Sony Network Router DMX WL1 User Manual

4-114-319-11(1)  
Startup Guide  
The Startup Guide explains how to connect, setup and use your Wireless Link.  
DMX-WL1  
© 2008 Sony Corporation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting  
1
the Receiver unit  
Attaching the Receiver Unit to the  
Rear of the TV  
3
4
Slide the receiver unit onto the bracket.  
Power off your TV before beginning setup.  
1
Attach the supplied TV Mounting bracket to  
the bottom left side of the TV rear panel.  
Plastic Fastener  
Connect the receiver unit and TV with the  
supplied HDMI cable.  
Guide Pin  
• Do not push on the head of the Plastic Fastener until you  
have inserted the fastener into the hole of the TV.  
OUT  
IN  
IN  
2
Align the slider on the bottom of the receiver  
unit with the groove of the TV Mounting  
bracket.  
5
Connect the AC power adapter with AC  
power cord between the receiver unit and the  
wall outlet.  
DC IN 9V  
to wall outlet  
AC power cord  
AC power adapter  
• See the Reference Guide for information for alternate  
attachment methods.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Choosing  
2
A
your setup type  
Controlling the equipment using the supplied remote control  
Other Equipment  
You can connect up  
to 5 sources to the  
transmitter.  
TV  
Transmitter unit  
Cable Box  
Supplied remote control  
Controlling the equipment using the supplied remote control and sending the  
audio output to your Home Theater System  
B
OPTICAL Cable  
Other Equipment  
TV  
Transmitter unit  
Cable Box  
Supplied remote control  
Controlling the equipment using your Home  
Theater System  
C
Other Equipment  
TV  
Cable Box  
Transmitter unit  
Supplied remote control  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
You can operate equipment  
connected to the transmitter unit  
with the supplied remote control.  
Some equipment may not be  
supported.  
You can operate equipment  
connected to the transmitter unit  
with the supplied remote control.  
Use your Home Theater System  
remote control to control the  
Volume.  
Home Theater System  
Home Theater System remote  
control  
Use your Home Theater System  
remote control to select the sources  
attached to your Home Theater  
System.  
• You cannot operate any equipment connected  
to the transmitter unit with the supplied remote  
control.  
Home Theater System  
Home Theater System remote  
control  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting  
3
the Transmitter unit  
A
IR Blaster  
Transmitter unit  
5
COMPONENT IN  
IR BLASTER  
R
AUDIO  
L
R
-
AUDIO  
-
L
PR  
PB  
Y
(1080i/720p/480p/480i)  
3
DIGITAL AUDIO OUT  
(OPTICAL)  
4
2
1
HDMI  
SERVICE  
DC IN 9V  
IN  
Component  
B
IR Blaster  
HDMI  
Transmitter unit  
5
COMPONENT IN  
IR BLASTER  
R
AUDIO  
L
R
-
AUDIO  
-
L
PR  
PB  
Y
(1080i/720p/480p/480i)  
3
DIGITAL AUDIO OUT  
(OPTICAL)  
4
2
1
SERVICE  
DC IN 9V  
IN  
Component  
OPTICAL AUDIO  
C
HDMI  
HDMI  
Transmitter unit  
5
COMPONENT IN  
IR BLASTER  
R
AUDIO  
L
R
-
AUDIO  
-
L
PR  
PB  
Y
(1080i/720p/480p/480i)  
3
DIGITAL AUDIO OUT  
(OPTICAL)  
4
2
1
SERVICE  
DC IN 9V  
IN  
HDMI  
HDMI  
Component  
Home Theater System  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Place the IR Blaster  
near the IR receiver  
of the equipment.  
Connecting to the  
AC power outlet  
When you finish connecting the equipment  
to the transmitter unit, connect the AC  
power adapter to the wall outlet.  
VCR/DVD/Blu-ray Disc/  
Satellite receiver/  
Cable box  
DC IN 9V  
Transmitter unit  
Place the IR Blaster  
near the IR receiver  
of the equipment.  
to wall outlet  
AC power cord  
AC power adapter  
VCR/DVD/Blu-ray Disc/  
Satellite receiver/  
Cable box  
• Set the output resolution of the equipment to  
480i, 480p, 720p or 1080i.  
If you currently use equipment connected  
directly to your TV with 1080p resolution,  
make sure to change the equipment’s  
resolution to 1080i or less before connecting  
it to the transmitter unit.  
Home Theater System  
You should connect the equipment directly  
to the TV to change the resolution.  
DVD  
Blu-ray Disc  
Cable box  
VCR  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Turning  
4
the TV and the Transmitter unit on  
1
Turn the power of the TV on.  
3
Press POWER on the transmitter unit.  
Set Control for HDMI in the Settings menu  
of the TV On.  
POWER button  
Then select the HDMI input that the receiver  
unit is connected to.  
POWER  
TV  
When the power of the transmitter unit is  
turned on, the POWER LED will light up in  
green, along with the white lamp on the front.  
• If POWER LED of the receiver unit does not light up,  
confirm Control for HDMI setting of the TV is On.  
• The power of the receiver unit turns on or off in  
conjunction with TV, if Control for HDMI setting of the  
TV is On and the unit is connected to the TV by HDMI  
cable.  
POWER LED  
• When Control for HDMI is enabled on your TV, the  
power of the receiver unit will follow the power state of  
the TV. When the TV is turned on or off, the receiver unit  
will also turn on or off. To manually control the power of  
the receiver unit using the receiver’s POWER button, you  
must turn off the TV’s Control for HDMI.  
POWER  
• If Control for HDMI of the TV is Off, you must turn  
the power of the receiver unit on or off by pressing the  
POWER button on the unit.  
• The supplied remote control cannot be used to turn on or  
off the receiver unit separately from the TV.  
White lamp  
2
Confirm the POWER LED automatically lights  
up in green on the receiver unit.  
POWER  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Optimal environment for placement  
of the units  
4
Verify the Wireless LINK LEVEL.  
The LINK LEVEL LEDs located on the front  
of the transmitter unit allows you to verify  
the Wireless LINK LEVEL between the  
transmitter and the receiver units.  
Follow the suggestions below to create an  
optimal environment for your Wireless Link.  
Proper placement of the receiver and transmitter  
units will ensure a strong Wireless LINK LEVEL  
for superior performance.  
LINK LEVEL LED  
LINK LEVEL  
• Use one system per room, placing the  
transmitter and receiver units for each system  
in the same room.  
• If you use a 5 GHz WLAN or cordless phone,  
place those in a different room.  
• Do not place either unit on a metallic rack.  
• Place the transmitter unit as high up as  
possible.  
• Maximum operating distance is approximately  
ꢀ5 feet (20 m), depending on the environment.  
• Be sure to keep at least 1 foot (30 cm)  
minimum distance between the transmitter and  
receiver units.  
When the units are establishing a link, the  
LINK LEVEL LED blinks.  
After the wireless connection is established,  
the LED stops blinking.  
To ensure good picture quality, make  
sure that all three LEDs light up in green,  
indicating a good link.  
Recommended placement of the receiver  
and transmitter units is within ꢀ5 feet (20 m)  
of each other. If you experience problems  
with the LINK LEVEL, removing obstructions  
from the path between the units may improve  
the LINK LEVEL.  
If the Wireless LINK LEVEL is less than three  
or the picture is noisy or the sound quality  
is diminished, press CONNECT to switch to  
another wireless channel.  
If you experience problems finding a suitable  
LINK LEVEL, see the Troubleshooting  
section in the Reference Guide for more  
information.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Running  
5
Initial Setup  
Initial Setup instructions will appear on the  
screen when the receiver and transmitter  
units are turned on for the first time.  
1
Press INPUT SELECT on the transmitter  
unit to highlight your language choice. Then,  
press CONNECT on the transmitter unit to  
continue the setup.  
Initial Setup  
Step 1: Select  
a
language  
Highlight choice by pressing  
a
INPUT SELECT on your  
transmitter. Press CONNECT to  
continue.  
English  
Español  
Français  
INPUT SELECT button  
INPUT SELECT  
CONNECT button  
CONNECT  
• The supplied remote control cannot be used at this  
stage.  
2
Insert batteries into the remote control.  
Push to open  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
On your remote control, press and hold the  
IN 1 button. While holding IN 1, press the  
RETURN button. Hold both for at least 2  
seconds.  
4
Initial Setup is complete.  
Initial Setup  
Activation complete  
To set up IR Blaster, press  
SETUP; otherwise press  
RETURN to exit.  
Initial Setup  
Step2: Activate your remote  
control  
On your remote, press and  
hold IN 1. While holding IN 1,  
press RETURN. Hold both  
for at least  
2
seconds.  
Keep your remote control within  
10 feet of the transmitter.  
To use the supplied remote control to operate  
equipment connected to the transmitter unit,  
proceed to the next page.  
• To display Initial Setup again, press CONNECT and  
INPUT SELECT on the transmitter unit simultaneously.  
IN 1  
IN 1 button  
RETURN button  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Configuring  
6
the remote control  
Configure the IR Blaster to control your  
connected equipment using the supplied  
remote control.  
1
2
3
Press SETUP on the remote control to  
display the Setup menu.  
Setup  
You can control connected equipment  
with your remote by using the IR Blaster  
(supplied).  
IR Blaster  
Language  
HDMI  
HDMI  
HDMI  
HDMI  
1
2
3
4
Component  
If you chose setup type C, you cannot use the  
IR Blaster to control connected equipment.  
Exit the Setup menu by pressing SETUP on  
the remote control to skip these steps.  
Software Version  
1.00.00  
Press to highlight IR Blaster, and press  
. The following screen appears.  
Setup/IR Blaster  
HDMI  
HDMI  
HDMI  
1
2
3
2-8  
Press to highlight an input to configure,  
and press  
.
Setup/IR Blaster/HDMI  
1
Categor y  
Maker  
Code  
Test (Power On/Off)  
Save and Exit  
Open the lid of the  
remote control  
SETUP  
1
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Press to highlight Category (equipment  
type), and press  
Select an equipment type from the list, and  
press  
7
Press to highlight Test (Power On/Off)  
and press  
Test to see if the selected equipment power  
turns on and off.  
.
.
.
You may need to test more than one code to  
find the right code for your equipment.  
Setup/IR Blaster/HDMI  
1
Categor y  
Maker  
Cable Box  
Satellite  
VCR  
• If the equipment’s supplied remote control has both  
POWER ON and POWER OFF buttons, using Test  
(Power On/Off) might not work to test the IR code.  
Select Save and Exit then check if any other remote  
buttons will operate your equipment.  
Code  
Test (Power  
DVD  
Save and Ex BD  
Receiver  
Setup/IR Blaster/HDMI  
1
Categor y  
Maker  
BD  
Sony  
5
6
Press to highlight Maker, and press  
Select a manufacturer from the list, and press  
.
.
Code  
BD  
1
Test (Power On/Off)  
Save and Exit  
Setup/IR Blaster/HDMI  
1
Categor y  
Maker  
Sony  
LG  
Code  
Panasonic  
Philips  
8
When you have found the right code, press to  
highlight Save and Exit, and press  
Save the setting and exit from the Setup  
Test (Power  
.
Save and Ex Pioneer  
Samsung  
menu.  
Setup/IR Blaster/HDMI  
1
Categor y  
Maker  
BD  
Press to highlight Code, and press  
Select a code from the list, and press  
.
.
Sony  
Code  
BD  
1
Test (Power On/Off)  
Save and Exit  
Setup/IR Blaster/HDMI  
1
Categor y  
Maker  
BD  
BD  
BD  
1
2
3
Code  
Test (Power On/Off)  
Save and Exit  
• Do not connect two of the same equipment from  
the same manufacturer (Eg. two Sony Blu-ray disc  
players), you will not be able to control each equipment  
individually.  
See page 15 on Reference Guide if your  
code is not on the list.  
• To erase the code, select Category, then press to  
highlight “----” and press  
in step 4.  
• When more than one code is available for your  
manufacturer, start checking from the top of the list for  
the code that operates your equipment.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using  
7
the supplied remote control  
Operating your TV  
TV POWER  
The following buttons are for operating your TV.  
Press the TV button before using them.  
TV  
Button  
Description  
TV POWER  
TV  
Press to turn the TV on and off.  
You must first press the TV function  
PICTURE WIDE  
FREEZE  
button to operate the TV.  
INPUT  
Press to select the input of the TV.  
Press to change the picture mode.  
Press to change the wide mode.  
PICTURE  
WIDE  
FREEZE  
Press once to display a frozen image  
with the current program in a window.  
Press again to return to the current  
program.  
MENU  
1
4
7
2
5
8
0
3
6
9
0-9, ENT  
Press 0-9 to select a channel; the  
channel changes after two seconds,  
press ENT to change channels  
immediately.  
ENT  
CH +/-  
Press to scan through channels.  
Press to display the TV Home menu.  
Press to adjust the volume.  
VOL  
CH  
HOME/MENU  
VOL+/-  
MUTING  
MUTING  
Press to mute the sound. Press again or  
press VOL+ to restore the sound.  
Press the SETUP button to display the Setup  
menu if you need to change Language or IR  
Blaster settings.  
CONNECT SETUP  
If the Wireless LINK LEVEL is less than three or  
the picture is noisy, press CONNECT to switch to  
another wireless channel.  
• You can use the SETUP or CONNECT buttons when any input is  
selected.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating equipment connected  
to the transmitter unit  
• You must connect the IR Blaster and complete setup for all connected  
equipment before you can operate them.  
The connected  
AV POWER 
HDMI  
POWER  
equipment can be  
operated without  
aiming the remote  
control directly at  
the equipment.  
1
2
Press POWER to turn the transmitter unit on.  
IN 1  
IN 2  
IN 3  
IN 4  
COMPO-  
Press IN 1-4 HDMI or IN 5 COMPONENT to  
select the desired input source.  
NENT  
IN 5  
3
Press AV POWER to turn on the equipment  
connected to the selected input source.  
Button  
Description  
/   
Goes to the beginning of the previous/  
next title/chapter/scene/track.  
/
Replays the scene/briefly fast forwards  
the scene.  
MENU  
/   
Fast reverses/fast forwards the disc  
when pressed during playback.  
Plays a disc at normal speed.  
Pauses the playback.  
Stops the playback.  
HOME/MENU  
Displays menus of selected external  
equipment.  
Moves the on-screen cursor of selected  
  
external equipment. Press  
confirm an item.  
to select/  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ForYour Convenience  
Please contact Sony Customer Support directly if you:  
• Have questions on the use of your module after reading the Startup Guide or Reference Guide  
• Experience difficulty operating your module  
For United States  
or to speak with a support representative: 1-866-918-2485  
For Canada  
or to speak with a support representative: 1-877-899-SONY (7669)  
Sony will work to resolve your questions more quickly than your retailer or place of purchase.  
Please Do Not Return the Product to the Store  
On-line Registration  
United States  
Canada  
Printed in Japan  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sony Camcorder Accessories VCT 870RM User Manual
Sony Cordless Telephone SPP IM977 User Manual
Sony Home Theater System CMT GPX9DAB User Manual
Sony Stereo Receiver FN User Manual
Sony TV Receiver XT 63V User Manual
Sunbeam Bread Maker EXPRESS BAKETM Breadmaker User Manual
Sunrise Medical Stroller Xpress User Manual
Suunto Watch X9_en User Manual
T+A Elektroakustik Stereo Amplifier PA 820 M User Manual
TANDBERG Computer Monitor 1 User Manual