High Resolution Day & Night IR Camera SIR-4160 User Guide
Before installing and operating this product,
please read this manual thoroughly.
ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
Before operating the camera, confirm the camera model and correct input power
voltage. In order to that you can understand this manual thoroughly, we will explain the
model description.
n SIR-4160 SERIES
• NTSC MODEL
SIR-4160N
• PAL MODEL
SIR-4160P
n MODEL DESCRIPTION
• SIR-4160 X
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
_
SIGNAL SYSTEM
• SIGNAL SYSTEM
N --> NTSC MODEL
P --> PAL MODEL
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
INFORMATION -This equipment has been tested and found to comply with limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
WARNING -Changes or modifications not expressly approved by the manufacturer
could void the user’s authority to operate the equipment.
WARNING -To prevent electric shock and risk of fire hazards:
◆ Do NOT use power sources other than that specified.
◆ Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Features
• Features ……………………………………………………………… 5
• Warnings & cautions………………………………………………… 6
• Precautions…………………………………………………………… 7
• Components and Accessories ……………………………………… 9
• Overview …………………………………………………………… 9
Ultra High Sensitivity
Outdoor Visibility range 50M
The built-in high sensitivity COLOR CCD produces a
clear image even in 0Lux(B/W, IR-LED ON)or lower
illumination.
The IR LEDs of the SIR-4160 automatically illuminates
viewing area in the extreme darkness allowing the
camera a long-range visibility of up to 50 meters.
IR MODE Function
High Resolution
n
Front……………………………………………………………………………… 9…
This function prevents the saturation of the image by
the IR illuminators at short distance.
n
…
Back……………………………………………………………………………… 10
By adopting a diagonal 6mm(1/3") 410,000 (NTSC)
pixel, 470,000(PAL) pixel SONY CCD, the camera
produces clear picture quality with a horizontal
resolution of 600 TV lines for color and a horizontal
resolution of 700TV lines for BW mode.
• Adjust to lens………………………………………………………… 11
IP66 Approved/Dust and Rain
Resistant
n
Ajust to Lens’s ZOOM and Focus………………………………………………… 11
With dust and rain resistant design, the camera can be
installed outside under building eaves or places that
are exposed to the dust and rain.
• Connection…………………………………………………………… 12
SSNR3 (Samsung Super Noise
Reduction) Function
n
n
n
n
Connecting to a monitor………………………………………………………… 12…
Connecting to power… ………………………………………………………… 13…
RS-485 Communication control………………………………………………… 14
Using Coaxial Communications………………………………………………… 15
…
…
…
Communication
The high-performance W-V DSP chip effectively
removes low-light gain noise and ghosting to provide
clear images even in dark environments.
RS-485, Coaxial communication methods are
supported.
-RS-485 Communications
: STW(SPD), PELCO-P, PELCO-D, VICON, PANASONIC,
BOSCH, HONEYWELL, SEC
-Coaxial Communications
: Pelco Coaxitron
• Operating Your Camera …………………………………………… 16
n
n
Menu Configuration……………………………………………………………… 16…
Menu Setup……………………………………………………………………… 16…
• LENS (Adjusting to the brightness level)…………………………………… 17…
…
DAY&NIGHT(ICR)
This camera has a function that automatically selects
the mode that is appropriate for daytime or night-time
conditions.
The COLOR mode operates in daytime conditions to
provide optimum colors, and BW mode operates in
night-time conditions to enhance the definition of the
image.
… … • EXPOSURE… …………………………………………………………… 18…
… … • White Balance (White Bal.)………………………………………………… 19
… … • SSDR (Samsung Super Dynamic Range)…………………………………… 20
…
…
Miscellaneous Functions
… … • BACKLIGHT……………………………………………………………… 21…
… … • SSNR3…………………………………………………………………… 23…
… … • DAY/NIGHT… …………………………………………………………… 24…
… … • SPECIAL… ……………………………………………………………… 26…
… … • EXIT……………………………………………………………………… 31
HLC(High Light Compensation), SENS-UP, FLIP(H/V-REV),
D-ZOOM, SHARPNESS, MOTION DETECTION and
PRIVACY functions are provided.
SSDR
OSD
(Samsung Super Dynamic Range)
• Troubleshooting……………………………………………………… 32
• Specifications………………………………………………………… 33
• Dimension …………………………………………………………… 34
The camera’s OSD is complimented by 18 languages.
- NTSC : Korean, English, French, Spanish, Japanese,
Portuguese, Taiwanese
- PAL : English, French, German, Spanish, Italian,
Chinese, Russian, Czech, Polish, Romanian,
Serbian, Swedish, Danish, Turkish, Portuguese
For images with high contrast between bright and dark
Areas from difficult lighting conditions such as
backlighting, this camera selectively illuminates darker
Areas while retaining the same light level for brighter
Areas to even out the overall brightness.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Samsung Techwin cares for the environment at all product manufacturing stages to preserve
the environment, and is taking a number of steps to provide customers with more
environment-friendly products. The Eco mark represents Samsung Techwin's will to create
environment-friendly products, and indicates that the product satisfies the EU RoHS Directive.
Precautions
Do not install under extreme
temperature conditions.
Do not install in high humidity
environment.
Warnings & Cautions
This information is provided to ensure your safety and to prevent any losses, financial or
otherwise. Please read it carefully and use the product accordingly.
* For product inquiries, please contact the retail shop where you bought the camera. The use of
equipment such as an aerial ladder while providing after-sales service shall be at your expense.
Notes
Use only under temperature conditions
between -10°C and +50°C. Provide
good ventilation when using in high
temperature conditions.
May lower image quality.
• Please make sure the product is installed appropriate places where secured from
flood, such as under the eaves, to operate properly.
• This product is certified as IP66 standard. However, if there is any flood concerns, it is
highly recommended to use an outdoor Housing When you install the camera inside
an outdoor Housing, please use one of the following methods:
1. Remove the front glass of Housing before installing the camera.
2. To keep the front glass of Housing, remove the front cover, and then put the camera
close to the front glass.
Warning/Attention/Special Mark Messages
Do not install under unstable
lighting conditions.
Avoid touching the camera lens.
Ignoring this information may result in
material loss or personal injuries.
Ignoring this information may result in
death or or serious personal injuries.
Indicates "No Disassembling."
Indicates "Never Allowed."
Severe lighting changes or flickering may
hinder normal camera operation.
The lens is the most important component
of the camera. Be careful not to smear it
with fingerprints.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Components and Accessories
Precautions
❶
❻
2
3
❹
5
Do not drop the camera or
subject it to physical shock.
Never keep the camera face to
strong light directly.
➐
➑
9
❶
4
➐
2
3
SIR-4160
Sunshield Adaptor (1EA)
DC 12V/4A Adaptor
Sunshield
Tapping Screw (3EA)
Power Cable
L-type hexagon wrenches (3.0mm)
User’s Manual
Installation Video Output Cable
5
➑
❻
9
May cause a product malfunction.
May damage the CCD.
* The set for America does not include the adapter.
Overview
Do not expose the camera to
radioactivity.
FRONT
2
3
❶
4
Radioactivity exposure may damage the
CCD.
5
➐
6
❶
2
3
4
5
6
Camera Sunshield
S unshield adaptor : Fixing the sunshield onto the camera.
Notes
Focus lever : Set focus of lens by turn the focus lever.
Zoom lever : Set zoom magnification of lens by turn the zoom lever.
• Exposure to a spotlight or an object emitting strong light may cause smear or
blooming.
• Ensure that the power source complies with normal specifications before supplying
it to the camera.
Front cover
Function Setup Switch :
Display the menu on the screen and move the cursor to four directions to confirm
status or after changing a selected item.
• In case of IR LED has been lighted, do not lighten directly eye.
➐
Video Output Terminal to Monitor :
Used for monitoring of video output When camera installation.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjust to Lens
Overview
Notes
Adjust the lens's zoom and focus
• When you adjust to the ZOOM & FOCUS of the lens, Please remove the front cover
from the camera, by turning the cover counterclockwise.
• To adjust the zoom & focus loosen the individual levers before tightening them
again.
1. Remove the sunshield from the camera.
2. Remove the front cover from the camera by turning it counterclockwise.
3. Unlock the Zoom or Focus lever before adjusting the lens.
• To ensure the weatherproof integrity is maintained, ensure the front cover is
tightened correctly.
4.Adjust the zoom & focus by moving the lever counterclockwise for (NEAR & TELE)
and clockwise for (WIDE & FAR) position.
5.After adjustment, tighten the zoom or focus levers, taking care not to adjust the
zoom/focus position.
6. Please, close and tighten the front cover.
7. Replace the sunshield.
BACK
Front cover
ZOOM lever
➑
❿
Focus lever
9
Notes
❽
9
Power input terminal : Connect the power as specified for each model here.
Video output terminal : Video signals are output through this port. Connect
• If the front cover is cross threaded or not correctly tightened the camera housing
will not be weatherproof.
• When you combine the front cover, combine the triangle of front cover and triangle
of main body confront each other.
this port to the Video IN port of a monitor.
RS-485 control terminal :
❿
You can control SETUP MENU through this port by using external controllers like a
Remote controller that RS-485 Communication is supported. For details, see page 14.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
11
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection
Connecting to Monitor
Connecting to Power
Please connect the video output terminal located on the back of the camera to the
monitor.
The recommended adaptor specification for SIR-4160N/P is DC 12V/4A, AC 24V/2A
over.
Please check the standard power requirement before connecting the power.
( Recommend AC 24A/2A over adaptor for a long-distance.)
Monitor
CCD Camera
• The connection method varies depending on the type of monitor and accessories.
Please refer to the user's manual for each instrument.
• Please turn off the power when connecting.
When the resistance value of copper wire is at [20°C(68°F)]
2
2
2
2
• Please select Hi-Z on the 75Ω/Hi-Z switch for the intermediate video TV set and
select 75Ω for the Intermediate device as shown in the picture below.
Copper wire size(AWG)
Resistance value(Ω/m)
Voltage drop(V/m)
#24(0.22mm )
#22(0.33mm )
#20(0.52mm )
#18(0.83mm )
0.078
0.028
0.050
0.018
0.030
0.011
0.018
0.006
• As shown in the table above, voltage decreases as the wire gets longer.
Therefore having an excessively long distance between the power adaptor and the
camera may affect the camera's performance.
Intermediate
End monitor
✽ Standard voltage for camera operation : DC 12V±10% / AC 24V±10%
✽ There may be some deviation in voltage drop depending on the type of wire and the manufacturer.
CCD Camera
Notes
• Please use a power adaptor that meets the required standards.
• Please connect the power after installation.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
13
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection
Using Coaxial Communications
• Coaxial Communications System
• OSD Control method
RS-485 communication control
Connecting to RS-485 Control Cable
CAMERA
SET
DVR
MENU/ENTER
UP KEY
CONTROLLER
OSD KEY
CONTROL CABLE
WHITE (TRX+)
SPEC
RS-485+
RS-485-
UP
JOYSTICK UP
BLCAK (TRX-)
DOWN
LEFT
DOWN KEY
LEFT KEY
JOYSTICK DOWN
JOYSTICK LEFT
JOYSTICK RIGHT
RIGHT
RIGHT KEY
Using RS-485 communication will enable you to control the OSD menu from a SAMSUNG
TECHWIN System Controller or DVR.
DVR
(1) Connection to a PC.
Connect the camera to the PC via a RS-485 converter using RS-485 and a serial cable.
EX) SERIAL PORT OF THE PC(COM1) → SERIAL CABLE → RS-485 CONVERTER → RS-485
CONTROL CABLE
DVD
(2) Connection to a DVR or System Controller.
Connect the RS-485 cable to the connection ports of the DVR or System Controller.
485 Control Board Connection Port
(+) CONNECTION TERMINAL
RS-485 Control Port
WHITE (TRX+)
: BNC
---- : RS-485
•
•
(-) CONNECTION TERMINAL
BLACK (TRX-)
– Video Cable
The camera's video output port is connected to the monitor with a BNC coaxial cable,
shown below : If the distance between the camera and the monitor exceeds the
recommended maximum, please use an auxiliary video amp.
* RS-485 Communication establishment initial value
Camera ID
1
BAUD RATE
9600
UART MODE
8-NONE-1
RET PKT
ENABLE
Item
Initial value
Distance Recommended Cable Specification
300m
450m
600m
3C2V(RG-59/U)
5C2V(RG-6/U)
7C2V(RG-11/U)
Notes
•
When making a control system to control the camera, please use to the
protocol(STW(SPD), PELCO-P, PELCO-D, VICON, PANASONIC, BOSCH, HONEYELL, SEC).
• When you connecting to RS-485 CONTROL TERMINAL, please peel off the outer
skin inside the RS-485 CONTROL TERMINAL.
In case of SCC-101 connection, change communication mode to『8-E-1』at『Communication
configuration』menu. (For more information, refer to SCC-101 manual.)
Notes
• If the camera is controlled through coaxial communication, please use a video amp
intended for coaxial communications. Regular video amps do not transfer coaxial
signals.
•
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
15
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Your Camera
Menu Configuration
MAIN SETUP
1.LENS
2.EXPOSURE
Select the function using
the Function Setup switch.
Change the status using
the Function Setup switch.
DC
MAIN SETUP
3.WHITE BAL
4.SSDR
5.BACKLIGHT
6.SSNR3
7.DAY/NIGHT
8.SPECIAL
9.EXIT
ATW
OFF
OFF
ON
●
LENS
DC
●
●
… ●
●
…
●
………
AGC
BRIGHTNESS
SENS-UP
SHUTTER
RETURN
EXPOSURE
AUTO
●
ATW
●
MANUAL
…
●
●
…
● …
INDOOR
OUTDOOR
AWC→SET
WHITE BAL
…
SAVE
●
●
●
●
…
●
SSDR
OFF
ON
…
OFF
●
BLC
…
●
●
BACKLIGHT
SSNR3
HLC
2. Select a desired function using the Function Setup switch.
• Place the cursor over a desired item.
3. Set up a selected item by using the Function Setup switch.
…
OFF
●
ON
…
●
B/W
…
DAY/NIGHT
COLOR
AUTO
4.To finish the setting, select ‘EXIT’ and press the Function Setup switch.
●
●
●
… ●
…
●
SYNC
●
DIS
IMAGE ADJ.
MOTION DET
COMM ADJ
CAM TITLE
PRIVACY
Notes
… ●
●
SPECIAL
EXIT
• An item with the…
icon also has sub menus. To select a sub menu, select an item with
… ●
LANGUAGE
RETURN
the icon and press the Function Setup switch.
• An item with the - - - icon is unavailable due to function settings.
●
SAVE
…
●
NOT SAVE
…
●
RESET
Menu Setup
Use the Function Setup Switch whitin the camera.
LENS
Using this function, you can control the screen brightness.
1.When the SETUP menu screen is displayed, select‘LENS’by using the Function Setup
switch so that the arrow indicates‘LENS’.
2. DC :You can adjust the minimum shutter and maximum value of ESC shutter mode.
MAIN SETUP
1.LENS
DC
2.EXPOSURE
1. Press the Function Setup switch.
• Main setup menu is displayed on the monitor screen.
3.THE Lens mode has sub menu items as listed below.
- BRIGHTNESS :Adjusts the video brightness.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
17
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Your Camera
Notes
- FOCUS ADJ :To adjust the DC lens focus correctly, you must activate the Focus Settings
mode under each lens menu. Activate the Focus Settings mode, adjust
the lens focus, and then deactivate the settings mode.
• When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled.
AGC(AUTO GAIN CONTROL) :The higher the gain level, the brighter the screen - but
the higher the noise.
Notes
- OFF : Deactivates the AGC function.
- LOW :Allows automatic gain control from 5.3dB to 32dB.
- HIGH :Allows automatic gain control from 5.3dB to 37dB.
• If color rolling occurs when using a DC lens, set Shutter to Fixed (---).
SENS-UP :When it is night or dark, the camera automatically detects the light level
and maintains a clear picture if this mode is activated.
- OFF : Deactivates the SENS-UP function.
EXPOSURE
MAIN SETUP
- AUTO :Activates the SENS-UP function.
1.LENS
2.EXPOSURE
3.WHITE BAL
DC
RETURN : Select this to save the changes in the EXPOSURE menu and return to the
SETUP menu.
ATW
Notes
1.When the SETUP menu screen is displayed, select 'EXPOSURE' by using the Function
Setup Switch.
2. Select a desired mode using the Function Setup switch.
• If you press the Function Setup switch to ‘AUTO’ mode, you can adjust brightness by increasing or
decreasing the shutter speed. (x2 ~ x512)
• Note that the higher the zoom level, the brighter the screen, but the more likely there will be a
ghosting effect.
• It is normal for Noise, Spots and Whitish symptoms to appear in SENS-UP mode when the
D-ZOOM level is increased.
EXPOSURE SETUP
1.BRIGHTNESS
2.SHUTTER
3.AGC
25
---
HIGH
OFF
4.SENS-UP
5.RETURN
White Balance (White Bal)
Use the White Balance function to adjust the screen color.
1.When the SETUP menu screen is displayed, select ‘White Bal’ by using the Function
Setup switch so that the arrow indicates ‘White Bal’.
2. Select a desired mode using the Function Setup switch.
SHUTTER :You can select either auto or manual shutter.
- ---
: Shutter speed is fixed at 1/60sec(1/50sec)
- ESC
: Select this to control the shutter speed automatically. If ESC is selected, the
shutter speed is automatically controlled depending on the ambient
illumination of the subject.
MAIN SETUP
1.LENS
DC
- MANUAL :You can control shutter speed manually.
2.EXPOSURE
(NTSC MODEL : 1/60~1/120,000, PAL MODEL : 1/50~1/120,000)
3.WHITE BAL
4.SSDR
ATW
OFF
- A.FLK
: Select this when you see picture flicker, this can happen when the frequency
of the local lighting clashes with the camera.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
19
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Your Camera
※ Select one of the following 5 modes, as appropriate for your purpose.
ATW
: Select this when the color temperature is between 1,700˚K and 11,000˚K.
OUTDOOR : Select this when the color temperature is between 1,700˚K and 11,000˚K.
(sodium light inclusion)
INDOOR
: Select this when the color temperature is between 4,500˚K and 8,500˚K.
MANUAL : Select this to fine-tune White Balance manually. Set White Balance first
by using the ATW or AWC mode. After that switch to MANUAL mode,
fine-tune the White Balance and then press the Function Setup switch.
AWC →SET :To find the optimal luminance level for the current environment, point
the camera towards a sheet of white paper and press the Function Setup
switch. If the environment changes, readjust it.
SSDR ON
SSDR OFF
BACKLIGHT
Notes
Unlike conventional cameras, the SIR-4160 is designed to deliver a distinctive subject and
background at the same time, even when the subject is backlight, by using the features of
the proprietary W-V DSP chip.
1.When the SETUP menu screen is displayed, select ‘BACKLIGHT’ by using the Function
Setup switch so that the arrow indicates ‘BACKLIGHT’.
• White Balance may not work properly under the following conditions. In this case
select the AWC mode.
❶
……When the color temperature of the environment surrounding the subject is out
of the control range (e.g. clear sky or sunset).
2
3
…When the ambient illumination of the subject is dim.
……If the camera is directed towards a fluorescent light or is installed in a place
where illumination changes dramatically, the White Balance operation may
become unstable.
MAIN SETUP
1.LENS
DC
2.EXPOSURE
SSDR (Samsung Super Dynamic Range)
3.WHITE BAL
4.SSDR
5.BACKLIGHT
6.SSNR3
ATW
OFF
OFF
ON
SSDR illuminates darker spots of an image while retaining the same light level for brighter
spots to even out the overall brightness of images with high contrast between bright and
dark spots.
MAIN SETUP
2. Select a desired mode using the Function Setup switch.
BLC : Enables a user to directly select a desired area from a picture, and to view the
area more clearly.
1.LENS
2.EXPOSURE
3.WHITE BAL
4.SSDR
5.BACKLIGHT
DC
ATW
OFF
OFF
HLC (High Light Compensation) :
If the scene contains extremely bright light areas such as; from car headlights, the
light can mask out much of the on-screen detail.
- LEVEL :Adjust level of the HLC function.
- LIMIT : Enable to change the operating condition.
- MASK COLOR/TONE : Change the color / transparency of the masking area.
1. When the SETUP menu screen is displayed, select ‘SSDR’ by using the switch so that
the arrow indicates ‘SSDR’.
2. Use the switch to change the SSDR level according to the contrast between bright
and dark areas.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
21
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Your Camera
(Black, Red, Blue, Cyan, Magenta)
- TOP/BOTTOM/LEFT/RIGHT :Adjust the area to be enhanced
SSNR3
This function reduces the background noise in a low luminance environment.
1.When the SETUP menu screen is displayed, select ‘SSNR3’ by using the Function
Setup switch so that the arrow indicates ‘SSNR3’.
OFF : Not being used
3. Select a desired mode using the Function Setup switch and press the Function Setup switch.
Select ‘BLC’ to adjust the area to be
enhanced then adjust the level.
HLC : Enable the user to change the level,
limit, mask color/tone and area.
MAIN SETUP
1.LENS
DC
2.EXPOSURE
3.WHITE BAL
4.SSDR
5.BACKLIGHT
6.SSNR3
ATW
OFF
OFF
ON
LOW
7.DAY/NIGHT
AUTO
2. Select a desired mode using the Function Setup switch.
OFF: Deactivates SSNR3. Noise is not reduced.
ON :Activates SSNR3 so that noise is reduced.
Notes
3. Set the SSNR3 mode to ‘ON’ and press the Function Setup switch. Then you can
adjust the noise reduction level.
• Because there can be a difference in the effectiveness of HLC according to the amount of
light area in the screen, optimize the installation angle for the best HLC performance.
• When dark, the HLC is only activated when a bright light exceeding a specific size in
NIGHT ONLY mode.
• The HLC is not activated in day light or when bright light is not present at night in NIGHT
ONLY mode.
Notes
• BLC Function doesn't work in the B/W mode of the DAY/NIGHT menu.
• You cannot set the SSNR3 to ‘ON’ or ‘OFF’ when the AGC mode of the
EXPOSURE menu is ‘OFF’.
• When adjusting the noise reduction level in the SSNR3 mode, remember that
the higher the level set, the more the noise level will be reduced, as will the
brightness of the image.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
23
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Your Camera
- BURST MODE :You can turn on or off the burst signal on
B/W mode.
- DURATION :You can select brightness of illumination
about changing the day/night mode.
- DWELL TIME :You can select the duration time about
changing the day/night mode. …
DAY/NIGHT
AUTO SETUP
▶ 1.BURST MODE
2.COLOR→B/W
DURATION
DWELL TIME
3.B/W→COLOR
DURATION
ON
FAST
3SEC
You can display pictures in color or black and white.
1.When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using the Function
Setup switch so that the arrow indicates ‘DAY/NIGHT’ .
FAST
10SEC
DWELLTIME
4.RETURN
→3s, 5s, 7s, 10s, 15s, 20s, 30s, 40, 60s
MAIN SETUP
Color → B/W
2.5 lux
B/W → Color
5 lux
10 lux
1.LENS
2.EXPOSURE
3.WHITE BAL
4.SSDR
5.BACKLIGHT
6.SSNR3
DC
Fast
Slow
* The day/night switching point of the camera
can be adjusted.
ATW
OFF
OFF
ON
1 lux
Notes
7.DAY/NIGHT
AUTO
8.SPECIAL
•
When AGC in the EXPOSURE menu is 'OFF', '---' mode operates as like selecting 'COLOR' mode
and 'AUTO' mode can not be selected.
2. Select a desired mode using the Function Setup Switch according to the picture display
you want.
COLOR :The picture is always displayed in color.
B/W : The picture is always displayed in black and white.
B/W MODE SETUP
-
BURST MODE :You can turn on or off the burst signal on B/W
mode.
▶1.BURST MODE
2.IR MODE
ON
ON
HIGH
- IR MODE :When IR LED is turned on in B/W, the objects
can be clearly identified due to the function that
decreases screen saturation of objects within a
short distance.
3.IR LEVEL
4.RETURN
· TOP/BOTTOM/LEFT/RIGHT :Adjust the range according to the location of objects.
- IR LEVEL : Select LOW when objects appears within a short distance or select HIGH
when objects appears within a long distance on the screen.
AUTO :The mode is switched to ’Color‘ in a normal environment, but switches to ’B/
W‘ mode when ambient illumination is low.To set up the switching time for
AUTO mode, press the Function Setup switch.You can turn on or off the burst
signal on B/W mode.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
25
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Your Camera
IMAGE ADJ. :
SPECIAL
1) When the SETUP menu screen is displayed, select ‘IMAGE ADJ’ by using the Function
Setup switch so that the arrow indicates ’IMAGE ADJ‘.
2) Select a desired mode using the Function Setup switch.
1.When the SETUP menu screen is displayed, select ‘SPECIAL’ by using the Function Setup
switch so that the arrow indicates ‘SPECIAL’.
IMAGE SETUP
MAIN SETUP
1.V-REV
2.H-REV
OFF
OFF
1.LENS
2.EXPOSURE
DC
3.D-ZOOM
OFF
WHITE
ON
3.WHITE BAL
4.SSDR
5.BACKLIGHT
6.SSNR3
ATW
OFF
OFF
ON
4.FONT COLOR
5.SHARPNESS
6.MONITOR
7.RETURN
LCD
7.DAY/NIGHT
AUTO
8.SPECIAL
9.EXIT
SAVE
• V-REV :You can flip the picture vertically on the screen.
• H-REV :You can flip the picture horizontally on the screen.
• D-ZOOM :You can use a digital zoom of x1 ~ x16.
• FONT COLOR :You can change the OSD font color. (White,Yellow, Green, Red, Blue)
• SHARPNESS :As you increase this value, the picture outline becomes stronger and
clearer. Adjust this value appropriately depending on the sharpness of
the picture.
2. Select a desired mode using the Function Setup switch.
• MONITOR : Please change the settings value of video
appropriate to your monitor.
SPECIAL
1.IMAGE ADJ
- LCD : Please select this menu item when using a LCD
monitor.
- CRT : Please select this menu item when using a CRT
monitor.
- USER : Please use this menu item when using a monitor other than standard ones.You
can change the gamma, PED level, and color gain in the sub menus.
• RETURN : Select this to save the settings for the IMAGE ADJ menu and to return to
the SETUP menu.
2.CAM TITLE
3.SYNC
4.MOTION DET
5.PRIVACY
6.DIS
7.COMM ADJ
8.LANGUAGE
9.RETRUN
OFF
INT
OFF
OFF
OFF
ENGLISH
Notes
• When the V-REV or H-REV mode is enabled, the text on the screen does not flip.
• If you increase the SHARPNESS level too high, the picture may become distorted
or noise may appear.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
27
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Your Camera
CAM TITLE : If you enter a title, the title will appear on the monitor.
1) If the SPECIAL menu screen is displayed, use the Function Setup switch so that the
arrow indicates ‘CAM TITLE’.
SYNC : In areas where the supply is at 60Hz(NTSC),
50Hz(PAL), you can synchronize the output phase
of multiple cameras using the power
synchronization function (Line-Lock) without using
a synchronization signal generator.
- INT : Internal Synchronization Type
- L/L : Power Synchronization Type, Line-lock
• Press the Function Setup switch.
• You can select a desired phase from 0 to 359 when select 'phase'.
CAMERA TITLE SETUP
2) Set it to ‘ON’ by using the Function Setup switch.
3) Press the Function Setup switch.
4) Use the Function Setup switch to move to
a desired letter and select the letter by
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
- . 0 1 2 3 4 5 6 7 8 9
pressing the Function Setup switch.
← → C L R P O S E N D
Repeat this to enter multiple letters. You
can enter up to 15 letters.
5) Enter a title, move the cursor to ‘POS’ and
Notes
press the Function Setup switch. The
entered title appears on the screen. Select
• When using AC power at 60Hz(NTSC), 50Hz(PAL), frequency, you can use the L/L
type synchronization.
• When the power is DC 12V, the SYNC menu is fixed to the ‘INT’ mode.
FRONT DOOR
the position to display the title on the
screen by using the Function Setup switch
and press the Function Setup switch.
When the position is determined, select
‘END’ and press the Function Setup switch
to return to the SPECIAL menu.
:
MOTION DET
This product has a feature that allows you to observe
movement of objects in 8 different areas on the screen,
and the words 'MOTION DETECTED' appear on the screen
when movement is detected.
Activity can be monitor more efficiently.
1) When the SPECIAL menu screen is displayed, press the
Function Setup switch so that the arrow indicates‘MOTION DET’.
2) Set up the mode using the Function Setup switch.
- SENSITIVITY : You can select up to 8 MD areas.When SENSITIVITY number is high, motion
detection sensitivity is increased to recognize even small movement.
Notes
• When the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen
even if you enter one.
• Only English is available in this mode.
• If you move the cursor to CLR and press the Function Setup switch, all the letters
are deleted. To edit a letter, change the cursor to the bottom left arrow and press
the Function Setup switch. Move the cursor over the letter to be edited, move the
cursor to the letter to be inserted and then press the Function Setup switch.
- AREA MODE : Determines whether to use the MD area selected in SENSITIVITY.
- SEL POS : Determines which of the 4 vertices of each MD area is to be used.
- XPOS : Determines the coordinate of the horizontal axis for SEL POS.
- YPOS : Determines the coordinate of the vertical axis for SEL POS.
- FILL→SET : Fills in a selected MD area. The color of the area can be selected from
brown, orange, blue, cyan, green, yellow, magenta and red.
- RETURN : Select this to save the MOTION DET menu settings and return to the SPECIAL menu.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
29
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Your Camera
PRIVACY : Mask an area you want to hide on the screen.
COMM ADJ (Communication Adjustment) :
This function sets up the camera communication status when controlling the camera
PRIVACY AREA SETUP
through an external control device.
1.AREA
2.MODE
AREA1
OFF
GREEN
1
39
79
… 1) …When the SPECIAL menu screen is displayed, press the Function Setup switch
so that the arrow indicates ‘COMM ADJ’.
3.MASK COLOR
4.MASK TONE
5.TOP
6.BOTTOM
7.LEFT
… …2) …Set up the mode using the Function Setup witch.
- CAM ID : Determines the camera's identification
number (between 0 and 255).
- BAUD RATE :You can select 2400/4800/9600/19200
/38400/57600 bps.
- UART MODE :You can select NONE, EVEN or ODD
for the parity bits.
13
52
8.RIGHT
9.RETURN
- RET PKT : Determines whether to send a command
back to the controller device when a
communication control command is sent to the camera.
- DISP ID : Display camera title on top left corner of the screen.
- PROTOCOL :You can select one of various protocols. STW(SPD), PELCO-P, PELCO-D,
VICON, PANASONIC, BOSCH, HONEYWELL, SEC.
1) …When the SPECIAL menu screen is displayed, press the Function Setup switch so
that the arrow indicates ‘PRIVACY’.
… 2…) …Set up the mode using the Function Setup switch.
…
- AREA :You can select up to 12 PRIVACY areas.
- MODE : Determines whether to use the area selected in the AREA.
-
MASK COLOR : Determine area color.You can select Green, Red, Blue, Black,White, Gray.
* Initial value of communication adjustment
- MASK TONE :Adjust the brightness of MASK COLOR.
- TOP/BOTTOM/LEFT/RIGHT :Adjust the size and position of the selected area.
-
Item
Camera ID
1
BAUD RATE UART MODE
9600 8-NONE-1
PET PKT
ENABLE
Initial value
RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL menu.
DIS (Digital Image Stabilizer) :
This function mitigates any picture movement due to external factors such as wind.
LANGUAGE :You can select the menu language according to your requirements.
RETURN : Select this to save the SPECIAL menu settings and return to the MAIN
SETUP menu.
EXIT
Select a desired EXIT mode using the Function Setup Switch.
- SAVE : Save the current settings and exit the MAIN SETUP menu.
- NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu.
Notes
- RESET
: Resets the camera settings to the factory defaults. Language,
Communication and Monitor Settings are not initialized.
• As the DIS function uses the digital zoom the camera's resolution will decrease.
• DIS doesn’t operate when background illumination is too low.
• DIS doesn’t operate when object pattern is monotonic as like sky or white wall.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
31
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Specifications
SIR-4160N
SIR-4160P
If there are problems in operation, please refer to the items below. If the
problem persists, please contact the agent you purchased this product from.
ELECTRICAL
Input Voltage
Power Consumption
VIDEO
Imaging Device
Total Pixels
Effective Pixels
Scanning System
Synchronization
Frequency
DC 12V 10% / AC 24V 10%
Max 6.8W / 6.5W (IR-LED ON)
•
•
•
Nothing appears on the screen.
1/3 inch, Diagonal 6mm Super HAD CCD
811(H) x 508(V)
768(H) x 494(V)
▶Check that the power cord and line connection between the camera and monitor are
fixed properly.
795(H) x 596(V)
752(H) x 582(V)
2:1 Interlace
▶
Check that you have properly connected UTP cable or BNC cable to the camera.
Internal /Line-Lock
The image on the screen is dim.
▶Is lens stained with dirt? Clean your lens with soft, clean cloth.
▶Set the monitor to proper condition.
H : 15.734KHz V:59.94Hz
COLOR : 600TVL, B/W : 700TVL
LED ON : 0Lux
LED OFF : 0.15Lux (Color, F1.2), 0.0003Lux (Color,SENS-UP x512)
50m (32EA)
H: 15.625KHz V: 50.00Hz
Horizontal Resolution
Min. Illumination
▶If the camera is exposed to too strong light, change the camera position.
Visibility distanse(IR LED)
S/N (Y Signal)
Video Output
LENS
Zoom Ratio
52dB (Weight On, AGC Off)
CVBS : 1.0Vp-p, 75Ω composite
The image on the screen is dark.
▶Adjust the contrast feature of the monitor.
3.6x (Manual)
2.8 ~ 10.0mm (F1.2)
▶If you have an intermediate device, set the 75Ω / Hi-z properly.
Focus Length
Angular Field of View
OPERATIONAL
Electronic Shutter Speed
On Screen Display
SSDR
Backlight Compensation
Day & Night
Gain Control
H : 94.4°(Wide) ~ 28°(Tele) / V : 69.2°(Wide) ~ 21°(Tele)
The camera is not working properly, and the surface of the camera is hot.
•
•
▶Check that you have properly connected the camera to an appropriate power source.
1/60 ~ 1/120k sec
1/50 ~ 1/120k sec
NTSC : 7 Languages, PAL : 15 Languages
On / Off (Level adjustable)
BLC / HLC / OFF
COLOR / B/W / AUTO (ICR)
Low / High / Off
ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K)
Auto / Off (Selectable x2 ~ x512)
On / Off (8 Programmable zones)
On / Off (12 Programmable zones)
On / Off (Level adjustable)
On / Off (x1 ~ x16)
On / Off
On / Off (Displayed 15 Characters)
On / Off (Level adjustable)
On / Off
The SENS-UP function does not work.
▶Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
▶Check that SHUTTER of EXPOSURE SETUP menu is ‘A.FLK’ or ‘MANUAL’.
The Motion Detection function does not work.
▶Check that MOTION DET of SPECIAL SETUP menu is ‘OFF’.
•
•
•
•
White Balance
SENS-UP (frame Integration)
Motion Detection
Privacy Masking
3D Noise Filter (SSNRIII)
Digital Zoom
Digital Image Stabilization(DIS)
Camera Title
Sharpness
Color is not correct.
▶Check the setting of WHITE BAL SETUP menu.
The screen flickers continually.
▶Check that direction of camera turns toward the Sun.
Flip / Mirror
Communication
When coaxial communication is not available:
Coaxial, RS-485
▶
▶
Make sure that the camera and monitor are installed within the recommended distance.
Use the video amplifier equivalent to coaxitron if the recommended installation distance is
exceeded.
Coaxial(Pelco), RS-485(STW(SPD), PELCO-P, PELCO-D, VICON, PANASONIC,
BOSCH, HONEYWELL, SEC)
Protocol
ENVIRONMENTAL
Operating Temperature / Humidity
Storage Temperature / Humidity
MECHANICAL
Water Resistance
Dimension
-10°C ~ +50°C / 30% ~ 80% RH
-20°C ~ +60°C / 20% ~ 90% RH
IR-LED isn’t lighted.
•
•
▶
▶
Isn’t DAYNIGHT function setting up the color mode?
Please change the AUTO or B/W mode.
IP66
Ø77mm(W) x 216mm(H) (BRACKET ANGLE 90°), 284mm (BRACKET ANGLE 180°)
1Kg
Weight
The camera is not waterproof.
▶Please check the Front Cover and Main Body by the following Guide Label.
※
The specification for this product may change without prior notice for product improvement.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
33
32
Download from Www.Somanuals.com. All Manuals Search And Download.
DECLARATION OF CONFORMITY
Dimension
Application of Council Directive(s)
89 / 336 / EEC
Manufacturer's Name
Manufacturer's Address
SAMSUNG TECHWIN CO., LTD
SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-716
European Representative Name
European Representative Address
Equipment Type/Environment
Model Name
Ø77
86mm
CCTV Camera
274.7mm
SIR-4160P
Beginning Serial NO.
C10S7010007
Year of Manufacture
2009.07.03
Conformance to
EN 50081-1 : 1992
EMC-Directive 89/336 EEC and 92/31/EEC
EN 50130-4 : 1996
Ø79.8
We, the undersigned, hereby declare that the equipment specified above conforms
to the above Directive(s).
Manufacturer SAMSUNG TECHWIN CO., LTD
Signature
Legal Representative in Europe
Signature
Full Name
Position
Place
Full Name
Position
Place
BONJENG GU
QUALITY CONTROL MANAGER
CHANGWON, KOREA
2009.07.03
Date
Date
244.7mm
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
35
34
Download from Www.Somanuals.com. All Manuals Search And Download.
|