIN)  
SS-CGPZ6 for CMT-GPZ6  
Speaker system  
Speaker units  
Woofer:  
Tweeter:  
Nominal impedance  
Dimensions (w/h/d)  
2-way, bass-reflex type  
Wow and flutter  
12 cm dia., cone type  
4 cm dia., cone type  
6 ohms  
Approx. 163 × 261 ×  
230 mm  
Tuner section  
FM stereo, FM/AM superheterodyne tuner  
Mass  
Approx. 2.5 kg net per  
speaker  
FM tuner section  
Tuning range  
Aerial  
Aerial terminals  
Intermediate frequency  
87.5 – 108.0 MHz  
FM lead aerial  
75 ohms unbalanced  
10.7 MHz  
General  
Power requirements  
European model:  
Korean model:  
Australian model:  
Argentine model:  
Mexican model:  
Other models:  
230 V AC, 50/60 Hz  
220 V AC, 60 Hz  
230 – 240 V AC, 50/60 Hz  
220 V AC, 50/60 Hz  
120 V AC, 60 Hz  
AM tuner section  
Tuning range  
Pan-American model:  
530 – 1,710 kHz  
(with the tuning interval  
set at 10 kHz)  
531 – 1,710 kHz  
(with the tuning interval  
set at 9 kHz)  
531 – 1,602 kHz  
(with the tuning interval  
set at 9 kHz)  
120 V, 220 V or  
230 – 240 V AC, 50/60 Hz  
Adjustable with voltage  
selector  
European model:  
34GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Power consumption  
CMT-GPZ7  
European model:  
100 W  
0.25 W (in Power Saving  
Mode)  
105 W  
105 W  
Mexican model:  
Other models:  
CMT-GPZ6  
European model:  
90 W  
0.25 W (in Power Saving  
Mode)  
75 W  
Other models:  
Dimensions (w/h/d) (excl. speakers)  
Approx. 181 × 261 ×  
297 mm  
Mass (excl. speakers)  
Amplifier/Tuner/Tape/CD section:  
CMT-GPZ7:  
CMT-GPZ6:  
6.1 kg  
5.8 kg  
Supplied accessories  
Remote Commander (1)  
R6 (Size AA) batteries (2)  
AM loop aerial (1)  
FM lead aerial (1)  
CD-ROM (SonicStage) (1)  
SonicStage Installation/  
Operating Guide (1)  
US and foreign patents licensed from Dolby  
Laboratories.  
Design and specifications are subject to change  
without notice.  
• Standby power consumption: 0.3 W  
• Halogenated flame retardants are not  
used in the certain printed wiring boards.  
• Lead-free solder is used for soldering  
certain parts.  
• Halogenated flame retardants are not  
used in cabinets.  
35GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
List of button locations and reference pages  
Illustration number  
How to use this page  
r
Use this page to find the location of buttons and other  
parts of the system that are mentioned in the text.  
TUNER/BAND qd (16, 17)  
R
R
Name of button/part Reference page  
Main unit  
BUTTON DESCRIPTIONS  
ALPHABETICAL ORDER  
?/1 (power) 1 (10, 17, 30)  
Z PUSH OPEN/CLOSE (tape  
open/close) 6 (19)  
TAPE N (play) 7 (19)  
x (tape stop) 8 (19, 20)  
m/M (tape rewind/fast  
forward) 9 (19)  
z PAUSE/START (record) qa  
+/– (select group) qh (13, 20)  
lm/ML (rewind/fast  
forward, go back/go forward)  
A – I  
J – Z  
ANALOG IN jack wf (20, 22, 26)  
BASS +/– ed (21)  
CANCEL wa (13)  
Cassette compartment 5 (19)  
CD DIGITAL OUT jack wd (26)  
CD SYNC qs (20)  
Disc slot ea (12)  
DISPLAY 3 (18, 24, 25)  
Display window 4  
DSGX ef (21)  
ENTER qk (13, 15)  
Jog dial qj (13, 15)  
PHONES jack e;  
PLAY MODE wk (12, 14, 20)  
Remote sensor q;  
REPEAT wj (14)  
TREBLE +/– es (21)  
TUNER/BAND qd (16, 17)  
TUNER MEMORY qf (16)  
TUNING MODE wg (16, 17)  
TUNING +/– qg (16, 17)  
VOLUME control 2  
FM MODE wh (18)  
FUNCTION wl (12, 14, 16, 17,  
19, 20, 27)  
Z (CD open/close) w; (13, 19)  
x (CD stop) wa (11, 17, 20)  
CD NX (play) ws (12)  
3
4
5 678 9  
H
s
j
J
0
qa  
qs  
qd  
qf  
qg  
qh  
2
1
ef  
ed  
es  
+
/
1
qj  
qk  
ql  
w;  
wa  
ws  
s
lj JL  
HS  
A
ea  
e; wlwkwjwhwg wf wd  
36GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Remote control  
ALPHABETICAL ORDER  
BUTTON DESCRIPTIONS  
A – E  
?/1 (power) 1 (11, 22)  
m/M (rewind/fast forward)  
7 (13, 19)  
N (play) 8 (12, 19)  
X (pause) 8 (13, 19)  
x (stop) 8 (13, 19)  
+/– (select group) qa (13, 14)  
./> (go back/go forward)  
F – Z  
CLEAR qd (15)  
CLOCK/TIMER SELECT 2  
CLOCK/TIMER SET 3 (11, 22,  
23)  
DISPLAY ql (18, 24, 25)  
ENTER 9 (11, 14, 16, 22, 23)  
EQ qs (21)  
FM MODE 4 (18)  
FUNCTION 6 (12, 14, 16, 17,  
PLAY MODE qk (12, 14, 20)  
REPEAT 4 (14)  
SLEEP w; (21)  
TAPE qg (19)  
TUNER BAND 5 (16, 17)  
TUNER MEMORY qj (16)  
TUNING MODE qk (16, 17)  
VOLUME +/– q; (22)  
+/– (tuning) qf (16)  
1
2
3
4
5
6
7
w;  
ql  
qk  
qj  
qh  
qg  
qf  
8
9
qd  
qs  
0
qa  
37GB  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Printed on 100 % recycled  
paper using VOC (Volatile  
Organic Compound)-free  
vegetable oil based ink.  
Sony Corporation Printed in China  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sennheiser Microphone E608 User Manual
Sharp All in One Printer AL 841 User Manual
Sharp Flat Panel Television LC 22SB27U User Manual
Shindaiwa Trimmer 81643 User Manual
Solid State Logic Music Mixer C300 HD User Manual
Sony MP3 Player DPF D70 User Manual
Sony TV Video Accessories TDGSV5P User Manual
Spectra Radio KT2078 User Manual
Star Manufacturing Oven HSCO14 User Manual
Swann DVR DVR4 NET User Manual