2-898-637-11(2)
Multi Channel AV
Receiver
Operating Instructions
Owner’s Record
The model and serial numbers are located on the rear of the unit. Record the
serial number in the space provided below. Refer to them whenever you call
upon your Sony dealer regarding this product.
Model No.
Serial No.
STR-DG710
©2007 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Manual
• The instructions in this manual are for model
STR-DG710. Check your model number by
looking at the lower right corner of the front panel.
In this manual, models of area code U is used for
illustration purposes unless stated otherwise. Any
difference in operation is clearly indicated in the
text, for example, “Models of area code CA only”.
• The instructions in this manual describe the
controls on the supplied remote. You can also use
the controls on the receiver if they have the same
or similar names as those on the remote.
About area codes
The area code of the receiver you purchased is
shown on the lower right portion of the rear panel
(see the illustration below).
SURROUND BACK
L
R
NT
A
SURROUND
CENTER
RS
Area code
Any differences in operation, according to the area
code, are clearly indicated in the text, for example,
“Models of area code AA only”.
This receiver incorporates Dolby* Digital and Pro
Logic Surround and the DTS** Digital Surround
System.
*
Manufactured under license from Dolby
Laboratories.
“Dolby”, “Pro Logic”, “Surround EX”, and the
double-D symbol are trademarks of Dolby
Laboratories.
** “DTS”, “DTS-ES Neo:6” are registered
trademarks of DTS, Inc. “96/24” is a trademark
of DTS, Inc.
This receiver incorporates High-Definition
Multimedia Interface (HDMITM) technology.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.
XM is a registered trademark of XM Satellite Radio
Inc.
3US
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Listening to the sound without any
adjustment (ANALOG DIRECT).......... 54
Resetting sound fields to the initial
7: Calibrating the appropriate settings
settings ................................................... 55
(AUTO CALIBRATION).......................28
8: Adjusting the speaker levels and balance
Switching between digital and analog
audio (INPUT MODE) .......................... 67
Enjoying the DIGITAL MEDIA PORT
(DMPORT) ............................................ 68
Listening to digital sound from other
inputs (DIGITAL ASSIGN)................... 71
Settings for the surround sound
Calibrating the appropriate settings
Enjoying Dolby Digital and DTS Surround
sound (AUTO FORMAT DIRECT) .......49
Using only the front speakers
(2CH STEREO)......................................54
4US
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Description and location of parts
Front panel
1
2
3
4
5
6
7
8
?/1
MASTER VOLUME
TUNING MODE
TUNING
DISPLAY
INPUT MODE
INPUT SELECTOR
SPEAKERS
(OFF/A/B)
AUTO CAL MIC
PHONES
MEMORY/ CATEGORY
ENTER MODE
CATEGORY
2CH
A.F.D.
MOVIE
MUSIC
AUTO CAL
DIRECT
VIDEO
VIDEO
3
IN/PORTABLE AV IN
L
AUDIO
R
qhqg
qf
Function
qd
qs
Name
qa
q;
9
Name
Function
A ?/1
Press to turn the receiver on
G INPUT MODE Press to select the input mode
when the same components
82).
are connected to both digital
B SPEAKERS
Press to select the front
(OFF/A/B)
speaker system (page 27).
H MASTER
Turn to adjust the volume
level of all speakers at the
35).
VOLUME
C TUNING
Press or turn to operate the
tuner (FM/AM/XM) (page
55).
MODE
TUNING +/–
I DIRECT
Press to listen to high quality
analog sound (page 54).
MEMORY/
ENTER
J AUTO CAL
Press to activate the Auto
Calibration function (page
29).
D Display
The current status of the
selected component or a list
of selectable items appears
K INPUT
Turn to select the input
74).
SELECTOR
E Remote
Receives signals from remote
commander.
sensor
F DISPLAY
Press to select information
displayed on the display
continued
5US
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
Function
L 2CH
Press to select a sound field
A.F.D.
MOVIE
MUSIC
M CATEGORY
Used when listening to XM
MODE
CATEGORY
+/–
N VIDEO 3 IN/
Connects to a portable audio/
PORTABLEAV video component such as a
IN jacks
camcorder or video game
O AUTO CAL
Connects to the supplied
optimizer microphone for the
Auto Calibration function
MIC jack
P PHONES jack Connects to headphones
6US
Download from Www.Somanuals.com. All Manuals Search And Download.
About the indicators on the display
1
2
3
4
5
6
7
8
9
q;
SP A
SP B
;
D EX
;
PL IIx
;
PL
OPT
DTS -ES 96/24 CAT
NEO:6
MEMORY
D.RANGE
ST
MONO
LFE
SW
L
HDMI COAX
C
R
SL
S
SR
SB
qh
qg
qf
Name
qd
qs
qa
Name
Function
Function
A SW
Lights up when sub woofer
E ; PL/
; PLII/
“; PL” lights up when the
receiver applies Pro Logic
processing to 2 channel signals
in order to output the center and
surround channel signals.
“; PLII” lights up when the
Pro Logic II Movie/Music/
Game decoder is activated.
“; PLIIx” lights up when the
Pro Logic IIx Movie/Music/
Game decoder is activated.
However, these indicators do
not light up if both the center
and surround speakers are set to
a sound field using the A.F.D.
button.
selection is set to “YES” (page
45) and the audio signal is
output from the SUB
; PLIIx
WOOFER jack.
B LFE
Lights up when the disc being
played back contains an LFE
(Low Frequency Effect)
channel and the LFE channel
signal is actually being
reproduced.
C SP A/SP B Lights up according to the
speaker system used. However,
these indicators do not light up
if the speaker output is turned
off or if headphones are
Note
connected.
Dolby Pro Logic IIx decoding
does not function for DTS
format signals or for signals
with a sampling frequency of
more than 48 kHz.
D ; D/
; D EX
“; D” lights up when the
receiver is decoding Dolby
Digital signals. “; D EX”
lights up when the receiver is
decoding Dolby Digital
Surround EX signals.
F OPT
Lights up when INPUT MODE
is set to “AUTO IN” and the
source signal is a digital signal
being input through the
OPTICAL jack, or when
INPUT MODE is set to “OPT
Note
When playing a Dolby Digital
format disc, be sure that you
have made digital connections
and that INPUT MODE is not
set to “ANALOG” (page 67).
continued
7US
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
Function
Name
Function
G DTS/
“DTS” lights up when the
receiver is decoding DTS
signals. “DTS-ES” lights up
when the receiver is decoding
DTS-ES signals. “DTS 96/24”
lights up when the receiver is
decoding DTS 96/24 (96 kHz/
24 bit) signals.
P Playback
channel
The letters (L, C, R, etc.)
indicate the channels being
played back. The boxes around
the letters vary to show how the
receiver downmixes the source
sound (based on the speaker
settings).
DTS-ES/
DTS 96/24
indicators
L
Front Left
Note
R
C
SL
SR
S
Front Right
Center (monaural)
Surround Left
Surround Right
Surround (monaural or the
surround components obtained
by Pro Logic processing)
Surround back (the surround
back components obtained by
6.1 channel decoding)
Example:
When playing a DTS format
disc, be sure that you have
made digital connections and
that INPUT MODE is not set to
“ANALOG” (page 67).
H CAT
Lights up when “ALL CAT”
mode is changed to “ONE
CAT” mode during XM Radio
SB
Recording format (Front/
Surround): 3/2.1
Output channel: When
surround speakers are set to
“NO” (page 39)
I MEMORY
Lights up when a memory
function, such as Preset
activated.
J Tuner
Lights up when using the
receiver to tune in radio
Sound Field: A.F.D. AUTO
indicators
SW
K Preset
station
Lights up when using the
receiver to tune in radio
stations you have preset. For
details on presetting radio
stations, see page 57.
L
C
R
indicators
SL
SR
L D.RANGE
M NEO:6
N COAX
Lights up when dynamic range
compression is activated (page
37).
Lights up when DTS Neo:6
Cinema/Music decoder is
Lights up when INPUT MODE
is set to “AUTO IN” and the
source signal is a digital signal
being input through the
COAXIAL jack, or when
INPUT MODE is set to
“COAX IN” (page 67)
O HDMI
Lights up when the receiver
recognizes a component
connected via a HDMI IN jack
8US
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear panel
1
2
DIGITAL
DVD IN
VIDEO 2/BD IN
OUT
(ASSIGNABLE)
OPTICAL
ANTENNA
SAT
IN
HDMI
Y
AM
VIDEO
IN
1
XM
PB/CB
COAXIAL
DVD
IN
PR/CR
SURROUND BACK
L
L
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN VIDEO OUT
SAT IN
DVD IN
VIDEO
1
IN MONITOR OUT
DMPORT
DVD
MONITOR
COMPONENT VIDEO
R
L
L
L
L
AUDIO OUT
R
R
R
R
R
IN
IN
AUDIO IN
AUDIO OUT AUDIO IN
FRONT
B
FRONT
A
SURROUND
CENTER
SUB
SA-CD
/
CD
TV
SAT
VIDEO 1
WOOFER
SPEAKERS
6 5
4
3
A DIGITAL INPUT/OUTPUT section
C SPEAKERS section
OPTICAL
IN jacks
Connects to a
Connects to
DVD player, etc.
The COAXIAL
jack provides a
better quality of
loud sound (page
COAXIAL IN
jack
HDMI IN/
OUT jacks*
Connects to a
DVD player, etc.
The image and the
sound are output to
a TV or a projector
Connects to a sub
woofer (page 15).
D VIDEO/AUDIO INPUT/OUTPUT
section
DMPORT
jack
Connects to a
DIGITALMEDIA
PORT adapter
AUDIO IN/
OUT jacks
Connects to a VCR,
a DVD player, etc.
White (L)
Red (R)
B COMPONENT VIDEO INPUT/
VIDEO IN/
OUT jacks*
Yellow
OUTPUT section
COMPONENT Connects to a
Green (Y)
VIDEO
INPUT/
OUTPUT
jacks*
DVD player, TV,
or a satellite tuner.
You can enjoy
high quality image
E AUDIO INPUT section
Blue
(PB/CB)
AUDIO IN
jacks
Connects to a CD
player, etc. (page
16).
White (L)
Red
(PR/CR)
Red (R)
continued
9US
Download from Www.Somanuals.com. All Manuals Search And Download.
F ANTENNA section
Remote commander
You can use the supplied remote
RM-AAU014 to operate the receiver and to
control the Sony audio/video components that
the remote is assigned to operate (page 74).
FM
ANTENNA
jack
Connects to the FM
wire antenna
(aerial) supplied
with this receiver
AM
ANTENNA
terminals
Connects to the AM
loop antenna
(aerial) supplied
with this receiver
1
TV INPUT
TV ?/1
?/1
SLEEP DMPORT AV ?/1
wa
2
SYSTEM STANDBY
VIDEO 1 VIDEO 2 VIDEO 3
DVD
XM
ANTENNA
jack
Connects to the XM
Connect-and-Play
antenna (not
3
4
SAT
2CH
TV
SA-CD/CD TUNER
A.F.D.
MOVIE
MUSIC
AMP MENU
AUTO CAL
* You can watch the selected input image when you
connect the MONITOR OUT or HDMI OUT jack
1
4
7
2
5
3
6
9
5
6
7
w;
D.TUNING
D.SKIP
MEMORY DVD MENU
ENTER
8
>10/
-
0/10
8
9
ql
qk
qj
CLEAR
FM MODE
MUTING
DISPLAY
TOOLS
q;
F
f
TV VOL
MASTER VOL
G
g
qh
qa
qg
qf
RETURN/EXIT
TV CH –
MENU
– CATEGORY +
TV CH +
PRESET – REPLAY ADVANCE PRESET +
.
<
<
>
TUNING – CATEGORY MODE TUNING +
m
H
M
x
qs
TV
X
qd
10US
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
Function
Name
Function
A TV ?/1
Press TV ?/1 and TV (M) at
D 2CH
Press to select a sound field.
(on/standby) the same time to turn the TV
A.F.D.
on or off.
MOVIE
MUSIC
AV ?/1
Press to turn on or off the
(on/standby) Sonyaudio/videocomponents
that the remote is assigned to
operate (page 74).
E AMP MENU
Press to display the menu of
the receiver. Then, use V, v,
If you press ?/1 (B) at the
same time, it will turn off the
receiver and other
B, b and
(P) to perform
menu operations.
components (SYSTEM
STANDBY).
Note
The function of the AV ?/1
switch changes automatically
each time you press the input
buttons (C).
F AUTO CAL
G D.TUNING
D.SKIP
Press to activate the Auto
Calibration function.
Press to enter direct tuning
mode.
Press to skip a disc when
using a multi-disc changer.
B ?/1
Press to turn the receiver on or
H DVD MENU
Press to display the menu of
the DVD player on the TV
screen. Then, use V, v, B, b
(on/standby) off.
To turn off all components,
press ?/1 and AV ?/1 (A) at
the same time (SYSTEM
STANDBY).
and
(P) to perform menu
operations.
FM MODE
Press to select the FM
monaural or stereo reception.
C Input buttons Press one of the buttons to
select the component you
I ENTER
Press to enter the value after
selecting a channel, disc or
track using the numeric
buttons of the TV, VCR or
satellite tuner.
want to use. When you press
any of the input buttons, the
receiver turns on. The buttons
are factory assigned to control
Sony components as follows.
You can change the button
assignments following the
MEMORY
Press to store a station.
steps in “Changing button
J MUTING
Press to activate the muting
function.
Press MUTING and TV (M)
at the same time to activate
the TV’s muting function.
Button
Assigned Sony
component
DMPORT DIGITAL MEDIA
PORT adapter
K TV VOL
Press TV VOL +/– and TV
(M) at the same time to adjust
the TV volume level.
a)
+ /–
VIDEO 1 VCR (VTR mode 3)
VIDEO 2 VCR (VTR mode 2)
VIDEO 3 Not assigned
MASTER
Press to adjust the volume
level of all speakers at the
same time.
a)
VOL + /–
DVD
SAT
DVD player
b)
L ./>
Press to skip a track of the CD
player, DVD player or blu-ray
disc player.
Digital Satellite
Receiver
TV
TV
<
REPLAY
ADVANCE
/
Press to replay the previous
SA-CD/CD Super Audio CD/
CD player
<
scene or fast forward the
current scene of the VCR,
DVD player or blu-ray disc
player.
TUNER
Built-in tuner
continued
11US
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
Function
Name
Function
b)
m/M
Press to
O RETURN/
Press to
EXIT O
– search tracks in the forward/
reverse direction of the DVD
player.
– start fast forward/rewind of
the VCR, CD player or blu-
ray disc player.
– return to the previous menu.
– exit the menu while the
menu or on-screen guide of
the VCR, DVD player,
satellite tuner or blu-ray disc
player is displayed on the
TV screen.
PressRETURN/EXITandTV
(M) at the same time to return
to the previous menu or exit
the TV’s menu while the
menu is displayed on the TV
screen.
a)b)
H
Press to start playback of the
VCR, CD player, DVD player,
or blu-ray disc player.
b)
X
Press to pause playback or
recording of the VCR, CD
player, DVD player or blu-ray
disc player. (Also starts
recording with components in
recording standby.)
P
After pressing AMP MENU
(E), DVD MENU (H), or
MENU (N), press V, v, B or
b to select the settings. Then,
press
for DVD MENU or MENU.
Press also to enter the
selection of the receiver,
VCR, satellite tuner, CD
player, DVD player or blu-ray
disc player.
V/v/B/b
b)
x
Press to stop playback of the
VCR, CD player, DVD player
or blu-ray disc player.
to enter the selection
TV CH +/–
Press TV CH +/– and TV (M)
at the same time to select
preset TV channels.
CATEGORY Press to select the category for
Q DISPLAY
Press to select information
displayed on the TV screen of
the VCR, satellite tuner, CD
player, DVD player or blu-ray
disc player.
Press DISPLAY and TV (M)
at the same time to display
TV’s information on the TV
screen.
PRESET +/– Press to select
– preset stations.
– preset channels of the VCR
or satellite tuner.
TUNING +/– Press to scan a station.
CATEGORY Press to select the category
MODE
mode for XM Radio (page 63).
R TOOLS
Press to display options
M TV
Press TV and the button you
want at the same time to
activate the buttons with
orange printing.
applicable to the entire disc
(e.g. disc protection), recorder
(e.g. audio settings during
recording), or multiple items
on a list menu (e.g. erasing
multiple titles).
Press TOOLS and TV (M) at
the same time to display
options applicable to the TV.
N MENU
Press to display the menu of
the VCR, DVD player,
satellite tuner or blu-ray disc
player on the TV screen.
Press MENU and TV (M) at
the same time to display the
TV’s menu.
Then, use V, v, B, b and
(P) to perform menu
operations.
12US
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
Function
S -/--
Press -/-- and TV (M) at the
same time to select the
channel entry mode, either
one or two digits of the TV.
x
>10/
Press to select
– track numbers over 10 of the
VCR, satellite tuner or CD
player.
– channel numbers of the
Digital CATV terminal.
CLEAR
Press to clear a mistake when
you press the incorrect
numeric button.
T Numeric
Press to
– preset/tune to preset
stations.
buttons
a)
(number 5 )
– select track numbers of the
CD player, DVD player or
blu-ray disc player. Press 0/
10 to select track number 10.
– select channel numbers of
the VCR or satellite tuner.
Press the numeric buttons and
TV (M) at the same time to
select the TV channels.
U TV INPUT
Press TV INPUT and TV (M)
at the same time to select the
input signal (TV input or
video input).
SLEEP
Press to activate the Sleep
Timer function and the
duration which the receiver
turns off automatically.
a)
The number 5, MASTER VOL +, TV VOL +, and
H buttons have tactile dots. Use the tactile dots
as references when operating the receiver.
This button is also available for DIGITAL MEDIA
PORT adapter operation. For details on the
function of the button, refer to the operating
instructions supplied with the DIGITAL MEDIA
PORT adapter.
b)
Notes
• Some functions explained in this section may not
work depending on the model.
• The above explanation is intended to serve as an
example only. Therefore, depending on the
component, the above operation may not be
possible or may operate differently than described.
13US
Download from Www.Somanuals.com. All Manuals Search And Download.
1: Installing speakers
This receiver allows you to use a 6.1 channel
system (6 speakers and one sub woofer).
You can enjoy high fidelity reproduction of
DVD software recorded sound in the Surround
EX format if you connect one additional
surround back speaker (6.1 channel) (see
Enjoying a 5.1/6.1 channel
system
To fully enjoy theater-like multi channel
surround sound requires five speakers (two
front speakers, a center speaker, and two
surround speakers) and a sub woofer (5.1
channel).
Example of a 6.1 channel
speaker system configuration
Example of a 5.1 channel
speaker system configuration
AFront speaker (left)
BFront speaker (right)
CCenter speaker
DSurround speaker (left)
ESurround speaker (right)
FSurround back speaker
GSub woofer
AFront speaker (left)
BFront speaker (right)
CCenter speaker
DSurround speaker (left)
ESurround speaker (right)
GSub woofer
Tip
Since the sub woofer does not emit highly
directional signals, you can place it wherever you
want.
14US
Download from Www.Somanuals.com. All Manuals Search And Download.
2: Connecting speakers
G
A
D
F
A
B
DVD IN
VIDEO 2/BD IN
OUT
HDMI
Y
XM
PB/CB
PR/CR
SURROUND BACK
L
L
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN VIDUT
SAT IN
DVD IN
VIDEO
1
IN MONITOR OUT
MONOR
COMPONENT VIDEO
DVD
R
L
L
L
L
AUDIO OUT
R
R
R
R
R
IN
AUDIO IN
AUDIO OUT AUDIO IN
FRONT B
FRONT A
SURROUND
CENTER
SUB
TV
SAT
VIDEO 1
WOOFER
SPEAKERS
SPEAKERS FRONT B terminalsa)
B
B
E
C
AMonaural audio cord (not supplied)
BSpeaker cords (not supplied)
a)
If you have an additional front speaker system,
connect them to the SPEAKERS FRONT B
terminals. You can select the front speakers you
want to use with SPEAKERS (OFF/A/B) on the
When you connect a sub woofer with an auto
standby function, turn off the function when
watching movies. If the auto standby function is
set to on, it turns to standby mode automatically
based on the level of the input signal to a sub
woofer, then sound may not be output.
AFront speaker A (left)
BFront speaker A (right)
CCenter speaker
DSurround speaker (left)
ESurround speaker (right)
FSurround back speaker
b)
b)
GSub woofer
15US
Download from Www.Somanuals.com. All Manuals Search And Download.
3a: Connecting the audio components
Connecting a Super Audio CD/
CD player
The following illustration shows how to
connect a Super Audio CD/CD player.
After connecting your Super Audio CD/CD
player, proceed to “3b: Connecting the video
Super Audio CD
player/CD player
A
DIGITAL
DVD IN
VIDEO 2/BD IN
OUT
(ASSIGNABLE)
OPTICAL
ANTENNA
SAT
IN
HDMI
Y
AM
VIDEO
IN
1
XM
PB/CB
COAXIAL
DVD
IN
PR/CR
SURROUND BACK
L
L
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN VIDEO OUT
SAT IN
DVD IN
VIDEO
1
IN MONITOR OUT
DMPORT
DVD
MONITOR
COMPONENT VIDEO
R
L
L
L
L
AUDIO OUT
R
R
R
R
R
IN
IN
AUDIO IN
AUDIO OUT AUDIO IN
FRONT B
FRONT A
SURROUND
CENTER
SUB
SA-CD
/
CD
TV
SAT
VIDEO 1
WOOFER
SPEAKERS
AAudio cord (not supplied)
16US
Download from Www.Somanuals.com. All Manuals Search And Download.
3b: Connecting the video components
How to connect your
components
Video input/output jacks to be
connected
This section describes how to connect your
video components to this receiver. Before you
begin, refer to “Component to be connected”
below for the pages which describe how to
connect each component.
After connecting all your components,
proceed to “4: Connecting the antennas
The image quality depends on the connecting
jack. Refer to the illustration that follows.
Select the connection according to the jacks on
your components.
TV, etc. INPUT
jack
COMPONENT
HDMI
HDMI
VIDEO
VIDEO
VIDEO
Component to be connected
Component
Page
Receiver
MONITOR OUT,
HDMI OUT jack
COMPONENT
VIDEO
With HDMI jack
TV
DVD player/DVD recorder
Satellite tuner/Set-top box
VCR
?/1
MASTER VOLUME
TUNING MODE
TUNING
DISPLA
Y
I
N
P
U
T
M
O
D
E
INPUT SELECTOR
SPEAKERS
(OFF/A/B)
A
UTO
C
A
L
M
I
C
M
E
M
O
R
Y
/
C
A
T
E
G
O
R
Y
E
N
T
E
R
M
O
D
E
CATEGORY
2CH
A.F.D.
MOVIE
MUSIC
AUTO
CAL
DIRECT
VIDEO
VIDEO
3
IN/PORTABLE
A
V
IN
PHONES
L
A
UDIO
R
COMPONENT
VIDEO
HDMI
HDMI
VIDEO
Camcorder, video game, etc.
Receiver INPUT
jack
If you want to connect several
digital components, but cannot
find an unused input
Video component
OUTPUT jack
COMPONENT
VIDEO
VIDEO
High quality image
17US
Download from Www.Somanuals.com. All Manuals Search And Download.
HDMI feature
Connecting components with
HDMI jacks
A digital audio signal transmitted by HDMI
can be output from the speakers on this
receiver. This signal supports Dolby Digital,
DTS, and linear PCM.
HDMI is the abbreviated name for High-
Definition Multimedia Interface. It is an
interface which transmits video and audio
signals in digital format.
DVD player
Blu-ray disc player
TV, projector, etc.
Audio/video
signals
Audio/video
signals
Audio/video
signals
A
A
A
DIGITAL
DVD IN
VIDEO 2/BD IN
OUT
(ASSIGNABLE)
OPTICAL
ANTENNA
SAT
IN
HDMI
Y
AM
VIDEO
IN
1
XM
PB/CB
COAXIAL
DVD
IN
PR/CR
SURROUND BACK
L
L
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN VIDEO OUT
SAT IN
DVD IN
VIDEO
1
IN MONITOR OUT
DMPORT
DVD
MONITOR
COMPONENT VIDEO
R
L
L
L
L
AUDIO OUT
R
R
R
R
R
IN
IN
AUDIO IN
AUDIO OUT AUDIO IN
FRONT B
FRONT A
SURROUND
CENTER
SUB
SA-CD
/
CD
TV
SAT
VIDEO 1
WOOFER
SPEAKERS
AHDMI cable (not supplied)
We recommend that you use a Sony HDMI cable.
18US
Download from Www.Somanuals.com. All Manuals Search And Download.
• We do not recommend using a HDMI-DVI
conversion cable. When you connect a
HDMI-DVI conversion cable to a DVI-D
component, the sound and/or the image may
not be output.
Notes on HDMI connections
• Check the setup of the connected component
if an image is poor or the sound does not
come out of a component connected via the
HDMI cable.
• An audio signal input to the HDMI IN jack
is output from the speaker output jack and
HDMI OUT jack. It is not output from any
other audio jacks.
• Video signals input to the HDMI IN jack can
only be output from the HDMI OUT jack.
The video input signals cannot be output
from the VIDEO OUT jacks or MONITOR
OUT jacks.
• When you want to listen to the sound from
the TV speaker, set “AUDIO” to
“TV+AMP” in the VIDEO menu (page 44).
If set to “AMP”, the sound is not output from
the TV speaker.
Notes
• Be sure to turn on the receiver when the video and
audio signals of a playback component are being
output to a TV via the receiver. Unless the power is
turned on, neither video nor audio signals will be
transmitted.
• Be sure to change the factory setting of the VIDEO
2 input button on the remote so that you can use the
button to control your blu-ray disc player. For
74).
• You can also rename the VIDEO 2 input so that it
can be displayed on the receiver’s display. For
• The multi/stereo area audio signals of a
Super Audio CD are not output.
• Audio signals (sampling frequency, bit
length, etc.) transmitted from a HDMI jack
may be suppressed by the connected
component. Check the setup of the
connected component if an image is poor or
the sound does not come out of a component
connected via the HDMI cable.
• Sound may be interrupted when the
sampling frequency or the number of
channels of audio output signals from the
playback component is switched.
• When the connected component is not
compatible with copyright protection
technology (HDCP), the image and/or the
sound from the HDMI OUT jack may be
distorted or may not be output.
In this case, check the specification of the
connected component.
• Set the resolution of the image of the
playback component to 720p or 1080i when
you output 96 kHz multi-channel sound over
a HDMI connection.
• Refer to the operating instructions of each
component connected for details.
19US
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Connecting a TV
Be sure to turn on the receiver when the video and
audio signals of a playback component are being
output to a TV via the receiver. Unless the power is
turned on, neither video nor audio signals will be
transmitted.
The image from a video component connected
to this receiver can be displayed on a TV
screen.
It is not necessary to connect all the cords.
Connect audio and video cords according to
the jacks of your components.
Tips
• You can watch the selected input image when you
connect the MONITOR OUT jack to a TV or
projector.
• The sound of the TV is output from the speakers
connected to the receiver if you connect the audio
output jack of the TV and the TV IN jacks of the
receiver.
TV
Audio signals
Video signals
A
B
C
DIGITAL
DVD IN
VIDEO 2/BD IN
OUT
(ASSIGNABLE)
OPTICAL
ANTENNA
SAT
IN
HDMI
Y
AM
VIDEO
IN
1
XM
PB/CB
COAXIAL
DVD
IN
PR/CR
SURROUND BACK
L
L
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN VIDEO OUT
SAT IN
DVD IN
VIDEO
1
IN MONITOR OUT
DMPORT
DVD
MONITOR
COMPONENT VIDEO
R
L
L
L
L
AUDIO OUT
R
R
R
R
R
IN
IN
AUDIO IN
AUDIO OUT AUDIO IN
FRONT B
FRONT A
SURROUND
CENTER
SUB
SA-CD
/
CD
TV
SAT
VIDEO 1
WOOFER
SPEAKERS
AAudio cord (not supplied)
BVideo cord (not supplied)
CComponent video cord (not supplied)
20US
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Connecting a DVD player/DVD
recorder
To input multi channel digital audio from the DVD
player, set the digital audio output setting on the
DVD player. Refer to the operating instructions
supplied with the DVD player.
The following illustration shows how to
connect a DVD player/DVD recorder.
It is not necessary to connect all the cords.
Connect audio and video cords according to
the jacks of your components.
Tip
All the digital audio jacks are compatible with
32 kHz, 44.1 kHz, 48 kHz, and 96 kHz sampling
frequencies.
Connecting a DVD player
DVD player
Audio signals
Video signals
A
B
C
DIGITAL
DVD IN
VIDEO 2/BD IN
O
(ASSIGNABLE)
OPTICAL
ANTENNA
SAT
IN
HDMI
Y
AM
VIDEO
IN
1
XM
PB/CB
COAXIAL
DVD
IN
PR/CR
SURROUND BACK
L
L
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN VIDEO OUT
SAT IN
DVD IN
VIDEO
1
IN MONITOR OUT
DMPORT
DVD
MONITOR
COMPONENT VIDEO
R
L
L
L
L
AUDIO OUT
R
R
R
R
R
IN
IN
AUDIO IN
AUDIO OUT AUDIO IN
FRONT B
FRONT A
SURROUND
CENTER
SUB
SA-CD
/
CD
TV
SAT
VIDEO 1
WOOFER
SPEAKERS
ACoaxial digital cord (not supplied)
BVideo cord (not supplied)
CComponent video cord (not supplied)
continued
21US
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a DVD recorder
DVD recorder
Audio signals
Video signals
A
B
C
D
DIGITAL
DVD IN
VIDEO 2/BD IN
OUT
(ASSIGNABLE)
OPTICAL
ANTENNA
SAT
IN
HD
Y
AM
VIDEO
IN
1
XM
PB/CB
COAXIAL
DVD
IN
PR/CR
SURROUND BACK
L
L
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN VIDEO OUT
SAT IN
DVD IN
VIDEO
1
IN MONITOR OUT
DMPORT
DVD
MONITOR
COMPONENT VIDEO
R
L
L
L
L
AUDIO OUT
R
R
R
R
R
IN
N
AUDIO IN
AUDIO OUT AUDIO IN
FRONT B
FRONT A
SURROUND
CENTER
SUB
SA-CD
/
CD
V
SAT
VIDEO 1
WOOFER
SPEAKERS
AOptical digital cord (not supplied)
BAudio cord (not supplied)
CVideo cord (not supplied)
DComponent video cord (not supplied)
Notes
Tip
• Be sure to change the factory setting of the VIDEO
1 input button on the remote so that you can use the
button to control your DVD recorder. For details,
• You can also rename the VIDEO 1 input so that it
can be displayed on the receiver’s display. For
• When connecting optical digital cords, insert the
plugs straight in until they click into place.
• Do not bend or tie optical digital cords.
All the digital audio jacks are compatible with
32 kHz, 44.1 kHz, 48 kHz, and 96 kHz sampling
frequencies.
22US
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Connecting a satellite tuner/
set-top box
• When connecting optical digital cords, insert the
plugs straight in until they click into place.
• Do not bend or tie optical digital cords.
The following illustration shows how to
connect a satellite tuner or a set-top box.
It is not necessary to connect all the cords.
Connect audio and video cords according to
the jacks of your components.
Tip
All the digital audio jacks are compatible with
32 kHz, 44.1 kHz, 48 kHz, and 96 kHz sampling
frequencies.
Satellite tuner/set-top box
Audio signals
Video signals
A
B
C
D
DIGITAL
DVD IN
VIDEO 2/BD IN
OUT
(ASSIGNABLE)
OPTICAL
ANTENNA
SAT
IN
HDMI
Y
AM
VIDEO
IN
1
XM
PB/CB
COAXIAL
DVD
IN
PR/CR
SURROUND BACK
L
L
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN VIDEO OUT
SAT IN
DVD IN
VIDEO
1
IN MONITOR OUT
DMPORT
DVD
MONITOR
COMPONENT VIDEO
R
L
L
L
L
AUDIO OUT
R
R
R
R
R
IN
IN
AUDIO IN
AUDIO OUT AUDIO IN
FRONT B
FRONT A
SURROUND
CENTER
SUB
SA-CD
/
CD
TV
SAT
VIDEO 1
WOOFER
SPEAKERS
AOptical digital cord (not supplied)
BAudio cord (not supplied)
CVideo cord (not supplied)
DComponent video cord (not supplied)
23US
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting components with
analog video and audio jack
The following illustration shows how to
connect a component which has analog jacks
such as a VCR, etc.
It is not necessary to connect all the cords.
Connect audio and video cords according to
the jacks of your components.
VCR
Audio signals
Video signals
A
B
DIGITAL
DVD IN
VIDEO 2/BD IN
OUT
(ASSIGNABLE)
OPTICAL
ANTENNA
SAT
IN
HD
Y
M
VIDEO
IN
1
XM
PB/CB
COAXIAL
DVD
IN
PR/CR
SURROUND BACK
L
L
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN VIDEO OUT
SAT IN
DVD IN
VIDEO
1
IN MONITOR OUT
DMPORT
DVD
MONITOR
COMPONENT VIDEO
R
L
L
L
L
AUDIO OUT
R
R
R
R
R
IN
IN
AUDIO IN
AUDIO OUT AUDIO IN
FRONT B
FRONT A
SURROUND
CENTER
SUB
SA-CD
/
CD
TV
SAT
VIDEO 1
WOOFER
SPEAKERS
VIDEO 3 IN/PORTABLE AV IN
VIDEO
L
AUDIO
R
To the VIDEO 3 IN/PORTABLE AV IN jacks
(Front panel)
Camcorder/
video game
C
AAudio cord (not supplied)
BVideo cord (not supplied)
CAudio/video cord (not supplied)
24US
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Connecting the antennas (aerials)
Connect the supplied AM loop antenna
(aerial) and FM wire antenna (aerial).
FM wire antenna (aerial) (supplied)
AM loop antenna (aerial)
(supplied)
DIGITAL
DVD IN
VIDEO 2/BD IN
OUT
(ASSIGNABLE)
OPTICAL
ANTENNA
SAT
IN
HDMI
Y
AM
VIDEO
IN
1
XM
PB/CB
COAXIAL
DVD
IN
PR/CR
SURROUND BACK
L
L
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN VIDEO OUT
SAT IN
DVD IN
VIDEO
1
IN MONITOR OUT
DMPORT
DVD
MONITOR
COMPONENT VIDEO
R
L
L
L
L
AUDIO OUT
R
R
R
R
R
IN
IN
AUDIO IN
AUDIO OUT AUDIO IN
FRONT B
FRONT A
SURROUND
CENTER
SUB
SA-CD
/
CD
TV
SAT
VIDEO 1
WOOFER
SPEAKERS
* The shape of the connector varies depending on
the area code of this receiver.
Notes
• To prevent noise pickup, keep the AM loop
antenna (aerial) away from the receiver and other
components.
• Be sure to fully extend the FM wire antenna
(aerial).
• After connecting the FM wire antenna (aerial),
keep it as horizontal as possible.
25US
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing initial setup
operations
5: Preparing the receiver
and the remote
Before using the receiver for the first time,
initialize the receiver by performing the
following procedure. This procedure can also
be used to return settings you have made to
their factory defaults.
Connecting the AC power cord
(mains lead)
Be sure to use the buttons on the receiver for
this operation.
Connect the AC power cord (mains lead) to a
wall outlet.
1,2
AC power cord (mains lead)
?/
MASTER VOLUME
TUNING MODE
TUNING
DISPLA
Y
INPUT MODE
INPUT SELECTOR
SPEAKERS
(OFF/A/B)
AUTO CAL MIC
PHONES
MEMORY/ CATEGORY
ENTER
MODE
CATEGORY
2CH
A.F.D.
MOVIE
MUSIC
AUTO CAL
DIRECT
VIDEO
VIDEO
3
IN/PORTABLE AV IN
L
AUDIO
R
SURROUND BACK
L
3
1 Press ?/1 to turn off the
receiver.
R
SURROUND
CENTER
2 Hold down ?/1 for 5 seconds.
“PUSH” and “ENTER” appears on the
display alternately.
3 Press MEMORY/ENTER.
To the wall outlet
After “CLEARING” appears on the
display for a while, “CLEARED”
appears.
The following items are reset to their
factory settings.
• All settings in the LEVEL, EQ, SUR,
TUNER, AUDIO, VIDEO and
SYSTEM menus.
• The sound field memorized for each
input and preset station.
• All sound field parameters.
• All preset stations.
• All index names for inputs and preset
stations.
• MASTER VOLUME is set to “VOL
MIN”.
• Input is set to “DVD”.
26US
Download from Www.Somanuals.com. All Manuals Search And Download.
Inserting batteries into the
remote
6: Selecting the speaker
system
You can select the front speakers you want to
drive.
Insert two R6 (size-AA) batteries in the
RM-AAU014 remote commander.
Observe the correct polarity when installing
batteries.
Be sure to use the buttons on the receiver for
this operation.
SPEAKERS (OFF/A/B)
?/1
MASTER VOLUME
TUNING MODE
TUNING
DISPLA
Y
INPUT MODE
INPUT SELECTOR
SPEAKERS
(OFF/A/B)
AUTO CAL MIC
PHONES
MEMORY/ CATEGORY
ENTER MODE
CATEGORY
2CH
A.F.D.
MOVIE
MUSIC
AUTO CAL
DIRECT
VIDEO
VIDEO
3
IN/PORTABLE AV IN
L
AUDIO
R
Notes
Press SPEAKERS (OFF/A/B)
repeatedly to select the front
speaker system you want to drive.
• Do not leave the remote in an extremely hot or
humid place.
• Do not use a new battery with old ones.
• Do not mix alkaline batteries and other kinds of
batteries.
To select
Light up
• Do not expose the remote sensor to direct sunlight
or lighting apparatuses. Doing so may cause a
malfunction.
• If you do not intend to use the remote for an
extended period of time, remove the batteries to
avoid possible damage from battery leakage and
corrosion.
• When you replace the batteries, the remote buttons
may be reset to their factory settings. If this
happens, reassign the buttons again (page 74).
The speakers connected to the
SPEAKERS FRONT A terminals
SP A
The speakers connected to the
SPEAKERS FRONT B terminals
SP B
To turn off the speaker output, press
SPEAKERS (OFF/A/B) repeatedly until the
“SP A” and “SP B” indicators on the display
do not light up.
Note
Tip
You cannot switch the front speaker system by
pressing SPEAKERS (OFF/A/B) when the
headphones are connected to the receiver.
Under normal conditions, the batteries should last
for about 3 months. When the remote no longer
operates the receiver, replace all the batteries with
new ones.
27US
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
• The Auto Calibration function does not work when
headphones are connected.
• Make sure SPEAKERS (OFF/A/B) is not set to off.
7: Calibrating the
appropriate settings
automatically
?/1
MASTER VOLUME
TUNING MODE
TUNING
DISPLAY
INPUT MODE
INPUT SELECTOR
SPEAKERS
(OFF/A/B)
Optimizer microphone
A
UTO CAL MIC
M
E
M
O
R
Y
/
C
A
T
E
G
O
R
Y
E
N
T
E
R
M
O
D
E
CATEGORY
2CH
A.F.D.
MOVIE
MUSIC
AUTO CAL
DIRECT
VIDEO
VIDEO
3
IN/PORTABLE
AV
IN
PHON
L
AUDIO
R
(AUTO CALIBRATION)
The DCAC (Digital Cinema Auto Calibration)
function allows you to perform automatic
calibration such as:
• Checking the connection between each
speaker and the receiver.
• Adjusting the speaker level.
• Measuring the distance of each speaker from
your listening position.
You can also adjust the speaker levels and
balance manually. For details, see
Before you perform Auto
Calibration
1 Connect the supplied optimizer
microphone to the AUTO CAL
MIC jack.
Before you perform Auto Calibration, install
• The AUTO CAL MIC jack is used for the
supplied optimizer microphone only. Do not
connect other microphones to this jack.
Doing so may damage the receiver and the
microphone.
• During calibration, the sound that comes out
of the speakers is very loud. Pay attention to
the presence of children or to the effect on
your neighborhood.
2 Set up the optimizer
microphone.
Place the optimizer microphone at your
listening position.You can also use a stool
or tripod so that the optimizer
microphone remains at the same height as
your ears.
• Perform Auto Calibration in a quiet
environment to avoid the effect of noise and
to get a more accurate measurement.
• If there are any obstacles in the path between
the optimizer microphone and the speakers,
the calibration cannot be performed
correctly. Remove any obstacles from the
measurement area to avoid measurement
error.
28US
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Measurement starts.
Performing Auto Calibration
The measurement process will take a few
minutes to complete.
The table below shows the display when
measurement starts.
TV INPUT
TV ?/1
?/1
SLEEP DMPORT AV ?/1
?/1
switch
SYSTEM STANDBY
Measurement for Display
VIDEO 1 VIDEO 2 VIDEO 3
DVD
Input
buttons
Environment noise NOISE.CHK
level
SAT
2CH
TV
SA-CD/CD TUNER
Speaker connection MEASURE and SP
DET. appears
A.F.D.
MOVIE
MUSIC
alternately*
AMP MENU
AUTO CAL
1
4
7
2
5
3
6
9
1
2
Speaker level
MEASURE and GAIN
appears alternately*
D.TUNING
D.SKIP
MEMORY DVD MENU
ENTER
Speaker distance
MEASURE and
DISTANCE appears
alternately*
8
>10/
-
0/10
CLEAR
FM MODE
* The corresponding speaker indicator lights
up in the display during measurement.
MUTING
DISPLAY
TOOLS
MUTING
F
f
TV VOL
MASTER VOL
G
g
4 Measurement ends.
MASTER
VOL +/–
“COMPLETE” appears on the display
and the settings are registered.
RETURN/EXIT
MENU
5 Disconnect the optimizer
microphone from the AUTO
CAL MIC jack.
1 Press AMP MENU.
2 Press AUTO CAL.
Measurement starts in 5 seconds and the
display changes as follows:
Note
Auto Calibration cannot detect the sub woofer.
Therefore, all sub woofer settings will be
maintained.
A.CAL [5] t A.CAL [4] t A.CAL [3]
t A.CAL [2] t A.CAL [1]
While the time is counting down, stand
away from the measurement area to avoid
measurement error.
Tip
During the measurement process, Auto Calibration
is canceled when you do the following.
– Press ?/1, input buttons or MUTING.
– Change the volume level.
– Press AUTO CAL again.
29US
Download from Www.Somanuals.com. All Manuals Search And Download.
Error code Cause and remedy
ERROR 23 Surround back speaker is detected
Error and warning codes
but surround speakers are not
connected. Be sure to connect the
surround speakers.
When error codes appear
When an error is detected during Auto
Calibration, an error code will appear on the
display cyclically after each measurement
process as follows:
When warning codes appear
During Auto Calibration, the warning code
provides information on the measurement
result. The warning code will appear on the
display cyclically as follows:
Error code tblank display t (error code t
a)
blank display) t PUSH t blank display
t ENTER
a)
Warning code t blank display t (warning
code t blank display) t PUSH t blank
Appears when there are more than one error code.
b)
display t ENTER
To rectify the error
b)
Appears when there are more than one warning
1 Record down the error code.
code.
2 Press
.
3 Press ?/1 to turn off the receiver.
4 Rectify the error.
below.
5 Turn on the receiver and perform Auto
Calibration again (page 29).
You can choose to ignore the warning code as
the Auto Calibration function will
automatically adjust the settings. You can also
change the settings manually.
To change the settings
manually
Error codes and remedies
1 Record down the warning code.
Error code Cause and remedy
2 Press
.
3 Press ?/1 to turn off the receiver.
4 Follow the solution provided in the
5 Turn on the receiver and perform Auto
Calibration again (page 29).
ERROR 10
The environment is too noisy.
Make sure the environment is quiet
during Auto Calibration.
ERROR 11
The speakers are placed too near
the optimizer microphone. Place
your speakers further away from
the optimizer microphone.
ERROR 12
None of the speakers are detected.
Make sure that the optimizer
microphone is connected properly
and perform Auto Calibration
again.
ERROR 20
ERROR 21
Front speakers are not detected or
only one front speaker is detected.
Check the front speaker
connection.
Only one surround speaker is
detected. Check the surround
speaker connection.
30US
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning codes and solutions
8: Adjusting the speaker
levels and balance
(TEST TONE)
Warning
code
Explanation and solution
WARN. 40
WARN. 60
WARN. 62
WARN. 63
WARN. 64
WARN. 65
WARN. 70
WARN. 72
WARN. 73
WARN. 74
WARN. 75
The environment is noisy. Make
sure the environment is quiet
during Auto Calibration.
The front speaker balance is out of
range. Reposition your front
You can adjust the speaker levels and balance
while listening to the test tone from your
listening position.
c)
speakers.
The center speaker level is out of
range. Reposition your center
Tip
d)
speaker.
The receiver employs a test tone with a frequency
centered at 800 Hz.
The surround left speaker level is
out of range. Reposition your
e)
surround left speaker.
TV INPUT
TV ?/1
?/1
SLEEP DMPORT AV ?/1
The surround right speaker level is
out of range. Reposition your
SYSTEM STANDBY
f)
surround right speaker.
VIDEO 1 VIDEO 2 VIDEO 3
DVD
Input
buttons
The surround back speaker level is
out of range. Reposition your
SAT
2CH
TV
SA-CD/CD TUNER
g)
surround back speaker.
A.F.D.
MOVIE
MUSIC
The front speaker distance is out of
range. Reposition your front
AMP MENU
AUTO CAL
1
4
7
2
5
3
6
9
1
c)
speakers.
The center speaker distance is out
of range. Reposition your center
D.TUNING
D.SKIP
MEMORY DVD MENU
ENTER
8
d)
speaker.
>10/
-
0/10
The surround left speaker distance
is out of range. Reposition your
CLEAR
FM MODE
MUTING
DISPLAY
TOOLS
e)
surround left speaker.
F
f
TV VOL
MASTER VOL
The surround right speaker distance
is out of range. Reposition your
G
g
2-5
f)
MASTER
VOL +/–
surround right speaker.
The surround back speaker distance
is out of range. Reposition your
RETURN/EXIT
MENU
g)
surround back speaker.
1 Press AMP MENU.
c)
For details, refer “Front speaker distance”
“1-LEVEL” appears on the display.
d)
e)
f)
For details, refer “Center speaker distance”
For details, refer “Surround left speaker distance”
For details, refer “Surround right speaker
For details, refer “Surround back speaker
2 Press
or b to enter the
menu.
3 Press V/v repeatedly to select
“T. TONE”.
g)
4 Press
or b to enter the
parameter.
continued
31US
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Press V/v repeatedly to select
“T. TONE Y”.
The test tone is output from each speaker
in sequence as follows:
Front left t Center t Front right t
Surround right t Surround back t
Surround left t Sub woofer
6 Adjust the speaker levels and
balance using the LEVEL menu
so that the level of the test tone
sounds the same from each
speaker.
For details, see “Adjusting the level
Tips
• To adjust the level of all speakers at the same
time, press MASTER VOL +/–. You can also
use MASTER VOLUME on the receiver.
• The adjusted value is shown on the display
during adjustment.
“T. TONE N”.
You can also press any input buttons.
The test tone turns off.
When a test tone is not output
from the speakers
• The speaker cords may not be connected
securely.
• The speaker cords may have the short-circuit
problem.
Note
The test tone does not work when ANALOG
DIRECT is selected.
32US
Download from Www.Somanuals.com. All Manuals Search And Download.
Selected input Components that can
[Display]
be played back
Playback
SAT
[SAT]
Satellite tuner, etc.
connected to the SAT
jack
Selecting a component
TV
[TV]
TV, etc. connected to the
TV jack
TV INPUT
SLEEP DMPORT AV ?/1
TV ?/1
?/1
SA-CD/CD
[SA-CD/CD]
Super Audio CD/CD
player, etc., connected to
the SA-CD/CD jack
SYSTEM STANDBY
VIDEO 1 VIDEO 2 VIDEO 3
DVD
1
TUNER
[FM or AM band]
Built-in radio tuner
SAT
2CH
TV
SA-CD/CD TUNER
A.F.D.
MOVIE
MUSIC
TUNER
For details, see page 60.
[XM RADIO]
AMP MENU
AUTO CAL
1
4
7
2
5
3
6
9
* “VIDEO 2/BD” and “VIDEO 3/PORTABLE
AV” scroll across the display, then “VIDEO
2” and “VIDEO 3” appear respectively.
D.TUNING
D.SKIP
8
MEMORY DVD MENU
ENTER
>10/
-
2 Turn on the component and
0/10
CLEAR
FM MODE
start playback.
MUTING
DISPLAY
TOOLS
MUTING
F
f
TV VOL
MASTER VOL
3 Press MASTER VOL +/– to
adjust the volume.
G
g
You can also use MASTER VOLUME on
the receiver.
3
RETURN/EXIT
MENU
To activate the muting function
Press MUTING.
The muting function will be canceled when
you do the following.
• Press MUTING again.
• Increase the volume.
1 Press the input button to select
a component.
You can also use INPUT SELECTOR on
the receiver.
The selected input appears on the display.
Selected input Components that can
• Turn off the receiver.
[Display]
be played back
DMPORT
[DMPORT]
DIGITALMEDIAPORT
adapter connected to the
DMPORT jack
To avoid damaging your
speakers
Before you turn off the receiver, be sure to turn
down the volume level.
VIDEO 1
[VIDEO 1]
VCR, etc., connected to
the VIDEO 1 jack
VIDEO 2
Blu-ray disc player, etc.,
[VIDEO 2/BD]* connected to the VIDEO
2/BD jack
VIDEO 3
[VIDEO 3/
PORTABLE
AV]*
Camcorder, video game,
etc., connected to the
VIDEO 3 IN/
PORTABLE AV IN jack
DVD
DVD player, etc.,
[DVD]
connected to DVD jack
33US
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening/Watching a component
Listening to a Super Audio CD/CD
TV INPUT
TV ?/1
?/1
SLEEP DMPORT AV ?/1
SYSTEM STANDBY
VIDEO DVD
2
3
VIDEO
SAT
1
VIDEO
TV
2
3
SA-CD/CD TUNER
2CH
A.F.D.
MOVIE
MUSIC
AMP MENU
AUTO CAL
1
4
7
2
5
3
6
9
?/1
MASTER VOLUME
TUNING MODE
TUNING
DISPLAY
INPUT MODE
D.TUNING
D.SKIP
MEMORY DVD MENU
ENTER
8
INPUT SELECTOR
>10/
-
0/10
SPEAKERS
(OFF/A/B)
CLEAR
FM MODE
5
3
DISPLAY
TOOLS MUTING
F
f
TV VOL
MASTER VOL
AUTO CAL MIC
PHONES
MEMORY/ CATEGORY
ENTER MODE
G
g
CATEGORY
2CH
A.F.D.
MOVIE
MUSIC
AUTO CAL
DIRECT
VIDEO
VIDEO
3
IN/PORTABLE AV IN
5
RETURN/EXIT
MENU
TV CH
–
–
CATEGORY
+
TV CH
+
PRESET
.
–
REPLAY ADVANCE PRESET
+
L
AUDIO
R
<
<
>
TUNING
–
CATEGORY MODE TUNING
+
m
H
M
x
TV
X
Notes
1 Turn on the Super Audio CD player/CD
• The operation is described for a
Sony Super Audio CD player.
• Refer to the operating
instructions supplied with the
Super Audio CD player or CD
player.
player, then place the disc on the tray.
2 Turn on the receiver.
3 Press SA-CD/CD.
You can also use INPUT SELECTOR on the receiver to
select “SA-CD/CD”.
Tip
You can select the sound field to
suit the music. Refer to page 51
for details.
Recommended sound fields:
Classical: HALL
4 Play back the disc.
5 Adjust to a suitable volume.
6 After you have finished listening to the
Super Audio CD/CD, eject the disc and turn
off the receiver and Super Audio CD player/
CD player.
Jazz: JAZZ
Live concert: CONCERT
34US
Download from Www.Somanuals.com. All Manuals Search And Download.
Watching a DVD
TV INPUT
TV ?/1
?/1
SLEEP DMPORT AV ?/1
SYSTEM STANDBY
VIDEO DVD
2
3
VIDEO
SAT
1
VIDEO
TV
2
3
SA-CD/CD TUNER
2CH
A.F.D.
MOVIE
MUSIC
AMP MENU
AUTO CAL
1
4
7
2
5
3
6
9
?/1
MASTER VOLUME
TUNING MODE
TUNING
DISPLAY
INPUT MODE
D.TUNING
D.SKIP
MEMORY DVD MENU
ENTER
8
INPUT SELECTOR
>10/
-
0/10
SPEAKERS
(OFF/A/B)
CLEAR
FM MODE
7
3
DISPLAY
TOOLS MUTING
F
f
TV VOL
MASTER VOL
AUTO CAL MIC
PHONES
MEMORY/ CATEGORY
ENTER MODE
G
g
CATEGORY
2CH
A.F.D.
MOVIE
MUSIC
AUTO CAL
DIRECT
VIDEO
VIDEO
3
IN/PORTABLE AV IN
7
RETURN/EXIT
MENU
TV CH
–
–
CATEGORY
+
TV CH
+
PRESET
.
–
REPLAY ADVANCE PRESET
+
L
AUDIO
R
<
<
>
TUNING
–
CATEGORY MODE TUNING
+
m
H
M
x
TV
X
Notes
• Refer to the operating
1 Turn on the TV and DVD player.
2 Turn on the receiver.
3 Press DVD.
instructions supplied with the
TV and DVD player.
• Check the following if you
cannot listen to multi channel
sound.
– Be sure this receiver is
connected to the DVD player
via a digital connection.
– Be sure the digital audio
output of the DVD player is set
up properly.
You can also use INPUT SELECTOR on this receiver to
select “DVD”.
4 Switch the input of the TV so that an image
of the DVD is displayed.
5 Set up the DVD player.
Refer to “Quick Setup Guide” supplied with the receiver.
Tips
• Select the sound format of the
disc to be played, if necessary.
• You can select the sound field to
suit the movie/music. Refer to
page 51 for details.
Recommended sound fields:
Movie: C.ST.EX
Music: CONCERT
6 Play back the disc.
7 Adjust to a suitable volume.
8 After you have finished watching the DVD,
eject the disc and turn off the receiver, TV
and DVD player.
35US
Download from Www.Somanuals.com. All Manuals Search And Download.
To return to the previous display
Press B.
Amplifier Operations
To exit the menu
Navigating through
menus
Press AMP MENU.
Note
Some parameters and settings may appear dimmed
on the display. This means that they are either
unavailable or fixed and unchangeable.
By using the amplifier menus, you can make
various adjustments to customize the receiver.
2CH
A.F.D.
MOVIE
MUSIC
AMP MENU
AUTO CAL
1
4
7
2
5
3
6
9
1
D.TUNING
D.SKIP
MEMORY DVD MENU
ENTER
8
>10/
-
0/10
CLEAR
FM MODE
MUTING
DISPLAY
TOOLS
F
f
TV VOL
MASTER VOL
G
g
2-6
RETURN/EXIT
MENU
1 Press AMP MENU.
“1-LEVEL” appears on the display.
2 Press V/v repeatedly to select
the menu you want.
3 Press
or b to enter the
menu.
4 Press V/v repeatedly to select
the parameter you want to
adjust.
5 Press
or b to enter the
parameter.
6 Press V/v repeatedly to select
the setting you want.
The setting is entered automatically.
36US
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview of the menus
The following options are available in each
menu. For details on navigating through
Menu
[Display]
Parameters
[Display]
Settings
Initial
setting
a)
LEVEL
Test tone [T. TONE]
T. TONE Y, T. TONE N
T. TONE N
[1-LEVEL]
a)
Front speaker balance
[FRT BAL]
BAL. L +1 to BAL. L +8, BALANCE, BALANCE
BAL. R +1 to BAL. R +8
Center speaker level
[CNT LVL]
CNT –10 dB to CNT +10 dB
(1 dB step)
CNT 0 dB
SUR L 0 dB
SUR R 0 dB
SB 0 dB
Surround left speaker level
[SL LVL]
SUR L –10 dB to SUR L +10 dB
(1 dB step)
Surround right speaker level
[SR LVL]
SUR R –10 dB to SUR R +10 dB
(1 dB step)
Surround back speaker level
[SB LVL]
SB –10 dB to SB +10 dB
(1 dB step)
Sub woofer level
[SW LVL]
SW –10 dB to SW +10 dB
(1 dB step)
SW 0 dB
a)
Dynamic range compressor
[D. RANGE]
COMP. OFF, COMP. STD,
COMP. MAX
COMP. OFF
a)
EQ
Equalizer [EQ]
EQ ON, EQ OFF
EQ OFF
[2-EQ]
Front speaker bass level
[BASS LVL]
BASS –6 dB to BASS +6 dB
(1 dB step)
BASS 0 dB
Front speaker treble level
[TRE LVL]
TRE –6 dB to TRE +6 dB
(1 dB step)
TRE 0 dB
a)
SUR
[3-SUR]
Sound field selection
[S.F. SELCT]
2CH ST., A.F.D. AUTO, DOLBY PL, 2CH ST. for:
PLII MV, PLII MS, PLII GM, PLIIX TUNER,
MV, PLIIX MS, PLIIX GM, NEO6
CIN, NEO6 MUS, MULTI ST.,
SA-CD/CD,
TV,DMPORT;
C.ST.EX A, C.ST.EX B, C.ST.EX C, A.F.D. AUTO
PORTABLE, HALL, JAZZ,
CONCERT
for:
DVD, SAT,
VIDEO 1, 2, 3
Surround back decoding
mode [SB DEC]
SB OFF, SB AUTO, SB ON
SB AUTO
EFCT. STD
FM AUTO
a)
a)
Effect level [EFFECT]
EFCT. MIN, EFCT. STD,
EFCT. MAX
a)
TUNER
FM station receiving mode
[FM MODE]
FM AUTO, FM MONO
[4-TUNER]
a)
Naming preset stations
[NAME IN]
continued
37US
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu
[Display]
Parameters
[Display]
Settings
Initial
setting
AUDIO
[5-AUDIO]
Digital audio input decoding
priority [DEC. PRI.]
DEC. AUTO, DEC. PCM
DEC. AUTO
for:
SAT, DVD,
TV,
a)
VIDEO 1, 2, 3;
DEC. PCM for:
SA-CD/CD
Digital broadcast language
selection [DUAL]
DUAL M/S, DUAL M, DUAL S,
DUAL M+S
DUAL M
a)
Synchronizes audio and video A.V.SYNC. Y, A.V.SYNC. N
output [A.V. SYNC.]
A.V.SYNC. N
a)
a)
Digital audio input assignment VD1– VD1, VD1– VD2, VD1– VD3, VD1– VD1 for:
[D. ASSIGN]
VD1– DVD, VD1– TV, VD1– CD,
VIDEO 1;
DVD– VD1, DVD– VD2, DVD– VD3, DVD– DVD
DVD– DVD, DVD– SAT, DVD– TV, for: DVD;
DVD– CD, SAT– VD2, SAT– VD3, SAT– SAT for:
SAT– DVD, SAT– SAT, SAT– TV,
SAT– CD
SAT
a)
Naming inputs [NAME IN]
VIDEO
[6-VIDEO]
DIGITAL MEDIA PORT video –NONE, –VIDEO 1, –VIDEO 3,
–NONE
a)
input assignment
[DMPORT V.]
–DVD, –SAT
a)
HDMI AUDIO
[AUDIO]
AMP, TV+AMP
CTRL ON, CTRL OFF
AMP
a)
HDMI CONTROL
[CONTROL]
CTRL OFF
a)
Naming inputs [NAME IN]
38US
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu
[Display]
Parameters
[Display]
Settings
Initial
setting
a)
SYSTEM
Sub woofer
YES, NO
YES
[7-SYSTEM]
[SW SPK]
a)
a)
Front speakers
[FRT SPK]
LARGE, SMALL
LARGE, SMALL, NO
LARGE, SMALL, NO
YES, NO
LARGE
LARGE
LARGE
YES
Center speaker
[CNT SPK]
a)
Surround speakers
[SUR SPK]
a)
Surround back speaker
[SB SPK]
a)
Front speaker distance
[FRT DIST.]
DIST. 3 ft. to DIST. 23 ft.
(1 ft. step)
DIST. 10 ft.
DIST. 10 ft.
a)
Center speaker distance
[CNT DIST.]
DIST. xx ft.
between front speaker distance and
5 ft. (1 ft. step)
a)
Surround left speaker distance DIST. xx ft.
DIST. 10 ft.
DIST. 10 ft.
DIST. 10 ft.
[SL DIST.]
between front speaker distance and
15 ft. (1 ft. step)
Surround right speaker
distance
[SR DIST.]
DIST. xx ft.
between front speaker distance and
15 ft. (1 ft. step)
a)
Surround back speaker
distance
[SB DIST.]
DIST. xx ft.
between front speaker distance and
15 ft. (1 ft. step)
a)
a)
Surround speaker position
[SUR POS.]
SIDE/LO, SIDE/HI, BEHD/LO,
BEHD/HI
SIDE/LO
a)
Speaker crossover frequency
[CRS. FREQ]
CRS > 40 Hz to CRS > 160 Hz
0% dim, 40% dim, 70% dim
A.CAL YES, A.CAL NO
CRS > 100 Hz
0% dim
a)
Brightness of the display
[DIMMER]
a)
A. CAL
Auto Calibration
A.CAL NO
[8-A. CAL]
[AUTO CAL]
a)
For details, refer to the page in the parentheses.
39US
Download from Www.Somanuals.com. All Manuals Search And Download.
x D. RANGE (Dynamic range
compressor)
Adjusting the level
Lets you compress the dynamic range of the
sound track. This may be useful when you
want to watch movies at low volumes late at
night. Dynamic range compression is possible
with Dolby Digital sources only.
• COMP. OFF
(LEVEL menu)
You can use the LEVEL menu to adjust the
balance and level of each speaker. These
settings are applied to all sound fields.
Select “1-LEVEL” in the amplifier menus. For
details on adjusting the parameters, see
The dynamic range is not compressed.
• COMP. STD
The dynamic range is compressed as
intended by the recording engineer.
• COMP. MAX
The dynamic range is compressed
dramatically.
LEVEL menu parameters
x T. TONE (Test tone)
Tip
Lets you adjust the speaker levels and balance
while listening to the test tone from your
listening position. For details, see “8:
Dynamic range compressor lets you compress the
dynamic range of the soundtrack based on the
dynamic range information included in the Dolby
Digital signal.
“COMP. STD” is the standard setting, but it only
enacts light compression. Therefore, we recommend
using the “COMP. MAX” setting. This greatly
compresses the dynamic range and lets you view
movies late at night at low volumes. Unlike analog
limiters, the levels are predetermined and provide a
very natural compression.
x FRT BAL (Front speaker
balance)
Lets you adjust the balance between front left
and right speakers.
x CNT LVL (Center speaker level)
x SL LVL (Surround left speaker
level)
x SR LVL (Surround right speaker
level)
x SB LVL (Surround back speaker
level)
x SW LVL (Sub woofer level)
40US
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the equalizer
Settings for the surround
sound
(EQ menu)
(SUR menu)
You can use the EQ menu to adjust the tonal
quality (bass/treble level) of the front
speakers.
Select “2-EQ” in the amplifier menus. For
details on adjusting the parameters, see
You can use the SUR menu to select the sound
field you want for your listening pleasure.
Select “3-SUR” in the amplifier menus. For
details on adjusting the parameters, see
EQ menu parameters
SUR menu parameters
x EQ (Equalizer)
Lets you turn the equalizer on or off.
• EQ ON
The equalizer is turned on.
• EQ OFF
x S.F. SELCT (Sound field
selection)
Lets you select the sound field you want. For
details, see “Enjoying Surround Sound” (page
49).
The equalizer is turned off.
Note
x BASS LVL (Front speaker bass
The receiver lets you apply the last selected sound
field to an input whenever it is selected (Sound Field
Link). For example, if you select “HALL” for the
SA-CD/CD input, then change to a different input
and then return to SA-CD/CD, “HALL” will
automatically be applied again.
level)
x TRE LVL (Front speaker treble
level)
x SB DEC (Surround back
decoding mode)
Lets you select the surround back decoding
mode. For details, see “Using the surround
x EFFECT (Effect level)
Lets you adjust the “presence” of the surround
effect for sound fields selected with the
MOVIE or MUSIC buttons (except
“PORTABLE” sound field) and for “HP
THEA” sound field.
• EFCT. MIN
The surround effect is minimum.
• EFCT. STD
The surround effect is standard.
• EFCT. MAX
The surround effect is maximum.
41US
Download from Www.Somanuals.com. All Manuals Search And Download.
x SB ON
Using the surround back
decoding mode (SB DEC)
To decode the surround back signal regardless
a)
of the 6.1 channel decode flag , Dolby Digital
EX is applied when the output channel is 6.1.
By decoding the surround back signal of DVD
software (etc.) recorded in Dolby Digital
Surround EX, DTS-ES Matrix, DTS-ES
Discrete 6.1, etc., format, you can enjoy the
surround sound intended by the filmmakers.
Select the surround back decoding mode using
“SB DEC” on the SUR menu (page 41).
Input stream Output Surround back
channel decoding
Dolby Digital
5.1
6.1
6.1
6.1
6.1
6.1
Matrix decoder that
conforms to Dolby
Digital EX
Dolby Digital
Matrix decoder that
conforms to Dolby
Digital EX
b)
Surround EX
Types of the surround back
decoding functions
DTS 5.1
Matrix decoder that
conforms to Dolby
Digital EX
x SB AUTO
DTS-ES
Matrix 6.1
Matrix decoder that
conforms to Dolby
Digital EX
c)
When the input stream contains the 6.1
a)
channel decode flag , the appropriate
decoding is performed on the surround back
signal.
DTS-ES
Discrete 6.1
Matrix decoder that
conforms to Dolby
Digital EX
d)
Input stream Output Surround back
channel decoding
x SB OFF
Surround back decoding is not performed.
Dolby Digital
5.1
5.1
—
a)
Dolby Digital
Surround EX
6.1
Matrix decoder that
conforms to Dolby
Digital EX
A 6.1 channel decode flag is information recorded
in software such as DVDs.
A Dolby Digital DVD that includes a Surround EX
b)
b)
flag. The Dolby Corporation web page can help
you distinguish Surround EX films.
Software encoded with a flag to denote it has both
DTS-ES Matrix and 5.1 channel signals.
Software encoded with both 5.1 channel signals
and an extension stream designed for returning
those signals to 6.1 discrete channels. Discrete 6.1
channel signals are DVD specific signals not used
in movie theaters.
DTS 5.1
DTS-ES
5.1
6.1
—
DTS Matrix decoding
c)
c)
Matrix 6.1
d)
DTS-ES
Discrete 6.1
6.1
DTS Discrete
decoding
d)
Notes
• There may be no sound from the surround back
speaker in Dolby Digital EX mode. Some discs
have no Dolby Digital Surround EX flag even
though the packages have Dolby Digital EX logos.
In this case, select “SB ON”.
• You can select the surround back decoding mode
only when A.F.D. mode is selected. However, this
function is canceled when Dolby Pro Logic IIx is
selected.
42US
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings for the tuner
(TUNER menu)
Settings for the audio
(AUDIO menu)
You can use the TUNER menu to set the FM
station receiving mode and to name preset
stations.
Select “4-TUNER” in the amplifier menus.
For details on adjusting the parameters, see
You can use the AUDIO menu to make
settings for the audio to suit your preference.
Select “5-AUDIO” in the amplifier menus. For
details on adjusting the parameters, see
AUDIO menu parameters
TUNER menu parameters
x DEC. PRI. (Digital audio input
decoding priority)
Lets you specify the input mode for the digital
signal input to the DIGITAL IN and HDMI IN
jacks.
x FM MODE (FM station receiving
mode)
• FM AUTO
This receiver will decode the signal as stereo
signal when the radio station is broadcast in
stereo.
• FM MONO
This receiver will decode the signal as mono
signal regardless of the broadcast signal.
• DEC. AUTO
Automatically switches the input mode
between DTS, Dolby Digital, or PCM.
• DEC. PCM
When signals from the DIGITAL IN jack are
selected, PCM signals are given priority (to
prevent interruption when playback starts).
However, when other signals are input, there
may be no sound, depending on the format.
In this case, set this item to “DEC. AUTO”.
When signals from the HDMI IN jack are
selected, only PCM signals are output from
the connected player. When signals in any
other format are received, set this item to
“DEC. AUTO”.
x NAME IN (Naming preset
stations)
Lets you set the name of preset stations. For
details, see “Naming preset stations” (page
59).
Note
When set to “DEC. AUTO” and the sound from the
digital audio jacks (for a CD, etc.) is interrupted
when playback starts, set to “DEC. PCM”.
continued
43US
Download from Www.Somanuals.com. All Manuals Search And Download.
x DUAL (Digital broadcast
language selection)
Lets you select the language you want to listen
to during digital broadcast. This feature only
functions for Dolby Digital sources.
• DUAL M/S (Main/Sub)
Sound of the main language will be output
through the front left speaker and sound of
the sub language will be output through the
front right speaker simultaneously.
• DUAL M (Main)
Settings for the video
(VIDEO menu)
You can use the VIDEO menu to assign the
composite video input to DMPORT input and
to name inputs.
Select “6-VIDEO” in the amplifier menus. For
details on adjusting the parameters, see
Sound of the main language will be output.
• DUAL S (Sub)
Sound of the sub language will be output.
• DUAL M+S (Main + Sub)
VIDEO menu parameters
Mixed sound of both the main and sub
languages will be output.
x DMPORT V. (DIGITAL MEDIA
PORT video assignment)
Lets you assign the composite video input to
DMPORT input so that you can view the
images on the TV screen. For details, see
x A.V. SYNC. (Synchronizes audio
and video output)
• A.V.SYNC. Y (Yes) (Delay time: 68 ms)
The audio output is delayed so that the time
gap between the audio output and visual
display is minimized.
x AUDIO (HDMI AUDIO)
Lets you set the HDMI audio output from the
playback component connected to the receiver
via a HDMI connection.
• A.V.SYNC. N (No) (Delay time: 0 ms)
The audio output is not delayed.
Notes
• AMP
• This parameter is useful when you use a large LCD
The HDMI audio signals from the playback
component is only output to speakers
connected to the receiver. Multi-channel
sound can be played back as it is.
or plasma TV or a projector.
• This parameter is valid only when you use a sound
field selected with the 2CH or A.F.D. buttons.
• This parameter is not valid when
– PCM 96 kHz, DTS 96/24 or DTS 2048 signals
are input.
Note
Audio signals are not output from the TV’s
speakers.
– the receiver is performing DTS-ES Matrix 6.1
decoding.
– ANALOG DIRECT function is selected.
x D. ASSIGN
(Digital audio input assignment)
Lets you assign the digital audio input to other
input source. For details, see “Listening to
x NAME IN (Naming inputs)
Lets you set the name of inputs. For details,
44US
Download from Www.Somanuals.com. All Manuals Search And Download.
• TV+AMP
The sound is output from TV’s speaker and
the speakers connected to the receiver.
Settings for the system
(SYSTEM menu)
Notes
• The sound quality of the playback component
depends on the TV’s sound quality, such as the
number of channels, and the sampling
frequency, etc. When the TV has stereo
speakers, the sound output from the receiver is
also stereo as that of the TV, even if you play
back multi-channel source.
• When you connect the receiver to a video
component (projector, etc.), sound may not be
output from the receiver. In this case, select
“AMP”.
You can use the SYSTEM menu to set the size
and distance of the speakers connected to this
system.
Select “7-SYSTEM” in the amplifier menus.
For details on adjusting the parameters, see
SYSTEM menu parameters
x SW SPK (Sub woofer)
• YES
If you have connected a sub woofer, select
“YES”.
x CONTROL (HDMI CONTROL)
Lets you turn the HDMI CONTROL function
on or off. For details, refer to the HDMI
CONTROL Guide supplied with the receiver.
• NO
If you have not connected a sub woofer,
select “NO”. This activates the bass
redirection circuitry and outputs the LFE
signals from other speakers.
x NAME IN (Naming inputs)
Lets you set the name of inputs. For details, see
Tip
In order to take full advantage of the Dolby Digital
bass redirection circuitry, we recommend setting the
sub woofer’s cut off frequency as high as possible.
x FRT SPK (Front speakers)
• LARGE
If you connect large speakers that will
effectively reproduce bass frequencies,
select “LARGE”. Normally, select
“LARGE”. When the sub woofer is set to
“NO”, the front speakers are automatically
set to “LARGE”.
• SMALL
If the sound is distorted, or you feel a lack of
surround effects when using multi channel
surround sound, select “SMALL” to activate
the bass redirection circuitry and output the
front channel bass frequencies from the sub
woofer. When the front speakers are set to
“SMALL”, the center and surround speakers
are also automatically set to “SMALL”
(unless previously set to “NO”).
continued
45US
Download from Www.Somanuals.com. All Manuals Search And Download.
x CNT SPK (Center speaker)
• LARGE
x SB SPK (Surround back
speaker)
When the surround speakers are set to “NO”,
the surround back speaker is also
automatically set to “NO” and the setting
cannot be changed.
If you connect a large speaker that will
effectively reproduce bass frequencies,
select “LARGE”. Normally, select
“LARGE”. However, if the front speakers
are set to “SMALL”, you cannot set the
center speaker to “LARGE”.
• YES
If you have connected a surround back
speaker, select “YES”.
• SMALL
• NO
If the sound is distorted, or you feel a lack of
surround effects when using multi channel
surround sound, select “SMALL” to activate
the bass redirection circuitry and output the
center channel bass frequencies from the
front speakers (if set to “LARGE”) or sub
woofer.
If you have not connected a surround back
speaker, select “NO”.
Tip
The “LARGE” and “SMALL” settings for each
speaker determine whether the internal sound
processor will cut the bass signal from that channel.
When the bass is cut from a channel, the bass
redirection circuitry sends the corresponding bass
frequencies to the sub woofer or other “LARGE”
speakers.
However, since bass sounds have a certain amount
of directionality, it is best not to cut them, if
possible. Therefore, even when using small
speakers, you can set them to “LARGE” if you want
to output the bass frequencies from that speaker. On
the other hand, if you are using a large speaker, but
prefer not to have bass frequencies output from that
speaker, set it to “SMALL”.
• NO
If you have not connected a center speaker,
select “NO”. The sound of the center
channel will be output from the front
speakers.
x SUR SPK (Surround speakers)
The surround back speaker will be set to the
same setting.
• LARGE
If you connect large speakers that will
effectively reproduce bass frequencies,
select “LARGE”. Normally, select
“LARGE”. However, if the front speakers
are set to “SMALL”, you cannot set the
surround speakers to “LARGE”.
• SMALL
If the overall sound level is lower than you prefer,
set all speakers to “LARGE”. If there is not enough
bass, you can use the equalizer to boost the bass
levels. For details, see page 37.
If the sound is distorted, or you feel a lack of
surround effects when using multi channel
surround sound, select “SMALL” to activate
the bass redirection circuitry and output the
surround channel bass frequencies from the
sub woofer or other “LARGE” speakers.
• NO
If you have not connected surround
speakers, select “NO”.
46US
Download from Www.Somanuals.com. All Manuals Search And Download.
x FRT DIST. (Front speaker
distance)
x SB DIST. (Surround back
speaker distance)
Lets you set the distance from your listening
position to the front speakers (A). If both
front speakers are not placed an equal distance
from your listening position, set the distance as
the average distance between the front
speakers.
Lets you set the distance from your listening
position to the surround back speaker.
Surround back speaker distance should be set
from a distance equal to the front speaker
distance (A) to a distance 15 feet closer to
your listening position (E).
Tip
B
The receiver lets you to input the speaker position in
terms of distance. However, it is not possible to set
the center speaker further than the front speakers.
Also, the center speaker cannot be set more than
5 feet closer from the front speakers.
A
A
30˚ 30˚
100˚-120˚
100˚-120˚
C
D
Likewise, the surround and surround back speakers
can not be set further away from the listening
position than the front speakers. And they can be no
more than 15 feet closer. This is because incorrect
speaker placement is not conducive to the
enjoyment of surround sound.
E
Please note that, setting the speaker distance closer
than the actual location of the speakers will cause a
delay in the output of the sound from that speaker. In
other words, the speaker will sound like it is further
away.
For example, setting the center speaker distance
3-6 feet closer than the actual speaker position will
create a fairly realistic sensation of being “inside”
the screen. If you cannot obtain a satisfactory
surround effect because the surround speakers are
too close, setting the surround speaker distance
closer (shorter) than the actual distance will create a
larger sound stage.
x CNT DIST. (Center speaker
distance)
Lets you set the distance from your listening
position to the center speaker. Center speaker
distance should be set from a distance equal to
the front speaker distance (A) to a distance 5
feet closer to your listening position (B).
x SL DIST. (Surround left speaker
distance)
Lets you set the distance from your listening
position to the surround left speaker. Surround
left speaker distance should be set from a
distance equal to the front speaker distance
(A) to a distance 15 feet closer to your
listening position (C).
Adjusting these parameter while listening to the
sound often results in much better surround sound.
Give it a try!
x SR DIST. (Surround right
speaker distance)
Lets you set the distance from your listening
position to the surround right speaker.
Surround right speaker distance should be set
from a distance equal to the front speaker
distance (A) to a distance 15 feet closer to
your listening position (D).
continued
47US
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
x SUR POS.
Surround speaker position is designed specifically
for implementation of the Cinema Studio EX modes.
For other sound fields, speaker position is not so
critical.
Those sound fields were designed under the premise
that the surround speakers would be located behind
the listening position, but presentation remains
fairly consistent even with the surround speakers
positioned at a rather wide angle. However, if the
speakers are pointing toward the listener from the
immediate left and right of the listening position, the
surround effects become unclear unless set to
“SIDE/LO” or “SIDE/HI”.
(Surround speaker position)
Lets you specify the location of your surround
speakers for proper implementation of the
surround effects in the Cinema Studio EX
available when the surround speakers are set to
“NO” (page 39).
Nevertheless, each listening environment has many
variables, such as wall reflections, and you may
obtain better results using “BEHD/HI” if your
speakers are located high above the listening
position, even if they are located to the immediate
left and right.
Therefore, although it may result in a setting
contrary to the above explanation, we recommend
that you play back multi channel surround encoded
software and select the setting that provides a good
sense of spaciousness and that best succeeds in
forming a cohesive space between the surround
sound from the surround speakers and the sound of
the front speakers. If you are not sure which sounds
best, select “BEHD/LO” or “BEHD/HI” and then
use the speaker distance parameter and speaker level
adjustments to obtain proper balance.
x CRS. FREQ (Speaker crossover
frequency)
Lets you set the bass crossover frequency of
the speakers that have been set to “SMALL”
on the SYSTEM menu. This setup item is only
available when at least one speaker is set to
“SMALL” and the corresponding speaker
indicator flashes on the display.
• SIDE/LO
Select if the location of your surround
speakers corresponds to sections A and C.
• SIDE/HI
Select if the location of your surround
speakers corresponds to sections A and D.
• BEHD/LO
x DIMMER (Brightness of the
display)
Lets you adjust the brightness in 3 steps.
Select if the location of your surround
speakers corresponds to sections B and C.
• BEHD/HI
Select if the location of your surround
speakers corresponds to sections B and D.
48US
Download from Www.Somanuals.com. All Manuals Search And Download.
Calibrating the
appropriate settings
automatically
(A. CAL menu)
Enjoying Surround Sound
Enjoying Dolby Digital
and DTS Surround sound
(AUTO FORMAT DIRECT)
For details, see “7: Calibrating the appropriate
The Auto Format Direct (A.F.D.) mode allows
you to listen to higher fidelity sound and select
the decoding mode for listening to a 2 channel
stereo sound as multi channel sound.
VIDEO 1 VIDEO 2 VIDEO 3
DVD
SAT
2CH
TV
SA-CD/CD TUNER
A.F.D.
MOVIE
MUSIC
A.F.D.
AMP MENU
1
2
3
Press A.F.D. repeatedly to select
the sound field you want.
For details, see “Types of A.F.D. mode” (page
50).
continued
49US
Download from Www.Somanuals.com. All Manuals Search And Download.
Types of A.F.D. mode
Decoding
mode
A.F.D. mode
[Display]
Multi channel
audio after
decoding
Effect
(Detecting
automatically) [A.F.D. AUTO]
A.F.D. AUTO
(Detecting
automatically)
Presents the sound as it was recorded/
encoded without adding any surround
effects. However, this receiver will
generate a low frequency signal for output
to the sub woofer when there is no LFE
signals.
Dolby Pro Logic PRO LOGIC
[DOLBY PL]
4 channel
5 channel
Performs Dolby Pro Logic decoding. The
source recorded in 2 channel format is
decoded into 4.1 channels.
Dolby Pro Logic PRO LOGIC II MOVIE
Performs Dolby Pro Logic II Movie mode
decoding. This setting is ideal for movies
encoded in Dolby Surround. In addition,
this mode can reproduce sound in 5.1
channel for watching videos of overdubbed
or old movies.
II
[PLII MV]
PRO LOGIC II MUSIC
[PLII MS]
5 channel
5 channel
Performs Dolby Pro Logic II Music mode
decoding. This setting is ideal for normal
stereo sources such as CDs.
PRO LOGIC II GAME
[PLII GM]
Performs Dolby Pro Logic II Game mode
decoding. This setting is ideal for game
softwares.
Dolby Pro Logic PRO LOGIC IIx MOVIE 6 channel
Performs Dolby Pro Logic IIx Movie mode
decoding. This setting expands Dolby Pro
Logic II Movie or Dolby Digital 5.1 to
discrete 6.1 movie channels.
IIx*
[PLIIX MV]
PRO LOGIC IIx MUSIC 6 channel
[PLIIX MS]
Performs Dolby Pro Logic IIx Music mode
decoding. This setting is ideal for normal
stereo sources such as CDs.
PRO LOGIC IIx GAME 6 channel
[PLIIX GM]
Performs Dolby Pro Logic IIx Game mode
decoding.
Neo:6
Neo:6 Cinema
[NEO6 CIN]
6 channel
Performs DTS Neo:6 Cinema mode
decoding.
Neo:6 Music
[NEO6 MUS]
6 channel
Performs DTS Neo:6 Music mode
decoding. This setting is ideal for normal
stereo sources such as CDs.
(Multi Stereo) MULTI STEREO
[MULTI ST.]
(Multi Stereo)
Outputs 2 channel left/right signals from
all speakers. However, sound may not be
output from certain speakers depending on
the speaker settings.
* You cannot select this decoding mode if there is no surround back speaker connected to the receiver.
50US
Download from Www.Somanuals.com. All Manuals Search And Download.
If you connect a sub woofer
This receiver will generate a low frequency
signal for output to the sub woofer when there
is no LFE signal, which is a low-pass sound
effect output from a sub woofer to a 2 channel
signal. However, the low frequency signal is
not generated for “NEO6 CIN” or “NEO6
MUS” when all speakers are set to “LARGE”.
Selecting a pre-
programmed sound field
You can take advantage of surround sound
simply by selecting one of the receiver’s pre-
programmed sound fields. They bring the
exciting and powerful sound of movie theaters
and concert halls into your home.
Notes
• This function does not work when ANALOG
SAT
TV
SA-CD/CD TUNER
DIRECT is selected.
• DTS Neo:6 does not work for DTS 2CH audio, the
sound is played back as 2 channel.
• Dolby Pro Logic IIx decoding does not function for
DTS format signals or for signals with a sampling
frequency of more than 48 kHz.
2CH
A.F.D.
MOVIE
MUSIC
2CH
MUSIC
MOVIE
AMP MENU
AUTO CAL
1
4
2
5
3
6
A.F.D.
Tip
When a multi channel signal is input, only Dolby
Pro Logic IIx decoding is effective. When you select
decoding modes other than Dolby Pro Logic IIx,
multi channel sound (being encoded) is output.
Press MOVIE repeatedly to select a
sound field for movies or press
MUSIC repeatedly to select a
sound field for music.
For details, see “Types of sound field
continued
51US
Download from Www.Somanuals.com. All Manuals Search And Download.
Types of sound field available
Sound field
for
Sound field
[Display]
Effect
Movie
CINEMA STUDIO EX A
DCS [C.ST.EX A]
Reproduces the sound characteristics of the Sony Pictures
Entertainment “Cary Grant Theater” cinema production
studio. This is a standard mode, great for watching almost any
type of movie.
CINEMA STUDIO EX B
DCS [C.ST.EX B]
Reproduces the sound characteristics of the Sony Pictures
Entertainment “Kim Novak Theater” cinema production
studio. This mode is ideal for watching science-fiction or
action movies with lots of sound effects.
CINEMA STUDIO EX C
DCS [C.ST.EX C]
Reproduces the sound characteristics of the Sony Pictures
Entertainment scoring stage. This mode is ideal for watching
musicals or films where orchestra music is featured in the
soundtrack.
Music
PORTABLE AUDIO
[PORTABLE]
Reproduces a clear enhanced sound image from your portable
audio device. This mode is ideal for MP3 and other
compressed music.
HALL [HALL]
Reproduces the acoustics of a classical concert hall.
Reproduces the acoustics of a jazz club.
JAZZ CLUB [JAZZ]
LIVE CONCERT
[CONCERT]
Reproduces the acoustics of a 300-seat live house.
Headphone*
HEADPHONE 2CH
[HP 2CH]
This mode is selected automatically if you use headphones
selected. Standard 2 channel stereo sources completely bypass
the sound field processing and multi channel surround formats
are downmixed to 2 channels.
HEADPHONE DIRECT
[HP DIR]
Outputs the analog signals without processing by the tone,
sound field, etc.
HEADPHONE THEATER This mode is selected automatically if you use headphones
DCS [HP THEA]
when a sound field for movie/music is selected. It allows you
to experience a theater-like environment while listening
through a pair of headphones.
* You can only select this sound field if the headphones are connected to the receiver.
52US
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
About DCS (Digital Cinema
Sound)
• The effects provided by the virtual speakers may
cause increased noise in the playback signal.
• When listening with sound fields that employ the
virtual speakers, you will not be able to hear any
sound coming directly from the surround speakers.
• This function does not work when:
– ANALOG DIRECT is selected.
Sound fields with DCS mark use DCS
technology.
DCS is a unique sound reproduction
technology for home theater developed by
Sony, in cooperation with Sony Pictures
Entertainment, for enjoying the exciting and
powerful sound of movie theaters at home.
With this “Digital Cinema Sound” developed
by integrating a DSP (Digital signal processor)
and measured data, the ideal sound field
intended by film makers can be experienced at
home.
– signals with a sampling frequency of more than
48 kHz is input.
• When one of the sound fields for music is selected,
no sound is output from the sub woofer if all the
speakers are set to “LARGE” on the SYSTEM
menu. However, the sound will be output from the
sub woofer if
– the digital input signal contains LFE signals.
– the front and surround speakers are set to
“SMALL”.
About CINEMA STUDIO EX
modes
– the sound field for movie is selected.
CINEMA STUDIO EX modes are suitable for
watching motion picture DVDs (etc.), with
multi channel surround effects. You can
reproduce the sound characteristics of Sony
Pictures Entertainment’s dubbing studio in
your home.
Tip
You can identify the encoding format of DVD
software, etc., by looking at the logo on the package.
•
•
: Dolby Digital discs
: Dolby Surround
encoded programs
: DTS Digital Surround encoded
•
The CINEMA STUDIO EX modes consist of
the following three elements.
programs
• Virtual Multi Dimension
Creates 5 sets of virtual speakers from a
single pair of actual surround speakers.
• Screen Depth Matching
Creates the sensation that the sound is
coming from inside the screen like in
theaters.
To turn off the surround effect
for movie/music
Press 2CH to select “2CH ST.” or press A.F.D.
repeatedly to select “A.F.D. AUTO”.
• Cinema Studio Reverberation
Reproduces the type of reverberation found
in theaters.
The CINEMA STUDIO EX modes integrate
these three elements simultaneously.
53US
Download from Www.Somanuals.com. All Manuals Search And Download.
Using only the front
speakers
Listening to the sound
without any adjustment
(ANALOG DIRECT)
(2CH STEREO)
In this mode, the receiver outputs the sound
from the front left/right speakers only. There is
no sound from the sub woofer.
Standard 2 channel stereo sources completely
bypass the sound field processing and multi
channel surround formats are downmixed to 2
channel.
You can switch the audio of the selected input
to two channel analog input. This function
enables you to enjoy high quality analog
sources.
When using this function, only the volume and
front speaker balance can be adjusted.
?/1
MASTER VOLUME
SAT
TV
SA-CD/CD TUNER
TUNING MODE
TUNING
DISPLA
Y
INPUT MODE
INPUT SELECTOR
SPEAKERS
(OFF/A/B)
2CH
A.F.D.
MOVIE
MUSIC
AUTO CAL MIC
PHONES
MEMORY/ CATEGORY
ENTER MODE
CATEGORY
2CH
A.F.D.
MOVIE
MUSIC
AUTO CAL
DIRECT
2CH
VIDEO
VIDEO
3
IN/PORTABLE AV IN
L
AUDIO
R
AMP MENU
AUTO CAL
1
4
2
5
3
6
Sound field
buttons
1 2
Press 2CH.
Note
No sound is output from the sub woofer in the 2CH
STEREO mode. To listen to 2 channel stereo
sources using the front left/right speakers and a sub
1 Turn INPUT SELECTOR on the
receiver to select the input you
want to listen to in analog
audio.
You can also use the input buttons on the
remote.
2 Press DIRECT on the receiver.
The analog audio is output.
To cancel ANALOG DIRECT
Press DIRECT on the receiver again.
You can also press any sound field buttons.
Notes
• When headphones are connected, “HP DIR”
appears on the display.
• This function is not available when DMPORT
input is selected.
54US
Download from Www.Somanuals.com. All Manuals Search And Download.
Resetting sound fields to
the initial settings
Be sure to use the buttons on the receiver for
this operation.
Tuner Operations
Listening to FM/AM radio
You can listen to FM and AM broadcasts
through the built-in tuner. Before operation,
make sure you have connected the FM and
AM antennas (aerials) to the receiver (page
25).
1,2
?/1
MASTER VOLUME
TUNING MODE
TUNING
DISPLA
Y
INPUT MODE
Tip
INPUT SELECTOR
SPEAKERS
(OFF/A/B)
The tuning scale for direct tuning differs depending
on the area code as shown in the following table. For
details on area codes, see page 3.
AUTO CAL MIC
PHONES
MEMORY/ CATEGORY
ENTER MODE
CATEGORY
2CH
A.F.D.
MOVIE
MUSIC
AUTO CAL
DIRECT
VIDEO
VIDEO
3
IN/PORTABLE AV IN
L
AUDIO
R
Area code
FM
AM
U, CA
100 kHz
10 kHz*
2
1 Press ?/1 to turn off the power.
2 While holding down 2CH, press
?/1.
“S.F. CLR.” appears on the display and
all sound fields are reset to their initial
setting.
55US
Download from Www.Somanuals.com. All Manuals Search And Download.
In case of poor FM stereo
reception
Automatic tuning
If the FM stereo reception is poor and “ST”
flashes on the display, select monaural audio
so that the sound will be less distorted.
Press FM MODE repeatedly until the
“MONO” indicator lights up on the display.
To return to stereo mode, press FM MODE
repeatedly until the “MONO” indicator on the
display does not light up.
VIDEO 1 VIDEO 2 VIDEO 3
DVD
SAT
2CH
TV
SA-CD/CD TUNER
1
A.F.D.
MOVIE
MUSIC
AMP MENU
AUTO CAL
1
4
7
2
5
3
6
9
D.TUNING
D.SKIP
8
Direct tuning
MEMORY DVD MENU
ENTER
>10/
-
0/10
FM MODE
CLEAR
FM MODE
Enter the frequency of a station directly by
using the numeric buttons.
MUTING
DISPLAY
TOOLS
F
f
TV VOL
SYSTEM STANDBY
MASTER VOL
VIDEO 1 VIDEO 2 VIDEO 3
DVD
G
g
SAT
2CH
TV
SA-CD/CD TUNER
1
A.F.D.
MOVIE
MUSIC
RETURN/EXIT
TV CH –
MENU
– CATEGORY +
TV CH +
PRESET – REPLAY ADVANCE PRESET +
AMP MENU
AUTO CAL
.
<
<
>
1
4
7
2
5
3
6
9
TUNING – CATEGORY MODE TUNING +
m
H
M
x
2
D.TUNING
D.SKIP
MEMORY DVD MENU
ENTER
3
TV
8
2
4
X
>10/
-
0/10
CLEAR
FM MODE
1 Press TUNER repeatedly to
select the FM or AM band.
1 Press TUNER repeatedly to
select the FM or AM band.
2 Press TUNING + or TUNING –.
You can also use INPUT SELECTOR on
the receiver.
Press TUNING + to scan from low to
high; press TUNING – to scan from high
to low.
2 Press D.TUNING.
The receiver stops scanning whenever a
station is received.
3 Press the numeric buttons to
enter the frequency.
Using the controls on the
receiver
Example 1: FM 102.50 MHz
Select 1 b 0 b 2 b 5 b 0
Example 2: AM 1,350 kHz
1 Turn INPUT SELECTOR to select the FM
or AM band.
Select 1 b 3 b 5 b 0
2 Press TUNING MODE repeatedly to select
“AUTO T.”.
3 Turn TUNING +/–.
If you have tuned in an AM station, adjust
the direction of the AM loop antenna
(aerial) for optimum reception.
4 Press ENTER.
You can also use MEMORY/ENTER on
the receiver.
56US
Download from Www.Somanuals.com. All Manuals Search And Download.
If you cannot tune in a station
Make sure you have entered the right
still cannot tune in a station, the frequency is
not used in your area.
Presetting radio stations
You can preset up to 30 FM stations and 30
AM stations. Then you can easily tune in the
stations you often listen to.
Presetting radio stations
SYSTEM STANDBY
VIDEO 1 VIDEO 2 VIDEO 3
DVD
SAT
2CH
TV
SA-CD/CD TUNER
1
A.F.D.
MOVIE
MUSIC
AMP MENU
AUTO CAL
1
4
7
2
5
3
6
9
D.TUNING
D.SKIP
MEMORY DVD MENU
ENTER
4
8
>10/
-
0/10
CLEAR
FM MODE
3,5
MUTING
DISPLAY
TOOLS
F
f
TV VOL
MASTER VOL
G
g
RETURN/EXIT
TV CH –
MENU
– CATEGORY +
TV CH +
PRESET
+/–
PRESET – REPLAY ADVANCE PRESET +
.
<
<
>
TUNING – CATEGORY MODE TUNING +
m
H
M
1 Press TUNER repeatedly to
select the FM or AM band.
You can also use INPUT SELECTOR on
the receiver.
2 Tune in the station that you
want to preset using Automatic
Switch the FM reception mode, if
continued
57US
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Press MEMORY.
Tuning to preset stations
You can also use MEMORY/ENTER on
the receiver.
SYSTEM STANDBY
VIDEO 1 VIDEO 2 VIDEO 3
DVD
“MEMORY” lights up for a few seconds.
“MEMORY” goes out.
SAT
2CH
TV
SA-CD/CD TUNER
1
A.F.D.
MOVIE
MUSIC
4 Press the numeric buttons to
AMP MENU
AUTO CAL
1
4
7
2
5
3
6
9
select a preset number.
You can also press PRESET + or
PRESET – to select a preset number.
If “MEMORY” goes out before you
select the preset number, start again from
Numeric
buttons
D.TUNING
D.SKIP
MEMORY DVD MENU
ENTER
8
>10/
-
0/10
CLEAR
FM MODE
ENTER
MUTING
DISPLAY
TOOLS
F
f
TV VOL
MASTER VOL
5 Press ENTER.
G
g
You can also use MEMORY/ENTER on
the receiver.
RETURN/EXIT
TV CH –
MENU
– CATEGORY +
TV CH +
The station is stored as the selected preset
number.
If “MEMORY” goes out before you press
ENTER, start again from step 3.
PRESET – REPLAY ADVANCE PRESET +
2
.
<
<
>
TUNING – CATEGORY MODE TUNING +
m
H
M
1 Press TUNER repeatedly to
another station.
select the FM or AM band.
2 Press PRESET + or PRESET –
repeatedly to select the preset
station you want.
Each time you press the button, you can
select a preset station as follows:
01
02
03
30
04
29
05
28
...
27
You can also press the numeric buttons to
select the preset station you want. Then,
press ENTER to enter the selection.
Using the controls on the
receiver
1 Turn INPUT SELECTOR to select the FM
or AM band.
2 Press TUNING MODE repeatedly to select
“PRESET T.”.
3 Turn TUNING +/– to select the preset
station you want.
58US
Download from Www.Somanuals.com. All Manuals Search And Download.
To create an index name
Naming preset stations
1 Use V/v/B/b to create an index name.
Press V/v to select a character, then press
B/b to move the cursor to the next position.
SYSTEM STANDBY
VIDEO 1 VIDEO 2 VIDEO 3
DVD
If you made a mistake
SAT
2CH
TV
SA-CD/CD TUNER
1
3
Press B/b until the character you want to
change flashes, then press V/v to select the
correct character.
A.F.D.
MOVIE
MUSIC
AMP MENU
AUTO CAL
1
4
7
2
5
3
6
9
Tip
You can select the character type as follows by
pressing V/v.
Alphabet (upper case) t Numbers t Symbols
D.TUNING
D.SKIP
MEMORY DVD MENU
ENTER
8
>10/
-
0/10
CLEAR
FM MODE
2 Press
.
MUTING
DISPLAY
TOOLS
The entered name is registered.
F
f
TV VOL
MASTER VOL
G
g
4-7
RETURN/EXIT
MENU
1 Press TUNER repeatedly to
select the FM or AM band.
You can also use INPUT SELECTOR on
the receiver.
2 Tune in the preset station you
want to create an index name
3 Press AMP MENU.
“1-LEVEL” appears on the display.
4 Press V/v repeatedly to select
“4-TUNER”.
5 Press
or b to enter the
menu.
6 Press V/v repeatedly to select
“NAME IN”.
7 Press
or b to enter the
parameter.
The cursor flashes and you can select a
character. Follow the procedure given in
59US
Download from Www.Somanuals.com. All Manuals Search And Download.
To activate XM Satellite Radio
Once you have installed the XM Mini-Tuner
Dock, inserted the XM Mini-Tuner, connected
Listening to the XM Radio
®
the XM Dock to your XM Ready home audio
About XM Satellite Radio
system, and installed the antenna, you are
ready to subscribe and begin receiving XM
programming. There are three places to find
your eight character XM Radio ID: on the XM
Mini-Tuner, on the XM Mini-Tuner package,
and on XM Channel 0. Record the Radio ID in
the following eight squares for reference.
ssssssss
XM Satellite Radio offers an extraordinary
variety of commercial-free music, plus the
best in sports, news, talk and entertainment.
XM is broadcast in superior digital audio from
coast to coast. From rock to reggae, from
classical to hip hop, XM has something for
every music fan. XM’s dedication to playing
the richest selection of music is matched by its
passion for live sporting events, talk radio, up-
to-the-minute news, stand-up comedy,
children’s programming, and much more. For
U.S. customers, information about XM
Satellite Radio is available online at
Note
The XM radio ID does not use the letters “I”, “O”,
“S” or “F”. Activate your XM Satellite Radio
service in the U.S. online at http://
activate.xmradio.com or call 1-800-XM-RADIO (1-
800-967-2346). You will need a major credit card.
XM will send a signal from the satellites to activate
the full channel lineup. Activation normally takes 10
to 15 minutes, but during peak busy periods you may
need to keep your XM Ready home audio system on
for up to an hour. When you can access the full
channel lineup on your XM Ready home audio
system you are done. For more information or to
subscribe in Canada, visit XM on the Web at
1-877-GET-XMSR (1-877-438-9677).
information about XM Canada is online at
XM Satellite Radio Terms and
Conditions
Hardware and required monthly subscription
sold separately. Other fees and taxes,
including a one-time activation fee may apply.
Subscription fee is consumer only. All fees
and programming subject to change. Channels
with frequent explicit language are indicated
with an XL. Channel blocking is available for
XM radio receivers by calling 1-800-
XMRADIO (US residents) and 1-877-GET-
XMSR (Canadian residents).
For a full listing of the XM commercial-free
channels and advertising-supported channels,
visit lineup.xmradio.com (US residents) or
xmradio.ca (Canadian residents).
Subscriptions subject to Customer Agreement
available at xmradio.com (US residents) and
xmradio.ca (Canadian residents). Only
available in the 48 contiguous United States
and Canada.
©2006 XM Satellite Radio Inc. All rights
reserved. All other trademarks are the property
of their respective owners.
60US
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the XM Radio
Checking the XM Radio ID
Before operating the system, connect the XM
Connect-and-Play antenna to the XM jack.
VIDEO 1 VIDEO 2 VIDEO 3
DVD
SAT
2CH
TV
SA-CD/CD TUNER
XM jack
1
A.F.D.
MOVIE
MUSIC
AMP MENU
AUTO CAL
DIGITAL
DVD IN
VIDEO 2/BD IN
1
4
7
2
5
3
6
9
(ASSIGNABLE)
OPTICAL
ANTENNA
SAT
IN
HDMI
AM
D.TUNING
D.SKIP
MEMORY DVD MENU
ENTER
VIDEO
IN
1
XM
8
COAXIAL
DVD
IN
>10/
-
0/10
CLEAR
FM MODE
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN
DMPORT
DVD
MUTING
DISPLAY
TOOLS
F
f
L
L
L
TV VOL
MASTER VOL
G
g
R
R
R
IN
IN
AUDIO IN
AUDIO OUT AUDIO IN
SA-CD
/
CD
TV
SAT
VIDEO 1
RETURN/EXIT
TV CH –
MENU
– CATEGORY +
TV CH +
PRESET – REPLAY ADVANCE PRESET +
.
<
<
>
TUNING – CATEGORY MODE TUNING +
2
m
H
M
x
Note
TV
To ensure optimal reception of XM’s satellite signal,
move your antenna to various window locations
around your home to see where the best reception
will be received. Most XM customers place the
antenna in a south-facing window with a clear view
to the sky.
X
1 Press TUNER repeatedly to
select “XM RADIO”.
You can also use INPUT SELECTOR on
the receiver.
2 Press TUNING + or TUNING – to
select channel 0.
You can also press TUNING MODE on
the receiver to select “AUTO T.”, and
then turn TUNING +/– to select channel
0.
3 Check the XM Radio ID on the
display and write it in the space
provided here.
ID:_____________________________
If you cannot read the characters or
numbers on the display, refer to the
following table.
continued
61US
Download from Www.Somanuals.com. All Manuals Search And Download.
Display
Description
Receiving XM Radio broadcasts
2 (two)
VIDEO 1 VIDEO 2 VIDEO 3
DVD
5 (five)
6 (six)
SAT
2CH
TV
SA-CD/CD TUNER
1
8 (eight)
A.F.D.
MOVIE
MUSIC
0 (zero)
AMP MENU
AUTO CAL
1
4
7
2
5
3
6
9
A
B
D
G
H
K
M
Q
Z
D.TUNING
D.SKIP
MEMORY DVD MENU
ENTER
8
>10/
-
0/10
CLEAR
FM MODE
MUTING
DISPLAY
TOOLS
F
f
TV VOL
MASTER VOL
G
g
RETURN/EXIT
TV CH –
MENU
– CATEGORY +
TV CH +
PRESET – REPLAY ADVANCE PRESET +
.
<
<
>
TUNING – CATEGORY MODE TUNING +
m
H
M
x
2
TV
X
1 Press TUNER repeatedly to
select “XM RADIO”.
You can also use INPUT SELECTOR on
the receiver.
2 Press TUNING + or TUNING – to
select a channel.
You can also press TUNING MODE on
the receiver to select “AUTO T.”, and
then turn TUNING +/– to select a
channel.
62US
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Press CATEGORY + or
CATEGORY – to select the
category you want.
Selecting channels from a
category (CATEGORY TUNING)
The category is selected and the channel
with the lowest number in the specified
category is selected.
You can select a channel from one category or
all the categories by changing the category
mode.
VIDEO 1 VIDEO 2 VIDEO 3
DVD
4 Press TUNING + or TUNING – to
select the channel.
SAT
2CH
TV
SA-CD/CD TUNER
1
You can also press TUNING MODE on
the receiver to select “AUTO T.”, and
then turn TUNING +/– to select the
channel.
A.F.D.
MOVIE
MUSIC
AMP MENU
AUTO CAL
1
4
7
2
5
3
6
9
Notes
D.TUNING
D.SKIP
8
• When you select a channel in the “ONE CAT”
mode, the channel you selected may not be the one
in the category you want. This is because one
channel may belong to more than one category.
• If you press CATEGORY + or CATEGORY – in
the “ALL CAT” mode, the first channel of the next
or previous category is selected (CATEGORY
SKIP).
MEMORY DVD MENU
ENTER
>10/
-
0/10
CLEAR
FM MODE
MUTING
TOOLS
DISPLAY
F
f
TV VOL
MASTER VOL
G
g
RETURN/EXIT
TV CH –
MENU
3
2
– CATEGORY +
TV CH +
PRESET – REPLAY ADVANCE PRESET +
Selecting channels by inputting
the channel number directly
(DIRECT TUNING)
.
<
<
>
TUNING – CATEGORY MODE TUNING +
m
H
M
x
4
TV
X
SYSTEM STANDBY
VIDEO 1 VIDEO 2 VIDEO 3
DVD
SAT
2CH
TV
SA-CD/CD TUNER
1 Press TUNER repeatedly to
1
select “XM RADIO”.
A.F.D.
MOVIE
MUSIC
You can also use INPUT SELECTOR on
the receiver.
AMP MENU
AUTO CAL
1
4
7
2
5
3
6
9
2 Press CATEGORY MODE
repeatedly to select the “ONE
CAT”.
D.TUNING
D.SKIP
MEMORY DVD MENU
ENTER
3
8
2
4
>10/
-
0/10
CLEAR
FM MODE
• ALL CAT: You can select a channel
from all the categories. The initial
setting is “ALL CAT”.
• ONE CAT: You can select a channel
from one category. “CAT” is displayed
on the display when you set to “ONE
CAT” mode.
1 Press TUNER repeatedly to
select “XM RADIO”.
You can also use INPUT SELECTOR on
the receiver.
2 Press D.TUNING.
continued
63US
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Press the numeric buttons to
enter the channel number.
Presetting XM Radio
stations
You can select the channels you want directly
by presetting them using the preset numbers.
You can preset up to 30 XM Radio channels.
4 Press ENTER.
You can also use MEMORY/ENTER on
the receiver.
The selected channel is tune in.
Displaying the XM-RADIO
information on the front panel
display
Presetting channels using the
preset numbers
DISPLAY
SYSTEM STANDBY
VIDEO 1 VIDEO 2 VIDEO 3
DVD
SAT
2CH
TV
SA-CD/CD TUNER
?/1
MASTER VOLUME
TUNING MODE
TUNING
DISPLA
Y
INPUT MODE
1
INPUT SELECTOR
A.F.D.
MOVIE
MUSIC
SPEAKERS
(OFF/A/B)
AUTO CAL MIC
PHONES
MEMORY/ CATEGORY
ENTER MODE
AMP MENU
AUTO CAL
CATEGORY
2CH
A.F.D.
MOVIE
MUSIC
AUTO CAL
DIRECT
VIDEO
VIDEO
3
IN/PORTABLE AV IN
1
4
7
2
5
3
6
9
L
AUDIO
R
D.TUNING
D.SKIP
MEMORY DVD MENU
ENTER
4
8
Press DISPLAY on the receiver
repeatedly.
>10/
-
0/10
CLEAR
FM MODE
3,5
MUTING
DISPLAY
TOOLS
Each time you press DISPLAY while tuning in
the channel, the display changes cyclically as
follows:
Channel name t Channel number t
Category t Artist name/Feature t
Song/Program title t Sound field type
F
f
TV VOL
MASTER VOL
G
g
RETURN/EXIT
TV CH –
MENU
– CATEGORY +
TV CH +
PRESET
+/–
PRESET – REPLAY ADVANCE PRESET +
.
<
<
>
Tip
TUNING – CATEGORY MODE TUNING +
m
H
M
The preset number is always displayed at the right
end of the display.
1 Press TUNER repeatedly to
select “XM RADIO”.
You can also use INPUT SELECTOR on
the receiver.
2 Tune in the channel you want to
preset.
For details on selecting channels, see
3 Press MEMORY.
You can also use MEMORY/ENTER on
the receiver.
64US
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Press the numeric buttons to
2 Press PRESET + or PRESET –
repeatedly to select the preset
channel you want.
enter the preset number.
You can also select the number by
pressing PRESET + or PRESET –.
You can also turn TUNING +/– on the
receiver.
Preset numbers from 1 to 30 are available,
and channel 1 is preset for all the preset
numbers when you purchase the receiver.
You can also press the numeric buttons to
select the preset channel you want. Then
press ENTER to enter the selection.
You can also press TUNING MODE on
the receiver to select “PRESET T.”, and
then turn TUNING +/–.
You can select preset channels from 1 to
30.
5 Press ENTER.
You can also use MEMORY/ENTER on
the receiver.
Note
The preset channel information will be updated
depending on the service provided by the XM
Satellite Radio Inc. that you have subscribed to.
another channel.
Selecting the channel by using
the preset numbers
SYSTEM STANDBY
VIDEO 1 VIDEO 2 VIDEO 3
DVD
SAT
2CH
TV
SA-CD/CD TUNER
1
A.F.D.
MOVIE
MUSIC
AMP MENU
AUTO CAL
1
4
7
2
5
3
6
9
Numeric
buttons
D.TUNING
D.SKIP
MEMORY DVD MENU
ENTER
8
>10/
-
0/10
CLEAR
FM MODE
ENTER
MUTING
DISPLAY
TOOLS
F
f
TV VOL
MASTER VOL
G
g
RETURN/EXIT
TV CH –
MENU
– CATEGORY +
TV CH +
PRESET – REPLAY ADVANCE PRESET +
.
<
<
>
2
TUNING – CATEGORY MODE TUNING +
m
H
M
1 Press TUNER repeatedly to
select “XM RADIO”.
continued
65US
Download from Www.Somanuals.com. All Manuals Search And Download.
XM Radio messages list
Message
appears
Explanation
Remedies
ANTENNA
UPDATING
The XM antenna is not
connected or transmission is Try to disconnect the antenna then reconnect, or turn off the
not being received properly. power then turn back on.
Make sure that the antenna is securely connected.
The encryption code is being Wait until the encryption code has been updated.
updated.
NO SIGNL
LOADING
The signal is too weak.
Adjust the antenna so that the signal is as strong as possible.
Wait until the audio channel or information has been acquired.
The audio channel or
information is being
acquired.
OFF AIR
– – – –
The selected channel is off Make sure that you selected the channel properly.
the air.
Try to select another channel.
There is no characteristic
information such as an artist
name, song title or program
title available.
—
– –
The preset number entered is Enter a number from 1 to 30.
an invalid number.
XM –– – CH
The selected channel is not
available.
—
66US
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
• Some audio input modes may not be set up
depending on the input.
Other Operations
• When the ANALOG DIRECT function is being
used, the audio input mode is set to “ANALOG”
automatically. You cannot select other modes.
Switching between
digital and analog audio
(INPUT MODE)
When you connect components to both digital
and analog audio input jacks (SAT) on the
receiver, you can fix the audio input mode.
1 Turn INPUT SELECTOR on the
receiver to select the input.
You can also use the input buttons on the
remote.
2 Press INPUT MODE repeatedly
on the receiver to select the
audio input mode.
The selected audio input mode appears on
the display.
Audio input modes
• AUTO IN
Gives priority to digital audio signals when
there are both digital and analog
connections. If there are no digital audio
signals, analog audio signals are selected.
• HDMI IN
Specifies the digital audio signals input to
the HDMI jack.
• COAX IN
Specifies the digital audio signals input to
the DIGITAL COAXIAL jack.
• OPT IN
Specifies the digital audio signals input to
the DIGITAL OPTICAL jack.
• ANALOG
Specifies the analog audio signals input to
the AUDIO IN (L/R) jacks.
67US
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying the DIGITAL
MEDIA PORT
(DMPORT)
The DIGITAL MEDIA PORT (DMPORT)
allows you to enjoy sound from a network
system such as a portable audio source or
computer.
By connecting a DIGITAL MEDIA PORT
adapter (not supplied), you can enjoy sound
from the connected component on the
receiver.
For details, refer to the operating instructions
supplied with the DIGITAL MEDIA PORT
adapter.
Notes
• Do not connect an adapter other than the DIGITAL
MEDIA PORT adapter.
• Do not connect or disconnect the DIGITAL
MEDIA PORT adapter while the receiver is turned
on.
• Depending on the DIGITAL MEDIA PORT
adapter, video output may not be possible.
• The DIGITAL MEDIA PORT adapters are
available for purchase depending on the area.
68US
Download from Www.Somanuals.com. All Manuals Search And Download.
You can also view the images on the TV
screen by connecting the video output of the
DIGITAL MEDIA PORT adapter to the
receiver.
To view the images, proceed to “Watching a
Connecting the DIGITAL MEDIA
PORT adapter
You can listen to the sound from the
component connected through the DIGITAL
MEDIA PORT adapter to the DMPORT jack
on the receiver.
TV
DIGITAL
DVD IN
VIDEO 2/BD IN
(ASSIGNABLE)
OPTICAL
ANTENNA
SAT
IN
HDMI
AM
A
VIDEO
IN
1
XM
COAXIAL
DVD
IN
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN VIDEO OUT
DMPORT
DVD
MONITOR
L
L
L
DIGITAL MEDIA
PORT adapter
AUDIO OU
R
R
R
IN
IN
AUDIO IN
AUDIO OUT AUDIO IN
SUB
SA-CD/
CD
TV
SAT
VIDEO 1
WOOFE
A
To one of the
VIDEO IN jacks
VIDEO 3 IN/PORTABLE AV IN
VIDEO
L
AUDIO
R
Front panel
* The type of connector varies depending on the DIGITAL MEDIA PORT adapter.
For details, refer to the operating instructions supplied with the DIGITAL MEDIA PORT adapter.
AVideo cord (not supplied)
Notes
To detach the DIGITAL MEDIA
• When connecting the DIGITAL MEDIA PORT
adapter, be sure the connector is inserted with the
arrow mark facing towards the arrow mark on the
DMPORT jack.
• Be sure to make DMPORT connections firmly,
insert the connector straight in.
PORT adapter from DMPORT
jack
DMPORT
• As the connector of the DIGITAL MEDIA PORT
adapter is fragile, be sure to handle with care when
placing or moving the receiver.
2
1
Press and hold both sides of the connector and
then pull out the connector.
69US
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Press V/v repeatedly to select
the composite video input you
want to assign to DMPORT
input.
Listening to a connected
component through DMPORT
connection
Initial setting: –NONE
1 Press DMPORT.
The assignable composite video input are
VIDEO 1, VIDEO 3, DVD and SAT
inputs.
You can also use the INPUT SELECTOR
on the receiver to select “DMPORT”.
2 Start playback of the connected
For example, select “–VIDEO 1”.
When you press DMPORT, the images
from the component connected to the
VIDEO 1 VIDEO IN jack through
DIGITAL MEDIA PORT adapter will
appear on the TV screen.
component.
The sound is played back on the receiver.
For details, refer to the operating
instructions supplied with the DIGITAL
MEDIA PORT adapter.
Watching a connected
component through DMPORT
connection
To return to the previous
display
Press B.
Notes
You need to assign a composite video input to
DMPORT input so that you can view the
images on the TV screen.
• Depending on the type of DIGITAL MEDIA
PORT adapter, you can operate the connected
component by using the remote. For details on the
• Be sure you have made the video connection from
DIGITAL MEDIA PORT adapter to the receiver
1 Press AMP MENU.
“1-LEVEL” appears on the display.
2 Press V/v repeatedly to select
• Be sure you have connected the MONITOR OUT
• Depending on the DIGITAL MEDIA PORT
adapter, video output may not be possible.
“6-VIDEO”.
3 Press
or b to enter the
menu.
Tip
When listening to MP3 or other compressed music
using a portable audio source, you can enhance the
sound. Press MUSIC repeatedly to select
4 Press V/v repeatedly to select
“DMPORT V.”.
5 Press
or b to enter the
parameter.
70US
Download from Www.Somanuals.com. All Manuals Search And Download.
8 Press V/v repeatedly to select
the input (“DVD” in the
Listening to digital sound
from other inputs
(DIGITAL ASSIGN)
example) you want to assign to
the digital audio input jack
When “DVD” input is selected, the sound
of the DVD player will become a digital
sound through the OPTICAL VIDEO 1
IN jack.
The input you can assign varies for each
audio input. For details, see the following
You can reassign digital audio input that has
OPTICAL or COAXIAL (SAT IN, VIDEO 1
IN, DVD IN) signals to another input when
they are not currently being used.
For example, to output the sound source for
the DVD player using the OPTICAL IN jack
on the receiver:
• Connect the optical output jack of the DVD
player to the OPTICAL VIDEO 1 IN jack of
the receiver.
• Assign “VD1” to “DVD” in the “D.
ASSIGN” setting.
Assignable inputs for digital
audio input
The initial setting is marked with an
underscore.
1 Press AMP MENU.
Digital audio Assignable
Display
input
inputs
VIDEO 1
VIDEO 2
VIDEO 3
DVD
“1-LEVEL” appears on the display.
VIDEO 1
OPTICAL
VD1– VD1
VD1– VD2
VD1– VD3
VD1– DVD
VD1– TV
2 Press V/v repeatedly to select
“5-AUDIO”.
3 Press
or b to enter the
TV
menu.
SA-CD/CD
VIDEO 1
VIDEO 2
VIDEO 3
DVD
VD1– CD
4 Press V/v repeatedly to select
DVD
COAXIAL
DVD– VD1
DVD– VD2
DVD– VD3
DVD– DVD
DVD– SAT
DVD– TV
DVD– CD
SAT– VD2
SAT– VD3
SAT– DVD
SAT– SAT
SAT– TV
“D. ASSIGN”.
5 Press
or b to enter the
parameter.
SAT
6 Press V/v repeatedly to select a
vacant digital audio input
(“VD1” in the example).
TV
SA-CD/CD
VIDEO 2
VIDEO 3
DVD
SAT
OPTICAL
7 Press
or b to enter your
selection.
SAT
TV
SA-CD/CD
SAT– CD
continued
71US
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
• You cannot reassign more than one digital audio
input to the same input.
Naming inputs
You can enter a name of up to 8 characters for
inputs and display it on the receiver’s display.
This is convenient for labeling the jacks with
the names of the connected components.
• You cannot use the digital audio input as the
original input when it has been reassigned to
another input.
• When you assign the digital audio input, the
INPUT MODE setting may change automatically
1 Press the input button to select
the input you want to create an
index name for.
You can also use INPUT SELECTOR on
the receiver.
2 Press AMP MENU.
“1-LEVEL” appears on the display.
3 Press V/v repeatedly to select
“5-AUDIO” or “6-VIDEO”.
4 Press
or b to enter the
menu.
5 Press V/v to select “NAME IN”.
6 Press or b to enter the
parameter.
The cursor flashes and you can select a
character. Follow the procedure given in
72US
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the display
Using the Sleep Timer
You can check the sound field, etc., by
changing the information on the display.
Be sure to use the buttons on the receiver for
this operation.
You can set the receiver to turn off
automatically at a specified time.
Press SLEEP repeatedly while the
power is on.
Each time you press the button, the display
changes cyclically as follows:
Press DISPLAY repeatedly.
Each time you press the button, the display
changes cyclically as follows.
2-00-00 t 1-30-00 t 1-00-00 t 0-30-00
t OFF
All inputs except the FM and AM
band and XM Radio
When sleep timer is activated, the display
dims.
a)
Index name of the input t Selected input
t Sound field currently applied
Note
If you press any buttons on the remote or receiver
after the display dims, the display brightens up.
After a while, the display dims again if no button is
pressed.
FM and AM band
a)
Preset station name t Frequency t Sound
field currently applied
Tip
To check the remaining time before the receiver
turns off, press SLEEP. The remaining time appears
on the display. If you press SLEEP again, the sleep
timer will be canceled.
XM Radio
Channel name t Channel number t
Category name t Artist name/Feature t
Song/program title t Sound field currently
applied
a)
Index name appears only when you have assigned
Index name does not appear when only blank
spaces have been entered, or it is the same as the
input name.
Note
Character or marks may not be displayed for some
languages.
73US
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording using the
receiver
Using the Remote
Changing button
assignments
You can change the factory settings of the
input buttons to suit the components in your
system. For example, if you connect a DVD
recorder to the VIDEO 1 jacks on the receiver,
you can set the VIDEO 1 button on this remote
to control the DVD recorder.
Recording onto a recording
media
You can record from a video component using
the receiver. See the operating instructions
supplied with your recording component.
1 Press one of the input buttons
to select the playback
component.
1 Hold down the input button of
which you want to change the
assignment.
You can also use INPUT SELECTOR on
the receiver.
Example: Hold down VIDEO 1.
2 Prepare the playback
component for playing.
2 Referring to the table below,
press the corresponding
button for the category you
want.
For example, insert the video tape you
want to copy into the VCR.
3 Prepare the recording
Example: Press 4.
Now you can use the VIDEO 1 button to
control the DVD recorder.
component.
Insert a blank video tape, etc. into the
recording component (VIDEO 1) for
recording.
4 Start recording on the
recording component, then
start playback on the playback
component.
Notes
• Some sources contain copy guards to prevent
recording. In this case, you may not be able to
record from the source.
• When DMPORT input is selected and you have
assigned VIDEO 1 input to DMPORT input, no
video signals are output from the VIDEO 1 VIDEO
OUT jack.
74US
Download from Www.Somanuals.com. All Manuals Search And Download.
Categories and the
corresponding buttons
Additional Information
Categories
Press
a)
VCR (command mode VTR 3)
1
2
3
Glossary
a)
VCR (command mode VTR 2)
x Component video
DVD player/DVD recorder
A format for transmitting video signal
information consisting of three separate
signals: luminance Y, chrominance Pb, and
chrominance Pr. High quality pictures, such as
DVD video or HDTV pictures, are transmitted
more faithfully. The three jacks are color -
coded green, blue and red.
b)
(command mode DVD1)
DVD recorder
(command mode DVD3)
4
b)
CD player
5
6
7
8
9
Euro Digital Satellite Receiver
DVR (Digital CATV terminal)
DSS (Digital Satellite Receiver)
Blu-ray disc player
x Composite video
A standard format for transmitting video
signal information. The luminance signal Y
and chrominance signal C are combined and
transmitted together.
c)
(command mode BD1)
Blu-ray disc recorder
(command mode BD3)
0/10
-/--
c)
x Dolby Digital
TV
Digital audio encoding/decoding technology
developed by Dolby Laboratories, Inc. It
consists of front (left/right), center, surround
(left/right) and sub woofer channels. It is a
designated audio standard for DVD-video and
also known as 5.1 channel surround. Since
surround information is recorded and
reproduced in stereo, more realistic sound with
fuller presence is delivered than with Dolby
surround.
Not assigned
ENTER/
MEMORY
a)
Sony VCRs are operated with a VTR 2 or VTR 3
setting which corresponds to 8 mm and VHS
respectively.
Sony DVD recorders are operated with a DVD1 or
DVD3 setting. For details, refer to the operating
instructions supplied with the DVD recorders.
For details on the BD1 or BD3 setting, refer to the
operating instructions supplied with the blu-ray
disc player or blu-ray disc recorder.
b)
c)
x Dolby Digital Surround EX
Acoustic technology developed by Dolby
Laboratories, Inc. Surround back information
is matrixed into regular left and right surround
channels so that the sound can be reproduced
in 6.1 channel. Active scenes, especially, are
recreated with a more dynamic and realistic
sound field.
To clear all remote button
assignments
Press ?/1, DMPORT and MASTER VOL – at
the same time.
The remote is reset to its factory settings.
continued
75US
Download from Www.Somanuals.com. All Manuals Search And Download.
x Dolby Pro Logic II
x DTS-ES
This technology converts 2 channel stereo
recorded audio into 5.1 channel for playback.
There is a MOVIE mode for movies and
MUSIC mode for stereo sources such as
music. Old movies encoded in the traditional
stereo format can be enhanced with 5.1
channel surround sound.
Format for 6.1 channel playback with
surround back information. There are two
modes, “Discrete 6.1” which records all
channels independently, and “Matrix 6.1”
which matrixes surround back channel into LS
(left surround) and RS (right surround)
channels. It is ideal for playback of motion
picture soundtracks.
x Dolby Pro Logic IIx
Technology for 7.1 channel (or 6.1 channel)
playback. Along with audio encoded in Dolby
Digital Surround EX, 5.1 channel Dolby
Digital encoded audio can be reproduced in
7.1 channel (or 6.1 channel). Furthermore,
existing stereo recorded content can also be
reproduced in 7.1 channel (or 6.1 channel).
x DTS Neo:6
This technology converts 2 channel stereo
recorded audio for 6.1 channel playback.
There are two modes to select according to the
playback source or your preference, CINEMA
for movies, and MUSIC for stereo sources
such as music.
x Dolby Surround (Dolby Pro
Logic)
x HDMI (High-Definition
Multimedia Interface)
Audio processing technology developed by
Dolby Laboratories, Inc. Center and mono
surround information is matrixed into two
stereo channels. When reproduced, audio is
decoded and output in 4 channel surround
sound. This is the most common audio
processing method for DVD-video.
HDMI is an interface that supports both video
and audio on a single digital connection. The
HDMI connection carries standard to high
definition video signals and multi-channel
audio signals to audio/video components, such
as HDMI equipped TVs, in digital form
without degradation. The HDMI specification
supports HDCP (High-bandwidth Digital
Contents Protection), a copy protection
technology that incorporates coding
x DTS 96/24
A high sound quality digital signal format. It
records audio at a sampling frequency and bit
rate of 96kHz/24bit which is the highest
possible for DVD-video. The number of
playback channels varies depending on the
software.
technology for digital video signals.
x Sampling frequency
To convert analog audio to digital, analog data
should be quantified. This process is called
sampling, and the number of times per second
the analog data is quantified is called the
sampling frequency. A standard music CD
stores data quantified at 44,100 times per
second, which is expressed as a sampling
frequency of 44.1 kHz. Generally speaking, a
higher sampling frequency means better sound
quality.
x DTS Digital Surround
Digital audio encoding/decoding technology
for theaters developed by DTS, Inc. It
compresses audio less than Dolby Digital,
delivering a higher quality sound
reproduction.
76US
Download from Www.Somanuals.com. All Manuals Search And Download.
On placement
• Place the receiver in a location with adequate
ventilation to prevent heat buildup and
prolong the life of the receiver.
• Do not place the receiver near heat sources,
or in a place subject to direct sunlight,
excessive dust, or mechanical shock.
• Do not place anything on top of the cabinet
that might block the ventilation holes and
cause malfunctions.
Precautions
On safety
Should any solid object or liquid fall into the
cabinet, unplug the receiver and have it
checked by qualified personnel before
operating it any further.
• Do not place the receiver near equipment
such as a television, VCR, or tape deck. If
the receiver is being used in combination
with a television, VCR, or tape deck, and is
placed too close to that equipment, noise
may result, and picture quality may suffer.
This is especially likely when using an
indoor antenna (aerial). Therefore, we
recommend using an outdoor antenna
(aerial).
On power sources
• Before operating the receiver, check that the
operating voltage is identical with your local
power supply.
The operating voltage is indicated on the
nameplate on the back of the receiver.
• The unit is not disconnected from the AC
power source (mains) as long as it is
connected to the wall outlet, even if the unit
itself has been turned off.
• If you are not going to use the receiver for a
long time, be sure to disconnect the receiver
from the wall outlet. To disconnect the AC
power cord (mains lead), grasp the plug
itself; never pull the cord.
• Use caution when placing the receiver on
surfaces that have been specially treated
(with wax, oil, polish, etc.) as staining or
discoloration of the surface may result.
• One blade of the plug is wider than the other
for the purpose of safety and will fit into the
wall outlet only one way. If you are unable to
insert the plug fully into the outlet, contact
your dealer.
On operation
Before connecting other components, be sure
to turn off and unplug the receiver.
On cleaning
• The AC power cord (mains lead) must be
changed only at a qualified service shop.
Clean the cabinet, panel, and controls with a
soft cloth slightly moistened with a mild
detergent solution. Do not use any type of
abrasive pad, scouring powder, or solvent,
such as alcohol or benzine.
On heat buildup
Although the receiver heats up during
operation, this is not a malfunction. If you
continuously use this receiver at a large
volume, the cabinet temperature of the top,
side and bottom rises considerably. To avoid
burning yourself, do not touch the cabinet.
If you have any questions or problems
concerning your receiver, please consult your
nearest Sony dealer.
77US
Download from Www.Somanuals.com. All Manuals Search And Download.
There is no sound from one of the front
speakers.
Troubleshooting
If you experience any of the following
difficulties while using the receiver, use this
troubleshooting guide to help you remedy the
problem.
• Connect a pair of headphones to the
PHONES jack to verify that sound is
output from the headphones. If only one
channel is output from the headphones, the
component may not be connected to the
receiver correctly. Check that all the cords
are fully inserted into the jacks on both the
receiver and the component. If both
channels are output from the headphones,
the front speaker may not be connected to
the receiver correctly. Check the
Audio
There is no sound, no matter which
component is selected, or only a very
low-level sound is heard.
connection of the front speaker which is
not outputting any sound.
• Check that the speakers and components
are connected securely.
• Make sure you have connected to both the
L and R jacks of an analog component, and
not only to either the L or R jack. Use an
audio cord (not supplied).
• Check that both the receiver and all
components are turned on.
• Check that MASTER VOLUME is not set
to “VOL MIN”.
• Check that the SPEAKERS (OFF/A/B) is
not set to “OFF”.
• Check that headphones are not connected.
• Press MUTING to cancel the muting
function.
• Check that you have selected the correct
component with the input buttons.
• The protective device on the receiver has
been activated. Turn off the receiver,
eliminate the short-circuit problem, and
turn on the power again.
There is no sound from analog 2
channel sources.
• Check that the INPUT MODE is not set to
“COAX IN” or “OPT IN” for the selected
input (page 67).
There is no sound from digital sources
(from COAXIAL or OPTICAL input jack).
• Check that the INPUT MODE is not set to
“ANALOG”. Check that the INPUT
MODE is not set to “COAX IN” for the
sources from the OPTICAL input jack, or
to “OPT IN” for the sources from the
• Check that ANALOG DIRECT is not set
to on.
There is no sound from a specific
component.
• Check that the component is connected
correctly to the audio input jacks for that
component.
• Check that the cord(s) used for the
connection is (are) fully inserted into the
jacks on both the receiver and the
component.
78US
Download from Www.Somanuals.com. All Manuals Search And Download.
The source sound input from the HDMI
jack is not output from the receiver or
the TV speaker.
• Check the HDMI connection.
• You cannot listen to the Super Audio CD
by connecting HDMI.
• Depending on the playback component,
you may need to set up the component.
Refer to the operating instructions
supplied with each component.
There is no sound from the surround
back speaker.
• Some discs have no Dolby Digital
Surround EX flag even though the
packages have Dolby Digital Surround EX
logos. In this case, select “SB ON” (page
37).
There is no sound from the sub woofer.
• Check that the sub woofer is connected
correctly and securely.
• Make sure you have turned on your sub
woofer.
The left and right sounds are
unbalanced or reversed.
• Check that the speakers and components
are connected correctly and securely.
• Adjust the balance parameters using the
LEVEL menu.
• Make sure the sub woofer is set to “YES”
• There is no sound from the sub woofer
depending on the sound field.
There is severe hum or noise.
• Check that the speakers and components
are connected securely.
• Check that the connecting cords are away
from a transformer or motor, and at least
10 feet away from a TV set or fluorescent
light.
The surround effect cannot be
obtained.
• Make sure the sound field function is on
(press MOVIE, or MUSIC).
• Sound fields do not function for signals
with a sampling frequency of more than
48 kHz.
• Move your audio components away from
the TV.
• The plugs and jacks are dirty. Wipe them
with a cloth slightly moistened with
alcohol.
Dolby Digital or DTS multi channel
sound is not reproduced.
• Check that the DVD, etc. you are playing
is recorded in Dolby Digital or DTS
format.
There is no sound, or only a very low-
level sound is heard from the center/
surround/surround back speakers.
• Select a CINEMA STUDIO EX mode
• When connecting the DVD player, etc., to
the digital input jacks of this receiver,
check the audio setting (the settings for the
audio output) of the connected component.
• Make sure the center/surround speakers
are set to either “SMALL” or “LARGE”
• Make sure the surround back speaker is set
to “YES” (page 39).
continued
79US
Download from Www.Somanuals.com. All Manuals Search And Download.
Video
Tuner
There is no picture or an unclear
picture appears on the TV screen.
• Select the appropriate input using the input
buttons.
• Set your TV to the appropriate input mode.
• Move your audio components away from
the TV.
• Assign the composite video input to the
DMPORT input correctly.
The FM reception is poor.
• Use a 75-ohm coaxial cable (not supplied)
to connect the receiver to an outdoor FM
antenna (aerial) as shown below. If you
connect the receiver to an outdoor antenna
(aerial), ground it against lightning. To
prevent a gas explosion, do not connect the
ground wire to a gas pipe.
Outdoor FM antenna (aerial)
• Depending on the DIGITAL MEDIA
PORT adapter, video output may not be
possible.
Receiver
ANTENNA
The source image input to the HDMI
jack on the receiver is not output from
the TV.
AM
Ground wire
(not supplied)
• Check the HDMI connection.
• Depending on the playback component,
you may need to set up the component.
Refer to the operating instructions
supplied with each component.
To ground
Recording cannot be carried out.
• Check that the components are connected
correctly.
• Select the source component using the
input buttons.
Radio stations cannot be tuned in.
• Check that the antennas (aerials) are
connected securely. Adjust the antennas
(aerials) and connect an external antenna
(aerial), if necessary.
• The signal strength of the stations is too
weak (when tuning in with automatic
tuning). Use direct tuning.
• Make sure you set the tuning interval
correctly (when tuning in AM stations
with direct tuning).
• No stations have been preset or the preset
stations have been cleared (when tuning by
scanning preset stations). Preset the
• Press DISPLAY repeatedly on the receiver
so that the frequency appears on the
display.
80US
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote commander
If you are unable to remedy the
problem using the
The remote does not function.
• Point the remote at the remote sensor on
the receiver.
• Remove any obstacles in the path between
the remote and the receiver.
troubleshooting guide
Clearing the receiver’s memory may remedy
memorized settings will be reset to their
factory settings and you will have to readjust
all settings on the receiver.
• Replace all the batteries in the remote with
new ones, if they are weak.
• Make sure you select the correct input on
the remote.
If the problem persist
Consult your nearest Sony dealer. Note that if
service personnel changes some parts during
repair, these parts may be retained.
Error messages
Reference sections for clearing
the receiver’s memory
If there is a malfunction, the display shows a
message. You can check the condition of the
system by the message. Refer to the following
table to solve the problem. If any problem
persists, consult your nearest Sony dealer.
If an error message appears while you perform
Auto Calibration, see “Error and warning
codes” (page 30) to solve the problem.
To clear
See
All memorized settings
Customized sound fields
DEC. EROR
Appears when a signal the receiver cannot
decode (ex. DTS-CD) is input and “DEC.
PRI.” on the AUDIO menu is set to “DEC.
PCM”. Set it to “DEC. AUTO” (page 38).
PROTECT
Irregular current is output from the
speakers. The receiver will automatically
turn off after a few seconds. Check the
speaker connection and turn on the power
again.
81US
Download from Www.Somanuals.com. All Manuals Search And Download.
Inputs
Analog
Sensitivity: 500 mV/
50 kohms
Specifications
3)
S/N : 96 dB
4)
(A, 500 mV )
AUDIO POWER
SPECIFICATIONS
Digital (Coaxial) Impedance: 75 ohms
S/N: 100 dB
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
(A, 20 kHz LPF)
Digital (Optical) S/N: 100 dB
(A, 20 kHz LPF)
(Models of area code U only)
With 8 ohm loads, both channels driven, from
20 – 20,000 Hz; rated 95 watts per channel
minimum RMS power, with no more than
0.09% total harmonic distortion from 250
milliwatts to rated output.
Outputs (Analog)
AUDIO OUT
Voltage: 500 mV/10
kohms
SUB WOOFER Voltage: 2 V/1 kohm
Equalizer
Gain levels
6 dB, 1 dB step
Amplifier section
Models of area code U, CA
1)
3)
4)
INPUT SHORT (with sound field and equalizer
bypassed).
Weighted network, input level.
Minimum RMS Output Power (8 ohms, 20 Hz –
20 kHz, THD 0.09%)
95 W + 95 W
Stereo Mode Output Power (8 ohms, 1 kHz,
THD 1%)
FM tuner section
Tuning range
87.5 - 108.0 MHz
FM wire antenna
105 W + 105 W
Antenna
2)
Surround Mode Output Power (8 ohms, 1 kHz,
Antenna terminals 75 ohms, unbalanced
Intermediate frequency
10.7 MHz
THD 10%)
140 W/ch
1)
Measured under the following conditions:
AM tuner section
Tuning range
Area code
Power requirements
Area code
Tuning scale
U, CA
120 V AC, 60 Hz
10 kHz step 9 kHz step
2)
Reference power output for front, center, surround
and surround back speakers. Depending on the
sound field settings and the source, there may be
no sound output.
U, CA
530 –
1,710 kHz
531 –
1,710 kHz
5)
5)
Antenna
Loop antenna
Intermediate frequency
450 kHz
Frequency response
Analog
10 Hz – 70 kHz
+0.5/–2 dB (with sound
field and equalizer
bypassed)
5)
You can change the AM tuning scale to 9 kHz or
10 kHz. After tuning in any AM station, turn off
the receiver. While holding down TUNING
MODE, press ?/1. All preset stations will be
erased when you change the tuning scale. To reset
the scale to 10 kHz (or 9 kHz), repeat the
procedure.
82US
Download from Www.Somanuals.com. All Manuals Search And Download.
Video section
Inputs/Outputs
Video:
1 Vp-p/75 ohms
COMPONENT VIDEO:
Y: 1 Vp-p/75 ohms
PB/CB: 0.7 Vp-p/75 ohms
PR/CR: 0.7 Vp-p/75 ohms
80 MHz HD Pass Through
General
Power requirements
Area code
Power requirements
U, CA
120 V AC, 60 Hz
Power output (DIGITAL MEDIA PORT)
DC OUT
5 V, 700 mA
Power consumption
Area code
Power consumption
250 W
U
CA
340 VA
Power consumption (during standby mode)
0.3 W (when
“CONTROL” in VIDEO
menu is set to “CTRL
OFF”)
Dimensions (w/h/d) (Approx.)
430 × 157.5 × 310 mm
(16 7/8 × 6 2/8 × 12 2/8
inches) including
projecting parts and
controls
Mass (Approx.)
7.8 kg (17 lb 4 oz)
Supplied accessories
FM wire antenna (aerial) (1)
AM loop antenna (aerial) (1)
Remote commander RM-AAU014 (1)
R6 (size-AA) batteries (2)
Optimizer microphone (ECM-AC2 or
ECM-AC2a) (1)
For details on the area code of the
Design and specifications are subject to
change without notice.
83US
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Numerics
E
S
Satellite tuner
Selecting
H
HDMI
A
AUTO FORMAT DIRECT
(A.F.D.) 49
I
Set-top box
Sound fields
Speakers
Super Audio CD player
B
M
Menu
Blu-ray disc player
C
Camcorder
CD player
T
Tuner
Tuning
TV
D
N
Digital Cinema Sound
(DCS) 53
DIGITAL MEDIA PORT
R
Recording onto a recording
media 74
V
VCR
DVD player
Video game
DVD recorder
X
(2)
Sony Corporation Printed in Malaysia
Download from Www.Somanuals.com. All Manuals Search And Download.
|