3-990-977-13 (1)
Professional Disc
Recorder
Operating Instructions
Before operating the unit, please read this manual
thoroughly and retain it for future reference.
PDW-F30
© 2006 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
If you have questions on the use of the above Power Cord/
Appliance Connector/Plug, please consult a qualified service
personnel.
Denna etikett finns på ovansidan av driftenheten.
Denne mærkat sidder på drevenhedens øverste panel.
Tämä kyltti sijaitsee ajurilaitteen yläpinnalla.
When installing the installation space must be secured in
consideration of the ventilation and service operation.
• Do not block the ventilation slots at the left side and right
side panels, and vents of fans.
• Leave a space around the unit for ventilation.
• Leave more than 10 cm of space in the rear of the unit to
secure the operation area.
Dette merket er plassert på oversiden av driverenheten.
CAUTION
The use of optical instruments with this product will increase
eye hazard.
When the unit is installed on the desk or the like, leave at least
5 cm of space in the left and right sides.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
VAROITUS!
LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ
KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA
ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1
YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.
This Professional Disc Recorder is classified as a CLASS 1
LASER PRODUCT.
VARNING
OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT ÄN I DENNA
BRUKSANVISNING SPECIFICERATS, KAN ANVÄNDAREN
UTSÄTTAS FÖR OSYNLIG LASERSTRÅLNING, SOM
ÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1.
Laser diode properties
Wave length: 403 to 410 nm
Emission duration: Continuous
Laser output power: 65 mW (max. of pulse peak), 35 mW
(max. of CW)
For the customers in the USA
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
Tekniska data för laserdiod
Våglängd: 403 till 410 nm
Emissionslängd: Kontinuerlig
Laseruteffekt: 65 mW (max. för pulstopp), 35 mW (max. för
kontinuerlig våg)
Spesifikasjoner laserdiode
Bølgelengde: 403 til 410 nm
Strålingens varighet: Kontinuerlig
Laserens effekt: 65 mW (maks stråletoppunkt), 35 mW
(maks ved kontinuerlig stråling)
Laserdiodin ominaisuudet
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority to
operate this equipment.
Aallon pituus: 403 - 410 nm
Välityksen kesto: Jatkuva
Laserlähdön teho: 65 mW (sykehuipun maks.), 35 mW
(jatkuvan aallon maks.)
All interface cables used to connect peripherals must be
shielded in order to comply with the limits for a digital device
pursuant to Subpart B of Part 15 of FCC Rules.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
For the State of California, USA only
Perchlorate Material - special handling may apply, See
www.dtsc.ca.gov/hazardouswaste/perchlorate
Perchlorate Material : Lithium battery contains perchlorate.
For customers in Canada
This Class A digital apparatus complies with Canadian ICES-
003.
This label is located on the top panel of the drive unit.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
For the customers in Europe
This product with the CE marking complies with both the EMC
Directive (89/336/EEC) and the Low Voltage Directive (73/23/
EEC) issued by the Commission of the European Community.
Compliance with these directives implies conformity to the
following European standards:
• EN60065: Product Safety
• EN55103-1: Electromagnetic Interference (Emission)
• EN55103-2: Electromagnetic Susceptibility (Immunity)
This product is intended for use in the following
Electromagnetic Environment(s):
E1 (residential), E2 (commercial and light industrial), E3
(urban outdoors) and E4 (controlled EMC environment, ex. TV
studio).
For the customers in Taiwan only
Voor de Klanten in Nederland
• Gooi de batterij niet weg maar lever deze in als
klein chemisch afval (KCA).
• Dit apparaat bevat een vast ingebouwde
batterij die niet vervangen hoeft te worden
tijdens de levensduur van het apparaat.
• Raadpleeg uw leverancier indien de batterij
toch vervangen moet worden.De batterij mag
alleen vervangen worden door vakbekwaam
servicepersoneel.
• Lever het apparaat aan het einde van de
levensduur in voor recycling, de batterij zal dan
op correcte wijze verwerkt worden.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Features............................................................................................9
Features of This Unit............................................................................. 9
Setup...............................................................................................27
5
Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Handling of Discs When Recording Does Not End Normally (Salvage
Functions) .................................................................................. 36
Playback .........................................................................................41
Quick Scene Selection (Adding Sub Clips During Recording, Playback,
or Search)................................................................................... 59
Deleting Sub Clips............................................................................... 63
6
Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Directory Structure.............................................................................. 69
Condensation....................................................................................... 93
Error Messages.................................................................................. 102
7
Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Index ............................................................................................110
8
Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
1
Chapter
Playback functions
Features
Support for multiple frame frequencies
The unit can play back five different frame frequencies:
1080/59.94i (displayed as 60I), 50i (displayed as 50I),
29.97PsF (displayed as 30P), 25PsF, and 23.98PsF. The
unit features a standard 2-3 pulldown function, and can
output 60I when playing back a disc recorded in 23.98PsF.
The PDW-F30 is a professional disc recorder supporting
HD playback and recording with Professional Disc
media.
1)
It can play back MPEG HD format and DVCAM format
data streams, and record audio and video data files sent via
its i.LINK connector or the PDBK-101 Network Board.
When you use this unit in combination with a nonlinear
HD downconvert function
An HD downconvert function enables output of SD
composite, component, and i.LINK (DV) signals even
when the playback disc is in an HD format.
2)
editing system, the FAM function enables data file
transfers between the unit and computers over the i.LINK
interface, allowing the unit to be used like an external hard
drive. Its compact design, which also permits vertical
placement, saves installation space on the desktop.
It incorporates a color LCD display, allowing you to check
video and use the menu system without connecting an
external monitor.
DVCAM upconvert function
The unit features an upconvert function, with the ability to
upconvert to HD and output HD analog component, SDI
signals when playing back DVCAM discs.
i.LINK (DV) output is also supported , allowing you to
use nonlinear editors in a standard i.LINK (DV)
environment.
1)
1) Professional Disc is a trademark of Sony Corporation.
2) FAM: File access mode
1) Input (recording) is not supported.
Recording of proxy AV data
Proxy AV data is a low-resolution (1.5 Mbps video, 64
kbps per audio channel), MPEG-4 based version of a full-
resolution data stream. XDCAM recorders and camcorders
automatically generate and record low-resolution proxy
AV data whenever they record full-resolution MPEG HD
data. Because of its small size, proxy AV data can be
transferred quickly over computer networks, easily edited
in the field with laptop computers, and readily used in a
wide variety of applications, such as content management
on small-scale servers.
Features of This Unit
The principal features of this unit are as follows.
1)
MPEG HD codec
1)
High-quality video and audio playback
The MPEG HD codec provides video compression
compliant with the MPEG-2 MP@HL standard. It enables
HD 4:2:0 digital component file recording in the 1080i
(1,080 effective scanning lines, interlaced) format
currently in use by many broadcast facilities.
Uncompressed PCM recording of 16-bit 48 kHz audio
delivers a wide dynamic range with a high signal-to-noise
ratio.
1) The supplied PDZ-1 Proxy Browsing Software can be used to create
simple EDLs (Edit Decision Lists).
Input and output interfaces
This unit supports the following interfaces.
i.LINK (AV/C): This enables output of DV-format digital
video and audio signals (4 channels).
Analog video: This enables output of HD analog
component (RGB or YPbPr) and SD composite
signals.
1) MPEG HD is a trademark of Sony Corporation.
9
Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Analog audio: This enables output of 2 channels (1/2 or 3/
IT friendly
4) of analog audio.
Computer access to files (file access mode)
Video and audio clip data are recorded as files. The FAM
function enables quick random access by computers to the
video, audio, and metadata files stored on Professional
Discs, with the ability to display thumbnail lists on the
computer screen and perform file-based reads and writes.
Input
Output
Analog video
(composite)
–
Video
1)
BNC connector,
phono jack
i.LINK (AV/C)
–
Video / audio (4
channels)
1) XDCAM allows you to record various kinds of information about the
video and audio data, such as the date of shooting, the editor, the recording
format, and comments. This data can be used in the following ways.
i.LINK 6-pin
i.LINK (TS)
PDBK-102 (option board)
•
The supplied PDZ-1 Proxy Browsing Software can add titles,
comments, and other text data to discs and clips.
Analog video
(component)
–
RGB/YPbPr/HD/VD
•
The ability to search metadata for the required audio and video scenes
brings greater efficiency to various stages of the video production
process (editing, archiving).
D-sub 15-pin
Analog audio
–
Audio (2 channels)
XLR connector ×2,
phono jack ×2
Other features
High-speed searches by the jog and shuttle dials
Like conventional VTRs, this unit features jog and shuttle
dials for searching for specific scenes within clips. The
jog/variable mode supports –1 to +2 times normal speed
searching in field units. The shuttle mode enables high-
speed searching at up to 20 times normal speed.
Convenient disc-based playback and
search functions
Thumbnail searches
An independent clip file is generated whenever recording
starts and stops. The first frame of each clip is used as the
thumbnail for that clip.
You can display a list of thumbnails on the color LCD or
an external monitor, and cue up a desired scene by
selecting the corresponding thumbnail.
Variety of remote control units
• Infrared remote commander (supplied)
• RS-232C 9-pin remote control
• RS-422A 9-pin remote control
Essence mark searches
Color LCD display
You can record essence marks at any scene during video
recording, or at the recording stop position. You can
display a list of essence mark scenes on the color LCD or
an external monitor. Essence marks can also be added after
recording with the supplied PDZ-1 Proxy Browsing
Software.
The unit is equipped with a 16:9, 3.5-inch color LCD
which allows you to check the contents of the disc and use
the menu system without connecting an external monitor.
Features of the PDBK-101/102
Option Boards
Thumbnail expansion
After selecting a clip in the thumbnail list, you can divide
the clip into 12 parts and show a list of thumbnails for the
first frame in each part. This makes it easy to find the scene
you want within the clip. This expansion can be repeated
up to 3 times (1728 divisions).
The following option boards provide expanded functions
and interfaces for the unit.
Note
Scene selection
Contact your Sony dealer for more information about
purchasing and installing option boards.
You can create and play back clip lists of selected clips
from the disc, arranged in any order. One disc can store up
to 99 clip lists. Clip lists make it simple to perform offline
editing in the field for later use with full-scale nonlinear
editing systems.
PDBK-101 Network Board (Gigabit
Ethernet)
Installation of this board provides a gigabit Ethernet
connector, which can be used to transfer disc files over
LAN networks and to record MXF (Material eXchange
Format) files from external devices to discs.
It also allows this unit to be controlled remotely by FTP
commands.
Repeat playback
You can repeatedly play back any clip or clip list. Unlike
tape, discs can return to the first frame as soon as the last
frame is played, making this function ideal for
presentations with a need for looping content.
10
Features
Download from Www.Somanuals.com. All Manuals Search And Download.
PDBK-102 MPEG-TS (Transport Stream)
Input/Output Board
Installation of this board enhances the functionality of the
standard i.LINK connector, allowing it to be used as an
1)
2)
3)
I/O interface for HDV 1080i format compatible TS
signals.
HD files recorded on the disc can be converted to TS
signals compatible with the HDV1080i format for transfer
to HDV devices and HDV editors, and TS signals from
HDV devices and HDV editors can be converted to MPEG
HD compatible files for recording by this unit.
To record MPEG HD-compatible files, you can select the
appropriate video bitrate for your application from three
video bitrate modes: 35 Mbps (HQ: high quality mode), 25
Mbps (SP: standard mode), and 18 Mbps (LP: long-play
mode). You can select 2-channel or 4-channel audio, with
the ability to record 120 minutes or more of audio. If the
audio channel modes are the same, different video bitrates
can be mixed on the same disc.
1) HDV and
are trademarks of Sony Corporation and Victor
Company of Japan, Limited.
2) HDV1080i: Refers to devices compliant with the “HDV1080i Standard”
for recording HD signals on DV tape. There are 1080 effective lines.
3) TS: MPEG-2 transport streams containing MPEG video, MPEG audio,
and control information. This is the standard interface for HDV
equipment.
11
Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Names and Functions of Parts
Front Panel
q; Disc slot and EJECT button
1 On/standby 1
EJECT
F1
switch and indicator
F2
ACCESS
F3
qa Infrared sensor
2 ACCESS indicator
VAR
MARK1
NETWORK
MENU
F4
F5
CHAPTER
EXPAND
LOCAL
REMOTE
IN
OUT
SUB
CLIP
THUMB
NAIL
SET RESET
JOG
LEVEL
PAGE DISPLAY
3 Remote control switch
4 LEVEL knob
CLIP
ESSENCE
MARK
MENU
MARK2
PREV
PLAY
NEXT
STOP
TS REC
SHUTTLE
KEY INHI
CH 1
CH 2
CH 3
CH 4
PHONES
PRESET
PB
SHIFT
TOP
END
F
REV
F
FWD
STANDBY
5 PHONES jack
6 SHIFT button
7 MENU button
qs RESET button
8 SUB CLIP/CLIP MENU button
qd SET button
9 THUMBNAIL/ESSENCE MARK button
1 Display and function menu section
3 Arrow buttons
EJECT
F1
F2
F3
F4
F5
ACCESS
VAR
MARK1
NETWORK
LOCAL
MENU
Handle
CHAPTER
IN
OUT
SUB
CLIP
THUMB
NAIL
REMOTE
LEVEL
EXPAND
SET RESET
JOG
PAGE DISPLAY
CLIP
ESSENCE
MARK
4 Shuttle/jog/
variable-speed
playback control
block
MENU
MARK2
PREV
PLAY
NEXT
STOP
TS REC
SHUTTLE
KEY INHI
CH 1
CH 2
CH 3
CH 4
PHONES
PRESET
PB
SHIFT
TOP
END
F
REV
F
FWD
STANDBY
2 Audio level adjustment section
5 Recording/playback control block
a On/standby 1 switch and indicator
When using the unit, normally leave the rear panel
POWER switch in the * (on) position, and use this switch
to switch the unit between the operating and standby states.
is in the * (on) position, this switches the unit between the
operating state (the indicator is lit green) and the standby
state (the indicator is lit red).
b ACCESS indicator
When the indicator is lit red, pressing this switch puts the
unit into the operating state. The indicator initially flashes
green and then lights green when the unit enters the
operating state.
When the indicator is lit green, pressing this switch puts
the unit into the standby state. The indicator initially
flashes green, and then lights red when the unit enters the
standby state.
This lights blue while a disc is being accessed and while a
file is open by a FAM or FTP connection. If the on/standby
switch is pressed while this indicator is lit, the unit waits
until access to the disc is completed before switching to the
standby state.
12
Names and Functions of Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
screen appears. To play back the clips in the order
they were recorded, press this button again, turning it
off. The clip list selection screen disappears.
Note
Do not turn off the POWER switch on the rear panel or
disconnect the power cord while the ACCESS indicator is
lit. Doing so can result in a loss of data on the disc.
Note
This button does not light, and pressing it has no
effect, when no clip lists are registered.
c Remote control switch
Different positions of the switch allow different
operations, as follows.
CLIP MENU button: Press this button, turning it on, to
load, save, or delete a clip list. A clip list menu
appears. To erase the clip list screen from the display,
press the button again, turning it off.
NETWORK: Enables access to the network. Operation
from the front panel of the unit is disabled during
access to a network device.
LOCAL: Enables operation from the front panel of the
unit.
REMOTE: Enables remote control of this unit from a
device connected to an external device connector on
the rear of the unit or from a remote control panel (not
supplied) connected to the unit.
For details about clip lists, see Chapter 4 “Scene
i THUMBNAIL/ESSENCE MARK button
This functions as a THUMBNAIL button when pressed
alone, and as an ESSENCE MARK button when pressed
together with the SHIFT button.
Use the setup menu item INTERFACE SELECT
>REMOTE I/F to select which of the connectors is
THUMBNAIL button: Press this button, turning it on, to
search for a frame by specifying a thumbnail (see
page 43), and to create a clip list. A thumbnail
selection screen appears on the display. To erase the
selection screen from the display, press the button
again, turning it off.
d LEVEL (audio level adjustment) knob
This adjusts the volume of the audio output from the
PHONES jack. At the same time, it also adjusts the volume
of the output from the AUDIO MONITOR connector on
the rear panel.
ESSENCE MARK button: Press this button, turning it
on, to search for a frame by specifying an essence
An essence mark selection list appears. To erase the
selection list from the display, press the button again,
turning it off.
e PHONES jack (stereo phone jack)
Connect stereo headphones with an impedance of 8 ohms
to monitor audio during recording, playback, and editing.
The monitored channel is selected by the MONI CH and
MONI SEL items on the HOME page of the function menu
j Disc slot and EJECT button
Insert discs into the disc slot. The indicator flashes in
orange, and lights in blue when the disc is completely
loaded.
Press the EJECT button to eject a disc. The indicator
flashes in blue, and goes off when the disc is completely
ejected.
f SHIFT button
When pressed together with a button having two functions,
switches between the functions of the button.
Function button names are displayed in white when the
buttons are pressed alone, and in yellow when they are
pressed together with the SHIFT button.
k Infrared sensor
This receives signals from the supplied remote
commander.
g MENU button
Use this for system menu operations. The system menu
appears in the display when this button is pressed. The
same information is also superimposed on the display of a
monitor connected to the unit.
l RESET button
Press this button to reset counters. This button is also used
to cancel setup menu settings and abandon scene selections
(thumbnail search), and to cancel other operations.
Press once more to exit the menu.
For more information about the system menu, see Chapter
m SET button
Press this button to confirm menu and scene selection
(thumbnail search) settings, and to execute operations.
h SUB CLIP/CLIP MENU button
This functions as a SUB CLIP button when pressed alone,
and as a CLIP MENU button when pressed together with
the SHIFT button.
SUB CLIP button: Press this button, turning it on, to
perform playback of a clip list. A clip list selection
For details about scene selection, see Chapter 4 “Scene
13
Names and Functions of Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Display and function menu section
1 Display
F1
F2
F3
F4
2 F1 to F5 buttons
F5
PAGE DISPLAY
3 DISPLAY/KEY INH button
4 PAGE button
q; Audio level meters
5 Monitor video display section
qa Audio format
0
0
-12
-12
-20
-20
TC MODE
6 Function
menu
qs Recording/playback format
PRESET
-30
-40
-60
-30
-40
-60
RUN MODE
REC RUN
1
2
3
4
qd Time data type
+
4CH 16 BIT
3
4
KEY INH
REC INH
REMOTE
RS422A
T C / V I T C
V I T C
MPEG HD
SP
1080
COOO1
60I
INPUT
VITC
REM:077M
DF/NDF
NDF
qf Time data display section
00:00.00:00
REPEAT
P1
qg System line number
qh Clip number
7 Operation modes
8 Remaining disc capacity
9 Reference signal
qj System frequency
qk Audio monitor channels
a Display
DISPLAY button: Each press of this button switches the
monitor video display section between its three
display sizes.
KEY INH button: Each press of this button turns key
operation inhibit mode on or off.
Normally this displays the audio level meters, timecode,
monitor pictures, and current settings. It also displays
menus and scene selection (thumbnail search) setting
screens.
b F1 to F5 (Function 1 to Function 5) buttons
These buttons are enabled when the function menu (see
page 75) is visible. Each press of a button changes the
setting of the corresponding item in the menu.
When the SUB CLIP and THUMBNAIL buttons are lit,
the F4 button functions as a CHAPTER button, and the F5
button functions as an EXPAND button.
d PAGE button
This displays the function menu, if it is not already visible.
(The most recently accessed page appears.) If the function
menu is visible, this button switches between the function
menu pages (HOME, P1).
e Monitor video display section
This displays monitor video and the system menu.
You can press the DISPLAY button to switch the display
of monitor video between three sizes. The largest size
occupies the full display screen.
c DISPLAY/KEY INH (key operation inhibit mode)
button
This functions as a DISPLAY button when pressed alone,
and as a KEY INH button when pressed together with the
SHIFT button.
14
Names and Functions of Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
1)
bits. During display of E-E video, this displays 2CH/
Note
16BIT (two channels, 16 bits) or 4CH/16BIT (four
channels, 16 bits), according to the setting of AUDIO
CONTROL >REC MODE in the setup menu (see page
84). Always displays 4CH/16BIT when the DVCAM
format is being used.
Use the largest size to display the system menu and view
superimposed information.
f Function menu
Use the PAGE button to display this menu, and to switch
between the pages (HOME, P1) of the menu. Each page
has several setting items, which correspond to the F1 to F5
buttons. Press the corresponding button to change a
setting.
1) E-E: Abbreviation of Electric to Electric. A mode in which input video and
audio signals are output after passing through electric circuits only.
l Recording/playback format
This displays the following.
During playback: Recording format of the loaded disc.
During recording/E-E screen display/FAM connection:
g Operation modes
Signal format
Compression method
(video bit rate)
This displays the current operation modes.
KEY INH (key operation inhibit mode): Key operation
inhibit mode has been turned on with the KEY INH
button.
REC INH (recording inhibit mode): Recording inhibit
mode has been turned on by setting REC INH on the
HOME page of the function menu to “ON” (see page
76), or the currently loaded disc is write protected.
a)
MPEG HD
HQ
SP
LP
–
DVCAM
a) Selected with OPERATIONAL FUNCTION >REC FORMAT in the
setup menu .
Note
m Time data type
This displays the type of the time data that appears in the
time data display section. The time data type is set with
CNTR SEL on the HOME page of the function menu (see
COUNTER: Elapsed recording/playback time
TC/VITC: Timecode
Recording inhibit mode is also turned on when the
settings of the recorded part of the currently loaded
disc do not match the current settings (number of
recording audio channels, system frequency) of the
unit.
REMOTE/interface name (remote mode): The remote
control switch is set to “REMOTE”. (The interface
name corresponds to the setting of INTERFACE
SELECT >REMOTE I/F in the setup menu (see page
85).)
UB/VIUB: User bits
When TC or UB is selected, and VITC is selected under
a VITC indicator appears, TC changes to VITC, and UB
changes to VIUB.
REPEAT (repeat mode): OPERATIONAL FUNCTION
>REPEAT MODE in the setup menu is set to “ON” .
n Time data display section
Normally this displays the time data selected with CNTR
SEL on the HOME page of the function menu (see page
75).
Messages appear here when an error occurs and when the
unit enters a different mode.
h Remaining disc capacity
This displays the remaining capacity on the currently
loaded disc.
i Reference signal
This displays the type of reference signal to which this unit
is synchronizing.
When there is no display, the unit is synchronizing to the
internal reference signal.
o System line number
This displays 1080, 525, or 625 depending on the signal
format during recording, playback, FAM connection.
INPUT: Input video
p Clip number
This displays the clip number of the clip being monitored.
j Audio level meters
These display the audio playback levels of channels 1 to 4.
If an audio level exceeds 0 dB, the red indicator bar at the
top lights.
q System frequency
This displays the system frequency being used by this unit
k Audio format
During playback, this displays the number of recording
audio channels on the disc and the number of quantization
15
Names and Functions of Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
r Audio monitor channels
This displays the audio monitor channels, as set with
MONI CH and MONI SEL on the HOME page of the
1 </IN button and ,/OUT button
MARK1
IN
OUT
When you are monitoring channels 1 and 2 (MONI CH is
set to “CH 1/2”), the display changes as follows,
depending on the setting of MONI SEL.
2 M/MARK1 button and m/MARK2 button
3 IN indicator and OUT indicator
MARK2
MONI SEL setting
MONO L (monaural L)
MONO R (monaural R)
STEREO
Display
a </IN button and ,/OUT button
1
2
1
2
When the setup or disc menu is visible, use these buttons
to change menu settings. When the THUMBNAIL button
is lit, you can use these for thumbnail selection.
1 / 2
1 + 2
MIX
An In or Out point is set when you press the SET button
with the </IN or ,/OUT button held down. The In or
Out point setting is deleted when you press the RESET
button with the </IN or ,/OUT button held down.
2 Audio level adjustment section
b M/MARK1 button and m/MARK2 button
When the setup or disc menu is visible, use these buttons
to change menu settings. When the THUMBNAIL button
is lit, you can use these for thumbnail selection.
During recording and playback, the M/MARK1 or m/
MARK2 button can be pressed with the SET button held
down to record a SHOT MARK1 or SHOT MARK2 as an
essence mark.
1 CH 1 to CH 4 knobs
2 VARIABLE switch
CH 1
CH 2
CH 3
CH 4
PRESET
PB
To delete or change essence marks, use the supplied PDZ-
1 Proxy Browsing Software.
a CH 1 to CH 4 (audio level) knobs
Depending on the setting of the VARIABLE switch, these
adjust the input audio or playback audio levels of CH 1 to
CH 4.
c IN indicator and OUT indicator
IN indicator: This lights when an In point exists. It flashes
if an attempt is made to set an In point after a recorded
Out point.
OUT indicator: This lights when an Out point exists. It
flashes if an attempt is made to set an Out point before
a recorded In point.
b VARIABLE (audio level adjustment selector)
switch
This selects whether or not the playback audio has the
levels adjusted by the CH 1 to CH 4 knobs.
PRESET: The playback audio levels are fixed at preset
values.
PB: Adjust the playback audio levels.
4 Shuttle/jog/variable-speed playback
control block
3 Arrow buttons
4 Jog/shuttle transport indicators
The four arrow buttons are also used as the MARK1
button, MARK2 button, IN button, and OUT button, as
follows.
VAR
1 VAR button
JOG
M button: MARK1 button
m button: MARK2 button
2 JOG button
< button: IN button
SHUTTLE
, button: OUT button
3 SHUTTLE
button
5 Jog dial
You can use these buttons for menu setting operations,
thumbnail selection, setting or deleting In/Out points, and
so on.
6 Shuttle dial
For details about playback operations with these buttons
16
Names and Functions of Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
a VAR (variable) button
To play back in variable-speed mode using the shuttle dial,
5 Recording/playback control block
press this button, turning it on.
1 PREV/TOP button
b JOG button
2 PLAY button
To play back in jog mode using the jog dial, press this
button, turning it on.
3 NEXT/END button
c SHUTTLE button
PREV
PLAY
NEXT
STOP
TS REC
To play back in shuttle mode using the shuttle dial, press
this button, turning it on.
TOP
END
F REV
F FWD
STANDBY
d Jog/shuttle transport indicators
These show the playback direction in jog, shuttle, or
variable-speed mode.
4 STOP/STANDBY button
5 TS REC button
b (green): Lights during playback in the reverse direction.
B (green): Lights during playback in the forward
direction.
a PREV (previous)/TOP button
This functions as a PREV button when pressed alone, and
as a TOP button when pressed together with the SHIFT
button.
PREV button: Press this button, turning it on, to jump to
the first frame of the current clip. When pressed at the
first frame of the current clip, this button jumps to the
first frame of the previous clip.
x (red): Lights during still image display.
e Jog dial
Turn this for playback in jog mode. Turn clockwise for
forward direction playback, and counterclockwise for
reverse direction playback. In jog mode, the playback
speed varies in the range 1 times normal speed, according
to the rotation rate of the jog dial. The dial has no detents.
TOP button: Press this button to jump to the first frame of
the first clip.
You can perform a high-speed search in the reverse
direction by pressing the PREV button together with the
PLAY button.
f Shuttle dial
Turn this for playback in shuttle mode or variable-speed
mode. Turn clockwise for forward direction playback, and
counterclockwise for reverse direction playback.
• In shuttle mode, the playback speed varies in the range
20 times normal speed (using MPEG HD/DVCAM),
according to the angular position of the shuttle dial.
• In variable-speed mode, you can finely adjust the
playback speed from –1 to +2 times normal speed,
according to the angular position of the shuttle dial.
The shuttle dial has a detent at the center position, for still
image playback.
b PLAY button
Press this button, turning it on, to start playback. Press the
STOP button to stop playback.
You can perform a high-speed search in the forward or
reverse direction by pressing this button together with the
NEXT button or PREV button.
c NEXT/END button
This functions as a NEXT button when pressed alone, and
as an END button when pressed together with the SHIFT
button.
Note
NEXT button: Press this button, turning it on, to jump to
the first frame of the next clip.
END button: Press this button to jump to the last frame of
the last clip.
When OPERATIONAL FUNCTION >SEARCH
ENABLE in the setup menu is set to “DIAL DIRECT” ,
return the shuttle dial to the center position after using it.
You can perform a high-speed search in the forward
direction by pressing the NEXT button together with the
PLAY button.
d STOP/STANDBY button
This functions as a STOP button when pressed alone, and
as a STANDBY button when pressed together with the
SHIFT button.
STOP button: Press this button, turning it on, to stop
recording or playback. The frame at the stop position
is displayed.
17
Names and Functions of Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
STANDBY button: Press this button to put the unit into
standby-off mode (the STOP button lights, and the
STANDBY indicator lights). Press it again to return
to the original state (STOP button lit, STANDBY
indicator off).
e TS REC (transport stream record) button
Press this button together with the PLAY button to start
recording. Recording starts on the unrecorded part of the
disc.
Press the STOP button to stop recording. A clip is created
from the recorded section.
This unit has a function that can put it into standby-off
mode automatically after a certain length of time passes in
disc stop mode. For details, see the explanation of STILL
Note
This button is enabled when you record TS input signals
(when the PDBK-102 MPEG-TS Input/Output Board is
installed) or the signals of the internal signal generator.
Rear Panel
COMPOSITE OUT
AUDIO MONITOR
-AC IN
R
L
1 Analog video signal
POWER
output section
3 Power supply
AUDIO OUTPUT
2/4
section
1/3
2 Analog audio signal
output section
MONITOR
RS232C
REMOTE(9P)
S400
4 External device connection
section
b MONITOR connector (D-sub 15-pin)
1 Analog video signal output section
This outputs HD analog video signals. The output signals
can be switched with INTERFACE SELECT >D-SUB
1 COMPOSITE OUT connectors
2 Analog audio signal output section
COMPOSITE OUT
2 MONITOR
connector
1 AUDIO OUTPUT 1/3 and 2/4
connectors
MONITOR
2 AUDIO MONITOR
connectors
AUDIO MONITOR
R
L
AUDIO OUTPUT
2/4
1/3
a COMPOSITE OUT connectors (phono jack, BNC
type)
These output composite video signals.
When CHAR SEL on the HOME page of the function
such as timecode, menu settings, and error messages is
superimposed on the output signals.
18
Names and Functions of Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
a AUDIO OUTPUT (analog audio signal output) 1/3
and 2/4 connectors (XLR 3-pin, male)
4 External device connection section
These output two channels of analog audio.
For 4-channel audio, you can use the INTERFACE
SELECT >AUDIO OUTPUT item of the setup menu (see
page 85) to select whether to output channels 1 and 2, or
channels 3 and 4 (factory default setting: channels 1 and
2).
1 RS232C connector
2 REMOTE(9P) connector
RS232C
REMOTE(9P)
S400
You can set the output level with the setup menu item
AUDIO CONTROL >LEVEL SELECT (factory default
3
4
Remote connector
selector switch
b AUDIO MONITOR connectors (phono jack)
These output audio signals for monitoring.
You can select the channels to monitor with MONI CH and
MONI SEL on the HOME page of the function menu (see
S400 connector
5 U terminal
a RS232C (serial interface) connector (D-sub 9-pin,
male)
Connect a computer or other device with a serial interface
to control this unit from that device.
3 Power supply section
When you use this connector, set the remote connector
selector switch to the RS232C side, and set INTERFACE
SELECT >REMOTE I/F in the setup menu to “9PIN/RS-
1 - AC IN connector
2 POWER switch
-AC IN
POWER
b REMOTE(9P) (remote control 9-pin) connector
(D-sub 9-pin, RS-422A compliant, female)
To control this unit from a controller or VTR supporting
the RS-422A Sony 9-pin VTR protocol, connect the device
to this connector. When you use this connector, set the
remote connector selector switch to the REMOTE(9P)
side, and set INTERFACE SELECT > REMOTE I/F in the
a -AC IN (AC power input) connector
Connect to an AC power supply with the power cord (not
supplied).
c Remote connector selector switch
Push this switch to the side of the remote control connector
you are using, either the RS232C connector or the
REMOTE (9P) connector.
b POWER (main power) switch
Press the + side to power on the unit. Press the a side to
power off.
When using the unit, normally leave the POWER switch in
the + (on) position, and use the on/standby switch on the
front panel to switch the unit between the operating state
and standby state.
d
S400 connector (6-pin, IEEE1394 compliant)
Connect a DV device or computer using an i.LINK cable.
The following connection types are supported. They are
selected by setting INTERFACE SELECT >i.LINK
Note
AV/C (Audio/Video Control) connection: Output
DVCAM format digital video and audio signals
(i.LINK MODE set to “AV/C”).
If you press the on/standby switch on the front panel while
the unit is in the operating state, the unit saves its data and
then enters the standby state (the on/standby indicator
lights red). Before turning the main power off, always
check to be sure that the unit is in the standby state, and
then push the main power switch to the a side.
Audio output signals are 2ch or 4ch, as selected by
AUDIO CONTROL >DV OUT MODE in the setup
FAM (file access mode) connection: Input and output
files between this unit and a computer (i.LINK
MODE set to “FAM (PC REMOTE)”).
19
Names and Functions of Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the middle: SET button
Notes
• If video or audio signals from an external device
connected to the S400 connector fail to be output,
disconnect the i.LINK cable and connect it again,
pushing it straight in.
b THUMBNAIL key
This has the same function as the THUMBNAIL button on
the main unit.
• Before connecting or disconnecting an i.LINK cable
between this unit and a device with a 6-pin i.LINK
connector, power off the device and disconnect its power
cord from the electrical outlet. If the i.LINK cable is
connected or disconnected with the device’s power plug
still connected, high voltage (8 to 40 V) from the
device’s i.LINK connector can flow into this unit,
possibly damaging the unit.
c CHARACTER key
Each press of this key turns the character information
superimposed on the monitor screen on and off, or
switches to the LCD.
d SUB CLIP key
This has the same function as the SUB CLIP button on the
main unit.
• When connecting this unit to a device with a 6-pin
i.LINK connector, connect to the 6-pin i.LINK
connector of the other device first.
• Except in playback modes (jog and shuttle modes, etc.),
audio signals output from this connector and monitored
on another device may sound different from the audio
signals played back on this unit.
Note
Pressing this key has no effect when no clip list is
registered.
e Recording/playback control keys
PREV (previous) key: Press this to jump to the first frame
of the current clip. When pressed at the first frame of
the current clip, this button jumps to the first frame of
the previous clip.
e U (signal ground) terminal
Connect to the system ground.
PLAY key: Press this to start playback. Press the STOP
key to stop playback.
NEXT key: Press this to jump to the first frame of the next
clip.
Infrared Remote Commander
The corresponding functions are executed when you point
the remote commander at the infrared sensor of the main
unit and press the keys and setting pad.
If you want to disable control of this unit from the remote
commander, set INTERFACE SELECT >WIRELESS
STOP key: Press this to stop recording or playback.
f SEARCH keys
Press m to perform –5 times normal speed shuttle
playback in the reverse direction.
Press M to perform +5 times normal speed shuttle
playback in the forward direction.
1 Setting pad
PUSH SET
Using the infrared remote commander
2 THUMBNAIL key
THUMBNAIL SUB CLIP
Before use
3 CHARACTER key
CHARACTER
Pull out the insulation sheet.
4 SUB CLIP key
PREV
PLAY
NEXT
STOP
Insulation sheet
5 Recording/playback
control keys
SEARCH
6 SEARCH keys
a Setting pad
Positions on the pad correspond to functions of the main
unit, as follows.
To replace the lithium battery in the remote
commander
The remote commander uses a CR2025 Lithium Battery.
Do not use a battery other than the CR2025.
Press the top side: M/MARK1 button
Press the bottom side: m/MARK2 button
Press the left side: </IN button
1
Hold down the lock lever 1, and then pull out the
battery holder 2.
Press the right side: ,/OUT button
20
Names and Functions of Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
2
1
2
Insert a new battery with the + symbol facing upward
(1), and then push the battery holder until it clicks
(2).
Face the + symbol upward.
2
1
WARNING
Battery may explode if mistreated. Do not recharge,
disassemble or dispose of in fire.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s
instructions.
Battery lifetime
When the lithium battery output falls, even button presses
may not operate. The average lithium battery lifetime is
about one year, but this depends on the pattern of use.
If pressing the remote control buttons produces absolutely
no effect on this unit, replace the battery, then check the
operation again.
21
Names and Functions of Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparations
2
Chapter
SYSTEM SEL
Setting the System
Frequency
SYSTEM FREQ:
60I
50I
30P
25P
23.98P
This unit is shipped with the system frequency still unset.
Therefore, you need to set the system frequency before
using the unit. (The unit cannot be used unless the system
frequency is set.)
SELECT : ( )( )KEY
DATA SET :
SET KEY
Once it is set, the system frequency is retained even when
the unit is powered off.
2
3
Press the M/MARK1 button or the m/MARK2 button
to select the system frequency to use.
To set the system frequency
Use the following procedure.
Press the SET button.
“NOW SAVING...” appears in the time data display
section, and the modified setting is saved in the unit’s
memory.
Rear panel
“COMPLETE ! !” appears when save processing
finishes.
POWER
POWER
switch
1
2
If you have selected 60I or 30P
When you press the SET button with 60I or 30P
selected in step 2, the following screen appears.
EJECT
F1
F2
F3
F4
F5
0
0
TCG
EXT
-12
-20
-12
-20
TC MODE
PRESET
-30
-40
-60
-30
-40
-60
ACCESS
RUN MODE
REC RUN
1
2
3
4
VAR
MARK1
+
NETWORK
4CH 16 BIT
3
4
T C / V I T C
V I T C
MENU
CHAPTER
EXPAND
MPEG HD
SP
VITC
1080 60I
COOO1
LOCAL
REM:077M
DF/NDF
NDF
IN
OUT
SUB
CLIP
THUMB
NAIL
REMOTE
LEVEL
SYSTEM SEL
SET RESET
JOG
P2
00:00.00:00
PAGE DISPLAY
CLIP
ESSENCE
MARK
MENU
MARK2
PREV
PLAY
NEXT
STOP
TS REC
SHUTTLE
KEY INHI
CH
1
CH
2
CH
3
CH
4
PHONES
PRESET
PB
SYSTEM FREQ : 601
SHIFT
TOP
END
F
REV
F
FWD
STANDBY
UC/J SELECT :
UC
UCP
J
Time data display section
4
3
SELECT : ( )( )KEY
1
Power the unit on.
DATA SET :
SET KEY
“SYSTEM SEL” appears in the time data display
section.
Press the M/MARK1 and m/MARK2 buttons to select
“UC” (for areas outside Japan) or “J” (for Japan), then
press the SET button.
22
Setting the System Frequency
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Connections and
Settings
Be sure to carry out step 3 before powering the unit off
(putting it into standby). The new system frequency
setting will not be saved if you power off without
carrying out step 3.
Note
4
Press the on/standby switch to power the unit off (put
it into standby), and then press it again to power the
unit on.
Production of some of the peripherals and related devices
described in this chapter has been discontinued.
For advice about choosing devices, please contact your
Sony dealer or a Sony sales representative.
The selected system frequency becomes available for
use.
You can change the system frequency setting by using the
setup menu item OPERATIONAL FUNCTION >SYSTEM
SEL >SYSTEM FREQ.
For details about the setup menu, see page 77 “System
Menu” in Chapter 6.
Connecting an External Monitor
You can connect a video monitor to this unit’s video output
connectors or to the MONITOR connector. The following
figure shows an example using a Sony multi-format LCD
monitor.
Note
You can also superimpose character information such as
timecode and the unit’s operating status on output video.
For details, see “Superimposed Text Information” (page
32).
When the system frequency is set to 60I or 30P, select
drop-frame mode (DF) or non-drop-frame mode (NDF) on
To view HD video
Connect an HD video monitor using the method in the
following figure.
When you connect a monitor with this method, set the
setup menu item INTERFACE SELECT >D-SUB
23
Connections and Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPOSITE
OUT
AUDIO
MONITOR
AUDIO
MONITOR
PDW-F30 (this unit)
PDW-F30 (this unit)
OMPOSITE OUT
AUDIO MONITOR
COMPOSITE OUT
AUDIO MONITOR
-AC IN
R
L
-AC IN
POWER
R
L
POWER
AUDIO OUTPUT
2/4
AUDIO OUTPUT
2/4
1/3
1/3
MONITOR
RS232C
REMOTE(9P)
S400
MONITOR
RS232C
REMOTE(9P)
S400
MONITOR
COMPOSITE
IN connector
Y/P /P
B
R
connectors
AUDIO IN
connector
AUDIO IN
connector
MEU-WX2 Multi-Format Engine
MEU-WX2 Multi-Format Engine
LMD-172W/232W Multi-Format LCD Monitor
LMD-172W/232W Multi-Format LCD Monitor
Connection method and connection cables
Connection method Connection cables (not supplied)
Connection method and connection cables
Connection method Connection cables (not supplied)
Composite
75Ω coaxial cable, phono plug –
stereo miniplug cable
Component (Y/P /P ) D-Sub 15-pin – analog component
B
R
cable, phono plug – stereo miniplug
cable
Using PDZ-1 Over an i.LINK
Connection (FAM Connection)
To view SD video
Connect an SD video monitor using the method in the
following figure.
You can use the supplied PDZ-1 Proxy Browsing Software
to do simple editing of proxy AV data. The following
explains how to make an i.LINK connection between this
unit and a computer with PDZ-1 installed, and how to
access this unit by FAM (file access mode).
Notes
• The required FAM driver is also installed when you
install the PDZ-1 software.
• This unit’s S400 connector has 6 pins. Check the
number of pins on the i.LINK connector of your
notebook computer, and use an appropriate i.LINK
cable.
24
Connections and Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
See “Using PDZ-1 Proxy Browsing Software” in Chapter
4 (page 68) for more information about installing the
PDZ-1 software. See the online help of PDZ-1 for more
information about using PDZ-1.
• To transfer video and audio signals (AV/C data), use
the setup menu to select the audio mode (the factory
default is “2ch”).
• This unit’s S400 connector has 6 pins. Check the
number of pins on the i.LINK connector of your laptop
computer, and use an appropriate i.LINK cable.
Some limitations apply to FAM connections. For details,
see “File Operations in File Access Mode” in Chapter 5
PDW-F30 (this unit)
COMPOSITE OUT
AUDIO MONITOR
-AC IN
R
L
POWER
PDW-F30 (this unit)
COMPOSITE OUT
AUDIO MONITOR
-AC IN
AUDIO OUTPUT
2/4
R
L
POWER
1/3
AUDIO OUTPUT
2/4
1/3
MONITOR
RS232C
REMOTE(9P)
S400
MONITOR
RS232C
REMOTE(9P)
S400
S400
S400
i.LINK cable
(not supplied)
i.LINK cable
(not supplied)
i.LINK (IEEE1394) connector
Laptop computer
i.LINK (IEEE1394) connector
Laptop computer
On the computer
On this unit
Install editing software
supporting the DVCAM
format.
Set the setup menu item
INTERFACE SELECT
>REMOTE I/F to “i.LINK” (see
On the computer
On this unit
Install PDZ-1.
Set the setup menu item
INTERFACE SELECT >i.LINK
MODE to “FAM(PC REMOTE)”
Set the setup menu item
INTERFACE SELECT >i.LINK
MODE to “AV/C” (see page
85).
Connecting to a Nonlinear Editing
System (AV/C Connection)
Connections for Cut Editing
You can send video/audio signals (AV/C data) from this
unit to a nonlinear editing system connected to the S400
connector.
By connecting this unit to a VTR, you can configure a cut
editing system. Some example connections are shown in
the following.
The following figure shows an example connection.
Connection)” (page 24) for the connections and settings to
make a FAM connection between this unit and a nonlinear
editing system.
When making the connections, also refer to the manuals
provided with the equipment to be connected.
When using the editing functions of the
recorder (connections using the S400
connector)
The following figure shows a cut editing system
comprising this unit as a player and a DSR-2000A/2000AP
unit as a recorder. In this system, video/audio signals and
control signals are all transferred through the S400
connector.
Notes
• The S400 connector of this unit outputs video/audio
signals in DVCAM format. Data recorded in MPEG HD
format is output after being converted into DVCAM
format.
• The nonlinear editing system to be connected to this unit
requires editing software (not supplied) supporting the
DVCAM format.
25
Connections and Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
SD video monitor
Editing Control Unit Settings
To composite video input connector
To analog audio input connector
When connecting an editing control unit to use with this
unit, make the following settings.
BVE-700/700A
2
1
Set VTR constants as follows.
COMPOSITE
OUT
AUDIO
PDW-F30 (this unit, player)
MONITOR
System
frequency
VTR CONSTANT 1
COMPOSITE OUT
AUDIO MONITOR
-AC IN
R
L
POWER
1
2
3
4
5
6
7
8
AUDIO OUTPUT
2/4
1/3
30P/60I
25P/50I
24P
A0 94
A1 94
A2 94
00
00
00
96
16
16
16
16
03
03
03
80
80
80
7D 16
MONITOR
RS232C
REMOTE(9P)
S400
78
16
S400
System
frequency
VTR CONSTANT 2
4
1
2
3
4
5
6
7
8
DSR-2000A/2000AP (recorder)
i.LINK
30P/60I
25P/50I
24P
0A 07
0A 07
0A 07
FE 00
FE 00
FE 00
80
80
80
5A FF 5A
4C FF 4B
48
FF 48
Remote Control Unit Settings
VIDEO OUT 3
(SUPER)
MONITOR
You can control this unit from an RM-280 Remote Control
Unit.
Connect this unit to the RM-280 with a 9-pin remote
control cable (not supplied), and make the settings in the
following table.
AUDIO
1
To composite
video input
connector
3
To analog audio input connector
RM-280 settings
Settings on this unit
SD video monitor
EDITOR/REMOTE
CONTROL:
REMOTE
Setup menu item INTERFACE
SELECT >REMOTE I/F (see
page 85): 9PIN/RS-232C
1: 75Ω coaxial cable (not supplied)
CONTROL
Setup menu item 19
FNC MODE:
XDCAM
Remote control switch: REMOTE
2: Phono plug – stereo miniplug cable (not supplied)
Remote connector selector
switch: REMOTE(9P)
3: Phono plug cable (not supplied)
4: i.LINK cable (not supplied)
DSR-2000A/2000AP
(recorder) settings
This unit’s (player) settings
i.LINK button: Lit
Remote control switch:
REMOTE
SDTI/i.LINK button: i.LINK Set the setup menu item
INTERFACE SELECT
>REMOTE I/F to “i.LINK” (see
For details about the settings of the DSR-2000A/2000AP,
refer to the operating instructions for that unit.
26
Connections and Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
DATE/TIME PRESET
Setup
YEAR
MONTH
DAY
2006
04
08
The principal setup operations before operating this unit
are carried out using setup menus.
TIME 10:09:17
TIME ZONE UTC_00:00
This section explains how to set the date and time and how
to adjust the brightness of the LCD panel.
INC/DEC : JOG DIAL
SHIFT : ( )( )KEY
DATE SAVE : SET KEY
TO MENU : MENU KEY
about menu operations and menu items.
This screen allows you to set the following items.
YEAR: Calendar year
MONTH: Month
DAY: Day
Setting the Date and Time
TIME: Time
TIME ZONE: Time zone (difference from UTC)
When using this unit for the first time, you should set the
date and time as follows.
3
Set the date, time and time zone.
Note
You can change the setting of the flashing digits.
Before starting, press the DISPLAY button to set the
monitor video section to its largest size. Or connect an
external video monitor to this unit and superimpose menus
(see page 32) on the monitor screen.
To change the flashing digits
Use the arrow buttons (</IN, ,/OUT).
To increase or decrease the values of the flashing
digits
1,4 3 2,3
Use the arrow buttons (M/MARK1, m/MARK2) or jog
dial.
EJECT
F1
0
0
TCG
EXT
-12
-20
-12
-20
F2
F3
F4
F5
TC MODE
PRESET
-30
-40
-30
-40
ACCESS
RUN MODE
REC RUN
-60
-60
To return the settings to the initial values
Press the RESET button.
1
2
3
4
VAR
MARK1
+
NETWORK
4CH 16 BIT
3
4
T C / V I T C
V I T C
MENU
CHAPTER
EXPAND
MPEG HD
SP
VITC
1080 60I
COOO1
LOCAL
REM:077M
DF/NDF
NDF
IN
OUT
SUB
CLIP
THUMB
NAIL
REMOTE
LEVEL
SET RESET
JOG
P2
00:00.00:00
PAGE DISPLAY
CLIP
ESSENCE
MARK
MENU
MARK2
PREV
PLAY
NEXT
STOP
TS REC
SHUTTLE
KEY INHI
CH
1
CH
2
CH
3
CH
4
PHONES
PRESET
PB
SHIFT
4
When you have made the necessary settings, press the
SET button.
TOP
END
F
REV
F
FWD
STANDBY
The message “NOW SAVING...” appears, the settings
are saved, and the menu closes.
4 3
3
1
2
Press the MENU button.
To clear the menu from the screen without saving
settings
Press the MENU button twice in succession.
The system menu appears on the monitor screen (see
Select DATE/TIME PRESET using the M/MARK1
button or m/MARK2 button, then press the ,/OUT
button.
Adjusting the Brightness of the LCD
Panel
The DATE/TIME PRESET screen appears on the
monitor.
Proceed as follows to adjust the brightness of the LCD
panel.
Note
Before starting, press the DISPLAY button to set the
monitor video section to its largest size. Or connect an
external video monitor to this unit and superimpose menus
(see page 32) on the monitor screen.
27
Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the arrow buttons (M/MARK1, m/MARK2) or jog
dial.
1 5 2,3,4,5
To return the settings to the factory defaults
Press the RESET button.
EJECT
F1
F2
F3
F4
F5
0
0
TCG
EXT
-12
-20
-12
-20
TC MODE
PRESET
-30
-40
-60
-30
-40
-60
ACCESS
RUN MODE
REC RUN
1
2
3
4
VAR
MARK1
+
NETWORK
4CH 16 BIT
3
4
T C / V I T C
V I T C
MENU
CHAPTER
EXPAND
MPEG HD
SP
VITC
1080 60I
COOO1
LOCAL
REM:077M
DF/NDF
NDF
IN
OUT
SUB
CLIP
THUMB
NAIL
REMOTE
LEVEL
SET RESET
JOG
P2
00:00.00:00
PAGE DISPLAY
6
When you are finished making adjustments, press the
SET button.
CLIP
ESSENCE
MARK
MENU
MARK2
PREV
PLAY
NEXT
STOP
TS REC
SHUTTLE
KEY INHI
CH
1
CH
2
CH
3
CH
4
PHONES
PRESET
PB
SHIFT
TOP
END
F
REV
F
FWD
STANDBY
The message “NOW SAVING...” appears, the settings
are saved, and the menu closes.
6 5
5
To clear the menu from the screen without saving
adjustments
1
2
Press the MENU button.
Press the MENU button twice in succession.
The system menu appears on the monitor screen (see
Select SETUP MENU using the M/MARK1 button or
m/MARK2 button, then press the ,/OUT button.
The setup menu appears on the monitor screen (see
3
4
Select DISPLAY CONTROL using the M/MARK1
button or m/MARK2 button, then press the ,/OUT
button.
The DISPLAY CONTROL menu appears on the
Select BRIGHTNESS using the M/MARK1 button or
m/MARK2 button, then press the ,/OUT button.
The LCD BRIGHTNESS screen appears on the
monitor.
SETUP MENU
LCD BRIGHTNESS
preset :55H
55 (HEX)
SHIFT : ( )( )KEY
INC/DEC : JOG DIAL
TO MENU : MENU KEY
5
Adjust the brightness while viewing the screen.
You can change the values of digits which flash in the
settings screen. Setting values are hexadecimal (00 to
7F (HEX)).
To change the flashing digits
Use the arrow buttons (</IN, ,/OUT).
To increase or decrease the values of the flashing
digits
28
Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENU
OPERATIONAL FUNCTION
24P (23.98P) Mode
Settings
DISPLAY CONTROL
TIME CODE
DISC PROTECTION
VIDEO CONTROL
AUDIO CONTROL
INTERFACE SELECT
METADATA
Selecting the Playback Mode
(23.98PsF or 2-3 Pulldown)
SETUP BANK OPERATION
ENHAN
MENU GRADE
When the setup menu item SYSTEM FREQ is set to
“23.98P”, you can set monitor output to either 23.98PsF
mode or 2-3 pulldown mode.
9
Press the ,/OUT button.
The second level of the OPERATIONAL FUNCTION
menu appears.
1
Press the MENU button.
SETUP MENU
OPERATIONAL FUNCTION
2
3
Press the M/MARK1 or m/MARK2 button to select
REPEAT MODE
AUTO EE SELECT
LOCAL ENABLE
REC FORMAT
:OFF
SETUP MENU.
:STP&EJ
:SP
Press the ,/OUT button.
DISC END
:EJECT
CLIP TITLE
The setup menu appears.
FILE NAMING
SYSTEM SEL
SEARCH ENABLE
VAR SPD LIMIT
:DIAL
:OFF
4
5
Press the m/MARK2 button to select MENU GRADE.
Press the ,/OUT button.
10Press the M/MARK1 or m/MARK2 button to select
The second level of the MENU GRADE menu
appears.
“SYSTEM SEL”.
11Press the ,/OUT button.
SETUP MENU
The third level of the menu appears.
: BASIC
MENU GRADE
* BASIC
ENHANCED
]
SETUP MENU
OPERATIONAL FUNCTION
SYSTEM SEL
SYSTEM FREQ : 60I
UC/J
: J
23.9P OUTPUT: PsF
6
7
Press the m/MARK2 button to select ENHANCED.
Press the </IN button.
12Press the M/MARK1 or m/MARK2 button to select
The enhanced menu items appear.
“SYSTEM FREQ”.
8
Press the M/MARK1 button to select
“OPERATIONAL FUNCTION”.
13Press the ,/OUT button.
Setting values appear.
29
24P (23.98P) Mode Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENU
OPERATIONAL FUNCTION
Output Signals in 24P (23.98P) Mode
SYSTEM SEL
The following tables show the signals output by the unit
when “23.98PsF” and “2-3 PULL DOWN” are selected.
SYSTEM FREQ : 601
* 60I
50I
30P
Output signals
25P
23.98P
Output
Type
23.98PsF
2-3 PULL
DOWN
Output
signals
Composite
output
No output
Video and
audio signals
pulled down to
59.94i
14Press the m/MARK2 button to select “23.98P”.
i.LINK DV
output
15If you want to change the monitor output setting as
well, press the </IN button to return to the higher
level screen (the state of step 11). If you do not want
to change the monitor output setting, proceed to step
19.
i.LINK TS
output
Timecode COMPOSITE –
output VITC output
30-frame
timecode after
pulldown
conversion
16Press the m/MARK2 button to select “23.9P
OUTPUT”.
Timecode display
17Press the ,/OUT button.
Type
23.98PsF
2-3 PULL DOWN
LTC display
PDT display
VITC display
24-frame timecode
–
The setting value appears.
30-frametimecode
after pulldown
conversion
SETUP MENU
OPERATIONAL FUNCTION
SYSTEM SEL
24-frametimecode
COUNTER display 24-frame signals
30-frame signals
after pulldown
conversion
23.9P OUTPUT: PsF
* 23.98PsF
2-3 PULL DOWN
Timecode in remote timecode mode
Type
23.98PsF
2-3 PULL DOWN
9-pin preset
timecode
24-frame timecode
18Press the M/MARK1 or m/MARK2 button to select
9-pin preset
timer 1 (Counter)
24-frame signals
30-frame signals
after pulldown
conversion
one of the following.
23.98PsF: Output as 23.98P.
2-3 PULL DOWN: Output after pulldown conversion
to 59.94i.
9-pin scene
timecode
24-frame timecode 30-frame timecode
after pulldown
conversion
9-pin scene
timer 1 (Counter)
24-frame signals
30-frame signals
after pulldown
conversion
19Press the SET button.
A confirmation message appears.
See the optional “9pin Manual ‘PDW Series PROTOCOL
OF REMOTE(9-pin) CONNECTOR’” for more
information about remote timecode mode.
20Press the SET button to confirm the changes, or the
RESET button to cancel them.
If you have pressed the SET button, power the unit off
and on again to enable the changes.
30
24P (23.98P) Mode Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
frame sequence. The following figure shows the playback
frame sequence when 01:00:00:00 has been set for the 24-
frame timecode and 10:00:00:00 has been set for the 30-
frame timecode.
Playback in 24P (23.98P) 2-3
Pulldown Mode
Pulldown playback frame sequences
Note
During pulldown mode playback, playback is carried out
so that the 24-frame timecode set with TIME CODE >PD
PRESET in the setup menu becomes the “A-frame” of the
This kind of frame sequence adjustment is not carried out
for clip list playback.
Timecode
conversion
reference
24P: 1frame
24P Video
n-2
00:59:59:22
C-frame
n-1
00:59:59:23
D-frame
n
n+1
01:00:00:01
B-frame
n+2
01:00:00:02
C-frame
n+3
01:00:00:03
D-frame
n+4
01:00:00:04
A-frame
Frame Count
TC (24F)
Frame Seqence
01:00:00:00
A-frame
60i: 1frame
60i Pulldown Video
TC (30F)
09:59:59:28 09:59:59:29 10:00:00:00 10:00:00:01 10:00:00:02 10:00:00:03 10:00:00:04 10:00:00:05
Timecode during playback of pulldown
signals
During playback of pulldown signals, timecode is
converted to 30 frames to match the 59.94i video output
signals.
SETUP MENU
OPERATIONAL FUNCTION
DISPLAY CONTROL
SETUP BANK OPERATION
MENU GRADE
:BASIC
The values of “24F TC” and “30F TC” under TIME CODE
>PD PRESET in the setup menu are used as the conversion
references.
To display 30-frame pulldown timecode in the
monitor video display section or on an external
monitor
5
6
Press the ,/OUT button.
1
Press the MENU button.
The second level of the DISPLAY CONTROL menu
appears.
Press the M/MARK1 or m/MARK2 button to select
“DISPLAY INFO”.
2
3
Press the M/MARK1 or m/MARK2 button to select
SETUP MENU.
SETUP MENU
Press the ,/OUT button.
DISPLAY CONTROL
:ON
CHARA.DISPLAY
CHARA.POSITION
CHARA.TYPE
CHARA.VSIZE
DISPLAY INFO
SUB STATUS
MENU DISPLAY
BRIGHTNESS
ALARM
The setup menu appears.
:WHITE
:x1
4
Press the M/MARK1 or m/MARK2 button to select
“DISPLAY CONTROL”.
:T&STA
:OFF
:WHITE
:55%
:ON
7
Press the ,/OUT button.
The third level of the menu appears.
31
24P (23.98P) Mode Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENU
DISPLAY CONTROL
DISPLAY INFO
Superimposed Text
Information
:T&STA
* TIME DATA & STATUS
TIME DATA & UB
TIME DATA & CNT
TIME DATA & TIME
TIME DATA & CLIP
TIME DATA ONLY
The composite signals output from the COMPOSITE OUT
connector can contain superimposed text information,
including timecode, menu settings, and alarm messages.
To turn superimposed text on and off
Set the CHAR SEL item on page P1 of the function menu.
ON: Display superimposed text.
OFF: Do not display superimposed text.
LCD: Display superimposed text on the LCD panel of this
unit, but do not display it on an external video monitor
connected to this unit.
8
9
Press the M/MARK1 or m/MARK2 button to select
“TIME DATA ONLY”.
Press the SET button.
The setting is confirmed.
10Turn the display of character information on.
Note
For details, see “To turn superimposed text on and
Even when ON is selected, you can forcibly turn off the
superimposition of character information in HD output by
setting the SETUP MENU >DISPLAY CONTROL >HD
CHARA item.
As shown below, you can display 24-frame timecode
at the same time as 30-frame pulldown timecode.
L T C
P D T
0 0
0 0
:
:
5 9
5 9
:
.
5 9
5 9
:
:
2 3
2 8
Adjusting the text display
You can use the items in the DISPLAY CONTROL setup
menu to specify the position, size, and type of
superimposed characters.
See page 81 for more information about the items in the
DISPLAY CONTROL menu.
Information displayed
1 Type of time data
2 Timecode reader drop
a)
frame mark
3 Timecode generator drop
a)
frame mark
Time data
4 VITC field mark
T C R
0 0
:
0 4
.
4 7
.
0 7 *
P L A Y
L O C K
5 Menu setting states
6 Operation mode
a) Only when the system frequency is 60I/30P.
32
Superimposed Text Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Display
Description
Note
B2
The current menu settings are the same as the
settings in menu bank 2.
The display shown above corresponds to the factory
default settings of the unit.
You can use DISPLAY CONTROL >DISPLAY INFO
(page 81) in the setup menu to change the information
shown in the second line.
B3
DF
The current menu settings are the same as the
settings in menu bank 3.
The current menu settings are the same as the
factory defaults.
No
display
The current menu settings are different from all
of the above.
See page 86 “Setup Menu Operations” in Chapter 6 for
more information about how to use the setup menu.
f Operation mode
a Type of time data
The field is divided into two blocks as shown below.
• Block A displays the operation mode.
• Block B displays the servo lock status or playback speed.
Display Meaning
CNT
TCR
UBR
TCR.
UBR.
TCG
UBG
IN
Counter data
TC reader timecode data
TC reader user bits data
VITC reader timecode
VITC reader user bits data
TC generator timecode
TC generator user bits data
In point time data
B
A
Display
Operation mode
Disc is not loaded.
Block A
Block B
DISC OUT
LOADING
OUT
DUR
Out point time data
Disc is being
loaded.
Duration between In point and Out point
UNLOADING
Disc is being
unloaded.
Note
If the time data or user bits cannot be read correctly, they
will be displayed with an asterisk. For example, “T*R”,
“U*R”, “T*R.” or “U*R.”.
STANDBY OFF
STOP
Standby-off mode
Stop mode
NEXT
Cuing up to the first
frame of the next
clip.
b Timecode reader drop-frame mark (for system
frequency 60I/30P only)
“.”: Indicates drop-frame mode
PREV
Cuing up to the first
frame of the current
clip.
“:”: Indicates non-drop-frame mode
F.FWD
F.REV
PLAY
Fast forward search
Fast reverse search
c Timecode generator drop-frame mark (for system
frequency 60I/30P only)
“.”: Indicates drop-frame mode (factory default)
“:”: Indicates non-drop-frame mode
Playback mode
(servo unlocked)
PLAY
LOCK
Playback mode
(servo locked)
d VITC field mark
“ ” (blank): Fields 1 and 3 (for system frequency 60I/30P)
or fields 1, 3, 5 and 7 (for system frequency 50I/25P)
“*”: Fields 2 and 4 (for system frequency 60I/30P) or
fields 2, 4, 6 and 8 (for system frequency 50I/25P)
REC
Record mode
(servo unlocked)
REC
LOCK
STILL
FWD
Record mode
(servo locked)
JOG
A still picture in jog
mode
e Menu setting states
This is displayed when the setup menu item DISPLAY
CONTROL >MENU STATUS is set to “ENABLE” (see
JOG
Jog mode in
forward direction
JOG
REV
Jog mode in
reverse direction
Display
Description
SHUTTLE
SHUTTLE
STILL
(Speed)
A still picture in
shuttle mode
B1
The current menu settings are the same as the
settings in menu bank 1.
Shuttle mode
33
Superimposed Text Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Display
Block A
VAR
Operation mode
On-screen
indication
Meaning
Block B
EXT DVIN-T&U
The internal timecode generator is in
synchronization with the external
timecode input to the unit via the
(Speed)
Variable speed
mode
TOP 0001/xxxx
END xxxx/xxxx
PREROLL
Cuing up to the first
frame of the first
clip.
S400 connector and is generating the
same timecode values and user bit
values as those of the external
timecode (regeneration).
Cuing up to the last
frame of the last
clip.
EXT DVIN.V-T&U The internal timecode generator is in
synchronization with the external VITC
Cuing up during
preroll
input to the unit via the S400
connector interface and is generating
the same timecode values and user bit
values as those of the external
timecode (regeneration).
Displaying Supplementary Status
Information
When the menu item SUB STATUS is set to
“REMAIN”:
When you set the setup menu item DISPLAY CONTROL
can view supplementary status information on the monitor
screen below the operating mode display area.
On-screen
indication
Meaning
REMAIN 120 min
Remaining capacity of the disc in
minutes. When the remaining capacity
has not been calculated, “REMAIN ---
min” appears.
.
.
T C R
0 0
P L A Y
I N S
:
0 4
A 1
4 7
L O C K
3 4 T C
0 7
2
V
Supplementary status information
The following items of supplementary status information
are displayed depending on the setting of the menu item
SUB STATUS.
Setting of menu item
SUB STATUS
Items of supplementary
information displayed
TC MODE
REMAIN
CLIP NO
Operating mode of the internal
timecode generator
Amount of free capacity on the
disc (in minute units).
Clip number
The following tables show the on-screen indications of
supplementary information and their meaning.
When the menu item SUB STATUS is set to “TC
MODE”:
On-screen
indication
Meaning
INT PRST FREE
The internal timecode generator is
operating in FREE RUN mode.
INT PRST REC
The internal timecode generator is
operating in REC RUN mode.
INT REGEN-T&U The internal timecode generator is in
synchronization with the playback
timecode (LTC) read from disc.
34
Superimposed Text Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording and Playback
3
Chapter
• Do not leave cartridges where dust may get inside.
• Store cartridges in their cases.
Handling Discs
Care of the discs
• Remove dust and dirt on the outside of a cartridge using
a soft dry cloth.
• If condensation forms, allow ample time to dry before
use.
Discs Used for Recording and
Playback
This unit uses the following disc for recording and
playback:
Write-Protecting Discs
1)
PFD23 Professional Disc (capacity 23.3 GB)
To protect the content recorded on the disc from accidental
erasure, move the Write Inhibit tab on the lower surface of
the disc in the direction of the arrow, as shown in the
following figure.
1) Professional Disc is a trademark of Sony Corporation.
Note
It is not possible to use the following discs for recording or
playback:
Lower surface of the disc
Write Inhibit tab
• Blu-ray Disc
• Professional Disc for Data
Notes on Handling
Handling
The Professional Disc is housed in a cartridge, and is
designed to allow handling free of risk from dust or
fingerprints. However, if the cartridge is subjected to a
severe shock, for example by dropping it, this can result in
damage or scratching of the disc. If the disc is scratched, it
may be impossible to record video/audio, or to play back
the content recorded on the disc. The discs should be
handled and stored carefully.
• Do not touch the surface of the disc itself within the
cartridge.
• Deliberately opening the shutter may cause damage.
• Do not disassemble the cartridge.
E
V
A
S
Slide in the direction of the arrow
Write Inhibit tab settings
SAVE
SAVE
Recording disabled
Recording enabled
You can also write protect individual clips. For details, see
• The supplied adhesive labels are recommended for
indexing discs. Apply the label in the correct position.
Loading and Unloading a Disc
Storage
• Do not store discs where they may be subjected to direct
sunlight, or in other places where the temperature or
humidity is high.
When the on/standby switch indicator is lit green, you can
load and unload a disc as shown in the following figure.
35
Handling Discs
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Select “DISC MENU” using the M/MARK1 button or
On/standby switch and indicator
m/MARK2 button, then press the ,/OUT button.
Select “FORMAT” using the m/MARK2 button, then
press the ,/OUT button.
To unload
Press the EJECT button.
The menu item QUICK FORMAT is selected.
5
6
Press the ,/OUT button.
The message “QUICK FORMAT OK?” appears.
To cancel a disc format
Press the RESET button to return to the state of step 3.
To clear the menu from the screen, carry out step 7.
Press the SET button.
To load
Insert a disc face up.
The disc is drawn in.
The format starts.
The message “FORMAT COMPLETED.” appears
when formatting of the disc is completed.
The disc slot indicator flashes orange when you insert a
disc, and lights blue when the disc is completely loaded.
The indicator flashes blue when you eject a disc, and goes
out when the disc is completely ejected.
If you want to continue by formatting another disc
When the message “FORMAT COMPLETED.”
appears, press the EJECT button to eject the disc.
Insert the next disc to format, and press the SET button
when the message “QUICK FORMAT OK?” appears.
Formatting a Disc
7
Press the MENU button to clear the menu from the
screen.
Unused discs are formatted automatically when they are
loaded into this unit.
To format a recorded disc, load the disc into the unit, then
proceed as follows.
Handling of Discs When Recording
Does Not End Normally (Salvage
Functions)
Note
When a recorded disc is formatted, all the data on the disc
Recording processing does not end normally if, for
example, the POWER switch on the rear panel is turned off
during recording, or if the power cord is disconnected
during recording. Because the file system is not updated,
video and audio data recorded in real time is not
recognized as files and clip contents recorded up to that
point are lost.
However, this unit has salvage functions which can hold
losses to the minimum by reconstructing clips on such
discs.
1 2,7 3,4,5
EJECT
F1
F2
ACCESS
F3
VAR
MARK1
NETWORK
LOCAL
MENU
F4
CHAPTER
EXPAND
IN
OUT
SUB
CLIP
THUMB
NAIL
REMOTE
LEVEL
F5
SET RESET
JOG
PAGE DISPLAY
CLIP
ESSENCE
MARK
MENU
MARK2
PREV
PLAY
NEXT
STOP
TS REC
SHUTTLE
KEY INHI
CH
1
CH
2
CH
3
CH
4
PHONES
PRESET
PB
SHIFT
TOP
END
F
REV
F
FWD
STANDBY
There is a quick salvage function which executes
automatically and a full salvage function which you can
execute as required.
Quick salvage: Clips are reconstructed on the basis of
backup data stored in nonvolatile memory and
markers recorded on the disc. Processing time is about
5 seconds.
6
1
2
Press the DISPLAY button to maximize the monitor
video section.
Quick salvage executes automatically if the unit is
powered on with a disc still loaded after recording
was interrupted by power off.
Press the MENU button.
The system menu appears on the display.
36
Handling Discs
Download from Www.Somanuals.com. All Manuals Search And Download.
Full salvage: Clips are reconstructed on the basis of
markers recorded on the disc. Nonvolatile memory
cannot be used, so processing takes longer than for a
quick salvage (about 30 seconds, although it depends
on the state of the disc).
2
Press the SET button.
Processing begins and the message “Executing.”
appears.
When processing finishes, a message appears to
display the results.
If the message reads “Incomplete!”, the clips that
failed were lost.
You are prompted to execute a full salvage whenever
you insert a disc that was removed manually from a
powered off device after interruption of recording by
power off.
Note that no recorded clip contents are lost when the on/
standby switch on the front panel is set to standby during
recording, because the unit does not enter standby mode
until after the end of recording processing.
Notes
• Even after recording finishes, do not set the POWER
switch on the rear panel to off until the ACCESS
indicator has gone out.
• These functions salvage as much recorded material as
possible after an unforeseen accident, but 100%
restoration cannot be guaranteed.
• Even when these functions are used, it is not possible to
recover data from immediately before the interruption of
recording. The amount of data lost is as follows.
Quick salvage: From 2 to 4 seconds of data before the
interruption of recording.
Full salvage: From 4 to 6 seconds of data before the
interruption of recording.
• You are prompted to execute a full salvage every time
you insert a disc that has not been salvaged, or power the
unit on with such as disc loaded.
• No recording is possible on discs containing clips that
have not been salvaged, although it is possible to play
back the normally recorded sections. Recording
becomes possible if you perform a quick format, but this
erases all of the original recorded content.
To restore clips with a full salvage
1
Insert the disc on which recording did not end
normally.
The message “Salvage ?” appears on the display.
To cancel the clip salvage
Press the RESET button.
Notes
• The message “EJECT?” appears when “REC INH”
is displayed in the operation modes section of the
display. If the disc is write protected, eject the disc,
set the Write Inhibit tab to enable recording, and
then insert the disc again.
• This operation cannot be cancelled once it begins.
37
Handling Discs
Download from Www.Somanuals.com. All Manuals Search And Download.
To set the audio recording format
Set AUDIO CONTROL >REC MODE in the setup menu
to one of the following.
Recording
Menu setting Display
Audio recording
format
This section describes video and audio recording on the
unit.
2ch×16bit
4ch×16bit
2CH 16BIT
4CH 16BIT
2 channels/16 bits
4 channels/16 bits
See page 75 “Function Menu” in Chapter 6 for more
information about function menu operations.
Recording Timecode and User Bit
Values
See page 86 “Setup Menu Operations” in Chapter 6 for
more information about setup menu operations.
There are the following four ways of recording timecode:
Internal Preset mode: This records the output of the
internal timecode generator, set beforehand to an
initial value. The following run modes can be
selected.
Note
It is not possible to combine material recorded in different
system frequencies and audio recording formats on a
single disc (although different bit rates may be combined).
If you attempt to record material in a system frequency or
audio recording format that differs from that of existing
recorded material on the disc, “REC INH” appears on the
display and recording is inhibited.
• Free Run: Timecode advances continually.
• Rec Run: Timecode advances only during
recording.
Internal Regen mode: This records the output of the
internal timecode generator, initialized to timecode
following continuously upon the timecode of the last
frame of the last clip on the disc.
Make the following settings and adjustments before
starting to record.
Recording format settings: See the next section “To set
the video and audio recording formats”.
Timecode and user bits settings: See “Recording
Selection of time data to display: Select with CNTR SEL
on the HOME page of the function menu.
Selection of audio channels to monitor: Select with
MONI CH and MONI SEL on the HOME page of the
function menu.
To record timecode after setting an initial
value (Internal Preset)
To set an initial value
1 2 3,5 5 4,5
Volume adjustment of the monitor audio: Adjust with
the LEVEL knob.
EJECT
F1
F2
ACCESS
F3
Remote/local setting: Set the remote control switch. If
you set it to REMOTE, also set the setup menu item
INTERFACE SELECT >REMOTE I/F (“REMOTE”
and the connector used appear on the display).
VAR
MARK1
NETWORK
LOCAL
MENU
F4
CHAPTER
EXPAND
IN
OUT
SUB
CLIP
THUMB
NAIL
REMOTE
LEVEL
F5
SET RESET
JOG
PAGE DISPLAY
CLIP
ESSENCE
MARK
MENU
MARK2
PREV
PLAY
NEXT
STOP
TS REC
SHUTTLE
KEY INHI
CH
1
CH
2
CH
3
CH
4
PHONES
PRESET
PB
SHIFT
TOP
END
F
REV
F
FWD
STANDBY
6
To set the video and audio recording
formats
1
Make the following settings in the function menu.
To set the video recording format
• Set CNTR SEL on the HOME page to “TC”.
• Set TC MODE on page P1 to “PRESET”.
Set the video bit rate (compression method) by setting
OPERATIONAL FUNCTION >REC FORMAT in the
setup menu to one of the following.
2
3
Press the DISPLAY button to maximize the monitor
video section.
Menu setting/display
Video bit rate
VBR 35 Mbps
CBR 25 Mbps
VBR 18 Mbps
HQ
SP
LP
Press the MENU button.
The system menu appears on the display.
4
Select “TC PRESET” using the M/MARK1 button or
m/MARK2 button, then press the ,/OUT button.
38
Recording
Download from Www.Somanuals.com. All Manuals Search And Download.
The TC PRESET MODE screen appears.
The UB PRESET MODE screen appears.
TC PRESET MODE
UB PRESET MODE
TCG 00:00:00:00
UBG 00:00:00:00
INC/DEC : ( )( )KEY
SHIFT : ( )( )KEY
CLEAR : RESET KEY
DATA SAVE : SET KEY
ABORT : MENU KEY
INC/DEC : ( )( )KEY
SHIFT : ( )( )KEY
CLEAR : RESET KEY
DATA SAVE : SET KEY
ABORT : MENU KEY
5
6
Use the arrow buttons and the RESET button to set the
initial timecode value.
3
Use the arrow buttons and the RESET button to set the
user bits.
</IN button or ,/OUT button: Select the digit to
change (it flashes).
</IN button or ,/OUT button: Select the digit to
change (it flashes).
M/MARK1 button or m/MARK2 button: Change
M/MARK1 button or m/MARK2 button: Change
the value of the selected digit.
the value of the selected digit.
RESET button: Reset all digits to 0.
RESET button: Reset all digits to 0.
To cancel the timecode setting
Press the MENU button.
Settings are made in hexadecimal (0, 1, 2,... 8, 9, A,
B,... E, F).
Press the SET button.
To cancel the user bits setting
Press the MENU button.
The message “NOW SAVING...” appears, and the
timecode set in step 5 is displayed.
If RUN MODE on page P1 of the function menu is set
to “FREE RUN”, timecode begins to advance from the
initial value you just set.
4
Press the SET button.
The message “NOW SAVING...” appears, and the
user bits set in step 3 are displayed.
To set timecode to the current time
To record timecode that follows
sequentially upon the last recorded
timecode (Internal Regen)
You can record timecode so that it is continuous from one
clip to the next on the disc.
Set TC MODE on page P1 of the function menu to “INT”,
and TCG to “REGEN”. When this setting is in force, the
unit reads the timecode of the last frame of the last
recorded clip on the disc before starting to record, and
internally generates timecode that follows upon the
recorded timecode.
1
2
Set RUN MODE on page P1 of the function menu to
“FREE RUN”, and set DF/NDF to “DF”.
Preset)” to set the timecode to a time slightly ahead of
the current time.
3
Press the SET button at the instant when the current
time matches the displayed timecode.
In this case, the setting of DF/NDF on page P1 of the
function menu is ignored. New timecode is recorded in the
drop-frame mode of the last recorded timecode on the disc.
To set user bits
You can record up to eight hexadecimal digits of
information (date, time, clip number, etc.) in the timecode
track.
Carrying Out Recording
1
2
Set CNTR SEL on the HOME page of the function
menu to “UB”.
One recording segment (from the start to the end of
recording) is called a “clip”.
See Chapter 4 “Scene Selection” for more information
about clips.
39
Recording
Download from Www.Somanuals.com. All Manuals Search And Download.
by specifying a number of seconds after the first frame.
The selection range is 0 seconds (0 SEC) to 10 seconds (10
SEC).
1
EJECT
F1
F2
F3
F4
F5
ACCESS
To set shot marks
VAR
MARK1
NETWORK
MENU
CHAPTER
EXPAND
LOCAL
IN
OUT
SUB
CLIP
THUMB
NAIL
REMOTE
LEVEL
SET RESET
JOG
A SHOT MARK1 essence mark or SHOT MARK2
essence mark is set if you hold down the M/MARK1 or m/
MARK2 button and press the SET button during
recording.
PAGE DISPLAY
CLIP
ESSENCE
MARK
MENU
MARK2
PREV
PLAY
NEXT
STOP
TS REC
SHUTTLE
KEY INHI
CH
1
CH
2
CH
3
CH
4
PHONES
PRESET
PB
SHIFT
TOP
END
F
REV
F
FWD
STANDBY
If the unit is set up to display superimposed text
“SHOTMARK2” appears every time you set an essence
mark.
When SHOT MARK1 or SHOT MARK2 essence marks
are set, you can search for the shot marks by displaying
You can also use shot mark positions as edit points during
3 2
1
2
Insert a disc.
Hold down the REC button, and press the PLAY
button.
Recording starts.
3
To stop recording, press the STOP button.
You can also set shot marks during playback. See page 42
for the procedure.
If the disc becomes full
Recording stops and the message “ALARM DISC END.”
appears on the monitor.
Notes
• The shortest clip that can be recorded is 2 seconds long.
Even if recording start and stop operations are performed
within 2 seconds, a 2-second clip is recorded.
• The maximum number of clips that can be recorded is
300. If the loaded disc already contains 300 clips,
recording with the REC button is not possible. (The
message “Disc Full!” appears in the time data display
section.)
• During recording, do not turn off the POWER switch on
the rear panel or disconnect the power cord. This could
cause the clip being recorded to be lost. For details, see
To specify the frame to use as the
thumbnail image
You can display a list of thumbnails of all clips on a disc,
When the unit is shipped from the factory, it is set up to
display the first frame of each clip as the thumbnail. As
required, you can select another frame to display as the
thumbnail.
For example, if there are several seconds of color bars
recorded at the start of the clip, selecting a frame after the
end of the recording of color bars can make it easier to
identify the clip.
You can use META DATA >INDEX POSITION in the
setup menu to select the position of the thumbnail image
40
Recording
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback Operation
Playback
This section describes the following types of playback:
Normal playback: Playback at normal speed
Playback in jog mode: Variable-speed playback, with the
speed determined by the speed of turning the jog dial
Playback in shuttle mode: Variable-speed playback, with
the speed determined by the angular position of the
shuttle dial
This section describes playback of video and audio on the
unit.
Before starting playback, make the following settings and
adjustments.
Selection of time data to display: Select with CNTR SEL
on page P1 of the function menu.
Selection of audio channels to monitor: Select with
MONI CH and MONI SEL on page P1 of the function
menu.
Playback in variable-speed mode: Variable-speed
playback, with the speed finely determined by the
angular position of the shuttle dial
Normal playback
First insert a disc.
Volume adjustment of the monitor audio: Adjust with
the LEVEL knob.
Remote/local setting: Set the remote control switch. If
you set it to REMOTE, also set the setup menu item
INTERFACE SELECT >REMOTE I/F (“REMOTE”
and the connector used appear on the display).
For details of how to insert a disc, see “Loading and
EJECT
Disc playback start position
F1
F2
ACCESS
F3
Although this unit uses optical discs, it is designed to offer
the most convenient features of tape playback by VTRs.
One of these is the playback start position, which works in
the same way as tape, as described below.
VAR
MARK1
NETWORK
LOCAL
MENU
F4
CHAPTER
EXPAND
IN
OUT
SUB
CLIP
THUMB
NAIL
REMOTE
LEVEL
F5
SET RESET
JOG
PAGE DISPLAY
CLIP
ESSENCE
MARK
MENU
MARK2
PREV
PLAY
NEXT
STOP
TS REC
SHUTTLE
KEY INHI
CH
1
CH
2
CH
3
CH
4
PHONES
PRESET
PB
SHIFT
TOP
END
F
REV
F
FWD
STANDBY
After playback stop
The unit stops at the position where the STOP button was
pressed.
Press the PLAY button to resume playback at the stop
position.
PREV button
PLAY button
NEXT button
STOP button
M/MARK1 button and m/MARK2 button
After recording
Jog dial
Shuttle dial
The unit stops at the position where recording ended.
To play back a clip, press the PREV button to move to the
start frame of any clip, or press the PREV button with the
PLAY button held down to move to any position.
To start playback
Press the PLAY button.
Playback starts.
After disc insertion
The unit stops at the position of the disc when it was most
recently ejected.
When two or more clips are recorded on the disc, they are
played back continuously.
Press the PLAY button to resume playback at the most
recent position.
Note
The playback position is saved to the disc when the disc is
ejected, which allows playback to start at that position
whenever it is loaded into any XDCAM player.
No audio is output when non-audio signals are played
back.
To jump to the next or previous clip, then start
playback
Note
Use the PREV button, NEXT button, jog dial, or shuttle
dial.
This function is not available when the Write Inhibit tab of
the disc is set to the recording disabled position, and when
REC INH on page P1 of the function menu is set to “ON”.
The REC INH indicator may light when neither of the
above is true if the format of recorded sections on the disc
is not the same as the recording settings of this unit. In this
case, the playback position can be saved to the disc.
To stop playback
Press the STOP button.
If you play back to the end of the last clip, playback
automatically stops.
If, in this state, you press the PLAY button, the message
“ALARM DISC END.” appears on the display.
41
Playback
Download from Www.Somanuals.com. All Manuals Search And Download.
To carry out playback again, move back to the desired clip
using the PREV button, jog dial or shuttle dial.
EJECT
F1
F2
F3
F4
F5
ACCESS
VAR
MARK1
NETWORK
MENU
CHAPTER
EXPAND
To set shot marks
LOCAL
IN
OUT
SUB
CLIP
THUMB
NAIL
REMOTE
LEVEL
SET RESET
JOG
PAGE DISPLAY
While playing back a disc, you can set essence marks such
as SHOT MARK1 and SHOT MARK2 in desired frames.
To set a SHOT MARK1 or SHOT MARK2, hold down the
M/MARK1 or m/MARK2 button and press the SET
button.
CLIP
ESSENCE
MARK
MENU
MARK2
PREV
PLAY
NEXT
STOP
TS REC
SHUTTLE
KEY INHI
CH
1
CH
2
CH
3
CH
4
PHONES
PRESET
PB
SHIFT
TOP
END
F
REV
F
FWD
STANDBY
3 1 2,3
Note
1
2
Press the SHUTTLE button, turning it on.
To erase or change essence marks, use the supplied
PDZ-1 Proxy Browsing Software.
Turn the shuttle dial to the desired angle
corresponding to the desired playback speed.
Playback in jog mode
Playback in shuttle mode starts.
In jog mode, you can control the speed of playback by the
speed of turning the jog dial. The playback speed range is
–1 to +2 times normal speed.
3
To stop playback in shuttle mode, return the shuttle
dial to the center position, or press the STOP button.
To carry out playback in jog mode, proceed as follows.
Normally, the unit enters shuttle mode as soon as you
turn the shuttle dial.
EJECT
F1
If you want it to enter shuttle mode only when you
press the SHUTTLE button, set OPERATIONAL
FUNCTION >SEARCH ENABLE in the setup menu
to “VIA SEARCH KEY”.
F2
ACCESS
F3
VAR
MARK1
NETWORK
LOCAL
MENU
F4
F5
CHAPTER
EXPAND
IN
OUT
SUB
CLIP
THUMB
NAIL
REMOTE
LEVEL
SET RESET
JOG
PAGE DISPLAY
CLIP
ESSENCE
MARK
MENU
MARK2
PREV
PLAY
NEXT
STOP
TS REC
SHUTTLE
KEY INHI
CH
1
CH
2
CH
3
CH
4
PHONES
PRESET
PB
SHIFT
TOP
END
F
REV
F
FWD
STANDBY
To alternate between normal-speed playback and
shuttle mode playback
Set the shuttle dial to the position corresponding to the
desired shuttle playback speed, then switch between
normal-speed playback and shuttle playback by pressing
the PLAY and SHUTTLE buttons alternately.
1 2,3
1
2
Press the JOG button, turning it on.
Turn the jog dial in the desired direction, at the speed
corresponding to the desired playback speed.
Playback in variable-speed mode
In variable-speed mode, you can control the speed of
playback in the range of –1 to +2 times normal speed.
To carry out playback in variable-speed mode, proceed as
follows.
Playback in jog mode starts.
3
To stop playback in jog mode, stop turning the jog dial.
Normally, the unit enters jog mode as soon as you turn
the jog dial. If you want it to enter jog mode only when
you press the JOG button, set OPERATIONAL
FUNCTION >SEARCH ENABLE in the setup menu
to “VIA SEARCH KEY”.
1
EJECT
F1
F2
ACCESS
F3
VAR
MARK1
NETWORK
LOCAL
MENU
F4
CHAPTER
EXPAND
IN
OUT
SUB
CLIP
THUMB
NAIL
REMOTE
LEVEL
F5
SET RESET
JOG
PAGE DISPLAY
Playback in shuttle mode
In shuttle mode, you can control the speed of playback by
the angular position of the shuttle dial. The range of
playback speed is 20 times normal speed.
CLIP
ESSENCE
MARK
MENU
MARK2
PREV
PLAY
NEXT
STOP
TS REC
SHUTTLE
KEY INHI
CH
1
CH
2
CH
3
CH
4
PHONES
PRESET
PB
SHIFT
TOP
END
F
REV
F
FWD
STANDBY
To carry out playback in shuttle mode, proceed as follows.
3
2,3
1
2
Press the VAR button, turning it on.
Turn the shuttle dial to the desired angle
corresponding to the desired playback speed.
42
Playback
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback in variable-speed mode starts.
In any of the following screens, you can press the
THUMBNAIL button to return to the original screen.
3
To stop playback in variable-speed mode, return the
shuttle dial to the center position, or press the STOP
button.
To select a thumbnail image and start
playback
To alternate between normal-speed playback and
variable-speed mode playback
Set the shuttle dial to the position corresponding to the
desired variable playback speed, then switch between
normal-speed playback and variable-speed mode playback
by pressing the PLAY and VAR buttons alternately.
2
EJECT
F1
F2
ACCESS
F3
VAR
MARK1
NETWORK
LOCAL
MENU
F4
F5
CHAPTER
EXPAND
IN
OUT
SUB
CLIP
THUMB
NAIL
REMOTE
LEVEL
SET RESET
JOG
PAGE DISPLAY
CLIP
ESSENCE
MARK
MENU
MARK2
PREV
PLAY
NEXT
STOP
TS REC
SHUTTLE
KEY INHI
CH
1
CH
2
CH
3
CH
4
PHONES
PRESET
PB
SHIFT
Searching for Clips With Thumbnails
(Thumbnail Search)
TOP
END
F
REV
F
FWD
STANDBY
1
1 1
1
You can display thumbnail images (index pictures) of all
clips on the disc, and use them to cue up a desired clip.
1
2
Do one of the following to select the thumbnail of the
clip you want to cue up.
To display a list of thumbnail images
With the SUB CLIP button off, press the THUMBNAIL
button, turning it on.
A list appears showing thumbnails of 12 clips on the disc,
including the clip being currently played back. (In the
following description, this is referred to as the “thumbnail
screen”.)
• Press the arrow buttons.
• Turn the jog or shuttle dial.
• Press the PREV or NEXT button: Move to the
previous or next thumbnail.
• Press the TOP (SHIFT + PREV) or END (SHIFT +
NEXT) button: Move to the first or last thumbnail.
• Holding down the SHIFT button, press the M/
MARK1 or m/MARK2 button: Display the previous
or next page.
Name of currently
selected clip
Sixth clip is selected from
a total of 34 clips.
a)
Press the SET button or the PLAY button.
Thumbnail (index picture) of
b)
currently selected clip
If you press the SET button, a still image appears
showing the first frame of the selected clip.
If you press the PLAY button, playback starts from the
first frame of the selected clip.
Note
The factory default setting for the clip thumbnail is
such that the first frame of the clip is used as the
thumbnail but you can change this setting so that any
desired frame is used as the clip thumbnail (see “To
the first frame, regardless of the thumbnail.
Total length of selected clip
Recording date and
time of selected clip
Clip information (recording date and time, initial timecode,
total length, and so on)
To change the clip information displayed in
the thumbnail list
With the thumbnail list displayed, proceed as follows.
in double quotation marks, for example “TITLE00001”.
b) A mark is shown to indicate that the thumbnail (index picture) is not the
1
Press the CLIP MENU (SHIFT + SUB CLIP) button
or the MENU button to display the clip menu.
To return to the original screen
Press the THUMBNAIL button, turning it off.
43
Playback
Download from Www.Somanuals.com. All Manuals Search And Download.
2
3
Press the M/MARK1 button or m/MARK2 button to
select CLIP INFORMATION.
Press the SET button.
A list of CLIP INFORMATION items appears.
DATE: Date and time of recording
TIME CODE: Timecode of the first frame in the clip
DURATION: Recording time
SEQUENCE NUMBER: Thumbnail sequence
number
6
7
Press the PLAY button or use the jog or shuttle dial to
play back the clip and display the frame that you want
to use as the thumbnail image.
(page 43) for more information about sequence
thumbnail numbers.
“TIME CODE” is selected when the unit is shipped
from the factory.
To cancel the thumbnail image change
Press the RESET button.
4
Press the M/MARK1 or m/MARK2 button to select an
item that you want to display as part of the clip
information, and then press the SET button.
Press the SET button.
This returns you to the thumbnail list. The specified
image appears as the thumbnail of the selected clip.
A mark is shown to indicate that the thumbnail is not
the first frame of the clip.
The selected item is displayed as clip information
under the thumbnail image.
Mark indicating that the thumbnail is not the first frame
To change a thumbnail image (index
picture)
With the thumbnail list displayed, proceed as follows.
1
2
Press the CLIP MENU (SHIFT + SUB CLIP) button
or the MENU button to display the clip menu.
Press the M/MARK1 button, m/MARK2 button , </
IN button, or ,/OUT button to select SET INDEX
PICTURE.
3
4
Press the SET button.
Note
“SET INDEX” appears in the upper left of the screen.
When you press the SET button or the PLAY button
after selecting a clip with this mark displayed, the clip
is not cued up to the position of the thumbnail. It is
always cued up to the first frame.
Select the clip whose thumbnail you want to change
(you can do this with the same operations as step 1 of
page 43)).
5
Press the SET button.
Searching With the Expand Function
An enlargement of the current thumbnail image
appears.
The expand function allows you to divide a selected clip
into 12 blocks, and to display thumbnails of the first frame
in each block in the thumbnail list. This function is
available whenever the thumbnail list is displayed. This
function allows you to quickly review the content of the
selected clip, and to search efficiently for a target scene.
You can repeat the expand operation up to three times
(t 12 blocks t 144 blocks t 1,728 blocks).
44
Playback
Download from Www.Somanuals.com. All Manuals Search And Download.
Searching for Frames With Essence
Marks
Proceed as follows.
1 3
Note
The maximum number of blocks may be larger than 1728
when the recorded duration of the clip is short. In this case,
the frame interval of expanded thumbnails is fixed at 1
frame. This allows you to view expanded thumbnails at
equal intervals.
EJECT
F1
F2
ACCESS
F3
VAR
MARK1
NETWORK
LOCAL
MENU
F4
F5
CHAPTER
EXPAND
IN
OUT
SUB
CLIP
THUMB
NAIL
REMOTE
LEVEL
SET RESET
JOG
PAGE DISPLAY
CLIP
ESSENCE
MARK
MENU
MARK2
PREV
PLAY
NEXT
STOP
TS REC
SHUTTLE
KEY INHI
CH
1
CH
2
CH
3
CH
4
PHONES
PRESET
PB
SHIFT
TOP
END
F
REV
F
FWD
STANDBY
To execute the expand function
1
2
With the thumbnail list displayed, select the clip that
contains the scene that you want to find.
2 2
1
With the SUB CLIP button off, press the ESSENCE
MARK (SHIFT + THUMBNAIL) button, turning it
on.
Press the EXPAND (F5) button.
The selected clip is divided into 12 blocks, and the first
frame of each block appears in the thumbnail list.
The essence mark selection screen appears.
Number of block
Essence marks not recorded on the disc are displayed
in gray.
3
As required, repeat step 2 once or twice.
To return to the thumbnail list screen
Press the RESET button.
Note
2
3
Press the PREV or NEXT button, or press the M/
MARK1 button or m/MARK2 button, to select the
desired essence mark.
Thumbnails cannot be further divided once their
duration reaches 1 frame.
To return to the thumbnail list screen of the
previous level
Hold down the SHIFT button and press the EXPAND
button.
Press the SET button.
A list appears showing the frames which contain the
selected essence mark.
To return to the thumbnail list screen
Press the RESET button.
4
When you find the thumbnail of the target scene, press
the SET button or the PLAY button.
If you press the SET button, a still image appears
showing the selected frame.
If you press the PLAY button, playback starts from the
selected frame.
45
Playback
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Press the CHAPTER (F4) button.
Indicates that this is a list of
frames containing the essence Sixth frame is selected from a
mark (SHOT MARK1)
total of 36 SHOT MARK1 frames
The CHAPTER screen appears, showing thumbnails
of the frames where the shot marks are set.
“S1” and “S2” marks on thumbnails indicate frames
where SHOT MARK1 and SHOT MARK2 marks are
set.
Frame information (recording date and
time, timecode, or total length)
Thumbnails without a mark are frames where REC
START marks are set.
Currently selected
SHOT MARK1 frame
Recording date and time
of the clip containing the
selected frame
Time from selected shot
mark to next shot mark
3
4
Select the clip whose thumbnail you want to change
(you can do this with the same operations as step 1 of
page 43)).
4
5
Select the clip whose thumbnail you want to change
(you can do this with the same operations as step 1 of
page 43)).
Press the SET button or the PLAY button.
If you press the SET button, a still image appears
showing selected shot mark frame.
If you press the PLAY button, playback starts from the
selected shot mark frame.
Press the SET button or the PLAY button.
If you press the SET button, a still image appears
showing selected essence mark frame.
If you press the PLAY button, playback starts from the
selected essence mark frame.
To delete shot marks at chapter positions
You can delete shot marks (SHOT MARK1 and SHOT
MARK2) at chapter positions in the CHAPTER screen.
(REC START essence marks cannot be deleted.)
Searching With the Chapter
Function
1
With the CHAPTER screen visible, press the CLIP
MENU (SHIFT + SUB CLIP) button or MENU button
to display the clip menu.
When a clip contains shot marks, you can display them as
chapter thumbnails.
2
Select DELETE SHOT MARK.
“DELETE SHOT MARK” appears in the upper left of
the screen.
marks.
3
4
Select the thumbnail image of the shot mark position
to delete.
1
With the thumbnail list visible, select the thumbnail of
the clip that contains the scenes you want.
Press the SET button.
An “S” mark appears in the upper right of the
thumbnails of clips which have shot marks set.
A message appears, asking for confirmation of the
deletion.
“S” mark
5
Press OK to execute the deletion or CANCEL to
cancel it, and then press the SET button.
46
Playback
Download from Www.Somanuals.com. All Manuals Search And Download.
Sixth frame is selected from
a total of 34 sub clips
Clip List Playback
a)
Name of current clip list
Sub clip information (date and
time of creation, initial timecode,
playback time)
You can play back clips in the same order as in a clip list
created using the scene selection function.
See Chapter 4 for more information about scene selection.
Playing back in clip list order
Proceed as follows.
1
If the clip list that you want to play exists on the disc,
load it into the current clip list.
2
3
Press the SUB CLIP button, turning it on.
Press the PLAY button.
Currently selected sub clip
Playback begins from the first sub clip in the current
clip list.
Recording date and time
of clip list
Total playback time of sub
clips in the clip list
a) When a title has been assigned to a clip list, the title is enclosed in double
quotation marks, for example “SAKURA”.
Notes
• Stop the unit before using the SUB CLIP button. Press
the STOP button if a message appears telling you to stop
the unit.
To return to the previous screen
Press the THUMBNAIL button, turning it off.
• Depending on the length of sub clips in the clip list and
their arrangement on the disc, playback may freeze
momentarily between sub clips.
2
3
Select the clip whose thumbnail you want to change
(you can do this with the same operations as step 1 of
page 43)).
To cue up with sub clip thumbnail images
With the desired clip list loaded in the current clip list,
proceed as follows.
Press the SET button or the PLAY button.
If you press the SET button, a still image appears
showing the first frame of the selected sub clip.
If you press the PLAY button, playback starts from the
first frame of the selected sub clip.
1
Press the SUB CLIP button and the THUMBNAIL
button, turning them on.
Thumbnails of the first frames in the sub clips appear.
Note
In clip lists, the first frame of the sub clip (the In point
frame) is always displayed as the thumbnail.
Repeat Playback
You can perform repeat playback for normal and clip list
playback.
To perform repeat playback, set OPERATIONAL
FUNCTION >REPEAT MODE in the setup menu to
“ON” (a REPEAT indicator appears in the display), and
then proceed as follows.
1
Insert a disc.
To perform repeat playback for normal playback,
proceed to step 3.
47
Playback
Download from Www.Somanuals.com. All Manuals Search And Download.
2
3
To perform repeat playback for clip list playback, load
a clip list into the current clip list and then press the
SUB CLIP button.
Notes
• Locked clips are deleted along with other clips.
• Clips cannot be locked or unlocked when the Write
Inhibit tab of the disc is set to the recording disabled
position, or when “REC INH” on the HOME page of the
function menu is set to “ON”.
Press the PLAY button.
Playback starts from the saved playback position.
Normal playback: When playback of the last clip
finishes, it resumes from the start of the disc,
repeatedly playing from the first through the last
clip on the disc.
Clip list playback: When playback of the last sub clip
finishes, it resumes from the start of the clip list,
repeatedly playing from the first through the last
sub clip in the clip list.
1
With the SUB CLIP button off, press the
THUMBNAIL button, turning it on.
The thumbnails of the clips on the disc appear.
2
Select the clip to lock (you can do this with the same
Repeat playback begins the unit is powered on if it is
powered on with a disc loaded and OPERATIONAL
FUNCTION >REPEAT MODE in the setup menu set to
“ON”. Clip list playback starts from the first sub clip in the
clip list.
Clip to be locked
To start repeat playback from the device
connected to the REMOTE (9P) connector
Set OPERATIONAL FUNCTION >REPEAT MODE in
the setup menu to “ON”, and then send the command to
start repeat playback from the external device.
For details of commands, refer to the REMOTE (9-pin)
Protocol Manual for the PDW series (not supplied).
3
Press the MENU button.
The CLIP menu appears.
To stop repeat playback
Do one of the following.
• Set OPERATIONAL FUNCTION >REPEAT MODE in
the setup menu to “OFF”.
• Operate any of the playback buttons except the PLAY
button, or operate the jog or shuttle dial.
• From the external device connected to the REMOTE
(9P) connector on this unit, send a command other than
the repeat playback start command to this unit.
Note
The unit enters search mode when you conduct a search,
and stop mode at the end of the disc.
4
5
Use the V/MARK1 or v/MARK2 button to select
“LOCK/UNLOCK CLIP”, and then press the SET
button.
A lock confirmation screen appears. This screen
displays clip names and clip titles.
Locking (Write-protecting) Clips
In the thumbnail screen, you can lock them so that they
cannot be deleted or altered.
Locking prevents the following operations on clips.
• Deletion
• Renaming by FAM or FTP
• Changing the thumbnail image (index picture)
• Adding and deleting shot marks
To cancel the lock operation and return to the
THUMBNAIL screen
Select “CANCEL”, and then press the SET button.
Press the RESET or MENU button.
With OK selected, press the SET button.
48
Playback
Download from Www.Somanuals.com. All Manuals Search And Download.
You return to the thumbnail screen, and a lock icon
appears on the thumbnail of the selected clip to show
that it is locked.
Notes
• Clips cannot be deleted when the Write Inhibit tab of the
disc is set to the recording disabled position, or when the
function menu item “REC INH” is set to “ON”.
• Locked clips cannot be deleted.
Lock icon
• When the target clip is referenced in a clip list, the clip
list that references the clip will also be deleted.
• If the deletion target clip is referenced by the current clip
list, all of the referenced sub clips, and only those sub
clips, are deleted simultaneously.
Locked clips cannot be deleted or set the thumbnail
image (index picture) and so on. Unlock the clip if you
want to perform any of these operations.
1
With the SUB CLIP button off, press the
THUMBNAIL button, turning it on.
To lock clips with a shortcut operation
After carrying out step 2 in the procedure, press the STOP
button with the SHIFT button held down (shortcut
operation).
The thumbnails of the clips on the disc appear.
2
Select the clip to delete. (You can do this with the same
You can lock clips without displaying the CLIP MENU.
To unlock clips
Clip to be deleted
Carry out step 2 of “Locking clips” to select a locked clip
(one with the lock icon displayed on its thumbnail). Then
do one of the following.
• Carry out steps 3 and 4 of “Locking Clips”.
• Press the STOP button with the SHIFT button held down
(shortcut operation).
To lock all clips
1
2
Carry out steps 1 and 3 of “Locking Clips” to display
the CLIP MENU.
Use the V/MARK1 or the v/MARK2 button to select
LOCK OR DELETE ALL CLIPS, and then press the
b/OUT button.
3
4
Press the MENU button.
The CLIP menu appears.
A submenu screen appears.
Use the V/MARK1 or the v/MARK2 button to select
“DELETE CLIP”, and then press the SET button.
3
4
Select “LOCK ALL CLIPS”, and then press the SET
button.
A deletion confirmation screen appears and then
thumbnails of four frames (the first frame,
intermediate frame 1, intermediate frame 2, and the
last frame) in the target clip appear. At the same time,
the clip name, title, date and time of creation, and
duration appear.
One of the following messages appears, depending on
whether the target clip is referenced in a clip list.
• When the target clip is not referenced in a clip list:
“DELETE CLIP?”
A confirmation screen appears.
With “OK” selected, press the SET button.
All clips are locked.
To unlock all clips
Carry out the procedure in “To lock all clips”, selecting
UNLOCK ALL CLIPS in step 2.
• When the target clip is referenced in a clip list:
“DELETE CLIP & CLIP LIST?” (The clip list that
references the clip will also be deleted.)
Deleting Clips
You can delete selected clips while checking their content.
49
Playback
Download from Www.Somanuals.com. All Manuals Search And Download.
1
With the SUB CLIP button off, press the
THUMBNAIL button, turning it on.
Thumbnails of the clips on the disc appear.
2
3
Press the MENU button.
The CLIP menu appears.
Use the V/MARK1 button to select “CLIP
INFORMATION”, and then press the SET button.
To cancel the deletion and return to the CLIP
MENU
A sub menu appears.
Select “CANCEL”, and then press the SET button.
Press the RESET or MENU button.
5
Use the V/MARK1 button to select “OK”, and then
press the SET button.
The clip is deleted and you return to the thumbnail
screen.
To go to the clip deletion screen without
displaying the CLIP MENU
After step 2, press the RESET button with the SHIFT
button held down (shortcut operation).
The clip deletion screen appears directly, without
displaying the CLIP MENU.
4
Use the v/MARK2 button to select “SEQUENCE
NUMBER”, and then press the SET button.
As shown in the following figure, sequential numbers
are assigned to thumbnails.
To delete all clips
1
2
Carry out steps 1 and 3 of “Deleting Clips” to display
the CLIP MENU.
Use the V/MARK1 or the v/MARK2 buttons to select
“LOCK OR DELETE ALL CLIPS”, and then press
the b/OUT button.
A sub menu appears.
3
4
Select “DELETE ALL CLIPS”, and then press the
SET button.
A deletion confirmation screen appears.
To execute the deletion, use the V button to select
“OK”, and then press the SET button.
All clips are deleted.
However, locked clips are not deleted.
If all clips have been deleted, you return from the
thumbnail screen to the original screen.
Assigning Sequence Numbers to
Thumbnails
You can assign sequence numbers to displayed
thumbnails.
50
Playback
Download from Www.Somanuals.com. All Manuals Search And Download.
Scene Selection
4
Chapter
Overview
What is scene selection?
Scene selection is a function which allows you to select
material (clips) from the material recorded on a disc and
perform cut editing. You can do this by operating on this
unit only.
• Scene selection is a convenient way to perform cut
editing in the field and in other offline situations.
• With the scene selection function, you create clip lists
(edit data). The clips themselves are not changed, so you
can repeat the operation as often as you like.
• Clip lists created with the scene selection function can be
played back on this unit.
• The scene selection function makes it easy to carry out
operations such as adding material in clip units, adding
parts of clips, adding by chapter, reordering the playback
order, modifying In and Out points, and deletion, all on
this unit.
• Clip lists (edit data) created with the scene selection
function can be used on XPRI and other full-feature
nonlinear editing systems.
51
Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
Flow of scene selection editing
Disc
EJECT
Record material or insert disc containing recorded
material into this unit
F1
F2
F3
F4
F5
ACCESS
VAR
MARK1
NETWORK
MENU
CHAPTER
EXPAND
LOCAL
IN
OUT
SUB
CLIP
THUMB
NAIL
REMOTE
LEVEL
SET RESET
JOG
PAGE DISPLA
Y
CLIP
ESSENCE
MARK
MENU
MARK2
PREV
PLAY
NEXT
STOP
TS REC
SHUTTLE
KEY INHI
SHIFT
CH
1
CH
2
CH
3
CH
4
PHONES
PRESET
PB
TOP
F
REV
F
FWD
END
STANDBY
PDW-F330/F350
PDW-F30
To edit a clip list on the disc
Load a clip list (see page 66)
Create and edit a clip list
Sub
Sub Sub
Clip 1
Clip 2 Clip 3 Clip 4
clip 1 clip 2 clip 3
Select
clips
Clip list 1
Recorded material
Clip 1
Clip list 1
Clip 2
Clip 3
Save the clip list to disc (see page 64)
Disc
Sub clip 1 Sub clip 2 Sub clip 3
Play back clip list
EJECT
F1
F2
F3
ACCESS
VAR
MARK1
NETWORK
LOCAL
Play back the clip list (see page 47)
MENU
F4
F5
CHAPTER
EXPAND
IN
OUT
SUB
CLIP
THUMB
NAIL
REMOTE
LEVEL
SET RESET
JOG
PAGE DISPLA
Y
CLIP
ESSENCE
MARK
MENU
MARK2
PREV
PLAY
NEXT
STOP
TS REC
SHUTTLE
KEY INHI
SHIFT
CH
1
CH
2
CH
3
CH
4
PHONES
PRESET
PB
TOP
F
REV
F
FWD
END
STANDBY
PDW-F30
52
Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
Clips
Sub clips (clips in clip lists)
Material recorded with this unit is managed in units called
“clips”. A clip contains the material between a recording
start point and a recording end point.
The specified clips (or parts of clips) in a clip list are called
“sub clips”. Sub clips are virtual data specifying ranges in
the original clips. Clip data in the original clips is not
overwritten. The following figure shows the relation
between clips and sub clips.
Clips have numbers beginning with C, for example C0001.
Recording
start point of Recording end
Clips on disc
clip 2
point of clip 2
r
r
Clip 1
(C0001)
Clip 3
(C0003)
Clip 4
(C0004)
Clip 2 (C0002)
Clip 1
(C0001)
Clip 2
(C0002)
Clip 3
(C0003)
Clip 4
(C0004)
Clip list (E0001)
Sub clip 1
Sub clip 2
Sub clip 3
Clip number
In the above example, the whole of clip 2 has been added
as sub clip 1, and the whole of clip 4 has been added as sub
clip 2.
Sub clip 3 is part of clip 3. Therefore, when clip list E0001
is played back, clip 4 is played after clip 2, and then the
part of clip 3 shown in gray color is played.
Clip list editing (current clip list)
To edit a clip lists, you need to load the clip from the disc
into the internal unit memory.
The clip list which is currently loaded into the unit memory
is called the “current clip list”.
Instead of using clip numbers, you can manage clips by
assigning clip titles.
The current clip list is always the target of sub clip creation
and editing. Clip list playback also uses the current clip
list.
After creating and editing a clip list, you need to save it to
disc.
Clip lists
Data called a “clip list” is created when you use the scene
selection function to select desired clips from the clips
stored on a disc.
Clip lists have numbers beginning with E, for example
E0001. Up to 99 clip lists can be saved on a disc.
Unit memory
Current clip list
Can be edited (adding, deleting, and
reordering sub clips)
t Clip list playback
and thumbnail
display
Clip list number
SAVE Mm LOAD
Disc
C0001 (Clip 1)
C0002 (Clip 2)
E0001 (Clip list 1)
E0002 (Clip list 2)
C0003 (Clip 3)
E0003 (Clip list 3)
•
•
•
•
•
•
E0099 (Clip list 99)
Clip list playback
Thumbnails of sub clips in the selected clip list
Clips and clip lists are saved together on a disc.
Clips are played back according to clip list data.
53
Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
CLIP AUTO TITLING
Assigning Clip Titles
When the setup menu item OPERATIONAL FUNCTION
>CLIP TITLE >AUTO TITLE is set to “ENABLE”, titles
are displayed instead of clip numbers for all clips recorded
after the setting is made.
PREFIX
NUMERIC
_ TITLE
_ 00001
Clip title
SHIFT: ( )( )( )( )KEY
INC/DEC: JOG DIAL
TO MENU: MENU KEY
PREFIX: Prefix (up to 5 alphanumeric characters and
symbols)
NUMERIC: Initial value of the number (00001 to
99999)
2
3
Enter the prefix and initial number.
To select the item to set and the character to set (it
flashes): Use the arrow buttons.
To select a character to enter at the selected
position: Turn the jog dial.
To return the settings to the factory defaults: Press
the RESET button.
Titles are made up of a prefix of up to 10 characters and a
5-digit number. The factory default prefix is “TITLE”, and
the initial value of the number is 00001. Therefore, the title
of the first clip created with the “ENABLE” setting is
“TITLE00001”. The number is incremented for each
subsequent clip.
When you are finished entering the prefix and initial
number, press the SET button.
information about the setup menu.
The message “NOW SAVING...” appears, the title is
saved, and the menu disappears from the screen.
To switch to clip number display
Set CLIP TITLE >AUTO TITLE to “DISABLE”.
Clip numbers are displayed for all clips recorded after the
setting is made.
To clear the menu from the screen without saving a
title
Press the MENU button twice.
Note
Notes
If you return the initial number to the default value after
creating several clips, and then continue recording, clips
with the same titles may be created.
• Titles are displayed instead of clip numbers for clips that
have titles.
page 89) if you want to check the clip number of a clip
that has a title.
Assigning User-Defined Clip and
Clip List Names
To assign clip titles
You can set the clip title prefix and the initial clip title
number to arbitrary values.
For example, if you set the prefix to “SCENE” and the
initial number to 00100, the next clip to be created will
have the title “SCENE-00100”.
The following standard format names are assigned
automatically to clips and clip lists that are created or
recorded by XDCAM devices.
Clips: C0001 to C0300
Clip lists: E0001E01 to E0099E01
You can use the supplied PDZ-1 Proxy Browsing Software
to assign user-defined names instead of the standard
format names. You can assigned user-defined names
instead of the standard format names. Assigning
meaningful names to clips and clip lists can facilitate file
management.
1
Select OPERATIONAL FUNCTION >CLIP TITLE
>TITLE in the setup menu, and then press the ,/
OUT button.
The CLIP AUTO TITLING screen appears.
You can also use this unit's “AUTO TITLING” function to
assign user-defined names to clips.
54
Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
To assign clip names on this unit
The title assigned to clip becomes its clip name (file
name).
Note
When the first letter of the title setting on the CLIP TITLE
menu is a space or period (.), the clip name is the title string
minus the first letter.
To enable clip and clip list renaming by FAM
Carry out step 2 “To assign clip names on this unit”.
It is now possible to write, transfer, and rename clips and
clip lists with user-defined names over file access mode
To change clip names, execute the “Rename” command
for a file in the Clip folder with the extension “.MXF”.
The extension “.MXF” cannot be changed.
C0001.MXF
TITLE00001
When sub item “AUTO NAMING” is set to “C****”
Fuji.MXF
TITLE00001.MXF
Clip renaming by FAM is enabled
TITLE00001
To change clip list names, execute the “Rename”
command for a file in the Edit folder with the extension
“. SMI”.
When sub item “AUTO NAMING” is set to “title”
1
2
Set OPERATIONAL FUNCTION >CLIP TITLE
>AUTO TITLE in the setup menu to “ENABLE” (see
The extension “. SMI” cannot be changed.
Set OPERATIONAL FUNCTION >FILE NAMING
>AUTO NAMING to “free”.
Sakura.SMI
You are now able to use clips and clip lists with user-
defined names.
Clip list renaming by FAM is enabled
To check clip names
3
Set OPERATIONAL FUNCTION >FILE NAMING
>AUTO NAMING to “title”.
Press the THUMBNAIL button to display the thumbnail
screen, and select the clip whose name you want to check.
The name of the selected clip appears at the upper left of
the screen.
However, when a title has been assigned to a clip, display
of the title takes priority. Titles are displayed enclosed in
double quotation marks (“ ”).
C****: Assign standard format clip names
automatically.
title: Assign clip titles as clip names.
SETUP MENU
OPERATIONAL FUNCTION
FILE NAMING
more information about the thumbnail screen.
.
AUTO NAMING title
* C****
title
Note
Clip names, clip list names, and titles are converted as
follows for display in the thumbnail screen and the CLIP
menu.
• If the names are longer than 15 characters, only the first
9 characters and the last 5 characters are displayed.
Other characters are converted into s.
The same name will now be given to newly recorded
clips.
• Lowercase characters are converted into uppercase.
• Kanji and other multibyte characters, and some
alphabetic symbols, are converted into s characters.
55
Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
Sequences of multiple s characters is converted into
single s characters.
The following alphabetic symbols can be displayed.
: . ? ! # * / ( ) + - & @ = < > % " ; _
Creating Clip Lists
Select the desired clip, to include it in the current clip list
as a sub clip.
There are two ways to select clips.
Display example
JumpingDolphin_No103
r
• Select from the thumbnail screen.
JUMPINGDOsNO103
You can select the desired clips from the thumbnail
screen. You can also select continuous clips at a time.
In addition, you can use the Expand function to specify
a range to add in a clip or to load and add a clip with a
chapter registered.
• Select while playing back and searching.
You can select the scene to use while viewing the video
(quick scene selection).
Before starting
Insert a disc containing recorded clips into the unit.
Including Clips Selected in the
Thumbnail Screen in the Clip List
SUB CLIP button
THUMBNAIL button
MENU button
CHAPTER button
EXPAND button
SET button
RESET button
EJECT
F1
F2
F3
F4
F5
ACCESS
VAR
MARK1
NETWORK
MENU
CHAPTER
EXPAND
LOCAL
IN
OUT
SUB
CLIP
THUMB
NAIL
REMOTE
LEVEL
SET RESET
JOG
PAGE DISPLAY
CLIP
ESSENCE
MARK
MENU
MARK2
PREV
PLAY
NEXT
STOP
TS REC
SHUTTLE
KEY INHI
CH
1
CH
2
CH
3
CH
4
PHONES
PRESET
PB
SHIFT
TOP
END
F
REV
F
FWD
STANDBY
SHIFT button
PREV button
PLAY button
NEXT button
STOP button
Jog dial
Arrow buttons
(M/MARK1, m/
MARK2, </IN
button, ,/OUT
button)
Proceed as follows.
1
With the SUB CLIP button unlit, press the
THUMBNAIL button, lighting it.
Thumbnails of the clips on the disc appear.
(In the following description, this is referred to as the
“thumbnail screen”. )
56
Creating Clip Lists
Download from Www.Somanuals.com. All Manuals Search And Download.
+NAME: Name of the clip list, or a user-defined name
You can use the supplied PDZ-1 Proxy Browsing
Software to assign titles to clip lists.
4
5
Use the M/MARK1 or m/MARK2 button to select a
clip list number such as E0001, and then press the SET
button.
This returns to the thumbnail screen.
Press the SUB CLIP button.
2
Press the MENU button.
The clip list window appears.
If you selected NEW FILE in step 4, the display shows
the state with no clips loaded as shown below.
Select NEW FILE to create a new clip list.
(If no clip list is loaded in the current clip list, a screen
as shown in step 3 appears.)
6
7
Press the MENU button.
The CLIP menu appears.
3
Use the M/MARK1 or m/MARK2 button to select
LOAD CLIP LIST, and then press the SET button.
A clip list selection screen appears.
For an already created clip list, the details including
the creation date appear, and for an empty clip list,
“NEW FILE” appears.
Display Item types
Press the ,/OUT button to switch the display.
Use the M/MARK1 or m/MARK2 button to select
“ADD”, and then press the SET button.
The scene selection window appears.
(Subsequently, this entire screen is called the “scene
selection window”.)
To select the type of clip list information to display
Press the ,/OUT button.
Each press of the button switches the display in the
order Date >Title >Name.
The following informantion is displayed for display
item types
+DATE: Date and time when the clip list was created
or last modified
+TITLE: Title assigned to the clip list
57
Creating Clip Lists
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Use the arrow buttons or jog dial to select the desired
clip.
Total duration of sub clips in the current clip list
You can also select clips with the following
operations.
Press the PREV or NEXT button: Moves to the
previous or next clip.
Press the PREV or NEXT button with the SHIFT
button held down: Moves to the first or last clip.
Press the M/MARK1 or m/MARK2 button with the
SHIFT button held down: Switches to the
previous or next page. Does not switch when
there is only one page.
Press the </IN button or ,/OUT button with the
SHIFT button held down: Selects continuous
multiple clips.
Cursor (shows insertion
position of next sub clip)
Thumbnails of the sub clips already added to the current clip list
To display the total duration of the current clip list
after the addition of the selected clips
When you press the SHIFT button, the total duration
of the selected clips is displayed, along with the total
duration of the clip list after the addition of the selected
clips. This allows you to check the new total duration
before making the addition.
12Repeat steps 8 to 11 until you have added all of the
desired clips to the current clip list.
You can add the same clip as a sub clip any number of
times.
13When you have finished selecting all the clips you
want, press the SET button without pressing the
SHIFT button.
9
Press the SET button.
An I-shaped cursor appears in the lower part of the
scene selection window.
Press the RESET button to return to the state of step 8.
This closes the scene selection window, and the screen
returns to the CLIP menu.
To close the CLIP menu
Press the RESET button.
10Use the arrow buttons or jog dial to move the I-shaped
cursor to the desired position.
You can also move the I-shaped cursor with the
following operations.
Press the PREV or NEXT button: Moves the cursor
to the previous or next sub clip.
14Save the current clip list to disc.
Press the PREV or NEXT button with the SHIFT
button held down: Moves the cursor to the first
or last sub clip.
Press M/MARK1 or m/MARK2 button: Moves to
the 4th previous or 4th next sub clip.
11With the SHIFT button held down, press the SET
button.
All the clips selected in step 8 are added to the current
clip list as sub clips and the scene selection window
shows thumbnails of registered sub clips.
At the same time, the cursor disappears and you can
select a new clip.
Notes
• Unless the current clip list has been saved to disc, its
contents will be lost when the unit is powered off or the
disc is ejected. After creating a clip list, be sure to save it.
An asterisk (*) appears after the date and time of creation
when a clip list has not been saved to disc.
58
Creating Clip Lists
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Even if you select several thumbnails, they are added to the
clip list as one continuous sub clip.
To add sub clips using the chapter
function
The chapter function allows a thumbnail to be displayed
for each shot mark recorded within a clip.
For details, see Chapter 3 “Searching for Frames With
Asterisk appears when clip list has not been saved to disc.
• Even when a clip whose thumbnail is not the first frame
is added to a clip list, the thumbnail displayed in the clip
list is always the first frame as a thumbnail.
1
(page 56). An “S” mark appears in the upper right of
thumbnails where short marks have been set. Select
one of these thumbnails and press the CHAPTER
button.
To add sub clips using the expand function
You can include a part of a sub clip in the current clip list
by dividing the content of the sub clip into parts and
displaying thumbnails of the parts.
This displays thumbnails of chapters of the specified
clip in the upper portion of the scene selection
window.
For details, see Chapter 3 “Searching With the Expand
Proceed as follows.
1
After carrying out step 8 of the procedure in
button.
Thumbnails of the target clip divided into eight equal
parts appear in the upper portion of the scene selection
window.
2
3
you want to include in the clip list.
To vary the expansion ratio
Each time you press the EXPAND button changes the
ratio through the sequence ×8 t ×64 t ×512.
To return to the previous setting, hold down the SHIFT
button and press the EXPAND button.
The section from the selected thumbnail to the next
thumbnail is included as a sub clip.
Save the current clip list to disc.
To cancel the expand display
Press the RESET button.
You return to the scene selection window.
When you select several chapter thumbnails, they are
added to the clip list as a single sub clip.
2
3
you want to include in the clip list.
Quick Scene Selection (Adding Sub
Clips During Recording, Playback,
or Search)
The section from the selected thumbnail to the next
thumbnail is included as a sub clip.
Save the current clip list to disc.
Before starting, load the clip list to which you want to add
For details, see “Saving the Current Clip List to Disc”
59
Creating Clip Lists
Download from Www.Somanuals.com. All Manuals Search And Download.
In and Out points set by the quick scene selection function.
To reset an In point or Out point
With the </IN button or ,/OUT button held down,
press the RESET button.
4
Holding down the SHIFT button, press the SET
button.
2,3,4 2,3
EJECT
The section between the In point and Out point is
added to the end of the current clip list as a sub clip.
F1
0
0
TCG
EXT
-12
-20
-12
-20
F2
F3
F4
F5
TC MODE
PRESET
-30
-40
-60
-30
-40
-60
ACCESS
RUN MODE
REC RUN
1
2
3
4
VAR
MARK1
+
NETWORK
4CH 16 BIT
3
4
T C / V I T C
V I T C
MENU
CHAPTER
EXPAND
MPEG HD
SP
VITC
1080 60I
COOO1
LOCAL
REM:077M
DF/NDF
NDF
IN
OUT
SUB
CLIP
THUMB
NAIL
REMOTE
LEVEL
SET RESET
JOG
P2
00:00.00:00
PAGE DISPLAY
When you set In and Out points stretching across
several clips
CLIP
ESSENCE
MARK
MENU
MARK2
PREV
PLAY
NEXT
STOP
TS REC
SHUTTLE
KEY INHI
CH
1
CH
2
CH
3
CH
4
PHONES
PRESET
PB
SHIFT
TOP
END
F
REV
F
FWD
STANDBY
One sub clip is created for each of the clips.
Clips recorded on the disc
4
1
1
Clip 1
Clip 2
Clip 3
1
With the SUB CLIP button off, and the clip displayed
in full-screen mode, play back the clip or conduct a
search to find the point that you want to set as the In
point.
In point
Out point
To display the desired clip in full-screen mode
If the thumbnail screen is displayed, use the arrow
buttons or jog dial to select the clip to display in full-
screen mode, and then press the SET button.
Sub clip 1
Sub clip 2
Sub clip 3
5
6
Repeat steps 1 to 4 until you have added all of the clips
you want to the current clip list.
To search
Use the jog and shuttle dials.
Save the current clip list to disc.
2
3
At the point you want to set as the In point, hold down
the </IN button and press the SET button.
An In point is set, and the IN indicator lights.
If the unit is set up to superimpose character
timecode appears.
In the same way, search for the point you want to set
as the Out point, and then hold down the ,/OUT
button and press the SET button.
An Out point is set, and the OUT indicator lights.
If the unit is set up to superimpose character
timecode appears.
To check the In point or Out point
The timecode of the In or Out point that you have set
appears when you press the </IN button or the ,/
OUT button. An image of the In point is cued up if you
hold down the </IN button and press the PREV
button or NEXT button. An image of the Out point is
cued up if you hold down the ,/OUT button and
press the PREV button or NEXT button.
To check the duration
Hold down the </IN button and the ,/OUT button
at the same time.
The duration appears on the screen.
60
Creating Clip Lists
Download from Www.Somanuals.com. All Manuals Search And Download.
You can also select clips with the following
operations.
Press the PREV or NEXT button: Moves to the
previous or next clip.
Editing Clip Lists
Press the PREV or NEXT button with the SHIFT
button held down: Moves to the first or last clip.
Press M/MARK1 or m/MARK2 button with the
SHIFT button held down: Switches to the
previous or next page. Does not switch when
there is only one page.
Press an </IN button or ,/OUT button with the
SHIFT button held down: Selects continuous
multiple clips.
You can select items from CLIP menus, and perform
simple editing operations on clip lists and on sub clips
registered in clip lists.
Basic Operations
1 3,5 2,4
Note
EJECT
F1
0
0
TCG
EXT
-12
-20
-12
-20
F2
F3
F4
F5
TC MODE
PRESET
If you selected “TRIM”, you can select only one sub
clip.
-30
-40
-60
-30
-40
-60
ACCESS
RUN MODE
REC RUN
1
2
3
4
VAR
MARK1
+
NETWORK
4CH 16 BIT
3
4
T C / V I T C
V I T C
MENU
CHAPTER
EXPAND
MPEG HD
SP
VITC
1080 60I
COOO1
LOCAL
REM:077M
DF/NDF
NDF
IN
OUT
SUB
CLIP
THUMB
NAIL
REMOTE
LEVEL
SET RESET
JOG
P2
00:00.00:00
PAGE DISPLAY
CLIP
ESSENCE
MARK
MENU
MARK2
PREV
PLAY
NEXT
STOP
TS REC
SHUTTLE
KEY INHI
CH
1
CH
2
CH
3
CH
4
PHONES
5
6
Press the SET button.
PRESET
PB
SHIFT
TOP
END
F
REV
F
FWD
STANDBY
This allows you to carry out the editing operation
selected from the CLIP menu for the selected sub clip.
4
4
Carry out the selected editing operation.
1
2
In the clip list screen, hold down the MENU button.
For details, see the following pages.
The CLIP menu appears.
Reordering sub clips: Page 61
Trimming sub clips: Page 62
Deleting sub clips: Page 63
Setting the timecode: Page 63
7
Save the edited current clip list to disc.
Reordering Sub Clips
Press the M/MARK1 or m/MARK2 button to select
the edit item you want.
Proceed as follows.
You can carry out the following edit operations.
1
Carry out steps 1 to 5 of the procedure in “Basic
CLIP menu Item
MOVE
Description
Reorder sub clips.
The I-shaped cursor indicating the move destination
appears in the clip list window.
TRIM
Change the In and Out points of
sub clips.
2
Use the arrow buttons or jog dial to move the I-shaped
cursor to the desired position.
DELETE
Delete unnecessary sub clips.
TC PRESET
Set the first timecode of the
current clip list to any value.
You can also move the cursor with the following
operations.
Press the PREV or NEXT button: Moves the cursor
to the previous or next sub clip.
Press the PREV or NEXT button with the SHIFT
button held down: Moves the cursor to the first
or last sub clip.
3
4
Press the SET button.
A screen appears to allow you to select the target sub
clip of the operation. (A timecode setting screen
appears if you have selected TC PRESET.)
Press M/MARK1 or m/MARK2 button with the
Use the arrow buttons or jog dial to select the desired
sub clip.
SHIFT button held down: Switches to the
61
Editing Clip Lists
Download from Www.Somanuals.com. All Manuals Search And Download.
previous or next page. Does not switch when
there is only one page.
Indicates that 2nd sub clip will be moved to position of 7th sub clip.
To cancel the trim and return to the previous
screen
Press the m/MARK2 button to display “OK” (the
background color changes into yellow), and press the
RESET button.
I-shaped cursor showing position to which selected
sub clip will be moved.
2
3
Carry out playback and search to find the new location
of the In point or Out point of the selected sub clip.
To return to the clip list window without moving
any sub clip
Press the RESET button.
At the scene where you want to set a new In or Out
point, hold down the </IN button (to change the In
point) or the ,/OUT button (to change the Out point)
and press the SET button.
3
Press the SET button.
The CLIP MENU appears after the sub clip order
changes.
If you press the SHIFT + SET buttons instead of the
SET button, you return to the state after step 4 in
“Basic Operations”, allowing you to move another sub
clip.
Depending on the button that you pressed, a new In or
Out point is set.
Note
The IN and OUT indicators flash if you set an Out
point with timecode smaller than the In point. If this
occurs, set the correct timecode.
To change both the In and Out points
Carry out steps 2 and 3 for both the In and Out points.
To reset the In or Out point
Hold down the </IN button or ,/OUT button, and
press the RESET button. The In or Out point is
restored to the value it had before the sub clip trim
screen opened.
4
Save the current clip list to disc.
To cue up the In or Out point
The In point is cued up when you hold down the </
IN button and press the PREV button or the NEXT
button.
The Out point is cued up when you hold down the ,/
OUT button and press the PREV button or the NEXT
button.
Modifying the In and Out Points of
Sub Clips (Trimming)
Proceed as follows.
4
5
Once you have set the new In point or Out point, press
the m/MARK2 button to select “OK”.
1
The background color of the OK button changes to
yellow.
The first frame (In point frame) of the selected sub clip
appears. In this state, you can carry out playback and
search all clips on the disc.
Press the SET button.
62
Editing Clip Lists
Download from Www.Somanuals.com. All Manuals Search And Download.
The CLIP MENU appears after the trim is executed.
If you press the SHIFT + SET buttons instead of the
SET button, you return to the state after step 4 in
“Basic Operations”, allowing you execute another
trim.
By default, the start timecode (LTC) for the current clip list
is set to “00:00:00:00”.
To set this to a different value, proceed as follows.
1
6
Save the current clip list to disc.
2).
For details, see “Saving the Current Clip List to Disc”
The timecode setting screen appears.
Deleting Sub Clips
Proceed as follows.
1
To display the total duration of the current clip list
after the addition of the selected clips
When you press the SHIFT button, the total duration
of the selected clips is displayed, along with the total
duration of the clip list after the deletion of the selected
clips. This allows you to check the new total duration
before making the deletion.
The timecode shown in this screen is the current initial
timecode of the current clip list. If a clip list has been
loaded from disc, and timecode has already been set
for that clip list, then that value is displayed.
2
3
Use the </IN and ,/OUT buttons to select the digit
(HOUR, MIN, SEC or FRAME) you want to set.
2
3
Press the SET button.
Use the M/MARK1 and m/MARK2 buttons or jog dial
to display the value you want to set.
The deletion confirmation screen appears.
To cancel the timecode setting
Press the RESET button.
To return to the clip list window without deleting
any sub clip
Press the RESET button.
4
5
When you have finished setting all the digits you want,
press the SET button.
Use the </IN or ,/OUT button to select “OK”, and
then press the SET button.
The starting timecode for the current clip list is set to
the specified LTC value. The count starts from that
value when playback starts.
The CLIP MENU appears after the deletion is
executed.
If you press the SHIFT + SET buttons instead of the
SET button, you return to the state after step 4 in
“Basic Operations”, allowing you to execute another
deletion.
Save the current clip list to disc.
4
Save the current clip list to disc.
The drop-frame or non-drop-frame setting of the current
clip list reflects the setting of the unit at the time when one
of the following operations is performed.
• Adding the first sub clip
For details, see “Saving the Current Clip List to Disc”
• Setting the start timecode
Setting the Start Timecode for the
Current Clip List
Previewing the Edited Clip List
Continuous timecode is used in clip lists, regardless of the
timecode of the parent clips of sub clips. Therefore, you
can set the start timecode for each clip list.
With the SUB CLIP button lit, press the PLAY button.
If you are in the thumbnail screen (the THUMBNAIL
button is lit), playback starts from the beginning of the
selected sub clip.
63
Editing Clip Lists
Download from Www.Somanuals.com. All Manuals Search And Download.
However, if you press the SUB CLIP button to turn it off,
and then press it again to light it, the playback start position
is reset to the start of the clip list.
With the SUB CLIP button lit, press the PLAY button.
You can repeat playback of the current clip list by setting
SET UP >OPERATIONAL FUNCTION >REPEAT
MODE to ON.
Saving the Current Clip
List to Disc
Notes
• Edited clip list data is not saved unless you carry out this
operation. If you are going to use the created or edited
clip list data later on, be sure to save it to disc.
• If the Write Inhibit tab on the disc is set to the recording
disabled position, you cannot save the current clip list to
the disc.
• It may not be possible to record because of some other
reason, for example not enough free capacity on the disc.
2 2,3
EJECT
F1
0
0
TCG
EXT
-12
-20
-12
-20
F2
F3
F4
F5
TC MODE
PRESET
-30
-40
-60
-30
-40
-60
ACCESS
RUN MODE
REC RUN
1
2
3
4
VAR
MARK1
+
NETWORK
4CH 16 BIT
3
4
T C / V I T C
V I T C
MENU
CHAPTER
EXPAND
MPEG HD
SP
VITC
1080 60I
COOO1
LOCAL
REM:077M
DF/NDF
NDF
IN
OUT
SUB
CLIP
THUMB
NAIL
REMOTE
LEVEL
SET RESET
JOG
P2
00:00.00:00
PAGE DISPLAY
CLIP
ESSENCE
MARK
MENU
MARK2
PREV
PLAY
NEXT
STOP
TS REC
SHUTTLE
KEY INHI
CH
1
CH
2
CH
3
CH
4
PHONES
PRESET
PB
SHIFT
TOP
END
F
REV
F
FWD
STANDBY
Proceed as follows.
1
2
Display the CLIP menu.
Use the M/MARK1 or m/MARK2 button to move the
cursor to “SAVE CLIP LIST”, and then press the SET
button.
A list of clip lists appears. The date of creation or the
title is displayed for each clip list.
“NEW FILE” is displayed for clip lists without any
saved data.
To switch between title display and date of creation
display
Press the ,/OUT button.
For details, see “To select the type of clip list
3
Use the M/MARK1 or m/MARK2 button or jog dial to
select the desired clip list, and then press the ,/OUT
button.
The current clip list is saved to disc.
To cancel the save
Press the MENU button.
To assign a title to a clip list
64
Saving the Current Clip List to Disc
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the supplied PDZ-1 Proxy Browsing Software.
For details, see the PDZ-1 online help.
Managing Clip Lists
After you create or edit a clip list, you can use the CLIP
menu to save it to disc, load it from disc into unit memory,
and delete it from the disc.
Displaying the CLIP menu
Hold down the SHIFT button and press the SUB CLIP
button.
In the thumbnail list screen and the clip list screen, you can
display the CLIP menu by pressing the MENU button.
The CLIP menu items you can display and select vary with
the operating state of the unit (see the following table).
Item
Operation (reference page)
CLIP INFORMATION
Select the information displayed
beneath thumbnails (see page
LOAD CLIP LIST
Load a clip list from the disc into
the current clip list (see page
SAVE CLIP LIST
Save the current clip list to disc
DELETE CLIP LIST
SORT CLIP LISTS BY
Delete a clip list from the disc
You can sort the clip lists by
name or date and time of
a)
Change the thumbnail image
(index picture) of a clip (see
SET INDEX PICTURE
a)
Add sub clips to the current clip
list (see page 56)
ADD
b)
Reorder sub clips (see page 61)
MOVE
b)
Change the In point or Out point
of a sub clip (see page 62)
TRIM
b)
Delete unnecessary sub clips
DELETE
b)
Change the start timecode for
the current clip list to a desired
value (see page 63)
TC PRESET
DELETE CLIP
Delete a clip
LOCK/UNLOCK CLIP
Lock or unlock a clip
LOCK OR DELETE ALL Lock or delete all clips
CLIPS
DELETE SHOT MARK
Delete a shot mark
a) Displayed only in operating thumbnail list screen
b) Displayed only in operating the clip list screen
To clear the CLIP menu from the screen
Press the MENU button (or hold down the SHIFT button
and press the SUB CLIP button).
65
Managing Clip Lists
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Use the M/MARK1 or m/MARK2 button to select the
desired clip list, and then press the SET button.
Note
The CLIP menu can handle up to 99 clip lists.
The selected clip list is loaded into the unit as the
current clip list.
To display thumbnails of the loaded current clip
list
Press the THUMBNAIL button and SUB CLIP button,
turning them on.
Changing Displayed Items of
Information on Sub Clips
You can change information displayed in the lower portion
of each thumbnail in the clip list window.
Proceed as follows.
If an unsaved clip list exists in current clip list
memory
A warning message like the following appears.
“CLIP LIST IS NOT SAVED. OVERWRITE CLIP
LIST?”
Press the </IN button or ,/OUT button to select “OK”
(overwrite) or “CANCEL” (do not overwrite), and then
press the SET button.
1
2
Display the CLIP menu.
Use the M/MARK1 or m/MARK2 button to select
“CLIP INFORMATION”, and then press the SET
button.
A screen appears allowing you to select information
items to display.
Deleting Clip Lists From a Disc
Proceed as follows.
3
Use the M/MARK1 or m/MARK2 button to select the
items you want to display, and then press the SET
button.
1
2
Use the M/MARK1 or m/MARK2 button to select
“DELETE CLIP LIST”, and then press the SET
button.
DATE: Date and time of creation
TIME CODE: Timecode of the start of the sub clip
DURATION: Playback time
SEQUENCE NUMBER: Thumbnail sequence
number
3
4
Use the M/MARK1 or m/MARK2 button to select a
(page 50) for more information about sequence
thumbnail numbers.
clip list to delete, and then press the SET button.
A deletion confirmation screen appears.
When the clip list window is displayed, the
information of the selected items appears in the lower
portion of each thumbnail.
Press the </IN button or the ,/OUT button to select
OK, and then press the SET button.
To cancel the clip list deletion
Press the RESET button.
Loading a Clip List From a Disc Into
the Current Clip List
The selected clip list is deleted from the disc.
To continue deleting other clip lists
Before you can play back or edit a clip list, you need to
load it from the disc into the current clip list.
Proceed as follows.
After selecting “OK”, press the SET button while holding
down the SHIFT button. The selected clip list is deleted,
and you return to step 3 and can continue deleting clip lists.
1
2
Display the CLIP menu.
Sorting Clip Lists
Use the M/MARK1 or m/MARK2 button to select
“LOAD CLIP LIST”, and then press the SET button.
Proceed as follows to sort the list of existing clip lists by
clip list name or by date of creation.
1
Display the CLIP menu.
66
Managing Clip Lists
Download from Www.Somanuals.com. All Manuals Search And Download.
You can jump to the first clip or last clip by pressing the
PREV or NEXT button with the SHIFT button held down.
2
Use the M/MARK1 or m/MARK2 button to select
“SORT CLIP LISTS BY...”, and then press the SET
button.
A screen like the one shown below appears.
3
4
Use the M/MARK1 or m/MARK2 button to select the
type of sorting.
NAME: Sort in ascending order by clip list name.
DATE: Sort by date of creation, with the newest clip
list first.
Press the </IN button.
Sorting starts on LOAD CLIP LIST screen and so on.
Unused clip lists are excluded from the sort.
If you selected “NAME”:
BY NAME: Indicates sorting by name
If you selected “DATE”:
BY DATE: Indicates sorting by date
67
Managing Clip Lists
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the PDZ-1 Proxy
Browsing Software
When a computer with the PDZ-1 Proxy Browsing
Software installed is connected to this unit, you can
transfer the proxy AV data and metadata files recorded on
a disc to the computer. On the computer side, PDZ-1
enables you to browse the proxy AV data, add or modify
metadata (titles, comments, essence marks, etc.), or create
a clip list.
The modified metadata and the created clip list can then be
written back to the disc loaded in this unit.
System requirements to use the PDZ-1
The following are required to use PDZ-1.
• Computer: PC with Intel Pentium III CPU, at least 1
GHz (installed memory: at least 512 MB)
• Operating system: Microsoft Windows 2000 Service
Pack 4 or higher, or Microsoft Windows XP
Professional Service Pack 1 or higher
• Web browser: Internet Explorer 6.0 Service Pack 1 or
higher
• DirectX: DirectX 8.1b or higher
To install PDZ-1
Insert the supplied CD-ROM (PDZ-1 Proxy Browsing
Software) in the CD-ROM drive of the computer and
execute the Setup.exe file, then follow the installation
instructions.
For details, refer to the ReadMe file on the CD-ROM.
Note
Make sure that the work folder to store the material
transferred from this unit is on a hard disk drive with
adequate free space. The amount of proxy AV data
transferred is up to 2.8 GB per disc (when recording in the
LP format).
For details, see “File Operations in File Access Mode”
68
Using the PDZ-1 Proxy Browsing Software
Download from Www.Somanuals.com. All Manuals Search And Download.
File Operations
5
Chapter
Overview
root a)
INDEX.XML
A remote computer can be connected to this unit and used
to operate on recorded data which has been saved in data
files, such as video and audio data files.
ALIAS.XML b)
DISCMETA.XML
Use FAM (file access mode) for the computer connection.
MEDIAPRO.XML
Clip
Directory Structure
C0001.MXF
The following figure shows the directory structure of discs
visible to a remote computer.
C0001M01.XML
C0002.MXF
Note
C0002M01.XML
C0003.MXF
This structure is not the same as the actual structure
recorded on the disc.
C0003M01.XML
Edit
E0001E01.SMI
E0001M01.XML
E0002E01.SMI
E0002M01.XML
Sub
C0001S01.MXF
C0002S01.MXF
C0003S01.MXF
General
a) Root directory
b) Only when sub item “NAMING FORM” on the SETUP
>OPERATIONAL FUNCTION >FILE NAMING page is set to “free”
69
Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
File Operation Restrictions
This section explains which operations are possible on
files stored in each directory.
Read: Read data sequentially from the start to the end of
the file.
When required, the following operation tables distinguish
reading and writing from partial reading and writing.
Partial read: Read only a part of the data in the file.
Write: Write data sequentially from the start to the end of
the file.
Partial write: Write data to a part of the file only.
Root directory
File name
Content
Operations
Read/Partial read Write/Partial write Rename Create
Delete
INDEX.XML
ALIAS.XML
Contains data for management Yes
of the material on the disc.
No
No
No
No
a)
Contains conversion tables for Yes
assigning user-defined names
to clips and clip lists.
No
No
No
No
b)
DISCMETA.XML Contains metadata to indicate Yes
the disc properties.
Yes
No
No
No
No
No
No
No
MEDIAPRO.XML Contains a list of material on
the disc, basic properties,
related information, and
Yes
information about access
methods.
Other files
Files other than the above
–
No
–
No
–
a) Only when sub item “NAMING FORM” on the SETUP
>OPERATIONAL FUNCTION >FILE NAMING page is set to “free”
b) Only files which can be written by XDCAM
Notes
• Directories cannot be created in the root directory.
• The directories in the root directory (Clip, Edit, Sub, and
General) cannot be deleted or renamed.
Clip directory
File name
Content
Operations
Read/Partial read Write/Partial write Rename Create
Delete
b)
c)
d)
a)
Clip file created by recording
(MXF file)
Yes
No
No
Yes
Yes
*
C .MXF
*: 0001 to 9999
e)
f)
g)
h)
a)
Metadata file generated
automatically when C .MXF file
Yes
Yes
No
No
No
*
C M01.XML
*
is created.
*: 0001 to 9999
Other files
Files other than the above
–
No
–
No
–
a) With firmware version 1.5 and higher, the unit can handle files with user-
defined names in the “C*” part.
b) Possible with firmware version 1.5 and higher.
f) With firmware version 1.5 and higher, when the “C*” part of a C*.MXF
file name is changed, a C*M01.XML file with the same name in the “C*”
part is also changed automatically.
c) Only files which are 2 seconds or longer in length, in a format matching
the format (system frequency) and recording format (MPEG HD/DVCAM
and number of audio channels) of the recorded sections of the disc, and
which can be overwritten by XDCAM.
g) When a C*.MXF file is created, a C*M01.XML file with the same name
in the “C*” part is created automatically.
h) When a C*.MXF file is deleted, the C*M01.XML file with the same name
in the “C*” part is also deleted automatically.
d) Only when the Write Inhibit tab on the disc is set to enable recording and
“REC INH” is set to “OFF”. With firmware version 1.1 and lower, only
the most recently recorded clip may be deleted. With firmware version 1.5
and higher, any clip may be selected and deleted.
e) Only files which can be written by XDCAM
70
Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
- Deletion of clips (except the last recorded clip)
- Locking of clips
Notes
• Directories cannot be created in the Clip directory.
• When the following operations, supported by version 1.5
and higher XDCAM devices, are carried out on a disc,
then it becomes impossible for version 1.4 and lower
XDCAM devices to record new clips or delete existing
clips on that disc. (The only possible operations are
playback and disc formatting.)
• If you attempt to write a C*.MXF file which does not
meet the conditions specified as remark d) on this table
via a FAM connection, a Windows error message
appears to the effect that the file or directory is corrupt
and cannot be read.
- Writing of clips with user-defined names
Edit directory
File name
Content
Operations
Read/Partial read Write/Partial write Rename Create
Delete
b)
c)
d)
e)
a)
Clip list file
*: 0001 to 0099
Yes
Yes
No
Yes
Yes
*
E E01.SMI
b)
f)
g)
h)
a)
Metadata file generated
automatically when E*E01.SMI
file is created.
Yes
Yes
No
No
No
No
*
E M01.XML
*: 0001 to 0099
Other files
Files other than the above
–
No
–
–
a) With firmware version 1.5 and higher, the “E*” part can be changed to a
user-defined name.
g) When an E*E01.SMI file is created, an E*M01.XML file with the same
name in the “E*” part is also generated automatically.
b) Only files which can be written by XDCAM. Partial writing is not
possible.
h) When an E*E01.SMI file is deleted, an E*M01.XML file with the same
name in the “E*” part is also deleted automatically.
c) Possible with firmware version 1.5 and higher.
d) Only files which can be written by XDCAM
e) Only when the Write Inhibit tab on the disc is set to enable recording and
“REC INH” is set to “OFF”.
f) With firmware version 1.5 and higher, when the “E*” part of a *E01.SMI
is changed, an E*M01.XML file with the same name in the “E*” part is
also changed automatically.
Note
Directories cannot be created in the Edit directory.
Sub directory
File name
Content
Operations
Read/Partial read Write/Partial write Rename Create
Delete
b)
c)
d)
a)
Proxy AV data (MXF) file
generated automatically when
a C*.MXF file is created.
*: 0001 to 4999
Yes
No
No
No
No
*
C S01.MXF
Other files
Files other than the above
–
No
–
No
–
a) With firmware version 1.5 and higher, the “C*” part can be changed to a
user-defined name.
d) When a C*.MXF file is deleted, the C*S01.XML file with the same name
in the “C*” part is also deleted automatically.
b) With firmware version 1.5 and higher, when the “C*” part of a C*.MXF
file name is changed, a C*S01. MXF file with the same name in the “C*”
part is generated automatically.
Note
c) When a C*.MXF file is created, a C*S01.XML file with the same name in
the “C*” part is generated automatically.
Directories cannot be created in the Sub directory.
General directory
File name
Content
Operations
Read/Partial read Write/Partial write Rename Create
Delete
a)
b)
Any file
Yes
Yes
Yes
Yes
Yes
71
Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
a) UTF-8 file names can be up to 63 bytes in length. (Depending on the
character type, file names (including extension) may be limited to 21
characters.)
b) Only when the Write Inhibit tab on the disc is set to enable recording and
“REC INH” is set to “OFF”.
File Operations in File
Access Mode
The following directory operations are possible in the
General directory.
• Directory creation (up to 64 levels, including the
General directory)
File access mode operating environment
Operating system requirements for file operations by file
access mode are as follows.
• Deletion and renaming of directories
• Computer operating system: Microsoft Windows
2000 Service Pack 4 or higher, or Microsoft
Windows XP
Notes
• The maximum number of files that can be created on one
disc, including directories, is 5,000.
• File names and directory names can use letters, numbers,
and symbols from the Unicode 2.0 (UTF-8) character
set.
However, the following control characters and
symbols cannot be used.
- Control characters: U+0000 to U+001F, U+007F
- Symbols: ", *, /, :, <, >, ?, \, |
Preparations
Do the following on the remote computer and this unit.
• Install the FAM driver on the remote computer (see the
next item).
• In the setup menu, set INTERFACE SELECT >i.LINK
MODE to “FAM (PC REMOTE)” (see page 85).
1)
To install the FAM driver
Insert the supplied CD-ROM (PDZ-1 Proxy Browsing
Software) in the CD-ROM drive of the computer and
execute the Setup.exe file, then follow the installation
instructions.
1) This is supported from firmware version 1.4. However, the following
character codes cannot be used by FAM connections. U+010000,
U+020000, U+030000, U+040000, U+050000, U+060000, 0U+70000,
U+080000, U+090000, U+0A0000, U+0B0000, U+0C0000, U+0D0000,
U+0E0000, U+0F0000, U+100000
For details, refer to the ReadMe file contained on the CD-
ROM disc.
Making FAM Connections
Proceed as follows.
1
If there is a disc loaded in this unit, put the unit into the
following state.
• Recording, playback, search and other disc
operations: Stopped
• Disc access by DELETE LAST CLIP, DELETE
ALL CLIPS, QUICK FORMAT in the DISC menu,
and so on: Stopped
• MENU button: OFF
• Unsaved current clip list: Save or clear
2
Connect the S400 connector on this unit to the
i.LINK (IEEE1394) connector on the remote
computer, using an i.LINK cable.
72
File Operations in File Access Mode
Download from Www.Somanuals.com. All Manuals Search And Download.
To eject discs from a remote computer
Right click the icon representing this unit in Explorer, and
select “Eject” from the menu which appears.
File data
Transfer of files
Disc recorder (this unit)
Laptop computer, etc.
To exit file operations
F1
F2
Proceed as follows.
F3
ACCESS
VCR
NETWORK
LOCAL
MARK1
MENU
CLIP
F4
F5
IN
OUT
REMOTE
LEVEL
THUMB
NAIL
SET RESET
EDIT
JOG
P
AGE DISPLA
Y
CLIP
ESSENCE
MARK
MENU
MARK2
PREV
PLA
Y
NEXT
STOP
REC
SHUTTLE
CH-1
2
CH
3
CH
4
CH
PHONES
VARIABLE
REC
PRESET
PB
SHIFT
TOP
F
REV
F
FWD
END
Note
Do not disconnect the cable before performing steps 1 to 3.
i.LINK cable (not supplied)
Windows recognizes this unit as a removable disc, and
displays one of the following icons on the remote
computer’s task bar:
1
Do one of the following on the
displayed in the remote computer’s taskbar.
or
icon
• Double click.
• Windows 2000:
• Right click, and select one of the following
commands from the menu which appears.
Windows 2000: Unplug or eject hardware
Windows XP: Safely Remove Hardware
• Windows XP:
The remote computer is now able to perform file
operations when a disc is inserted into this unit.
The “Unplug or Eject Hardware” dialog box
(Windows 2000) or the “Safety Remove Hardware”
dialog box (Windows XP) appears.
Operation limitations during FAM connections
• With the exception of the EJECT button, recording
buttons and playback control buttons are disabled.
• This unit cannot be controlled from any device
connected to an external device connector.
• There is no signal output from this unit, and the message
“PC REMOTE!” appears in the display of this unit and
on the external monitor.
2
3
Select “Sony XDCAM PDW-F30 IEEE 1394 SBP2
Device” and click “Stop”.
The “Stop a Hardware device” dialog appears.
Select “Sony XDCAM PDW-F30 IEEE 1394 SBP2
Device” and click “OK”.
In Windows 2000, a confirmation message appears.
In Windows XP, “Sony XDCAM PDW-F30 IEEE
1394 SBP2 Device” is deleted from the list of
“hardware devices”.
Operating on Files
Proceed as follows.
1
Start Explorer.
This unit can now resume normal operations. (The
limitations described in “Operation limitations during
Check that a drive letter has been assigned to this unit.
(The drive letter will differ depending on the number
of other peripherals connected to the remote
computer.)
4
Disconnect the i.LINK cable as required.
2
Use Explorer to perform file operations on the disc
loaded in this unit.
To make a reconnection
To reconnect after exiting file operations, do one of the
following, depending on whether an i.LINK cable is
connected.
You can operate in the same way that you operate on
local drives and files on network computers.
i.LINK cable is not connected: Connect this unit and a
remote computer with an i.LINK cable.
i.LINK cable is connected: Disconnect the i.LINK cable
from either this unit or the remote computer, wait for
at least 10 seconds, and then reconnect the
disconnected cable.
Notes
• If you power this unit off during an FAM
connection, the data transferred thus far is discarded.
• All file operations are not possible for some types of
files.
The unit is powered off and an i.LINK cable is
connected: Power the unit on.
70).
73
File Operations in File Access Mode
Download from Www.Somanuals.com. All Manuals Search And Download.
To disable FAM connections
Execute one of the procedures described in the previous
connection between this unit and the remote computer. To
disable FAM connections, in the setup menu, set
INTERFACE SELECT >i.LINK MODE to “AV/C” (see
74
File Operations in File Access Mode
Download from Www.Somanuals.com. All Manuals Search And Download.
Menus
6
Chapter
To clear the function menu from the screen
Press the DISPLAY button. The size of the monitor video
section increases.
Function Menu
The function menu provides access to frequently used
settings, such as input video signal selection and timecode
settings.
Menu settings are stored in nonvolatile memory and are
preserved even after the unit is powered off.
To change the setting of a function menu
item
Use the F1 to F5 buttons.
Press the button to the right of each setting item to change
the value of the item. Keep pressing the button until the
value you want appears.
Function Menu Operations
Function Menu Settings
The function menu appears on the LCD panel of this unit.
The following figure shows the buttons used in function
menu operations.
The following tables list the setting items on each page and
describe their setting values.
Monitor video
section
HOME page
F1
0
0
-12
-20
-12
-20
F2
F3
F4
TC MODE
PRESET
-30
-40
-60
-30
-40
-60
Setting item
Description
RUN MODE
REC RUN
F1 to F5 buttons
1
2
3
4
+
4CH 16 BIT
3
4
T C / V I T C
V I T C
F1: CNTR SEL (counter
Selects the time data to display
in the time data display section.
TC: Timecode
MPEG HD
SP
VITC
1080 60I
COOO1
REM:077M
DF/NDF
NDF
selection)
F5
P1
00:00.00:00
PAGE DISPLAY
UB: User bits
COUNTER: Elapsed recording
or playback time
DISPLAY button
PAGE button
Display
F2: MONI CH (monitor
Selects the audio channels to
monitor.
Function Menu
channel)
CH 1/2: Channels 1 and 2
CH 3/4: Channels 3 and 4
To display the function menu
The function menu is made up of the HOME page and
page P1.
If the function menu is not already visible, press the PAGE
button to display it. The most recently accessed function
menu page appears.
The size of the monitor video section changes to the
smallest size when the function menu appears.
To display a different page
Each press of the PAGE button displays the next function
menu page in the order HOME t P1 t HOME…
75
Function Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting item
Description
Setting item
Description
F3: MONI SEL (monitor
Selects the audio monitor
signal output from the AUDIO
MONITOR connector and the
PHONES jack.
STEREO: Assign the channels
selected with MONI CH to
left and right.
F3: RUN MODE
When TCG is set to “INT”, and
TC MODE is set to “PRESET”,
selects the run mode of the
internal timecode generator.
REC RUN: The timecode
generator runs only during
recording.
selection)
MONO L (monaural L
channel): Output one of
the channels selected with
MONI CH.
MONO R (monaural R
channel): Output one of
the channels selected with
MONI CH.
FREE RUN: The timecode
generator runs as long as
the unit is powered on.
F4: TC/VITC
Selects the type of timecode
display in the time data display
section (TC or VITC).
F5: DF/NDF
(only when the system
Use this item to select drop-
frame mode (DF) or non-drop-
frequency is 60I/30P/24P frame mode (NDF).
pulldown)
MIX: Output monaural audio
mixed from the channels
selected with MONI CH.
F4: REC INH (recording
Turns recording inhibit mode
on and off.
inhibit)
ON: Recording inhibit mode on
OFF: Recording inhibit mode
off
F5: CHAR SEL (Character Turns the display of character
information display)
information in the monitor video
section of the LCD panel and
on an external monitor on and
off.
ON: Character information on
OFF: Character information off
LCD: Character information on
for the LCD panel only
Even when ON is selected, you
can forcibly turn off the
superimposition of character
information in HD output by
setting the SETUP MENU
>DISPLAY CONTROL >HD
CHARA item.
Page P1
Setting item
Description
F2: TC MODE (timecode
Selects whether the count
value advances from a preset
initial value, or advances
consecutively from the
timecode of the last frame
recorded on the disc.
PRESET: Advance from a
preset initial value.
mode)
REGEN (regenerate):
Advance consecutively
from the timecode of the
last frame recorded on the
disc.
76
Function Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Press the MENU button.
The system menu appears.
System Menu
SYSTEM MENU
SETUP MENU
TC PRESET
Use the system menu to set up the unit for specific
purposes and conditions. Menu settings are stored in
nonvolatile memory and are preserved even after the unit
is powered off.
DISC MENU
DATE/TIME PRESET
HOURS METER
The system menu is made up of the following five menus.
• Setup menu (SETUP MENU)
• TC preset menu (TC PRESET)
• Disc menu (DISC MENU)
• Date and time preset menu (DATE/TIME PRESET)
• Digital time display menu (HOURS METER)
The entire system menu appears in the monitor video
section and on the external monitor.
An uppercase and lowercase abbreviation of the
selected line only (the line in reverse video) appears in
the time data display section.
This section explains the setup menu and the disc menu.
value (Internal Preset)” in Chapter 3 for more information
about the TC preset menu.
2
3
Press the M/MARK1 or m/MARK2 button to select
SETUP MENU or DISC MENU.
See page 27 “Setting the Date and Time” in Chapter 2 for
more information about the date and time preset menu.
Press the ,/OUT button.
page 89) appears.
See page 94 “Periodic Maintenance” in the appendixes
for more information about the digital time display menu.
SETUP MENU
OPERATIONAL FUNCTION
DISPLAY CONTROL
Displaying the Setup and Disc
Menus
SETUP BANK OPERATION
MENU GRADE
:BASIC
Menus appear in the monitor video section and in the time
data display section. If you have connected an external
monitor, they are also superimposed over the picture
shown on that monitor.
Setup Menu
As shown in the following figure, the setup menu has three
levels.
The top level shows a general classification of the setting
items in the menu. Except for MENU GRADE, the actual
setting items are found on the second or third level.
Setting items are divided into basic items, which are
needed for normal operations, and enhanced items, which
are needed for enhanced operations. In the figures, basic
items are shown in bold characters.
When the unit is shipped from the factory, the setup menu
is configured to display basic items only. To display
enhanced items as well, change the setting of the MENU
GRADE item.
For details, see “Displaying enhanced items” on page 88.
77
System Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Top level
Second level
Third level
OPERATIONAL FUNCTION
REPEAT MODE
SETUP MENU
AUTO EE SELECT
LOCAL ENABLE
REC FORMAT
DISC END
DISC OUT
F. FWD/REW
STOP
STANDBY OFF
CLIP TITLE
AUTO TITLE
TITLE
FILE NAMING
SYSTEM SEL
NAMING FORM
AUTO NAMING
SYSTEM FREQ
UC/J
SEARCH ENABLE
VAR SPD LIMIT
PREROLL TIME
AFTER CUE-UP
23.9P OUTPUT
DISPLAY CONTROL
CHARA. POSITION
CHARA. TYPE
CHARA. VSIZE
DISPLAY INFO
SUB STATUS
MENU DISPLAY
BRIGHTNESS
ALARM
MENU STATUS
HD CHARA
TCG REGEN
TIME CODE
UB BINARY GP.
VITC POS SEL-1
VITC POS SEL-2
PD PRESET
STILL TIMER
DISC PROTECTION
VIDEO CONTROL
INT VIDEO SG
SETUP ADD
CC(F1) BLANK
CC(F2) BLANK
FRAME PB
PROCESS CONTROL
VIDEO GAIN
CHROMA GAIN
CHROMA PHASE
SETUP LEVELa)
UP CONVERT
AUTO SQEEZE
CONV MODE
DETAIL GAIN
DOWN CONVERTER
CONV MODE
DETAIL GAIN
CROSS COLOR
(Continued)
78
System Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Top level
Second level
Third level
AUDIO CONTROL
REC MODE
DATA MODE
LEVEL SELECT
INT AUDIO SG
SHUTTLE MUTING
EDIT POINT
REF LEVEL
OUTPUT LEVEL
DV OUT MODE
INTERFACE SELECT
D-SUB OUTPUT
AUDIO OUTPUT
REMOTE I/F
BAUDRATE
i.LINK MODE
NETWORK ENABLE
WIRELESS RMT
METADATA
INDEX POSITION
STORE OWNER
DATA ITEM OUT
SETUP BANK OPERATION
RECALL BANK1
RECALL BANK2
RECALL BANK3
SAVE BANK 1
SAVE BANK 2
SAVE BANK 3
MENU GRADE
a) BLACK LEVEL when the system frequency is 50I/25P
Setup Menu Items
The purpose and settings of the setup menu items are
described below.
• An asterisk (*) (for example *EE) indicates that a setting
is the factory default.
• Brackets [ ] indicate characters and symbols that appear
in the time data display section.
OPERATIONAL FUNCTION [Operational]: Operation
settings
Description
REPEAT MODE [> REPEAT]: Determine whether or not to
*OFF [>> OFF]: Do not put the unit into repeat playback mode.
ON [>> ON]: Put the unit into repeat playback mode.
put the unit into repeat playback mode.
AUTO EE SELECT [> Auto
EE]: Determine whether
the unit enters E-E mode
or PB mode when audio
and video signals from
DISC OUT [>> DISC OUT]:
*EE [>>> EE]: Output video and audio signals received from
other equipment.
PB [>>> PB]: Suppress video and audio signals.
When no disc is loaded.
F.FWD/REV [>> F.FWD/
EE [>>> EE]: Output video and audio signals received from
REV]: Operations when
other equipment.
other equipment are input.
in fast forward or rewind *PB [>>> PB]: Output playback video. Suppress audio signals.
mode
STOP [>> STOP]: Operations EE [>>> EE]: Output video and audio signals received from
when in stop mode
other equipment.
*PB [>>> PB]: Output a still image.
STANDBY OFF [>> STBY
OFF]: Operations when
in standby-off mode
79
System Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONAL FUNCTION [Operational]: Operation
settings
Description
LOCAL ENABLE [> Local ENA]: Select the buttons that can ALL DISABLE [>> All DIS]: The EJECT button and the
be operated on this unit even when the remote control
switch is set to REMOTE.
buttons in the recording/playback control block cannot be
operated.
*STOP & EJECT [>> STOP&EJ]: Only the STOP button and
EJECT button can be operated.
ALL ENABLE [>> All ENA]: The EJECT button and all of the
buttons in the recording/playback control block can be
operated. The preroll time can be set and time data can be
selected on this unit.
REC FORMAT [> REC format]: Select the recording format
HQ [>> HQ]: 35Mbps
*SP [>> SP]: 25Mbps
LP [>> LP]: 18Mbps
(MPEG-2 compression rate).
DISC END [> Disc End]: Select what the unit should do when GOTO TOP [>> GOTO TOP]: Move to the top of the disc.
the free disc capacity is exhausted during recording.
END STOP [>> END STOP]: Stop at the end of the disc.
*EJECT [>> EJECT]: Eject the disc automatically.
CLIP TITLE [> Clip Title]:
Specify how to assign clip
titles.
AUTO TITLE [>> AT Title]:
*DISABLE [>>> DISABLE]: Do not assign.
Select whether to assign ENABLE [>>> ENABLE]: Assign.
clip titles automatically.
TITLE [>> Title]: Assign
The CLIP AUTO TITLING screen appears.
arbitrary titles.
FILE NAMING [> File Name: NAMING FORM [>> Name
*C**** [>>> C****]: Standard format
free [>>> free]: Enable free format
Specify the clip and clip
list name format
Form]: Specify the clip
and clip list name format
AUTO NAMING[>> AT
Naming]: Specify the
format of the file names
generated when clips are
recorded
*C****: [>>> C****]: Standard format
title [>>> title]: Assign the same name as clip title
SYSTEM SEL [> System
Sel]: Select the system
frequency and area of
use.
SYSTEM FREQ [>> Sys
*60I [>>> 60i]: 59.94i
Freq]: Select the system 50I [>>> 50i]: 50i
frequency.
30P [>>> 30P]: 29.97P
25P [>>> 25P]: 25P
23.98P [>>> 23.98P]: 23.98P
Note
UC/J [>> UC/J]: Select the
UC [>>> UC]: For areas outside Japan
area of use.
*J [>>> J]: For Japan
After changing any of the sub-
items, press the on/standby
switch to power the unit off
(put it into standby), and then
press it again to power the unit
on. The initial settings of the
setup menu as a whole will
change to reflect the settings
made here.
23.9P OUTPUT [>> 23.9P
*23.98PsF [>>> 23.9PsF]: Output as 23.98P.
out]: Select the monitor 2-3 PULL DOWN [>>> 2-3PD]: Output after pulldown
output when the
SYSTEM FREQ is
“23.98P”.
conversion to 59.94i.
SEARCH ENABLE [> Search ENA]: Specify how to put the
*DIAL DIRECT [>> DIAL]: The unit switches to a search mode
when you press the JOG, SHUTTLE, or VAR button, or
when you turn the jog or shuttle dial (except during
recording).
unit into a search mode (jog, shuttle, or variable-speed).
VIA SEARCH KEY [>> via KEY]: The unit switches to a
search mode when you press the JOG, SHUTTLE, or VAR
button.
VAR SPD LIMIT [> VAR limit]: Specify whether to limit the
*OFF [>> OFF]: –1 to +2 times normal speed
ON [>> ON]:0 to +1 times normal speed
speed of variable speed playback
80
System Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONAL FUNCTION [Operational]: Operation
settings
Description
PREROLL TIME [> Preroll]: Set the preroll time.
15 SEC [>> 15 sec] to 0 SEC [>> 0 sec]: The preroll time can
be set in one-second increments to between 0 and 15
seconds.
Factory default setting: 5 SEC [>> 5 sec]
A preroll time of at least 5 seconds is recommended when
using this unit for editing. When an editing control unit such as
the BVE-700A has been connected, this setting is disabled and
the setting on the editing control unit is in effect. Operations
such as preroll time setting and time data switching are also
performed on the editing control unit.
AFTER CUE-UP [> After CUE]: Select the operating mode
*STOP [>> STOP]: Stop mode
STILL [>> STILL]: Output still pictures in search mode.
following cue-up.
DISPLAY CONTROL [Display]: Settings related to display Description
on the LCD panel of this unit and on an external monitor
CHARA. POSITION [> Chara pos]: Specify the position
Make settings while viewing characters on the CHARA.
where characters appear in the monitor video section and POSITION (character position) screen.
on external monitors.
To move characters up or down: Press the M/MARK1 or m/
MARK2 button.
To move characters left or right: Press the </IN or ,/OUT
button.
To return to the top level of the setup menu: Press the
MENU button.
CHARA. TYPE [> Chara type]: Select the type of characters Make settings while viewing characters on the CHARA. TYPE
shown in the monitor video section and on an external
monitor.
(character type) screen.
*WHITE (WITH BKGD): White characters on black
background
BLACK (WITH BKGD): Black characters on white background
WHITE/OUTLINE: White characters with black outline
BLACK/OUTLINE: Black characters with white outline
To return to the top level of the setup menu: Press the
MENU button.
CHARA. VSIZE [> Chara size]: Specify the vertical size of
Specify while viewing the display on the CHARA. VSIZE
character information in the monitor video section and on (character vertical size) screen.
an external monitor.
*×1 [>> ×1]: Standard size
×2 [>> ×2]: 2 times standard size
To return to the top level of the setup menu: Press the
MENU button.
DISPLAY INFO [> DISP info]: Select the content of the
character information shown in the monitor video section
and on an external monitor.
*TIME DATA & STATUS [>> Time&STA]: Time data and the
operating mode of the unit
TIME DATA & UB [>> Time&UB]: Time data and user bits
data. However, when user bits as time data is selected,
user bits data and timecode are both displayed, in that
order.
TIME DATA & CNT [>> Time&CNT]: Time data and elapsed
recording or playback time. However, when recording/
playback time as time data is selected, recording/playback
time and timecode are both displayed, in that order.
TIME DATA & TIME [>> Time&Time]: Time data and VITC
TIME DATA & CLIP [>> Time&Clip]: Time data and clip
number
TIME DATA ONLY [>> Time]: Time data only
Time data is selected with CNTR SEL on the HOME page of
the function menu.
81
System Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
DISPLAY CONTROL [Display]: Settings related to display Description
on the LCD panel of this unit and on an external monitor
SUB STATUS [> Sub status]: Select the supplementary
*OFF [>> OFF]: No supplementary status information
status information shown in the monitor video section and TC MODE [>> TC mode]: Indications of the operating mode of
on an external monitor.
internal timecode generator
REMAIN [>> Remain]: Free capacity on the disc (in minute
units)
CLIP NO [>> Clp No]: Clip number
PLAYBACK REMAIN [>> PB remain]: Time from the current
playback position to the recording end position, displayed
in time data format
For details of supplementary status information displayed on
the monitor when a setting other than OFF is selected, see
Chapter 2.
MENU DISPLAY [> Menu DISP]: Select the type of menu
Select while viewing characters on the MENU DISPLAY
characters shown in the monitor video section and on an screen.
external monitor.
*WHITE (WITH BKGD): White characters on black
background
BLACK (WITH BKGD): Black characters on white background
WHITE/OUTLINE: White characters with black outline
BLACK/OUTLINE: Black characters with white outline
To return to the top level of the setup menu: Press the
MENU button.
BRIGHTNESS [> Brightness]: Adjust the brightness of the
The LCD BRIGHTNESS screen appears.
Factory default setting: *55
display.
more information about how to adjust the brightness.
ALARM [> ALARM]: Select whether to display alarm
OFF [>> OFF]: In general, do not display alarm messages.
However, do display some important alarm messages.
ON(LIMITED) [>> ON(Limit)]: Display a minimum number of
alarm messages.
messages.
*ON [>> ON]: Display all alarm messages.
MENU STATUS [> Menu STAT]: Select whether or not to
*DISABLE [>> DISABLE]: Do not display.
display menu settings in the monitor video section of the ENABLE [>> ENABLE]: Display (only when no disc is loaded
LCD panel and on an external monitor when DISPLAY
CONTROL >DISPLAY INFO is set to “TIME DATA &
STATUS”.
or during disc insertion/ejection).
See “Superimposed Text Information” (page 32) in Chapter 2
for the information that is displayed.
HD CHARA [> HD cha]: Specify whether, when CHAR SEL
OFF [>>OFF]: Forcibly turn off superimposition of text
on the HOME page of the function menu is set to “ON”, to
information.
forcibly turn off superimposition of text information on HD *FUNCTION MENU [>>F-MENU]: Do not forcibly turn off
output.
superimposition of text information. (The setting of CHAR
SEL in the function menu takes priority.)
TIME CODE [Time Code]: Settings related to the timecode Description
generator
TCG REGEN [> TCG regen]: Select the signals to generate *TC & UB [>> TC & UB]: Regenerate both timecode signals
when the timecode generator is set to regenerate mode
(TC MODE on page P1 of the function menu is set to
“REGEN”).
and user bits signals.
TC [>> TC] :Regenerate timecode signals only.
UB [>> UB]: Regenerate user bits signals only.
UB BINARY GP. [> Binary Gp.]: Settings related to the user *000:NOT SPECIFIED [>> 000]: Character set not specified
bits binary group flag.
001:ISO CHARACTER [>> 001]: 8-bit characters conforming
to ISO 646 and ISO 2022
010:UNASSIGNED-1 [>>010]: Undefined
011:UNASSIGNED-2 [>> 011]: Undefined
100:UNASSIGNED-3 [>> 100]: Undefined
101:PAGE/LINE [>> 101]: Multiplex
110:UNASSIGNED-4 [>> 110]: Undefined
111:UNASSIGNED-5 [>> 111]: Undefined
Note
When TCG on page P1 of the function menu is set to anything
other than “INT”, and TC MODE is set to “REGEN”, the user
bits binary flag setting of external timecode is followed.
82
System Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
TIME CODE [Time Code]: Settings related to the timecode Description
generator
VITC POS SEL-1 [> VITC pos-1]: Select a line to insert the
When the system frequency is 60i, 23.98P or 30P
VITC in.
20LINE [>> 20 line] to 12LINE [>> 12 line]: Select any line
from 12 to 20.
Factory default setting: *16 LINE [>> 16 line]
Note
You can insert the VITC signal in two places. To insert it in two
places, set both this item and VITC POS SEL-2.
Note
When the system frequency is 60i, 23.98P, or 30P, the VBID
(Video Blanking ID) receives priority over a selection of
“20LINE”.
When the system frequency is 50i or 25P
22LINE [>> 22 line] to 9LINE [>> 9 line]: Select any line from
9 to 22.
Factory default setting: *19 LINE [>> 19 line] (line 19)
VITC POS SEL-2 [> VITC pos-2]: Select a line to insert the
When the system frequency is 60i, 23.98P or 30P
20LINE [>> 20 line] to 12LINE [>> 12 line]: Select any line
from 12 to 20.
VITC in.
Factory default setting: *18 LINE [>> 18 line]
Note
You can insert the VITC signal in two places. To insert it in two
places, set both this item and VITC POS SEL-1.
Note
When the system frequency is 60i, 23.98P, or 30P, the VBID
(Video Blanking ID) receives priority over a selection of
“20LINE”.
When the system frequency is 50i or 25P
22LINE [>> 22 line] to 9LINE [>> 9 line]: Select any line from
9 to 22.
Factory default setting: *21 LINE [>> 21 line] (line 21)
PD PRESET [> PD preset]: Select the timecode to preset.
24F TC [>> 24F TC]: Preset 24-frame timecode.
30F TC [>> 30F TC]: Preset 30-frame timecode.
The A-frames of pulldown sequences are preset.
DISC PROTECTION [Disc protct]: Settings related to disc Description
protection
STILL TIMER [>> STL timer]: Specify the length of time the 0.5SEC [>>> 0.5 sec] to 30MIN [>>> 30 min]: Select time
unit can be in still image mode before switching to disc
protection mode.
from 16 settings ranging from 0.5 second to 30 minutes.
Factory default setting: *8MIN [>>> 8 min] (8 minutes)
VIDEO CONTROL [Video]: Settings related to video
control
Description
INT VIDEO SG [> Video SG]: Select the test signal to be
*100% COLOR BARS [>> 100% bars]: 100% color bar signal
RAMP(Y/C) [>> Ramp]: Bias signal
output from the internal test signal generator.
GRAY [>> Gray]: Grayscale signal
BLACK BURST [>> BB]: Black burst signal
SETUP ADD [> Setup add]: Select whether to add black
*OFF [>> OFF]: Do not add setup.
ON (ADD) [>> ON]: Add setup.
setup to the composite video output signal.
CC (F1) BLANK [> CC1 blank]: Select whether to suppress *OFF [>> OFF]: Suppress.
the closed caption signal to be superimposed on the 1st
field of the output video signal.
ON [>> ON]: Do not suppress.
Note
When you play back a disc with a recorded closed caption
signal, the closed caption signal is multiplexed into composite
output only.
83
System Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO CONTROL [Video]: Settings related to video
control
Description
CC (F2) BLANK [> CC2 blank]: Select whether to suppress *OFF [>> OFF]: Suppress.
the closed caption signal to be superimposed on the 2nd ON [>> ON]: Do not suppress.
field of the output video signal.
Note
When you play back a disc with a recorded closed caption
signal, the closed caption signal is multiplexed into composite
output only.
FRAME PB [> Frame PB]: Select whether to output fields or *AUTO [>> AUTO]: Output a field image when the format is
frames as still images of video.
interlaced, and output a frame image when the format is
progressive.
FRAME[>> FRAME]: Always output a frame image.
PROCESS CONTROL
[> Proc ctrl]: Separate
adjustment screens
VIDEO GAIN [>> V gain]:
–848 [>>> –848] to 847 [>>> 847]
Factory default setting: *0 [>>> 0]
Adjust the video output
level.
appear for the following
items. Use the jog dial to
make settings, and press
the MENU button to return
from the adjustment
screens to the second
level of the setup menu.
CHROMA GAIN [>> C gain]: –848 [>>> –848] to 847 [>>> 847]
Adjust the chroma output Factory default setting: *0 [>>> 0]
level
CHROMA PHASE [>> C
phase]: Adjust the
chroma phase.
–128 [>>> –128] to 127 [>>> 127]
Factory default setting: *0 [>>> 0]
SETUP LEVEL [>> Setup
–272 [>>> –272] to 271 [>>> 271]
Factory default setting: *0 [>>> 0]
lev]: Adjust setup level.
UP CONVERT [> UP
convert]: Specify
upconvert output.
AUTO SQEEZE [>> Auto
*OFF [>>> OFF]: Do not use.
SQZ]: Select whether to ON [>>> ON]: Use.
use auto squeeze mode.
CONV MODE [>> Conv
mode]: Select the
conversion mode.
*EDGE CROP [>>> Edge Crop]: Edge crop mode
LETER BOX [>>> LetterBox]: Letter box mode
SQEEZE [>>> Squeeze]: Squeeze mode
DETAIL GAIN [>> Detail]:
Select the gain level of
the up converter image
enhancer.
*LOW [>>> Low]: Low
MID [>>> Mid]: Mid
HIGH [>>> High]: High
DOWN CONVERTER [>
Down conv]: Set up the
down converter.
CONV MODE [>> Conv
mode]: Select the
conversion mode.
*EDGE CROP [>> Edge Crop]: Edge crop mode
LETER BOX [>> LetterBox]: Letter box mode
SQEEZE [>> Squeeze]: Squeeze mode
Note
“SQEEZE” (squeeze mode) is
selected automatically during
recording.
DETAIL GAIN [>> Detail]:
Select the gain level of
the down converter
*LOW [>> Low]: Low
MID [>> Mid]: Mid
HIGH [>> High]: High
image enhancer.
CROSS COLOR [>> Cross
col]: Turn cross color
adjustment on or off.
*OFF [>>> OFF]: The image enhancer uses default settings
for cross color.
ON [>>> ON]: The image enhancer adjusts so that there are
fewer cross colors.
AUDIO CONTROL [Audio]: Settings related to audio
control
Description
REC MODE [> REC mode]: Select the audio recording mode. *4ch×16bit [>> 4ch/16bit]: 4-channel, 48-kHz mode
2ch×16bit [>> 2ch/16bit]: 2-channel, 48-kHz mode
84
System Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO CONTROL [Audio]: Settings related to audio
control
Description
LEVEL SELECT
[> Level Sel]
REF LEVEL [>> REF Level]: *–20dB [>>> –20dB]
Specify the reference
level (headroom) for
audio signals recorded to –12dB [>>> –12dB]
–18dB [>>> –18dB]
–16dB [>>> –16dB]
disc.
OUTPUT LEVEL [>> Out
*+4dB [>>> +4dB]
Level]: Select the analog 0dB [>>> 0dB]
audio output reference
level.
–3dB [>>> –3dB]
–6dB [>>> –6dB]
INT AUDIO SG [> Audio SG]: Select the operation of the
SILENCE [>> silence]: Silent signal
*1kHz SINE [>> 1kHz]: 1-kHz, –20 dB FS sine wave signal
internal audio test signal generator.
SHUTTLE MUTING [> Shtl muting]: Set the audio muting
*OFF [>> OFF]: Do not perform muting.
ON [>> FULL]: Perform muting.
conditions during shuttle playback.
EDIT POINT [> Edit Point]: Specify the type of editing for
CUT [>> Cut]: Cut editing (Discontinuity in audio signal may
result at the editing point, causing noise during playback.)
*FADE [>> Fade]: Fade in and fade out
audio signals.
IN
OUT
DV OUT MODE [> DV out mod]: Select the audio output
4ch [>> 4ch]: 12 bit/32 kHz/4ch
*2ch [>> 2ch]: 16 bit/48 kHz/2ch
mode of the S400 connector.
INTERFACE SELECT [Interface]: Settings related to
interfaces
Description
D-SUB OUTPUT [> D-SUB Out]: Select the format of the
XGA(SYSTEM) [>> XGA(SYS)]: Set to XGA monitor output
(according to system frequency).
signal output from the MONITOR connector.
*XGA(60Hz) [>> XGA(60Hz)]: Set to XGA monitor output
(fixed at 60 Hz).
YPbPr [>> YPbPr]: Y/R–Y/B–Y component video signals
AUDIO OUTPUT [> Audio Out]: Select the channels for audio *CH1/CH2 [>> CH1/CH2]: Output channel 1 to the AUDIO
output from the AUDIO OUTPUT 1/3 and 2/4 connectors.
OUTPUT 1/3 connector and channel 2 to the AUDIO
OUTPUT 2/4 connector.
CH3/CH4 [>> CH3/CH4]: Output channel 3 to the AUDIO
OUTPUT 1/3 connector and channel 4 to the AUDIO
OUTPUT 2/4 connector.
REMOTE I/F [> Remote I/F]: Select how to perform remote
control, when the remote control switch is set to
REMOTE.
i.LINK [>> i.LINK]: Use the S400 connector.
*9PIN/RS-232C [>> 9P/232C]: Use either the REMOTE(9P)
connector or the RS232C connector, depending on the
setting of the remote connector selector switch.
9PIN(PARA)[>> Para Run]: Use the REMOTE(9P) connector
to connect several PDW-F30 units and perform remote
control from one of them specified as the parent.
BAUDRATE [> BaudRate]: Select the communications speed *9600 [>> 9600]
(bps) of the RS232C connector.
19200 [>> 19200]
38400 [>> 38400]
57600 [>> 57600]
115200 [>> 115200]
i.LINK MODE [> i.LinkMode]: Select the type of connection *AV/C [>> AV/C]: AV/C connection.
FAM(PC REMOTE) [>> FAM]: FAM connection.
for the S400 connector.
NETWORK ENABLE [> Network En]: Select the positions of *NETWORK [>> Network]: Only when the switch is set to
the remote control switch which enable access to the
network.
“NETWORK”.
NETWORK&RS-422A[>> Net&Rmt]: Only when the switch is
set to “NETWORK”, or when the switch is set to
“REMOTE” and the menu item REMOTE I/F is set to
“9PIN/RS232”.
85
System Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
INTERFACE SELECT [Interface]: Settings related to
interfaces
Description
WIRELESS RMT [> Wireless]: Enable or disable operation
DISABLE [>> DISABLE]: Disable.
*ENABLE [>> ENABLE]: Enable.
from the wireless remote commander.
METADATA [Metadata]: Metadata settings
Description
INDEX POSITION [> Index Pos]: Specify which frame to use 0SEC [>> 0 sec] to 10SEC [>> 10 sec]: The frame at 0
as the thumbnail image (index picture) when recording.
seconds to 10 seconds from the top of the clip, specified in
units of 1 second.
Factory default setting: *0SEC
STORE OWNER [> Ownership]: Create UMID owner
The STORED OWNERSHIP screen appears.
information.
For details, see Appendix “Setting UMID ownership
DATA ITEM OUT [> DATA ITEM]: Specify whether to include OFF [>> OFF]: Do not include VANC packet information in
the information from extracted VANC packets in data
items.
data items.
*ON [>> ON]: Include VANC packet information in data items.
SETUP BANK OPERATION [Setup Bank]: Settings related Description
to menu bank operations
Menu bank: This unit allows three different complete sets of menu settings to be saved in what are termed “menu banks”
numbered 1 to 3.
RECALL BANK 1 [> Recall 1]: Recall menu settings from
Operate with the following procedure.
(1) Select the bank you want to recall, then press the ,/OUT
button.
Message “RECALL OK?” appears.
(2) To recall, press the SET button.
To quit recalling, press the RESET button
menu bank 1.
RECALL BANK 2 [> Recall 2] :Recall menu settings from
menu bank 2
RECALL BANK 3 [> Recall 3]: Recall menu settings from
menu bank 3.
SAVE BANK 1 [> Save 1]: Save current menu settings to
Operate with the following procedure.
(1) Select the bank you want to save, then press the ,/OUT
button.
Message “SAVE OK?” appears.
(2) To save, press the SET button.
To quit saving, press the RESET button.
menu bank 1.
SAVE BANK 2 [> Save 2]: Save current menu settings to
menu bank 2.
SAVE BANK 3 [> Save 3]: Save current menu settings to
menu bank 3.
MENU GRADE [Menu grade]: Selection of menu items to Description
be displayed
Determine whether to display basic items only or both basic
and enhanced items in the monitor video section and the time ENHANCED [>> Enhanced]: Display both basic and
data display section when using the setup menu.
*BASIC [>> Basic]: Display basic items only.
enhanced items.
Menu control buttons
Functions
Setup Menu Operations
M/MARK1 and m/MARK2 These buttons move the
buttons
highlighted cursor up and down
within the current level to select
an item or setting. Hold down
one of these buttons to make
the highlighted cursor move
continuously.
This section explains how to change menu settings.
Buttons used to change settings
Use the following buttons to change menu settings.
</IN and ,/OUT buttons Press the ,/OUT button to go
down one level.
Menu control buttons
Functions
MENU button
• Display and hide the menu.
• Return to the menu from
setting screens.
Press the </IN button to go
up one level.
Hold down one of these
buttons to make the highlighted
cursor move continuously.
86
System Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Example: Screen display when SUB STATUS is
Menu control buttons
Functions
selected
RESET button
• Returns the setting to the
factory default setting.
• Answer “No” to the question.
SETUP MENU
DISPLAY CONTROL
:ON
CHARA.DISPLAY
CHARA.POSITION
CHARA.TYPE
CHARA.VSIZE
DISPLAY INFO
SUB STATUS
MENU DISPLAY
BRIGHTNESS
ALARM
SET button
• Saves the new setting in
memory.
• Answer “Yes” to the question.
:WHITE
:x1
:T&STA
:OFF
Changing the settings of basic items
The factory default setting is to display only the basic
items. To change the settings of basic items, proceed as
follows.
:WHITE
:55%
:ON
4
Press the ,/OUT button.
1
Press the M/MARK1 or m/MARK2 button to select
the required item.
This displays all possible settings for the item selected
in step 3.
Example: Screen display when DISPLAY
CONTROL is selected
SETUP MENU
DISPLAY CONTROL
SETUP MENU
OPERATIONAL FUNCTION
DISPLAY CONTROL
:OFF
SUB STATUS
* OFF
TC MODE
REMAIN
SETUP BANK OPERATION
CLIP NAME
MENU GRADE
:BASIC
5
Press the M/MARK1 or m/MARK2 button to change
the setting of the item.
2
Press the ,/OUT button.
This displays menu level 2 for the menu item selected
in step 1.
Example: Screen display of the second level of the
DISPLAY CONTROL menu
SETUP MENU
DISPLAY CONTROL
:OFF
SUB STATUS
* OFF
TC MODE
REMAIN
CLIP NAME
SETUP MENU
DISPLAY CONTROL
:ON
CHARA.DISPLAY
CHARA.POSITION
CHARA.TYPE
CHARA.VSIZE
DISPLAY INFO
SUB STATUS
MENU DISPLAY
BRIGHTNESS
ALARM
:WHITE
:x1
:T&STA
:OFF
6
7
To change other settings, press the </IN button to
return to the previous screen, then repeat steps 3 to 5
as required.
:WHITE
:55%
:ON
When you have completed the settings, press the SET
button.
Current setting
3
Press the M/MARK1 or m/MARK2 button to select
The message “NOW SAVING...” appears in the
monitor video section, and “Saving...” appears in the
time data display section, while the new settings are
saved in memory.
When the saving operation is completed, the monitor
video section and time data display section return to
their normal indications.
the required item.
For menu items on level 3, press the ,/OUT button
to go to level 3, then press the M/MARK1 or m/
MARK2 button to select the item whose setting you
wish to change.
87
System Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
With this done, when you press the MENU button and the
,/OUT button to display the setup menu, all basic and
enhanced items on menu level 1 appear.
Notes
• If you power off the unit before a save operation is
completed, settings may be lost. Wait until the save
is completed before powering off the unit.
• If, instead of pressing the SET button, you press the
MENU button, the new settings are not saved. The
message “ABORT !” appears in the monitor video
section and “Abort !” in the time data display section
for about 0.5 second, and the system exits the menus.
To change more than one setting, be sure to press the
SET button after making the settings.
SETUP MENU
OPERATIONAL FUNCTION
DISPLAY CONTROL
TIME CODE
DISC PROTECTION
VIDEO CONTROL
AUDIO CONTROL
INTERFACE SELECT
METADATA
SETUP BANK OPERATION
ENHAN
MENU GRADE
Meanings of indications on the menu
screen
Current setting
On-screen indication
Right-pointing arrow (c) at Pressing the ,/OUT button
the right of a menu item switches to the next lower
Meaning
Changing the settings of enhanced items
To change the settings of enhanced items, first carry out
the procedure in the previous section “Displaying
enhanced items” then proceed as follows.
See step 1 of the foregoing menu level or to a setting
selection screen.
operating procedure (see
1
In the setup menu screen, repeat steps 2 to 7 of
“Changing the Settings of Basic Items”, and then use
the </IN, ,/OUT, M/MARK1, m/MARK2 buttons
to select a menu item and change the setting.
Left-pointing arrow (C) at
the left of a menu item
See step 2 of the foregoing menu level.
operating procedure (see
Pressing the </IN button
returns to the previous (higher)
2
When you have completed the settings, press the SET
button.
Character string at the
right of a menu item
Current setting of the menu
item
When shown with a colon (:):
the current setting is the
same as the factory default
setting.
The message “NOW SAVING...” appears in the
monitor video section, and “Saving...” appears in the
time data display section, while the new settings are
saved in memory.
When the saving operation is completed, the monitor
video section and time data display section return to
their normal indications.
See step 2 of the foregoing
operating procedure (see
When shown with a raised
dot (•): the current setting
is different from the factory
default setting.
Returning menu settings to their factory
default settings
After making menu setting changes, to return settings to
their factory default settings (setting initialization), use the
following procedure.
See the next item,
An * (asterisk) in a
Factory default setting
complete list of settings
See step 4 of the foregoing
operating procedure (see
To return a particular setting to its factory default
setting
current setting displayed (in the example, if the factory
default setting has been changed, the current setting will be
TC MODE), proceed as follows.
Displaying enhanced items
The factory default setting is not to display enhanced
items.
To display enhanced items, set the menu item MENU
GRADE to “ENHANCED”, following the procedure in
the previous section “Changing the settings of basic
select “ENHANCED”, then press the SET button to save
the setting in memory.
1
2
Press the RESET button.
“OFF” (factory default setting) is selected.
Press the SET button.
88
System Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
The setting returned to its factory default is saved in
memory as the current setting.
DISC MENU
STATUS
DELETE
FORMAT
To return all settings to their factory default
settings
1
2
Display the setup menu.
Press the RESET button.
A message appears, to confirm whether or not you
wish to return all settings to their factory default
settings.
The disc menu contains the following items. Characters
and symbols inside the brackets [ ] appear in the time data
display section.
Message in the monitor Initialize all items to factory
video section
preset values?
STATUS [Status]
Displays disc or clip status.
Message in the time
data display
Init setup?
DISC [> Disc]: Displays the DISC STATUS screen.
CLIP [> Clip]: Displays the CLIP STATUS screen.
3
Press the SET button.
Note
The message “NOW SAVING...” appears in the
monitor video section, and “Saving...” appears in the
time data display, while the settings of all items are
returned to their factory default settings. These factory
default settings are saved in memory.
The PDZ-1 Proxy Browsing Software allows you to write
TITLE1 and TITLE 2 to the disc, but only TITLE1 appears
here.
DELETE [Delete]
Deletes clips from the disc.
Note
LAST CLIP [> Last Clip]: Deletes the most recently
recorded clip.
ALL CLIP [> All Clip]: Delete all clips. (Clips in the
General directory are not deleted.)
If you power off the unit while settings are being
saved, settings may not be correctly returned to their
factory default settings. Wait until the saving is
completed before powering off the unit.
FORMAT [Format]
Formats a disc.
To abandon the resetting operation
Instead of pressing the SET button, press the RESET
button.
The display returns to the top level of setup menu,
leaving the settings unchanged.
QUICK FORMAT [>Quick Format]: Deletes all
data on the disc, including the contents of the
General directory.
Disc Menu Operations
Disc Menu
Use the disc menu to delete data on discs and to format
discs.
To display the status of the current disc or
clip
Insert a disc, and then proceed as follows.
For the method of displaying the disc menu, see
1
2
Press the M/MARK1 button or m/MARK2 button to
select STATUS.
3
4
Press the ,/OUT button.
Select DISC or CLIP and press the ,/OUT button.
If you selected DISC, the status of the loaded disc
appears.
89
System Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the MENU button.
DISC STATUS
To clear the menu from the screen
Press the MENU button twice.
USER ID:
TITLE :
REMAIN
: 029 min
: 0002 times
To delete all clips
REWRITE
SALVAGE
:
:
OK
OK
FILE SYSTEM
Note
Carrying out the following procedure deletes all clips that
are not locked.
TO MENU :
MENU KEY
If you selected CLIP, the status of the current clip
appears.
Proceed as follows.
CLIP STATUS
1
2
CLIP LIST MODE
Press the M/MARK1 button or the m/MARK2 button
to select DELETE.
:
E0001
E0001
CLIP LIST NEME
TITLE:
:
:
:
:
PDW-F30
10001
RECORD DEVICE
3
4
5
Press the ,/OUT button.
SERIAL
06/3/02
19:54:38
DATE
Select ALL CLIP, then press the ,/OUT button.
TIME
:
MENU KEY
TO MENU
When the message “ALL DELETE OK?” appears,
press the SET button.
When playback or search reaches a new clip, the
display changes to the status of the new clip.
All of the clips on the disc are deleted.
To return to the next highest level
Press the MENU button.
To return to the next highest level without deleting
the clips
Press the RESET button.
To clear the menu from the screen
Press the MENU button twice.
To clear the menu from the screen
Press the MENU button.
To delete the most recent recorded clip
To format a disc
Note
If the clip is locked, it cannot be deleted.
Proceed as follows.
1
2
Press the M/MARK1 button or the m/MARK2 button
to select DELETE.
3
4
Press the ,/OUT button.
The name of the clip to be deleted appears.
Press the SET button.
The clip is deleted, and the number of the deleted clip
appears.
To return to the next highest level without deleting
the clip
90
System Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Option Boards
7
Chapter
Option Boards for
Using the PDBK-101
Enhanced Functionality Network Board (Gigabit
Ethernet)
You can enhance the functionality of this unit by installing
option boards in the option slots.
Installing the PDBK-101 Network Board in slot 1 adds a
network connector ( ) to this unit. This allows you to
connect to a computer or network for high-speed FTP file
transfers. You can also connect the unit to a Web site and
display the unit’s device information (model name, serial
number, system frequency, software version, etc.).
You can install up to two option boards. The boards which
may be installed in each slot differ, as follows.
Slot 1: PDBK-101
Slot 2: PDBK-102
Warning
Improper installation of option boards can result in fire,
electric shock, bodily injury, and damage to equipment in
the vicinity. For safety, always have option boards
installed by a trained technician.
CAUTION
When you connect the unit to a computer or network, use
a shielded-type cable to prevent malfunction due to
radiation noise.
Refer to the operation manual supplied with each board
for information about installing, configuring, and
operating the board.
Computer Connection Example (FTP
Connection)
Contact your Sony dealer regarding installation of option
boards.
The following example shows a connection between this
unit and a laptop computer.
91
Option Boards for Enhanced Functionality / Using the PDBK-101 Network Board (Gigabit Ethernet)
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the PDBK-102
MPEG-TS Input/Output
Board
Laptop computer
To network
connector
With the PDBK-102 MPEG-TS Input/Output Board
installed in option slot 2 of this unit, you can make i.LINK
connections between this unit and video devices
Network cable (not supplied)
1)
complying with the HDV 1080i standard (called “HDV
devices” below), and between this unit and computers to
which HDV devices may be connected. These connections
can be used for input and output of MPEG-2 TS streams.
This allows you to input material shot by HDV camcorders
or the results of editing on a computer, and to record the
input on XDCAM discs. You can also output video and
audio from this unit to HDV devices.
To
network connector (GbE)
EJECT
1) HDV and
are trademarks of Sony Corporation and Victor
F1
F2
Company of Japan, Limited.
ACCESS
F3
VAR
MARK1
NETWORK
LOCAL
MENU
F4
F5
CHAPTER
EXPAND
IN
OUT
SUB
CLIP
THUMB
NAIL
REMOTE
LEVEL
SET RESET
JOG
PAGE DISPLAY
CLIP
ESSENCE
MARK
MENU
MARK2
PREV
PLAY
NEXT
STOP
TS REC
SHUTTLE
KEY INHI
CH
1
CH
2
CH
3
CH
4
PHONES
PRESET
PB
SHIFT
HDV Connection Example
TOP
END
F
REV
F
FWD
STANDBY
PDW-F30
Set the remote control switch to “NETWORK”.
The following example shows a connection between this
unit and an HDV camcorder.
PDW-F30
Notes
EJECT
F1
F2
ACCESS
F3
• Install the PDBK-101 in option slot 1.
VAR
MARK1
NETWORK
LOCAL
MENU
F4
CHAPTER
EXPAND
IN
OUT
SUB
CLIP
THUMB
NAIL
REMOTE
LEVEL
F5
SET RESET
JOG
PAGE DISPLAY
• Make network settings in the network settings menu.
This menu appears only when the PDBK-101 option
board is installed.
CLIP
ESSENCE
MARK
MENU
MARK2
PREV
PLAY
NEXT
STOP
TS REC
SHUTTLE
KEY INHI
CH
1
CH
2
CH
3
CH
4
PHONES
PRESET
PB
SHIFT
TOP
F
REV
F
FWD
END
STANDBY
Refer to the PDBK-101 operation manual for more
information about the network settings menu.
S400 connector (6-pin)
Caution
For safety, do not connect a peripheral device connector
that might have excessive voltage to the network connector
of this unit.
Follow the instructions in this manual when making
connections.
i.LINK cable (not supplied)
HDV camcorder
i.LINK connector (4-pin)
Note
Install the PDBK-102 in option slot 2.
92
Using the PDBK-102 MPEG-TS Input/Output Board
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
temperature inside a car with the windows closed can
easily exceed 50°C (122°F).
• In damp or dusty locations
• Locations where the unit may be exposed to rain
• Locations subject to violent vibration
• Near strong magnetic fields
Important Notes on
Operation
• Close to radio or TV transmitters producing strong
electromagnetic fields.
Use and storage
• In direct sunlight or close to heaters for extended periods
Do not subject the unit to severe shocks
The internal mechanism may be damaged or the body
warped.
To prevent electromagnetic interference from
portable communications devices
The use of portable telephones and other communications
devices near this unit can result in malfunctions and
interference with audio and video signals.
Do not cover the unit while operating
Doing so will cause temperatures to rise inside the unit,
possibly resulting in failure.
It is recommended that the portable communications
devices near this unit be powered off.
After use
Turn off the on/standby switch.
If you plan not to use the unit for a long time, turn off the
POWER switch on the rear panel as well.
About the LCD panel
LCD panels are manufactured with extremely high
precision technology that yields effective pixel rates of
99.99% or higher. However, very rarely, one or more
pixels may be permanently dark or permanently lit in
white, red, blue, or green.
This phenomenon is not a malfunction. Such pixels have
no effect on the recorded data, and the unit may be used
with confidence even if they are present.
Shipping
• Remove the disc before transporting the unit.
• If sending the unit by truck, ship, air or other
transportation service, pack it in the shipping carton of
the unit.
Care of the unit
If the body of the unit is dirty, clean it with a soft, dry cloth.
In extreme cases, use a cloth steeped in a little neutral
detergent, then wipe dry. Do not use organic solvents such
as alcohol or thinners, as these may cause discoloration or
other damage to the finish of the unit.
Condensation
If you move the unit from a very cold place to a warm
place, or use it in a damp location, condensation may form
on the optical pickup. Then, if the unit is operated in this
state, recording and playback may not be performed
properly.
In the event of operating problems
If you should experience problems with the unit, contact
your Sony dealer.
Do the following to prevent this from happening.
• When you move or operate the unit in an environment
where condensation may form, be sure to insert a disc in
advance.
• Whenever you turn on the On/standby switch, check that
the HUMID indicator does not appear on the LCD panel.
Use and storage locations
Store in a level, ventilated place. Avoid using or storing the
unit in the following places.
• In excessive heat or cold (operating temperature range:
5°C to 40°C (41°F to 104°F))
Remember that in summer or in warm climates the
93
Important Notes on Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
If it appears, wait until it disappears before inserting a
disc.
Periodic Maintenance
Digital Hours Meter
The digital hours meter can provide information about the
operational history of the unit. Use the information as a
guide in scheduling periodic maintenance. For periodic
maintenance, contact your Sony dealer.
To display digital hours meter
The digital hours meter appears in both the monitor video
section and time data display section as the digital hours
meter menu of the system menu. It can also be
superimposed on the screen of the external video monitor
To display the digital hours meter, proceed as follows.
1
2
Press the MENU button to display the system menu.
Press the M/MARK1 button or m/MARK2 button,
select the HOURS METER (Hours Meter in the time
data display section), and then press the SET button.
HOURS METER
HOURS
HOURS
HOURS
TIMES
H1
H2
H3
H4
H5
317/
22
317
92
92
114
H1:OPERATION
H2:LASER PARAMETER
H3:SEEK RUNNING
H4:SPINDLE RUNNING
H5:LOADING COUNTER
Display of the digital hours meter
Any of the items can be reset during periodic maintenance
or parts replacement. Resetting items allows you to
roughly determine the timing of next periodic
maintenance.
For display resetting, contact your Sony dealer.
Item name (name between Description
[ ] is name in the time data
display section)
H1: OPERATION [Opr]
Displays the total number of
hours the unit has been
powered on in units of hours.
H2: LASER PARAMETER
This shows the cumulative
light output time for optical
head in units of hours.
[Lasr]
94
Periodic Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
Item name (name between Description
[ ] is name in the time data
display section)
Troubleshooting
H3: SEEK RUNNING[Seek] This shows the cumulative
seek operation time for
optical head in units of
hours.
Alarms
H4: SPINDLE
RUNNING[Spdl]
This shows the cumulative
spindle rotation time in units
of hours.
An alarm (warning message) appears in the time data
display section when an operation is attempted which is
inappropriate for the settings on this unit or the state of the
disc. Both the alarm message and the action to take to
resolve the problem appear in the monitor video section
and on the screen of the external video monitor connected
to the unit.
H5: LOADING
COUNTER[Load]
Display the total number of
times discs have been
loaded in the unit.
To exit from the digital hours meter
Press the MENU button.
Example alarm in time data display section
ALARM
REMOTE MODE IS SELECTED.
SET REMOTE/LOCAL/NETWORK
SWITCH TO LOCAL.
Example alarm in monitor video section
When an alarm is displayed, remove the alarm cause by
following the action to take. If the alarm display does not
disappear, contact your Sony dealer.
Please note that there are some alarms which do not appear
depending on the setting of DISPLAY CONTROL
setup menu operations.
When the unit is powered on
Alarm message in time
data display section
Alarm message in monitor video section
Description/action
MENU Ver. UP
ILL. SETUP!
THE SETUP MENU SOFTWARE HAS BEEN
UPGRADED.
SET THE SETUP MENU ITEMS TO THE
DESIRED SETTINGS.
Reset the settings in the setup menu (see page
77).
INVALID SETTINGS SELECTED IN SETUP
MENU.
SET ITEMS IN THE SETUP MENU TO THE
APPROPRIATE VALUES. CONTACT SERVICE
IF THIS ALARM APPEARS AGAIN AFTER
ABOVE PROCEDURE.
Reset the settings in the setup menu (see page
77). If the same message appears after you
reset the settings, contact your Sony dealer.
Exchg batt!
BATTERY NEEDS REPLACING. PLEASE
CONTACT SERVICE.
The NVRAM battery is exhausted. Contact your
Sony dealer.
95
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
When a disc is inserted
Alarm message in time
data display section
Alarm message in monitor video
section
Description/action
Unknown FS!
UNKNOWN FILE SYSTEM.
PLEASE FORMAT DISC OR EJECT.
No FS!
NO FILE SYSTEM.PLEASE EJECT DISC. Eject the disc.
ILL. Disc!
IRREGULAR DISC IS USED.
USE PROFESSIONAL DISC.
Use a Professional Disc.
Salvage NG!
a)
IRREGULAR DISC IS USED. DVCAM
525/60 CLIP(S) EXIST.
Use another disc.
525/60 Clip
a)
IRREGULAR DISC IS USED. DVCAM
625/50 CLIP(S) EXIST.
625/50 Clip
a)
DISC HAS 4CHx16 BIT CLIP(S).
Change the setting of AUDIO CONTROL >REC
4CHx16 Clip
MENU.
a)
DISC HAS 2CHx16 BIT CLIP(S).
Change the setting of AUDIO CONTROL >REC
2CHx16 Clip
MENU.
No Support!
FORMAT NOT SUPPORTED.
RECORDING AND PLAYBACK IS NOT
POSSIBLE.
A disc in an unsupported recording format is loaded.
Use a disc formatted in the MPEG HD or DVCAM
format.
ILL. Index!
INDEX FILE ERROR.
PLEASE FORMAT DISC OR EJECT.
FORMAT NG!
AUTO FORMATTING WAS NOT
COMPLETED.
Eject the disc and insert it again, or insert another
disc.
DI read err
Read err
CANNOT READ DISC
INFORMATION.PLEASE EJECT DISC.
DRV ADJ err
CANNOT PERFORM AUTO DRIVE
ADJUSTMENT.
a) Displayed only when DISPLAY CONTROL >ALARM is set to “ON” or
“LIMITED”.
During front panel operations
Alarm message in time
data display section
Alarm message in monitor video
section
Description/action
a)
KEY INHIBIT MODE IS SELECTED.
This appears when the KEY INH (SHIFT + DISPLAY)
button is on.
KEY INHI.!
Turn the KEY INH button off.
a)
REMOTE MODE IS SELECTED.
SET REMOTE/LOCAL/NETWORK
SWITCH TO LOCAL.
Set the remote control switch to “LOCAL”.
REMOTE!
a)
NO DISC.
Insert a disc and try again.
No Disc!
REC INHI.!
THE DISC WRITE PROTECT TAB IS SET Set the disc’s Write Inhibit tab to enable recording
TO SAVE.
b)
NO CLIP.
This appears when a playback, search or delete
operation is attempted on a disc with no clips
recorded on it.
No Clip!
Insert a disc with clips recorded on it.
96
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm message in time
data display section
Alarm message in monitor video
section
Description/action
a)
DISC TOP.
This appears if you press the PREV button or conduct
a high-speed reverse search when the unit is stopped
at the start of the disc.
Disc Top!
Use forward search or playback instead.
a)
DISC END.
This appears if you press the NEXT button or conduct
a forward high-speed search when the unit is stopped
at the end of the disc.
Disc End!
Use reverse search or playback instead.
MAX # Files
DISC CANNOT BE RECORDED TO.
FOR MORE RECORDING SPACE,
DELETE CLIPS OR NON-AV DATA.
(GENERAL FILES)
Delete clips or GENERAL files.
DISC CANNOT BE RECORDED TO.FOR Delete unneeded clips, or insert a disc with enough
MORE RECORDING SPACE, DELETE
OTHER CLIP LISTS.
free space.
Disc Full!
DISC FULL.FOR MORE RECORDING,
DELETE SOME CLIPS.
Delete unneeded clips, or insert a disc with enough
free space.
b)
NO MORE SUB CLIPS CAN BE ADDED
TO CLIP LIST.
This appears when an attempt is made to add sub
clips when 300 sub clips have already been
registered.
MAX# SB CLP
Limit the creation of sub clips to 300 or fewer.
b)
DURATION OF ONE CLIP LIST MUST BE This appears when you try to add a sub clip when the
CL OVER DUR
LESS THAN 24 HOURS.
total duration of sub clips in a clip list has already
reached 24 hours.
Create clip lists so that the total duration is within 24
hours.
Run Salvage
EXECUTE SALVAGE PROGRAM.
This appears when recording, E-E display, essence
mark recording, or sub clip addition for quick scene
selection is attempted on a disc that needs to be
salvaged.
a)
COUNTER MODE IS SELECTED.
SET COUNTER SELECT SWITCH TO TC the function menu is set to “COUNTER”, and you try
This appears when CNTR SEL on the HOME page of
CNT mode!
OR UB.
to preset timecode or user bits.
To use timecode or user bits, set CNTR SEL to “TC”
a)
TCG REGEN MODE IS SELECTED.
SET TC PRESET MODE IN FUNCTION
MENU.
This appears when TC MODE on page P1 of the
function menu is set to “REGEN”, and you try to
preset timecode or user bits.
REGEN mode!
a)
TCG RUN MODE IS SET TO REC RUN.
SET TC FREE RUN MODE IN FUNCTION function menu is set to “REC RUN”, and you try to
This appears when RUN MODE on page P1 of the
REC RUN!
MENU.
preset timecode or user bits.
b)
THUMBNAIL(S) CANNOT BE
DISPLAYED DURING RECORDING.
Stop recording and try again.
REC mode!
CANNOT EXECUTE IN REC MODE.
DRIVE MAINTENANCE MENU CANNOT
BE EXECUTED WHILE IN REC MODE.
b)
CLIP LIST IS NOT SELECTED.
This appears when you press the SUB CLIP button
while the clip list on the disc is not loaded into the
current clip list.
No SEL List
a)
CLIP LIST CANNOT LOCATE SPECIFIED This appears when a playback button is pressed with
No SUB CLIP
SUB CLIP(S).
no sub clips in the current clip list.
Playback is not possible when there are no sub clips
in the current clip list.
97
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm message in time
data display section
Alarm message in monitor video
section
Description/action
b)
TO ADD AN ESSENCE MARK, EXIT
FROM SUB CLIP MODE FIRST.
This appears when you press the ESSENCE MARK
(SHIFT + THUMBNAIL) button with the SUB CLIP
SB CLP mode
button lit.
Try again after pressing the SUB CLIP button to turn it
off.
b)
SUB CLIP IS INVALID.
SET APPROPRIATE IN/OUT POINTS.
Set the In and Out points again.
SUB CLIP NG
b)
NO CLIP LIST.
This appears when you try to delete a clip list when
there is no clip list saved on the disc.
Load the disc that contains the clip list you want to
delete.
No List!
b)
STOP ONCE, THEN EXECUTE.
This appears when you press the SUB CLIP button
during clip list playback.
STOP ONCE!
Stop the playback and try again.
No EM space
ESSENCE MARK NOT RECORDED.
NO SPACE AVAILABLE TO RECORD
ESSENCE MARK.
Use the PDZ-1 Proxy Browsing Software to delete
unneeded essence marks.
EM Full!
NO MORE ESSENCE MARKS CAN BE
RECORDED.
Disc Damage
NON-AV Full
DISC CANNOT BE RECORDED TO.
USE ANOTHER DISC FOR RECORDING.
Use another disc.
DISC CANNOT BE RECORDED TO.
FOR MORE RECORDING SPACE,
DELETE CLIPS OR NON-AV DATA.
(GENERAL FILES)
Delete unneeded clips or GENERAL files.
Index File!
UNSUPPORT INDEX FILE.
DISC CANNOT BE RECORDED TO.
Use another disc.
File System
CURRENT VERSION OF THE
SOFTWARE SETS THE DISC WRITE
PROTECTED.
This appears when you insert a disc that can be
played back but not recorded.
Exchange the disc for one with a file system
supported by this unit. Or format the disc (see page
36).
FILE SYSTEM ON THE DISC INHIBITS
WRITING.
a)
LOADING.
This appears if you press a button while a disc is
loading. Wait until the disc has finished loading and
try again.
Loading!
a)
UNLOADING.
This appears if you press a button while a disc is
unloading.
Unloading!
Wait until the disc has finished unloading and try
again.
a) Displayed only when DISPLAY CONTROL >ALARM is set to “ON”.
b) Displayed only when DISPLAY CONTROL >ALARM is set to “ON” or
“LIMITED”.
During recording and editing operations
Alarm message in time
data display section
Alarm message in monitor video
section
Description/action
a)
DISC CANNOT BE RECORDED. HD 60I
or HD 30P CLIP(S) EXIST.
This appears when the system frequency of this unit
does not match that of the loaded disc.
Insert a disc that matches the system frequency, or
change this unit’s system frequency setting (see page
22).
HD 60I/30P
a)
DISC CANNOT BE RECORDED. HD 50I
or HD 25P CLIP(S) EXIST.
HD 50I/25P
a)
DISC CANNOT BE RECORDED. HD
23.98P CLIP(S) EXIST.
HD 23P Disc
98
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm message in time
data display section
Alarm message in monitor video
section
Description/action
a)
INPUT VIDEO SIGNAL DOES NOT
SYNCHRONIZE WITH REF VIDEO
SIGNAL.
Input a reference signal synchronized with this unit’s
system frequency.
ILL. REF!
USE COMMON REFERENCE SIGNAL
OR CONNECT RECORDER REF OUT TO
PLAYER REF IN.
a)
ENCODING DOES NOT SYNCHRONIZE Check the signals being input to this unit.
WITH REF VIDEO.
ILL. REC!
a)
ILLEGAL PLAYBACK.
MEMORY FULL !!
Check the disc being played by this unit.
Check the disc being recorded by this unit.
ILL. PLAY!
a)
MEM. Full!
a)
MEMORY EMPTY !!
NOW RECORDING ...
MEM. Empty!
Recording
Wait for recording to finish.
a) Displayed only when DISPLAY CONTROL >ALARM is set to “ON” or
“LIMITED”.
99
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
During playback
Alarm message in time data
display section
Alarm message in monitor video
section
Description/action
a)
DISC CANNOT BE PLAYED BACK.
USE DISC WITH HD 50I or HD 25P
RECORDING.
This appears when the system frequency of this
unit does not match that of the loaded disc.
Insert a disc that matches the system frequency,
or change this unit’s system frequency setting
525/60 Disc
DISC CANNOT BE PLAYED BACK.
USE DISC WITH HD 23.98P
RECORDING.
DISC CANNOT BE PLAYED BACK.
USE DISC WITH DVCAM 625/50
RECORDING.
a)
DISC CANNOT BE PLAYED BACK.
USE DISC WITH HD 60I or HD 30P
RECORDING.
625/50 Disc
DISC CANNOT BE PLAYED BACK.
USE DISC WITH HD 23.98P
RECORDING.
DISC CANNOT BE PLAYED BACK.
USE DISC WITH DVCAM 525/60
RECORDING.
a)
DISC CANNOT BE PLAYED BACK.
USE DISC WITH HD 50I or HD 25P
RECORDING.
HD 60I/30P
DISC CANNOT BE PLAYED BACK.
USE DISC WITH HD 23.98P
RECORDING.
DISC CANNOT BE PLAYED BACK.
USE DISC WITH DVCAM 625/50
RECORDING.
a)
DISC CANNOT BE PLAYED
BACK.USE DISC WITH HD 60I or HD
30P RECORDING.
HD 50I/25P!
DISC CANNOT BE PLAYED
BACK.USE DISC WITH HD 23.98P
RECORDING.
DISC CANNOT BE PLAYED
BACK.USE DISC WITH DVCAM 525/
60 RECORDING.
a)
DISC CANNOT BE PLAYED BACK.
USE DISC WITH HD 60I or HD 30P
RECORDING.
HD 23P Disc
DISC CANNOT BE PLAYED
BACK.USE DISC WITH HD 50I or HD
25P RECORDING.
DISC CANNOT BE PLAYED
BACK.USE DISC WITH DVCAM 525/
60 RECORDING.
DISC CANNOT BE PLAYED
BACK.USE DISC WITH DVCAM 625/
50 RECORDING.
Disc Error!
DISC ERROR DETECTED.
Use another disc.
a) Displayed only when DISPLAY CONTROL >ALARM is set to “ON” or
“LIMITED”.
100
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
During thumbnail search, scene selection, and clip list operations
Alarm message in monitor Description/action
video section
CANNOT EXPAND CLIP
ANY FURTHER.
The clip cannot be expanded into more blocks.
This appears when the EXPAND button is pressed when the number of block is maximum, or
when the duration of an expanded thumbnail is 1 frame.
SELECTED ESSENCE
MARK
DOES NOT EXIST.
The selected essence mark does not exist.
This appears in the essence mark selection screen when the specified essence mark does not
exist on the disc.
SUB CLIP IS INVALID.
SET APPROPRIATE
IN/OUT POINTS.
The temporal relationship between the specified In and Out points in a TRIM operation (see
page 65) is not correct.
Reset so that the value of the Out point timecode is larger than the value of the In point
timecode.
DURATION OF ONE
CLIP LIST MUST BE
LESS THAN 24 HOURS.
The total duration of the current clip list is greater than 24 hours.
This appears when the total duration of the current clip list exceeds the upper limit of 24 hours as
NO MORE SUB CLIPS
CAN BE ADDED TO
THE CLIP LIST.
The upper limit of sub clips in the current clip list has been exceeded.
This appears when the upper limit of 300 clips in a clip list has been exceed as the result of a
SUB CLIP DOES NOT
EXIST.
There are no sub clips in the current clip list.
This appears when an attempt is made to execute a MOVE, TRIM, DELETE, or TC PRESET
CLIP LIST DOES NOT
EXIST.
There are no clip lists on the disc.
This appears when an attempt is made to execute a DELETE CLIP LIST operation (see page
65) when there are no clip lists on the disc.
MOVE IS INVALID.
REC INHI!
The sub clip cannot be moved.
no sub clip in the current clip list, or when there is only 1.
The disc is write protected.
This appears when an attempt is made to execute an operation that requires recording while the
disc is write protected.
DISC FULL!
The disc is full.
This appears when an attempt is made to execute an operation that requires recording while the
disc is full.
SHOT MARK DOES NOT
EXIST.
The specified shot mark has not been recorded.
This appears when an attempt is made to execute a DELETE SHOT MARK operation on a clip
when the specified shot mark has not been recorded for that clip.
REC START CANNOT
BE DELETED.
REC START cannot be deleted.
This appears when an attempt is made to delete a REC START with a DELETE SHOT MARK
operation. DELETE SHOT MARK can delete only SHOT MARK1 and SHOT MARK2 marks.
CLIP IS LOCKED.
The clip is locked.
This appears when an attempt is made to delete a clip, set the clip thumbnail, or delete a shot
mark when the clip is locked.
ALL CLIPS ARE LOCKED.
All clips are locked.
This appears when an attempt is made to execute a LOCK ALL CLIPS operation when all clips
are already locked.
ALL CLIPS ARE
UNLOCKED.
All clips are unlocked.
This appears when an attempt is made to execute an UNLOCK ALL CLIPS operation when all
clips are already unlocked.
101
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarms relating to sensors and drives
Alarm message in time
data display section
Alarm message in monitor video
section
Description/action
FAN Stopped
DR-FAN Stop
High TEMP!
FAN MOTOR STOPPED.
DRIVE FAN MOTOR STOPPED.
HIGH TEMPERATURE.
HIGH TEMPERATURE IN DRIVE.
Contact your Sony dealer.
Note
The unit will not stop operating, but if you continue to
use it in this state temperatures inside the unit or the
drive will rise, possibly resulting in failure or fire.
Error Messages
About i.LINK
Error codes appear in the time data display when an error
(usually a hardware problem) occurs. In addition, both
error messages and error codes appear in the monitor video
section and on the video monitor connected to the unit.
When an error message appears, follow the instructions in
the error message to resolve the problem.
This section explains the specifications and features of
i.LINK.
What is i.LINK?
i.LINK is a digital serial interface designed to integrate
devices equipped with i.LINK connectors. i.LINK allows
your device to:
Error code
- Perform two-way transmission and reception of data
such as digital audio and digital video signals.
- Control other i.LINK devices.
Error code in time data display section
- Easily connect multiple devices with a single i.LINK
cable.
ERROR
AN ERROR HAS BEEN
DETECTED. INFORM SERVICE
OF FOLLOWING CODE:
Your i.LINK device is capable of connecting to a wide
range of digital AV devices for data transfer and other
operations.
Other advantages include the following feature. When
connected to multiple i.LINK devices, your i.LINK device
can perform data transfer and other operations not only
with the directly connected devices but also with any of the
devices that are connected to those devices. Therefore, you
do not need to be concerned with device connection order.
However, depending on the features and specifications of
the connected devices, you may need to use certain
functions differently, and you may not be able to transfer
data or perform certain operations.
50-010
PRESS EJECT KEY
TO EJECT DISC.
Error code in monitor video section
To Eject Discs With the Unit
Powered Off
i.LINK, a nickname for IEEE 1394 proposed by Sony, is a
trademark supported by many companies worldwide.
IEEE 1394 is an international standard defined by IEEE,
the Institute of Electrical and Electronics Engineers, Inc.
As an emergency measure, disc cartridges can be removed
with the unit powered off. This operation should always be
done by a trained service technician.
Note
The unit can be connected to one device with the i.LINK
cable (DV cable). When you connect with a device that has
two or more i.LINK connectors, refer to the operating
instructions supplied with the connected device.
102
About i.LINK
Download from Www.Somanuals.com. All Manuals Search And Download.
About data transfer speed of i.LINK
i.LINK defines maximum data transfer speeds of
approximately 100, 200 and 400 Mbps that are referred
Specifications
1)
to as S100, S200 and S400 respectively.
The maximum data transfer speed that an i.LINK device
supports is identified on the specifications page of the
operating instructions supplied with the device or near its
i.LINK connector.
When you connect a device that supports different data
transfer speeds, the actual data transfer speeds may be
different from those indicated on the i.LINK connectors.
General
External dimensions (w/h/d, excluding projections)
307 × 100 × 411 mm
1
1
(12 / × 4 × 16 / inches)
8
4
1) What is Mbps?
Megabits per second. A measure of the rate at which data
is transmitted per second. In case of 100 Mbps, 100
Megabits of data can be transmitted per second.
i.LINK operation with this unit
For details on operation when other equipment with an
22).
For details on connection with an i.LINK cable and the
necessary software, refer to the operating instructions
supplied with the connected device.
Use Sony i.LINK cables
1
307(12 /8)
Use Sony i.LINK cables to connect the i.LINK devices.
6 pins y 4 pins (For DV dubbing)
6 pins y 6 pins (For DV dubbing)
in mm (inches)
Mass
Power requirements
100 V to 240 V AC, 50/60 Hz
Power consumption
0.79-0.33 A
Peak inrush current
7.2 kg (15 lb 13 oz)
i.LINK and are trademarks.
(1) Power ON, current probe method:
45 A (240 V), 15 A (100 V)
(2) Hot switching inrush current,
measured in accordance with
European standard EN55103-1: 7 A
(230 V)
Operating temperature
5ºC to 40ºC (41ºF to 104ºF)
Storage and transport temperature
–20ºC to +60ºC (–4ºF to +140ºF)
Operating relative humidity (no condensation allowed)
25% to 80% (RH)
Storage and transport relative humidity (no condensation
allowed)
20% to 90%
System
Recording format
Video
Proxy video
Audio
MPEG HD: HQ35/SP25/LP18 Mbps
MPEG-4
MPEG HD: 16 bits, 48 kHz, 4/2 channels
A-law 8 bits, 8 kHz, 4 channels
1)
Proxy audio
103
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback format
Input connectors
Video
MPEG HD: HQ35/SP25/LP18 Mbps
Digital video inputs
i.LINK (HDV 1080i) (with PDBK-102 option board
DVCAM: 25 Mbps
1)
Proxy video
Audio
MPEG-4
installed)
MPEG HD: 16 bits/48 kHz, 4/2 channels
DVCAM: 16 bits/48 kHz, 4 channels
A-law 8 bits, 8 kHz, 4 channels
6-pin type (×1), complying with IEEE
1394
Proxy audio
1) The MPEG-4 Codec is a product of Ingenient Technologies, Inc.
Output connectors
Recording/Playback time (when PFD23 is used)
MPEG HD
Digital video outputs
i.LINK (HDV 1080i) (with PDBK-102 option board
installed)
Mode
HQ mode (VBR 35 65 minutes or
Mbps) more
SP mode (CBR 25 Approx. 85
Mbps) minutes
LP mode (VBR 18 112 minutes or
Mbps) more
4-channel audio 2-channel audio
6-pin type, complying with IEEE 1394
68 minutes or
more
Analog video outputs
COMPOSITE OUT
Approx. 90
minutes
BNC type (×1), 1.0 Vp-p, 75 Ω, sync
122 minutes or
more
negative
Phono jack (×1), 1.0 Vp-p, 75 Ω, sync
negative
MONITOR OUT
DVCAM (playback only)
85 minutes
D-sub 15-pin (RGB or YPbPr)
Search speed
Jog mode
Variable-speed mode
–1 to +2 times normal speed
Analog audio outputs
AUDIO OUTPUT 1/3, 2/4
XLR 3-pin, male (×2), +4/0/–3/–6 dBu
(selectable), 600 Ω, balanced
AUDIO MONITOR
–1 to +2 times normal speed
Shuttle mode –20 to +20 times normal speed
Fast forward mode
+20 times normal speed
Phono jack (×2) –∞to +1 dBu/
Fast reverse mode
47 kΩ/unbalanced (L, R, L+R)
–20 times normal speed
PHONES
Stereo phone jack (×1), –∞to –14 dBu,
8 Ω, unbalanced
Video performance
Sampling frequency
Remote control connectors
Y: 74.25 MHz, R–Y/B–Y: 37.125 MHz
8 bits/sample
REMOTE(9P) D-sub 9-pin, female (×1), complying
with RS-422A
Quantization
Compression MPEG2 MP@HL
RS232C
S400
D-sub 9-pin, male (×1)
6-pin (×1), complying with IEEE 1394
Composite output (DV)
Frequency response
Network (with PDBK-101 option board installed)
RJ-45 type (×1)
50I: 0 to 4.8 MHz +1.0/–3.0 dB
1000Base-T: complying with IEEE
802.3ab
100Base-TX: complying with IEEE
802.3u
60I: 0 to 4.2 MHz +1.0/–3.0 dB
53 dB or more
S/N (Y)
Y/C delay
25 ns or less
K-factor (K2T) 2% or less
10Base-T: complying with IEEE 802.3
Audio performance
Sampling frequency
48 kHz
Accessories supplied
Vertical installation stand (2)
Operating Instructions
Quantization
Headroom
16 bits/2 channels or 16 bits/4 channels
20/18/16/12 dB (selectable)
English version (1)
Japanese version (1)
CD-ROM manual (1)
Frequency response
20 Hz to 20 kHz +0.5/–1.0 dB (0 dB at
Infrared remote commander (1)
PDZ-1 Proxy Browsing Software (1)
Warranty Booklet (1)
1 kHz)
Dynamic range 90 dB or more
Distortion
0.05% or less (at 1 kHz)
104
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories not supplied
AC power cord
• For the customers in the U.S.A and Canada
Part number 1-551-812-41 (125 V, 10 A, about 2.4 m)
• For the customers in the United Kingdom
Part number 1-777-823-12 (250 V, 10 A, about 2.0 m)
• For the customers in European countries other than the
United Kingdom
Part number 1-551-631-61 (250 V, 10 A, about 2.0 m)
Protocol Manual (part number 9-968-084-0X)
PDBK-101 Network Board
PDBK-102 MPEG-TS Input/Output Board
Design and specifications are subject to change without
notice.
Notes
• Always make a test recording, and verify that it was
recorded successfully. SONY WILL NOT BE
LIABLE FOR DAMAGES OF ANY KIND
INCLUDING, BUT NOT LIMITED TO,
COMPENSATION OR REIMBURSEMENT ON
ACCOUNT OF FAILURE OF THIS UNIT OR ITS
RECORDING MEDIA, EXTERNAL STORAGE
SYSTEMS OR ANY OTHER MEDIA OR
STORAGE SYSTEMS TO RECORD CONTENT
OF ANY TYPE.
• Always verify that the unit is operating properly
before use. SONY WILL NOT BE LIABLE FOR
DAMAGES OF ANY KIND INCLUDING, BUT
NOT LIMITED TO, COMPENSATION OR
REIMBURSEMENT ON ACCOUNT OF THE
LOSS OF PRESENT OR PROSPECTIVE PROFITS
DUE TO FAILURE OF THIS UNIT, EITHER
DURING THE WARRANTY PERIOD OR AFTER
EXPIRATION OF THE WARRANTY, OR FOR
ANY OTHER REASON WHATSOEVER.
105
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Using UMID Data
Metadata is additional information recorded on discs along
with audio-visual data. It is used to bring greater efficiency
to the flow of operations from material acquisition through
editing, and to make it easier to find and reuse material.
As one of application of metadata, the UMID has been
internationally standardized.
What is a UMID?
A UMID (Unique Material Identifier) is a unique identifier
for audio-visual material defined by the SMPTE 330M-
2003 standard.
A UMID may be either as a 32-byte Basic UMID or an
Extended UMID, which includes an additional 32 bytes of
Source Pack to make a total 64 bytes.
For details, refer to SMPTE 330M.
Extended UMID (64 bytes)
Basic UMID (32 bytes)
Instance
Source Pack (32 bytes)
Spatial
Coordinates
Time/Date
8 bytes
Universal label
12 bytes
L
Material Number
Country Org
User
No.
4 bytes 4 bytes 4 bytes
1
16 bytes
3 bytes
12 bytes
A globally unique ID is automatically recorded for every
clip.
The Extended UMID is metadata that provides additional
information such as location, time/date, company ID and
so on.
The UMID is applied as follows.
Material No.
ID generated when
shooting
Source Pack
Shooting
information (when,
where and who)
Same as the above
Instance No.
Same as the above
Original material: 00 00 00
Copied material: generation number (1 byte)
+ random number (2 byte)
Distinguish between the
original material and copied
material
Material source ID/
detecting material
Metadata pack that
identifies the source of
material unit by defining the
when, where and who of
the material unit with which
it is associated.
Using the Extended UMID
Functions of UMID data
UMID data enables the following:
• Addition of a globally unique ID to every clip of audio-
visual material. The unique ID is used to detect the
material source and to link it with the original source
material.
You have to enter a country code, organization code and
user code. Set the country code referring to the table in ISO
3166, and set the organization code and user code
according to the guidelines of your organization.
For details, see “Setting UMID ownership information”
106
Using UMID Data
Download from Www.Somanuals.com. All Manuals Search And Download.
• Distinguishing between original material and copied
material. 00 is added to the Instance Number for original
material.
About the UMID ownership information
COUNTRY (country code)
Set the country code by entering an abbreviated
alphanumeric string (4-byte alphanumeric string)
according to the values defined in ISO 3166-1.
There are about 240 country codes.
• Recording with UTC time. UTC (coordinated universal
time) is used when recording the UMID. Use of a
universal time system enables uniform management of
source material recorded all over the world.
• Calculation of date differences. Source material is
recorded using modified Julian dates (MJD), which
enables easy calculation of date differences between
different source material items.
Find your own country code on the following web page.
Refer to ISO 3166-1:
http://www.din.de/gremien/nas/nabd/iso3166ma/
codlstp1/en_listp1.html
Setting UMID ownership information
Proceed as follows.
When the country code is less than 4 bytes, the active part
of the code occupies the first part of the 4 bytes and the
remainder must be filled with the space character (20h).
1
Select METADATA >STORE OWNER in the setup
Example: Japan
For Japan, the country code is JP, which is 2 bytes, or JPN,
which is 3 bytes.
Thus, enter the following:
The STORED OWNERSHIP (UMID ownership
information setting) screen appears.
JP_ _
or
STORED OWNERSHIP
JPN _
COUNTRY
ORGANIZATION
USER
_
_
_
where _ represents a space.
ORGANIZATION (organization code)
Enter a 4-byte alphanumeric string for the organization
code.
SHIFT: ( )( )( )( )KEY
INC/DEC: JOG DIAL
TO MENU: MENU KEY
Notes
• There are no problems in recording or playing back
audio-video signals, even if the ORGANIZATION is not
set.
• Organization codes must be acquired by applying to the
SMPTE registration office. When no organization code
has been acquired, it is forbidden to enter an arbitrary
string. As a rule, the code “00” must be entered.
Freelance operators who do not belong to an origination
should enter “~”.
COUNTRY: Sets the country code.
ORGANIZATION: Sets the organization code.
USER: Sets the user code
See the next item “About the UMID ownership
information” for more information about these codes.
2
3
Set the ownership information using the arrow buttons
and jog dial.
USER (user code)
Arrow buttons: Select the item to set and the
character input location (it blinks).
Jog dial: Selects characters to input at the selected
location.
Enter a 4-byte alphanumeric string to identify the user.
The user code is registered with each organization locally.
It is usually not centrally registered.
When the user code is less than 4 bytes, enter the user code
at the beginning of the 4 bytes and fill the remainder of the
string with the space character (20H).
RESET button: Deletes all input data.
To cancel the ownership information setting
Press the MENU button.
This user code is determined by the organization. The
methods used depend on the organization.
Press the SET button.
Note
The message “NOW SAVING...” appears, and the
ownership information set in step 2 is saved.
User code cannot be entered when no organization code
has been entered.
information about system menu operations.
107
Using UMID Data
Download from Www.Somanuals.com. All Manuals Search And Download.
MPEG-4 Visual Patent
Portfolio License
This product is licensed under the MPEG-4 Visual Patent
Portfolio License for the personal and non-commercial use
of a consumer for (i) encoding video in compliance with
the MPEG-4 Visual Standard (“MPEG-4 Video”) and/or
(ii) decoding MPEG-4 Video that was encoded by a
consumer engaged in a personal and non-commercial
activity and/or was obtained from a video provider
licensed by MPEG LA to provide MPEG-4 Video.
No license is granted or shall be implied for any other use.
Additional information including that relating to
promotional, internal and commercial uses and licensing
may be obtained from MPEG LA, LLC.
See http://www.mpegla.com
108
MPEG-4 Visual Patent Portfolio License
Download from Www.Somanuals.com. All Manuals Search And Download.
be used to record information such as
titles and comments.
UMID
Unique Material Identifier. A
standard (SMPTE 330M) for video
and audio metadata. The Basic
section of a UMID contains a
globally unique number and a
material number for the identification
of recorded material. An optional
section called the “Source Pack”
contains information such as the time
and location of recording. A UMID
with the Basic section only is called a
Basic UMID. A UMID with the
Source Pack is called an Extended
UMID.
Glossary
MXF
Material eXchange Format. A file
exchange format developed by the
Pro-MPEG Forum. Equipment from
different manufacturers can
exchange files in this format.
Clip
A recording unit. Clips are created
every time recording starts and stops.
Clip list
A list of locations in the material
recorded on the disc, arranged in any
order. Clip lists can be created with
the scene selection function of this
unit, and with the supplied PDZ-1
Proxy Browsing Software.
Non-drop-frame mode
A mode of advancing time code
which ignores the difference in frame
values between real time and the time
code. Using this mode produces a
difference of approximately 86
seconds per day between real time
and time code, which causes
problems when editing programs in
units of seconds using the number of
frames as a reference.
User bits
Composite video signal
A video signal in which luminance
and chrominance are combined along
with timing reference “sync”
information to make composite
video.
A total of 32 bits are provided in the
time code which the user can use to
record such information as date, reel
number, or scene number on video
tape or disc. Also called user’s bits.
Proxy AV data
Low-resolution data with a video
bandwidth of 1.5 Mbps and an audio
bandwidth of 64 kbps per channel.
This unit records proxy AV data
automatically whenever high-
resolution MPEG HD or DVCAM
data is recorded.
VBID (Video Blanking ID)
This is a video ID signal, defined in
the EIAJ CPR-1204 standard, which
is inserted into VBS video output to
enable the aspect ratio to be detected.
The ID signal is inserted into line 20,
VBI 283.
Drop-frame mode
SMPTE time code runs at 30 frames/
second, while the NTSC color
television system runs at about 29.97
frames/second. Drop-frame mode
adjusts the running of time code to
eliminate the discrepancy between
time code value and actual time by
dropping two frames from the time
code value at the beginning of each
minute except every tenth minute.
S/N
Signal-to-Noise ratio. The relation of
the strength of the desired signal to
the accompanying electronic
interference, the noise. If S/N is high,
sounds are reproduced with less noise
and pictures are reproduced clearly
without snow.
Essence mark
A type of metadata that may be set for
a specified frame.
For more efficient searches,
XDCAM equipment records essence
marks as part of Non-RealTime
metadata, and uses them to display
thumbnails.
Sub clip
One of the sections which make up a
clip list. A sub clip may be part of a
clip or an entire clip.
i.LINK
Thumbnail image
Another name for the IEEE1394-
1995 standards and their revisions.
XDCAM uses the i.LINK interface to
transfer DV streams by the AV/C
protocol, and to read and write
MPEG HD and DVCAM data files
by FAM (file access mode).
A reduced still picture of video for
display on a GUI screen. XDCAM
creates thumbnail images from proxy
video, and displays them as index
pictures on GUI screens.
Time code
A digitally encoded signal which is
recorded with video data to identify
each frame of the video by hour,
minute, second and frame number.
SMPTE time code is applied to
NTSC system, and EBU time code to
PAL and SECAM systems.
Metadata
Information about the properties of
video and audio content. XDCAM
records metadata such as UMIDs and
essence marks, and the supplied
PDZ-1 Proxy Browsing Software can
Glossary
109
Download from Www.Somanuals.com. All Manuals Search And Download.
connecting an external monitor
F
Index
A
AUDIO OUTPUT 1/3 and 2/4
Audio recording
D
Disc capacity
deleting the most recent recorded
G
B
displaying the status of the current
H
C
I
ejecting with the unit powered off
including a clip selected in the
loading a clip list from a disc into
J
E
modifying the in and out points of
Editing control unit
Editing functions of the recorder
connections using the i.S400
Essence marks
K
L
M
110
Index
Download from Www.Somanuals.com. All Manuals Search And Download.
Shot marks
R
to specify the frame to use as the
thumbnail image 40
when recording does not end
normally 36
Status information (supplementary)
34
N
O
P
T
Thumbnail image
S
Search
searching with the chapter
function 46
searching with the expand
function 44
displaying a list of thumbnail
images 43
OPERATIONAL FUNCTION
79
recording after setting an initial
value 38
recording sequentially upon the
39
returning the factory default
settings 88
Q
U
Index
111
Download from Www.Somanuals.com. All Manuals Search And Download.
User bit values
V
W
Y
Y/PB/PR 24
112
Index
Download from Www.Somanuals.com. All Manuals Search And Download.
Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
|