®
INSTALLATION MANUAL
Sony Electronics Inc.
16450 West Bernardo Drive
San Diego, CA 92127
Download from Www.Somanuals.com. All Manuals Search And Download.
Stand diagrams
PART#:
SPMTRI/C
MATERIALS USED:
12 (GA) CRS, Clear acrylic base
COLOR:
Silver
A. Back plate
B. Stand support
C. Clear base
D. Security access screws
E. (1) Cable access hole
F. Fixed tabletop mounting holes
Dimensions are in Inch and mm
18.25
(463.5)
20.50
(520.7)
20.00
(508)
1.00
(25.4)
12 X 22
(304 x 558)
(A)
MODEL
A
PFM-32C1
.37 (9.4)
1.0 (25.4)
.72 (18.2)
1.0 (25.4)
.90 (22.8)
1.0 (25.4)
FWD32LX1,FWD32DV1
PFM-42B1,PFM-42V1, FWD-50PX2
PFM-42LX1, FWD42DV1
PFM-50C1
PFM-50DV1
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
TOOLS & SUPPLY NEEDED
HARDWARE
Phillips screwdriver
(4) M5 x 10 (mm) flat head Phillip screws (4) Clear rubber feet
(6) M5 x 30 (mm) flat head Phillip screws (2) M6 x 30 Phillips head screws (used on the 30” plasma only)
(2) M5 x 12 (mm) phillip security screws (used on 42" and 50" plasma displays only)
(2) #10 x 1-3/4" wood screws (Optional use)
Building the stand
Step 1
Unpack the components from the box and set them on the floor. Invert and apply the four (4) clear rubber feet to the flat surface on the
base, locate the four mounting points on the clear base. Secure the two (2) upright supports (flat surface facing out) to the base by using
the four (6) M5 x 30 (mm) Phillip screws (supplied). CAUTION: Do not over tighten the screws.
Uprights
Clear base
(6) M5 x 30
Flat head screws
Step 2
The stand fits a 32" 42" and 50" PFM series (Sony plasma displays only). The plate is stamped with two plasma sizes. Check the size that
fits your plasma before installing. NOTE: If using a 32” plasma, the plate is not needed. Mount the plasma quick release sleeves from
the plasma to the key-holes on the uprights.
The size and arrow must always point up prior to installation, finger tighten the (4) M5 x 10 (mm) phillips flat head screws then tighten the
screws. See figure 2.
50"
42"
(4) M5 x 10
Flat head screws
Mounting plate
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Securing the plasma to the stand
Step 3
Raise the display with the securing sleeves installed to the plasma. Slip the sleeves through the four (4) keyholes on the back plate and
drop it down slowly, make sure all of the four (4) sleeves are in the keyhole slot before letting go of the plasma. On the 42" and 50" two (2)
M5 x 12 Phillip screws (security screws) can be used for additional security. See figure 3.
NOTE: If using a 32” plasma, secure it with the two (2) M6 x 30 Phillip screws supplied.
NOTE: Two (2) security screws for
the 42" and 50" plasma displays.
Check all hardware for proper
tightness and security.
M5 x 12 phillips
screws
NOTE: Security screws for the 32”
plasma displays. Check all hardware
for proper tightness and security.
M6 x 30 phillips
screws
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
(Optional) fixed installation
Step 1
Invert the stand and locate the two (2) mounting points on the bottom of the stand for (optional) fixed tabletop installation. Measure the
distance between center to center of these two (2) holes and mark the table. See figure 4.
NOTE: This diagram shows
the bottom of the stand.
Wood screw
access holes
Step 2
OPTIONAL TABLE MOUNTING
If securing to a wood table, mark the table and drill properly. Secure the stand with the two (2) #10 x 1-1/4" wood screws (supplied).
NOTE: Longer or shorter wood screws and or mounting hardware depending on your installation environment are (commercially
available). See figure 5.
#10x1-1/4”
woodscrews
Flat wood surface
NOTE: Check all hardware for proper
tightness and security.
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
|