2-686-263-11(2)
DVD Recorder
Operating Instructions
To find out useful hints, tips and information about Sony products and
services please visit: www.sony-europe.com/myproduct
RDR-HX520/HX720
RDR-HX722/HX920
© 2006 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
• Do not attempt to replace or
upgrade the hard disk by
yourself, as this may result in
malfunction.
On placement
• Place the recorder in a location
with adequate ventilation to
prevent heat build-up in the
recorder.
Precautions
This equipment has been tested
and found to comply with the
limits set out in the EMC
Directive using a connection
cable shorter than 3 metres.
If the hard disk drive should
malfunction, you cannot recover
lost data. The hard disk drive is
only a temporary storage space.
• Do not place the recorder on a
soft surface such as a rug that
might block the ventilation
holes.
• Do not place the recorder in a
confined space such as a
bookshelf or similar unit.
• Do not place the recorder in a
location near heat sources, or
in a place subject to direct
sunlight, excessive dust, or
mechanical shock.
About repairing the hard
disk drive
On safety
Should any solid object or liquid
fall into the cabinet, unplug the
recorder and have it checked by
qualified personnel before
operating it any further.
• The contents of the hard disk
drive may be checked in case
of repair or inspection during a
malfunction or modification.
However, the contents will not
be backed up or saved by
Sony.
About the hard disk drive
The hard disk has a high storage
density, which enables long
recording durations and quick
access to the written data.
However, it can easily be
damaged by shock, vibration or
dust, and should be kept away
from magnets. To avoid losing
important data, observe the
following precautions.
• Do not apply a strong shock to
the recorder.
• Do not place the recorder in a
location subject to mechanical
vibrations or in an unstable
location.
• Do not place the recorder on
top of a hot surface, such as a
VCR or amplifier (receiver).
• Do not use the recorder in a
place subject to extreme
changes in temperature
(temperature gradient less than
10 °C/hour).
• Do not move the recorder with
its mains lead connected.
• Do not disconnect the mains
lead while the power is on.
• When disconnecting the mains
lead, turn off the power and
make sure that the hard disk
drive is not operating (the
clock is displayed in the front
panel display for at least 30
seconds and all recording or
dubbing has stopped).
• Do not place the recorder in an
inclined position. It is
• If the hard disk needs to be
formatted or replaced, it will
be done at the discretion of
Sony. All contents of the hard
disk drive will be erased,
including contents that violate
copyright laws.
designed to be operated in a
horizontal position only.
• Keep the recorder and discs
away from equipment with
strong magnets, such as
microwave ovens, or large
loudspeakers.
• Do not place heavy objects on
the recorder.
On power sources
• The recorder is not
disconnected from the AC
power source (mains) as long
as it is connected to the wall
outlet, even if the recorder
itself has been turned off.
• If you are not going to use the
recorder for a long time, be
sure to disconnect the recorder
from the wall outlet. To
On recording
Make trial recordings before
making the actual recording.
On compensation for lost
recordings
Sony is not liable and will not
compensate for any lost
recordings or relevant losses,
including when recordings are
not made due to reasons
including recorder failure, or
when the contents of a recording
are lost or damaged as a result of
recorder failure or repair
undertaken to the recorder. Sony
will not restore, recover, or
replicate the recorded contents
under any circumstances.
disconnect the AC power cord
(mains lead), grasp the plug
itself; never pull the cord.
• Do not move the recorder for
one minute after you have
unplugged the mains lead.
,continued
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyrights
About this manual
• Television programmes, films,
video tapes, discs, and other
materials may be copyrighted.
Unauthorized recording of
such material may be contrary
to the provisions of the
Check your model name
The instructions in this
manual are for 4 models:
RDR-HX520, RDR-HX720,
RDR-HX722 and RDR-
HX920. Check your model
name by looking at the front
panel of the recorder.
copyright laws. Also, use of
this recorder with cable
television transmission may
require authorization from the
cable television transmitter
and/or programme owner.
• This product incorporates
copyright protection
technology that is protected by
U.S. patents and other
intellectual property rights.
Use of this copyright
protection technology must be
authorized by Macrovision,
and is intended for home and
other limited viewing uses
only unless otherwise
• In this manual, the internal
hard disk drive is written as
“HDD,” and “disc” is used as a
general reference for the HDD,
DVDs, or CDs unless
otherwise specified by the text
or illustrations.
• Icons, such as
, listed
DVD
at the top of each explanation
indicate what kind of media
can be used with the function
being explained.
• Instructions in this manual
describe the controls on the
remote. You can also use the
controls on the recorder if they
have the same or similar
names as those on the remote.
• The on-screen display
authorized by Macrovision.
Reverse engineering or
disassembly is prohibited.
Copy guard function
Since the recorder has a copy
guard function, programmes
received through an external
tuner (not supplied) may contain
copy protection signals (copy
guard function) and as such may
not be recordable, depending on
the type of signal.
illustrations used in this
manual may not match the
graphics displayed on your TV
screen.
• The explanations regarding
DVDs in this manual refer to
DVDs created on this recorder.
The explanations do not apply
to DVDs that are created on
other recorders and played
back on this recorder.
IMPORTANT NOTICE
Caution: This recorder is
capable of holding a still
video image or on-screen
display image on your
television screen
indefinitely. If you leave the
still video image or on-
screen display image
displayed on your TV for an
extended period of time you
risk permanent damage to
your television screen.
Plasma display panels and
projection televisions are
especially susceptible to this.
If you have any questions or
problems concerning your
recorder, please consult your
nearest Sony dealer.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Playable discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Hooking Up the Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Step 5: Preparing the Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
If you have a Sony DVD player or more than one Sony
DVD recorder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Step 6: Easy Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Connecting a decoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Eight Basic Operations — Getting to Know Your DVD Recorder
2. Recording a Programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
6. Labelling and Protecting a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Unfinalising a disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
,continued
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Unrecordable pictures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Recording TV programmes using the VIDEO Plus+ system
(RDR-HX520/HX720 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Creating chapters in a title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Playing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Playback options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Adjusting the picture quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Playing from the beginning of the programme you are recording
(Chasing Playback). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Playing a previous recording while making another
(Simultaneous Rec and Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Dividing a title (Divide) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Before Dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Before DV Dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Channel Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Video Settings (Video) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Audio Settings (Audio) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Recording Settings (Recording) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Disc Settings (DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Notes About This Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
About i.LINK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Guide to Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Language Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Area Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Guide to Disc Types
Recordable and playable discs
Icon used in Formatting
this manual (new discs)
Compatibility with other DVD
players (finalising)
Type
Disc Logo
Hard disk drive
(internal)
Formatting
unnecessary
Dub HDD contents to a DVD
to play on other DVD players
HDD
Automatically
formatted in
+VR mode
(DVD+RW
VIDEO)
Playable on DVD+RW
compatible players
(automatically finalised)
DVD+RW
+
RW
Playable only on VR mode
compatible players
(finalisation unnecessary)
VR
mode
Format in VR
mode (page 27)
-
RWVR
DVD-
RW
Format in
Video mode
Playable on most DVD
players (finalisation
necessary) (page 36)
Video
mode
-
RWVideo
DVD+R
Automatically
formatted in
+VR mode
(DVD+R
Playable on most DVD
players (finalisation
necessary) (page 36)
+
R
VIDEO)
DVD+R DL
Format in VR
mode
*1
Playable only on DVD-R in
VR mode compatible players
(finalisation necessary)
VR
mode
Formatting is
performed
-
RVR
Information”
DVD-R
display.
Automatically Playable on most DVD
Video
mode
formatted in
Video mode
players (finalisation
necessary) (page 36)
-
RVideo
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Usable disc versions (as of March 2006)
• 8x-speed or slower DVD+RWs
• 6x-speed or slower DVD-RWs (Ver.1.1,
*2
Ver.1.2 with CPRM
)
• 16x-speed or slower DVD+Rs
• 16x-speed or slower DVD-Rs (Ver.2.0,
*2
Ver.2.1 with CPRM
)
• 8x-speed or slower DVD+R DL (Double
Layer) discs
“DVD+RW,” “DVD-RW,” “DVD+R,” “DVD+R
DL,” and “DVD-R” are trademarks.
*1
When an unformatted DVD-R is inserted into
this recorder, it is automatically formatted in
Video mode. To format a new DVD-R in VR
mode, format using the “Disc Information”
*2
CPRM (Content Protection for Recordable
Media) is a coding technology that protects
copyrights for images.
Discs that cannot be recorded on
• 8 cm discs
• DVD-R DL (Dual Layer) discs
,continued
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Playable discs
Icon used in
this manual
Type
Disc Logo
Characteristics
Discs such as movies that can be
purchased or rented
DVD VIDEO
This recorder also recognizes DVD-R
Dual Layer (Video mode) discs as DVD
Video compatible discs.
DVD
VIDEO CDs or CD-Rs/CD-RWs in
VIDEO CD/Super VIDEO CD format
VIDEO CD
CD
VCD
CD
Music CDs or CD-Rs/CD-RWs in
music CD format
DVD+RWs/DVD+Rs/DVD-RWs/
DVD-Rs/DVD-ROMs containing
JPEG image files
DATA DVD
—
—
DATA DVD
DATA CD
CD-ROMs/CD-Rs/CD-RWs
containing either MP3 audio tracks or
JPEG image files
DATA CD
8 cm DVD+RW, DVD-RW, and
DVD-R recorded with a DVD video
camera
(Still images recorded with a DVD
video camera cannot be played.)
8 cm DVD+RW/
DVD-RW/DVD-R
—
—
“DVD VIDEO” and “CD” are trademarks.
Discs that cannot be played
• PHOTO CDs
• CD-ROMs/CD-Rs/CD-RWs that are
recorded in a format different from the
formats mentioned in the table above.
• Data part of CD-Extras
• DVD-ROMs/DVD+RWs/DVD-RWs/
DVD+Rs/DVD-Rs that do not contain
DVD Video or JPEG image files.
• DVD Audio discs
• DVD-RAMs
• HD layer on Super Audio CDs
• DVD VIDEOs with a different region code
(page 11).
• DVDs that were recorded on a different
recorder and not correctly finalised.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Maximum recordable number of titles
Note on DualDiscs
A DualDisc is a two sided disc product which
mates DVD recorded material on one side
with digital audio material on the other side.
However, since the audio material side does
not conform to the Compact Disc (CD)
standard, playback on this product is not
guaranteed.
Disc
Number of titles*
HDD
300
99
DVD-RW/DVD-R
DVD+RW/DVD+R
DVD+R DL
49
49
* The maximum length for one title is eight hours.
b Notes
• Some DVD+RWs/DVD+Rs, DVD-RWs/DVD-
Rs, or CD-RWs/CD-Rs cannot be played on this
recorder due to the recording quality or physical
condition of the disc, or the characteristics of the
recording device and authoring software. The
disc will not play if it has not been correctly
finalised. For more information, see the operating
instructions for the recording device.
• You cannot mix VR mode and Video mode on the
same DVD-RW. To change the disc’s format,
contents will be erased after reformatting.
• You cannot shorten the time required for
recording even with high-speed discs.
• It is recommended that you use discs with “For
Video” printed on their packaging.
• You cannot add new recordings to DVD+Rs,
DVD-Rs, or DVD-RWs (Video mode) that
contain recordings made on other DVD
equipment.
Note on playback operations of DVD
VIDEOs/VIDEO CDs
Some playback operations of DVD VIDEOs/
VIDEO CDs may be intentionally set by
software producers. Since this recorder plays
DVD VIDEOs/VIDEO CDs according to the
disc contents the software producers
designed, some playback features may not be
available. See the instructions supplied with
the DVD VIDEOs/VIDEO CDs.
Region code (DVD VIDEO only)
Your recorder has a region code printed on
the rear of the unit and will only play DVD
VIDEOs (playback only) labelled with
identical region codes. This system is used to
protect copyrights.
DVD VIDEOs labelled
on this recorder.
will also play
• In some cases, you may not be able to add new
recordings to DVD+RWs that contain recordings
made on other DVD equipment. If you do add a
new recording, note that this recorder will rewrite
the DVD menu.
• You cannot edit recordings on DVD+RWs,
DVD-RWs (Video mode), DVD+Rs, or DVD-Rs
that are made on other DVD equipment.
• If the disc contains PC data unrecognizable by
this recorder, the data may be erased.
ALL
If you try to play any other DVD VIDEO, the
message “Playback prohibited by region
code.” will appear on the TV screen.
Depending on the DVD VIDEO, no region
code indication may be labelled even though
playing the DVD VIDEO is prohibited by
area restrictions.
• You may not be able to record on some
recordable discs, depending on the disc.
Region code
Music discs encoded with copyright
protection technologies
This product is designed to play back discs
that conform to the Compact Disc (CD)
standard.
Recently, various music discs encoded with
copyright protection technologies are being
marketed by some record companies. Please
be aware that among those discs, there are
some that do not conform to the CD standard
and may not be playable by this product.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Hookups and Settings
Hooking Up the Recorder
Follow steps 1 through 6 to hook up and adjust the settings of the recorder. Do not connect the
b Notes
• Plug in cords securely to prevent unwanted noise.
• Refer to the instructions supplied with the components to be connected.
• You cannot connect this recorder to a TV that does not have a SCART or video input jack.
• Be sure to disconnect the mains lead of each component before connecting.
Step 1: Connecting the Aerial Cable
Connect the aerial cable by following the steps below.
to AERIAL IN
DVD recorder
TV
to AERIAL OUT
Aerial cable (supplied)
: Signal flow
1 Disconnect the aerial cable from your TV, and connect it to AERIAL IN on the rear
panel of the recorder.
2 Connect AERIAL OUT of the recorder to the aerial input of your TV using the supplied
aerial cable.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2: Connecting the Video Cords
Select one of the following patterns, A through D, according to the input jack on your TV
monitor, projector, or AV amplifier (receiver). This will enable you to view pictures.
INPUT
B
A
VIDEO
Audio/video cord
(not supplied)
L
AUDIO
TV
R
TV, projector, or AV
amplifier (receiver)
SCART cord
(not supplied)
(yellow)
to LINE 2 OUT (VIDEO)
to i LINE 1 – TV
(blue)
(green)
(red)
DVD recorder
to LINE 2 OUT (S VIDEO)
COMPONENT
VIDEO IN
D
(green)
to
COMPONENT
VIDEO OUT
C
INPUT
Y
S VIDEO
PB/CB
PR/CR
(blue)
(red)
Component
video cord
S-video cord
(not supplied)
TV, projector, or AV
amplifier (receiver)
(not supplied)
TV, projector, or AV
amplifier (receiver)
: Signal flow
A SCART input jack
D Component video input jacks (Y, PB/CB,
PR/CR)
You will enjoy accurate colour reproduction
and high quality images.
If your TV accepts progressive 525p/625p
format signals, you must use this connection
and set “Component Out” in the “Video”
When you set “Easy Setup - Line1 Output” to
SCART cord that conforms to the selected
signal.
B Video input jack
You will enjoy standard quality images.
“Progressive Output” to “On” in the “Video”
setup to send progressive video signals. For
C S VIDEO input jack
You will enjoy high quality images.
,continued
13
Download from Www.Somanuals.com. All Manuals Search And Download.
• One Touch Menu
When playing “wide screen” images
Some recorded images may not fit your TV
screen. To change the picture size, see
You can turn on the recorder and TV, set the
TV to the recorder’s programme position,
and display the Title List menu with one
• One Touch Timer
If you are connecting to a VCR
You can turn on the recorder and TV, set the
TV to the recorder’s programme position,
and display the timer programming menu
with one touch of the TIMER button
Connect your VCR to the LINE 3/
b Notes
• Do not connect more than one type of video cord
between the recorder and your TV at the same
time.
• Automatic Power Off
The recorder will turn off automatically if
the recorder is not used after you turn off
the TV.
• When you connect the recorder to your TV via the
SCART jacks, the TV’s input source is set to the
recorder automatically when you start playback.
If necessary, press TV t to return the input to
the TV.
• For correct SMARTLINK connection, you will
need a SCART cord that has the full 21 pins.
Refer to your TV’s instruction manual as well for
this connection.
• NexTView Download
You can easily set the timer by using the
NexTView Download function on your TV.
See your TV’s instruction manual.
*1
“MEGALOGIC” is a registered trademark of
• If you connect this recorder to a TV with
SMARTLINK, set “Easy Setup - Line1 Output”
to “Video.”
Grundig Corporation.
“EASYLINK” and “CINEMALINK” are
*2
trademarks of Philips Corporation.
“Q-Link” and “NexTView Link” are trademarks
*3
of Panasonic Corporation.
“EURO VIEW LINK” is a trademark of Toshiba
*4
About the SMARTLINK
features (for SCART
connections only)
Corporation.
“T-V LINK” is a trademark of JVC Corporation.
*5
z Hint
SMARTLINK also works with TVs or other
equipment having EPG Timer Control, EPG Title
Download, and Now Recording functions. For
details, refer to the operating instructions supplied
with your TV or other equipment.
If the connected TV (or other connected
equipment such as a set top box) complies
*3
with SMARTLINK, NexTView Link
,
*1
*2
MEGALOGIC , EASYLINK
,
*2
*3
CINEMALINK , Q-Link , EURO VIEW
*4
*5
LINK , or T-V LINK , you can enjoy the
following SMARTLINK features.
• Preset Download
b Notes
• The SMARTLINK features are available only
when “Video” is selected in “Line1 Output.”
• The power must be turned on to use all
SMARTLINK features except One Touch Play,
One Touch Menu and One Touch Timer.
• Not all TVs respond to the functions above.
You can download the tuner preset data
from your TV to this recorder, and tune the
recorder according to that data in “Easy
Setup.” This greatly simplifies the “Easy
Setup” procedure. Be careful not to
disconnect the cables or exit the “Easy
Setup” function during this procedure
• TV Direct Rec
You can easily record what you are
• One Touch Play
You can turn on the recorder and TV, set the
TV’s input to the recorder, and start
playback with one touch of the H (play)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3: Connecting the Audio Cords
Select one of the following patterns, A or B, according to the input jack on your TV monitor,
projector, or AV amplifier (receiver). This will enable you to listen to sound.
[Speakers]
Rear (L)
[Speakers]
Rear (R)
A
AV amplifier (receiver)
with a decoder
Front (L)
Front (R)
Centre
Subwoofer
to coaxial digital input
Coaxial digital cord (not supplied)
to DIGITAL OUT (COAXIAL)
DVD recorder
to LINE 2 OUT (R-AUDIO-L)
INPUT
VIDEO
B
Audio/video cord
(not supplied)
(white)
(yellow)
(white)
(red)
L
(red)
AUDIO
R
(yellow)*
TV, projector, or AV
amplifier (receiver)
: Signal flow
A Digital audio input jack
B Audio L/R (left/right) input jacks
This connection will use your TV’s or stereo
amplifier’s (receiver’s) two speakers for
sound.
*1
If your AV amplifier (receiver) has a Dolby
*2
Digital, DTS , or MPEG audio decoder and
a digital input jack, use this connection. You
can enjoy Dolby Digital (5.1ch), DTS
(5.1ch), and MPEG audio (5.1ch) surround
effects.
,continued
15
Download from Www.Somanuals.com. All Manuals Search And Download.
z Hint
For correct speaker location, see the operating
instructions supplied with the connected
components.
Step 4: Connecting the
Mains Lead
b Notes
• Do not connect your TV’s audio output jacks to
the LINE IN (R-AUDIO-L) jacks at the same
time. This will cause unwanted noise to come
from your TV’s speakers.
Connect the supplied mains lead to the AC IN
terminal of the recorder. Then plug the
recorder and TV mains leads (power cords)
into the mains. After you connect the mains
lead, you must wait for a short while
before operating the recorder. You can
operate the recorder once the front panel
display lights up and the recorder enters
standby mode.
• With connection B, do not connect the LINE IN
(R-AUDIO-L) and LINE 2 OUT (R-AUDIO-L)
jacks to your TV’s audio output jacks at the same
time. This will cause unwanted noise to come
from your TV’s speakers.
• With connection A, after you have completed the
connection, make the appropriate settings under
Otherwise, no sound or a loud noise will come
from your speakers.
If you connect additional equipment to this
mains lead after all connections are complete.
*1
Manufactured under license from Dolby
Laboratories.
“Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Out” are trademarks of
~ IN
*2
1
to AC IN
to mains
Digital Theater Systems, Inc.
2
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling TVs with the
remote
Step 5: Preparing the
Remote
You can adjust the remote’s signal to control
your TV.
You can control the recorder using the
supplied remote. Insert two R6 (size AA)
batteries by matching the 3 and # ends on
the batteries to the markings inside the
battery compartment. When using the
b Notes
• Depending on the connected unit, you may not be
able to control your TV with some or all of the
buttons below.
remote, point it at the remote sensor
recorder.
on the
• If you enter a new code number, the code number
previously entered will be erased.
Number
buttons
TV/DVD
b Notes
• If the supplied remote interferes your other Sony
DVD recorder or player, change the command
• Use the batteries correctly to avoid possible
leakage and corrosion. Should leakage occur, do
not touch the liquid with bare hands. Observe the
following:
TV [/1
TV 2 +/–
– Do not use a new battery with an old battery, or
batteries of different manufacturers.
TV t
TV PROG
+/–
– Do not attempt to recharge the batteries.
– If you do not intend to use the remote for an
extended period of time, remove the batteries.
– If battery leakage occurs, wipe out any liquid
inside the battery compartment, and insert new
batteries.
1 Hold down the TV [/1 button located
at the bottom of the remote.
Do not press the [/1 button at the top of
the remote.
• Do not expose the remote sensor (marked
the front panel) to strong light, such as direct
on
sunlight or a lighting apparatus. The recorder may
not respond to the remote.
• When you replace the batteries of the remote, the
code number and Command Mode may be reset
to the default setting. Set the appropriate code
number and Command Mode again.
,continued
17
Download from Www.Somanuals.com. All Manuals Search And Download.
2 With the TV [/1 button pressed down,
enter the TV’s manufacturer code
using the number buttons.
If you have a Sony DVD player
or more than one Sony DVD
recorder
For instance, to enter “09,” press “0” then
“9.” After you enter the last number,
release the TV [/1 button.
If the supplied remote interferes with your
other Sony DVD recorder or player, set the
command mode number for this recorder and
the supplied remote to one that differs from
the other Sony DVD recorder or player after
The default command mode setting for this
recorder and the supplied remote is DVD3.
Code numbers of controllable TVs
If more than one code number is listed,
try entering them one at a time until you
find the one that works with your TV.
Manufacturer
Sony
Code number
01 (default)
Hitachi
24
JVC
33
Number
buttons
Panasonic
Philips
17, 49
06, 08
71
Samsung
Sanyo
SYSTEM
MENU
25
Thomson
Toshiba
43
M/m,
ENTER
38
The remote performs the following:
Buttons
Operations
TV [/1
Turns your TV on or
off
has been finished. If “Easy Setup” has
not been finished, first perform “Easy
Setup.”
TV 2 (volume) Adjusts the volume
+/–
of your TV
TV PROG +/–
Selects the
programme position
on your TV
2 Press SYSTEM MENU.
The System Menu appears.
TV t
Switches your TV’s
input source
3 Select “SETUP,” and press ENTER.
To operate the TV/DVD button
(for SCART connections only)
The TV/DVD button switches between the
recorder and the last input source selected on
the TV. Point your remote at the recorder
when using this button.
When you connect the recorder to the TV via
the SCART jacks, the input source for the TV
is set to the recorder automatically when you
start playback. To watch another source,
press the TV/DVD button to switch the TV’s
input source.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Select “Others,” and press ENTER.
If the Command Mode for the recorder has
not been changed, set the Command Mode
for the remote to the default setting of
DVD3. If the Command Mode for the
remote is changed to DVD1 or DVD2, you
will be unable to operate this recorder.
Changing programme positions
of the recorder using the
remote
5 Select “Command Mode,” and press
ENTER.
You can change programme positions of the
recorder using the number buttons.
Number
buttons
6 Select a Command Mode (DVD1,
DVD2, or DVD3), and press ENTER.
7 Set the Command Mode for the remote
so it matches the Command Mode for
the recorder you set above.
ENTER
Follow the steps below to set the
Command Mode on the remote.
1 Hold down ENTER.
2 While holding down ENTER, enter
the Command Mode code number
using the number buttons.
Example: for channel 50
Press “5,” “0,” then press ENTER.
Command Mode Code number
DVD1
DVD2
DVD3
number button 1
number button 2
number button 3
3 Hold down both the number and
ENTER buttons at the same time for
more than three seconds.
To check the Command Mode for the
recorder
Press x on the recorder when the recorder is
turned off. The Command Mode for the
recorder appears in the front panel display.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Easy Setup - Clock
The recorder will automatically search
for a clock signal. If a clock signal cannot
be found, set the clock manually using
</M/m/,, and press ENTER.
Step 6: Easy Setup
Make the basic adjustments by following the
on-screen instructions in “Easy Setup.”
Easy Setup - TV Type (page 87)
If you have a wide-screen TV, select
“16:9.” If you have a standard TV, select
either “4:3 Letter Box” (shrink to fit) or
“4:3 Pan Scan” (stretch to fit). This will
determine how “wide-screen” images are
displayed on your TV.
[/1
Easy Setup - Component Out
If you are using the COMPONENT
VIDEO OUT jack, select “On.”
</M/m/,,
ENTER
Easy Setup - Line3 Input
If you plan to connect a decoder such as
a PAY-TV/Canal Plus analogue decoder
to the LINE 3/DECODER jack, select
“Yes.”
O
RETURN
Easy Setup - Line1 Output
To output video signals, select “Video.”
To output S video signals, select “S
Video.”
TV [/1
To output RGB signals, select “RGB.”
Select “Video” to enjoy the
SMARTLINK features.
• If you set “Easy Setup - Component
Out” to “On,” you cannot select
“RGB.”
1 Turn on the recorder and your TV.
Then switch the input selector on your
TV so that the signal from the recorder
appears on your TV screen.
The initial settings message appears.
• If this message does not appear, select
“Easy Setup” from “SETUP” in the
System Menu (“Settings and
• If you set “Easy Setup - Line3 Input” to
“Yes,” you cannot select “S Video.”
Easy Setup - Audio Connection
If you connected an AV amplifier
(receiver) using a coaxial cord, select
“Yes : DIGITAL OUT” and set the
2 Press ENTER.
Follow the on-screen instructions to
make the following settings.
3 Press ENTER when “Finish” appears.
Easy Setup - OSD
Select a language for the on-screen
displays.
“Easy Setup” is finished.
To return to the previous step
Easy Setup - Tuner System
Select your country/region or language.
The programme position order will be set
according to the country/region you set.
To set the programme positions
• If you live in a French speaking country
that is not listed on the display, select
“ELSE - English.”
Press O RETURN.
z Hints
• If your AV amplifier (receiver) has an MPEG
audio decoder, set “MPEG” to “MPEG”
• If you want to run “Easy Setup” again, select
“Easy Setup” from “SETUP” in the System Menu
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a VCR or Similar Device
After disconnecting the recorder’s mains lead from the mains, connect a VCR or similar
recording device to the LINE IN jacks of this recorder.
Use the DV IN jack on the front panel if the equipment has a DV output jack (i.LINK jack)
For details, refer to the instruction manual supplied with the connected equipment.
To record on this recorder, see “Recording from connected equipment without a timer” on
Connecting to the LINE 3/DECODER jack
Connect a VCR or similar recording device to the LINE 3/DECODER jack of this recorder.
TV
VCR
SCART cord (not supplied)
to SCART input
to i LINE 3/DECODER
to i LINE 1 – TV
DVD recorder
b Notes
• Pictures containing copy protection signals that prohibit any copying cannot be recorded.
• If you pass the recorder signals through a VCR, you may not receive a clear image on your TV screen.
DVD recorder
VCR
TV
Be sure to connect your VCR to the DVD recorder and to your TV in the order shown below. To watch
video tapes, watch the tapes through a second line input on your TV.
Line input 1
VCR
TV
DVD recorder
Line input 2
• The SMARTLINK features are not available for devices connected via the DVD recorder’s LINE 3/
DECODER jack.
• When you record to a VCR from this DVD recorder, do not switch the input source to TV by pressing the
TV/DVD button on the remote.
• If you disconnect the recorder’s mains lead, you will not be able to view the signals from the connected
VCR.
,continued
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to the LINE 2 IN jacks on the front panel
Connect a VCR or similar recording device to the LINE 2 IN jacks of this recorder. If the
equipment has an S-video jack, you can use an S-video cord instead of an audio/video cord.
VCR, etc.
OUTPUT
VIDEO
AUDIO
S VIDEO
L
R
S-video cord
(not supplied)
Audio/video cord
(not supplied)
to LINE 2 IN
DVD recorder
: Signal flow
z Hint
When the connected equipment outputs only monaural sound, connect to just the L(MONO) and VIDEO
input jacks on the front of the recorder. Do not connect the R input jack.
b Notes
• Do not connect the yellow LINE IN (VIDEO) jack when using an S-video cord.
• Do not connect the output jack of this recorder to another equipment’s input jack with the other
equipment’s output jack connected to the input jack of this recorder. This may cause noise (feedback).
• Do not connect more than one type of video cord between the recorder and your TV at the same time.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Satellite or Digital Tuner
Connect a satellite or digital tuner to this recorder using the LINE 3/DECODER jack.
Disconnect the recorder’s mains lead from the mains when connecting the tuner.
To use the Synchro-Rec function, see below. Do NOT set “Line3 Input” of the “Scart Setting”
to “Decoder” in the “Video” setup when making this connection.
Satellite tuner,
CanalSat, etc.
TV
to SCART input
SCART cord (not supplied)
to i LINE 3/DECODER
to i LINE 1 – TV
DVD recorder
If the satellite tuner can output RGB
signals
If you want to use the Synchro Rec
function
This recorder accepts RGB signals. If the
satellite tuner can output RGB signals,
connect the TV SCART connector on the
satellite tuner to the LINE 3/DECODER jack,
and set “Line3 Input” of “Scart Setting” to
“Video/RGB” in the “Video” setup
(page 88). RGB signal images can be
displayed on the TV screen, but cannot be
recorded. Note that this connection and setup
disable the SMARTLINK function. If you
want to use the SMARTLINK function with
a compatible set top box, see the instructions
supplied with the set top box.
This connection is necessary to use the
Synchro-Recording function. See
Set “Line3 Input” of “Scart Setting” in the
specifications of your satellite tuner. See your
satellite tuner’s instructions for more
information.
If you are using a B Sky B tuner, be sure to
connect the tuner’s VCR SCART jack to the
LINE 3/DECODER jack. Then set “Line3
Input” of “Scart Setting” according to the
specifications of the VCR SCART jack on
your satellite tuner.
b Notes
• Synchro-Recording does not work with some
tuners. For details, see the tuner’s operating
instructions.
• If you disconnect the recorder’s mains lead, you
will not be able to view the signals from the
connected tuner.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a PAY-TV/Canal Plus Analogue Decoder
You can watch or record PAY-TV/Canal Plus analogue decoder programmes if you connect a
decoder (not supplied) to the recorder. Disconnect the recorder’s mains lead from the mains
when connecting the decoder. Note that when you set “Line3 Input” to “Decoder” in step 5 of
“Setting PAY-TV/Canal Plus analogue programme positions” (page 25), you will not be able
to select “L3” because Line 3 will become a dedicated line for the decoder.
Connecting a decoder
PAY-TV/Canal Plus
analogue decoder
TV
Aerial cable (supplied)
to AERIAL IN
to SCART input
SCART cord
(not supplied)
SCART cord
(not supplied)
to AERIAL OUT
to i LINE 1 – TV
to i LINE 3/DECODER
DVD recorder
24
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Select “Scart Setting,” and press
ENTER.
Setting PAY-TV/Canal Plus
analogue programme positions
To watch or record PAY-TV/Canal Plus
analogue programmes, set your recorder to
receive the programme positions using the
on-screen display.
In order to set the programme positions
correctly, be sure to follow all of the steps
below.
5 Press M/mto select “Video” or “RGB”
for “Line1 Output,” “Decoder” for
“Line3 Input,” and “Video” for “Line3
Output,” and press ENTER.
Number
buttons
The “Video” setup display appears again.
6 Press O RETURN to return the cursor
to the left column.
SYSTEM
MENU
7 Select “Basic,” and press ENTER.
</M/m/,,
ENTER
O
RETURN
1 Press SYSTEM MENU.
The System Menu appears.
8 Select “Channel Setting,” and press
ENTER.
2 Select “SETUP,” and press ENTER.
9 Press M/m to select the desired
programme position, and press
ENTER.
3 Select “Video,” and press ENTER.
,continued
25
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Select “System” using </,.
11 Press M/m to select an available TV
system, BG, DK, I, or L.
“L” is only available with French RDR-
HX520 and RDR-HX920 models. To
receive broadcasts in France, select “L.”
12 Select “Channel” using </,.
13 Select the PAY-TV/Canal Plus
analogue programme position using
M/m or number buttons.
14 Select “PAY-TV/ CANAL+” using </
,.
15 Select “On” using M/m, and press
ENTER.
To return to the previous step
Press O RETURN.
b Note
If you disconnect the recorder’s mains lead, you
will not be able to view the signals from the
connected decoder.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Eight Basic Operations
2. Recording a
Programme
— Getting to Know Your DVD Recorder
1. Inserting a Disc
+
RW
-
-
+
R
RWVR RWVideo
HDD
-
-
RVideo
RVR
+
+
R
-
-
-
RVR
RW
RWVR RWVideo
-
RVideo
This section introduces the basic operation to
record a current TV programme to the hard
disk (HDD) or to a disc (DVD). For an
explanation of how to make timer recordings,
DVD VCD CD
DATA DVD
DATA CD
Z (open/
close)
DVD
HDD
DVD
PROG +/–
TV/DVD
1 Press DVD.
DISPLAY
2 Press Z (open/close), and place a
disc on the disc tray.
z REC
REC MODE
x REC
STOP
TV t
Recording/playing side facing down
3 Press Z(open/close) to close the disc
tray.
1 Press HDD or DVD.
Wait until “LOAD” disappears from the
front panel display.
If you want to record to a DVD, insert a
recordable DVD.
Unused DVDs are formatted
automatically.
• For DVD-RW discs
DVD-RWs are formatted in the
recording format (VR mode or Video
mode) set by “Format DVD-RW” in
the “DVD” setup.
2 Press PROG +/– to select the
programme position or input source
you want to record.
3 Press REC MODE repeatedly to select
the recording mode.
Each time you press the button, the
display on the TV screen changes as
follows:
• For DVD-R discs
DVD-Rs are automatically formatted in
Video mode. To format an unused
DVD-R in VR mode, format the disc
using the “Disc Information” display
recording.
If the disc is recordable on this recorder,
you can manually re-format the disc to
For more details about the recording
,continued
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Note that the Teletext information will not
appear on your TV screen. To view the
Teletext information on your TV screen,
press TV/DVD on the remote to switch the
* not available in some areas
4 Press z REC.
Recording starts.
Recording stops automatically after 8
hours of continuous recording or when
the HDD or DVD is full.
b Notes
To stop recording
Press x REC STOP.
• After pressing z REC, it may take a short while
to start recording.
Note that it may take a few seconds for
recorder to stop recording.
• You cannot change the recording mode while
recording.
• If there is a power failure, the programme you are
recording may be erased.
• You cannot watch a PAY-TV/Canal Plus
programme while recording another PAY-TV/
Canal Plus programme.
• To use the TV Direct Rec function, you must first
correctly set the recorder’s clock.
To watch another TV programme while
recording
If your TV is connected to the i LINE 1 –
TV jack, set your TV to the TV input using
the TV/DVD button and select the
programme you want to watch. If your TV is
connected to the LINE 2 OUT or
COMPONENT VIDEO OUT jacks, set the
TV to TV input using the TV t button
Checking the disc status while
recording
You can check the recording information
such as recording time or disc type.
TV Direct Rec
If you are using the SMARTLINK
connection and the “TV Direct Rec” is set to
you are watching on your TV.
Press DISPLAY during recording.
The recording information appears.
When the TV and the recorder are turned on,
press z REC. The recorder starts recording
what you are watching on your TV.
b Note
If “TV” appears in the front panel display, you
cannot turn off the TV or change the programme
position during TV Direct Rec. To turn off the
function, set “TV Direct Rec” to “Off” in the
A Disc type/format
B Recording status
C Recording mode
D Recording time
About the Teletext function
Some broadcast systems ensure a Teletext
service* in which the complete programmes
and their data (title, date, programme
position, recording start time etc.) are stored
day by day. When recording a programme,
the recorder automatically takes the
programme name from the Teletext pages
and stores it as the title name. For details, see
Press DISPLAY to turn off the display.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Title List with Thumbnail Images
(Example: DVD+RW)
3. Playing the Recorded
Programme (Title List)
+
RW
-
-
+
R
RWVR RWVideo
HDD
-
-
RVideo
RVR
To play a recorded title, select the title from
the Title List.
m
HDD
DVD
Extended Title List
TITLE LIST
</M/m/,,
ENTER
OPTIONS
/
mc
CM
x
A Disc type:
Displays the media type, HDD or DVD.
Also displays the title type (Original or
Playlist) for HDD or DVD-RW/DVD-R
(VR mode) disc titles.
B Disc space (remainder/total)
1 Press HDD or DVD.
C Title information:
If you select DVD, insert a DVD (see “1.
Playback starts automatically depending
on the disc.
Displays the title number, title name, and
recording date. Title size is shown in the
Thumbnail title list.
z (red): Indicates that the title is
currently being recorded.
2 Press TITLE LIST.
: Indicates that the title is currently
being dubbed.
To show the extended Title List, press
OPTIONS to select “Display List,” and
press ENTER.
: Indicates the protected title.
“NEW”: Indicates that the title is newly
recorded (not played back) (HDD only).
: Indicates titles containing “Copy-
Once” copy protection signals (HDD
D Scroll bar:
Appears when all of the titles do not fit
on the list. To view the hidden titles,
press M/m.
E Title’s thumbnail picture:
The still images for each title are
displayed.
,continued
29
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Select a title, and press ENTER.
The sub-menu appears.
To change the title order (Sort)
While the Title List menu is turned on, press
OPTIONS to select “Sort Titles.” Press M/m
to select the item, and press ENTER.
The sub-menu displays options
applicable only to the selected item. The
displayed options differ depending upon
the model, situation, and disc type.
Order
Sorted
By Date
In order of when the titles
were recorded. The title that is
recorded most recently is
listed at the top.
By Title
In alphabetical order.
By Number
In order of recorded title
number.
Unseen Title
(HDD only)
In order of when the titles
were recorded. The title that is
recorded most recently and
has not been played is listed at
the top. Playlist titles are not
displayed.
Sub-menu
4 Select “Play,” and press ENTER.
Playback starts from the selected title.
To change a title thumbnail picture
(Thumbnail) (HDD/DVD-RW/DVD-R in VR
mode only)
To stop playback
Press x (stop).
You can select a favourite scene for the
thumbnail picture shown in the Title List
menu.
To scroll the list display by page (Page
mode)
Press
/
while the list display is turned
, the entire
on. Each time you press
/
1
Press TITLE LIST.
Press </, to switch the Title Lists, if
necessary.
Title List changes to the next/previous page
of titles.
2
3
Select a title, and press ENTER.
The sub-menu appears.
About the Title List for HDD/DVD-RWs/
DVD-Rs (VR mode)
You can switch the Title List to show
Original or Playlist titles.
While the Title List menu is turned on, press
</,.
Select “Set Thumbnail,” and press
ENTER.
The display for setting the thumbnail
point appears and the title starts to play.
4
5
While watching the playback picture,
press m/M to select the scene you
want to set for a thumbnail picture, and
press ENTER.
Playback pauses.
Press ENTER if the scene is correct.
If the scene is incorrect, press c/C to
select the scene you want to set for a
thumbnail picture, and press ENTER.
The display asks for confirmation.
• To change the thumbnail, press M.
6
Select “OK,” and press ENTER.
The scene is set for the title’s thumbnail
picture.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
To turn off the Title List
Press TITLE LIST.
4. Displaying the
Playing/Remaining Time
and Play Information
z Hints
• After recording, the first scene of the recording
(the title) is automatically set as the thumbnail
picture.
• You can select “TITLE LIST” from the System
Menu.
+
RW
+
R
-
-
HDD
RWVR RWVideo
-
-
RVideo
RVR
DVD VCD
CD
b Notes
DATA DVD DATA CD
• The title names may not appear for DVDs created
on other DVD recorders.
You can check the playing time and
remaining time of the current title, chapter,
track, or disc. Also, you can check the disc
name recorded on the DVD/CD.
• It may take a few seconds for the thumbnail
pictures to be displayed.
• After editing, the title thumbnail picture may
change to the first scene of the recording (title).
• After dubbing, the title thumbnail picture set on
the source recording is cancelled.
DISPLAY
ENTER
OPTIONS
TIME/TEXT
Press DISPLAY.
The displays differ depending on the disc
type or playing status.
A Title number/name
(Shows either track number, track
name, scene number, or file name for
CDs, VIDEO CDs, DATA DVDs, or
DATA CDs.)
,continued
31
Download from Www.Somanuals.com. All Manuals Search And Download.
z Hints
B Available functions for DVD VIDEOs
angle/ audio/ subtitle,
• If “DTS” of “Audio Connection” is set to “Off” in
the “Audio” setup, the DTS track selection option
will not appear on the screen even if the disc
(
etc.), or playback data for DATA
DVDs and DATA CDs
• When “Auto Display” is set to “On” (default) in
automatically appears on the screen when the
recorder is operated.
C The current selected function or audio
setting (appears only temporarily)
Example: Dolby Digital 5.1 ch
Rear (L/R)
b Note
Playing time of MP3 audio tracks may not be
displayed correctly.
Checking the playing/
remaining time
Front (L/R) +
Centre
LFE (Low Frequency
Effect)
You can view the playing or time information
displayed on the front panel display.
D The current selected angle
*1
Press TIME/TEXT repeatedly.
The displays differ depending on the disc
type or playing status.
F Title type (only appears for Playlists)
G Play mode
Example: When playing a DVD
Playing time and number of the
current title
*2
I Playing status bar
*3
J Title number (chapter number )
(Shows either track number, scene
number, album number , or file
*3
Remaining time of the current title
number for CDs, VIDEO CDs, DATA
DVDs, or DATA CDs.)
K Album name appears for DATA DVDs
or DATA CDs.
Playing time and number of the
current chapter
For CDs with CD text, press TIME/
TEXT.
*3
L Playing time (remaining time )
Remaining time of the current chapter
*1
Displays Super VIDEO CDs as “SVCD,” DATA
CDs as “CD” and DATA DVDs as “DVD.”
Does not appear with VIDEO CDs, DATA
*2
DVDs, and DATA CDs.
Displayed when you press TIME/TEXT
*3
Example: When playing a VIDEO CD
repeatedly.
Playing time and number of the current
scene or track
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Example: When playing a CD
Track playing time and the current track/index
number
Checking the remaining disc
space
m
Remaining time of the current track
You can check the remaining disc space
using the “Disc Information” display.
m
Playing time of the disc
m
1 Insert a disc.
Remaining time of the disc
m
CD text (when available)
2 Press OPTIONS to select “Disc
Information,” and press ENTER.
The “Disc Information” display appears.
Available settings differ depending on
the disc type.
Example: When playing an MP3 audio track
Playing time and number of the current track
m
Current album number
Example: When a DVD+RW is inserted.
Example: When viewing a JPEG image
Current file number and total number of files in the
current album
m
Current album number and total number of
albums
b Notes
• The recorder can only display the first level of a
CD’s text, such as the disc name.
• Playing time of MP3 audio tracks may not be
displayed correctly.
“Remainder” (approximate)
• The remaining recording time in each
of the recording modes
• Disc space bar
• Remaining disc space/total disc space
z Hint
To increase disc space, see “To open up disc space”
33
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Press </M/m/, to select the
character you want to enter, and press
ENTER.
5. Changing the Name of
a Recorded Programme
The selected character appears at the top
of the display.
Example: Input Title Name
+
-
-
+
R
RWVR RWVideo
HDD
RW
-
-
RVideo
RVR
You can label a DVD, title, or programme by
entering characters. You can enter up to 64
characters for a title or disc name, but the
actual number of characters displayed in the
menus such as the Title List will vary. The
steps below explain how to change the name
of the recorded programme.
The type of characters will change
according to the language you select in
“Easy Setup.” Some languages allow you
to enter an accent mark.
To enter a letter with an accent mark,
select an accent followed by the letter.
Example: Select “ ` ” and then “a” to
enter “à.”
Number
buttons
INPUT
SELECT
To insert a space, select “Space.”
TITLE LIST
6 Repeat steps 4 and 5 to enter the
remaining characters.
Input row
</M/m/,,
ENTER
1 Press TITLE LIST.
2 Select a title, and press ENTER.
The sub-menu appears.
To erase a character, move the cursor to
the right of the character at the input row.
Select “Back” and press ENTER.
To insert a character, move the cursor to
the right of the point where you want to
insert the character. Select the character
and press ENTER.
3 Select “Title Name,” and press
ENTER.
The display for entering characters
appears.
4 Press </M/m/, to move the cursor
to the right of the display and select
“A” (upper-case), “a” (lower-case),
or “Symbol,” and press ENTER.
The characters for the selected type are
displayed.
To erase all of the characters, select
“Clear All” and press ENTER.
7 Select “Finish,” and press ENTER.
To cancel the setting, select “Cancel.”
34
Download from Www.Somanuals.com. All Manuals Search And Download.
To use the number buttons
You can also use the number buttons to enter
characters. Refer to the number next to each
row of letters on your TV screen.
6. Labelling and
Protecting a Disc
1
In step 5 above, press a number button
repeatedly to select a character.
Example:
You can execute options effective for the
entire disc using the “Disc Information”
display.
Press the number 3 button once to enter
“D.”
Press the number 3 button three times to
enter “F.”
2
3
Press ENTER and select the next
character.
Select “Finish” and press ENTER.
z Hint
You can switch between “A” (upper-case), “a”
(lower-case), or “Symbol” by pressing INPUT
SELECT.
</M/m/,,
ENTER
OPTIONS
Labelling a disc
+
RW
-
-
+
-
RVR
RWVR RWVideo
R
-
RVideo
1 Insert a disc.
2 Press OPTIONS to select “Disc
Information,” and press ENTER.
The “Disc Information” display appears.
Available settings differ depending on
the disc type.
Example: When the inserted disc is a
DVD+RW.
3 Select “Disc Name,” and press
ENTER.
Enter the disc name in the “Input Disc
,continued
35
Download from Www.Somanuals.com. All Manuals Search And Download.
b Note
You can enter up to 64 characters for a DVD’s disc
name. The disc name may not appear when the disc
is played on other DVD equipment.
7. Playing the Disc on
Other DVD Equipment
(Finalise)
Protecting a disc
+
-
-
+
R
RWVR RWVideo
-
RVR
RW
-
-
RVR
RWVR
-
RVideo
1 Insert a disc.
Finalising is necessary when you play discs
recorded with this recorder on other DVD
equipment.
When you finalise a DVD+RW, DVD-RW
(Video mode), DVD+R, or DVD-R (Video
mode), a DVD menu will be automatically
created, which can be displayed on other
DVD equipment.
2 Press OPTIONS to select “Disc
Information,” and press ENTER.
The “Disc Information” display appears.
Available settings differ depending on
the disc type.
Example: When the inserted disc is a
DVD-RW (VR mode).
Before finalising, check the differences
between the disc types in the table below.
Differences between the disc types
Discs are automatically finalised
+
RW
when removed from the recorder.
However, you may need to finalise
the disc for certain DVD
equipment, or if the recording time
is short. You can edit or record on
the disc even after finalising.
Finalising is unnecessary when
playing a disc on VR format
compatible equipment.
Even if your other DVD equipment
is VR format compatible, you may
need to finalise the disc, especially
if the recording time is short. You
can edit or record on the disc even
after finalising.
A
“On”/“Off”: Indicates whether
protection is set (DVD-RW/DVD-
R in VR mode only)
-
RWVR
B “Protect Disc”
3 Select “Protect Disc,” and press
ENTER.
4 Select “Protect,” and press ENTER.
Finalising is necessary when
playing on any equipment other
than this recorder.
After finalising, you cannot edit or
record on the disc. If you want to
record on it again, unfinalise
(page 38) or reformat the disc
(page 38). However, if you
reformat the disc, all recorded
contents will be erased.
-
RWVideo
To cancel the protection
Select “Unprotected” in step 4.
z Hint
You can set protection for individual titles
Finalising is necessary. The disc
can be played only on equipment
that supports DVD-R in VR mode.
After finalising you cannot edit or
record on the disc using this
recorder.
-
RVR
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Finalising is necessary when
playing on any equipment other
than this recorder.
After finalising, you cannot edit or
record on the disc.
+
R
Finalising the disc using “Disc
Information” display
-
RVideo
1 Insert a disc.
2 Press OPTIONS to select “Disc
Information,” and press ENTER.
The “Disc Information” display appears.
Z (open/
close)
3 Select “Finalise,” and press ENTER.
The display shows the approximate time
required for finalising and asks for
confirmation.
(Example: DVD+RW)
</M/m/,,
ENTER
OPTIONS
Finalising the disc using Z
(open/close) button
4 Select “OK,” and press ENTER.
The recorder starts finalising the disc.
1 Make a recording.
z Hint
You can check whether the disc has been finalised
or not. If you cannot select “Finalise” in step 3
above, the disc has already been finalised.
2 Press Z (open/close).
The display shows the approximate time
required for finalising and asks for
confirmation.
b Notes
For DVD+RWs, the recorder
automatically starts finalising the disc.
After finalising, the disc will be ejected
automatically.
• Depending on the condition of the disc,
recording, or the DVD equipment, discs may not
play even if the discs are finalised.
• The recorder may not be able to finalise the disc
if it was recorded on another recorder.
3 Select “OK,” and press ENTER.
The recorder starts finalising the disc.
After finalising, the disc will be ejected
automatically.
,continued
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Unfinalising a disc
8. Reformatting a disc
-
-
RWVR RWVideo
+
RW
-
-
RWVR RWVideo
For DVD-RWs (Video mode)
DVD-RWs (Video mode) that have been
finalised to prohibit additional recording or
editing can be unfinalised to allow further
recording or editing.
New discs are automatically formatted when
inserted. If necessary, you can manually re-
format a DVD+RW or DVD-RW disc to
make a blank disc. For DVD-RWs, you can
select a recording format (VR mode or Video
For DVD-RWs (VR mode)
If you cannot record or edit on a DVD-RW
(VR mode) that has been finalised with other
DVD equipment, unfinalise the disc.
b Note
The recorder is not able to unfinalise DVD-RWs
(Video mode) that have been finalised on another
recorder.
1 Insert a disc.
</M/m/,,
ENTER
2 Press OPTIONS to select “Disc
Information,” and press ENTER.
The “Disc Information” display appears.
OPTIONS
3 Select “Unfinalise,” and press
ENTER.
1 Insert a disc.
The recorder starts unfinalising the disc.
Unfinalising may take several minutes.
2 Press OPTIONS to select “Disc
Information,” and press ENTER.
Example: When a DVD+RW is inserted.
3 Select “Format,” and press ENTER.
4 Select “OK,” and press ENTER.
For DVD-RWs and unrecorded DVD-Rs
(Video mode), select “VR” or “Video,”
and press ENTER.
All contents on the disc are erased.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
z Hint
By reformatting, you can change the recording
format on DVD-RWs, or record again on DVD-
RWs that have been finalised.
b Note
On this model, 1 GB (read “gigabyte”) is equivalent
to 1 billion bytes. The larger the number, the larger
the disc space.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Press REC MODE repeatedly to switch the
recording modes.
Timer Recording
To select the HQ+ mode, set “HQ Setting” of
the “HDD Rec. Settings” to “HQ+” in the
pictures in higher quality than HQ on the
HDD. Note that HQ+ plus appears as HQ in
the front panel display and the on-screen
displays.
Before Recording
Before you start recording…
• Check that the disc has enough available
HDD, DVD+RWs, and DVD-RWs, you
can free up disc space by erasing titles
Approx. recording time
(hours)
Recording
mode
HDD
DVD*
• Adjust the recording picture quality and
RDR- RDR- RDR-
HX520 HX720/ HX920
HX722
z Hint
HQ+(High 8
quality)
20
33
–
Timer recordings will be made regardless whether
or not the recorder is turned on. You can turn off the
recorder without affecting the recording even after
recording starts.
HQ
R
13
19
32
46
53
77
1
HSP R
1 hr.
30 min.
b Note
To play a recorded disc on other DVD equipment,
SP
(Standard
mode)
26
33
61
77
102
127
2
LSP
r
2 hr.
30 min.
Recording mode
Like the standard ×3 recording modes of
video tapes, you can select the desired
recording mode using the REC MODE
button.
Recording modes with higher quality provide
a more beautiful recording, but the large data
volume also results in a shorter recording
time.
ESP
LP
r
r
r
39
53
79
93
153
205
308
410
3
4
6
8
124
187
249
EP
SLP (Long 106
duration)
* The recording time for DVD+R DL (Double
Layer) discs is as follows:
HQ: 1 hour 48 minutes
HSP: 2 hours 42 minutes
SP: 3 hours 37 minutes
Conversely, a longer duration provides a
longer recording time, but the lower data
volume results in a coarser picture quality.
LSP: 4 hours 31 minutes
ESP: 5 hours 25 minutes
LP: 7 hours 14 minutes
EP: 10 hours 51 minutes
SLP: 14 hours 28 minutes
b Notes
• The maximum continuous recording time for a
single title is eight hours.
• Situations below may cause slight inaccuracies
with the recording time.
– Recording a programme with poor reception, or
a programme or video source of low picture
quality
– Recording on a disc that has already been edited
– Recording only a still picture or just sound
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording stereo and bilingual
programmes
Unrecordable pictures
Pictures with copy protection cannot be
recorded on this recorder.
When the recorder receives a copy guard
signal, the recorder continues to record but
only a blank, grey coloured screen will be
recorded.
The recorder automatically receives and
records stereo and bilingual programmes
based on the ZWEITON system or the
NICAM system.
The HDD and a DVD-RW (VR mode) or
DVD-R (VR mode) can record both main and
sub sounds. You can switch between main
and sub when playing the disc. For the HDD,
you can select the sound track before
recording. Select “Main,” “Sub,” or
“Main+Sub” in “Bilingual Recording” of the
“HDD Rec. Settings” in the “Recording”
A DVD+RW, DVD-RW (Video mode),
DVD+R, or DVD-R (Video mode) can
record only one sound track (main or sub) at
a time. Select the sound track using the Setup
Display before recording starts. Set
“Bilingual Recording” of the “DVD Rec.
Settings” to “Main” (default) or “Sub” in the
Copy control Recordable discs
signals
Copy-Free
+
RW
-
RWVR
HDD
-
+
R
-
RVR
RWVideo
-
RVideo
Copy-Once
Copy-Never
HDD
-
RWVR
(CPRM*)
(CPRM*)
-
RVR
None (a blank screen is
recorded)
* The recorded disc can be played only on CPRM
compatible equipment (page 8).
ZWEITON (German stereo) system
When a stereo based programme is received,
“Stereo” appears.
When a bilingual ZWEITON based
programme is received, “Main,” “Sub,” or
“Main/Sub” appears.
NICAM system
When a stereo or bilingual NICAM based
programme is received, “NICAM” appears in
the front panel display.
To record a NICAM programme, be sure to
set “Audio” of “Channel Setting” in the
“Basic” setup to “NICAM” (default). If the
sound is not clear when listening to NICAM
broadcasts, set “Audio” to “Standard” (see
z Hint
You can select the audio (main or sub) while
recording bilingual programmes using the AUDIO
button. This does not affect the recorded sound.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Press TIMER.
Timer Recording
(Standard/VIDEO Plus+)
+
-
-
+
R
RWVR RWVideo
HDD
RW
-
-
RVideo
RVR
You can set the timer for a total of 40
programmes (8 programmes when using the
PDC/VPS function), up to 30 days in
advance.
There are two methods to set the timer: the
standard method and VIDEO Plus+ (RDR-
HX520/HX720 only) method.
• Standard: Set the date, time, and
programme position of the programme
manually.
2 Press M/m to select the “Day and
Time” or “Mode” row. Then press
ENTER.
3 Select an item using </, and
adjust using M/m. Then press ENTER.
To make additional changes to items in
different rows, return to step 2. The
adjustable items are listed below.
“Day and Time”:
• VIDEO Plus+ (RDR-HX520/HX720 only):
Enter the PlusCode programming number
designated for each TV programme
Sets the date, start time, and stop time,
and selects the programme position or
input source.
The date item changes as follows:
Today y …… y Sat 28.10 (30 days
later) y Sun (every Sunday) y ……
y Sat (every Saturday) y Mon - Fri
(Monday to Friday) y Mon - Sat
(Monday to Saturday) y Daily y
Today
Setting the timer manually
(Standard)
“Mode”:
“Media”:
Selects the media, HDD or DVD.
“PDC/VPS”:
Sets the PDC/VPS function. See “About
the PDC/VPS function” below.
“Extend Time”:
Sets the duration in increments of 10
minutes, for a maximum of 60 minutes
when a timer recording is in progress. If
the programme set to be recorded daily or
weekly is extended, the manually
extended time set here will be added to
the subsequent timer recording times.
Note that when “PDC/VPS” is set to
“On,” you cannot make the “Extend
Time” setting.
TIMER
</M/m/,,
ENTER
OPTIONS
x REC
STOP
• If you make a mistake, select the item
and change the setting.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Select “OK,” and press ENTER.
The “TIMER LIST” display (page 47)
appears. The TIMER REC indicator
lights up on the front panel and the
recorder is ready to start recording.
Unlike a VCR, there is no need to turn off
the recorder before the timer recording
starts.
Auto Title Erase (HDD only)
If there is not enough space for a timer
recording, the recorder automatically erases
old titles recorded on the HDD. The oldest,
played title is erased. Set “Auto Title Erase”
of the “Timer Settings” to “On” in the
are not erased.
If the timer settings overlap
Overlapped timer settings are shown as
follows.
To stop recording during timer recording
Press x REC STOP.
Note that it may take a few seconds for the
recorder to stop recording.
About the PDC/VPS function
PDC/VPS signals are transmitted with TV
programmes in some broadcast systems.
These signals ensure that timer recordings are
made regardless of any broadcast delays,
early starts, or broadcast interruptions.
To store the setting as shown, select “OK.”
The programme that does not have a
mark next to it has priority and the
overlapped programmes start recording only
after the first programme has finished.
To cancel the overlapped setting, select
“Cancel.”
To use the PDC/VPS function
Set “PDC/VPS” to “On” in step 3 above.
When you turn on this function, the recorder
starts scanning the channels before the timer
recording starts. If you are watching TV
when scanning starts, a message will appear
on the TV screen. If you want to watch TV,
switch to your TV’s tuner or turn off the
PDC/VPS channel scan function.
To confirm, change, or cancel a timer
recording
Note that if you turn off the PDC/VPS
channel scan function, the timer recording
will not start.
To extend the recording duration time
while recording
To temporarily turn off PDC/VPS channel
scan
Press OPTIONS and select “PDC/VPS Scan
Off.”
1
Press OPTIONS during recording to
select “Extend Rec,” and press ENTER.
To ensure that the PDC/VPS function works
properly, turn off the recorder before the
timer recording starts. This will
automatically turn on the PDC/VPS channel
scan function while the recorder remains off.
Rec Mode Adjust
If there is not enough available disc space for
the recording, the recorder automatically
adjusts the recording mode to enable the
entire programme to be recorded. Set “Rec
Mode Adjust” of the “Timer Settings” to
2
3
Press M/m to select the duration time.
You can set the duration in increments of
10 minutes, for a maximum of 60
minutes.
Select “OK” and press ENTER.
,continued
43
Download from Www.Somanuals.com. All Manuals Search And Download.
One Touch Timer
Recording TV programmes
using the VIDEO Plus+ system
(RDR-HX520/HX720 only)
If you use the SMARTLINK connection, you
can easily display the timer programming
menu.
When the TV is turned on or in standby
mode, press TIMER. The recorder
automatically turns on and the TV’s input is
switched to the recorder. The Timer
programming menu appears.
The VIDEO Plus+ system is a feature that
simplifies setting the timer. Just enter the
PlusCode programming number listed in the
TV programme guide. The date, time, and
programme position of that programme are
set automatically.
Check that the programme positions are
correctly set in “Channel Setting” in the
z Hint
If you are recording to the HDD or a DVD-RW (VR
mode) at a recording mode that is SP or lower and
is a 2x speed or higher disc, you can play the title as
it is being recorded by selecting the programme title
b Notes
• If a message indicating that the disc is full appears
on the screen, change the disc, or make available
space for the recording (HDD/DVD+RW/DVD-
Number
buttons
• Check that the clock is correctly set before setting
the timer recording. If not, the timer recording
cannot be made.
TIMER
• To record a satellite programme, turn on the
satellite tuner and select the satellite programme
you want to record. Leave the satellite tuner
turned on until the recorder finishes recording. If
you connect equipment with a timer function, you
• Even if the timer is set for the same daily or
weekly programme, the timer recording cannot be
made if it overlaps with a programme that has
</M/m/,,
ENTER
z REC
x REC
STOP
priority. “
” will appear next to the overlapped
setting in the Timer List. Check the priority order
of the settings.
• Even if the timer is set, timer recordings cannot be
made while recording a programme that has
priority.
1 Press TIMER.
• The Rec Mode Adjust function only works with a
timer recording and the PDC/VPS function set to
off. It does not function with Quick Timer or
Synchro Rec. In addition, the Rec Mode Adjust
function does not work when recording to the
HDD while “Auto Title Erase” of the “Timer
Settings” is set to “On” in the “Recording” setup.
• The beginning of some recordings may not be
made when using the PDC/VPS function.
• You cannot extend the recording duration time
when “PDC/VPS” is set to “On.”
2 Select “PlusCode No.” using M/m,
and press ENTER.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Press the number buttons to enter the
PlusCode programming number, and
press ENTER.
Using the Quick Timer function
You can set the recorder to record in 30
minute increments.
The date, start and stop times,
programme position, recording mode,
etc. setting (page 43) appear.
• If you make a mistake before pressing
ENTER, press </, and re-enter the
correct number.
Press z REC repeatedly to set the
duration.
Each press advances the time in 30 minute
increments. The maximum duration is six
hours.
(normal recording)
The time counter decreases minute by minute
to 0:00, then the recorder stops recording (the
power does not turn off). Even if you turn off
the recorder during recording, the recorder
continues to record until the time counter
runs out.
Note that the Quick Timer function does not
work if “TV Direct Rec” is set to “On” in the
• If you want to change the setting, press
</, to select the item and press M/m
to change the setting.
• If you want to re-enter the PlusCode
programming number, select
“PlusCode No.,” and press ENTER.
Then re-enter the PlusCode
programming number.
To cancel the Quick Timer
4 Select “OK,” and press ENTER.
The TIMER REC indicator lights up on
the front panel, and the recorder is ready
to start recording.
Press z REC repeatedly until the counter
appears in the front panel display. The
recorder returns to normal recording mode.
To stop recording during timer recording
Press x REC STOP.
Note that it may take a few seconds for the
recorder to stop recording.
If the timer settings overlap
See page 43.
To extend the recording duration time
while recording
See page 43.
To confirm, change, or cancel a timer
recording
z Hint
The Rec Mode Adjust function also works with this
timer method (page 43).
,continued
45
Download from Www.Somanuals.com. All Manuals Search And Download.
“HDD Rec. Picture Size”/“DVD Rec.
Picture Size”:
Sets the picture size of the programme to
be recorded.
Adjusting the recording picture
quality and size
• 4:3 (default): Sets the picture size to
4:3.
• 16:9: Sets the picture size to 16:9 (wide
mode).
You can adjust the recording picture quality
and picture size.
• Auto (HDD only): Automatically
selects the actual picture size.
“DVD Rec. Picture Size” works with
DVD-RWs/DVD-Rs (Video mode)
when the recording mode is set to HQ,
HSP, SP, LSP, or ESP. For all other
recording modes, the screen size is fixed
at “4:3.”
For DVD-Rs/DVD-RWs (VR mode), the
actual picture size is recorded regardless
of the setting. For example, if a 16:9 size
picture is received, the disc records the
picture as 16:9 even if “DVD Rec.
Picture Size” is set to “4:3.”
For DVD+RWs/DVD+Rs, the screen
size is fixed at “4:3.”
</M/m/,,
ENTER
OPTIONS
1 Before recording starts, press
OPTIONS to select “Rec Settings,”
and press ENTER.
“Rec NR” (noise reduction): Reduces
noise contained in the video signal.
“Rec Video Equalizer”: Adjusts the
picture in greater detail.
Press M/m to select the item you want to
adjust, then press ENTER.
• Contrast: Changes the contrast.
• Brightness: Changes the overall
brightness.
• Colour: Makes the colours deeper or
lighter.
2 Select the item you want to adjust,
and press ENTER.
3 Adjust the setting using </M/m/,,
and press ENTER.
The adjustment display appears.
The default setting is underlined.
“Rec NR”: (weak) Off 1 ~ 2 ~ 3
(strong)
Example: Rec NR
“Rec Video Equalizer”:
• Contrast: (weak) –3 ~ 0 ~ 3 (strong)
• Brightness: (dark) –3 ~ 0 ~ 3 (bright)
• Colour: (light) –3 ~ 0 ~ 3 (deep)
Repeat steps 2 and 3 to adjust any other
items.
“Rec Mode”:
Selects the recording mode for the
desired recording time and picture
quality. For more information, see
46
Download from Www.Somanuals.com. All Manuals Search And Download.
b Notes
• If one programme contains two picture sizes, the
selected size is recorded. However, if the 16:9
signal cannot be recorded as 16:9, it is recorded as
4:3.
• When playing a 16:9 size picture recorded as 4:3,
the image is fixed to 4:3 Letter Box regardless of
the setting in “TV Type” of “Video” setup
Checking/Changing/
Cancelling Timer
Settings (Timer List)
+
RW
-
-
+
R
RWVR RWVideo
HDD
-
-
RVideo
RVR
• Remnants of images may appear on your screen
when using “Rec NR.”
You can check, change, or cancel timer
settings using the Timer List.
• “Rec Video Equalizer” does not affect the input
of the DV IN jack and does not work with RGB
signals.
Creating chapters in a title
The recorder can automatically divide a
recording (a title) into chapters by inserting
chapter marks at approximately 6 minute
intervals during recording. To disable this
function, set “Auto Chapter” in the
When recording to the HDD, a DVD-R (VR
mode) or a DVD-RW (VR mode), you can
insert and erase chapter marks manually
TIMER LIST
</M/m/,,
ENTER
O
RETURN
/
b Note
dubbing source are not retained in the dubbed title.
1 Press TIMER LIST.
The Timer List appears.
Timer information displays the recording
date, time, recording mode, etc.
:
Indicates that the setting is overlapped by
another setting.
(red):
z
Indicates the setting is currently being
recorded.
:
Indicates that the timer recording cannot
be recorded as set, such as for a timer
recording that cannot be recorded in the
selected Rec mode.
,continued
47
Download from Www.Somanuals.com. All Manuals Search And Download.
:
“Check Overlap”:
Indicates the setting is being recorded to
the HDD.
Checks for overlapped settings.
The timer setting without the
mark
:
has priority over the other settings.
Indicates the setting is being recorded to
a DVD.
When all of the timer settings do not fit
on the list, the scroll bar appears.
To view the hidden timer settings, press
M/m.
2 Select the timer setting you want to
check/change/cancel, and press
ENTER.
Select “Close” to return to the Timer List.
To change or cancel the setting, repeat
steps 2 and 3 above.
The sub-menu appears.
3 Select one of the options, and press
When the timer settings overlap
ENTER.
The programme that starts first has priority
and the second programme starts recording
only after the first programme has finished.
“Modify”:
Changes the timer setting.
Select an item using </, and adjust
using M/m. Select “OK,” and press
ENTER.
will be cut off
When the recordings start at the same
time
The programme that is set last has priority. In
this example, timer setting B is set after A, so
the first part of timer setting A will not be
recorded.
“Erase”:
Erases the timer setting. Select “OK,”
and press ENTER.
When the end time of one recording and
the start time of another are the same
After finishing the previous recording, the
other recording may be delayed.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
To scroll the list display by page (Page
mode)
Recording From
Press
/
while the list display is turned
, the entire
Connected Equipment
on. Each time you press
/
Timer List changes to the next/previous page
of timer settings.
+
RW
-
-
+
R
RWVR RWVideo
HDD
-
-
RVideo
RVR
To turn off the Timer List
Press TIMER LIST or O RETURN.
z Hint
HDD
DVD
While recording, you cannot modify the timer
setting for the current recording, but you can extend
the duration of the recording time (page 43).
INPUT
SELECT
b Notes
• When “PDC/VPS” is set to “On” for one or more
timer recordings, the start times may change in
the event of a broadcast delay or early start.
• Even if the timer is set, timer recordings cannot be
made while recording a programme that has
priority.
</M/m/,,
ENTER
OPTIONS
• Even if the timer is set for the same daily or
weekly programme, the timer recording cannot be
made if it overlaps with a programme that has
priority. “
” will appear next to the overlapped
z REC
x REC
STOP
REC MODE
setting in the Timer List. Check the priority order
of the settings.
c z
SYNCHRO
REC
Recording from connected
equipment with a timer
(Synchro Rec)
You can set the recorder to automatically
record programmes from connected
equipment that has a timer function (such as
a satellite tuner). Connect the equipment to
the LINE 3/DECODER jack of the recorder
When the connected equipment turns on, the
recorder starts recording a programme from
the LINE 3/DECODER jack.
1 Before recording, select HDD or DVD.
If you select DVD, insert a recordable
page 27).
2 Set “Synchro Rec” to “Record to
HDD” or “Record to DVD” in the
,continued
49
Download from Www.Somanuals.com. All Manuals Search And Download.
b Notes
3 Press INPUT SELECT repeatedly to
select “L3.”
• The recorder starts recording only after detecting
a video signal from the connected equipment. The
beginning of the programme may not be recorded
regardless of whether or not the recorder’s power
is on or off.
4 Select the desired audio signal when
recording a bilingual programme to
the HDD or DVD-RWs/DVD-Rs (VR
mode).
• During Synchro-Recording, other operations,
such as normal recording, cannot be performed.
• To use the connected equipment while the
recorder is standing by for Synchro-Recording,
cancel Synchro-Recording by pressing c z
SYNCHRO REC. Be sure to turn off the
connected equipment and press c z SYNCHRO
REC to reset Synchro-Recording before the timer
recording starts.
• The Synchro Rec function does not work when
“Line3 Input” of “Scart Setting” is set to
• The Synchro Rec function does not work with
some tuners. For details, see the tuner’s operating
instructions.
Press OPTIONS to select “Line Audio
Input,” and press ENTER. Then select
“Bilingual,” and press ENTER.
For details about bilingual recording, see
5 Press REC MODE repeatedly to select
the recording mode.
For details about the recording mode, see
6 Set the timer on the connected
equipment to the time of the
programme you want to record, and
turn it off.
• While the recorder is standing by for Synchro-
Recording, the Auto Clock Set function (page 86)
does not work.
• To use the Synchro Rec function, you must first
set the recorder’s clock correctly.
7 Press c z SYNCHRO REC.
The SYNCHRO REC indicator lights up
on the front panel. The recorder is ready
to start Synchro-Recording.
If the timer settings of a Synchro-
Recording and another timer recording
overlap
Regardless of whether or not the programme
is a Synchro Rec programme, the programme
that starts first has priority and the second
programme starts recording only after the
first programme has finished.
The recorder automatically starts
recording when it receives an input
signal from the connected equipment.
The recorder stops recording when the
connected equipment turns off.
To stop recording
Press x REC STOP or c z SYNCHRO
REC.
First
programme
Second
programme
To cancel Synchro Rec
Press c z SYNCHRO REC.
The SYNCHRO REC indicator on the
recorder turns off.
will be cut off
50
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Press the pause (or play) button on the
connected equipment to cancel the
playback pause status.
Recording from connected
equipment without a timer
The connected equipment starts playback
and the playback image is recorded by
this recorder.
To stop recording, press x REC STOP
on this recorder.
You can record from a connected VCR or
similar device. To connect a VCR or similar
device, see “Connecting a VCR or Similar
Device” on page 21. Use the DV IN jack on
the front panel if the equipment has a DV
output jack (i.LINK jack).
If you connect a digital video camera with
a DV IN jack
See “DV Dubbing” on page 76 for an
explanation of how to record from the DV IN
jack.
1 Press HDD or DVD.
If you select DVD, insert a recordable
2 Press INPUT SELECT to select an input
source according to the connection
you made.
z Hint
You can adjust the settings for the recording picture
before recording. See “Adjusting the recording
The front panel display changes as
follows:
b Notes
programme
position
• When recording a video game image, the screen
may not be clear.
• Any programme that contains a Copy-Never copy
guard signal cannot be recorded. The recorder
continues to record, but a blank screen will be
recorded.
3 Select the desired audio signal when
recording a bilingual programme to
the HDD or DVD-RWs/DVD-Rs (VR
mode).
Press OPTIONS to select “Line Audio
Input,” and press ENTER. Then select
“Bilingual,” and press ENTER.
For details about bilingual recording, see
4 Press REC MODE repeatedly to select
the recording mode.
For details about the recording mode, see
5 Insert the source tape into the
connected equipment and set to
playback pause.
6 Press z REC.
This recorder starts recording.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Select the title, and press ENTER.
The sub-menu appears.
Playback
Playing
+
4 Select “Play,” and press ENTER.
Playback starts from the selected title.
To use the DVD’s Menu
+
R
-
-
HDD
RW
RWVR RWVideo
When you play a DVD VIDEO, or a finalised
DVD+RW, DVD-RW (Video mode),
DVD+R, or DVD-R (Video mode), you can
display the disc’s menu by pressing TOP
MENU or MENU.
-
-
RVideo
RVR
DVD VCD
CD
DATA DVD DATA CD
HDD
Z
DVD
To play VIDEO CDs with PBC functions
PBC (Playback Control) allows you to play
VIDEO CDs interactively using the menu on
your TV screen.
When you start playing a VIDEO CD with
PBC functions, the menu appears.
Select an item using the number buttons and
press ENTER. Then, follow the instructions
in the menu (press H when “Press
SELECT” appears).
PROG +/–
Number
buttons
AUDIO
TOP MENU
MENU
SUBTITLE
TITLE LIST
</M/m/,,
ENTER
OPTIONS
/
.
>
x
The PBC function of Super VIDEO CDs does
not work with this recorder. Super VIDEO
CDs are played in continuous play mode
only.
H
X
To change the angles
If various angles (multi-angles) for a scene
are recorded on the disc, “
” appears in
1 Press HDD or DVD.
the front panel display. Press OPTIONS
during playback to select “Change Angle,”
and press ENTER.
• If you select DVD, insert a disc (see “1.
• If you insert a DVD VIDEO, VIDEO
CD, CD, DATA DVD, or DATA CD,
press H. Playback starts.
To stop playback
Press x.
2 Press TITLE LIST.
To playback quickly with sound (Scan
Audio)
When you press M during playback of a
title recorded in the HDD, you can play
quickly with dialogue or sound (“x1.3”
appears).
For details about the Title List, see “3.
Example: DVD+RW
No sound is output when you press M two
or more times to change search speed.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
To resume playback from the point where
you stopped (Resume Play)
To lock the disc tray (Child Lock)
You can lock the disc tray to prevent children
from ejecting the disc.
When the recorder is turned on, hold down x
until “LOCKED” appears in the front panel
display. The Z (open/close) button does not
work while the Child Lock is set.
When you press H again after you stop
playback, the recorder resumes playback
from the point where you pressed x.
To start from the beginning, press OPTIONS
to select “Play Beginning,” and press
ENTER. Playback starts from the beginning
of the title/track/scene.
To unlock the disc tray, hold down x until
“UNLOCKED” appears in the front panel
display when the recorder is turned on.
The point where you stopped playing is
cleared when:
One Touch Play
If you use the SMARTLINK connection, you
can easily start playing.
Press H. The recorder and your TV
automatically turn on and the TV’s input is
switched to the recorder. Playback starts
automatically.
– you open the disc tray (except for HDD).
– you play another title (except for HDD).
– you switch the Title List menu to Original
or Playlist (HDD/DVD-RWs/DVD-Rs in
VR mode only).
– you edit the title after stopping playback.
– you change the settings on the recorder.
– you turn off the recorder (VIDEO CD/CD/
DATA DVD/DATA CD only).
One Touch Menu
If you use the SMARTLINK connection, you
can easily display the Title List.
Press TITLE LIST. The recorder and your
TV automatically turn on and the TV’s input
is switched to the recorder. The Title List
appears.
– you make a recording (except for HDD/
DVD-RWs/DVD-Rs in VR mode).
– you disconnect the mains lead.
b Note
You cannot resume playback during TV Pause.
To play restricted DVDs (Parental Control)
If you play a restricted DVD, the message
“Do you want to temporarily change the
Parental Control level to * ?” appears on your
TV screen.
z Hints
• You can also use the H button in step 3
(page 52) to start playback.
• Even if you select “Factory Setup” in the
set.
1
Select “OK” and press ENTER.
The display for entering your password
appears.
2
3
Enter your four-digit password using the
number buttons.
Press ENTER to select “OK.”
The recorder starts playback.
To register or change the password, see
,continued
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback options
To check the position of the buttons below, see the illustration on page 52.
For MP3 or JPEG operations, see “Playing MP3 Audio Tracks or JPEG Image Files” on
Buttons
Operations
AUDIO
Selects one of the audio tracks recorded on the disc when pressed
repeatedly in normal playback mode.
-
-
RVR
RWVR
HDD
: Selects the language.
DVD
HDD
DVD VCD CD
-
-
RWVR
: Selects the main or sub sound.
RVR
: Selects stereo or monaural audio tracks.
VCD CD
SUBTITLE
Selects a subtitle language when pressed repeatedly.
Replays the scene/briefly fast forwards the scene.
DVD
/
(instant replay/
instant advance)
-
+
RWVR
RW
HDD
+
-
-
RVR
RWVideo
R
-
RVideo
DVD
. (previous)/> (next)
Goes to the beginning of the previous/next title/chapter/scene/
track.
For the HDD, you cannot go to the beginning of the previous/
next title.
Fast reverses/fast forwards the disc when pressed during
playback.
(fast reverse/fast forward)
Search speed changes as follows:
fast reverse fast forward
*1
m1 T t 1M
m2 T T t t 2M
m3 T T T t t t 3M
*2
*2
When you press and hold the button, fast forward/fast reverse
continues at the selected speed until you release the button.
*1
When you press M once during playback of a title recorded in
the HDD, you can play quickly with sound (“x1.3” appears).
*2 m3 and 3M are only available for the HDD and DVDs.
Plays in slow motion when pressed for more than one second in
pause mode.
(slow, freeze frame)
Plays one frame at a time when pressed briefly in pause mode.
-
+
RW
RWVR
HDD
+
R
-
-
RVR
RWVideo
*
-
RVideo
VCD
DVD
* Playback direction only
X (pause)
Pauses playback.
To resume normal playback, press H.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
b Notes
2 Select an item, and press ENTER.
The adjustment display appears.
“FNR” (frame noise reduction):
Reduces noise contained in the
luminance element of the video signal.
“BNR” (block noise reduction):
Reduces “block noise” or mosaic like
patterns in the picture.
• Angles and subtitles cannot be changed with titles
recorded on this recorder.
• Slideshows made with a DVD camcorder can
only be played. Other play functions, such as fast
forward, cannot be used.
Notes on playing DTS sound tracks on a
CD
“MNR” (mosquito noise reduction):
Reduces the faint noise appearing around
the outlines of the images. The noise
reduction effects are automatically
adjusted within each setting range
according to the video bit rate and other
factors.
• When playing DTS-encoded CDs, excessive
noise will be heard from the analogue stereo
jacks. To avoid possible damage to the audio
system, the consumer should take proper
precautions when the analogue stereo jacks of the
recorder are connected to an amplification
system. To enjoy DTS Digital Surround™
playback, an external DTS decoder must be
connected to the DIGITAL OUT jack of the
recorder.
“Sharpness”:
Sharpens the outlines of the images.
“PB Video Equalizer” (Playback video
equalizer):
Adjusts the picture in greater detail.
Select an item and press ENTER.
• Contrast: changes the contrast.
• Brightness: changes the overall
brightness.
• Set the sound to “Stereo” using the AUDIO
button when you play DTS sound tracks on a CD
Notes on playing DVDs with a DTS sound
track
DTS audio signals are output only through the
DIGITAL OUT (COAXIAL) jack.
When you play a DVD with DTS sound tracks, set
• Colour: makes the colours deeper or
lighter.
• Hue: changes the colour balance.
3 Press </,to adjust the setting, and
press ENTER.
Adjusting the picture quality
The default settings are underlined.
+
RW
+
R
-
-
HDD
RWVR RWVideo
“FNR”: (weak) Off
“BNR”: (weak) Off
“MNR”: (weak) Off
1
1
1
2
2
2
3 (strong)
3 (strong)
3 (strong)
-
-
RVideo
RVR
DVD VCD
1 Press OPTIONS during playback to
select “Video Settings,” and press
ENTER.
“Sharpness”*: (weak) Off
(strong)
“PB Video Equalizer”:
• Contrast: (weak) –3 ~ 0 ~ 3 (strong)
• Brightness: (dark) –3 ~ 0 ~ 3 (bright)
• Colour: (light) –3 ~ 0 ~ 3 (deep)
• Hue: (red) –3 ~ 0 ~ 3 (green)
1
2
3
Repeat steps 2 and 3 to adjust any other
items.
* “1” softens the outlines of the images. “2”
enhances the outlines and “3” enhances them
more than “2.”
,continued
55
Download from Www.Somanuals.com. All Manuals Search And Download.
b Notes
• If the outlines of the images on your screen
become blurred, set “BNR” and/or “MNR” to
“Off.”
Pausing a TV Broadcast (TV
Pause)
• Depending on the disc or the scene being played,
the above BNR, MNR, or FNR effects may be
hard to discern. And, these functions may not
work with some screen sizes.
• When using the “Sharpness” function, noise
found in the title may become more apparent. In
this case, it is recommended that you use the BNR
function with the “Sharpness” function. If the
condition still does not improve, set the
“Sharpness” level to “Off.”
You can pause a current TV broadcast, and
then continue watching the programme at a
later time. This is useful when you receive an
unexpected phone call or visitor while
watching TV.
1 While viewing a TV broadcast with
this recorder, press X.
The picture pauses. You can pause the
picture for up to three hours.
Adjusting the delay between
the picture and sound (AV
SYNC)
+
+
R
-
-
HDD
RW
RWVR RWVideo
-
-
RVideo
RVR
DVD VCD
1 Press OPTIONS during playback to
select “Audio Settings,” and press
ENTER.
TV pause
2 Press X or H again to resume
2 Select “AV SYNC”, and press ENTER.
watching the programme.
“AV SYNC”:
When the video is delayed, this function
delays the audio for synchronization with
the video (0 to 120 milliseconds). Larger
numbers indicate a longer audio delay for
synchronization with the video. When
dubbing to a VCR or other video
recording equipment, be sure to return
this setting to 0 ms (default).
b Notes
• Paused titles are not saved to the HDD.
• This function is cancelled when:
– x (stop) is pressed.
– PROG +/– is pressed.
– DVD is pressed.
– Z (open/close) is pressed.
– TITLE LIST is pressed.
– INPUT SELECT is pressed.
– the recorder is turned off.
3 Press</, to adjust the setting, and
press ENTER.
– a timer recording or Synchro-Recording is
started.
– the PDC/VPS function is “On” and channel
scan is started.
– DV dubbing or regular dubbing is started.
• It may take one minute or more to resume
playback of the paused programme.
• Even if you fast forward the recorded programme,
there will always be a time difference of about
one minute or more between the recorded
programme and the current TV broadcast.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing from the beginning of
the programme you are
recording (Chasing Playback)
Playing a previous recording
while making another
(Simultaneous Rec and Play)
-
RWVR
+
RW
+
R
HDD
-
-
HDD
RWVR RWVideo
-
-
RVR
RVideo
DVD VCD
CD
“Chasing Playback” allows you to view the
recorded part of a programme while the
recording is being made. You do not need to
wait until the recording finishes.
DATA DVD DATA CD
“Simultaneous Rec and Play” allows you to
view a previously recorded programme while
recording programmes. Playback continues
even if a timer recording starts. Use this
function as follows:
Press OPTIONS while recording to select
“Chasing Playback,” and press ENTER.
Playback starts from the beginning of the
programme you are recording.
• While recording to the HDD:
Play another title on the HDD.
When you fast forward to the point that you
are recording, Chasing Playback returns to
normal playback.
Play a previously recorded programme on a
DVD by pressing DVD.
• While recording to a DVD:
Play a previously recorded programme on
the HDD by pressing HDD.
b Notes
• While recording to a DVD-RW (VR
• For DVD-RWs (VR mode), this function does not
work when recording:
*1
mode)
:
Play another title on the same DVD-RW
– on a 1x-speed DVD-RW.
*2
(VR mode) disc.
– in the HQ or HSP recording mode.
• The DVD’s picture on your TV screen freezes for
a few seconds when you fast forward/fast reverse
or instant replay/advance the recording.
• Chasing Playback is possible from one minute or
more after recording starts.
• Even if you fast forward the recorded programme,
there will always be a time difference of about
one minute or more between the recorded
programme and the current TV broadcast.
*1
Simultaneous Rec and Play function does not
work when you record:
– on a 1x-speed DVD-RW.
– in the HQ or HSP recording mode.
Picture noise may appear depending upon the
condition of the recording, or when playing a
title recorded in the HQ or HSP recording mode.
The picture freezes for a few seconds when you
use fast forward/fast reverse or instant replay/
advance.
*2
You can also play a DVD VIDEO, VIDEO
CD, Super VIDEO CD, CD, DATA DVD, or
DATA CD while recording on the HDD.
Example: Play another title on the HDD
while recording to the HDD.
1
2
3
While recording, press TITLE LIST to
display the HDD Title List.
Select the title you want to play, and
press ENTER.
Select “Play” from the sub-menu, and
press ENTER.
Playback starts from the selected title.
,continued
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Example: Play a DVD while recording to
the HDD.
Searching for a Title/
Chapter/Track, etc.
1
2
3
4
While recording, press DVD and insert
the DVD into the recorder.
Press TITLE LIST to display the DVD
Title List.
+
RW
+
R
-
-
HDD
RWVR RWVideo
-
-
RVideo
RVR
DVD VCD
CD
Select the title you want to play, and
press ENTER.
DATA DVD DATA CD
You can search a disc by title, chapter, scene
or track. As titles and tracks are assigned
individual numbers, select the title or track by
entering its number. You can also search for
a scene using the time code.
Select “Play” from the sub-menu, and
press ENTER.
Playback starts from the selected title.
b Note
You cannot play a DVD or VIDEO CD recorded in
the NTSC colour system while recording on the
HDD. When playing a VIDEO CD, be sure to set
“Colour System” to “PAL” in the “Video” setup
Number
buttons
ENTER
OPTIONS
1 Press OPTIONS during playback to
select a search method, and press
ENTER.
“Title Search” (for DVDs)
“Chapter Search” (for HDD/DVDs)
“Track Search” (for CDs/DATA CDs)
“Search” (for VIDEO CDs)
“Album Search” (for DATA DVDs/
DATA CDs)
“Time Search” (for HDD/DVDs):
Searches for a starting point by entering
the time code.
“File Search” (for DATA DVDs/DATA
CDs)
The display for entering the number
appears.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Example: Title Search
Playing MP3 Audio
Tracks or JPEG Image
Files
The number in parentheses indicates the
total number of titles, tracks, etc.
DATA DVD DATA CD
2 Press the number buttons to select the
number of the title, chapter, track,
time code, etc., you want.
You can play MP3 audio tracks and JPEG
image files on DATA CDs (CD-ROMs/CD-
Rs/CD-RWs) or JPEG image files on DATA
DVDs (DVD-ROMs/DVD+RWs/DVD+Rs/
DVD-RWs/DVD-Rs).
For example: Time Search
To find a scene at 2 hours, 10 minutes,
and 20 seconds, enter “21020.”
If you make a mistake, select another
number.
3 Press ENTER.
The recorder starts playback from the
selected number.
AUDIO
b Note
“Title Search” is not applicable to the HDD.
DISPLAY
</M/m/,,
ENTER
OPTIONS
/
.
>
M
m
H
x
X
TIME/
TEXT
1 Insert a disc.
2 Press H.
For MP3 discs, playback starts from the
first MP3 audio track on the disc.
For JPEG files, a slideshow of the
pictures on the disc begins.
If the disc contains MP3 audio tracks and
JPEG image files, only the JPEG image
files are played back when H is
pressed.
To stop playback or slideshow
Press x.
To pause playback or slideshow
Press X.
,continued
59
Download from Www.Somanuals.com. All Manuals Search And Download.
To play the beginning of the track
Press OPTIONS to select “Play Beginning,”
and press ENTER.
About MP3 audio tracks and
JPEG image files
To fast forward or review a track
MP3 is an audio compression technology that
satisfies certain ISO/MPEG regulations.
JPEG is an image compression technology.
You can play MP3 (MPEG1 Audio Layer 3)
format audio tracks and JPEG image files on
DATA CDs (CD-ROMs/CD-Rs/CD-RWs)
or JPEG image files on DATA DVDs (DVD-
ROMs/DVD+RWs/DVD+Rs/DVD-RWs/
DVD-Rs).
Press m/M during playback.
To go to the next or previous MP3 audio
track or JPEG image file
Press . or > during playback. If you
repeatedly press . or >, you will go to
the next or previous album. (MP3 audio track
only)
DATA CDs and DATA DVDs must be
recorded according to ISO9660 Level 1,
Level 2 or Joliet format for the recorder to
recognize the JPEG image files.
To go to the next or previous album
Press
/
during playback or slideshow.
To rotate a picture
DATA CDs must be recorded according to
ISO9660 Level 1, Level 2 or Joliet format for
the recorder to recognize the MP3 tracks.
You can also play discs recorded in
Press OPTIONS while the JPEG image is
displayed to select “Rotate Right” or “Rotate
Left,” and press ENTER.
z Hints
MultiSession/Border.
• Press the AUDIO button to switch between
stereo or monaural audio tracks.
• You can rotate a JPEG image by using the </,
buttons when the image is displayed.
• Press DISPLAY repeatedly to show information
about the JPEG album or image on your TV
screen. Then press TIME/TEXT to toggle
between the current selected image number and
album number.
See the instructions supplied with the disc
drives and the recording software (not
supplied) for details on the recording format.
Note on MultiSession/Border discs
If audio tracks and images in Music CD
format or Video CD format are recorded in
the first session/border, only the first session/
border will be played back.
b Notes
• Some JPEG files, especially files of three million
pixels or more, may lengthen the slideshow
interval.
b Note
The recorder may not be able to play some DATA
CDs created in the Packet Write format.
• Rotated JPEG images will not be saved when you
switch to another folder.
• Images larger than 720 × 480 will be reduced to
720 × 480 when displayed.
• The following images are not displayed:
– progressive JPEG image files
MP3 audio tracks or JPEG
image files that the recorder
can play
– greyscale JPEG image files
– 4:1:1 JPEG image files
The recorder can play the following tracks
and files:
– MP3 audio tracks with the extension
“.mp3.”
• When you attempt to play a broken file or a file
that does not satisfy the play conditions,
appears but the recorder cannot play the file.
– JPEG image files with the extension “.jpeg”
or “.jpg.”
– JPEG image files that conform to the DCF*
image file format.
* “Design rule for Camera File system”: Image
standards for digital cameras regulated by JEITA
(Japan Electronics and Information Technology
Industries Association).
60
Download from Www.Somanuals.com. All Manuals Search And Download.
b Notes
When you insert a DATA CD/DATA DVD
and press H, the numbered tracks (or files)
are played sequentially, from 1 through 7.
• The recorder will play any data with the extension
“.mp3,” “.jpeg,” or “.jpg,” even if they are not in
MP3 or JPEG format. Playing these data may
generate a loud noise which could damage your
speaker system.
For JPEG image files, press
to go to the
next album. (For instance, when you want to
go from 1 to 2.) Any sub-albums/tracks (or
files) contained within a currently selected
album take priority over the next album in the
same tree. (Example: C contains D so 4 is
played before 5.)
• The recorder does not conform to audio tracks in
mp3PRO format.
• Some files cannot be played.
About playback order of
albums, tracks, and files
z Hints
• If you add numbers (01, 02, 03, etc.) to the front
of the track/file names when you store the tracks
(or files) in a disc, the tracks and files will be
played in that order.
Albums play in the following order:
Structure of disc contents
• Since a disc with many trees takes longer to start
playback, it is recommended that you create
albums with no more than two trees.
Tree 1 Tree 2 Tree 3 Tree 4 Tree 5
ROOT
b Notes
• Depending on the software you use to create the
DATA DVD/DATA CD, the playback order may
differ from the above illustration.
• No more than a total of 999 individual folders can
be played. (Folders that do not contain JPEG/
MP3 files are counted as well.)
• No more than a total of 999 folders and 9999 files
can be played. (Files other than JPEG/MP3 files,
and folders that do not contain JPEG/MP3 files
are counted as well.)
• No more than 999 folders and files can be
recognized in a single folder. (Folders that do not
contain JPEG/MP3 files are counted as well.)
• Proceeding to the next or another album may take
some time.
• This recorder supports MP3 audio bit rates up to
320 kbps.
Album
MP3 audio track/
JPEG image file
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Erasing and Editing
Before Editing
This recorder offers various edit options for
various disc types.
b Notes
• You may lose the edited contents if you remove
the disc or a timer recording starts while editing.
• DVD discs created by DVD video cameras
cannot be edited on this recorder.
• If a message appears and indicates that the disc’s
control information is full, erase or edit
unnecessary titles.
• When editing a DVD+R or DVD-R, finish all
editing before finalising the disc. You cannot edit
a finalised disc.
-
RWVR
HDD
+
RW
-
RVR
-
RWVideo
Edit features
+
R
Original
title
Playlist
title
Original
title
Playlist
title
-
RVideo
Erase (page 63)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
No
Yes
Yes
Yes
Yes*
Yes
No
Protect (page 63)
Title Name (page 63)
A-B Erase (page 64)
Erase Titles (page 64)
Divide (page 65)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Set Thumbnail (page 63)
Chapter mark (page 66)
Yes
Yes
Yes
No
No
No
Change Order (page 68)
Combine (page 69)
No
No
No
No
No
Yes
Yes
No
No
Yes
* DVD+RW only
62
Download from Www.Somanuals.com. All Manuals Search And Download.
To open up disc space
To open up disc space on a DVD+RW or
DVD-RW (Video mode), erase the title with
the largest number in the title list.
Erasing and Editing a
Title
Largest title number
+
RW
-
-
+
R
RWVR RWVideo
HDD
-
-
RVideo
RVR
This section explains the basic edit functions.
Note that editing is irreversible. To edit the
HDD or DVD-RWs/DVD-Rs (VR mode)
without changing the original recordings,
For the HDD and DVD-RWs (VR mode),
you can erase any title.
For DVD-Rs and DVD+Rs, the available disc
space does not increase even if you erase
titles.
CHAPTER
MARK
CHAPTER
ERASE
MARK
TITLE LIST
</M/m/,,
ENTER
O
RETURN
OPTIONS
To switch between the Playlist and
Original Title List
>
.
mc
CM
You can display the Playlist titles in the Title
List (Playlist), or the Original titles in the
Title List (Original). To switch the two Title
Lists, press </, while a Title List is
displayed. To create and edit a Playlist, see
X
1 Press TITLE LIST.
For HDD titles or DVD-RWs/DVD-Rs
in VR mode, press </, to switch the
Title Lists, if necessary.
2 Select a title, and press ENTER.
The sub-menu appears.
3 Select an option, and press ENTER.
You can make the following edits to the
title.
“Erase”: Erases the selected title. Select
“OK” when asked for confirmation.
“Protect”: Protects the title. “ ” appears
next to the protected title.
“Title Name”: Allows you to enter or re-
“A-B Erase”: Erases a section of the title
“Divide”: Divides a title into two titles
,continued
63
Download from Www.Somanuals.com. All Manuals Search And Download.
“Set Thumbnail”: Changes the title’s
thumbnail picture that appears in the
“Make a Playlist”: Adds the entire title to
5 When you finish selecting titles,
select “OK,” and press ENTER.
The list of the titles to be erased appears
for confirmation.
• To change the selection, select
“Change,” and repeat from step 3.
6 Select “OK” and press ENTER.
z Hints
The titles are erased.
• You can erase multiple titles at one time
• You can automatically erase titles that have
To erase all titles on the disc
You can reformat the HDD, DVD+RW, or
DVD-RW to make the disc or drive blank.
To format the HDD, see “Format” on
b Note
DVD-RW/DVD-R (VR mode) playlist titles cannot
be protected.
To format a DVD+RW or DVD-RW disc, see
Erasing multiple titles (Erase
Titles)
Erasing a section of a title
(A-B Erase)
+
RW
-
-
+
R
RWVR RWVideo
HDD
-
-
RVideo
RVR
+
RW
-
RWVR
-
RVR
HDD
You can select and erase more than one title
at one time using the OPTIONS menu.
You can select a section (scene) in a title and
erase it. Note that erasing scenes in a title
cannot be undone.
1 Press TITLE LIST.
For HDD titles or DVD-RWs/DVD-Rs
in VR mode, press </, to switch the
Title Lists, if necessary.
Title,” select “A-B Erase” and press
ENTER.
2 Press OPTIONS to select “Erase
Titles,” and press ENTER.
The display for selecting titles to be
erased appears.
The display for setting point A appears.
The title starts to play.
• To return to the beginning of the title,
press X and then press ..
3 Select a title, and press ENTER.
A check mark appears in the check box
next to the selected title.
Playback point
• To clear the check mark, press ENTER
again.
• To clear all of check marks, select
“Reset.”
2 Select point A using m/M, and
press ENTER.
Playback pauses.
4 Repeat step 3 to select all of the titles
you want to erase.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Press ENTER if point A is correct.
If point A is incorrect, select point A
using c/C, and press ENTER. The
display for setting point B appears.
Dividing a title (Divide)
*
*
-
-
RVR
RWVR
HDD
If you want to dub a long title to a disc but do
not want to reduce the picture quality, divide
the title into two shorter titles. Note that
dividing a title cannot be undone.
* Only playlist titles can be divided for DVD-RWs/
DVD-Rs (VR mode).
4 Select point B using m/M, and
press ENTER.
Playback pauses.
5 Press ENTER if point B is correct.
If point B is incorrect, select point B
using c/C, and press ENTER. The
display asks for confirmation.
• To reset point A, press M and
O RETURN, and go to step 2.
• To reset point B, press M and repeat
step 4.
1 Press TITLE LIST.
Press </, to switch the Title Lists, if
necessary.
2 Select a title, and press ENTER.
The sub-menu appears.
• To preview the title without scenes to
be erased, select “Preview” (except for
DVD+RWs).
3 Select “Divide,” and press ENTER.
The display for setting the dividing point
appears, and the title starts to play.
• To return to the beginning of the title,
press X and then press ..
6 Select “OK,” and press ENTER.
The scene is erased. The display for
setting point A appears.
• To continue, go to step 2.
• To finish, select “Quit.”
z Hint
A chapter mark is inserted after the scene was
erased. The chapter mark divides the title into
separate chapters on either side of the mark.
b Notes
• Images or sound may be momentarily interrupted
at the point where you erase a section of a title.
• Sections shorter than five seconds may not be
erased.
4 Select the dividing point by pressing
m/M, and press ENTER.
Playback pauses.
• For DVD+RWs, the erased section may be
slightly different from the points you selected.
5 Press ENTER if the dividing point is
correct.
If the dividing point is incorrect, select
the dividing point using c/C, and
press ENTER. The display asks for
confirmation.
• To change the dividing point, press M.
6 Select “OK,” and press ENTER.
The title is divided in two.
z Hint
After a title is divided, the title name prior to
division is assigned to both the first and second
parts.
,continued
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating chapters manually
Creating and Editing a
Playlist
-
-
RVR
RWVR
HDD
You can manually insert a chapter mark at
any point you like during playback or
recording.
-
RWVR
-
RVR
HDD
Playlist edit allows you to edit or re-edit
without changing the actual recordings. You
can create up to 97 Playlist titles.
Press CHAPTER MARK at the point where
you want to divide the title into chapters.
Each time you press the button, “Marking ...”
appears on the screen and the scenes to the
left and right of the mark become separate
chapters.
Example: You have recorded the final few
matches of a football tournament on a DVD-
RW/DVD-R (VR mode). You want to create
a digest with the goal scenes and other
highlights, but you also want to keep the
original recording.
To erase chapter marks
You can combine two chapters by erasing the
chapter mark during playback.
Original
Press ./> to search for a chapter
number, and while displaying the chapter
containing the chapter mark you want to
erase, press CHAPTER MARK ERASE.
The current chapter combines with the
previous chapter.
Playlist
b Notes
In this case, you can compile highlight scenes
as a Playlist title. You can even rearrange the
scene order within the Playlist title.
The Playlist title calls up data from the
original titles for playback. When an original
title is used for a Playlist title, the original
title cannot be edited and erased.
• When dubbing, any chapter marks you enter will
be erased.
• To insert a chapter mark manually during
recording, set “Auto Chapter” to “Off” in the
“Recording” setup.
b Note
Playlist titles containing titles recorded with the
“Copy-Once” copy protection signal cannot be
66
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Press TITLE LIST.
7 Select the OUT point using m/M,
and press ENTER.
If the Title List (Original) appears, press
<.
Playback pauses.
2 Press OPTIONS to select “Create a
Playlist,” and press ENTER.
8 Press ENTER if the OUT point is
correct.
If the OUT point is incorrect, select the
OUT point using c/C, and press
ENTER.
The selected scene is added to the scene
list.
• To add more scenes, go to step 5.
9 When you finish adding scenes, press
m.
3 Select “Select,” and press ENTER.
4 Select the title you want to include in
the Playlist title, and press ENTER.
The display for setting the start point (IN)
appears. The title starts to play.
A Total duration of the selected
scene
B Total number of scenes
• To return to the beginning of the title,
press X and then press ..
C Selected scene
10 Select the scene you want to re-edit,
and press ENTER.
The sub-menu appears.
“Move”: Changes the scene order using
</, and press ENTER.
“Erase”: Erases the scene. When asked
for confirmation, select “OK.”
• To add more scenes, press M and go to
step 5.
• To add more scenes from another title,
select “Select” and go to step 4.
• To preview all of the captured scenes in
the listed order, select “Preview.”
5 Select the IN point using m/M,
and press ENTER.
Playback pauses.
6 Press ENTER if the IN point is correct.
If the IN point is incorrect, select the IN
point using c/C, and press ENTER.
The display for setting the end point
(OUT) appears.
11 When you finish editing the scene list,
select “OK,” and press ENTER.
The title of the created Playlist is added
to the Title List (Playlist). The title name
is the title name of the first scene.
,continued
67
Download from Www.Somanuals.com. All Manuals Search And Download.
z Hint
When a Playlist title is created, the IN and OUT
points will become chapter marks, and each scene
will become a chapter.
Moving a Playlist title (Change
Order)
-
-
RVR
RWVR
b Note
The picture may pause when the edited scene is
played.
You can change the Playlist title order within
the Title List (Playlist).
To add the entire title to the Playlist title
as one scene (Make a Playlist)
1 Press TITLE LIST.
If the Title List (Original) appears, press
1
2
3
Press TITLE LIST. If the Title List
(Playlist) appears, press ,.
<.
2 Press OPTIONS to select “Change
Order,” and press ENTER.
Select the title and press ENTER.
The sub-menu appears.
Select “Make a Playlist,” and press
ENTER.
The selected title is added to the Title List
(Playlist).
The title name is the same as the Original
title name.
To play the Playlist title
3 Select the title you want to move, and
press ENTER.
1
2
3
Press TITLE LIST. If the Title List
(Original) appears, press <.
4 Select a new location for the title
using M/m, and press ENTER.
The title moves to the new location.
• To move more titles, go to step 3.
• To finish, select “Quit,” and press
ENTER.
Select a title, and press ENTER.
The sub-menu appears.
Select “Play,” and press ENTER.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
z Hint
After titles are combined, the title name is the title
name of the first title prior to combination.
Combining multiple Playlist
titles (Combine)
b Note
-
-
RVR
RWVR
HDD
When the number of chapters in the title to be
combined exceeds the limit, the chapters at the end
are combined into a single chapter.
1 Press TITLE LIST.
If the Title List (Original) menu appears,
press <.
Dividing a Playlist title (Divide)
2 Press OPTIONS to select “Combine,”
and press ENTER.
-
-
RVR
RWVR
HDD
The display for selecting titles appears.
You can divide a Playlist title. For operations,
3 Select a title, and press ENTER.
A number indicating the order in which
you selected the title appears.
To cancel the selection, press ENTER
again.
4 Repeat step 3 to select all of the titles
you want to combine.
To cancel all of the selections, select
“Reset.”
5 Select “OK,” and press ENTER.
The list of titles to be combined appears.
To change the selection, select “Change”
and go to step 3.
6 Select “OK,” and press ENTER.
The titles are combined.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
b Notes
• You cannot make a recording while dubbing.
• To play a dubbed disc on other DVD equipment,
Dubbing (HDD y DVD)
• You cannot dub from DVD VIDEOs to the HDD.
• Thumbnails that you have set for the originally
dubbed title.
• When dubbing to a DVD+R DL disc, the video
may be momentarily interrupted at the point
where the layers switch.
Before Dubbing
+
RW
-
-
+
R
RWVR RWVideo
HDD
-
-
RVideo
RVR
In this section, “dubbing” refers to “copying
a recorded title on the internal hard disk drive
(HDD) to another disc, or vice versa.” You
can select to dub one title at a time (Title
Dubbing)” on page 73), or multiple titles all
at once (Multiple Title Dubbing – see
About “Dub Mode”
With this recorder, the recording mode for
dubbing is displayed as “Dub Mode.” Three
dubbing methods are available: High-speed
Dubbing, Original Dubbing, and Rec Mode
Conversion Dubbing. Read the following and
select according to the required time, disc
space, and picture quality.
Before you start, read the following
precautions, which are common to both
dubbing methods.
Dubbing at high-speed (High-speed
Dubbing)
If you want to record from a digital video
camera connected to the DV IN jack, see
“DV Dubbing” on page 76. To record from
equipment connected to the LINE IN jacks,
+
-
-
,
/
/
RWVR / RWVideo
/
RW
HDD
/
-
+
-
RVideo
RVR
R
Allows you to dub what you have stored in
the HDD to a high-speed DVD (8x-speed
DVD+RWs/6x-speed DVD-RWs/16x-speed
DVD+Rs/16x-speed DVD-Rs, or slower
versions of each disc type), without changing
the recording mode.
Set “Dub Mode” to “Fast” in the steps of
When dubbing multiple titles, you can select
“Fast” if there are one or more titles that can
be dubbed at high speed in the selected titles.
However, titles that cannot be dubbed at high
speed are dubbed in the Original Dubbing
mode.
Before you start…
• You cannot record both the main and sub
sound on DVD+RWs, DVD-RWs (Video
mode), DVD+Rs, or DVD-Rs (Video
mode). For bilingual programmes, set
“Bilingual Recording” of “DVD Rec.
Settings” to either “Main” (default) or
• The chapter marks in the dubbing source
are not retained in the dubbed title. When
“Auto Chapter” is set to “On” in the
“Recording” setup, chapter marks are
automatically inserted at approximately
6 minute intervals.
The minimum required time is as follows
(approximate).
z Hints
• When you dub a Playlist title, it is recorded as an
Original title.
• When dubbed from a DVD to the HDD, the
picture size and the sound types originally
recorded are retained.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
b Notes
Required times for High-speed Dubbing from
HDD to DVD (for 60-minute programme)
*1
• High-speed Dubbing is not available for the
following titles:
Speed*2 6x
6x
8x
8x
2.4x
– Titles recorded in HQ+.
– Titles that contain both main and sub sounds
(except DVD-RWs/DVD-Rs (VR mode)).
– Titles recorded in mixed picture size (4:3 and
16:9 etc.) (except DVD-RWs/DVD-Rs (VR
mode)).
High- High-
Rec. speed speed
mode DVD- DVD+
High- High- DVD+R
speed speed (Double
DVD-R DVD+R Layer)
RW
RW
– Dubbing from DVD to HDD
– Dubbing 16:9 size title from HDD to
DVD+RW/DVD+R
– When dubbing a title with a picture size of 16:9
recorded in LP, EP, or SLP mode to a DVD-RW
or DVD-R in Video mode.
HQ
Approx. Approx. Approx. Approx. Approx.
10min. 10min. 8 min. 8 min. 25min.
HSP Approx. Approx. Approx. Approx. Approx.
6 min. 6 min. 5 min. 5 min. 16min.
40 sec. 40 sec.
40 sec.
• When dubbed to a DVD-RW (Video mode)/
DVD+RW/DVD+R/DVD-R (Video mode), the
“seams” that are left over from editing may
remain on the disc. If you edit a title, use the
Original Dubbing or Rec Mode Conversion
Dubbing method. This will smooth out the
“seams.”
SP
Approx. Approx. Approx. Approx. Approx.
5 min. 5 min. 3 min. 3 min. 12min.
45 sec. 45 sec. 30 sec.
LSP
ESP
Approx. Approx. Approx. Approx. Approx.
4 min. 4 min. 3 min. 3 min. 10min.
Approx. Approx. Approx. Approx. Approx.
3 min. 3 min. 2 min. 2 min. 8 min.
20 sec. 20 sec. 30 sec. 30 sec. 20 sec.
Original Dubbing
+
-
-
RWVideo
n
/
/
/
/
/
RWVR
RW
HDD
LP
Approx. Approx. Approx. Approx. Approx.
2 min. 2 min. 2 min. 2 min. 6 min.
-
+
RVR
-
RVideo
R
Original Dubbing allows you to make smooth
dubbings by de-emphasizing the “seams” that
are left over from editing. In this case, the
recording mode is set to the same recording
mode that the source title was recorded in.
To set the “Dub Mode” to “Original,” you
must make your selection from the “Dub
30 sec. 30 sec.
15 sec.
EP
Approx. Approx. Approx. Approx. Approx.
1 min. 60 1 min. 60 60
*3
*3
*3
40 sec. min. 15 sec. min. min.
SLP
Approx. Approx. Approx. Approx. Approx.
1 min. 60
15 sec. min.
56 sec. 60
60
*3
*3
*3
min. min.
Note that you cannot select “Original” when
using the Dubbing method explained in
*1
*2
The values in the above table are for reference
only. Actual times for dubbing also require time
for creating disc’s control information and other
data.
This is the maximum recording speed of this
recorder. The recording speed cannot exceed the
value indicated in the above table even when
using discs that support higher recording speeds.
In addition, depending on the disc condition, the
recorder may be unable to record at the
maximum recording speed indicated in the table.
High-speed dubbing is not available when
dubbing titles recorded in EP and SLP mode to
DVD+RWs and DVD+Rs.
b Note
If the recording mode of the dubbing source title is
unknown when dubbing from a DVD to the HDD,
“Dub Mode” is automatically set to “SP” in the
*3
,continued
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec Mode Conversion Dubbing
Dubbing restriction
+
-
-
You cannot dub movies and other DVD
VIDEOs to the HDD. Also, when dubbing
from a DVD to the HDD, a grey, blank screen
will be recorded for scenes that contain a
copy protection signal.
n
/
/
/
/
/
RWVR
RWVideo
RW
HDD
-
+
R
RVR
-
RVideo
Allows you to dub from the HDD to a DVD
or vice versa, in a dubbing mode that differs
from the original recordings. For example,
when you dub an HQ title (data size is large)
in SP mode, you can reduce the data size,
saving more titles using less space.
Copy
protection
signals
Dubbing
Select a mode different from the original
recording in “Dub Mode” in the steps of
Selected Titles)” (page 74). When dubbing
multiple titles, all of the selected titles will be
recorded in same recording mode.
Copy-Free
(No copy
protection
signal)
-
+
RWVR
RW
,
,
-
+
RWVideo
R
HDD
HDD
-
-
RVideo
RVR
Copy-Once
*
*
-
RWVR
,
-
RVR
z Hint
Dubbing in the recording mode of the source title
smoothes out the “seams” that are left over from
editing.
* CPRM-compatible DVD-RWs/DVD-Rs (VR
mode) only
CPRM (Content Protection for Recordable
Media) is a coding technology that protects
copyrights for images.
b Notes
• For a title whose picture size (16:9 or 4:3) is
mixed:
Move
HDD
– When dubbed from the HDD to DVD-RWs/
DVD-Rs (Video mode), the picture size is
determined by the setting in “DVD Rec. Picture
– When dubbed from the HDD to DVD-RWs/
DVD-Rs (Video mode) in LP, EP or SLP mode,
the picture size is always 4:3.
– When dubbed from HDD to DVD+RW or
DVD+R, the picture size is always 4:3.
• The picture quality will not improve even if a title
is converted to a recording mode of better picture
quality.
-
-
,
RWVR / RVR
Titles containing “Copy-Once” copy
protection signals can be moved only from
HDD to DVD-RW/DVD-R (VR mode)*
(after the title is moved, the original title in
the HDD is erased). The “Move” function is
performed using the same procedure as
Once” copy protection signals are indicated
with
.
b Notes
• The following titles in the HDD cannot be moved.
– Protected titles
– Playlist titles
– Original titles referenced from the playlist
• When dubbing (Move) is stopped partway, no
part of the title will be moved to the dubbing
target. However, note that this will decrease the
free disc space for DVD+Rs/DVD-Rs.
• Even if you erase a scene that contains a copy
protection signal, the recording restrictions on
that title are retained.
* CPRM-compatible DVD-RWs/DVD-Rs (VR
mode) only.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Select “Dub Mode.”
Dubbing
7 Select a dubbing mode using M/m.
Fast*
+
RW
-
-
+
R
RWVR RWVideo
HDD
-
-
RVideo
RVR
* From the HDD to a DVD only.
Appears when High-speed Dubbing is
Dubbing a single title (Title
Dubbing)
8 Select “Start,” and press ENTER.
The remaining time of dubbing appears
in the front panel display.
1 Insert the DVD that you are going to
dub to or from.
2 Press HDD or DVD to select the
source.
To automatically adjust the dubbing mode
If there is not enough available space on the
target disc, the recorder automatically selects
a dubbing mode with lower picture quality
according to the available space. If there is
insufficient disc space in the selected
dubbing mode, the following display appears
after step 8.
3 Press TITLE LIST.
Press </, to switch the Title Lists, if
necessary.
4 Select a title, and press ENTER.
The sub-menu appears.
5 Select “Dubbing,” and press ENTER.
The display for selecting the dubbing
mode appears.
If a title with
(page 72) is selected
in the title list, a confirmation display is
displayed.
To “Move,” select “OK.”
Select “OK” and go to step 8.
To manually select another dubbing mode,
select “Cancel,” and go to step 7.
To stop dubbing
Press OPTIONS to select “Stop Dubbing,”
and press ENTER. When asked for
confirmation, select “OK,” and press
ENTER.
A Size of the title (approximate)
This is displayed in red when the size
exceeds the available space on the
dubbing target media.
When dubbing (Move) is stopped partway,
no part of the title will be moved to the
dubbing target. However, note that this will
decrease the free disc space for DVD+Rs/
DVD-Rs.
B Direction of dubbing
z Hint
C Available space on the disc to be
You can turn off the recorder during dubbing. The
recorder completes dubbing even after being turned
off.
dubbed (approximate)
D Information about the title to be
dubbed
E Dubbing mode and the space that
remains after dubbing
(approximate)
,continued
73
Download from Www.Somanuals.com. All Manuals Search And Download.
E
: Indicates titles containing
“Copy-Once” copy protection
signals (page 72). When you select
Dubbing multiple titles (Dub
Selected Titles)
a title with
for confirmation. To “Move,”
select “OK.”
, the display asks
A maximum of 30 selected titles can be
dubbed at once.
F Order of dubbing
1 Insert the DVD that you are going to
dub to or from.
6 Repeat step 5 to select all of the titles
you want to dub.
2 Press HDD or DVD to select the
source.
7 Select “OK,” and press ENTER.
The display for selecting the dubbing
mode appears.
3 Press TITLE LIST.
Press </, to switch the Title Lists, if
necessary.
8 Select a dubbing mode using M/m.
4 Press OPTIONS to select “Dub
Selected Titles,” and press ENTER.
Fast*
Original
5 Select titles in the order you want to
dub, and press ENTER.
The titles are numbered in the selected
order.
* From the HDD to a DVD only.
Appears when available for the title
9
Select “Start,” and press ENTER.
The remaining time of dubbing appears
in the front panel display.
• To cancel the selection, press ENTER
again.
• To cancel all of the selections, select
“Reset.”
To automatically adjust the dubbing mode
If there is not enough available space on the
target disc, the recorder automatically selects
a dubbing mode with lower picture quality
according to the available space. The same
dubbing mode is set for all of the titles. If disc
space is insufficient for the selected dubbing
mode, the following display appears after
step 9 of “Dubbing multiple titles (Dub
A Total size of the selected titles
This is displayed in red when the size
exceeds the available space on the
dubbing target media.
B Direction of dubbing
C Available space on the disc to be
dubbed (approximate)
Select “OK” and go to step 9.
To manually select another dubbing mode,
select “Cancel,” and go to step 8.
D “PL”: Indicates a Playlist title.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
To stop dubbing
Press OPTIONS to select “Stop Dubbing,”
and press ENTER. When asked for
confirmation, select “OK,” and press
ENTER.
When dubbing (Move) is stopped partway,
no part of the title will be moved to the
dubbing target. However, note that this will
decrease the free disc space for DVD+Rs/
DVD-Rs.
z Hint
You can turn off the recorder during dubbing. The
recorder completes dubbing even after being turned
off.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
b Notes
• You cannot make a recording while DV dubbing.
• The DV IN jack is for input only. It will not
output signals.
DV Dubbing
• You cannot use the DV IN jack when:
– signal input to the DV IN jack on the front panel
or recorder operation cannot be performed
correctly when using a digital video camera
camera to the LINE IN jack and follow the
instructions of “Recording from connected
– the input signal is not in DVC-SD format. Do
not connect a MICRO MV format digital video
camera even if it has an i.LINK jack.
– the images on the tape contain copy protection
signals, which limit recording.
Before DV Dubbing
This section explains dubbing with a digital
video camera via the DV IN jack on the front
panel. If you want to dub by way of the LINE
IN jacks, see “Recording from connected
The DV IN jack on this recorder conforms to
the i.LINK standard.
Follow the instructions in “Preparing for DV
dubbing,” and then move on to the section on
dubbing. For more information about
i.LINK, see “About i.LINK” on page 106.
• If you want to play the disc on other DVD
Hookups
DVD recorder
Preparing for DV dubbing
You can connect a digital video camera to the
DV IN jack on the recorder to record or edit
from a DV/Digital8 format tape. Operation is
straightforward because the recorder will fast
forward and rewind the tape for you – you do
not need to operate your digital video camera.
Do the following to start using the “DV Edit”
functions of this recorder.
to DV IN
i.LINK cable (not supplied)
See the instruction manual supplied with the
digital video camera as well before
connecting.
DV output
z Hint
If you plan to do additional editing on a disc after
the initial dub, use the DV IN jack and record on a
DVD-RW/DVD-R (VR mode) or HDD.
Digital video camera
: Signal flow
1 Press HDD or DVD to select the
recording destination.
If you select DVD, insert a disc (see “1.
2 Insert the source DV/Digital8 format
tape into your digital video camera.
For the recorder to record or edit, your
digital video camera must be set to video
playback mode.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
b Notes
3 Press INPUT SELECT on the remote
repeatedly to select “DV.”
The front panel display changes as
follows:
• You cannot connect more than one piece of
digital video equipment to the recorder.
• You cannot control the recorder using another
device or another recorder of the same model.
• You cannot record date, time, or the contents of
the cassette memory onto the disc.
programme
position
• If you record from a DV/Digital8 format tape that
is recorded in multiple sound tracks, such as a
tape with multiple sampling frequencies (48 kHz,
44.1 kHz, or 32 kHz), no sound or an unnatural
sound will be output when playing back the
sampling frequency switch point on the disc.
• In order to use this recorder’s “Auto Chapter”
clock on your digital video camera before
shooting.
4 Press REC MODE on the remote
repeatedly to select the recording
mode.
The recording mode changes as follows:
• The recorded picture may be momentarily
affected or the start and end points of a title may
be different from what you have set if the source
DV/Digital8 format tape is in any of the following
conditions. In this case, see “Recording from
– There is a blank space in the recorded portion of
the tape.
For details about the recording mode, see
5 Press OPTIONS on the remote to
select “DV Audio Input,” and press
ENTER. Then, select the setting for the
audio input.
– The tape’s time code is not sequential.
– If the picture size or the recording mode on the
tape being dubbed changes.
“Stereo1” (default): Records original
sound only. Normally select this when
dubbing a DV format tape.
“Mix”: Records both stereo 1 and 2.
“Stereo2”: Records additional audio
only.
Select “Mix” or “Stereo2” only if you
have added a second audio channel when
recording with your digital video camera.
You are ready to start dubbing. Select
one of the dubbing methods on the
following pages.
6 Adjust the dubbing picture quality and
size.
Before dubbing starts, press OPTIONS
to select “Rec Settings,” and adjust the
z Hint
You can turn off the recorder during dubbing. The
recorder completes dubbing even after being turned
off.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
b Notes
• When a blank space between the recordings on
the tape continues for more than five minutes,
One Touch Dubbing ends automatically.
• The recorder records a blank for five minutes
before it stops dubbing. To stop the blank
recording, press x REC STOP.
Recording an Entire DV
Format Tape (One Touch
Dubbing)
+
RW
-
-
+
R
RWVR RWVideo
HDD
-
-
RVideo
RVR
You can record the entire contents of a DV/
Digital8 format tape onto a disc with a single
press of the ONE-TOUCH DUB button on
the recorder. The recorder controls the digital
video camera for the whole process, and
completes the recording.
How chapters are created
The contents dubbed to the HDD or DVD
become a single title. When “Auto Chapter”
is set to “On” in the “Recording” setup, this
title is divided into chapters. When dubbing
to the HDD or a DVD-RW/DVD-R (VR
mode), each shooting session on the tape
becomes a chapter on the disc. For other
discs, the recorder divides the title into
chapters at approximately 6 minute intervals.
Follow steps 1 to 6 of “Preparing for DV
dubbing” on page 76, and press ONE-
TOUCH DUB on the recorder.
The recorder rewinds the tape and then starts
recording the tape contents.
When the recording is finished, the recorder
rewinds the tape in the digital video camera.
To stop during recording
Press x REC STOP.
Note that it may take a few seconds for the
recorder to stop recording.
z Hints
• If you set “Finalise Disc” of “One Touch
Dubbing” to “Auto” in the “DVD” setup
(page 94), the recorded disc (except DVD-RW
(VR mode)) will automatically be finalised after
recording is finished.
• You can play back a previously recorded title on
the HDD while One Touch Dubbing is in
progress.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
DV dubbing” on page 76, and press
SYSTEM MENU.
Program Edit
+
-
-
+
R
RWVR RWVideo
HDD
RW
2 Select “DV EDIT,” and press ENTER.
The display asks if you want to start
selecting scenes.
-
-
RVR
RVideo
You can select scenes from a DV/Digital8
format tape, and then automatically record
selected scenes to the HDD or a DVD.
To use this function, do the following:
Connect your digital video camera and
prepare for recording
m
• If you have previously saved a
Select and edit the scenes you want to dub
programme, the display asks if you
want to edit an existing programme or
to create a new programme. To resume
editing the existing programme, select
“Saved Data,” and go to step 9.
Using the recorder’s remote control, fast
forward or rewind the tape to select the
scenes. At this point, the selected scenes are
not copied to the disc. The recorder only
remembers the IN and OUT points of the
scenes that you selected for dubbing. You can
also erase or change the order of the scenes.
m
3 Select “Start,” and press ENTER.
The display for setting the IN point (start
of the scene) appears.
The scene starts to play.
Dub the selected scenes
After you have selected the scenes, the
recorder will fast forward and rewind the tape
automatically and record the scenes to the
HDD or a DVD.
How chapters are created
The contents dubbed to the HDD or DVD
become a single title. When “Auto Chapter”
is set to “On” in the “Recording” setup, this
title is divided into chapters. When dubbing
to the HDD or a DVD-RW/DVD-R (VR
mode), each shooting session on the tape and
each selected scene becomes a chapter on the
disc. For other discs, the recorder divides the
title into chapters at approximately 6 minute
intervals.
4 Select the IN point using m/M,
and press ENTER.
Playback pauses.
5 Press ENTER if the IN point is correct.
If the IN point is incorrect, select the IN
point using c/C, and press ENTER.
The display for setting the OUT point
(end of the scene) appears.
6 Select the OUT point using m/M,
and press ENTER.
Playback pauses.
,continued
79
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Press ENTER if the OUT point is
correct.
10 When you finish editing the scene list,
select “OK,” and press ENTER.
The display for entering the title name
appears. To enter a new name, select
“Enter,” and follow the explanations on
If the OUT point is incorrect, select the
OUT point using c/C, and press
ENTER.
The selected scene is added to the scene
information block.
• To add more scenes, go to step 4.
8 When you finish adding scenes, press
m.
The scene list is displayed.
11 Select “OK,” and press ENTER.
The title name is fixed, and the display
asks if you want to start recording.
To change the disc media, select “Media”
and press M/m. To change the dubbing
mode, select “Dub Mode” and press M/
m.
Data capacity required for the dubbing.
This is displayed in red when the size
exceeds the available space on the
dubbing target media.
A Total duration of the scene
B Total number of scenes
C Scene information block
9 Select the scene information block
you want to edit using </,, and
press ENTER.
The sub-menu appears.
“Move”: Changes the scene order using
</, and ENTER.
“Erase”: Erases the scene. When asked
for confirmation, select “OK.”
“Preview”: Plays the selected scene.
• To add more scenes, press M and go to
step 4.
12 Select “Start,” and press ENTER.
The recorder starts recording the tape
contents as programmed.
To stop during recording
Press x REC STOP.
Note that it may take a few seconds for the
recorder to stop recording.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
To automatically adjust the dubbing mode
If there is not enough available space on the
target disc, the recorder automatically selects
a dubbing mode with lower picture quality
according to the available space. The same
dubbing mode is set for all of the titles. If disc
space is insufficient for the selected dubbing
mode, the following display appears after
step 12.
Select “OK” and go to step 12.
If you do not want to change the dubbing
mode, select “Cancel.” However, note that
dubbing will end before the title is finished.
b Notes
• If you set the beginning of the tape as the IN point
and the end point as the OUT point, the IN and
OUT points may move slightly during dubbing.
• You cannot set a scene to be shorter than one
second.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
Select “Channel Setting” in “Basic,” and
press ENTER.
Settings and Adjustments
Aerial Reception and
Language Settings
(Basic)
The “Basic” setup helps you to make tuner,
clock, and programme position settings for
the recorder.
Press M/m to select the programme
position, and press ENTER.
1 Press SYSTEM MENU while the
recorder is in stop mode.
2 Select “SETUP,” and press ENTER.
3 Select “Basic,” and press ENTER.
The options for “Basic” appear. The
default settings are underlined.
To turn off the display, press SYSTEM
MENU repeatedly.
Select the item you want to change using
</,, and change the settings using M/
m and press ENTER.
4
To preset another programme position,
repeat from step 2.
System
Channel Setting
Select an available TV system (page 83).
Presets programme positions manually.
If some programme positions could not be set
using the “Easy Setup” function, you can set
them manually.
BG
Select this when in West
European countries, except
those listed in “Receivable
channels” on page 83.
If there is no sound or if the picture is
distorted, the wrong tuner system may have
been preset during “Easy Setup.” Set the
correct tuner system manually in the steps
below.
DK
I
Select this when in East
European countries.
Select this when in Great
Britain/Ireland.
L*
Select this when in France.
* “L” is only available with French RDR-HX520
and RDR-HX920 models.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Channel
AFT
Press M/m repeatedly until the programme
position you want is displayed.
The programme positions are scanned in the
order shown in the table below.
Select “On” to turn on AFT.
On
Turns on the Auto Fine
Tuning function.
Normally, select this.
• If you know the number of the programme
position you want, press the number
buttons. For example, for programme
position 5, first press “0” and then press
“5.”
• To disable a programme position, enter
“00.” The disabled programme positions
will be skipped when you press PROG +/–.
• To select a cable or satellite programme
position, press M/m until the programme
position you want is displayed.
Off
Allows you to adjust the
pictures manually.
• If the Auto Fine Tuning function does not
work effectively, select “Off” and press ,.
Press M/m to obtain a clearer picture, and
press <.
Receivable channels
TV system
Channel coverage
Name
BG (West European E2 – E12 VHF
Changes or enters a new station name (up to
5 characters). The recorder must receive
programme position information (for
instance, SMARTLINK information) for
station names to appear automatically.
Countries, except
Italia A – H VHF
those listed below)
E21 – E69 UHF
S1 – S20 CATV
S21 – S41 HYPER
S01 – S05 CATV
DK (East European R1 – R12 VHF
Countries)
R21 – R69 UHF
S1 – S20 CATV
S21 – S41 HYPER
S01 – S05 CATV
I (Great Britain/
Ireland)
Ireland A – J VHF
PAY-TV/ CANAL+
Sets the PAY-TV/Canal Plus channels.
South Africa 4 – 13
VHF
B21 – B69 UHF
S1 – S20 CATV
S21 – S41 HYPER
S01 – S05 CATV
F2 – F10 VHF
Audio
Select “NICAM” or “Standard.”
NICAM
Normally, select this.
Standard
Select this if the sound from
NICAM broadcasts is not
clear.
L* (France)
F21 – F69 UHF
B – Q CATV
S21 – S41 HYPER
* “L” is only available with French RDR-HX520
and RDR-HX920 models. To receive broadcasts
in France, select “L.”
,continued
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuning the French CATV channels
This recorder can scan the CATV channels B
to Q and the HYPER frequency channels S21
to S41. On the Channel Set menu, the
channels are indicated as S1 to S44. For
example, channel B is indicated by Channel
Set number S1, and channel Q is indicated by
Channel Set number S23 (see the table
below). If the CATV channel you want to
preset is indicated by its frequency (for
example, 152.75 MHz), refer to the table
below to find the corresponding channel
number.
Corre-
sponding
channel
Channel
Set
number
Receivable
Frequency
range (MHz)
S25
S26
S27
S28
S29
S30
S31
S32
S33
S34
S35
S36
S37
S38
S39
S40
S41
S28
S29
S30
S31
S32
S33
S34
S35
S36
S37
S38
S39
S40
S41
S42
S43
S44
331.25–339.25
339.25–347.25
347.25–355.25
355.25–363.25
363.25–371.25
371.25–379.25
379.25–387.25
387.25–395.25
395.25–403.25
403.25–411.25
411.25–419.25
419.25–427.25
427.25–435.25
435.25–443.25
443.25–451.25
451.25–459.25
459.25–467.25
Corre-
sponding
channel
Channel
Set
number
Receivable
Frequency
range (MHz)
B
C
S1
S2
116.75–124.75
124.75–132.75
132.75–140.75
140.75–148.75
148.75–156.75
156.75–164.75
164.75–172.75
172.75–180.75
180.75–188.75
188.75–196.75
196.75–204.75
204.75–212.75
212.75–220.75
220.75–228.75
228.75–236.75
236.75–244.75
244.75–252.75
252.75–260.75
260.75–268.75
268.75–276.75
276.75–284.75
284.75–292.75
292.75–300.75
299.25–307.25
307.25–315.25
315.25–323.25
323.25–331.25
D
D
E
S3
S4
S5
F
S6
F
S7
G
H
H
I
S8
S9
Channel Sort
S10
S11
S12
S13
S14
S15
S16
S17
S18
S19
S20
S21
S22
S23
S24
S25
S26
S27
After the programme positions have been set,
you can change the order of each programme
position in the display list.
J
J
1
Select “Channel Sort” in “Basic,” and
press ENTER.
K
L
L
M
N
N
O
P
2
Press M/m to select the row containing
the programme position you want to
move, and press ENTER.
• To display other pages for programme
positions 4 to 99, press M/m repeatedly.
P
Q
S21
S22
S23
S24
84
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Press M/m until the selected programme
position row moves to the desired
programme position.
The selected programme position is
inserted at the new programme position.
2
Select the programme position for which
you want to set or change the TV guide
page using PROG +/– or number buttons.
• The TV guide page numbers (Example:
P301) appear automatically when the
recorder detects them.
4
5
Press ENTER to confirm the setting.
• If no page numbers are detected (P000),
you have to set the appropriate TV
guide page number manually.
To change the programme position of
another station, repeat from step 2.
Auto ProgrammeTitle Labelling
(TV Guide Page)
Some broadcast systems provide a Teletext
service* in which complete programmes and
their data (title, date, programme position,
recording start time, etc.) are stored day by
day. A TV guide page corresponds to each
day of the week. When recording a
3
Select the TV guide page number you
want to modify, and press ENTER.
programme, the recorder automatically takes
the programme name from the Teletext pages
and stores it as the title name. The TV guide
page numbers depend entirely on the
broadcast itself and may be subject to change.
If so, you may have to set those TV guide
page numbers manually in the TV Guide
Page menu.
4
5
Press the number buttons or </M/m/,
to enter the TV guide page number, and
press ENTER to confirm the setting.
• If you make a mistake, re-enter the
correct number.
* Not available in some areas.
1
Select “TV Guide Page” in “Basic,” and
press ENTER.
The TV Guide Page menu appears.
• To return to the original settings, press
O RETURN.
To set or change another TV guide page
number, repeat steps 3 and 4 above.
z Hint
To view Teletext information on your TV screen
during a broadcast, switch to your TV’s tuner by
pressing TV/DVD.
,continued
85
Download from Www.Somanuals.com. All Manuals Search And Download.
b Notes
z Hint
• In step 4 above, enter “000” if you do not want to
use the TV guide page number for automatic
labelling. The recorder will instead store a default
title name (programme position, start time - stop
time).
If you set “Auto Adjust” to “On,” the Auto Clock
Set function is activated whenever the recorder is
turned off.
b Note
• Refer to the Teletext information on your TV
screen to obtain the TV guide page number with
programme titles and their start times.
The Auto Clock Set function does not work while
the recorder is standing by for Synchro-Recording.
• If the Teletext TV guide has a page which always
shows the programmes for the current day, this
page should be input for all days.
To set the clock manually
If the Auto Clock Set function did not set the
clock correctly for your local area, try another
station for the Auto Clock Set function or set
the clock manually.
• If you start recording more than three minutes
before the programme is scheduled to start, the
correct label information may not be transferred.
• Note that this function may not work correctly
with programmes broadcast from some stations.
• If the broadcast system updates the Teletext
information at the moment recording starts, the
title label may not correspond to the recorded
programme. In this case, you may have to
1
2
Select “Clock” in “Basic,” and press
ENTER.
Select “Auto Adjust,” and press ENTER.
Clock
3
4
Select “Off,” and press ENTER.
Select “Present Time,” and press
ENTER.
Auto Adjust (Auto Clock Set)
Turns on the Auto Clock Set function when a
programme position in your local area
broadcasts a time signal.
1
Select “Clock” in “Basic,” and press
ENTER.
2
Select “Auto Adjust,” and press ENTER.
5
6
Press M/m to set the day, and press ,.
Set the month, year, hour, and minutes in
sequence. Press </, to select the item
to be set, then press M/m to set the
numbers. The day of the week is set
automatically.
3
4
Select “On,” and press ,.
Press M/m repeatedly until the
programme position of the station that
carries a time signal appears, and press
ENTER.
To change the numbers, press < to
return to the item to be changed, and
press M/m.
Press ENTER to start the clock.
• If the recorder does not receive a time
signal from any station, “Auto Adjust”
returns to “Off” automatically and the
menu for setting the clock manually
appears on the screen.
OSD (On-Screen Display)
Switches the display language on the screen.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
16:9
Video Settings (Video)
Video settings will adjust items related to the
image, such as size and colour.
Choose the settings according to the type of
TV, tuner, or decoder connected to the DVD
recorder.
4:3 Letter Box
4:3 Pan Scan
1 Press SYSTEM MENU while the
recorder is in stop mode.
2 Select “SETUP,” and press ENTER.
b Note
3 Select “Video,” and press ENTER.
The “Video” setup appears with the
following options. The default settings
are underlined.
Depending on the disc, “4:3 Letter Box” may be
selected automatically instead of “4:3 Pan Scan” or
vice versa.
Component Out
Selects whether or not to output video signals
from the COMPONENT VIDEO OUT jacks.
On
Outputs the component video
signals. Select this when you
want to view progressive
signals.
Off
Outputs no signals.
Video Output
b Notes
• When you set “Line1 Output” to “RGB,” you
cannot set “Component Out” to “On.”
TV Type
Sets the picture size when playing back a title
16:9 size commercial DVD video.
Select the playback picture size according to
the type of connected TV (wide-screen/wide
mode TV or conventional 4:3 screen TV).
• When you connect the recorder to a monitor or
projector via only the COMPONENT VIDEO
OUT jacks, do not select “Off.” If you select
“Off” in this case, the picture may not appear.
Progressive Output
If your TV accepts progressive (525p/625p)
format signals, set “Progressive Output” to
“On.” You will enjoy accurate colour
reproduction and high quality images.
16:9
Select this when connecting
to a wide-screen TV or TV
with a wide mode function.
1
2
3
Select “Progressive Output,” and press
ENTER.
4:3 Letter
Box
Select this when connecting
to a 4:3 screen TV. Displays a
wide picture with bands on
the upper and lower portions
of the screen.
Select “On,” and press ENTER.
The display asks for confirmation.
Select “Start,” and press ENTER.
The video switches to a progressive
signal for 5 seconds.
4:3 Pan
Scan
Select this when connecting
to a 4:3 screen TV.
Automatically displays a
wide picture on the entire
screen and cuts off the
portions that do not fit.
4
If video signal appears OK, select “Yes,”
and press ENTER.
If picture is distorted, select “No,” and
press ENTER.
,continued
87
Download from Www.Somanuals.com. All Manuals Search And Download.
b Notes
Progressive Mode
• If your TV does not accept S-video or RGB
signals, no picture appears on the TV screen even
if you select “S Video” or “RGB.” See the
instructions supplied with your TV.
• You cannot select “RGB” when “Component
Out” above is set to “On.”
DVD software can be divided into two types:
film based software and video based
software. Video based software is derived
from TV and displays images at 25 frames/50
fields (30 frames/60 fields) per second. Film
based software is derived from film and
displays images at 24 frames per second.
Some DVD software contains both Video
and Film.
In order for these images to appear natural on
your screen when output in progressive mode
(50 or 60 frames per second), the progressive
video signal needs to be converted to match
the type of DVD software that you are
watching.
• SMARTLINK is available only when “Video” is
selected.
Line3 Input
Selects a method of inputting video signals
for the LINE 3/DECODER jack. The picture
will not be clear if this setting does not match
the type of video input signal.
Video/
RGB
Inputs video signals or RGB
signals.
You can fine-tune the progressive 525p/625p
video signal that is output when you set
“Progressive Output” to “On.”
Note that you must connect to a progressive
format TV using the COMPONENT VIDEO
Decoder
Select this when connecting
to a PAY-TV/Canal Plus
analogue decoder. If you
connect to a cable box/
satellite receiver such as
CanalSat, do not select this
option.
Auto
Automatically detects the
software type (Film-based or
Video-based) and selects the
appropriateconversionmode.
Normally select this position.
S Video
Inputs S-video signals.
b Note
RGB signals cannot be recorded when “Video/
RGB” is selected (only French RDR-HX520 and
RDR-HX920 models can record in video or RGB).
Video
Fixes the conversion mode to
the mode for Video-based
software.
Line3 Output
Selects a method of outputting video signals
for the LINE 3/DECODER jack.
b Note
When picture noise appears after you set the
recorder to progressive format, hold down x, and
press PROGRAM – (minus) on the unit.
Video
Outputs video signals.
S Video
Outputs S-video signals.
Scart Setting
Sets the method of inputting/outputting
signals from the SCART jacks on the rear
panel of the recorder. Select an option for
each of the items below according to the
combination of jacks and methods that you
are going to use.
Pause Mode (HDD/DVDs only)
Selects the picture quality in pause mode.
Auto
The picture, including
subjects that move
dynamically, is output with
no jitter. Normally select this
position.
Line1 Output
Selects a method of outputting video signals
for the LINE 1 – TV jack.
Frame
The picture, including
subjects that do not move
dynamically, is output in high
resolution.
RGB
Outputs RGB signals.
Outputs video signals.
Outputs S-video signals.
Video
S Video
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Colour System
Selects the colour system when playing
VIDEO CDs (including Super VIDEO CDs).
Audio Settings (Audio)
The “Audio” setup allows you to adjust the
sound according to the playback and
connection conditions.
PAL
Plays a disc in PAL colour
system.
NTSC
Plays a disc in NTSC colour
system.
1 Press SYSTEM MENU while the
recorder is in stop mode.
Auto Display
2 Select “SETUP,” and press ENTER.
On
Automatically displays
information on the screen
when the recorder is turned
on, etc.
3 Select “Audio,” and press ENTER.
The “Audio” setup appears with the
following options. The default settings
are underlined.
Off
Displays information only
when DISPLAY is pressed.
Screen Saver
The screen saver image appears when you do
not use the recorder for more than 10 minutes
while an on-screen display, such as the
System Menu, is displayed on your TV
screen. The screen saver image helps prevent
your display device from becoming damaged
(ghosting).
Audio ATT (attenuation)
On
Turns on the screen saver
function.
If the playback sound is distorted, set this
item to “On.” The recorder reduces the audio
output level.
Off
Turns off the function.
This function affects the output of the
following jacks:
– LINE 2 OUT R-AUDIO-L jacks
– LINE 1 – TV jack
– LINE 3/DECODER jack
On
Select this when the playback
sound from the speakers is
distorted.
Off
Normally select this position.
,continued
89
Download from Www.Somanuals.com. All Manuals Search And Download.
• MPEG (DVD VIDEOs only)
Selects the type of MPEG audio signal.
Audio Connection
The following setup items switch the method
of outputting audio signals when you connect
a component such as an amplifier (receiver)
with a digital input jack.
For connection details, see “Step 3:
Select “Dolby Digital,” “MPEG,” “DTS,”
and “48kHz/96kHz PCM” after setting
“Digital Out” to “On.”
PCM
Select this when the recorder
is connected to an audio
component without a built-in
MPEG decoder. If you play
MPEG audio sound tracks,
the recorder outputs stereo
signals via the DIGITAL
OUT (COAXIAL) jack.
MPEG
Select this when the recorder
is connected to an audio
component with a built-in
MPEG decoder.
If you connect a component that does not
accept the selected audio signal, a loud noise
(or no sound) will come out from the
speakers, and may affect your ears or cause
speaker damage.
• DTS (DVD VIDEOs only)
1
Select “Audio Connection” in “Audio,”
and press ENTER.
Selects whether or not to output DTS signals.
On
Select this when the recorder
is connected to an audio
component with a built-in
DTS decoder.
Off
Select this when the recorder
is connected to an audio
component without a built-in
DTS decoder.
2
Select “Digital Out,” and press ENTER.
• 48kHz/96kHz PCM (DVD VIDEOs only)
Selects the sampling frequency of the audio
signal.
On
Normally select this
position.
Off
The influence of the
digital circuit upon the
analogue circuit is
minimal.
48kHz/
16bit
The audio signals of DVD
VIDEOs are converted to 48
kHz/16 bit and output.
96kHz/
24bit
All signals containing
96 kHz/24 bit are output
without conversion.
However, the signals are
output at 48 kHz/16 bit if
copyright-protected signals
are contained.
3
4
Select “On,” and press ENTER.
Set the digital output signal.
• Dolby Digital (HDD/DVDs only)
Selects the type of Dolby Digital signal.
D-PCM
Select this when the recorder
is connected to an audio
component lacking a built-in
Dolby Digital decoder. The
surround effects of output
signals are determined by the
“Downmix” setting item in
the “Audio” setup.
b Note
“48kHz/96kHz PCM” setting has no effect when
audio signals are output from the LINE 2 OUT (R-
AUDIO-L) jacks or LINE 1 – TV/LINE 3/
DECODER jack. If the sampling frequency is
96kHz, signals are simply converted to analogue
signals and output.
Dolby
Digital
Select this when the recorder
is connected to an audio
component with a built-in
Dolby Digital decoder.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio DRC (Dynamic Range Control)
(DVDs only)
Selects the dynamic range (difference
between soft and loud sounds) setting when
playing a DVD that conforms to Audio DRC.
This affects the output from the following
jacks:
Recording Settings
(Recording)
The “Recording” setup allows you to adjust
recording settings.
– LINE 2 OUT R-AUDIO-L jacks
– LINE 1 – TV jack
– LINE 3/DECODER jack
1 Press SYSTEM MENU while the
recorder is in stop mode.
– DIGITAL OUT (COAXIAL) jack only
when “Dolby Digital” is set to “D-PCM”
(page 90).
2 Select “SETUP,” and press ENTER.
3 Select “Recording,” and press
Standard
TV Mode
Normally select this position.
ENTER.
Makes low sounds clear even
if you turn the volume down.
The “Recording” setup appears with the
following options. The default settings
are underlined.
Wide
Gives you the feeling of
Range
being at a live performance.
Downmix (DVDs only)
Switches the method for mixing down to two
channels when you play a DVD which has
rear sound elements (channels) or is recorded
in Dolby Digital format. For details on the
rear signal components, see “4. Displaying
Information” on page 31. This function
affects the output of the following jacks:
– LINE 2 OUT R-AUDIO-L jacks
– LINE 1 – TV jack
HDD Rec. Settings
Bilingual Recording
Selects the sound to be recorded on the HDD.
– LINE 3/DECODER jack
Main
Sub
Records the main sound for
the bilingual programme.
– DIGITAL OUT (COAXIAL) jack when
“Dolby Digital” is set to “D-PCM”
(page 90).
Records the sub sound for the
bilingual programme.
Dolby
Normally select this position.
Multi-channel audio signals
are output to two channels for
enjoying surround sounds.
Surround
Main+Sub Records the main and sub
sounds for the bilingual
programme.
Normal
Multi-channel audio signals
are downmixed to two
channels for use with your
stereo.
b Note
If you change the recording mode while dubbing
from a DVD to the HDD, the sound recorded in the
source (DVD) is applied regardless of this setting.
,continued
91
Download from Www.Somanuals.com. All Manuals Search And Download.
HQ Setting
Selects the HQ mode used for recording on
Synchro Rec
Selects the recording destination used for
HQ+
Records in higher quality
(approximate 15 Mbps).
Recordto
HDD
Records to the HDD.
HQ
Records in the standard HQ
mode.
Recordto
DVD
Records to DVDs.
DVD Rec. Settings
Auto Chapter
Selects whether to automatically divide a
recording (a title) into chapters during
recording or dubbing.
Bilingual Recording (for all recordable
discs except DVD-RWs/DVD-Rs in VR mode)
Selects the sound to be recorded on the
recordable disc. This setting is not necessary
when recording on DVD-RWs/DVD-Rs (VR
mode) that record both the main and sub
sounds.
On
Inserts chapter marks at
approximately 6 minute
intervals.
Off
No chapter mark is inserted.
Main
Records the main sound for
the bilingual programme.
b Notes
• The actual chapter mark interval may vary
depending on the amount of information
contained in the video to be recorded.
Sub
Records the sub sound for the
bilingual programme.
• Chapter marks are automatically inserted where
the recordings start on the tape when “Auto
Chapter” is set to “On” during DV dubbing to the
HDD or a DVD-RW/DVD-R (VR mode).
Timer Settings
Rec Mode Adjust
On
Automatically adjusts the
recording mode to enable the
entire programme to be
recorded (page 43).
Off
Turns off the function.
Auto Title Erase (HDD only)
On
Automatically erases old
titles recorded on the HDD
Off
Turns off the function.
TV Direct Rec (HDD/DVD+RW/DVD-RW/
DVD+R/DVD-R only)
On
Allows you to easily record
what you are watching on the
TV using SMARTLINK.
Off
Turns off the TV Direct Rec
function.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
• When you have already registered a
password, the display for entering the
password appears.
Disc Settings (DVD)
The “DVD” setup allows you to adjust
parental control, language and other DVD
related settings.
1 Press SYSTEM MENU while the
recorder is in stop mode.
2
3
4
Enter your four-digit password using the
number buttons, then select “OK” and
press ENTER.
2 Select “SETUP,” and press ENTER.
3 Select “DVD,” and press ENTER.
The “DVD” setup appears with the
following options. The default settings
are underlined.
Select “Standard,” and press ENTER.
The selection items for “Standard” are
displayed.
Parental Control (DVD VIDEO only)
Playback of some DVD VIDEOs can be
limited according to a predetermined level,
such as the age of the users. Scenes may be
blocked or replaced with different scenes.
1
Select “Parental Control” in “DVD,” and
press ENTER.
Select a geographic area as the playback
limitation level, and press ENTER.
The area is selected.
• When you select “Others,” press the
number buttons to select and enter an
select “OK” and press ENTER.
• If you have not entered a password, the
display for registering a new password
appears.
,continued
93
Download from Www.Somanuals.com. All Manuals Search And Download.
z Hint
5
Select “Level,” and press ENTER.
The selection items for “Level” are
displayed.
If you select “Others” in “DVD Menu,” “Subtitle,”
or “Audio,” select and enter a language code from
“Language Code List” on page 111 using the
number buttons.
b Note
If you select a language in “DVD Menu,”
“Subtitle,” or “Audio” that is not recorded on the
DVD VIDEO, one of the recorded languages will
be automatically selected.
The lower the value, the stricter the
limitation.
Discs rated higher than the selected level
will be restricted.
Format DVD-RW (DVD-RW only)
The recorder automatically starts formatting
in VR mode or Video mode, whichever is
selected below, when a new, unformatted
DVD-RW is inserted.
6
Select the level, and press ENTER.
The Parental Control setting is complete.
VR
Automatically formats the
disc in VR mode.
To cancel the Parental Control setting for
the disc, set “Level” to “Off” in step 6.
To change the password, select
Video
Automatically formats the
disc in Video mode.
“Password” in step 3, and press ENTER.
When the display for registering a
password appears, enter a new four-digit
password using the number buttons, then
select “OK” and press ENTER.
One Touch Dubbing
Displays the following options for the One
Touch Dub function.
Finalise Disc (for all recordable discs
except DVD-RW in VR mode)
Selects whether or not to finalise the disc
automatically following One Touch Dubbing
b Notes
• If you forget your password, you will have to
reset it by selecting “Parental Control” of
“Factory Setup” in the “Others” setup (page 95).
• When you play discs which do not have the
Parental Control function, playback cannot be
limited on this recorder.
Auto
Automatically finalises the
disc following One Touch
Dubbing.
• Depending on the disc, you may be asked to
change the Parental Control level while playing
the disc. In this case, enter your password, then
change the level.
Manual
Allows you to finalise the
disc manually.
Language (DVD VIDEO only)
DVD Menu
Switches the language for the DVD menu.
Audio
Switches the language of the sound track.
When you select “Original,” the language
given priority in the disc is selected.
Subtitle
Switches the language of the subtitles
recorded on the disc.
When you select “Audio Follow,” the subtitle
language changes according to the language
you selected for the sound track.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Factory Setup
Allows you to select the setup settings by
group, and return them to their default
settings. Note that all of your previous
settings will be lost.
Remote Control Settings/
Factory Settings (Others)
The “Others” setup allows you to set up other
operational settings.
1
Select “Factory Setup” in “Others,” and
press , or ENTER.
The display for selecting a group of
settings appears.
1 Press SYSTEM MENU while the
recorder is in stop mode.
2
Select the group of settings you want to
return to default from “Basic,” “Video,”
“Audio,” “Recording,” “DVD,”
“Others,” “Parental Control,” and “All,”
and press , or ENTER.
2 Select “SETUP,” and press ENTER.
3 Select “Others,” and press ENTER.
The “Others” setup appears with the
following options. The default settings
are underlined.
3
4
Select “Start,” and press ENTER.
The selected settings return to their
default settings.
Press ENTER when “Finish” appears.
Format
You can erase all titles recorded on the HDD.
Dimmer
Adjusts the lighting of the front panel display.
Normal
Bright lighting.
Save
Power
Low lighting. Turns off the
lighting when the power is
off.
Command Mode
Changes the Command Mode of the recorder
if other DVD equipment is assigned the same
Command Mode. For details, see “If you
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Easy Setup
(Resetting the Recorder)
Select this to run the “Easy Setup”
programme.
1 Press SYSTEM MENU while the
recorder is in stop mode.
2 Select “SETUP,” and press ENTER.
3 Select “Easy Setup,” and press
ENTER.
4 Select “Start.”
5 Follow the instructions for “Easy
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture noise appears.
, If the picture output signal from your
recorder passes through your VCR to get to
your TV, or if you are connected to a
combination TV/VIDEO player, the copy-
protection signal applied to some DVD
programmes could affect picture quality. If
you still experience this problem even when
you connect your recorder directly to your
TV, try connecting your recorder to your
TV’s S VIDEO input.
, You have set the recorder to progressive
format even though your TV cannot accept
the progressive signal. In this case, hold
down x, and press PROGRAM – (minus)
on the unit.
Additional Information
Troubleshooting
If you experience any of the following
difficulties while using the recorder, use this
troubleshooting guide to help remedy the
problem before requesting repairs. Should
any problem persist, consult your nearest
Sony dealer.
Power
, Even if your TV is compatible with
progressive format (525p/625p) signals, the
image may be affected when you set the
recorder to progressive format. In this case,
hold down x, and press PROGRAM –
(minus) on the unit and the recorder is set to
normal (interlace) format.
The power does not turn on.
, Check that the mains lead is connected
securely.
Picture
, You are playing a DVD recorded in a colour
system that is different from your TV.
, Noise may appear in the pictures recorded
on the HDD, which is due to the
characteristics of HDD, and is not a
malfunction.
, When playing a double-layer DVD, the
video and audio may be momentarily
interrupted at the point where the layers
switch.
There is no picture.
, Re-connect all connecting cords securely.
, The connecting cords are damaged.
, Switch the input selector on your TV (such
as to “VCR”) so that the signal from the
recorder appears on the TV screen.
, Check that “Scart Setting” in the “Video”
setup is set to the appropriate item that
, If you connect the recorder to your TV via
only the COMPONENT VIDEO OUT
jacks, set “Component Out” in the “Video”
, This recorder cannot record NTSC signals.
, When playing a double-layer DVD, the
video and audio may be momentarily
interrupted at the point where the layers
switch.
There is no picture or the picture noise
appears when connected to the DV IN
jack.
, Try the following:
1Turn the recorder off and on again.
2Turn the connected equipment off and on
again. 3Disconnect and then connect the
i.LINK cable again.
TV programme reception does not fill the
screen.
, Set the channel manually in “Channel
, Select the correct source using the INPUT
SELECT button, or select a channel of any
TV programme using the PROG +/–
buttons.
,continued
97
Download from Www.Somanuals.com. All Manuals Search And Download.
TV programme pictures are distorted.
, Reorient the TV aerial.
, Adjust the picture (see the TV’s instruction
manual).
The picture does not fill the screen.
, Set “TV Type” of the “Video Output” in the
“Video” setup in accordance with the
, Place the recorder and TV farther apart.
, Place the TV and any bunched aerial cables
farther apart.
, The aerial cable is connected to the
AERIAL OUT jack on the recorder.
Connect the cable to the AERIAL IN jack.
The picture does not fill the screen, even
though the picture size is set in “TV Type”
of the “Video Output” in the “Video”
setup.
, The picture size of the title is fixed.
TV channels cannot be changed.
, A timer recording started, which changed
the channels.
The picture is black and white.
, Check that “Line1 Output” of the “Scart
Setting” in the “Video” setup is set to the
appropriate item that conforms to your
system (page 88).
The picture from equipment connected to
the recorder’s input jack does not appear
on the screen.
, If you are using a SCART cord, be sure to
use one that is fully wired (21 pins).
, If the equipment is connected to the LINE 1
– TV jack, select “L1” in the front panel
display by pressing PROG +/– or INPUT
SELECT.
Sound
There is no sound.
If the equipment is connected to the LINE 2
IN jacks, select “L2” in the front panel
display by pressing PROG +/– or INPUT
SELECT.
If the equipment is connected to the LINE
3/DECODER jack, select “L3” in the front
panel display by pressing PROG +/– or
INPUT SELECT.
If the equipment is connected to the DV IN
jack, (this is usually for a digital video
camera connection), select “DV” in the
front panel display by pressing INPUT
SELECT.
, Re-connect all connections securely.
, The connecting cord is damaged.
, The input source setting on the amplifier or
the connection to the amplifier is incorrect.
, The recorder is in reverse play, fast-
forward, slow motion, or pause mode.
, If the audio signal does not come through
the DIGITAL OUT (COAXIAL) jack,
check the “Audio Connection” settings in
the “Audio” setup (page 89).
Sound distortion occurs.
, Set “Audio ATT” in the “Audio” setup to
The playback picture or TV programme
from the equipment connected through the
recorder is distorted.
, If the playback picture output from a DVD
player, VCR, or tuner goes through your
recorder before reaching your TV, the copy-
protection signal applied to some
Sound is noisy.
, When playing a CD with DTS sound tracks,
noise will come from the LINE 2 OUT R-
AUDIO-L jacks, LINE 1 – TV jack, or
programmes could affect picture quality.
Disconnect the playback equipment in
question and connect it directly to your TV.
The sound volume is low.
, The sound volume is low on some DVDs.
The sound volume may improve if you set
“Audio DRC” in the “Audio” setup to “TV
Mode” (page 91).
, Set “Audio ATT” in the “Audio” setup to
98
Download from Www.Somanuals.com. All Manuals Search And Download.
An alternate audio track cannot be
recorded or played.
The recorder starts playing automatically.
, The DVD VIDEO features an auto
playback function.
, When recording from connected
equipment, set “Line Audio Input” in
, Multilingual tracks (main and sub) cannot
be recorded on DVD+RWs, DVD-RWs
(Video mode), DVD+Rs, or DVD-Rs
(Video mode). To record the language, set
“Bilingual Recording” of the “DVD Rec.
Settings” in the “Recording” setup to
“Main” or “Sub” before recording
(page 92). To record both the main and sub
sounds, record on DVD-RWs/DVD-Rs
(VR mode).
, Any discs other than the HDD or DVD-
RWs/DVD-Rs (VR mode) cannot be used
for recording both main and sub sounds. To
record on the HDD, set “Bilingual
Recording” of the “HDD Rec. Settings” in
the “Recording” setup to “Main+Sub”
Playback stops automatically.
, If the DVD has an auto pause signal, the
recorder stops playback at the auto pause
signal.
Some functions such as Stop, Search, or
Slow-motion Play cannot be performed.
, Depending on the DVD, you may not be
able to do some of the operations above. See
the instruction manual supplied with the
disc.
The language for the sound track cannot
be changed.
, Multilingual tracks are not recorded on the
DVD being played.
, The DVD VIDEO prohibits the changing of
the language for the sound track.
, Try changing the language using the DVD
VIDEO’s menu.
, If you have connected an AV amplifier to
the DIGITAL OUT (COAXIAL) jack and
want to change the audio track for HDD/
DVD-RWs/DVD-Rs (VR mode) during
playback, set “Dolby Digital” of the “Audio
Connection” in the “Audio” setup to “D-
The subtitle language cannot be changed
or turned off.
, Multilingual subtitles are not recorded on
the DVD VIDEO.
, The DVD VIDEO prohibits changing of the
subtitles.
Playback
, Try changing the subtitle using the DVD
VIDEO’s menu.
, The subtitles cannot be changed for the
titles recorded on this recorder.
The recorder does not play any type of disc
(except HDD).
, The disc is upside down. Insert the disc with
the labelled side facing up.
, The disc is not correctly inserted.
, Moisture has condensed inside the recorder.
In this case, if the recorder is on, leave it on
(if it is off, leave it off) for about an hour
until the moisture evaporates.
, If the disc was recorded on another recorder
recorder cannot play the disc.
The angles cannot be changed.
, Multi-angles are not recorded on the DVD
VIDEO being played.
, You are trying to change the angles when
“
” does not appear on the TV screen
, The DVD VIDEO prohibits changing
angles.
, Try changing the angle using the DVD
VIDEO’s menu.
, The angles cannot be changed for the titles
recorded on this recorder.
, The angles cannot be changed during slow
motion playback or when playback is
paused.
The recorder does not start playback from
the beginning.
, You have inserted a DVD whose Title menu
or DVD menu automatically appears on the
TV screen when it is first inserted. Use the
menu to start playback.
,continued
99
Download from Www.Somanuals.com. All Manuals Search And Download.
The MP3 audio tracks do not play.
, The MP3 audio tracks are not recorded in a
Recording does not stop immediately
after you press x REC STOP.
, It will take a few seconds for the recorder to
input disc data before recording can stop.
The JPEG image files do not play.
, The JPEG image files are not recorded in a
, Progressive JPEG images cannot be played.
Recording does not stop after you press
x.
, Press x REC STOP.
TV Pause does not work.
, You are recording to the HDD or the HDD
is full.
Timer recording is not complete or did not
start from the beginning.
, There was a power failure during recording.
If the power recovers when there is a timer
recording, the recorder resumes recording.
Should the power failure continue for more
, Other timer setting overlapped the timer
Recording/Timer recording/
Editing
The programme position cannot be
changed from the programme position you
are recording.
, Disc space was not enough.
, The PDC/VPS function is working.
, Set the TV’s input source to “TV.”
Contents previously recorded were
erased.
, Data that is not playable on this recorder but
was recorded on a DVD with a PC will be
erased from the disc when the disc is
inserted.
Recording does not start immediately
after you press z REC.
, Operate the recorder only after “LOAD,”
“FORMAT,” or “INFOWRITE” disappears
from the front panel display.
, “Auto Title Erase” of the “Timer Settings”
in the “Recording” setup is set to “On”
Nothing was recorded even though you set
the timer setting correctly.
, There was a power failure during recording.
, The recorder’s internal clock stopped due to
a power failure that lasted for more than 1
hour. Reset the clock (page 86).
, The channel was disabled after the timer
recording was set. See “Channel Setting”
, Disconnect the mains lead from the mains,
and connect it again.
, “PDC/VPS Scan Off” was selected in the
The PDC/VPS function does not operate.
, Check that the clock and date are set
correctly.
, Check that the PDC/VPS time you set is the
correct one (there might be a mistake in the
TV programme guide). If the broadcast you
wanted to record did not send the good
PDC/VPS information, the recorder will not
start recording.
, If the reception is poor, the PDC/VPS signal
might be altered and the recorder might not
start recording.
, The programme contains copy protection
signals that restrict copying.
, Other timer setting overlapped the timer
setting (page 48).
, There is no DVD inside the recorder.
, There is not enough disc space for the
recording.
, The recorder was in the process of dubbing
(HDDyDVD).
, The recorder was in the process of DV
Dubbing.
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording from the equipment
with a timer
Display
The clock has stopped.
, The clock stopped due to a power failure
that lasted for more than 1 hour. Reset the
clock (page 86).
Nothing was recorded even though you set
the Synchro-Rec setting correctly.
, You forgot to turn off the connected
equipment. Turn off the connected
equipment and set the recorder to Synchro-
, The recorder was not set to the Synchro-
Recording standby mode. Press
The TIMER REC indicator is flashing.
, The disc does not have enough space.
, Insert a recordable disc inside the recorder.
c z SYNCHRO REC to have the recorder
stand by for recording. Make sure the
SYNCHRO REC indicator lights up on the
The recording mode indication is
incorrect.
, The equipment is not connected to the LINE
3/DECODER jack of the recorder.
, The recorder is connected to the TV output
jack of the connected equipment.
,
When the recording or dubbing is less than
ten minutes, or if a picture with little
movement is displayed for more than ten
minutes, the recording mode indication may
be displayed incorrectly. Note that the actual
recording or dubbing itself was correctly
made in the selected recording mode.
Synchro-Recording does not complete.
, The timer setting for the connected
equipment overlapped the recorder’s timer
, There was a power failure during the
recording.
, After playing titles recorded in EP and SLP
mode, the recording mode indication may
change depending on the recorded
programme.
The clock does not appear in the front
panel display when the recorder is turned
off.
, “Dimmer” in the “Others” setup is set to
The recorder automatically starts
recording when the satellite receiver is
turned on.
, The Synchro-Rec function was activated.
Turn off the satellite receiver and cancel the
Remote control
Dubbing
The remote does not function.
, Batteries are weak.
You dubbed a title, but the title did not
appear in the HDD Title List.
, The title contained a copy protection signal,
so it was moved (page 72).
, The remote is too far from the recorder.
, The remote’s manufacturer code returned to
the default setting when you replaced the
, The remote is not pointed at the remote
sensor on the recorder.
, Different command modes are set for the
recorder and remote. Set the same
command mode setting for this recorder and
the supplied remote is DVD3.
High-speed dubbing is not possible.
, The title cannot be dubbed at high-speed
(page 71). Even if A-B erasure is performed
so that a title does not contain mixed picture
sizes, it is still treated as a title with mixed
picture sizes.
, Press x (stop) on the unit while the
recorder is turned off to check the current
command mode.
,continued
101
Download from Www.Somanuals.com. All Manuals Search And Download.
The disc tray does not open and you
cannot remove the disc after you press Z
(open/close).
, Turn off the recorder. Once the clock
appears in the front panel display,
Others
The recorder does not operate properly.
, Restart the recorder. Press down [/1 on the
recorder for more than ten seconds until
“WELCOME” appears in the front panel
display.
, When static electricity, etc., causes the
recorder to operate abnormally, turn off the
recorder and wait until the clock appears in
the front panel display. Then, unplug the
recorder and after leaving it off for a while,
plug it in again.
disconnect the mains lead. (If the recorder
does not turn off or if the clock does not
appear in the front panel display, disconnect
the mains lead anyway.) Connect the mains
lead again while pressing down A on the
recorder, and release the button when the
disc tray opens. Then, keep [/1 on the
recorder pressed for about ten seconds until
“WELCOME” appears in the front panel
display.
Five numbers or letters are displayed in
the front panel display.
, The self-diagnosis function was activated
(see the table on page 103).
“RECOVERY” appears in the front panel
display.
, The recorder’s recovery function was
activated when the recorder was turned on
because the power was turned off or failed
during recording. Leave the recorder on
until “RECOVERY” disappears from the
front panel display.
The disc tray does not open after you press
Z (open/close).
, It may take a few seconds for the disc tray
to open after you have recorded or edited a
DVD. This is because the recorder is adding
disc data to the disc.
“HDD ERROR” appears in the front panel
display.
The disc tray does not open and
“LOCKED” appears in the front panel
display.
, The disc tray is locked. Cancel the Child
, The hard disk error occurred. Press down
[/1 on the recorder for ten seconds until
“WELCOME” appears in the front panel
display. If this does not resolve the problem,
format the recorder’s HDD by pressing
down the HDD button on the recorder for
more than ten seconds until “FORMAT”
appears in the front panel display. Note that
all the contents recorded on the HDD will
be erased. If this does not fix the problem,
contact your nearest Sony dealer.
The disc tray does not open and “TRAY
LOCKED” appears in the front panel
display.
, Contact your Sony dealer or local
authorized Sony service facility.
102
Download from Www.Somanuals.com. All Manuals Search And Download.
“FAN ERROR” appears in the front panel
display.
, Check that the vent on the rear of the
recorder is not blocked. Then, immediately
disconnect the mains lead. Leave the
recorder off for a while, then re-connect the
mains lead, and press [/1 on the recorder.
Self-diagnosis Function
(When letters/numbers
appear in the display)
When the self-diagnosis function is activated
to prevent the recorder from malfunctioning,
a five-character service number (e.g., C 13
00) with a combination of a letter and four
numbers appears in the front panel display. In
this case, check the following table.
Mechanical sound is heard when the
recorder is off.
, While the recorder is adjusting the clock for
the Auto Clock Set function or scanning the
programme positions for the PDC/VPS
function, operational noises (such as the
internal fan) may be heard, even when the
power is off. This is not a malfunction.
First three
Cause and/or corrective
characters of action
the service
number
C 13
There is a problem in the
HDD.
, Contact your nearest
Sony dealer or local
authorized service
facility.
The DVD is dirty.
, Clean the disc with a soft
cloth.
C 31
E XX
The DVD/CD is not inserted
correctly.
, Re-insert the disc
correctly.
To prevent a malfunction, the
(xx is a number) recorder has performed the
self-diagnosis function.
, Contact your nearest
Sony dealer or local
authorized Sony service
facility and give the five-
character service number.
Example: E 61 10
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes about the discs
• To keep the disc clean, handle the disc by its
edge. Do not touch the surface. Dust,
fingerprints, or scratches on the disc may
cause it to malfunction.
Notes About This
Recorder
On operation
• If the recorder is brought directly from a
cold to a warm location, or is placed in a
very damp room, moisture may condense
on the lenses inside the recorder. Should
this occur, the recorder may not operate
properly. In this case, if the recorder is on,
leave it on (if it is off, leave it off) for about
an hour until the moisture evaporates.
• When you move the recorder, take out any
discs and do not apply shock or vibration to
the hard disk drive. If you don’t, the disc or
• Do not expose the disc to direct sunlight or
heat sources such as hot air ducts, or leave
it in a car parked in direct sunlight as the
temperature may rise considerably inside
the car.
• After playing, store the disc in its case.
• Clean the disc with a cleaning cloth. Wipe
the disc from the centre out.
On adjusting volume
Do not turn up the volume while listening to
a section with very low level inputs or no
audio signals. If you do, the speakers may be
damaged when a peak level section is played.
• Do not use solvents such as benzine,
thinner, commercially available cleaners, or
anti-static spray intended for vinyl LPs.
• Do not use the following discs.
– A disc that has a non-standard shape (e.g.,
card, heart).
– A disc with a label or sticker on it.
– A disc that has cellophane tape or sticker
adhesive on it.
On cleaning
Clean the cabinet, panel, and controls with a
soft cloth slightly moistened with a mild
detergent solution. Do not use any type of
abrasive pad, scouring powder or solvent
such as alcohol or benzine.
On cleaning discs, disc/lens cleaners
Do not use cleaning discs or disc/lens
cleaners (including wet or spray types).
These may cause the recorder to
malfunction.
On replacement of parts
In the event that this unit is repaired, repaired
parts may be collected for reuse or recycling
purposes.
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Inputs and outputs
LINE 2 OUT
Specifications
(AUDIO): Phono jack/2 Vrms/10 kilohms
(VIDEO): Phono jack/1.0 Vp-p
(S VIDEO): 4-pin mini DIN/Y: 1.0 Vp-p,
C: 0.3 Vp-p (PAL)
LINE 2 IN
(AUDIO): Phono jack/2 Vrms/more than
22 kilohms
(VIDEO): Phono jack/1.0 Vp-p
(S VIDEO): 4-pin mini DIN/Y: 1.0 Vp-p,
C: 0.3 Vp-p (PAL)
System
Laser: Semiconductor laser
Channel coverage:
PAL (B/G, D/K, I)
VHF: E2 to E12, R1 to R12, Italian A
to H, Ireland A to J, South Africa 4 to
13
UHF: E21 to E69, R21 to R69, B21 to
B69
LINE 1 – TV: 21-pin
CATV: S01 to S05, S1 to S20
HYPER: S21 to S41
CVBS IN/OUT
S-Video/RGB OUT (upstream)
LINE 3/DECODER: 21-pin
CVBS IN/OUT
SECAM (L) (for French RDR-HX520
and RDR-HX920 models only)
VHF: F2 to F10
UHF: F21 to F69
CATV: France B to Q
HYPER: S21 to S41
S-Video/RGB IN
(RGB signals cannot be recorded,
except with French RDR-HX520 and
RDR-HX920 models.)
S-Video OUT (downstream)
Decoder
The above channel coverage merely ensures
the channel reception within these ranges. It
does not guarantee the ability to receive
signals in all circumstances. For details, see
DV IN: 4-pin/i.LINK S100
DIGITAL OUT (COAXIAL): Phono jack/
0.5 Vp-p/75 ohms
COMPONENT VIDEO OUT
(Y, PB/CB, PR/CR):
Video reception: Frequency synthesizer
system
Audio reception: Split carrier system
Aerial out: 75-ohm asymmetrical aerial
socket
Phono jack/Y: 1.0 Vp-p,
P
B/CB: 0.7 Vp-p, PR/CR: 0.7 Vp-p
General
Power requirements: 220-240 V AC,
Timer: Clock: Quartz locked/Timer
indication: 24-hour cycle (digital)/
Power back-up duration: 1 hour
Video recording format: MPEG-2,
MPEG-1
Audio recording format/applicable
bit rate: Dolby Digital 2 ch
256 kbps/128 kbps (in EP and SLP
mode)
50/60 Hz
Power consumption:
RDR-HX520: 42 W
RDR-HX720/HX722/HX920: 44 W
Dimensions (approx.):
430 × 65 × 328 mm (width/height/
depth) incl. projecting parts
Hard disk drive capacity:
RDR-HX520: 80 GB
RDR-HX720/HX722: 160 GB
RDR-HX920: 250 GB
Mass (approx.): 4.2 kg
Operating temperature: 5ºC to 35ºC
Operating humidity: 25% to 80%
,continued
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Supplied accessories:
Mains lead (1)
About i.LINK
Aerial cable (1)
Remote commander (remote) (1)
R6 (size AA) batteries (2)
The DV IN jack on this recorder is i.LINK-
compliant for digital video cameras. This
section describes the i.LINK standard and its
features.
Specifications and design are subject to
change without notice.
What is i.LINK?
Compatible colour systems
i.LINK is a digital serial interface for
handling digital video, digital audio and other
data in two directions between equipment
having the i.LINK jack, and for controlling
other equipment.
i.LINK-compatible equipment can be
connected by a single i.LINK cable. Possible
applications are operations and data
transactions with various digital AV
equipment. When two or more i.LINK-
compatible equipment are connected to this
recorder in a daisy chain, operations and data
transactions are possible with not only the
equipment that this recorder is connected to
but also with other devices via the directly
connected equipment.
This recorder is designed to record using the
PAL colour system and play back using the
PAL or NTSC colour systems.
For French RDR-HX520 and RDR-HX920
models only
The signals of the SECAM colour system can
be received or recorded but played back in the
PAL colour system only. Recording of video
sources based on other colour systems cannot
be guaranteed.
Note, however, that the method of operation
sometimes varies according to the
characteristics and specifications of the
equipment to be connected, and that
operations and data transactions are
sometimes not possible on some connected
equipment.
b Note
Normally, only one piece of equipment can be
connected to this recorder by the i.LINK cable (DV
connecting cable). When connecting this recorder
to i.LINK-compatible equipment having two or
more i.LINK jacks (DV jacks), see the instruction
manual of the equipment to be connected.
About the name “i.LINK”
i.LINK is a more familiar term for IEEE 1394
data transport bus proposed by SONY, and is
a trademark approved by many corporations.
IEEE 1394 is an international standard
standardized by the Institute of Electrical and
Electronics Engineers.
106
Download from Www.Somanuals.com. All Manuals Search And Download.
i.LINK baud rate
i.LINK’s maximum baud rate varies
according to the equipment. Three maximum
baud rates are defined:
S100 (approx. 100 Mbps*)
S200 (approx. 200 Mbps)
S400 (approx. 400 Mbps)
The baud rate is listed under “Specifications”
in the instruction manual of each equipment.
It is also indicated near the i.LINK jack on
some equipment.
The maximum baud rate of equipment on
which it is not indicated such as this unit is
“S100.”
When units are connected to equipment
having a different maximum baud rate, the
baud rate sometimes differs from the
indicated baud rate.
* What is Mbps?
Mbps stands for megabits per second, or the
amount of data that can be sent or received in one
second. For example, a baud rate of 100 Mbps
means that 100 megabits of data can be sent in
one second.
i.LINK functions on this
recorder
For details on how to dub when this recorder
is connected to other video equipment having
DV jacks, see page 76.
The DV jack on this recorder can only input
DVC-SD signals. It cannot output signals.
The DV jack will not accept MICRO MV
signals from equipment such as a MICRO
MV digital video camera with an i.LINK
jack.
For further precautions, see the notes on
For details on precautions when connecting
this recorder, also see the instruction manuals
for the equipment to be connected.
Required i.LINK cable
Use the Sony i.LINK 4-pin-to-4-pin cable
(during DV dubbing).
i.LINK and are trademarks.
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to Parts and Controls
For more information, see the pages in parentheses.
Remote
1
4
7
2
5
8
0
3
6
9
CHAPTER MARK ERASE button
S
(instant replay)/
(instant
T
./>
(previous/next) buttons (54)
U mc
/
CM (search/slow/
freeze frame) buttons (54)
The H button has a tactile dot*.
DVD button (27)
REC MODE button (27)
The + button has a tactile dot*.
The number 5 button has a tactile dot*.
wj TV PROG (programme) +/– buttons
The + button has a tactile dot*.
The AUDIO button has a tactile dot*.
* Use the tactile dot as a reference when operating
the recorder.
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Front panel
B Front panel display (110)
DVD button/indicator (27)
L
DV IN jack (76)
The + button has a tactile dot*.
SYNCHRO REC indicator (49)
Q LINE 2 IN (S VIDEO/VIDEO/
H
(remote sensor) (17)
L(MONO) AUDIO R) jacks (22)
* Use the tactile dot as a reference when operating
the recorder.
,continued
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Front panel display
SMARTLINK
DVD NICAM
VCD TV
HDD
DVD
• Clock
A HDD/DVD indicators
• Programme position
“TV” appears in the right most two
digits.
Displays the selected media and the
playing/recording status.
B Dubbing direction indicator
G Disc type*
D Displays the following:
• Playing time/remaining time
• Current title/chapter/track/index
number
H
(angle) indicator (52)
• Recording time/recording mode
* Displays DATA CDs as “CD.”
z Hint
You can turn off the front panel display when the recorder is turned off by setting “Dimmer” to “Save
Rear panel
E COMPONENT VIDEO OUT
C LINE 2 OUT (R-AUDIO-L/VIDEO)
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Language Code List
The language spellings conform to the ISO 639: 1988 (E/F) standard.
Code Language
Code Language
Code Language
Code Language
1027 Afar
1183 Irish
1347 Maori
1507 Samoan
1508 Shona
1509 Somali
1511 Albanian
1512 Serbian
1513 Siswati
1514 Sesotho
1515 Sundanese
1516 Swedish
1517 Swahili
1521 Tamil
1028 Abkhazian
1032 Afrikaans
1039 Amharic
1044 Arabic
1045 Assamese
1051 Aymara
1052 Azerbaijani
1053 Bashkir
1057 Byelorussian
1059 Bulgarian
1060 Bihari
1061 Bislama
1066 Bengali;
Bangla
1067 Tibetan
1070 Breton
1079 Catalan
1093 Corsican
1097 Czech
1103 Welsh
1105 Danish
1109 German
1130 Bhutani
1142 Greek
1144 English
1145 Esperanto
1149 Spanish
1150 Estonian
1151 Basque
1157 Persian
1165 Finnish
1166 Fiji
1186 Scots Gaelic
1194 Galician
1196 Guarani
1203 Gujarati
1209 Hausa
1349 Macedonian
1350 Malayalam
1352 Mongolian
1353 Moldavian
1356 Marathi
1357 Malay
1358 Maltese
1363 Burmese
1365 Nauru
1217 Hindi
1226 Croatian
1229 Hungarian
1233 Armenian
1235 Interlingua
1239 Interlingue
1245 Inupiak
1248 Indonesian
1253 Icelandic
1254 Italian
1257 Hebrew
1261 Japanese
1269 Yiddish
1283 Javanese
1287 Georgian
1297 Kazakh
1298 Greenlandic
1299 Cambodian
1300 Kannada
1301 Korean
1305 Kashmiri
1307 Kurdish
1311 Kirghiz
1369 Nepali
1376 Dutch
1525 Telugu
1527 Tajik
1528 Thai
1379 Norwegian
1393 Occitan
1403 (Afan)Oromo
1408 Oriya
1417 Punjabi
1428 Polish
1435 Pashto;
Pushto
1436 Portuguese
1463 Quechua
1481 Rhaeto-
Romance
1482 Kirundi
1483 Romanian
1489 Russian
1491 Kinyarwanda
1495 Sanskrit
1498 Sindhi
1501 Sangho
1502 Serbo-
Croatian
1529 Tigrinya
1531 Turkmen
1532 Tagalog
1534 Setswana
1535 Tonga
1538 Turkish
1539 Tsonga
1540 Tatar
1543 Twi
1557 Ukrainian
1564 Urdu
1572 Uzbek
1581 Vietnamese
1587 Volap k
1613 Wolof
1632 Xhosa
1665 Yoruba
1684 Chinese
1697 Zulu
1313 Latin
1326 Lingala
1327 Laothian
1332 Lithuanian
1334 Latvian;
Lettish
1171 Faroese
1174 French
1181 Frisian
1503 Singhalese
1505 Slovak
1506 Slovenian
1345 Malagasy
1703
Not specified
Area Code
Code Area
Code Area
Code Area
Code Area
2044 Argentina
2047 Australia
2046 Austria
2057 Belgium
2070 Brazil
2079 Canada
2090 Chile
2165 Finland
2174 France
2109 Germany
2248 India
2238 Indonesia
2254 Italy
2276 Japan
2304 Korea
2363 Malaysia
2362 Mexico
2149 Spain
2376 Netherlands
2390 New Zealand
2379 Norway
2427 Pakistan
2424 Philippines
2436 Portugal
2489 Russia
2499 Sweden
2086 Switzerland
2528 Thailand
2184 United
Kingdom
2092 China
2115 Denmark
2501 Singapore
111
Download from Www.Somanuals.com. All Manuals Search And Download.
“BNR” 55
D
Index
DATA CD 10
“Decoder” 25
“Digital Out” 90
Digital video camera 76
“Dimmer” 95
C
Words in quotations appear
in the on-screen displays.
Canal Plus 24
CD 10
“Change Angle” 52
“Change Order” 68
“Channel” 83
“Channel Setting” 82
“Channel Sort” 84
CHAPTER MARK 66
CHAPTER MARK
ERASE 66
Chapter number 32
“Chapter Search” 58
Chasing Playback 57
“Check Overlap” 48
Checking/changing/
cancelling timer settings
(Timer List) 47
Numerics
“Divide” 65
“Downmix” 91
DTS 90
“48kHz/96kHz PCM” 90
A
“A-B Erase” 64
Adjusting
playback picture 55
playback sound 56
recording picture 46
Aerial 12
Dubbing
“Dub Mode” 70
High-speed Dubbing
Original Dubbing 71
Rec Mode
“AFT” 83
Album number 32
“Album Search” 58
Angle 52
Area code 111
AUDIO 54
“Audio ATT” 89
Audio cord 15
“Audio DRC” 91
“Audio Settings” 56
“Auto Adjust” 86
“Auto Chapter” 92
Auto Clock Set 86
“Auto Display” 89
“AV SYNC” 56
Child Lock 53
Conversion
Dubbing 72
“Colour System” 89
Colour systems 106
“Combine” 69
“DV Audio Input” 77
DV Dubbing 76
One Touch Dubbing
COMPONENT VIDEO
OUT 13
Program Edit 79
“DV EDIT” 79
DV IN 76
“DVD” 93
Connecting
“DVD Menu” 94
“DVD Rec. Picture Size”
“DVD Rec. Settings” 92
DVD VIDEO 10
the aerial cable 12
the audio cords 15
the video cords 13
Controlling TVs with the
remote 17
Copy control signals 41
Copy-Free 41
Copy-Never 41
Copy-Once 41
CPRM 9
“Create a Playlist” 67
Creating chapters 66
B
“Basic” 82
E
Batteries 17
DV Edit 76
Bilingual recording 41
Enter characters 34
Erase all titles 64
112
Download from Www.Somanuals.com. All Manuals Search And Download.
“Erase Titles” 64
“Extend Rec” 43
fast forward 54
fast reverse 54
M
Mains Lead 16
“Make a Playlist” 68
Manual Clock Set 86
MENU 52
freeze frame 54
instant advance 54
instant replay 54
JPEG image files 59
MP3 audio tracks 59
resume play 53
scan audio 52
F
“Factory Setup” 95
“File Search” 58
“Finalise Disc” 94
“Finalise” 37
Menu
DVD’s Menu 52
Top menu 52
“Mix” 77
Finalising 36
“FNR” 55
slow-motion play 54
Playing status bar 32
“Present Time” 86
Program Edit 79
“Progressive Mode” 88
“Progressive Output” 87
“Protect Disc” 36
“Protect” 63
“Format DVD-RW” 94
Formatting 38
Freeze Frame 54
Front panel 109
“MNR” 55
“Modify” 48
MP3 audio tracks 59
MPEG 90
N
“Name” 83
G
GB 39
Protection
disc 36
title 63
H
O
Handling discs 104
“HDD Rec. Picture Size”
Q
One Touch Menu 53
One Touch Play 53
One Touch Timer 44
“Others” 95
Quick guide to disc types 8
Quick Timer 45
”HDD Rec. Settings” 91
“HQ Setting” 92
“Hue” 55
R
Rear panel 110
REC 28
Timer recording
“Rec Mode Adjust”
“Rec Mode” 46
“Rec NR” 46
“Rec Settings” 46
“Rec Video Equalizer” 46
Recordable discs 8
I
i.LINK 106
P
Parts and controls 108
“Pause Mode” 88
PAY-TV 24
J
JPEG image files 59
L
“PAY-TV/CANAL+” 83
“PB Video Equalizer” 55
PBC 52
Labelling 35
“Language” 94
LINE 2 IN 22
PDC 43
LINE 3/DECODER 21
“Line1 Output” 88
“Line3 Input” 88
“Line3 Output” 88
Picture size 46
Play mode 32
Playable discs 10
,continued
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording 40
picture adjustment 46
Synchro Rec 49
“System” 82
V
VIDEO CD 10
Video cord 13
Video input 13
Video mode 8
“Video Output” 87
VIDEO Plus+ 44
“Video Settings” 55
VPS 43
recording format 8
while watching
another
T
Thumbnail picture 30
“Time Search” 58
TIME/TEXT 32
TIMER 42
programme 28
“Recording” 91
Recording time 40
Region code 11
Timer List 47
Timer recording
“Auto Title Erase” 43
check/change/cancel
manual setting 42
Synchro Rec 49
VIDEO Plus+ 44
“Timer Settings” 92
Title 32
VR mode 8
Remaining time 32
Z
ZWEITON 41
Resetting the recorder 96
Resume Play 53
S
S VIDEO 13
TITLE LIST 52
Sort 30
Satellite receiver 23
Scan Audio 52
“Scart Setting” 88
Scene List 67
“Screen Saver” 89
“Search” 58
Searching
Thumbnail 30
“Title Name” 63
Title number 32
“Title Search” 58
TOP MENU 52
“Track Search” 58
Troubleshooting 97
Tuner System 20
“TV Guide Page” 85
TV Pause 56
fast reverse/fast
forward 54
locatingthebeginning
of the title/
chapter/track 54
scan audio 52
search mode 58
“Set Thumbnail” 64
“Sharpness” 55
SimultaneousRecandPlay
Slow-motion play 54
SMARTLINK 14
Sort 30
TV system 82
U
“Unfinalise” 38
Unfinalising 38
“Stereo1” 77
“Stereo2” 77
SUBTITLE 54
“Subtitle” 94
Super VIDEO CD 10
114
Download from Www.Somanuals.com. All Manuals Search And Download.
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Sony Corporation Printed in Hungary
Download from Www.Somanuals.com. All Manuals Search And Download.
|