3-225-952-11 (1)
Co rd le ss
Te le p h o n e
US
Operating Instructions
SPP-S2430
©2000 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
If your telephone is equipped
w ith automatic dialers
When programming emergency numbers and
(or) making test calls to emergency numbers:
INFORMATION FOR
GENERAL TELEPHONES
1. This equipment complies with Part 68 of the
FCC rules. On the bottom of this equipment
is a label that contains, among other
information, the FCC certification number and
ringer equivalence number (REN) for this
equipment. If requested, this information
must be provided to the telephone company.
1. Remain on the line and briefly explain to
the dispatcher the reason for the call.
2. Perform such activities in the off-peak
hours, such as early morning or late
evenings.
2. The applicable certification jack (connector)
USOC-RJ11C is used for this equipment.
Caution
3. This equipment is designed to be connected to
the telephone network or premises wiring
using a compatible modular jack that is Part
68 compliant.
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate this
equipment.
The FCC compliant telephone cord and
modular plug is provided with this
equipment.
Note
4. The REN is used to determine the quantity of
devices that may be connected to the
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
telephone line. Excessive RENs on the
telephone line may result in the devices not
ringing in response to an incoming call.
Typically, the sum of the RENs should not
exceed five (5.0).To be certain of the number
of devices that may be connected to a line, as
determined by the total RENs, contact the
local telephone company.
5. If this equipment (SPP-S2430) causes harm to
the telephone network, the telephone
company will notify you in advance that
temporary discontinuance of service may be
required. But if advance notice isn’t practical,
the telephone company will notify the
customer as soon as possible. Also, you will
be advised of your right to file a complaint
with the FCC if you believe it is necessary.
6. The telephone company may make changes in
its facilities, equipment, operations or
– Reorient or relocate the receiving antenna.
procedures that could affect the operation of
the equipment. If this happens the telephone
company will provide advance notice so you
can make necessary modifications to maintain
uninterrupted service.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
7. If trouble is experienced with this equipment
(SPP-S2430), for repair or warranty
– Consult the dealer or an experienced radio/
TV technician for help.
information, please contact Sony Direct
Response Center: Tel 1-800-222-7669. If the
equipment is causing harm to the telephone
network, the telephone company may request
that you disconnect the equipment until the
problem is resolved.
8. All repairs will be performed in an authorized
Sony service station.
9. This equipment cannot be used to party lines
or coin lines.
10.This equipment is hearing aid compatible.
3US
Download from Www.Somanuals.com. All Manuals Search And Download.
Ta b le o f co n t e n t s
46
48
Making calls from the Phone
Ge t t in g St a rt e d
7
Transferring the Phone
Step 1: Checking the package
50 Switching the phones during a
11 Step 3: Preparing the battery
50
50
To switch from the base
handset
17 Step 5: Setting up the phone
To switch from the cordless
51 Talking between the phones
51
52
To talk from the cordless
To talk from the base phone
to the cordless handset
Ba sics
53
To transfer from the base
handset
54
To transfer from the cordless
Te le p h o n e Fe a t u re s
Ca lle r ID Fe a t u re s
39
41
42
Storing phone numbers and
Changing a stored name
service
Making calls with one-touch
57
Erasing data from the
Caller ID list
43
44
Storing phone numbers and
names
59 Calling back a number from
the Caller ID list
Changing a stored name
4US
Table of contents
Download from Www.Somanuals.com. All Manuals Search And Download.
61
62
Storing a number of the
Directory
To change the number of
64 Using “Caller ID with call
Ad d it io n a l In fo rm a t io n
67 Mounting the base phone on a
wall
68 Carrying the cordless handset by
the belt clip
5US
Table of contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Ge t t in g St a rt e d
Re a d t h is first
Before you use your phone, you must first set it up. Here’s a quick way
to set up your phone: Steps 1 to 6.
St e p 1
(p a g e 7)
First,unpack thephoneand thesupplied accessories.
St e p 2
(p a g e s 8 t o 10)
You need todothreethingstosetup the
basephone,includingfindingthebest
location forthebasephone.
St e p 3
(p a g e s 11 t o 12)
Insertthebatterypackintothecordless
handsetand chargeitfor morethan 12
hours.
Base phone
St e p 4
(p a g e s 13 t o 16)
Enter thearea codeto usetheCaller ID
service.
St e p 5
(p a g e s 17 t o 21)
Set up the “Caller ID with callwaiting”
service,theLongDistanceSaver function
and thevoicemailservice.
St e p 6
(p a g e s 22 t o 23)
Finally,set theday and time.
Cordless handset
Th a t ’s it !
6US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 1
Ch e ckin g t h e p a cka g e co n t e n t s
Make sure you have received the following items in the package.
If anything is missing, contact your local Sony dealer.
Base phone
AC pow er adaptor (AC-T107)
Cordless handset
Charger
Handset
Handset cord
Belt clip
Telephone
line cords (2)
Wall bracket/
stand for base
phone
Rechargeable
battery pack
(BP-T24)
7US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 2
Se t t in g u p t h e b a se p h o n e
Do the following steps:
• Choose the best location
• Connect the base phone
• Choose the dialing mode
Ch o o se t h e b e st lo ca t io n
Where you place the base phone affects the reception quality of the
cordless handset.
Aw ay from noise sources such as a w indow
by a street w ith heavy traffic
Aw ay from television
sets and other
electronic equipment
Aw ay from heat sources, such as radiators,
airducts, and sunlight
Aw ay from a microw ave
oven
Aw ay from excessive
moisture, extremely low
temperatures, dust,
mechanical vibration, or
shock
Aw ay from a personal
computer
Ne a r a ce n t ra l lo ca t io n
a n d o n a le ve l su rfa ce
Aw ay from another
cordless telephone
CAUTION: • Should you experience intermittent loss of audio during a conversation, try
moving closer to the base or move base phone aw ay from other noise sources.
• The cordless telephone operates at a frequency that may cause interference to
nearby TVs and VCRs; the base phone should not be placed near or on the top
of a TV or VCR; and, if interference is experienced, moving the cordless
telephone farther aw ay from the TV or VCR w ill often reduce or eliminate the
interference.
8US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Co n n e ct t h e b a se p h o n e
If you want to hang the base phone on the wall, see page 67.
1
4
Hook the cord.
To
HANDSET
To DC IN 11V
To an AC outlet
3
AC pow er adaptor
(supplied
To LINE
AC-T107)
Telephone line cord
(supplied)
2 To a telephone
outlet
1
2
3
4
Connectthehandsetcord tothe
HANDSET jack and to the
handset.
To tilt the phone
If you want to tilt the phone, attach the
supplied wall bracket on the bottom of
the base phone.
Connectthetelephonelinecord
to the LINE jack and to a
telephoneoutlet.
2
1
Align the
f marks.
ConnecttheACpower adaptor
to the DC IN 11V jack and to an
ACoutlet.
Raisetheantenna.Makesureit
pointstowardstheceiling.
co n t in u e d
Getting Started
9US
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 2: Se t t in g u p t h e b a se p h o n e (co n t in u e d )
Notes
•
•
•
Use only the supplied AC-T107 AC power adaptor.
Do not use any other AC power adaptor.
Connect the AC power adaptor to a continuous power
supply.
Place the base phone close to the AC outlet so that
you can unplug the AC power adaptor easily.
Polarity of the plug
–
+
Tip
Modular
If your telephone outlet is not modular, contact your
telephone service company for assistance.
Ch o o se t h e d ia lin g m o d e
For the telephone to work properly, select an appropriate dialing mode
(tone or pulse).
DIAL MODE sw itch
Depending on your dialing system, set the DIAL MODE switch as
follows:
If your dialing system is
Set the sw itch to
Tone
Pulse
T
P
If you aren't sure of your dialing system
Make a trial call with the DIAL MODE switch set to T.
If the call connects, leave the switch as is; otherwise, set to P.
10US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 3
Pre p a rin g t h e b a t t e ry p a ck
Charge the battery pack for more than 12 hours before you start using
your cordless handset.
1
2
Slideopen thebattery
compartmentlid ofthecordless
handset.
BP-T24
Connectthebatteryconnector
with correctpolarity (black wire
goeson lower sideand red wire
goeson upper side).
Red
Black
3
4
Hook thecordsand insertthe
battery pack.Then closethelid.
Hook
Connect the AC power adaptor
to an AC outlet and place the
cordless handset on the charger .
The CHARGE lamp on the
charger lightsup when the
cordlesshandsetisproperly
seated on thechargeterminals
ofthecharger.Chargethe
batterypackfor morethan 12
hours sothatthebattery isfully
charged. The CHARGE lamp
remainsliteven aftercharging
iscompleted.
To an AC outlet
Front side
CHARGE lamp
co n t in u e d
11US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 3: Pre p a rin g t h e b a t t e ry p a ck (co n t in u e d )
Battery duration
A fully charged battery pack lasts for about:
• Approx. 6 hours when you use the cordless handset continuously
• Approx. 6 days when the cordless handset is in standby mode.
Notes
•
The battery pack will gradually discharge over a long period of time, even
when not in use.
•
If you leave the battery pack in the cordless handset without charging it, the
battery pack will be completely discharged.
It may require several times of charging to recover to its full capacity.
While charging, the battery pack warms up. This is not a malfunction.
•
To obtain the best performance from the battery
Do not place the cordless handset on the charger after each call. The
battery works best if the cordless handset is returned to the charger
after two or three calls. However, do not leave the cordless handset off
the charger for a long period of time as this will completely discharge
the battery pack.
When to purchase a new battery pack
If the battery lasts only a few minutes even after 12 hours of charging,
the usable life of the battery has expired and needs replacement.
Contact your local Sony authorized dealer or service center, and ask
for a Sony BP-T24 rechargeable battery pack.
Note
Battery life may vary depending on usage condition and ambient temperature.
12US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 4
En t e rin g t h e a re a co d e
When you use this phone for the first time, or move to an area that has a
different area code, you must enter the area code. Otherw ise, you cannot use
some functions of this phone and the Caller ID functions.
This is also necessary because the phone must be able to select an area code to
properly dial a call from the Caller ID list.
Depending on your region, enter the 3-digit area code as follows:
Case 1.
If 7-digit dialing (no area code) is accepted for local calls in your area, see “To enter
your home area code” below.
If you live in an area where calls from or to other local areas can also be made by 10-digit dialing
(area code + number), you can register up to 5 local area codes with this telephone to take
advantage of this system. See “To enter the local area code (For 10 digits phone number users)”
on page 15.
Case 2.
If 10-digit dialing (area code + number) is required for all local calls in your area, see
“To enter the local area code (For 10 digits phone number users)” on page 15.
Entering the area code is only possible on the base phone.
To e n t e r yo u r h o m e a re a co d e
1
2
Press (PROGRAM).
(ERASE)
Turn Jog Dial to choose “BASE
SETTINGS”, and then press Jog
Button (ENTER).
BASE SETTINGS
GO BACK
Jog Button
(ENTER)
AREA CODE
PHONE SERVICES
MESSAGES LAMP
3
Press Jog Button (ENTER).
AREA CODE
GO BACK
HOME :
LOCAL 1:
LOCAL 2:
co n t in u e d
Getting Started
13US
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 4: En t e rin g t h e a re a co d e (co n t in u e d )
4
Press Jog Button (ENTER) again.
ENTER HOME
AREA CODE.
“ENTER HOME AREA CODE.” appears on
the display.
_
5
6
Enter the three digits of your home area code
using the dialing keys.
Press (PROGRAM).
You hear a long confirmation beep.
Notes
•
If the home area code is already entered, it appears on the display in step 3.
To enter a different home area code, see “To change the home area code”
below.
•
•
Do not allow more than 20 seconds to elapse during the operation procedure.
If the area code has not been entered, calling back from the Caller ID list and
storing the Caller ID data into the Phone Directory cannot be performed.
•
If the home area code is not correctly entered, “SEND TO CORDLESS
HANDSET FAILED.” will appear on the display and five short error beeps
will be heard after (PROGRAM) is pressed in step 6. Move the cordless
handset closer to the base phone, and then start over the procedure.
Tips
•
When you select “[GO BACK]”, you can return to the previous set display by
pressing Jog Button (ENTER).
•
•
You may press Jog Button (ENTER) instead of (PROGRAM) in step 6.
To check the current home area code, perform steps 1 to 3. The home area
code appears on the display for about 20 seconds.
To change the home area code
1 Perform steps1to4on pages13to14.
Thecurrenthomearea codeappearson thedisplay.
2 Press (ERASE)toerasethecurrenthomearea code.
3 Enter a new homearea codeusing thedialing keys.
4 Press (PROGRAM).
You hearalongconfirmation beep.
To erase the home area code
You can erase the home area code. Perform steps 1 and 2 above, then
press (PROGRAM).
The home area code will be erased, and you hear a long confirmation
beep.
14US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
To e n t e r t h e lo ca l a re a co d e (Fo r 10 d ig it s
p h o n e n u m b e rs u se rs)
If a call matches one of the local area codes you entered, the phone
number will be registered with 10 digits in the Caller ID list (area code
+ number). If a call does not match one of the local area codes you
entered, the phone number will be registered with 11 digits in the
Caller ID list (1 + area code + number). Some regions of the country
allow you to have more than one local area code. (Up to five local area
codes can be entered in this phone.)
1 Perform steps1to3on page13.
2 Select the number (“LOCAL 1” to “LOCAL 5”)
AREA CODE
HOME :
toenter thelocalarea codeby turning Jog Dial.
LOCAL 1:
LOCAL 2:
LOCAL 3:
3 Press Jog Button (ENTER).
“ENTER LOCAL AREA CODE 1.” appears on
the display when you select “LOCAL 1” in step
2.
4 Enter thethreedigitsofthelocalareacodeusing
thedialingkeys.
5 Press (PROGRAM).
You hearalongconfirmation beep.
Notes
•
If the local area code is already entered, it appears on the display in step 2. To
enter a different local area code, see “To change the local area code” on page
16.
•
•
Do not allow more than 20 seconds to elapse during the operation procedure.
If the local area code is not correctly entered, “SEND TO CORDLESS
HANDSET FAILED.” will appear on the display and five short error beeps
will be heard after (PROGRAM) is pressed in step 5. Move the cordless
handset closer to the base phone, and then start over the procedure.
Tips
•
When you select “[GO BACK]”, you can return to the previous set display by
pressing Jog Button (ENTER).
•
•
You may press Jog Button (ENTER) instead of (PROGRAM) in step 5.
To check the current local area code, perform steps 1 and 2. The local area
code appears on the display for about 20 seconds.
co n t in u e d
15US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 4: En t e rin g t h e a re a co d e (co n t in u e d )
To change the local area code
1 Perform steps1to3on page15.
Thecurrentlocalarea codeappearson thedisplay.
2 Press (ERASE)toerasethecurrentlocalarea code.
3 Enter a new localarea codeusing thedialing keys.
4 Press (PROGRAM).
You hearalongconfirmation beep.
To erase the local area code
You can erase the local area code. Perform steps 1 and 2 on page 15,
then press (PROGRAM). The local area code will be erased, and you
hear a long confirmation beep.
16US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 5
Se t t in g u p t h e p h o n e se rvice s
Set up the “Caller ID with call waiting”service, the Long Distance
Saver function and the voice mail service before use. Setting up the
phone services is only possible on the base phone.
To se t u p t h e “ Ca lle r ID w it h ca ll w a it in g ” se rvice
In order to use this service, you must first subscribe to “Caller ID with
call waiting” service (see page 64). The “Caller ID with call waiting”
service is preset to “ACTIVE”.
1
2
Press (PROGRAM).
(ERASE)
Turn Jog Dial to choose “BASE
SETTINGS”, and then press Jog
Button (ENTER).
3
Turn Jog Dial to choose
“PHONE SERVICES”, and then
press Jog Button (ENTER).
Jog Button
(ENTER)
PHONE SERVICES
GO BACK
(LONG DIST. SAVER)
CALL WAITING ID
VOICE MAIL
LONG DISTANCE
4
5
Press Jog Button (ENTER).
CALL WAITING ID
GO BACK
ACTIVE
INACTIVE
Turn Jog Dial to choose
“ACTIVE” or “INACTIVE”, and
then press Jog Button (ENTER).
You hear a long confirmation
beep.
co n t in u e d
17US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 5: Se t t in g u p t h e p h o n e se rvice s (co n t in u e d )
Note
Do not allow more than 20 seconds to elapse during the operation procedure.
Tip
When you select “[GO BACK]”, you can return to the previous set display by
pressing Jog Button (ENTER).
18US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
To se t u p t h e Lo n g Dist a n ce Sa ve r fu n ct io n
Many telephone companies and service providers nowadays offer low-
rate long distance calls separate from your standard long distance
provider. Such services are usually initiated by dialing an access
number prior to the long distance call itself.
The Long Distance Saver function enables you to dial the access
number of these special long distance service companies by pressing
just (LONG DIST. SAVER). After setting up the access number and
activating the button function in the menu, you only need to press
(LONG DIST. SAVER) for dialing the access number of your special long
distance carrier.
In order to use this function, you must first activate the button function
by memorizing the access number of your choice in the menu and by
setting the long distance menu function to “ACTIVE”
The long distance menu is preset to “INACTIVE”, no preset access
number is registered.
To set up the access number
1 Perform steps1and 3on page17.
2 Turn Jog Dial to choose “LONG DISTANCE”, and then
press Jog Button (ENTER).
3 Turn Jog Dial to choose “ACCESS NUMBER”, and then
press Jog Button (ENTER).
4 Enter theaccessnumber using thedialing keys.
5 Press (PROGRAM).
6 Turn Jog Dialto choose“YES” to activate
(LONG DIST. SAVER), and then press Jog Button (ENTER).
You hearalongconfirmation beep.
co n t in u e d
19US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 5: Se t t in g u p t h e p h o n e se rvice s (co n t in u e d )
Notes
•
DO NOT USE (LONG DIST. SAVER) to dial EMERGENCY services, customer
service numbers, your local telephone company, local numbers or toll
free numbers.
•
•
If you press (LONG DIST. SAVER) twice, the dialing of the registered access
number is cancelled and “[LONG DISTANCE]” disappears from the display.
If the access number is not correctly set, “SEND TO CORDLESS HANDSET
FAILED.” will appear on the display and five short error beeps will be heard
after Jog Button (ENTER) is pressed in step 6. Move the cordless handset
closer to the base phone, and then start over the procedure.
•
You can register up to 24 digits as an access number.
To change the access number
1 Perform steps1and 3on page19.
Thecurrentaccessnumber appearson thedisplay.
2 Press (ERASE)toerasethecurrentaccessnumber.
3 Enter a new accessnumber using thedialing keys.
4 Press (PROGRAM).
5 Turn Jog Dialto choose“YES” to activate
(LONG DIST. SAVER), and then press Jog Button (ENTER).
You hearalongconfirmation beep.
To activate/deactivate the Long Distance Saver function
1 Perform steps1to3on page17.
2 Turn Jog Dial to choose “LONG DISTANCE”, and then
press Jog Button (ENTER).
3 Turn Jog Dial to choose “ACTIVE” or “INACTIVE”(to
deactivate),and then pressJog Button (ENTER).
You hearalongconfirmation beep.
Notes
•
If you choose “INACTIVE” in step 3, (LONG DIST. SAVER) will be deactivated
and you cannot use (LONG DIST. SAVER) even with a registered access
number until the function is activated again.
•
Some Long Distance services may not be available in your state. Prices and
conditions may vary. For details, contact your telephone company or your
long distance provider. Some long distance call programs require a
subscription with the carrier company before usage.
•
If it is not correctly set in “ACTIVE” or “INACTIVE”, “SEND TO
CORDLESS HANDSET FAILED.” will appear on the display and five short
error beeps will be heard after Jog Button (ENTER) is pressed in step 3. Move
the cordless handset closer to the base phone, and then start over the
procedure.
20US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
To se t u p t h e vo ice m a il se rvice
In order to use this service, you must first subscribe to voice mail
service (see page 65). The voice mail service is preset to “ACTIVE”.
1 Perform steps1to3on page17.
2 Turn Jog Dial to choose “VOICE MAIL”, and then press Jog
Button (ENTER).
3 Turn Jog Dial to choose “ACTIVE” or “INACTIVE”, and
then press Jog Button (ENTER).
You hearalongconfirmation beep.
21US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 6
Se t t in g t h e d a y a n d t im e
1
2
Press (PROGRAM).
Turn Jog Dial to choose “BASE
SETTINGS”, and then press Jog
Button (ENTER).
3
Turn Jog Dialto choose
“CLOCK”, and then press Jog
Button (ENTER).
Jog Button
(ENTER)
CLOCK
GO BACK
SUNDAY
MONDAY
TUESDAY
4
Setthecorrectdayoftheweek
by turning Jog Dial,and then
press Jog Button (ENTER).
ENTER HOUR AND
PRESS JOG BUTTON
12:00AM
22US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
ENTER MINUTE AND
PRESS JOG BUTTON
5
6
7
Set thehour (1to 12)by turning Jog Dial,and
then press Jog Button (ENTER).
12:00AM
ENTER AM/PM AND
PRESS JOG BUTTON
Settheminute(00to59)by turning Jog Dial,
and then press Jog Button (ENTER).
12:00AM
Choose “AM” or “PM” by turning Jog Dial, and
then press Jog Button (ENTER).
You hear alongconfirmation beep.Then the
phonestartscountingtime.
Notes
•
•
Do not allow more than 60 seconds to elapse during the operation procedure.
“SUN 12:00AM” on the display of the base phone flashes when the day and
time is cleared due to a power interruption, or when you connect the base
phone to the AC outlet for the first time.
Tip
When you select “[GO BACK]”, you can return to the previous set display by
pressing Jog Button (ENTER).
23US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Id e n t ifyin g t h e p a rt s
Refer to the pages indicated in parentheses for details.
Base phone
qa
qs
1
2
3
4
qd
5
6
qf
qg
qh
qj
qk
ql
w;
wa
7
8
9
0
1 Display w indow (p. 31, 55)
8
TONE button (p. 32)
Allows you to switch temporarily to
tone dialing.
2 VOLUME +/– buttons
(p. 32)
Adjusts the handset or speaker
volume.
9 SPEAKERPHONE button
(p. 31)
Lets you make or receive a call.
3 NEW CALL lamp (p. 56)
Flashes when there is a “NEW”
data in the Caller ID list.
0 #button (p. 62)
Used to change the number of
digits of the phone number in the
Caller ID list.
4 Handset (p. 9, 31, 37)
5 Speaker
qa ERASE button (p. 14, 20)
qs PROGRAM button (p. 13)
qd Antenna (p. 9, 67)
6 Dialing keys (p. 31)
7 LONG DIST. SAVER button
(p. 19, 31)
Lets you make a long distance call
with the registered access number.
qf MESSAGES lamp (p. 65)
Flashes when you have messages.
qg Jog Button (ENTER) (p. 13)
24US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
wh
ws wd wf wg
qh Jog Dial (p. 13, 56)
wd DIAL MODE sw itch (p. 10)
Selects pulse or tone dialing.
qj REDIAL/PAUSE button (p. 33)
Redials one of the last five numbers
called/ inserts a pause in the dialing
sequence.
wf DC IN 11V jack (p. 9, 67)
wg LINE (telephone line) jack
(p. 9, 67)
qk INTERCOM button (p. 52)
wh HANDSET jack (p. 9)
Lets you talk between the base
phone and cordless handset.
ql CALL WAITING/FLASH button
(p. 32, 64)
Switches to a second call if you
have “call waiting” service, or lets
you make a new call.
w; HOLD button (p. 32)
Puts a call on hold.
wa MIC (microphone)
ws Hook for AC pow er adaptor
cord (p. 9, 67)
co n t in u e d
Getting Started
25US
Download from Www.Somanuals.com. All Manuals Search And Download.
Id e n t ifyin g t h e p a rt s (co n t in u e d )
Cordless handset
1
2
qd
qf
qg
3
4
5
6
7
qh
qj
qk
ql
w;
8
9
0
qa
qs
1 Antenna
0
TONE button (p. 29)
Allows you to switch temporarily to
tone dialing.
2 Speaker [EZfit] (p. 30)
3 Display w indow (p. 28, 55)
4 Jog Dial (p. 39, 56)
qa HOLD button (p. 29)
Puts a call on hold.
5 TALK button (p. 28)
qs RING sw itch (p. 36)
Lets you make or receive a call.
Switches the ringer to on/ off.
6 INTERCOM button (p. 51)
qd CALL WAITING/FLASH button
Lets you talk between the base
phone and the cordless handset.
(p. 29, 64)
Switches to a second call if you
have “call waiting” service, or lets
you make a new call.
7 LONG DIST. SAVER button
(p. 19, 29)
Lets you make a long distance call
with the registered access number.
qf REDIAL/PAUSE button
(p. 33, 41)
Redials one of the last five numbers
called/ inserts a pause in the dialing
sequence.
8 Dialing keys (p. 28)
9 Battery compartment (p. 11)
26US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
wa
ws
qg OFF button (p. 28)
Allows you to disconnect the call.
qh #button (p. 62)
Used to change the number of
digits of the phone number in the
Caller ID list.
qj PROGRAM button (p. 39)
qk ERASE button (p. 41)
ql ONE-TOUCH DIAL (A, B, C)
buttons (p. 42)
w; Microphone
wa I (HEADSET) jack (p. 28, 35, 69)
ws VOL (volume) sw itch (p. 29)
Adjust the cordless handset
volume.
27US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Ba sics
Ma kin g ca lls
1
2
Pick up thecordlesshandset
from thecharger.
(LONG DIST. SAVER)
Press (TALK)and wait until
“TALK” appears on the display
and thedisplay alsoshowsthe
talk timein hours,minutesand
seconds.
(CALL WAITING/FLASH)
The dialing keys light up.
You then hear adialtone.
I(HEADSET)
jack
VOL sw itch
“CORDLESS HANDSET IN
USE” appearson thedisplay of
thebasephone.
(*TONE)
(HOLD)
Ifyou hear fiveshort error
beeps and “OUT OF RANGE”
appearson thedisplay,move
closertothebasephone.
(ERASE)
3
4
Dialthephonenumber.
(REDIAL/PAUSE)
When you’redonetalking,press
(OFF)or replacethecordless
handseton thecharger.
Thedisplay turnsoff.
To make a call after checking the phone number
You can dial the phone number before pressing (TALK) or
(LONG DIST. SAVER). If you make a mistake when dialing the phone
number, press (ERASE) to erase the number.
28US Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
Making calls w hen the headset is connected
When a headset (optional) is connected to the I
(HEADSET) jack on the cordless handset, you can
talk through the headset.
Open
Making calls using the Long Distance Saver function
Set the menu for the Long Distance Saver function to “ACTIVE”. See
“To set up the Long Distance Saver function” on page 20.
1 Pick up thecordlesshandsetfrom thecharger.
2 Press (LONG DIST. SAVER).
“[LONG DISTANCE]” appears on the display.
To cancelthis function,press (LONGDIST. SAVER)again or
press (TALK).
3 Dialthelongdistancephonenumber(e.g.,1-201-123-4567,
or011-...).
4 When you’redonetalking,press (OFF)or replacethe
cordlesshandseton thecharger.
To make a call via Private Branch Exchange (PBX)
Before pressing (LONG DIST. SAVER) in step 2 above, enter the outside
line access digit (e.g., 9).
Additional tasks
To
Do this
Adjust the cordless
handset volume
Set the VOL switch to H (high), M (middle) or L (low).
Put a call on hold
Press (HOLD). “HOLD” appears on the display.
Press (HOLD) again or pick up the cordless handset
from the charger (When Quick talk is set to “USE”; see
page 36) to resume the conversation.
Switch to tone dialing
temporarily
Press (*TONE) after you’re connected.
The line will remain in tone dialing until disconnected.
Switch to another call
Press (CALL WAITING/FLASH).
(“call waiting” service*)
Press (CALL WAITING/FLASH) again to return to the first
caller.
* You need to subscribe to this service from your telephone company.
co n t in u e d
Basics 29US
Download from Www.Somanuals.com. All Manuals Search And Download.
Ma kin g ca lls (co n t in u e d )
Notes
•
When making a call on the cordless handset, “ ” appears on the display
indicating the receiver sensitivity with the base phone. Three bars indicate a
good reception, no bar indicates a bad reception. When calling from an area
with poor reception, you may experience interference or the call may be
disconnected, so try to use the cordless handset in areas that have a good
reception.
•
•
When you increase the sound volume, in some cases the back ground noise
may be increased as well. You should adjust the volume accordingly.
If the cordless handset beeps every second during a conversation and “ ”
appears on the display, move closer to the base phone; otherwise, you will
hear five short error beeps and “OUT OF RANGE” will appear on the
display, and the call will be disconnected after 30 seconds.
•
•
While talking with an outside caller via the base phone, you cannot make a
call with the cordless handset. If you press (TALK), “BASEPHONE IN USE”
appears on the display and you will hear a busy tone.
When the talk time exceeds 9:59:59, the display counts from 0:00:00 again.
EZfit
The “EZfit” adjusts to fit any shape ear,
thereby ensuring clear voice reception.
If the battery becomes w eak during a call
The cordless handset will beep twice per second, “BATTERY LOW”
appears on the display. Finish your call and replace the cordless
handset on the charger to charge the battery pack. Or, to continue your
phone conversation with the base phone, press (HOLD) on the cordless
handset to hold the line, and then pick up the handset or press
(SPEAKERPHONE) on the base phone.
For optimum performance, charge the battery for a full 12 hours.
Note that during the initial charge time (approx. 10 minutes), “PLEASE
WAIT...” and “BATTERY LOW” appear on the display and the
cordless handset cannot be used.
After “BATTERY LOW” turns off, you may be able to use the cordless
handset, but the battery duration will be very short; thus it is
recommended that you fully charge the battery before next use.
30US Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
Making calls w ith the base phone
(REDIAL/PAUSE)
(PROGRAM)
(CALL WAITING/ FLASH)
(VOLUME)
Pick up the handset or press
(SPEAKERPHONE) on the base phone.
“TALK” or “SPEAKERPHONE” appears
on the display and the display also shows
the talk time in hours, minutes and
seconds.
(ERASE)
(*TONE)
Dial the phone number.
Jog
When you’re done talking, replace the
handset in the cradle or press
(SPEAKERPHONE) again.
Button
(ENTER)
Jog Dial
(LONG DIST. SAVER)
(HOLD)
(SPEAKERPHONE)
To make a call after checking the phone number
You can dial the phone number before picking up the handset or
before pressing (SPEAKERPHONE). If you make a mistake when
dialing the phone number, press (ERASE) to erase the number.
Making calls using the Long Distance Saver function
Set the menu for the Long Distance Saver function to “ACTIVE”. See
“To set up the Long Distance Saver function” on page 20.
1 Pick up thehandset or press (SPEAKERPHONE)on thebase
phone.
2 Press (LONG DIST. SAVER).
“[LONG DISTANCE]” appears on the display.
To cancelthis function,press (LONGDIST.SAVER)again.
3 Dialthelongdistancephonenumber(e.g.,1-201-123-4567,
or011-...).
4 When you’redonetalking,replacethehandsetin thecradle
or press (SPEAKERPHONE)again.
To make a call via Private Branch Exchange (PBX)
Before pressing (LONG DIST. SAVER) in step 2 above, enter the outside
line access digit (e.g., 9).
co n t in u e d
Basics 31US
Download from Www.Somanuals.com. All Manuals Search And Download.
Ma kin g ca lls (co n t in u e d )
Additional tasks
To
Do this
Adjust the handset or
speakerphone volume
During phone conversation, press (VOLUME)(+)
or (-).
There are 3 steps for the handset volume level, and
7 steps for the speakerphone volume level.
Put a call on hold
Press (HOLD). “HOLD” appears on the display.
Press (HOLD), (SPEAKERPHONE), or pick up the
handset from the base phone to resume the
conversation.
Switch to tone dialing
temporarily
Press (*TONE) after you’re connected.
The line will remain in tone dialing until
disconnected.
Switch to another call
(“call waiting” service*)
Press (CALL WAITING/ FLASH).
Press (CALL WAITING/ FLASH) again to return to the
first caller.
* You need to subscribe to the service from your telephone company.
Notes
•
While talking with an outside caller via the cordless handset, the display on
the base phone shows “CORDLESS HANDSET IN USE” and you cannot
make a call with the base phone.
•
When the talk time exceeds 9:59:59, the display counts from 0:00:00 again.
Tip
You can switch between phone conversations via the handset and those via the
speakerphone, simply by picking up the handset while talking over the
speakerphone, or by pressing (SPEAKERPHONE) while talking over the handset.
To obtain the best speakerphone performance
• You may not be able to hear the other party’s voice in a noisy place.
Therefore, use the speakerphone in a quiet room.
• Do not bring your hand or other object too close to the microphone
or you will hear a shrill noise (“feedback”).
• When the speaker volume is loud, or the base phone has been placed
close to a wall, you may find that the volume drops suddenly. This
is due to a circuit in the telephone designed to protect against
feedback. In such cases, lower the speaker volume slightly.
32US Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
Re d ia lin g
Both the base phone and the cordless handset can each individually
store five dialed phone numbers.
1
2
Press (REDIAL/PAUSE).
Turn
Press
Display thenameor phone
number you want tocallby
turning Jog Dial,and then press
Jog Dial.(Ifyou’reatthebase
phone,pressJogButton
(ENTER).)
3
Turn Jog Dial to choose “DIAL”
or “LONG DISTANCE”, and
then pressJog Dial(or Jog
Button (ENTER)).
(PROGRAM)
Thephonenumber willbe
redialed.
Notes
•
•
•
•
When the Long Distance Saver function is set to “ACTIVE”, “LONG
DISTANCE” call can be made (see page 20).
The redial memory only registers up to 30 digits. Exceeding numbers will not
be redialed.
In the case of a power failure, only the redial on the base phone will be
erased.
The redial button does not store the access number of the Long Distance
Saver. To redial a long distance call, press (LONG DIST. SAVER), then
(REDIAL/PAUSE).
Tips
•
When “p” is displayed on the right end of the phone number on the redial list
in step 2, it means that some number follows the displayed phone number.
Moreover, when the phone number is selected by turning Jog Dial, all of the
phone number is displayed in two lines.
•
•
If you redial the same number repeatedly, this number will only be counted
as one number of the total five registered numbers that can be redialed.
When dialing from a phone number with a registered name, that name will
be displayed in the list in step 2.
co n t in u e d
Basics 33US
Download from Www.Somanuals.com. All Manuals Search And Download.
Ma kin g ca lls (co n t in u e d )
To store the dialed phone number into the Phone Directory
1 Display thenameor phonenumber you wanttostoreby
doing steps1and 2on page33.
2 Turn Jog Dialto choose “PROGRAM”,and then press Jog
Dial.(Ifyou’reat thebasephone,pressJog Button (ENTER).)
3 Enter thenameby doing steps4and 5on page40.
4 Turn Jog Dialto choose “[PGM]”,and then press Jog Dial(or
Jog Button (ENTER)).
You hear alongconfirmation beep,and thenameand the
numberarestored.
Note
The dialed phone numbers of up to 20 digits can be stored in the Phone
Directory.
To erase the dialed phone number one by one
1 Display thenameor phonenumber you wanttoeraseby
doing steps1and 2on page33.
2 Turn Jog Dial to choose “ERASE REDIAL”, and then press
Jog Dial.(Ifyou’reatthebasephone,pressJog Button
(ENTER).)
3 Turn Jog Dialto choose “YES”,and then press Jog Dial(or
Jog Button (ENTER)).
You hear a long confirmation beep,and thenumber is
erased.
To erase the entire dialed phone numbers at once
1 Press (PROGRAM).
2 Turn Jog Dial to choose “MEMORY MANAGE”, and then
pressJog Dial.(Ifyou’reatthebasephone,pressJog Button
(ENTER).)
3 Turn Jog Dial to choose “ERASE ALL RDL”, and then press
Jog Dial (or Jog Button (ENTER)).
4 Turn Jog Dial to choose “ERASE REDIAL”, and then press
Jog Dial (or Jog Button (ENTER)).
You hearalongconfirmation beep,and theentirenumber
areerased.
34US Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
Re ce ivin g ca lls
1
When you hear thephonering:
• Press (TALK).
or
• Pick up thecordlesshandset
from thechargerwhen the
(CALL WAITING/FLASH)
cordlesshandsetisplaced on
thecharger.(When Quick talk
isset to “USE”;seepage36)
I(HEADSET)
jack
“TALK” appears on the display
and thedisplay alsoshowsthe
talk timein hours,minutesand
seconds.
VOL sw itch
“CORDLESS HANDSET IN
USE” appearson thedisplay of
thebasephone.
(HOLD)
(PROGRAM)
2
When you’redonetalking,press
(OFF)or replacethecordless
handseton thecharger.
Thedisplay turnsoff.
Receiving calls w hen the headset is connected
When a headset (optional) is connected to the I
(HEADSET) jack on the cordless handset, you can
talk through the headset.
Open
co n t in u e d
Basics 35US
Download from Www.Somanuals.com. All Manuals Search And Download.
Re ce ivin g ca lls (co n t in u e d )
Additional tasks
To
Do this
Adjust the cordless handset
volume
Set the VOL switch to H (high), M (middle) or L
(low).
Put a call on hold
Press (HOLD). “HOLD” appears on the display.
Press (HOLD) again or pick up the cordless
handset from the charger (When Quick talk is
set to “USE”; see below) to resume the
conversation.
Switch to another call
(“call waiting” service*)
Press (CALL WAITING/FLASH).
Press (CALL WAITING/FLASH) again to return to
the first caller.
Receive a call by only picking
up the cordless handset from
the charger, without pressing
(TALK)(Quick talk)
Press (PROGRAM). Turn Jog Dial to choose
“QUICK TALK”, then press Jog Dial.
Turn Jog Dial to choose “USE”, then press Jog
Dial.
* You need to subscribe to this service from your telephone company.
Note
If there is an incoming call during intercom conversation, intercom call will be
disconnected, and both the base phone and the cordless handset will ring.
Tip
To inform you of an incoming call, the display shows “** RINGING **” even
when you set the RING switch on the cordless handset to OFF.
If you have subscribed to the Caller ID service;
•
the caller’s number and/ or name appears on the display when you receive a
call (see page 55) or when another call comes in by “call waiting” service.
•
the name stored in the one-touch dialing or Phone Directory appears on the
display if the call matches the number stored on ONE-TOUCH DIAL buttons
or in the Phone Directory (memory match function; see page 55).
•
the ringer sound changes to a higher tone if the call matches the number VIP
stored on ONE-TOUCH DIAL buttons or in the Phone Directory (memory
match function; see page 55).
To turn the ringer off
Set the RING switch on the bottom to OFF.
“[RINGER OFF]” appears on the display.
The cordless handset won’t ring. You can still make
calls, and also receive calls if another telephone
connected to the same line rings to inform you on
incoming calls. You can also receive an intercom call.
RING sw itch
36US Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiving calls w ith the base phone
When you hear the phone ring, pick up
the handset or press (SPEAKERPHONE) on
the base phone.
(CALL WAITING/ FLASH)
(VOLUME)
“TALK” or “SPEAKERPHONE” appears
on the display and the display also shows
the talk time in hours, minutes and
seconds.
When you’re done talking, replace the
handset in the cradle or press
(SPEAKERPHONE) again.
To obtain the best speakerphone
performance, see page 32.
(HOLD)
(SPEAKERPHONE)
Additional tasks
To
Do this
Adjust the handset or
speakerphone volume
During phone conversation, press (VOLUME)(+)
or (-).
There are 3 steps for the handset volume level, and
7 steps for the speakerphone volume level.
Put a call on hold
Press (HOLD). “HOLD” appears on the display.
Press (HOLD), (SPEAKERPHONE), or pick up the
handset from the base phone to resume the
conversation.
Switch to another call
(“call waiting” service*)
Press (CALL WAITING/ FLASH).
Press (CALL WAITING/ FLASH) again to return to the
first caller.
Adjust the ringer volume
of the base phone
Press (VOLUME)(+) or (-). The ringer volume can
be adjusted to three different levels: high, low, and
“OFF”. If the ringer is set to “OFF”, “[RINGER
OFF]” will appear on the display.
* You need to subscribe to the service from your telephone company.
co n t in u e d
Basics 37US
Download from Www.Somanuals.com. All Manuals Search And Download.
Re ce ivin g ca lls (co n t in u e d )
Notes
•
Even when you set “RINGER VOL” on the base phone to “OFF”, the
cordless handset will ring when the RING switch on the cordless handset is
set to ON.
•
If there is an incoming call during intercom conversation, intercom call will
be disconnected, and both the base phone and the cordless handset will ring.
Tips
•
To inform you of an incoming call, the display shows “** RINGING **”
even when you set “RINGER VOL” on the base phone to “OFF”.
•
You can switch between phone conversations via the handset and those via
the speakerphone, simply by picking up the handset while talking over the
speakerphone, or by pressing (SPEAKERPHONE) while talking over the
handset.
38US Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
Te le p h o n e Fe a t u re s
On e -t o u ch d ia lin g
You can dial with one touch of a key by storing a phone number on a
one-touch dialing button.
St o rin g p h o n e n u m b e rs a n d n a m e s
Example: to store “SONY” “123-
4567”.
1
2
Press (PROGRAM).
Turn
Press
HANDSET MENU
GO BACK
PHONE DIRECTORY
ONE-TOUCH DIAL
QUICK TALK
Turn Jog Dial to choose “ONE-
TOUCH DIAL”, and then press
Jog Dial.
(TALK)
(REDIAL/PAUSE)
ONE-TOUCH DIAL
GO BACK
(LONG DIST. SAVER)
(ERASE)
ONE-TOUCH A
ONE-TOUCH B
ONE-TOUCH C
ONE-TOUCH
DIAL buttons
3
Turn Jog Dial to choose “ONE-
TOUCH A” to “ONE-TOUCH
C”, and then press Jog Dial.
co n t in u e d
Telephone Features 39US
Download from Www.Somanuals.com. All Manuals Search And Download.
On e -t o u ch d ia lin g (co n t in u e d )
4
Enter the name by turning Jog Dial.
You can enter up to 15 characters.
ENTER NAME
SONY_
Turn Jog Dial until the desired character is
selected, and then press Jog Dial.
ABCDEFGHIJKLMNOP
QRSTUVWXYZ
SWITCH NUMBER
Each press of Jog Dial after choosing “[SWITCH]” switches the characters
from upper case letters t lower case letters t numbers and symbols.
ENTER NAME
ENTER NAME
ENTER NAME
_
_
_
ABCDEFGHIJKLMNOP
QRSTUVWXYZ
SWITCH NUMBER
abcdefghijklmnop
qrstuvwxyz
SWITCH NUMBER
0123456789"#$&'(
)*+,-./:;
SWITCH NUMBER
Enter successive characters in the same way.
To enter a “space”, turn Jog Dial to choose
“[p]”, and then press Jog Dial.
5
6
Turn Jog Dial to choose “[NUMBER]”, and then
press Jog Dial.
SONY
ENTER NUMBERS
_
“ENTER NUMBERS” appears on the display.
0123456789*#
F P VIP PGM
Enter the phone number by turning Jog Dial.
You can enter up to 20 digits, including a tone
and a pause, each of which is counted as one
digit.
SONY
1234567_
0123456789*#
F P VIP PGM
Turn Jog Dial until the desired number is
selected, and then press Jog Dial.
Icon
[F]
Meaning
SONY
Flash can be entered.
Pause can be entered.
[P]
1234567_
[VIP]
If [VIP] has been selected, “9” will appear
to the right of the displayed name. The
ring type will change when calls are
received from VIP registered numbers.
0123456789*#
F P VIP PGM
40US
Telephone Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter successive numbers in the same way.
When the phone number of 16 digits or more
has been entered, the phone number appears in
two lines.
SONY
1234567890123456
12_
0123456789*#
F P VIP PGM
7
Turn Jog Dial to choose “[PGM]”, and then
press Jog Dial.
You hear a long confirmation beep, and the
name and the number are stored.
The display goes off.
Notes
•
•
Names cannot be entered using the dialing keys.
Do not allow more than 20 seconds to elapse during the operation procedure.
Tips
•
When you select “[GO BACK]”, you can return to the previous set display by
pressing Jog Dial.
•
If you have entered a wrong name or number in step 4 or 6, turn Jog Dial to
choose “[P]” then press Jog Dial or press (ERASE) to erase it. Then enter the
correct name or number.
•
•
You may press (PROGRAM) instead of doing steps 5 and 7.
Phone numbers can be entered using the dialing keys in step 6.
To store a number to be dialed via Private Branch Exchange
(PBX)
Before entering a phone number in step 6 on page 40, do as follows:
1 Enter the outside line access digit (e.g., 9).
2 Turn Jog Dial to choose “[P]” and then press Jog Dial, or
press (REDIAL/PAUSE).
Ch a n g in g a st o re d n a m e a n d /o r p h o n e n u m b e r
1 Display the name you want to change by doing
ENTER NAME
steps 1 to 3 on page 39.
The cursor is at the right of the name.
SONY_
ABCDEFGHIJKLMNOP
QRSTUVWXYZ
SWITCH NUMBER
2 Turn Jog Dial to choose “[P]”, then press Jog
Dial to erase the characters, and enter the new
name.
If you want to change only the number, skip this
step.
co n t in u e d
Telephone Features 41US
Download from Www.Somanuals.com. All Manuals Search And Download.
On e -t o u ch d ia lin g (co n t in u e d )
3 Turn Jog Dial to choose “[NUMBER]”, and then
press Jog Dial.
SONY
The cursor is at the right of the phone number.
1234567_
0123456789*#
F P VIP PGM
4 Turn Jog Dial to choose “[P]”, then press Jog
Dial to erase the number, and enter the new
number.
If you don’t want to change the number, skip
this step.
5 Turn Jog Dial to choose “[PGM]”, and then
press Jog Dial.
You hear a long confirmation beep and the
name and/ or the number is changed.
Note
The stored record with name and number can be replaced with a new name and
number but it is not possible to erase the whole entry at one time.
Tips
•
Single character and number can be erased by pressing (ERASE) in steps 2
and 4.
•
You may press (PROGRAM) instead of doing steps 3 and 5.
Ma kin g ca lls w it h o n e -t o u ch d ia lin g
1 Press (TALK) or (LONG DIST. SAVER) and wait until “TALK”
appears on the display.
2 Press one of the ONE-TOUCH DIAL buttons ((A) to (C)).
The phone number stored on the one-touch dialing button
will appear on the display and will be dialed.
To check the phone number before one-touch dialing
While the cordless handset is not in use, press one of the ONE-TOUCH
DIAL buttons ((A) to (C)).
The number stored on the button appears on the display for 20
seconds. To dial the number, press (TALK) while the number is
displayed.
42US
Telephone Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph o n e Dire ct o ry
You can dial a number by scrolling through the Phone Directory.
Both the base phone and the cordless handset can each store up to 50
separate numbers.
St o rin g p h o n e n u m b e rs a n d n a m e s
1
Press (PROGRAM).
Turn
Press
(Cordless handset)
HANDSET MENU
GO BACK
PHONE DIRECTORY
ONE-TOUCH DIAL
QUICK TALK
If “PHONE DIRECTORY” is
not selected, turn Jog Dial to
select it.
2
3
Press Jog Dial. (If you’re at the
base phone, press Jog Button
(ENTER).)
“ENTER NAME” appears on
the display.
ENTER NAME
_
ABCDEFGHIJKLMNOP
QRSTUVWXYZ
SWITCH NUMBER
Enter the name and the phone
number by doing steps 4 to 7 on
pages 40 to 41.
Note
If you try to save a 51st phone number, you will hear five short error beeps and
“THE MEMORY IS FULL.” will be displayed. You cannot store the phone
number. To store another phone number, erase one of the stored phone
numbers (see page 45).
co n t in u e d
Telephone Features 43US
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph o n e Dire ct o ry (co n t in u e d )
Ch a n g in g a st o re d n a m e a n d /o r p h o n e
n u m b e r
1 Display the name you want to change by doing
BROWN JOHN
steps 1 to 3 on pages 46 to 47.
SONY
SMITH JOHN
SALINGER GREG
WAGNER ANTHONY
2 Press Jog Dial. (If you’re at the base phone, press
GO BACK
Jog Button (ENTER).)
DIAL
LONG DISTANCE
EDIT
ERASE DIRECTORY
3 Turn Jog Dial to choose “EDIT”, and then press
ENTER NAME
Jog Dial (or Jog Button (ENTER)).
The cursor is at the right of the name.
SONY_
ABCDEFGHIJKLMNOP
QRSTUVWXYZ
SWITCH NUMBER
4 Change the name and/ or the phone number by
doing steps 2 to 5 on pages 41 to 42.
44US
Telephone Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Era sin g a m e m o ry lo ca t io n
To erase the phone number one by one
1 Display the name you want to erase by doing
BROWN JOHN
steps 1 to 3 on pages 46 to 47.
SONY
SMITH JOHN
SALINGER GREG
WAGNER ANTHONY
2 Press Jog Dial. (If you’re at the base phone, press
GO BACK
Jog Button (ENTER).)
DIAL
LONG DISTANCE
EDIT
ERASE DIRECTORY
3 Turn Jog Dial to choose “ERASE DIRECTORY”,
and then press Jog Dial (or Jog Button
(ENTER)).
ERASE DIRECTORY
GO BACK
NO
YES
4 Turn Jog Dial to choose “YES”, and then press
Jog Dial (or Jog Button (ENTER)).
You hear a long confirmation beep and the
memory location is erased.
co n t in u e d
Telephone Features 45US
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph o n e Dire ct o ry (co n t in u e d )
To erase the entire memory at once
1 Press (PROGRAM).
2 Turn Jog Dial to choose “MEMORY
MEMORY MANAGE
GO BACK
MANAGE”, and then press Jog Dial. (If you’re
at the base phone, press Jog Button (ENTER).)
SEND ALL DIR
ERASE ALL CID
ERASE ALL RDL
3 Turn Jog Dial to choose “ERASE ALL DIR”,
ERASE ALL DIR?
GO BACK
and then press Jog Dial (or Jog Button (ENTER)).
NO
ERASE DIRECTORY
4 Turn Jog Dial to choose “ERASE DIRECTORY”,
and then press Jog Dial (or Jog Button (ENTER)).
You hear a long confirmation beep and the
entire memory is erased.
Ma kin g ca lls fro m t h e Ph o n e Dire ct o ry
Turn
Press
1
Press Jog Dial. (If you’re at the
base phone, press Jog Button
(ENTER).)
“PHONE DIRECTORY”
appears on the display.
PHONE DIRECTORY
CALLER ID
ABC
DEF
GHI
(TALK)
(LONG DIST. SAVER)
(PROGRAM)
46US
Telephone Features
Download from Www.Somanuals.com. All Manuals Search And Download.
2
3
Turn Jog Dial to select an alphabet group
([ABC], [DEF]...) which includes the initial
character of the name you want to search for,
and then press Jog Dial (or Jog Button
(ENTER)).
PHONE DIRECTORY
PQRS
TUV
WXYZ
etc
If a numbers or a symbol is the initial character,
select the “[etc]” group.
Select the name you want to call by turning Jog
Dial.
BROWN JOHN
SONY
SMITH JOHN
SALINGER GREG
WAGNER ANTHONY
4
5
Press Jog Dial (or Jog Button (ENTER)).
GO BACK
DIAL
LONG DISTANCE
EDIT
ERASE DIRECTORY
Turn Jog Dial to choose “DIAL” or “LONG
DISTANCE”, and then press Jog Dial (or Jog
Button (ENTER)).
The phone number will be dialed.
Note
When the Long Distance Saver function is set to “ACTIVE”, “LONG
DISTANCE” can be selected in step 4 (see page 20).
Tips
•
•
•
•
When you select “[GO BACK]”, you can return to the previous set display by
pressing Jog Dial. (If you’re at the base phone, press Jog Button (ENTER).)
When you select “[CALLER ID]” in step 1, you can switch to display the
Caller ID list (see page 56).
If there is no data recorded in the selected alphabet group in step 2, the data
memory of the next following group will be displayed.
You may press (TALK) or (LONG DIST. SAVER) on the cordless handset (If
you’re at the base phone, pick up the handset from the base phone or press
(SPEAKERPHONE) or (LONG DIST. SAVER)) to make a call instead of doing
steps 4 and 5.
co n t in u e d
Telephone Features 47US
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph o n e Dire ct o ry (co n t in u e d )
Tra n sfe rrin g t h e Ph o n e Dire ct o ry m e m o ry
The Phone Directory memory can be transferred one by one or all at
once (with a maximum of 50 numbers) from the cordless handset to
the base phone and from the base phone to the cordless handset.
To transfer one phone number from the Phone Directory
1 Display the name you want to transfer by doing
BROWN JOHN
steps 1 to 3 on pages 46 to 47.
SONY
SMITH JOHN
SALINGER GREG
WAGNER ANTHONY
2 Press Jog Dial. (If you’re at the base phone, press
Jog Button (ENTER).)
GO BACK
DIAL
LONG DISTANCE
EDIT
ERASE DIRECTORY
3 Turn Jog Dial to choose “SEND DIRECTORY”,
and then press Jog Dial (or Jog Button
(ENTER)).
You hear a long confirmation beep and the
memory is transferred.
To transfer all phone numbers from the Phone Directory
The Phone Directory receiving the transfer will be totally overwritten.
1 Press (PROGRAM).
2 Turn Jog Dial to choose “MEMORY
MEMORY MANAGE
GO BACK
MANAGE”, and then press Jog Dial. (If you’re
at the base phone, press Jog Button (ENTER).)
SEND ALL DIR
ERASE ALL CID
ERASE ALL RDL
48US
Telephone Features
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Press Jog Dial again (or Jog Button (ENTER)).
(Cordless handset)
SEND ALL DIR?
GO BACK
NO
SEND DIRECTORY
(BASE OVERWRITE)
4 Turn Jog Dial to choose “SEND DIRECTORY”,
and then press Jog Dial (or Jog Button
(ENTER)).
“SENDING…” appears on the display during
the transfer.
You hear a long confirmation beep and the
entire memory is transferred.
Notes
•
If there are already 50 numbers stored in the Phone Directory receiving the
transferred number one by one from the other Phone Directory, “CORDLESS
HANDSET MEMORY IS FULL.” or “BASEPHONE MEMORY IS FULL.”
will appear on the display and five short error beeps will be heard to indicate
that the transfer was unsuccessful. To make the transfer possible, erase one of
the stored phone numbers existing in the Phone Directory (see page 45).
•
If the transfer is unsuccessful, “SEND TO CORDLESS HANDSET
FAILED.” or “SEND TO BASEPHONE FAILED.” will appear on the
display, and five short error beeps will be heard. Move the cordless handset
closer to the base phone, and then start over the procedure.
Telephone Features 49US
Download from Www.Somanuals.com. All Manuals Search And Download.
Sw it ch in g t h e p h o n e s d u rin g a ca ll
You can easily switch between the cordless handset and the base
phone without disconnecting the call.
To sw it ch fro m t h e b a se p h o n e t o t h e
co rd le ss h a n d se t
1
Press (HOLD) on the base
phone.
The call is on hold and “HOLD”
appears on the display.
2
Pick up the cordless handset
from the charger (When Quick
talk is set to “USE”; see page 36)
or press (TALK) or (HOLD) on
the cordless handset.
(SPEAKERPHONE)
You can continue talking to the
caller through the cordless
handset.
To sw it ch fro m t h e co rd le ss h a n d se t t o t h e
b a se p h o n e
1
Press (HOLD) on the cordless
handset.
The call is on hold and “HOLD”
appears on the display.
2
Pick up the handset from the
base phone or press
(SPEAKERPHONE) or (HOLD)
on the base phone.
(TALK)
You can continue talking to the
caller through the base phone.
50US
Telephone Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Ta lkin g b e t w e e n t h e p h o n e s
(In t e rco m )
You can talk between the base phone and the cordless handset. You
can start the intercom from either phone.
To t a lk fro m t h e co rd le ss
h a n d se t t o t h e b a se p h o n e
Press (INTERCOM).
The base phone and cordless handset
ring and “** PAGING **” appears
on the display.
When a person at the base phone picks
up the handset from the base phone or
presses (SPEAKERPHONE) or
(INTERCOM), you can talk with each
other.
(OFF)
“INTERCOM” appears on the display.
(TALK)
When you are done talking
Replace the cordless handset on the
charger or press (OFF) on the cordless
handset.
If no one answ ers the phone
Press (INTERCOM) again.
co n t in u e d
Telephone Features 51US
Download from Www.Somanuals.com. All Manuals Search And Download.
Ta lkin g b e t w e e n t h e p h o n e s (In t e rco m ) (co n t in u e d )
To t a lk fro m t h e b a se
p h o n e t o t h e co rd le ss
h a n d se t
Press (INTERCOM).
The base phone and cordless handset
ring and “** PAGING **” appears
on the display.
When a person at the cordless handset
picks up the cordless handset from the
charger (When Quick talk is set to
“USE”; see page 36) or presses (TALK)
or (INTERCOM), you can talk with
each other.
“INTERCOM” appears on the display.
(SPEAKERPHONE)
When you are done talking
Replace the handset in the cradle or
press (SPEAKERPHONE) on the base
phone.
If no one answ ers the phone
Press (INTERCOM) again.
Notes
•
If there is an incoming call during intercom conversation, intercom call will
be disconnected, and both the base phone and the cordless handset will ring.
•
While talking with an outside caller via the base phone or cordless handset,
you cannot make an intercom call. If you press (INTERCOM) on the cordless
handset, “BASEPHONE IN USE” appears on the display and you will hear
a busy tone.
Tip
You can receive an intercom call on the base phone or the cordless handset even
when “RINGER VOL” on the base phone is set to “OFF”, or the RING switch
on the cordless handset is set to OFF. The phone will ring at a low level.
52US
Telephone Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Tra n sfe rrin g a ca ll
You can transfer a call between the cordless handset and base phone
without disconnecting the call.
To t ra n sfe r fro m t h e b a se p h o n e t o t h e
co rd le ss h a n d se t
1
Press (INTERCOM) to page the
cordless handset.
The call is put on hold on the
base phone and the cordless
handset rings.
“** PAGING **” appears on
the display of both the base
phone and cordless handset.
2
Pick up the cordless handset
from the charger (When Quick
talk is set to “USE”; see page 36)
or press (TALK) or (INTERCOM)
on the cordless handset.
(SPEAKERPHONE)
“INTERCOM” appears on the
display of both the cordless
handset and base phone.
You can talk between the base
phone and the cordless handset.
3
To talk to the caller with the
cordless handset, replace the
handset in the cradle or press
(SPEAKERPHONE) on the base
phone.
(TALK)
“TALK” appears on the display
of the cordless handset.
If no one answ ers the phone
Press (INTERCOM) again.
Tips
•
You can receive an intercom call on the cordless handset even when the
RING switch is set to OFF. The cordless handset will ring at a low level.
•
If you have accidentally pressed (HOLD) in step 1, just press (INTERCOM)
and you will get the same result as by pressing (INTERCOM) only.
co n t in u e d
Telephone Features 53US
Download from Www.Somanuals.com. All Manuals Search And Download.
Tra n sfe rrin g a ca ll (co n t in u e d )
To t ra n sfe r fro m t h e co rd le ss h a n d se t t o t h e
b a se p h o n e
1
Press (INTERCOM) to page the
base phone.
The call is put on hold on the
cordless handset and the base
phone rings. “** PAGING **”
appears on the display of both
the cordless handset and base
phone.
(OFF)
2
Pick up the handset from the
base phone or press
(SPEAKERPHONE) or
(INTERCOM) on the base phone.
“INTERCOM” appears on the
display of both the base phone
and cordless handset.
You can talk between the
cordless handset and the base
phone.
3
To talk to the caller with the
base phone, replace the cordless
handset on the charger or press
(OFF) on the cordless handset.
(INTERCOM)
“TALK” or “SPEAKERPHONE”
appears on the display of the
base phone.
(SPEAKERPHONE)
If no one answ ers the phone
Press (INTERCOM) again.
Tip
You can receive an intercom call on the base phone even when “RINGER
VOL” on the base phone is set to “OFF”. The base phone will ring at a low
level.
54US
Telephone Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Ca lle r ID Fe a t u re s
Un d e rst a n d in g t h e Ca lle r ID se rvice
Caller ID allows the caller’s phone number to be shown on the display before you
answer the call. In order to use this feature, you must first subscribe to Caller ID
service. The name of this service may vary depending on your telephone company.
To use this feature, be sure to enter the area code (see page 13).
Wh e n yo u re ce ive a ca ll
The phone number appears on the display with the date and time as shown in the
following example.
If your Caller ID service includes the caller name service or if the phone number
stored in the one-touch dialing, or the Phone Directory matches with the Caller ID
data phone number, the caller’s name also appears on the display (up to 15 letters).
The caller’s name will appear by the name stored in the one-touch dialing or Phone
Directory if you receive a call from a phone number which is stored on one of the
ONE-TOUCH DIAL buttons or in the Phone Directory.
NEW 01
Caller’s name
SMITH JOHN
Caller’s phone number
1-201-123-4567
7.04 4:53PM
The date and time received
When you answer the call, the Caller ID display changes to the “TALK” or
“SPEAKERPHONE” display.
Notes
•
-
The caller’s phone number and/ or name will not appear in the following cases:
“OUT OF AREA”: when the call is made through a telephone company which does not offer
Caller ID service (including international calls).
-
•
“PRIVATE”: when the call is “blocked”. For privacy reasons, many states allow callers the
option to prevent his or her telephone data from being displayed on the other party’s Caller
ID display.
If the call is from an office which uses multiple lines, the displayed phone number may not
match the number you use to call the extension.
About the memory match function
The name stored in the one-touch dialing or Phone Directory will appear on the
display if you receive a call from a phone number which is stored on one of the ONE-
TOUCH DIAL buttons (see page 39) or in the Phone Directory (see page 43).
In addition, the ringer sound will change to a higher tone from the second ring and
“9” will appear to the right of the displayed name if you receive a call from a VIP
registered phone number on the base phone or the cordless handset.
Note
The memory match function does not work with “OUT OF AREA” or “PRIVATE” calls; and it
may not work with calls made from an office which uses multiple lines because the number does
not always match the one you stored in this phone.
55US
Caller ID Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Lo o kin g a t t h e Ca lle r ID list
The phone stores the data of the last 100 calls received including “OUT
OF AREA” and “PRIVATE” calls. It keeps track of all calls received;
even if they were not answered.
Vie w in g t h e Ca lle r ID list
You can look through the Caller ID list on both the base phone and the
cordless handset to check the phone number and/ or name of the calls
received.
1
Turn Jog Dial.
Turn
Press
The display shows the number
of “NEW CALLS” (calls which
you have not viewed) and
“OLD CALLS” (calls which you
have viewed) calls.
CALLER ID
NEW CALLS 08
OLD CALLS 12
2
Turn Jog Dial down to display
older data or up to display
newer data.
Notes
•
•
If a 101st call is received, the oldest data is automatically erased.
When you have checked all data, “END OF LIST” appears.
NEW CALL lamp
Tip
If there is a “NEW” data, the NEW CALL lamp of
the base phone flashes.
The number of “NEW CALLS” can be confirmed
with the standby mode display of the base phone.
56US
Caller ID Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Era sin g d a t a fro m t h e Ca lle r ID list
Old data will be erased automatically when a 101st call comes in, but
you can also manually erase unnecessary data one by one or erase the
entire list.
To erase the phone number one by one
1 Display the phone number you want to erase
NEW 01
from the Caller ID list (see page 56).
SMITH JOHN
1-201-123-4567
7.04 4:53PM
2 Press Jog Dial. (If you’re at the base phone, press
GO BACK
Jog Button (ENTER).)
DIAL
LONG DISTANCE
PROGRAM
ERASE CALLER ID
3 Turn Jog Dial to choose “ERASE CALLER ID”,
and then press Jog Dial (or Jog Button
(ENTER)).
ERASE CALLER ID
GO BACK
NO
YES
4 Turn Jog Dial to choose “YES”, and then press
Jog Dial (or Jog Button (ENTER)).
You hear a long confirmation beep and the data
is erased.
Note
Do not allow more than 20 seconds to elapse during the operation procedure.
Tip
When you select “[GO BACK]”, you can return to the previous set display by
pressing Jog Dial. (If you’re at the base phone, press Jog Button (ENTER).)
co n t in u e d
57US
Caller ID Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Lo o kin g a t t h e Ca lle r ID list (co n t in u e d )
To erase the entire list at once
Entire Caller ID list deletion can only be made on the base phone.
Note that Caller ID data in the list that has not been viewed will also
be erased.
1 Press (PROGRAM).
2 Turn Jog Dial to choose “MEMORY
MEMORY MANAGE
GO BACK
MANAGE”, and then press Jog Button
(ENTER).
SEND ALL DIR
ERASE ALL CID
ERASE ALL RDL
3 Turn Jog Dial to choose “ERASE ALL CID”,
ERASE ALL CID?
GO BACK
and then press Jog Button (ENTER).
NO
ERASE CALLER ID
4 Turn Jog Dial to choose “ERASE CALLER ID”,
and then press Jog Button (ENTER).
You hear a long confirmation beep and the
entire list is erased.
Note
Do not allow more than 20 seconds to elapse during the operation procedure.
Tip
When you select “[GO BACK]”, you can return to the previous set display by
pressing Jog Button (ENTER).
58US
Caller ID Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Usin g t h e Ca lle r ID list
By using the Caller ID list, you can call back a phone number from the
Caller ID list easily, or store numbers from the Caller ID list into the
Phone Directory.
Ca llin g b a ck a n u m b e r fro m t h e Ca lle r ID list
1
2
3
Display the phone number you
want to call from the Caller ID
list (see page 56).
Turn
Press
NEW 01
SMITH JOHN
1-201-123-4567
7.04 4:53PM
(TALK)
Press Jog Dial. (If you’re at the
base phone, press Jog Button
(ENTER).)
(LONG DIST. SAVER)
GO BACK
DIAL
LONG DISTANCE
PROGRAM
ERASE CALLER ID
Turn Jog Dial to choose “DIAL”
or “LONG DISTANCE”, and
then press Jog Dial (or Jog
Button (ENTER)).
The phone automatically dials
the displayed number.
co n t in u e d
59US
Caller ID Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Usin g t h e Ca lle r ID list (co n t in u e d )
Notes
•
When the Long Distance Saver function is set to “ACTIVE”, “LONG
DISTANCE” can be selected in step 2 (see page 20).
•
If the area code is not entered, “PLEASE ENTER AREA CODE” will appear
on the display, and you will not be able to call back. Enter the area code (see
page 13).
•
•
Do not allow more than 20 seconds to elapse during the operation procedure.
If the number displayed in step 1 is not the one you should call back, you can
change the number of digits of the phone number as described on page 62.
•
If the phone is connected to a Private Branch Exchange (PBX), you may not
be able to call back from the Caller ID list because an outside line access digit
is necessary.
Tips
•
You may press (TALK) or (LONG DIST. SAVER) on the cordless handset (If
you’re at the base phone, pick up the handset from the base phone or press
(SPEAKERPHONE) or (LONG DIST. SAVER)) to make a call instead of doing
steps 2 and 3.
•
When you select “[GO BACK]”, you can return to the previous set display by
pressing Jog Dial. (If you’re at the base phone, press Jog Button (ENTER).)
60US
Caller ID Features
Download from Www.Somanuals.com. All Manuals Search And Download.
St o rin g a n u m b e r o f t h e Ca lle r ID list in t o
t h e Ph o n e Dire ct o ry
1 Display the name and phone number you want
NEW 01
to store from the Caller ID list (see page 56).
SMITH JOHN
1-201-123-4567
7.04 4:53PM
2 Confirm the number and press Jog Dial. (If
you’re at the base phone, press Jog Button
(ENTER).)
GO BACK
DIAL
LONG DISTANCE
PROGRAM
ERASE CALLER ID
3 Turn Jog Dial to choose “PROGRAM”, and then
ENTER NAME
press Jog Dial (or Jog Button (ENTER)).
The cursor is at the right of the name.
SMITH JOHN_
ABCDEFGHIJKLMNOP
QRSTUVWXYZ
SWITCH NUMBER
Enter or change the name, if necessary (see page
41).
4 Turn Jog Dial to choose “[NUMBER]”, and then
press Jog Dial (or Jog Button (ENTER)).
SMITH JOHN
The cursor is at the right of the phone number.
Enter or change the phone number, if necessary
(see page 42).
12011234567_
0123456789*#
F P VIP PGM
5 Turn Jog Dial to choose “[PGM]”, and then
press Jog Dial (or Jog Button (ENTER)).
You hear a long confirmation beep and the
name and number are stored.
co n t in u e d
61US
Caller ID Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Usin g t h e Ca lle r ID list (co n t in u e d )
Notes
•
If the area code is not entered, “PLEASE ENTER AREA CODE” will appear
on the display, and you will not be able to store into the Phone Directory.
Enter the area code (see page 13).
•
•
Do not allow more than 20 seconds to elapse during the operation procedure.
If the number displayed in step 1 is not the one you should store, you can
change the number of digits of the phone number as described below.
•
If the phone is connected to a Private Branch Exchange (PBX), you may need
to add an outside line access digit.
Tips
•
When you select “[GO BACK]”, you can return to the previous set display by
pressing Jog Dial. (If you’re at the base phone, press Jog Button (ENTER).)
•
You may press (PROGRAM) instead of doing steps 4 and 5.
To ch a n g e t h e n u m b e r o f d ig it s o f t h e p h o n e
n u m b e r
If the number of digits of the phone number in the Caller ID list is
different from the actual phone number, you need to adjust the
number of digits of the phone number to call back or store into the
Phone Directory.
1 While the phone number from the Caller ID list is displayed,
press (#) repeatedly until the phone number with the
correct number of digits appears on the display.
Each time you press (#), the number of digits changes as
follows:
When the home area code and the local area code do
not match
NEW 01
NEW 01
SMITH JOHN
SMITH JOHN
1-201-123-4567
7.04 4:53PM
201-123-4567
7.04 4:53PM
NEW 01
NEW 01
SMITH JOHN
123-4567
7.04 4:53PM
SMITH JOHN
1-123-4567
7.04 4:53PM
62US
Caller ID Features
Download from Www.Somanuals.com. All Manuals Search And Download.
When the home area code matches
NEW 01
NEW 01
SMITH JOHN
123-4567
7.04 4:53PM
SMITH JOHN
1-201-123-4567
7.04 4:53PM
NEW 01
NEW 01
SMITH JOHN
1-123-4567
7.04 4:53PM
SMITH JOHN
201-123-4567
7.04 4:53PM
When the local area code matches
NEW 01
NEW 01
SMITH JOHN
SMITH JOHN
1-123-4567
7.04 4:53PM
201-123-4567
7.04 4:53PM
NEW 01
NEW 01
SMITH JOHN
SMITH JOHN
123-4567
7.04 4:53PM
1-201-123-4567
7.04 4:53PM
2 Continue the operation to call or store the phone number
with the correct number of digits (pages 59 and 61).
Notes
•
You need to adjust the number of digits each time you call back from the
Caller ID list as the changes to the Caller ID data is not stored in memory.
•
You may not be able to change the number of digits depending on the Caller
ID data.
63US
Caller ID Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Usin g “ Ca lle r ID w it h ca ll w a it in g ”
se rvice
This telephone is compatible with the “Caller ID with call waiting”
service. Make sure that your telephone company offers this service.
Like the basic Caller ID service, you need to subscribe to “Caller ID
with call waiting” in order to use this service.
Even though you may have already subscribed to “Caller ID” and
“call w aiting” as tw o separate services, you need to request a
subscription to “Caller ID w ith call w aiting” as a single service.
This is a new service that combines the two services.
Even though you now have a “Caller ID w ith call w aiting”
compatible phone, unless you subscribe to the combined “Caller ID
w ith call w aiting” service, you w ill not be able to see the name
and number of the second caller.
When a new call comes in while you are talking, the caller’s name
and/ or phone number of the new call appears on the display for about
20 seconds.
To sw itch to another caller
1
2
To switch to the new caller,
press (CALL WAITING/FLASH).
To switch back to the first caller,
press (CALL WAITING/FLASH)
again.
Tip
When the “Caller ID with call waiting” service is set to “INACTIVE”, you
cannot use this service even if you have subscribed to “Caller ID with call
waiting” service (see page 17).
64US
Caller ID Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Usin g vo ice m a il se rvice
If you subscribe to your telephone company’s message service which
includes this feature, the display will show that you have messages
waiting to be retrieved.
MESSAGES lamp
(PROGRAM)
If yo u h a ve m e ssa g e s
“MESSAGES WAITING” appears on the
display of both the cordless handset and
base phone and the MESSAGES lamp on
the base phone flashes.
The display and the MESSAGES lamp will
go off when you retrieve your messages.
Jog
Button
(ENTER)
Jog Dial
Note
You cannot use this feature, if you have not subscribed to your telephone
company’s message service.
For details on the availability of this service, please ask your telephone
company.
Tip
When the voice mail service is set to “INACTIVE”, the MESSAGES lamp does
not function even if you have subscribed to voice mail service (see page 21).
If the MESSAGES lamp remains flashing
If this lamp does not go off (e.g. When you retrieve your messages
with other phones), you can go off the lamp manually.
To go off the MESSAGES lamp
1 Press (PROGRAM).
2 Turn Jog Dial to choose “BASE SETTINGS”,
and then press Jog Button (ENTER).
3 Turn Jog Dial to choose “MESSAGES LAMP”,
MESSAGES LAMP
GO BACK
and then press Jog Button (ENTER).
LIGHT-OFF
RESET
4 Press Jog Button (ENTER).
The MESSAGES lamp on the base phone goes
off, and you hear a long confirmation beep.
co n t in u e d
Caller ID Features
65US
Download from Www.Somanuals.com. All Manuals Search And Download.
Usin g vo ice m a il se rvice (co n t in u e d )
If you move or change your telephone company
Message waiting signals are sent in one of two ways: FSK signaling or
“stutter” signaling (Your telephone company can provide you with
more information about your service).
The first time this phone receives a voice mail message, it will set itself
to the FSK service and will lock out the stutter service if your
telephone company is in FSK service.
When you move or change your telephone company, you need to
perform the following procedure. The phone will returns to ready state
for either FSK or stutter dial tone voice mail recognition.
To reset this phone
1 Perform steps 1 and 3 on page 65.
MESSAGES LAMP
LIGHT-OFF
2 Turn Jog Dial to choose “RESET”, and then
RESET
press Jog Button (ENTER).
You hear a long confirmation beep and the
phone is reset.
66US
Caller ID Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Ad d it io n a l In fo rm a t io n
Mo u n t in g t h e b a se p h o n e o n a w a ll
1
1
2
Reverse the hang-up tab.
Hang-up tab
Plug the telephone line cord to
the LINE jack and the AC power
adaptor to the DC IN 11V jack,
and hook the cords. Use the
shorter cord for mounting.
3
Attach the wall bracket to the
center of the base phone.
2
Align the f marks of the wall
bracket with those of the base
phone.
AC pow er
adaptor cord
Telephone
line cord
4
5
Plug the telephone line cord to
the telephone outlet, and hook
the base phone to the wall plate.
Plug the AC power adaptor to
an AC outlet. Then raise the
antenna so that it points
towards the ceiling.
3
4, 5
1
2
Wall plate
Telephone
line cord
Wall bracket
AC outlet
AC pow er
adaptor
Tip
To remove the wall bracket, press the lower tabs.
Additional Information 67US
Download from Www.Somanuals.com. All Manuals Search And Download.
Ca rryin g t h e co rd le ss h a n d se t b y t h e
b e lt clip
You can hang the cordless handset on the belt by attaching the belt clip
to the cordless handset.
At t a ch in g t h e b e lt clip
Press the belt clip to the cordless
handset. Make sure that the side
tabs click and go into the holes on
the sides of the cordless handset.
Note
To prevent the cordless handset from dropping, make sure that each tab is
completely inserted.
De t a ch in g t h e b e lt clip
While pressing the back of the belt
clip, pull the sides one by one until
the tabs come off from the holes.
Note
Remove the belt clip carefully to avoid breaking your fingernails.
68US Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the headset
You can talk on the cordless handset without using your hands by
connecting a headset (optional) to the I (HEADSET) jack on the
cordless handset.
I (HEADSET)
jack
Additional Information 69US
Download from Www.Somanuals.com. All Manuals Search And Download.
No t e s o n p o w e r so u rce s
On battery pack
For the customers in the USA
• Store the battery pack at a
temperature between 41°F (5°C) and
95°F (35°C) for best performance.
RECYCLING NICKEL-CADMIUM
BATTERIES
Nickel-Cadmium batteries
are recyclable. You can help
preserve our environment
by returning your
unwanted batteries to your
nearest point for collection,
recycling or proper
• If you do not use the cordless handset
for a long period of time, remove the
battery pack after charging for more
than 12 hours.
disposal.
Note: In some areas the disposal of nickel-
cadmium batteries in household or
business trash may be prohibited.
On pow er failure
During a power interruption, you
cannot make or receive calls.
RBRC (Rechargeable Battery Recycling
Corporation) advises you about spent battery
collection by the following phone number.
Call toll free number: 1-800-822-8837
(United States and Canada only)
Caution: Do not handle damaged or leaking
nickel-cadmium batteries.
70US Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Ma in t e n a n ce
• Clean the cabinets with a soft cloth
slightly moistened with water or a
mild detergent solution. Do not use
any type of abrasive pad, scouring
powder or solvent such as alcohol or
benzine as they may damage the
finish of the cabinet.
• If the charge terminals of the charger
and cordless handset are soiled, wipe
them with a soft cloth.
If you have any questions or problems
concerning your phone, please consult
your nearest Sony dealer.
Additional Information 71US
Download from Www.Somanuals.com. All Manuals Search And Download.
Tro u b le sh o o t in g
If you’ve experienced any of the following difficulties while using your
phone, use this troubleshooting guide to help you remedy the problem.
Should any problem persist, consult your nearest Sony dealer.
Symptom
Remedy
You hear five short error
•
Make sure you have set up the base phone correctly
beeps when you press (TALK).
(page 8).
•
•
Move the cordless handset closer to the base phone.
You hear no dial tone.
Make sure the telephone line cord is securely
connected to the telephone outlet.
•
•
Make sure the battery is fully charged (page 11).
Make sure the dialing mode is set correctly (page 10).
The phone does not connect at
all, even though the number
you dial is correct.
•
•
•
•
Make sure the dialed number is really the one you
want to dial.
The phone does not redial
correctly.
During phone conversation, press (VOLUME)(+) on
the base phone to increase the speakerphone volume.
You cannot hear anything from
the speakerphone.
Make sure that the Long Distance Saver function is set
to “ACTIVE” (page 20).
(LONG DIST. SAVER) does not
function.
Make sure that the registered access number is correct
and if the service provider needs any registration
beforehand.
Even by pressing
(LONG DIST. SAVER), the long
distance call is not being made.
•
•
Set the RING switch on the cordless handset to ON.
The battery may be weak. Charge the battery for more
than 12 hours (page 11).
The cordless handset does not
ring.
•
•
Make sure you have set up the base phone correctly
(page 8).
Move the cordless handset closer to the base phone,
and confirm a dial tone is heard by pressing (TALK)
on the cordless handset.
•
•
Press (VOLUME)(+) on the base phone to increase the
ringer volume.
Make sure the telephone line cord is securely
connected to the telephone outlet.
The base phone does not ring.
72US Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
•
•
Move the cordless handset closer to the base phone.
Place the base phone away from noise sources
(page 8).
You hear interference during
conversation.
•
•
Place the base phone so that the antenna keeps away
from metal products.
This is the out-of-range alarm. Move the cordless
handset closer to the base phone within 30 seconds.
You hear a beep every second
during a conversation and “ ”
appears on the display.
•
•
The battery is weak. Charge the battery for more than
12 hours (page 11).
You hear a beep twice per
second and “BATTERY LOW”
appears on the display.
Make sure you follow the procedure for storing the
number correctly (pages 39, 43).
You hear five short error beeps
and cannot store a number on a
one-touch dial or in the Phone
Directory.
•
You have pressed a one-touch dialing button on
which no phone number has been stored.
You hear five short error beeps
when you try to make a one-
touch dial call.
•
•
Store the correct number (pages 39, 43).
One-touch dialing or Phone
Directory dialing is incorrect.
The battery may be week. Charge the battery for more
than 12 hours (page 11).
Move the cordless handset closer to the base phone.
Place the base phone away from noise sources
(page 8).
The cordless handset does not
ring when you use the intercom
from the base phone, and the
base phone does not ring when
you use the intercom from the
cordless handset.
•
•
•
The base phone is being used to converse with an
outside caller.
When pressing (INTERCOM) on
the cordless handset, you hear a
busy tone and cannot make an
intercom call.
co n t in u e d
Additional Information 73US
Download from Www.Somanuals.com. All Manuals Search And Download.
Tro u b le sh o o t in g (co n t in u e d )
Symptom
Remedy
The caller’s name and/ or
phone number does not appear
on the display.
•
•
Make sure you have subscribed to Caller ID service.
Caller ID service may not work when the phone is
connected to a Private Branch Exchange (PBX).
The call is made through company which does not
offer Caller ID service. “OUT OF AREA” will appear
on the display.
•
•
•
The call was “blocked.” “PRIVATE” will appear on
the display.
You have answered the call while “** RINGING **”
was displayed. Please answer the call after the second
ringer sound.
The caller’s name and/ or
phone number does not
appear on the display during
call waiting.
•
•
•
Make sure you have subscribed to “Caller ID with call
waiting” service (page 64).
Make sure the “Caller ID with call waiting” service is
set to “ACTIVE” (page 17).
Make sure nobody is talking with another phone on
the same telephone line.
You cannot dial the number
from the Caller ID list.
•
•
•
Make sure you entered your area code correctly
(page 13).
You may need to change the number of digits of the
phone number (page 62).
This function may not work when the phone is
connected to a Private Branch Exchange (PBX).
The memory match function
does not work.
•
•
If the call is from an office which uses multiple lines,
the phone number may not match the number you
put in the memory.
If you have stored phone number with an outside line
access digit on a one-touch dial or in the Phone
Directory because the phone is connected to a Private
Branch Exchange (PBX), the phone number will not
match the Caller ID data.
•
•
If you have stored phone number of less than 7 digits
on a one-touch dial or in the Phone Directory, the
phone number will not match the Caller ID data.
You cannot use voice mail
service.
Make sure you have subscribed to voice mail service
(page 65).
The MESSAGES lamp does not
function even if you have
subscribed to voice mail
service.
•
•
If you move or change your telephone company, reset
this phone (page 66).
Make sure that the voice mail service is set to
“ACTIVE” (page 21).
74US Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
The CHARGE lamp on the
charger does not light up when
you place the cordless handset
to charge.
• Wipe the charge terminals of the charger and the
cordless handset with a soft cloth for better contact of
the charge terminals.
• Make sure the cordless handset is placed on the
charger properly.
• Make sure the cordless handset is placed on the
charger with front side facing forward.
• Use only the supplied AC-T107 AC power adaptor.
The battery duration is short.
• The battery pack was charged less than 12 hours (due
to power failure, etc.).
• The usage life of the battery has expired and needs
replacement.
• Use only the supplied AC-T107 AC power adaptor.
Note
If any of these remedies do not work in the base phone, unplug the AC power
adaptor, and then plug it again. In the cordless handset, take the battery out,
and then insert it again.
co n t in u e d
Additional Information 75US
Download from Www.Somanuals.com. All Manuals Search And Download.
Sp e cifica t io n s
General
Base phone
Spread method
Power source
Direct-Sequence Spread-Spectrum
Access method
DC 11V from AC power adaptor
AC-T107
FDMA-TDD
Dimensions
Frequency band
Approx. 175 x 60 x 214 mm (w/ h/ d),
antenna excluded
2.406-2.475 GHz
Operating channel
23 channels
(approx. 7 x 2 3⁄8 x 8 1⁄2 inches)
Antenna: Approx. 112 mm
(approx. 4 1⁄ 2 inches)
Mass
Approx. 580 g
(approx. 1 lb 4 oz), wall bracket excluded
Dial signal
Tone, 10 PPS (pulse) selectable
Supplied accessories
See page 7.
Charger
Power source
DC 6V from AC power adaptor
Dimensions
Approx. 72.5 x 60 x 85 mm (w/ h/ d)
(approx. 2 7⁄ 8 x 2 3⁄8 x 3 3⁄8 inches)
Mass
Cordless handset
Power source
Rechargeable battery pack BP-T24
Battery life
Standby: Approx. 6 days
Talk:
Approx. 6 hours
Battery charging time
Approx. 12 hours
Dimensions
Approx. 204 g (approx. 7.2 oz)
Approx. 58 x 185.4 x 48 mm (w/ h/ d),
antenna excluded
Design and specifications are subject to
change without notice.
(approx. 2 3⁄8 x 7 3⁄8 x 1 15⁄16 inches)
Antenna: Approx. 72 mm
(approx. 2 7⁄8 inches)
Mass
Approx. 260 g
(approx. 9.2 oz), battery included
76US Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
In d e x
A
E, F, G
Erasing
Caller ID data 57
phone numbers dialed
34
R
Adjusting volume
cordless handset volume
29, 36
Receiving calls 35
Redialing 33
Ringer
handset volume 32, 37
RING switch 36
speakerphone volume
32, 37
Area code 13
Phone Directory
45
S
H
Setting up
Headset 29, 35, 69
Hold 29, 36
base phone 8
cordless handset 11
B
Battery pack
charging 11
duration 12
Home area code 13
Setting up the phone
services 17
Speakerphone 32
Storing Caller ID data in
Phone Directory 61
Switching phones during a
call 50
I, J, K
Identifying the parts 24
Intercom 51
C
Call waiting service 29, 36
Caller ID 55
Caller ID list 56
calling back 59
memory match function
55
storing in Phone
Directory 61
Caller ID with call waiting
17, 64
Carrying the cordless
handset by the belt clip 68
L
Local area code 15
Location, base phone 8
Long Distance Saver
function 19, 29
T, U
Talking between the
phones 51
Tone dialing
dialing mode 10
switching to 29
M, N
Making calls 28
Memory match function
55
Mounting the base phone
on a wall 67
Transferring a call 53
Troubleshooting 72
Connection 9
V, W, X, Y, Z
Voice mail service 65
Volume
cordless handset 29, 36
handset 32, 37
speakerphone 32, 37
D
O
Dialing mode
choosing 10
switching to the tone
temporarily 29
Directory
One-touch dialing 39
OUT OF AREA 55
P, Q
Package contents 7
Phone Directory 43
PRIVATE 55
Phone Directory 43
Pulse dialing 10
77US
Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
For the customers in the USA
Be sure to save the receipt and attach it to your WARRANTY card when having
your equipment repaired at an authorized Sony service center.
For online product registration, please contact
Sony Corporation Printed in Taiwan, R.O.C.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
