2-665-741-E2(1)
CD/DVD
Player
Operating Instructions
DVP-NS15
© 2006 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
On adjusting volume
Do not turn up the volume while listening to
a section with very low level inputs or no
audio signals. If you do, the speakers may be
damaged when a peak level section is played.
Precautions
On safety
Should any solid object or liquid fall into the
cabinet, unplug the player and have it
checked by qualified personnel before
operating it any further.
On cleaning
Clean the cabinet, panel, and controls with a
soft cloth slightly moistened with a mild
detergent solution. Do not use any type of
abrasive pad, scouring powder or solvent
such as alcohol or benzine.
On power sources
• The player is not disconnected from the AC
power source (mains) as long as it is
connected to the wall outlet, even if the
player itself has been turned off.
• If you are not going to use the player for a
long time, be sure to disconnect the player
from the wall outlet. To disconnect the AC
power cord (mains lead), grasp the plug
itself; never pull the cord.
On cleaning discs, disc/lens cleaners
Do not use a commercially available
cleaning disc or disc/lens cleaner (wet or
spray type). These may cause the
apparatus to malfunction.
IMPORTANT NOTICE
Caution: This player is capable of holding a
still video image or on-screen display image
on your television screen indefinitely. If
you leave the still video image or on-screen
display image displayed on your TV for an
extended period of time you risk permanent
damage to your television screen. Plasma
display panel televisions and projection
televisions are susceptible to this.
On placement
• Place the player in a location with adequate
ventilation to prevent heat build-up in the
player.
• Do not place the player on a soft surface
such as a rug.
• Do not place the player in a location near
heat sources, or in a place subject to direct
sunlight, excessive dust, or mechanical
shock.
If you have any questions or problems
concerning your player, please consult your
nearest Sony dealer.
On operation
• If the player is brought directly from a cold
to a warm location, or is placed in a very
damp room, moisture may condense on the
lenses inside the player. Should this occur,
the player may not operate properly. In this
case, remove the disc and leave the player
turned on for about half an hour until the
moisture evaporates.
• When you move the player, take out any
discs. If you don’t, the disc may be
damaged.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
About This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Hooking Up the Player. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Step 6: Quick Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
(Multi-disc Resume). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Playing VIDEO CDs With PBC Functions (PBC Playback) . . . . . . . . . . . . . . 23
Various Play Mode Functions (Programme Play, Shuffle Play, Repeat Play,
A-B Repeat Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Searching for a Particular Point on a Disc (Scan, Slow-motion Play,
Freeze Frame) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
TV Virtual Surround Settings (TVS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Adjusting the Playback Picture (CUSTOM PICTURE MODE). . . . . . . . . . . . 38
Sharpening the Picture (SHARPNESS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Locking Discs (CUSTOM PARENTAL CONTROL,
PARENTAL CONTROL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Setting the Display or Sound Track Language (LANGUAGE SETUP) . . . . . 53
Settings for the Display (SCREEN SETUP). . . . . . . . . . . . . . . . . . . . . . . . . . 54
Custom Settings (CUSTOM SETUP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Settings for the Sound (AUDIO SETUP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Self-diagnosis Function (When letters/numbers appear in the display). . . . . 60
Parental Control Area Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
About This Manual
•Instructions in this manual describe the controls on the remote. You can also use the controls on
the player if they have the same or similar names as those on the remote.
•“DVD” may be used as a general term for DVD VIDEOs, DVD+RWs/DVD+Rs (+VR mode)
and DVD-RWs/DVD-Rs (video mode).
•The meaning of the icons used in this manual is described below:
Icons
Meaning
Functions available for DVD VIDEOs and DVD+RWs/DVD+Rs in +VR
mode or DVD-RWs/DVD-Rs in video mode
Functions available for DVD-RWs/DVD-Rs in VR (Video Recording)
mode
Functions available for VIDEO CDs (including Super VCDs or CD-Rs/
CD-RWs in video CD format or Super VCD format)
Functions available for music CDs or CD-Rs/CD-RWs in music CD format
Functions available for DATA CDs (CD-ROMs/CD-Rs/CD-RWs
containing MP3* audio tracks and JPEG image files)
Functions available for DATA DVDs (DVD-ROMs/DVD+RWs/
DVD+Rs/DVD-RWs/DVD-Rs containing MP3* audio tracks and JPEG
image files)
* MP3 (MPEG-1 Audio Layer III) is a standard format defined by ISO (International Organization for
Standardization)/IEC (International Electrotechnical Commission) MPEG which compresses audio data.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Example of discs that the player
cannot play
This Player Can Play the
Following Discs
The player cannot play the following discs:
• CD-ROMs/CD-Rs/CD-RWs other than
those recorded in the formats listed on this
page.
• CD-ROMs recorded in PHOTO CD format.
• Data part of CD-Extras.
Format of discs
DVD VIDEO
• DVD Audio discs.
• HD layer on Super Audio CDs.
DVD-RW/-R
DVD+RW/+R
Also, the player cannot play the following
discs:
• A DVD VIDEO with a different region
code.
• A disc that has a non-standard shape (e.g.,
card, heart).
• A disc with paper or stickers on it.
• A disc that has the adhesive of cellophane
tape or a sticker still left on it.
VIDEO CD/
Music CD
Region code
CD-RW/-R
Your player has a region code printed on the
back of the unit and only will play DVD
VIDEOs (playback only) labelled with
identical region codes. This system is used to
protect copyrights.
“DVD+RW,” “DVD-RW,” “DVD+R,”
“DVD-R,” “DVD VIDEO,” and “CD” logos
are trademarks.
ALL
DVD VIDEOs labelled
this player.
will also play on
Note about CDs/DVDs
The player can play CD-ROMs/CD-Rs/CD-
RWs recorded in the following formats:
– music CD format
If you try to play any other DVD VIDEO, the
message “Playback prohibited by area
limitations.” will appear on the TV screen.
Depending on the DVD VIDEO, there may
be no region code indication, even though
playing the DVD VIDEO is prohibited by
area restrictions.
– video CD format
– MP3 audio tracks and JPEG image files of
format conforming to ISO 9660* Level 1/
Level 2, or its extended format, Joliet
– KODAK Picture CD format
DVP–XXXX
* A logical format of files and folders on CD-
ROMs, defined by ISO (International
Organization for Standardization).
X
Region code
00V 00Hz
NO.
00W
0-000-000-00
The player can play DVD-ROMs/
DVD+RWs/DVD-RWs/DVD+Rs/DVD-Rs
recorded in the following formats:
– MP3 audio tracks and JPEG image files of
format conforming to UDF (Universal Disk
Format).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Copyrights
• Notes about DVD+RWs/DVD+Rs, DVD-RWs/
DVD-Rs or CD-Rs/CD-RWs
This product incorporates copyright
protection technology that is protected by
U.S. patents and other intellectual property
rights. Use of this copyright protection
technology must be authorized by
Macrovision, and is intended for home and
other limited viewing uses only unless
otherwise authorized by Macrovision.
Reverse engineering or disassembly is
prohibited.
Some DVD+RWs/DVD+Rs, DVD-RWs/DVD-
Rs, or CD-Rs/CD-RWs cannot be played on this
player due to the recording quality or physical
condition of the disc, or the characteristics of the
recording device and authoring software.
The disc will not play if it has not been correctly
finalized. For more information, refer to the
operating instructions for the recording device.
Note that some playback functions may not work
with some DVD+RWs/DVD+Rs, even if they
have been correctly finalized. In this case, view
the disc by normal playback. Also some DATA
CDs/DATA DVDs created in Packet Write
format cannot be played.
• Music discs encoded with copyright protection
technologies
This product is designed to playback discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware that
among those discs, there are some that do not
conform to the CD standard and may not be
playable by this product.
• Note on DualDiscs
A DualDisc is a two sided disc product which
mates DVD recorded material on one side with
digital audio material on the other side.
However, since the audio material side does not
conform to the Compact Disc (CD) standard,
playback on this product is not guaranteed.
Note on playback operations of
DVDs and VIDEO CDs
Some playback operations of DVDs and
VIDEO CDs may be intentionally set by
software producers. Since this player plays
DVDs and VIDEO CDs according to the disc
contents the software producers designed,
some playback features may not be available.
Also, refer to the instructions supplied with
the DVDs or VIDEO CDs.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote
J
m/M
(scan/slow) buttons
L SLOW PLAY/FAST PLAY buttons
M
N
(audio) button (34)
(subtitle) button (37)
The + button has a tactile dot.*
R PICTURE NAVI (picture navigation)
The H button has a tactile dot.*
wj
(angle) button (37)
* Use the tactile dot as a reference when operating
the player.
The number 5 button has a tactile dot.*
H
/
(replay/step/
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the Control Menu Display (Magic Pad)
Use the Control Menu to select a function and to view related information. Press DISPLAY
repeatedly to turn on or change the Control Menu display as follows:
, Control Menu display 1
m
Control Menu display 2 (Only for DATA CDs/DATA DVDs)
m
Control Menu display off
Control Menu display
The Control Menu display 1 and 2 will show different items depending on the disc type. For
details about each item, see the pages in parentheses.
Example: Control Menu display 1 when playing a DVD VIDEO.
2
Currently playing chapter number*
1
Currently playing title number*
1
Total number of titles*
Playback status
(N Playback,
X Pause,
2
Total number of chapters*
x Stop, etc.)
Control Menu items
Type of disc
being played*
3
(
)
)
1 2 2 7
DVD VIDEO
(
1 8 3 4
4
Playing time*
Current setting
T
1 : 3 2 : 5 5
Selected item
OFF
OFF
SET
ON
Options
Function name of
selected Control
Menu item
PROGRAM
ENTER
DISPLAY
Quit:
Operation message
*1 Displays the scene number for VIDEO CDs
(PBC is on), track number for VIDEO CDs/CDs,
album number for DATA CDs/DATA DVDs.
*2 Displays the index number for VIDEO CDs,
MP3 audio track number or JPEG image file
number for DATA CDs/DATA DVDs.
*3 Displays Super VCD as “SVCD.”
*4 Displays the date for JPEG files.
To turn off the display
Press DISPLAY.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Control Menu items
Item
Item Name, Function
Selects the title, scene, or track to be played.
CHAPTER (page 29)/INDEX (page 29)
Selects the chapter or index to be played.
Selects the track to be played.
ORIGINAL/PLAY LIST (page 22)
Selects the type of titles (DVD-RW/DVD-R in VR mode) to be played, the ORIGINAL
one, or an edited PLAY LIST.
TIME/TEXT (page 29)
Checks the elapsed time and the remaining playback time.
Input the time code for picture and music searching.
Displays the DVD/CD text, or the DATA CD/DATA DVD track/file name.
Selects the title, chapter, or track to play in the order you want.
SHUFFLE (page 25)
Plays the title, chapter, or track in random order.
REPEAT (page 26)
Plays the entire disc (all titles/all tracks/all albums) repeatedly or one title/chapter/
track/album repeatedly.
Specifies the parts you want to play repeatedly.
CUSTOM PICTURE MODE (page 38)
Adjusts the video signal from the player. You can select the picture quality that best
suits the program you are watching.
Exaggerates the outline of the image to produce a sharper picture.
Set to prohibit playback on this player.
Use Quick Setup to choose the desired language of the on-screen display, the aspect
ratio of the TV, and the audio output signal.
CUSTOM Setup
In addition to the Quick Setup setting, you can adjust various other settings.
RESET
Returns the settings in “SETUP” to the default setting.
ALBUM (page 29)
Selects the album that contains the MP3 audio tracks and JPEG image files to be
played.
Selects the JPEG image file to be played.
Displays the date the picture was taken by a digital camera.
Specifies the duration for which the slides are displayed on the screen.
,continued
11
Download from Www.Somanuals.com. All Manuals Search And Download.
EFFECT (page 47)
Selects the effects to be used for changing slides during a slide show.
Selects the data type; MP3 audio track (AUDIO), JPEG image file (IMAGE) or both
(AUTO) to be played when playing a DATA CD/DATA DVD.
z Hint
The Control Menu icon indicator lights up in green
when you select any item
t
except “OFF.” (“PROGRAM,” “SHUFFLE,”
“REPEAT,” “A-B REPEAT,” “SHARPNESS,”
“CUSTOM PICTURE MODE” only). The
“ORIGINAL/PLAY LIST” indicator lights up in
green when you select “PLAY LIST” (default
setting).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Hookups
Hooking Up the Player
Follow steps 1 to 6 to hook up and adjust the settings of the player.
Notes
• Plug cords securely to prevent unwanted noise.
• Refer to the instructions supplied with the components to be connected.
• You cannot connect this player to a TV that does not have a SCART input jack.
• Be sure to disconnect the mains lead of each component before connecting.
Step 1: Unpacking
Check that you have the following items:
• Remote commander (remote) (1)
• R6 (size AA) batteries (2)
Step 2: Inserting Batteries Into the Remote
You can control the player using the supplied remote. Insert two R6 (size AA) batteries by
matching the 3 and # ends on the batteries to the markings inside the compartment. When
using the remote, point it at the remote sensor
on the player.
Notes
• Do not leave the remote in an extremely hot or humid place.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light from the sun or a lighting apparatus. Doing so may cause a
malfunction.
• If you do not use the remote for an extended period of time, remove the batteries to avoid possible damage
from battery leakage and corrosion.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3: Connecting to your TV
Connect this player to your TV monitor, or projector using an audio/video (SCART) cord. This
connection will use your TV speakers for sound.
INPUT
TV
SCART cord
(not supplied)
to LINE (RGB)-TV
COAXIAL
DIGITAL OUT
CD/DVD player
l : Signal flow
When connecting to a SCART input jack
Connect a SCART cord (not supplied). Be sure to make the connections firmly to avoid hum and
noise.
TV: Dynamic Theatre, Dynamic, Wide, Night
When using this connection, check that the TV conforms to S video or RGB signals. Refer to the
operating instructions supplied with the TV to be connected. Also, when you set “LINE” to
cord that conforms to each signal.
When connecting to a standard 4:3 screen TV
Depending on the disc, the image may not fit your TV screen. To change the aspect ratio, see
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
• Do not connect a VCR, etc., between your TV and the player. If you pass the player signals via the VCR,
you may not receive a clear image on the TV screen.
VCR
CD/DVD player
TV
Connect
directly
• When you connect the player to your TV via the SCART jacks, the TV’s input source is set to the player
automatically when you start playback. In this case, press t (TV/video) on the remote to return the input
to the TV.
When you play a disc recorded in the NTSC colour system, the player outputs the video signal
or the Setup Display etc. in the NTSC colour system and the picture may not appear on the
PAL colour system televisions. In this case, open the tray and remove the disc.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4: Connecting to an AV amplifier (receiver)
1
2
If your AV amplifier (receiver) has a Dolby Digital* , DTS* or MPEG audio decoder and a
digital input jack, use this connection.
COAXIAL
DIGITAL OUT
CD/DVD player
to DIGITAL OUT (COAXIAL)
COAXIAL
DIGITAL OUT
Coaxial digital cord
(not supplied)
to coaxial
digital input
[Speakers]
Rear (R)
[Speakers]
Rear (L)
Front (L)
Front (R)
AV amplifier (receiver)
with a decoder
Center
Subwoofer
: Signal flow
z Hint
For correct speaker location, see the operating instructions supplied with the connected components.
• Surround effect
Dolby Digital (5.1ch), DTS (5.1ch), MPEG audio (5.1ch)
*1 Manufactured under license from Dolby Laboratories. “Dolby,” “Pro Logic,” and the double-D symbol
are trademarks of Dolby Laboratories.
*2 “DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
Notes
• After you have completed the connection, make the appropriate settings in Quick Setup (page 17). If your
AV amplifier (receiver) has an MPEG audio decoder function, set “MPEG” to “MPEG” in Audio Setup
(page 57). Otherwise, no sound or a loud noise will come from your speakers.
• The TVS effects of this player cannot be used with this connection.
• In order to listen to DTS sound tracks, you must use this connection. DTS sound tracks are not output
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 5: Connecting the Mains Lead
Plug the player and TV mains lead (power cord) into a mains.
Step 6: Quick Setup
Follow the steps below to make the minimum number of basic adjustments for using the player.
To skip an adjustment, press >. To return to the previous adjustment, press ..
ENTER
1
2
Turn on the TV.
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
ENGLISH
Press [/1.
ENGLISH
FRANÇAIS
DEUTSCH
ITALIANO
The player turns on and the power
indicator lights up.
ESPAÑOL
NEDERLANDS
DANSK
3
Switch the input selector on your
TV so that the signal from the
player appears on the TV screen.
SVENSKA
5
6
Press X/x to select a language.
The player displays the menu and
subtitles in the selected language.
“Press [ENTER] to run QUICK SETUP”
(press enter to run Quick Setup) appears
at the bottom of the screen. If this
message does not appear, select
“QUICK” (quick) under “SETUP”
(setup) in the Control Menu to run Quick
Press ENTER.
The Setup Display for selecting the
aspect ratio of the TV to be connected
appears.
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
LINE:
4
Press ENTER without inserting a
disc.
16:9
16:9
4:3 LETTER BOX
4:3 PAN SCAN
The Setup Display for selecting the
language used in the on-screen display
appears.
,continued
17
Download from Www.Somanuals.com. All Manuals Search And Download.
If you did not connect an AV amplifier
(receiver), select “NO,” then go to step
15.
If you connected an AV amplifier
(receiver) using a coaxial digital cord,
select “YES: DIGITAL OUTPUT.”
7
8
PressX/xto select the setting that
matches your TV type.
◆ If you have a wide-screen TV or a 4:3
standard TV with a wide-screen mode
◆ If you have a 4:3 standard TV
• 4:3 LETTER BOX or 4:3 PAN SCAN
12Press X/x to select the type of
Dolby Digital signal you wish to
send to your amplifier (receiver).
Press ENTER.
If your AV amplifier (receiver) has a
Dolby Digital decoder, select “DOLBY
DIGITAL.” Otherwise, select “D-PCM.”
The Setup Display for selecting the type
of video signal output from the LINE
(RGB)-TV jack appears.
AUDIO SETUP
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
LINE:
AUDIO DRC:
DOWNMIX:
DIGITAL OUT:
DOLBY DIGITAL:
MPEG:
DTS:
48kHz/96kHz PCM:
STANDARD
DOLBY SURROUND
ON
16:9
ON
JACKET PICTURE
VIDEO
D-PCM
D-PCM
DOLBY DIGITAL
48kHz/16bit
VIDEO
S VIDEO
RGB
13Press ENTER.
9
Press X/x to select the type of
signal you want to output from the
LINE (RGB)-TV jack.
“DTS” is selected.
AUDIO SETUP
AUDIO DRC:
DOWNMIX:
DIGITAL OUT:
DOLBY DIGITAL:
MPEG:
STANDARD
DOLBY SURROUND
◆ Video signals
• VIDEO (page 54)
ON
D-PCM
PCM
OFF
◆ S video signals
• S VIDEO (page 54)
DTS:
48kHz/96kHz PCM:
OFF
ON
◆ RGB signals
• RGB (page 54)
14Press X/x to select whether or
not you wish to send a DTS signal
to your amplifier (receiver).
10Press ENTER.
The Setup Display for selecting the type
of jack used to connect your amplifier
(receiver) appears.
If your AV amplifier (receiver) has a
DTS decoder, select “ON.” Otherwise,
select “OFF.”
Is this player connected to an amplifier
(receiver) ?
YES
15Press ENTER.
DIGITAL OUTPUT
Quick Setup is finished. All connections
and setup operations are complete.
If your AV amplifier (receiver) has an
MPEG audio decoder, set “MPEG” to
“MPEG” (page 57).
NO
11Press X/x to select the type of
jack (if any) you are using to
connect to an amplifier (receiver),
then press ENTER.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
Press Aon the player, and place a
disc on the disc tray.
Playing Discs
Playing Discs
Depending on the DVD or VIDEO CD, some
operations may be different or restricted.
Refer to the operating instructions supplied
with your disc.
Playback side facing down
Press H.
The disc tray closes. The player starts
playback (continuous play) and the play
indicator lights up. Adjust the volume on
the TV or the amplifier (receiver).
Depending on the disc, a menu may
appear on the TV screen. For DVD
To turn off the player
Press [/1. The player enters standby mode.
ENTER
RETURN
z Hint
You can have the player turn off automatically
whenever you leave it in stop mode for more than
30 minutes. To turn this function on or off, set
“AUTO POWER OFF” in “CUSTOM SETUP” to
Notes
• The play indicator lights up each time the disc is
in playback mode.
1
2
Turn on your TV.
• Discs created on DVD recorders must be correctly
finalized before they can be played. For more
information about finalizing, refer to the
operating instructions supplied with the DVD
recorder.
Press [/1.
The player turns on and the power
indicator lights up.
3
Switch the input selector on your
TV so that the signal from the
player appears on the TV screen.
Notes on playing DTS sound tracks on a
DVD VIDEO
• DTS audio signals are output only through the
DIGITAL OUT (COAXIAL) jack.
• When you play a DVD VIDEO with DTS sound
tracks, set “DTS” to “ON” in “AUDIO SETUP”
• If you connect the player to audio equipment
without a DTS decoder, do not set “DTS” to “ON”
come out from the speakers, affecting your ears or
causing the speakers to be damaged.
◆ When using an amplifier (receiver)
Turn on the amplifier (receiver) and
select the appropriate channel so that you
can hear sound from the player.
,continued
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Additional operations
You may not be able to use the Replay or Advance
function with some scenes.
Playback quickly or slowly with
sound
CLEAR
(replay)
You can listen to dialogue or sound while
playing the current scene quickly or slowly.
During playback, press FAST PLAY or
SLOW PLAY.
(advance)
The speed changes when you press either
FAST PLAY or SLOW PLAY.
ZOOM
To return to normal playback
Press H.
SLOW PLAY
FAST PLAY
To
Operation
Notes
• You can only use this function with DVDs/
VIDEO CDs/Super VCDs and DVD-RWs/
DVD-Rs in VR mode only.
Stop
Pause
Press x
Press X
• “Operation not possible” will appear when
maximum or minimum speed is reached.
• During FAST PLAY and SLOW PLAY mode,
be changed for VIDEO CDs/Super VCDs.
• Fast Play and Slow Play functions do not work
when playing DTS sound tracks.
Resume play after
pause
Press X or H
Go to the next chapter, Press >
track, or scene in
continuous play mode
Go back to the
Press .
previous chapter,
track, or scene in
continuous play mode
• You cannot use Fast Play and Slow Play functions
when playing a still picture on DVD-RW/DVD-R
in VR mode.
Stop play and remove Press Z
the disc
Locking the disc tray (Child Lock)
You can lock the disc tray to prevent children
from opening it.
Replay the previous
scene*1
Press
(replay) during
playback
When the player is in standby mode, press
O RETURN, ENTER, and then [/1 on the
remote.
The player turns on. The A and Z buttons on
the player or the remote do not work while the
Child Lock is set.
Briefly fast forward
the current scene*2
Press
(advance) during
playback
Magnify the image*3 Press ZOOM
repeatedly. Press
CLEAR to cancel.
1
*
*
DVD VIDEOs/DVD-RWs/DVD-Rs only.
DVD VIDEOs/DVD-RWs/DVD-Rs/
DVD+RWs/DVD+Rs only.
Video and JPEG pictures only (except
BACKGROUND pictures). You can move the
enlarged picture using C/X/x/c. Depending
upon the contents of the disc, the zoom function
may be cancelled automatically when the
picture is moved.
2
To unlock the disc tray
When the player is in standby mode, press
O RETURN, ENTER, and then [/1 again.
3
*
Note
Even if you select “RESET” under “SETUP” in the
locked.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
ResumingPlaybackFrom
the Point Where You
Stopped the Disc (Multi-disc
Resume)
• “MULTI-DISC RESUME” in “CUSTOM
SETUP” must be set to “ON” (default) for this
• The point where you stopped playing is cleared
when:
– you change the play mode.
– you change the settings on the Setup Display.
• For DVD-RWs/DVD-Rs in VR mode, CDs,
DATA CDs, and DATA DVDs, the player
remembers the resume playback point for the
current disc.
The resume point is cleared when:
– you opened the disc tray.
– you disconnect the mains lead.
The player stores the point where you stopped
the disc for up to 6 discs and resumes
playback the next time you insert the same
disc. If you store a resume playback point for
the seventh disc, the resume playback point
for the first disc is deleted.
– the player enters standby mode.
• Resume Play does not work during Shuffle Play
and Programme Play.
• This function may not work with some discs.
• If “MULTI-DISC RESUME” in “CUSTOM
SETUP” is set to “ON” and you playback a
recorded disc such as DVD-RW, the player may
playback other recorded discs from the same
resume point.
1
2
While playing a disc, press x to
stop playback.
Press H.
The player starts playback from the point
where you stopped the disc in step 1.
z Hint
To play from the beginning of the disc, press x
twice, then press H.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the DVD’s Menu
Selecting “ ORIGINAL” or
“ PLAY LIST” on a DVD-
RW/DVD-R
Some DVD-RWs/DVD-Rs in VR (Video
Recording) mode have two types of titles for
playback: originally recorded titles
(ORIGINAL) and titles that can be created on
recordable DVD players for editing (PLAY
LIST). You can select the type of title to be
played.
A DVD is divided into long sections of a
picture or a music feature called “titles.”
When you play a DVD which contains
several titles, you can select the title you want
using the TOP MENU button.
When you play DVDs that allow you to select
items such as language for the sound and
subtitles, select these items using the MENU
button.
Number
buttons
TOP MENU
MENU
ENTER
ENTER
DISPLAY
1
2
Press DISPLAY when the player is
in stop mode.
The Control Menu appears.
1
2
Press TOP MENU or MENU.
Press X/x to select
(ORIGINAL/PLAYLIST), thenpress
ENTER.
The disc’s menu appears on the TV
screen.
The contents of the menu vary from disc
to disc.
The options for “ORIGINAL/PLAY
LIST” appear.
Press C/X/x/c or the number
buttons to select the item you want
to play or change.
(
)
)
1 2 2 7
(
1 8 3 4
DVD-VR
T
1 : 3 2 : 5 5
PLAY LIST
PLAY LIST
ORIGINAL
If you press the number buttons, the
following display appears.
Press the number buttons to select the
item you want.
1
3
4
Press X/x to select a setting.
• PLAY LIST: plays the titles created
from “ORIGINAL” for editing.
• ORIGINAL: plays the titles originally
recorded.
3
Press ENTER.
Press ENTER.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
z Hint
To play without using PBC, press ./> or the
number buttons while the player is stopped to select
a track, then press H or ENTER.
“Play without PBC” appears on the TV screen and
the player starts continuous play. You cannot play
still pictures such as a menu.
Playing VIDEO CDs With
PBCFunctions(PBCPlayback)
To return to PBC playback, press x twice then
press H.
PBC (Playback Control) allows you to play
VIDEO CDs interactively by following the
menu on the TV screen.
Note
Depending on the VIDEO CD, “Press ENTER” in
step 3 may appear as “Press SELECT” in the
instructions supplied with the disc. In this case,
press H.
Number
buttons
ENTER
RETURN
1
2
Start playing a VIDEO CD with PBC
functions.
The menu for your selection appears.
Press the number buttons to select
the item number you want.
3
4
Press ENTER.
Follow the instructions in the
menu for interactive operations.
Refer to the instructions supplied with the
disc, as the operating procedure may
differ depending on the VIDEO CD.
To return to the menu
Press O RETURN.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
(
)
)
1 2 2 7
DVD VIDEO
(
1 8 3 4
Various Play Mode
Functions (Programme Play,
Shuffle Play, Repeat Play, A-B Repeat
Play)
T
1 : 3 2 : 5 5
OFF
OFF
SET
ON
You can set the following play modes:
• Programme Play (page 24)
• Shuffle Play (page 25)
3 Press X/x to select “ SET t,” then
press ENTER.
• A-B Repeat Play (page 27)
“TRACK” is displayed when you play
a VIDEO CD or CD.
PROGRAM
T
ALL CLEAR
– –
1. TITLE
2. TITLE
3. TITLE
4. TITLE
5. TITLE
6. TITLE
7. TITLE
– –
– –
– –
– –
– –
– –
01
02
03
04
05
CLEAR
ENTER
Titles or tracks
recorded on a disc
DISPLAY
4 Press c.
The cursor moves to the title or track row
“T” (in this case, “01”).
PROGRAM
T
C
ALL CLEAR
1. TITLE
– –
– –
01
02
03
04
05
ALL
– –
– –
– –
– –
– –
– –
Note
2. TITLE
3. TITLE
4. TITLE
5. TITLE
6. TITLE
7. TITLE
01
02
03
04
05
06
The play mode is cancelled when:
– you eject the disc.
– the player enters standby mode by pressing [/1.
Creating your own programme
(Programme Play)
Chapters recorded on a disc
5 Select the title, chapter, or track you
want to programme.
You can play the contents of a disc in the
order you want by arranging the order of the
titles, chapters, or tracks on the disc to create
your own programme. You can programme
up to 99 titles, chapters, and tracks.
◆ When playing a DVD VIDEO
For example, select chapter “03” of title
“02.”
Press X/x to select “02” under “T,” then
press ENTER.
1 Press DISPLAY.
The Control Menu appears.
PROGRAM
2 Press X/x to select
T
C
ALL CLEAR
(PROGRAM), then press ENTER.
The options for “PROGRAM” appear.
– –
– –
ALL
1. TITLE
2. TITLE
3. TITLE
4. TITLE
5. TITLE
6. TITLE
7. TITLE
– –
– –
– –
– –
– –
– –
01
02
03
04
05
06
01
02
03
04
05
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Next, press X/x to select “03” under “C,”
3
Follow step 5 for new programming. To
cancel a programme, select “--” under
“T,” then press ENTER.
then press ENTER.
PROGRAM
T
ALL CLEAR
1. TITLE 0 2 0 3
To cancel all of the titles, chapters, or
tracks in the programmed order
–
– –
– –
– –
– –
– –
– –
– –
2. TITLE
3. TITLE
4. TITLE
5. TITLE
6. TITLE
7. TITLE
01
02
03
04
05
1
Follow steps 1 to 3 of “Creating your own
2
3
Press X and select “ALL CLEAR.”
Press ENTER.
Selected title and chapter
z Hint
◆ When playing a VIDEO CD or CD
For example, select track “02.”
Press X/x to select “02” under “T,” then
press ENTER.
You can perform Repeat Play or Shuffle Play of
programmed titles, chapters, or tracks. During
Programme Play, follow the steps of Repeat Play
Selected track
Notes
0:15:30
T
PROGRAM
• When you programme tracks on a Super VCD, the
total playing time is not displayed.
• You cannot use this function with VIDEO CDs or
Super VCDs with PBC playback.
ALL CLEAR
1. TRACK
2. TRACK
3. TRACK
4. TRACK
5. TRACK
6. TRACK
7. TRACK
– –
0 2
– –
– –
– –
– –
– –
– –
01
02
03
04
05
Playing in random order (Shuffle
Play)
Total time of the programmed tracks
You can have the player “shuffle” titles,
chapters, or tracks. Subsequent “shuffling”
may produce a different playing order.
6 To programme other titles, chapters,
or tracks, repeat steps 4 to 5.
The programmed titles, chapters, and
tracks are displayed in the selected order.
1 Press DISPLAY during playback.
The Control Menu appears.
7 Press H to start Programme Play.
2 Press X/x to select
Programme Play begins.
(SHUFFLE), then press ENTER.
The options for “SHUFFLE” appear.
When the programme ends, you can
restart the same programme again by
pressing H.
(
)
)
1 2 2 7
DVD VIDEO
(
1 8 3 4
T
1 : 3 2 : 5 5
OFF
OFF
To return to normal play
TITLE
CHAPTER
Press CLEAR, or select “OFF” after step 2.
To play the same programme again, select
“ON” in step 3 and press ENTER.
To change or cancel a programme
3 Press X/x to select the item to be
1
Follow steps 1 to 3 of “Creating your
shuffled.
◆ When playing a DVD VIDEO
• TITLE
• CHAPTER
2
Select the programme number of the title,
chapter, or track you want to change or
cancel using X/x and press c. If you
want to delete the title, chapter, or track
from the programme, press CLEAR.
◆ When playing a VIDEO CD or CD
• TRACK
,continued
25
Download from Www.Somanuals.com. All Manuals Search And Download.
◆ When Programme Play is activated
• ON: shuffles titles, chapters, or tracks
selected in Programme Play.
◆ When playing a DVD-VR mode disc
• DISC: repeats all the titles of the
selected type.
• TITLE: repeats the current title on a
disc.
• CHAPTER: repeats the current chapter.
4 Press ENTER.
Shuffle Play starts.
◆ When playing a VIDEO CD or CD
• DISC: repeats all of the tracks.
• TRACK: repeats the current track.
To return to normal play
Press CLEAR, or select “OFF” in step 3.
◆ When playing a DATA CD/DATA DVD
• DISC: repeats all of the albums.
• ALBUM: repeats the current album.
• TRACK (MP3 audio tracks only):
repeats the current track.
z Hints
• You can set Shuffle Play while the player is
stopped. After selecting the “SHUFFLE” option,
press H. Shuffle Play starts.
• Up to 200 chapters in a disc can be played in
random order when “CHAPTER” is selected.
◆ When Programme Play or Shuffle Play
is activated
• ON: repeats Programme Play or Shuffle
Play.
Note
You cannot use this function with VIDEO CDs or
Super VCDs with PBC playback.
4 Press ENTER.
Repeat Play starts.
Playing repeatedly (Repeat Play)
To return to normal play
Press CLEAR, or select “OFF” in step 3.
You can play all of the titles or tracks on a
disc, or a single title, chapter, or track
repeatedly.
You can use a combination of Shuffle or
Programme Play modes.
z Hint
You can set Repeat Play while the player is stopped.
After selecting the “REPEAT” option, press H.
Repeat Play starts.
1 Press DISPLAY during playback.
The Control Menu appears.
Notes
• You cannot use this function with VIDEO CDs or
Super VCDs with PBC playback.
• When repeating a DATA CD/DATA DVD which
contains MP3 audio tracks and JPEG image files,
and their playing times are not the same, the sound
will not match the image.
2 Press X/x to select
(REPEAT), then press ENTER.
The options for “REPEAT” appear.
(
)
)
1 2 2 7
DVD VIDEO
(
1 8 3 4
• When “MODE (MP3, JPEG)” is set to “IMAGE
T
1 : 3 2 : 5 5
OFF
OFF
DISC
TITLE
CHAPTER
3 Press X/x to select the item to be
repeated.
◆ When playing a DVD VIDEO
• DISC: repeats all of the titles.
• TITLE: repeats the current title on a
disc.
• CHAPTER: repeats the current chapter.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Repeating a specific portion
(A-B Repeat Play)
• When you set A-B Repeat Play, the settings for
Shuffle Play, Repeat Play, and Programme Play
are cancelled.
• A-B Repeat Play does not work across multiple
titles.
• You may not set A-B Repeat Play for contents on
a DVD-RW/DVD-R (VR mode) that contains still
pictures.
You can play a specific portion of a title,
chapter or track repeatedly. (This function is
useful when you want to memorize lyrics,
etc.)
1 Press DISPLAY during playback.
The Control Menu appears.
2 Press X/x to select
(A-B
REPEAT), then press ENTER.
The options for “A-B REPEAT” appear.
(
)
)
1 2 2 7
DVD VIDEO
(
1 8 3 4
T
1 : 3 2 : 5 5
OFF
SET
OFF
3 Press X/x to select “ SET t,” then
press ENTER.
The “A-B REPEAT” setting bar appears.
A 18 - 1:32:30
B
4 During playback, when you find the
starting point (point A) of the portion to
be played repeatedly, press ENTER.
The starting point (point A) is set.
A 18 - 1:32:30 B 18 - 1:33:05
5 When you reach the ending point
(point B), press ENTER again.
The set points are displayed and the
player starts repeating this specific
portion.
To return to normal play
Press CLEAR, or select “OFF” in step 3.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Locating a point quickly by
playing a disc in fast forward or
fast reverse (Scan)
Searching for a Scene
Searching for a
Particular Point on a
Disc (Scan, Slow-motion Play,
Freeze Frame)
Press
m or M
while playing a
disc. When you find the point you want, press
H to return to normal speed. Each time you
press
m or M
during scan, the
scan speed changes. With each press the
indication changes as shown below. Actual
speeds may differ between discs.
You can quickly locate a particular point on a
disc by monitoring the picture or playing back
slowly.
Playback direction
×2B t 1M t 2M t 3M
3M (DVD VIDEO/DVD-VR mode/VIDEO CD
only)
×2B (DVD VIDEO/CD only)
Opposite direction
×2b t 1m t 2m t 3m
(step)
(step)
3m (DVD VIDEO/DVD-VR mode/VIDEO CD
only)
×2b (DVD VIDEO only)
The “×2B”/ “×2b” playback speed is about
twice the normal speed.
The “3M”/“3m” playback speed is faster
than “2M”/“2m” and the “2M”/“2m”
playback speed is faster than “1M”/
“1m.”
Notes
• Depending on the disc, you may not be able to do
some of the operations described.
• For DATA CDs/DATA DVDs, you can search for
a particular point only on MP3 audio track.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Watching frame by frame
(Slow-motion Play)
Searching for a Title/
Chapter/Track/Scene,
etc.
Press
m or M
when the player is
in pause mode. To return to normal speed,
press H.
Each time you press
m or M
You can search a DVD by title or chapter, and
you can search a VIDEO CD/CD/DATA CD/
DATA DVD by track, index, file, or scene.
As titles and tracks are assigned unique
numbers on the disc, you can select the
desired one by entering its number. You can
also search for a scene using the time code.
during Slow-motion Play, the playback speed
changes. Two speeds are available. With each
press the indication changes as follows:
Playback direction
2
y 1
Opposite direction (DVD/DVD-VR mode
only)
Number
buttons
2
y 1
The “2 y”/“2
than “1 y”/“1
” playback speed is slower
.”
CLEAR
ENTER
Playing one frame at a time
(Freeze Frame)
DISPLAY
When the player is in the pause mode, press
(step) to go to the next frame. Press
(step) to go to the preceding frame
(DVD/DVD-VR mode only). To return to
normal playback, press H.
1
2
Press DISPLAY (When playing a
DATA CD/DATA DVDs with JPEG
image files, press twice).
Note
You cannot search for a still picture on a DVD-RW/
DVD-R in VR mode.
The Control Menu appears.
Press X/x to select the search
method.
◆ When playing a DVD VIDEO/DVD-VR
mode disc
TITLE
CHAPTER
TIME/TEXT
Select “TIME/TEXT” to search for a
starting point by inputting the time code.
◆ When playing a VIDEO CD or Super
VCD without PBC playback
TRACK
INDEX
,continued
29
Download from Www.Somanuals.com. All Manuals Search And Download.
◆ When playing a VIDEO CD or Super
VCD with PBC Playback
5
Press ENTER.
The player starts playback from the
selected number.
SCENE
◆ When playing a CD
TRACK
To search for a scene using the time code
(DVD VIDEO/DVD-VR mode only)
◆ When playing a DATA CD/DATA DVD
ALBUM
1
In step 2, select
TIME/TEXT.
TRACK (MP3 audio tracks
only)
“T ” (playing time of the current
:
:
** ** **
title) is selected.
FILE (JPEG image files only)
2
3
Press ENTER.
Example: when you select
CHAPTER
“T
:
:
” changes to “T --:--:--.”
** ** **
Input the time code using the number
buttons, then press ENTER.
For example, to find the scene at 2 hours,
10 minutes, and 20 seconds after the
beginning, just enter “2:10:20.”
“
(
)” is selected ( refers to a
** **
**
number).
The number in parentheses indicates the
total number of titles, chapters, tracks,
indexes, scenes, albums or files.
z Hints
(
)
)
DVD VIDEO
1 2 2 7
• When the Control Menu display is turned off, you
can search for a chapter (DVD VIDEO/DVD-VR
mode) or track (CD/DATA CD/DATA DVD) by
pressing the number buttons and ENTER.
• You can display the first scene of titles, chapters,
or tracks recorded on the disc on a screen divided
into 9 sections. You can start playback directly by
selecting one of the scenes. For details, see
(
1 8 3 4
T
1 : 3 2 : 5 5
Selected row
3
4
Press ENTER.
“
(
)” changes to “-- ( ).”
**
** **
Notes
• The title, chapter, or track number displayed is the
same number recorded on the disc.
• You cannot search for a scene on a DVD+RW/
DVD+R using the time code.
(
(
)
)
1 2 2 7
DVD VIDEO
3 4
T
1 : 3 2 : 5 5
Press the number buttons to select
the title, chapter, track, index, or
scene, etc. number you want to
search.
◆ If you make a mistake
Cancel the number by pressing CLEAR,
then select another number.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Searching by Scene
(PICTURE NAVIGATION)
1
4
7
2
5
8
3
6
9
You can divide the screen into 9 subscreens
and find the desired scene quickly.
4
PressC/X/x/ctoselectachapter,
title, or track, and press ENTER.
Playback starts from the selected scene.
PICTURE
NAVI
ENTER
To return to normal play during setting
Press O RETURN or DISPLAY.
DISPLAY
RETURN
z Hint
If there are more than 9 chapters, titles, or tracks, V
is displayed at the bottom right of the screen.
To display the additional chapters, titles, or tracks,
select the bottom scenes and press x. To return to
the previous scene, select the top scenes and press
X.
1
2
Press PICTURE NAVI during
playback.
The following display appears.
Note
Depending on the disc, you may not be able to select
some items.
ENTER
CHAPTER VIEWER
Press PICTURE NAVI repeatedly to
select an item.
• CHAPTER VIEWER (DVD VIDEO
only): displays the first scene of each
chapter.
• TITLE VIEWER (DVD VIDEO only):
displays the first scene of each title.
• TRACK VIEWER (VIDEO CD/
Super VCD only): displays the first
scene of each track.
3
Press ENTER.
The first scene of each chapter, title, or
track appears as follows.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
◆ WhenplayingaDVDVIDEOorDVD-VR
mode disc
Viewing Information About the
Disc
• T : : (hours: minutes: seconds)
* * *
Playing time of the current title
• T– : :
* * *
Checking the Playing
Time and Remaining
Time
Remaining time of the current title
• C : :
* * *
Playing time of the current chapter
• C– : :
* * *
Remaining time of the current chapter
◆ When playing a VIDEO CD or Super
VCD (with PBC functions)
•
:
(minutes: seconds)
You can check the playing time and
remaining time of the current title, chapter, or
track. Also, you can check the DVD/CD text
or track name (MP3 audio) recorded on the
disc.
* *
Playing time of the current scene
◆ When playing a VIDEO CD (without
PBC functions) or CD
• T
:
(minutes: seconds)
* *
Playing time of the current track
• T– :
* *
Remaining time of the current track
• D
:
* *
Playing time of the current disc
• D– :
* *
TIME/TEXT
Remaining time of the current disc
◆ When playing a Super VCD (without
PBC functions)
• T
:
(minutes: seconds)
* *
Playing time of the current track
◆ When playing a DATA CD (MP3 audio)/
DATA DVD (MP3 audio)
• T
:
(minutes: seconds)
* *
Playing time of the current track
1
2
Press TIME/TEXT during playback.
The following display appears.
T
1:01:57
Time
information
Press TIME/TEXT repeatedly to
change the time information.
The available time information depends
upon the type of disc you are playing.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the play information of
the disc
To check the DVD/CD text
Press TIME/TEXT repeatedly in step 2 to
display text recorded on the DVD/CD.
The DVD/CD text appears only when text is
recorded in the disc. You cannot change the
text. If the disc does not contain text, “NO
TEXT” appears.
BRAHMS SYMPHONY
To check DATA CD/DATA DVD album
name, etc.
By pressing TIME/TEXT while playing MP3
audio tracks on a DATA CD/DATA DVD,
you can display the name of the album/track
and the audio bit rate (the amount of data per
second of the current audio track) on your TV
screen.
Bit rate
T
17:30 128k
JAZZ
RIVER SIDE
Album name
Track name
33
Download from Www.Somanuals.com. All Manuals Search And Download.
◆ When playing a DVD VIDEO
Depending on the DVD VIDEO, the
choice of language varies.
Sound Adjustments
When 4 digits are displayed, they
indicate a language code. See “Language
language the code represents. When the
same language is displayed two or more
times, the DVD VIDEO is recorded in
multiple audio formats.
Changing the Sound
◆ When playing a DVD-VR mode disc
The types of sound tracks recorded on a
disc are displayed. The default setting is
underlined.
Example:
• 1: MAIN (main sound)
When playing a DVD VIDEO recorded in
multiple audio formats (PCM, Dolby Digital,
MPEG audio, or DTS), you can change the
audio format. If the DVD VIDEO is recorded
with multilingual tracks, you can also change
the language.
With CDs, DATA CDs, DATA DVDs or
VIDEO CDs, you can select the sound from
either the right or left channel and listen to the
sound of the selected channel through both
the right and left speakers. For example, when
playing a disc containing a song with the
vocals on the right channel and the
instruments on the left channel, you can hear
the instruments from both speakers by
selecting the left channel.
• 1: SUB (sub sound)
• 1: MAIN+SUB (main and sub sound)
◆ When playing a VIDEO CD, CD, DATA
CD (MP3 audio) or DATA DVD (MP3
audio)
The default setting is underlined.
• STEREO: the standard stereo sound
• 1/L: the sound of the left channel
(monaural)
• 2/R: the sound of the right channel
(monaural)
◆ When playing a Super VCD
The default setting is underlined.
• 1:STEREO: the stereo sound of the
audio track 1
• 1:1/L: the sound of the left channel of
the audio track 1 (monaural)
• 1:2/R: the sound of the right channel of
the audio track 1 (monaural)
• 2:STEREO: the stereo sound of the
audio track 2
• 2:1/L: the sound of the left channel of
the audio track 2 (monaural)
• 2:2/R: the sound of the right channel of
the audio track 2 (monaural)
1
2
Press
(audio) during playback.
The following display appears.
:
1
ENGLISH DOLBY DIGITAL 3/2.1
Notes
• While playing a Super VCD on which the audio
track 2 is not recorded, no sound will come out
when you select “2:STEREO,” “2:1/L,” or “2:2/
R.”
• When playing DVD-RW/DVD-R in VR mode: If
you connect to an AV amplifier (receiver) using
the DIGITAL OUT (COAXIAL) jack and want to
switch between the sound tracks, set “DOLBY
DIGITAL” to “D-PCM” in “AUDIO SETUP.”
Press
(audio) repeatedly to
select the desired audio signal.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the audio signal
format
TV Virtual Surround
Settings (TVS)
You can check the audio signal format by
pressing
(audio) repeatedly during
When you connect a stereo TV or 2 front
speakers, TVS (TV Virtual Surround) lets
you enjoy surround sound effects by using
sound imaging to create virtual rear speakers
from the sound of the front speakers (L: left,
R: right) without using actual rear speakers.
TVS was developed by Sony to produce
surround sound for home use using just a
stereo TV.
playback. The format of the current audio
signal (Dolby Digital, DTS, PCM, etc.)
appears as shown below.
◆When playing a DVD VIDEO
Example:
Dolby Digital 5.1 ch
Rear (L/R)
If the player is set up to output the signal from
the DIGITAL OUT (COAXIAL) jack, the
surround effect will only be heard when
“DOLBY DIGITAL” is set to “D-PCM” and
“MPEG” is set to “PCM” in “AUDIO
SETUP” (page 57).
:
3 / 2 .1
ENGLISH DOLBY DIGITAL
1
Front (L/R) LFE (Low Frequency
+ Centre Effect)
Example:
Dolby Digital 3 ch
:
2 / 1
2 SPANISH DOLBY DIGITAL
SUR
Front (L/R)
Rear
(Monaural)
About audio signals
Audio signals recorded in a disc contain the
sound elements (channels) shown below.
Each channel is output from a separate
speaker.
• Front (L)
• Front (R)
• Centre
• Rear (L)
• Rear (R)
• Rear (Monaural): This signal can be either
the Dolby Surround Sound processed
signals or the Dolby Digital sound’s
monaural rear audio signals.
• LFE (Low Frequency Effect) signal
1
2
Press SUR during playback.
The following display appears.
TVS DYNAMIC THEATER
Press SUR repeatedly to select
one of the TVS sounds.
See the explanations given for each item
in the following section.
• TVS DYNAMIC THEATER
• TVS DYNAMIC
• TVS WIDE
• TVS NIGHT
Notes
• If “DTS” in “AUDIO SETUP” is set to “OFF,”
the DTS track selection option will not appear on
the screen even if the disc contains DTS tracks
(page 57).
• MPEG audio signals with more than two channels
will appear as shown above (3/2.1, 2/1), but only
the Front (L) and Front (R) signals will be output
from your two front speakers.
• TVS STANDARD
,continued
35
Download from Www.Somanuals.com. All Manuals Search And Download.
◆TVS NIGHT
To cancel the setting
Large sounds, such as explosions, are
suppressed, but quieter sounds are
unaffected. This feature is useful when you
want to hear the dialogue and enjoy the
surround sound effects of “TVS WIDE” at
low volume.
Select “OFF” in step 2.
◆TVS DYNAMIC THEATER
Creates one set of LARGE virtual rear
speakers and virtual subwoofer from the
sound of the front speakers (L, R) without
using actual rear speakers and subwoofer
(shown below).
This mode is effective when the distance
between the front L and R speakers is short,
such as with built-in speakers on a stereo TV.
◆TVS STANDARD
Creates three sets of virtual rear speakers
from the sound of the front speakers (L, R)
without using actual rear speakers (shown
below). Use this setting when you want to use
TVS with 2 separate speakers.
TV
L
R
Sub
woofer
◆TVS DYNAMIC
Creates one set of virtual rear speakers from
the sound of the front speakers (L, R) without
using actual rear speakers (shown below).
This mode is effective when the distance
between the front L and R speakers is short,
such as with built-in speakers on a stereo TV.
L: Front speaker (left)
R: Front speaker (right)
: Virtual speaker
TV
Notes
• When the playing signal does not contain a signal
for the rear speakers, you cannot hear the
surround effects.
• When you select one of the TVS modes, turn off
the surround setting of the connected TV or
amplifier (receiver).
• Make sure that your listening position is between
and at an equal distance from your speakers, and
that the speakers are located in similar
surroundings.
◆TVS WIDE
Creates five sets of virtual rear speakers from
the sound of the front speakers (L, R) without
using actual rear speakers (shown below).
This mode is effective when the distance
between the front L and R speakers is short,
such as with built-in speakers on a stereo TV.
• Not all discs will respond to the “TVS NIGHT”
function in the same way.
TV
• The TVS effects do not work when using the Fast
Play or Slow Play functions, even though you can
change the TVS modes.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying the Subtitles
Enjoying Movies
Changing the Angles
If subtitles are recorded on the discs, you can
change the subtitles or turn them on and off
whenever you want while playing a DVD.
If various angles (multi-angles) for a scene
are recorded on the DVD VIDEO, you can
change the viewing angle.
1
2
Press (subtitle) during
playback.
The following display appears.
1
2
Press
(angle) during playback.
The number of the angle appears on the
display.
1:ENGLISH
2
Press (subtitle) repeatedly to
select a setting.
◆ When playing a DVD VIDEO
Select the language.
Depending on the DVD VIDEO, the
choice of language varies.
Press
(angle) repeatedly to
select an angle number.
The scene changes to the selected angle.
When 4 digits are displayed, they
indicate a language code. See “Language
Code List” on page 64 to see which
language the code represents.
Note
Depending on the DVD VIDEO, you may not be
able to change the angles even if multi-angles are
recorded on the DVD VIDEO.
◆ When playing a DVD-VR mode disc
Select “ON.”
,continued
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Playback
Picture(CUSTOM PICTURE MODE)
To turn off the subtitles
Select “OFF” in step 2.
Notes
• Depending on the DVD VIDEO, you may not be
able to change the subtitles even if multilingual
subtitles are recorded on it. You also may not be
able to turn them off.
• While playing a disc with subtitles, the subtitle
may disappear when you press FAST PLAY or
SLOW PLAY button.
You can adjust the video signal of the DVD,
VIDEO CD or DATA CD/DATA DVD in
JPEG format from the player to obtain the
picture quality you want. Choose the setting
that best suits the programme you are
watching. When you select “MEMORY,”
you can make further adjustments to each
element of the picture (colour, brightness,
etc.).
ENTER
DISPLAY
RETURN
1
2
Press DISPLAY during playback
(When playing a DATA CD or DATA
DVD with JPEG image files, press
twice).
The Control Menu appears.
Press X/x to select
(CUSTOM PICTURE MODE), then
press ENTER.
The options for “CUSTOM PICTURE
MODE” appear.
(
)
)
1 2 2 7
(
1 8 3 4
DVD VIDEO
T
1 : 3 2 : 5 5
STANDARD
STANDARD
DYNAMIC 1
38
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Press X/x to select the setting you
want.
Adjusting the picture items in
“MEMORY”
The default setting is underlined.
• STANDARD: displays a standard
picture.
You can adjust each element of the picture
individually.
• PICTURE: changes the contrast
• BRIGHTNESS: changes the overall
brightness
• COLOR: makes the colours deeper or
lighter
• DYNAMIC 1: produces a bold
dynamic picture by increasing the
picture contrast and the colour
intensity.
• DYNAMIC 2: produces a more
dynamic picture than DYNAMIC 1 by
further increasing the picture contrast
and colour intensity.
• CINEMA 1: enhances details in dark
areas by increasing the black level.
• CINEMA 2: white colours become
brighter and black colours become
richer, and the colour contrast is
increased.
• HUE: changes the colour balance
1 In step 3 of “ Adjusting the Playback
Picture,” select“MEMORY” and press
ENTER.
The “PICTURE” adjustment bar appears.
• MEMORY: adjusts the picture in
greater detail.
PICTURE
0
4
Press ENTER.
The selected setting takes effect.
2 Press C/c to adjust the picture
contrast.
To go to the next or previous picture item
without saving the current setting, press
X/x.
z Hint
When you watch a movie, “CINEMA 1” or
“CINEMA 2” is recommended.
3 Press ENTER.
The adjustment is saved, and
“BRIGHTNESS” adjustment bar
appears.
4 Repeat step 2 and 3 to adjust
“BRIGHTNESS,” “COLOR,” and
“ HUE.”
To turn off the display
Press O RETURN , or DISPLAY.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Press ENTER.
Sharpening the Picture
The selected setting takes effect.
(SHARPNESS)
To cancel the “ SHARPNESS” setting
Select “OFF” in step 3.
You can enhance the outlines of images to
produce a sharper picture.
ENTER
DISPLAY
1
2
Press DISPLAY during playback
(When playing a DATA CD or DATA
DVD with JPEG image files, press
twice).
The Control Menu appears.
Press X/x to select
(SHARPNESS), then press ENTER.
The options for “SHARPNESS” appear.
(
)
)
1 2 2 7
(
1 8 3 4
DVD VIDEO
T
1 : 3 2 : 5 5
OFF
1
2
OFF
3
Press X/x to select a level.
• 1: enhances the outline.
• 2: enhances the outline more than 1.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Enjoying MP3 Audio and JPEG
Images
• The player will play any data with the extension
“.MP3,” “.JPG,” or “.JPEG,” even if they are not
in MP3 or JPEG format. Playing these data may
generate a loud noise which could damage your
speaker system.
• The player does not conform to audio tracks in
mp3PRO format.
• Some JPEG files cannot be played.
About MP3 Audio Tracks
and JPEG Image Files
MP3 is audio compression technology that
satisfies the ISO/IEC MPEG regulations.
JPEG is image compression technology.
You can play DATA CDs/DATA DVD that
contain MP3 audio tracks or JPEG image
files.
About playback order of albums,
tracks, and files
Albums play in the following order:
◆Structure of disc contents
Tree 1 Tree 2 Tree 3 Tree 4 Tree 5
DATA CDs/DATA DVDs that the
player can play
ROOT
You can play back DATA CDs (CD-ROMs/
CD-Rs/CD-RWs) or DATA DVDs (DVD-
ROMs/DVD+RWs/DVD+Rs/DVD-RWs/
DVD-Rs) recorded in MP3 (MPEG-1 Audio
Layer III) and JPEG format.
However, this player only plays DATA CDs
whose logical format is ISO 9660 Level 1/
Level 2 or Joliet, and DATA DVDs of
Universal Disk Format (UDF).
Refer to the instructions supplied with the
disc drives and the recording software (not
supplied) for details on the recording format.
Note
The player may not be able to play some DATA
CDs/DATA DVDs created in the Packet Write
format.
MP3 audio track or JPEG image
file that the player can play
Album Track or file
The player can play the following tracks and
files:
– MP3 audio tracks with the extension
“.MP3.”
– JPEG image files with the extension
“.JPEG” or “.JPG.”
– JPEG image files that conform to the DCF*
image file format.
* “Design rule for Camera File system”: Image
standards for digital cameras regulated by JEITA
(Japan Electronics and Information Technology
Industries Association).
,continued
41
Download from Www.Somanuals.com. All Manuals Search And Download.
When you insert a DATA CD/DATA DVD
and press H, the numbered tracks (or files)
are played sequentially, from 1 through 7.
Any sub-albums/tracks (or files) contained
within a currently selected album take
priority over the next album in the same tree.
(Example: C contains D so 4 is played
before 5.)
Playing MP3 Audio
Tracks or JPEG Image
Files
You can play MP3 audio tracks and JPEG
image files on DATA CDs (CD-ROMs/CD-
Rs/CD-RWs) or DATA DVDs (DVD-ROMs/
DVD+RWs/DVD+Rs/DVD-RWs/DVD-Rs).
When you press MENU and the list of album
names appears (page 43), the album names
are arranged in the following order:
A t B t C t D t F t G. Albums
that do not contain tracks (or files) (such as
album E) do not appear in the list.
PICTURE
NAVI
z Hints
CLEAR
• If you add numbers (01, 02, 03, etc.) to the front
of the track/file names when you store the tracks
(or files) in a disc, the tracks and files will be
played in that order.
• Since a disc with many trees takes longer to start
playback, it is recommended that you create
albums with no more than two trees.
MENU
ENTER
RETURN
ZOOM
Notes
• Depending on the software you use to create the
DATA CD/DATA DVD, the playback order may
differ from the above illustration.
• The playback order above may not be applicable
if there are more than 200 albums and 300 tracks/
files in each album.
z Hint
You can view the disc information while playing
• The player can recognize up to 200 albums (the
player will count just albums, including albums
that do not contain MP3 audio tracks and JPEG
image files). The player will not play any albums
beyond the 200th album.
Notes
• DATA CDs recorded in KODAK Picture CD
format automatically start playing when inserted.
• If no MP3 audio track or JPEG image file is
recorded on the DATA CD/DATA DVD, “No
audio data” or “No image data” appears on the
screen.
• Proceeding to the next or another album may take
some time.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting an album
Selecting an MP3 audio track
1 Press MENU.
1 After step 2 of “Selecting an album,”
press ENTER.
The list of albums on the disc appears.
When an album is being played, its title is
shaded.
The list of tracks in the album appears.
M Y F A V O U R I T E S O N G
(
)
1
2 5 6
(
)
3
3 0
W A L T Z F O R D E B B Y
M Y R O M A N C E
M I L E S T O N E S
M Y F U N N Y V A L E N T I N E
A U T U M L E A V E S
A L L B L U E S
R O C K B E S T H I T
K A R A O K E
M Y F A V O U R I T E S O N G
R & B
J A Z Z
C L A S S I C
S O M E D A Y M Y P R I N C E W...
S A L S A O F C U B A
B O S S A N O V A
2 Press X/x to select a track, and press
ENTER.
2 Press X/x to select the album you
Playback starts from the selected track.
want to play.
3 Press H.
Playback starts from the selected album.
To select MP3 audio tracks, see
To stop playback
Press x.
To go to the next or previous page
Press c or C.
To select JPEG image files, see
To return to the previous display
Press O RETURN.
To stop playback
Press x.
To go to the next or previous MP3 audio
track
Press > or . during playback. You can
select the first track of the next album by
pressing > during playback of the last
track of the current album.
Note that you cannot return to the previous
album by using ., and that you need to
select the previous album from the album list.
To go to the next or previous page
Press c or C.
To turn on or off the display
Press MENU repeatedly.
z Hint
Of the selected album, you can select to play only
the MP3 audio tracks, JPEG image files, or both, by
,continued
43
Download from Www.Somanuals.com. All Manuals Search And Download.
To rotate a JPEG image
Selecting a JPEG image file
Press X/x while viewing the image. Each
time you press X, the image rotates
counterclockwise by 90 degrees.
To return to normal view, press CLEAR.
Note that the view also returns to normal if
you press C/c to go to the next or previous
image.
1 After step 2 of “Selecting an album,”
press PICTURE NAVI.
The image files in the album appear in 16
subscreens. A scroll box is displayed on
the right.
Example: when X is pressed once.
Rotating direction
1
2
3
4
5
6
7
8
9
10
14
11
15
12
16
13
To display the additional image, select
the bottom images and press x. To return
to the previous image, select the top
images and press X.
To magnify a JPEG image (ZOOM)
Press ZOOM while viewing the image. You
can enlarge the image up to four times the
original size, and scroll using C/X/x/c.
To return to normal view, press CLEAR.
2 Press C/X/x/ctoselecttheimageyou
want to view, and press ENTER.
The selected image appears.
Example
◆When pressed once (x2)
The image enlarges twice the original size.
◆When pressed twice (x4)
The image enlarges four times the original
size.
To stop viewing the JPEG image
Press x.
z Hints
• While viewing JPEG image files, you can set
(page 40).
• You can view JPEG images files without MP3
audio by setting “MODE (MP3, JPEG)” to
“IMAGE (JPEG)” (page 45).
• The date the picture was taken is displayed beside
no date may appear depending on the digital
camera.
To go to the next or previous JPEG image
file
Press C or c during playback. You can select
the first file of the next album by pressing c
during playback of the last file of the current
album.
Note that you cannot return to the previous
album by using C, and that you need to select
the previous album from the album list.
Note
PICTURE NAVI does not work if “AUDIO (MP3)”
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing a slide show with sound
(MODE (MP3, JPEG))
Enjoying JPEG Images as
a Slide Show
When JPEG image files and MP3 audio
tracks are placed in the same album, you can
enjoy a slide show with sound.
You can play JPEG image files on a DATA
CD or DATA DVD successively as a slide
show.
1 Press DISPLAY during stop mode.
The Control Menu appears.
2 Press X/x to select
(MODE
(MP3, JPEG)), and press ENTER.
The options for “MODE (MP3, JPEG)”
appear.
(
)
)
1 2 2 7
(
1 8 3 4
DATA CD MP3
T
3 2 : 5 5
MENU
AUTO
AUTO
ENTER
DISPLAY
AUDIO (MP3)
IMAGE (JPEG)
3 Press X/x to select “AUTO” (default),
and press ENTER.
1
Press MENU.
• AUTO: plays both the JPEG image files
and MP3 audio tracks in the same
album as a slide show.
The list of albums on the DATA CD/
DATA DVD appears.
• AUDIO (MP3): plays only MP3 audio
tracks continuously.
(
)
3
3 0
• IMAGE (JPEG): plays only JPEG
image files continuously.
R O C K B E S T H I T
K A R A O K E
M Y F A V O U R I T E S O N G
R & B
J A Z Z
C L A S S I C
4 Press MENU.
The list of albums on the DATA CD/
DATA DVD appears.
S A L S A O F C U B A
B O S S A N O V A
(
)
3
3 0
2
3
Press X/x to select an album.
R O C K B E S T H I T
K A R A O K E
M Y F A V O U R I T E S O N G
R & B
J A Z Z
C L A S S I C
Press H.
The JPEG images in the selected album
start playing as a slide show.
S A L S A O F C U B A
B O S S A N O V A
5 Press X/x to select the album that
contains both the MP3 audio tracks
and JPEG images you want to play.
To stop playback
Press x.
Notes
6 Press H.
• The slide show stops when X/x or ZOOM is
pressed.To resume the slide show, press H.
• This function does not work if “MODE (MP3,
A slide show starts with sound.
,continued
45
Download from Www.Somanuals.com. All Manuals Search And Download.
z Hints
Setting the pace for a slide show
(INTERVAL)
• To repeat both MP3 audio tracks and JPEG image
files in a single album, repeat the same MP3 audio
track or album when “MODE (MP3, JPEG)” is set
to “AUTO.” See “Playing repeatedly (Repeat
• The player recognizes a maximum of 200 albums
regardless of the selected mode. Of each album,
the player recognizes up to 300 MP3 audio tracks
and 300 JPEG image files when “AUTO” is
selected, 600 MP3 audio tracks when “AUDIO
(MP3)” is selected, 600 JPEG image files when
“IMAGE (JPEG)” is selected.
You can set the time the slides are displayed
on the screen.
1 Press DISPLAY twice while viewing a
JPEG image or when the player is in
stop mode.
The Control Menu appears.
2 Press X/x to select
(INTERVAL), then press ENTER.
The options for “INTERVAL” appear.
Notes
• This function does not work if the MP3 audio
tracks and JPEG image files are not placed in the
same album.
• If playing time of JPEG image or MP3 audio is
longer than the other, the longer one continues
without sound or image.
• If you play large MP3 track data and JPEG image
data at the same time, the sound may skip. It is
recommended that you set the MP3 bit rate to 128
kbps or lower when creating the file. If the sound
still skips, then reduce the size of the JPEG file.
3 ( 1 2)
1(
4)
DATA CD JPEG
2 9 / 1 0 / 2 0 0 6
NORMAL
NORMAL
FAST
SLOW 1
SLOW 2
3 Press X/x to select a setting.
The default setting is underlined.
• NORMAL: sets the duration to between
6 to 9 seconds.
• FAST: sets a duration shorter than
NORMAL.
• SLOW 1: sets a duration longer than
NORMAL.
• SLOW 2: sets a duration longer than
SLOW 1.
4 Press ENTER.
Note
Some JPEG files, especially progressive JPEG files
or JPEG files of 3,000,000 pixels or more, may take
longer to display than others, which may make the
duration seem longer than the setting you selected.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Selectingtheslides’ appearance
(EFFECT)
You can select the way the slides are
displayed during a slide show.
1 Press DISPLAY twice while viewing a
JPEG image or when the player is in
stop mode.
2 Press X/xto select
(EFFECT),
then press ENTER.
The options for “EFFECT” appear.
3 ( 1 2)
1(
4)
DATA CD JPEG
2 9 / 1 0 / 2 0 0 6
MODE 1
MODE 1
MODE 2
MODE 3
MODE 4
MODE 5
OFF
3 Press X/x to select a setting.
The default setting is underlined.
• MODE 1: the image sweeps in from top
to bottom.
• MODE 2: the image sweeps in from left
to right.
• MODE 3: the image stretches out from
the centre of the screen.
• MODE 4: the images randomly cycle
through the effects.
• MODE 5: the next image slides over the
previous image.
• OFF: turns off this function.
4 Press ENTER.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Press X/x to select
(PARENTAL CONTROL), then press
ENTER.
Using Various Additional
Functions
The options for “PARENTAL
CONTROL” appear.
Locking Discs (CUSTOM
PARENTAL CONTROL, PARENTAL
CONTROL)
(
)
)
1 2 2 7
DVD VIDEO
(
1 8 3 4
T
1 : 3 2 : 5 5
ON
PLAYER
PASSWORD
OFF
You can set two kinds of playback restrictions
for a disc.
• Custom Parental Control
You can set playback restrictions so that the
player will not play inappropriate discs.
• Parental Control
4 Press X/x to select “ ON t,” then
press ENTER.
Playback of some DVD VIDEOs can be
limited according to a predetermined level
such as the age of the users. Scenes may be
blocked or replaced with different scenes.
The same password is used for both Parental
Control and Custom Parental Control.
◆ If you have not entered a password
The display for registering a new
password appears.
PARENTAL CONTROL
Enter a new 4-digit password,
ENTER
then press
.
Number
buttons
Enter a 4-digit password using the
number buttons, then press ENTER.
The display for confirming the password
appears.
ENTER
DISPLAY
◆ When you have already registered a
password
The display for entering the password
appears.
5 Enterorre-enteryour4-digitpassword
using the number buttons, then press
ENTER.
Custom Parental Control
“Custom parental control is set.” appears
and then the screen returns to the Control
Menu.
You can set the same Custom Parental
Control password for up to 40 discs. When
you set the 41st-disc, the first disc is
cancelled.
To turn off the Custom Parental Control
function
1 Insert the disc you want to lock.
If the disc is playing, press x to stop
playback.
1
2
3
Follow steps 1 to 3 of “Custom Parental
Control.”
Press X/x to select “OFF t,” then press
ENTER.
2 Press DISPLAY while the player is in
stop mode.
Enter your 4-digit password using the
number buttons, then press ENTER.
The Control Menu appears.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
To play a disc for which Custom Parental
Control is set
3 Press X/x to select “PLAYER t,”
then press ENTER.
◆ If you have not entered a password
The display for registering a new
password appears.
1
Insert the disc for which Custom Parental
Control is set.
The “CUSTOM PARENTAL
CONTROL” display appears.
PARENTAL CONTROL
CUSTOM PARENTAL CONTROL
Enter a new 4-digit password,
ENTER
then press
.
Custom parental control is already
set. To play, enter your password
ENTER
and press
.
Enter a 4-digit password using the
number buttons, then press ENTER.
The display for confirming the password
appears.
2
Enter your 4-digit password using the
number buttons, then press ENTER.
The player is ready for playback.
◆ When you have already registered a
password
The display for entering the password
appears.
z Hint
If you forget your password, enter the 6-digit
number “199703” using the number buttons when
the “CUSTOM PARENTAL CONTROL” display
asks you for your password, then press ENTER.
The display will ask you to enter a new 4-digit
password.
4 Enter or re-enteryour4-digitpassword
using the number buttons, then press
ENTER.
The display for setting the playback
limitation level appears.
Parental Control (limited
playback)
Playback of some DVD VIDEOs can be
limited according to a predetermined level
such as the age of the users. The
PARENTAL CONTROL
LEVEL:
STANDARD:
OFF
USA
“PARENTAL CONTROL” function allows
you to set a playback limitation level.
1 Press DISPLAY while the player is in
stop mode.
5 Press X/x to select “STANDARD,”
then press ENTER.
The Control Menu appears.
2 Press X/x to select
(PARENTAL CONTROL), then press
ENTER.
The selection items for “STANDARD”
are displayed.
The options for “PARENTAL
CONTROL” appear.
PARENTAL CONTROL
LEVEL:
STANDARD:
OFF
USA
USA
(
)
)
1 2 2 7
DVD VIDEO
(
1 8 3 4
OTHERS
T
1 : 3 2 : 5 5
ON
PLAYER
PASSWORD
OFF
6 Press X/x to select a geographic area
as the playback limitation level, then
press ENTER.
,continued
49
Download from Www.Somanuals.com. All Manuals Search And Download.
The area is selected.
Notes
When you select “OTHERS t,” select
and enter a standard code in the table on
page 64 using the number buttons.
• When you play discs which do not have the
Parental Control function, playback cannot be
limited on this player.
• Depending on the disc, you may be asked to
change the parental control level while playing
the disc. In this case, enter your password, then
change the level. If the Resume Play mode is
cancelled, the level returns to the previous level.
7 Press X/x to select “ LEVEL,” then
press ENTER.
The selection items for “LEVEL” are
displayed.
Changing the password
PARENTAL CONTROL
LEVEL:
STANDARD:
OFF
OFF
1 Press DISPLAY while the player is in
8:
7: NC17
stop mode.
6:
5:
R
The Control Menu appears.
2 Press X/x to select
(PARENTAL CONTROL), then press
ENTER.
8 Select the level you want using X/x,
then press ENTER.
The options for “PARENTAL
CONTROL” appear.
Parental Control setting is complete.
3 Press X/x to select “PASSWORD
t,” then press ENTER.
The display for entering the password
appears.
PARENTAL CONTROL
LEVEL:
STANDARD:
4: PG13
USA
4 Enter your 4-digit password using the
number buttons, then press ENTER.
The lower the value, the stricter the
limitation.
5 Enter a new 4-digit password using the
number buttons, then press ENTER.
6 To confirm your password, re-enter it
using the number buttons, then press
ENTER.
To turn off the Parental Control function
Set “LEVEL” to “OFF” in step 8.
To play a disc for which Parental Control is
set
If you make a mistake entering your
password
Press C before you press ENTER and input
the correct number.
1
Insert the disc and press H.
The display for entering your password
appears.
2
Enter your 4-digit password using the
number buttons, then press ENTER.
The player starts playback.
z Hint
If you forget your password, remove the disc and
repeat steps 1 to 3 of “Parental Control (limited
playback).” When you are asked to enter your
password, enter “199703” using the number
buttons, then press ENTER. The display will ask
you to enter a new 4-digit password. After you enter
a new 4-digit password, replace the disc in the
player and press H. When the display for entering
your password appears, enter your new password.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling other TVs with the
remote
Controlling Your TV With
the Supplied Remote
You can control the sound level, input source,
and power switch of non-Sony TVs as well.
If your TV is listed in the table below, set the
appropriate manufacturer’s code.
You can control the sound level, input source,
and power switch of your Sony TV with the
supplied remote.
1 While holding down TV [/1, press the
number buttons to select your TV’s
manufacturer’s code (see the table
below).
TV
Number
buttons
2 +/–
2 Release TV [/1.
t
Code numbers of controllable TVs
If more than one code number is listed, try
entering them one at a time until you find the
one that works with your TV.
Manufacturer Code number
Sony
01 (default)
Aiwa
01 (default)
You can control your TV using the buttons
below.
Grundig
Hitachi
JVC
11
24
By pressing
You can
33
TV [/1
Turn the TV on or off
LG
06
2 (volume) +/– Adjust the volume of the TV
Loewe
Panasonic
Philips
Samsung
Sanyo
06
t (TV/video) Switch the TV’s input source
between the TV and other
17, 49
06, 08
06, 71
25
input sources
Note
Depending on the connected unit, you may not be
able to control your TV using all or some of the
buttons on the supplied remote.
Sharp
29
Thomson
Toshiba
43
38
Notes
• When you replace the batteries of the remote, the
code number you have set may be reset to the
default setting. Set the appropriate code number
again.
• Depending on the unit being connected, you may
not be able to control your TV using all or some
of the buttons on the supplied remote.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Press X/x to select “ CUSTOM,”
then press ENTER.
Settings and Adjustments
The Setup Display appears.
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
Using the Setup Display
ENGLISH
ENGLISH
ORIGINAL
ENGLISH
By using the Setup Display, you can make
various adjustments to items such as picture
and sound. You can also set a language for the
subtitles and the Setup Display, among other
things.
For details on each Setup Display item, see
Press X/x to select the setup item
from the displayed list:
Note
“ LANGUAGE SETUP,” “ SCREEN
SETUP,” “ CUSTOM SETUP,” or
“ AUDIO SETUP.” Then press
ENTER.
Playback settings stored in the disc take priority
over the Setup Display settings and not all of the
functions described may work.
The Setup item is selected.
Example: “SCREEN SETUP”
Selected item
SCREEN SETUP
ENTER
TV TYPE:
16:9
ON
SCREEN SAVER:
BACKGROUND:
LINE:
DISPLAY
JACKET PICTURE
VIDEO
Setup items
1
2
Press DISPLAY when the player is
in stop mode.
5
Press X/x to select an item, then
press ENTER.
The Control Menu appears.
The options for the selected item appear.
Example: “TV TYPE”
Press X/x to select
(SETUP), then press ENTER.
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
LINE:
16:9
16:9
4:3 LETTER BOX
The options for “SETUP” appear.
4:3 PAN SCAN
(
)
DVD VIDEO
47
Options
QUICK
CUSTOM
RESET
QUICK
52
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Press X/x to select a setting, then
press ENTER.
Setting the Display or
Sound Track Language
(LANGUAGE SETUP)
The setting is selected and setup is
complete.
Example: “4:3 PAN SCAN”
Selected setting
“LANGUAGE SETUP” allows you to set
various languages for the on-screen display or
sound track.
SCREEN SETUP
TV TYPE:
4:3 PAN SCAN
ON
SCREEN SAVER:
BACKGROUND:
LINE:
JACKET PICTURE
VIDEO
Select “LANGUAGE SETUP” in the Setup
Display. To use the display, see “Using the
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
ENGLISH
ENGLISH
ORIGINAL
ENGLISH
To enter the Quick Setup mode
Select “QUICK” in step 3. Follow from step
5 of the Quick Setup explanation to make
◆ OSD (On-Screen Display)
Switches the display language on the screen.
To reset all of the “ SETUP” settings
1
Select “RESET” in step 3 and press
ENTER.
◆ MENU (DVD VIDEO only)
You can select the desired language for the
disc’s menu.
2
Select “YES” using X/x.
You can also quit the process and return
to the Control Menu by selecting “NO”
here.
◆ AUDIO (DVD VIDEO only)
Switches the language of the sound track.
When you select “ORIGINAL,” the language
given priority in the disc is selected.
3
Press ENTER.
57 return to the default settings. Do not
press [/1 while resetting the player,
which takes a few seconds to complete.
◆ SUBTITLE (DVD VIDEO only)
Switches the language of the subtitle recorded
on the DVD VIDEO.
When you select “AUDIO FOLLOW,” the
language for the subtitles changes according
to the language you selected for the sound
track.
z Hint
If you select “OTHERS t” in “MENU,”
“SUBTITLE,” or “AUDIO,” select and enter a
language code from “Language Code List” on
page 64 using the number buttons.
Note
If you select a language in “MENU,”
“SUBTITLE,” or “AUDIO” that is not recorded on
a DVD VIDEO, one of the recorded languages will
be automatically selected.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Settings for the Display
(SCREEN SETUP)
Depending on the DVD, “4:3 LETTER BOX” may
be selected automatically instead of “4:3 PAN
SCAN” or vice versa.
◆ SCREEN SAVER
Choose settings according to the TV to be
connected.
The screen saver image appears when you
leave the player in pause or stop mode for 15
minutes, or when you play a CD or DATA
CD (MP3 audio)/DATA DVD (MP3 audio)
for more than 15 minutes. The screen saver
will help prevent your display device from
becoming damaged (ghosting). Press H to
turn off the screen saver.
Select “SCREEN SETUP” in the Setup
Display. To use the display, see “Using the
The default settings are underlined.
SCREEN SETUP
TV TYPE:
16:9
ON
ON
Turns on the screen saver.
Turns off the screen saver.
SCREEN SAVER:
BACKGROUND:
LINE:
JACKET PICTURE
OFF
VIDEO
◆ BACKGROUND
Selects the background colour or picture on
the TV screen when the player is in stop mode
or while playing a CD or DATA CD (MP3
audio)/DATA DVD (MP3 audio).
◆ TV TYPE
Selects the aspect ratio of the connected TV
(4:3 standard or wide).
JACKET
PICTURE
The jacket picture (still picture)
appears, but only when the
jacket picture is already
16:9
Select this when you connect a
wide-screen TV or a TV with a
wide mode function.
recorded on the disc (CD-
EXTRA, etc.). If the disc does
not contain a jacket picture, the
“GRAPHICS” picture appears.
4:3
LETTER
BOX
Select this when you connect a
4:3 screen TV. Displays a wide
picture with bands on the upper
and lower portions of the
screen.
GRAPHICS A preset picture stored in the
player appears.
BLUE
The background colour is blue.
4:3
Select this when you connect a
BLACK
The background colour is
black.
PAN SCAN 4:3 screen TV. Automatically
displays the wide picture on the
entire screen and cuts off the
portions that do not fit.
◆ LINE
Selects video signals output from the LINE
(RGB)-TV jack on the rear panel of the
player.
16:9
VIDEO
S VIDEO
RGB
Outputs video signals.
Outputs S video signals.
Outputs RGB signals.
4:3 LETTER BOX
Notes
• If your TV does not accept S video or the RGB
signals, no picture will appear on the TV screen,
even if you select “S VIDEO” or “RGB.” Refer to
the instructions supplied with your TV.
4:3 PAN SCAN
• If your TV has only one SCART (EURO AV)
jack, do not select “S VIDEO.”
54
Download from Www.Somanuals.com. All Manuals Search And Download.
◆ PAUSE MODE (DVD VIDEO/DVD-VR
mode only)
Selects the picture in pause mode.
Custom Settings (CUSTOM
SETUP)
AUTO
The picture, including subjects
that move dynamically, is
output with no jitter. Normally
select this position.
Use this to set up playback related and other
settings.
FRAME
The picture, including subjects
that do not move dynamically,
is output in high resolution.
Select “CUSTOM SETUP” in the Setup
Display. To use the display, see “Using the
The default settings are underlined.
◆ TRACK SELECTION (DVD VIDEO only)
Gives the sound track which contains the
highest number of channels priority when you
play a DVD VIDEO on which multiple audio
formats (PCM, MPEG audio, DTS, or Dolby
Digital format) are recorded.
CUSTOM SETUP
AUTO POWER OFF:
AUTO PLAY:
PAUSE MODE:
TRACK SELECTION:
MULTI-DISC RESUME:
ON
OFF
AUTO
OFF
ON
OFF
No priority given.
Priority given.
AUTO
◆ AUTO POWER OFF
Switches the Auto Power Off setting on or
off.
Notes
• When you set the item to “AUTO,” the language
may change. The “TRACK SELECTION” setting
has higher priority than the “AUDIO” settings in
sound track is not played even if you set “TRACK
SELECTION” to “AUTO.”
ON
The player enters standby mode
when left in stop mode for more
than 30 minutes.
OFF
Switches this function off.
• If PCM, DTS, MPEG audio, and Dolby Digital
sound tracks have the same number of channels,
the player selects PCM, DTS, MPEG, and Dolby
Digital audio sound tracks in this order.
◆ AUTO PLAY
Switches the Auto Play setting on or off. This
function is useful when the player is
connected to a timer (not supplied).
◆ MULTI-DISC RESUME (DVD VIDEO/
VIDEO CD only)
Switches the Multi-disc Resume setting on or
off. Resume playback can be stored in
memory for up to 6 different DVD VIDEOs/
VIDEO CDs (page 21).
OFF
ON
Switches this function off.
Automatically starts playback
when the player is turned on by
a timer (not supplied).
ON
Stores the resume setting in
memory for up to 6 discs.
OFF
Does not store the resume
setting in memory. Playback
restarts at the resume point only
for the current disc in the player.
Note
If you run Quick Setup, Multi-disc Resume setting
stored in memory may return to the default settings.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
◆ DOWNMIX (DVD VIDEO/DVD-VR mode
only)
Settings for the Sound
(AUDIO SETUP)
Switches the method for mixing down to 2
channels when you play a DVD which has
rear sound elements (channels) or is recorded
in Dolby Digital format. For details on the
rear signal components, see “Checking the
audio signal format” (page 35). This function
affects the output of the following jacks:
– LINE (RGB)-TV jack
“AUDIO SETUP” allows you to set the sound
according to the playback and connection
conditions.
Select “AUDIO SETUP” in the Setup
Display. To use the display, see “Using the
– DIGITAL OUT (COAXIAL) jack when
“DOLBY DIGITAL” is set to “D-PCM”
The default settings are underlined.
AUDIO SETUP
DOLBY
SUR-
ROUND
Normally, select this position.
Multi-channel audio signals are
output to 2 channels for enjoying
surround sounds.
AUDIO DRC:
DOWNMIX:
DIGITAL OUT:
DOLBY DIGITAL:
MPEG:
DTS:
48kHz/96kHz PCM:
STANDARD
DOLBY SURROUND
ON
D-PCM
PCM
OFF
48kHz/16bit
NORMAL Multi-channel audio signals are
downmixed to 2 channels for use
with your stereo.
◆ AUDIO DRC (Dynamic Range Control)
(DVD VIDEO/DVD-VR mode only)
Makes the sound clear when the volume is
turned down when playing a DVD that
conforms to “AUDIO DRC.”
This function affects the output from the
following jacks:
– LINE (RGB)-TV jack
◆ DIGITAL OUT
Selects if audio signals are output via the
DIGITAL OUT (COAXIAL) jack.
ON
Normally select this position. When
you select “ON,” see “Setting the
digital output signal” for further
– DIGITAL OUT (COAXIAL) jack only
when “DOLBY DIGITAL” is set to “D-
OFF The influence of the digital circuit
upon the analog circuit is minimal.
STANDARD Normally select this position.
TV MODE
Makes low sounds clear even if
you turn the volume down.
WIDE
RANGE
Gives you the feeling of being
at a live performance.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
◆ DTS
Setting the digital output signal
Selects whether or not to output DTS signals.
Switches the method of outputting audio
signals when you connect a component such
as an amplifier (receiver) or MD deck with a
digital input jack.
OFF
Select this when the player is
connected to an audio
component without a built-in
DTS decoder.
Select “DOLBY DIGITAL,” “MPEG,”
“DTS,” and “48kHz/96kHz PCM” after
setting “DIGITAL OUT” to “ON.”
If you connect a component that is
incompatible with the selected audio signal, a
loud noise (or no sound) may be heard from
the speakers, risking damage to your ears or
speakers.
ON
Select this when the player is
connected to an audio
component with a built-in DTS
decoder.
◆ 48kHz/96kHz PCM (DVD VIDEO only)
Selects the sampling frequency of the audio
signal.
48kHz/16bit The audio signals of DVD
VIDEOs are always converted
to 48kHz/16bit.
◆ DOLBY DIGITAL (DVD VIDEO/DVD-VR
mode only)
Selects the type of Dolby Digital signal.
96kHz/24bit All types of signals including
96kHz/24bit are output in their
original format. However, if the
signal is encrypted for
D-PCM
Select this when the player is
connected to an audio
component without a built-in
Dolby Digital decoder. You can
select whether the signals
conform to Dolby Surround
(Pro Logic) or not by making
adjustments to the
copyright protection purposes,
the signal is only output as
48kHz/16bit.
Note
“DOWNMIX” item in
The analogue audio signals from the LINE (RGB)-
TV (SCART) jack is not affected by this setting and
keep their original sampling frequency level.
DOLBY
DIGITAL
Select this when the player is
connected to an audio
component with a built-in
Dolby Digital decoder.
◆ MPEG (DVD VIDEO/DVD-VR mode only)
Selects the type of MPEG audio signal.
PCM
Select this when the player is
connected to an audio
component without a built-in
MPEG decoder. If you play
MPEG audio sound tracks, the
player outputs stereo signals
via the DIGITAL OUT
(COAXIAL) jack.
MPEG
Select this when the player is
connected to an audio
component with a built-in
MPEG decoder.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
, When you are using a SCART cord, be sure
to use one that is fully wired (21-pins).
Additional Information
Sound
Troubleshooting
There is no sound.
, Re-connect the connecting cord securely.
, The connecting cord is damaged.
, The player is connected to the wrong input
jack on the amplifier (receiver) (page 16).
, The amplifier (receiver) input is not
correctly set.
If you experience any of the following
difficulties while using the player, use this
troubleshooting guide to help remedy the
problem before requesting repairs. Should
any problem persist, consult your nearest
Sony dealer.
, The player is in pause mode or in Slow-
motion Play mode.
, The player is in fast forward or fast reverse
mode.
Power
, If the audio signal does not come through
the DIGITAL OUT (COAXIAL) jack,
check the audio settings (page 56).
, While playing a Super VCD on which the
audio track 2 is not recorded, no sound will
come out when you select “2:STEREO,”
“2:1/L,” or “2:2/R.”
, When playing multichannel MPEG audio
soundtracks, only the Front (L) and Front
(R) signal will be output from your two
front speakers.
The power is not turned on.
, Check that the mains lead is connected
securely.
Picture
There is no picture/picture noise appears.
, Re-connect the connecting cord securely.
, The connecting cords are damaged.
and switch the input selector on your TV so
that the signal from the player appears on
the TV screen.
, Set “LINE” in “SCREEN SETUP” to an
, The disc is dirty or flawed.
, If the picture output from your player goes
through your VCR to get to your TV or if
you are connected to a combination TV/
VIDEO player, the copy-protection signal
applied to some DVD programmes could
affect picture quality.
The sound volume is low.
, The sound volume is low on some DVDs.
The sound volume may improve if you set
“AUDIO DRC” in “AUDIO SETUP” to
“TV MODE” (page 56).
Operation
The remote does not function.
, The batteries in the remote are weak.
, There are obstacles between the remote and
the player.
, The disc is recorded in a colour system that
is different from your TV.
, The distance between the remote and the
player is too far.
, The remote is not pointed at the remote
sensor on the player.
The picture does not fill the screen, even
though the aspect ratio is set in “ TV TYPE”
under “ SCREEN SETUP.”
, The aspect ratio of the disc is fixed on your
DVD.
The disc does not play.
, The disc is turned over.
Insert the disc with the playback side facing
down.
, The disc is skewed.
, The player cannot play certain discs
(page 6).
The picture is black and white.
, Set “LINE” in “SCREEN SETUP” to an
, Depending on the TV, the picture on the
screen becomes black and white when you
play a disc recorded in the NTSC colour
system.
, The region code on the DVD does not match
the player.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
, Moisture has condensed inside the player
, The player cannot play a recorded disc that
The disc does not start playing from the
beginning.
, Programme Play, Shuffle Play, Repeat Play,
or A-B Repeat Play is selected (page 24).
.
.
The MP3 audio track cannot be played
(page 42).
, The DATA CD is not recorded in an MP3
format that conforms to ISO 9660 Level 1/
Level 2 or Joliet.
, The DATA DVD is not recorded in MP3
format that conform to UDF (Universal
Disk Format).
The player starts playing the disc
automatically.
, The disc features an auto playback function.
, “AUTO PLAY” in “CUSTOM SETUP” is
set to “ON” (page 55).
, The MP3 audio track does not have the
extension “.MP3.”
, The data is not formatted in MP3 even
though it has the extension “.MP3.”
, The data is not MPEG-1 Audio Layer III
data.
Playback stops automatically.
, While playing discs with an auto pause
signal, the player stops playback at the auto
pause signal.
, The player cannot play audio tracks in
Some functions suchas Stop, Search, Fast
Play and Slow Play, Slow-motion Play,
Repeat Play, Shuffle Play, or Programme
mp3PRO format.
, “MODE (MP3, JPEG)” is set to “IMAGE
Play cannot be performed.
, Depending on the disc, you may not be able
to do some of the operations above. Refer to
the operating manual that comes with the
disc.
The JPEG image file cannot be played
(page 42).
, The DATA CD is not recorded in a JPEG
format that conforms to ISO 9660 Level 1/
Level 2, or Joliet.
, The DATA DVD is not recorded in JPEG
format that conforms to UDF (Universal
Disk Format).
The language for the sound track cannot
be changed.
, Try using the DVD’s menu instead of the
direct selection button on the remote
, Multilingual tracks are not recorded on the
DVD being played.
, The file has an extension other than
“.JPEG” or “.JPG.”
, The image is larger than 3072 (width) ×
2048 (height) in normal mode, or more than
3,300,000 pixels in progressive JPEG.
(Some progressive JPEG files cannot be
displayed even if the file size is within this
specified capacity.)
, The DVD prohibits the changing of the
language for the sound track.
The subtitle language cannot be changed
, The image does not fit the screen (the image
is reduced).
, “MODE (MP3, JPEG)” is set to “AUDIO
or turned off.
, Try using the DVD’s menu instead of the
direct selection button on the remote
, Multilingual subtitles are not recorded on
the DVD being played.
, The DVD prohibits the changing of
subtitles.
The MP3 audio tracks and JPEG image
files start playing simultaneously.
, “MODE (MP3, JPEG)” is set to “AUTO”
The angles cannot be changed.
, Try using the DVD’s menu instead of the
direct selection button on the remote
, Multi-angles are not recorded on the DVD
being played.
The album/track/file names are not
displayed correctly.
, The player can only display numbers and
alphabet. Other characters are displayed as
“ ”.
*
,continued
59
Download from Www.Somanuals.com. All Manuals Search And Download.
, The DVD prohibits changing of the angles.
Self-diagnosis Function
(When letters/numbers appear in the
display)
The player does not operate properly.
, When static electricity, etc., causes the
player to operate abnormally, unplug the
player.
When the self-diagnosis function is activated
to prevent the player from malfunctioning, a
five-character service number (e.g., C 13 50)
with a combination of a letter and four digits
appears on the screen. In this case, check the
following table.
5 numbers or letters are displayed on the
screen.
, The self-diagnosis function was activated.
The disc tray does not open.
, Contact your Sony dealer or local
authorized Sony service facility.
C:13:50
“ Data error” appears on the TV screen
when playing a DATA CD or DATA DVD.
, The MP3 audio track/JPEG image file you
want to play is broken.
, The data is not MPEG-1 Audio Layer III
data.
First three
characters of action
the service
Cause and/or corrective
number
, The JPEG image file format does not
, The JPEG image file has the extension
“.JPG” or “.JPEG,” but is not in JPEG
format.
C 13
The disc is dirty or recorded
in a format that this player
,Clean the disc with a
cleaning cloth or check its
C 31
E XX
The disc is not inserted
correctly.
,Re-insert the disc
correctly.
To prevent a malfunction, the
(xx is a number) player has performed the
self-diagnosis function.
,Contact your nearest
Sony dealer or local
authorized Sony service
facility and give the 5-
character service number.
Example: E 61 10
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
A disc that contains up to 8 hours of moving
pictures even though its diameter is the same
as a CD.
The data capacity of a single-layer and single-
sided DVD is 4.7 GB (Giga Byte), which is 7
times that of a CD. The data capacity of a
double-layer and single-sided DVD is 8.5
GB, a single-layer and double-sided DVD is
9.4 GB, and double-layer and double-sided
DVD is 17 GB.
A unit in which to store JPEG image files or
MP3 audio tracks on a DATA CD/DATA
DVD. (“Album” is an exclusive definition for
this player.)
Chapter
The picture data uses the MPEG 2 format, a
worldwide standard of digital compression
technology. The picture data is compressed to
about 1/40 (average) of its original size. The
DVD also uses a variable rate coding
technology that changes the data to be
allocated according to the status of the
picture. Audio information is recorded in a
multi-channel format, such as Dolby Digital,
allowing you to enjoy a more realistic audio
presence.
Sections of a picture or a music feature that
are smaller than titles. A title is composed of
several chapters. Depending on the disc, no
chapters may be recorded.
Digital audio compression technology
developed by Dolby Laboratories. This
technology conforms to multi-channel
surround sound. The rear channel is stereo
and there is a discrete subwoofer channel in
this format. Dolby Digital provides the same
discrete channels of high quality digital audio
found in “Dolby Digital” theatre surround
sound systems. Good channel separation is
realized because all of the channel data is
recorded discretely and little deterioration is
realized because all channel data processing
is digital.
Furthermore, various advanced functions
such as the multi-angle, multilingual, and
Parental Control functions are provided with
the DVD.
A DVD-RW is a recordable and rewritable
disc that is the same size as a DVD VIDEO.
The DVD-RW has two different modes: VR
mode and Video mode. DVD-RWs created in
Video mode have the same format as a DVD
VIDEO, while discs created in VR (Video
Recording) mode allow the contents to be
programmed or edited.
Digital audio compression technology that
Digital Theater Systems, Inc. developed. This
technology conforms to multi-channel
surround sound. The rear channel is stereo
and there is a discrete subwoofer channel in
this format. DTS provides the same discrete
channels of high quality digital audio.
Good channel separation is realized because
all of the channel data is recorded discretely
and little deterioration is realized because all
channel data processing is digital.
A DVD+RW (plus RW) is a recordable and
rewritable disc. DVD+RWs use a recording
format that is comparable to the DVD VIDEO
format.
A JPEG image recorded on a DATA CD/
DATA DVD (“File” is an exclusive
definition for this player). A single file
consist of a single image or video.
,continued
61
Download from Www.Somanuals.com. All Manuals Search And Download.
International standard coding system used to
compress audio digital signals authorized by
ISO/IEC. MPEG 1 conforms to up to 2-
channel stereo. MPEG 2, used on DVDs,
conforms to up to 7.1-channel surround.
Title
The longest section of a picture or music
feature on a DVD, movie, etc., in video
software, or the entire album in audio
software.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
System
General
Laser: Semiconductor laser
Signal format system: PAL/(NTSC)
Power requirements:
220 – 240 V AC, 50/60 Hz
Power consumption: 8 W
Dimensions (approx.): 430 × 43 × 207 mm
(width/height/depth) incl. projecting
parts
Mass (approx.): 1.69 kg
Operating temperature: 5 °C to 35 °C
Operating humidity: 25 % to 80 %
Audio characteristics
Frequency response: DVD VIDEO (PCM
48 kHz): 2 Hz to 22 kHz (±0.5 dB)/CD:
2 Hz to 20 kHz (±0.5 dB)
Harmonic distortion: 0.01 %
Dynamic range: DVD VIDEO: 85 dB/CD:
85 dB
Supplied accessories
Wow and flutter: Less than detected value
(±0.001% W PEAK)
Output
Specifications and design are subject to
change without notice.
(Jack name: Jack type/Output level/Load
impedance)
DIGITAL OUT (COAXIAL): Phono jack/
0.5 Vp-p/75 ohms
LINE (RGB)-TV:
(AUDIO): SCART jack/2 Vrms/10 kilohms
(VIDEO): SCART jack/1.0 Vp-p/75 ohms
(S VIDEO): SCART jack/Y: 1.0 Vp-p,
C: 0.3 Vp-p (PAL), 0.286 Vp-p (NTSC)/
75 ohms
(RGB): SCART jack/0.7 Vp-p/75 ohms
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Language Code List
The language spellings conform to the ISO 639: 1988 (E/F) standard.
Code Language
Code Language
Code Language
Code Language
1027 Afar
1183 Irish
1347 Maori
1507 Samoan
1508 Shona
1509 Somali
1511 Albanian
1512 Serbian
1513 Siswati
1514 Sesotho
1515 Sundanese
1516 Swedish
1517 Swahili
1521 Tamil
1028 Abkhazian
1032 Afrikaans
1039 Amharic
1044 Arabic
1045 Assamese
1051 Aymara
1052 Azerbaijani
1053 Bashkir
1057 Byelorussian
1059 Bulgarian
1060 Bihari
1061 Bislama
1066 Bengali;
Bangla
1067 Tibetan
1070 Breton
1079 Catalan
1093 Corsican
1097 Czech
1103 Welsh
1105 Danish
1109 German
1130 Bhutani
1142 Greek
1144 English
1145 Esperanto
1149 Spanish
1150 Estonian
1151 Basque
1157 Persian
1165 Finnish
1166 Fiji
1186 Scots Gaelic
1194 Galician
1196 Guarani
1203 Gujarati
1209 Hausa
1349 Macedonian
1350 Malayalam
1352 Mongolian
1353 Moldavian
1356 Marathi
1357 Malay
1358 Maltese
1363 Burmese
1365 Nauru
1217 Hindi
1226 Croatian
1229 Hungarian
1233 Armenian
1235 Interlingua
1239 Interlingue
1245 Inupiak
1248 Indonesian
1253 Icelandic
1254 Italian
1257 Hebrew
1261 Japanese
1269 Yiddish
1283 Javanese
1287 Georgian
1297 Kazakh
1298 Greenlandic
1299 Cambodian
1300 Kannada
1301 Korean
1305 Kashmiri
1307 Kurdish
1311 Kirghiz
1369 Nepali
1376 Dutch
1525 Telugu
1527 Tajik
1528 Thai
1379 Norwegian
1393 Occitan
1403 (Afan)Oromo
1408 Oriya
1417 Punjabi
1428 Polish
1435 Pashto;
Pushto
1436 Portuguese
1463 Quechua
1481 Rhaeto-
Romance
1482 Kirundi
1483 Romanian
1489 Russian
1491 Kinyarwanda
1495 Sanskrit
1498 Sindhi
1501 Sangho
1502 Serbo-
Croatian
1529 Tigrinya
1531 Turkmen
1532 Tagalog
1534 Setswana
1535 Tonga
1538 Turkish
1539 Tsonga
1540 Tatar
1543 Twi
1557 Ukrainian
1564 Urdu
1572 Uzbek
1581 Vietnamese
1587 Volapük
1613 Wolof
1632 Xhosa
1665 Yoruba
1684 Chinese
1697 Zulu
1313 Latin
1326 Lingala
1327 Laothian
1332 Lithuanian
1334 Latvian;
Lettish
1171 Faroese
1174 French
1181 Frisian
1503 Singhalese
1505 Slovak
1506 Slovenian
1345 Malagasy
1703 Not specified
Parental Control Area Code List
For details, see page 49.
Code Area
Code Area
Code Area
Code Area
2044 Argentina
2047 Australia
2046 Austria
2057 Belgium
2070 Brazil
2079 Canada
2090 Chile
2092 China
2165 Finland
2174 France
2109 Germany
2248 India
2238 Indonesia
2254 Italy
2276 Japan
2304 Korea
2363 Malaysia
2362 Mexico
2149 Spain
2376 Netherlands
2390 New Zealand
2379 Norway
2427 Pakistan
2424 Philippines
2436 Portugal
2489 Russia
2499 Sweden
2086 Switzerland
2528 Thailand
2184 United
Kingdom
2115 Denmark
2501 Singapore
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
DVD’s menu 22
Numerics
Q
16:9 54
QUICK 53
4:3 LETTER BOX 54
4:3 PAN SCAN 54
48kHz/96kHz PCM 57
5.1 Channel Surround 16
E
R
EFFECT 47
REPEAT 26
Repeat Play 26
Replay 20
F
A
Fast forward 28
FAST PLAY 20
Fast reverse 28
FILE 30
A-B REPEAT 27
Advance 20
RESET 53
ALBUM 30
S
File 61
Freeze Frame 29
Scan 28
Angle 37
SCENE 30
AUDIO DRC 56
AUDIO SETUP 56
AUTO PLAY 55
AUTO POWER OFF 55
SCREEN SAVER 54
SCREEN SETUP 54
Searching 28
SETUP 52
Setup Display 52
SHARPNESS 40
SHUFFLE 25
Shuffle Play 25
Slide Show 45
SLOW PLAY 20
Slow-motion Play 29
Speakers
H
Handling discs 2
Hooking up 13
I
B
INDEX 29
BACKGROUND 54
Batteries 13
INTERVAL 46
J
C
L
CHAPTER 29
Chapter 61
LANGUAGE SETUP 53
LINE 54
Hooking up 16
SUBTITLE 53
Surround 35
CHAPTER VIEWER 31
Checking the audio signal
format 35
Child Lock 20
Connecting 14
Continuous play
CD/VIDEO CD 19
DVD 19
Control Menu 10
CUSTOM 52
CUSTOM PARENTAL
CONTROL 48
CUSTOM PICTURE MODE
Locating
a specific point by watching
the TV screen 28
T
M
TITLE 29
MEMORY 39
MENU 53
Title 62
TITLE VIEWER 31
TOP MENU 22
TRACK 29
TRACK SELECTION 55
TRACK VIEWER 31
Troubleshooting 58
TV TYPE 54
MODE (MP3, JPEG) 45
O
On-screen display
Control Menu Display 10
Setup Display 52
ORIGINAL 22
ORIGINAL/PLAY LIST 22
OSD 53
CUSTOM SETUP 55
TVS (TV Virtual Surround)
D
DATE 44
U
Usable discs 6
V
DIGITAL OUT 56
Digital output 57
Display
Control Menu Display 10
Setup Display 52
DOWNMIX 56
P
PARENTAL CONTROL 48
PAUSE MODE 55
PBC Playback 23
PICTURE NAVIGATION
Z
PLAY LIST 22
PROGRAM 24
Programme Play 24
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed on 100% recycled paper using
VOC (Volatile Organic Compound)-free
vegetable oil based ink.
Sony Corporation Printed in Malaysia
Download from Www.Somanuals.com. All Manuals Search And Download.
|