3-869-571-12 (1)
Digital
Videocassette
Recorder
Operating Instructions
Before operating the unit, please read this manual
thoroughly and retain it for future reference.
The supplied CD-ROM includes Operating Instructions
for the DSR-series Digital Video Cassette Recorder or Player
(English, Japanese, French, German, Italian and Spanish versions).
DSR-1800A/1800AP
© 2005 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: THIS WARNING IS APPLICABLE FOR
USA ONLY.
The manufacturer of this product is Sony Corporation, 1-
7-1 Konan, Minato-ku, Tokyo, Japan.
Using this unit at a voltage other than 120 V may require
the use of a different line cord or attachment plug, or both.
To reduce the risk of fire or electric shock, refer servicing
to qualified service personnel.
The Authorized Representative for EMC and product
safety is Sony Deutschland GmbH, Hedelfinger Strasse
61, 70327 Stuttgart, Germany. For any service or
guarantee matters please refer to the addresses given in
separate service or guarantee documents.
For the customers in Taiwan only
For the customers in the USA (DSR-1800A only)
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause
harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your
authority to operate this equipment.
All interface cables used to connect peripherals must be
shielded in order to comply with the limits for a digital
device pursuant to Subpart B of Part 15 of FCC Rules.
WARNING
Excessive sound pressure from earphones and headphones
can cause hearing loss.
In order to use this product safely, avoid prolonged
listening at excessive sound pressure levels.
For the customers in Europe (DSR-1800AP only)
This product with the CE marking complies with both the
EMC Directive and the Low Voltage Directive issued by
the Commission of the European Community.
Compliance with these directives implies conformity to
the following European standards:
• EN60065: Product Safety
• EN55103-1: Electromagnetic Interference(Emission)
• EN55103-2: Electromagnetic Susceptibility(Immunity)
This product is intended for use in the following
Electromagnetic Environments:
E1 (residential), E2 (commercial and light industrial), E3
(urban outdoors), E4 (controlled EMC environment, ex.
TV studio)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Le fabricant de ce produit est Sony Corporation, 1-7-1
Konan, Minato-ku, Tokyo, Japon.
AVERTISSEMENT
Le représentant autorisé pour EMC et la sécurité des
produits est Sony Deutschland GmbH, Hedelfinger Strasse
61, 70327 Stuttgart, Allemagne. Pour toute question
concernant le service ou la garantie, veuillez consulter les
adresses indiquées dans les documents de service ou de
garantie séparés.
Afin de réduire les risques d’incendie ou
d’électrocution, ne pas exposer cet
appareil à la pluie ou à l’humidité.
Afin d’écarter tout risque d’électrocution,
garder le coffret fermé. Ne confier l’entretien
de l’appareil qu’à un personnel qualifié.
WARNUNG
Um die Gefahr von Bränden oder
elektrischen Schlägen zu verringern, darf
dieses Gerät nicht Regen oder
CET APPAREIL DOIT ÊTRE RELIÉ À LA
TERRE.
ATTENTION
Feuchtigkeit ausgesetzt werden.
Eviter d’exposer l’appareil à un égouttement ou à des
éclaboussures. Ne placer aucun objet rempli de liquide,
comme un vase, sur l’appareil.
Um einen elektrischen Schlag zu
vermeiden, darf das Gehäuse nicht geöffnet
werden. Überlassen Sie Wartungsarbeiten
stets nur qualifiziertem Fachpersonal.
Cet appareil n’est pas déconnecté de la source
d’alimentation secteur tant qu’il est raccordé à la prise
murale, même si l’appareil lui-même a été mis hors
tension.
DIESES GERÄT MUSS GEERDET WERDEN.
ACHTUNG
Das Gerät ist nicht tropf- und spritzwassergeschützt. Es
dürfen keine mit Flüssigkeiten gefüllten Gegenstände, z.
B. Vasen, darauf abgestellt werden.
Des programmes de télévision, films, bandes vidéo et
autres peuvent être protégés par des droits d’auteur.
L’enregistrement non autorisé de tels matériaux risque de
constituer une violation de ces droits d’auteur.
Solange das Netzkabel an eine Netzsteckdose
angeschlossen ist, bleibt das Gerät auch im
ausgeschalteten Zustand mit dem Strommetz verbunden.
AVERTISSEMENT
Une pression acoustique excessive en provenance des
écouteurs ou du casque peut provoquer une baisse de
l’acuité auditive.
Pour utiliser ce produit en toute sécurité, évitez l’écoute
prolongée à des pressions sonores excessives.
Fernsehprogramme, Filme, Videobänder usw. können
urheberrechtlich geschützt sein. Unerlaubtes Aufnehmen
solcher Materialien verstößt gegen das Urheberrecht.
Pour les clients européens
(DSR-1800AP seulement)
WARNUNG
Ce produit portant la marque CE est conforme à la fois à la
Directive sur la compatibilité électromagnétique (EMC) et
à la Directive sur les basses tensions émises par la
Commission de la Communauté Européenne.
La conformité à ces directives implique la conformité aux
normes européennes suivantes :
Zu hoher Schalldruck von Ohrhörern und Kopfhörern
kann Gehörschäden verursachen.
Um dieses Produkt sicher zu verwenden, vermeiden Sie
längeres Hören bei sehr hohen Schalldruckpegeln.
Für Kunden in Europa (Nur DSR-1800AP)
Dieses Produkt besitzt die CE-Kennzeichnung und erfüllt
die EMV-Richtlinie sowie die Niederspannungsrichtlinie
der EG-Kommission.
• EN60065: Sécurité des produits
• EN55103-1: Interférences électromagnétiques (émission)
• EN55103-2: Sensibilité électromagnétique (immunité)
Ce produit est prévu pour être utilisé dans les
environnements électromagnétiques suivants :
E1 (résidentiel), E2 (commercial et industrie légère), E3
(urbain extérieur) et E4 (environnement EMC contrôlé, ex.
studio de télévision).
Angewandte Normen:
• EN60065: Sicherheitsbestimmungen
• EN55103-1: Elektromagnetische Verträglichkeit
(Störaussendung)
• EN55103-2: Elektromagnetische Verträglichkeit
(Störfestigkeit)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Für die folgenden elektromagnetischen Umgebungen:
E1 (Wohnbereich), E2 (kommerzieller und in
beschränktem Maße industrieller Bereich), E3
(Stadtbereich im Freien) und E4 (kontrollierter EMV-
Bereich, z.B. Fernsehstudio).
ATTENZIONE
Per ridurre il rischio di incendi o scosse
elettriche, non esporre questo apparato
alla pioggia o all’umidità.
Der Hersteller dieses Produkts ist Sony Corporation, 1-7-1
Konan, Minato-ku, Tokyo, Japan.
Per evitare scosse elettriche, non aprire
l’involucro. Per l’assistenza rivolgersi
unicamente a personale qualificato.
Der autorisierte Repräsentant für EMV und
Produktsicherheit ist Sony Deutschland GmbH,
Hedelfinger Strasse 61, 70327 Stuttgart, Deutschland. Bei
jeglichen Angelegenheiten in Bezug auf Kundendienst
oder Garantie wenden Sie sich bitte an die in den separaten
Kundendienst- oder Garantiedokumenten aufgeführten
Anschriften.
QUESTO APPARECCHIO DEVE ESSERE
MESSO A TERRA.
ATTENZIONE
L’apparecchio non deve essere esposto a gocciolamenti o
spruzzi. Non collocare sull’apparecchio oggetti contenenti
liquidi, come ad esempio vasi di fiori.
1. Für Ihren privat genutzten Videorecoder muß eine
Fernseh-Rundfunk-Genehmigung beantragt
werden, sofern nicht bereits eine Genehmigung für
ein Fernsehgerät desselben Haushaltes vorliegt. Im
geschäftlichen Bereich ist jeder einzelne
Videorecorder anmelde- und gebührenpflichtig.
(Auskunft ggf. bei der GEZ oder den
AVVERTIMENTO
L’apparecchio non è scollegato dalla fonte di
alimentazione CA (corrente di rete) fintanto che è
collegato ad una presa di corrente, anche se l’apparecchio
stesso è stato spento.
Rundfunkanstalten.)
2. Im privaten Bereich ist die Aufzeichnung von
urheberrechtlich geschützten Werken auf Bild-
und Tonträger gestattet. Die entsprechenden
Urheber-Vergütungen sind im Kaufpreis des
Gerätes enthalten. Öffentliche Wiedergabe oder
Verbreitung von mitgeschnittenen
Programmi televisivi, film, videonastri e altro materiale
possono essere tutelati dai diritti d’autore.
Registrazioni non autorizzate di tali materiali possono
infrangere la legge sui diritti d’autore.
Fernsehsendungen ist ohne Erlaubnis nicht
zulässig, verpflichtet zu Schadenersatz und ist
gegebenenfalls strafbar.
AVVERTENZA
Un’eccessiva pressione sonora da auricolari e cuffie può
causare la perdita dell’udito.
3. Im Rahmen der Regelung des §47 des
Urheberrechtsgesetzes sind Aufzeichnungen von
Schulfernsehprogrammen gestattet. Mitschnitte
von Schulfunksendungen dürfen jedoch nur für
den Unterricht verwendet werden und sind
spätestens am Ende des laufenden Schuljahres zu
löschen.
Per usare questo prodotto in maniera sicura, evitare
l’ascolto prolungato a livelli eccessivi di pressione sonora.
Per i clienti in Europa (DSR-1800AP soltanto)
Questo prodotto recante il marchio CE è conforme sia alla
direttiva sulla compatibilità elettromagnetica (EMC) che
alla direttiva sulle basse tensioni emesse dalla
Commissione della Comunità Europea.
La conformità a queste direttive implica la conformità alle
seguenti normative europee:
• EN60065: Sicurezza dei prodotti
• EN55103-1: Interferenza elettromagnetica (Emissione)
• EN55103-2: Sensibilità ai disturbi elettromagnetici
(Immunità)
Questo prodotto è destinato all’uso nei seguenti ambienti
elettromagnetici:
E1 (residenziali), E2 (commerciali e industriali leggeri),
E3 (esterni urbani) e E4 (ambienti EMC controllati, ad
esempio studi televisivi).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Il fabbricante di questo prodotto è la Sony Corporation, 1-
7-1 Konan, Minato-ku, Tokyo, Giappone.
Para los clientes de Europa (DSR-1800AP sólo)
Este producto con marcado CE cumple con las directivas
de compatibilidad electromagnética y baja tensión de la
Comisión Europea.
El cumplimiento de estas directivas implica la
conformidad con los siguientes estándares europeos:
• EN60065: Seguridad del producto
• EN55103-1: Interferencia electromagnética (Emisión)
• EN55103-2: Susceptibilidad electromagnética
(Inmunidad)
Este producto está ha sido diseñado para utilizarse en los
entornos electromagnéticos siguientes:
La rappresentanza autorizzata per EMC e la sicurezza dei
prodotti è la Sony Deutschland GmbH, Hedelfinger
Strasse 61, 70327 Stoccarda, Germania. Per qualsiasi
questione riguardante l’assistenza o la garanzia, si prega di
rivolgersi agli indirizzi riportati nei documenti
sull’assistenza o sulla garanzia a parte.
ADVERTENCIA
Para reducir el riesgo de electrocución, no
exponga este aparato a la lluvia ni a la
humedad.
E1 (zona residencial), E2 (zona comercial e industrial
ligera), E3 (exteriores urbanos), y E4 (entorno con EMC
controlada, p. ej., estudio de televisión).
El fabricante de este producto es Sony Corporation, con
dirección en 1-7-1 Konan, Minato-ku, Tokio, Japón.
El Representante autorizado para EMC y seguridad del
producto es Sony Deutschland GmbH, Hedelfinger Strasse
61, 70327 Stuttgart, Alemania. Para asuntos relacionados
con el servicio y la garantía, consulte las direcciones
entregadas por separado para los documentos de servicio o
garantía.
Para evitar descargas eléctricas, no abra el
aparato. Solicite asistencia técnica
únicamente a personal especializado.
ESTE APARATO DEBE CONECTARSE A
TIERRA.
PRECAUCIÓN
No se debe exponer la unidad a goteos o salpicaduras.
Tampoco se deben colocar sobre la misma objetos llenos
de líquido, tales como un florero.
La unidad no queda desconectada de la alimentación
eléctrica siempre que esté conectado al tomacorriente
incluso aunque se desconecte el interruptor principal.
Los programas de televisión, las películas, las cintas de
vídeo y material similar pueden estar protegidos por las
leyes de copyright.
La grabación no autorizada de dicho material puede ir en
contra de lo establecido por las leyes de copyright.
ADVERTENCIA
Una excesiva presión de sonido de los auriculares y cascos
auriculares puede provocar una pérdida de percepción de
sus oídos.
Para utilizar este producto con seguridad, no escuche
durante mucho tiempo con niveles de presión de sonido
excesivos.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
High-Speed and Low-Speed Search—Quickly and
Table of Contents
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview Chapter
1
Because the recording is digital, multi-generation dubbing
can be performed with virtually no deterioration of quality.
Features
Wide track pitch
1
The DSR-1800A/1800AP is a / -inch digital video
4
The recording track pitch is 15 µm, fully 50 percent wider
than the 10-µm track pitch of the DV format. Thanks to this
feature, the DVCAM format sufficiently meets the
reliability and precision requirements of professional
editing.
cassette recorder using the DVCAM digital recording
format. It achieves stable, superb picture quality by
digitally processing video signals separated into color
difference signals and luminance signals (component
method).
The unit is equipped with a variety of functions needed for
videocassette recorders and players used in professional
digital video editing systems.
The unit is also equipped with an i.LINK interface, thus
enabling simple connection with a nonlinear editing*
system supporting DV format.
Furthermore, the unit is equipped with a full-fledged
analog interface to support hybrid systems that combine
conventional analog equipment with digital equipment.
High-quality PCM digital audio
PCM recording makes for a wide dynamic range and a
high signal-to-noise ratio, thereby enhancing sound
quality.
There are two recording modes: 2-channel mode (48-kHz
sampling and 16-bit quantization), which offers sound
quality equivalent to the DAT (Digital Audio Tape)
format, or 4-channel mode (32-kHz sampling and 12-bit
quantization).
* Non-linear editing: This is an editing method that uses video and audio
signals digitally encoded and recorded on a hard disk as digital data. When
compared with conventional (linear) editing methods, non-linear editing
offers vastly improved efficiency in editing operations, for example, by
eliminating tape transport time.
Playback compatibility with DV and
DVCPRO formats
A DV cassette recorded on a DV format VCR (excluding
the tapes recorded in LP mode) as well as a DVCPRO
(25M) format recorded cassette can be played back on this
unit.
The main features of the unit are described in the
following.
DVCAM Format
Note
When playing back a tape recorded in DVCPRO (25M)
it is not possible to play back the cue-audio track of the
tape.
DVCAM is based on the consumer DV format, which uses
1
the 4:1:1 component digital format, and provides a / -inch
4
digital recording format for professional use.
High picture quality, high stability
Video signals are separated into color difference signals
and luminance signals, which are encoded and compressed
to one-fifth size before being recorded to ensure stable and
superb picture quality.
Features
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Support for three cassette sizes
Remote control
There are two sizes of DVCAM cassette: standard and
mini. You can use either size with this unit.
The unit also accepts L and M sizes of DVCPRO cassette.
• When a cassette is inserted, the reel mechanism of the
unit automatically adjusts to the size of the inserted
cassette.
• The capacity of a standard cassette is 184 minutes of
recording/playback, and that of a mini cassette is 40
minutes.
The unit can be operated by remote control from an editing
control unit that supports the RS-422A interface or from an
optional SIRCS*-compatible remote control unit such as
the DSRM-10.
* SIRCS (Sony Integrated Remote Control System): A command protocol
to remote control Sony professional videocassette recorders/players.
Playback control using search dial
The search dial on the front panel of the unit allows you to
carry out playback operation in jog or shuttle mode
without requiring an external editing control unit or remote
control unit to be connected to the unit.
A Wealth of Interfaces
Digital interfaces
i.LINK (DV)*: The unit can input and output digital video
and audio signals in DV format.
* i.LINK and are trademarks and indicate that this product is in agreement
with IEEE1394-1995 specifications and their revisions.
High-speed search function
You can carry out color picture searches during fast
forward and rewind at speeds up to 85 times normal speed.
When remote-controlling this unit in shuttle mode from an
editing control unit or a remote control unit, you can search
at any speed in the range 0 (still) to 60 times normal speed
in both directions. You can also search frame-by-frame in
jog mode.
SDI (serial digital interface)/AES/EBU (optional
DSBK-1801 SDI/AES/EBU Input/Output Board):
When the unit is fitted with the optional DSBK-1801
board, it can input and output D1 (component) format
digital video and audio signals and also AES/EBU-
format digital audio signals.
At search speeds up to 10 times normal speed in both
directions, you can also hear playback audio.
Analog interfaces
Digital slow-motion playback
The unit also comes with analog interfaces enabling it to be
connected to analog video and audio equipment.
Analog video: These interfaces include a component
interface, composite interface, and S-video interface.
Analog audio: Four channels each of input and output are
provided. It is also possible to connect a microphone to
the unit.
Using the frame memory function, the unit can show
noise-free slow-motion playback at speeds ranging from 0
1
to / times normal speed in both directions.
2
Digital jog sound function
1
When searching at speeds in the range +1 to + / or
30
1
− / to −1* times normal speed, the digital jog sound
30
function is enabled. The audio signal is saved in temporary
memory, and replayed according to the search speed. This
allows searching on the sound track.
Facilities for High-Efficiency Editing
The unit provides an abundance of functions that enhance
editing efficiency and precision.
* The positive direction refers to forward movement of the tape, and the
negative direction to reverse movement.
Cross-fade editing
For audio editing, you can select from cut-in editing, fade-
in/fade-out editing, and cross-fade editing.
Video process control
For analog video output and SDI-format video output, you
can adjust the video output level, chroma signal output
level, setup level (for DSR-1800A), black level (for DSR-
1800AP), and chroma phase.
Internal time code generator and reader
An internal time code generator and reader enables time
code compliant with SMPTE (for DSR-1800A)/EBU
(DSR-1800AP) format to be recorded and played back.
This allows editing to single frame precision.
Outputting or inputting time code (LTC) to or from an
external device is also possible using the TIME CODE IN/
OUT connectors.
Other Features
Menu system for functionality and
operation settings
The unit provides a menu system to make its various
functions easier to use and set up its operation conditions.
The unit is also compatible with VITC.
Features
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Superimposition function
Time code values, operation mode indications, error
messages, and other text data can be superimposed and
output in analog composite video signals.
Using the CD-ROM
Manual
Easy maintenance functions
The supplied CD-ROM includes Operating Instructions
for the DSR-series Digital Video Cassette Recorder or
Player (English, Japanese, French, German, Italian and
Spanish versions).
Self-diagnostic/alarm function: This function
automatically detects setup and connection errors,
operation faults, and other problems. It also displays a
description of the problem, its cause, and the
recommended response on the video monitor screen or
time counter display.
CD-ROM System Requirements
Digital hours meter: The digital hours meter functions
include four kinds of tally operations for operating
hours, head drum usage hours, tape transport hours,
and tape threading/unthreading times. The tally results
can be viewed on the video monitor or the time counter
display.
The following are required to access the supplied CD-
ROM disc.
• Computer: PC with Intel Pentium CPU
- Installed memory: 64 MB or more
- CD-ROM drive: × 8 or faster
• Monitor: Monitor supporting resolution of 800 × 600 or
higher
Compatible with wide-screen aspect ratio
(16:9)
• Operating system: Microsoft Windows XP Professional
or Windows XP Home Edition
The unit can record and play back aspect ratio information.
When video accompanied by wide-screen aspect ratio
information is recorded or played back, the unit can output
the video signal also containing the aspect ratio
information.
When these requirements are not met, access to the CD-
ROM disc may be slow, or not possible at all.
Preparations
One of the following programs must be installed on your
computer in order to use the Operating Instructions
contained on the CD-ROM disc.
• Adobe Acrobat Reader Version 4.0 or higher
• Adobe Reader Version 6.0 or higher
Rack mountable
When you use an optional rack mount kit, you can mount
this unit onto an EIA-standard 19-inch rack (height = 4
units).
Note
Optional Accessories
If Adobe Reader is not installed, you can download it from
the following URL:
http://www.adobe.com/
DSBK-1801 SDI/AES/EBU Input/Output
Board
When installed in the unit, this optional board enables
digital video and audio signals in the D1 format and also
AES/EBU-format digital audio signals to be transferred
between this unit and digital Betacam VCRs or other
digital equipment.
Reading the CD-ROM Manual
To read the Operating Instructions contained on the CD-
ROM disc, do the following.
1 Insert the CD-ROM disc in your CD-ROM drive.
RMM-131/1 Rack Mount Kit
This kit can be used to mount the unit onto an EIA-
standard 19-inch rack.
A cover page appears automatically in your browser.
If it does not appear automatically in the browser,
double-click the index.htm file on the CD-ROM disc.
2 Select and click the Operating Instructions that you
want to read.
This opens the PDF file of the Operating Instructions.
Using the CD-ROM Manual
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
If you lose the CD-ROM disc or become unable to read its
content, for example because of a hardware failure, you
can do one of the following.
• You can purchase a new CD-ROM disc to replace one
that has been lost or damaged. Contact your Sony service
representative.
• You can purchase printed versions of the Operating
Instructions (English version). Contact your Sony
service representative.
When ordering, be sure to specify the part number of the
manual you want.
Part No.
Models covered
3-869-571-1X
DSR-1800A/1800AP
•
•
•
Intel and Pentium are registered trademarks of Intel Corporation or its
subsidiaries in the United States and other countries.
Microsoft and Windows are registered trademarks of Microsoft
Corporation in the United States and/or other countries.
Adobe, Acrobat, and Adobe Reader are trademarks of Adobe Systems
Incorporated in the United States and/or other countries.
Using the CD-ROM Manual
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Location and Function of Parts
Front Panel
a POWER switch
b Audio level meters
A Input selection/audio mode
display section (see page 14)
c Cassette compartment
POWER
OVER
OVER
OVER
OVER
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
INPUT
VIDEO
i.LINK
COMPOSITE Y-R,B
S
VIDEO SDI SG
-12
-20
1
-12
-20
1
-12
-20
1
-12
-20
1
CH11/2
AUDIO
CH23/4
0
-1
-2
1
0
-1
-2
2
0
-1
-2
3
0
-1
-2
4
ANALOG AES/EBU
ANALOG AES/EBU
SDI SG
SDI SG
-30
-40
-30
-40
-30
-40
-30
-40
PB FS
48k44.1k32k REC MODE
2CH4CH
-60
-60
-60
-60
A
B
MARK
B Menu control panel (inside of
F Remote control setting
section (see page 20)
the door) (see page 15)
g AUDIO INPUT LEVEL control knobs
E Search control section
f CONTROL S connector
e HEADPHONES connector
d PHONE LEVEL control knob
a POWER switch
c Cassette compartment
Accepts DVCAM, DV and DVCPRO (25M)
videocassettes.
Press the “ ” side to power the unit on. When the unit is
powered on, the display windows in the front panel lights.
To power the unit off, press the “ ” side of the switch.
b Audio level meters
These show the audio levels of channels 1 to 4 (recording
levels in recording mode or E-E mode* and playback level
in playback mode).
d PHONE LEVEL control knob
Controls the volume of the headphones connected to the
HEADPHONES connector.
* E-E mode: Abbreviation of “Electric-to-Electric mode.” In this mode,
video and audio signals input to the VCR are output after passing through
internal electric circuits, but not through magnetic conversion circuits such
as heads and tapes. This can be used to check input signals and for
adjusting input signal levels.
Location and Function of Parts
13
Download from Www.Somanuals.com. All Manuals Search And Download.
e HEADPHONES connector (stereo phone jack)
Connect stereo headphones for headphone monitoring
during recording or playback.
The audio signal you want to monitor can be selected with
the MONITOR SELECT switches on the menu control
panel.
g AUDIO INPUT LEVEL control knobs
When recording, you can use these knobs to set audio input
levels for CH-1 (channel 1), CH-2, CH-3 and CH-4,
respectively.
You can make these knobs inoperative with the REC
f CONTROL S connector (stereo minijack)
Connect a SIRCS-compatible remote control unit such as
the DSRM-10.
A Input selection/audio mode display section
a INPUT display
b VIDEO display
c AUDIO CH1 1/2 display
d AUDIO CH2 3/4 display
e REC MODE display
f PB FS display
a INPUT display
e REC MODE (audio recording mode) display
Indicates the audio recording mode (2CH or 4CH) selected
i.LINK: When you press the SDTI/i.LINK button in the
INPUT SELECT section, the i.LINK indicator lights.
This indicates that digital video and audio signals in
i.LINK-compatible DV format are currently selected.
f PB FS (playback audio sampling frequency)
display
b VIDEO display
Indicates the sampling frequency (48 kHz, 44.1 kHz or 32
kHz) at which audio is recorded on tape.
Indicates the input video signal selected with the VIDEO
IN button in the INPUT SELECT section.
COMPOSITE: Composite video signal
Y−R, B: Y, R−Y and B−Y component video signals
S VIDEO: S-video signal
SDI: SDI video signal (optional DSBK-1801 board
required)
SG: Video test signal
c AUDIO CH1 1/2 display
Indicates the input audio signal selected with the CH-1,1/2
button in the INPUT SELECT section.
ANALOG: Analog audio signal
AES/EBU: Digital audio signal in AES/EBU format
(optional DSBK-1801 board required)
SDI: SDI audio signal (optional DSBK-1801 board
required)
SG: Audio test signal
d AUDIO CH2 3/4 display
Indicates the input audio signal selected with the CH-2,3/4
button in the INPUT SELECT section. The indications
available are the same as for the AUDIO CH1 1/2 display
described above.
Location and Function of Parts
14
Download from Www.Somanuals.com. All Manuals Search And Download.
B Menu control panel
The menu control panel is located on the inside of the door
at the lower front of the unit. Pull the top of the door to
open it.
a MONITOR SELECT switches
b INPUT SELECT section
c MENU button
d COUNTER SEL button
e RESET (NO) button
MIX
A
B
f SET (YES) button
MARK
g
buttons
h TC PRESET button
i SC PHASE control
j SYNC PHASE control
a MONITOR SELECT switches
Switch setting
Selected channel and output
format
Use these switches to select the channels for audio output
via the AUDIO MONITOR OUT connector on the rear
panel and the HEADPHONES connector on the front
panel.
Use the left switch to select the basic channel setting, then
use the right switch to select the output format (monaural,
stereo, or mix).
Left
switch
Right
switch
HEADPHONES AUDIO
connector
MONITOROUT
connector
Channel 1 only Channel 1 only
(monaural) (monaural)
CH-
1/3
CH-
2/4
MIX
Channels 1 and Channels 1 and
2 (stereo) 2 (mix)
The following table lists the correspondence of left/right
switch settings and channel/output format selections.
CH-
1/3
CH-
2/4
CH-
1/2
CH-
3/4
MIX
Channel 2 only Channel 2 only
(monaural) (monaural)
CH-
1/3
CH-
2/4
MIX
Channel 3 only Channel 3 only
(monaural) (monaural)
CH-
1/3
CH-
2/4
MIX
Channels 3 and Channels 3 and
4 (stereo) 4 (mix)
CH-
1/3
CH-
2/4
CH-
1/2
CH-
3/4
MIX
Channel 4 only Channel 4 only
(monaural) (monaural)
CH-
1/3
CH-
2/4
MIX
Location and Function of Parts
15
Download from Www.Somanuals.com. All Manuals Search And Download.
b INPUT SELECT section
c MENU button
Press this button to display the menu on the monitor screen
and the time counter display. Press it again to return from
the menu display to the usual display.
VIDEO IN button
Each press of this button cycles through the following
input video signal selection options.
• Composite video signal input to the VIDEO IN
connectors
On how to use the menu, see Chapter 4 “Menu Settings.”
• Component video signals input to the COMPONENT
VIDEO IN connectors
d COUNTER SEL (selection) button
• S-video signal input to the S VIDEO IN connector
• SDI video signal input to the SDI IN connector (optional
DSBK-1801 board required)
• Video test signal (selected with the INT VIDEO SG
generator
Selects the type of time data to be shown in the time
counter display. Each press of this button cycles through
three indicator display options: COUNTER (CNT: count
value of the time counter), TC (time code), and U-BIT
(user bits).
Note
In the input selection/audio mode display section, the
VIDEO display shows the selection made with this button.
When the REMOTE button in the remote control setting
section is lit, the COUNTER SEL button does not operate.
In this case, make the time data selection via the remote
equipment that is connected to the REMOTE connector on
the rear panel.
CH1,1/2 (audio channel 1 or 1/2) button
Each press of this button cycles through the following
input audio signal selection options for audio channel 1
(when in 2-channel mode) or for audio channels 1 and 2
(when in 4-channel mode).
• Analog audio signal(s) input to the AUDIO IN CH-1
connector (when in 2-channel mode) or AUDIO IN CH-
1 and CH-2 connectors (when in 4-channel mode)
• Digital audio signal in AES/EBU format input to the
DIGITAL AUDIO (AES/EBU) IN CH-1/2 connector
(optional DSBK-1801 board required)
e RESET (NO) button
Press this button to:
• reset menu settings,
• reset the time count (COUNTER) shown in the time
counter display to zero, or
• send a negative response to the prompts issued by the
unit.
• SDI audio signal input to the SDI IN connector (optional
DSBK-1801 board required)
• Audio test signal (selected with the INT AUDIO SG
signal generator
In the input selection/audio mode display section, the
AUDIO CH1 1/2 display shows the selection made with
this button.
f SET (YES) button
Press this button to:
• save new settings, such as selected menu items and time
code settings, to the memory of the unit, or
• send a positive response to the prompts issued by the
unit.
g Arrow (JjKk) buttons
Use these buttons to move around the menu items, and also
for setting time code and user bit data.
CH2,3/4 (audio channel 2 or 3/4) button
Each press of this button cycles through the input audio
signal selection options for audio channel 2 (when in 2-
channel mode) or for audio channels 3 and 4 (when in 4-
channel mode). The input audio signal selection options
corresponding to those for the CH1,1/2 button described
above are available.
In the input selection/audio mode display section, the
AUDIO CH2 3/4 display shows the selection made with
this button.
For details on setting time code and user bit data, see
h TC (time code) PRESET button
Use this button when setting an initial time code value and
user bit data.
For details on setting time code and user bit data, see “To
SDTI/i.LINK (SDTI(QSDI) interface/i.LINK selection)
button
Selects digital video and audio signals in i.LINK-
compatible DV format, input to the DV IN/OUT
connector. When you press this button, the i.LINK
indicator lights in the input selection/audio mode display
section.
i SC (subcarrier) PHASE control
Turn this control to accurately adjust the subcarrier phase
of the composite video output signal of the unit with
respect to the reference video signal. Use a cross-point
(Phillips) screwdriver to turn it.
Location and Function of Parts
16
Download from Www.Somanuals.com. All Manuals Search And Download.
j SYNC (synchronization) PHASE control
Turn this control to accurately adjust the synchronization
the reference video signal. Use a cross-point (Phillips)
screwdriver to turn it.
phase of the output video signal of the unit with respect to
C Tape transport control section
a EJECT button
b REW button
c REC button
f STOP button
e F FWD button
d PLAY button
a EJECT button
When you press this button, it lights and the cassette is
f STOP button
Press this button to stop the current tape transport
automatically ejected after a few seconds.
operation.
Note
b REW (rewind) button
No tape transport control buttons other than the EJECT
and STOP buttons will work while the REMOTE button in
the remote control setting section is lit. This can be
changed with the LOCAL ENABLE menu item (see page
63).
When you press this button, it lights and the tape starts
rewinding (maximum 85 times normal speed).
PB, you can monitor the playback picture during the
rewind.
c REC (record) button
When you press the PLAY button while holding down this
button, it lights and recording begins.
d PLAY button
When you press this button, it lights and playback begins.
If you press this button during recording or editing, the
recording or editing operation is stopped and this unit
enters playback mode.
e F FWD (fast forward) button
When you press this button, it lights and the tape is fast
forwarded (maximum 85 times normal speed).
PB, you can monitor the playback picture during the fast
forward.
Location and Function of Parts
17
Download from Www.Somanuals.com. All Manuals Search And Download.
D Display section
a Recording/playback format indicators
b ClipLink indicator
c VITC indicator
d Time data type indicators
e Time counter display
i CHANNEL CONDITION indicators
h SERVO indicator
g Cassette memory indicator
f REC INHIBIT indicator
j REPEAT indicator
k Tape end alarm indicator
l SHUTTLE/JOG indicators
m NOT EDITABLE indicator
a Recording/playback format indicators
DVCAM: This lights when a tape recorded in DVCAM
format is played back.
DV: This lights when a tape recorded in consumer DV
format is played back.
Note
A tape recorded in LP mode cannot be played back
correctly. When a tape recorded in LP mode is played
back, “DV LP” flashes and audio is muted.
LP: This lights when a tape recorded in LP mode is played
back.
When a tape recorded in DVCPRO (25M) format or any
other format than those mentioned above is played back,
none of the above indicators lights.
b ClipLink indicator
Lights when a cassette is loaded on which ClipLink log
data is stored in the cassette memory.
c VITC indicator
Lights when VITC is being read or recorded regardless of
the data shown in the time counter display.
Location and Function of Parts
18
Download from Www.Somanuals.com. All Manuals Search And Download.
d Time data type indicators
the search dial is turned clockwise causing playback to
take place in the forward direction, the G indicator lights.
When the search dial is turned counterclockwise causing
playback to take place in the reverse direction, the g
indicator lights. When the tape is stopped, the s indicator
lights.
One of the three indicators (COUNTER, U-BIT, and TC)
lights to indicate the type of time data currently shown in
the time counter display.
COUNTER: Count value of the time counter
U-BIT: User bit data
TC: SMPTE time code (for DSR-1800A) or EBU time
code (for DSR-1800AP)
For more information about the search dial, see “Search
dial” in the next section.
e Time counter display
Indicates the count value of the time counter, time code,
VITC, or user bit data depending on the settings of the
COUNTER SEL button on the menu control panel and the
TC SELECT menu item (see page 66).
m NOT EDITABLE indicator
Lights during playback of a tape that contains a recording
in other than the DVCAM format. When this indicator is
lit, the recordings contained in the tape can be used as
source material for editing, but editing operations such as
insert editing and assemble editing cannot be performed.
This indicator also lights when the audio recording mode
selected on this unit does not coincide with that of the
loaded tape.
Also used to display error messages and setup menu data.
f REC (recording) INHIBIT indicator
Lights in the following cases:
• The REC/SAVE switch on the loaded cassette is in the
SAVE position.
ON.
E Search control section
g Cassette memory indicator
Lights when a cassette provided with a memory chip
(“cassette memory”) is loaded.
h SERVO indicator
This indicator lights when the drum servo and capstan
servo are locked*.
* Servo lock: This refers to the synchronization of the phase of the drum
rotation and the reference signal for the tape transport position, so that the
video heads can trace the same pattern on the tape for playback and
recording.
b Search dial
i CHANNEL CONDITION indicators
These three-color indicators show the state of the playback
signal.
a SEARCH button
Green: The state of the playback signal is good.
Yellow: The playback signal is somewhat deteriorated, but
playback is possible.
Red: The playback signal is deteriorated. When the red
indicator remains on, head cleaning or an internal
inspection is necessary.
a SEARCH button
To use the search dial for playback in shuttle or jog mode,
press this button, turning it on. Pressing the dial toggles
between shuttle and jog modes. In shuttle mode, the
SHUTTLE indicator in the display section lights, and in
jog mode, the JOG indicator in the display section lights.
j REPEAT indicator
This indicator lights when the REPEAT MODE menu item
b Search dial
Turn this to carry out playback in the modes shown in the
following table. Turning the dial clockwise lights the G
indicator in the display section and plays back in the
forward direction. Turning the dial counterclockwise
lights the g indicator in the display section and plays back
in the reverse direction. When the tape is stopped, the s
indicator in the display section lights.
k Tape end alarm indicator
Starts flashing when the remaining capacity of the tape is
for about 2 minutes.
l SHUTTLE/JOG indicators
When searching in shuttle mode using the search dial, the
SHUTTLE indicator lights, and when searching in jog
mode using the search dial, the JOG indicator lights. When
Pressing this dial toggles playback between shuttle mode
and jog mode. When playing back in shuttle mode, the
Location and Function of Parts
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SHUTTLE indicator in the display section lights, and
when playing back in jog mode, the JOG indicator lights.
You can carry out noiseless playback in the range of
times normal speed.
When reverting to local mode to use the buttons in the tape
transport control section, press this button again, turning it
off.
1
/
2
b 9PIN button
Playback modes using the search dial
Playback mode Operation and functions
When carrying out remote control between this unit and
the unit connected to the REMOTE connector, press this
button, turning it on.
Shuttle
Press the SEARCH button or the search
dial so that the SHUTTLE indicator in
the display section lights, then turn the
search dial.
Playback is carried out at a speed
determined by the position of the search
dial. The maximum shuttle mode
playback speed can be changed with the
c i.LINK button
When carrying out remote control between this unit and
the unit connected to the DV IN/OUT connector, press
this button, turning it on.
Jog
Press the SEARCH button or the search
dial so that the JOG indicator in the
display section lights, then turn the
search dial. Playback is carried out at a
speed determined by the speed of
rotation of the search dial. The playback
speed is up to 1 times normal speed by
factory default.
The search dial has no detents.
You can use the SEARCH ENABLE menu item (see page
63) to select either of the following as the operation to be
performed to put the unit into search mode (shuttle or jog).
• Either press the SEARCH button or, except during
recording/editing, turn the search dial (factory default
setting).
• Press the SEARCH button.
F Remote control setting section
a REMOTE button
b 9PIN button
c i.LINK button
Note
When you edit using the DV IN/OUT connector, with
actually set may not be the same as the specified locations.
When you set video and audio signal input to “i.LINK”, set
remote control to “i.LINK” as well.
a REMOTE button
When remote-controlling this unit from the unit connected
to the REMOTE connector (page 25) or DV IN/OUT
connector (page 23), press this button, turning it on.
Location and Function of Parts
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel
SDI
OUT
DIGITAL AUDIO(AES/EBU)
CH-3/4 CH-3/4
DV IN/OUT
CH-1/2
CH-1/2
OUT
IN
IN
TIME CODE
IN
OUT
ANALOG VIDEO
COMPONENT VIDEO IN
REF.VIDEO
IN
S VIDEO COMPONENT VIDEO OUT
VIDEO IN
S VIDEO
IN
VIDEO OUT
Y
R-Y
OUT
1
2
OUT
Y
R-Y
B-Y
B-Y
(SUPER)
VIDEO CONTROL
LEVEL
LEVEL
LEVEL
LEVEL
LOW
OFF
HIGH
ON
LOW
OFF
HIGH
ON
LOW
OFF
HIGH
ON
LOW
OFF
HIGH
ON
MONITOR OUT
AUDIO
AUDIO IN
AUDIO OUT
600
Ω
600
Ω
600
Ω
600
Ω
REMOTE
CH-1
CH-2
CH-3
CH-1
CH-2
CH-3
CH-4
CH-4
~AC IN
AC IN connector
AC IN connector
Use the supplied power cord to connect this to an AC
outlet.
Location and Function of Parts
21
Download from Www.Somanuals.com. All Manuals Search And Download.
A Analog video signal input/output section
ANALOG VIDEO
COMPONENT VIDEO IN
REF.VIDEO
IN
S VIDEO
OUT
VIDEO IN
S VIDEO
IN
VIDEO OUT
Y
R-Y
OUT
1
2
Y
B-Y
(SUPER)
e VIDEO OUT 1 and 2 (SUPER)
connectors
d REF. VIDEO IN/OUT connectors
c COMPONENT VIDEO IN Y/R−Y/B−Y connectors
b S VIDEO IN connector
a VIDEO IN connectors
TIME CODE
S VIDEO COMPONENT VIDEO OUT
VIDEO OUT
2
OUT
Y
R-Y
IN
OUT
B-Y
h TIME CODE IN/OUT connectors
g COMPONENT VIDEO OUT Y/R−Y/B−Y connectors
f S VIDEO OUT connector
a VIDEO IN connectors (BNC type)
c COMPONENT VIDEO IN Y/R−Y/B−Y connectors
(BNC type)
Input analog component video signals (Y/R−Y/B−Y) to
these connectors.
Input an analog composite video signal. This connector
block has a built-in automatic 75 Ω termination switch.
When a signal is input to the left VIDEO IN connector
with no bridging (loop-through) connection made, the
connector is terminated with an impedance of 75 Ω
automatically. To connect the signal input to the left
VIDEO IN connector also to other equipment, use the right
d REF. (reference) VIDEO IN/OUT connectors
(BNC type)
Input a reference video signal. The IN connector block has
a built-in automatic 75 Ω termination switch. When a
signal is input to the left REF. VIDEO IN connector with
no bridging (loop-through) connection made, the
connector is terminated with an impedance of 75 Ω
automatically. To connect the reference video signal input
to the left REF. VIDEO IN connector also to other
equipment, use the right REF. VIDEO IN connector
VIDEO IN connector (marked
). When the right
VIDEO IN connector is used, the built-in 75 Ω termination
switch turns off automatically.
b S VIDEO IN connector (4-pin)
Input an S-video signal with separated Y (luminance) and
C (chroma: 3.58 MHz for DSR-1800A or 4.43 MHz for
DSR-1800AP) components to this connector.
(marked
). When the right REF. VIDEO IN connector
Location and Function of Parts
22
Download from Www.Somanuals.com. All Manuals Search And Download.
is used, the built-in 75 Ω termination switch turns off
automatically.
g COMPONENT VIDEO OUT Y/R−Y/B−Y
connectors (BNC type)
The REF. VIDEO OUT connector outputs a reference
video signal, except when i.LINK is selected in the INPUT
These connectors output analog component video signals
(Y/R−Y/B−Y).
h TIME CODE IN/OUT connectors (BNC type)
Input SMPTE time code (for DSR-1800A) or EBU time
code (for DSR-1800AP) externally generated to the IN
connector.
The OUT connector outputs a time code according to the
operating state of the unit, as follows:
e VIDEO OUT 1 and 2 (SUPER) connectors (BNC
type)
These connectors output analog composite video signals.
set to ON (factory default setting), connector 2 (SUPER)
outputs a signal with superimposed text information.
During playback: the playback time code
During recording: the time code generated by the internal
time code generator or the time code input to the TIME
CODE IN connector. When the EE OUT PHASE menu
f S VIDEO OUT connector (4-pin)
This connector outputs an S-video signal with separated Y
(luminance) and C (chroma: 3.58 MHz for DSR-1800A or
4.43 MHz for DSR-1800AP) components.
B Digital signal input/output section (optional DSBK-1801 board required)
DV IN/OUT
a
DV IN/OUT connector
SDI
OUT
DIGITAL AUDIO(AES/EBU)
CH-3/4
CH-3/4
CH-1/2
CH-1/2
OUT
IN
IN
5 DIGITAL AUDIO (AES/EBU) OUT connectors
4 DIGITAL AUDIO (AES/EBU) IN connectors
3 SDI OUT connectors
2 SDI IN and active through output connectors
a
DV IN/OUT connector (6-pin IEEE-1394)
• When you connect this unit to another device with a 6-
pin DV connector, always power the other device off and
unplug its power cord from the power output before
connecting or disconnecting the i.LINK cable (DV
cable). If you connect or disconnect the cable with the
power cord still plugged in, power from the DV
connector may flow into this unit, possibly damaging
this unit.
This i.LINK-compatible connector inputs and outputs
digital video and audio signals in DV format.
Notes
1
1
• When searching at speeds in the range + / to + / or
2
30
1
1
− / to − / times normal speed, the audio signal output
2
30
from this connector and monitored on external
equipment may sound differently from the audio signal
played back on this unit.
• When you connect this unit to another device with a 6-
pin DV connector, make the connection to the 6-pin DV
Location and Function of Parts
23
Download from Www.Somanuals.com. All Manuals Search And Download.
connector on the other device before making the
connection to this unit.
d DIGITAL AUDIO (AES/EBU) IN connectors
(BNC type) (optional DSBK-1801 SDI/AES/EBU
Input/Output Board required)
b SDI (Serial Digital Interface) IN (input) and active
through output connectors (BNC type) (optional
DSBK-1801 SDI/AES/EBU Input/Output Board
required)
Input digital video and audio signals in SDI format to the
left-hand connector. The right-hand connector is for an
active-through connection.
Input digital audio signals in AES/EBU format to these
connectors.
The left-hand connector (CH-1/2) is for audio channels 1
and 2, and the right-hand connector (CH-3/4) is for audio
channels 3 and 4.
e DIGITAL AUDIO (AES/EBU) OUT connectors
(BNC type) (optional DSBK-1801 SDI/AES/EBU
Input/Output Board required)
These connectors output digital audio signals in AES/EBU
format.
c SDI (Serial Digital Interface) OUT connectors
(BNC type) (optional DSBK-1801 SDI/AES/EBU
Input/Output Board required)
Output SDI-format digital video and audio signals. The
same signals are output from both connectors.
The left-hand connector (CH-1/2) is for audio channels 1
and 2, and the right-hand connector (CH-3/4) is for audio
channels 3 and 4.
C Analog audio signal input/output section
c AUDIO OUT CH-1 to CH-4 connectors
a AUDIO IN LEVEL/600 Ω switches
LEVEL
LEVEL
LEVEL
LEVEL
LOW
OFF
HIGH
ON
LOW
OFF
HIGH
ON
LOW
OFF
HIGH
ON
LOW
OFF
HIGH
ON
MONITOR OUT
AUDIO
AUDIO IN
AUDIO OUT
600
Ω
600
Ω
600
Ω
600
Ω
CH-1
CH-2
CH-3
CH-1
CH-2
CH-3
CH-4
CH-4
b AUDIO IN CH-1 to CH-4 connectors
d AUDIO MONITOR OUT connector
a AUDIO IN LEVEL/600 Ω switches
Set these switches for each channel as shown in the
following table, according to the audio input levels to the
AUDIO IN CH-1 to CH-4 connectors and the required
impedance.
b AUDIO IN CH-1 (channel 1) to CH-4 connectors
(XLR 3-pin, female)
Use these connectors to connect separate channels of
analog audio input from a player VCR or other external
audio equipment.
You can switch the audio input level setting with the
Settings of the AUDIO IN LEVEL/600 Ω switches
Audio input
Level
Switch setting
c AUDIO OUT CH-1 (channel 1) to CH-4 connectors
(XLR 3-pin, male)
These connectors output channel-1 to channel-4 analog
Impedance
−60 dBu
(microphone input)
High impedance LOW-OFF
(left position)
(about 20 kΩ)
audio signals, respectively.
a)
High impedance HIGH-OFF
It is possible to use the AUDIO OUT CH-3 and AUDIO
OUT CH-4 connectors for audio monitor output for
channels 1 and 2, respectively (use the OUTPUT CH3/4
+4/0/−3 /−6 dBu
(middle
position)
(about 20 kΩ)
(line audio input)
a)
HIGH-ON
(right position)
600 Ω
+4/0/−3 /−6 dBm
(line audio input)
d AUDIO MONITOR OUT connector (RCA phono
jack)
a) Selectable on DSR-1800AP only
This connector outputs audio signals for monitoring. The
audio signals to be output from this connector can be
Location and Function of Parts
24
Download from Www.Somanuals.com. All Manuals Search And Download.
selected with the MONITOR SELECT switches on the
menu control panel.
D External device connectors
VIDEO CONTROL
a VIDEO CONTROL connector
REMOTE
b REMOTE connector
a VIDEO CONTROL connector (D-sub 15-pin)
For remote control of the internal digital video processor,
connect an optional remote control unit to this connector.
b REMOTE connector (D-sub 9-pin)
Use the optional 9-pin remote cable to connect an editing
controller that supports this unit, or a VCR that supports
editing with two units (DSR-2000A/2000AP, etc.), to
connect those devices to this unit for remote control.
Location and Function of Parts
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Location and Function of Parts
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording and Playback Chapter
2
Usable Cassettes
This unit can use the DVCAM cassettes listed below.
Model name
Size
PDV-34*/64*/94*/124*/184*
PDVM-12*/22*/32*/40*
Standard size
Mini size
The * in each model name is actually “ME” (indicating that a cassette memory
is contained), or “N” (indicating that no cassette memory is contained).
The numbers in each model name indicate the maximum recording/playback
time (in minutes) for each model. For example, the PDV-184ME has a
maximum recording/playback time of 184 minutes.
Cassettes usable for playback only
Large- and medium-size DVCPRO (25M) cassettes are usable for playback
only.
Notes
• If you insert an incorrect type of cassette, it will be automatically ejected.
• Although this unit can use DV series consumer cassettes, video or audio noise
may occur on some tapes.
For reliable playback, editing, recording, and storage, use DVCAM cassettes.
• Cassettes that have been recorded by a DV-format recorder can be played
back on this unit but cannot be used for recording at editing operation. When
you insert such a cassette into this unit, the NOT EDITABLE indicator lights
up in the display section on the front panel of this unit.
Usable Cassettes
27
Download from Www.Somanuals.com. All Manuals Search And Download.
DVCAM cassettes
The following figure illustrates the DVCAM cassettes.
REC/SAVE switch
For details of this switch, see “Preventing accidental
Mini size
Standard size
Cassette memory
Notes on using cassettes
• Before storing the cassette for a long period of time, rewind the tape to the
beginning and be sure to put the cassette in its storage case, preferably on end
instead of flat on its side.
Storing a cassette in any other condition (not rewound, out of its case, etc.)
may cause the video and audio contents to become damaged over time.
• If the cassette memory connector (contact point) becomes dirty, connection
problems may occur, causing a loss of functions. Remove away any dust or
dirt from this area before using the cassette.
• If the cassette is dropped on the floor or otherwise receives a hard impact, the
tape may become slackened and may not record and/or play back correctly.
For information about how to check the tape for slack, see the next section.
Checking the tape for slack
Using a paper clip or a similar object, turn the reel gently in the direction shown
by the arrow. If the reel does not move, there is no slack. Insert the cassette into
the cassette compartment, and after about 10 seconds take it out.
Paper clip, etc.
Reel
Usable Cassettes
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Preventing accidental erasure
Set the REC/SAVE switch on the cassette to SAVE to prevent accidental
erasure of recorded contents.
REC/SAVE switch
Set to SAVE
REC
SAVE
To enable re-recording
Set the REC/SAVE switch to REC.
When this switch is set to SAVE, the unit cannot record on the tape.
Inserting and Ejecting Cassettes
Inserting a cassette
This unit accepts three sizes of cassette: L (standard size), M (medium size:
DVCPRO) and S (mini size). When inserting a cassette in the unit, make sure
its tape window faces upward as shown in the following figure.
Outer guides
Mini size (Insert the cassette into the
middle of the cassette compartment.)
Standard size
Tape window facing upward
Inner guides
Medium size (Align the cassette with
the outer guides, then slide it in over
the inner guides.)
Tape window facing upward
Usable Cassettes
29
Download from Www.Somanuals.com. All Manuals Search And Download.
No double insertion of cassettes
When you insert a cassette, the orange lock-out plate appears in the cassette
compartment to prevent double insertion.
Ejecting a cassette
Press the EJECT button.
OVER
OVER
OVER
OVER
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
INPUT
V:SDTI
SDTI
-R,B
i.LINK
VIDEO COMPOSITE
CH11/2
Y
S
VIDEO SDI SG
-12
-20
1
-12
-20
1
-12
-20
1
-12
-20
1
0
-1
-2
1
0
-1
-2
2
0
-1
-2
3
0
-1
-2
4
ANALOG AES/EBU
ANALOG AES/EBU
SDI SG
SDI SG
AUDIO
CH23/4
-30
-40
-30
-40
-30
-40
-30
-40
-60
-60
-60
-60
PB FS
48k44.1k32k REC MODE
2CH4CH
EJECT button
Usable Cassettes
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
This section describes the necessary settings and operations to perform
recording on this unit. The same settings and operations apply whether you are
using the unit as part of an editing system, for dubbing, or as a stand-alone
recorder.
For the necessary connections for recording and the settings not covered in this
Settings for Recording
Player (DSR-1600A/1600AP, etc.)
OVER
OVER
OVER
OVER
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
-12
-20
1
-12
-20
1
-12
-20
1
-12
-20
1
0
-1
-2
1
0
-1
-2
2
0
-1
-2
3
0
-1
-2
4
-30
-40
-30
-40
-30
-40
-30
-40
-60
-60
-60
-60
PB FS
48k44.1k32k
2
1
Video monitor
Audio level meters
Inputselection/audiomode
display section
REMOTE button
OVER
OVER
OVER
OVER
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
INPUT
V:SDTI
SDTI
-R,B
i.LINK
VIDEO COMPOSITE
CH11/2
Y
S
VIDEO SDI SG
-12
-20
1
-12
-20
1
-12
-20
1
-12
-20
1
0
-1
-2
1
0
-1
-2
2
0
-1
-2
3
0
-1
-2
4
ANALOG AES/EBU
ANALOG AES/EBU
SDI SG
SDI SG
AUDIO
CH23/4
-30
-40
-30
-40
-30
-40
-30
-40
-60
-60
-60
-60
PB FS
48k44.1k32k REC MODE
2CH4CH
3
Recorder (DSR-1800A/1800AP)
7
A
B
MARK
5 6
4
Note
When controlling this unit from an editing control unit connected to the
1 Power on the video monitor, then set its input switches according to the
signals input from this unit.
2 Set up the player to play back a tape.
Recording
31
Download from Www.Somanuals.com. All Manuals Search And Download.
For details, refer to the operating instructions for the player.
3 Power on this unit by pressing on the side of the POWER switch.
4 When the REMOTE button is not lit (the external editing control unit is not
used), use the COUNTER SEL button to select the type of time data to be
used.
Each press of this button cycles through three options: COUNTER (CNT
value), TC (time code), and U-BIT (user bit data). The time data type
indicator for each option lights as it is selected.
Selected time data
Count value of the time counter
Time code
Time data type indicator
COUNTER
TC
User bit data
U-BIT
When the REMOTE button is lit, selection of the time data type is carried
out at the editing control unit.
5 Select the formats of video and audio input signal to be recorded.
Use the buttons in the INPUT SELECT section to select the desired signal
formats. Each selection is shown by a lit indicator in the input selection/
audio mode display section.
Video input signal
(input connector)
Corresponding button Lit indicator in the
in the INPUT SELECT input selection/audio
section
mode display section
Composite signal
(VIDEO IN)
VIDEO IN
COMPOSITE in VIDEO
group
Separated Y/C signal
(S VIDEO IN)
VIDEO IN
VIDEO IN
S VIDEO in VIDEO
group
Component signal
(COMPONENT VIDEO
IN)
Y−R, B in VIDEO group
a)
SDI signal (SDI IN)
VIDEO IN
SDI in VIDEO group
i.LINK-compatible digital SDTI/i.LINK
video signal in DV format
i.LINK
( DV IN/OUT)
Internal test video signal VIDEO IN
SG in VIDEO group
a) The indicator does not light even if you press the corresponding button in the INPUT SELECT
section unless the required optional digital input/output board (DSBK-1801) is installed.
Audio input signal
(input connector)
Corresponding button Lit indicator in the
in the INPUT SELECT input selection/audio
section
mode display section
Analog signal
(AUDIO IN CH-1 to CH-
4)
CH-1,1/2 and CH-2,3/4 ANALOG in AUDIO
group
a)
AES/EBU signal
(DIGITAL AUDIO (AES/
EBU) IN)
CH-1,1/2 and CH-2,3/4
AES/EBU in AUDIO
group
a)
SDI signal (SDI IN)
CH-1,1/2 and CH-2,3/4
SDI in AUDIO group
i.LINK-compatible digital SDTI/i.LINK
audio signal in DV format
i.LINK
( DV IN/OUT)
Recording
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio input signal
(input connector)
Corresponding button Lit indicator in the
in the INPUT SELECT input selection/audio
section
mode display section
Internal test audio signal CH-1,1/2 and CH-2,3/4 SG in AUDIO group
a) The indicator does not light even if you press the corresponding button in the INPUT SELECT
section unless the required optional digital input/output board (DSBK-1801) is installed.
Caution
Once you have started recording, you cannot change the input signal
selection.
6 Select the audio mode.
Select either two-channel mode (2CHANNEL) or four-channel mode
corresponding indicator lights in the REC MODE display.
Audio mode
Lit indicator in the REC MODE display
2-channel mode
4-channel mode
2CH
4CH
Cautions
• In the DVCAM format, there are two audio recording modes, with either
two channels at 48 kHz or four channels at 32 kHz. It is not possible to
select other modes (for example with four channels at 48 kHz).
• During audio editing, if a signal used in assemble or insert editing is in a
different mode from the base tape, the signals will be discontinuous at the
edit points, and correct editing will not be obtained. For this reason, audio
editing between different modes is inhibited on this unit.
For smooth editing operations, check the audio recording mode of the
base tape beforehand.
• Once you have started recording, you cannot change the audio mode
selection.
• If on a tape there is a point where the audio mode is switched, it is not
possible to carry out insert editing over a section including that point.
7 Use the AUDIO INPUT LEVEL control knobs to adjust audio input levels.
Watching the audio level meter, adjust the level so that the meter does not
indicate higher values than 0 dB when the audio signal is at its maximum.
When the level exceeds 0 dB, the OVER indicator lights.
The factory-preset audio recording level is −20 dB (DSR-1800A) or −18 dB
(DSR-1800AP). This setting can be changed using the LEVEL SELECT
Recording
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Procedure
This section describes the procedure to perform recording on this unit, showing
an example session in which playback signals coming from a player VCR will
be recorded on the tape loaded in the unit.
1
OVER
OVER
OVER
OVER
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
INPUT
V:SDTI
SDTI
-R,B
i.LINK
VIDEO COMPOSITE
CH11/2
Y
S
VIDEO SDI SG
-12
-20
1
-12
-20
1
-12
-20
1
-12
-20
1
0
-1
-2
1
0
-1
-2
2
0
-1
-2
3
0
-1
-2
4
ANALOG AES/EBU
ANALOG AES/EBU
SDI SG
SDI SG
AUDIO
CH23/4
-30
-40
-30
-40
-30
-40
-30
-40
-60
-60
-60
-60
PB FS
48k44.1k32k REC MODE
2CH4CH
REMOTE button
Recorder
(DSR-1800A/1800AP)
2
OVER
OVER
OVER
OVER
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
-12
-20
1
-12
-20
1
-12
-20
1
-12
-20
1
-1
-2
1
0
-1
-2
2
0
-1
-2
3
-1
-2
4
-30
-40
-30
-40
-30
-40
-30
-40
-60
-60
-60
-60
PB FS
48k44.1k32k
Player
(DSR-1600A/1600AP, etc.)
3
Note
When controlling this unit from an editing control unit connected to the
REMOTE connector of this unit, press the REMOTE button to turn it on. When
not, turn off the button.
Recording
34
Download from Www.Somanuals.com. All Manuals Search And Download.
1 After checking the following items, hold the cassette with the tape window
facing upward, then insert it into the recorder (this unit) as illustrated on
.
Item to check
See section
of the cassette is set to REC.
Check for tape slack.
not shown in the time counter display.
The cassette is automatically drawn into the unit and the tape is wound
round the head drum. The tape is stationary while the head drum rotates, and
the STOP button lights.
If the REC INHIBIT indicator lights:
It indicates that the REC/SAVE switch of the loaded cassette has been set
to SAVE. Press the EJECT button in the tape transport control section to
remove the cassette, then set the REC/SAVE switch to REC and reload the
cassette.
Note
When ejecting and loading cassettes, make sure that the unit has been
powered on.
2 Hold down the REC button and press the PLAY button.
This puts the unit into recording mode, and the tape starts moving.
3 Press the PLAY button on the player.
The player starts the playback operation, at which point this unit starts
recording the input playback signals.
Cautions
• Once you have started recording, you cannot change the audio mode
selection.
• If on a tape there is a point where the audio mode is switched, it is not
possible to carry out insert editing over a section including that point.
Recording
35
Download from Www.Somanuals.com. All Manuals Search And Download.
If the following indicators light when a cassette is loaded
Indicator
It means:
Cassette memory indicator The loaded cassette contains a cassette memory.
ClipLink indicator
There is ClipLink log data stored in the cassette
memory on the loaded cassette.
Caution
With such a cassette, carrying out recording destroys
the ClipLink log data.
NOT EDITABLE indicator
The recording format of the tape is “DV,” or a
DVCPRO tape is inserted.
Replace the tape with one that has been recorded in
DVCAM format.
The audio recording mode selected on this unit does
not coincide with that of the tape.
• When your current purpose is recording, you can
use the tape as it is.
• When your current purpose is editing, set the unit
for the same audio recording mode as with the
tape.
For more details, see “Troubleshooting” on page
98.
To perform the following operations
Operation
Do this:
Stop recording.
Press the STOP button.
The unit enters stop mode, and will automatically
switch to standby off mode after the time period set
Remove the cassette.
Press the EJECT button.
After a few seconds, the tape is unwound from the
head drum and the cassette is automatically ejected.
If a CNT value is shown on the time counter display
(assuming the time data type indicator “COUNTER”
is lit), the CNT value is reset.
Inhibit the unit from
outputting text information to OFF.
(time data, operation mode
indications, etc.) to the
video monitor.
Change the time period
before the unit switches
from stop mode to standby
off mode.
Change the setting of the STOP TIMER menu item
Recording
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
This section describes the settings and operations necessary to perform playback
on this unit. The same settings and operations apply whether you are using the
unit as part of an editing system, for dubbing, or as a stand-alone player VCR.
For the necessary connections for playback and the settings not covered in this
Settings for Playback
Video monitor
2
Player (DSR-1800A/1800AP)
OVER
OVER
OVER
OVER
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
INPUT
V:SDTI
SDTI
-R,B
i.LINK
VIDEO COMPOSITE
CH11/2
Y
S
VIDEO SDI SG
-12
-20
1
-12
-20
1
-12
-20
1
-12
-20
1
0
-1
-2
1
0
-1
-2
2
0
-1
-2
3
0
-1
-2
4
ANALOG AES/EBU
ANALOG AES/EBU
SDI SG
SDI SG
AUDIO
CH23/4
-30
-40
-30
-40
-30
-40
-30
-40
-60
-60
-60
-60
PB FS
48k44.1k32k REC MODE
2CH4CH
1
1 Power on this unit by pressing on the side of the POWER switch.
2 Power on the video monitor and set its switches as shown below.
Switch
Setting
75 Ω termination switch
Input switch
ON (or attach a 75 Ω terminator.)
Set according to the type of input signal from this
unit.
Playback
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback Procedure
1
OVER
OVER
OVER
OVER
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
INPUT
V:SDTI
SDTI
-R,B
i.LINK
VIDEO COMPOSITE
CH11/2
Y
S
VIDEO SDI SG
-12
-20
1
-12
-20
1
-12
-20
1
-12
-20
1
0
-1
-2
1
0
-1
-2
2
0
-1
-2
3
0
-1
-2
4
ANALOG AES/EBU
ANALOG AES/EBU
SDI SG
SDI SG
AUDIO
CH23/4
-30
-40
-30
-40
-30
-40
-30
-40
-60
-60
-60
-60
PB FS
48k44.1k32k REC MODE
2CH4CH
REMOTE button
2
Note
When controlling this unit from an editing control unit connected to the
turning it on. When not, turn off the button.
1 Insert a cassette.
The cassette is automatically drawn into the unit. The STOP button will
light, and a few seconds later a still image will appear on the monitor screen.
2 Press the PLAY button.
This starts the playback operation. When the tape is played back all the way
to the end, the unit automatically rewinds it and then stops.
If the following indicators light when a cassette is loaded
Indicator
It means:
Cassette memory indicator The loaded cassette contains a cassette memory.
ClipLink indicator
There is ClipLink log data stored in the cassette
memory on the loaded cassette.
NOT EDITABLE indicator
The tape was recorded in the DV format, or a
DVCPRO tape is inserted.
You cannot use it as a recording tape for editing.
To perform the following operations
Operation
Do this:
Stop playback.
Press the STOP button.
The unit enters stop mode, and will automatically
switch to standby off mode after the time set with the
Adjust the audio playback Use the audio level control on the monitor.
level.
Playback
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Do this:
Play back in shuttle mode Press the SEARCH button or search dial to light the
while monitoring the video. SHUTTLE indicator in the display section, then rotate
the search dial.
Playback is carried out at the speed determined by
the angular position of the search dial.
The maximum speed for shuttle playback can be
changed using the SHUTTLE menu item (see page
63).
Play back in jog mode while Press the SEARCH button or search dial to light the
monitoring the video.
JOG indicator in the display section, then rotate the
search dial.
Playback is carried out at the speed according to the
speed of the search dial rotation. The playback
speed range is 1 times normal speed by factory
default.
The search dial has no detents.
Inhibit the unit from
outputting text information to OFF.
(time data, operation mode
indications, etc.) to the
video monitor.
Remove the cassette.
Press the EJECT button.
If a CNT value is shown on the time counter display,
the CNT value is reset.
Disable the automatic
rewind function.
DISABLE.
Change the time period
before the unit switches
from stop mode to standby
off mode.
Change the setting of the STOP TIMER menu item
Playback
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeat Playback—Automatic Cyclical Playback
Proceed as follows to perform automatic cyclical playback of recording (repeat
playback) between selected start and end points.
1 Set the desired repeat start and end points with the REPEAT FUNCTION
You can set points A and B as start and end points by following the
procedure described in the next section.
The REPEAT indicator lights.
3 Press the SET (YES) button to save the new setting and close the menu.
4 Press the PLAY button.
The unit repeats playback between the repeat start and end points set in step
1.
Setting Points A and B for Repeat Playback
You can set the repeat playback start point (point A) and end point (point B) by
using the current tape position or inputting time code values.
To perform repeat playback after setting points A and B, press the PLAY button
when the REMOTE button is off. When the DSRM-10 Remote Control Unit is
connected to the CONTROL S connector on the front panel, you can also start
repeat playback by pressing its PLAY button with the REMOTE button of this
unit off.
Setting the current tape position as point A or B
Proceed as follows to set the current tape position as point A or B for repeat
playback.
Buttons used for
setting the current
tape position as
point A
A
B
MARK
Buttons used for setting the
current tape position as
point B
In the following explanation of how to set points A and B for repeat
playback, these three buttons are referred to as the KA button, Bk
button, and SET (YES) MARK button, respectively.
Playback
40
Download from Www.Somanuals.com. All Manuals Search And Download.
While holding down the SET (YES) MARK button on the menu control panel,
press the KA or Bk button. The time code value of the current tape
position is set as point A or B, and a message “A set” or “B set” is displayed for
0.5 second in the time counter display.
Once set, the point A or B time code value is held in the non-volatile memory
of the unit until changed. It is not lost when the unit is powered off.
Note
When setting point A or B, you can only use a time code value. Even when
COUNTER is selected with the COUNTER SEL button, you cannot use a CNT
value to set point A or B.
To check the point A or B time code value
Press the KA or Bk button on the menu control panel. While the button is
held down, the point A or B time code value is displayed on the monitor and in
the time counter display.
If you hold down the KA and Bk buttons simultaneously, the value shown
is the point B time code value minus the point A time code value. If the point A
time code value is greater than the point B time code value, a minus sign (−) is
shown before the value.
Inputting time code values for points A and B
Using the following procedure, you can modify the time code value for point A
or B.
1,15
8,11 12 2,3,4,6,10,11
A
B
MARK
5,7,9,12 13
1 Press the MENU button.
The following menu display appears.
SYSTEM MENU
SETUP MENU
Setup menu
Time counter display
AUTO FUNCTION
HOURS METER
Monitor screen
Playback
41
Download from Www.Somanuals.com. All Manuals Search And Download.
2 With “SETUP MENU” selected, press the Bk button.
The display changes as follows.
SETUP MENU
Operational
OPERATIONAL FUNCTION
DISPLAY CONTROL
Time counter display
TIME CODE
SETUP BANK OPERATION
MENU GRADE
:BASIC
Monitor screen
3 With “OPERATIONAL FUNCTION” selected, press the Bk button.
The display changes as follows.
SETUP MENU
>REP FUNC
OPERATIONAL FUNCTION
REPEAT FUNCTION
Time counter display
AUTO EE SELECT
LOCAL ENABLE :STP&EJ
Monitor screen
4 With “REPEAT FUNCTION” selected, press the Bk button.
The contents of the REPEAT FUNCTION menu item are displayed.
SETUP MENU
>> REPEAT MD
OPERATIONAL FUNCTION
REPEAT FUNCTION
Time counter display
:OFF
REPEAT MODE
REPEAT TOP
REPEAT END
A PRESET
:
T.TOP
V.END
:
B PRESET
Monitor screen
Playback
42
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Press the j button to select “REPEAT TOP.”
SETUP MENU
>> REP TOP
Time counter display
OPERATIONAL FUNCTION
REPEAT FUNCTION
REPEAT MODE
REPEAT TOP
REPEAT END
A PRESET
:OFF
:T.TOP
:V.END
B PRESET
Monitor screen
6 Press the Bk button.
The display changes as follows.
SETUP MENU
OPERATIONAL FUNCTION
REPEAT FUNCTION
>>> Tape top
Time counter display
:T.TOP
REPEAT TOP
* TAPE TOP
A POINT
:V.END
Monitor screen
7 Press the j button to select “A POINT.”
SETUP MENU
OPERATIONAL FUNCTION
REPEAT FUNCTION
>>> A point
Time counter display
REPEAT TOP
:T.TOP
* TAPE TOP :V.END
A POINT
Monitor screen
Playback
43
Download from Www.Somanuals.com. All Manuals Search And Download.
8 Press the KA button.
The display changes as follows.
SETUP MENU
OPERATIONAL FUNCTION
REPEAT FUNCTION
>> REP TOP
Time counter display
:OFF
.
REPEAT MODE
REPEAT TOP
REPEAT END
A PRESET
A
:
V.END
B PRESET
Monitor screen
9 Press the j button to select “A PRESET.”
SETUP MENU
OPERATIONAL FUNCTION
REPEAT FUNCTION
>> A preset
Time counter display
:OFF
.
REPEAT MODE
REPEAT TOP
REPEAT END
A PRESET
A
:
V.END
B PRESET
Monitor screen
10Press the Bk button.
The A PRESET MODE screen appears. The time code value of the current
point A is displayed below the screen title.
A PRESET MODE
A 00:00:00:00
INC/DEC : ( )( )KEY
SHIFT : ( )( )KEY
CLEAR : RESET KEY
DATA SAVE :
SET KEY
TO MENU : MENU KEY
Monitor screen
11Use the KA or Bk button to select the digit in the time code value
display that you want to change.
Each press of the button causes the digit to the left or right to begin flashing.
Holding the button down moves the flashing digit continuously.
If you want to clear the time code value, press the RESET (NO) button. The
value is cleared to 00:00:00:00, and the leftmost digit begins flashing.
Playback
44
Download from Www.Somanuals.com. All Manuals Search And Download.
12Press the J or j button to increment or decrement the value of the flashing
digit.
Each press of the button increments or decrements the value. Holding the
button down increments or decrements the value continuously. To change
other digits, return to step 11.
MARK
13Press the SET (YES)
button to confirm the defined value.
The message “NOW SAVING...” is displayed on the monitor screen and
“Saving...” is shown in the time counter display while the new setting is
being saved in memory.
Caution
The new setting may be lost if you power off the unit during the saving
operation. Wait until the saving operation is completed before powering the
unit off.
If you want to discard the changed value
Press the MENU button instead of pressing the SET (YES) MARK button
to return to the menu display, then press the MENU button again to end the
menu operation without saving the changed value into memory.
After the saving operation is completed, the monitor screen and time
counter display return to the REPEAT FUNCTION setting display as
shown in step 9.
14To set point B, refer to steps 5 to 13. (Select “REPEAT END” in step 5, “B
POINT” in step 7, and “B PRESET” in step 9.)
15Press the MENU button to close the menu.
Cuing Up to Any Desired Position Set as Point A or B
You can set any desired tape position as point A or B and cue up to the set point
when required. To cue up to point A or B, holding down the KA or Bk
button on the menu control panel, press the REW button in the tape transport
control section.
For the methods of setting points A and B, see “Setting Points A and B for
Playback
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Convenient Functions
for Editing Operation Chapter
3
Use the DISPLAY CONTROL menu items (see page 65)
to select the information displayed and the character type
and position of the indications.
Setting the Time Data
When you set the SUB STATUS menu item (see page 65)
to other than OFF, you can also display supplementary
status information on the monitor screen such as editing
mode settings and the operating mode of the internal time
code generator.
This unit is provided with the following functions related
to time data.
• Display and reset CNT value
• Set, display, record, and play back SMPTE/EBU time
code and user bit data
• Set, display, record, and play back VITC
For details of supplementary status information, see
The unit can output the time code read from the tape as an
analog (LTC) signal while in normal-speed playback
mode, and receive an external analog time code (LTC)
signal.
Note
The unit outputs no signal from the TIME CODE OUT
connector unless it is in normal-speed playback mode.
The following explains how to use these functions.
Displaying Time Data and Operation
Mode Indications
Time data and operation mode indications can be
displayed on the monitor screen.
Time data can also be displayed in the time counter display
on this unit.
To view time data and operation mode
indications on the monitor screen
ON (factory default setting).
The time data and the indication of the current operation
mode are superimposed on the video signal that is being
output from the VIDEO OUT 2 (SUPER) connector, and
can be viewed on the monitor screen.
Setting the Time Data
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitor screen contents
The contents of the monitor screen are shown below.
C Drop frame indication for time code generator
(for DSR-1800A only)
.
:
Drop frame mode (factory default setting)
Non-drop frame mode
A Time data type
Time data
D VITC field indication
B Drop frame indication
a)
for time code reader
(blank)
Display fields 1 and 3.
Display fields 2 and 4.
C Drop frame indication
*
for time code
a)
generator
D VITC field
E DSR-1800A/1800AP operation mode
indication
.
.
T C R
0 0
:
0 4
4 7
0 7
*
Display
Operation mode
P L A Y
L O C K
CASSETTE OUT
THREADING
UNTHREADING
STANDBY OFF
T. RELEASE
STOP
Cassette is not loaded.
Tape loading
E DSR-1800A/1800AP operation mode
Tape unloading
a) This character (.) can appear on the DSR-1800A only. The
character to appear in these two columns is always a colon
( : ) on the DSR-1800AP.
Standby off mode
Tape tension released
Stop mode
A Time data type
The following time data type indications are displayed.
F. FWD
Fast forward mode
REW
Rewind mode
Indication
CNT
Description
PREROLL
PLAY
Preroll mode
Count value of the time counter
Playback mode (servo unlocked)
Playback mode (servo locked)
Temporary stop of playback
Record mode (servo unlocked)
Record mode (servo locked)
Temporary stop of recording
Edit mode (servo unlocked)
Edit mode (servo locked)
Still picture in jog mode
Jog mode in forward direction
Jog mode in reverse direction
Shuttle mode
TCR
Time code data from time code reader
(factory default setting)
PLAY LOCK
PLAY-PAUSE
REC
UBR
User bit data from time code reader
a)
TCR.
Time code data from VITC reader
REC LOCK
REC-PAUSE
EDIT
a)
UBR.
User bit data from VITC reader
TCG
UBG
Time code data from time code generator
User bit data from time code generator
EDIT LOCK
JOG STILL
JOG FWD
JOG REV
SHUTTLE (Speed)
AUTO EDIT
PREVIEW
REVIEW
b)
Time code data from time code reader. The
asterisk indicates an interpolation by the time
code reader to make up for the time code
data not correctly read from the tape.
T*R
b)
User bit data from the time code reader. The
asterisk indicates that last data is retained by
the time code reader, as the new data has
not been read correctly from the tape.
U*R
Automatic editing mode
Preview mode
Review mode
a) You can switch between TC and VITC using the TC SELECT menu item
b) “*” is displayed when data cannot be read in correctly.
B Drop frame indication for time code reader (on
DSR-1800A only)
.
:
Drop frame mode (factory default setting)
Non-drop frame mode
Setting the Time Data
48
Download from Www.Somanuals.com. All Manuals Search And Download.
To reset the CNT value
Press the RESET (NO) button on the menu control panel.
This resets the CNT value to 0:00:00:00.
To display the desired time data in the time
counter display
Note
During playback, if the recording on the tape includes
discontinuities, the counter may operate incorrectly at the
corresponding points.
Time data type indicators
Time counter display
Using the Internal Time Code
Generator
OVER
OVER
OVER
OVER
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
INPUT
V:SDTI
SDTI
-R,B
i.LINK
VIDEO COMPOSITE
CH11/2
Y
S
VIDEO SDI SG
-12
-20
1
-12
-20
1
-12
-20
1
-12
-20
1
0
-1
-2
1
0
-1
-2
2
0
-1
-2
3
0
-1
-2
4
ANALOG AES/EBU
ANALOG AES/EBU
SDI SG
SDI SG
AUDIO
CH23/4
-30
-40
-30
-40
-30
-40
-30
-40
-60
-60
-60
-60
PB FS
48k44.1k32k REC MODE
2CH4CH
You can set the initial time code value before recording the
time code generated by the internal time code generator
onto a tape. In addition, you can use the user bits to record
such data as the date, time, scene number, reel number, or
other useful information.
COUNTER SEL button
When an external time code generator is connected to the
TIME CODE IN connector, the internal time code
generator can be locked to (synchronized with) an external
time code.
A
B
MARK
To set the initial time code value and user
bit data
Open the door on the lower part of the front panel, and
press the COUNTER SEL button.
Each press of this button cycles through three options:
CNT value, time code, and user bit data. The time data type
indicator for each option lights as it is selected.
1
Time data
type
indicator
Time data shown in the time counter
display
A
B
MARK
COUNTER
TC
CNT (count value of the time counter)
Time code (when recording, the time code is
generated by the internal time code
generator; when playing back, the time code
is read from the tape.)
2 3
4,5,6 7
U-BIT
User bit data (when recording, the user bit
data is according to the most recent settings;
when playing back, the user bit data is read
from the tape.)
1 Press the COUNTER SEL button to light the time data
type indicator “TC” or “U-BIT.”
Note
TC: To set the initial time code value.
U-BIT: To set user bit data
When the REMOTE button on the front panel is lit, the
COUNTER SEL button does not operate while the tape is
moving. In such cases, use the external equipment
connected to the REMOTE connector on the rear panel to
select the time data.
The current time code value or user bit data is shown
in the time counter display.
Setting the Time Data
49
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Press the SET (YES) button.
shown below.
The message “NOW SAVING...” appears on the
monitor screen, “Saving...” appears in the time counter
display, and the new settings are stored in memory.
After this saving operation is completed, the monitor
screen and the time counter display return to their
usual status.
Menu item
TC MODE
RUN MODE
Setting
“INT PRESET”
“FREE RUN” or “REC RUN”
Normally “ON (DF)”
DF MODE
(for DSR-1800A only)
Note
The set data may be lost if you power off the unit while
the above saving operation is in progress. Wait until
the saving operation is completed before powering off.
3 Press the TC PRESET button on the menu control
panel.
The current setting is shown on the monitor screen and
in the time counter display on the front panel. The
leftmost digit keeps flashing.
One of the following menu screens is displayed on the
monitor depending on the setting made in step 1.
Advancement of internal time code
generator
The internal time code generator can advance in either of
two modes, which can be set with the RUN MODE menu
TC PRESET MODE
TCG 00:00:00:00
UB PRESET MODE
UBG 00:00:00:00
FREE RUN: Advancement starts when the data saving
operation is completed.
REC RUN: Advancement starts when recording starts and
stops when recording stops.
INC/DEC : ( )( )KEY
SHIFT : ( )( )KEY
CLEAR : RESET KEY
INC/DEC : ( )( )KEY
SHIFT : ( )( )KEY
CLEAR : RESET KEY
To set the current time as the initial time
code value
DATA SAVE :
SET KEY
DATA SAVE :
SET KEY
ABORT : TC PRESET KEY
ABORT : TC PRESET KEY
66) to FREE RUN, then set the current time (format:
HH:MM:SS:FF = hours: minutes:seconds:frame number)
in step 3 and subsequent steps.
Initial time code value setting
screen
User bit setting screen
Note
If you press the TC PRESET button while CNT value
is being displayed, the message “COUNTER MODE
IS SELECTED.” will appear on the monitor screen
and “CNT mode!” will appear in the time counter
display on the front panel. If this happens, press the
COUNTER SEL button to light the time data type
indicator “TC” or “U-BIT.”
Synchronizing Internal and External
Time Codes
The internal time code generator can be synchronized with
an external time code (LTC) input to this unit.
To synchronize the internal time code to
external time code
Input an external time code (LTC) signal to the TIME
CODE IN connector, then set the TC MODE menu item
(see page 66) to EXT REGEN.
The internal time code generator locks onto the external
time code and starts advancing. Once the internal time
code generator has been synchronized in this way, you can
disconnect the external time code input and this unit will
maintain the synchronized time code.
4 Use the K and k buttons to move the flashing digit
to the value to be changed.
5 Use the J and j buttons to change the value of the
flashing digit.
Enter hexadecimal values (0 to 9, A to F) when setting
user bit data.
6 Repeat steps 4 and 5 until you have set the desired
values for all digits.
Note
To set a value of 00:00:00:00, simply press the RESET
(NO) button.
When the selected input mode is “i.LINK” (the i.LINK
indicator is lit in the INPUT display), setting the TC
the internal time code generator to automatically
Setting the Time Data
50
Download from Www.Somanuals.com. All Manuals Search And Download.
synchronize with the external time code input to the unit
via the i.LINK interface.
SYSTEM MENU
SETUP MENU
AUTO FUNCTION
HOURS METER
Setup menu
Time counter display
Once an external time code signal has been input, the
internal time code advancement mode and frame count
mode are automatically set as follows:
Advancement mode: FREE RUN
Frame count mode: Same as external time code (drop
frame or non-drop frame)
Monitor screen
To confirm external synchronization
Press the STOP button to put the unit into stop mode, then
press the REC button.
Look at the time counter display and check that the time
code value displayed there matches the external time code
value.
2 Press the J or j button to select “AUTO
FUNCTION.”
SYSTEM MENU
Auto func
Time counter display
SETUP MENU
AUTO FUNCTION
HOURS METER
Rerecording the Time Code—TC
Insert Function
The TC insert function makes it possible to use the internal
time code generator to rewrite time code or user bits when
the time code recorded on a tape is discontinuous.
You can start recording time code from an initial value
Monitor screen
Notes
• Use a tape which is recorded in the DVCAM format.
(You cannot use the TC insert function with a tape
recorded in DV format.)
• The time code recording starts from the current tape
position. Cue the tape up beforehand to the required start
position.
3 Press the k button.
This displays the items in the level 1 of the auto mode
execution menu.
AUTO FUNCTION MENU
i.LINK DUB
i.LINK DUBBING
• If you use a tape on which ClipLink log data is recorded,
the ClipLink log data will be lost.
TC INSERT
Time counter display
A
B
MARK
Monitor screen
1
2,4
3,5
7,8
4 Press the j button to select “TC INSERT.”
1 Open the door on the lower part of the front panel, then
press the MENU button.
Setting the Time Data
51
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTO FUNCTION MENU
i.LINK DUBBING
TC INSERT
TC INSERT
TC insert
Time counter display
Executing
Time counter display
EXECUTING.
TCR 00:00:00:00
UBR 00:00:00:00
ABORT:MENU KEY
Monitor screen
Monitor screen
When the recording ends, the message “TC INSERT
COMPLETED. PUSH THE YES BUTTON.” appears
on the monitor screen and “Completed” appears in the
time counter display.
5 Press the k button.
The following message appears.
TC INSERT
8 Press the SET (YES) button to exit the menu.
Set tape!
Time counter display
INSERT THE TAPE IN
THIS VTR.
ABORT:MENU KEY
Monitor screen
6 Insert the cassette.
A message to confirm the TC insert operation appears.
TC INSERT
TC insert?
Time counter display
START TC INSERT?
START:YES KEY
ABORT:MENU KEY
Monitor screen
To cancel the TC insert operation
Press the MENU button.
7 Press the SET (YES) button.
Time code recording starts from the current tape
position.
Setting the Time Data
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
When controlling this unit from external equipment, be
sure to turn on or off the buttons in the remote control
setting section on the front panel of the unit as shown in the
following table.
High-Speed and Low-
Speed Search—Quickly
and Accurately
Determining Editing
Points
External equipment Buttons in the remote control
setting section
Editing control unit
connected to the
Turn on both the REMOTE and 9PIN
buttons.
REMOTE connector
SIRCS-compatible
remote control unit
connected to the
CONTROL S
Turn off the REMOTE button.
Use the search function to easily locate the desired scene
and to quickly and accurately determine edit points.
connector
When F. FWD/REW under the AUTO EE SELECT menu
can use the F FWD and REW buttons on this unit or
external equipment for high-speed search.
Equipment
connected to the
Turn on both the REMOTE and
i.LINK buttons.
DV IN/OUT
connector
For description on how to carry out search operations via
external equipment, see the operating instructions for the
equipment.
Search Operations via External
Equipment
You can control the unit in the following operation modes
from an editing control unit (PVE-500, etc.) connected to
the REMOTE connector on the rear panel or from a
SIRCS-compatible remote control unit such as the DSRM-
10 connected to the CONTROL S connector on the front
panel.
Search Operations on This Unit
When you perform searching on this unit, be sure to turn
off the REMOTE button on the front panel.
Shuttle: Use this mode to view color video playback at
speeds ranging from 0 to 60 times normal speed in
both directions.
Playing back in jog mode
In jog mode, you can control the speed of playback by the
speed of turning the search dial. The playback speed range
is 1 times normal speed by factory default. The speed
variation range and pattern can be changed with the JOG
Note
When controlling the unit from the DSRM-10 for
shuttle-mode search, the maximum search speed is 16
times normal speed in both directions.
To carry out playback in jog mode, use the following
procedure.
Jog: Use this mode for low-speed search and frame-by-
frame search.
JOG indicator
Digital slow: Use this mode for noise-free color video
1
playback at speeds ranging from 0 to / times normal
speed in both directions.
2
OVER
OVER
OVER
OVER
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
INPUT
V:SDTI
SDTI
-R,B
i.LINK
VIDEO COMPOSITE
CH11/2
Y
S
VIDEO SDI SG
-12
-20
1
-12
-20
1
-12
-20
1
-12
-20
1
0
-1
-2
1
0
-1
-2
2
0
1
-2
3
0
-1
-2
4
ANALOG AES/EBU
ANALOG AES/EBU
SDI SG
SDI SG
AUDIO
CH23/4
-30
-40
-30
-40
-30
-40
-30
-40
-60
-60
-60
-60
PB FS
48k44.1k32k REC MODE
2CH4CH
Still: Use this mode to view a still picture of any field.
Jog audio: Use this mode to monitor the audio at speeds
1
ranging from 1 to / times normal speed in both
30
directions.
1 1,2,3
1 Press the SEARCH button or search dial so that the
JOG indicator in the display section is lit.
High-Speed and Low-Speed Search—Quickly and Accurately Determining Editing Points
Download from Www.Somanuals.com. All Manuals Search And Download.
53
Pressing the search dial toggles between jog mode and
shuttle mode.
normal-speed playback and shuttle playback by pressing
the PLAY and SEARCH buttons alternately.
For intermittent shuttle mode playback, press the STOP
and SEARCH buttons alternately.
2 Turn the search dial in the desired direction at the
speed corresponding to the desired playback speed.
Playback in jog mode starts.
3 To stop playback in jog mode, stop turning the search
dial.
Playing back in shuttle mode
In shuttle mode, you can control the speed of playback by
the angular position of the search dial. The range of
playback speed is 32 times normal speed by factory
default. This can be changed with the SHUTTLE menu
positions of still image and 10 times normal speed.
To carry out playback in shuttle mode, use the following
procedure.
SHUTTLE indicator
OVER
OVER
OVER
OVER
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
INPUT
V:SDTI
SDTI
-R,B
i.LINK
VIDEO COMPOSITE
CH11/2
Y
S
VIDEO SDI SG
-12
-20
1
-12
-20
1
-12
-20
1
-12
-20
1
0
-1
-2
1
0
-1
-2
2
-1
-2
3
0
-1
-2
4
ANALOG AES/EBU
ANALOG AES/EBU
SDI SG
SDI SG
AUDIO
CH23/4
-30
-40
-30
-40
-30
-40
-30
-40
-60
-60
-60
-60
PB FS
48k44.1k32k REC MODE
2CH4CH
3 1 1,2,3
1 Press the SEARCH button or search dial so that the
SHUTTLE indicator in the display section is lit.
Pressing the search dial toggles between jog mode and
shuttle mode.
2 Turn the search dial to the desired angle corresponding
to the desired playback speed.
Playback in shuttle mode starts.
3 To stop playback in shuttle mode, return the search
dial to the center position, or press the STOP button.
To return to normal-speed playback
Press the PLAY button.
To alternate between normal-speed playback and
shuttle mode playback
Set the search dial to the position corresponding to the
desired shuttle playback speed, then switch between
High-Speed and Low-Speed Search—Quickly and Accurately Determining Editing Points
Download from Www.Somanuals.com. All Manuals Search And Download.
54
SYSTEM MENU
SETUP MENU
AUTO FUNCTION
HOURS METER
Setup menu
Time counter display
Digitally Dubbing Signals
in DVCAM Format
In addition to straightforward tape dubbing, you can also
use this unit to dub automatically from the beginning of the
tape to the end through the i.LINK interface.
When you dub data recorded by a DVCAM camcorder that
supports the ClipLink function, you can also include the
data stored in the cassette memory.
Monitor screen
Notes
2 Press the J or j button to select “AUTO
FUNCTION.”
• Use a tape recorded in the DVCAM format. A tape
recorded in DV format cannot be used as a source tape
for dubbing through the i.LINK interface.
• Regardless of the audio recording mode setting of this
unit, dubbing is performed with the original audio
recording mode unchanged (two-channel/48 kHz mode
or four-channel/32 kHz mode).
SYSTEM MENU
Auto func
SETUP MENU
AUTO FUNCTION
HOURS METER
Time counter display
• Approximately the last 2 minutes of the tape may not be
copied because of differences in tape lengths. (If an
index picture is recorded in this portion, it may also not
be copied.)
• A continuous recorded section of approximately 5
seconds is required before the recording start point. It is
recommended to record beforehand color bars or a
similar signal at the start point of the source tape to be
dubbed on this unit.
Monitor screen
3 Press the k button.
Connections for dubbing via i.LINK interface
To carry out dubbing through the LINK interface,
connect the i.DV IN/OUT connectors on this unit and the
player.
This displays the items in the level 1 of the auto mode
execution menu.
AUTO FUNCTION MENU
i.LINK DUB
i.LINK DUBBING
Use the following procedure.
TC INSERT
Time counter display
A
B
MARK
Monitor screen
1,9
2,4
3,4,5 7
4 Press the k button to display the menu level 2 for the
item “i.LINK DUBBING,” and select the data to be
dubbed with the j button.
1 Press the MENU button on the menu control panel.
Digitally Dubbing Signals in DVCAM Format
Download from Www.Somanuals.com. All Manuals Search And Download.
55
i.LINK DUBBING
(A/V/TC/CM)
Example: Selecting “A/V/TC/CM”
AUTO FUNCTION MENU
Executing
Time counter display
>A/V/TC/CM
Time counter display
i.LINK DUBBING
A/V
EXECUTING.
A/V/TC
TCR 00:00:00:00
UBR 00:00:00:00
A/V/TC/CM
ABORT:MENU KEY
Monitor screen
Monitor screen
To end the dubbing operation while it is in progress
Press the STOP button.
5 Press the k button.
When the dubbing is completed, message
“COMPLETED” appears on the monitor screen and
“Completed” in the time counter display.
The source tape and recording tape are both
automatically rewound to the beginning, and the
cassettes ejected. When the cassette is ejected, this unit
returns to the state in step 5.
The following message appears.
i.LINK DUBBING
(A/V/TC/CM)
Set tape!
Time counter display
INSERT RECORD TAPE IN
THIS VTR AND SOURCE
TAPE IN THE PLAYER VTR.
8 To continue by dubbing another tape, repeat steps 6
and 7.
9 When the dubbing is completed, press the MENU
ABORT:MENU KEY
button to exit the menu.
Monitor screen
If the following message appears in step 6 for an
A/V/TC/CM dubbing operation
6 Insert the source tape in the player, and the recording
tape in this unit.
i.LINK DUBBING
CM capacity!
(A/V/TC/CM)
A message to confirm the dubbing operation appears.
Time counter display
CM MEMORY STORAGE
CAPACITY OF THE RECORD
TAPE IS TOO SMALL.
i.LINK DUBBING
Start dub?
(A/V/TC/CM)
Time counter display
START QSDI DUBBING?
ABORT:MENU KEY
Monitor screen
START:YES KEY
ABORT:MENU KEY
When carrying out A/V/TC/CM dubbing, if you insert the
cassettes in step 6, the cassette memory capacity of the
cassettes inserted in both this unit and the player are
checked automatically.
Monitor screen
If the cassette memory capacity of the source tape is larger
than that of the recording tape, the above message appears.
In this case, replace the recording tape by a tape with a
larger cassette memory capacity.
To cancel the dubbing operation
Press the MENU button.
7 Press the SET (YES) button.
The tape is automatically wound back to the
beginning, and dubbing starts.
Digitally Dubbing Signals in DVCAM Format
56
Download from Www.Somanuals.com. All Manuals Search And Download.
If the following message appears in step 7 for an
A/V/TC/CM dubbing operation
i.LINK DUBBING
Copy CM?
(A/V/TC/CM)
Time counter display
SDTI DUBBING IS ABORTED.
EXECUTE CM COPY?
COPY
:YES KEY
NOT COPY:NO KEY
Monitor screen
When carrying out A/V/TC/CM dubbing, if you press the
STOP button to stop dubbing in step 7, or if dubbing stops
because the source tape is longer than the recording tape,
the above message appears to confirm whether or not to
copy the contents of the cassette memory.
To copy the contents of the cassette memory, press the
SET (YES) button.
If you do not wish to copy the contents of the cassette
memory, press the RESET (NO) button. If you press the
RESET (NO) button, however, the contents of the cassette
memory may not agree with the material recorded on the
tape.
Digitally Dubbing Signals in DVCAM Format
Download from Www.Somanuals.com. All Manuals Search And Download.
57
Digitally Dubbing Signals in DVCAM Format
Download from Www.Somanuals.com. All Manuals Search And Download.
58
Menu Settings Chapter
4
Menu Organization
As shown in the following figure, the menu system
consists of four levels and is functionally divided into three
subsystems: the setup menu, the auto mode (AUTO
FUNCTION) execution menu and the digital hours meter
display menu. This chapter mainly describes the setup
menu, showing its contents and how to operate it.
For details of the AUTO FUNCTION menu, see “Digitally
For details of the digital hours meter display, see “Regular
The items of the setup menu are divided into several
functional groups on level 1, and except for the MENU
GRADE item the settings themselves are made on level 2
or level 3.
Also, the menu items are divided into two categories
according to how frequently they are accessed: the “basic”
items, to which frequent access is normally required, and
the “enhanced” items, which are less frequently used. In
the following figure, the items shown in boldface are basic
items, and the other items are enhanced items.
The menu settings are saved in non-volatile memory,
which means they are not erased when you power off the
unit after executing the setting operation.
Menu Organization
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu organization
Menu selection level
Level 1
Level 2
Level 3
REPEAT MODE
REPEAT TOP
REPEAT END
A PRESET
OPERATIONAL FUNCTION
REPEAT FUNCTION
SETUP MENU
B PRESET
CASSETTE OUT
F.FWD/REW
STOP
AUTO EE SELECT
LOCAL ENABLE
REC INHIBIT
STANDBY OFF
A1 EDIT CH
A2 EDIT CH
SEARCH ENABLE
MAX SRCH SPEED
SHUTTLE
F.FWD/REW
JOG RESPONSE
PREROLL TIME
AFTER CUE-UP
PLAY START
AUTO REW
A MODE CHANGE
CHARA. DISPLAY
CHARA. POSITION
CHARA. TYPE
CHARA. VSIZE
DISPLAY INFO
SUB STATUS
MENU DISPLAY
PEAK HOLD
DISPLAY CONTROL
OVER DISP HOLD
BRIGHTNESS
ALARM
TC MODE
TIME CODE
RUN MODE
a)
DF MODE
TC SELECT
VITC
TCG REGEN
UB BINARY GP.
VITC POS SEL-1
VITC POS SEL-2
VITC OUTPUT
EE OUT PHASE
MUTE IN SRCH
TAPE PROTECTION
FROM STOP
FROM STILL
STOP TIMER
STILL TIMER
NEXT MODE
(Continued)
a) Menu item for DSR-1800A only
Menu Organization
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu selection level
Level 1
(Continued)
VIDEO CONTROL
Level 2
Level 3
STILL MODE
EE DELAY
INT VIDEO SG
STD/NON-STD
OUT REF SEL
SETUP REMOVE
a)
a)
SETUP ADD
CC(F1) BLANK
a)
a)
CC(F2) BLANK
WIDE MODE
ESR MODE
PROCESS CONTROL
CONTROL DEV
C PHASE MODE
ADJ RANGE
VIDEO GAIN
CHROMA GAIN
CHROMA PHASE
a)
SETUP LEVEL
BLACK LEVEL
b)
b)
LINE 335
INPUT BLANK
AUDIO CONTROL
REC MODE
INPUT ARRANGE
REC LEVEL
REF LEVEL
LEVEL SELECT
INT AUDIO SG
OUTPUT CH3/4
OUTPUT PHASE
JOG CONTROL
SHUTTLE MUTE
AUDIO EDIT
CH1 IN LEVEL
CH2 IN LEVEL
CH3 IN LEVEL
CH4 IN LEVEL
OUTPUT LEVEL
DV PB ATT
DIGITAL PROCESS
SYSTEM EE MODE
SETUP BANK OPERATION
RECALL BANK1
RECALL BANK2
RECALL BANK3
RECALL BANK4
SAVE BANK 1
SAVE BANK 2
SAVE BANK 3
SAVE BANK 4
MENU GRADE
A/V
A/V/TC
A/V/TC/CM
AUTO FUNCTION
HOURS METER
i.LINK DUBBING
TC INSERT
T1:OPERATION
T2:DRUM ROTATION
T3:TAPE RUNNING
CT:THREADING
a) Menu item for DSR-1800A only
b) Menu item for DSR-1800AP only
Menu Organization
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Contents
Setup Menu
The purpose and settings of the setup menu items are
described below.
Examples:
Indication on monitor
screen
Indication in time counter
display
Indications of menu items and settings
OPERATIONAL FUNCTION [Operational]
In the table below entitled “Menu contents,” the indication
of each menu item or setting on the monitor screen is
shown first, then the indication of the same item or setting
in the time counter display of this unit is shown in square
brackets ([ ]).
CASSETTE OUT
[>> Cass. out]
[>>> EE]
*EE
• Settings preceded by an asterisk (such as *EE) are
factory default settings.
• In the time counter display, one to three “>” symbols
may precede item or setting indications depending on the
current menu level. Larger numbers of “>” symbols
indicate lower menu levels.
Menu contents
OPERATIONAL FUNCTION [Operational]: Operation
settings
Description of settings
REPEAT FUNCTION [>REP
FUNC]: Make settings for
repeat playback mode.
REPEAT MODE
[>>REPEAT MD]:
*OFF [>>> OFF]: Do not put the unit into repeat playback
mode.
Determine whether or ON [>>> ON]: Put the unit into repeat playback mode.
not to put the unit into ON (FREEZE) [>>> FREEZE]: Put the unit into freeze
repeat playback mode.
playback mode. In this case, while the unit is cueing up to
the repeat start point, the freeze picture of the repeat end
point is displayed.
REPEAT TOP [>>REP
TOP]: Determine
whether the repeat
start point is the
beginning of tape or
point A.
*TAPE TOP [>>>Tape top]: The repeat start point is the
beginning of tape.
A POINT [>>>A point]: The repeat start point is point A as set
by the user.
REPEAT END [>>REP
*VIDEO END [>>>VD end]: The repeat end point is the end
END]: Determine
of the video recorded portion.
whether the repeat end TAPE END [>>>Tape end]: The repeat end point is the end of
point is the end of the
tape.
video recorded portion, B POINT [>>>B point]: The repeat end point is point B as set
the end of tape or point
B.
by the user.
Specify a time code
value to be used as the
setting of point A.
Specify a time code
value to be used as the
setting of point B.
Menu Contents
62
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONAL FUNCTION [Operational]: Operation
settings
Description of settings
AUTO EE SELECT [> Auto EE]: CASSETTE OUT [>>
*EE [>>> EE]: Output video and audio signals received from
Determine whether the unit
enters EE mode or PB mode
when audio and video
signals from other equipment
are input.
When this unit is used as the
recorder for cut editing, it is
possible to output the input
audio and video signals to
the monitor. This enables
editing operation to be
carried out using a single
monitor.
Cass. out]: Operations
other equipment.
when the cassette has PB [>>> PB]: Mute video and audio signals.
been ejected
F. FWD/REW [>> F. FWD/ EE [>>> EE]: Output video and audio signals received from
REW]: Operations
other equipment.
when in fast forward or *PB [>>> PB]: The unit enters playback mode and outputs a
rewind mode
playback video signal. Audio signals are muted.
STOP [>> STOP]:
Operations when in
stop mode
EE [>>> EE]: Output video and audio signals received from
other equipment.
*PB [>>> PB]: The unit enters playback mode and outputs a
still picture.
STANDBY OFF [>> STBY EE [>>> EE]: Output video and audio signals received from
OFF]: Operations
when in standby off
mode
other equipment.
*PB [>>> PB]: The unit enters playback mode and outputs a
still picture.
LOCAL ENABLE [> Local ENA]: Select which of the tape
ALL DISABLE [>> All DIS]: All of the tape transport control
transport control buttons (EJECT, REW, PLAY, F FWD,
buttons are disabled.
STOP, and REC) operate when the REMOTE button is lit. *STOP & EJECT [>> STOP & EJ]: Only the STOP and
EJECT buttons are enabled.
ALL ENABLE [>> All ENA]: All of the tape transport control
buttons are enabled, and settings such as preroll time
change or time data display selection are effective.
REC INHIBIT [>REC INH]: Determine whether to prohibit
*OFF [>> OFF]: Do not prohibit recording on tape.
ON [>> ON]: Prohibit recording on tape. (The REC INHIBIT
indicator on the front panel lights.)
recording on tape.
A1 EDIT CH [> A1 Edit CH]: Determine which audio channel *CH-1 [>> CH-1]: Assign to channel 1.
the EDIT PRESET command set on an editing control unit CH-2 [>> CH-2]: Assign to channel 2.
(such as the PVE-500) for A1 is assigned to.
CH-3 [>> CH-3]: Assign to channel 3.
CH-1 & CH-2 [>> CH-1&2]: Assign to channel 1 and channel
2.
A2 EDIT CH [> A2 Edit CH]: Determine which audio channel *CH-2 [>> CH-2]: Assign to channel 2.
the EDIT PRESET command set on an editing control unit CH-3 [>> CH-3]: Assign to channel 3.
(such as the PVE-500) for A2 is assigned to.
CH-4 [>> CH-4]: Assign to channel 4.
CH-3 & CH-4 [>> CH-3&4]: Assign to channel 3 and channel
4.
SEARCH ENABLE [>Search ENA]: Select how the unit enters *DIAL DIRECT [>> DIAL]: Press the SEARCH button or,
the search mode.
except during recording or editing, turn the search dial.
VIA SEARCH KEY [>> via KEY]: Press the SEARCH button.
MAX SRCH SPEED [>Max
SRCH]: Specify the
SHUTTLE [>>SHUTTLE]: X60 [>>> X60]: Maximum 60 times normal speed
Specify the maximum *X32 [>>> X32]: Maximum 32 times normal speed
maximum tape speed in
search mode (shuttle) and
F.FWD (fast forward)/REW
(rewind) mode.
tape speed in search
mode (shuttle).
X16 [>>> X16]: Maximum 16 times normal speed
F.FWD/REW [>>F.FWD/
MAX [>>> MAX]: No maximum tape speed is specified.
REW]: Specify the
*X85 [>>> X85]: Maximum 85 times normal speed
maximum tape speed X60 [>>> X60]: Maximum 60 times normal speed
in F.FWD/REW mode. X32 [>>> X32]: Maximum 32 times normal speed
Note
When this item is set to MAX, the playback video signal is
muted.
Menu Contents
63
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONAL FUNCTION [Operational]: Operation
settings
Description of settings
JOG RESPONSE [>JOG dial]: Select the tape speed
*TYPE1 (-1 to +1) [>> type 1]: Tape speed varies linearly
over the range −1 to +1.
characteristics for the search dial rotation rate in jog mode.
TYPE2 (-3 to +3) [>> type 2]: Tape speed varies stepwise as
shown in the figure below over the range −3 to +3.
(Characterized by a zone around −1 and +1 where the
tape speed is independent of the rotation rate)
TYPE3 (-3 to +3) [>> type 3]: Tape speed varies linearly over
the range −3 to +3, as shown in the figure below.
TYPE3
TYPE2
Speed
FWD
Speed
FWD
+3
+3
Rotation rate
FWD
+1
Rotation rate
RVS
RVS
FWD
-1
-3
-3
RVS
RVS
PREROLL TIME [> Preroll]: Set the preroll time.
0 SEC [>> 0 sec] to 15 SEC [>> 15 sec]: The preroll time
can be set in one-second increments to between 0 and 15
seconds.
A preroll time of at least 5 seconds is recommended when
using this unit for editing. When an editing control unit such as
the PVE-500 has been connected, this setting is disabled and
the setting on the editing control unit is in effect. Operations
such as the preroll time setting and the time data switching
operation are also performed on the editing control unit.
Factory default setting: 5 SEC [>> 5 sec]
AFTER CUE-UP [> After CUE]: Select the operating mode
*STOP [>> STOP]: Stop mode
STILL [>> STILL]: Output still pictures in search mode.
following cue-up.
PLAY START [> PLAY start]: Set the timing for switching from 16 FRAME DELAY [>> 16 delay] to 4 FRAME DELAY
stop mode to playback mode.
[>> 4 delay]: The larger the numerical value, the
longer the delay. By adjusting this setting, it is
possible to reduce the phase synchronization time
and preroll time during editing.
In an editing system including an editing control unit such as
the PVE-500, you can adjust this setting so that the delay
before switching to playback mode is the same on all the decks
of the editing system. It is then no longer necessary to
synchronize the decks for editing, and the preroll time can be
shortened.
Factory default setting: 5 FRAME DELAY [>> 5 delay] (for
DSR-1800A) or 4 FRAME DELAY [>> 4 delay] (for DSR-
1800AP)
AUTO REW [>Auto REW]: Select whether to rewind the tape DISABLE [>> DISABLE]: Do not rewind the tape
automatically when recording or playback reaches the end
of a tape.
automatically.
*ENABLE [>> ENABLE]: Rewind the tape automatically.
A MODE CHANGE [>Aud change]: Determine whether or not *OFF [>> OFF]: Do not permit.
to permit an insert editing that uses a different audio
recording mode (2- or 4-channel mode) from that which
was used for the tape loaded in the recorder.
ON [>> ON]: Permit.
Menu Contents
64
Download from Www.Somanuals.com. All Manuals Search And Download.
DISPLAY CONTROL [Display]: Settings related to
indications on the monitor and the unit
Description of settings
CHARA. DISPLAY [> Chara disp]: Determine whether or not OFF [>> OFF]: Do not output text. (In spite of this setting,
to output text (such as time code values) from the VIDEO
OUT 2 (SUPER) connector.
pressing the MENU button causes menu text to be
output.)
*ON [>> ON]: Output text.
CHARA. POSITION [> Chara pos]: Set the position of text
Use JjK k buttons on the menu control panel to adjust the
superimposed on output from the VIDEO OUT 2 (SUPER) text position while watching the monitor screen.
connector to the monitor.
To return to the level 1 of the setup menu, press the MENU
button.
CHARA. TYPE [> Chara type]: Set the type of characters in
text superimposed on output from the VIDEO OUT 2
(SUPER) connector to the monitor.
Make the following settings while watching the monitor screen.
*WHITE (WITH BKGD) [>> White]: White characters on black
background
BLACK (WITH BKGD) [>> Black]: Black characters on white
background
WHITE/OUTLINE [>> W/outline]: White characters with black
outline
BLACK/OUTLINE [>> B/outline]: Black characters with white
outline
CHARA. VSIZE [>Chara size]: Determine the vertical size of Make the selection while watching the monitor screen.
characters such as time code output from the VIDEO OUT *×1 [>> ×1]: Standard size
2 (SUPER) connector for superimposed display on the
monitor.
×2 [>> ×2]: 2 times standard size
DISPLAY INFO [> DISP info]: Select information
superimposed on output from the VIDEO OUT 2 (SUPER)
connector to the monitor.
*TIME DATA & STATUS [>> Time&STA]: Time data and
operating mode indications
TIME DATA & UB [>> Time&UB]: Time data selected using
the COUNTER SEL button, and user bit data (When user
bit data is selected using the COUNTER SEL button, user
bit data and time code are shown.)
TIME DATA & CNT [>> Time&CNT]: Time data selected
using the COUNTER SEL button, and CNT value (When
CNT is selected using the COUNTER SEL button, CNT
value and time code are shown.)
TIME DATA & TIME[>> Time&Time]: Time data and VITC
TIME DATA ONLY [>> Time]: Time data only
REC DATE & TIME [>> REC Date]: The time data selected
with the COUNTER SEL button is shown in the time
counter display, and the date and time of recording are
shown on the monitor screen.
SUB STATUS [> Sub status]: Select supplementary status
*OFF [>> OFF]: Nothing of supplementary status information
information superimposed on output from the VIDEO OUT EDIT PRESET [>> Edit pre]: Indications of the editing mode
2 (SUPER) connector to the monitor.
settings made from the connected editing control unit
TC MODE [>> TC mode]: Indications of the operating mode
of internal time code generator
REMAIN [>> Remain]: Remaining capacity of the tape
AUDIO MIXING [>> Aud Mix]: Indications of input audio
mixing
ALL [>> ALL]: All of the above-mentioned items of
supplementary status information
For details of supplementary status information displayed on
the monitor when a setting other than OFF is selected, see
MENU DISPLAY [> Menu DISP]: Set the type of characters in Make the following settings while watching the monitor screen.
menu text superimposed on output from the VIDEO OUT 2 *WHITE (WITH BKGD) [>> White]: White characters on black
(SUPER) connector to the monitor.
background
BLACK (WITH BKGD) [>> Black]: Black characters on white
background
WHITE/OUTLINE [>> W/outline]: White characters with black
outline
BLACK/OUTLINE [>> B/outline]: Black characters with white
outline
Menu Contents
65
Download from Www.Somanuals.com. All Manuals Search And Download.
DISPLAY CONTROL [Display]: Settings related to
indications on the monitor and the unit
Description of settings
PEAK HOLD [>Peak hold]: Set the peak hold time for the
OFF [>> OFF] to 1.5 SEC [1.5 sec]: Set the peak hold time in
the range of OFF (no peak hold) to 1.5 seconds in 0.1
second steps.
audio level meters.
Factory default setting: OFF [>> OFF]
OVER DISP HOLD [> Hold OVER]: Determine whether or not *OFF [>> OFF]: Do not hold the OVER indication display.
to hold the OVER indication display on the audio level
meters once the indications light.
ON (HOLD) [>> ON]: Hold the OVER indication display.
Note
With ON selected, once the display is held it will remain held
unless you change the setting to OFF.
BRIGHTNESS [> Brightness]: Set the brightness of front
Set brightness as a percentage of the maximum.
100% [>> 100%]
panel indicators.
*75% [>> 75%]
50% [>> 50%]
ALARM [> ALARM]: Determine whether alarm messages are OFF [>> OFF]: Alarm messages are not issued.
issued or not. *ON [>> ON]: Alarm messages are issued.
TIME CODE [Time code]: Settings related to the time code Description of settings
generator
TC MODE [> TC mode]: Determine the time code to use:
*INT PRESET [>> PRESET]: Use internal time code with a
preset initial value.
internal time code using a preset initial value, regenerated
internal time code (locked to time code read from tape), or INT REGEN [>> REGEN]: Use internal time code locked to
external time code.
time code read from tape.
EXT REGEN [>> EXT]: Use external time code selected as
follows.
• When TC is selected
External time code input to the TIME CODE IN
connector
• When VITC is selected
The VITC time code present in the input video signal
Note
When the selected input mode is i.LINK (the i.LINK indicator is
lit in the Input selection/audio mode display section), setting
this item to EXT REGEN causes the internal time code
generator to automatically synchronize with the external time
code input to the unit via the i.LINK interface.
RUN MODE [> RUN mode]: Select the advancement (RUN)
*FREE RUN [>> FREE RUN]: Time code generator keeps
mode of the time code generator.
running.
REC RUN [>> REC RUN]: Time code generator only runs
while recording.
Note
Set to FREE RUN when carrying out editing with an editing
control unit. With the REC RUN setting, editing will not be
carried out correctly.
(For DSR-1800A only)
*ON (DF) [>> ON (DF)]: Drop frame mode
OFF (NDF) [>> OFF (NDF)]: Non-drop frame mode
DF MODE [> DF mode]: Select whether the time code
generator and time counter operate in drop frame mode or
non-drop frame mode.
Normally select drop frame mode, to keep in
synchronization with real time. The non-drop frame mode
is useful for example when using computer graphics, and
working on a frame count basis.
TC SELECT [>TC select]: Determine which to display in the
VITC [>> VITC]: Display VITC.
*TC [>> TC]: Display TC.
time counter display, TC or VITC.
Menu Contents
66
Download from Www.Somanuals.com. All Manuals Search And Download.
TIME CODE [Time code]: Settings related to the time code Description of settings
generator
VITC [> VITC]: Determine whether to record the internally
OFF [>> OFF]: Do not record the internally generated time
generated time code as VITC.
code as VITC. (VITC present in the input video signal is
recorded unchanged.)
*ON [>> ON]: Record the internally generated time code as
VITC.
TCG REGEN [>TCG regen]: Select the signal to be
*TC & UB [>> TC & UB]: Both the time code and user bits are
regenerated when the time code generator is in the
regenerated.
regeneration mode (i.e., when the TC MODE menu item is TC [>> TC]: Only the time code is regenerated.
set to INT REGEN or EXT REGEN).
UB [>> UB]: Only the user bits are regenerated.
UB BINARY GP. [> Binary Gp.]: Select the user bit binary
*000: NOT SPECIFIED [>> 000]: Character set not specified
001: ISO CHARACTER [>> 001]: 8-bit characters conforming
to ISO 646 and ISO 2022
group flag of the time code generator.
010: UNASSIGNED-1 [>> 010]: Undefined
011: UNASSIGNED-2 [>> 011]: Undefined
100: UNASSIGNED-3 [>> 100]: Undefined
101: PAGE/LINE [>> 101]: Multiplex
110: UNASSIGNED-4 [>> 110]: Undefined
111: UNASSIGNED-5 [>> 111]: Undefined
Note
When the TC MODE menu item is set to EXT REGEN, the
user-bit binary group flag setting follows the setting on the time
code input to this unit.
VITC POS SEL-1 [>VITC pos-1]: Select a line to insert the
(For DSR-1800A)
12 LINE [>> 12 line] to 20 LINE [>> 20 line]: Select any line
from 12 to 20.
VITC in.
Factory default setting: 16 LINE [>> 16 line]
Note
You can insert the VITC signal in two places. To insert it in two
places, set both this item and also VITC POS SEL-2.
(For DSR-1800AP)
Select a line to insert the VITC in.
9 LINE [>> 9 line] to 22 LINE [>> 22 line]: Select any line
from 9 to 22.
Factory default setting: 19 LINE [>> 19 line]
VITC POS SEL-2 [>VITC pos-2]: Select a line to insert the
(For DSR-1800A)
VITC in.
12 LINE [>> 12 line] to 20 LINE [>> 20 line]: Select any line
from 12 to 20.
Factory default setting: 18 LINE [>> 18 line]
Note
You can insert the VITC signal in two places. To insert it in two
places, set both this item and also VITC POS SEL-1.
(For DSR-1800AP)
Select a line to insert the VITC in.
9 LINE [>> 9 line] to 22 LINE [>> 22 line]: Select any line
from 9 to 22.
Factory default setting: 21 LINE [>> 21 line]
VITC OUTPUT [>VITC out]: Select the time code to be output OFF [>> OFF]: Do not output VITC.
as VITC.
TC [>> TC]: Output TC after converting it into VITC.
*VITC [>> VITC]: Output VITC.
EE OUT PHASE [>EE out]: Determine the output phase for
the LTC signal output from the TIME CODE OUT
connector when recording time code and in STOP REC
mode (forced EE mode).
*MUTE [>>mute]: Mute the output.
THROUGH [>> through]: Output the time code input to the
TIME CODE IN connector as it is. (See example
VIDEO INPUT PHASE [>> V input]: Output the time code
with the same phase as the input video signal phase.
VIDEO OUTPUT PHASE [>> V output]: Output the time code
with the same phase as the output video signal phase.
MUTE IN SRCH [>Mute in SR]: Select whether to mute the
output from the TIME CODE OUT connector in search
(jog/shuttle) mode.
OFF [>> OFF]: Do not mute.
*ON [>> ON]: Mute.
Menu Contents
67
Download from Www.Somanuals.com. All Manuals Search And Download.
TAPE PROTECTION [Tape protct]: Settings related to tape Description of settings
and video head protection
FROM STOP [> From STOP]:
Set the time to switch from
stop mode to tape protection
mode.
STOP TIMER [>> STP
timer]: Set the time to
switch from stop mode
to tape protection
mode.
5 MIN [>>> 5 min] to 0.5 SEC [>>> 0.5 sec]: Select time from
12 settings ranging from 0.5 second to 5 minutes in steps
of 0.1 second.
Factory default setting: 1MIN [>>> 1min]
Note
If the value is set to 1 minute or more, the unit enters internal
protection mode in 1 minute, which makes start up slower.
FROM STILL [> From STILL]:
Set the time to switch from
still search mode to tape
protection mode. Also select
the type of tape protection
mode.
STILL TIMER [>> STL
timer]: Set the time to
switch from still search
mode to tape
5 MIN [>>> 5 min] to 0.5 SEC [>>> 0.5 sec]: Select time from
12 settings ranging from 0.5 second to 5 minutes in steps
of 0.1 second.
Factory default setting: 1MIN [>>> 1min]
protection mode.
Note
If the value is set to 1 minute or more, the unit enters internal
protection mode in 1 minute, which makes start up slower.
1
NEXT MODE [>> Next
mode]: Select the type
of tape protection
mode to follow still
search mode when the
time set with the STILL
TIMER menu item
elapses.
*STEP FWD [>>> Step]: The tape is advanced at / times
30
normal speed for about 2 seconds.
STANDBY OFF [>>> STANDBY]: Standby off mode
Note
The Step setting is enabled only when “STILL TIMER” is set to
less than 1 minute.
VIDEO CONTROL [Video]: Settings related to video control Description of settings
STILL MODE [> STILL mod]: Select the image to output in
*AUTO [>> Auto]: Output field 1 or field 2 as the still image,
still image mode.
according to the position the tape is stopped.
FRAME [>> Frame]: Output a full frame as the still image.
FIELD1 [>> Field 1]: Output only field 1 as the still image.
FIELD2 [>> Field 2]: Output only field 2 as the still image.
EE DELAY [>EE delay]: An E-E video signal is output delayed *SYNC DELAY [>> sync]: Delay the sync signal by the
with respect to the video input signal by the time for video corresponding amount of time before attaching it.
circuit processing. With this item, select whether or not to VIDEO DELAY [>> video]: Attach a sync signal with the same
delay the sync signal attached to the output video signal by
an amount corresponding to the video signal delay.
timing as the input signal.
INT VIDEO SG [>Video SG]: Select the test signal to be
*75% COLOR BARS [>>75% bars]: 75% color bar signal
output from the internal test signal generator. When SG is BLACK BURST [>>BB]: Black burst signal
selected using the VIDEO IN button, the internal test signal
generator outputs the selected test signal. This signal can
be recorded.
STD/NON-STD [>STD/N-STD]: Select the STD or NON-STD *FORCED STD [>> STD]: The STD mode is always used
mode in accordance with the composite video or S-video
input.
(forced STD mode).
FORCED NON-STD [>> NON-STD]: Use this setting when
the input video signal is unstable (forced NON-STD
mode).
OUT REF SEL [>Out Ref.]: Select the reference video signal *REF VIDEO [>> REF]: Use the signal input to a REF. VIDEO
to use.
IN connector as the reference video signal. The input
video signal to be edited is required to be in
synchronization with the reference video signal.
INPUT VIDEO [>> INPUT]: Use the input video signal
selected with the VIDEO IN button in the INPUT SELECT
section.
(For DSR-1800A only)
*OFF [>> OFF]: Do not remove black setup.
SETUP REMOVE [> Setup rmv]: Determine whether or not to ON (REMOVE) [>> ON]: Remove black setup.
remove black setup (7.5 IRE) from input analog video
signals when converting them into digital signals.
(For DSR-1800A only)
*OFF [>> OFF]: Do not add black setup.
SETUP ADD [> Setup add]: Determine whether or not to add ON (ADD) [>> ON]: Add black setup.
black setup to analog video output signals.
Menu Contents
68
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO CONTROL [Video]: Settings related to video control Description of settings
(For DSR-1800A only)
*OFF [>> OFF]: Do not mute.
ON [>> ON]: Mute.
CC(F1) BLANK [>CC1 blank]: Select whether to mute the
closed caption signal to be superimposed on the 1st field
of the output video signal.
(For DSR-1800A only)
*OFF [>> OFF]: Do not mute.
ON [>> ON]: Mute.
CC(F2) BLANK [>CC2 blank]: Select whether to mute the
closed caption signal to be superimposed on the 2nd field
of the output video signal.
WIDE MODE [>Wide mode]: Determine whether to retain
wide-screen aspect ratio information accompanying video
being recorded or played back.
*AUTO [>> Auto]: When video being recorded or played back
is accompanied by wide-screen aspect ratio information,
retain the information.
OFF [>> OFF]: Ignore wide-screen aspect ratio information.
ON [>> ON]: Whenever recording or playing back video, retain
wide-screen aspect ratio information.
ESR MODE [>ESR mode]: Select whether to enable the edge *OFF [>> OFF]: Do not enable.
subcarrier reducer (ESR).
ON [>> ON]: Enable.
When playing back a composite signal, set this to ON.
PROCESS CONTROL [>Proc
ctrl]
CONTROL DEV [>>Ctrl
dev]: Select the
*REMOTE [>>>REMOTE]: Use an optional remote control
unit to control the internal digital video processor.
MENU [>>> MENU]: Use the setup menu to change the
settings for the internal digital video processor.
method of controlling
the internal digital
video processor.
C PHASE MODE [>>C
Phas MD]: Select the
phase rotation mode
for chroma phase
*U/V (COMPOSITE) [>>> Cmpst]: Select this setting when
observing the composite video output level using a
composite vectorscope.
PB/PR (COMPONENT) [>>> Cmpnt]: Select this setting
when observing the component video output level using a
component vectorscope.
control.
The effect of this setting
applies to the output levels
of all of the composite
video, S video, SDI and
component video signals.
ADJ RANGE [>>Adj
range]: Select the
variable range of the
VIDEO and CHROMA
gains.
*−3 to +3 (dB) [>>> −3/+3]: −3 dB to +3 dB
WIDE [>>> wide]: −∞ to +3 dB
VIDEO GAIN [>>V gain]:
00H to 3FFH
Adjust the video output Factory default setting: 200H
level.
CHROMA GAIN [>>C
gain]: Adjust the
00H to 3FFH
Factory default setting: 200H
chroma output level.
CHROMA PHASE [>>C
phase]: Adjust the
chroma phase.
00H to FFH
Factory default setting: 80H
(For DSR-1800A only)
SETUP LEVEL [>>Setup
lev]: Adjust the black
setup level.
00H to 3FFH
Factory default setting: 200H
(For DSR-1800AP only)
BLACK LEVEL [>>Black
lev]: Adjust the black
level.
00H to 3FFH
Factory default setting: 200H
(For DSR-1800AP only)
INPUT BLANK [>Input blnk]
LINE 335 [>>Line 335]:
Switch blanking on or
off for the 335th line of
the input video signal.
BLANK [>>> blank]: Blank.
THROUGH [>>> through]: Do not blank.
Menu Contents
69
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO CONTROL [Audio]: Settings related to audio
control
Description of settings
REC MODE [>REC mode]: Select the audio recording mode. *2CHANNEL (48kHz) [>> 2 ch]: 2-channel, 48-kHz mode
4CHANNEL (32kHz) [>> 4 ch]: 4-channel, 32-kHz mode
INPUT ARRANGE [>Input arng]: Make settings for input
Set the channels on which to record the input audio signals as
follows.
audio mixing.
(1) Use the KkJj buttons to move the cursor and the SET
(YES) button to toggle the setting on and off.
(2) To save the settings, press the MENU button to return to
the previous screen, then press the SET (YES) button.
Example settings:
AUDIO INPUT SOURCE
ARRANGE
1
in1 in2 in3 in4
2
ch1:*on
ch2:
ch3:
ch4
on
on
on
on
3
4
ON/OFF : SET KEY
TO MENU : MENU KEY
1 Input audio channel 1 (“in1”) is recorded on audio channel 1
(“ch1”) on tape.
2 Input audio channels 2 and 4 (“in2” and “in4”) are recorded
mixed on audio channel 2 (“ch2”) on tape.
3 Input audio channel 4 (“in4”) is recorded on audio channel 3
(“ch3”) on tape.
4 Input audio channel 3 (“in3”) is recorded on audio channel 4
(“ch4”) on tape.
REC LEVEL [>Rec level]: Determine whether to enable or
disable the AUDIO INPUT LEVEL control knobs on the
front panel.
*VARIABLE [>> Variable]: Enable.
PRESET [>> Preset]: Disable.
Menu Contents
70
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO CONTROL [Audio]: Settings related to audio
control
Description of settings
LEVEL SELECT [>Level Sel]
REF LEVEL [>>REF
Level]: Select the
audio reference level
(headroom) for
*−20 dB [>>> −20dB] (factory default setting for DSR-1800A)
*−18 dB [>>> −18dB] (factory default setting for DSR-
1800AP)
−16 dB [>>> −16dB]
−12 dB [>>> −12dB]
recording on tape.
CH1 IN LEVEL [>>CH1
input]: Select the
*+4 dBm [>>> +4dBm]
0 dBm [>>> 0dBm]
audio level setting
−3 dBm [>>> −3dBm] (for DSR-1800AP only)
according to the audio −6 dBm [>>> −6dBm]
level of the signal input
to the AUDIO IN CH-1
connector.
CH2 IN LEVEL [>>CH2
input]: Select the
*+4 dBm [>>> +4dBm]
0 dBm [>>> 0dBm]
audio level setting
−3 dBm [>>> −3dBm] (for DSR-1800AP only)
according to the audio −6 dBm [>>> −6dBm]
level of the signal input
to the AUDIO IN CH-2
connector.
CH3 IN LEVEL [>>CH3
input]: Select the
*+4 dBm [>>> +4dBm]
0 dBm [>>> 0dBm]
audio level setting
−3 dBm [>>> −3dBm] (for DSR-1800AP only)
according to the audio −6 dBm [>>> −6dBm]
level of the signal input
to the AUDIO IN CH-3
connector.
CH4 IN LEVEL [>>CH4
input]: Select the
*+4 dBm [>>> +4dBm]
0 dBm [>>> 0dBm]
audio level setting
−3 dBm [>>> −3dBm] (for DSR-1800AP only)
according to the audio −6 dBm [>>> −6dBm]
level of the signal input
to the AUDIO IN CH-4
connector.
OUTPUT LEVEL [>>Out
Level]: Select the
analog audio output
reference level.
*+4 dBm [>>> +4dBm]
0 dBm [>>> 0dBm]
−3 dBm [>>> −3dBm] (for DSR-1800AP only)
−6 dBm [>>> −6dBm]
INT AUDIO SG [>Audio SG]: Select the operation of the
SILENCE [>> silence]: Silent signal
internal audio test signal generator.
*1kHz SINE [>> 1kHz]: 1-kHz, −20 dB FS sine wave signal
When you select SG as the audio input in the INPUT SELECT
section on the front panel, the audio test signal generated by
the internal audio test signal generator is input.
OUTPUT CH3/4 [>OUT ch3/4]: Select the signals to be output *LINE OUT [>> line out]: Output the audio channel-3 and
from the AUDIO OUT CH-3 and AUDIO OUT CH-4
connectors.
audio channel-4 signals from the AUDIO OUT CH-3 and
AUDIO OUT CH-4 connectors as they are.
MONITOR OUT [>> monitor]: Output the monitor audio L-
channel (CH-1) and monitor audio R-channel (CH-2)
signals from the AUDIO OUT CH-3 and AUDIO OUT CH-
4 connectors, respectively.
OUTPUT PHASE [>Out phase]: Select the audio playback
AUDIO OUTPUT PHASE: 0 to FF (Select in this range.)
The reference position corresponds to a setting of 80H. When
a value smaller than 80H is selected, the output timing is
advanced, and when a value larger than 80H is selected, the
output timing is delayed. (80H = 128 samples = approx. 2.7
ms, 1 sample = approx. 20 µs)
signal output timing.
Factory default setting: 80H
JOG CONTROL [> Jog ctrl]: Select whether to adjust the
OFF [>> OFF]: Do not adjust the audio playback speed.
*ON [>> ON]: Adjust the audio playback speed.
audio playback speed during slow playback.
Menu Contents
71
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO CONTROL [Audio]: Settings related to audio
control
Description of settings
SHUTTLE MUTE [>Shutl mute]: Set the audio muting
*OFF [>> OFF]: Not muted.
CUEUP or PREROLL [>> CUEUP]: Muted during cue-up or
preroll operations.
conditions during shuttle playback.
FULL [>> FULL]: Muted in shuttle mode.
AUDIO EDIT [>Audio edit]: Specify the type of editing for
CUT EDIT [>> Cut edit]: Cut editing (Discontinuity in audio
signal may result at the editing point, causing noise during
playback.)
audio signals.
*CROSS FADE [>> Cross]: Cross-fade
IN/OUT
FADE IN/OUT [>> Fade]: Fade in and fade out
IN
OUT
DV PB ATT [>DV PB ATT]: When playing back a tape
recorded in consumer DV format, select whether to
attenuate the audio output level.
OFF [>> OFF]: Do not attenuate.
*ON [>> ON]: Attenuate.
DIGITAL PROCESS [Digi. proc]: Settings related to digital Description of settings
process
SYSTEM EE MODE [>System EE]: Select the bypass E-E
*OFF [>> OFF]: Bypass E-E (ordinary setting)
ON [>> ON]: System E-E
mode or system E-E mode.
SETUP BANK OPERATION [Setup Bank]: Settings related Description of settings
to menu bank operations
RECALL BANK1 [>Recall 1]: Recall menu settings from
(1) Select the bank you want to recall, then press the k
menu bank 1.
button.
Message “RECALL OK?” appears.
(2) To recall, press the SET (YES) button.
To quit recalling, press the RESET (NO) button.
RECALL BANK2 [>Recall 2]: Recall menu settings from
menu bank 2.
RECALL BANK3 [>Recall 3]: Recall menu settings from
menu bank 3.
RECALL BANK4 [>Recall 4]: Recall menu settings from
menu bank 4.
SAVE BANK 1 [>Save 1]: Save current menu settings to menu (1) Select the bank you want to save, then press the k
bank 1.
button.
Message “SAVE OK?” appears.
(2) To save, press the SET (YES) button.
To quit saving, press the RESET (NO) button.
SAVE BANK 2 [>Save 2]: Save current menu settings to menu
bank 2.
SAVE BANK 3 [>Save 3]: Save current menu settings to menu
bank 3.
SAVE BANK 4 [>Save 4]: Save current menu settings to menu
bank 4.
Menu banks
This unit allows four different complete sets of menu settings to be saved in what are termed “menu banks” numbered 1 to 4.
Saved sets of menu settings can be recalled for use as required.
Menu Contents
72
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU GRADE [Menu grade]: Selection of menu items to
be displayed
Description of settings
Determine whether to display basic items only or both basic
and enhanced items on the monitor screen and in the time
counter display when using the menu.
*BASIC [> Basic]: Display basic items only.
ENHANCED [> Enhanced]: Display both basic and enhanced
items.
• VIDEO INPUT PHASE mode
The time code output signal is synchronized with the
input video signal.
This mode is appropriate when the output from a single
device is recorded on a number of VCRs. The
connections are loop-through connections.
In this mode, the same time code is recorded on all of the
VCRs 1 to n.
EE OUT PHASE settings for time code
output
Use the following as reference information when setting
• THROUGH mode
In this mode, the LTC signal is output with the phase
synchronized with the input time code signal. This mode
is appropriate when recording signals from multiple
devices on a number of VCRs.
VIDEO OUT
VIDEO IN
When the camcorder is in genlock mode, the time code
precision is 0 frames. When the camcorder is not in
genlock mode, it is 1 frame.
VIDEO LOOP THRU
TIME CODE IN
TIME CODE OUT
DSR-1800A/1800AP
(1st unit)
Output device
(VCR, camera, etc.)
VIDEO IN
AUDIO IN
VIDEO IN
TIME CODE IN
VIDEO LOOP THRU
TIME CODE IN
TIME CODE OUT
Camcorder 1
TIME CODE OUT
DSR-1800A/1800AP
(1st unit)
DSR-1800A/1800AP
(2nd unit)
VIDEO IN
AUDIO IN
TIME CODE IN
TIME CODE OUT
Camcorder 2
DSR-1800A/1800AP
(2nd unit)
VIDEO IN
VIDEO LOOP THRU
TIME CODE IN
TIME CODE OUT
DSR-1800A/1800AP
(nth unit)
VIDEO IN
AUDIO IN
Composite video or SDI (video and audio) signal
Time code signal
TIME CODE IN
TIME CODE OUT
Camcorder n
DSR-1800A/1800AP
(nth unit)
Composite video or S-video signal
Audio signal
Time code signal
Menu Contents
73
Download from Www.Somanuals.com. All Manuals Search And Download.
• VIDEO OUTPUT PHASE mode
The time code output signal is synchronized with the
output video signal.
This mode is appropriate when outputting signals from a
single device to a number of VCRs using separate cables
for video, audio, and time code.
In this mode, the same time code is recorded on all of the
VCRs 1 to n.
VIDEO OUT
AUDIO OUT
VIDEO IN
VIDEO OUT
AUDIO IN
TIME CODE OUT
AUDIO OUT
TIME CODE IN
TIME CODE OUT
Output device
(VCR, camera, etc.)
DSR-1800A/1800AP
(1st unit)
VIDEO IN
VIDEO OUT
AUDIO IN
AUDIO OUT
TIME CODE IN
TIME CODE OUT
DSR-1800A/1800AP
(2nd unit)
VIDEO IN
VIDEO OUT
AUDIO IN
AUDIO OUT
TIME CODE IN
TIME CODE OUT
DSR-1800A/1800AP
(nth unit)
• Composite video signal
• S-video signal
• Analog component signal
• SDI (video and audio) signal
Audio signal
Time code signal
Menu Contents
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto Mode (AUTO FUNCTION) Execution Menu
The following table shows the purpose and function of the
items in the auto mode execution menu.
For details of the use of individual items, see “Digitally
Menu contents
i.LINK DUBBING [i.LINK DUB]: Selection of data for i.LINK Settings
dubbing
For dubbing through the i.LINK interface, select data that the
dubbing applies to.
A/V [> A/V]: Dub the audio and video.
A/V/TC [> A/V/TC]: Dub the audio, video, and time code.
A/V/TC/CM [> A/V/TC/CM]: Dub the audio, video, time code,
and cassette memory contents.
Note
When A/V is selected, the time code recorded follows the
setup menu.
TC INSERT [TC insert]: Time code rewriting
Settings
Rewrite the time code from an initial value which can be set
freely.
−
Menu Contents
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Settings of Basic
Items
Changing Menu Settings
The factory default setting is to display only the basic
items. To change the settings of basic items proceed as
follows.
This section explains how to change menu settings.
Buttons Used to Change Settings
Use the following buttons on the menu control panel to
change the menu settings.
1
3,5,7
Menu control buttons
Functions
MENU button
• Opens the menu and
launches menu control
mode.
2,4,6
• Closes the menu and exits
menu control mode.
A
B
J and j buttons
These buttons move the
highlighted cursor up and
down within the current level
to select an item or setting.
Hold down one of these
buttons to make the
MARK
9
8
highlighted cursor move
continuously.
1 Press the MENU button on the menu control panel.
K and k buttons
• Press the k button to go
down one level.
• Press the K button to go
up one level.
The menu selection level display appears on the
monitor. In the figure below, “SETUP MENU” is
selected (shown in reverse video).
Hold down one of these
buttons to make the
highlighted cursor move
continuously.
The time counter display of this unit shows only the
currently selected item. When the item name is long, it
is abbreviated.
RESET (NO) button
SET (YES) button
• Returns the setting to the
factory default setting.
• Sends a negative
response to prompts on
the monitor screen.
Menu selection level display
SYSTEM MENU
Setup menu
SETUP MENU
AUTO FUNCTION
Time counter display
HOURS METER
• Saves the new setting in
memory.
• Sends a positive response
to prompts on the monitor
screen.
Monitor screen
Changing Menu Settings
76
Download from Www.Somanuals.com. All Manuals Search And Download.
2 With “SETUP MENU” selected, press the k button.
This displays all items on menu level 1.
Level-1 menu display
5 Press the J or j button to select the item whose
setting you wish to change.
For menu items on level 3, press the k button to go
to the level 3, then press the J or j button to select the
item whose setting you wish to change.
SETUP MENU
Operational
OPERATIONAL FUNCTION
DISPLAY CONTROL
Example: Display when “BRIGHTNESS” is selected
Time counter display
TIME CODE
SETUP BANK OPERATION
SETUP MENU
> Brightness
DISPLAY CONTROL
MENU GRADE
:BASIC
CHARA.DISPLAY :ON
Time counter display
CHARA.POSITION
CHARA.TYPE
CHARA.VSIZE
DISPLAY INFO
SUB STATUS
MENU DISPLAY
PEAK HOLD
:WHITE
:x1
:T&STA
:OFF
:WHITE
:OFF
Monitor screen
OVER DISP HOLD :OFF
BRIGHTNESS :75%
ALARM :ON
3 Press the J or j button to select the required item.
Monitor screen
Example: Display when “DISPLAY CONTROL” is selected
6 Press the k button.
SETUP MENU
Display
OPERATIONAL FUNCTION
This displays all possible settings for the item selected
in step 5.
DISPLAY CONTROL
Time counter display
TIME CODE
SETUP BANK OPERATION
SETUP MENU
>> 75%
MENU GRADE
:BASIC
DISPLAY CONTROL
BRIGHTNESS
100%
:75%
Time counter display
* 75%
50%
Monitor screen
4 Press the k button.
This displays the menu level 2 for the menu item
Monitor screen
selected in step 3.
Example: Level-2 display for “DISPLAY CONTROL”
7 Press the J or j button to change the setting of the
item.
SETUP MENU
> Chara disp
DISPLAY CONTROL
CHARA.DISPLAY :ON
Time counter display
SETUP MENU
>> 50%
CHARA.POSITION
DISPLAY CONTROL
CHARA.TYPE
CHARA.VSIZE
DISPLAY INFO
SUB STATUS
MENU DISPLAY
PEAK HOLD
:WHITE
:x1
BRIGHTNESS
100%
:75%
Time counter display
:T&STA
:OFF
* 75%
50%
Current settings
:WHITE
:OFF
OVER DISP HOLD :OFF
BRIGHTNESS :75%
ALARM :ON
Monitor screen
Monitor screen
8 To change other settings, press the K button to return
to the previous screen, then repeat steps 5 to 7 as
required.
Changing Menu Settings
77
Download from Www.Somanuals.com. All Manuals Search And Download.
9 When you have completed the settings, press the SET
Displaying Enhanced Items
(YES) button.
The factory default setting is not to display enhanced
items.
The message “NOW SAVING...” appears on the
monitor screen, and “Saving...” appears in the time
counter display, while the new settings are saved in
memory.
When the saving operation is completed, the monitor
screen and time counter display return to their normal
indications.
To display enhanced items, set the MENU GRADE menu
procedure in the previous section “Changing the Settings
of Basic Items.” (In step 3, first select “MENU GRADE,”
and next select “ENHANCED,” then press the SET (YES)
button to save the setting in memory.)
Notes
With this done, when you press the MENU button and the
k button to display the setup menu, all basic and
enhanced items in the menu level 1 appear.
• If you power off the unit before saving operation is
completed, settings may be lost. Wait until the
saving is completed before powering off the unit.
• If, instead of pressing the SET (YES) button, you
press the MENU button, the new settings are not
saved. The message “ABORT!” appears on the
monitor screen and “Abort!” in the time counter
display for about 0.5 second, and the system exits
the menus. To change more than one setting, be sure
to press the SET (YES) button after making the
settings.
Changing the Settings of Enhanced
Items
To change the settings of enhanced items, first carry out
the procedure in the previous section “Displaying
Enhanced Items,” then proceed as follows.
2
1
Meanings of indications on the monitor
screen
On-screen indication
Meaning
A
B
Right-pointing arrow (k) at
the right of a menu item
See step 1 of the foregoing
operating procedure.
Pressing the k button
switches to the next lower
menu level or to a setting
selection screen.
MARK
Left-pointing arrow (K) at
the left of a menu item
See step 4 of the foregoing
operating procedure.
Pressing the K button
returns to the previous
(higher) menu level.
3
4
1 Press the MENU button on the menu control panel.
Character string at the right of Current setting of the menu
a menu item
See step 4 of the foregoing
operating procedure.
item.
The menu selection level display appears on the
monitor.
• When shown with a colon
(:): the current setting is
the same as the factory
default setting.
• When shown with a raised
dot (•): the current setting
is different from the factory
default setting.
See step 2 of the operating
procedure in “Changing the
2 With “SETUP MENU” selected, press the k button.
This displays all basic and enhanced items on menu
level 1.
Level-1 menu display
SETUP MENU
Menu grade
OPERATIONAL FUNCTION
DISPLAY CONTROL
Time counter display
TIME CODE
An asterisk in a complete list Factory default setting.
of settings
See step 6 of the foregoing
operating procedure.
TAPE PROTECTION
VIDEO CONTROL
AUDIO CONTROL
DIGITAL PROCESS
SETUP BANK OPERATION
ENHAN
MENU GRADE
Current setting
Monitor screen
Changing Menu Settings
78
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Follow the same procedure as in steps 3 to 8 of the
procedure in the section “Changing the Settings of
Basic Items” on page 76 using the arrow buttons to
select an item and change its setting.
4 Press the SET (YES) button.
The message “NOW SAVING...” appears on the
monitor screen, and “Saving...” appears in the time
counter display, while the settings of all items are
returned to their factory default settings. These factory
default settings are saved in memory.
4 When you have completed the settings, press the SET
(YES) button.
Note
The message “NOW SAVING...” appears on the
monitor screen, and “Saving...” appears in the time
counter display, while the new settings are saved in
memory.
When the saving operation is completed, the monitor
screen and time counter display return to their normal
indications.
If you power off the unit while settings are being
saved, settings may not be correctly returned to their
factory default settings. Wait until the saving is
completed before powering off the unit.
To abandon the resetting operation
Instead of pressing the SET (YES) button, press the
RESET (NO) button. The display returns to menu
level 1, leaving the settings unchanged.
Returning Menu Settings to Their
Factory Default Settings
After making menu setting changes, to return settings to
their factory default settings (setting initialization), use the
following procedure.
To return a particular setting to its factory
default setting
In the display for changing the target setting, press the
RESET (NO) button.
Carry out the procedure in the section “Changing the
the current setting displayed (in the example, if the setting
has been changed it will be “100%” or “50%”), press the
RESET (NO) button. The setting returns to its factory
default setting of “75%.”
To return all settings to their factory
default settings
Use the following procedure.
1 Press the MENU button on the menu control panel to
display the menu selection.
2 Press the k button to display level 1 of the setup
menu.
3 Press the RESET (NO) button.
A message appears, to confirm whether or not you
wish to return all settings to their factory default
settings.
Monitorscreen
message
“INITIALIZE ALL ITEMS TO
FACTORY PRESET VALUES?”
Message in the time “Init setup?”
counter display
Changing Menu Settings
79
Download from Www.Somanuals.com. All Manuals Search And Download.
When the SUB STATUS menu item is set to TC MODE:
Displaying
Supplementary Status
Information
On-screen
indication
Meaning
INT PRESET FREE
[IP F]
The internal time code generator is
operating in FREE RUN mode.
INT PRESET REC
[IP R]
The internal time code generator is
operating in REC RUN mode.
When you set the SUB STATUS menu item (see page 65)
to other than OFF, you can view supplementary status
information on the monitor screen below the operating
mode display area.
INT REGEN-T&U
[IRTU]
The internal time code generator is
in synchronization with the playback
time code (LTC) read from tape.
EXT LTC-T&U
[ELTU]
The internal time code generator is
in synchronization with the external
time code (LTC) input to the unit
and is generating the same time
code value and user bit value as
those of the external time code
(regeneration).
.
.
T C R
0 0
P L A Y
I N S
:
0 4
A 1
4 7
L O C K
3 4 T C
0 7
2
V
EXT VITC-T&U
[EVTU]
The internal time code generator is
in synchronization with VITC
present in the external video signal
input to the unit and is generating
the same time code value and user
bit value as those of the external
time code (regeneration).
Supplementary status information
The following items of supplementary status information
are displayed depending on the setting of the SUB
STATUS menu item.
EXT DVIN-T&U
[EDTU]
The internal time code generator is
in synchronization with the external
time code input to the unit via i.LINK
(DV IN) interface and is generating
the same time code value and user
bit value as those of the external
time code (regeneration).
Setting of SUB
Items of supplementary
information displayed
STATUS menu item
EDIT PRESET
TC MODE
Editing mode settings made on the
editing control unit
Operating mode of the internal time
code generator
EXT DVIN.V-T&U
[EDTU]
The internal time code generator is
in synchronization with the external
VITC input to the unit via i.LINK (DV
IN) interface and is generating the
same time code value and user bit
value as those of the external time
code (regeneration).
REMAIN
AUDIO MIXING
ALL
Remaining capacity of the tape
Setting for input audio mixing
All of the above items
The following tables show the on-screen indications of
supplementary information and their meaning.
In each table, the indications given in brackets such as
[ASM] are the indications displayed when the SUB
STATUS menu item is set to ALL.
When the SUB STATUS menu item is set to REMAIN:
On-screen
indication
Meaning
REMAIN 184 min
Remaining capacity of the tape in
minutes.
For the display format when ALL is selected, see page 81.
When the remaining capacity has
not been detected, “REMAIN ---
min” appears.
When the SUB STATUS menu item is set to EDIT
PRESET:
When the SUB STATUS menu item is set to AUDIO
MIXING:
On-screen indication
Meaning
On-screen indication
Meaning
ASM [ASM]
Assemble editing mode
1234
[MIX]
Input audio channels
selected for mixing
1234: Input audio channels
1, 2, 3 and 4
INS V A1234 TC
[V1234T]
INS: Insert editing mode
V A1234 TC: Channels or
signals selected for
insert editing
V: Video
A1234: Audio 1, 2, 3, 4
TC: Time code
Displaying Supplementary Status Information
Download from Www.Somanuals.com. All Manuals Search And Download.
80
When the SUB STATUS menu item is set to AUDIO
MIXING:
On-screen indication
Example display:
Meaning
12
2
3
34
Input audio channels 3 and
4 are mixed and recorded
on audio channel 4 on tape.
Input audio channel 3 is recorded
on audio channel 3 on tape.
Input audio channel 2 is recorded
on audio channel 2 on tape.
Input audio channels 1 and 2 are mixed and
recorded on audio channel 1 on tape.
Display format of supplementary status
information when the SUB STATUS menu item is
set to ALL
All items of supplementary status information are
displayed in the order shown below.
:
.
T C R
0 0
:
0 4
M I
4 7
0 7
P L A Y
L O C K
X
D
V 1 2 3 4 T
E
T U V
Editing mode settings
Operating mode of the internal
time code generator
(The rightmost “V” appears
when the VITC menu items
(see page 67) is set to ON.)
Setting for input audio mixing
Displaying Supplementary Status Information
Download from Www.Somanuals.com. All Manuals Search And Download.
81
Displaying Supplementary Status Information
Download from Www.Somanuals.com. All Manuals Search And Download.
82
Connections and
Settings Chapter
5
Note
Production of some of the peripherals and related devices
described in this chapter has been discontinued. For advice
about choosing devices, please contact your Sony dealer or
a Sony sales representative.
Connections for a Digital Non-Linear Editing System
This unit can be connected to a nonlinear editor supporting
DV/DVCAM with an i.LINK cable (DV cable). Shown
below is an example of connections to use this unit as a
recorder in a nonlinear editing system.
connection and settings on the nonlinear editing
equipment.
• Different editing software applications provide different
editing functions. For more information about actual
editing procedures and settings, refer to the
documentation of your editing software.
Notes
• Refer to the documentation of your nonlinear editing
equipment and software for more information about
DV IN/OUT
1
VIDEO OUT 2
AUDIO
Nonlinear editing system
DSR-1800A/
1800AP (recorder)
(SUPER)
MONITOR OUT
Composite
video input
2
3
Audio input
A i.LINK cable (DV cable)
(not supplied)
B 75 Ω coaxial cable (not supplied)
C Cable with RCA phono plugs
(not supplied)
Video monitor
Connections for a Digital Non-Linear Editing System
Download from Www.Somanuals.com. All Manuals Search And Download.
83
Settings on the DSR-1800A/1800AP
Button
REMOTE
9PIN
Setting
On (lit)
Off (Unlit)
On (lit)
i.LINK
For details of video/audio input and audio mode settings,
Notes
• When you connect this unit to another device with a 6-
pin DV connector, always power the other device off and
unplug its power cord from the power output before
connecting or disconnecting the i.LINK cable (DV
cable). If you connect or disconnect the cable with the
power cord still plugged in, power from the DV
connector may flow into this unit, possibly damaging
this unit.
• When you connect this unit to another device with a 6-
pin DV connector, make the connection to the 6-pin DV
connector on the other device before making the
connection to this unit.
Connections for a Digital Non-Linear Editing System
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections for a Cut Editing System
The following figure shows a cut editing system
configuration that includes two DSR-1800A/1800AP units
to serve as the player and recorder.
When using a VCR other than the DSR-1800A/1800AP,
refer to its instruction manual.
When you select assemble or insert editing mode on
the editing control unit, the two DSR-1800A/1800AP
units (recorder and player) will automatically enter the
selected editing mode.
A 75 Ω coaxial cable (not supplied)
B 9-pin remote control cable
(not supplied)
C Cable with RCA phono plugs
(not supplied)
1
DSR-1800A/
1800AP (player)
DSR-1800A/
1800AP (recorder)
SDI IN
SDI OUT
REF.
VIDEO
OUT
VIDEO
OUT 2
(SUPER)
AUDIO
MONITOR
OUT
AUDIO
MONITOR
OUT
VIDEO
OUT 2
(SUPER)
REMOTE
REMOTE
1
3
2
1
1
3
2
Composite
video input
Composite
video input
Audio input
Audio input
REF.
VIDEO IN
PLAYER
Source monitor
Main monitor
RECORDER
a)
Editing control unit (PVE-500, etc.)
a) For the settings on the editing control unit, see
Settings on the DSR-1800A/1800APs (recorder
and player)
About reference video signals
In order to provide stable video and audio signals for
analog editing, it is necessary for the built-in time base
corrector (TBC) to operate correctly. To ensure this, input
a reference video signal synchronized with the video signal
to the REF. VIDEO IN connector.
Button
REMOTE
9PIN
Recorder
On (lit)
Player
On (lit)
On (lit)
On (lit)
For details of the video/audio input and audio mode
settings for the recorder, see “Settings for Recording” on
Connections for a Cut Editing System
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections for an A/B Roll Editing System
The following is an example configuration of A/B roll
editing system using the DSR-1800A/1800AP.
The purpose of the following figure is to clearly indicate
the flow of signals among the component devices in this
system. The specific connections and settings are
Main video monitor
Source video monitor
Audio system monitor
DSR-1800A/
1800AP (recorder)
Video signal generator
DPS-D7 or other delay
a)
unit
Audio mixer
(MXP-290, etc.)
Editing control unit
(PVE-500, etc.)
DME switcher
(DFS-500/500P,
etc.)
UVW-1600/1600P,
etc.
DSR-1600A/1600AP (player 1)
(player 2)
Video signal
Audio signal
Reference video signal
Control signal
a) An I/O delay of several frames occurs on DME switchers and
other devices equipped with frame memory. It is therefore
necessary to connect an audio delay unit between the audio
mixer and the recorder VCR to adjust for the delay.
Connections for an A/B Roll Editing System
Download from Www.Somanuals.com. All Manuals Search And Download.
86
Audio monitor system connections
Reference video signal connection
The following shows an example of audio monitor system
connections.
When you perform recording, be sure to input a reference
video signal.
For details of these connections, refer to the instruction
manual for each connected device.
For details of reference video signals, see “About
Speaker (right channel)
Speaker (left channel)
DME switcher
(DFS-500/500P, etc.)
BLACK
BURST
4 3 2 1
OUT
Audio amplifier
DSR-1800A/
1800AP (recorder)
REF. VIDEO IN
R
R
L
L
Cables with RCA phono plugs
MONITOR
OUT 1
MONITOR
OUT 2
DSR-1600A/
1600AP (player 1)
REF. VIDEO IN
Audio mixer (MXP-290, etc.)
REF. VIDEO IN 75 Ω
termination switch: ON
REF. VIDEO IN
UVW-1600/1600P, etc.
(player 2)
Editing control unit
(PVE-500, etc.)
REF.
VIDEO
IN
REF. VIDEO IN 75 Ω termination switch: ON
Use 75 Ω coaxial cables for all of these connections.
Connections for an A/B Roll Editing System
Download from Www.Somanuals.com. All Manuals Search And Download.
87
Control signal connections
The following shows an example of control signal
connections to enable the editing control unit to control all
other A/B roll editing system devices.
DSR-1800A/1800AP (recorder)
REMOTE
9-pin remote control cable (not supplied)
DSR-1600A/1600AP (player 1)
REMOTE
Mixer control mode
selection switch:
PARALLEL
UVW-1600/1600P, etc. (player 2)
RECORDER
PLAYER 1
MIXER
SWITCHER
PLAYER 2
Editing control unit
(PVE-500, etc.)
REMOTE
9-pin remote control cable (not supplied)
DME switcher
(DFS-500/500P, etc.)
EDITOR
9-pin remote control cable (not supplied)
Audio mixer
(MXP-290, etc.)
9-pin/15-pin mixer control cable (not supplied)
EDITOR (15-pin)
Connections for an A/B Roll Editing System
Download from Www.Somanuals.com. All Manuals Search And Download.
88
In this example, analog component signals are used as the
video signals and XLR 3-pin connectors are used as audio
input/output connectors.
Video/audio signal connections
The following shows an example of video/audio signal
connections in an A/B roll editing system.
DSR-1800A/
1800AP (recorder)
COMPONENT VIDEO IN
Y, R–Y, B–Y
1
DME switcher
(DFS-500/500P, etc.)
VIDEO INPUTS
COMPONENT 2
PGM OUT
COMPONENT 1
CH-2
AUDIO IN
CH-1
3
VIDEO INPUTS
COMPONENT 1
1
3
CH-1 OUT
DPS-D7 or other delay unit
CH-1 IN CH-2 IN
CH-2 OUT
2
DSR-1600A/
1600AP (player 1)
COMPONENT VIDEO OUT
Y, R–Y, B–Y
3
3
LINE OUT 2
LINE OUT 1
AUDIO OUT
CH-1
MIC/LINE 4
IN
3
2
1
Audio mixer
(MXP-290, etc.)
CH-2
3
3
3
3
COMPONENT 1
OUTPUT
A 12-pin/3-BNC cross cable
(not supplied; consult your
Sony dealer about this cable.)
B 12-pin dubbing cable
(not supplied)
AUDIO OUTPUT
CH-1
UVW-1600/1600P, etc.
(player 2)
CH-2
C Cable with XLR
connectors (not supplied)
Settings on the DSR-1800A/1800AP (recorder)
For details of the video/audio input and audio mode
Switch/menu
Setting
AUDIO IN LEVEL/600 Ω
HIGH-ON
switches
Connections for an A/B Roll Editing System
Download from Www.Somanuals.com. All Manuals Search And Download.
89
Connection of a video monitor
Settings on an editing control unit
Set up the following connections to enable monitoring of
video and audio signals on a video monitor. In addition to
the video and audio signals, you can have time data, the
operation mode of the unit, alarm messages, and other
information displayed as text on the monitor screen by
setting the CHARA. DISPLAY menu item (see page 65)
to ON (factory default setting).
When connecting an editing control unit, make the settings
as follows, according to the model.
PVE-500
No settings are required.
BVE-600/900/910/2000 (NTSC model) or FXE-100/
120
Set the VCR constants as follows.
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
80 15 00 96 05 05 03 80 0A 08 FE 00 80 5A FF
75 Ω termination switch: ON (or attach a 75
Ω terminator)
Input switches: Set according to the type of
input signals.
BVE-600/900/910/2000 (PAL model) or FXE-100P/
120P
Video monitor
Set the VCR constants as follows.
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
81 15 00 7D 05 05 02 80 0A 07 FE 00 80 4C FF
RM-450/RM-450CE
Set the DIP switches as follows.
• Left switches
Composite
Audio input
7
6
5
4
3
2
1
0
video input
OFF
−
−
OFF
−
−
−
−
2
1
VIDEO
OUT
2(SUPER)
• Right switches (RM-450)
)
AUDIO
MONITOR OUT
7
6
5
4
3
2
1
0
OFF
−
OFF
ON
OFF
OFF
ON
ON
• Right switches (RM-450CE)
7
6
5
4
3
2
1
0
ON
−
OFF
ON
OFF
OFF
ON
ON
BVE-800
Set the DIP switches as follows.
DSR-1800A/1800AP (recorder)
• SW2
1
2
3
4
5
6
7
8
A Cable with RCA phono plugs
ON
OFF
ON
ON
−
ON
ON
−
(not supplied)
• SW3 (NTSC model)
B 75 Ω coaxial cable
(not supplied)
1
2
3
4
5
6
7
8
ON
ON
ON
OFF
−
ON
OFF
OFF
• SW3 (PAL model)
1
2
3
4
5
6
7
8
OFF
OFF
OFF
ON
−
ON
OFF
OFF
Connections for an A/B Roll Editing System
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections for Analog Recording
The following shows connections for a system in which
analog playback signals from another recorder or player
are recorded on a DSR-1800A/1800AP. In this system, the
video signals are analog component signals and the audio
signals are recorded from audio channels 1 and 2.
Video monitor
A Cable with RCA phono plugs
(not supplied)
B 75 Ω coaxial cable
(not supplied)
C Cable with XLR connectors
(not supplied)
Composite
video input
Audio input
2
2
1
2 a)
REF.
VIDEO
OUT
VIDEO
OUT
2(SUPER)
COMPONENT VIDEO OUT
Y,R–Y,B–Y
REF.VIDEO
IN
AUDIO
MONITOR OUT
COMPONENT
VIDEO IN
Y,R–Y,B–Y
AUDIO OUT
CH-1
DSR-1600A/1600AP (player)
CH-2
AUDIO IN
CH-1
DSR-1800A/1800AP (recorder)
CH-2
3
3
a) Three 75 Ω coaxial cables are used,
one each for Y, R−Y, and B−Y.
Settings on the DSR-1800A/1800AP (recorder)
Switch/menu/input/audio
mode
Setting
a)
AUDIO IN LEVEL/600 Ω
switches
HIGH-ON
REMOTE button
Video input
Off (unlit)
Component
Analog
Audio input
Audio mode
2 channel/48 kHz
Connections for Analog Recording
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Sync and Subcarrier Phases
When using two or more players, as in an A/B roll editing
system, it is necessary to synchronize the sync and
subcarrier (for composite signals) phases of the signals to
be edited. If they are not synchronized, picture instabilities
or color break-up may occur at edit points.
After configuring the editing system, use a vectorscope to
adjust the sync and subcarrier phases of the recorder and
players. Subcarrier phase adjustment is necessary when
using composite signals and Y/C signals.
DSR-1600A/1600AP (player 1)
a)
Switcher (DFS-500/500P, etc.)
DSR-1800A/1800AP (recorder)
UVW-1600/1600P, etc. (player 2)
b)
75 Ω coaxial cable (A)
b)
75 Ω coaxial cable (B)
Vectorscope
Editing control unit
(PVE-500, etc.)
a) The sync and subcarrier phases of the
output signal from the DFS-500/500P
switcher are automatically adjusted.
b) Ensure that the 75 Ω coaxial cables (A) and
(B) (not supplied) are of the same length.
Adjusting the Sync and Subcarrier Phases
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing a phase adjustment operation
Note
When component signals are used the subcarrier phase
indicator does not appear.
1 Press the SCH button on the vectorscope.
The vectorscope switches to SCH mode.
8 Output the player 2 signal and repeat steps 6 and 7 to
adjust the sync and subcarrier phases of the output
from player 2.
2 Press the B channel button on the vectorscope.
This displays the black burst signal from the switcher.
Note
Note
The color of video on monitors connected to the composite
and S-video outputs may temporarily change or be
reversed when you rotate the SYNC PHASE control and
SC PHASE control.
3 Press the EXT button on the vectorscope.
This switches the vectorscope to external
synchronization mode.
4 Adjust the phase synchronization control on the
vectorscope so that the sync and subcarrier phases are
close to the reference line.
Sync phase
Subcarrier phase
Reference line
Align the sync and subcarrier phases of the black
burst signal to the reference line.
5 Output the player 1 signal.
6 Press the A channel button on the vectorscope.
This displays the sync and subcarrier phases
(composite signals only) of the signal from player 1.
7 On player 1, adjust the SYNC PHASE and SC PHASE
controls on the menu control panel, using a Phillips
screwdriver, so that the output from player 1 on
channel A is in correct phase alignment with the black
burst signal on channel B.
This indicator
This indicator
moves as you
moves as you
turn the SYNC
turn the SC
PHASE control.
PHASE control.
Adjust the sync and subcarrier phases of the output
signal from player 1.
Adjusting the Sync and Subcarrier Phases
Download from Www.Somanuals.com. All Manuals Search And Download.
93
Adjusting the Sync and Subcarrier Phases
Download from Www.Somanuals.com. All Manuals Search And Download.
94
Maintenance and
Troubleshooting Chapter
6
Regular Checks
Maintenance
Digital hours meter
The digital hours meter keeps cumulative counts of the
total operating time, the head drum rotation time, the tape
transport operating time, and the number of threading/
unthreading operations. These counts can be displayed on
the monitor screen and in the time counter display of this
unit. Use them as guidelines for scheduling maintenance.
In general, consult your Sony dealer about necessary
periodic maintenance checks.
Condensation
If you move the unit suddenly from a cold to a warm
location, or if you use it in a very humid place, moisture
from the air may condense on the head drum. This is called
condensation, and if a tape is run in this state, the tape may
stick to the drum and can be easily damaged. To lessen the
risk of this occurring, this unit is equipped with a
condensation detection system.
Digital hours meter display modes
The digital hours meter has the following four display
modes.
If condensation occurs while the unit is
operating:
• T1 (OPERATION) mode
The alarm message “MOISTURE HAS BEEN
DETECTED.” appears on the monitor screen, and the
alarm message “HUMID!” in the time counter display. At
the same time the unit ejects the cassette automatically. If
this happens, leave the unit powered on and wait until the
alarm messages disappear.
The cumulative total hours during which the unit is
powered on is displayed in 10-hour increments.
• T2 (DRUM ROTATION) mode
The cumulative total hours of drum rotation with tape
threaded is displayed in 10-hour increments.
• T3 (TAPE RUNNING) mode
The cumulative total hours of tape transport operation
for fast forward, rewind, playback, and search (except in
still search mode) is displayed in 10-hour increments.
• CT (THREADING) mode
The cumulative number of tape threading/unthreading
operation pairs is displayed in 10-operation pair
increments.
If the condensation alarm message appears
immediately after powering on:
Leave the unit powered on and wait until the alarm
message disappears. You cannot load a cassette into the
unit while the alarm message is being displayed.
Once the alarm message disappears, the unit is ready for
use.
For all modes except T1 (OPERATION), there are two
types of count: a “trip” count, which is resettable, and the
cumulative total from manufacture, which is unresettable.
Maintenance
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital hours meter indications on the monitor
screen
All four counts (T1, T2, T3, and CT) are indicated on the
monitor screen.
Displaying the digital hours meter
Use the following procedure.
1 Press the MENU button on the menu control panel.
The menu selection level display appears on the
monitor screen and in the time counter display.
Resettable trip counts
Unresettable counts
HOURS METER
Menu selection level display
T1
00000 X10 HOURS
T2 0000/00000 X10 HOURS
T3 0000/00000 X10 HOURS
CT 0000/00000 X10 COUNT
SYSTEM MENU
Setup menu
SETUP MENU
AUTO FUNCTION
Time counter display
HOURS METER
T1:OPERATION
T2:DRUM ROTATION
T3:TAPE RUNNING
CT:THREADING
The four-digit value to the left of the slash (/) is the
resettable trip count, and the right value is the cumulative
total from manufacture.
Monitor screen
2 Press the j button to select “HOURS METER.”
Digital hours meter indications in the time
counter display
SYSTEM MENU
Hours meter
SETUP MENU
One of the four indications appears in the time counter
display at a time. Use the J and j buttons on the menu
control panel to change the item displayed.
Initially, only the trip value appears. Hold down the k
button to display also the cumulative total from
manufacture, which will appear to the right of the trip
value and the slash (/).
AUTO FUNCTION
Time counter display
HOURS METER
The following illustrates the digital hours meter
indications in the time counter display in all four display
modes. The right-hand indication for each display mode is
the indication you can view while holding down the k
button on the menu control panel.
Monitor screen
3 Press the k button.
T1 (OPERATION) mode:
The cumulative counts by the digital hours meter are
indicated on the monitor screen and in the time counter
display.
Oper. 00000
T2 (DRUM ROTATION) mode:
Drum 0000
0000/00000
0000/00000
T3 (TAPE RUNNING) mode:
Tape 0000
CT (THREADING) mode:
Thread 0000
0000/00000
Maintenance
96
Download from Www.Somanuals.com. All Manuals Search And Download.
To end the digital hours meter display
Press the MENU button on the menu control panel.
To reset the trip values
About this operation, consult your Sony dealer.
Head Cleaning
Always use the DVM12CL (mini size) or DV12CL
(standard size) Cleaning Cassette to clean the video and
audio heads. You can run the cleaning cassette for 10
seconds per cleaning operation. Follow the instructions for
the cleaning cassette, as inappropriate use of the cleaning
cassette can damage the heads.
To clean the heads
Insert the cleaning cassette. This automatically starts
cleaning. You cannot operate any tape transport control
buttons other than the EJECT button during the cleaning
operation.
After about 10 seconds, the cleaning cassette will be
automatically ejected.
Maintenance
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If an alarm message appears on the monitor screen, or if
the unit appears to be malfunctioning, please check the
following before contacting your Sony dealer.
Tape problems
Symptom
Cause
Remedy
Recording is not
possible.
The cassette’s REC/SAVE switch is set Set the REC/SAVE switch to REC, or use another cassette.
to SAVE.
a)
The unit’s tape
transport control
buttons (PLAY, F FWD,
REW, etc.) do not
work.
The REMOTE button is lit and the
LOCAL ENABLE menu item is set to
STOP & EJECT or ALL DISABLE.
Press the REMOTE button to turn it off, or change the setting
ENABLE.
a)
a)
No cassette is loaded.
The NOT EDITABLE
indicator on the front
panel lights up.
The audio recording mode selected on • When your current purpose is editing, press the REMOTE
this unit does not coincide with that of
button to turn it off and set the unit for the same audio
recording mode as with the tape using the REC. MODE
button again.
a)
the loaded tape.
• When your current purpose is recording, you can use the
tape currently loaded in the unit.
The recording format of the currently
loaded tape is “DV” or “DVCPRO.”
Replace the tape with one recorded in the DVCAM format.
a)
a) In these states, an alarm message appears on the monitor screen and in the
time counter display.
Time data problems
Symptom
Cause
Remedy
Cannot freely set the
initial time data value.
a)
REGEN.
CNT is selected as the time data type Press the COUNTER SEL button to make the TC or U-BIT
to be displayed (the COUNTER time
data type indicator is lit).
time data type indicator light up (the CNT value cannot be
set freely).
a)
The REMOTE button is lit and the
LOCAL ENABLE menu item is set to
STOP & EJECT or ALL DISABLE.
Press the REMOTE button to turn it off or change the setting
ENABLE.
a)
The tape is running,
but the time data is not button on the menu control panel has
shown in the time
counter display.
The MENU button or TC PRESET
Press the button once again to exit the menu control mode,
time code preset mode, or digital hours meter display mode.
(In either of the menu control mode and time code preset
mode, the time data is not shown in the time counter display.)
been pressed.
The U-BIT time data type indicator is lit. Press the COUNTER SEL button to make the COUNTER or
TC time data type indicator light up.
a) In these states, an alarm message appears on the monitor screen and in the
time counter display.
Monitor problems
Symptom
Cause
Remedy
Data is not
superimposed on the
monitor screen.
The CHARA. DISPLAY menu item is
set to OFF.
The monitor is not connected to the
VIDEO OUT 2 (SUPER) connector of
this unit.
Connect the monitor to the VIDEO OUT 2 (SUPER)
connector. (You must make this connection to display any
type of text on the monitor.)
Troubleshooting
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitor problems
Symptom
Cause
Remedy
The image on the
monitor screen is too
bright.
The 75 Ω termination switch for video
input on the monitor is in the OFF
position, or a 75 Ω terminator is not
fitted to its video input connector.
Set the 75 Ω termination switch to ON or connect a
terminator.
The image on the
monitor screen is too
dark.
In a video signal loop-through
Set the 75 Ω termination switches to OFF on all monitors
other than the loop-end monitor.
connection of video monitors, 75 Ω
termination switches for video input on
monitors other than the loop-end
monitor are in the ON position.
The image is too dark
when recording a
composite video
signal.
Audio problem
Symptom
Cause
Remedy
The AUDIO INPUT
LEVEL control knobs
do not work.
The REC LEVEL menu item is set to
PRESET.
Note
To be able to perform this operation, it is necessary to set the
i.LINK interface problems
Symptom
Cause
Remedy
This unit cannot be
recognized or
controlled by computer It is only guaranteed as a tape dubbing
Performance of i.LINK interface is not
guaranteed with all IEEE 1394 devices.
• Check the computer for connections and setup.
• Contact your computer hardware/software manufacturer to
check system requirements and product compatibility.
via i.LINK interface.
facility between VTRs.
Editing restriction
Symptom
Cause
Execution of video
This phenomenon cannot be avoided with an editing system using this unit as the recorder.
editing in insert mode
erases subcode data
(user bit data, etc.)
recorded on tape other
than time code data.
Troubleshooting
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Messages
This unit is provided with a self-diagnostic function that
detects internal abnormalities. When it detects an
abnormality, it outputs an error message to the monitor
screen and indicates an error code in the time counter
display.
Note
To display error messages on the monitor screen, connect
the monitor to the VIDEO OUT 2 (SUPER) connector, and
ON (factory default setting).
ERROR
AN ERROR HAS BEEN
DETECTED. INFORM SERVICE
OF FOLLOWING CODE:
02-603
Error message
Error code
PRESS EJECT KEY
TO EJECT TAPE.
Direction
Error code
Error02-603
Time counter display
Monitor screen
If an error message appears, follow the direction indicated
on the monitor screen.
Alarm Messages
When operating this unit, the unit may sometimes output
alarm messages such as the one shown below to the
monitor screen and the time counter display.
ALARM
Cause of
alarm
REMOTE MODE IS SELECTED
Direction
PRESS REMOTE BUTTON
TURNING IT OFF
REMOTE!
Time counter display
Monitor screen
If such an alarm message appears, a connection or
operation error may have been made, or condensation on
heads may have occurred. Follow the direction indicated
on the monitor screen.
Note
To display alarm messages on the monitor screen, it is
necessary for the monitor to be connected to the VIDEO
OUT 2 (SUPER) connector, and set the following menu
items to ON.
Troubleshooting
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm messages and associated directions
Direction
Alarm message on monitor screen
(Cause)
Alarm message in time
counter display
A cleaning tape has been inserted.
The tape will automatically be ejected after cleaning is Cleaning Tp
completed.
A non-standard signal is being used for
input video.
Use a standard signal.
VIN NON-STD
A non-standard ref. signal is being used Use a standard signal.
for REF. VIDEO.
REF NON-STD
Abnormal settings selected in setup
menu.
Correct the setup menu settings. Contact your Sony ILL. SETUP!
dealer if this alarm message appears again after
making corrections.
Audio mixing mode cannot be changed
during recording.
−
REC mode!
Audio not editable on this tape.
Use a tape recorded in 2-channel/48 kHz or
4-channel/32 kHz mode.
2CH/32kHz!
Fs 44.1kHz!
Use a tape having audio signals recorded in locked
mode.
UNLOCK mode
Audio REC mode selection different from Select the same audio recording mode as that of the A mode err
audio on tape.
tape.
Audio REC (recording) mode cannot be
changed during recording.
−
REC mode!
Cassette adaptor not usable.
Counter mode is selected.
Use a tape without cassette adaptor.
Adaptor!
Use the COUNTER SEL button to light the TC or U-
BIT time data type indicator in the display section.
CNT mode!
Input selection cannot be changed in
REC (recording) mode.
−
−
−
−
REC mode!
Input signal does not conform to
DVCAM/DV format.
Unknown Sig
Input signal is 625/50. (For DSR-1800A)
625/50 sig! (For DSR-
1800A)
Input signal is 525/60. (For DSR-
1800AP)
525/60 sig! (For DSR-
1800AP)
Input video is not detected.
Check the VIDEO display in the input selection/audio No INPUT!
mode display section and supply an appropriate video
signal.
Input video signal does not synchronize Use a reference video signal or connect the recorder ILL. REF!
with REF. VIDEO signal.
REF. VIDEO OUT connector to the player REF.
VIDEO IN connector.
Note
When connecting the recorder REF. VIDEO OUT
connector to the player REF. VIDEO IN connector, set
FORCED NON-STD.
Moisture has been detected.
Keep the power on and wait until this alarm message HUMID!
disappears.
No cassette in VTR.
Load a cassette.
No Cass.!
Rec inhibit mode is selected.
OFF.
REC INHI.!
Record inhibit plug on the cassette is set Set the REC/SAVE switch on the cassette to REC.
to inhibit.
REC INHI.!
REMOTE!
Remote mode is selected.
Turn off the REMOTE button.
Troubleshooting
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm messages and associated directions
Direction
Alarm message on monitor screen
(Cause)
Alarm message in time
counter display
Tape cannot be replayed.
Use a tape recorded in 525/60 format. (For DSR-
1800A)
625/50 Tape (For DSR-
1800A)
Use a tape recorded in 625/50 format. (For DSR-
1800AP)
525/60 Tape (For DSR-
1800AP)
Tape end has been detected.
Tape not editable.
Use a new cleaning tape.
Tape end!
Use a tape recorded in DVCAM format.
Not DVCAM!
Use a tape recorded in 525/60 format. (For DSR-
1800A)
625/50 Tape (For DSR-
1800A)
Use a tape recorded in 625/50 format. (For DSR-
1800AP)
525/60 Tape (For DSR-
1800AP)
Tape not recordable.
Tape not usable.
Use a DVCAM/DV ME tape.
REC INHI.!
ILL. Tape!
TC EXT!
Use a DVCAM/DV/DVCPRO (25M) tape.
TC EXTERNAL is selected.
PRESET.
TCG REGEN mode is selected.
PRESET.
REGEN mode!
REC RUN!
TCG RUN mode is set to REC RUN.
FREE RUN.
Troubleshooting
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendixes
Avoid violent impacts
Dropping the unit, or otherwise imparting a violent shock
to it, is likely to cause it to malfunction.
Precautions
Do not obstruct ventilation openings
To prevent the unit from overheating, do not obstruct
ventilation openings, by for example wrapping the unit in
a cloth while it is in operation.
On safety
• Should any liquid or solid object fall into the cabinet,
unplug the unit and have it checked by qualified
personnel before operating it further.
• Unplug the unit from the wall outlet if it is not to be used
for an extended period of time.
On cleaning
If the casing or panel is dirty, wipe it gently with a soft dry
cloth. In the event of extreme dirt, use a cloth steeped in a
neutral detergent to remove the dirt, then wipe with a dry
cloth. Applying alcohol, thinners, insecticides, or other
volatile solvents may result in deforming the casing or
damaging the finish.
• To disconnect the cord, pull it out by the plug. Never pull
the cord itself.
On operation and storage locations
Avoid operation or storage in any of the following places.
• Location subject to extremes of temperature (operating
temperature range 5ºC to 40ºC (41ºF to 104ºF))
• Location subject to direct sunlight for long periods, or
close to heating appliances (Note that the interior of a car
left in summer with the windows closed can exceed 50ºC
(122ºF).)
On repacking and shipping
Save the original shipping carton and packing material;
they will come in handy if you ever have to ship your unit.
For maximum protection, repack your unit as it was
originally packed at the factory, and take care not to impart
violent shocks in transit.
• Damp or dusty places
• Location subject to severe vibrations
• Location near equipment generating strong
electromagnetic emissions
• Location near transmitting stations generating strong
radio waves
Operate the unit in a horizontal position
This unit is designed to be operated in a horizontal
position. Do not operate it on its side, or tilted through an
excessive angle (exceeding 20º).
Precautions
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions (w/h/d, excluding projections)
427 × 174 × 400 mm
Specifications
7
7
3
(16 / × 6 / × 15 / inches)
8
8
4
General
427(16 7/8)
Signal system DSR-1800A: NTSC
DSR-1800AP: PAL
Power requirements
100 V to 240 V AC, 50/60 Hz
Power consumption (with all options installed)
DSR-1800A:
100 W/120 V
DSR-1800AP for Europe:
100 W/220 V
DSR-1800AP for USA and Canada:
100 W/120 V
Peak inrush current
(1)Power ON, current probe method:
40 A (100 V), 40 A (240 V)
(2)Hot switching inrush current,
measured in accordance with
European standard EN55103-1:
40 A (230 V)
372(14 3/4)
Operating temperature
5ºC to 40ºC (41ºF to 104ºF)
Storage temperature
Unit: mm (inches)
−20ºC to +60ºC (−4ºF to +140ºF)
Operating relative humidity
Less than 80%
Storage relative humidity
Less than 90%
Tape transport control system
Tape speed
DSR-1800A: 28.193 mm/s
DSR-1800AP: 28.221 mm/s
Mass
13 kg (28 lb 10 oz)
Recording/playback time
Using PDV-184ME standard-size
cassette:
Maximum 184 minutes
Using PDVM-40ME mini-size cassette:
Maximum 40 minutes
Fast forward/rewind time
Using PDV-184ME standard-size
cassette:
Less than 3 minutes
Using PDVM-40ME mini-size cassette:
Less than 1 minute
Search speed
When controlling via RS-422A interface:
Maximum 60 times normal speed in
both directions
When controlling from DSRM-10
Remote Control Unit:
Jog mode: 0 (still) to 2 times normal
speed in both directions
Shuttle mode: 8 speeds from 0 (still) to
16 times normal speed in both
directions
Specifications
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Video performance
Input connectors
Band width
Composite (DSR-1800A):
Digital signal inputs
SDI IN (with optional DSBK-1801 SDI/AES/EBU Input/
Output Board installed)
30 Hz to 4.2 MHz 1.0 dB (Y)
Composite (DSR-1800AP):
25 Hz to 4.8 MHz 1.0 dB (Y)
S-video (DSR-1800A):
30 Hz to 5.0 MHz 1.0 dB (Y),
5.75 MHz +0/−3.0 dB (Y) (TM)
S-video (DSR-1800AP):
BNC type (×2, active-through), Serial
Digital Interface format (270 Mbps),
SMPTE 259M/ITU-R BT.656
DV IN/OUT 6-pin IEEE 1394 connector
25 Hz to 5.0 MHz 1.0 dB (Y),
5.5 MHz +1.0/−2.0 dB (Y),
5.75 MHz +0/−3.0 dB (Y) (TM)
Component (DSR-1800A):
30 Hz to 5.0 MHz 1.0 dB (Y),
5.75 MHz +0/−3.0 dB (Y) (TM),
30 Hz to 1.3 MHz 1.0 dB (C),
1.5 MHz +0/−5.0 dB (C)
Component (DSR-1800AP):
25 Hz to 5.0 MHz 1.0 dB (Y),
5.5 MHz +1.0/−2.0 dB (Y),
5.75 MHz +1.0/−3.0 dB (Y) (TM),
25 Hz to 1.5 MHz 1.0 dB (C),
2.0 MHz +1.0/−2.0 dB (C)
Composite I/O (Y):
Analog video inputs
REF. VIDEO IN
BNC type (×2, loop-through)
Black burst
0.286 Vp-p (DSR-1800A) or 0.3 Vp-p
(DSR-1800AP), 75 Ω, negative sync
Composite sync
VIDEO IN
BNC type (×2, loop-through), composite,
1.0 Vp-p, 75 Ω, sync negative
COMPONENT VIDEO IN
BNC type (×3)
Y: 1.0 Vp-p, 75 Ω, negative sync
R−Y/B−Y: 0.7 Vp-p (75% color bars
for DSR-1800A or 100% color bars for
DSR-1800AP), 75 Ω
S/N
53 dB or more
S VIDEO IN
DIN 4-pin
S-video I/O (Y): 55 dB or more
Component I/O (Y): 55 dB or more
30 ns or less
Y: 1.0 Vp-p, 75 Ω
C: 0.286 Vp-p (DSR-1800A) or
0.3 Vp-p (DSR-1800AP), 75 Ω (burst
level)
Y/C delay
K-factor
2.0% or less (K2T, KPB)
Analog audio inputs
*
Processor adjustment range
AUDIO IN
XLR 3-pin, female (×4), +4/0/−3 /−6
dBu, 600 Ω ON/OFF/−60 dBu, high
impedance, balanced
Video level
Chrome level
Setup/Black level
3 dB/−∞ to 3 dB selectable
3 dB/−∞ to 3 dB selectable
* Selectable on DSR-1800AP only
30 IRE ( 210 mV)
30°
Chroma phase
Y/C delay
Digital audio inputs
100 ns
DIGITAL AUDIO (AES/EBU) IN (with optional DSBK-
1801 SDI/AES/EBU Input/Output Board installed)
BNC type (×2), complying with AES-
3id-1995
*
System phase Sync: 1 μs
SC: 180°
* +2 μs to -3 μs when using a TBC remote control unit
Time code input
TIME CODE IN
Audio performance
BNC type, SMPTE time code (DSR-
1800A) or EBU time code (DSR-
1800AP), 0.5 Vp-p to 18 Vp-p, 3.3 kΩ,
unbalanced
Frequency response
Two-channel (48 kHz) mode:
20 Hz to 20 kHz +0.5 dB/−1.0 dB
Four-channel (32 kHz) mode:
20 Hz to 14.5 kHz +0.5 dB/−1.0 dB
Dynamic range More than 90 dB
Distortion (THD + N)
Output connectors
Digital signal outputs
SDI OUT (with optional DSBK-1801 SDI/AES/EBU
Input/Output Board installed)
Less than 0.05% (48 kHz)
BNC type (×2, active-through), Serial
Digital Interface format (270 Mbps),
SMPTE 259M/ITU-R BT.656
Specifications
105
Download from Www.Somanuals.com. All Manuals Search And Download.
DV IN/OUT 6-pin IEEE 1394 connector
Remote control connectors
REMOTE
D-sub 9-pin, female, for connection of
editing control unit, RS-422A standard
Analog video outputs
REF. VIDEO OUT
BNC type ×1
CONTROL S Stereo minijack, for connection of
SIRCS-compatible remote control unit
(DSRM-10)
Black burst
0.286 Vp-p (DSR-1800A) or 0.3 Vp-p
(DSR-1800AP), 75 Ω, negative sync
Composite sync
VIDEO OUT 1, 2 (SUPER)
VIDEO CONTROL
D-sub 15-pin, male, for connection of
TBC remote control unit
DV IN/OUT 6-pin IEEE 1394 connector
BNC type (×2), composite, 1.0 Vp-p,
75 Ω, sync negative
COMPONENT VIDEO OUT
Supplied accessories
AC power cord (1)
Operating Instructions
English version (1)
CD-ROM manual (1)
BNC type (×3), Y/R−Y/B−Y
Y: 1.0 Vp-p, 75 Ω, sync negative
R−Y: 0.7 Vp-p, 75 Ω (75% color bars for
DSR-1800A or 100% color bars for
DSR-1800AP)
B−Y: 0.7 Vp-p 75 Ω (75% color bars for
DSR-1800A or 100% color bars for
DSR-1800AP)
Optional accessories
DSBK-1801 SDI/AES/EBU Input/Output Board
RCC-5G 9-pin remote control cable (length: 5 m (16 ft))
RMM-131/1 Rack Mount Kit
S VIDEO OUT DIN 4-pin
Digital video cassette
Y: 1.0 Vp-p, 75 Ω, sync negative
C: 0.286 Vp-p (DSR-1800A) or 0.3 Vp-p
(DSR-1800AP), 75 Ω (burst level)
Standard size: PDV-34*/64*/94*/124*/
a)
184*
a)
Mini size: PDVM-12*/22*/32*/40*
Analog audio outputs
a) The * in each model name is actually “ME”
(indicating that a cassette memory is contained), or
“N” (indicating that no cassette memory is
contained).
*
AUDIO OUT XLR 3-pin, male (× 4), +4/0/−3 /−6 dBu,
600 Ω loading, low impedance,
balanced
Cleaning cassette
AUDIO MONITOR OUT
Phono jack, 47 kΩ, unbalanced
−∞ to −11 dBu 1 dBu, −20 dBFS
(DSR-1800A)
DV12CL (standard size), DVM12CL
(mini size)
Design and specifications are subject to change without
notice.
−∞ to −9 dBu 1 dBu, −18 dBFS
(DSR-1800AP)
Notes
* Selectable on DSR-1800AP only
• Always make a test recording, and verify that it was
recorded successfully.
Digital audio outputs
SONY WILL NOT BE LIABLE FOR DAMAGES OF
ANY KIND INCLUDING, BUT NOT LIMITED TO,
COMPENSATION OR REIMBURSEMENT ON
ACCOUNT OF FAILURE OF THIS UNIT OR ITS
RECORDING MEDIA, EXTERNAL STORAGE
SYSTEMS OR ANY OTHER MEDIA OR
STORAGE SYSTEMS TO RECORD CONTENT OF
ANY TYPE.
DIGITAL AUDIO (AES/EBU) OUT (with optional
DSBK-1801 SDI/AES/EBU Input/Output Board installed)
BNC type (×2), complying with AES-
3id-1995
Output for headphones
HEADPHONES
Stereo phone jack, 8 Ω, unbalanced
−∞ to −13 dBu, −20 dBFS
(DSR-1800A)
• Always verify that the unit is operating properly before
use.
−∞ to −11 dBu, −18 dBFS
(DSR-1800AP)
SONY WILL NOT BE LIABLE FOR DAMAGES OF
ANY KIND INCLUDING, BUT NOT LIMITED TO,
COMPENSATION OR REIMBURSEMENT ON
ACCOUNT OF THE LOSS OF PRESENT OR
PROSPECTIVE PROFITS DUE TO FAILURE OF
THIS UNIT, EITHER DURING THE WARRANTY
PERIOD OR AFTER EXPIRATION OF THE
WARRANTY, OR FOR ANY OTHER REASON
WHATSOEVER.
Time code output
TIME CODE OUT
BNC type, SMPTE time code (DSR-
1800A), EBU time code (DSR-
1800AP), 2.2 Vp-p 3 dB, 600 Ω,
unbalanced
Specifications
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Drop frame mode
Non-drop frame mode
Time code runs at 30 frames/sec. The
NTSC system, however, runs at
about 29.97 frames/sec. Drop frame
mode adjusts this difference. The
time code and video are synchronized
by dropping the first two frames of
the time code every minute, except at
the ten-minute marks.
The number of frames of the time
code and video run is not adjusted.
When you use the time code in non-
drop frame mode, the real playback
time will be about 86 seconds shorter
per day than the time code. If you edit
frame by frame or if you determine
the length of a shot by counting the
time code, use drop frame mode.
Glossary
A/B roll editing
An editing method that uses two or
more playback VCRs to create
special effects such as dissolve and
wipe, and uses one record VCR to
record the results of the editing.
Using an editing control unit allows
efficient control of the VCRs and
very precise editing.
EE mode
EE is an abbreviation of “Electric to
Electric”. Video and audio signals are
supplied to the VCR’s internal
circuits, but not to the recording
heads.
Non-linear editing
Editing while playing back video and
audio signals recorded on hard disks.
Video scenes stored on disk can be
cued up quickly, for increased editing
editing.”
AES/EBU format
A unified format for digital audio
signals. It allows a single connector
to carry the signals for two channels.
Head drum
A metal cylinder to which a video
head is attached. This drum is rotated
at high speeds in synchronization
with the sync signal during recording
and playback.
PCM audio
B−Y signal
This is an audio signal represented by
pulse code modulation. The analog
audio signal is first broken down into
a sequence of pulses, and these are
then represented digitally.
A chrominance signal determined by
subtracting the Y (luminance) signal
from the B (blue) signal. One of the
component signals.
Linear editing
Editing while playing back video and
audio signals recorded on video tape.
Capstan
Preroll
A drive mechanism that moves the
tape at a specified speed. Its rotation
normally synchronizes with a
reference sync signal.
Running of a video tape to a prior to
an edit-start point to enable the tape
to reach a steady speed and to be
synchronized with other video tapes.
Loading
When being loaded, the tape is pulled
out of the cassette case and threaded
along the specified tape path and
wrapped round the drum to be ready
for recording or playback. Generally,
this is done automatically when you
place the cassette at the cassette
entrance of the VCR. Also called
threading.
Chrominance signal
R−Y signal
Color signal containing color
information such as hue and
saturation. Also called C signal.
A chrominance signal determined by
subtracting the Y (luminance) signal
from the R (red) signal. One of the
component signals.
Component signals (YRB)
A video signal consisting of a
luminance signal (Y) and two
chrominance signals (R−Y, B−Y).
Reference video signal
A video signal consisting of a sync
signal or sync and burst signals, used
as a reference.
Loop-through connection
A connection which allows a signal
input to an input connector to pass
through the unit and exit from an
output connector as input to external
equipment. Also called bridging
connection.
Composite signal
A composite video signal containing
video, burst and sync signals.
Setup (for DSR-1800A)
The difference between the reference
black level and the blanking level of
a composite signal.
Condensation
Condensation of moisture on the tape
transport mechanisms of VCRs
including the head drum. If moisture
condenses on the head drum, the tape
adheres to the drum and causes
malfunction.
SMPTE
Luminance signal
Abbreviation of Society of Motion
Picture and Television Engineers, a
professional association established
in the USA.
The signal that determines the
brightness of the picture. Also called
Y signal. One of the component
signals.
Glossary
107
Download from Www.Somanuals.com. All Manuals Search And Download.
S/N
Superimpose
Abbreviation of Signal-to-Noise
(ratio). The higher the S/N value, the
less noise and higher the picture
quality.
To put a set of characters onto a
picture so that both can be seen at the
same time.
S-video
Search mode
A signal format in which Y
(luminance) and C (chrominance)
signals are separated to reduce
interference between them so that
noiseless images are reproduced.
A VCR operating mode used when
searching for specific scenes, by
viewing the video output or time code
values while playing back the tape at
various speeds in forward or reverse
direction.
Sync signal
A reference signal consisting of
vertical and horizontal sync signals
used for synchronizing the scanning
patterns of the video camera and the
monitor.
Servo lock
Synchronizing the drum rotation
phase and tape transport phase with a
reference signal during playback and
recording so that the video heads scan
the tape in the same pattern during
playback and recording.
TBC
Abbreviation of Time Base
Corrector. Electronic circuits to
electrically stabilize the playback
signals by removing color variation
and roll in the playback picture
caused by irregularity in drum
rotation and tape movement. Time
base correction reduces deterioration
of picture quality when transmitting
or copying playback signals.
Standby Off mode
One of two conditions in the stop
mode. The drum does not rotate and
tape is slackened. There is no damage
to the video heads and the tape, but
the VCR is not ready for immediate
recording or playback.
Standby On mode
One of two conditions in the stop
mode. The drum is rotating and the
tape is wrapped round the drum. The
VCR is ready for recording or
playback, so a still picture can be
obtained.
Threading
See “Loading.”
Time code
Signals recorded on the tape to
supply information on tape position
such as the hour, minute, second and
frame, to assist in setting edit points
or searching for particular scenes.
Subcarrier
A sine wave imposed on the
luminance portion of a video signal
and modulated to carry color
information. Its amplitude represents
color saturation and its phase
represents hue.
Unloading
When the EJECT button is pressed,
the VCR automatically winds the
tape back into the cassette case. Also
called “Unthreading.”
User bits
Sections of time code information
consisting of a total of 32 bits that can
be used for recording information
such as date, tape ID number,
program ID number, etc.
Glossary
108
Download from Www.Somanuals.com. All Manuals Search And Download.
for digital non-linear editing
system 83
Index
H
Numerics
for dubbing via i.LINK interface
55
I
A
Analog audio signal input/output
Input selection/audio mode display
section 14
Analog video signal input/output
D
DIGITAL AUDIO (AES/EBU) IN
AUDIO IN CH-1 to CH-4 connectors
AUDIOINLEVEL/600-ohmswitches
AUDIO INPUTLEVELcontrol knobs
AUDIO MONITOR OUT connector
AUDIO OUT CH-1 to CH-4
AUTO FUNCTION execution menu
DIGITAL AUDIO (AES/EBU) OUT
J
indications in the time counter
M
DSBK-1801 SDI/AES/EBU Input/
B
E
N
VIDEO OUTPUT PHASE mode
74
C
O
CHANNEL CONDITION indicators
COMPONENT VIDEO IN Y/R-Y/B-
COMPONENT VIDEO OUT Y/R-Y/
P
F
Index
109
Download from Www.Somanuals.com. All Manuals Search And Download.
W
R
Recording/playback format indicators
T
Time code
Time data
S
U
V
VIDEO OUT 1 and 2 (SUPER)
connectors 23
OPERATIONAL FUNCTION
62
Index
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed in China
Sony Corporation
http://www.sony.net/
Download from Www.Somanuals.com. All Manuals Search And Download.
|