4-246-924-11(1)
Compact Disc
Recorder
Operating Instructions
Owner’s Record
The model and serial numbers are located on the rear of the unit. Record the serial
number in the space provided below. Refer to them whenever you call upon your Sony
dealer regarding this product.
Model No.
Serial No.
RCD-W2000ES
©2003 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Getting Started
Recording/Editing
Unpacking ............................................. 6
Before Recording ................................ 21
Hooking Up the System ........................ 6
This Unit Can Use
Synchro-Recording a CD to CD-R or
CD-RW ......................................... 23
the Following Discs ........................ 7
Recording on a CD-R or CD-RW
Manually ....................................... 26
Adjusting the Recording Level............ 28
Marking Track Numbers While
Basic Operations
Playing a CD ......................................... 8
Playing a disc with MP3 files ................ 9
Using the Display ................................ 13
Locating a Specific Track.................... 15
Recording ...................................... 29
Fading In and Out recording
(Rec Fader) .................................... 30
Finalizing a CD-R or CD-RW ............. 30
Locating a Particular Point
Unfinalizing a CD-RW ........................ 31
Erasing Tracks of a CD-RW ............... 32
Labeling Tracks/Discs ......................... 33
Useful Tips for Recording ................... 34
in a Track ...................................... 16
Playing Tracks/Discs Repeatedly
(Repeat Play) ................................. 17
Playing in Random Order
(Shuffle Play) ................................ 18
Additional Information
Creating Your Own Program
(Program Play) .............................. 19
Using the Menu ................................... 36
Messages ............................................. 37
Self-diagnosis Function ....................... 38
System Limitations .............................. 39
Troubleshooting................................... 39
Specifications ...................................... 41
Playing Both Deck Simultaneously
(Dual Play) .................................... 20
3
Download from Www.Somanuals.com. All Manuals Search And Download.
On condensation in the unit
Welcome
If the unit is brought directly from a cold to a warm
location, or is placed in a very damp room, moisture
may condense on the lenses inside the unit. Should
this occur, the unit may not operate properly. In this
case, remove the CD, CD-R, or CD-RW and leave the
unit turned on for about an hour until the moisture
evaporates.
Thank you for purchasing this Sony Compact
Disc Recorder. Before operating the unit,
please read this manual thoroughly and retain it
for future reference.
On handling discs
• To keep the disc clean, handle it by its edge. Do
not touch the surface.
About This Manual
• Do not stick adhesive papers or tapes onto the disc.
Conventions
• Instructions in this manual describe the controls on
the unit. You can also use the controls on the
remote if they have the same or similar names as
those on the unit.
• The following icon is used in this manual:
Indicates that you can do the task using
• If there is glue or a similar substance on the disc,
remove it completely before using the disc.
Z
the remote.
On storage
Precautions
• Do not expose the disc to direct sunlight or heat
sources such as hot air ducts, nor leave it in a car
parked in direct sunlight as there can be a
considerable rise in temperature inside the car.
• Store discs in their cases. Do not store discs either
stacked horizontally or standing vertically without
their cases.
On safety
• Should any solid object or liquid fall into the
cabinet, unplug the unit and have it checked by
qualified personnel before operating it any further.
• The use of optical instruments with this product will
increase eye hazard.
On cleaning
• Fingerprints or dust on the disc may cause poor
sound reproduction or sound dropout.
• Before playing a disc, clean it with a cleaning cloth.
Wipe the disc from the center out.
On power sources
• Before operating the unit, check that the operating
voltage of the unit is identical with your local power
supply. The operating voltage is indicated on the
nameplate at the rear of the unit.
• The unit is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet, even if the unit itself has been turned off.
• If you are not going to use the unit for a long time,
be sure to disconnect the unit from the wall outlet.
To disconnect the AC power cord, grasp the plug
itself; never pull the cord.
• If the disc is still dirty after being wiped with a
cleaning cloth, wipe it again with a slightly
moistened cloth. Then wipe off the residual
moisture with a dry cloth.
• AC power cord must be changed only at the
qualified service shop.
• Do not use solvents such as benzene, thinner,
commercially available cleaners, or antistatic spray
intended for vinyl LPs.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Note on discs
With the following kinds of discs, you may
experience a reading failure or noise when recorded
to a CD-R or CD-RW.
Note on High-Speed
Synchro-Recording
When recording a CD, certain conditions
may cause the sound to dropout, noise in the
recording, or even unwanted tracks on the
CD-R or CD-RW. If this happens, clean the
CD as described in “On cleaning” above, and
record to the CD-R or CD-RW using normal
speed Synchro-Recording only.
– Discs with adhesive labels attached to them
– Irregularly shaped discs (for example, heart or star
shaped)
– Discs with heavy printing on only one section (may
effect the balance of the disc in the disc tray)
– Old discs
– Scratched discs
– Dirty discs
– Warped discs
Note on CD-R or CD-RW
playback
Playback of a CD-R or CD-RW recorded by
a CD-R or CD-RW recorder may not be
possible depending on the recording
conditions (e.g., dirty disc, etc.). Also,
please note that you need to finalize a CD-R
or CD-RW before playing it back on DECK
A of this unit or a system other than the one
used to make the recording. (Finalizing is a
process to complete the recording.)
After finalizing a CD-R, you can play it in
any conventional CD player. However,
depending on the state of the recording, the
sound may skip during playback.
After finalizing a CD-RW, you can play it in
a CD-RW compatible player only.
Music discs encoded with
copyright protection
technologies
This product is designed to playback discs
that conform to the Compact Disc (CD)
standard. Recently, various music discs
encoded with copyright protection
technologies are marketed by some record
companies. Please be aware that among those
discs, there are some that do not conform to
the CD standard and may not be playable by
this product.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Hooking Up the System
Unpacking
This section describes how to hook up the unit
to an amplifier. Be sure to turn off the power of
each component before making the
connections.
Check that the following items are included:
• Audio connecting cords
Phono plug × 2 (red/white) y Phono plug ×
2 (red/white) (2)
• Remote commander (remote) (1)
• R6 (size AA) batteries (2)
Connecting the unit to an
amplifier
Connect the amplifier to the ANALOG IN/
OUT jacks using the audio connecting cords
(supplied), making sure to match the color-
coded pins to the appropriate jacks on the
components: red (R) to red and white (L) to
white. Be sure to make connections firmly to
prevent hum and noise.
Inserting batteries into the
remote
You can control the unit using the supplied
remote.
Insert two R6 (size AA) batteries by matching
the 3 and # ends on the batteries to the
markings inside the compartment. When using
the remote, point it at the remote sensor on
the unit.
Audio connecting cords (supplied) (2)
White (L)
White (L)
Red (R)
Red (R)
RCD-W2000ES
L
L
L
R
R
R
IN
OUT 2
ANALOG
OUT 1
Tip
With normal use, the batteries should last for about
six months. When the remote no longer operates the
unit, replace both batteries with new ones.
Notes
• Do not leave the remote near an extremely hot or
humid place.
OUT
IN
• Do not drop any foreign object into the remote
casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light from
the sun or lighting apparatus. Doing so may cause a
malfunction.
L
R
TAPE/MD
l: Signal flow
Amplifier
• If you don’t use the remote for an extended period
of time, remove the batteries to avoid possible
damage from battery leakage and corrosion.
Notes
• Be sure to connect the amplifier to the OUT 2 jack.
• Be sure to set the DUAL MODE to off.
Connecting the unit to 2
amplifiers
You can output the sound of DECK A to OUT
1 and that of DECK B to OUT 2 at the same
time (DUAL PLAY. See page 20).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the unit to a
digital component
This Unit Can Use the
Following Discs
Connect a component such as digital amplifier,
CD player, DAT deck, or MD deck through
the DIGITAL OPTICAL IN/OUT jacks (S/
PDIF square type) or DIGITAL COAXIAL
IN/OUT jacks with a optical digital cord (not
supplied) or a coaxial digital cord (not
supplied). Plug in the cord.
The unit can use three types of discs as
follows:
Audio CDs
Discs with these logos can be played by
both DECK A (the CD player section)
and DECK B (the CD-R or CD-RW
recording section) of the unit.
Optical digital cord (not supplied)
Coaxial digital cord (not supplied)
Audio CD-R
Discs with this logo are recordable
only one time. When you finalize the
disc (page 30), you can play it in either
DECK A (the CD player section) or
DECK B (the CD-R or CD-RW
Connecting the AC power
cord
recording section), or any conventional CD player
(you may not be able to play it in some CD players),
including home, car, and portable models. (An
unfinalized disc can be played only in DECK B.)
When you buy a CD-R, please note that you must buy
an audio CD-R. A CD-R designed for computer use
will not work in this unit.
Connect the AC power cord to a wall outlet.
Notes
• Be sure to place the player on a flat, horizontal
place. If the player is left on a slanted position, it
may cause a malfunction or damage the player.
Audio CD-RW
Discs with this logo are recordable,
and also re-w ritable. When you
finalize the disc (page 30), you can play
it in either DECK A (the CD player
section) or DECK B (the CD-R or CD-
RW recording section), and CD-RW compatible
players. They will not play back in most current CD
players unless the player is CD-RW compatible. (An
unfinalized disc can be played only in DECK B.)
When you buy a CD-RW, please note that you must
buy an audio CD-RW. A CD-RW designed for
computer use will not work in this unit.
• If the following occurs during CD playback or
recording, a reading error may occur or noise may
be produced in the recorded results:
– The disc tray or other part of the system is
bumped.
This logo means that an unit is
compatible with Audio CD-R and
Audio CD-RW (both Audio CD-R and
Audio CD-RW can be used).
– The system is placed on an uneven or soft
surface.
– The system is located near a speaker, door, or
other source of vibration.
Note
On this player, you can play MP3 files on DECK A
only. For details, see “Playing a disc with MP3 files”
on page 11.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
Playing a CD
This unit has two decks.
4 Press OPEN/CLOSE (or one of the DISC
1-5 A buttons for DECK A) and place a
disc on the inner circle of DECK A (or
B). Press OPEN/CLOSE (or A) again to
close the disc tray.
In this manual, the CD player section is just
called DECK A, and the CD-R and CD-RW
recording section is called DECK B.
When using the remote, set DECK A/DECK B
to DECK A to operate DECK A (the CD player
section), or to DECK B to operate DECK B
(the CD-R or CD-RW recording section).
With the label side up
OPEN/CLOSE
POWER
DISC 1-5 A
5 For DECK A, press PLAY MODE
repeatedly to select the Continuous
play mode.
When you
select
The unit plays
ALL DISCS
All discs in the unit consecutively
in the order of the disc number.
N
x
AMS
AMS
X x
N PLAY MODE
X
PLAY MODE
1 DISC/
ALBUM
Only one disc you have selected.
DECK A/DECK B
PLAY MODE
6 Press N (or H on the remote).
The unit starts playing. Adjust the volume on
the amplifier.
To
Do the following:
Stop playback
Pause playing
Press x.
Press X. Press the button again or
press N (or H on the remote)
to resume playing.
H
x
X
./>
Select the disc
(for DECK A)
Press one of the DISC 1-5 buttons.
DISC SKIP
Go to the next disc
Press DISC SKIP on the remote.
(for DECK A) Z
Go to the next
track
Turn AMS* clockwise while the
ALBUM SELECT indicator in the
display is turned off (or press >
on the remote ).
1 Turn on your amplifier and adjust the
volume to the minimum.
Go to the beginning
of the current track
or the preceding
track
Turn AMS counterclockwise while
the ALBUM SELECT indicator in
the display is turned off (or press
. on the remote).
2 Set your amplifier’s input selector to
select this unit.
3 Press POWER.
Remove the disc
Press OPEN/CLOSE (or A),
whichever contains the disc you
want to remove after stopping play.
*AMS: Automatic Music Sensor
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Tips
Playing a disc with MP3
files
• You can start playing from a specific track in step 6.
1 Turn AMS while the ALBUM SELECT indicator
in the display is turned off (or press ./> or
the number buttons on the remote) to select the
track you want to play (see “Using the Display”
on page 13 for details about the displayed
information).
About MP3 files
2 Press N (or H on the remote).
• You can remove or load discs while playing the
MP3 (MPEG 1 Audio Layer-3) is a standard
technology and format for compressing audio
data. The file is compressed to about 1/10 of its
original size. Sounds outside the range of
human hearing are compressed while the
sounds we can hear are not compressed.
other deck. Press OPEN/CLOSE (or A) of the deck
that is not currently playing to open that tray, and
remove or load a disc.
• The DISC 1-5 button indicator lights orange when
the disc is in the tray. The indicator lights to green
when the disc is selected.
• You can connect headphones to the PHONES jack
on the front panel. Turn the PHONE LEVEL
control to adjust the volume.
• You can replace any discs in the other disc trays
while playing a disc in DECK A. Press A of the
deck that is not currently playing to open that tray,
and remove or load a disc (Ex-Change function).
Playback of some MP3 files may not be
possible, depending on the encoding.
The encoding method (i.e., the bit rate selected
for encoding) will affect the sound quality of
the MP3 files created. The bit rate typically
used for MP3 files is 128 kbps.
Notes
About ID3 tag
ID3 tag is the text information (track title, album
title, artist name, etc.) stored in the MP3 files.
• You cannot play both decks simultaneously. If you
start playing a disc while playing a disc on another
deck, the playback of former deck stops.
• You can play unfinalized CD-Rs or CD-RWs only
in DECK B. For the detailed explanation about
finalizing, see “Finalizing a CD-R or CD-RW” on
page 30.
• Be sure to close the disc trays when the unit is not
in use to prevent dust and dirt from entering and
prevent damage to the disc tray.
Notes on discs
You can play MP3 files recorded on CD-ROMs, CD-
Rs (recordable CDs), and CD-RWs (rewritable CDs).
The disc must be in the ISO 9660*1 level 1 or level 2
format, or Joliet or Romeo in the expansion format.
You can use a disc recorded in Multi Session*2.
• When you turn on the unit, you will hear some
mechanical noise from the unit. This is not a
malfunction.
• The play mode setting is canceled when you turn
the unit off.
*1ISO 9660 Format
The most common international standard for the logical
format of files and folders on a CD-ROM.
There are several specification levels. In Level 1, file
names must be in the 8.3 format (no more than eight
characters in the name, no more than three characters in
the extension “.MP3”) and in capital letters. Folder names
can be no longer than eight characters. There can be no
more than eight nested folder levels. Level 2
specifications allow file names up to 31 characters long.
For Joliet or Romeo in the expansion format, make sure
of the contents of the writing software, etc.
*2Multi Session
This is a recording method that enables adding of
data using the Track-At-Once method.
Conventional CDs begin at a CD control area called
the Lead-in and end at an area called Lead-out. A
Multi Session CD has multiple sessions, with each
Lead-in to Lead-out segment regarded as a single
session. CD-EXTRA: A format in which CD-DA
(audio) data are recorded in the tracks of session 1
and computer data in the tracks of session 2.
Mixed CD: A format in which computer data are
recorded in the first track and CD-DA (audio) data
in the following tracks within a session.
continued
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
The playback order of the MP3 files
The playback order of the folders and files is as
follows:
• With formats other than ISO 9660 level 1, folder
names or file names may not be displayed correctly.
• When naming, be sure to add the file extension
“.MP3” to the file name.
• If you add the extension “.MP3” to a file other than
MP3, the unit cannot recognize the file properly and
will generate random noise that could damage your
speakers.
Folder (album)
1
1
MP3 files (tracks)
• The following discs take a longer time to start
playback.
– a disc recorded with a complicated tree structure.
– a disc recorded in Multi Session.
2
2
– a disc to which data can be added (non-finalized
disc).
3
3
Cautions when playing a disc that is
recorded in Multi Session
CD-DA (audio) data or MP3 files stored on a Multi
Session CD may be subject to some restrictions on
playback.
4
5
4
– If the disc begins with a CD-DA session, it is
recognized as a CD-DA (audio) disc, and MP3
playback is not possible.
5
6
– If the disc begins with an MP3 session, it is
recognized as an MP3 disc, and playback continues
until a CD-DA (audio) session is encountered.
When the unit recognizes CD-DA data, MP3
playback is not possible.
– The playback range of an MP3 disc is determined
by the tree structure of files produced by analyzing
of the disc.
6
7
7
– A disc with a mixed CD format will be recognized
as a CD-DA (audio) disc.
8
8
9
Tree1
(root)
Tree2
Tree3
Tree4
Tree5
Notes
• This player cannot read the MP3 files if the file
name does not end with the extension “.MP3”.
• Folders that do not include MP3 files are skipped.
• When you insert a disc with many trees, it takes a
longer time to start playback. We recommend that
you make only one or two trees for each disc.
• Maximum total number of MP3 files and folders is
300, and maximum number of folders is 150
(including root folder and empty folders).
• If the maximum number of folders or MP3 files is
exceeded, the additional folders/MP3 files are not
recognized. For example, if you insert the disc with
151 folders, the player reads only 150 folders.
• This unit can play MP3 files in folders nested up to
8 layers deep in the folder tree.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
1 Turn on your amplifier and adjust the
To specify a desired playback order, before the folder
or file name, input the order by number (e.g., “01”,
“02”), then record contents onto a disc. (The order
differs depending on the writing software.)
volume to the minimum.
2 Set your amplifier’s input selector to
select this unit.
Note on playback of MP3 files
3 Press POWER.
Depending on the encoding/writing software,
recording device, or the recording media used at the
time an MP3 file is recorded, you may encounter such
problems as disabled playback, sound interruptions,
and noise.
4 Press one of the DISC 1-5 A buttons
and place a disc with MP3 files. Press
A again to close the disc tray.
Playing a disc with MP3 files
(DECK A only)
This system lets you play discs with MP3 files.
When using the remote, set DECK A/DECK B
to DECK A.
POWER
DISC 1-5 A
With the label side up
5 Press PLAY MODE repeatedly to select
the Continuous play mode.
When you
select
The unit plays
ALBUM AMS
x
X
N
ALL DISCS
All discs in the unit consecutively
in the order of the disc number.
PLAY MODE
1 DISC
Only one disc you have selected.
DECK A/DECK B
PLAY MODE
ALBUM*
All MP3 files in the selected album
on the selected disc.
* When a disc that contains no album is played
with “ALBUM” selected, the disc is played in
the same way as 1 DISC mode.
6 To select an album, press ALBUM until
the ALBUM SELECT indicator in the
display lights up, then turn AMS until
the album you want appears (or press
7 APrLeBsUsMN+/(–oornHthoenrethmeorteem). ote).
The unit starts playing. Adjust the volume on
the amplifier.
H
x
X
./>
ALBUM +/–
continued
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Tips
To
Do the following:
• The function of AMS control changes according to
the ALBUM SELECT indicator in the display. When
the indicator is off, the AMS control selects tracks.
When the indicator lights up, the AMS control
selects albums. Press ALBUM to turn the ALBUM
SELECT indicator on or off.
Stop playback
Pause playing
Press x.
Press X. Press the button again or
press N (or H on the remote) to
resume playing.
Select the disc
(for DECK A)
Press one of the DISC 1-5 buttons.
• You can start playing from a specific track in step 7.
1 Turn AMS while the ALBUM SELECT indicator
in the display is turned off (or press ./> or
the number buttons on the remote) to select the
track you want to play (see “Using the Display”
on page 13 for details about the displayed
information).
Go to the next disc
(for DECK A) Z
Press DISC SKIP on the remote.
Go to the next
track
Turn AMS* clockwise while the
ALBUM SELECT indicator in the
display is turned off (or press >
on the remote ).
2 Press N (or H on the remote).
• You can remove or load discs while playing the
Go to the beginning
of the current track
or the preceding
track
other deck. Press A of the deck that is not currently
playing to open that tray, and remove or load a disc.
• The DISC 1-5 button indicator lights orange when
the disc is in the tray. The indicator lights to green
when the disc is selected.
• You can connect a headphone to the PHONES jack
on the front panel. Turn the PHONE LEVEL
control to adjust the volume.
• You can replace any discs in the other disc trays
while playing a disc in DECK A. Press A of the
deck that is not currently playing to open that tray,
and remove or load a disc (Ex-Change function).
Turn AMS counterclockwise while
the ALBUM SELECT indicator in
the display is turned off (or press
. on the remote).
Go to the next album
Turn AMS clockwise while the
ALBUM SELECT indicator in the
display is turned on (or press
ALBUM + on the remote).
Go back to the
preceding album
Turn AMS counterclockwise while
the ALBUM SELECT indicator in
the display is turned on (or press
ALBUM – on the remote).
Notes
• You can play unfinalized CD-Rs or CD-RWs only
in DECK B. For the detailed explanation about
finalizing, see “Finalizing a CD-R or CD-RW” on
page 30.
Remove the disc
Press A whichever contains the
disc you want to remove after
stopping play.
• Be sure to close the disc trays when the unit is not
in use to prevent dust and dirt from entering and
prevent damage to the disc tray.
* AMS: Automatic Music Sensor
• When you turn on the unit, you will hear some
mechanical noise from the unit. This is not a
malfunction.
• You may not be able to play certain MP3 files.
• When the MP3 file contains ID3 ver.2 tag, it may
take some time to start playback depending on the
size of the ID3 ver.2 tag. “0:00” appears while the
unit is reading ID3 ver.2 tag.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Tips
Using the Display
• When either of the detailed displays are selected,
the disc, track, and album titles are displayed as
follows:
– The disc or album title appears whenever the unit
is stopped.
You can check information about the disc using
the front panel display.
When using the remote, set DECK A/DECK B
to DECK A to operate DECK A, or to DECK B
to operate DECK B.
– The title of the current track appears when a track
is playing.
To label a disc and its tracks, see “Labeling Tracks/
Discs” on page 33.
• You can scroll disc or track titles that do not fit
entirely into the display. Z
DISPLAY
Press SCROLL on the remote to see the rest of the
title. Press SCROLL again to pause scrolling, and
again to continue scrolling.
• When you put a CD containing a CD text in the disc
tray, “CD TEXT” lights up in the display.
TIME
Front Panel Display
TIME
Note
For MP3 files, some characters cannot be displayed.
These characters are displayed as a space or the
system’s original character.
DECK A/DECK B
DISPLAY
SCROLL
TIME
Display while the unit is
stopped
The information appears as follows:
DECK A
Changing the display
When you place a CD/CD-R/CD-RW:
The total track number and total playing time
Press DISPLAY while the unit is stopped or
playing. Each time you press the button, you
can change the display as follows:
CD TEXT
DISC
ALBUM
TRACK
DECK
A
TOC REC
DISC
DECK
B
TRACK
CD TEXT
CD-RW
DECK A/DECK B divided display <
When you place a disc with MP3 files:
m
The total number of MP3 files in the album
DISC
Detailed display for DECK A
m
ALBUM
TRACK
DECK
A
MP3
TOC REC
DISC
DECK
CD TEXT
B
TRACK
CD-RW
Detailed display for DECK B
Tip
The disc title and total number of albums are
displayed just after the unit reads TOC information of
MP3 files.
DECK A/DECK B divided display
CD TEXT
DISC
ALBUM
TRACK
DECK
A
TOC REC
DISC
DECK
CD TEXT
B
TRACK
CD-RW
Notes
• The total playing time is not displayed for MP3
files.
Detailed display for DECK A
CD TEXT
DISC
ALBUM
TRACK
• The ID3 tag is not displayed for MP3 files.
• Maximum total number of MP3 files and folders is
300, and maximum number of folders is 150
(including root folders and empty folders). If the
maximum number of folders or MP3 files is
exceeded, the additional folders/MP3 files are not
recognized.
DECK
A
TOC REC
DISC
DECK
CD TEXT
B
TRACK
CD-RW
Detailed display for DECK B
CD TEXT
DISC
ALBUM
TRACK
DECK
A
TOC REC
DISC
DECK
CD TEXT
B
TRACK
CD-RW
continued
13
Download from Www.Somanuals.com. All Manuals Search And Download.
DECK B
DECK B
When you placed an unfinalized CD-R or CD-
RW in DECK B, you can also check the
remaining recordable time by pressing TIME.
The information appears as follows:
The track number and playing time
CD TEXT
DISC
ALBUM
TRACK
DECK
A
TOC REC
DISC
DECK
CD TEXT
B
TRACK
CD-RW
The total track number and total playing time
CD TEXT
DISC
ALBUM
TRACK
DECK
A
The track number and remaining time of the
track currently being played
TOC REC
DISC
DECK
B
TRACK
CD TEXT
CD-RW
CD TEXT
DISC
ALBUM
TRACK
DECK
A
TOC REC
DISC
DECK
CD TEXT
B
TRACK
CD-RW
The remaining recordable time of the disc (only
the unfinalized CD-R or CD-RW)
CD TEXT
DISC
ALBUM
TRACK
DECK
A
The total remaining time of the disc (in Continuous
play mode)
TOC REC
DISC
DECK
B
TRACK
CD TEXT
CD-RW
CD TEXT
DISC
ALBUM
TRACK
DECK
A
TOC REC
DISC
DECK
CD TEXT
B
TRACK
CD-RW
Display while playing
Press TIME repeatedly while the unit is
playing. Each time you press the button, the
display for any deck that has a disc inside
changes as follows:
Display while recording
Press TIME repeatedly while recording. Each
time you press the button, the display for
DECK B changes as follows:
DECK A
The track number and recording time of the
track currently being recorded
The track number and playing time
CD TEXT
DISC
ALBUM
TRACK
DECK
A
CD TEXT
DISC
ALBUM
TRACK
TOC REC
DECK
A
DISC
DECK
CD TEXT
B
TOC REC
TRACK
CD-RW
DISC
DECK
CD TEXT
B
TRACK
CD-RW
The track number and remaining time of the
track currently being played
The total remaining time of the CD-R or CD-RW
CD TEXT
DISC
ALBUM
TRACK
DECK
A
CD TEXT
DISC
TRACK
TRACK
TOC REC
DECK
A
DISC
DECK
CD TEXT
B
TOC REC
TRACK
DISC
CD-RW
DECK
CD TEXT
B
TRACK
CD-RW
The total remaining time of the disc (in Continuous
play mode)
CD TEXT
DISC
ALBUM
TRACK
DECK
A
TOC REC
DISC
DECK
CD TEXT
B
TRACK
CD-RW
Tips
• When displaying track titles for MP3 files, this
player gives preference to file information in the
following order: ID3 ver.1 tag, ID3 ver.2 tag, MP3
file name. However, the information is not
displayed in this way depending on the disc.
• When the ID3 tag is displayed for MP3 files, “ID3”
lights up. The ID3 tag is consisted of the track title,
album title, and artist name.
Notes
•
The remaining time does not appear for MP3 files.
• The level meter does not appear when playing MP3 files.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Display for disc information
of DECK B
Locating a Specific Track
You can quickly locate any track while playing
a disc by using the AMS (Automatic Music
Sensor) dial on the deck, . and >
buttons on the remote, or number buttons on
the remote.
The indicators show which type of recordable
disc is in the disc tray, and whether the
recordable disc has been already finalized.
TOC indicator
CD TEXT
DECK A
DISC
ALBUM
TRACK
When using the remote, set DECK A/DECK B
to DECK A to operate DECK A, or to DECK B
to operate DECK B.
REC
TOC
DISC
DECK B
CD TEXT
TRACK
CD-RW
CD TEXT
indicator
CD/CD-R/RW
indicator
The CD/CD-R/RW indicator
When you put a CD or finalized CD-R in the
disc tray, “CD” lights up.
N
N
AMS
AMS
When you put an unfinalized CD-R in the disc
tray, “CD-R” lights up.
When you put a CD-RW disc in the disc tray,
“CD-RW” lights up.
DECK A/DECK B
The TOC indicator
When you put an unfinalized CD-R or CD-RW
in the disc tray, “TOC” lights up.
Number buttons/
>10
For details on finalizing, refer to page 30, and
page 31 for unfinalizing.
The CD TEXT indicator
H
When you put a CD containing a CD text in the
disc tray, “CD TEXT” lights up.
./>
ALBUM +/–
When “CD TEXT” is framed in red in the
display of DECK B, CD TEXT information is
not recorded. In this case, finalize the disc to
record the information.
If you remove the disc or turn off the power
before finalizing, CD TEXT information is
erased.
continued
If you try to open the disc tray before
finalizing, “TEXT Edited” appears. You can
open the disc tray if you press OPEN/CLOSE
while the message is displayed.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
To locate
Do the following:
Locating a Particular
Point in a Track Z
The next or
succeeding
tracks
During playback, turn AMS
clockwise while the ALBUM
SELECT indicator in the display is
turned off (or press > on the
remote repeatedly) until you find the
track.
You can locate a particular point in a track
during playback or playback pause.
When using the remote, set DECK A/DECK B
to DECK A to operate DECK A, or to DECK B
to operate DECK B.
The beginning During playback, turn AMS
of the current or counterclockwise while the
preceding tracks ALBUM SELECT indicator in the
display is turned off (or press .
on the remote repeatedly) until you
find the track.
DECK A/DECK B
The next or
succeeding
album
Turn AMS clockwise while the
ALBUM SELECT indicator in the
display is turned on (or press ALBUM
+ on the remote).
The beginning
of the preceding
album
Turn AMS counterclockwise while the
ALBUM SELECT indicator in the
display is turned on (or press ALBUM
– on the remote).
In stop mode, turn AMS while the
ALBUM SELECT indicator in the
display is turned off (or press ./
> on the remote repeatedly) until
you find the track number or track
name, and press N (or H on the
remote).
A specific track
number or track
name directly
m/M
Tip
During playback or pause, press and hold m /
M on the remote.
To pause playing at the beginning of a track, turn
AMS while the ALBUM SELECT indicator in the
display is turned off (or press ./> on the
remote) after pausing playback.
The intermittent sound is heard. (No sound is
heard during pause.) Release the button when
you find the point you want to hear.
Playing directly using the
number buttons Z
You can playback a track directly by using the
number buttons. Press the track number you
want to play. When you select a track number
over 10, press >10 first, then the corresponding
number buttons.
Tip
“-Over-” appears if the disc reaches the end. Turn
AMS counterclockwise (or press . or m on the
remote).
Note
Tracks that are only a few seconds long may be too
short to scan using the search function. For such
tracks, it is better to play the disc at normal speed.
Example:
To enter number 15, press >10, then 1 and 5.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeating only the current
track
While the track you want to repeat is being
played, press REPEAT repeatedly until
“REP1” lights up.
Playing Tracks/Discs
Repeatedly (Repeat Play) Z
You can play tracks repeatedly in any play
mode.
When using the remote, set DECK A/DECK B
to DECK A to operate DECK A, or to DECK B
to operate DECK B.
To stop Repeat Play
Press x.
To cancel Repeat Play
Press REPEAT repeatedly until “REP” and
“REP1” goes off.
DECK A/DECK B
REPEAT
Notes
• When the unit has repeated tracks in the same play
mode five times, playback stops.
• You cannot select “REP” when “ALL DISCS
SHUF” (page 18) is selected.
• The Repeat Play mode is canceled when you turn
the unit off.
H
x
Repeating all tracks on the
disc
Press REPEAT repeatedly until “REP” lights
up in the display, and then press H.
The unit repeats the discs/tracks/MP3 files as
follows:
The deck repeats
When the disc
is played in
All tracks on all discs.
ALL DISCS
Continuous play
(pages 8, 11)
All tracks on the current disc.
1 DISC
Continuous play
(pages 8, 11)
All MP3 files of the current album.
ALBUM
(page 11)
All tracks on the current disc in
random order.
1 DISC SHUF
(for DECK A)/
SHUF
(for DECK B)
(page 18)
All MP3 files of the current album in
random order.
ALBUM SHUF
(for DECK A)
(page 18)
All the same program.
Program Play
(page 19)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Press N (or H on the remote).
“;” appears in the display while the unit is
“shuffling” the tracks, and the track is
played.
Playing in Random Order
(Shuffle Play)
You can have the unit “shuffle” tracks and play
them in random order.
To stop Shuffle Play
Press x.
When using the remote, set DECK A/DECK B
to DECK A to operate DECK A, or to DECK B
to operate DECK B.
To cancel Shuffle Play
While the unit is stopped, press PLAY MODE
until “SHUF” goes off.
PLAY MODE
PLAY MODE
Tip
To play from the beginning of the current track again,
turn AMS counterclockwise while the ALBUM
SELECT indicator is turned off (or press .on the
remote). You cannot go back to tracks that have
already been played.
N
N
x
x
Notes
• If “ALL DISCS SHUF” is selected in the “REP”
setting, “REP” is cancelled (for DECK A).
• You cannot change the PLAY MODE during
playback.
DECK A/DECK B
PLAY MODE
• You can use “ALBUM SHUF” only for discs with
MP3 files.
• The play mode setting is canceled when you turn
the unit off.
H
x
1 While the unit is stopped, press PLAY
MODE repeatedly to select the Shuffle
Play mode as follows:
When you
select
The unit plays
ALL DISCS
SHUF (for
DECK A)
All tracks on all discs in random
order.
1 DISC SHUF
(for DECK A)
All tracks on the current disc in
random order.
SHUF (for
DECK B)
All tracks on the disc in random
order.
ALBUM SHUF
(for DECK A)
All MP3 files of the current
album in random order.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Press ALBUM until ALBUM SELECT
indicator in the display turns off, turn AMS
(or press ./> on the remote) to select
the desired track number, then press AMS
(or PLAY MODE).
Creating Your Own
Program (Program Play)
You can specify the playback order of the
tracks and MP3 files on a disc to create your
own programs containing up to 25 steps.
4 To program additional tracks, repeat
step 3 (steps 2 to 3 for DECK A).
When using the remote, set DECK A/DECK B
to DECK A to operate DECK A, or to DECK B
to operate DECK B.
5 Press N (or H on the remote) to start
Program Play.
The unit starts playing tracks in the
programmed order.
DISC 1-5 A
PLAY MODE
To program all tracks on the
selected disc or album (DECK A
only)
After displaying the first track number in step
3, turn AMS counterclockwise (or press .
on the remote) to select “AL” instead of a track
number. (You cannot program all tracks on the
disc for MP3 files.)
ALBUM
CLEAR
N
x
N
x
AMS
PLAY MODE AMS
DECK A/DECK B
PLAY MODE
To stop Program Play
Press x.
To cancel Program Play
While the unit is stopped, press PLAY MODE
repeatedly until “PGM” goes off.
CLEAR
To erase the last programmed track
H
While the unit is stopped, press CLEAR. (Press
CLEAR on the remote for DECK A.) Each
time you press the button, the last programmed
track is erased.
x
> /
.
ALBUM +/–
DISC SKIP
Tips
• You can also select the track number using the
number buttons on the remote in step 3 above.
• The program remains even after Program Play ends.
When you press N (or H on the remote), you can
play the same program again.
1 While the unit is stopped, press PLAY
MODE repeatedly until “PGM” lights up
in the display.
• To check the total number of the programmed
tracks, press TIME while the unit is stopped.
2 For DECK A, press one of the DISC 1-5
buttons (or DISC SKIP on the remote)
to select the desired disc number.
Notes
• You cannot create a program containing tracks from
both DECK A and DECK B.
3 Turn AMS (or press ./> on the
remote) to select the desired track
number, then press AMS (or PLAY
MODE).
• “Step Full!” appears in the display when you
program over 25 steps. Erase the unnecessary tracks
to enter other tracks.
• The program is erased when you turn the unit off.
• If the total time of the program exceeds 99 minutes
59 seconds, “--.--” appears in the display.
• You cannot change the PLAY MODE during
playback.
To program MP3 files, press ALBUM until
ALBUM SELECT indicator in the display
lights up, then turn AMS (or press ALBUM
+/– on the remote) to select the desired
album title.
• If you program an MP3 track, “--.--” appears in the
display. (The total playing time does not appear for
MP3 files.)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
3 While the unit is stopped, press DUAL
Playing Both Deck
Simultaneously (Dual Play)
MODE.
“DUAL” indicator lights up in the display.
4 Press N (or H on the remote).
The unit starts playing. Adjust the volume
on the amplifier.
If you have 2 amplifiers in different locations
in your house, you can connect the unit to each
amplifier and play two discs simultaneously on
both DECK A and DECK B.
To stop Dual Play
Press x.
The sound of DECK A is output from OUT 1
jacks and the sound of DECK B is output from
OUT 2 jacks.
When using the remote, set DECK A/DECK B
to DECK A to operate DECK A, or to DECK B
to operate DECK B.
Notes
• The front panel display will show you the sound
level of the deck (A or B) you operated last. If you
want to see the other deck’s sound level, press N
(or H on the remote) of the other deck during
playback. In this case, the headphones output will
be also changed to the deck you selected.
• When the DUAL MODE is set to off, the sound of
the deck (A or B) currently playing is output to both
OUT 1 and OUT 2 jacks.
RCD-W2000ES
L
L
L
R
R
R
IN
OUT 2
ANALOG
OUT 1
Tip
As well as the analog connections illustrated in the
left column, you can also enjoy the Dual Play
function when you connect the unit to amplifiers
using the OPTICAL DIGITAL OUT or DIGITAL
COAXIAL OUT connections of the unit.
Amplifier
Amplifier
l: Signal flow
DUAL MODE
DISC 1-5 A
OPEN/CLOSE
N
x
N x
1 Connect the unit to 2 amplifiers.
2 Press OPEN/CLOSE (or one of the DISC
1-5 A buttons for DECK A) and place
the discs you want to play on the inner
circle of DECK A and DECK B. Press
OPEN/CLOSE (or A) of the decks again
to close the disc trays.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording/Editing
About recording MP3 files
Before Recording
• MP3 files are converted to audio CD format before
being recorded to the disc. Thus the amount of data
may increase too much to record on a single disc.
• As this unit recognizes the copyright information
for MP3 files, there are following restrictions.
– You can perform only Normal speed Synchro-
Recording. You cannot make a manual recording.
– The digital data is converted to analog data, then
recorded. You cannot make direct digital
recordings.
About recordable discs
• A recordable disc is an audio CD-R or Audio CD-
RW with the following logo.
– You cannot adjust the recording level.
• The minimum length of CD-DA is 4 seconds.
Therefore, the number of tracks made by the
Synchro-Recording may differ from the original
disc.
• When recording from DECK A to DECK B, the
play and record times shown in the display may be
different. This does not affect the recording.
• The maximum number of tracks is 99 due to the
system limitations of CD format.
• Audio CD-Rs are recordable only one time. Audio
CD-RWs are recordable for multiple times. See
page 7 for details.
About finalization
• Finalization is a final editing process that allows
recorded CD-Rs and CD-RWs to be played in other
players.
• Once a CD-R has been finalized, the recorded
material cannot be changed. The recorded material
on a CD-RW can be altered even after finalizing it.
See page 30 for details.
• Unfinalized discs can only be played back on
DECK B of this unit. See page 7 for details.
Automatic conversion of digital
sampling rates
A built-in sampling rate converter automatically
converts the sampling frequency of various digital
sources to the 44.1 kHz sampling rate. This allows
you to monitor and record sources such as 32 kHz or
48 kHz DAT tape or satellite broadcasts.
About the Serial Copy Management
System
• The Serial Copy Management System allows you to
make only a single copy of a digitally recorded
source. This unit conforms to the Serial Copy
Management System.
continued
• You cannot perform a digital recording from a
digitally recorded CD-R or CD-RW. In this case,
make analog recording.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Types of Recording
The following types of recordings are possible, depending on the audio source. For details on each operation, see
the reference pages.
Automatic Additional CD-TEXT Recording
Finalization Recording
Copy
Level
When recording from DECK A
High-Speed Synchro-
Make-Disc Synchro-
Recording*1
(Make Disc On)
Record all tracks on the
selected disc in the
original order.
Recording*2 (page 24)
Record in high-speed.
You cannot hear the sound
while recording.
∗3
a
×
a
Normal speed Synchro-
Recording (page 25)
Same as
original
Record in normal speed while
monitoring the sound.
High-Speed Synchro-
Synchro-Recording
Recording*2
(Make Disc Off)
Record from one disc or
several discs in the order
you want. You can also
record in programmed
order.
×
×
a
a
×
×
Normal speed Synchro-
Recording
Adjustable
with menu
operation
Manual Recording (page 26)
Record by selecting or editing the tracks manually.
When recording from the component connected to the DIGITAL OPTICAL IN or
DIGITAL COAXIAL IN jack
Manual Recording (page 26)
Adjustable
with menu
operation
×
×
×
a
When recording from the component connected to the ANALOG IN jack
Manual Recording (page 26)
Adjustable
with REC
LEVEL
×
a
*1 Set “Make Disc” in the menu to “On” beforehand (page 36).
*2 Even if you select High-Speed Synchro-Recording, the recording speed automatically changes to normal speed
in the following cases.
– When the disc contains Serial Copy Management System information.
– When the play mode of DECK A is “PGM”.
– When the disc in DECK A contains MP3 files.
*3 Be sure to use a blank disc (that has not been recorded).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Tips
Synchro-Recording a CD
to CD-R or CD-RW
• To play the recorded CD on DECK A or another
CD player, perform finalization (page 30).
• To record your favorite tracks from the CDs in
DECK A, make a program (page 19).
• If the track marks are not marked properly while
making an analog recording from an external
component, see page 29.
You can easily make digital recordings from a
CD to a CD-R or CD-RW. Before recording,
see page 21.
• To record from several discs, see page 26.
There are 2 types of Synchro-Recording.
Notes on recording
• You cannot record over existing material. The unit
automatically starts recording from the end of any
existing material.
• Make sure that the remaining recordable time on the
CD-R or CD-RW is longer than the playing time of
a source CD, especially if you want to record all the
tracks.
• If a message appears in the display, refer to
“Messages” on page 37.
• Recording automatically stops if recording is
paused for more than about 3 minutes.
Make-Disc Synchro-Recording
(Make Disc On)
Records a CD in the original order of its track
number regardless of the selected play mode,
and finalizes the disc. Be sure to use a disc that
has not been recorded. (“Blank Disc” should
appear in the display when you put the disc in
DECK B.)
To use Make-Disc Synchro-Recording, set
“Make Disc” in the Menu to “On” beforehand
(page 36).
Note on a copy protection
Some commercial CD may contain a copy
protection code that will prevent the disc from
being recorded. In this case, “Cannot Copy”
and either “C12” or “C41” will appear
alternately in the display.
• CD text (if contained in the disc) is recorded
automatically. You can label the disc name
or track name (up to 70 characters each, and
40 tracks per disc).
Note
Do not move the unit or disconnect
the unit from power source in the
following situation. Recording may
not complete successfully.
When DECK A is in the Program mode, Make-Disc
Synchro-Recording is canceled regardless of the
menu setting.
Synchro-Recording
(Make Disc Off)
• When “Finalize,” “Unfinalize,” “Erase,” or “OPC”
appears in the display:
The unit is currently updating the table of contents
(TOC).
• When “PMA Writing” appears in the display:
The unit is currently updating the track information.
• After recording, you must finalize the disc.
Until the disc is properly finalized, it cannot
be played on any CD players. See
“Finalizing a CD-R or CD-RW” on page 30.
• CD text contained in the disc is not
automatically recorded on the disc. To label
tracks/discs, see “Labeling Tracks/Discs”
(page 33).
continued
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
High-Speed Synchro-Recording
• You cannot pause recording in Synchro-Recording.
• If Repeat Play is selected, it is automatically
canceled.
• If Shuffle Play is selected, it is automatically
canceled.
• The following functions do not work while
Synchro-Recording:
– Silent Pause function
You can easily make digital recordings from a
CD to a CD-R or CD-RW, faster than normal
speed Synchro-Recording. You cannot monitor
the recorded signal while recording. To use
Make-Disc Synchro-Recording, set “Make
Disc” in the menu to “On” beforehand (page
36).
– Level Sync function
– Manual Track Making function
– Fade-in, Fade-out recording
When using the remote, set DECK A/DECK B
to DECK B.
– Recording level adjustment (the recording level is
set to the same as original disc)
OPEN/CLOSE
POWER DISC 1-5 A
• During Synchro-Recording, the Direct Recording
function is turned on regardless of the menu setting.
• When copying a disc digitally recorded under
control of the Serial Copy Management System
(SCMS), the unit automatically select the analog
recording. High speed recording changes to normal
speed recording. For details on SCMS, see page 21.
• When copying a commercial music CD contains
copy protection code, the unit automatically select
the analog recording. High speed recording changes
to normal speed recording.
N
CD SYNCHRO HIGH
x
• SBM function is available only for analog
recordings (page 35).
DECK A/DECK B
• You cannot stop recording when finalizing in
Make-Disc Synchro-Recording.
CD SYNCHRO
HIGH
H
x
1 Press POWER.
2 Press OPEN/CLOSE of DECK B and
place a recordable CD-R or CD-RW on
the disc tray. Press OPEN/CLOSE of
DECK B again to close the disc tray.
With the label side up
“TOC Reading” appears. The unit starts to
read the TOC (Table of Contents) data and
shows the type of the disc on the deck in the
display.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Press one of the DISC 1-5 A buttons on
DECK A and place a CD on the disc
tray. PressA on DECK A again to close
the disc tray.
Normal speed Synchro-
Recording
The disc is recorded at the same speed as the
playing CD. You can hear the sound during
recording. To use Make-Disc Synchro-
Recording, set “Make Disc” in the menu to
“On” beforehand (page 36).
When you perform Make-Disc Synchro-
Recording, the current disc in DECK A is
used to record.
When you perform Synchro-Recording, you
can choose the disc which you want to
record, and the play mode.
If you select “ALL DISCS” even though
you want to record only one disc, discs you
did not intend to record may be recorded.
K B
t
CD SYNCHRO NORMAL
DECK A/DECK B
4 Press CD SYNCHRO HIGH.
DECK B stands by for recording, and
DECK A stands by for playing.
When you place a CD-R or CD-RW in the
deck, the unit optimizes itself for the best
possible recording and “OPC” appears
temporarily in the display.
N
x
If “Not Blank” appears, make sure that the
blank disc is placed correctly.
CD SYNCHRO
NORMAL
5 After “New Track” appears in the
display, press N on DECK B (or H on
the remote) to start recording.
H
x
High-Speed Synchro-Recording starts.
DECK A and DECK B automatically stop
after recording.
To stop recording
Press x.
Notes
1 Do steps 1 to 3 of “High-Speed
• When you make Synchro-Recording in
programmed order, the recording speed
2 SPryenscshrCoD-RSeYcNoCrdHinRgO” NonORpaMgAeL2.4.
DECK B stands by for recording, and
DECK A stands by for playing.
automatically changes to Normal speed. You can
perform only Normal speed Synchro-Recording.
• If you select “ALL DISCS” even though you want
to record only one disc, discs you did not intend to
record may be recorded.
3 After “New Track” appears in the
display, press N on DECK B (or H on
the remote) to start recording.
Synchro-Recording starts. DECK A and
DECK B will automatically stop after
recording.
continued
25
Download from Www.Somanuals.com. All Manuals Search And Download.
To stop recording
Press x.
Recording on a CD-R or
CD-RW Manually
To record only your favorite CD
tracks
You can record only your favorite CD tracks
using Program Play. Between steps 1 and 2,
perform steps 1 to 4 of “Creating Your own
Program (Program Play)” (page 19).
You can start recording from the end of the
existing material. Before recording, see page
21.
When using the remote, set DECK A/DECK B
to DECK B.
Note
• After recording, you must finalize the disc.
Until the disc is properly finalized, it cannot
be played on any CD players. See
When Program Play is selected, you cannot perform
Make-Disc Synchro-Recording.
To record from several discs
“Finalizing a CD-R or CD-RW” on page 30.
In step 1, set the play mode to “ALL DISCS”
or “PGM” and program the discs you want to
record, then proceed to step 2.
OPEN/CLOSE
INPUT
Notes
• When the play mode is set to “ALL DISCS”, the
recording starts from the disc whose indicator lights
in green. Then the following discs are recorded.
(After Disc 5, Disc 1 is selected).
• If you select “ALL DISCS” even though you want
to record only one disc, discs you did not intend to
record may be recorded.
N
x
REC z
X
DECK A/DECK B
INPUT
REC z
H
X
x
1 Turn on the amplifier and the sound
source, and then select the sound
source on the amplifier.
2 Press OPEN/CLOSE of DECK B and
place a recordable CD-R or CD-RW on
DECK B.
Press OPEN/CLOSE again to close the
disc tray.
With the label side up
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
3 Press INPUT repeatedly to select the
• If you press REC z during recording, you can add
a track number (page 29). The track must be longer
than 4 seconds.
• When recording from more than one disc manually,
the silence between tracks may increase when
changing discs. To prevent this, use Synchro-
Recording.
input connector.
To record through
Turn on the indicator
DIGITAL OPTICAL IN OPT*
DIGITAL COAXIAL IN COAX*
ANALOG IN
ANALOG*
• This unit uses the Serial Copy Management System,
which allows only first-generation digital copies to
be made of premastered software via the unit’s
digital input. Therefore you may not be able to
record a CD-R or CD-RW digitally through the
DIGITAL OPTICAL IN or DIGITAL COAXIAL
IN jack, depending on the content being recorded.
• Because of the restriction of the Serial Copy
Management System (SCMS), you may not be able
to make digital recordings. In this case, use analog
recording through the ANALOG IN jack when you
record from other units. Or use Synchro-Recording
when you record from DECK A. (The recording
mode is automatically changed to analog recording.)
• You cannot make manual recordings of MP3 files.
• While recording the source with “OPT”, “COAX”,
or “ANALOG” selected, you cannot play a disc on
DECK A.
* If a disc is playing on DECK A, stop playback.
To record the disc in DECK A, turn off
“OPT”, “COAX”, and “ANALOG.”
4 Press REC z.
DECK B stands by for recording.
5 Adjust the recording level, if necessary.
For details, see “Adjusting the Recording
Level” on page 28.
6 Press N (or H on the remote).
7 Start playing the sound source you
want to record.
To pause recording
Press X. To resume recording, press the button
again or press N (or H on the remote).
Note
Whenever you pause recording, a new track number
is added. If you paused recording while recording, the
track number increases by one and recording
continues on the new track when recording is
resumed.
To stop recording
Press x.
“PMA Writing” appears while updating the
information of the disc before stopping the
recording.
To play from the beginning of the
disc after recording
1 Press x again while the unit is
stopped.
2 Press N (or H on the remote).
The unit starts playing from the first track.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Press AMS (or YES).
Adjusting the Recording
Level
6 While monitoring the sound, turn AMS
(or press ./> on the remote) to
adjust the recording level, then press
AMS (or YES).
Adjust the recording level within a range of
– ∞ dB to +18 dB, so that the OVER
indication of the peak level meters does not
light red.
Adjusting the recording level
for digital recording
You can adjust the recording level using the
menu. (For details, see “Using the Menu” on
page 36.)
OVER indication
When using the remote, set DECK A/DECK B
to DECK B.
MENU/NO
OVER
DISC
ALBUM
TRACK
DECK
DECK
A
TOC REC DIGITAL
DISC
B
TRACK
CD TEXT
CD-RW
7 Press MENU/NO.
AMS REC LEVEL
8 Stop playing the sound source.
9 To start recording, do steps 6 and 7 of
“Recording on a CD-R or CD-RW
Manually” on page 26.
DECK A/DECK B
YES
MENU/NO
Note
You cannot change the digital optical or coaxial
output level even if you adjust the recording level for
digital recording.
Adjusting the recording level
for analog recording
./>
Turn the REC LEVEL control on the front
panel. Adjust the recording level so that the
OVER indication on the peak level meters does
not light up.
1 Do steps 1 to 4 of “Recording on a CD-
R or CD-RW Manually” on page 26.
2 Play the portion of the sound source
Note
with the strongest signal level.
You can adjust the recording level while recording,
not while playing a disc in DECK B.
3 Press MENU/NO.
4 Turn AMS (or press ./> on the
remote) to select the program source.
To select
Display
DECK A
DECK A Lvl
Optical Lvl
a component connected to
the DIGITAL OPTICAL
IN jack
a component connected to
the DIGITAL COAXIAL
IN jack
Coaxial Lv1
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Marking track numbers
automatically (Track Marking
Function)
Marking Track Numbers
While Recording
The unit adds track marks differently in the
following cases:
You can mark track numbers either manually
or automatically. By marking track numbers at
specific points, you can quickly locate the
points later using the AMS Function or Editing
Functions.
• When you make a Synchro-Recording
(page 23)
The unit marks track numbers automatically under
the control of DECK A.
When using the remote, set DECK A/DECK B
to DECK B.
• When recording from DECK A, or from a
CD or MD connected through the
DIGITAL OPTICAL IN or DIGITAL
COAXIAL IN jack (with “OPT” or
REC z
“COAX” selected by the INPUT button)
The unit marks track numbers automatically
according to the information contained in the source
being recorded. However, the unit may not
automatically mark track numbers when recording
from some CD players and multi disc players.
• In all other cases
When “Track Mark” is set to “LSync” in menu, the
unit marks a new track number whenever the signal
drops to the specified level* or below for about 1.5
seconds or longer, then rises to a specified level.
* The initial setting is –50 dB.
DECK A/DECK B
To turn off the Track Mark Function
While the unit is stopped, set “Track Mark” in
menu to “Off.” For details, see “Using the Menu”
(page 36).
REC z
To change the trigger level for Track
Marking Function (Level Sync function)
While the unit is stopped, select “LSync Lvl” in the
menu and set the level between
–72 dB and –20 dB. For details, see “Using the
Menu” (page 36).
Marking track numbers
manually
You can mark track numbers at any time while
recording. Press REC z at the point you want
to add a track mark.
Notes
• You cannot mark track numbers manually during
Synchro-Recording.
• Track length must be at least 4 seconds to mark
track numbers manually.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Fading In and Out
recording (Rec Fader) Z
Finalizing a CD-R or CD-
RW
You can gradually increase the recording level
at the beginning of a recording (fade-in
recording) or decrease the recording level at the
end of a recording (fade-out recording).
Finalizing completes the recording of a disc. It
enables you to play the disc on DECK A of this
unit or other players. (The CD-RW compatible
player for CD-RW playback.) When a
recording is finished, a CD-R or CD-RW must
be finalized. Once that is done, a CD-R cannot
be added or erased to. CD-RWs are locked
once they are finalized, and must be unfinalized
to permit additional recording or erasure.
This function is convenient when you do not
want the track to start or end abruptly.
Before using the remote, set DECK A/DECK B
to DECK B.
When using the remote, set DECK A/DECK B
to DECK B.
DECK A/DECK B
YES
FINALIZE
N
REC FADER
DECK A/DECK B
YES
Notes
• Fading lasts for 5 seconds.
• You cannot change the digital optical or coaxial
output level even if you make fade-in/fade-out
recording.
• You cannot make fade-in/fade-out recording while
Synchro-Recording.
FINALIZE
H
Fade-in recording
During recording pause, press REC FADER at
the point where you want to start fade-in
recording.
1 Place a CD-R or CD-RW that has not
been finalized in DECK B.
Make sure that “TOC” appears in the
display. If a finalized CD is loaded, “TOC”
does not appear.
“Fade In” flashes in the display, and recording
starts.
2 Press FINALIZE while the unit is
stopped.
Fade-out recording
Finalizing enters standby mode.
During recording, press REC FADER at the
point where you want to start fade-out
recording.
“ Fade Out” flashes in the display, and the unit
fades out and changes to recording pause.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Press N (or H on the remote) or YES.
Unfinalizing a CD-RW
Finalizing starts. During finalizing,
“Finalize” appears in the display and the
remaining time for finalizing (may not be
accurate) appears. When the finalizing
process is finished, the total track number
and total playing time appears in the display
and the TOC (red) indicator goes off.
A finalized CD-RW is neither recordable nor
rewritable. If you want to add new tracks or
erase tracks, you must first unfinalize the disc.
When using the remote, set DECK A/DECK B
to DECK B.
YES FINALIZE
Notes
• Once the finalizing process starts, you cannot stop
in the middle of the process.
• Do not turn off the unit or disconnect the unit from
the power source in the middle of the finalizing
process. Recording will not been complete
successfully, and you will not be able to play back
the recorded tracks.
N
• An unfinalized disc can be played back only in
DECK B.
• You cannot finalize the disc while playing a disc on
DECK A.
DECK A/DECK B
YES
FINALIZE
H
1 Place a finalized CD-RW in DECK B.
Make sure that “TOC” does not appear in
the display. If an unfinalized CD is loaded,
“TOC” appears.
2 Press FINALIZE while the unit is
stopped.
Unfinalizing enters standby mode.
3 Press N (or H on the remote) or
YES.
Unfinalizing starts. During unfinalizing,
“Unfinalize” appears in the display and the
remaining time for unfinalizing (may not be
accurate) appears. When the unfinalizing
process is finished, the total track number and
the total playing time appears in the display
and the TOC (red) indicator lights up.
Notes
• Once the unfinalizing process was started, you
cannot stop in the middle of the process.
• Do not turn off the unit or disconnect the unit from
the power source in the middle of the unfinalizing
process.
• If the disc contains CD-TEXT information stored
on the disc before unfinalizing, it will be erased
when the disc tray is opened or when the power is
turned off.
• You cannot unfinalize the disc while playing a disc
on DECK A.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Turn AMS (or press ./> on the
remote) to select the first track you
want to erase.
Erasing Tracks of a CD-
RW
5 Press N (or H on the remote) or YES.
Erasing starts from the last track. During
erasing, “Tr Erase” appears in the display
and the remaining time for erasing the last
track (may not be accurate) appears. When
this process is finished, the total track
number and the total playing time appears
in the display.
You can erase tracks recorded on a CD-RW.
This process starts with the last track on the
disc.
Before erasing the track, make sure that the
disc is not finalized. If the disc is finalized,
follow the instructions for “Unfinalizing a CD-
RW” (page 31).
Tip
When using the remote, set DECK A/DECK B
to DECK B.
You can erase tracks using the menu.
1 Select “Tr Erase” from the menu (page 36).
To erase only the last track, go to step 3.
2 Turn AMS (or press ./> on the remote) to
select the first track you want to erase.
MENU/NO YES
3 Press N (or H on the remote) or YES.
Erasing starts.
To erase all tracks
AMS
N
1 Place a CD-RW that has not been
finalized in DECK B.
DECK A/DECK B
2 Press ERASE on the remote repeatedly
until “DiscErase?” appears in the
display while the unit is stopped.
YES
3 Press N (or H on the remote) or YES.
Erasing starts. During erasing, “DiscErase”
appears in the display and the remaining
time of erasing (may not be accurate)
appears. When the entire disc is erased,
“Blank Disc” appears.
ERASE
H
./>
Tip
You can erase all tracks using the menu.
1 Select “DiscErase?” from the menu, then press N
(or H on the remote) or YES.
2 “DiscErase??” appears.
3 Press N (or H on the remote) or YES again.
Erasing starts.
1 Place a CD-RW that has not been
finalized in DECK B.
Make sure that “TOC” appears in the
display. If a finalized CD is loaded, “TOC”
does not appear.
Notes
• Once the erasing process has started, you cannot
stop in the middle of the process.
• You can erase only from the last track.
• Do not turn off the unit or disconnect the unit from
the power source in the middle of the erasing
process.
2 Press ERASE on the remote while the
unit is stopped.
“Tr Erase?” appears in the display.
3 Press YES.
• You cannot erase tracks while playing a disc on
DECK A.
The last track is selected.
To erase only the last track, go to step 5.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Press NAME EDIT/SELECT repeatedly
Labeling Tracks/Discs Z
to select the character type as follows:
DISC
ALBUM
TRACK
You can create titles for tracks/discs for a
recorded CD-R or CD-RW with capital and
small letters, numbers, and symbols. You can
enter a disc name of up to 70 characters, and a
track name of up to 70 characters per track, for
40 tracks per disc.
DECK
DECK
A
TOC
DISC
B
TRACK
CD TEXT
CD-RW
To select
Display
Capital letters and symbols*
Small letters and symbols*
Numbers
Selected AB
Selected ab
Selected 12
Label the track/disc before finalizing it. You
cannot label the track/disc on a finalized disc.
After labeling, you must finalize the disc before
you remove the disc or turn off the unit.
Otherwise, the titles will be cleared.
* You can use the following symbols in titles:
’ – / , . ( ) : ! ? & + < > _ = ” ; # $ % @ * `
To enter a space, press 10/0.
When using the remote, set DECK A/DECK B
to DECK B.
7 Press a letter/number/symbol button to
enter a character.
NAME EDIT/
SELECT
DISC
ALBUM
TRACK
DECK A/DECK B
MENU/NO
DECK
A
TOC
DISC
DECK
CD TEXT
B
TRACK
CD-RW
YES
Letter/number/
symbol buttons
To enter a number, press the number button
you want.
CLEAR
To enter a letter or symbol,
1 Press the corresponding letter button
repeatedly until the letter or symbol you
want flashes. You can also enter a letter
or symbol by pressing ./>
x
./>
m/M
repeatedly. To select the symbol, press
> repeatedly after flashing “ ”.
’
2 Press M.
1 Place a CD-R or CD-RW disc that has
8 Repeat steps 6 and 7 until you have
entered the entire title.
not been finalized in DECK B.
If you enter an incorrect character, press
m or M until the incorrect character
starts flashing.
Press CLEAR to erase the incorrect
character, then enter the correct one.
2 Press NAME EDIT/SELECT while the
unit is stopped.
“Name In?” appears in the display.
3 Press YES.
4 Press ./> to select the disc or
9 Press YES.
track you want to label.
“Complete !” appears in the display for a
few seconds and the track or disc is labeled.
Finalize the disc before you remove the disc
or turn off the unit. Otherwise, the titles will
be cleared.
When you label the disc name, select
“Disc,” and when you label the track name,
select the track number.
5 Press YES.
A flashing cursor appears.
DISC
ALBUM
TRACK
To cancel labeling
DECK
A
TOC REC
DISC
Press MENU/NO or x.
DECK
CD TEXT
B
TRACK
CD-RW
continued
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing an existing title
Useful Tips for Recording
1 Do steps 1 to 5 in “Labeling Tracks/
Discs” (page 33) to select the title you
want to change.
When using the remote, set DECK A/DECK B
to DECK B.
MENU/NO YES
SBM
2 Press and hold CLEAR until the current
title is erased.
3 Do steps 6 to 8 of “Labeling Tracks/
Discs” (page 33) to enter the new title.
4 Press YES.
AMS TIME
“Complete !” appears in the display for a
few seconds and the track or disc is labeled.
DECK A/DECK B
SBM
TIME
YES
MENU/NO
./>
Checking the remaining
recordable time on the CD-R
or CD-RW
Press TIME repeatedly.
• Each time you press the button while the unit
is stopped, the display alternates between
total disc playing time and remaining
recordable time on the CD-R or CD-RW
(page 13).
• Each time you press the button while
recording, the display alternates between the
recording time of the current track and the
remaining recordable time on the CD-R or
CD-RW (page 14).
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Silent Pause
function
Using the SBM (Super Bit
Mapping) function
If there has been no sound input for about 30
seconds during recording, the unit pauses
recording.
When performing analog recordings (recording
from ANALOG IN jack, or synchro-recording
MP3 files), the SBM function enables you to
record the equivalent of 24-bit high quality
sound by mapping the initial 24-bit A/D
conversion to 16-bit without reducing the
sound quality. This is made possible by
incorporating a noise-shaping filter in the 24-
bit A/D converter of this unit, which has a
frequency range designed to cover the range of
human hearing.
If the unit continues pausing for about 3
minutes after the Silent Pause Function
activated, recording stops automatically.
Note that this function does not activate if the
unit is Synchro-Recording from a CD on
DECK A.
Tip
You can turn off the Silent Pause Function. For
details, see “Using the Menu” (page 36).
Press SBM. The indicator lights up.
When you press the button again, the function
is canceled and the indicator turns off.
Using the Post Gap function
Notes
You can insert the silence of 2 seconds between
the songs, when recording more than two tracks
at once. The silence is inserted in the following
situations.
• You cannot change the setting while recording.
• When performing digital recordings (recording
from DIGITAL OPTICAL IN jack, or recording
from DECK A), the SBM function is automatically
canceled.
• When recording is stopped.
• When the disc of DECK A changes to the
next disc during Synchro-Recording.
Recording the original sound
from the program source
(Direct Recording)
You can record audio as it is when recording a
digital signals with 44.1 kHz sampling rates
without going through the devices internal
circuits. Set “Direct” in the menu to “On”. For
details, see “Using the Menu” on page 36.
To use the function of adding Post
Gap
Set “Post Gap” of the menu to “On” when the unit is
stopped. For details, see “Using the Menu” on page
36.
Notes
• When recording digital signals with sampling rates
other than 44.1 kHz, the signal will automatically
pass through the device’s internal sampling rate
converter before recording, even when “Direct” is
set to “On”.
• The recording level is set to the setting adjusted in
the menu.
• During Synchro-Recording, the Direct Recording
function works regardless of the menu setting.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
Using the Menu
MENU/NO YES
You can make various settings on this unit by
using the menu.
When using the remote, set DECK A/DECK B
to DECK B.
1 Press MENU/NO.
CLEAR
AMS
2 Turn AMS (or press ./> on the
remote) to select the menu item, and
press AMS (or YES).
3 Turn AMS (or press ./> on the
remote) to set the item, and press AMS
(or YES).
DECK A/DECK B
MENU/NO
4 Press MENU/NO.
YES
To initialize an item’s parameter
Press CLEAR after step 2.
CLEAR
Notes
• The menus you can use while the unit is stopped,
playing, or recording differ.
./>
• The setting is stored in memory even if you turn off
the unit or disconnect the power.
Menu items
Menu item
Function (reference page)
Parameters (Initial setting)
Tr Erase?*
Erase tracks from a disc (page 32).
—
DiscErase?* Erase all tracks from on a disc (page 32).
Make Disc Sets whether Make-Disc Synchro-Recording is performed
—
On/Off (Off)
when using the CD SYNCHRO NORMAL or CD SYNCHRO
HIGH buttons (page 23).
DECK A Lvl Adjusts the input level from DECK A (page 28).
– ∞ dB to +18 dB (0.0 dB)
Optical Lvl Adjusts the input level from the DIGITAL OPTICAL IN jack
(page 28).
– ∞ dB to +18 dB (0.0 dB)
Coaxial Lvl Adjusts the input level from the DIGITAL COAXIAL IN jack
(page 28).
– ∞ dB to +18 dB (0.0 dB)
Track Mark Sets the Track Marking Function (page 29).
LSync/Off (LSync)
LSync Lvl
Changes the trigger level for Track Marking Function (page 29). –72 dB to –20 dB in 2 dB
increments (–50 dB)
Silent Pause Sets the Silent Pause Function (page 35).
On/Off (On)
On/Off (Off)
On/Off (Off)
Direct
Sets the Direct Recording Function (page 35).
Sets the function to add Post Gap (page 35).
Post Gap
* Appears only when an unfinalizes CD-RW is inserted in DECK B.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Explanation
Message
Messages
You have tried the Make-Disc
Synchro-Recording, with a disc
that is not blank.
• Use a blank disc for the Make-
Disc Synchro-Recording.
Not Blank
The following table explains the messages that
appear in the display.
Message
Explanation
OPC
OPC: Optimum Power Control
Blank Disc
A blank CD-R/CD-RW you have
just bought or a CD-RW you have
entirely erased is in the unit.
The unit is optimizing itself for
best possible sound.
OPC Over
The number of times OPC
recording has been performed 90
times.
• Stop the recording and finalize
the disc.
Check Disc
You are trying to record or edit a
finalized disc or CD. Or you are
trying to edit a CD-R.
Complete!
Data Disc
Editing has been completed
successfully.
-Over-
The playback of the last track is
over.
• Turn AMS counterclockwise (or
press . or m on the remote).
You are trying to record or edit a
non audio CD-R/CD-RW.
• Insert an audio CD-R/CD-RW.
Disc Full!
There is not enough time left on the
CD-R/CD-RW or there are no
recordable tracks available to
complete a planned recording.
PMA Writing
Push STOP!
PMA: Program Memory Area
A disc’s information is being
updated.
You operate the unit not in the
STOP mode.
Erase
The ERASE function is operating.
Ex-Change
During CD playback, you remove
and insert another CD.
• Stop the unit, and then operate the
unit again.
Fade In
The FADE IN REC function is
operating.
-Retry-
Recording or editing has been tried
again.
Fade Out
Finalize
The FADE OUT REC function is
operating.
Step Full!
The number of programmed tracks
has reached the limit, and you
cannot program any more tracks.
The FINALIZE function is
operating.
• Before you program a new track,
erase the current program and
restart a new program procedure.
Incomplete!
Editing has not completed
successfully due to vibration of the
unit or a dirty or scratched disc.
TEXT Edited
A disc whose text has been edited
but has not been finalized is
inserted, and OPEN/CLOSE has
been pressed.
Initialize
The unit does not memorize the
menu settings or the previous
playback state.
Name Full!
The number of characters used for
the track or disc names is beyond
the maximum.
• Finalize the disc, and then press
OPEN/CLOSE to remove the
disc. If you want to remove the
disc before finalizing it, press
OPEN/CLOSE again while
“TEXT Edited” is displayed.
-NO DISC-
No Name
There is no disc in the unit.
There is no title.
Unfinalize
The UNFINALIZE function is
operating.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
C71/
Din Unlock
If this message is displayed
momentarily, this is not an error. It
is caused by the digital signal
during recording.
Self-diagnosis Function
When the self-diagnosis function is activated to
prevent the player from malfunctioning, three
character service numbers in a combination
with a message appears in the display. In this
case, check the following table.
During recording of a digital sound
source, the connecting cable has
been disconnected or the player of
the sound source has turned off.
• Connect the cable or turn on the
digital player.
Message
Explanation
C12/
Cannot Copy
You are trying to record a disc that
cannot be played back in DECK-A
or with an external device, such as
CD-ROM or VIDEO CD.
• Remove the disc, and then insert a
music CD for playback.
C13/
Rec Error
Recording has not been completed
successfully because of vibration.
• Relocate the unit in a place free of
vibration and restart the recording
again.
The disc you try to record is
excessively dirty (such as oil-
stained or finger marked) or
scratched. Or the disc is not
normal.
• Replace the disc with another one
and restart the recording again.
C14/
TOC Error
The unit did not read the TOC
information.
• Insert other discs.
C41/
Cannot Copy
The sound source you are trying to
record is a copy of a commercial
music software. Or you are trying
to record on a CD-R/CD-RW
digitally.
• Because of the restriction of the
Serial Copy Management System,
you cannot record copies of
commercial music software or
MP3 files on DECK A. Neither
can you digitally record from a
CD-R/CD-RW.
• Use analog recording through the
ANALOG IN jack when you
record from other units. Or use
Synchro-Recording when you
record from DECK A. (The
recording mode is automatically
changed to analog recording.)
38
Download from Www.Somanuals.com. All Manuals Search And Download.
System Limitations
Troubleshooting
If you experience any of the following
difficulties while using the unit, use this
troubleshooting guide to help you remedy the
problem.
“TOC Reading” appears in the
display for a long time
Regardless of the disc, “TOC Reading” appears in the
display of DECK B longer than in that of DECK A.
This is because, DECK B is a CD-R/RW writer and
reads various version information while setting
optimum recording condition.
DECK A (the CD player
section)
Limitations when recording over an
existing track
• The correct remaining recording time may not be
displayed.
The player does not start playing.
• Insert a disc.
• Place the disc properly.
• The remaining recording time may be inaccurately
displayed relative to the total recorded time.
• You can record up to 99 tracks.
• Clean the disc (page 4).
• Place the disc with the label side up.
• Moisture condensation has formed inside the
unit. Take the disc out and leave the unit turned
on for about an hour until the moisture
evaporates (page 4).
Note
When you turn on the unit, you will hear some
mechanical noise from the unit. This is not a
malfunction.
• Press POWER to turn the unit on.
DECK A (MP3 playback)
MP3 files cannot be played back.
• Recording was not performed according to the
ISO 9660 level 1 or level 2 format, or the Joliet
or Romeo in the expansion format.
• The file extension “.MP3” is not added to the file
name.
• Files are not stored in MP3 format.
MP3 files take longer to play back than others.
• The following discs take a longer time to start
playback.
– a disc recorded with complicated tree structure.
– a disc recorded in Multi Session.
– a disc to which data can be added (non-
finalized disc).
continued
39
Download from Www.Somanuals.com. All Manuals Search And Download.
DECK B (the CD-R and CD-RW
recording section)
Other
No sound is output.
• Make the connections properly (page 6).
• Operate the amplifier properly.
The unit does not operate or operates poorly.
• The CD-R or CD-RW may be damaged. Replace
the disc.
• When using the headphones, turn PHONE
LEVEL to turn up the output level.
The player does not start playing.
• Check the DUAL MODE setting. When the
DUAL MODE is activated, the unit outputs the
sound of DECK A to OUT 1 jacks and that of
DECK B to OUT 2 jacks (page 20).
• Place the CD-R or CD-RW with the label side
up.
• Moisture has formed inside the unit. Take the
disc out and leave the unit in a warm place for
several hours until the moisture evaporates (page
4).
The remote does not operate the unit.
• Make sure that there are no obstacles between the
unit and the remote.
• Press POWER to turn the unit on.
• Point the remote at the remote sensor on the unit.
• Replace the batteries in the remote.
• Replace the CD-R or CD-RW with one that has
been recorded.
The player does not start recording.
• The CD-R or CD-RW is finalized. Unfinalize
(for CD-RW only) the disc (page 31) and try
again.
When you turn on the unit, you will hear some
mechanical noise from the unit. This is not a
malfunction.
• Make connections properly to the sound source
(page 6).
After you have attempted the
prescribed corrective actions
• The sound source is not connected to the selected
input connector. Select the correct input using
the INPUT button (page 27).
If the unit still does not operate properly, or if
other problems not described above occur, turn
off the unit, unplug it from the power outlet for
a few minutes, then reinsert the plug into the
power outlet.
• The recording level is set too low. Adjust the
recording level properly (page 28).
• There has been a power failure or the AC power
cord has been disconnected during recording.
Data recorded to that point may be lost.
The sound has a lot of static.
Strong magnetism from a television or a similar
device is interfering with operations. Move the unit
away from any sources of strong magnetism.
Should any problem persist even after
reinserting the power plug, consult your nearest
Sony dealer.
MP3 files cannot be played back.
• You cannot play MP3 files on DECK B.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
General
Power requirements
Power consumption
Specifications
120 V AC, 60 Hz
28 W
Dimensions (approx.) (w/h/d) incl. projecting parts
and control
430 × 110 × 400 mm
(17 × 4 3/8 × 15 3/4 inch)
7.9 kg
DECK A (the CD player section)
System
Compact disc digital audio
system
Mass (approx.)
(17 lbs 7 oz)
Laser
Semiconductor laser
(λ = 780 nm)
Supplied accessories
See page 6.
Emission duration:
continuous
Design and specifications are subject to change
without notice.
Playable discs
Frequency response
CD, CD-R, CD-RW
20 Hz – 20,000 Hz
(±0.5 dB)
Signal to Noise Ratio
Wow and flutter
Over 100 dB during play
Below measurable limit
DECK B (the CD-R and CD-RW
recording section)
System
Compact disc digital audio
system
Laser
Semiconductor laser
(λ = 780 nm)
Emission duration:
continuous
Playable discs
Recordable discs
CD, CD-R, CD-RW
CD-R, CD-RW (for
Audio)
Frequency response
20 Hz - 20,000 Hz
(±0.5 dB)
Signal to Noise Ratio
Wow and flutter
Over 100 dB during play
Below measurable limit
Inputs
ANALOG IN
(Phono jacks)
Impedance: 47 kilohms
Rated input: 500 mVrms
Minimum input:
250 mVrms
DIGITAL OPTICAL IN
(Square optical connector jack)
Optical wavelength:
660 nm
DIGITAL COAXIAL IN
(Phono jack)
Impedance: 75 ohms
Rated output: 0.5 Vp-p,
±20 %
Outputs
ANALOG OUT 1, OUT 2 Rated output: 2 Vrms
(Phono jacks)
Load impedance: over
10 kilohms
DIGITAL OPTICAL OUT 1, OUT 2
(Square optical connector jack)
Wavelength: 660 nm
Rated output: –18 dBm
DIGITAL COAXIAL OUT 1, OUT 2
(Phono jacks)
Rated output: 0.5 Vp-p,
±20 %
Load impedance: 75 ohms
Load impedance: 32 ohms
Rated output: 28mW
PHONES
(Stereo phone jack)
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Sony Corporation
Printed in Malaysia
Download from Www.Somanuals.com. All Manuals Search And Download.
|