3-232-156-13 (1)
Co rd le ss
Te le p h o n e
US
Operating Instructions
Hearing-Aid Compatible
SPP-S2730
©2001 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
6. The telephone company may make
changes to it’s facilities, equipment,
operations or procedures that could
affect the operation of the equipment.
If this happens the telephone
INFORMATION FOR FCC
REGURATION CLAIM
1. This equipment complies with Part 15
and Part 68 of the FCC rules for the
United States. On the bottom of this
equipment is a label that contains,
among other information, the FCC
certification number and ringer
equivalence number (REN) for this
equipment. If requested, this
company will provide advance notice
so you can make the necessary
modifications to maintain
uninterrupted service.
7. If trouble is experienced with this
equipment (SPP-S2730), for repair or
warranty information, please contact
Sony Direct Response Center: Tel 1-
800-222-7669. If the equipment is
causing harm to the telephone
network, the telephone company may
request that you disconnect the
equipment until the problem is
resolved.
information must be provided to the
telephone company.
2. This equipment connect to
nationwide telephone network
through a modular telephone jack
which applicable certification jack
(connector) is USOC-RJ11C.
3. The FCC compliant telephone cord
and modular plug is provided with
this equipment. This equipment is
designed to be connected to the
telephone network or premises
wiring using a compatible modular
jack that is part 68 compliant.
8. All repairs will be performed in an
authorized Sony service station.
9. This equipment may not be used on
coin service provided by the Phone
Company or Party Lines.
10.This equipment is hearing aid
compatible.
4. The REN is used to determine the
quantity of devices that may be
connected to the telephone line.
Excessive RENs on the telephone line
may result in the devices not ringing
in response to an incoming call.
Typically, the sum of the RENs
should not exceed five (5.0). To be
certain of the number of devices that
may be connected to a line, as
When programming emergency
numbers and (or) making test calls to
emergency numbers:
1. Remain on the line and briefly
explain to the dispatcher the reason
for the call.
2. Perform such activities in the off-peak
hours, such as early morning or late
evenings.
determined by the total RENs, contact
the local telephone company.
5. If this equipment (SPP-S2730) causes
harm to the telephone network, the
telephone company will notify you in
advance that temporary
discontinuance of service may be
required. But if advance notice isn’t
practical, the telephone company will
notify the customer as soon as
possible. Also, you will be advised of
your right to file a complaint with the
FCC if you believe it is necessary.
3US
Download from Www.Somanuals.com. All Manuals Search And Download.
Precaución
IMPORTANTES
INSTRUCCIONES
DE SEGURIDAD
Se le advierte que cualquier cambio o
modificación no aprobado expresamente en el
presente manual podría anular su autorización
para operar este equipo.
El secreto de las comunicaciones puede no
asegurarse cuando utilice este teléfono.
A fin de reducir el riesgo de
incendio, descarga eléctrica y
lesiones a las personas cuando usted
use su equipo telefónico, siempre
debe observar precauciones básicas
de seguridad, entre ellas:
1.No use este producto cerca del
agua, por ejemplo, cerca de una
bañera, lavabo, fregadero de
cocina o lavadora, en un sótano
mojado o cerca de una piscina.
2.Evite usar un teléfono (que no sea
del tipo inalámbricos) durante una
tormenta eléctrica. Existe la
remota posibilidad de shock
eléctrico debido a rayos.
3.Para notificar una fuga de gas, no
utilice el teléfono en la vecindad
de dicha fuga.
Nota
Este equipo se ha sometido a pruebas y se ha
determinado que cumple los límites para un
aparato digital Clase B de conformidad con la
Parte 15 de las Reglas FCC. Dichos límites están
diseñados para brindar protección razonable
contra interferencia dañina en una instalación
residencial. Este equipo genera, utiliza y puede
radiar energía de radiofrecuencia y, si no se
instala y se usa de acuerdo con las instrucciones,
puede ocasionar interferencia dañina en las
radiocomunicaciones. Sin embargo, no hay
garantía de que no ocurra interferencia en una
instalación específica. En caso de que este equipo
ocasione interferencia dañina en la recepción de
radio o televisión, que se puede determinar
apagando y encendiendo el equipo, se le insta al
usuario a que trate de corregir la interferencia
mediante una o más de las siguientes medidas:
– Reorientar o reubicar la antena de recepción.
– Aumentar la separación entre el equipo y el
receptor.
– Conectar el equipo en un enchufe de un
circuito distinto al circuito al cual está
conectado el receptor.
4.Utilice solamente el cable de
alimentación y las pilas indicados
en este manual. No tire las pilas al
fuego. Podrían explotar.
– Consultar con el disstribuidor o con un
técnico experimentado de radio / televisión
para ayuda.
Compruebe los códigos locales
con respecto a las instrucciones
especiales sobre cómo deshacerse
de ellas.
La operación está sometida a las dos condiciones
siguientes: (1) Este dispositivo puede no causar
interferencia, y (2) Este dispositivo deberá
aceptar cualquier interferencia, incluyendo la
que pueda causar una operación indeseada.
NOTA IMPORTANTE
GUARDE ESTAS
INSTRUCCIONES
Para cumplir los requisitos de exposición a RF
de la FCC, siga las guías indicadas a
continuación a fin de proteger el cuerpo contra
la exposición a la energía electromagnética de
RF.
1. Evite el contacto directo con la antena de
transmisión durante la conversación
telefónica.
2. No reemplace ni modifique de ninguna
manera la antena.
4US
Download from Www.Somanuals.com. All Manuals Search And Download.
6. La compañía telefónica puede realizar
cambios en sus instalaciones, equipos,
operaciones, o procedimientos que
pueden afectar la operación del
INFORMACIÓN PARA LA
DEMANDA DE LA
REGLAMENTACIÓN DE LA FCC
equipo. Cuando suceda esto, la
1. Este equipo cumple con la Parte 15 y
la Parte 68 de las reglas de la FCC
para EE.UU. En la base de este equipo
hay una etiqueta que contiene, entre
otra información, el número de
compañía telefónica le avisará con
antelación para que pueda realizar las
modificaciones necesarias a fin de
mantener ininterrumpido el servicio.
7. Si experimenta algún problema con
este equipo (SPP-S2730), con respecto
a la reparación o a la información
sobre la garantía, póngase en contacto
con Sony Direct Response Center: Tel
1-800-222-7669 (EE. UU. solamente).
Si el equipo causa problemas en la
línea, la compañía telefónica puede
solicitarle que desconecte el equipo
hasta que se resuelva el problema.
certificado de la FCC y el número de
equivalencia de timbre de llamada
(REN) para este equipo. Cuando se
solicite, esta información deberá
ofrecerse a la compañía telefónica.
2. Este equipo se conecta a la red
telefónica nacional a través de una
toma telefónica modular cuya toma
(conector) de certificado aplicable es
USOC-RJ11C.
8. Todas las reparaciones deberá
realizarlas un centro de reparaciones
Sony.
3. Con este equipo se suministran un
cable telefónico y una clavija modular
que cumplen las normas de la FCC.
Este equipo ha sido diseñado para
conectarse a la red telefónica o la
instalación de un usuario utilizando
una toma modular compatible que
esté de acuerdo con la Parte 68.
9. Este equipo puede no utilizarse en el
servicio de pago previo
proporcionado por la compañía
telefónica o la línea compartida.
10.Este equipo es compatible con
dispositivos para ayuda a la audición.
4. El REN se utiliza para determinar la
cantidad de dispositivos que podrán
conectarse a la línea telefónica. El
exceso de REN conectados a la línea
telefónica puede resultar en que los
dispositivos no contesten a llamadas
entrantes. Normalmente, la suma de
REN no deberá ser superior a cinco
(5,0). Para enterarse del número total
de REN que puede conectarse a una
línea, póngase en contacto con la
compañía telefónica.
Cuando programe números de
emergencia y (o) realice llamadas de
prueba a los mismos:
1. Permanezca poco tiempo en la línea y
explique a la otra parte la razón de la
llamada.
2. Realice tales actividades en horas no
punta, como por la mañana temprano
o a últimas horas de la tarde.
5. Si este equipo (SPP-S2730) produce
daños en la red telefónica, la
compañía telefónica le notificará con
antelación que es posible que se
requiera la interrupción temporal del
servicio. Pero si la notificación con
antelación no es práctica, la compañía
telefónica lo notificará al cliente lo
antes posible. Además, se le notificará
el derecho a realizar una reclamación
a la FCC si usted lo considera
5US
necesario.
Download from Www.Somanuals.com. All Manuals Search And Download.
Ta b le o f co n t e n t s
Te le p h o n e Fe a t u re s
Ge t t in g St a rt e d
43 Phone Directory
8
9
Welcome
43
46
48
Storing phone numbers and
names
Making calls from the Phone
Directory
Changing a stored name
and/or phone number
Read this first
10 Step 1: Checking the package
contents
11 Step 2: Setting up the base phone
14 Step 3: Preparing the battery
pack
49
50
Erasing a memory location
16 Step 4: Choosing the dialing
Transferring the Phone
Directory memory
mode
17 Step 5: Entering the area code
21 Step 6: Setting the day and time
23 Setting up the EZ Access function
52 Switching the phones during a
call
52
Switching from the base
phone to the cordless
handset
25 Registering additional cordless
handsets
27 Changing the language of the
52
53
Switching from the cordless
handset to the base phone
Switching from the cordless
handset to another cordless
handset
display
28 Identifying the parts
Ba sics
32 Making calls
In t e rco m Op e ra t io n
54 Talking between the phones
32
35
37
Making calls with the
cordless handset
Making call with the base
phone
– Intercom
54
55
56
Talking from the cordless
handset to the base phone
Redialing
Talking from the base phone
to the cordless handset
39 Receiving calls
39
Receiving calls with the
cordless handset
Receiving calls with the base
phone
Talking between the cordless
handsets – Walkie-Talkie
function
41
6US
Table of contents
Download from Www.Somanuals.com. All Manuals Search And Download.
57 Transferring a call
Ad d it io n a l In fo rm a t io n
57
58
59
Transferring from the
cordless handset to the base
phone
71 Mounting the base phone on a
wall
72 Carrying the cordless handset by
Transferring from the base
phone to the cordless
handset
the belt clip
73 Notes on power sources
74 Maintenance
75 Troubleshooting
79 Specifications
80 Index
Transferring between the
cordless handsets
Ca lle r ID Fe a t u re s
60 Understanding the Caller ID
Back cover LIMITED WARRANTY
service
60
When you receive a call
61 Looking at the Caller ID list
61
62
Viewing the Caller ID list
Erasing data from the
Caller ID list
64 Using the Caller ID list
64
Calling back a number from
the Caller ID list
65
Storing a number of the
Caller ID list into the Phone
Directory
66
To change the number of
digits of the phone number
68 Using “Caller ID with call
waiting” service
69 Using voice mail service
69
If you have messages
7US
Table of contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Ge t t in g St a rt e d
We lco m e
Thank you for purchasing Sony QuadraStation 2.4!
The phone systems can be expanded to a total of four cordless
handsets and realizes the Intercom conversation* between a couple of
cordless handsets (Walkie-Talkie function).
* Also includes a communication between the base phone and the cordless
handset.
First, read the followings.
• The system includes a cordless handset. If you utilize the walkie-
talkie feature, it is necessary to purchase the SPP-H273 Sony cordless
handset used for the QuadraStation 2.4 exclusively.
• Be sure to register the additional cordless handset(s) to the base
phone before use. (See “Registering additional cordless handsets” on
page 25.)
• Some procedures may vary according to the number of the cordless
handset assigned to the system. The distinctions are explicitly
explained in this manual. In such a case, see the appropriate
procedure.
Other convenient features are as follows:
• Walkie-Talkie function — enables you to make an intercom
conversation between a couple of cordless handsets of the same
phone system far from the base phone (e.g. use out of doors) (page
56).
• EZ Access function — enables you to access to any set of numbers
up to 32 digits long by simple one-touch (page 23).
8US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Re a d t h is first
Before you use your phone, you must first set it up. Here’s a quick way
to set up your phone: Steps 1 to 6.
St e p 1
(p a g e 10)
First,unpackthephoneandthesuppliedaccessories.
St e p 2
(p a g e s 11 t o 13)
You need to do two things to set up the
base phone, including finding the best
location for the base phone.
St e p 3
(p a g e s 14 t o 15)
Insert the battery pack into the cordless
handset and charge it for more than 12
hours.
Base phone
St e p 4
(p a g e 16)
Choose an appropriate dialing mode.
St e p 5
(p a g e s 17 t o 20)
Enter the area code to use the Caller ID
service.
St e p 6
(p a g e s 21 t o 22)
Set the day and time to stamp day and
time for the incoming messages.
Cordless handset
Th a t ’s it !
For using the EZ Access function, follow the procedure in
“Setting up the EZ Access function” on page 23.
For using optional cordless handsets, follow the procedure
in “Registering additional cordless handsets” on page 25.
For changing the language of the display, follow the
procedure in “Changing the language of the display” on
page 27.
9US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 1
Ch e ckin g t h e p a cka g e co n t e n t s
Make sure you have received the following items in the package.
If anything is missing, contact your local Sony dealer.
Base phone
AC pow er adaptor for
Cordless handset
the base phone (AC-T46)
Charger/AC pow er
adaptor for the charger
(AC-T127)
Handset
Handset cord
Telephone
line cords (2)
Wall bracket/
stand for base
phone
Rechargeable
battery pack
(BP-T38)
10US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 2
Se t t in g u p t h e b a se p h o n e
Do the following steps:
• Choose the best location
• Connect the base phone
Ch o o se t h e b e st lo ca t io n
Where you place the base phone affects the reception quality of the
cordless handset.
Aw ay from noise sources such as a w indow
by a street w ith heavy traffic
Aw ay from television
sets and other
electronic equipment
Aw ay from heat sources, such as radiators,
airducts, and sunlight
Aw ay from a microw ave
oven
Aw ay from excessive
moisture, extremely low
temperatures, dust,
mechanical vibration, or
shock
Aw ay from a personal
computer
Ne a r a ce n t ra l lo ca t io n
a n d o n a le ve l su rfa ce
Aw ay from another
cordless telephone
CAUTION: • Should you experience intermittent loss of audio during a conversation, try
moving closer to the base or move base phone aw ay from other noise sources.
• The cordless telephone operates at a frequency that may cause interference to
nearby TVs, VCRs, and microw ave oven; the base phone should not be placed
near or on the top of a TV or VCR; and, if interference is experienced, moving
the cordless telephone farther aw ay from the TV, VCR, or microw ave oven w ill
often reduce or eliminate the interference.
co n t in u e d
11US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 2: Se t t in g u p t h e b a se p h o n e (co n t in u e d )
Co n n e ct t h e b a se p h o n e
If you want to hang the base phone on the wall, see page 71.
1
4
Hook the cord.
To an AC outlet
To DC IN 9V
3
To
HANDSET
To LINE
AC pow er adaptor
(supplied
AC-T46)
Telephone line cord
(supplied)
2 To a telephone
outlet
1
2
3
4
Connectthehandsetcordtothe
HANDSET jack and to the
handset.
To tilt the phone
If you want to tilt the phone, attach the
supplied wall bracket on the bottom of
the base phone.
Connectthetelephonelinecord
to the LINE jack and to a
telephoneoutlet.
Align the
2
f marks.
ConnecttheACpoweradaptor
to the DC IN 9V jack and to an
ACoutlet.
1
Raisetheantenna.Makesureit
pointstowardstheceiling.
12US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
• Use only the supplied AC-T46 AC power adaptor.
Do not use any other AC power adaptor.
Polarity of the plug
• Connect the AC power adaptor to a continuous power
supply.
–
• Place the base phone close to the AC outlet so that
you can unplug the AC power adaptor easily.
+
Tip
Modular
If your telephone outlet is not modular, contact your
telephone service company for assistance.
13US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 3
Pre p a rin g t h e b a t t e ry p a ck
Charge the battery pack for more than 12 hours before you start using
your cordless handset.
1
2
Slideopenthebattery
compartmentlidofthecordless
handset.
BP-T38
Connectthebatteryconnector
withcorrectpolarity(blackwire
goesonlowersideandredwire
goesonupperside).
Red
Black
Hook
3
4
Hookthecordsandinsertthe
batterypack.Thenclosethelid.
Connect the AC power adaptor
to the DC IN 9V jack of the
charger and to an AC outlet and
place the cordless handset on
thecharger .
To an AC outlet
The CHARGE lamp on the
chargerlightsupand
Front side
“HANDSET 1” appears on the
displayofthecordlesshandset
whenthecordlesshandsetis
properlyseatedonthecharge
terminalsofthecharger.Charge
thebatterypackformorethan
12 hours sothatthebatteryis
fully charged. The CHARGE
lampremainslitevenafter
chargingiscompleted.
AC-T127
To DC
IN 9V
CHARGE lamp
14US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
About the station number
When you start charging the battery, “HANDSET 1”
appears on the display of the cordless handset. This
shows the ID number for each cordless handset and base
phone of the system, called “station number.” The station
number of the base phone is set to 0 and that of the
cordless handset (supplied with the base phone) is set to
1 at the factory. The station number of the cordless
handset newly added to the system will be one of the
number 2 through 4 in the order of registration. (See
“Registering additional cordless handsets” on page 25.)
HANDSET 1
NEW
OLD
MASSAGE RING OFF
Battery duration
A fully charged battery pack lasts for about:
• Approx. 5 hours when you use the cordless handset continuously
• Approx. 6 days when the cordless handset is in standby mode.
Notes
• The battery pack will gradually discharge over a long period of time, even
when not in use.
• If you leave the battery pack in the cordless handset without charging it, the
battery pack will be completely discharged.
It may require several times of charging to recover to its full capacity.
• While charging, the battery pack warms up. This is not a malfunction.
To obtain the best performance from the battery
Do not place the cordless handset on the charger after each call. The
battery works best if the cordless handset is returned to the charger
after two or three calls. However, do not leave the cordless handset off
the charger for a long period of time as this will completely discharge
the battery pack.
When to purchase a new battery pack
If the battery lasts only a few minutes even after 12 hours of charging,
the usable life of the battery has expired and needs replacement.
Contact your local Sony authorized dealer or service center, and ask
for a Sony BP-T38 rechargeable battery pack.
Note
Battery life may vary depending on usage condition and ambient temperature.
15US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 4
Ch o o sin g t h e d ia lin g m o d e
For the telephone to work properly, select an appropriate dialing mode
(tone or pulse).
You can select the dialing mode on both the base phone and cordless
handset. The dialing mode that has been last set either with the base
phone or cordless handset is selected.
When you set the dialing mode with the cordless handset, make sure
the base phone* is not in use before you start the setting. You cannot
set the dialing mode while the system is in use.
* If the system includes additional cordless handsets, it is necessary to stop
using them before you start the setting as well.
1
2
Press (PGM). (Press
(PROGRAM) on the base phone.)
Press (*TONE).
You hear a confirmation beep.
DIAL MODE
1:TONE
2:PULSE
NEW
OLD
MASSAGE RING OFF
3
Press (1) for tone dialing or (2)
for pulse dialing.
You hear a long confirmation
beep.
If you aren't sure of your dialing system
Make a trial call with the dialing mode set to TONE.
If the call connects, leave the setting as is; otherwise, set to PULSE.
Note
Do not allow more than 60 seconds to elapse during the operation procedure.
16US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 5
En t e rin g t h e a re a co d e
When you use this phone for the first time, or move to an area that has a
different area code, you must enter the area code. Otherw ise, you cannot use
some functions of this phone and the Caller ID functions.
This is also necessary because the phone must be able to select an area code to
properly dial a call from the Caller ID list.
Depending on your region, enter the 3-digit area code as follows:
Case 1.
If 7-digit dialing (no area code) is accepted for local calls in your area, see “To enter
your home area code” below.
If you live in an area where calls from or to other local areas can also be made by 10-digit dialing
(area code + number), you can register up to 5 local area codes with this telephone to take
advantage of this system. See “To enter the local area code (For 10 digits phone number users)”
on page 19.
Case 2.
If 10-digit dialing (area code + number) is required for all local calls in your area, see
“To enter the local area code (For 10 digits phone number users)” on page 19.
Entering the area code is only possible on the cordless handset. Make sure the base
phone* is not in use before you start the setting. You cannot enter the area code while
the system is in use.
* If the system includes additional cordless handsets, it is necessary to stop using them before
you start the setting as well.
To e n t e r yo u r h o m e a re a co d e
1
2
Press (PGM).
Turn
Press
Turn Jog Dial to choose “AREA
CODE”, andthenpressJogDial.
(GO BACK)
HOME
LOCAL 1:
:
NEW
OLD
MASSAGE RING OFF
3
PressJogDialagain.
“ENTER HOME AREA
CODE”appearsonthedisplay.
ENTER
HOME AREA CODE
_
(ERASE)
NEW
OLD
MASSAGE RING OFF
co n t in u e d
Getting Started
17US
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 5: En t e rin g t h e a re a co d e (co n t in u e d )
4
5
Enterthethreedigitsofyourhomeareacode
usingthedialingkeys.
Press (PGM).
Youhearalongconfirmationbeep.
Notes
• If the home area code is already entered, it appears on the display in step 2.
To enter a different home area code, see “To change the home area code”
below.
• Do not allow more than 60 seconds to elapse during the operation procedure.
• If the area code has not been entered, calling back from the Caller ID list and
storing the Caller ID data into the Phone Directory cannot be performed.
• If the home area code is not correctly entered, “ERROR” will appear on the
display and five short error beeps will be heard after (PGM) is pressed in
step 5. Move the cordless handset closer to the base phone, make sure the
base phone* is not in use before you start the setting.
* If the system includes additional cordless handsets, it is necessary to stop
using them before you start the setting as well.
Tips
• When you select “(GO BACK)”, you can return to the previous set display by
pressing Jog Dial.
• To check the current home area code, perform steps 1 and 2. The home area
code appears on the display for about 60 seconds.
To change the home area code
1 Performsteps1to3onpage17.
Thecurrenthomeareacodeappearsonthedisplay.
2 Press (ERASE)toerasethecurrenthomeareacode.
3 Enteranewhomeareacodeusingthedialingkeys.
4 Press (PGM).
Youhearalongconfirmationbeep.
To erase the home area code
You can erase the home area code. Perform steps 1 and 2 above, then
press (PGM).
The home area code will be erased, and you hear a long confirmation
beep.
18US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
To e n t e r t h e lo ca l a re a co d e (Fo r 10 d ig it s
p h o n e n u m b e rs u se rs)
If a call matches one of the local area codes you entered, the phone
number will be registered with 10 digits in the Caller ID list (area code
+ number). If a call does not match one of the local area codes you
entered, the phone number will be registered with 11 digits in the
Caller ID list (1 + area code + number). Some regions of the country
allow you to have more than one local area code. (Up to five local area
codes can be entered in this phone.)
1 Performsteps1and2onpage17.
2 Select the number (“LOCAL 1” to “LOCAL 5”)
HOME
:
toenterthelocalareacodebyturningJogDial.
LOCAL 1:
LOCAL 2:
NEW
OLD
MASSAGE RING OFF
3 PressJogDial.
“ENTER LOCAL AREA CODE 1” appears on
the display when you select “LOCAL 1” in step
2.
4 Enterthethreedigitsofthelocalareacodeusing
thedialingkeys.
5 Press (PGM).
Youhearalongconfirmationbeep.
Notes
• If the local area code is already entered, it appears on the display in step 2.
To enter a different local area code, see “To change the local area code” on
page 20.
• Do not allow more than 60 seconds to elapse during the operation procedure.
• If the local area code is not correctly entered, “ERROR” will appear on the
display and five short error beeps will be heard after (PGM) is pressed in
step 5. Move the cordless handset closer to the base phone, make sure the
base phone* is not in use before you start the setting.
* If the system includes additional cordless handsets, it is necessary to stop
using them before you start the setting as well.
Tips
• When you select “(GO BACK)”, you can return to the previous set display by
pressing Jog Dial.
• To check the current local area code, perform steps 1 and 2. The local area
code appears on the display for about 60 seconds.
co n t in u e d
Getting Started
19US
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 5: En t e rin g t h e a re a co d e (co n t in u e d )
To change the local area code
1 Performsteps1to3onpage19.
Thecurrentlocalareacodeappearsonthedisplay.
2 Press (ERASE)toerasethecurrentlocalareacode.
3 Enteranewlocalareacodeusingthedialingkeys.
4 Press (PGM).
Youhearalongconfirmationbeep.
To erase the local area code
You can erase the local area code. Perform steps 1 and 2 avobe, then
press (PGM). The local area code will be erased, and you hear a long
confirmation beep.
20US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 6
Se t t in g t h e d a y a n d t im e
You can set the day and time only with the cordless handset. Make
sure the base phone* is not in use before you start the setting.
* If the system includes additional cordless handsets, it is necessary to stop
using them before you start the setting as well.
1
2
Press (PGM).
Turn
Press
Turn Jog Dial to choose “DAY/
TIME”, andthenpressJogDial.
(GO BACK)
SUNDAY
MONDAY
NEW
OLD
MASSAGE RING OFF
3
4
Setthecorrectdayoftheweek
byturningJogDial,andthen
pressJogDial.Thetimethathas
beenlastsetappearsonthe
display.
ENTER HOUR AND
PRESS JOG DIAL
12:00AM
NEW
OLD
MASSAGE RING OFF
Setthehour(1to12)byturning
JogDial
ENTER HOUR AND
PRESS JOG DIAL
11:
NEW
OLD
MASSAGE RING OFF
co n t in u e d
Getting Started
21US
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 6: Se t t in g t h e d a y a n d t im e (co n t in u e d )
ENTER MIMUTE AND
PRESS JOG DIAL
11:00
5
6
7
8
PressJogDial.
NEW
OLD
MASSAGE RING OFF
ENTER MINUTE AND
PRESS JOG DIAL
11:01
Settheminute(00to59)byturningJogDial.
PressJogDial.
NEW
OLD
MASSAGE RING OFF
SELECT AM/PM AND
PRESS JOG DIAL
11:01AMAM
NEW
OLD
MASSAGE RING OFF
Select“AM”or“PM”byturningJogDial, and
thenpressJogDial.
Youhearalongconfirmationbeep.Thenthe
phonestartscountingtime.
Notes
• Do not allow more than 60 seconds to elapse during the operation procedure.
• “SUN 12:00AM” on the display of the base phone flashes when the day and
time is cleared due to a power interruption, or when you connect the base
phone to the AC outlet for the first time.
• When “ERROR” appears on the display and five short error beeps are heard
after Jog Dial is pressed in step 8, move the cordless handset closer to the
base phone, make sure the base phone* is not in use before you start the
setting.
* If the system includes additional cordless handsets, it is necessary to stop
using them before you start the setting as well.
Tip
When you select “(GO BACK)”, you can return to the previous set display by
pressing Jog Dial.
22US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Se t t in g u p t h e EZ Acce ss fu n ct io n
The EZ Access function enables you to access to any set of numbers up
to 32 digits long by simple one-touch. Use for calling cards plus PIN,
voice mail, long distance provider, or any other set of frequently used
number.
After setting up the access number, you only need to press
(EZ ACCESS) for dialing the access number of your special services
e.g. long distance provider.
Also, you can set up just a phone number with the function for one-
touch dialing.
You can set up the EZ Access function on both the base phone and the
cordless handset, further more, you can assign a different access
number to each unit (base phone and cordless handset).
1
2
Press (PGM). (Press
(PROGRAM)onthebasephone.)
Press (EZ ACCESS).
EZ ACCESS
ENTER NUMBER
NEW
OLD
MASSAGE RING OFF
3
4
Entertheaccessnumberusing
thedialingkeys.
(ERASE)
Press (PGM) (or (PROGRAM)).
(REDIAL/PAUSE)
Youhearalongconfirmation
beep.
Notes
• Do not allow more than 60 seconds to elapse during the operation procedure.
• You can register up to 32 digits as an access number.
Tip
When you select “(GO BACK)”, you can return to the previous set display by
pressing Jog Dial.
co n t in u e d
23US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Se t t in g u p t h e EZ Acce ss fu n ct io n (co n t in u e d )
To use the EZ Access
–for making calls, see page 33, 35.
–for redialing, see page 37.
–for making calls from the Phone Directory, see page 47.
–for making calls from Caller ID list, see page 64.
To change the access number
1 Performsteps1and2onpage23.
Thecurrentaccessnumberappearsonthedisplay.
2 Press (ERASE)toerasethecurrentaccessnumber.
3 Enteranewaccessnumberusingthedialingkeys.
4 Press (PGM).(Press (PROGRAM)onthebasephone.)
Youhearalongconfirmationbeep.
To store a number to be dialed via Private Branch Exchange
(PBX)
Before entering a phone number in step 3 on page 23, do as follows:
1 Entertheoutsidelineaccessdigit(e.g.,9).
2 Press (REDIAL/PAUSE).
24US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Re g ist e rin g a d d it io n a l co rd le ss h a n d se t s
The phone system includes a cordless handset. You can expand the
system including a total of four cordless handsets. Be sure to register
the ID number of the additional cordless handset called “station
number” to the base phone before using the additional cordless
handset. The station number of the base phone is set to 0 and that of
the cordless handset (supplied with the base phone) is set to 1 at the
factory. The station number of the cordless handset newly added to the
system will be one of the number 2 through 4 in the order of
registration.
Before you start registering, set all the unit of the system in standby
mode and place them close to each other (within a distance of 12
inches). Then do the following procedure only on the additional
cordless handsets one bye one.
Caution
Do not register tw o or three cordless handsets at the same time.
Doing so may result in more than one cordless handsets having an
identical station number.
w ithin 12 inches
Base phone
cordless handset
1
2
Press (PGM).
Press (INTERCOM).
Youhearaconfirmationbeep.
ENTER SYSTEM ID
_
NEW
OLD
MASSAGE RING OFF
co n t in u e d
25US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Re g ist e rin g a d d it io n a l co rd le ss h a n d se t s (co n t in u e d )
3
4
Enter the 8 digits system ID by
pressing the dialing keys.
The system ID is shown on a sticker
affixed to the bottom of the base phone.
Press (PGM).
You hear a long confirmation beep and
the assigned station number is
displayed.
System ID
Notes
•
•
Do not allow more than 60 seconds to elapse during the operation procedure.
Once you add a cordless handset to the base phone system, you cannot change the
station numbers, or cancel the additional registrations.
•
When you press any button other than (PGM) to use an unregistered cordless
handset, the message “PLEASE REGISTER THIS HANDSET” will appear on the
display, and five short error beeps will be heard. You must first register the cordless
handset you want to add to the system.
•
•
If you try to register a cordless handset which you have already added to the system,
the five short error beeps will be heard and the registration will be canceled.
If the registration is unsuccessful, “ERROR” will appear on the display, and five short
error beeps will be heard after (PGM) is pressed in step 4. Move all the cordless
handsets closer to the base phone, and then start over the procedure.
To check the station number assigned to the additional
cordless handset
The station number of the cordless handset appears on
HANDSET 2
the display of the cordless handset while it is seated on
the charger. You can also utilize the supplied sticker of
the station number and attaching on the cordless
handset. (For details, see Operating Instructions of
SPP-H273.)
NEW
OLD
MASSAGE RING OFF
26US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a n g in g t h e la n g u a g e o f t h e d isp la y
You can choose English or Spanish as the display language by
following the procedure below.
You can select the display language both the base phone and the
cordless handset, further more, you can select the display language on
each unit (base phone and cordless handset).
To ch a n g e t h e la n g u a g e fro m En g lish t o Sp a n ish
1
2
Press (PGM). (Press
(PROGRAM)onthebasephone.)
Turn
Press
TurnJogDialtochoose
“ESPANOL”, and then press Jog
Dial.
(GO BACK)
NO
SI
NEW
OLD
MASSAGE RING OFF
3
TurnJogDialtochoose“SI”,
andthenpressJogDial.
Youwillhearalong
confirmationbeep.
Note
Do not allow more than 60 seconds to elapse during the operation procedure.
To ch a n g e t h e la n g u a g e fro m Sp a n ish t o En g lish
1 Press (PGM).(Press (PROGRAM)onthebase
phone.)
2 Turn Jog Dial to choose “ENGLISH”, and then
(REGRESAR)
NO
pressJogDial.
YES
NEW
3 TurnJogDialtochoose“YES”,andthenpress
OLD
MASSAGE RING OFF
JogDial.
Youwillhearalongconfirmationbeep.
27US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Id e n t ifyin g t h e p a rt s
Refer to the pages indicated in parentheses for details.
Base phone
1
9
0
qa
qs
2
3
4
qd
qf
5
qg
qh
qj
qk
ql
w;
6
7
8
1 Display w indow (p. 35, 60)
qa VOL – button (p. 35)
Adjusts the handset or speaker
volume.
2 VOICE MAIL lamp (p. 70)
Flashes when you have messages.
qs VOL + button (p. 35)
3 NEW CALL lamp (p. 61)
Adjusts the handset or speaker
volume.
Flashes when there is a “NEW”
data in the Caller ID list.
qd Jog Dial (p. 21, 61)
4 Handset (p. 12, 35, 41)
qf EZ ACCESS button (p. 23, 35)
5 Speaker
Lets you make a call with the
registered access number.
6
TONE button (p. 33)
Allows you to switch temporarily to
tone dialing.
qg REDIAL/PAUSE button (p. 37)
Redials one of the last five numbers
called/inserts a pause in the dialing
sequence.
7 Dialing keys (p. 35)
8 #button (p. 66)
qh CALL WAITING/FLASH button
Used to change the number of
digits of the phone number in the
Caller ID list.
(p. 36, 68)
Switches to a second call if you
have “call waiting” service, or lets
you make a new call.
9 ERASE button (p. 24)
0 PROGRAM button (p. 23)
28US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
wa
ws
wd wf
wg
qj INTERCOM button (p. 55)
wa Antenna (p. 12, 71)
Lets you talk between the base
phone and cordless handset.
ws Hook for AC pow er adaptor
cord (p. 12, 71)
qk HOLD button (p. 36)
wd DC IN 9V jack (p. 12, 71)
Puts a call on hold.
wf LINE (telephone line) jack
ql SPEAKERPHONE button
(p. 12, 71)
(p. 35)
wg HANDSET jack (p. 12)
Lets you make or receive a call.
w; MIC (microphone)
co n t in u e d
Getting Started
29US
Download from Www.Somanuals.com. All Manuals Search And Download.
Id e n t ifyin g t h e p a rt s (co n t in u e d )
Cordless handset
1
2
3
9
0
4
5
qa
6
qs
qd
7
8
1 Antenna
8 EZ ACCESS button (p. 23, 33)
Lets you make a call with the
registered access number.
2 Speaker
3 Display w indow (p. 32, 60)
9 Jog Dial (p. 17, 43, 61)
4 TALK button (p. 32)
0 OFF button (p. 32, 40)
Lets you make or receive a call.
Allows you to disconnect the call.
5 HOLD button (p. 33)
qa INTERCOM button (p. 54, 56)
Puts a call on hold.
Lets you talk between the base
phone and the cordless handset.
6 Battery compartment (p. 14)
7 CALL WAITING/FLASH button
qs Dialing keys (p. 32)
(p. 33, 68)
qd ERASE button (p. 18, 45)
Switches to a second call if you
have “call waiting” service, or lets
you make a new call.
30US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
qh
qj
qf
qk
ql
w;
qg
wa
qf
TONE button (p. 33)
ql PGM (program) button
(p. 17, 43)
Allows you to switch temporarily to
tone dialing.
w; REDIAL/PAUSE button
(p. 24, 37)
qg RINGER
Redials one of the last five numbers
called/inserts a pause in the dialing
sequence.
qh I (HEADSET) jack (p. 33, 39, 72)
qj VOL (volume) sw itch (p. 33)
Adjust the cordless handset
volume.
wa MIC (Microphone)
qk #button (p. 66)
Used to change the number of digits
of the phone number in the Caller
ID list.
31US
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Ba sics
Ma kin g ca lls
Ma kin g ca lls w it h t h e co rd le ss h a n d se t
1
2
Pick up the cordless handset
from the charger.
Press (TALK) and wait until
“TALK” appears on the display
and the display also shows the
talk time in hours, minutes and
seconds.
I (HEADSET)
The dialing keys light up.
You then hear a dial tone.
jack
VOL sw itch
“HANDSET 1 IN USE”
appears on the display of the
base phone when the cordless
handset with the station number
“1” is in use.
(HOLD)
(*TONE)
If you hear five short error
beeps and “NO
CONNECTION” appears on the
display, move closer to the base
phone.
(ERASE)
(EZ ACCESS)
(CALL WAITING/FLASH)
3
4
Dial the phone number.
When you’re done talking, press
(OFF) or replace the cordless
handset on the charger.
The display turns off.
To make a call after checking the phone number
You can dial the phone number before pressing (TALK) or
(EZ ACCESS). If you make a mistake when dialing the phone number,
press (ERASE) to erase the number.
32US Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
Making calls w hen the headset is connected
When a headset (optional) is connected to the I
(HEADSET) jack on the cordless handset, you can
talk through the headset.
Open
Making calls using the EZ Access function
To set up the access number, see “Setting up the EZ
Access function” on page 23.
1 Pick up the cordless handset from the charger.
2 Dial the phone number (e.g.,
1-201-123-4567, or 011-...).
3 Press (EZ ACCESS).
The system dials first, the access number set up
with the EZ access function, and then the phone
number you dialed in step 2. “TALK” appears
on the display.
TALK
E12011234567
NEW
OLD
MASSAGE RING OFF
4 When you’re done talking, press (OFF) or
replace the cordless handset on the charger.
Note
If you have set up a phone number with the EZ access function, just press
(EZ ACCESS) to dial the phone number (i.e. skip step 2).
Additional tasks
To
Do this
Adjust the cordless
handset volume
Set the VOL switch to H (high), M (middle) or L (low).
Put a call on hold
Press (HOLD). “HOLD” appears on the display.
Press (HOLD) again or pick up the cordless handset
from the charger (When Quick talk is set to “ON”; see
page 40) to resume the conversation.
Switch to tone dialing
temporarily
Press (*TONE) after you’re connected.
The line will remain in tone dialing until disconnected.
Switch to another call
Press (CALL WAITING/FLASH).
(“call waiting” service*)
Press (CALL WAITING/FLASH) again to return to the first
caller.
* You need to subscribe to this service from your telephone company.
co n t in u e d
Basics 33US
Download from Www.Somanuals.com. All Manuals Search And Download.
Ma kin g ca lls (co n t in u e d )
Notes
•
When making a call on the cordless handset, “ ” appears on the display
indicating the receiver sensitivity with the base phone. Three bars indicate a
good reception, no bar indicates a bad reception. When calling from an area
with poor reception, you may experience interference or the call may be
disconnected, so try to use the cordless handset in areas that have a good
reception.
•
•
When you increase the sound volume, in some cases the back ground noise
may be increased as well. You should adjust the volume accordingly.
If the cordless handset beeps every second during a conversation and “ ”
appears on the display, move closer to the base phone; otherwise, you will
hear five short error beeps and “NO CONNECTION” will appear on the
display, and the call will be disconnected after 30 seconds.
•
•
While talking with an outside caller via the base phone, you cannot make a
call with the cordless handset. If you press (TALK), “NO CONNECTION”
appears on the display and you will hear five short error beeps.
When the talk time exceeds 9:59:59, the display counts from 0:00:00 again.
If the battery becomes w eak during a call
The cordless handset will beep twice per second, “BATTERY LOW”
appears on the display. Finish your call and replace the cordless
handset on the charger to charge the battery pack.
For optimum performance, charge the battery for a full 12 hours.
Note that during the initial charge time (approx. 10 minutes), “PLEASE
WAIT...” and “BATTERY LOW” appear on the display and the
cordless handset cannot be used.
After “BATTERY LOW” turns off, you may be able to use the cordless
handset, but the battery duration will be very short; thus it is
recommended that you fully charge the battery before next use.
34US Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
Ma kin g ca lls w it h t h e b a se p h o n e
(REDIAL/PAUSE)
(PROGRAM)
(VOL +)
1 Pick up the handset or press
Jog Dial
(CALL WAITING/ FLASH)
(SPEAKERPHONE) on the base
phone.
(VOL -)
“TALK” or “SPEAKERPHONE”
appears on the display and the
display also shows the talk time in
hours, minutes and seconds.
(ERASE)
2 Dial the phone number.
3 When you’re done talking, replace
the handset in the cradle or press
(SPEAKERPHONE) again.
(EZ ACCESS)
(*TONE)
(HOLD)
(SPEAKERPHONE)
To make a call after checking the phone number
You can dial the phone number before picking up the handset or
before pressing (SPEAKERPHONE). If you make a mistake when
dialing the phone number, press (ERASE) to erase the number.
Making calls using the EZ Access function
To set up the access number, see “Setting up the EZ
Access function” on page 23.
1 Dial the phone number (e.g.,
1-201-123-4567, or 011-...).
2 Press (EZ ACCESS).
The system dials first, the access number set up
with the EZ access function, and then the phone
number you dialed in step 1.
SPEAKERPHONE
E12011234567
NEW
OLD
MASSAGE RING OFF
“SPEAKERPHONE” appears on the display.
3 When you’re done talking, or press
(SPEAKERPHONE) again.
Note
If you have set up a phone number with the EZ access function, just press
(EZ ACCESS) to dial the phone number (i.e. skip step 1).
co n t in u e d
Basics 35US
Download from Www.Somanuals.com. All Manuals Search And Download.
Ma kin g ca lls (co n t in u e d )
Additional tasks
To
Do this
Adjust the handset or
speakerphone volume
During phone conversation, press (VOL -) or
(VOL +).
There are 3 steps for the handset volume level, and
7 steps for the speakerphone volume level.
Put a call on hold
Press (HOLD). “HOLD” appears on the display.
Press (HOLD), (SPEAKERPHONE), or pick up the
handset from the base phone to resume the
conversation.
Switch to tone dialing
temporarily
Press (*TONE) after you’re connected.
The line will remain in tone dialing until
disconnected.
Switch to another call
(“call waiting” service*)
Press (CALL WAITING/ FLASH).
Press (CALL WAITING/ FLASH) again to return to the
first caller.
* You need to subscribe to the service from your telephone company.
Notes
•
While talking with an outside caller via the cordless handset, the display on
the base phone shows “HANDSET 1 IN USE” when the cordless handset
with the station number “1” is in use, and you cannot make a call with the
base phone.
•
When the talk time exceeds 9:59:59, the display counts from 0:00:00 again.
Tip
You can switch between phone conversations via the handset and those via the
speakerphone, simply by picking up the handset while talking over the
speakerphone, or by pressing (SPEAKERPHONE) while talking over the handset.
To obtain the best speakerphone performance
• You may not be able to hear the other party’s voice in a noisy place.
Therefore, use the speakerphone in a quiet room.
• Do not bring your hand or other object too close to the microphone
or you will hear a shrill noise (“feedback”).
• When the speaker volume is loud, or the base phone has been placed
close to a wall, you may find that the volume drops suddenly. This
is due to a circuit in the telephone designed to protect against
feedback. In such cases, lower the speaker volume slightly.
36US Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
Re d ia lin g
Both the base phone and the cordless handset can each individually
store five dialed phone numbers.
1
2
Press (REDIAL/PAUSE).
Turn
Press
Display the name or phone
number you want to call by
turning Jog Dial.
3
4
Press Jog Dial.
Turn Jog Dial to choose “DIAL”,
and then press Jog Dial.
The phone number will be
redialed.
(PGM)
(EZ ACCESS)
Notes
•
The redial memory only registers up to 32 digits. Exceeding numbers will not
be redialed.
•
If an access number of the long distance call is registered in (EZ ACCESS), the
number cannot be stored for the redial button use. To redial long distance
calls with (EZ ACCESS), press (EZ ACCESS) instead of above steps 3 and 4.
Tips
•
•
•
Although the phone number displayed on the redial list is up to 15 digit, the
redialing will be successful.
If you redial the same number repeatedly, this number will only be counted
as one number of the total five registered numbers that can be redialed.
When dialing from a phone number with a registered name, that name will
be displayed in the list in step 2.
co n t in u e d
Basics 37US
Download from Www.Somanuals.com. All Manuals Search And Download.
Ma kin g ca lls (co n t in u e d )
To erase the dialed phone number one by one
1 Display the name or phone number you want to erase by
doing steps 1 to 3 on page 37.
2 Turn Jog Dial to choose “ERASE REDIAL”, and then press
Jog Dial.
3 Turn Jog Dial to choose “YES”, and then press Jog Dial.
You hear a long confirmation beep, and the number is
erased.
To erase the entire dialed phone numbers at once
1 Press (PGM). (Press (PROGRAM) on the base phone.)
2 Turn Jog Dial to choose “MEMORY MANAGE”, and then
press Jog Dial.
3 Turn Jog Dial to choose “ERASE ALL RDL”, and then press
Jog Dial.
4 Turn Jog Dial to choose “ERASE REDIAL”, and then press
Jog Dial.
You hear a long confirmation beep, and the entire number
are erased.
To store the dialed phone number into the Phone Directory
See page 45.
38US Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
Re ce ivin g ca lls
Re ce ivin g ca lls w it h t h e co rd le ss h a n d se t
1
When you hear the phone ring:
• Press (TALK).
or
• Pick up the cordless handset
from the charger when the
cordless handset is placed on
the charger. (When Quick talk
is set to “ON”; see page 40)
I (HEADSET)
jack
VOL sw itch
(HOLD)
“TALK” appears on the display
and the display also shows the
talk time in hours, minutes and
seconds.
“HANDSET 1 IN USE”
appears on the display of the
base phone when the cordless
handset with the station number
“1” is in use.
(CALL WAITING/FLASH)
(PGM)
2
When you’re done talking, press
(OFF) or replace the cordless
handset on the charger.
The display turns off.
Receiving calls w hen the headset is connected
When a headset (optional) is connected to the I
(HEADSET) jack on the cordless handset, you can
talk through the headset.
Open
co n t in u e d
Basics 39US
Download from Www.Somanuals.com. All Manuals Search And Download.
Re ce ivin g ca lls (co n t in u e d )
Additional tasks
To
Do this
Adjust the cordless handset
volume
Set the VOL switch to H (high), M (middle) or L
(low).
Put a call on hold
Press (HOLD). “HOLD” appears on the display.
Press (HOLD) again or pick up the cordless
handset from the charger (When Quick talk is
set to “ON”; see below) to resume the
conversation.
Switch to another call
(“call waiting” service*)
Press (CALL WAITING/FLASH).
Press (CALL WAITING/FLASH) again to return to
the first caller.
Receive a call by only picking
up the cordless handset from
the charger, without pressing
(TALK)(Quick talk)
Press (PGM). Turn Jog Dial to choose “QUICK
TALK”, then press Jog Dial.
Turn Jog Dial to choose “ON”, then press Jog
Dial.
Adjust the ringer volume of
the cordless handset
While the cordless handset is ringing: Turn Jog
Dial to adjust the volume.
While the cordless handset is not in use: Press
(PGM). Turn Jog Dial to choose “RINGER
VOLUME” then press Jog Dial to adjust the
volume. Press (OFF).
The ringer volume can be adjusted to three
different levels: high, low and off. If the ringer
is set off, “RING OFF” will appear on the
display.
* You need to subscribe to this service from your telephone company.
Tip
To inform you of an incoming call, the display shows “** RINGING **” even
when you set the ringer volume on the cordless handset to off. You can still
make calls, and also receive calls if another telephone connected to the same
line rings to inform you of incoming calls. You can also receive an intercom call.
If you have subscribed to the Caller ID service;
•
the caller’s number and/ or name appears on the display when you receive a
call (see page 60) or when another call comes in by “call waiting” service.
•
the name stored in the Phone Directory appears on the display if the call
matches the number stored in the Phone Directory (memory match function;
see page 60).
•
the ringer sound changes to a higher tone if the call matches the number
stored in the Phone Directory (memory match function; see page 60).
40US Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
Re ce ivin g ca lls w it h t h e b a se p h o n e
(CALL WAITING/ FLASH) (VOL +)
1 When you hear the phone ring,
pick up the handset or press
(SPEAKERPHONE) on the base
phone.
(VOL -)
“TALK” or “SPEAKERPHONE”
appears on the display and the
display also shows the talk time in
hours, minutes and seconds.
2 When you’re done talking, replace
the handset in the cradle or press
(SPEAKERPHONE) again.
(HOLD)
(SPEAKERPHONE)
To obtain the best speakerphone
performance, see page 36.
Additional tasks
To
Do this
Adjust the handset or
speakerphone volume
During phone conversation, press (VOL +) or
(VOL -).
There are 3 steps for the handset volume level, and
7 steps for the speakerphone volume level.
Put a call on hold
Press (HOLD). “HOLD” appears on the display.
Press (HOLD), (SPEAKERPHONE), or pick up the
handset from the base phone to resume the
conversation.
Switch to another call
(“call waiting” service*)
Press (CALL WAITING/ FLASH).
Press (CALL WAITING/ FLASH) again to return to the
first caller.
Adjust the ringer volume
of the base phone
Press (VOL +) or (VOL -). The ringer volume can
be adjusted to three different levels: high, low, and
off. If the ringer is set to off, “RING OFF” will
appear on the display.
* You need to subscribe to the service from your telephone company.
co n t in u e d
Basics 41US
Download from Www.Somanuals.com. All Manuals Search And Download.
Re ce ivin g ca lls (co n t in u e d )
Note
Even when you set the ringer volume on the base phone to off, the cordless
handset will ring when the ringer volume on the cordless handset is set to high
or low.
Tips
•
To inform you of an incoming call, the display shows “** RINGING **”
even when you set the ringer volume on the base phone to off.
•
You can switch between phone conversations via the handset and those via
the speakerphone, simply by picking up the handset while talking over the
speakerphone, or by pressing (SPEAKERPHONE) while talking over the
handset.
42US Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
Te le p h o n e Fe a t u re s
Ph o n e Dire ct o ry
You can dial a number by scrolling through the Phone Directory.
Both the base phone and the cordless handset can each store up to 50
separate numbers.
St o rin g p h o n e n u m b e rs a n d n a m e s
Example: to store “SONY” “123-
4567”.
1
Press (PGM). (Press
(PROGRAM) on the base phone.)
Turn
Press
(GO BACK)
PHONE DIRECTORY
MEMORY MANAGE
OLD
NEW
MASSAGE RING OFF
If “PHONE DIRECTORY” is
not selected, turn Jog Dial to
select it.
2
3
Press Jog Dial.
“ENTER NAME” appears on
the display.
(ERASE)
ENTER NAME
ABCDEFGHIJKLMN
OPQRSTUVWXYZ
NEW
OLD
MASSAGE RING OFF
(REDIAL/PAUSE)
Enter the name by turning Jog
Dial.
You can enter up to 15
characters.
Turn Jog Dial until the desired
character is selected, and then
press Jog Dial.
co n t in u e d
Telephone Features 43US
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph o n e Dire ct o ry (co n t in u e d )
Each press of Jog Dial after choosing “M” or
“m” switches the characters from upper case
letters t lower case letters t numbers and
symbols.
ENTER NAME
ABCDEFGHIJKLMN
OPQRSTUVWXYZ
MASSAGE RING OFF
NEW
OLD
ENTER NAME
abcdefghijklmn
opqrstuvwxyz
MASSAGE RING OFF
NEW
OLD
Enter successive characters in the same way.
To enter a “space”, turn Jog Dial to choose
“ ” (space), and then press Jog Dial.
ENTER NAME
0123456789"#$&
'()*+,-./:;
MASSAGE RING OFF
NEW
OLD
4
5
Press (PGM) (or (PROGRAM)).
SONY
ENTER NUMBER
“ENTER NUMBER” appears on the display.
NEW
OLD
MASSAGE RING OFF
Enter the phone number by pressing the dialing
keys.
SONY
1234567_
NEW
OLD
MASSAGE RING OFF
You can enter up to 20 digits, including a tone
and a pause, each of which is counted as one
digit.
SONY
1234567890123456
78_
NEW
When the phone number of 16 digits or more
has been entered, the phone number appears in
two lines.
OLD
MASSAGE RING OFF
6
Press (PGM) (or (PROGRAM)).
You hear a long confirmation beep, and the
name and the number are stored.
The display goes off.
44US
Telephone Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
•
If you try to save a 51st phone number, you will hear five short error beeps
and “THE MEMORY IS FULL” will be displayed. You cannot store the
phone number. To store another phone number, erase one of the stored
phone numbers (see page 49).
•
•
Names cannot be entered using the dialing keys.
Do not allow more than 60 seconds to elapse during the operation procedure.
Tips
•
When you select “(GO BACK)”, you can return to the previous set display by
pressing Jog Dial.
•
If you have entered a wrong name or number in step 3 or 5, turn Jog Dial to
choose “P” then press Jog Dial or press (ERASE) to erase it. Then enter the
correct name or number.
To store a number to be dialed via Private Branch Exchange
(PBX)
Before entering a phone number in step 5 on page 44, do as follows:
1 Enter the outside line access digit (e.g., 9).
2 Press (REDIAL/PAUSE).
To store the dialed phone number into the Phone Directory
The dialed phone numbers of up to 20 digits can be stored in the
Phone Directory.
1 Press (REDIAL/PAUSE).
2 Display the name or phone number you want to call by
turning Jog Dial, and then press Jog Dial.
3 Turn Jog Dial to choose “PROGRAM”, and then press Jog
Dial.
4 Enter the name by doing steps 3 and 4 on pages 43 to 44.
5 Press (PGM). (Press (PROGRAM) on the base phone.)
You hear a long confirmation beep, and the name and the
number are stored.
co n t in u e d
Telephone Features 45US
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph o n e Dire ct o ry (co n t in u e d )
Ma kin g ca lls fro m t h e Ph o n e Dire ct o ry
Turn
Press
1
Press Jog Dial.
“PHONE DIRECTORY”
appears on the display.
PHONE DIRECTORY
ABC
DEF
NEW
OLD
MASSAGE RING OFF
(TALK)
(PGM)
(EZ ACCESS)
2
Turn Jog Dial to select an alphabet group
([ABC], [DEF]...) which includes the initial
character of the name you want to search for,
and then press Jog Dial.
TUV
WXYZ
etc
NEW
OLD
MASSAGE RING OFF
If a numbers or a symbol is the initial character,
select the “[etc]” group.
BROWN JOHN
SONY
SMITH JOHN
3
4
Select the name you want to call by turning Jog
Dial.
NEW
OLD
MASSAGE RING OFF
Press Jog Dial.
(GO BACK)
DIAL
EDIT
NEW
OLD
MASSAGE RING OFF
46US
Telephone Features
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Turn Jog Dial to choose “DIAL”, and then press
Jog Dial.
The phone number will be dialed.
Tips
•
•
•
When you select “(GO BACK)”, you can return to the previous set display by
pressing Jog Dial.
If there is no data recorded in the selected alphabet group in step 2, the data
memory of the next following group will be displayed.
You may press (TALK) on the cordless handset (on the base phone, pick up
the handset or press (SPEAKERPHONE)) to make a call instead of doing steps
4 and 5.
•
If an access number of the long distance call is set up with the EZ access
function, you can add the access number to the phone number and make a
call by pressing (EZ ACCESS) after step 3. For setting up the EZ access
function, see page 23.
co n t in u e d
Telephone Features 47US
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph o n e Dire ct o ry (co n t in u e d )
Ch a n g in g a st o re d n a m e a n d /o r p h o n e
n u m b e r
1 Display the name you want to change by doing
BROWN JOHN
SONY
SMITH JOHN
steps 1 to 3 on page 46.
NEW
OLD
MASSAGE RING OFF
2 Press Jog Dial.
(GO BACK)
DIAL
EDIT
NEW
OLD
MASSAGE RING OFF
3 Turn Jog Dial to choose “EDIT”, and then press
SONY_
ABCDEFGHIJKLMN
OPQRSTUVWXYZ
Jog Dial.
The cursor “_” is at the right of the name.
NEW
OLD
MASSAGE RING OFF
4 Turn Jog Dial to choose “P”, then press Jog Dial
or press (ERASE) to erase the characters, and
enter the new name.
If you want to change only the number, skip this
step.
SONY
1234567_
5 Press (PGM). (Press (PROGRAM) on the base
phone.)
NEW
OLD
MASSAGE RING OFF
The cursor is at the right of the phone number.
6 Press (ERASE) to erase the number, and enter
the new number.
If you don’t want to change the number, skip
this step.
7 Press (PGM) (or (PROGRAM)).
You hear a long confirmation beep and the
name and/ or the number is changed.
48US
Telephone Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Era sin g a m e m o ry lo ca t io n
To erase the phone number one by one
1 Display the name you want to erase by doing
BROWN JOHN
SONY
SMITH JOHN
steps 1 to 3 on page 46.
NEW
OLD
MASSAGE RING OFF
2 Press Jog Dial.
(GO BACK)
DIAL
EDIT
NEW
OLD
MASSAGE RING OFF
3 Turn Jog Dial to choose “ERASE DIRECTORY”,
(GO BACK)
NO
and then press Jog Dial.
YES
NEW
OLD
MASSAGE RING OFF
4 Turn Jog Dial to choose “YES”, and then press
Jog Dial.
You hear a long confirmation beep and the
memory location is erased.
To erase the entire memory at once
1 Press (PGM). (Press (PROGRAM) on the base
phone.)
2 Turn Jog Dial to choose “MEMORY
(GO BACK)
PHONE DIRECTORY
MANAGE”, and then press Jog Dial.
MEMORY MANAGE
OLD
NEW
MASSAGE RING OFF
3 Turn Jog Dial to choose “ERASE ALL DIR”,
(GO BACK)
NO
ERASE DIRECTORY
and then press Jog Dial.
NEW
OLD
MASSAGE RING OFF
4 Turn Jog Dial to choose “ERASE DIRECTORY”,
and then press Jog Dial.
You hear a long confirmation beep and the
entire memory is erased.
co n t in u e d
Telephone Features 49US
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph o n e Dire ct o ry (co n t in u e d )
Tra n sfe rrin g t h e Ph o n e Dire ct o ry m e m o ry
The Phone Directory memory can be transferred one by one or all at
once (with a maximum of 50 numbers) from a cordless handset to the
base phone or to an additional cordless handset, or from a base phone
to one of the cordless handsets.
Make sure the base phone* is not in use before you start the setting.
* If the system includes additional cordless handsets, it is necessary to stop
using them before you start the setting as well.
To transfer one phone number from the Phone Directory
1 Display the name you want to transfer by doing
BROWN JOHN
SONY
SMITH JOHN
steps 1 to 3 on page 46.
NEW
OLD
MASSAGE RING OFF
2 Press Jog Dial.
(GO BACK)
DIAL
EDIT
NEW
OLD
MASSAGE RING OFF
3 Turn Jog Dial to choose “SEND DIRECTORY”,
and then press Jog Dial.
4 When the system has one cordless handset
You hear a long confirmation beep and the
memory is transferred.
When the system has an additional cordless
handset
(Cordless handset)
(GO BACK)
TO BASE
TO HANDSET 2
Turn Jog Dial to choose “TO BASE” or station
number of the cordless handset to which you
are forwarding the memory, and then press Jog
Dial.
NEW
OLD
MASSAGE RING OFF
You hear a long confirmation beep and the
memory is transferred.
50US
Telephone Features
Download from Www.Somanuals.com. All Manuals Search And Download.
To transfer all phone numbers from the Phone Directory
The Phone Directory receiving the transfer will be totally overwritten.
1 Press (PGM). (Press (PROGRAM) on the base
phone.)
2 Turn Jog Dial to choose “MEMORY
(GO BACK)
SEND ALL DIR
ERASE ALL CID
MANAGE”, and then press Jog Dial.
NEW
OLD
MASSAGE RING OFF
3 Press Jog Dial.
4 When the system has one cordless handset
Skip this step.
(Cordless handset)
When the system has an additional cordless
handset
(GO BACK)
TO BASE
TO HANDSET 2
Turn Jog Dial to choose “TO BASE” or station
number of the cordless handset to which you
are forwarding the memory, and then press Jog
Dial.
NEW
OLD
MASSAGE RING OFF
5 Turn Jog Dial to choose “SEND DIRECTORY”,
(GO BACK)
NO
SEND DIRECTORY
and then press Jog Dial.
“SENDING…” appears on the display during
the transfer.
NEW
OLD
MASSAGE RING OFF
You hear a long confirmation beep and the
entire memory is transferred.
Notes
•
If there are already 50 numbers stored in the Phone Directory receiving the
transferred number one by one from the other Phone Directory,
“RECEIVER’S MEMORY IS FULL” will appear on the display and five
short error beeps will be heard to indicate that the transfer was unsuccessful.
To make the transfer possible, erase one of the stored phone numbers existing
in the Phone Directory (see page 49).
•
•
If the transfer is unsuccessful, “ERROR” will appear on the display, and five
short error beeps will be heard. Move the sending unit closer to the receiving
unit, make sure the receiving unit is not in use, and then start over the
procedure.
To check the station number assigned to the cordless handset, see page 26.
Telephone Features 51US
Download from Www.Somanuals.com. All Manuals Search And Download.
Sw it ch in g t h e p h o n e s d u rin g a ca ll
You can easily switch between the cordless handset and the base
phone, or between the cordless handsets without disconnecting the
call.
Sw it ch in g fro m t h e b a se p h o n e t o t h e
co rd le ss h a n d se t
1
Press (HOLD) on the base
phone.
The call is on hold and “HOLD”
appears on the display.
2
Pick up the cordless handset
from the charger (When Quick
talk is set to “ON”; see page 40),
or press (TALK) or (HOLD) on
the cordless handset.
You can continue talking to the
caller through the cordless
handset.
(SPEAKERPHONE)
Sw it ch in g fro m t h e co rd le ss h a n d se t t o t h e
b a se p h o n e
1
Press (HOLD) on the cordless
handset.
The call is on hold and “HOLD”
appears on the display.
2
Pick up the handset from the
base phone, or press
(SPEAKERPHONE) or (HOLD)
on the base phone.
(TALK)
You can continue talking to the
caller through the base phone.
52US
Telephone Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Sw it ch in g fro m t h e co rd le ss h a n d se t t o
a n o t h e r co rd le ss h a n d se t (Wh e n t h e syst e m
h a s a n a d d it io n a l co rd le ss h a n d se t )
1
2
Press (HOLD) on the cordless handset.
The call is on hold and “HOLD” appears on the display.
Pick up another cordless handset from the charger (When
Quick talk is set to “ON”; see page 40), or press (TALK) or
(HOLD) on the cordless handset.
You can continue talking to the caller through the cordless
handset.
Telephone Features 53US
Download from Www.Somanuals.com. All Manuals Search And Download.
In t e rco m Op e ra t io n
Ta lkin g b e t w e e n t h e p h o n e s – In t e rco m
You can make an intercom call between the cordless handset and base phone, or
between the cordless handsets. You can start the intercom from any phone.
Ta lkin g fro m t h e co rd le ss h a n d se t t o t h e b a se p h o n e
Example: Making intercom call from the
cordless handset whose station
number is 1 to the base phone.
1
2
Press (INTERCOM).
When the system has one cordless handset
Skip this step.
When the system has an additional
cordless handset
Turn Jog Dial to choose “TO BASE”, and
then press Jog Dial.
3
4
The cordless handset and base phone ring
and “** INTERCOM 0 **” appears on the
display of the cordless handset and
“** INTERCOM 1 **” appears on the
display of the base phone.
When a person at the base phone picks up
the handset from the base phone, or presses
(SPEAKERPHONE) or (INTERCOM), you can
talk with each other.
When you are done talking, replace the
cordless handset on the charger or press
(OFF) on the cordless handset.
If no one answ ers the phone
Press (INTERCOM) again.
Notes
•
If there is an incoming call during intercom conversation between the base
phone and the cordless handset, intercom call will be disconnected, and both
the base phone and the cordless handset will ring.
•
While talking with an outside caller via the base phone, you cannot make an
intercom call. If you press (INTERCOM) on the cordless handset, “NO
CONNECTION” appears on the display and you will hear five short error
beeps.
Tip
You can receive an intercom call on the base phone even when the ringer
volume on the base phone is set to off. The phone will ring at a low level.
54US
Intercom Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Ta lkin g fro m t h e b a se p h o n e t o t h e co rd le ss h a n d se t
Example: Making intercom call from the
base phone to the cordless
handset whose station number is
1.
1
2
Press (INTERCOM).
When the system has one cordless
handset
Skip this step.
When the system has an additional
cordless handset
Turn Jog Dial to choose “TO
3 HANDSET 1”, and then press Jog Dial.
The base phone and cordless handset
ring and “** INTERCOM 1 **”
appears on the display of the base
phone and “** INTERCOM 0 **”
appears on the display of the cordless
handset.
When a person at the cordless handset
picks up the cordless handset from the
charger (When Quick talk is set to
“ON”; see page 40), or presses (TALK)
or (INTERCOM), you can talk with each
4 other.
When you are done talking, replace the
handset in the cradle or press
(SPEAKERPHONE) on the base phone.
If no one answ ers the phone
Press (INTERCOM) again.
Notes
•
If there is an incoming call during intercom conversation between the base
phone and the cordless handset, intercom call will be disconnected, and both
the base phone and the cordless handset will ring.
•
While talking with an outside caller via the cordless handset, you cannot
make an intercom call. If you press (INTERCOM) on the cordless handset,
“NO CONNECTION” appears on the display and you will hear five short
error beeps.
Tip
You can receive an intercom call on the cordless handset even when the ringer
volume on the cordless handset is set to off. The phone will ring at a low level.
co n t in u e d
Intercom Operation 55US
Download from Www.Somanuals.com. All Manuals Search And Download.
Ta lkin g b e t w e e n t h e p h o n e s – In t e rco m (co n t in u e d )
Ta lkin g b e t w e e n t h e co rd le ss h a n d se t s
– Wa lkie -Ta lkie fu n ct io n (Wh e n t h e syst e m h a s a n
a d d it io n a l co rd le ss h a n d se t )
You can make an intercom conversation between a couple of cordless
handsets (Walkie-Talkie function) of the same phone system far from
the base phone (e.g. use out of doors).
Example: Making intercom call from
station number 1 to station
number 2.
1
2
Press (INTERCOM).
Turn Jog Dial to choose “TO
HANDSET 2”, and then press Jog
Dial.
Both cordless handsets ring and
“** INTERCOM 2 **” appears
on the display of the cordless
handset whose station number is 1
and “** INTERCOM 1 **”
appears on the display of the
cordless handset whose station
number is 2.
(TALK)
When a person at the cordless
handset whose station number is 2
picks up the cordless handset from
the charger (When Quick talk is set
to “ON”; see page 40), or presses
(TALK) or (INTERCOM), you can
talk with each other.
3
When you are done talking,
replace the cordless handset on the
charger or press (OFF).
If no one answ ers the phone
Press (INTERCOM) again.
Notes
•
If there is an incoming outer line call during the intercom conversation
between a couple of cordless handsets (Walkie-Talkie function), intercom call
will not be disconnected. When you answer the outer line call, press (OFF) to
end the intercom conversation.
•
To check the station number assigned to the cordless handset, see page 26.
Tip
You can receive an intercom call on the cordless handset even when the ringer
volume is set to off. The cordless handset will ring at a low level.
56US
Intercom Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Tra n sfe rrin g a ca ll
You can transfer a call between the cordless handset and base phone, or between the
cordless handsets without disconnecting the call.
Tra n sfe rrin g fro m t h e co rd le ss h a n d se t t o t h e b a se p h o n e
Example: Transferring a call from the
cordless handset whose station
number is 1 to the base phone.
1
2
Press (INTERCOM).
The call is put on hold.
(OFF)
When the system has one cordless
handset
Skip this step.
When the system has an additional
cordless handset
Turn Jog Dial to choose “TO BASE”,
and then press Jog Dial.
3
The cordless handset and base phone
ring and “** INTERCOM 0 **”
appears on the display of the cordless
handset and “** INTERCOM 1 **”
appears on the display of the base
phone.
4
5
Pick up the handset from the base
phone, or press (SPEAKERPHONE) or
(INTERCOM) on the base phone.
You can talk between the cordless
handset and the base phone.
To talk to the caller with the base
phone, replace the cordless handset on
the charger or press (OFF) on the
cordless handset.
(INTERCOM)
(SPEAKERPHONE)
“TALK” or “SPEAKERPHONE”
appears on the display of the base
phone.
If no one answ ers the phone
Press (INTERCOM) again.
Tip
You can receive an intercom call on the base phone even when the ringer
volume on the base phone is set to off. The base phone will ring at a low level.
co n t in u e d
Intercom Operation 57US
Download from Www.Somanuals.com. All Manuals Search And Download.
Tra n sfe rrin g a ca ll (co n t in u e d )
Tra n sfe rrin g fro m t h e b a se p h o n e t o t h e co rd le ss h a n d se t
Example: Transferring a call from the
base phone to the cordless
handset whose station number
is 1.
1
2
Press (INTERCOM).
The call is put on hold.
When the system has one cordless
handset
Skip this step.
When the system has an
additional cordless handset
Turn Jog Dial to choose “TO
HANDSET 1”, and then press Jog
Dial.
(SPEAKERPHONE)
3
4
The base phone and cordless
handset ring and
“** INTERCOM 1 **” appears on
the display of the base phone and
“** INTERCOM 0 **” appears on
the display of the cordless handset.
Pick up the cordless handset from
the charger (When Quick talk is set
to “ON”; see page 40), or press
(TALK) or (INTERCOM) on the
cordless handset.
(TALK)
(INTERCOM)
You can talk between the base phone
and the cordless handset.
5
To talk to the caller with the cordless
handset, replace the handset in the
cradle or press (SPEAKERPHONE) on
the base phone.
“TALK” appears on the display of
the cordless handset.
If no one answ ers the phone
Press (INTERCOM) again.
Tip
You can receive an intercom call on the cordless handset even when the ringer
volume is set to off. The phone will ring at a low level.
58US
Intercom Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Tra n sfe rrin g b e t w e e n t h e co rd le ss h a n d se t s (Wh e n t h e
syst e m h a s a n a d d it io n a l co rd le ss h a n d se t )
Example: Transferring a call from
station number 1 to station
number 2.
1
2
Press (INTERCOM).
The call is put on hold.
Turn Jog Dial to choose “TO
HANDSET 2”, and then press Jog
Dial.
Both cordless handsets ring and
“** INTERCOM 2 **” appears
on the display of the cordless
handset whose station number is 1
and “** INTERCOM 1 **”
appears on the display of the
cordless handset whose station
number is 2.
(OFF)
3
Pick up the cordless handset
whose station number is 2 from
the charger (When Quick talk is set
to “ON”; see page 40), or press
(TALK) or (INTERCOM) on the
cordless handset.
4 You can talk with each other.
To talk to the caller with the
cordless handset whose station
number is 2, replace the cordless
handset on the charger or press
(OFF) on the cordless handset
whose station number is 1.
“TALK” appears on the display of
the cordless handset whose station
number is 2.
If no one answ ers the phone
Press (INTERCOM) again.
Tip
You can receive an intercom call on the cordless handset even when the ringer
volume is set to off. The cordless handset will ring at a low level.
Intercom Operation 59US
Download from Www.Somanuals.com. All Manuals Search And Download.
Ca lle r ID Fe a t u re s
Un d e rst a n d in g t h e Ca lle r ID se rvice
Caller ID allows the caller’s phone number to be shown on the display
before you answer the call. In order to use this feature, you must first
subscribe to Caller ID service. The name of this service may vary
depending on your telephone company.
To use this feature, be sure to enter the area code (see page 17).
Wh e n yo u re ce ive a ca ll
The phone number appears on the display as shown in the following
example.
If your Caller ID service includes the caller name service or if the
phone number stored in the Phone Directory matches with the Caller
ID data phone number, the caller’s name also appears on the display
(up to 15 letters).
The caller’s name will appear by the name stored in the Phone
Directory if you receive a call from a phone number which is stored in
the Phone Directory.
Caller’s name
SMITH JOHN
MASSAGE RING OFF
Caller’s phone number
1-201-123-4567
NEW
OLD
When you answer the call, the Caller ID display changes to the
“TALK” or “SPEAKERPHONE” display.
Notes
•
The caller’s phone number and/ or name will not appear in the following
cases:
—“UNKNOWN NUMBER/ NAME/ CALLER” (out of area) : when the call is
made through a telephone company which does not offer Caller ID service
(including international calls).
—“BLOCKED NUMBER/ NAME/ CALL” (private) : when the call is
“blocked”. For privacy reasons, many states allow callers the option to
prevent his or her telephone data from being displayed on the other
party’s Caller ID display.
•
If the call is from an office which uses multiple lines, the displayed phone
number may not match the number you use to call the extension.
About the memory match function
The name stored in the Phone Directory will appear on the display and
the ringer sound will change to a higher tone from the second ring if
you receive a call from a phone number which is stored in the Phone
Directory on the base phone or the cordless handset (see page 43).
Note
The memory match function does not work with “UNKNOWN NUMBER/
NAME/ CALLER” or “BLOCKED NUMBER/ NAME/ CALL” calls; and it may
not work with calls made from an office which uses multiple lines because the
number does not always match the one you stored in this phone.
60US
Caller ID Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Lo o kin g a t t h e Ca lle r ID list
The phone stores the data of the last 70 calls received including
“UNKNOWN NUMBER/ NAME/ CALLER” and “BLOCKED
NUMBER/ NAME/ CALL” calls. It keeps track of all calls received;
even if they were not answered.
Vie w in g t h e Ca lle r ID list
You can look through the Caller ID list on both the base phone and the
cordless handset to check the phone number and/ or name of the calls
received. If there is a “NEW” data, the NEW CALL lamp of the base
phone flashes.
1
Turn Jog Dial.
Turn
Press
The display shows the number
of “NEW CALL” (calls which
you have not viewed) and
“OLD CALL” (calls which you
have viewed) calls.
CALLER ID
NEW CALL
OLD CALL
08
12
NEW
OLD
MASSAGE RING OFF
2
Turn Jog Dial down to display
older data or up to display
newer data.
(PGM)
NEW CALL lamp
Notes
•
•
If a 71st call is received, the oldest data is automatically erased.
When you have checked all data, “END OF LIST” appears.
Tip
The number of “NEW CALL” can be confirmed with the standby mode display
of the base phone.
co n t in u e d
61US
Caller ID Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Lo o kin g a t t h e Ca lle r ID list (co n t in u e d )
Era sin g d a t a fro m t h e Ca lle r ID list
Old data will be erased automatically when a 71st call comes in, but
you can also manually erase unnecessary data one by one or erase the
entire list.
To erase the phone number one by one
1 Display the phone number you want to erase
SMITH JOHN
1-201-123-4567
01 7.04 4:53PM
from the Caller ID list (see page 61).
NEW
OLD
MASSAGE RING OFF
2 Press Jog Dial.
(GO BACK)
DIAL
PROGRAM
NEW
OLD
MASSAGE RING OFF
3 Turn Jog Dial to choose “ERASE CALLER ID”,
(GO BACK)
NO
and then press Jog Dial.
YES
NEW
OLD
MASSAGE RING OFF
4 Turn Jog Dial to choose “YES”, and then press
Jog Dial.
You hear a long confirmation beep and the data
is erased.
Note
Do not allow more than 60 seconds to elapse during the operation procedure.
Tip
When you select “(GO BACK)”, you can return to the previous set display by
pressing Jog Dial.
62US
Caller ID Features
Download from Www.Somanuals.com. All Manuals Search And Download.
To erase the entire list at once
Entire Caller ID list deletion can only be made on the cordless handset.
Note that Caller ID data in the list that has not been viewed will also
be erased.
1 Press (PGM).
2 Turn Jog Dial to choose “MEMORY
(GO BACK)
SEND ALL DIR
ERASE ALL CID
MANAGE”, and then press Jog Dial.
NEW
OLD
MASSAGE RING OFF
3 Turn Jog Dial to choose “ERASE ALL CID”,
(GO BACK)
NO
ERASE CALLER ID
and then press Jog Dial.
NEW
OLD
MASSAGE RING OFF
4 Turn Jog Dial to choose “ERASE CALLER ID”,
and then press Jog Dial.
You hear a long confirmation beep and the
entire list is erased.
Notes
•
•
Do not allow more than 60 seconds to elapse during the operation procedure.
When “ERROR” appears on the display and five short error beeps are heard
after Jog Dial is pressed in step 4, move the cordless handset closer to the
base phone, make sure the base phone is not in use, and then start over the
procedure.
Tip
When you select “(GO BACK)”, you can return to the previous set display by
pressing Jog Dial.
63US
Caller ID Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Usin g t h e Ca lle r ID list
By using the Caller ID list, you can call back a phone number from the
Caller ID list easily or store numbers from the Caller ID list into the
Phone Directory.
Ca llin g b a ck a n u m b e r fro m t h e Ca lle r ID list
1
Display the phone number you
want to call from the Caller ID
list (see page 61).
Turn
Press
SMITH JOHN
1-201-123-4567
01 7.04 4:53PM
NEW
OLD
MASSAGE RING OFF
2
3
Press Jog Dial.
(GO BACK)
DIAL
PROGRAM
(TALK)
NEW
OLD
MASSAGE RING OFF
Turn Jog Dial to choose “DIAL”,
and then press Jog Dial.
The phone automatically dials
the displayed number.
(EZ ACCESS)
Notes
•
If the area code is not entered, “ENTER AREA CODE” will appear on the
display, and you will not be able to call back. Enter the area code (see page
17).
•
•
Do not allow more than 60 seconds to elapse during the operation procedure.
If the number displayed in step 1 is not the one you should call back, you can
change the number of digits of the phone number as described on page 66.
•
If the phone is connected to a Private Branch Exchange (PBX), you may not
be able to call back from the Caller ID list because an outside line access digit
is necessary.
Tips
•
You may press (TALK) on the cordless handset (on the base phone, pick up
the handset or press (SPEAKERPHONE)) to make a call instead of doing steps
2 and 3.
•
If an access number of the long distance call is set up with the EZ access
function, you can add the access number to the phone number and make a
call by pressing (EZ ACCESS) after step 3. For setting up the EZ access
function, see page 23.
•
When you select “(GO BACK)”, you can return to the previous set display by
pressing Jog Dial.
64US
Caller ID Features
Download from Www.Somanuals.com. All Manuals Search And Download.
St o rin g a n u m b e r o f t h e Ca lle r ID list in t o
t h e Ph o n e Dire ct o ry
1 Display the name and phone number you want
SMITH JOHN
1-201-123-4567
01 7.04 4:53PM
to store from the Caller ID list (see page 61).
NEW
OLD
MASSAGE RING OFF
2 Confirm the number and press Jog Dial.
(GO BACK)
DIAL
PROGRAM
NEW
OLD
MASSAGE RING OFF
3 Turn Jog Dial to choose “PROGRAM”, and then
SMITH JOHN_
ABCDEFGHIJKLMN
OPQRSTUVWXYZ
press Jog Dial.
The cursor “_” is at the right of the name.
NEW
OLD
MASSAGE RING OFF
Enter or change the name, if necessary (see page
48).
4 Press (PGM). (Press (PROGRAM) on the base
SMITH JOHN
12011234567_
phone.)
The cursor is at the right of the phone number.
NEW
OLD
MASSAGE RING OFF
Enter or change the phone number, if necessary
(see page 48).
5 Press (PGM) (or (PROGRAM)).
You hear a long confirmation beep and the
name and number are stored.
co n t in u e d
Caller ID Features
65US
Download from Www.Somanuals.com. All Manuals Search And Download.
Usin g t h e Ca lle r ID list (co n t in u e d )
Notes
•
If the area code is not entered, “ENTER AREA CODE” will appear on the
display, and you will not be able to store into the Phone Directory. Enter the
area code (see page 17).
•
•
Do not allow more than 60 seconds to elapse during the operation procedure.
If the number displayed in step 1 is not the one you should store, you can
change the number of digits of the phone number as described below.
•
If the phone is connected to a Private Branch Exchange (PBX), you may need
to add an outside line access digit.
Tip
When you select “(GO BACK)”, you can return to the previous set display by
pressing Jog Dial.
To ch a n g e t h e n u m b e r o f d ig it s o f t h e p h o n e
n u m b e r
If the number of digits of the phone number in the Caller ID list is
different from the actual phone number, you need to adjust the
number of digits of the phone number to call back or store into the
Phone Directory.
1 While the phone number from the Caller ID list is displayed,
press (#) repeatedly until the phone number with the
correct number of digits appears on the display.
Each time you press (#), the number of digits changes as
follows:
When the home area code and the local area code do
not match
SMITH JOHN
1-201-123-4567
SMITH JOHN
201-123-4567
01 7.04 4:53PM
NEW
01 7.04 4:53PM
NEW
OLD
MASSAGE RING OFF
OLD
MASSAGE RING OFF
SMITH JOHN
123-4567
SMITH JOHN
1-123-4567
01 7.04 4:53PM
NEW
01 7.04 4:53PM
NEW
OLD
MASSAGE RING OFF
OLD
MASSAGE RING OFF
66US
Caller ID Features
Download from Www.Somanuals.com. All Manuals Search And Download.
When the home area code matches
SMITH JOHN
123-4567
SMITH JOHN
1-201-123-4567
01 7.04 4:53PM
01 7.04 4:53PM
NEW
OLD
MASSAGE RING OFF
NEW
OLD
MASSAGE RING OFF
SMITH JOHN
1-123-4567
SMITH JOHN
201-123-4567
01 7.04 4:53PM
NEW
01 7.04 4:53PM
NEW
OLD
MASSAGE RING OFF
OLD
MASSAGE RING OFF
When the local area code matches
SMITH JOHN
201-123-4567
SMITH JOHN
1-123-4567
01 7.04 4:53PM
01 7.04 4:53PM
NEW
OLD
MASSAGE RING OFF
NEW
OLD
MASSAGE RING OFF
SMITH JOHN
1-201-123-4567
SMITH JOHN
123-4567
01 7.04 4:53PM
OLD
01 7.04 4:53PM
MASSAGE RING OFF
NEW
MASSAGE RING OFF
NEW
OLD
2 Continue the operation to call or store the phone number
with the correct number of digits (pages 64 and 65).
Notes
•
You need to adjust the number of digits each time you call back from the
Caller ID list as the changes to the Caller ID data is not stored in memory.
•
You may not be able to change the number of digits depending on the Caller
ID data.
67US
Caller ID Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Usin g “ Ca lle r ID w it h ca ll w a it in g ”
se rvice
This telephone is compatible with the “Caller ID with call waiting”
service. Make sure that your telephone company offers this service.
Like the basic Caller ID service, you need to subscribe to “Caller ID
with call waiting” in order to use this service.
Even though you may have already subscribed to “Caller ID” and
“call w aiting” as tw o separate services, you need to request a
subscription to “Caller ID w ith call w aiting” as a single service.
This is a new service that combines the two services.
Even though you now have a “Caller ID w ith call w aiting”
compatible phone, unless you subscribe to the combined “Caller ID
w ith call w aiting” service, you w ill not be able to see the name
and number of the second caller.
When a new call comes in while you are talking, the caller’s name
and/ or phone number of the new call appears on the display for about
20 seconds.
To sw itch to another caller
1
2
To switch to the new caller,
press (CALL WAITING/FLASH).
To switch back to the first caller,
press (CALL WAITING/FLASH)
again.
68US
Caller ID Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Usin g vo ice m a il se rvice
If you subscribe to your telephone company’s message service which
includes this feature, the display will show that you have messages
waiting to be retrieved.
If yo u h a ve m e ssa g e s
“MESSAGES WAITING” appears
on the display on the cordless
handset, and the VOICE MAIL
lamp on the base phone flashes.
The display and the VOICE MAIL
lamp go off when you retrieve your
messages.
VOICE MAIL lamp
Note
You cannot use this feature, if you have not subscribed to your telephone
company’s message service. For details on the availability of this service, please
ask your telephone company.
If the VOICE MAIL lamp remains flashing
If this lamp does not go off (e.g. When you retrieve your messages
with other phones), you can go off the lamp manually.
To go off the VOICE MAIL lamp
1 Press (PGM) on the cordless handset.
2 Turn Jog Dial to choose “MESSAGE INDIC.”,
(GO BACK)
INDICATOR OFF
RESET
and then press Jog Dial.
NEW
OLD
MASSAGE RING OFF
3 Press Jog Dial.
The VOICE MAIL lamp on the base phone goes
off, and you hear a long confirmation beep.
co n t in u e d
Caller ID Features
69US
Download from Www.Somanuals.com. All Manuals Search And Download.
Usin g vo ice m a il se rvice (co n t in u e d )
If you move or change your telephone company
Message waiting signals are sent in one of two ways: FSK signaling or
“stutter” signaling (Your telephone company can provide you with
more information about your service).
The first time this phone receives a voice mail message, it will set itself
to the FSK service and will lock out the stutter service if your
telephone company is in FSK service.
When you move or change your telephone company, you need to
perform the following procedure. The phone will returns to ready state
for either FSK or stutter dial tone voice mail recognition.
To reset this phone
1 Perform step 1 and 2 on page 69.
2 Turn Jog Dial to choose “RESET”, and then press
INDICATOR OFF
RESET
Jog Dial.
You hear a long confirmation beep and the
phone is reset.
NEW
OLD
MASSAGE RING OFF
70US
Caller ID Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Ad d it io n a l In fo rm a t io n
Mo u n t in g t h e b a se p h o n e o n a w a ll
1
1
2
Reverse the hang-up tab.
Hang-up tab
Plug the telephone line cord to
the LINE jack and the AC power
adaptor to the DC IN 9V jack,
and hook the cords. Use the
shorter cord for mounting.
2
3
Attach the wall bracket to the
center of the base phone.
Align the f marks of the wall
bracket with those of the base
phone.
AC pow er
adaptor cord
4
5
Plug the telephone line cord to
the telephone outlet, and hook
the base phone to the wall plate.
Telephone
line cord
Plug the AC power adaptor to
an AC outlet. Then raise the
antenna so that it points
towards the ceiling.
3
4, 5
1
2
Wall plate
Wall bracket
Telephone
line cord
AC outlet
AC pow er
adaptor
Tip
To remove the wall bracket, press the lower tabs.
Additional Information 71US
Download from Www.Somanuals.com. All Manuals Search And Download.
Ca rryin g t h e co rd le ss h a n d se t b y t h e
b e lt clip
You can hang the cordless handset on the belt using the belt clip.
Open the belt clip of the cordless
handset by pressing the top of it,
and then attach the cordless handset
to the belt.
Using the headset
You can talk on the cordless
handset without using your hands
by connecting a headset (optional)
to the I (HEADSET) jack on the
I (HEADSET)
cordless handset.
jack
72US Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
No t e s o n p o w e r so u rce s
On battery pack
For the customers in the USA
• Store the battery pack at a
temperature between 41°F (5°C) and
95°F (35°C) for best performance.
RECYCLING NICKEL-CADMIUM
BATTERIES
Nickel-Cadmium batteries
are recyclable. You can help
preserve our environment
by returning your
unwanted batteries to your
nearest point for collection,
recycling or proper
• If you do not use the cordless handset
for a long period of time, remove the
battery pack after charging for more
than 12 hours.
disposal.
Note: In some areas the disposal of nickel-
cadmium batteries in household or
business trash may be prohibited.
On pow er failure
During a power interruption, you
cannot make or receive calls.
RBRC (Rechargeable Battery Recycling
Corporation) advises you about spent battery
collection by the following phone number.
Call toll free number: 1-800-822-8837
(United States and Canada only)
Caution: Do not handle damaged or leaking
nickel-cadmium batteries.
Additional Information 73US
Download from Www.Somanuals.com. All Manuals Search And Download.
Ma in t e n a n ce
• Clean the cabinets with a soft cloth
slightly moistened with water or a
mild detergent solution. Do not use
any type of abrasive pad, scouring
powder or solvent such as alcohol or
benzine as they may damage the
finish of the cabinet.
• If the charge terminals of the charger
and cordless handset are soiled, wipe
them with a soft cloth.
If you have any questions or problems
concerning your phone, please consult
your nearest Sony dealer.
74US Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Tro u b le sh o o t in g
If you’ve experienced any of the following difficulties while using your
phone, use this troubleshooting guide to help you remedy the problem.
Should any problem persist, consult your nearest Sony dealer.
Symptom
Remedy
The base phone does not
operate properly.
• Make sure the AC-T46 Sony AC power adaptor is
connected to the base phone and an AC outlet. Do not
use the AC-T127 Sony AC power adaptor with the
base phone.
You hear five short error
beeps when you press (TALK).
• Make sure you have set up the base phone correctly
(page 11).
• Move the cordless handset closer to the base phone.
• Make sure the base phone or another cordless handset
is not making intercom call or outside call.
• Make sure another cordless handset is not checking
the Caller ID list, etc.
• Make sure the telephone line cord is securely
connected to the telephone outlet.
You hear no dial tone.
• Make sure the battery is fully charged (page 14).
• Make sure the dialing mode is set correctly (page 16).
The phone does not connect at
all, even though the number
you dial is correct.
• Make sure the dialed number is really the one you
want to dial.
The phone does not redial
correctly.
• During phone conversation, press (VOL +) on the base
phone to increase the speakerphone volume.
You cannot hear anything from
the speakerphone.
• Make sure that the registered call number is correct.
Even by pressing (EZ ACCESS),
the desired call is not being
made.
• Set the ringer volume on the cordless handset to high
or low. (page 40, 41)
The cordless handset does not
ring.
• The battery may be weak. Charge the battery for more
than 12 hours (page 14).
• Make sure you have set up the base phone correctly
(page 11).
• Move the cordless handset closer to the base phone,
and confirm a dial tone is heard by pressing (TALK)
on the cordless handset.
• Press (VOL +) on the base phone to increase the ringer
volume.
The base phone does not ring.
• Make sure the telephone line cord is securely
connected to the telephone outlet.
co n t in u e d
Additional Information 75US
Download from Www.Somanuals.com. All Manuals Search And Download.
Tro u b le sh o o t in g (co n t in u e d )
Symptom
Remedy
You hear interference during
conversation.
• Move the cordless handset closer to the base phone.
•
Place the base phone away from noise sources
(page 11).
• Place the base phone so that the antenna keeps away
from metal products.
You hear a beep every second
during a conversation and “ ”
appears on the display.
• This is the out-of-range alarm. Move the cordless
handset closer to the base phone within 30 seconds.
• The battery is weak. Charge the battery for more than
12 hours (page 14).
You hear a beep twice per
second and “BATTERY LOW”
appears on the display.
• The battery may be week. Charge the battery for more
than 12 hours (page 14).
• Move the cordless handset closer to the base phone.
• Place the base phone away from noise sources
(page 11).
The cordless handset does not
ring when you use the intercom
from the base phone or an
additional cordless handset,
and the base phone does not
ring when you use the intercom
from the cordless handset.
• Make sure a station number is assigned on the
additional cordless handset.
• Make sure another cordless handset or base phone is
not in use.
• The base phone is being used to converse with an
outside caller.
• Move the cordless handset close to the base phone.
When pressing (INTERCOM) on
the cordless handset, you hear
five short error beeps and
cannot make an intercom call.
• Register the additional cordless handset to the base
phone (page 25).
• Move the cordless handsets closer to each other.
• Check the battery. If the battery becomes weak, charge
it.
You cannot make an Intercom
conversation between a couple
of cordless handsets (Walkie-
Talkie function).
• Make sure the system ID is correct.
• Make sure the cordless handset is fully charged
(page 14).
You cannot assign a station
number on the additional
cordless handset.
• Make sure all the cordless handset is placed close to
the base phone.
• Make sure the handset is placed in the cradle of the
base phone.
• Place the cordless handset on the charger. The station
number of the cordless handset appears on the
display.
You do not know the station
number of the cordless handset.
• Attach the supplied station number sticker on the
cordless handset for remembrance’ sake.
76US Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
The caller’s name and/ or
• Make sure you have subscribed to Caller ID service.
phone number does not appear • Caller ID service may not work when the phone is
on the display.
connected to a Private Branch Exchange (PBX).
• The call is made through company which does not
offer Caller ID service. “UNKNOWN NUMBER/
NAME/ CALLER” will appear on the display.
• The call was “blocked.” “BLOCKED NUMBER/
NAME/ CALL” will appear on the display.
• You have answered the call while “** RINGING **”
was displayed. Please answer the call after the second
ringer sound.
The caller’s name and/ or
phone number does not
appear on the display during
call waiting.
• Make sure you have subscribed to “Caller ID with call
waiting” service (page 68).
• Make sure nobody is talking with another phone on
the same telephone line.
You cannot dial the number
from the Caller ID list.
• Make sure you entered your area code correctly
(page 17).
• You may need to change the number of digits of the
phone number (page 66).
• This function may not work when the phone is
connected to a Private Branch Exchange (PBX).
The memory match function
does not work.
• If the call is from an office which uses multiple lines,
the phone number may not match the number you
put in the memory.
• If you have stored phone number with an outside line
access digit in the Phone Directory because the phone
is connected to a Private Branch Exchange (PBX), the
phone number will not match the Caller ID data.
• If you have stored phone number of less than 7 digits
in the Phone Directory, the phone number will not
match the Caller ID data.
You cannot use voice mail
service.
• Make sure you have subscribed to voice mail service.
• If you move or change your telephone company, reset
this phone.
co n t in u e d
Additional Information 77US
Download from Www.Somanuals.com. All Manuals Search And Download.
Tro u b le sh o o t in g (co n t in u e d )
Symptom
Remedy
The CHARGE lamp on the
charger does not light up when
you place the cordless handset
to charge.
• Wipe the charge terminals of the charger and the
cordless handset with a soft cloth for better contact of
the charge terminals.
• Make sure the cordless handset is placed on the
charger properly.
• Make sure the cordless handset is placed on the
charger with front side facing forward.
• Use only the supplied AC-T127 AC power adaptor.
The battery duration is short.
• The battery pack was charged less than 12 hours (due
to power failure, etc.).
• The usage life of the battery has expired and needs
replacement.
• Use only the supplied AC-T127 AC power adaptor.
Note
Should any problems persist, press RESET on the bottom of the base phone
with the tip of a toothpick or some other sharp instrument. This has no effect on
the memory in the base phone and handset.
RESET
78US Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Sp e cifica t io n s
General
Base phone
Spread method
Power source
Direct-Sequence Spread-Spectrum
Access method
DC 9V from AC power adaptor
AC-T46
FDMA-TDD
Frequency band
2.4075 - 2.4720 GHz
Operating channel
40 channels
Dimensions
Approx. 7 3⁄8 x 3 3⁄4 x 8 1⁄8 inches (w/ h/ d),
antenna excluded
(approx. 187 x 93 x 206 mm)
Antenna: Approx. 4 3⁄ 8 inches
(approx. 108 mm)
Mass
Approx. 1 lb 8 oz
Dial signal
Tone, 10 PPS (pulse) selectable
Supplied accessories
See page 10.
(approx. 680 g), wall bracket excluded
Charger
Power source
DC 9V from AC power adaptor
AC-T127
Dimensions
Approx. 3 1⁄4 x 2 5⁄8 x 4 1⁄8 inches (w/ h/ d)
(approx. 80 x 64 x 102 mm)
Mass
Cordless handset
Power source
Rechargeable battery pack BP-T38
Battery life
Standby: Approx. 6 days
Talk:
Approx. 5 hours
Battery charging time
Approx. 12 hours
Dimensions
Approx. 2 3⁄8 x 6 5⁄8 x 1 15⁄16 inches (w/ h/ d),
antenna excluded
(approx. 58 x 166 x 48 mm)
Antenna: Approx. 2 7⁄8 inches
(approx. 72 mm)
Approx. 2.7 oz (approx. 75 g)
Design and specifications are subject to
change without notice.
Mass
Approx. 8.1 oz
(approx. 230 g), battery included
79US
Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
In d e x
A
D
M
Adjusting volume
cordless handset volume
33, 40
Day and time 21
Dialing mode
choosing 16
Making calls 32
Memory match function
60
handset volume 36, 41
ringer volume 40, 41
Mounting the base phone
on a wall 71
switching to the tone
temporarily 33
speakerphone volume
36, 41
Area code 17
Directory
Phone Directory 43
N, O
NEW CALL 61
E, F, G
NO CONNECTION 32
B
Erasing
Caller ID data 62
phone numbers dialed
38
Phone Directory 49
P, Q
Package contents 10
Phone Directory 43
Pulse dialing 16
Battery pack
charging 14
duration 15
BLOCKED NUMBER/
NAME/ CALL 60
EZ Access function 23, 33
R
C
H
Receiving calls 39
Redialing 37
Registering additional
cordless handsets 25
Call waiting service 33, 40
Caller ID 60
Headset 33, 39, 72
Hold 33, 40
Home area code 17
Caller ID list 61
calling back 64
memory match function
60
storing in Phone
Directory 65
Caller ID with call waiting
68
Carrying the cordless
S
I, J, K
Identifying the parts 28
Intercom 54
Setting up
base phone 11
cordless handset 14
Speakerphone 36
Storing Caller ID list into
Phone Directory 65
L
Language of the display
27
Local area code 19
handset by the belt clip 72
Connection 12
Switching phones during a
call 52
Location, base phone 11
80US Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
T
Talking between the
phones 54
Tone dialing
dialing mode 16
switching to 33
Transferring a call 57
Troubleshooting 75
U
UNKNOWN NUMBER/
NAME/ CALLER 60
V
VOICE MAIL 69
Volume
cordless handset 33, 40
handset 36, 41
ringer 40, 41
speakerphone 36, 41
W, X, Y, Z
Walkie-Talkie function 56
81US
Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
For the customers in the USA
Be sure to save the receipt and attach it to your WARRANTY card when having
your equipment repaired at an authorized Sony service center.
For online product registration, please contact
Sony Corporation Printed in Taiwan, R.O.C.
Download from Www.Somanuals.com. All Manuals Search And Download.
|