Sony Laptop MVS8000SF C User Manual

SWITCHER PROCESSOR PACK  
MVS8000SF-C  
MULTI FORMAT SWITCHER PROCESSOR  
MVS-8000SF  
HK-PSU04  
MKS-8110HD  
MKS-8160HD  
MKS-8170HD  
MKS-8210HD  
MKS-8440HD  
MKS-8210K1  
MKS-8110SD  
MKS-8160SD  
MKS-8170SD  
MKS-8210SD  
MKS-8440SD  
MKS-8440K1  
MKS-8110M  
MKS-8160M  
MKS-8170M  
MKS-8210M  
MKS-8440M  
MKS-8420M  
INSTALLATION MANUAL  
1st Edition (Revised 2)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Attention-when the product is installed in Rack:  
1. Prevention against overloading of branch circuit  
When this product is installed in a rack and is  
supplied power from an outlet on the rack, please  
make sure that the rack does not overload the supply  
circuit.  
2. Providing protective earth  
When this product is installed in a rack and is  
supplied power from an outlet on the rack, please  
confirm that the outlet is provided with a suitable  
protective earth connection.  
3. Internal air ambient temperature of the rack  
When this product is installed in a rack, please make  
sure that the internal air ambient temperature of the  
rack is within the specified limit of this product.  
4. Prevention against achieving hazardous  
condition due to uneven mechanical loading  
When this product is installed in a rack, please make  
sure that the rack does not achieve hazardous  
condition due to uneven mechanical loading.  
5. Install the equipment while taking the operating  
temperature of the equipment into consideration  
For the operating temperature of the equipment, refer  
to the specifications of the Operation Manual.  
6. When performing the installation, keep the rear of  
the unit 10 cm (4 inches) or more away from walls  
in order to obtain proper exhaust and radiation of  
heat.  
When using a LAN cable:  
For safety,do not connect to the connector for  
peripheral device wiring that might have excessive  
voltage.  
MVS-8000SF  
1 (P)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Manual Structure  
Purpose of this manual .............................................................................................. 3  
Related manuals......................................................................................................... 3  
Contents ..................................................................................................................... 3  
1. Installation  
1-1. Operating Environment ............................................................................... 1-1  
1-2. Power Supply .............................................................................................. 1-1  
1-2-1. Power Specifications .................................................................. 1-1  
1-2-2. Recommended Power Cord........................................................ 1-1  
1-3. Installation Space (External dimensions) .................................................... 1-2  
1-3-1. MVS8000SF-C........................................................................... 1-2  
1-4. Installing the Options .................................................................................. 1-3  
1-4-1. Installing the Plug-in Boards...................................................... 1-3  
1-4-2. Installing the Connector Board .................................................. 1-6  
1-4-3. Installing the HK-PSU04 ........................................................... 1-7  
1-4-4. Upgrade ...................................................................................... 1-7  
1-4-5. Installing the MKS-8420M ........................................................ 1-8  
1-5. Rack Mounting ............................................................................................ 1-9  
1-6. Matching Connectors ................................................................................1-11  
1-7. Input/Output Signals of Connectors .......................................................... 1-12  
1-8. Checks on Completion of Installation .......................................................1-14  
1-8-1. Description of On-board Switches and LEDs ..........................1-14  
1-8-2. Checks on the Switch Setting the Number of  
Power Supply Units.................................................................. 1-57  
1-9. System Connection.................................................................................... 1-58  
2. Service Overview  
2-1. Troubleshooting .......................................................................................... 2-1  
2-2. Periodic Inspection and Maintenance ......................................................... 2-2  
2-2-1. Cleaning ..................................................................................... 2-2  
2-3. About the Data Backup Capacitor............................................................... 2-2  
MVS-8000SF  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Manual Structure  
Purpose of this manual  
This manual is the installation manual of Switcher Processor Pack MVS8000SF-C  
and their optional boards and units.  
This manual is intended for use by trained system and service engineers, and  
describes the information on installing the MVS8000SF-C.  
Related manuals  
The following manuals are prepared for MVS8000SF-C and their optional boards  
and units.  
. Operation Manual (Supplied with MVS8000SF-C)  
This manual describes the application and operation of MVS8000SF-C.  
. System Setup Manual (Available on request)  
This manual describes the information that is required to connect the MVS-8xxx/  
MVE-8000/DCU-8000/CCP-8000 to the MVS-8000 system, and to start up the  
system.  
If this manual is required, please contact your local Sony Sales Office/Service  
Center.  
. Maintenance Manual (Available on request)  
This manual describes the detailed service information.  
If this manual is required, please contact your local Sony Sales Office/Service  
Center.  
Contents  
This manual is organized by following sections.  
Section 1 Installation  
This section describes the operating environment, power supply, installation space,  
installation of optional boards and units, rack mounting, connectors, input and  
output signals of connectors, checking upon completion of installation, and system  
configuration.  
Section 2 Service Overview  
This section describes the troubleshooting and periodic inspection and maintenance.  
MVS-8000SF  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section 1  
Installation  
1-1. Operating Environment  
m
. As the inrush current at turn-on is a maximum 60 A (at  
100 V)/110 A (at 230 V), the capacity of the AC power  
source must be commensurate with this load.  
If the capacity of the AC power is not adequately large,  
the AC power source braker will operate or the unit will  
abnormally operate.  
. This system contains the two power supply units as the  
standard configuration. A fourth, redundant, power  
supply may be installed as an option.  
Operating guaranteed temperature : +5 dC to +40 dC  
Performance guaranteed temperature : +10 dC to +35 dC  
Operating humidity :  
10 % to 90 %  
(relative humidity)  
_20 dC to +60 dC  
Approx. 45 kg  
(when all options  
are installed)  
Storage temperature :  
Mass :  
When starting up this system, be sure to turn on the  
power of all the power supply units.  
Prohibited locations for installation  
. Areas where the unit will be exposed do direct sunlight  
or any other strong lights.  
1-2-2. Recommended Power Cord  
. Dusty areas  
. Areas subject to vibration.  
w
. Areas with strong electric or magnetic fields.  
. Areas near heat sources.  
. Areas subject to electrical noise.  
. Areas subject where is subjected to static electricity.  
. The power cord is not supplied with the MVS8000SF-C.  
Be sure to use the power cord that is applicable to places  
in the area.  
To avoid a fire or an electric shock, be sure to use the  
designated power cord.  
Ventilation  
. Do not damage the power cord otherwise a fire or  
electric shock may result.  
The inside of the MVS8000SF-C is cooled by a fan (on  
both sides).  
For customers in the U.S.A. and Canada  
1 Power cord, 125 V 10 A (2.4 m) : ! 1-557-377-11  
The power supply can be damaged if the exhaust vent (on  
both sides) and air intake (front panel) are blocked or the  
fan is stopped.  
AC inlet  
1
Therefore, leave a blank space of more than 10 cm in the  
front and back of the MVS8000SF-C.  
1-2. Power Supply  
For customers in the all European countries  
1 Power cord, 250 V 10 A (2.4 m) : ! 1-782-929-21  
1-2-1. Power Specifications  
AC inlet  
1
A switching regulator is used for the power supply of this  
unit. The voltage within the range of 100 V to 240 V can  
be used without changing the supply voltage.  
Power requirements : AC 100 to 240 V 10 %  
Power frequency :  
50/60 Hz  
Current consumption : 100 V : 10 A, 240 V : 4.2 A  
(with all options installed)  
MVS-8000SF  
1-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-3. Installation Space (External dimensions)  
1-3. Installation Space (External dimensions)  
1-3-1. MVS8000SF-C  
482  
465  
440  
375  
144.5  
115.5  
370  
115.5  
35  
61  
Unit : mm  
MVS-8000SF  
1-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-4. Installing the Options  
1-4. Installing the Options  
Model name  
Board Structure  
Plug-in board Connector board  
The MVS8000SF-C is shipped from the factory with the  
necessary option boards (refer to the following table)  
already installed in accordance with the specified system  
configuration.  
MKS-8440M  
Frame Memory Board Set  
DIO-74 board  
MY-102 board  
DI-43 board  
_
_
_
_
_
MKS-8210K1  
1 M/E Upgrade Kit  
The following options are available for the MVS-8000SF.  
DO-44 board  
DIO-74 board  
MKS-8440K1  
Frame Memory Upgrade Kit  
MVS-8000SF Option List  
HK-PSU04  
Power Supply Unit  
_
_
Model name  
Board Structure  
Plug-in board Connector board  
1-4-1. Installing the Plug-in Boards  
MKS-8110HD  
17 Input Board  
_
_
_
CNI-9 board  
CNI-10 board  
CNI-22 board  
Each plug-in board of the Multi Format Switcher MVS-  
8000SF is allocated to a specific slot into which they must  
be installed. Check to see that the respective plug-in boards  
are installed in their respective slots.  
MKS-8110SD  
17 Input Board  
MKS-8110M  
17 Input Board  
MKS-8160HD  
8 Output Board  
OUT-23 board CNO-11 board  
OUT-24 board CNO-17B board  
OUT-27 board CNO-23 board  
The name of the board is shown near the eject lever at the  
right-most end of each plug-in board.  
The respective slot numbers to which plug-in boards that  
are allocated are shown inside the front panel of the MVS-  
8000SF. Install the respective plug-in board according to  
this instruction.  
MKS-8160SD  
8 Output Board  
MKS-8160M  
8 Output Board  
MKS-8170HD  
DME Interface Board  
DIF-119 board  
DIF-122 board  
DIF-141 board  
_
_
_
n
MKS-8170SD  
DME Interface Board  
Check to see that connectors of the plug-in boards are  
securely into the MB-974 board of the MVS-8000SF  
without loose contact.  
MKS-8170M  
DME Interface Board  
If any plug-in board is inserted into the incorrect slot, it  
causes a system error and the system will not work correct-  
ly.  
MKS-8210HD  
Mix/Effect Board Set  
DI-40 board  
_
_
_
_
_
_
_
_
_
_
_
_
_
DO-41 board  
MIX-45 board  
KPC-16 board  
DI-41 board  
c
Be sure to turn off the POWER switch before starting  
installation work.  
If installation work is started with the POWER switch left  
on, it may cause electrical shock or damage to printed  
circuit boards.  
MKS-8210SD  
Mix/Effect Board Set  
DO-42 board  
MIX-45 board  
KPC-16 board  
DI-43 board  
MKS-8210M  
Mix/Effect Board Set  
DO-44 board  
MIX-45 board  
KPC-16 board  
CC-90 board  
MKS-8420M  
Color Corrector Board  
MKS-8440HD  
Frame Memory Board Set  
DIO-62 board  
MY-102 board  
DIO-63 board  
MY-102 board  
_
_
_
_
MKS-8440SD  
Frame Memory Board Set  
MVS-8000SF  
1-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-4. Installing the Options  
Installation Procedure  
4. While the eject levers are opened as shown in the  
illustration, insert the plug-in board into the board  
guide rail.  
1. Turn off the main power of the MVS-8000SF and  
disconnect the AC power cord from the wall outlet.  
2. Loosen the four screws (with drop-safe) and remove  
the front panel to the arrow.  
Screws  
(with drop-safe)  
Front panel  
Screws (with drop-safe)  
3. Remove the six screws and remove the plug-in board  
loose-proof assembly.  
Eject levers  
B3 x 5  
Extract PWB stopper  
assembly  
B3 x 5  
MVS-8000SF  
1-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-4. Installing the Options  
5. While closing the eject levers in the direction of arrow  
Name of option  
Name of board  
Slot on the  
front side  
1, push in the plug-in board.  
MKS-8210HD/SD/M*1 DO-41/DO-42/  
DO-44 board  
3, 8  
MIX-45 board  
KPC-16 board  
4, 9  
5, 10  
6, 11  
DI-40/DI-41/  
DI-43 board  
MKS-8170HD/SD/M  
MKS-8420M  
DIF-119/DIF-122/  
DIF-141 board  
7
CC-90 board  
12  
MKS-8160HD/SD/M*2 OUT-23/OUT-24/  
OUT-27 board  
14 , 15  
MKS-8440HD/SD/M  
DIO-62/DIO-63/  
DIO-74 board  
16  
17  
MY-102 board  
*1 : Note when installing the MKS-8210HD/8210SD/8210M  
The MKS-8210HD/8210SD/8210M must be inserted into the specified  
slot only for M/E. Be sure to insert it into the correct slot without fail.  
The slots into which the MKS-8210HD/8210SD/8210M can be inserted  
are determined in accordance with the configuration of M/Es as shown  
in the following table.  
Slot  
M/E  
SLOT 3 to 6  
M/E 1  
SLOT 8 to 11  
PGM/PST  
*2 : Relation between the slots in which OUT-23/OUT-24/OUT-27 boards  
(MKS-8160HD/8160SD/8160M) are installed and OUTPUT is shown  
below.  
1
1
Slot  
OUTPUT  
Eject lever  
Eject lever  
SLOT 14  
SLOT 15  
1 to 8  
9 to 16  
6. Attach the plug-in board loose-proof assembly and the  
front panel by reversing the installation steps of 2, 3.  
MVS-8000SF  
1-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-4. Installing the Options  
1-4-2. Installing the Connector Board  
2. Insert the connector board horizontally level and  
secure it with the two fixing screws.  
1. Remove the two screws and remove the blank panel.  
n
To install the connector board into the slot in which  
the other board is installed already, loosen the two  
fixing screws and remove the connector board that is  
installed already.  
Fixing screw  
Connector board  
Fixing screw  
B3 x 5  
Blank panel  
Name of option Name of board  
Slot on the rear side  
MKS-8110HD  
MKS-8110SD  
MKS-8110M  
MKS-8160HD  
MKS-8160SD  
MKS-8160 M  
CNI-9 board  
IN 1 to 17  
18 to 34  
B3 x 5  
CNI-10 board  
CNI-22 board  
CNO-11 board  
CNO-17B board  
CNO-23 board  
n
Insert into the slot on the  
rear that corresponds to  
the slot on the front side.  
Store the removed blank panel in a safe place.  
MVS-8000SF  
1-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-4. Installing the Options  
1-4-3. Installing the HK-PSU04  
4. Push the portion of the HK-PSU04 marked by the  
arrow and insert the HK-PSU04 into deep end as far as  
The HK-PSU04 is used after it is installed in the MVS-  
8000SF.  
n
it will go.  
5. Secure the HK-PSU04 with the two screws removed in  
step 3.  
Before installing the HK-PSU04, be sure to turn off the  
main power. If the HK-PSU04 is installed while the main  
power is turned on, it can result in electrical shock or  
damage to printed circuit boards.  
Installation procedure  
1. Remove the front panel of the MVS-8000SF.  
(Refer to Section 1-4-1.)  
HK-PSU04  
2. Remove the two screws (B3 x 5) fixing the power  
supply cover, and remove the power supply cover.  
3. Remove the two screws (PSW3 x 6) fixing the blank  
panel to the location where the HK-PSU04 is going to  
be installed. Then remove the blank panel.  
PSW3 x 6  
PSW3 x 6  
Blank panel  
B3 x 5  
6. Attach the power supply cover and the front panel by  
reversing the installation steps of 1, 2.  
1-4-4. Upgrade  
PSW  
3 x 6  
The MVS-8000 system can be upgraded by the use of the  
following upgrade kit.  
PS cover  
Name of upgrade  
kit  
Name of board  
Slot on the  
front side  
MKS-8210K1  
DO-44 board  
DI-43 board  
DIO-74 board  
3, 8  
6, 11  
16  
B3 x 5  
MKS-8440K1  
n
1. When MKS-8210K1 is used  
Store the removed blank panel in a safe place.  
Exchange the DO-41/42 boards of the M/E unit that  
you want to upgrade, with the DO-44 board of the  
upgrade kit. Also, exchange the DI-40/41 boards that  
you want to upgrade, with the DI-43 board of the  
upgrade kit.  
2. When MKS-8440K1 is used  
Exchange the DIO-62/63 boards in the slot 16 with the  
DIO-74 board of the upgrade kit.  
MVS-8000SF  
1-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-4. Installing the Options  
1-4-5. Installing the MKS-8420M  
c
Be sure to turn off the POWER switch before starting  
MKS-8420M consists of the following boards.  
installation work.  
. CC-90 board :  
. CPU-DK module : 3 pieces  
1 piece  
If installation work is started with the POWER switch left  
on, it may cause electrical shock or damage to printed  
circuit boards.  
CC-90 board installation  
Refer to “1-4-1. Installing the Plug-in Boards”.  
Removal  
1. Remove the OUT-23 board from the MVS-8000SF.  
2. Remove the two screws and washers. Remove the  
bracket (K).  
3. Remove the CPU-DK module from the connector of  
the board.  
CPU-DK module installation  
Replace a CPU-DK module on the following boards with  
each CPU-DK module of MKS-8420M.  
Replacement procedure of the CPU-DK module is de-  
scribed as follows using the OUT-23 board as an example.  
Other boards (DIF-119, DIF-122, DIF-141, OUT-24,  
OUT-27, XPT-21) can also be replaced in the same way.  
4. Peel off the heat conduction sheet 1 (SDI) from the  
removed CPU-DK module.  
n
The heat conduction sheet 1 (SDI) will be reused.  
Front side slot No. Board name (The installed boards are  
different depending on the system  
configuration.)  
Installation  
1. Attach the heat conduction sheet 1 (SDI) that is  
removed in step 4 of removal procedure to the new  
CPU-DK module.  
2. Insert the CPU-DK module connector (PN1) to the  
connector (CN1501) on the OUT-23 board.  
n
7
DIF-119 or DIF-122 or DIF-141(*1)  
XPT-21  
13  
14  
OUT-23 or OUT-24 or OUT-27  
(*1) : MKS-8170HD, MKS-8170SD, MKS-8170M  
Depending on the system configuration, above DME Interface Board  
is not installed in slot 7.  
Confirm that the connector is securely inserted to its  
root.  
3. Install the OUT-23 board by reversing the steps of  
removal.  
B3 x 6  
W3,  
MIDDLE  
Bracket (K)  
Heat conduction  
sheet 1 (SDI)  
CPU-DK  
module  
PN1  
CN1501  
The illustration shows the OUT-23 board.  
MVS-8000SF  
1-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-5. Rack Mounting  
1-5. Rack Mounting  
2. Rack Mounting Procedure  
The MVS-8000SF is mounted in the 19-inch standard rack.  
To mount the MVS-8000SF in the rack, use the specified  
rack mount kit and follow the procedure described below.  
This section describes the rack mounting procedure using  
the RMM-10 rack mount kit.  
n
Specified rack mount kit : RMM-10  
n
Tighten the screws to the following torque.  
Tightening torque : 120 x 10_2 N.m {12.2 kgf.cm}  
If other than the specified rack mount kit is used, the unit  
may not be mounted in the 19-inch standard rack.  
1. Attach the rack tool to the side of the equipment using  
the specified six screws.  
Parts of the RMM-10  
n
. Rack tool  
2 pcs  
1 pc  
1 pc  
Use B4 x 6 screws.  
. Right rack mount adapter  
. Left rack mount adapter  
. Rack tool attaching screw  
(B4 x 6 : 7-682-560-09)  
. Rack tool attaching screw  
(B4 x 10 : 7-682-560-10)  
Rack tool  
B4 x 6  
6 pcs  
6 pcs  
Other required parts  
To mount in the rack, the rack mount kit RMM-10 and the  
following part are required.  
. Screw for rack mounting  
4 pcs  
(B5 x 12 : 7-682-576-04)  
1. Precautions for Rack Mounting  
w
. To prevent the rack from falling or moving, fix the rack  
on a flat and steady floor using bolt or others.  
If the rack falls due to the weight of the equipment, it  
may cause death or injury.  
. Be sure to use the specified rack mount kit.  
If not, injury may result and the equipment may fall due  
to insufficient strength.  
Rack tool  
B4 x 6  
. After rack mounting, be sure to tighten the screws on the  
rack angle and fix the unit in the rack.  
If the screws on the rack angle are not tightened, the unit  
may slip from the rack and fall, causing injury.  
c
When mounting the unit in the rack, note the following:  
. Be sure to mount in the rack with two persons or more.  
. Be careful not to catch your fingers or hands in the rack  
mount rail or others.  
. Mount in the rack in a stable position.  
n
If several units are mounted in a rack, it is recommended to  
install a ventilation fan to prevent temperature rise inside  
the rack.  
MVS-8000SF  
1-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-5. Rack Mounting  
2. Loosen the screws on the rear of the right and left  
adapters and adjust the length of the adapter according  
to the depth of the rack.  
6. Align the groove of the rack tool at the side of the  
equipment with the rail, and slide the equipment to the  
rear.  
(The illustration below shows the left adapter.)  
n
The rack tools are hooked on the rails as shown below.  
Adapter  
Portion of  
the rail  
Rack tool  
Rail  
Rack tool  
Rail  
B4 x 6  
B4 x 6  
n
7. Fix the rack angle in the rack using the specified  
screws.  
Maximum depth of adapter : 750 mm  
Minimum depth of adapter : 595 mm  
3. Attach the right and left adapters to the rack complete-  
ly using the specified six screws.  
(The illustration below shows the left adapter.)  
B5 x 12  
31.75  
8U  
B4 x 10  
4U  
1U  
31.75  
B4 x 10  
Unit : mm  
B5 x 12  
4. Tighten the screws (B4 x 6 : two screws each on the  
right and left) for adjusting the length of the adapter  
completely (the screws that were loosened in step 2).  
5. Remove the front panel of the equipment.  
(Refer to Section 1-4-1.)  
8. Attach the front panel to the equipment.  
(Refer to Section 1-4-1.)  
MVS-8000SF  
1-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-6. Matching Connectors  
1-6. Matching Connectors  
Use the following connectors, cables or equivalents when connecting cables to the unit.  
Model name  
Panel indication  
Connector name  
Matching connector and cable  
Name  
Sony part No.  
MKS-8110SD/HD/M PRIMARY INPUTS  
1 to 17  
BNC, 75 Z  
Belden 8281 coaxial  
cable (SDTV system)  
_
MKS-8160SD/HD/M OUTPUTS 1 to 8  
or  
Belden 1694 coaxial  
cable (HDTV system)  
MVS-8000SF  
REF IN  
BNC, 75 Z  
Belden 8281 coaxial  
cable  
_
REF OUT  
EXT  
REMOTE 1 to 4  
TERMINAL  
D-sub 9-pin, Female  
D-sub 25-pin, Female  
D-sub 9-pin, Male  
Connector 9-pin, Male 1-560-651-00*1  
Junction Shell 9-pin  
1-561-749-00  
GPI  
D-sub 25-pin, Male  
Connector 25-pin, Male 1-560-904-11*1  
Junction Shell 25-pin  
1-563-377-11  
DATA  
RJ-45 modular jack*2  
MDR 68-pin, Female  
_
_
CTRL  
DME 1A, 1B, 2A, 2B  
Dedicated cable  
(supplied with the  
MVE-8000)  
_
*1 : The following crimp contact is required for the plug.  
AWG#18 to #22 : 1-566-493-21  
AWG#22 to #24 : 1-564-774-11  
AWG#24 to #30 : 1-564-775-11  
*2 : Conforms to the IEEE 802.3 Ethernet 100BASE-TX standards.  
MVS-8000SF  
1-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-7. Input/Output Signals of Connectors  
1-7. Input/Output Signals of Connectors  
Pin No.  
Signal Name  
Function  
11  
12  
13  
GPI OUT 6  
General-purpose relay  
output (B) (*4)  
The input/output signals of the connectors at the rear panel  
are as follows.  
GPI OUT 8  
GPI OUT COM  
Ground for open collector  
output  
TERMINAL : RS-232C (D-sub 9-pin, Female)  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
GND  
Ground  
to Terminal  
GPI IN 1  
General-purpose input  
1
5
GPI IN 3  
9
6
GPI IN 5  
_ EXT VIEW _  
GPI IN 7  
GPI OUT 1A  
GPI OUT 2A  
GPI OUT 3A  
GPI OUT 4A  
GPI OUT 5  
GPI OUT 7  
GPI OUT COM  
General-purpose relay  
output (A) (*3)  
Pin No.  
Signal Name  
Function  
1
2
3
4
5
6
7
8
9
DCD  
RXD  
TXD  
DTR  
GND  
DSR  
RTS  
CTS  
_
Data Carrier detect (*1)  
Received data  
Transmitted data  
Data terminal ready (*1)  
Ground  
General-purpose open  
collector output (*4)  
Ground for open collector  
output  
Data set ready (*1)  
Request to send (*2)  
Clear to send (*2)  
_
n
A and B of the same number constitute a pair of relay  
(*1) :Pins 1, 4 and 6 are internally connected together on the CN-2133  
board.  
contacts.  
(*2) :Pins 7 and 8 are internally connected together on the CN-2133 board.  
(*3) <Relay>  
GPI OUT x B  
GPI OUT x A  
GPI : (D-sub 25-pin, Female)  
INPUT x 8, TTL  
x : 1-4  
+V  
OUTPUT x 4, relay contacts 30 V 0.1 A  
(resistive load)  
OUTPUT x 4, open collector, 30 V rated voltage  
(*4)  
<Open collector output>  
GPI OUT 5-8  
GPI OUT COM  
13  
1
14  
25  
EXT VIEW  
Pin No.  
Signal Name  
Function  
1
GND  
Ground  
2
GND  
Ground  
3
GPI IN 2  
General-purpose input  
4
GPI IN 4  
5
GPI IN 6  
6
GPI IN 8  
7
GPI OUT 1B  
GPI OUT 2B  
GPI OUT 3B  
GPI OUT 4B  
General-purpose open  
collector output (B) (*3)  
8
9
10  
MVS-8000SF  
1-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-7. Input/Output Signals of Connectors  
REMOTE 1 to 4 : RS-422A (D-sub 9-pin, Female)  
<DEVICE> (*5) from External Devices  
1
5
9
6
_ EXT VIEW _  
Pin No.  
Signal Name  
Function  
1
2
3
4
5
6
7
8
9
FG  
Frame ground  
TX_  
RX+  
GND  
_
Transmitted data (_)  
Received data (+)  
Common ground  
No Connection  
GND  
TX+  
RX_  
_
Common ground  
Transmitted data (+)  
Received data (_)  
No Connection  
(*5) <DEVICE> : Controlling equipment  
DATA/CTRL : 100BASE-TX, RJ-45 (8-pin)  
8
1
_ EXT VIEW _  
Pin No.  
Signal Name  
Function  
1
2
3
4
5
6
7
8
TX+  
TX_  
RX+  
_
Transmitted data (+)  
Transmitted data (_)  
Received data (+)  
No Connection  
_
No Connection  
RX_  
_
Received data (_)  
No Connection  
_
No Connection  
MVS-8000SF  
1-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
1-8. Checks on Completion of Installation  
1-8-1. Description of On-board Switches and LEDs  
n
The number shown in the parentheses ( ) indicated the address on the circuit board.  
1. CA-44 board (MVS-8000SF)  
A
B
C
D
4
E
E5  
S303  
E2  
TP1002  
TP1003  
TP1001  
1
2
3
5
1
2
3
4
F
E
D
S302  
S301  
SW1  
D1003  
D1002  
D1013  
D901  
D309  
D310  
D601  
D602  
D801  
D802  
SW2  
C CPU-DK  
B Module  
D902  
DI4  
DI1  
D1032  
D1033  
D12  
D18  
D19  
D14  
D15  
D16  
D17  
S102  
S103  
A (COM CPU-1)  
CPU-DR  
Module  
(MAIN CPU)  
1
2
3
4
5
SW2  
F
CN1003  
SW1  
D10  
D13  
E
D
C
B
A
E3  
SW1  
ND101  
ND102  
ND501  
ND502  
ND701  
ND702  
S104  
S502  
S702  
SW2  
DI4  
DI1  
S101  
CPU-DK  
Module  
S501  
S701  
TP1031  
(COM CPU-2)  
D101  
TP101  
D102  
D103  
D104  
TP102  
TP103  
TP104  
B
A
1
2
1
2
3
D1  
TP501  
TP502  
TP503  
TP504  
TP701  
TP702  
TP703  
TP704  
A
D501  
D502  
D503  
D504  
D701  
D702  
D703  
D704  
CN103  
CN503  
CN703  
TP1  
D100  
D101  
D200  
IF-844  
(S-BUS)  
TP2  
5
B
E4  
E1  
E1 S1  
SG-272  
CN1002  
A side/Component side  
<LED>  
D101, D102, D103, D104 (A-4), ND101, ND102 (A-3) :  
MAIN CPU status LED  
Main CPU status indication.  
D601 (A-2) : COM1 ACT status LED  
COM CPU-1 Ethernet communication status indication.  
Lit while data send or receive is in progress.  
D309 (A-2) : RESET status LED  
System reset status indication.  
Lit when S301 is pressed or the power voltage drops to  
+3.3 V.  
D602 (A-2) : COM1 100 status LED  
COM CPU-1 Ethernet communication speed status  
indication.  
Lit :  
100 Mb/s  
Not lit : 10 Mb/s  
D310 (A-2) : CPU RESET status LED  
CA-44 board reset status indication.  
Lit when S302 is pressed or the power voltage drops to  
+3.3 V.  
D701, D702 (A-4), D703, D704 (A-5) : COM CPU-2  
status LED  
COM CPU-2 status indication.  
D501 (A-4), D502, D503, D504 (A-5) : COM CPU-1  
status LED  
COM CPU-1 status indication.  
D801 (A-2) : COM2 ACT status LED  
COM CPU-2 Ethernet communication status indication.  
Lit while data send or receive is in progress.  
MVS-8000SF  
1-14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
D802 (A-2) : COM2 100 status LED  
COM CPU-2 Ethernet communication speed status  
indication.  
S102 (A-2) : Group ID setting switch for LAN  
Sets the group ID for connecting LAN.  
For details, refer to System Setup Manual.  
Lit :  
100 Mb/s  
Not lit : 10 Mb/s  
S103 (A-2) : Unit ID setting switch for LAN  
Sets the unit ID for connecting LAN.  
D901 (A-2) : REF EXT status LED  
REF IN signal presence/absence status indication.  
Lit when the REF signal is input to the REF IN connector.  
Not lit when the REF signal is not input to the REF IN  
connector.  
For details, refer to System Setup Manual.  
S104 (A-4) : Monitor reset switch for the main  
CPU  
Pressing this switch resets the system while maintaining  
this unit through the main CPU control terminal connector.  
D902 (A-2) : PLL LOCK status LED  
REF IN signal format status indication.  
Lit when the REF IN signal matches with the switcher  
format setup.  
S301 (A-1) : System reset switch  
Pressing this switch activates the system reset and the  
system re-starts.  
D1002 (A-2) : +3.3 V  
S302 (A-1) : CA-CPU reset switch  
+3.3 V power supply status indication.  
Lit when the +3.3 V power is supplied.  
Pressing this switch resets the CA-44 board.  
S303 (B-1) : Switch setting the number of the  
power supply units  
D1003 (A-1) : +12 V  
+12 V power supply status indication.  
Lit when the +12 V power is supplied.  
If this LED does not light, the fuse may have blown.  
Sets the number of the power supply units that are required  
for this unit.  
Default setup when shipped from the factory is bits 1, 2 and  
4 : OFF, and bits 3 : ON.  
D1013 (A-2) : +5 V  
+5 V power supply status indication.  
Lit when the +5 V power is supplied.  
S501 (A-4) : Modes setting switch for the COM CPU-1  
Sets the modes of the COM CPU-1.  
Default setting when shipped from the factory is all OFF.  
D1032 (A-2) : SBUS TX status LED  
S-BUS send status indication.  
Lit while the data send is in progress.  
S502 (A-4) : Monitor reset switch for the COM CPU-1  
Pressing this switch resets the system while maintaining  
this unit through the COM CPU-1 control terminal.  
D1033 (A-2) : SBUS RX status LED  
S-BUS receive status indication.  
Lit while the data receive is in progress.  
S701 (A-4) : Modes setting switch for the COM  
CPU-2  
Default setting when shipped from the factory is all OFF.  
ND501, ND502 (A-4) : COM CPU-1 status LED  
COM CPU-1 status indication.  
S702 (A-4) : Monitor reset switch for the COM CPU-2  
Pressing this switch resets the system while maintaining  
this unit through the COM CPU-2 control terminal.  
ND701, ND702 (A-4) : COM CPU-2 status LED  
COM CPU-2 status indication.  
<Connector>  
<Switch>  
CN103 (A-4) : TERMINAL pin  
This pin is connected to the main CPU control terminal  
and used during maintenance.  
Conforms to RS-232C.  
S101 (A-3) : Mode setting switch for the main CPU  
Sets the modes of the main CPU.  
Default setting when shipped from the factory is all OFF.  
MVS-8000SF  
1-15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
CN503 (A-5) : TERMINAL pin  
This pin is connected to the COM CPU-1 control terminal  
and used during maintenance.  
<LED on the CPU DR module> : Main CPU  
D10 (green) (A-1) : RUN status LED  
RUN status indication.  
Conforms to RS-232C.  
Lit when the CPU-DR module starts operating.  
CN703 (A-5) : TERMINAL pin  
This pin is connected to the COM CPU-2 control terminal  
and used during maintenance.  
D12 (green) (A-4) : CD (Card Detect) status LED  
Lit when the CPU-DR module is inserted correctly into the  
parent board.  
Conforms to RS-232C.  
D13 (green) (A-1) : +2.5 V  
CN1003 (A-3) : ISP common connector  
Used only for production in the assembly factory. Used for  
program writing into the JTAG device with ISP.  
Indicates the statue of the +2.5 V power that is generated  
by the VCC (CORE) and supplied to the CPU-DR module.  
Lit while the specified power is turned on.  
CN1002 (A-5) : TERMINAL pin  
This pin is connected to the S-BUS CPU control terminal  
and used during maintenance.  
D14, D15, D16, D17 (A-3) (green) : STATUS1 to  
STATUS4 status LED  
Used for maintenance purpose. Only the STATUS1 LED is  
lit in normal operation.  
Conforms to RS-232C.  
<TEST terminal>  
D18 (green) (A-4) : +3.3 V  
E1 (E-5), E2 (E-1), E3 (C-3), E4 (A-5), E5 (A-1) :  
GND terminal  
Indicates the statue of the VCC (I/O) power that is sup-  
plied to the CPU-DR module.  
Use this terminal as the earth point for measuring the  
respective check terminals.  
Lit while the specified power is turned on.  
D19 (green) (A-4) : CORE status LED  
Indicates the statue of the VCC (CORE) power that is  
supplied to the CPU-DR module.  
TP101, TP102, TP103, TP104 (A-4) : Main CPU  
status check terminal  
Main CPU status check terminal.  
Lit while the specified power is turned on.  
TP501 (A-4), TP502, TP503, TP504 (A-5) : COM  
CPU-1 status check terminal  
<Switch on the CPU DR module> : Main CPU  
SW1 (A-1) : RESET switch  
COM CPU-1 status check terminal.  
Pressing this switch resets the CPU-DR module.  
n
TP701, TP702, TP703, TP704 (A-5) : COM CPU-2  
status check terminal  
In some machines in which the CPU-DR module is  
installed, the system reset may be activated.  
COM CPU-2 status check terminal.  
SW2 (A-2) : MODE switch  
TP1001 (A-1) : +3.3 V check terminal  
8-pin DIP switch  
+3.3 V measuring terminal.  
Used only for production in the assembly factory. All  
switches are set to OFF for normal operation.  
TP1002 (A-1) : +12 V check terminal  
+12 V measuring terminal.  
<LED on the CPU DK module> : COM CPU-1  
: COM CPU-2  
TP1003 (A-1) : +5 V check terminal  
+5 V measuring terminal.  
DI1 (green) (B-5) : CD (Card Detect) status LED  
Lit when the CPU-DK module is inserted correctly to the  
parent board.  
TP1031 (D-4) : SBUS RX check terminal  
S-BUS communication line measuring terminal.  
DI2 (green) (F-3) : RUN status LED  
Lit when the CPU-DK module starts operating.  
MVS-8000SF  
1-16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
DI3 (F-3), DI6 (F-3), DI7 (F-3), DI8 (F-4) (green) :  
STATUS1 to STATUS4 LED  
<LED on the SG-272 board>  
D100 (B-1) : REF OK status LED  
Used for maintenance purpose. Only the STATUS1 LED is  
lit in normal operation.  
Lit while V sync of the reference input is detected.  
D101 (B-1) : REF EXT status LED  
DI4 (green) (B-5) : +3.3 V  
Lit while sync signal is input to the reference input.  
Indicates the status of the VCC (CORE) and VCC (I/O)  
powers that are supplied to the CPU-DK module.  
D200 (B-1) : LOCK status LED  
Lit while the machine is locked to the reference signal.  
<Switch on the CPU DK module> : COM CPU-1  
: COM CPU-2  
SW1 (D-5) : RESET switch  
Pressing this switch resets the CPU-DK module.  
n
In some machines in which the CPU-DK module is  
installed, the system reset may be activated.  
SW2 (C-5) : MODE switch  
8-pin DIP switch  
Used only for production in the assembly factory. All  
switches are set to OFF for normal operation.  
Default setting when shipped from the factory is all OFF.  
<LED on the IF-844 board> : S-BUS  
D1 (B-1) : SBUS RX status LED  
Lit when receiving data.  
<Switch on the IF-844 board> : S-BUS  
S1 (B-3) : RESET switch  
Pressing this switch resets the IF-844 board.  
<TEST terminal on the IF-844 board>  
E1 (B-3) : GND terminal  
Use this terminal as the earth point for measuring the  
respective check terminals.  
TP1 (A-2) : RX check terminal  
S-BUS communication line measuring terminal.  
TP2 (A-3) : TEST terminal  
Terminal for testing.  
MVS-8000SF  
1-17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
2. DO-41 board (MKS-8210HD)/DO-42 board (MKS-8210SD)/DO-44 board (MKS-8210M)  
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
TP6001  
TP6002  
TP4501  
TP4502  
TP4001  
TP4002  
3
4
5
6
7
8
D1  
TP2  
D5  
TP10  
D6  
TP1  
D7  
TP3  
E2  
TP6000  
TP4  
TP4500  
TP4000  
D9  
D8  
E3  
E1  
CN1  
S1  
E8  
TP1000  
TP1500  
TP2000  
TP2500  
TP3000  
TP3500  
9
E5  
TP3002  
TP3001  
E4  
TP1502  
TP1501  
E7  
TP1002  
TP1001  
TP2002  
TP2001  
TP3502  
TP3501  
TP2502  
TP2501  
10  
11  
12  
13  
E6  
TP5  
DO-41 board A side/Component side  
MVS-8000SF  
1-18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
E6  
TP4002  
TP6002  
TP6001  
TP4001  
3
4
5
6
7
8
9
D1  
TP2  
D6  
TP1  
D7  
TP3  
E2  
E1  
TP6000  
TP4500  
TP4000  
D9  
D8  
TP4  
E3  
CN1  
S1  
E5  
E4  
TP1500  
TP1000  
TP1001  
TP2000  
TP2500  
TP3000  
TP3500  
E7  
TP1502  
TP2002  
TP3502  
TP3501  
TP1002  
TP2502  
TP2501  
TP3002  
TP1501  
TP2001  
TP3001  
10  
11  
12  
13  
TP5  
DO-42 board A side/Component side  
. DO-41/42 board  
<LED>  
D1 (A-3) : +12 V  
+12 V power supply status indication.  
Lit when the +12 V power is supplied.  
D8 (A-6) : CONF2 status LED  
D10 to L10 FPGA (Spartan II) CONFIG DONE status  
indication.  
If this LED does not light, the fuse may have blown.  
Not lit when configuration is completed.  
D5 (A-4) : +5 V (DO-41 board)  
+5 V power supply status indication.  
Lit when the +5 V power is supplied.  
D9 (A-5) : CONF1 status LED  
H2 to L2 FPGA (Spartan II) CONFIG DONE status  
indication.  
Not lit when configuration is completed.  
D6 (A-4) : +3.3 V  
+3.3 V power supply status indication.  
Lit when the +3.3 V power is supplied.  
<Switch>  
S1 (A-8) : Reset switch  
Pressing this switch initializes the DO-41/42 board.  
D7 (A-5) : +2.5 V  
+2.5 V power supply status indication.  
Lit when the +2.5 V power is supplied.  
<Connector>  
CN1 (A-6) : ISP common connector  
Used only for production in the assembly factory. Used for  
program writing into the JTAG device with ISP.  
MVS-8000SF  
1-19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
<TEST terminal>  
TP1000 (E-9), TP1500 (F-9), TP2000 (G-9), TP2500  
(J-9), TP3000 (K-9), TP3500 (M-9), TP4000 (K-4),  
TP4500 (J-4), TP6000 (H-4) : PLL LOCK signal  
check terminal (DO-41 board)  
E1 (F-6), E2 (J-4), E3 (L-6), E4 (E-9), E5 (J-9), E-6 (M-12),  
E-7 (N-9), E-8 (A-9) : GND terminal (DO-41 board)  
Use this terminal as the earth point for measuring the  
respective check terminals.  
PLL-LOCK signal measuring terminal.  
E1 (M-4), E2 (G-4), E3 (L-6), E4 (E-8), E5 (G-8), E6 (A-2),  
E7 (N-9) : GND terminal (DO-42 board)  
Use this terminal as the earth point for measuring the  
respective check terminals.  
TP1001 (C-10), TP1501 (E-10), TP2001 (F-10),  
TP2501 (H-10), TP3001 (J-10), TP3501 (K-10),  
TP4001 (M-3), TP4501 (K-3), TP6001 (J-3) : EAV_C  
signal check terminal (DO-41 board)  
EAV_C signal measuring terminal.  
TP1 (A-4) : +3.3 V check terminal  
+3.3 V measuring terminal.  
TP1001 (D-10), TP1501 (F-10), TP2001 (G-10),  
TP2501 (H-10), TP3001 (K-9), TP3501 (L-9), TP4001 (L-3),  
TP4501 (J-3), TP6001 (H-3) : EAV_C signal check  
terminal (DO-42 board)  
TP2 (A-4) : +12 V check terminal  
+12 V measuring terminal.  
EAV_C signal measuring terminal.  
TP3 (A-5) : +2.5 V check terminal  
+2.5 V measuring terminal.  
TP1002 (C-9), TP1502 (E-9), TP2002 (F-9), TP2502 (H-9),  
TP3002 (J-9), TP3502 (K-9), TP4002 (M-3), TP4502 (K-3),  
TP6002 (J-3) : EAV_Y signal check terminal (DO-  
41 board)  
TP4 (H-6), TP5 (H-13) : CK (clock for video signal)  
signal check terminal  
Used when checking the clock for video signal.  
EAV_Y signal measuring terminal.  
TP6 (L-13) : VD (vertical sync) signal check  
terminal  
Used when checking the VD signal supplied from the  
mother board.  
TP1002 (D-10), TP1502 (F-10), TP2002 (G-10),  
TP2502 (J-10), TP3002 (K-9), TP3502 (L-9), TP4002 (L-3),  
TP4501 (J-3), TP6002 (H-3) : EAV_Y signal check  
terminal (DO-42 board)  
EAV_Y signal measuring terminal.  
TP7 (L-13) : CKX (control timing) signal check  
terminal  
Used when checking the CKX signal supplied from the  
mother board.  
TP1000 (D-8), TP1500 (E-8), TP2000 (F-8), TP2500 (H-8),  
TP3000 (J-8), TP3500 (L-8), TP4000 (L-4), TP4500 (K-4),  
TP6000 (H-4) : VCO-FRQ signal check terminal  
VCO-FRQ signal measuring terminal.  
TP8 (M-13) : HD (horizontal sync) signal check  
terminal  
Used when checking the HD signal supplied from the  
mother board.  
TP9 (M-13) : FLOE (field odd even) signal check  
terminal  
Used when checking the FLOE signal supplied from the  
mother board.  
TP10 (A-4) : +5 V check terminal (DO-41 board)  
+5 V measuring terminal.  
MVS-8000SF  
1-20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
D1  
3
TP1  
D9504  
TP9501  
D9004  
TP9001  
D5  
E2  
4
E8  
5
E1  
TP4  
E3  
6
7
S2  
E4  
E5  
8
CN1  
S1  
9
E7  
10  
11  
12  
13  
E6  
TP5  
TP8  
TP9  
DO-44 board A side/Component side  
. DO-44 board  
<LED>  
<Switch>  
D1 (A-3) : +12 V  
S1 (A-9) : Reset switch  
+12 V power supply status indication.  
Pressing this switch initializes the DO-44 board.  
Lit when the +12 V power is supplied.  
If this LED does not light, the fuse may have blown.  
S2 (A-8) : JTAG switch  
Used only for production in the assembly factory. Set this  
switch to ON only when writing program in the JTAG  
device with ISP.  
D5 (A-4) : CONF ERR status LED  
FPGA (EP20K100E) CONFIG DONE status indication.  
Not lit when all configurations are completed.  
<Connector>  
D9004 (A-4) : +1.8 V  
+1.8 V power supply status indication.  
Lit when the +1.8 V power is supplied.  
CN1 (A-8) : ISP common connector  
Used only for production in the assembly factory. Used for  
program writing into the JTAG device with ISP.  
D9504 (A-3) : +3.3 V  
<TEST terminal>  
+3.3 V power supply status indication.  
Lit when the +3.3 V power is supplied.  
E1 (G-6), E2 (G-4), E3 (L-6), E4 (D-8), E5 (J-8), E-6 (M-12),  
E-7 (N-9), E-8 (A-5) : GND terminal  
Use this terminal as the earth point for measuring the  
respective check terminals.  
MVS-8000SF  
1-21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
TP1 (A-3) : +12 V check terminal  
+12 V measuring terminal.  
TP4 (H-6), TP5 (H-13), TP9 (N-13) : CK (clock for  
video signal) signal check terminal  
Used when checking the clock for video signal.  
TP8 (M-13) : HD (horizontal sync) signal check  
terminal  
Used when checking the HD signal supplied from the  
mother board.  
TP9001 (A-4) : +1.8 V check terminal  
+1.8 V measuring terminal.  
TP9501 (A-4) : +3.3 V check terminal  
+3.3 V measuring terminal.  
MVS-8000SF  
1-22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
3. MIX-45 board (MKS-8210HD/SD/M)  
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
3
S1701  
D3704  
4
TP3700  
D3702  
TP3723  
D3701  
TP3717  
D3700  
5
TP3702  
TP3605  
TP3610  
6
TP3606  
TP3611  
7
E3719  
CN1703  
TP1702  
TP1801  
D2203  
D2204  
D2205  
8
S1702  
9
D1  
D12  
D2  
D2201  
D2202  
D2206  
D18  
D19  
D14  
D15  
D16  
D17  
10  
11  
12  
13  
CPU-DR  
Module  
SW2  
SW1  
D10  
D13  
TP3607  
TP3604  
TP3602  
TP3603  
TP3601  
A side/Component side  
<LED>  
D1 (A-9) : MIXER (Y) status LED  
MIXER (Y) CONFIG DONE status indication.  
Not lit when configuration is completed.  
D2202 (A-10) : TBC-B system status LED  
TBC-B system CONFIG DONE status indication.  
Not lit when configuration is completed.  
D2 (A-9) : MIXER (C) status LED  
D2203, D2204, D2205 (A-8) : MIX-CPU status LED  
MIXER (C) CONFIG DONE status indication.  
Not lit when configuration is completed.  
Indicates the CPU status on the MIX board.  
D2206 (A-10) : P-XPT status LED  
PXPT CONFIG DONE status indication.  
Not lit when configuration is completed.  
D2201 (A-9) : TBC-A system status LED  
TBC-A system CONFIG DONE status indication.  
Not lit when configuration is completed.  
D3700 (A-5) : +1.8 V  
+1.8 V power supply status indication.  
Lit when the +1.8 V power is supplied.  
MVS-8000SF  
1-23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
D3701 (A-5) : +2.5 V  
+2.5 V power supply status indication.  
Lit when the +2.5 V power is supplied.  
TP3603 (N-12) : CKX (control timing) signal check terminal  
Use this terminal to check the CKX signal supplied from  
mother board.  
D3702 (A-4) : +3.3 V  
+3.3 V power supply status indication.  
Lit when the +3.3 V power is supplied.  
TP3604 (N-12) : VD (vertical sync) signal check terminal  
Use this terminal to check the VD signal supplied from  
mother board.  
D3704 (A-4) : +12 V  
TP3605 (N-5) : Buffered VD0 (vertical sync) signal  
check terminal  
Use this terminal to check the VD signal that is used on  
this board.  
+12 V power supply status indication.  
Lit when the +12 V power is supplied.  
If this LED does not light on, the fuse may have blown.  
<Switch>  
TP3606 (P-6) : Buffered CKX0 (switching) signal  
check terminal  
Use this terminal to check the CKX signal that is used in  
this circuit board.  
S1701 (A-4) : MIX-CPU reset switch  
Pressing this switch initializes the CPU on the MIX-45 board.  
S1702 (A-8) : Monitor reset switch  
The reset switch that is used to reset the monitor during  
maintenance through the terminal.  
TP3607 (N-12) : CK (clock for video) signal check  
terminal  
Use this terminal to check the clock for video signal that is  
used in this circuit board.  
<Connector>  
CN1703 (A-8) : TERMINAL pin  
TERMINAL pin  
This pin is connected to the control terminal and used  
during maintenance.  
TP3610 (N-6) : Buffered HD0 (horizontal sync)  
signal check terminal  
Use this terminal to check the HD signal that is used in this  
circuit board  
Conforms to RS-232C.  
CN2201 (A-6) : ISP common connector  
Used only for production in the assembly factory. Used for  
program writing into the JTAG device with ISP.  
TP3611 (N-7) : Buffered FLOE0 (field odd even)  
signal check terminal  
Use this terminal to check the FLOE signal that is used in  
this circuit board.  
<TEST terminal>  
E3719 (A-7) : GND terminal  
Use this terminal as the earth point for measuring the  
respective check terminals.  
TP3700 (A-4) : +12 V check terminal  
+12 V measuring terminal.  
TP3702 (A-5) : +1.8 V check terminal  
TP1702 (B-8) : CPU CK (CPU clock) signal check terminal  
+1.8 V measuring terminal.  
Use this terminal to check the CPU clock for video signal.  
TP3717 (A-5) : +2.5 V check terminal  
TP1801 (K-7) : DLY_WE terminal  
Use this terminal to check the Write_Enable signal of the  
delay circuit.  
+2.5 V measuring terminal.  
TP3723 (A-4) : +3.3 V check terminal  
+3.3 V measuring terminal.  
TP3601 (N-13) : FLOE (field odd even) signal  
check terminal  
Use this terminal to check the FLOE signal from the  
mother board.  
<LED on the CPU DR module> (C11)  
Refer to < LED on the CPU DR module > in 1. CA-44  
board.  
<Switch on the CPU DR module> (C11)  
Refer to < Switch on the CPU DR module > in 1. CA-44  
board.  
TP3602 (N-13) : HD (horizontal sync) signal check terminal  
Use this terminal to check the HD signal supplied from  
mother board.  
MVS-8000SF  
1-24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
4. KPC-16 board (MKS-8210HD/SD/M)  
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
E6064  
1
2
TP6067  
TP6060  
3
TP6061  
4
E6066  
E6069  
TP6068  
D6001  
D6065  
D6060  
D6062  
D6063  
D6061  
5
6
CN6000  
E6063  
7
TP6000  
8
D6108  
D6107  
D6106  
D6105  
D6104  
D6103  
D6102  
D6101  
D6100  
D6109  
9
E6065  
10  
11  
12  
13  
TP6801  
TP6802  
E6062  
TP6104  
TP6103  
TP6102  
TP6101  
TP6800  
A side/Component side  
<LED>  
D6001 (A-5) : RESET status LED  
System reset status indication.  
D6100 (A-10) : COMMON WASH FPGA CONFIG  
DONE status LED  
Lit when the +3.3 V power decreases.  
COMMON WASH FPGA CONFIG DONE status indica-  
tion.  
D6060 (A-5) : +3.3 V  
Not lit when configuration is completed.  
+3.3 V power supply status indication.  
Lit when the +3.3 V power is supplied.  
D6101 (A-10) : WASH4 FPGA CONFIG DONE  
status LED  
D6061 (A-6), D6062 (A-5), D6063 (A-5) : +1.8 V  
+1.8 V power supply status indication.  
WASH4 FPGA CONFIG DONE status indication.  
Not lit when configuration is completed.  
Lit when the +1.8 V power is supplied.  
D6102 (A-10) : WASH3 FPGA CONFIG DONE  
status LED  
D6065 (A-5) : +12 V  
+12 V power supply status indication.  
Lit when the +12 V power is supplied.  
If this LED does not light, the fuse may have blown.  
WASH3 FPGA CONFIG DONE status indication.  
Not lit when configuration is completed.  
MVS-8000SF  
1-25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
D6103 (A-10) : WASH2 FPGA CONFIG DONE  
status LED  
TP6060 (A-2) : +3.3 V check terminal  
+3.3 V measuring terminal.  
WASH2 FPGA CONFIG DONE status indication.  
Not lit when configuration is completed.  
TP6061 (A-4), TP6067 (G-1), TP6068 (F-4) : +1.8 V  
check terminal  
D6104 (A-9) : WASH1 FPGA CONFIG DONE status  
LED  
+1.8 V measuring terminal.  
WASH1 FPGA CONFIG DONE status indication.  
Not lit when configuration is completed.  
TP6101 (N-13) : VD (vertical sync) signal check  
terminal  
Used to check the VD signal supplied from the mother  
board.  
D6105 (A-9) : KEYER4 FPGA CONFIG DONE  
status LED  
KEYER4 FPGA CONFIG DONE status indication.  
Not lit when configuration is completed.  
TP6102 (N-13) : CKX (control timing) signal check  
terminal  
Used to check the CKX signal supplied from the mother  
board.  
D6106 (A-9) : KEYER3 FPGA CONFIG DONE  
status LED  
KEYER3 FPGA CONFIG DONE status indication.  
Not lit when configuration is completed.  
TP6103 (N-13) : HD (horizontal sync) signal check  
terminal  
Used to check the HD signal supplied from the mother  
board.  
D6107 (A-9) : KEYER2 FPGA CONFIG DONE  
status LED  
KEYER2 FPGA CONFIG DONE status indication.  
Not lit when configuration is completed.  
TP6104 (N-12) : FLOE (field odd even) signal  
check terminal  
Used to check the FLOE signal supplied from the mother  
board.  
D6108 (A-9) : KEYER1 FPGA CONFIG DONE  
status LED  
KEYER1 FPGA CONFIG DONE status indication.  
Not lit when configuration is completed.  
TP6800 (N-13) : HALF VIDEO CLOCK signal check  
terminal  
Used to check the HALF VIDEO CLOCK signal.  
D6109 (A-10) : WKG FPGA CONFIG DONE status  
LED  
WKG FPGA CONFIG DONE status indication.  
Not lit when configuration is completed.  
TP6801 (N-10) : VCLK (clock for video signal)  
signal check terminal  
Used to check the clock for video signal  
<Connector>  
TP6802 (A-11) : DLY_WE terminal  
CN6000 (A-6) : ISP common connector  
Used only for production in the assembly factory. Used for  
program writing into the JTAG device with ISP.  
Used to check the Write-Enable signal of the delay circuit.  
<TEST terminal>  
E6062 (N-12), E6063 (N-7), E6064 (N-1), E6065 (K-  
10), E6066 (K-4), E6069 (E-4), : GND terminal  
Use this terminal as the earth point for measuring the  
respective check terminals.  
TP6000 (P-8) : SYS_CLK signal check terminal  
Used for checking the SYSTEM CLOCK signal.  
MVS-8000SF  
1-26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
5. DI-40 board (MKS-8210HD)/DI-41 board (MKS-8210SD)/DI-43 board (MKS-8210M)  
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
TP5507  
TP5506  
TP5502  
TP5505  
TP5504  
TP5501  
3
4
5
6
7
8
9
D1  
TP3  
D2  
TP1  
D3  
TP2  
TP3007  
TP3006  
TP3002  
TP3005  
TP3004  
TP3001  
TP3003  
TP3000  
TP3507  
TP3506  
TP3502  
TP3505  
TP3504  
TP3501  
TP3503  
TP3500  
TP8007  
TP8006  
TP8002  
TP8005  
TP8004  
TP8001  
TP8003  
TP8000  
TP4007  
TP4006  
TP4002  
TP4005  
TP4004  
TP4001  
TP4003  
TP4000  
TP4507  
TP5007  
TP5006  
TP5002  
TP5005  
TP5004  
TP5001  
TP5003  
TP5000  
TP4506  
TP4502  
TP4505  
TP4504  
TP4501  
TP4503  
TP4500  
TP5503  
TP5500  
D5  
D6  
CN1  
S1  
E1  
E7  
TP2000  
TP2003  
TP2001  
TP2004  
TP2005  
TP2002  
TP2500  
TP1000  
TP1003  
TP1001  
TP1004  
TP1005  
TP1002  
TP1006  
TP1007  
TP1500  
TP7000  
TP7500  
TP6500  
TP6503  
TP6501  
TP6504  
TP6505  
TP6502  
TP6506  
TP6507  
TP6000  
TP2503  
TP2501  
TP2504  
TP2505  
TP2502  
TP1503  
TP1501  
TP1504  
TP1505  
TP1502  
TP1506  
TP1507  
TP7003  
TP7001  
TP7004  
TP7005  
TP7002  
TP7006  
TP7007  
TP7503  
TP7501  
TP7504  
TP7505  
TP7502  
TP7506  
TP7507  
TP6003  
TP6001  
TP6004  
TP6005  
TP6002  
E6  
10  
11  
12  
13  
E5  
DI-40 board A side/Component side  
MVS-8000SF  
1-27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
TP3001  
TP3501  
TP4501  
TP5001  
E2  
TP5501  
TP4001  
3
4
5
6
7
8
9
D1  
TP3  
D2  
TP1  
D3  
TP2  
TP3000  
TP3500  
TP4000  
TP4500  
TP5000  
TP5500  
E1  
D5  
D6  
CN1  
S1  
E3  
E6  
TP2000  
TP2500  
TP1000  
TP1500  
TP7001  
TP7000  
TP7500  
TP6501  
TP6500  
TP6000  
10  
TP2501  
TP1001  
E4  
TP1501  
TP7501  
TP6001  
TP2001  
11  
12  
13  
E5  
E7  
DI-41 board A side/Component side  
. DI-40/41 board  
<LED>  
D1 (A-3) : +12 V  
+12 V power supply status indication.  
Lit when the +12 V power is supplied.  
D6 (A-5) : CONF2 status LED  
D10 to L10 FPGA (Spartan II) CONFIG DONE status  
indication.  
If this LED does not light, the fuse may have blown.  
Not lit when configuration is completed.  
D2 (A-4) : +3.3 V  
<Switch>  
+3.3 V power supply status indication.  
Lit when the +3.3 V power is supplied.  
S1 (A-6) : DI reset switch  
Pressing this switch initializes the DI-40 and D-I41 boards.  
D3 (A-4) : +2.5 V  
<Connector>  
+2.5 V power supply status indication.  
Lit when the +2.5 V power is supplied.  
CN1 (A-6) : ISP common connector  
Used only for production in the assembly factory. Used for  
program writing into the JTAG device with ISP.  
D5 (A-5) : CONF1 status LED  
H2 to L2 FPGA (Spartan II) CONFIG DONE status  
indication.  
<TEST terminal>  
E1 (C-6), E2 (J-2), E3 (P-5), E4 (B-11), E5 (H-11), E6 (N-8),  
E7 (A-7) : GND terminal bard  
Not lit when configuration is completed.  
Use this terminal as the earth point for measuring the  
respective check terminals.  
MVS-8000SF  
1-28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
E1 (A-4), E2 (J-2), E3 (F-6), E4 (D-11), E5 (H-11), E6  
(N-8), E7 (L-12) : GND terminal (DI-41 board)  
Use this terminal as the earth point for measuring the  
respective check terminals.  
TP1003 (D-8), TP1503 (E-8), TP2003 (A-8), TP2503 (B-8),  
TP3003 (D-5), TP3503 (E-4), TP4003 (H-5), TP4503 (K-5),  
TP5003 (L-5), TP5503 (N-5), TP6003 (L-8), TP6503 (K-8),  
TP7003 (G-8), TP7503 (H-8), TP8003 (G-4) :  
FRAME signal check terminal (DI-40 board)  
FRAME signal measuring terminal.  
TP1 (A-4) : +3.3 V check terminal  
+3.3 V measuring terminal.  
TP1004 (D-8), TP1504 (E-8), TP2004 (A-8), TP2504 (B-8),  
TP3004 (D-5), TP3504 (E-4), TP4004 (H-5), TP4504 (K-5),  
TP5004 (L-5), TP5504 (N-5), TP6004 (L-8), TP6504 (K-8),  
TP7004 (G-8), TP7504 (H-8), TP8004 (G-4) : CRC  
signal check terminal (DI-40 board)  
TP2 (A-4) : +2.5 V check terminal  
+2.5 V measuring terminal.  
TP3 (A-3) : +12 V check terminal  
+12 V measuring terminal.  
CRC signal measuring terminal.  
TP201 (N-13) : VD (vertical sync) signal check terminal  
VD signal measuring terminal.  
TP1005 (D-8), TP1505 (E-8), TP2005 (A-8), TP2505 (B-8),  
TP3005 (D-5), TP3505 (E-4), TP4005 (H-5), TP4505 (K-5),  
TP5005 (L-5), TP5505 (N-5), TP6005 (L-8), TP6505 (K-8),  
TP7005 (G-8), TP7505 (H-8), TP8005 (G-4) : SIG  
DET signal check terminal (DI-40 board)  
TP202 (N-13) : CKX (control timing) signal check terminal  
CKX signal measuring terminal.  
SIG_DET signal measuring terminal.  
TP203 (P-13) : HD (horizontal sync) signal check terminal  
HD signal measuring terminal.  
TP1006 (D-8), TP1506 (E-8), TP2006 (A-8), TP2506 (B-8),  
TP3006 (D-5), TP3506 (E-4), TP4006 (H-4), TP4506 (K-4),  
TP5006 (L-4), TP5506 (N-4), TP6006 (L-11), TP6506 (K-8),  
TP7006 (G-8), TP7506 (H-8), TP8006 (G-4) : EAV_Y  
signal check terminal (DI-40 board)  
TP204 (P-13) : FLOE (field odd even) signal check  
terminal  
FLOE signal measuring terminal.  
EAV_Y signal measuring terminal.  
TP1000 (D-8), TP1500 (E-8), TP2000 (A-8), TP2500 (B-8),  
TP3000 (D-5), TP3500 (E-4), TP4000 (H-5), TP4500 (K-5),  
TP5000 (L-5), TP5500 (N-5), TP6000 (L-8), TP6500 (K-8),  
TP7000 (G-8), TP7500 (H-8), TP8000 (G-4) : 1R001  
signal check terminal (DI-40 board)  
TP1007 (D-8), TP1507 (E-8), TP2007 (A-8), TP2507 (B-8),  
TP3007 (D-5), TP3507 (E-4), TP4007 (H-4), TP4507 (K-4),  
TP5007 (L-4), TP5507 (N-4), TP6007 (L-11), TP6507 (K-8),  
TP7007 (G-8), TP7507 (H-8), TP8007 (G-4) : EAV_C  
signal check terminal (DI-40 board)  
1R001 signal measuring terminal.  
EAV_C signal measuring terminal.  
TP1001 (D-8), TP1501 (E-8), TP2001 (A-8), TP2501 (B-8),  
TP3001 (D-5), TP3501 (E-4), TP4001 (H-5), TP4501 (K-5),  
TP5001 (L-5), TP5501 (N-5), TP6001 (L-8), TP6501 (K-8),  
TP7001 (G-8), TP7501 (H-8), TP8001 (G-4) : HANC  
signal check terminal (DI-40 board)  
TP1000 (E-9), TP1500 (F-9), TP2000 (B-9), TP2500 (C-9),  
TP3000 (C-4), TP3500 (E-4), TP4000 (H-4), TP4500 (J-4),  
TP5000 (L-4), TP5500 (M-4), TP6000 (M-9), TP6500 (L-9),  
TP7000 (H-9), TP7500 (J-9), TP8000 (F-4) :  
VCO_FRQ signal check terminal (DI-41 board)  
VCO_FRQ signal measuring terminal.  
HANC signal measuring terminal.  
TP1002 (D-8), TP1502 (E-8), TP2002 (A-8), TP2502 (B-8),  
TP3002 (D-5), TP3502 (E-4), TP4002 (H-5), TP4502 (K-5),  
TP5002 (L-5), TP5502 (N-5), TP6002 (L-8), TP6502 (K-8),  
TP7002 (G-8), TP7502 (H-8), TP8002 (G-4) : LINE  
signal check terminal (DI-40 board)  
TP1001 (D-11), TP1501 (E-11), TP2001 (A-11),  
TP2501 (C-11), TP3001 (D-2), TP3501 (F-2), TP4001 (J-2),  
TP4501 (K-2), TP5001 (M-2), TP5501 (N-3), TP6001 (L-11),  
TP6501 (K-11), TP7001 (G-11), TP7501 (H-11),  
TP8000 (F-4) : EAV_Y signal check terminal (DI-41  
board)  
LINE signal measuring terminal.  
EAV_Y signal measuring terminal.  
MVS-8000SF  
1-29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
E2  
D1  
E3  
3
4
5
6
7
8
9
TP1  
D9551  
TP9501  
TP3001  
TP3501  
TP8001  
TP4001  
TP4501  
TP5001  
E1  
D9051  
TP9001  
TP5501  
D401  
E7  
S1  
S101  
CN101  
TP2001  
TP2501  
TP1001  
TP1501  
TP7001  
TP7501  
TP6501  
TP6001  
E6  
10  
11  
12  
13  
DI-43 board A side/Component side  
. DI-43 board  
<LED>  
<Switch>  
D1 (A-3) : +12 V  
S1 (A-7) : DI reset switch  
+12 V power supply status indication.  
Pressing this switch initializes the DI-43 board.  
Lit when the +12 V power is supplied.  
If this LED does not light, the fuse may have blown.  
S101 (A-8) : JTAG switch  
Used only for production in the assembly factory. Set this  
switch to ON only when writing program in the JTAG  
device with ISP.  
D401 (A-6) : CONF ERR status LED  
FPGA (EP20K100E) CONFIG DONE status indication.  
Not lit when all configurations are completed.  
<Connector>  
D9051 (A-5) : +1.8 V  
+1.8 V power supply status indication.  
Lit when the +1.8 V power is supplied.  
CN101 (A-8) : ISP common connector  
Used only for production in the assembly factory. Used for  
program writing into the JTAG device with ISP.  
D9551 (A-4) : +3.3 V  
<TEST terminal>  
+3.3 V power supply status indication.  
Lit when the +3.3 V power is supplied.  
E1 (C-5), E2 (J-2), E3 (N-3), E4 (C-11), E5 (H-11), E6 (N-10),  
E7 (A-6) : GND terminal  
Use this terminal as the earth point for measuring the  
respective check terminals.  
MVS-8000SF  
1-30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
TP1 (A-3) : +12 V check terminal  
+12 V measuring terminal.  
TP501 (P-13) : HD (horizontal sync) signal check terminal  
HD signal measuring terminal.  
TP1001 (D-8), TP1501 (E-8), TP2001 (A-8), TP2501 (C-8),  
TP3001 (D-5), TP3501 (F-5), TP4001 (H-5), TP4501 (K-5),  
TP5001 (L-5), TP5501 (N-5), TP6001 (L-8), TP6501 (K-8),  
TP7001 (G-8), TP7501 (H-8), TP8001 (G-5) : ERR  
check terminal  
SDI signal error measuring terminal.  
TP9001 (A-5) : +1.8 V check terminal  
+1.8 V measuring terminal.  
TP9501 (A-4) : +3.3 V check terminal  
+3.3 V measuring terminal.  
MVS-8000SF  
1-31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
6. DIF-119 board (MKS-8170HD)/DIF-122 board (MKS-8170SD)/DIF-141 board (MKS-8170M)  
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
E3411  
3
4
5
6
7
8
9
E3425  
D3404  
D3402  
D3401  
D3400  
E3429  
E3417  
E3426  
E3412  
TP3309  
S2301  
D2800  
D3100  
D2700  
D2703  
D2702  
D2701  
CN2301  
CN2700  
E3419  
E2300  
E3407  
TP2301  
S2300  
A
B
C
D
E
F
DI1  
10  
11  
12  
13  
DI4  
SW2  
CPU-DK  
Module  
E3408  
TP1500  
SW1  
TP1304  
TP3304  
TP1301  
TP1303  
TP1300  
TP3305  
TP3306  
E3410  
TP3308  
TP1302  
TP1305  
TP3300  
TP3303  
TP3302  
5
4
3
2
1
TP3307  
TP3301  
E3421  
E3427  
E3404  
DIF-119 board A side/Component side  
MVS-8000SF  
1-32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
E3411  
E3414  
3
4
5
6
7
8
9
E3425  
TP3401  
D3404  
TP3402  
D3402  
TP3400  
D3401  
TP3403  
D3400  
TP3310  
E3429  
E3417  
E3426  
E3412  
S2301  
D2800  
D3100  
D2700  
D2703  
D2702  
D2701  
CN2301  
CN2700  
E3419  
E2300  
E3407  
A
B
C
D
E
F
S2300  
DI1  
10  
11  
12  
13  
DI4  
SW2  
CPU-DK  
Module  
E3408  
TP3304  
TP3305  
SW1  
TP1400  
E3410  
TP3308  
TP3306  
TP1500  
5
4
3
2
1
TP1600  
TP3303  
TP3302  
E3421  
TP3307  
E3427  
E3404  
DIF-122 board A side/Component side  
. DIF-119/122 board  
<LED>  
D2700 (B-6) : TBC-1 system status LED  
TBC-1 system CONFIG DONE status indication.  
Not lit when configuration is completed.  
D3401 (A-5) : +2.5 V  
+2.5 V power supply status indication.  
Lit when the +2.5 V power is supplied.  
D2701 (B-7), D2702 (B-6), D2703 (B-6) : MAIN CPU  
status LED  
Main CPU status indication.  
D3402 (A-5) : +3.3 V  
+3.3 V power supply status indication.  
Lit when the +3.3 V power is supplied.  
D2800 (B-6) : XPT status LED  
D3404 (A-4) : +12 V  
XPT CONFIG DONE status indication.  
Not lit when configuration is completed.  
+12 V power supply status indication.  
Lit when the +12 V power is supplied.  
If this LED does not light, the fuse may have blown.  
D3100 (B-6) : TBC-2 system status LED  
TBC-2 system CONFIG DONE status indication.  
Not lit when configuration is completed.  
D3406 (A-5) : +5 V  
+5 V power supply status indication.  
Lit when the +5 V power is supplied.  
D3400 (A-5) : +1.8 V  
+1.8 V power supply status indication.  
Lit when the +1.8 V power is supplied.  
MVS-8000SF  
1-33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
<Switch>  
TP1304 (G-12) : CRC signal check terminal (DIF-  
119 board)  
CRC signal measuring terminal.  
S2300 (A-9) : RESET switch  
Pressing this switch resets the DIF-119 and 122 board.  
S2301 (A-5) : MONITOR reset switch  
The reset switch that is used to reset the monitor in the  
maintenance from the TERMINAL.  
TP1305 (G-12) : SIGDET signal check terminal  
(DIF-119 board)  
SIGDET signal measuring terminal.  
<Connector>  
TP1500 (J-11) : RCLK signal check terminal (DIF-  
119 board)  
RCLK signal measuring terminal.  
CN2301 (A-6) : TERMINAL pin  
This pin is connected to the CPU control terminal and used  
during maintenance. Conforms to RS-232C.  
TP2301 (A-9) : CPU CK (CPU clock) signal check  
terminal (DIF-119 board)  
CN2700 (A-6) : ISP common connector  
Used only for production in the assembly factory. Used for  
program writing into the JTAG device with ISP.  
Used to check the CPU clock.  
TP3300 (L-12) : FLOE (field odd even) signal  
check terminal (DIF-119 board)  
<TEST terminal>  
E2300 (B-8), E3404 (P-13), E3407 (N-8), E3408 (L-11),  
E3410 (E-12), E3411 (P-1), E3412 (N-5), E3417 (K-5),  
E3419 (E-7), E3421 (B-13), E3425 (E-3), E3426 (C-5),  
E3427 (J-13), E3429 (B-5) : GND terminal (DIF-119  
board)  
FLOE signal measuring terminal.  
TP3301 (L-13) : HD (horizontal sync) signal check  
terminal (DIF-119 board)  
HD signal measuring terminal.  
Use this terminal as the earth point for measuring the  
respective check terminals.  
TP3302 (L-13) : CKX (control timing) signal check  
terminal (DIF-119 board)  
E2300 (B-8), E3404 (P-13), E3407 (N-8), E3408 (L-11),  
E3410 (E-12), E3411 (P-1), E3412 (N-5), E3414 (L-2),  
E3417 (K-5), E3419 (E-7), E3421 (B-13), E3425 (E-3),  
E3426 (D-5), E3427 (K-12), E3429 (B-5) : GND  
terminal (DIF-122 board)  
CKX signal measuring terminal.  
TP3303 (M-13) : VD (vertical sync) signal check  
terminal (DIF-119 board)  
VD signal measuring terminal.  
Use this terminal as the earth point for measuring the  
respective check terminals.  
TP3304 (J-12) : VDO signal check terminal (DIF-  
119 board)  
TP1300 (G12) : 1.001 signal check terminal (DIF-  
119 board)  
VDO signal measuring terminal.  
1.001 signal measuring terminal.  
TP3305 (J-12) : HDO signal check terminal (DIF-  
119 board)  
TP1301 (G-12) : HANC signal check terminal (DIF-  
119 board)  
HDO signal measuring terminal.  
HANC signal measuring terminal.  
TP3306 (J-12) : FLOEO signal check terminal (DIF-  
119 board)  
TP1302 (G-12) : LINE signal check terminal (DIF-  
119 board)  
FLOEO signal measuring terminal.  
LINE signal measuring terminal.  
TP3307 (J-12) : CKXO signal check terminal (DIF-  
119 board)  
TP1303 (G-12) : FRAME signal check terminal  
(DIF-119 board)  
CKXO signal measuring terminal.  
FRAME signal measuring terminal.  
MVS-8000SF  
1-34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
TP3308 (L-12) : CK (clock for video signal) signal  
(DIF-119 board)  
TP3401 (A-4) : +12 V check terminal (DIF-122  
board)  
Uses this terminal when checking the clock signal for video.  
+12 V measuring terminal.  
TP3309 (H-5) : CK2 signal check terminal (DIF-119  
board)  
TP3402 (A-4) : +3.3 V check terminal (DIF-122  
board)  
Uses this terminal when checking the clock signal for video.  
+3.3 V measuring terminal.  
TP1300 (F-12), TP1400 (D-12), TP1500 (J-12) ,  
TP1600 (H-12) : VCO_FRQ signal check terminal  
VCO_FRQ signal measuring terminal.  
TP3403 (A-5) : +1.8 V check terminal (DIF-122  
board)  
+1.8 V measuring terminal.  
<LED on the CPU DK module> (C-10)  
Refer to < LED on the CPU DR module > in 1. CA-44  
board.  
TP3302 (M-13) : CKX (control timing) signal check  
terminal (DIF-122 board)  
CKX signal measuring terminal.  
<Switch on the CPU DK module> (C-10)  
Refer to < Switch on the CPU DR module > in 1. CA-44  
board.  
TP3303 (M-13) : VD (vertical sync) signal check  
terminal (DIF-122 board)  
VD signal measuring terminal.  
TP3304 (K-11) : VDO signal check terminal (DIF-  
122 board)  
VDO signal measuring terminal.  
TP3305 (K-11) : HDO signal check terminal (DIF-  
122 board)  
HDO signal measuring terminal.  
TP3306 (K-12) : FLOEO signal check terminal  
(DIF-122 board)  
FLOEO signal measuring terminal.  
TP3307 (K-12) : CKXO signal check terminal (DIF-  
122 board)  
CKXO signal measuring terminal.  
TP3308 (K-12) : CK27 signal check terminal (DIF-  
122 board)  
CK27 signal measuring terminal.  
TP3310 (H-4) : CK1 signal check terminal (DIF-122  
board)  
Used to check the CK1 signal.  
TP3400 (A-5) : +2.5 V check terminal (DIF-122  
board)  
+2.5 V measuring terminal.  
MVS-8000SF  
1-35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
E3411  
E3414  
3
4
5
6
7
8
9
E3425  
TP3700  
D3700  
TP3600  
D3703  
TP3500  
D3702  
TP3400  
D3701  
E3429  
E3417  
E3426  
E3412  
TP3309  
S2301  
CN2301  
D2703  
D2702  
D2701  
CN2700  
D2700  
S2700  
E3419  
E2300  
E3407  
TP2301  
S2300  
A
B
C
D
E
F
DI1  
10  
11  
12  
13  
DI4  
SW2  
CPU-DK  
Module  
E3408  
SW1  
TP1300  
TP3308  
5
4
3
2
1
TP1400  
E3404  
E3421  
TP3300  
TP3303  
E3410  
E3427  
TP3301 TP3302  
DIF-141 board A side/Component side  
. DIF-141 board  
<LED>  
D2700 (A-7) : CONF ERR status LED  
D3702 (A-5) : +2.5 V  
FPGA (EP20K100E and Spartan II) CONFIG DONE  
status indication.  
+2.5 V power supply status indication.  
Lit when the +2.5 V power is supplied.  
Not lit when all configurations are completed.  
D3703 (A-4) : +3.3 V  
D2701 (B-7), D2702 (B-6), D2703 (B-6) : MAIN CPU  
status LED  
+3.3 V power supply status indication.  
Lit when the +3.3 V power is supplied.  
Main CPU status indication.  
<Switch>  
D3700 (A-4) : +12 V  
S2300 (A-9) : RESET switch  
Pressing this switch resets the DIF-141 board.  
+12 V power supply status indication.  
Lit when the +12 V power is supplied.  
If this LED does not light, the fuse may have blown.  
S2301 (A-5) : MONITOR reset switch  
The reset switch that is used to reset the monitor in the  
maintenance from the TERMINAL.  
D3701 (A-5) : +1.8 V  
+1.8 V power supply status indication.  
Lit when the +1.8 V power is supplied.  
MVS-8000SF  
1-36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
S2700 (A-7) : JTAG switch  
TP3309 (H-5) : CK2 signal check terminal  
Used only for production in the assembly factory. Set this  
switch to ON only when writing program in the JTAG  
device with ISP.  
Uses this terminal when checking the clock signal for video.  
TP3310 (G-11) : CK3 signal check terminal  
Uses this terminal when checking the clock signal for video.  
<Connector>  
CN2301 (A-6) : TERMINAL pin  
This pin is connected to the CPU control terminal and used  
during maintenance. Conforms to RS-232C.  
TP3400 (A-5) : +1.8 V check terminal  
+1.8 V measuring terminal.  
TP3500 (A-4) : +2.5 V check terminal  
CN2700 (A-6) : ISP common connector  
+2.5 V measuring terminal.  
Used only for production in the assembly factory. Used for  
program writing into the JTAG device with ISP.  
TP3600 (A-4) : +3.3 V check terminal  
+3.3 V measuring terminal.  
<TEST terminal>  
E2300 (B-8), E3404 (P-13), E3407 (N-8), E3408 (L-11),  
E3410 (G-13), E3411 (P-1), E3412 (N-5), E3414 (L-2)  
E3417 (K-5), E3419 (E-7), E3421 (B-13), E3425 (E-3),  
E3426 (D-5), E3427 (K-12), E3429 (B-5) : GND  
terminal  
TP3700 (A-4) : +12 V check terminal  
+12 V measuring terminal.  
<LED on the CPU DK module> (C-10)  
Refer to < LED on the CPU DR module > in 1. CA-44  
Board.  
Use this terminal as the earth point for measuring the  
respective check terminals.  
<Switch on the CPU DK module> (C-10)  
Refer to < Switch on the CPU DR module > in 1. CA-44  
Board.  
TP1300 (G-13), TP1400 (E-13) : ERR check  
terminal  
SDI signal error measuring terminal.  
TP2301 (A-9) : CPU CK (CPU clock) signal check  
terminal  
Used to check the CPU clock.  
TP3300 (L-13) : FLOE (field odd even) signal  
check terminal  
FLOE signal measuring terminal.  
TP3301 (M-13) : HD (horizontal sync) signal check  
terminal  
HD signal measuring terminal.  
TP3302 (M-13) : CKX (control timing) signal check  
terminal  
CKX signal measuring terminal.  
TP3303 (M-13) : VD (vertical sync) signal check  
terminal  
VD signal measuring terminal.  
TP3308 (L-12) : CK1 (clock for video signal) signal  
Uses this terminal when checking the clock signal for video.  
MVS-8000SF  
1-37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
7. XPT-21 board (MVS-8000SF)  
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
TP2  
3
TP1  
E10  
4
E7  
CN3301  
D3401  
5
D2  
D3  
D4  
E1  
6
CN3303  
7
E9  
E8  
CN3001  
S3401  
8
E2  
9
A
B
C
D
E
F
S3301  
DI1  
DI4  
10  
CPU-DK  
Module  
SW2  
CN3901  
E5  
11  
TP3401  
SW1  
12  
13  
E3  
E4  
TP3001  
5
4
3
2
1
TP3004  
TP3003  
TP3005  
TP3002  
E6  
A side/Component side  
<LED>  
<Switch>  
D3401 (A-5) : RESET status LED  
System reset status indication.  
Lit when S3401 is pressed or the power voltage drops to  
S3401 (A-8) : XPT-RESET switch  
Pressing this switch initializes the CPU on the XPT-21  
board.  
+3.3 V.  
S3301 (A-10) : MONITOR switch  
D3 (A-5) : +3.3 V  
Factory use only. (Do not change the setting.)  
+3.3 V power supply status indication.  
Lit when the +3.3 V power is supplied.  
<Connector>  
CN3001 (A-8) : ISP common connector  
Used only for production in the assembly factory. Used for  
program writing into the JTAG device with ISP.  
D4 (A-6) : +2.5 V  
+2.5 V power supply status indication.  
Lit when the + 2.5 V power is supplied.  
CN3301 (A-4) : TERMINAL pin  
This pin is connected to the CPU control terminal and used  
during maintenance.  
D2 (A-5) : +12 V  
+12 V power supply status indication.  
Lit when the +12 V power is supplied.  
Conforms to RS-232C.  
MVS-8000SF  
1-38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
<LED on the CPU DK module> (C-10)  
Refer to < LED on the CPU DK module > in 1. CA-44  
CN3303 (A-6) : DEBUG terminal  
Not used.  
board.  
This terminal conforms to RS-232C.  
<Switch on the CPU DK module> (C-10)  
Refer to < Switch on the CPU DK module > in 1. CA-44  
board.  
CN3901 (A-11) : IEEE1394 terminal  
Not used.  
This terminal conforms to IEEE1394.  
<TEST terminal>  
E1 (P-4), E2 (P-8), E3 (P-12), E4 (L-12), E5 (J-11),  
E6 (H-13), E7 (H-4), E8 (H-8), E9 (D-8), E10 (E-4) :  
GND terminal  
Use this terminal as the earth point for measuring the  
respective check terminals.  
TP1 (B-4) : +3.3 V check terminal  
+3.3 V measuring terminal.  
TP2 (D-3) : +2.5 V check terminal  
+2.5 V measuring terminal.  
TP3001 (M-12) : VCLK signal check terminal  
VCLK signal measuring terminal.  
TP3002 (L-13) : VD (vertical sync) signal check  
terminal  
VD signal measuring terminal.  
TP3003 (L-13) : HD (horizontal sync) signal check  
terminal  
HD signal measuring terminal.  
TP3004 (L-13) : FLOE (Field Odd Even) signal  
check terminal  
FLOE signal measuring terminal.  
TP3005 (L-13) : CKX (control timing) signal check  
terminal  
CKX signal measuring terminal.  
TP3401 (H-12) : EXT_CLK check terminal  
CPU clock measuring terminal.  
(KOA CPU clock check terminal)  
MVS-8000SF  
1-39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
8. OUT-23 board (MKS-8160HD)/OUT-24 board (MKS-8160SD)/OUT-27 board (MKS-8160M)  
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
TP1306  
TP1206  
TP1106  
TP1006  
S100  
D100  
3
TP101  
D104  
TP1308  
TP1307  
TP1208  
TP1207  
TP1108  
TP1107  
TP1008  
TP1007  
TP102  
D105  
4
TP103  
D106  
TP104  
D1400  
D1401  
TP502  
TP501  
5
TP1001  
TP1000  
CN1400  
TP1002  
TP1005  
TP1004  
TP1003  
6
E107  
E103  
E102  
TP206 TP207  
7
S1501  
CN1502  
D503  
D502  
D501  
8
TP906  
TP806  
TP706  
TP606  
9
A
B
C
D
E
F
TP908  
TP907  
TP808  
TP807  
TP708  
TP707  
TP608  
TP607  
DI1  
10  
11  
12  
13  
DI4  
CPU-DK  
SW2  
*
Module  
TP602  
TP605  
TP604  
TP603  
TP202  
SW1  
TP601  
TP600  
E104  
TP203  
TP204  
TP201  
E105  
5
4
3
2
1
TP205  
* : The CPU-DK module is installed only in the OUT-23 board of slot 14.  
OUT-23 board A side/Component side  
MVS-8000SF  
1-40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
E108  
E101  
TP1301  
TP1201  
TP1101  
TP1001  
S100  
D100  
TP101  
D107  
3
D104  
TP102  
D105  
TP1302  
TP1202  
TP1102  
TP1002  
4
TP103  
D106  
TP502  
TP501  
TP104  
D1400  
D1401  
5
TP1300  
TP1200  
TP1100  
TP1000  
E107  
CN1400  
6
E103  
7
S1501  
CN1502  
TP901  
TP801  
TP701  
TP601  
D503  
D502  
D501  
8
9
A
B
C
D
E
F
DI1  
10  
11  
12  
13  
DI4  
CPU-DK  
SW2  
*
Module  
TP902  
TP802  
TP702  
TP602  
SW1  
TP800  
TP204  
TP203  
TP900  
TP700  
TP600  
TP202  
TP201  
E104  
TP205  
5
4
3
2
1
E109  
E105  
* : The CPU-DK module is installed only in the OUT-24 board of slot 14.  
OUT-24 board A side/Component side  
. OUT-23/24 board  
<LED>  
D100 (A-3) : +12 V  
D106 (A-4) : +2.5 V  
+12 V power supply status indication.  
Lit when the +12 V power is supplied.  
If this LED does not light, the fuse may have blown.  
+2.5 V power supply status indication.  
Lit when the +2.5 V power is supplied.  
D501, D502, D503 (A-8) : OUT-CPU status LED  
D104 (A-3) : +5 V (OUT-23 board)  
+5 V power supply status indication.  
Lit when the +5 V power is supplied.  
OUT-23 and OUT-24 boards CPU status indication.  
D1400 (A-5) : TBC-1 system status LED  
TBC-1 system CONFIG DONE status indication.  
Not lit when configuration is completed.  
D104 (A-4), D107 (A-3) : +5 V (OUT-24 board)  
+5 V power supply status indication.  
Lit when the +5 V power is supplied.  
D1401 (A-5) : TBC-2 system status LED  
TBC-2 system CONFIG DONE status indication.  
Not lit when configuration is completed.  
D105 (A-4) : +3.3 V  
+3.3 V power supply status indication.  
Lit when the +3.3 V power is supplied.  
MVS-8000SF  
1-41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
<Switch>  
TP203 (N-12) : HD (horizontal sync) signal check  
terminal (OUT-23 board)  
HD signal measuring terminal.  
S100 (A-3) : OUT-CPU RESET switch  
Pressing this switch initializes the CPU on the OUT-23/24  
board.  
TP204 (N-13) : FLOE (field odd even) signal check  
terminal  
FLOE signal measuring terminal.  
S1501 (A-7) : MONITOR reset switch  
The reset switch that is used to reset the monitor during  
maintenance through the terminal.  
TP203 (P-12) : HD (horizontal sync) signal check  
terminal (OUT-24 board)  
<Connector>  
CN1400 (A-5) : ISP common connector  
Used only for production in the assembly factory. Used for  
program writing into the JTAG device with ISP.  
HD signal measuring terminal.  
TP204 (P-12) : FLOE (Field Odd Even) signal  
check terminal  
CN1502 (A-8) : TERMINAL pin  
This pin is connected to the control terminal and used  
during maintenance.  
FLOE signal measuring terminal.  
TP205 (J-13), TP206 (J-7) : CK (clock for video)  
signal check terminal (OUT-23 board)  
<TEST terminal>  
Uses this terminal when checking the clock signal for video.  
E102 (E-7), E103 (H-6), E104 (J-12), E105 (P-13),  
E107 (P-6) : GND terminal (OUT-23 board)  
Use this terminal as the earth point for measuring the  
respective check terminals.  
TP205 (J-13), TP206 (J-6) : EAV_C signal check  
terminal (OUT-24 board)  
CLOCK signal measuring terminal.  
E103 (J-6), E104 (K-13), E105 (P-13), E107 (P-5),  
E109 (D-13), E108 (J-1), E1010 (P-1) : GND  
terminal (OUT-24 board)  
TP207 (K-7) : VCO CLOCK signal check terminal  
(OUT-23 board)  
VCO CLOCK signal measuring terminal.  
Use this terminal as the earth point for measuring the  
respective check terminals.  
TP501 (P-5) : CPU_OE signal check terminal  
CPU_OE signal measuring terminal.  
TP101 (A-3) : +12 V check terminal  
+12 V measuring terminal.  
TP502 (P-5) : CPU_WE signal check terminal  
CPU_WE signal measuring terminal.  
TP102 (A-4) : +5 V check terminal  
+5 V measuring terminal.  
TP600 (N-12), TP1000 (N-5) : 1R001 signal check  
terminal (OUT-23 board)  
TP103 (A-4) : +3.3 V check terminal  
1R001 signal measuring terminal.  
+3.3 V measuring terminal.  
TP601 (N-12), TP1001 (N-5) : HANC signal check  
terminal (OUT-23 board)  
TP104 (A-4) : +2.5 V check terminal (OUT-23 board)  
+2.5 V measuring terminal.  
HANC signal measuring terminal.  
TP104 (A-5) : +2.5 V (OUT-24 board)  
+2.5 V measuring terminal.  
TP602 (N-11), TP1002 (N-5) : LINE signal check  
terminal (OUT-23 board)  
LINE signal measuring terminal.  
TP201 (P-13) : VD (vertical sync) signal check terminal  
VD signal measuring terminal.  
TP603 (N-12), TP1003 (N-5) : FRAME signal check  
terminal (OUT-23 board)  
TP202 (P-12) : CKX (control timing) signal check terminal  
FRAME signal measuring terminal.  
CKX signal measuring terminal.  
MVS-8000SF  
1-42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
TP604 (N-12), TP1004 (N-5) : CRC signal check  
terminal (OUT-23 board)  
CRC signal measuring terminal.  
TP605 (N-11), TP1005 (N-5) : SIG_DET signal  
check terminal (OUT-23 board)  
SIG_DET signal measuring terminal.  
TP606 (N-8), TP706 (L-9), TP806 (J-9), TP906 (G-9),  
TP1006 (N-2), TP1106 (L-2), TP1206 (J-2), TP1306  
(F-2) : PLL_LOCK signal check terminal (OUT-23  
board)  
PLL_LOCK signal measuring terminal.  
TP607 (N-10), TP707 (L-10), TP807 (J-10), TP907  
(G-10), TP1007 (N-4), TP1107 (L-4), TP1207 (J-4),  
TP1307 (F-4) : EAV_Y signal check terminal (OUT-  
23 board)  
EAV_Y signal measuring terminal.  
TP602 (P-10), TP702 (L-10), TP802 (J-10), TP902 (G-10),  
TP1002 (N-4), TP1102 (L-4), TP1202 (J-4), TP1302 (F-4) :  
EAV_Y signal check terminal (OUT-24 board)  
EAV_Y signal measuring terminal.  
TP608 (N-10), TP708 (L-10), TP808 (J-10), TP908 (G-10),  
TP1008 (N-3), TP1108 (L-3), TP1208 (J-4), TP1308 (F-4) :  
EAV_C signal check terminal (OUT-23 board)  
EAV_C signal measuring terminal.  
TP600 (M-12), TP601 (M-8), TP700 (K-11), TP701 (K-8),  
TP800 (H-12), TP801 (H-8), TP900 (E-12), TP901 (F-8),  
TP1000 (M-5), TP1001 (M-2), TP1100 (J-5), TP1101 (K-2),  
TP1200 (G-5), TP1201 (G-2), TP1300 (E-5), TP1301 (E-2) :  
V_FRQ signal check terminal (OUT-24 board)  
V_FRQ signal measuring terminal.  
<LED on the CPU DK module> (C10)  
Refer to < LED on the CPU DR module > in 1. CA-44  
board.  
<Switch on the CPU DK module> (C10)  
Refer to < Switch on the CPU DR module > in 1. CA-44  
board.  
MVS-8000SF  
1-43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
A
B
C
D
E
F
G
H
J
E5  
K
L
M
N
P
1
E2  
2
S1  
D1  
TP1  
3
TP700  
D9504  
D9004  
TP9001  
TP9501  
4
D1600  
S1600  
E1  
E3  
TP702  
TP701  
5
CN1400  
TP1500  
E6  
TP1400 TP1300  
TP1200  
6
S2100  
7
CN1902  
D702  
D701  
D700  
TP2100  
8
A
B
C
D
E
F
9
DI1  
DI4  
CPU-DK  
SW2  
*
10  
11  
12  
Module  
SW1  
TP1100  
E7  
TP1000 TP900  
TP205  
TP800  
TP202  
5
4
3
2
1
TP203  
TP204  
E4  
TP201  
* : The CPU-DK module is installed only in the OUT-27 board of slot 14.  
OUT-27 board A side/Component side  
. OUT-27 board  
<LED>  
<Switch>  
D1 (A-3) : +12 V  
S1 (A-3) : OUT-CPU RESET switch  
Pressing this switch initializes the CPU on the OUT-27  
board.  
+12 V power supply status indication.  
Lit when the +12 V power is supplied.  
If this LED does not light, the fuse may have blown.  
S1600 (A-5) : JTAG switch  
D700, D701, D702 (A-8) : OUT-CPU status LED  
OUT-27 board CPU status indication.  
Used only for production in the assembly factory. Set this  
switch to ON only when writing program in the JTAG  
device with ISP.  
D1600 (A-4) : CONF ERR status LED  
FPGA (EP20K100E) CONFIG DONE status indication.  
Not lit when all configurations are completed.  
S2100 (A-7) : MONITOR reset switch  
The reset switch that is used to reset the monitor during  
maintenance through the terminal.  
D9004 (A-4) : +1.8 V  
+1.8 V power supply status indication.  
Lit when the +1.8 V power is supplied.  
D9504 (A-3) : +3.3 V  
+3.3 V power supply status indication.  
Lit when the +3.3 V power is supplied.  
MVS-8000SF  
1-44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
<Connector>  
TP2100 (B-8) : CPU CK (CPU clock) signal check  
terminal  
Uses this terminal when checking the CPU clock.  
CN1600 (A-5) : ISP common connector  
Used only for production in the assembly factory. Used for  
program writing into the JTAG device with ISP.  
TP9001 (A-4) : +1.8 V check terminal  
CN1902 (A-7) : TERMINAL pin  
This pin is connected to the control terminal and used  
during maintenance.  
+1.8 V measuring terminal.  
TP9501 (A-4) : +3.3 V check terminal  
+3.3 V measuring terminal.  
<TEST terminal>  
<LED on the CPU DK module> (C10)  
Refer to < LED on the CPU DR module > in 1. CA-44  
Board.  
E1 (A-5), E2 (N-1), E3 (N-5), E4 (N-12), E5 (J-1), E6 (G-7),  
E7 (G-12) : GND terminal  
Use this terminal as the earth point for measuring the  
respective check terminals.  
<Switch on the CPU DK module> (C10)  
Refer to < Switch on the CPU DR module > in 1. CA-44  
Board.  
TP1 (A-3) : +12 V check terminal  
+12 V measuring terminal.  
TP201 (M-12) : VD (vertical sync) signal check terminal  
VD signal measuring terminal.  
TP202 (M-12) : CKX (control timing) signal check terminal  
CKX signal measuring terminal.  
TP203 (M-12) : HD (horizontal sync) signal check  
terminal  
HD signal measuring terminal.  
TP204 (M-12) : FLOE (field odd even) signal check  
terminal  
FLOE signal measuring terminal.  
TP205 (J-12), TP206 (J-7) : CK (clock for video)  
signal check terminal  
Uses this terminal when checking the clock signal for video.  
TP700 (N-3) : CPU_CS2 signal check terminal  
CPU_CS2 signal measuring terminal.  
TP701 (M-5) : CPU_OE signal check terminal  
CPU_OE signal measuring terminal.  
TP702 (M-5) : CPU_WE signal check terminal  
CPU_WE signal measuring terminal.  
TP800 (L-11), TP900 (K-11), TP1000 (H-11), TP1100 (G-11),  
TP1200 (L-5), TP1300 (K-5), TP1400 (H-5), TP1500 (G-5) :  
ERR check terminal  
SDI signal error measuring terminal.  
MVS-8000SF  
1-45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
9. DIO-62 board (MKS-8440HD)/DIO-63 board (MKS-8440SD)/DIO-74 board (MKS-8440M)  
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
TP2000  
TP2500  
TP3000  
TP3500  
D1  
TP2  
D5  
3
4
5
6
7
TP2001  
TP2002  
TP2501  
TP2502  
TP3001  
TP3002  
TP3501  
TP3502  
E1  
E5  
TP100  
D6  
TP1  
D7  
TP3  
D100  
D101  
TP4  
E4  
E2  
S1  
8
TP4000  
TP4500  
TP5500  
TP5000  
E6  
TP4001  
TP4002  
TP4501  
TP4502  
TP5001  
TP5002  
TP5501  
TP5502  
9
10  
TP1007  
TP1006  
TP1002  
TP1005  
TP1004  
TP1001  
TP1503  
TP1000  
TP1507  
TP1506  
TP1502  
TP1505  
TP1504  
TP1501  
TP1503  
TP1500  
E3  
11  
12  
13  
E7  
TP6  
TP5  
DIO-62 board A side/Component side  
MVS-8000SF  
1-46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
TP2000  
TP2500  
TP3000  
TP3500  
E1  
D1  
3
4
5
6
7
8
9
TP2  
D6  
E5  
TP1  
D7  
TP3501  
TP3502  
TP3  
TP2001  
TP2002  
TP2501  
TP2502  
TP3001  
TP3002  
E6  
D100  
D101  
CN1  
TP4  
E4  
TP4500  
E2  
TP4000  
TP5000  
TP5500  
S1  
TP1001  
TP1501  
TP5501  
TP5502  
10  
11  
12  
13  
TP4001  
TP4002  
TP4501  
TP4502  
TP5001  
TP5002  
TP1000 TP1500  
E3  
E7  
TP5  
TP6  
DIO-63 board A side/Component side  
. DIO-62/63 board  
<LED>  
D1 (A-3) : +12 V  
D100 (A-5) : CONF1  
+12 V power supply status indication.  
Lit when the +12 V power is supplied.  
H2 to L2 FPGA (Spartan II) CONFIG DONE status  
indication.  
If this LED does not light, the fuse may have blown.  
Not lit when configuration is completed.  
D5 (A-3) : +5 V (DIO-62 board)  
+5 V power supply status indication.  
Lit when the +5 V power is supplied.  
D101 (A-6) : CONF2  
D10 to L10 FPGA (Spartan II) CONFIG DONE status  
indication.  
Not lit when configuration is completed.  
D6 (A-4) : +3.3 V  
+3.3 V power supply status indication.  
Lit when the +3.3 V power is supplied.  
<Switch>  
S1 (A-7) : DIO reset switch  
Pressing this switch initializes the CPU on the DIO-62 and  
DIO-63 board.  
D7 (A-5) : +2.5 V  
+2.5 V power supply status indication.  
Lit when the +2.5 V power is supplied.  
<Connector>  
CN1 (A-6) : ISP common connector  
Used only for production in the assembly factory. Used for  
program writing into the JTAG device with ISP.  
MVS-8000SF  
1-47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
<TEST terminal>  
TP9 (L-12) : HD (horizontal sync) signal check  
terminal (DIO-63 board)  
HD signal measuring terminal.  
E1 (N-3), E2 (P-6), E3 (P-11), E4 (H-6), E5 (F-3), E6 (A-8),  
E7 (E-12) : GND terminal (DIO-62 board)  
Use this terminal as the earth point for measuring the  
respective check terminals.  
TP10 (L-12) : FLOE (field odd even) signal check  
terminal (DIO-63 board)  
E1 (N-2), E2 (P-6), E3 (P-10), E4 (H-6), E5 (F-3), E6 (A-5),  
E7 (A-12) : GND terminal (DIO-63 board)  
Use this terminal as the earth point for measuring the  
respective check terminals.  
FLOE signal measuring terminal.  
TP100 (A-4) : +5 V check terminal (DIO-62 board)  
+5 V measuring terminal.  
TP1 (A-4) : +3.3 V check terminal  
TP3 (A-5) : +2.5 V check terminal  
+3.3 V measuring terminal.  
+2.5 V measuring terminal.  
TP2 (A-3) : +12 V check terminal  
+12 V measuring terminal.  
TP1000 (E-11), TP1500 (F-11) : 1R001 signal check  
terminal (DIO-62 board)  
1R001 signal measuring terminal.  
TP4 (K-6), TP5 (L-13), TP6 (H-13) : CK (clock for  
video) signal check terminal (DIO-62 board)  
Uses this terminal when checking the clock signal for video.  
TP1001 (E-11), TP1501 (F-11) : HANC signal check  
terminal (DIO-62 board)  
HANC signal measuring terminal.  
TP7 (N-13) : VD (vertical sync) signal check  
terminal (DIO-62 board)  
VD signal measuring terminal.  
TP1002 (E-11), TP1502 (F-11) : LINE signal check  
terminal (DIO-62 board)  
LINE signal measuring terminal.  
TP8 (P-13) : CKX (control timing) signal check  
terminal (DIO-62 board)  
CKX signal measuring terminal.  
TP1003 (E-11), TP1503 (F-11) : FRAME signal  
check terminal (DIO-62 board)  
FRAME signal measuring terminal.  
TP9 (P-13) : HD (horizontal sync) signal check  
terminal (DIO-62 board)  
HD signal measuring terminal.  
TP1004 (E-11), TP1504 (F-11) : CRC signal check  
terminal (DIO-62 board)  
CRC signal measuring terminal.  
TP10 (P-13) : FLOE (field odd even) signal check  
terminal (DIO-62 board)  
FLOE signal measuring terminal.  
TP1005 (E-11), TP1505 (F-11) : SIG DET signal  
check terminal (DIO-62 board)  
SIG DET signal measuring terminal.  
TP4 (K-6), TP5 (J-13), TP6 (H-13) : CK (clock for  
video) signal check terminal (DIO-63 board)  
Uses this terminal when checking the clock signal for video.  
TP1006 (E-11), TP1506 (F-11), TP2001 (G-3),  
TP2501 (J-3), TP3001 (K-3), TP3501 (M-3), TP4001 (G-9),  
TP4501 (J-9), TP5001 (K-9), TP5501 (M-9) : EAV_Y  
signal check terminal (DIO-62 board)  
TP7 (L-12) : VD (vertical sync) signal check  
terminal (DIO-63 board)  
EAV_Y signal measuring terminal.  
VD signal measuring terminal.  
TP1007 (E-10), TP1507 (F-10), TP2002 (G-3), TP2502 (J-3),  
TP3002 (K-3), TP3502 (M-3), TP4002 (G-9), TP4502 (J-9),  
TP5002 (K-9), TP5502 (M-9) : EAV_C signal check  
terminal (DIO-62 board)  
TP8 (L-12) : CKX (control timing) signal check  
terminal (DIO-63 board)  
CKX signal measuring terminal.  
EAV_C signal measuring terminal.  
MVS-8000SF  
1-48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
TP2000 (H-2), TP2500 (K-2), TP3000 (L-3), TP3500  
(N-3), TP4000 (L-3), TP4500 (K-8), TP5000 (L-8),  
TP5500 (N-8) : PLL_LOCK signal check terminal  
(DIO-62 board)  
PLL_LOCK signal measuring terminal.  
TP1000 (D-11), TP1500 (E-11), TP2000 (G-2),  
TP2500 (J-2), TP3000 (K-2), TP3500 (M-2), TP4000 (G-7),  
TP4500 (J-7), TP5000 (K-7), TP5500 (M-7) :  
VCO_FRQ signal check terminal (DIO-63 board)  
VCO_FRQ signal measuring terminal.  
TP1001 (E-9), TP1501 (G-9), TP2001 (H-5), TP2501 (J-5),  
TP3001 (L-5), TP3501 (N-9), TP4001 (H-10), TP4501 (K-10),  
TP5001 (L-10), TP5501 (N-9) : EAV_Y signal check  
terminal (DIO-63 board)  
EAV_Y signal measuring terminal.  
TP2002 (H-5), TP2502 (J-5), TP3002 (L-5), TP3502 (N-4),  
TP4002 (H-10), TP4502 (J-10), TP5002 (L-10),  
TP5502 (N-10) : EAV_C signal check terminal  
(DIO-63 board)  
EAV_C signal measuring terminal.  
MVS-8000SF  
1-49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
E1  
D1  
3
4
5
6
7
8
9
TP1  
D3  
E5  
TP9501  
D2  
TP9001  
D501  
E6  
TP102  
E4  
E2  
S601  
CN601  
S1  
10  
11  
12  
13  
TP1001 TP1501  
E3  
E7  
TP101  
TP104  
TP103  
DIO-74 board A side/Component side  
. DIO-74 board  
<LED>  
<Switch>  
D1 (A-3) : +12 V  
+12 V power supply status indication.  
Lit when the +12 V power is supplied.  
S1 (A-9) : DIO reset switch  
Pressing this switch initializes the CPU on the DIO-74  
board.  
If this LED does not light, the fuse may have blown.  
S601 (A-8) : JTAG switch  
D2 (A-4) : +1.8 V  
+1.8 V power supply status indication.  
Lit when the +1.8 V power is supplied.  
Used only for production in the assembly factory. Set this  
switch to ON only when writing program in the JTAG  
device with ISP.  
D3 (A-4) : +3.3 V  
<Connector>  
+3.3 V power supply status indication.  
Lit when the +3.3 V power is supplied.  
CN601 (A-8) : ISP common connector  
Used only for production in the assembly factory. Used for  
program writing into the JTAG device with ISP.  
D501 (A-4) : CONF ERR  
FPGA (EP20K100E) CONFIG DONE status indication.  
Not lit when all configurations are completed.  
MVS-8000SF  
1-50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
<TEST terminal>  
E1 (N-2), E2 (P-6), E3 (P-10), E4 (H-6), E5 (F-3), E6 (A-5),  
E7 (C-12) : GND terminal  
Use this terminal as the earth point for measuring the  
respective check terminals.  
TP1 (A-3) : +12 V check terminal  
+12 V measuring terminal.  
TP101 (P-12), TP102 (J-6), TP103 (J-13), TP104 (D-13) :  
CK (clock for video) signal check terminal  
Uses this terminal when checking the clock signal for video.  
TP201 (L-12) : VD (vertical sync) signal check  
terminal  
VD signal measuring terminal.  
TP202 (L-12) : CKX (control timing) signal check  
terminal  
CKX signal measuring terminal.  
TP203 (L-12) : HD (horizontal sync) signal check  
terminal  
HD signal measuring terminal.  
TP204 (L-12) : FLOE (field odd even) signal check  
terminal  
FLOE signal measuring terminal.  
TP9001 (A-4) : +1.8 V check terminal  
+1.8 V measuring terminal.  
TP9501 (A-4) : +3.3 V check terminal  
+3.3 V measuring terminal.  
TP1001 (D-11), TP1501 (E-11) : ERR check terminal  
SDI signal error measuring terminal.  
MVS-8000SF  
1-51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
10. MY-102 board (MKS-8440HD/SD/M)  
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
3
E123  
TP203  
TP204  
TP704  
TP705  
TP706  
E131  
E124  
4
S202  
D201  
D202  
D203  
S201  
5
E132  
D3  
D2  
D1  
6
E601  
7
CN14  
E801  
8
TP904  
E121  
E130  
CN12  
D12  
TP905  
TP906  
9
D18  
D19  
D14  
D15  
D16  
D17  
E122  
E129  
10  
11  
12  
13  
CPU-DR  
Module  
SW2  
SW1  
D10  
D13  
TP504  
E1001  
E508  
TP507  
TP506  
TP505  
A side/Component side  
<LED>  
D1, D2, D3 (A-6) : MY-CPU status LED  
Status indication of the CPU on the MY-102 board.  
<Switch>  
S201 (A-5) : MY-CPU reset switch  
Pressing this switch initializes the CPU on the MY-102  
board.  
D201 (A-5) : +12 V  
+12 V power supply status indication.  
Lit when the +12 V power is supplied.  
If this LED does not light, the fuse may have blown.  
S202 (A-5) : MONITOR reset switch  
The reset switch that is used to reset the monitor during  
maintenance through the terminal.  
D202 (A-5) : +3.3 V  
<Connector>  
+3.3 V power supply status indication.  
Lit when the +3.3 V power is supplied.  
CN12 (A-8) : ISP common connector  
Used only for production in the assembly factory. Used for  
program writing into the JTAG device with ISP.  
D203 (A-5) : +1.8 V  
+1.8 V power supply status indication.  
Lit when the +1.8 V power is supplied.  
CN14 (A-7) : TERMINAL pin  
This pin is connected to the CPU control terminal and used  
during maintenance.  
Conforms to RS-232C.  
MVS-8000SF  
1-52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
<TEST terminal>  
E121 (P-8), E122 (P-10), E123 (P-3), E124 (P-4),  
E129 (P-11), E130 (P-9), E131 (P-4), E132 (P-5),  
E508 (E-12), E601 (D-7), E801 (N-7), E1001 (N-12) :  
GND terminal  
Use this terminal as the earth point for measuring the  
respective check terminals.  
TP203 (C-3) : +3.3 V check terminal  
+3.3 V measuring terminal.  
TP204 (C-5) : +1.8 V check terminal  
+1.8 V measuring terminal.  
TP504 (F-2) : CKX (control timing) signal check  
terminal  
CKX signal measuring terminal.  
TP505 (E-12), TP706 (L-4), TP906 (L-8) : FLOE  
(field odd even) signal check terminal  
FLOE signal measuring terminal.  
TP506 (E-12), TP704 (L-4), TP904 (K-8) : VD  
(vertical sync) signal check terminal  
VD signal measuring terminal.  
TP507 (F-12), TP705 (K-4), TP905 (K-8) : HD  
(horizontal sync) signal check terminal  
HD signal measuring terminal.  
<LED on the CPU DR module> (C-10)  
Refer to < LED on the CPU DR module > in 1. CA-44  
board.  
<Switch on the CPU DR module> (C-10)  
Refer to < Switch on the CPU DR module > in 1. CA-44  
board.  
MVS-8000SF  
1-53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
11. CC-90 board (MKS-8420M)  
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
TP101  
D107  
3
TP9501  
D101  
TP9001  
D102  
4
TP9301  
D103  
E101  
S2001  
E103  
5
CN2001  
6
TP402  
CN401  
S101  
7
TP401  
E106  
TP400  
8
S400  
E105  
9
D12  
E108  
D18  
D19  
D14  
D15  
D16  
D17  
TP900  
TP1200  
10  
11  
12  
13  
CPU-DR  
Module  
SW2  
SW1  
D10  
D13  
TP205  
E104  
TP202  
TP201  
D803  
TP204  
TP203  
D804  
D805  
D801  
D802  
E107  
A side/Component side  
<LED>  
D107 (A-3) : +12 V  
D803, D804, D805 (A-10) : CC-CPU status LED  
+12 V power supply status indication.  
Indicates the CPU status on the CC-90 board.  
Lit when the +12 V power is supplied.  
If this LED does not light on, the fuse may have blown.  
D801 (A-10) : DLL status LED  
Indicates lock/unlock of the DLL (Delay Locked Loop) in  
the CC-90 board.  
D101 (A-3) : +3.3 V  
+3.3 V power supply status indication.  
Lit when the +3.3 V power is supplied.  
If this LED lit, the DLL can possibly be unlocked.  
D802 (A-10) : FPGA CONFIG status LED  
CC-90 board FPGA CONFIG DONE status indication.  
Not lit when all configurations are completed.  
D102 (A-4) : +1.8 V-1  
+1.8 V-1 power supply status indication.  
Lit when the +1.8 V-1 power is supplied.  
D103 (A-4) : +1.8 V-2  
+1.8 V-2 power supply status indication.  
Lit when the +1.8 V-2 power is supplied.  
MVS-8000SF  
1-54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
<Switch>  
TP401 (C-7) : CPU half clock signal check  
S2001 (A-5) : JTAG switch  
terminal  
Used only for production in the assembly factory. Set this  
switch to ON only when writing program in the JTAG  
device with ISP.  
Use this terminal to check the CPU half clock signal.  
TP402 (B-7) : CPU clock signal check terminal  
Use this terminal to check the CPU clock signal.  
S101 (A-8) : CC-CPU reset switch  
Pressing this switch initializes the CPU on the CC-90  
board.  
TP900 (M-10), TP1200 (K-10) : ERR check terminal  
SDI signal error measuring terminal.  
S400 (A-8) : Monitor reset switch  
TP201 (L-13) : VD (vertical sync) signal check  
The reset switch that is used to reset the monitor during  
maintenance through the terminal.  
terminal  
Use this terminal to check the VD signal that is used in this  
circuit board.  
<Connector>  
CN2001 (A-6) : ISP common connector  
Used only for production in the assembly factory. Used for  
program writing into the JTAG device with ISP.  
TP202 (L-12) : CKX (control timing) signal check  
terminal  
Use this terminal to check the CKX signal that is used in  
this circuit board.  
CN401 (A-7) : Terminal pin  
This pin is connected to the control terminal and used  
during maintenance.  
TP203 (M-13) : HD (horizontal sync) signal check  
terminal  
Conforms to RS-232C.  
Use this terminal to check the HD signal that is used in this  
circuit board.  
<TEST terminal>  
E101 (A-5), E103 (D-5), E104 (L-12), E105 (N-8),  
E106 (B-8), E107 (B-13), E108 (J-9) : GND terminal  
Use this terminal as the earth point for measuring the  
respective check terminals.  
TP204 (M-12) : FLOE (field odd even) signal check  
terminal  
Use this terminal to check the FLOE signal that is used in  
this circuit board.  
TP101 (A-3) : +12 V check terminal  
+12 V measuring terminal.  
TP205 (L-12) : VCLK (clock for video signal)  
signal check terminal  
Use this terminal to check the clock for video signal.  
TP9501 (A-3) : +3.3 V check terminal  
+3.3 V measuring terminal.  
<LED on the CPU DR module> (C11)  
Refer to < LED on the CPU DR module > in 1. CA-44  
Board.  
TP9001 (A-4) : +1.8 V-1 check terminal  
+1.8 V-1 measuring terminal.  
<Switch on the CPU DR module> (C11)  
Refer to < Switch on the CPU DR module > in 1. CA-44  
Board.  
TP9301 (A-4) : +1.8 V-2 check terminal  
+1.8 V-2 measuring terminal.  
TP400 (C-8) : System clock signal check terminal  
Use this terminal to check the system clock signal supplied  
from CPU module.  
MVS-8000SF  
1-55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
12. CNI-9 board (Suffix : -12) (MKS-8110HD)  
A
B
C
D
E
F
G
H
J
K
L
1
2
S101  
S501  
S1001  
S601  
S701  
S1201  
S1501  
S901  
S1301  
S1401  
S1601  
S301  
S401  
S801  
S1101  
S1701  
S201  
3
4
CNI-9 board A side/Component side  
<Switch>  
S101 (A-3), S201, S301 (B-3), S401, S501 (C-3), S601 (D-3), S701, S801 (E-3), S901 (F-3),  
S1001, S1101 (G-3), S1201 (H-3), S1301, S1401 (J-3), S1501, S1601 (K-3), S1701 (L-3) :  
Output band-width compensation switch  
They are the output band-width compensation ON/OFF switches.  
Use these switches in the factory setting positions.  
Factory setting  
S101 to S1701 : All OFF  
MVS-8000SF  
1-56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8. Checks on Completion of Installation  
1-8-2. Checks on the Switch Setting the Number of Power Supply Units  
Before turning on the power of the MVS-8000SF, confirm that the switch S303 on the CA-44 board is set  
in the following position (default setting).  
S303 (B-1)/CA-44 board : Switch setting the number of power supply units (DIP type)  
S303-1 : OFF  
S303-2 : OFF  
S303-3 : ON  
S303-4 : OFF  
A
B
C
D
4
E
S303  
1
2
3
5
1
2
3
4
5
F
E
D
C
B
A
CPU-DK  
Module  
(COM CPU-1)  
CPU-DR  
Module  
(MAIN CPU)  
1
2
3
4
5
F
E
D
C
B
A
CPU-DK  
Module  
(COM CPU-2)  
B
A
1
2
1
A
IF-844  
(S-BUS)  
2
3
B
SG-272  
MVS-8000SF  
1-57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-9. System Connection  
1-9. System Connection  
Configure the MVS-8000 system connections referring to the connection example as shown below.  
1. Connection example  
*b  
Reference video signal  
Ethernet switch*a  
Ethernet switch*a  
CTRL EDITOR  
DATA LAN  
DME Processor Pack  
MVE-8000  
Editing Control System  
BVE-9100  
Reference  
video signal *b  
CTRL  
DATA  
CTRL REMOTE 1  
PERIPH  
System Control Unit  
MKS-8010  
REMOTE  
DATA  
Reference  
video signal *b  
BKS-R series  
HDS-X series  
Switcher Processor Pack  
MVS8000SF-C  
Device Control Unit Pack DCU-8000  
PERIPH  
Reference  
video signal *b  
Audio mixer  
VTR  
DDR  
Crossover cable  
BNC cable  
*a : Connect each LAN (CTRL, DATA) to the separate Ethernet switches respectively.  
However, a single Ethernet switch can be used for connecting each LAN.  
*b : Terminate the system with the 75 Z terminators supplied. The 75 Z terminators are supplied with the equipment.  
MVS-8000SF  
1-58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-9. System Connection  
2. Flow of Video Signals  
DME Processor Pack  
MVE-8000  
SWITCHER B  
SWITCHER A  
Reference video *c  
signal  
AC100 to 240 V Power Supply *a  
AC100 to 240 V Power Supply *b  
Reference video *c  
signal  
DME 1A  
DME 1B  
PRIMARY INPUTS  
1 to 34  
Camera  
VTR  
Routing Switcher  
AC100 to 240 V Power Supply *b  
AC100 to 240 V Power Supply *b  
OUTPUTS  
1 to 16  
AC100 to 240 V Power Supply *b  
Switcher Processor Pack  
MVS8000SF-C  
MONITOR  
VTR  
Video Signal Input  
Video Signal Output  
68-pin Cable  
Video/Key Signal  
AC Power Supply  
*a : For the AC power cord, refer to “Optional Items” of the “DME Processor Pack MVE-8000” Operation Manual.  
*b : For the AC power cord, refer to “Optional Items” of the “Multi-Format Switcher Processor MVS-8000”  
Operation Manual (15 page).  
*c : Terminate the system with the 75 Z terminators supplied with this unit.  
MVS-8000SF  
1-59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section 2  
Service Overview  
2-1. Troubleshooting  
The main power of the MVS-8000 cannot be  
turned on. (Indicator does not light green.)  
The monitor picture is not displayed correctly.  
A picture is not displayed  
on the monitor screen even  
though the main power of  
the MVS-8000SF is turned  
on.  
The main power of the  
MVS-8000SF cannot be  
turned on. (Indicator does  
not light green.)  
Install the standard boards  
Are the standard boards  
installed into the specified  
slots?  
NO  
NO  
into the specified slots.  
(Refer to MVS-8000SF  
Maintenance Manual.)  
Are two or more power  
switches of the MVS-8000SF  
turned on?  
Set two or more power  
switches of the MVS-8000SF  
to on.  
NO  
NO  
YES  
YES  
Are the option boards  
installed into the specified  
slots?  
Install the option boards into  
the specified slots.  
(Refer to Section 1-4.)  
Is the power cord of the  
MVS-8000SF connected  
correctly?  
Connect it correctly.  
YES  
YES  
NO  
NO  
Check connections of the  
Are the input and output  
input and output equipment.  
cables connected correctly?  
The power supply unit is  
probably defective.  
YES  
Is the Software installed  
correctly?  
Install the software correctly.  
(Refer to the Use s Guide.)  
YES  
The MVS-8000SF is  
probably defective.  
MVS-8000SF  
2-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-2. Periodic Inspection and Maintenance  
2-3. About the Data Backup Capacitor  
2-2. Periodic Inspection and Maintenance  
2-2-1. Cleaning  
2. Fan  
MVS-8000SF is air-cooled by the fans (on both sides).  
If dust has accumulated in the intake of the fan, air is  
prevented from flowing smoothly and this may result in a  
temperature rise inside the machine. This may have an  
adverse effect on performance and the life of the machine.  
Cleaning of the fan every month is recommended.  
Contact your local Sony Sales Office/Service Center for  
information on cleaning the fan.  
1. Front panel  
The filter on the rear of the front panel can easily accumu-  
late the dust. Be sure to remove dust by cleaning as  
follows.  
(1) Remove the front panel. (Refer to Section 1-4-1.)  
(2) Remove the dust accumulated on the filter with a  
vacuum cleaner.  
Fan  
n
Cleaning the filter by washing in water is recommend-  
ed when there is a heavy accumulation of dust.  
Be sure to dry the filter completely after it has been  
washed.  
Fans  
Front panel  
Fans  
Fan  
Filter  
2-3. About the Data Backup Capacitor  
A large capacitor is installed on the CA-44 board in order  
to backup the memory storing the setup and other data in  
the MVS-8000SF.  
Leave the main power of the MVS-8000SF turned on for  
one hour or longer in order to charge the large capacitor.  
The data can be backed up for about one week when the  
capacitor is fully charged under the normal operating  
temperature.  
MVS-8000SF  
2-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The material contained in this manual consists of  
information that is the property of Sony Corporation.  
Sony Corporation expressly prohibits the duplication of  
any portion of this manual or the use thereof for any  
purpose other than the operation or maintenance of the  
equipment described in this manual without the express  
written permission of Sony Corporation.  
Le matériel contenu dans ce manuel consiste en  
informations qui sont la propriété de Sony Corporation.  
Sony Corporation interdit formellement la copie de  
quelque partie que ce soit de ce manuel ou son emploi  
pour tout autre but que des opérations ou entretiens de  
l’équipement à moins d’une permission écrite de Sony  
Corporation.  
Das in dieser Anleitung enthaltene Material besteht aus  
Informationen, die Eigentum der Sony Corporation sind.  
Die Sony Corporation untersagt ausdrücklich die  
Vervielfältigung jeglicher Teile dieser Anleitung oder den  
Gebrauch derselben für irgendeinen anderen Zweck als  
die Bedienung oder Wartung der in dieser Anleitung  
beschriebenen  
Ausrüstung  
ohne  
ausdrückliche  
schriftliche Erlaubnis der Sony Corporation.  
MVS-8000SF  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Printed in Japan  
2003. 3 16  
©2002  
Sony Corporation  
MVS8000SF-C (SY) E  
3-620-565-03  
B&P Company  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sharp Car Satellite TV System LC 60LE650LX User Manual
Sony Camcorder XC 003 User Manual
Sony CRT Television KDL 40W580B User Manual
Sony Mixer D NE300 User Manual
Sony Personal Computer PCV RX462DS User Manual
Sony Portable Speaker SRS T80 User Manual
Standard Horizon Fish Finder Hx500s User Manual
State Industries Water Heater SBN85390NE A User Manual
Stoelting Freezer E112 User Manual
Sunbeam Coffeemaker BVMC KG1 User Manual