Sony CRT Television KD 30XS955 KD 32XS945 KD 34SX955 KD 36SX955 User Manual

4-102-728-22(1)  
KD-30XS955 I KD-32XS945 I KD-34XS955 I KD-36XS955  
Operating Instructions  
Sony Corporation http://www.sony.net  
Download from PWrwinwte.dSoinmUa.Sn.uAa. ls.com. All M©an2u0a0l5s SSoenayrcChorAponrdaDtioonwnload.  
WARNING  
Note to CATV System Installer  
To reduce the risk of fire or shock hazard, do not expose the TV to  
rain or moisture.  
This reminder is provided to call the CATV system installer’s  
attention to Article 820-40 of the National Electrical Code (NEC)  
that provides guidelines for proper grounding and, in particular,  
specifies that the cable ground shall be connected to the grounding  
system of the building, as close to the point of cable entry as  
practical.  
CAUTION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
Use of this television receiver for other than private viewing of  
programs broadcast on UHF or VHF or transmitted by cable  
companies for the use of the general public may require  
authorization from the broadcaster/cable company and/or  
program owner.  
ATTENTION  
RISQUE DE CHOC ELECTRIQUE,  
NE PAS OUVRIR  
NOTIFICATION  
PRECAUCION  
RIESGO DE CHOQUE ELECTRICO  
NO ABRIR  
This equipment has been tested and found to comply with the  
limits for a Class B digital device pursuant to Part 15 of the FCC  
Rules. These limits are designed to provide reasonable protection  
against harmful interference in a residential installation. This  
equipment generates, uses, and can radiate radio frequency energy  
and, if not installed and used in accordance with the instructions,  
may cause harmful interference with radio communications.  
However, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be  
determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or more of the  
following measures:  
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,  
DO NOT REMOVE COVER (OR BACK).  
NO USER-SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
This symbol is intended to alert the user to the  
presence of uninsulated “dangerous voltage”  
within the product’s enclosure that may be of  
sufficient magnitude to constitute a risk of  
electric shock to persons.  
Reorient or relocate the receiving antennas.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different  
from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for  
help.  
You are cautioned that any changes or modifications not  
expressly approved in this manual could void your authority  
to operate this equipment.  
This symbol is intended to alert the user to the  
presence of important operating and maintenance  
(servicing) instructions in the literature  
accompanying the appliance.  
Installing  
To prevent internal heat buildup, do not block the ventilation  
openings.  
CAUTION  
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF  
PLUG TO WIDE SLOT, FULLY INSERT.  
Do not install the TV in a hot or humid place, or in a place  
subject to excessive dust or mechanical vibration.  
The AC power cord is attached to the rear of the TV with  
hooks. Do not attempt to remove the cord from these hooks.  
Doing so could cause damage to the TV.  
CAUTION  
When using TV games, computers, and similar products with your  
TV, keep the brightness and contrast functions at low settings. If a  
fixed (non-moving) pattern is left on the screen for long periods of  
time at a high brightness or contrast setting, the image can be  
permanently imprinted onto the screen. Continuously watching  
the same program can cause the imprint of station logos onto the  
TV screen. These types of imprints are not covered by your  
warranty because they are the result of misuse.  
Owner’s Record  
The model and serial numbers are provided on the front of this  
instruction manual and at the rear of the TV. Refer to them  
whenever you call upon your Sony dealer regarding this product.  
Note  
Warning (KD-34XS955 only)  
The CRT in this product employs a protective film on the face. This  
film must not be removed as it serves a safety function and  
removal will increase the risk of serious injury.  
This digital television is capable of receiving analog basic, digital  
basic and digital premium cable television programming by direct  
connection to a cable system providing such programming. A  
security card provided by your cable operator is required to view  
encrypted digital programming. Certain advanced and interactive  
digital cable services such as video-on-demand, a cable operator's  
enhanced program guide and data-enhanced television services  
may require the use of a set-top box. For more information call  
your local cable operator.  
Note on Caption Vision  
This television receiver provides display of television closed  
captioning in accordance with §15.119 of the FCC rules.  
Note on Cleaning the TV  
Clean the TV with a soft, dry cloth. Never use strong solvents such  
as thinner or benzine, which might damage the finish of the  
cabinet.  
This television also includes a QAM demodulator which should  
allow you to receive unscrambled digital cable television  
programming via subscription service to a cable service provider.  
Availability of digital cable television programming in your area  
depends on the type of programming and signal provided by your  
cable service provider.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFEGUARDS  
For your protection, please read these instructions completely, and  
Object and Liquid Entry  
keep this manual for future reference.  
Never push objects of any kind into the set  
through the cabinet slots as they may touch  
dangerous voltage points or short out parts that  
could result in a fire or electric shock. Never spill  
liquid of any kind on the set.  
Carefully observe and comply with all warnings, cautions and  
instructions placed on the set, or described in the operating  
instructions or service manual.  
WARNING  
Attachments  
Do not use attachments not recommended by the  
manufacturer, as they may cause hazards.  
To guard against injury, the following basic safety precautions  
should be observed in the installation, use, and servicing of the set.  
Use  
Do not place any objects, especially heavy objects,  
on top of the set. The object may fall from the set,  
causing injury.  
Power Sources  
This set should be operated only from the type  
of power source indicated on the serial/model  
plate. If you are not sure of the type of electrical  
power supplied to your home, consult your  
dealer or local power company. For those sets  
designed to operate from battery power, refer  
to the operating instructions.  
Cleaning  
Unplug the set from the wall outlet before  
cleaning or polishing it. Do not use liquid  
cleaners or aerosol cleaners. Use a cloth lightly  
dampened with water for cleaning the exterior  
of the set.  
If a snapping or popping sound from a TV set is  
continuous or frequent while the TV is operating,  
unplug the TV and consult your dealer or service  
technician. It is normal for some TV sets to make  
occasional snapping or popping sounds,  
Grounding or Polarization  
This set is equipped with a polarized AC power cord plug (a plug  
having one blade wider than the other), or with a three-wire  
grounding type plug (a plug having a third pin for grounding).  
Follow the instructions below:  
particularly when being turned on or off.  
For the set with a polarized AC power cord plug  
Installation  
This plug will fit into the power outlet only one  
way. This is a safety feature. If you are unable to  
insert the plug fully into the outlet, try reversing  
the plug. If the plug should still fail to fit, contact your electrician to  
have a suitable outlet installed. Do not defeat the safety purpose of  
the polarized plug by forcing it in.  
Always use two or more people to lift or move the set. The set is  
heavy and the bottom surface is flat. Serious injury can result from  
trying to move the set by yourself alone, or from unsteady  
handling. Install the set on a stable, level surface.  
Water and Moisture  
Do not use power-line operated sets near  
water — for example, near a bathtub,  
Alternate Warning  
washbowl, kitchen sink, or laundry tub, in a  
wet basement, or near a swimming pool, etc.  
For the set with a three-wire grounding type AC plug  
This plug will only fit into a grounding-type  
power outlet. This is a safety feature. If you are  
unable to insert the plug into the outlet, contact  
your electrician to have a suitable outlet installed.  
Do not defeat the safety purpose of the grounding plug.  
Accessories  
Do not place the set on an unstable cart, stand,  
tripod, bracket, table or shelf. The set may fall,  
causing serious injury to a child or an adult, and  
serious damage to the set. Use only a cart or stand  
recommended by the manufacturer for the  
specific model of TV. Any mounting of the  
product should follow the manufacturer’s  
instructions, and should use a mounting  
accessory recommended by the manufacturer. An  
appliance and cart combination should be moved  
with care. Quick stops, excessive force, and  
uneven surfaces may cause the appliance and cart  
combination to overturn.  
Overloading  
Do not overload wall outlets, extension cords or  
convenience receptacles beyond their capacity,  
since this can result in fire or electric shock.  
Always turn the set off when it is not to be  
used. When the set is left unattended and  
unused for long periods of time, unplug it  
from the wall outlet as a precaution against  
the possibility of an internal malfunction that  
could create a fire hazard.  
Do not disconnect the antenna or the power cord during a heavy  
storm. Lightning may strike while you are holding the cable or  
cord, causing serious injury. Turn off your TV and wait for the  
weather to improve.  
Disconnect all cables and cords from the set before attempting to  
move the set.  
Do not allow children or pets to climb up onto, or push against, the  
set. The set may fall, causing serious injury.  
Memory Stick  
To protect small children from injury from Memory Stick Media,  
remove all Memory Stick media from the TV’s Memory Stick slot  
and store it in a safe location when it is not in use.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ventilation  
Lightning  
The slots and openings in the cabinet and in the  
back or bottom are provided for necessary  
For added protection for this television receiver during a lightning  
storm, or when it is left unattended and unused for long periods of  
time, unplug it from the wall outlet and disconnect the antenna.  
This will prevent damage to the receiver due to lightning and  
power line surges.  
ventilation. To ensure reliable operation of the set,  
and to protect it from overheating, these slots and  
openings must never be blocked or covered.  
Never cover the slots and openings with a  
cloth or other materials.  
Service  
Damage Requiring Service  
Unplug the set from the wall outlet and refer servicing to qualified  
service personnel under the following conditions:  
Never block the slots and openings by  
placing the set on a bed, sofa, rug or other  
similar surface.  
When the power cord or plug  
is damaged or frayed.  
Never place the set in a confined space, such  
as a bookcase, or built-in cabinet, unless  
proper ventilation is provided.  
If liquid has been spilled into  
the set or objects have fallen into the  
product.  
Do not place the set near or over a radiator  
or heat register, or where it is exposed to direct sunlight.  
Power Cord Protection  
Do not allow anything to rest on or roll over the  
power cord, and do not place the set where the  
power cord is subject to wear or abuse.  
If the set has been exposed to rain or  
water.  
If the set has been subject to excessive  
shock by being dropped, or the cabinet  
has been damaged.  
Antennas  
Outdoor Antenna Grounding  
If the set does not operate normally when  
following the operating instructions.  
Adjust only those controls that are  
specified in the operating instructions.  
Improper adjustment of other controls  
may result in damage and will often  
require extensive work by a qualified  
technician to restore the set to normal  
operation.  
If an outdoor antenna is installed, follow the precautions below. An  
outdoor antenna system should not be located in the vicinity of  
overhead power lines or other electric light or power circuits, or  
where it can come in contact with such power lines or circuits.  
WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM,  
EXTREME CARE SHOULD BE TAKEN TO KEEP FROM  
CONTACTING SUCH POWER LINES OR CIRCUITS AS  
CONTACT WITH THEM IS ALMOST INVARIABLY FATAL.  
Be sure the antenna system is grounded so as to provide some  
protection against voltage surges and built-up static charges.  
Section 810 of the National Electrical Code (NEC) in USA and  
Section 54 of the Canadian Electrical Code in Canada provide  
information with respect to proper grounding of the mast and  
supporting structure, grounding of the lead-in wire to an antenna  
discharge unit, size of grounding conductors, location of antenna  
discharge unit, connection to grounding electrodes, and  
requirements for the grounding electrode.  
When the set exhibits a distinct change in performance, it  
indicates a need for service.  
Servicing  
Do not attempt to service the set yourself since  
opening the cabinet may expose you to dangerous  
voltage or other hazards. Refer all servicing to  
qualified service personnel.  
Antenna Grounding According to the National  
Electrical Code, ANSI/NFPA 70  
Replacement Parts  
When replacement parts are required, be sure the  
service technician certifies in writing that he has  
used replacement parts specified by the  
manufacturer that have the same characteristics as  
the original parts.  
Antenna lead-in wire  
Unauthorized substitutions may result in fire, electric shock or  
other hazards.  
Ground clamp  
Antenna discharge unit  
(NEC Section 810-20)  
Safety Check  
Upon completion of any service or repairs to the  
set, ask the service technician to perform routine  
safety checks (as specified by the manufacturer) to  
determine that the set is in safe operating  
condition, and to so certify. When the set reaches  
the end of its useful life, improper disposal could  
result in a picture tube implosion. Ask a qualified  
service technician to dispose of the set.  
Electric service  
Grounding conductors  
(NEC Section 810-21)  
Ground clamps  
equipment  
Power service grounding electrode  
NEC: National Electrical Code  
system (NEC Art 250 Part H)  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Trademark Information  
WOW, TruSurround and the  
symbol are trademarks of SRS  
Labs, Inc. WOW and TruSurround technology are incorporated  
under license from SRS Labs, Inc.  
Manufactured under license from Dolby  
Laboratories. Dolby and the double-D symbol  
are trademarks of Dolby Laboratories.  
Manufactured under license from BBE Sound, Inc. Licensed by BBE  
Sound, Inc. under USP4638258, 5510752 and 5736897. BBE and BBE  
symbol are registered trademarks of BBE Sound, Inc.  
This TV incorporates High-Definition  
Multimedia Interface (HDMI™)  
technology. HDMI, the HDMI logo and  
High-Definition Multimedia Interface are trademarks or registered  
trademarks of HDMI Licensing LLC.  
CableCARD™ is a trademark of Cable Television Laboratories, Inc.  
Wega, FD Trinitron, Steady Sound, Digital Reality Creation,  
CineMotion, Memory Stick, Memory Stick Duo, Memory Stick  
PRO, Memory Stick PRO Duo, MagicGate, Super Fine Pitch, MID,  
Clear Edge, ClearEdge VM and HD Detailer are trademarks of  
Sony Corporation.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Setting Up the TV  
Overview .....................................................................................................11  
TV Controls and Connectors.......................................................................12  
XS955 Front Panel...........................................................................12  
XS945 Front Panel...........................................................................13  
Basic Connections: Connecting a Cable or Antenna.................................16  
About Using CableCARD .................................................................16  
Cable or Antenna Only ....................................................................17  
Cable and Antenna Only .................................................................18  
Cable Box and Cable Only ...............................................................19  
Cable Box Only................................................................................20  
Connecting Optional Equipment ...............................................................21  
Making Video Connections..............................................................22  
VCR and Cable ................................................................................23  
VCR and Cable Box .........................................................................24  
Two VCRs for Tape Editing ..............................................................26  
Satellite Receiver..............................................................................28  
Camcorder ......................................................................................35  
Audio Receiver ................................................................................36  
DVI-Equipped Device .......................................................................37  
Using the CONTROL S Feature ...................................................................40  
Using CableCARD ........................................................................................41  
About Using CableCARD .................................................................41  
Activating CableCARD Service .........................................................41  
Removing the CableCARD ...............................................................42  
Setting Up the Channel List .......................................................................43  
Using Initial Setup............................................................................43  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Features  
Overview .....................................................................................................51  
Watching TV ................................................................................................52  
Using Additional Program Guide Options.........................................54  
Using Screen Mode (32/36 models only) ...................................................57  
Using Favorite Channels.............................................................................58  
Using the Channel Menu.................................................................58  
Using the Favorite Channels Guide ..................................................58  
Using Other Equipment with Your TV Remote Control...........................59  
All Equipment..................................................................................59  
Using the Memory Stick Viewer  
About Memory Stick...................................................................................61  
Features ..........................................................................................61  
Memory Stick Functionality..............................................................62  
Trademark Information....................................................................63  
Inserting and Removing a Memory Stick ..................................................64  
Inserting a Memory Stick .................................................................64  
Using the Memory Stick Index .........................................................67  
Viewing Photos ...........................................................................................68  
Photo Menu Bar Options .................................................................69  
Using Rotate....................................................................................70  
Movie Controls................................................................................71  
Movie Menu Bar Options.................................................................72  
Memory Stick Index Menu Bar Options ....................................................73  
Slide Show Menu Options ...............................................................73  
Contents Menu Options ..................................................................74  
Memory Stick Menu ........................................................................74  
Notes on Using Memory Stick Media ........................................................75  
About DCF File Names.....................................................................75  
Memory Stick Precautions................................................................76  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Menus  
Using the Video Menu................................................................................78  
Using the Audio Menu ...............................................................................80  
Using the Screen Menu (30/34 models only).............................................82  
Using the Screen Menu (32/36 models only).............................................83  
Selecting Parent Menu Options........................................................86  
US Models:Selecting Custom Rating Options ...................................87  
Viewing Blocked Programs ..............................................................87  
Other Information  
Overview .....................................................................................................95  
Glossary .......................................................................................................96  
Contacting Sony..........................................................................................97  
Troubleshooting..........................................................................................97  
Channels .........................................................................................98  
CableCARD .....................................................................................98  
Memory Stick ..................................................................................99  
Audio ............................................................................................100  
Video ............................................................................................101  
General .........................................................................................101  
Specifications ............................................................................................103  
Optional Accessories......................................................................104  
Index ..........................................................................................................105  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introducing the FD Trinitron Wega  
Overview  
This chapter describes the contents of the package in which the TV is  
shipped and provides an overview of the features of your Wega TV.  
Presenting the FD TrinitronWega  
The FD Trinitron Wega (pronounced VAY-GAH) is characterized by  
outstanding contrast, uncompromising accuracy, and corner-to-  
corner detail.  
You will recognize the superiority of Wega technology almost  
immediately. The first thing you will probably notice is minimal glare  
from the flat picture tube. This flat-screen technology improves  
picture detail without distortion, unlike conventional curved screens.  
The FD Trinitron delivers outstanding image detail not only at the  
screen center, but also at the corners — so you can enjoy a bright,  
clear picture from any location in a room.  
Package Contents  
Features  
Along with your new Trinitron TV, the packing box contains a remote  
control and two AA (R6) batteries. These items are all you need to set  
up and use the TV.  
Some of the features that you will enjoy with your new TV include:  
Built-in Digital Television Receiver: You can watch digital  
television programs and enjoy the improved audio/video quality  
offered by these programs. With high-definition signal reception,  
you can watch TV signals broadcast in HDTV for the clearest  
possible broadcast picture.  
CableCARD slot: Provides cable subscribers with access to  
digitally encrypted cable channels — without the need for a set-  
top box — that will enable you to receive not only standard  
definition but also high definition television. The CableCARD,  
which is provided by your cable TV company, is inserted into the  
TV’s rear panel CableCARD slot. After the service is activated  
with your cable TV company, the card replaces the need for a  
separate set-top box. (Check with your cable TV company about  
CableCARD service details, limitations, pricing, and availability.  
For more information about CableCARD in this manual, see  
pages 16 and 41.)  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Screen Mode: Enables you to resize the picture.  
XS955 models only  
Super Fine Pitch CRT:  
Created especially for  
displaying high resolution pictures, the new Super Fine Pitch  
CRT — along with a new electron gun and high intensity  
luminescent phosphor — improves image resolution, providing  
the highest picture quality reproduction from corner to corner.  
®
DRC (Digital Reality Creation) Multifunction: Unlike  
conventional line doublers, the DRC Multifunction feature  
replaces the signal’s NTSC waveform with the near-HD  
equivalent, while doubling the number of vertical and horizontal  
lines. This results in four times the density for quality sources,  
such as DVD, satellite, and digital camcorders. The Video Menu  
allows you to select interlaced, progressive, or CineMotion™  
output.  
Favorite Channels: Allows you to select from 16 of your favorite  
channels.  
ClearEdge VM Velocity Modulation: Sharpens picture  
definition by enhancing vertical lines.  
®
Steady Sound : Equalizes volume levels so there is consistent  
output between programs and commercials.  
®
Memory Stick Viewer: Lets you watch digital photo (JPEG) and  
movie (MPEG1) files that are stored on Memory Stick media.  
Component Video Inputs: Offers the best video quality for DVD  
(480p, 480i), and digital set-top box (HD1080i, 720p) connections.  
HD Detailer : Wideband video amplifier has a high bandwidth  
frequency rating, which allows it to send more video information  
to the screen, resulting in finer picture quality, especially for HD  
sources.  
CineMotion : Reverse 3-2 pulldown processing provides  
optimal picture quality for film-based sources (media originally  
shot in 24 frames-per-second format).  
Parental Control: V-Chip technology allows parents to block  
unsuitable programming from younger viewers.  
HDMI (High-Definition Multimedia Interface): Provides an  
uncompressed, all-digital audio/video interface between this TV  
and any HDMI-equipped audio/video component, such as a set-  
top box, DVD player, and A/V receiver. HDMI supports  
enhanced, or high-definition video, plus two-channel digital  
audio.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                           
Setting Up the TV  
Overview  
This chapter includes illustrated instructions for setting up your TV.  
Topic  
Page(s)  
12-15  
TV Controls and Connectors  
Basic Connections: Connecting a Cable or Antenna  
16-20  
VCR and Cable  
VCR and Cable Box  
Satellite Receiver and VCR  
Camcorder  
Audio Receiver  
DVI-Equipped Device  
HDMI-Equipped Device  
24  
26  
28  
30  
34  
35  
36  
37  
38  
Connecting a Device with an Optical IN Connector  
Using the CONTROL S Feature  
Using CableCARD  
39  
40  
41  
43  
Setting Up the Channel List  
About the AC  
Power Cord  
The AC power cord is attached to the rear of the TV with a hook. Use  
caution when removing the AC plug from its holder. Gently slide the  
plug upward to remove it from the hook. Once removed, the AC  
power plug should automatically disengage from its stored location.  
Do not plug in the AC power cord until you have made all other  
connections.  
You can detach  
the cord from  
this hook  
AC power cord  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
TV Controls and Connectors  
XS955 Front Panel  
The following description applies to models KD-30/34/36XS955  
only.  
1
2
3
4
5 6  
7
8
9
q;  
qa  
qs qd  
qf  
STAND BY  
TIMER  
POWER  
STD/DUO  
VIDEO  
2
INPUT  
+
VOLUME CHANNEL  
_
TV/VIDEO  
L(MONO) – AUDIO – R  
VIDEO  
S VIDEO  
MENU  
Item  
1 S VIDEO  
VIDEO 2 INPUT  
Description  
Connects to the S VIDEO OUT jack on your camcorder or other video  
equipment that has S VIDEO. Provides better picture quality than composite  
video (2).  
2 VIDEO/L(MONO)-AUDIO-R Connects to the composite A/V output jacks on your camcorder or other video  
VIDEO 2 INPUT  
equipment.  
3 MENU  
Press to display the Menu. Press again to exit from the Menu. For details, see  
“Using the Menus” on page 77.  
Vv B b  
Press Vv B b to move the TV’s on-screen cursor.  
4
5
Press to select an item in the TV’s Menu.  
6
Press to display the Memory Stick Menu. For details, see “Using the Memory  
Stick Viewer” on page 61.  
7 TV/VIDEO  
Press repeatedly to cycle through the video equipment connected to the TV’s  
video inputs.  
8 -VOLUME +  
Press to adjust the volume.  
9 -CHANNEL+  
Press to scan through channels. To scan quickly through channels, press and  
hold down either CHANNEL button.  
0 PRO STD/DUO  
Memory Stick insertion slot. For details, see “Inserting and Removing a Memory  
Stick” on page 64.  
qa Memory Stick LED  
qs TIMER/STAND BY LED  
When lit, indicates that the Memory Stick is being read. (Do not remove the  
Memory Stick when the indicator is lit.)  
Blinks when the TV is turned on, then shuts off when the picture is displayed. If  
the LED blinks continuously, this may indicate the TV needs service (see  
“Contacting Sony” on page 97). When lit, indicates one of the timers is set. When  
the timer is set, this LED will remain lit even if the TV is turned off. For details,  
see page 92.  
qd Infrared Receiver (IR)  
Receives IR signals from the TV’s remote control.  
Press to turn on and off the TV.  
qf POWER  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                       
XS945 Front Panel  
The following description applies to model KD-32XS945 only.  
1
2
3
4
5 6  
7
8
9
q;  
qa  
qs qd qf  
qg  
POWER  
STD/DUO  
POWER  
TIMER  
VIDEO  
2
INPUT  
+
VOLUME CHANNEL  
_
TV/VIDEO  
L(MONO) – AUDIO – R  
VIDEO  
S VIDEO  
MENU  
Item  
1 S VIDEO  
VIDEO 2 INPUT  
Description  
Connects to the S VIDEO OUT jack on your camcorder or other video  
equipment that has S VIDEO. Provides better picture quality than composite  
video (2).  
2 VIDEO/L(MONO)-AUDIO-R Connects to the composite A/V output jacks on your camcorder or other video  
VIDEO 2 INPUT  
equipment.  
3 MENU  
Press to display the Menu. Press again to exit from the Menu. For details, see  
“Using the Menus” on page 77.  
Vv B b  
Press Vv B b to move the TV’s on-screen cursor.  
4
5
Press to select an item in the TV’s Menu.  
6
Press to display the Memory Stick Menu. For details, see “Using the Memory  
Stick Viewer” on page 61.  
7 TV/VIDEO  
Press repeatedly to cycle through the video equipment connected to the TV’s  
video inputs.  
8 -VOLUME +  
Press to adjust the volume.  
9 -CHANNEL+  
Press to scan through channels. To scan quickly through channels, press and  
hold down either CHANNEL button.  
0 PRO STD/DUO  
Memory Stick insertion slot. For details, see “Inserting and Removing a Memory  
Stick” on page 64.  
qa Memory Stick LED  
When lit, indicates that the Memory Stick is being read. (Do not remove the  
Memory Stick when the indicator is lit.)  
qs POWER LED  
Lights when the TV is turned on.  
qd TIMER LED  
When lit, indicates one of the timers is set. When the timer is set, this LED will  
remain lit even if the TV is turned off. For details, see page 92. If the LED blinks  
continuously, this may indicate the TV needs service (see “Contacting Sony” on  
page 97).  
qf Infrared Receiver (IR)  
Receives IR signals from the TV’s remote control.  
Press to turn on and off the TV.  
qg POWER  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
Rear Panel  
1
2
qa  
3
4
5
q;  
9
6
7
8
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Jack  
Description  
1 VHF/UHF  
2 S VIDEO IN 1/3  
RF input that connects to your VHF/UHF antenna or cable box.  
Connects to the S VIDEO OUT jack of your VCR or other video equipment that has  
S VIDEO. S VIDEO provides better picture quality than either composite video (3)  
or VHF/UHF (1) connections.  
3 VIDEO IN 1/3/4  
VIDEO/L(MONO)  
-AUDIO-R  
Connect to the composite A/V output jacks on your VCR or other video  
component. A fourth component A/V input jack (VIDEO 2) is located on the front  
panel of the TV. This video connection provides better picture quality than the  
VHF/UHF (1) connection.  
4 MONITOR OUT  
Lets you record the program you are watching to a VCR. When two VCRs are  
connected, you can use the TV as a monitor for tape-to-tape editing (not available  
with digital channels or with 480i, 480p, 720p, or 1080i when the input is set to  
VIDEO 5, 6, or 7).  
5 AUDIO OUT (VAR/FIX)  
Connects to the left and right audio input jacks of your audio or video equipment.  
You can use these outputs to listen to your TV’s audio through your stereo system.  
6 HD/DVD IN 5/6  
Connect to your DVD player’s or digital set-top box’s component video (Y, PB, PR)  
and audio (L/R) jacks. Component video provides better picture quality than 1,  
2, or 3).  
(1080i/720p/480p/480i)  
7 CONTROL S  
Allows the TV to receive (IN) and send (OUT) remote control signals to other Sony  
infrared-controlled audio or video equipment that has the CONTROL S function.  
IN/OUT  
8 HDMI  
HDMI (High-Definition Multimedia Interface) provides an uncompressed, all-  
digital audio/video interface between this TV and any HDMI-equipped  
audio/video component, such as a set-top box, DVD player, and A/V receiver.  
HDMI supports enhanced, or high-definition video, plus two-channel digital audio.  
(VIDEO 7 IN)  
9 DIGITAL AUDIO OPTICAL Connect to the optical audio input of an audio component that is Dolby* Digital and  
OUTPUT  
PCM compatible.  
(DOLBY DIGITAL PCM)  
0 CableCARD Slot  
Provides cable subscribers with access to digitally encrypted cable channels —  
without the need for a set-top box — that will enable you to receive not only  
standard definition but also high definition television. The CableCARD, which is  
provided by your cable TV company, is inserted into this slot. After the service is  
activated with your cable TV company, the card replaces the need for a separate set-  
top box. Check with your cable TV company about CableCARD service details,  
limitations, pricing, and availability. For more information, see page 41.  
qa Cable  
RF input that connects to your cable signal.  
* Dolby and the double-D symbol are trademarks of Dolby Laboratories.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                       
Basic Connections: Connecting a Cable or Antenna  
The way in which you will connect your TV varies, depending on  
how your home receives a signal (cable, cable box, antenna) and  
whether or not you plan to connect a VCR.  
If You Are Connecting  
Cable or Antenna Only  
See Page  
17  
No cable box or VCR  
Cable and Antenna Only  
No cable box or VCR  
Cable Box and Cable Only  
18  
19  
Cable box unscrambles only some  
channels (usually premium channels)  
No VCR  
Cable Box Only  
20  
Cable box unscrambles all channels  
No VCR  
If you are connecting a VCR  
See the connections described on pages 23 and 24.  
About Using CableCARD  
If you are planning to use a separate cable box for digital cable TV services, you may be able  
to receive programming using this TV with the CableCARD instead — except in the following  
circumstances:  
Your cable TV company does not provide CableCARD service in your viewing area.  
You want to access your cable company’s interactive or advanced features (such as video-  
on-demand or, in some cases, pay-per-view). At this time, these services require a  
bidirectional link, which are only available through the use of a separate set-top box.  
CableCARD is currently a unidirectional device only, and cannot provide these advanced  
services.  
Check with your cable TV company for CableCARD service details, limitations, pricing, and  
availability, all of which are determined by your cable TV company — not Sony. For  
information on installing and activating CableCARD, see “Using CableCARD” on page 41.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Cable or Antenna  
Only  
For best results, use one of the following connections if you are connecting a  
cable or an antenna and you:  
Do not need a cable box to unscramble channels. (If you have a  
cable box, see pages 19-20.)  
Do not intend to connect a VCR. (If you have a VCR, see pages 23  
and 24.)  
The connection you choose depends on the cable type you have in  
your home, as described below.  
75-ohm coaxial cable (usually found in newer homes)  
Cable Type  
Connect As Shown  
VHF Only or  
combined  
VHF/UHF  
TV  
75-ohm  
coaxial  
cable  
VHF/UHF  
TV  
Cable  
75-ohm  
coaxial  
cable  
CABLE  
300-ohm twin lead cable (usually found in older homes)  
Cable Type  
Connect As Shown  
VHF Only or  
UHF Only or  
combined  
300-ohm twin  
lead cable  
TV  
VHF/UHF  
VHF/UHF  
Antenna connector  
(not supplied)  
75-ohm coaxial and 300-ohm twin lead cable (found in some homes)  
Cable Type  
Connect As Shown  
75-ohm  
coaxial cable  
VHF and UHF  
TV  
VHF/UHF  
U/V mixer  
(not supplied)  
300-ohm twin  
lead cable  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Cable and Antenna  
Only  
For best results, use this connection if you:  
Have a cable and an antenna.  
(This is convenient if you are using a separate rooftop antenna to  
receive additional channels that are not provided by your cable  
company.)  
Do not have a cable box or VCR. (If you have a cable box, see  
pages 19 to 20. If you have a VCR, see pages 23 and 24.)  
Cable Type  
Connect As Shown  
Cable TV (CATV)  
and Antenna  
Antenna cable  
CATV cable  
Notes on Using This Connection  
To Do This ...  
Do This ...  
Switch the TV’s input  
between the cable and  
antenna  
Press ANT to switch back and forth between the TV’s VHF/UHF and CABLE  
inputs.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Cable Box and  
Cable Only  
For best results, use this connection if:  
Your cable company scrambles some channels, such as premium  
channels (which requires you to use a cable box), but does not  
scramble all channels.  
Before connecting a cable  
box, see About Using  
CableCARD” on page 16.  
With this connection you can:  
Use the TV remote control to change channels coming through  
the cable box to the TV’s VHF/UHF input jack. (You must first  
program the remote control for your specific cable box; see  
“Programming the Remote Control” on page 49.)  
Use the TV remote control to change channels coming directly  
into the TV’s CABLE input. (The TV’s tuner provides a better  
signal than the cable box.)  
Splitter  
Coaxial cable  
CATV cable  
Coaxial cable  
Coaxial cable  
Cable box  
TV  
VHF/UHF  
CABLE  
Notes on Using This Connection  
To Do This ...  
Do This ...  
Use the cable box  
Tune the TV to the channel the cable box is set to (usually channel 3 or 4)  
and then use the cable box to switch channels.  
Set up the TV remote control Program the remote control. See “Programming the Remote Control” on  
to operate the cable box pages 49-50.  
Activate the remote control to Press SAT/CABLE FUNCTION.  
operate the cable box  
Switch the TV’s input  
between the cable box and  
cable  
Press ANT to switch back and forth between the TV’s VHF/UHF (scrambled  
channels) and CABLE (unscrambled) inputs.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Cable Box Only  
For best results, use this connection if:  
Your cable company scrambles all channels, which requires you  
to use a cable box.  
Before connecting a cable  
box, see About Using  
CableCARD” on page 16.  
You do not have a VCR. (If you have a VCR, see pages 23 and 24.)  
With this connection you can:  
Use the TV remote control to change channels coming through  
the cable box to the TV’s VHF/UHF jack. (You must first  
program the remote control for your specific cable box.)  
To connect the cable box  
1
2
Connect the CATV cable to the cable box’s input jack.  
Use a coaxial cable to connect the cable box’s output jack to the  
TV’s VHF/UHF jack.  
CATV  
cable  
TV  
Coaxial cable  
VHF/UHF  
1
2
IN  
OUT  
Cable box  
3
Run Auto Program, as described in “Setting Up the Channel List”  
on page 43.  
Notes on Using This Connection  
To Do This ...  
Do This ...  
Use the cable box  
Tune the TV to the channel the cable box is set to (usually channel 3 or 4)  
and then use the cable box to switch channels.  
Set up the TV remote control Program the remote control. See “Programming the Remote Control” on  
to operate the cable box pages 49.  
Activate the remote control to Press SAT/CABLE FUNCTION.  
operate the cable box  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Connecting Optional Equipment  
Use the directions in this section to connect the following optional  
equipment:  
If You Are Connecting  
VCR and Cable  
See Page  
24  
28  
30  
32  
VCR and Cable Box  
Satellite Receiver  
Satellite Receiver and VCR  
DVD Player with Component Video  
Connectors  
Connectors  
34  
Camcorder  
35  
36  
37  
38  
Audio Receiver  
DVI-Equipped Device  
HDMI-Equipped Device  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Making Video  
Connections  
Your TV includes several types of video inputs. When connecting  
your TV, use the outputs that are available on your components that  
provide the best video performance, as described below.  
Best Video Performance  
HDMI (High-Definition  
Multimedia Interface)  
Component video  
S VIDEO  
Composite video  
RF/Coaxial  
Good Video Performance  
About Using  
S VIDEO  
If the optional equipment you are connecting has an S VIDEO  
jack (shown at left), you can use an S VIDEO cable for  
improved picture quality (compared to an A/V cable).  
Because S VIDEO carries only the video signal, you also need  
to connect audio cables for sound, as shown below.  
Example of an S VIDEO Connection  
TV  
S VIDEO  
cable  
Equipment with S VIDEO  
Cables are often  
color-coded to connectors.  
Connect red to red,  
white to white, etc.  
Audio cable  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
VCR and Cable  
For best results, use this connection if:  
Your cable company does not require you to use a cable box.  
To connect the VCR and cable  
1
2
Connect the CATV cable to the VCR’s VHF/UHF input jack.  
Using  
S VIDEO jacks?  
See page 22.  
Use a coaxial cable to connect the VCR’s VHF/UHF output jack  
to the TV’s CABLE jack.  
3
4
Use an A/V cable to connect the VCR’s A/V output jacks to the  
TV’s A/V input jacks.  
Run Auto Program, as described in “Setting Up the Channel List”  
on page 43.  
TV  
Coaxial cable  
VCR  
CATV cable  
Cables are often  
color-coded to connectors.  
Connect red to red,  
A/V cable  
white to white, etc.  
Notes on Using This Connection  
To Do This ...  
Do This ...  
Watch the VCR  
Press TV/VIDEO repeatedly to select the VCR input (VIDEO 1 in the  
illustration).  
Watch cable channels  
Press TV/VIDEO repeatedly to select the cable input (CABLE in the  
illustration).  
Set up the TV remote control If you have a non-Sony VCR, you must program the remote control. See  
to operate the VCR  
“Programming the Remote Control” on pages 49-50.  
Activate the TV remote  
Press VCR/DVD FUNCTION.  
control to operate the VCR  
Control VCR functions with  
the TV remote control  
See “Operating a VCR” on page 59.  
Label video inputs to easily  
identify equipment connected  
to the TV  
See the instructions for setting up Video Labels on page 90.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
VCR and Cable Box  
For best results, use this connection if:  
Your cable company scrambles some channels, such as premium  
channels (which requires you to use a cable box), but does not  
Before connecting a cable  
box, see About Using  
CableCARD” on page 16.  
With this connection you can:  
Use the TV remote control to change channels coming through  
the cable box. (You must first program the remote control for  
your specific cable box; see “Programming the Remote Control”  
on page 49.)  
Use the TV remote control to change channels coming directly  
into the TV’s CABLE jack. (The TV’s tuner provides a better  
signal than the cable box.)  
Record channels coming through the cable box and channels  
coming directly into the TV.  
To connect a VCR and cable box, you need:  
A splitter, which is a small, inexpensive device that you can  
purchase at your local electronics store.  
Four coaxial cables.  
Two A/V cables or two S VIDEO cable with audio cables.  
To connect the VCR and cable box  
1
2
Connect the CATV cable to the single (input) jack of the splitter.  
Use a coaxial cable to connect one of the splitter’s two output  
jacks to the TV’s CABLE jack.  
3
5
6
7
Use a coaxial cable to connect the splitter’s other output jack to  
the cable box’s input jack.  
Use a coaxial cable to connect the cable box’s output jack to the  
VCR’s RF input jack.  
Use an A/V cable to connect the cable box’s A/V output jacks to  
the TV’s A/V input jacks.  
Using  
S VIDEO jacks?  
See page 22.  
Use an A/V cable to connect the VCR’s A/V output jacks to the  
TV’s A/V input jacks.  
Run Auto Program, as described in “Setting Up the Channel List”  
on page 43.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
TV  
Coaxial  
cable  
Splitter  
(not supplied)  
CATV  
cable  
Coaxial  
cable  
Cable box  
Cables are often  
color-coded to connectors.  
Connect red to red,  
white to white, etc.  
Coaxial  
cable  
A/V cable  
VCR  
A/V cable  
Notes on Using This Connection  
To Do This ...  
Do This ...  
Watch cable (unscrambled)  
channels  
Press TV/VIDEO repeatedly to select the cable input (CABLE in the  
illustration).  
Watch cable box (scrambled) Press TV/VIDEO repeatedly to select the cable box input (VIDEO 3 in the  
channels  
illustration). Use the cable box to change channels.  
Watch the VCR  
Press TV/VIDEO repeatedly to select the VCR input (VIDEO 1 in the  
illustration).  
Set up the TV remote control If you have a non-Sony VCR, you must program the remote control. See  
to operate the cable box or  
VCR  
“Programming the Remote Control” on pages 49-50.  
Activate the remote control to For the cable box, press SAT/CABLE FUNCTION. For the VCR, press VCR/DVD  
operate the cable box or VCR FUNCTION.  
Control specific cable box and See “Operating a Cable Box” on page 60 and “Operating a VCR” on page 59.  
VCR functions with the TV  
remote control  
Label video inputs to easily  
identify equipment connected  
to the TV  
See the instructions for setting up Video Labels on page 90.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Two VCRs for Tape  
Editing  
Connecting two VCRs lets you record from one VCR to the other. By  
connecting them as shown below, you can view (monitor) what is  
being recorded.  
Using  
S VIDEO jacks?  
See page 22.  
To connect two VCRs for tape editing  
1
Use an A/V cable to connect the playback VCR’s A/V output  
jacks to the TV’s A/V input jacks.  
2
Use an A/V cable to connect the recording VCR’s A/V input  
jacks to the TV’s MONITOR OUT jacks.  
TV  
Cables are often  
color-coded to connectors.  
Connect red to red,  
white to white, etc.  
Recording VCR  
Playback VCR  
A/V cable  
A/V cable  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Notes on Using This Connection  
To Do This ...  
Do This ...  
View (monitor) what is being Press TV/VIDEO repeatedly to select the VCR input (VIDEO 1 in the  
recorded illustration above).  
Set up the TV remote control If you have a non-Sony VCR, you must program the remote control. See  
to operate the VCR(s)  
“Programming the Remote Control” on pages 49-50.  
Activate the TV remote  
Press VCR/DVD FUNCTION.  
control to operate the VCR(s)  
Control VCR functions with  
the TV remote control  
See “Operating a VCR” on page 59.  
Label video inputs to easily  
identify equipment connected  
to the TV  
See the instructions for setting up Video Labels on page 90.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Satellite Receiver  
To connect a satellite receiver  
1
2
3
4
Connect the satellite antenna cable to the satellite receiver’s  
satellite input jack.  
Using  
S VIDEO jacks?  
See page 22.  
Use an A/V cable to connect the satellite receiver’s A/V output  
jacks to the TV’s A/V input jacks.  
Connect a CATV cable from your cable or antenna to the TV’s  
CABLE jack.  
Run Auto Program, as described in “Setting Up the Channel List”  
on page 43.  
TV  
CATV cable  
Satellite receiver  
Satellite antenna  
cable  
Cables are often  
color-coded to connectors.  
Connect red to red,  
white to white, etc.  
A/V cable  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Notes on Using This Connection  
To Do This ...  
Do This ...  
Watch the satellite receiver  
Press TV/VIDEO repeatedly to select the satellite receiver input  
(VIDEO 1 in the illustration).  
Set up the TV remote control to operate the If you have a non-Sony satellite receiver, you must program  
satellite receiver  
the remote control. See “Programming the Remote Control”  
on pages 49-50.  
Activate the TV remote control to operate  
the satellite receiver  
Press SAT/CABLE FUNCTION.  
Control satellite receiver functions with the See “Operating a Satellite Receiver” on page 59.  
TV remote control  
Label video inputs to easily identify  
equipment connected to the TV  
See the instructions for setting up Video Labels on page 90.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Satellite Receiver  
and VCR  
To connect a satellite receiver and VCR  
1
Connect the CATV cable to the single (input) jack of the splitter.  
Use a coaxial cable to connect one of the splitter’s two output  
jacks to the TV’s CABLE jack.  
3
4
5
6
7
8
Use a coaxial cable to connect the splitter’s other output jack to  
the satellite receiver’s VHF/UHF input jack.  
Using  
S VIDEO jacks?  
See page 22.  
Connect the satellite antenna cable to the satellite receiver’s  
satellite input jack.  
Use a coaxial cable to connect the satellite receiver’s VHF/UHF  
output jack to the VCR’s VHF/UHF input jack.  
Use an A/V cable to connect the satellite receiver’s A/V output  
jacks to the TV’s A/V input jacks.  
Use an A/V cable to connect the VCR’s A/V output jacks to the  
TV’s A/V input jacks.  
Run Auto Program, as described in “Setting Up the Channel List”  
on page 43.  
CATV  
cable  
Splitter  
(not supplied)  
Satellite antenna  
cable  
Coaxial  
cable  
TV  
Coaxial  
cable  
Satellite receiver  
Cables are often  
color-coded to connectors.  
Connect red to red,  
white to white, etc.  
Coaxial  
cable  
A/V cable  
VCR  
A/V cable  
7
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Notes on Using This Connection  
To Do This ...  
Do This ...  
Watch the satellite receiver  
Press TV/VIDEO repeatedly to select the VCR input (VIDEO 3 in the  
illustration).  
Watch the VCR  
Press TV/VIDEO repeatedly to select the input to which the VCR is connected  
(VIDEO 1 in the illustration).  
Set up the TV remote control If you have a non-Sony VCR or satellite receiver, you must program the  
to operate the satellite  
receiver or VCR  
remote control. See “Programming the Remote Control” on pages 49-50.  
Activate the TV remote  
For the satellite receiver, press SAT/CABLE FUNCTION. For the VCR, press  
control to operate the satellite VCR/DVD FUNCTION.  
receiver or VCR  
Control satellite receiver and See “Operating a Satellite Receiver” on page 59 and “Operating a VCR” on  
VCR functions with the TV  
remote control  
page 59.  
Label video inputs to easily  
identify equipment connected  
to the TV  
See the instructions for setting up Video Labels on page 90.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD Player with  
Component  
For best results, use this connection if your DVD player has  
component video (Y, PB, PR) jacks.  
Video Connectors  
To connect a DVD player with component video connectors  
1
Use three separate component video cables to connect the DVD  
player’s Y, PB and PR jacks to the Y, PB and PR jacks (VIDEO 5) on  
the TV.  
The Y, PB and PR jacks on your DVD player are sometimes labeled Y,  
CB and CR, or Y, B-Y and R-Y. If so, connect the cables to like colors.  
2
Use an audio cable to connect the DVD players audio output  
jacks to the TV’s VIDEO 5 audio input jacks.  
Component video cables  
TV  
DVD player  
Cables are often  
color-coded to connectors.  
Connect red to red,  
white to white, etc.  
Audio cable  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Notes on Using This Connection  
To Do This ...  
Do This ...  
Watch the DVD player  
Press TV/VIDEO repeatedly to select the DVD input (VIDEO 5 in the  
illustration).  
Set up the TV remote control If you have a non-Sony DVD player, you must program the remote control.  
to operate the DVD player  
See “Programming the Remote Control” on pages 49-50.  
Activate the TV remote  
control to operate the DVD  
player  
Press VCR/DVD FUNCTION.  
Control DVD functions with See “Operating a DVD Player” on page 60.  
the TV remote control  
Label video inputs to easily  
identify equipment connected  
to the TV  
See the instructions for setting up Video Labels on page 90.  
You cannot record the signal from any equipment connected into the Y, PB,  
PR jacks.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD Player with  
S VIDEO and Audio  
Connectors  
Use this connection if your DVD player does not have component  
video (Y, PB, PR) jacks.  
To connect a DVD player with A/V connectors  
1
Use an audio cable to connect the DVD player’s audio output  
jacks to the TV’s audio input jacks.  
2
Use an S VIDEO cable to connect the DVD player’s S VIDEO  
jack to the TV’s S VIDEO jack.  
TV  
S VIDEO  
cable  
DVD player  
Cables are often  
color-coded to connectors.  
Connect red to red,  
white to white, etc.  
Audio cable  
Notes on Using This Connection  
To Do This ...  
Do This ...  
Watch the DVD player  
Press TV/VIDEO repeatedly to select the DVD input (VIDEO 1 in the  
illustration).  
Set up the TV remote control If you have a non-Sony DVD player, you must program the remote control.  
to operate the DVD player  
See “Programming the Remote Control” on pages 49-50.  
Activate the TV remote  
control to operate the DVD  
player  
Press VCR/DVD FUNCTION.  
Control DVD functions with See “Operating a DVD Player” on page 60.  
the TV remote control  
Label video inputs to easily  
identify equipment connected  
to the TV  
See the instructions for setting up Video Labels on page 90.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Camcorder  
For easy connection of a camcorder, the TV has front A/V input jacks.  
If you prefer, however, you can connect the camcorder to the TV’s  
rear A/V input jacks.  
Using  
S VIDEO jacks?  
See page 22.  
To connect a camcorder  
1
Use A/V cables to connect the camcorder’s A/V output jacks to  
the TV’s A/V input jacks.  
TV  
VIDEO 2 INPUT  
L(MNO) – AUDO – R  
VIDEO  
S VIDEO  
Cables are often  
color-coded to connectors.  
Connect red to red,  
white to white, etc.  
A/V cable  
Camcorder  
To A/V output  
If you have a mono camcorder, connect its audio output jack to the  
TV’s L MONO audio jack.  
Notes on Using This Connection  
To Do This ...  
Do This ...  
Watch the camcorder  
Press TV/VIDEO repeatedly to select the camcorder input (VIDEO 2 in the  
illustration).  
Label video inputs to easily  
identify equipment connected  
to the TV  
See the instructions for setting up Video Labels on page 90.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Audio Receiver  
For improved sound quality, you may want to play the TV’s audio  
through your stereo system.  
To connect an audio system  
1
Use an audio cable to connect the TV’s audio output jacks to the  
audio receiver’s line input jacks.  
TV  
Cables are often  
color-coded to connectors.  
Connect red to red,  
white to white.  
Audio cable  
To line input  
Receiver  
2
3
Using the TV’s Audio Menu, set the Speaker option to Off. Then set  
the Audio Out option to Fixed or Variable, depending on how you want  
to control the volume. For details, see “Using the Audio Menu”  
on page 80.  
Turn on the audio receiver, and then set the receiver’s line input  
to the jack into which you connected the TV.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
DVI-Equipped  
Device  
If you have a device, such as an HDTV receiver, that has DVI (Digital  
Video Interface) output, use the following connection.  
To connect a device that has DVI OUT:  
1
Use an HDMI-to-DVI cable to connect the device’s DVI OUT jack  
to the TV’s HDMI IN jack.  
You can purchase HDMI cables (or cable adapters) at your local electronics  
store.  
2
Use an audio cable to connect the device’s audio output jacks to  
the TV’s HDMI analog audio input jacks.  
TV  
HDMI-to-DVI cable  
Audio cable  
HDTV Receiver  
Note on Using This Connection  
To Do This ...  
Do This ...  
Watch the DVI device  
Press TV/VIDEO repeatedly to select the VIDEO 7 input.  
Label video inputs to easily  
identify equipment connected  
to the TV  
See the instructions for setting up Video Labels on page 90.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
HDMI-Equipped  
Device  
If you have a device, such as an HDTV receiver, that has a High-  
Definition Multimedia Interface (HDMI), use the following  
connection.  
To connect a device that has HDMI OUT:  
1
Use the HDMI cable that came with your device to connect the  
device’s HDMI OUT jack to the TV’s HDMI IN jack.  
HDMI cables transmit both audio and video signals. (Separate audio cables  
are not necessary.) You can purchase HDMI cables at your local electronics  
store.  
TV  
HDMI cable  
HDTV Receiver  
Note on Using This Connection  
To Do This ...  
Do This ...  
Watch the HDMI device  
Press TV/VIDEO repeatedly to select the VIDEO 7 input.  
See the instructions for setting up Video Labels on page 90.  
Label video inputs to easily  
identify equipment connected  
to the TV  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Connecting a Device with an Optical IN Connector  
You can use the TV’s DIGITAL AUDIO OPTICAL output jack to  
connect an audio device that is Dolby Digital and PCM compatible,  
such as an audio amplifier.  
Using an optical cable, connect the TV’s DIGITAL AUDIO  
OPTICAL output jack to the device’s audio optical input jack.  
TV  
Optical audio cable  
Audio Amplifier  
Because all equipment does not output digital audio, you should also  
connect the TV’s analog audio output jacks to the amplifier’s analog audio  
input jacks, as described on page 36.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Using the CONTROL S Feature  
CONTROL S allows you to control your system and other Sony  
equipment with one remote control. In addition to allowing you to  
control multiple devices with one remote control, the CONTROL S  
feature allows you to always point your remote control at your TV,  
instead of having to point it at the other equipment, which might be  
hidden or out of direct line of sight.  
Use CONTROL S IN to send signals to the TV.  
Use CONTROL S OUT to send signals to connected equipment.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Using CableCARD  
CableCARD provides cable subscribers with access to digitally  
encrypted cable channels — without the need for a set-top box — that  
will enable you to receive not only standard definition but also high  
definition television. The CableCARD, which is provided by your  
cable TV company, is inserted into the TV’s rear panel CableCARD  
slot. After the service is activated with your cable TV company, the  
card replaces the need for a separate set-top box.  
About Using CableCARD  
If you are planning to use a separate cable box for digital cable TV services, you may be able  
to receive programming using this TV with the CableCARD instead — except in the following  
circumstances:  
Your cable TV company does not provide CableCARD service in your viewing area.  
You want to access your cable company’s interactive or advanced features (such as video-  
on-demand or, in some cases, pay-per-view). At this time, these services require a  
bidirectional link, which are only available through the use of a separate set-top box.  
CableCARD is currently a unidirectional device only, and cannot provide these advanced  
services.  
Check with your cable TV company for CableCARD service details, limitations, pricing, and  
availability, all of which are determined by your cable TV company — not Sony.  
Activating  
CableCARD Service  
Before you can use CableCARD service, you need to insert the  
CableCARD (supplied by your cable TV company) and activate the  
service, as described below:  
1
Insert the CableCARD into the TV’s CableCARD slot.  
Top of CableCARD is on same  
side as indicator on slot  
CAUTION: Inserting the CableCARD incorrectly may result in permanent  
damage to the card and the TV.  
!
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
2
3
Gently push the card into the slot until it locks into place.  
Turn on the TV. After 1-2 minutes, the CableCARD setup screen is  
displayed. This screen includes information your cable TV  
company will request before they can activate your service.  
z
You can also access  
information about your  
CableCARD in the Applications  
Menu (see page 93).  
4
5
Follow the displayed instructions: Phone your cable company. A  
representative will guide you through the activation process.  
After your CableCARD is activated, your cable TV company will  
download the service information, including the channel list, to  
the CableCARD.  
After the CableCARD has acquired channels from your cable TV  
company, the TV tunes to the lowest available channel.  
Removing the  
CableCARD  
In the event you want to cancel your service, contact your cable TV  
company.  
Once the CableCARD is removed, your TV will no longer decrypt digital  
cable TV programming services that require CableCARD.  
1
Push the eject button on the TV’s CableCARD slot to release the  
card.  
Eject button  
2
Pull the CableCARD straight out of the slot to remove it.  
To install a different CableCARD, follow the instructions in  
“Activating CableCARD Service” on page 41.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Setting Up the Channel List  
After you finish connecting the TV, you need to run the Initial Setup  
feature, which automatically creates a list of available analog and  
digital channels and lets you correct tilt and vertical correction  
settings. The Initial Setup screens appear when you turn on your TV  
for the first time after hooking it up.  
Using Initial Setup  
To run Initial Setup  
1
Press POWER to turn on the TV.  
The Initial Setup screen appears.  
Using the remote control, move the highlight to the desired  
language, then press  
to select that language. The Tilt  
Correction screen appears.  
z
For more details on using  
2
3
Press B b to correct any tilt of the picture. You can choose a  
correction between +7 and -7. When finished, press  
Tilt Correction and Vertical  
Correction, see pages 89-90.  
.
The Vertical Correction screen appears. Press V v to make a  
vertical correction to the picture. You can choose a correction  
between +5 and -5. When finished, press  
.
z
To exit the Tilt Correction  
and Vertical Correction screens,  
press the MENU button.  
4
The next screen instructs you to connect your cable/antenna.  
Check that you’ve connected your signal source correctly.  
To start Auto Program, highlight Yes and then press  
.
z
If you are using a  
Auto Program automatically creates a list of receivable analog  
and digital channels. Auto Program may take 50 minutes or more  
to complete. A progress bar is displayed while the channel list is  
being created.  
CableCARD, Auto Program is  
disabled for the CABLE input.  
When Auto Program is finished, the lowest numbered channel is  
displayed.  
To run Auto Program again at a later time  
Use the Auto Program feature as described on page 84.  
To add individual digital channels  
Use the Digital Channel feature as described on page 84.  
To reset the TV to factory settings  
1
2
3
Press POWER to turn on the TV.  
Hold down RESET on the remote control.  
Press TV POWER on the TV. (The TV will turn itself off, then back  
on.)  
4
Release RESET.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Remote Control  
Overview  
This chapter describes how to set up, program, and use the TV’s  
remote control.  
Topic  
Page  
45  
Inserting Batteries  
Button Descriptions  
Programming the Remote Control  
46  
49  
Inserting Batteries  
1
Remove the battery cover from the remote control.  
2
Insert two size AA (R6) batteries (supplied) by matching the e  
and E terminals on the batteries to the diagram inside the battery  
compartment.  
3
Replace the battery cover.  
2
1
Remove the batteries to avoid damage from possible battery leakage  
whenever you anticipate that the remote control will not be used for an  
extended period.  
Handle the remote control with care.  
Avoid dropping it, getting it wet, placing it in direct sunlight, near a heater,  
or where the humidity is high.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Button Descriptions  
qd  
qf  
1
2
3
4
5
6
7
8
qg  
qh  
qj  
qk  
ql  
9
w;  
wa  
q;  
qa  
ws  
wd  
qs  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Button  
Description  
1
MUTING  
Press to mute the sound. Press again or press VOL+ to restore the sound.  
SYSTEM OFF  
Press to turn off all Sony brand audio/video equipment at once. (May not function  
with older Sony equipment. Does not function with DVD/VCR combination unit.)  
2
TV/VCR/DVD  
Press to change the VHF/UHF output of the VCR (or DVD/VCR combination unit).  
3
Transport  
Buttons  
m Rewind  
N Play  
z Record (press together with N)  
x Stop  
M Fast forward  
X Pause  
4
5
6
JUMP  
ANT  
Press to jump back and forth between two channels. The TV alternates between the  
current channel and the last channel that was selected.  
Press to switch between the sources connected to the TV’s VHF/UHF and CABLE  
inputs.  
SLEEP  
Press repeatedly until the TV displays the time in minutes (15, 30, 45, 60, or 90) that  
you want the TV to remain on before shutting off automatically. To cancel press until  
Sleep Off appears. While the Sleep feature is set, press once to display the remaining  
time.  
7
8
PICTURE MODE Press repeatedly to cycle through the available video picture modes: Vivid, Standard,  
Movie, Pro. Also available in the Video Menu. For details, see “Selecting Video Options”  
on page 78.  
DRC MODE  
Press repeatedly to cycle through the available Digital Reality Creation modes:  
Interlaced, Progressive, CineMotion. Also available in the Video Menu. For details, see  
“Selecting Video Options” on pages 78-79.  
MEMORY STICK Press to display the Memory Stick Menu. For details, see “Using the Memory Stick  
9
0
Viewer” on page 61. Also available in the Applications Menu (page 92).  
RESET  
Press to reset the settings to the factory defaults. See pages 43, 79, and 81. Also used to  
clear Favorite Channels (see page 58).  
qa  
qs  
VOL +/-  
Press to adjust the volume.  
CODE SET  
Press to program the remote control to operate non-Sony video equipment. For details,  
see “Programming the Remote Control” on page 49.  
qd  
POWER  
Buttons  
VCR/DVD: Press to turn on and off the VCR or DVD player.  
SAT/CABLE: Press to turn on and off the satellite receiver or cable box.  
TV: Press to turn on and off the TV.  
qf  
FUNCTION  
Buttons  
The indicator lights up momentarily when pressed to show which equipment the  
remote control is operating:  
VCR/DVD: Press to have the remote control operate the VCR or DVD player.  
SAT/CABLE: Press to have the remote control operate the satellite receiver or cable box.  
TV: Press to have the remote control operate the TV.  
TV/SAT  
When the remote control is set to operate the satellite receiver, press to switch between  
the satellite receiver’s TV and SAT (satellite) inputs.  
qg  
When the remote control is set to operate the TV, press repeatedly to step through the  
Audio Effect options. Also available in the Audio Menu. For details, see page 80.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                                     
Button  
qh  
Description  
TV/VIDEO  
DISPLAY  
Press repeatedly to cycle through the TV’s video inputs.  
qj  
Press once to display the current channel number, current time, and channel label (if  
set) and other information. Press again to turn Display off.  
qk  
ql  
SCREEN MODE Press to toggle between the Screen Mode options. For details on using Screen Mode,  
see pages 55-57. Also available in the Screen Menu (pages 82-83).  
0 - 9  
ENTER  
Press 0 - 9 to select a channel; the channel changes after 3 seconds. Press ENTER to  
change channels immediately. Use the button with 0-9 and ENTER buttons to select  
digital channels (for example, 2.1). For details on selecting digital channels, see  
page 52.  
w;  
wa  
GUIDE  
Press to display the program guide of your satellite program provider.  
Press Vv B b to move the on-screen cursor. To select an item, press  
.
When no menus are displayed, pressing displays the Favorite Channels screen.  
(For more information about Favorite Channels, see page 58.)  
ws  
wd  
MENU  
CH +/-  
Press to display the Menu. Press again to exit from the Menu. For details, see “Using  
the Menus” on page 77.  
Press to scan through channels. To scan quickly through channels, press and hold  
down either CH button.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Programming the Remote Control  
If you have video equipment other than Sony brand (or if you have a  
Sony DVD/VCR combination unit) that you want to control with the  
TV’s remote control, use the following procedure to program the  
remote control.  
The equipment must have infrared (IR) remote capability in order to be used  
with the remote control.  
1
Turn to the list of “Manufacturer’s Codes” on page 50, and find  
the three-digit code number for the manufacturer of your  
equipment. (If more than one code number is listed, use the  
number listed first.)  
2
3
4
Press CODE SET.  
Press the VCR/DVD FUNCTION or SAT/CABLE FUNCTION button.  
Using the 0-9 buttons, enter the three-digit manufacturer’s code  
number.  
5
Press the ENTER button.  
You must do step 5 within 10 seconds of step 4, or you must redo  
steps 2 through 5.  
6
To check if the code number works, aim the TV’s remote control  
at the equipment and press the POWER button that corresponds  
with that equipment. If it responds, you are done. If not, try using  
another code listed for that manufacturer.  
Notes  
If more than one code number is listed, try entering them one by  
one until you come to the correct code for your equipment.  
If you enter a new code number, the code number you previously  
entered at that setting is erased.  
In some cases, you may not be able to operate your equipment  
with the supplied remote control. In such cases, use the  
equipment’s own remote control.  
Whenever you remove the batteries to replace them, the code  
numbers may revert to the factory setting and must be  
reprogrammed.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Manufacturer’s Codes  
VCRs  
DVD Players  
Manufacturer  
Realistic  
Code  
Manufacturer  
Sony  
Apex  
General Electric  
Hitachi  
JVC  
Magnavox  
Mitsubishi  
Oritron  
Panasonic  
Philips  
Code  
751  
762  
755  
758  
756  
757  
761  
759  
753  
757  
752  
755  
758  
754  
760  
Manufacturer  
Sony  
Admiral  
(M. Ward)  
Aiwa  
Audio Dynamic 314, 337  
Broksonic  
Canon  
Code  
301, 302, 303  
327  
309, 330, 328,  
335, 324, 338  
314  
322, 313, 321  
330, 335  
312, 313, 321,  
335, 323, 324,  
325, 326  
Sansui  
Samsung  
Sanyo  
Scott  
338, 344  
319, 317  
309, 308  
332  
302, 332  
315  
304, 338, 309  
341, 312, 309  
314, 336, 337  
304  
319, 320, 316,  
317, 318, 341  
330, 335  
338  
Citizen  
Craig  
Sharp  
327, 328  
338, 327  
Signature 2000  
(M. Ward)  
SV2000  
Sylvania  
Symphonic  
Tashiro  
Tatung  
Teac  
Technics  
Toshiba  
Wards  
Criterion  
Curtis Mathes  
Daewoo  
DBX  
Dimensia  
Emerson  
Pioneer  
338  
RCA/Proscan  
Samsung  
Toshiba  
308, 309, 338, 310  
338  
332  
314, 336, 337  
314, 336, 338, 337  
309, 308  
312, 311  
327, 328, 335,  
331, 332  
314, 330, 336, 337  
331  
Zenith  
Cable Boxes  
Manufacturer  
Sony  
Fisher  
Funai  
Code  
230  
222, 223, 224,  
225, 226  
201, 202, 203,  
204, 205, 206,  
207, 208, 218  
227, 228, 229  
219, 220, 221  
214, 215  
General Electric 329, 304, 309  
Go Video  
Goldstar  
Hitachi  
Instant Replay  
JC Penney  
322, 339, 340  
332  
306, 304, 305, 338  
309, 308  
Hamlin/Regal  
Yamaha  
Zenith  
Jerrold/G. I./  
Motorola  
309, 305, 304,  
330, 314, 336, 337  
314, 336, 337,  
345, 346, 347  
314, 336, 332, 337  
332, 305, 330,  
335, 338  
308, 309, 310  
314, 336, 337  
332  
Laserdisc Players  
Manufacturer  
Sony  
Panasonic  
Pioneer  
Oak  
Panasonic  
Pioneer  
Scientific Atlanta 209, 210, 211  
Tocom  
Zenith  
Code  
701  
704, 710  
702  
JVC  
Kenwood  
LXI (Sears)  
216, 217  
212, 213  
DVD/VCR Combination Units  
Manufacturer  
Sony  
Broksonic  
JVC  
Panasonic  
Samsung  
Toshiba  
Magnavox  
Marantz  
Marta  
Memorex  
Minolta  
Mitsubishi/  
MGA  
Multitech  
NEC  
Olympic  
Optimus  
Orion  
Code  
601  
605  
604  
609  
Satellite Receivers  
Manufacturer  
Sony  
Dish Network  
Echostar  
General Electric 802  
Hitachi  
Hughes  
Mitsubishi  
Panasonic  
RCA/  
Code  
801  
810  
309, 335  
305, 304  
323, 324, 325, 326  
810  
603  
602  
325, 338, 321  
314, 336, 337  
309, 308  
327  
317  
805  
804  
809  
803  
802, 808  
Panasonic  
Pentax  
308, 309, 306, 307  
305, 304  
PROSCAN  
Toshiba  
806, 807  
Philco  
308, 309  
Philips  
Pioneer  
Quasar  
RCA/  
PROSCAN  
308, 309, 310  
308  
308, 309, 306  
304, 305, 308,  
309, 311, 312, 313,  
310, 329  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Using the Features  
Overview  
Topic  
Page  
Watching TV  
Using the Program Guide  
53  
Using Screen Mode (30/34 models only)  
Using Screen Mode (32/36 models only)  
Using Favorite Channels  
55  
57  
58  
Using Other Equipment with Your TV Remote Control  
59  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Watching TV  
To Do This ...  
Do This ...  
z
For a complete list of all  
Activate the remote control to  
operate the TV  
Press TV FUNCTION  
the functions of the remote  
control, see pages 45-50.  
Turn on/off the TV  
Press TV POWER  
Tune directly to a channel  
To tune to analog channels, press 0-9 and  
then ENTER.  
For digital subchannels, press 0-9,  
,
press 0-9 again, and then ENTER.  
For example, to select subchannel 21.13,  
press 2+1+ +1+3, and then press ENTER.  
You can also select channels using the  
program guide. See pages 53 for  
details.  
Adjust the volume  
Mute the sound  
Press VOL +/-  
Press MUTING (press again to unmute)  
Press JUMP  
Alternate back and forth  
between two channels  
The TV alternates between the current  
channel and the last channel tuned.  
Display the current channel  
Press DISPLAY once to display the channel  
number (and other information) number, current time, and channel label  
(if set). Press DISPLAY again to turn Display  
off.  
Switch the TV’s input to the  
VCR, DVD player, or other  
connected equipment  
Press TV/VIDEO repeatedly to cycle through  
the video equipment connected to the  
TV’s video inputs.  
Change video and audio  
Press MENU to display the Menu. For  
options, customize the TV’s  
details, see “Using the Menus” on  
setup, set parental controls, and page 77.  
more  
Switch the TV’s input between Press ANT to alternate between sources  
sources connected to the TV’s  
connected to the TV’s VHF/UHF and  
VHF/UHF and CABLE inputs CABLE inputs.  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                       
Using the Program Guide  
The program guide lets you review program information and select  
both analog and digital channels.  
The Program Guide cannot be displayed when the TV is tuned to one of the  
video inputs or if the Channel Fix option is set to anything other than Off  
(see page 84).  
GUIDE  
To display the program guide:  
Press GUIDE on the TV’s remote control. The program guide appears,  
with the currently selected program showing in the background.  
Program title and  
description, time  
remaining, rating  
information, closed-  
caption availability,  
format, resolution (if  
digital), aspect ratio  
Channel number, call  
letters, Auto SAP (if  
available  
Selectable channel list  
Program information in the guide is provided by the broadcasters. As a  
result, it may sometimes include only the channel number, without a  
program title or description.  
To Do This ...  
Do This ...  
Press V v  
Press  
Scroll through the channel list  
Select the currently displayed  
channel and exit the guide  
.
Display additional options  
Press b. See “Using Additional Program  
Guide Options” on page 54.  
Exit the Guide (without  
changing channels)  
Press GUIDE  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Using Additional  
Program Guide  
Options  
Press b while in the program guide’s channel list to display the  
following options, which allow you to customize the settings of the  
program on the currently tuned channel.  
Option  
Description  
Alternate Video  
(when  
available)  
Each program has a main video stream (the video that you  
see when the channel is first tuned), and may have  
alternate video streams. This option allows you to switch  
among these alternate video streams.  
Alternate Audio Each program has a main audio stream (the audio that you  
(when  
available)  
hear when the channel is first tuned). This option allows  
you to switch among these alternate audio streams (e.g.,  
for different languages).  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Using Screen Mode (30/34 models only)  
The Screen Mode feature lets you change the picture size for both  
standard-definition (480i/480p) and high-definition (720p/1080i)  
sources.  
z
You can also access the Screen  
Mode settings in the Screen Menu.  
For details, see page 82.  
Press SCREEN MODE repeatedly to toggle through the following  
Screen Mode settings.  
Using Screen Mode with Standard Definition (480i/480p) Sources  
Example  
Description  
Wide Zoom enlarges the center portion of the  
picture proportionately. The left and right  
edges of the picture are stretched to fill the  
16:9 screen.  
SCREEN  
Wide Zoom  
m
Normal displays the 4:3 picture in its original  
size. Bars are shown to fill the 16:9 screen.  
SCREEN  
SCREEN  
SCREEN  
Normal  
m
Full stretches the 4:3 picture horizontally, to fill  
the 16:9 screen.  
Full  
m
Zoom enlarges the 4:3 picture proportionately  
to fill the 16:9 screen. Some clipping may  
occur. Zoom is useful for watching Letterbox  
movies.  
Zoom  
When you change channels or inputs, the Screen Mode settings revert  
to the 4:3 Default setting in the Screen Menu. To retain the current  
Screen Mode setting as channels and inputs are changed, set 4:3 Default  
to Off. For details, see page 82.  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Using Screen Mode with High-Definition (720p/1080i) Sources  
Example  
Description  
Full displays the picture at its original size.  
SCREEN  
If the source is a 16:9 high-definition  
(720p/1080i) signal, the picture fills the  
screen.  
Full (native 16:9)  
If the source is a 4:3 standard-definition  
signal that has been upconverted, bars are  
shown to fill the 16:9 screen.  
Full (upconverted 4:3)  
m
Zoom enlarges the picture proportionately,  
both vertically and horizontally. Some  
clipping may occur.  
SCREEN  
Zoom  
m
Horizontal Expand stretches the picture  
SCREEN  
horizontally. Some clipping may occur.  
Horizontal Expand  
m
Vertical Expand stretches the picture  
SCREEN  
vertically. Some clipping may occur.  
Vertical Expand  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Using Screen Mode (32/36 models only)  
The Screen Mode feature is useful when a 480i signal has been  
upconverted to a 720p or 1080i signal, which results in undesirable  
“black bars” appearing on all four sides of the picture. Using the  
Screen Mode feature, you can enlarge these pictures, minimizing the  
size of the black bars.  
Using Screen Mode with High Definition (720p/1080i) Sources  
Example  
Description  
Full displays a 480i signal that has been  
upconverted to 720p or 1080i with black bars  
visible at left, right, top, and bottom sides.  
SCREEN  
Full  
m
Zoom enlarges the picture, minimizing the size  
of the black bars.  
SCREEN  
SCREEN  
SCREEN  
Zoom  
m
Horizontal Expand stretches the picture  
horizontally. Some clipping may occur.  
Horizontal Expand  
m
Vertical Expand stretches the picture vertically.  
Some clipping may occur.  
Vertical Expand  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Using Favorite Channels  
The Favorite Channels feature lets you select programs from a list of  
up to 16 favorite channels that you specify. You can create a list using  
the Favorite Channel option in the Channel Menu, or by using the  
Add to Favorites feature in the Favorite Channels guide.  
Using the Channel  
Menu  
1
3
4
Press MENU to display the Menu.  
Press V or v to highlight the Channel icon and press  
.
Press  
to select Favorite Channels.  
Use the 0-9 and ENTER buttons to enter the channel number that  
you want to assign to the Favorite Channel number. Press  
select that channel as a Favorite Channel.  
to  
z
For details on using the  
Channel Menu, see page 84.  
To enter digital channel numbers in step 4, use the 0-9, , and ENTER  
buttons.  
5
To add more channels to your favorites list, repeat step 4.  
To clear a Favorite Channel, press V or v to highlight the channel  
you want to clear. Press  
and then press RESET.  
6
Press MENU to exit the Menu.  
Using the Favorite  
Channels Guide  
1
2
During normal viewing (with no menus on screen), press  
The Favorite Channels list appears.  
.
Press V or v to highlight the channel you want to watch.  
To add the current channel to the list of Favorite Channels,  
highlight Add to Favorites and press  
.
To change your Favorite Channels list, highlight Edit Favorites and  
press  
Press  
.
3
to select the channel you want to watch.  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Using Other Equipment with Your TV Remote Control  
All Equipment  
To Do This ...  
Do This ...  
Switch the TV’s input to the  
VCR, DVD player, or other  
connected equipment  
Press TV/VIDEO repeatedly to cycle through  
the video equipment connected to the  
TV’s video inputs.  
Set up the TV remote control to You must program the remote control the  
operate non-Sony equipment  
(and Sony DVD/VCR  
combination unit)  
first time you use it. See “Programming  
the Remote Control” on page 49.  
Operating a VCR  
To Do This ...  
Press  
Activate the remote control VCR/DVD FUNCTION  
to operate the VCR  
Turn on/off  
Change channels  
Adjust tracking  
Record  
VCR/DVD POWER  
CH +/- (using tuner)  
CH +/- (during tape playback)  
N and z simultaneously  
Play  
Stop  
N
x
Fast forward  
Rewind the tape  
Pause  
M
m
X
Search the picture forward M or m during playback  
or backward  
(release to resume normal playback)  
Operating a  
Satellite Receiver  
To Do This ...  
Press  
Activate the remote control SAT/CABLE FUNCTION  
to operate the satellite  
receiver  
Turn on/off  
Select a channel  
Change channels  
SAT/CABLE POWER  
0-9, ENTER  
CH +/-  
Back to previous channel  
Display channel number  
Display SAT Guide  
Display SAT Menu  
Move highlight (cursor)  
JUMP  
DISPLAY  
GUIDE  
MENU  
V v B b  
Select item  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Operating a Cable  
Box  
To Do This ...  
Press  
Activate the remote control SAT/CABLE FUNCTION  
to operate the cable box  
Turn on/off  
Select a channel  
SAT/CABLE POWER  
0-9, ENTER  
CH +/-  
Change channels  
Back to previous channel  
JUMP  
Operating a DVD  
Player  
To Do This ...  
Press  
Activate the remote control VCR/DVD FUNCTION  
to operate the DVD  
Turn on/off  
Play  
VCR/DVD POWER  
N
Stop  
x
Pause  
X
Step through different  
tracks of the disc  
M to step forward or m to step backward  
Step through different  
chapters of a video disc  
CH+ to step forward or CH- to step backward  
Select tracks directly  
0-9, B b (to move cursor), ENTER  
Display the DVD menu  
Move highlight (cursor)  
MENU  
V v B b  
SELECT  
Select item  
Operating a  
DVD/VCR  
Combination Unit  
To Do This ...  
Press  
Activate the remote control VCR/DVD FUNCTION  
to operate the DVD/VCR  
Turn on/off  
VCR/DVD POWER  
TV/VCR/DVD  
z
When the VCR is not  
Switch between the DVD  
player and VCR  
playing, TV/VCR/DVD switches  
between the DVD player and  
the VCR’s tuner.  
Display the DVD menu  
MENU  
N
x
Play  
Stop  
Pause  
X
Search the picture forward M or m during playback  
or backward  
Move highlight (cursor)  
and select (DVD)  
V v B b  
Record (VCR)  
N and z simultaneously  
Change channels (VCR)  
Adjust tracking (VCR)  
CH +/- or 0-9, ENTER (using tuner)  
CH +/- (during tape playback)  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Using the Memory Stick Viewer  
About Memory Stick  
Memory Stick (sold separately) is a compact, portable, and versatile  
Integrated Circuit recording medium with a data capacity that makes  
it perfect for portable applications, such as digital photography.  
Memory Stick is specially designed for sharing digital data among  
Memory Stick compatible products such as digital cameras and  
digital video cameras. Because it is removable, Memory Stick can also  
be used for external data storage.  
The Memory Stick Viewer on your TV allows you to view files that  
are stored on Memory Stick media. You can view:  
Movies (MPEG1 files)  
You can also play slide show background music using MP3 files (or  
m3u playlists) stored on your Memory Stick.  
For more information about handling Memory Stick media, see  
“Notes on Using Memory Stick Media” on page 75.  
Features  
With the Memory Stick Viewer, you can:  
View photo (JPEG) and movie (MPEG1) files in a thumbnail  
index or Slide Show  
Set customized Slide Show options, including transitions and  
background audio  
Pan, zoom, and rotate photos  
Mark photos and set quantities of prints to be output when the  
Memory Stick is inserted into your photo printer (not supplied)  
Lock (protect) or delete files on the Memory Stick  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Memory Stick  
Compatibility  
This television is compatible with the following Sony brand Memory  
Stick media types:  
Memory Stick Media  
Memory Stick Duo and PRO Duo Media (without the Memory  
Stick adaptor)  
The Memory Stick slot on your TV has been designed to accommodate  
standard and compact versions of Memory Stick. It is not necessary to use  
an adapter for Memory Stick Duo and Memory Stick PRO Duo. If you use an  
adapter it may damage the adapter and Memory Stick slot.  
Memory Stick Media with Memory Select Function  
Memory Stick PRO Media  
About Memory Stick PRO Media  
Memory Stick PRO media features vary by and are dependent upon  
the design of host hardware devices. Memory Stick PRO in this  
television has been tested to support up to 1 GB media capacity and  
does not support high-speed transfer, MagicGate copyright  
protection technology, or access control security features.  
Memory Stick  
Functionality  
Sony cannot guarantee or assure the Memory Stick functionality on  
this television in the following cases:  
You are using non-Sony brand Memory Stick media.  
You are using video or audio clips that have been processed on a  
computer.  
You are using files that were obtained from the Internet or from a  
printed film processing center.  
The Memory Stick has been formatted on a personal computer.  
Sony recommends that you back up all data stored on Memory Stick  
media to avoid potential data loss. In the above two cases, in order to  
avoid potential data corruption that may occur, be sure to back up  
data prior to use with the TV’s Memory Stick Viewer. Sony cannot  
accept responsibility in the event that data recorded to Memory Stick  
media is lost or damaged. For certain non-Sony brand Memory Stick  
media, you can view images, but you cannot rotate, delete or  
protect/unprotect images on the television. An error message will  
occur if you attempt any of these operations. This is a result of the  
unique file directory structure on these particular flash memory  
media and is not a malfunction of the television.  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
File Compatibility  
The Memory Stick Viewer is compatible with JPEG images taken with  
*
Sony digital still cameras and MPEG1 movies taken with Sony  
digital cameras and camcorders. In order to be viewable in the  
Memory Stick Viewer, the files must have the following file name  
extensions:  
File Type  
Supported File Name Extensions  
JPEG  
.jpg  
.jpeg  
MPEG1  
.mpg  
.mpeg  
Trademark  
Information  
Memory Stick, Memory Stick Duo, Memory Stick PRO, Memory Stick  
PRO Duo, and MagicGate are trademarks of Sony Corporation.  
*Some variations of MPEG1 movies may not play back correctly.  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Inserting and Removing a Memory Stick  
Inserting a  
Memory Stick  
The Memory Stick slot on your TV has been designed to accommodate  
standard and compact versions of Memory Stick. It is not necessary to use  
an adapter for Memory Stick Duo and Memory Stick PRO Duo. If you use an  
adapter it may damage the adapter and Memory Stick slot.  
1
Locate the Memory Stick slot (see page 12) and insert the  
Memory Stick into the Memory Stick slot as illustrated below.  
When inserted properly, it should slide in with little resistance  
and click into place.  
STD/DUO  
VIDEO  
2
INPUT  
+
VOLUME CHANNEL  
_
TV/VIDEO  
L(MONO) – AUDIO – R  
VIDEO  
S VIDEO  
MENU  
STD/DUO  
Be sure to insert the Memory Stick in the correct direction. If the Memory  
Stick is forced in the wrong way, it may become damaged.  
Insert only Memory Stick media into the Memory Stick slot. Attempting to  
insert other objects into the slot may damage the TV.  
To remove the Memory Stick, see “Removing a Memory Stick” on  
page 65.  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Removing a  
To remove a Memory Stick  
Memory Stick  
1
Check that the Memory Stick indicator is off. (When the light is  
on, this indicates that the TV is reading data from the Memory  
Stick.)  
Removing the Memory Stick while a file is being accessed (when the  
Memory Stick LED on the TV’s front panel is lit) may damage the Memory  
Stick or its contents.  
2
Push the Memory Stick gently into the slot, and then release it.  
The Memory Stick media is ejected.  
Do not pull out the Memory Stick without first pushing it in; otherwise, the  
TV’s locking mechanism may become damaged.  
3
Pull the Memory Stick completely out of the slot.  
To protect small children from injury from Memory Stick Media, remove all  
Memory Stick media from the TV’s Memory Stick slot and store it in a safe  
location when it is not in use.  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Using the Memory Stick Index  
Turn on the TV and insert a Memory Stick that contains the photo or  
movie files you want to view. For details, see page 64.  
MEMORY STICK  
If the Memory Stick Index does not appear, press the MEMORY STICK button  
on the remote control.  
The Memory Stick Index appears, which displays thumbnail images  
of the files stored on the Memory Stick.  
Information about the  
highlighted photo or movie  
Highlighted thumbnail  
Thumbnails of photos and  
movies  
Memory Stick Menu bar  
About the Icons on the Thumbnail Images  
Indicates the thumbnail is a movie (MPEG1) file instead of a photo  
(JPEG) file.  
Indicates the thumbnail is locked. Locked files cannot be changed  
or deleted. For details, see “Protect” on page 69.  
Indicates that the photo is marked to be printed.  
Indicates that the photo has an associated voice memo.  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Using the Memory  
Stick Index  
The following describes how to use the Memory Stick Index.  
To Do This ...  
Do This ...  
Move the highlight  
to a photo, voice  
memo ( ), or  
Press V v B b.  
movie (  
)
thumbnail  
Display the  
Press  
. For details, see “Viewing Photos” on  
highlighted photo,  
voice memo, or  
movie file full  
screen  
page 68 and “Playing Movies” on page 71.  
Display the next  
page of thumbnails  
1 Press v to select V.  
2 Press v to display the next page of thumbnails.  
Display the  
previous or next  
page of thumbnails  
1 Press v to select V.  
2 Press B to select  
.
3 To go to the previous page, press V.  
To go to the next page, press v.  
Use the Memory  
Stick Menu bar to  
access additional  
options  
1 Press v to select V.  
2 Press B or b to select Slide Show, Contents, or  
Memory Stick.  
3 Press V or v to select the option you want to  
change.  
For details on these options, see “Memory Stick  
Index Menu Bar Options” on page 73.  
Move the highlight  
from the Memory  
Stick Menu bar back  
to the thumbnails  
1 Press B or b to select V.  
2 Press V to return to the currently displayed  
thumbnails, or v to display the next page of  
thumbnails.  
Exit Memory Stick  
Viewer  
Press the MEMORY STICK button on the remote  
control.  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Viewing Photos  
When you select a photo from the Memory Stick Index (described on  
page 66), it displays as shown below, with the following controls.  
Information about  
selected photo  
Selected photo  
Previous/next buttons  
Photo Menu bar  
JPEGs captured using a digital video camera may appear to display motion  
in full screen. This is a result of the way digital video cameras record still  
images, and is not a result of a malfunction with the TV.  
Photo Controls  
To Do This ...  
Do This ...  
Display the next or  
previous file on the  
Memory Stick  
Highlight the  
Then press B to go to the previous file, or b to  
go to the next file.  
(Previous/Next) button.  
z
When the Menu is hidden,  
press B or b to go to the  
previous or next photo.  
Hide the Photo Menu bar,  
displaying only the photo  
With the highlight in the Photo Menu bar, press  
v.  
Display the hidden Photo  
Menu bar  
Press V.  
Play the JPEG voice memo Highlight B (Play) and then press  
files only) pause the voice memo, highlight X (Pause) and  
then press  
Highlight Index in the Photo Menu bar and  
press  
. To  
(
.
Display the Memory Stick  
Index again  
.
For details on the Memory Stick Index, see  
page 67.  
Access additional options  
in the Photo Menu bar  
See “Photo Menu Bar Options” on page 69.  
Exit Memory Stick Viewer Press the MEMORY STICK button on the remote  
control.  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Photo Menu  
Bar Options  
The Photo Menu bar lets you access additional photo viewing  
options.  
To access the Photo Menu bar  
1
2
Press B or b to select Index, Slide Show, View, or File.  
Press V or v to select the desired option.  
Option  
Description  
Index  
Displays the Memory Stick Index, with the highlight on the  
thumbnail of the currently displayed photo. For details, see  
“Using the Memory Stick Index” on page 66.  
Slide Show  
View  
Displays the Slide Show Menu. For details, see “Slide Show  
Menu Options” on page 73.  
Rotate  
Allows you to rotate the photo in 90 degree  
increments clockwise or counterclockwise. For  
details, see “Using Rotate” on page 70.  
Zoom/Pan  
Protect  
Allows you to magnify and pan across the  
photo. For details, see “Using Zoom and Pan”  
on page 70.  
z
JPEG files that are protected  
File  
Allows you to the protect the JPEG file from  
any changes. When a JPEG file is protected, it  
cannot be rotated or deleted. Select On or Off.  
are indicated by the Lock  
icon.  
Print Quantity Allows you to indicate the number of prints to  
make of the specific photo when the Memory  
Stick is inserted into a compatible photo  
printer (not supplied).  
z
The Print Quantity feature is  
also known as DPOF (Digital  
Print Order Format).  
Delete  
Deletes the JPEG file from the Memory  
Stick.You cannot delete a JPEG file that has  
been protected (or if the Memory Stick is  
locked).  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Using Zoom  
and Pan  
To Zoom and Pan a photo  
1
2
3
In the Photo Menu bar, highlight View.  
Highlight Zoom/Pan and press  
.
Specify the zoom center point by pressing B b V v ; then press  
to set the center.  
The Zoom and Pan controls are displayed.  
To Do This ...  
Do This ...  
Zoom in (increase magnification)  
or out (decrease magnification)  
Highlight Zoom and press V to zoom in or v to zoom out.  
For help on using Zoom, press  
.
Pan (move the photo left,  
right, up, down)  
(You can use Pan only when the photo is magnified using Zoom.)  
Highlight Pan and press  
. Then press B b V v to pan around the  
photo.  
To stop using Pan, press  
.
.
Exit the Zoom/Pan controls  
Exit Memory Stick Viewer  
Highlight Exit and press  
Press the MEMORY STICK button on the remote control.  
Using Rotate  
To Rotate a photo  
1
2
3
In the Photo Menu bar, highlight View.  
Highlight Rotate.  
To rotate clockwise, highlight Clockwise and press  
.
To rotate counterclockwise, highlight Counterclockwise and press  
.
The photo is rotated 90 degrees each time you press  
.
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Playing Movies  
When you select a movie from the Memory Stick Index (described on  
page 66), it displays as shown below, with the following controls.  
Information about  
selected movie  
Selected movie  
Enlarge button  
Play/pause button  
Previous/next buttons  
Movie Menu bar  
MPEG movies recorded in VX Fine mode with Sony digital cameras cannot  
be played back with the Memory Stick Viewer.  
Movie Controls  
To Do This ...  
Do This ...  
z
The quality of the movie  
Enlarge the movie  
window  
Highlight Enlarge, and then press  
display the movie controls again, press  
When the movie ends, the movie controls are  
displayed again.  
. To  
when enlarged depends on the  
resolution of the MPEG1 file. See  
your camera’s instruction manual  
for details.  
.
Play the movie with the Highlight B (Play) and then press  
movie controls displayed  
.
Pause the movie  
Highlight X (Pause) and then press  
.
Highlight the (Previous/Next) button.  
Then press B to go to the previous file, or b to  
go to the next file.  
Display the previous or  
next file on the Memory  
Stick  
Hide the Movie Menu  
bar, displaying only the  
movie  
With the highlight in the Movie Menu bar, press  
v.  
Display the hidden  
Movie Menu bar  
Press V.  
Access additional options See “Movie Menu Bar Options” on page 72.  
in the Movie Menu bar  
Exit Memory Stick  
Viewer  
Press the MEMORY STICK button on the remote  
control.  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Movie Menu  
Bar Options  
To access the Movie Menu bar  
1
2
Highlight Index in the Movie Menu bar.  
Option  
Description  
z
Index  
Displays the Memory Stick Index, with the highlight on the  
thumbnail of the currently displayed movie.  
MPEG1 files that are  
protected are indicated by the  
Lock  
icon.  
Slide Show Displays the Slide Show Menu. For details, see “Slide Show  
Menu Options” on page 73.  
File  
Protect  
Allows you to the protect the MPEG1 file from  
any changes. When an MPEG1 file is  
protected, it cannot be deleted. Select On or Off.  
Delete  
Deletes the MPEG1 file from the Memory  
Stick.You cannot delete an MPEG1 file that has  
been protected (or if the Memory Stick is  
locked).  
72  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Memory Stick Index Menu Bar Options  
Slide Show Menu  
Options  
The Slide Show Menu includes the following options:  
Option  
Start  
Description  
Starts the Slide Show.  
z
The Slide Show Menu is the  
Music  
Allows you to select background audio to play during the  
Slide Show.  
same whether you select it from  
the Memory Stick Index  
(page 66), Photo (page 68), or  
Movie (page 71) Menus.  
Off  
No additional background audio is played  
during the Slide Show. Audio that is associated  
with the JPEG or MPEG1 files will play.  
Play Memory  
Stick  
Plays all MP3 files on the Memory Stick. The  
Piano MP3 file and any MP3 file playlists are  
not played.  
Piano (built-in) Plays the MP3 file stored in the TV’s internal  
memory.  
(List of MP3  
Files and  
Playlists)  
Displays a list of all MP3 files and MP3 file  
playlists found at the top level (root) of the  
Memory Stick. To show additional MP3 files  
stored in other folders on the Memory Stick,  
select Complete List.  
z
When you select Complete  
List, it may take a moment to  
display the list of all MP3 files.  
Complete  
List  
Displays a list of all available MP3 files.  
Transition  
Effect  
Allows you to select an effect to be used when advancing to  
the next file in the Slide Show.  
z
Some JPEG files may take  
longer to display than others,  
which may make it seem longer  
than the interval you selected for  
Slide Advance.  
Slide Advance Allows you to specify when to advance to the next slide.  
Fast  
Slide advances after about 3 seconds.  
Slide advances after about 6 seconds.  
Slide advances after about 12 seconds.  
Slide advances only after you press B or b.  
Medium  
Slow  
Manual  
File  
Information  
Determines whether file information is shown when the file is  
displayed full screen. Select On or Off.  
You can also display file  
information using the  
DISPLAY button on the remote  
control.  
Repeat  
On  
Off  
Slide Show continuously loops.  
Slide Show plays once through all files and  
ends.  
73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Contents Menu  
Options  
The Contents Menu includes the following options:  
Option  
Description  
Select Folder  
Allows you to select different folders to view in the  
Memory Stick Viewer.  
Digital Camera  
Folders  
Selects all folders within the directories  
defined by the DCF rules used by Sony  
digital cameras (see page 75). JPEG and  
MPEG1 files in those directories are  
recognized even if they do not conform  
to the DCF file naming rules.  
Select a Folder  
Allows you to access individual folders  
on the Memory Stick.  
File Order  
Allows you to change the order in which the Memory  
Stick files are displayed.  
Date Order  
Displays files in chronological order by  
modification date.  
z
The Rotate function does not  
change the file’s modification  
date.  
Date Order Reverse Displays files in reverse chronological  
order by modification date.  
Alphabetical  
Displays files in alphabetical order by  
filename.  
Filter  
Allows you to selectively display specific file types  
within the selected folder.  
Show Photos and Displays all readable files.  
Movies  
Show Photos Only Displays only photo (JPEG) files.  
Show Movies Only Displays only movie (MPEG1) files.  
Show All Print  
Marks  
Displays all files that are marked for  
printing. For details, see “Print  
Quantity” on page 69.  
Memory Stick  
Menu  
The Memory Stick Menu displays the current status of the Memory  
Stick, including total capacity, used capacity, and free capacity.  
74  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Notes on Using Memory Stick Media  
About DCF File  
Names  
Most Sony brand digital still and video cameras automatically record  
still photo and movie files using DCF compliant directory and file  
names.  
If you selected the Digital Camera Folders option, as described on page 74,  
you might want to have your digital camera’s instruction manual  
handy in order to check how files and directories are organized for  
your specific model of digital camera.  
DCF stands for “Design Rules for Camera File Systems,” which are  
specifications established by the Japan Electronic Industry  
Development Association (JEIDA).  
75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Memory Stick  
Precautions  
When using Memory Stick media, follow these precautions:  
To avoid permanent damage to still image data, do not turn  
off the TV or remove Memory Stick media from the insertion  
slot while data is being read (as indicated by the Memory  
Stick indicator light being on).  
Avoid touching the terminal of Memory Stick media or  
bringing it into contact with a metal object.  
Do not drop, bend, or submit Memory Stick media to external  
shock.  
Do not disassemble or modify Memory Stick media.  
Avoid getting liquid on Memory Stick media.  
Apply labels only within the designated label area.  
Label Area  
To avoid permanent damage to still image data, do not use or  
store Memory Stick media in a location subject to:  
High temperature (such as near a heater or inside a hot  
car)  
High humidity  
Direct sunlight  
Corrosive substances  
Magnetic fields  
Excessive dust  
Static electricity or electric noise  
Electric surges  
Store and carry Memory Stick media in its original case to  
ensure protection of stored data.  
Save a backup of stored data.  
76  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Using the Menus  
Overview  
The Menu gives you access to the following features:  
Menu  
Description  
Page  
The Video Menu allows you to make adjustments to  
your picture settings. It also allows you to customize  
the Picture Mode based on the type of program you are  
viewing, select Advanced Video options, and more.  
78  
The Audio Menu Offers enhanced audio options such 80  
as listening to second audio programming (SAP) or  
customizing the Effect of the sound on your TV.  
The Screen Menu allows you to make 82  
30/34 models only  
Screen Mode adjustments and make changes to the  
screen’s vertical center and size.  
The Screen Menu allows you to make 83  
32/36 models only  
Screen Mode adjustments and select options from the  
Analog 16:9 and Digital 16:9 features.  
z
The Channel Menu allows you to set up a Favorite  
Channel list, run the Auto Program function, label  
channels, and more.  
84  
Press MENU to enter and  
exit Menus.  
The Parental Lock Menu lets you control the viewing of 86  
programs based on their ratings.  
The Setup Menu provides options for setting up your 89  
system, including selecting closed caption modes,  
labeling video inputs, selecting the language and color  
of the on-screen Menus, and more.  
The Applications Menu lets you display the Memory  
Stick Viewer, set on/off Timers, access CableCARD  
and diagnostics information, and more.  
92  
Navigating Through Menus  
To Do This ...  
Press  
Display the Menu  
MENU  
Move through the Menus  
V v B b  
Select an option to change  
Select (confirm) changed setting  
Exit the Menu  
or B  
MENU  
77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
Using the Video Menu  
To access the Video Menu, follow these steps:  
1. Display Menu 2. Highlight 3. Press to select  
To change settings, press V v B b.  
Press to confirm the selection.  
To exit the Menu, press MENU.  
Selecting Video  
Options  
The Video Menu includes the following options:  
Option  
Description  
Mode  
Customized  
picture  
Vivid  
Select for enhanced picture contrast and  
sharpness.  
You can also change the  
Mode setting using the  
PICTURE MODE button on the  
remote control.  
Standard  
Movie  
Pro  
Select for standard picture settings.  
Select to display a softer picture.  
viewing  
Select to display a picture with minimum  
enhancements.  
z
You can alter the Video  
To control how the Mode settings (Vivid, Standard, Movie, Pro) are  
applied to each video input, see Mode Memory on page 79.  
Menu settings (Picture,  
Brightness, Color, etc.) for each  
Mode.  
Picture  
Adjust to increase picture contrast and deepen the color, or  
decrease picture contrast and soften the color.  
Brightness  
Color  
Adjust to brighten or darken the picture.  
Adjust to increase or decrease color intensity.  
Adjust to increase or decrease the green tones.  
Adjust to sharpen or soften the picture.  
Hue  
Sharpness  
Color Temp.  
White  
intensity  
adjustment  
Cool  
Select to give the white colors a blue tint.  
Select to give the white colors a neutral tint.  
Neutral  
Warm  
Select to give the white colors a red tint  
(NTSC-Standard).  
78  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                 
Option  
Description  
ClearEdge VM Sharpens picture definition to give every object a sharp, clean  
Velocity  
edge. Select from High, Medium, Low, Off.  
Modulation  
Advanced  
Video  
Select Program to choose among the Advanced Video options.  
You can also change the  
DRC Mode using the DRC  
MODE button on the remote  
control.  
DRC Mode  
Creates a high-resolution picture with 4x  
density, for high quality sources (i.e., DVD  
player, satellite receiver).  
Interlaced Recommended for moving  
pictures.  
Progressive Recommended for still images and  
text.  
CineMotion Provides an optimized display by  
automatically detecting film  
content and applying a reverse 3/2  
pulldown process. Moving  
pictures will appear clearer and  
more natural-looking.  
Color Axis  
Allows you to control the emphasis of red  
tones.  
Default  
Emphasizes red tones.  
Monitor  
De-emphasizes red tones.  
Mode Memory Allows you to control how the Mode settings  
(Vivid, Standard, Movie, Pro) are applied to TV  
viewing, Memory Stick viewing, and each  
video input. For details about Mode settings,  
see page 78.  
On  
Set to On to customize Mode  
settings for each video input.  
Changing inputs might change the  
Mode setting.  
Off  
Set to Off to apply the same Mode  
settings to all video inputs.  
Changing inputs does not change  
the Mode setting.  
To restore the factory default settings for Video settings:  
Press RESET on the remote control when in the Video Menu.  
79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Using the Audio Menu  
To access the Audio Menu, follow these steps:  
1. Display Menu 2. Highlight 3. Press to select  
To change settings, press V v B b.  
Press to confirm the selection.  
To exit the Menu, press MENU.  
Selecting Audio  
Options  
The Audio Menu includes the following options:  
Option  
Treble  
Description  
Adjust to decrease or increase higher-pitched sounds.  
Adjust to decrease or increase lower-pitched sounds.  
Adjust to emphasize left or right speaker balance.  
Bass  
Balance  
Steady Sound  
Auto  
Off  
Select to stabilize the volume.  
Select to turn off Steady Sound.  
The Steady Sound option is not available (it is grayed out)  
if the Effect option is set to TruSurround or Simulated. To  
use Steady Sound, set Effect to Off.  
You can also change the  
Effect using the button  
on the remote control.  
Effect  
TruSurround Select for surround sound (for stereo programs  
only).  
Simulated  
Off  
Adds a surround-like effect to mono programs.  
Normal stereo or mono reception.  
MTS  
Stereo  
Select for stereo reception when viewing a  
program broadcast in stereo.  
Enjoy stereo,  
bilingual and  
mono programs  
Auto SAP  
Select to automatically switch the TV to second  
audio programs when a signal is received. (If no  
SAP signal is present, the TV remains in Stereo  
mode.)  
Mono  
Select for mono reception. (Use to reduce noise  
during weak stereo broadcasts.)  
MTS is available only with analog programs.  
80  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                             
Option  
Description  
Audio Out  
This option can be set only when the Speaker option is set  
Easy control of to Off.  
volume  
adjustments  
Variable  
The TV’s speakers are turned off, but the  
volume output from your audio system can still  
be controlled by the TV’s remote control.  
Fixed  
The TV’s speakers are turned off and the  
volume output of the TV is fixed. Use your  
audio receiver’s remote control to adjust the  
volume through your audio system.  
Speaker  
On  
Off  
Select to turn on the TV speakers.  
Select to turn off the TV speakers and listen to  
the TV's sound only through your external  
audio system speakers.  
To restore the factory default settings for Treble, Bass, and Balance  
Press RESET on the remote control when in the Audio Menu.  
81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Using the Screen Menu (30/34 models only)  
To access the Screen Menu, follow these steps:  
1. Display Menu  
2. Highlight  
3. Press to select  
To change settings, press V v B b.  
Press to confirm the selection.  
To exit the Menu, press MENU.  
Selecting Screen  
The Screen Menu includes the following options:  
Mode Options  
Option  
Description  
Screen Mode  
Enables you to change the picture size for both standard-  
definition (480i/480p) and high-definition (720p/1080i)  
sources.  
You can also change the  
Screen Mode using the  
SCREEN MODE button on the  
remote control.  
For 480i/480p  
sources  
Select from: Wide Zoom, Normal, Full, Zoom.  
For details, see page 55.  
For 720p/1080i  
sources  
Select from: Full, Zoom, Horizontal Expand,  
Vertical Expand. For details, see page 56.  
In some cases, wide-screen programs will be shown in  
aspect ratios that require the display of bars at the top and  
bottom of your 16:9 screen. For more details, see page 101.  
4:3 Default  
Select the default Screen Mode to use for 4:3 sources.  
To select a Screen Mode to use when channels or inputs are  
changed, select from: Wide Zoom, Normal, Full, Zoom. For  
details, see page 55.  
To continue using the current Screen Mode setting when the  
channel or input is changed, select Off.  
Vertical Center Allows you to move the position of the picture up and down  
in the window. (Available only in Wide Zoom and Zoom  
modes.)  
Press V or v and press  
to choose a correction between  
+15 and -15 (Zoom mode), and +5 and -5 (Wide Zoom  
mode).  
Vertical Size  
Allows you to adjust the vertical size of the picture.  
(Available only in Wide Zoom and Zoom modes.)  
Press V or v and press  
to choose a correction between  
+7 and -7.  
82  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Using the Screen Menu (32/36 models only)  
To access the Screen Menu, follow these steps:  
1. Display Menu  
2. Highlight  
3. Press to select  
To change settings, press V v B b.  
Press to confirm the selection.  
To exit the Menu, press MENU.  
Selecting Screen  
The Screen Menu includes the following options:  
Mode Options  
Option  
Description  
Screen Mode  
Enables you to change the picture size for both  
standard-definition (480i/480p) and high-definition  
(720p/1080i) sources.  
You can also change the  
Screen Mode using the  
SCREEN MODE button on the  
remote control.  
Select from: Full, Normal, Horizontal Expand, Vertical Expand.  
For details, see page 57.  
In some cases, wide-screen programs will be shown in  
aspect ratios that require the display of bars at the  
top and bottom of your 16:9 screen. For more details,  
see page 101.  
z
Analog 16:9  
Provides enhanced picture resolution for widescreen  
(anamorphic) sources, such as selected DVD titles. This  
option is available only when the TV is set to  
VIDEO 1-7.  
To use Analog 16:9 with  
widescreen DVDs, set your DVD  
player to 16:9 aspect ratio.  
(Aspect ratio is the ratio of width  
to height of the screen. 16:9 is  
also referred to as widescreen  
format.)  
On  
To activate manually. Returns to Auto when  
you switch to another video input or  
change channels.  
Auto  
To activate automatically when a 16:9  
signal is received.  
If the Auto setting does not automatically detect the  
16:9 signal from your DVD player, select On to  
manually turn on the 16:9 Enhanced feature.  
z
Digital 16:9  
Allows you to determine the formatting for digital 16:9  
pictures.  
Digital 16:9 is available only  
for digital broadcast sources  
(antenna or cable).  
Pan-n-Scan  
The picture is clipped to fit the 4:3 screen.  
This setting is temporary and will be reset  
when you change channels or video  
inputs, or turn off your TV.  
Letterbox  
The picture is made smaller so that the left  
and right edges fit the 4:3 screen. No  
clipping results, but bars appear at the top  
and bottom of the picture.  
83  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Using the Channel Menu  
To access the Channel Menu, follow these steps:  
1. Display Menu 2. Highlight 3. Press to select  
To change settings, press V v B b.  
Press to confirm the selection.  
To exit the Menu, press MENU.  
Selecting Channel  
The Channel Menu includes the following options:  
Options  
Option  
Description  
Favorite Channels Lets you set up a list of your favorite channels. For  
details, see “Using Favorite Channels” on page 58.  
Channel Fix  
Off  
2-6  
Turns off Channel Fix.  
“Fix” your TV’s channel setting to 2–6  
(VHF/UHF input) and use the cable box  
or satellite receiver to change channels.  
C2-C6  
“Fix” your TV’s channel setting to C2–C6  
(CABLE input) and use the cable box or  
satellite receiver to change channels.  
Video 1  
Add  
Use this setting if you have connected the  
equipment to the A/V input jacks.  
Digital Channels  
Auto Program  
Select to add digital channels.  
z
If you are using a  
Automatically sets up the channel list on the TV for all  
receivable channels.  
Auto Program may take 50 minutes or more to  
complete. A progress bar will display the approximate  
progress of the Auto Program and Digital Channels/Add  
sequences.  
CableCARD, Auto Program is  
disabled for the CABLE input.  
However, you can run Auto  
Program for the VHF/UHF  
input.  
84  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
Option  
Description  
Show/Hide  
Channels  
Allows you to show or hide channels that appear in the  
Program Guide (page 53) and when you use the CH+/-  
buttons to channel surf. Channels that are set to Hidden do  
not appear in the Program Guide or when you use the  
CH+/- buttons.  
z
Channels that you set to  
Hidden can be accessed only  
with the 0-9 buttons.  
1
Press V or v to highlight the channel that you want  
to show or hide.  
To move between the Major and Digital subchannel  
lists, press B or b.  
2
3
To change a channel’s setting to Shown or Hidden,  
press  
.
To show or hide more channels, repeat steps 1 and 2.  
Label Channels  
Allows you to assign labels (such as station call letters) to  
channel numbers.  
1
Press V v to scroll through the channel numbers.  
Then press to select the channel number that  
you want to assign a label.  
2
Press V v to scroll through the label characters (A-Z,  
0-9, etc.). Then press  
character.  
to select the highlighted  
Repeat to add characters to the label.  
3
4
To assign labels to more channels, repeat steps 1-2.  
Press B to return to the Channel Menu, or press  
MENU to exit the Menus.  
85  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Using the Parent Menu  
The Parent Menu allows you to set up the TV to block programs according to their  
content and rating levels.  
To access the Parent Menu, follow these steps:  
1. Display Menu  
2. Highlight  
3. Press to select  
Use the 0-9 buttons on the remote control to  
enter a four-digit password.  
If this is the first time you are creating this password, confirm the password by  
entering it again. (The Parent Menu options appear.)  
To change settings, press V v B b. Press  
to confirm the selection.  
To exit the Menu, press MENU.  
You need your password for any future access into the Parent Menu. If you lose your  
password, see “Lost password” on page 101.  
Selecting Parent  
The Parent Menu includes the following options:  
Menu Options  
Option  
Description  
Parental Lock  
Turn ratings  
on/off and select a  
rating system  
Off  
Parental lock is off. No programs are  
blocked from viewing.  
z
If you are not familiar with  
the Parental Guideline rating  
system, you should select Child,  
Youth, or Y. Adult to help  
simplify the rating selection. To  
set more specific ratings, select  
Custom.  
Child  
Maximum ratings permitted are:  
US: TV-Y, TV-G, G  
Canada: C, G, TV-Y  
Youth  
Maximum ratings permitted are:  
US: TV-PG, PG  
Canada: C8+, PG, 8 ans+, TV-PG  
Y. A d u lt  
(Young Adult)  
Maximum ratings permitted are:  
z
For descriptions of Child,  
US: TV-14, PG-13  
Youth, and Y. Adult ratings,  
see page 87.  
Canada: 14+, 13 ans+, TV-14  
Custom  
Select to set ratings manually.  
US: See page 87 for details.  
Canada: See page 88 for details.  
Change Password For changing your password.  
Select Country  
U.S.A.  
Select to use USA ratings (see page 87).  
Canada  
Select to use Canadian ratings (see  
page 88).  
86  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
US Models:  
Selecting Custom  
Rating Options  
For US models, the Custom Rating Menu includes the following  
options. (For Canadian models, see page 88.)  
Option  
Description  
All children and General Audience.  
Movie Rating  
G
PG  
Parental Guidance suggested.  
z
PG-13  
R
Parental Guidance for children under 13.  
The Content-Based Ratings  
are linked to the level of the  
Age-Based Rating. For example,  
a program with an Age-Based  
Rating of TV-PG V (Violence)  
rating may contain moderate  
violence, while a TV-14 V  
Restricted viewing, parental guidance is  
suggested for children under 17.  
NC-17  
and X  
No one 17 or under allowed.  
TV Rating  
Age-Based Ratings  
Block programs  
by their rating,  
content or both  
TV-Y  
All children.  
(Violence) rating may contain  
more intense violence.  
TV-Y7  
TV-G  
Directed to children age 7 and older.  
General Audience.  
z
TV-PG  
TV-14  
TV-MA  
Parental Guidance suggested.  
Parents Strongly cautioned.  
Mature Audience only.  
To ensure maximum  
blocking capability, set the Age-  
Based Ratings.  
z
If you block unrated TV  
Content-Based Ratings  
programs, be aware that the  
following types of programs  
may be blocked: emergency  
broadcasts, political programs,  
sports, news, public service  
announcements, religious  
programs and weather.  
FV  
Fantasy Violence.  
D
Suggestive Dialogue.  
Strong Language.  
Sexual situations.  
Violence.  
L
S
V
Unrated  
Allow  
Allows programs and movies that are  
broadcast without a rating.  
Block programs  
or movies that  
are broadcast  
without a rating  
Block  
Blocks all programs and movies that are  
broadcast without a rating.  
Viewing Blocked  
Programs  
You can view blocked programs by entering the password. Press the  
ENTER button when tuned to a blocked program, then enter the  
password. This temporarily switches off the Parental Lock. To  
reactivate the Parental Lock settings, turn off the TV. When the TV is  
turned on again, your Parental Lock settings are reactivated.  
87  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Canadian Models:  
Selecting Custom  
Rating Options  
For Canadian models, the Custom Rating Menu includes the  
following options. (For US models, see page 87.)  
Option  
Description  
English Rating  
C
All children.  
C8+  
Children 8 years and older.  
General programming.  
G
PG  
Parental Guidance.  
14+  
Viewers 14 and older.  
18+  
Adult programming.  
French Rating  
U.S.A. Rating  
G
General programming.  
8 ans+  
13 ans+  
16 ans+  
18 ans+  
Not recommended for young children.  
Not recommended for ages under 13.  
Not recommended for ages under 16.  
Programming restricted to adults.  
See “US Models” on page 87 for details.  
Viewing Blocked  
Programs  
You can view blocked programs by entering the password. Press the  
ENTER button when tuned to a blocked program, then enter the  
password. This temporarily switches off the Parental Lock. To  
reactivate the Parental Lock settings, turn off the TV. When the TV is  
turned on again, your Parental Lock settings are reactivated.  
88  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Using the Setup Menu  
To access the Setup Menu, follow these steps:  
1. Display Menu 2. Highlight 3. Press to select  
To change settings, press V v B b.  
Press to confirm the selection.  
To exit the Menu, press MENU.  
Selecting  
Setup Options  
The Setup Menu includes the following options:  
Option  
Description  
Caption Vision  
Allows you to select from several closed caption  
modes (for programs that are broadcast with closed  
caption).  
On  
Caption Vision is turned on.  
Caption Vision is turned off.  
Off  
Program  
Allows you to set basic and advanced  
Caption Vision options. See  
“Programming Caption Vision” on  
page 91.  
Info Banner  
Set to On or Off. When on, displays the program name,  
time remaining and other information (if the  
broadcaster offers this service). Displays when the  
channel is changed or the DISPLAY button is pressed.  
89  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Option  
Description  
Label Video Inputs  
Allows you to identify A/V equipment you connected  
to the TV, such as a VCR, DVD, etc. For example, if  
you have a DVD player connected to the VIDEO 5  
jack, you can select the label DVD for the VIDEO 5  
input. Then when you press the TV/VIDEO button to  
change inputs, the Video Label you assigned to that  
input appears on screen.  
1
Press V or v to highlight the video input (VIDEO  
1-7) to which you want to assign a label. Then  
press  
Press V or v to highlight one of the displayed  
labels. Then press to select the label.  
to select the input.  
2
z
The Skip label is useful for  
inputs that do not have  
equipment connected to  
them.  
You can select from the following labels for each input:  
Video 1-7  
VHS, DVD, Receiver, Satellite, Cable Box, 8mm,  
DTV, Game, LD, Web, Beta, HD, PVR, Skip  
If you select Skip, your TV skips this input when you  
press the TV/VIDEO button.  
z
Normally, Tilt Correction  
Tilt Correction  
Allows you to correct any tilt of the picture.  
and Vertical Correction only  
need to be adjusted the first  
time you turn on the unit and  
after the unit is moved to a  
new location.  
Press B or b to choose a correction between +7 and -7  
and press  
.
Vertical Correction  
Allows you to make a vertical correction to the  
picture.  
Press V or v to choose a correction between +5 and -5  
and press  
.
Language  
Select to display all on-screen Menus in your language  
of choice.  
Menu Color  
Enables you to select a specific color for the on-screen  
menus.  
90  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Programming  
Caption Vision  
If you selected the Program option under Caption Vision (see page 89), you  
can change the following settings:  
Basic  
Allows you to select basic analog (EIA-608) closed caption  
options.  
CC1, CC2,  
CC3, CC4  
Displays a printed version of the dialog or  
sound effects of a program. (Should be set  
to CC1 for most programs.)  
Text1,Text2,  
Text3,Text4  
Displays network/station information  
presented using either half or the whole  
screen (if available). For closed captioning,  
set to CC1.  
Advanced  
Digital CC  
Allows you to select advanced digital (EIA-708) closed  
caption options. Select from the available options.  
Allows you to set digital closed captioning to Basic (digital  
EIA-608) or Advanced (digital EIA-708).  
Advanced  
Settings  
Allows you to make additional settings for digital (EIA-  
708) closed caption options.  
As Broadcast  
Small Text  
Large Text  
Custom ...  
Allows you to customize the following  
settings:  
Character Size  
Character Style  
Character Color  
Edge Color  
Small, Standard, Large  
Style 1-7  
Color 1-8  
Color 1-8  
Edge Type  
None, Raised,  
Depressed, Outline,  
Left shadow,  
Right shadow  
Background Color  
Window Color  
None, Color 1-8  
None, Color 1-8  
Color options can also be set to Solid or  
Translucent.  
91  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Using the Applications Menu  
To access the Applications Menu, follow these steps:  
1. Display Menu  
2. Highlight  
3. Press to select  
To change settings, press V v B b.  
Press to confirm the selection.  
To exit the Menu, press MENU.  
Selecting  
The Applications Menu includes the following options:  
Applications  
Options  
Option  
Description  
Memory Stick  
Displays the Memory Stick Viewer. For details, see  
page 61.  
You can also use the  
MEMORY STICK buttons on  
the remote control or front panel.  
Clock/Timers  
Select to set the clock, set the Sleep timer, and to program  
your TV to turn on and off at two scheduled viewing  
times.  
You can also change the  
Sleep options using the  
SLEEP button on the remote  
control.  
Sleep  
Set the time in minutes (15min,  
30min, 45min, 60min, 90min, or Off)  
that you want the TV to remain on  
before shutting off automatically.  
Timer 1  
Timer 2  
You can use the Timers to program  
the TV to turn on and off and tune  
to a specific channel at two  
scheduled viewing times.  
92  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Option  
Description  
Timer 1 and Timer 2 are not available to be set until you set  
the Current Time.  
z
To go directly to  
programming Timer 1 or 2,  
1
Press V or v to highlight Timer 1 or Timer 2. To set the  
timer, press b.  
press  
instead of  
pressing b.  
2
Press V or v to highlight one of the following options,  
then press  
.
Program  
Select to set the Timer by day,  
time, duration, and channel.  
Off  
Select to turn off the Timer. (Your  
previous settings are saved.)  
z
3
4
If you selected Program in step 2, Press V and v to set  
the day(s), hour, minute, duration, and channel  
To return to the Timer  
Menu after programming one  
of the Timers, press  
number. Press  
or b to confirm each setting and  
move to the next setting. Press B to go back to the  
previous setting.  
Press MENU to exit the Menu. An LED on the front  
panel will light, indicating the timer has been set.  
when the highlight is in the  
channel number field.  
Current Time  
1
2
Press  
Press V and v to set the current time (day, hour, and  
minute). Press or b to confirm each setting and  
move to the next setting. Press B to go back to the  
previous setting.  
to select Current Time.  
z
To return to the Timer  
Menu after setting the  
Current Time, press  
when the highlight is in the  
minute field.  
3
Press MENU to exit the Menu.  
Diagnostics  
CableCARD  
Displays the strength of the terrestrial digital broadcast  
signal, to help you adjust your antenna to optimize signal  
reception.  
This list of selectable CableCARD options will vary,  
depending on your cable service provider.  
93  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Download from Www.Somanuals.com. All Manuals Search And Download.  
Other Information  
Overview  
This chapter includes the following topics:  
Topic  
Page  
96  
Glossary  
Contacting Sony  
Troubleshooting  
Specifications  
Optional Accessories  
Index  
97  
97  
103  
104  
105  
95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Glossary  
analog signal  
A signaling method that uses continuous changes in the amplitude or frequency of an  
electronic transmission to convey information.  
aspect ratio  
Refers to the ratio between the width and height of the screen. 32/36 models have a 4:3  
aspect ratio; 30/34 models have a a 16:9 (widescreen) aspect ratio.  
4:3 aspect ratio  
16:9 aspect ratio  
component video  
Component video is sent through three cables: two color shade (chrominance) signals and one  
brightness (luminance) signal. Component video achieves greater color accuracy than  
composite video or S VIDEO by splitting chrominance into two separate portions.  
composite video  
degauss  
Composite video is sent through a single cable. Composite video combines the color shade  
(chrominance) and brightness (luminance) information into one video signal.  
A process that demagnetizes the metal components in the TV monitor, which eliminates image  
distortion that can result from magnetic charges acquired by the TV’s components. Your TV  
degausses automatically when it is turned on.  
digital television (DTV)  
A new technology for transmitting and receiving broadcast television signals. DTV provides  
clearer resolution and improved sound quality over analog television.  
HDMI (High-Definition  
Multimedia Interface)  
Provides an uncompressed, all-digital audio/video interface between this TV and any HDMI-  
equipped audio/video component, such as a set-top box, DVD player, and A/V receiver. HDMI  
supports enhanced, or high-definition video, plus two-channel digital audio.  
National Television System  
Committee (NTSC)  
A unit of the Federal Communications Commission, Washington, DC, that establishes  
television standards in the United States, such as NTSC Color, the standard used in this TV.  
RF  
Radio Frequency. That part of the frequency spectrum that is used to transmit TV and radio  
signals.  
S VIDEO  
S VIDEO requires a single cable, which carries the brightness (luminance) and color  
(chrominance) signals of the picture separately. S VIDEO provides better resolution than  
composite video, which carries the signals together.  
VHF/UHF  
VHF (Very High Frequency) is the part of the frequency spectrum from 30 to 300 megahertz.  
UHF (Ultra High Frequency) is the part of the frequency spectrum from 300 to 3,000  
megahertz.  
480i (SD)  
480p (SD)  
720p (HD)  
1080i (HD)  
Provides 480 lines of resolution. Displays images using interlaced scanning, which first  
transmits all the odd lines on the TV screen and then the even lines.  
Provides 480 lines of resolution. Displays images using progressive scanning, which transmits  
each line from top to bottom.  
Provides 720 lines of resolution. Displays images using progressive scanning, which transmits  
each line from top to bottom.  
Provides 1080 lines of resolution. Displays images using interlaced scanning, which first  
transmits all the odd lines on the TV screen and then the even lines. 1080i is one of the  
formats used by HDTV (High Definition TV).  
96  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Contacting Sony  
Troubleshooting  
If, after reading these operating instructions, you have additional  
questions related to the use of your Sony television, please call our  
Customer Information Services Center at 1-800-222-SONY (7669) (US  
residents only) or (416) 499-SONY (7669) (Canadian residents only).  
Before calling Sony customer support, please write down the model  
and serial numbers of your TV. You’ll find this information on the  
front cover of this manual.  
Remote Control  
Problem  
Possible Remedies  
Remote control  
does not operate  
The batteries could be weak. Replace the batteries.  
Check the orientation of the batteries.  
Press the TV FUNCTION button. You may have inadvertently pressed the  
SAT/CABLE FUNCTION button, which changes the remote control to SAT or  
CABLE mode.  
Make sure the TV’s power cord is connected securely to the wall outlet.  
Locate the TV at least 3-4 feet away from fluorescent lights.  
If you are using the TV to change channels, first press the TV FUNCTION  
button.  
Cannot change channels  
with the remote control  
If you are using another device to change channels, be sure you have not  
inadvertently switched your TV from the channel 3 or 4 setting. Use the  
Channel Fix option to “fix” the channel based on the hookup you used (see  
page 84).  
If you are using another device to change channels, be sure to press the  
FUNCTION button for that device. For example, if you are using your cable box  
to change channels, be sure to press the SAT/CABLE FUNCTION button.  
If you replaced the batteries to the remote recently, the code numbers for  
the video equipment may need to be reset.  
There may be more than one code for the equipment that you are  
attempting to operate.  
There is a possibility that some non-Sony equipment cannot be operated by  
your Sony TV remote.You may need to use the equipment’s original  
remote control.  
Remote control  
does not operate non-Sony  
video equipment  
97  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Channels  
Problem  
Possible Remedies  
Cannot receive upper  
channels (UHF) when  
using an antenna  
Use Auto Program in the Channel Menu to add receivable channels that are  
not presently in the TV’s memory (see page 84).  
TV is fixed to one channel  
Use Auto Program in the Channel Menu to add receivable channels that are  
not presently in the TV’s memory (see page 84).  
Check your Channel Fix settings (see page 84).  
Use Auto Program in the Channel Menu to add receivable channels that are  
not presently in the TV’s memory (see page 84).  
Cannot receive any  
channels when using  
cable TV  
Cannot receive or select  
channels  
Some digital cable channels  
are not being displayed  
Use Auto Program in the Channel Menu to add receivable TV channels that  
are not presently in TV memory (see page 84).  
Certain cable TV companies have limitations on the broadcast of digital  
cable channels. Check with your cable TV company for more information.  
Check with your cable TV company if the channels are scrambled or  
encrypted. You will need a CableCARD or a separate set-top box to view  
those channels.  
Some optional digital cable broadcast formats may not be supported. If  
your cable TV company is broadcasting digital signals in unsupported  
broadcast formats, you will need a separate set-top box provided by your  
cable TV company to view those channels.  
The digital cable channel may be set to Hide in the Channel Menu (see  
page 85).  
Use the Digital Channels feature to search for new digital channels (see  
page 84).  
CableCARD  
Problem  
Possible Remedies  
Problems using  
CableCARD or  
CableCARD services  
Check that the CableCARD is inserted properly (see pages 41-42).  
The CableCARD must be activated by your local cable TV provider before  
you can receive digital cable TV services. See the activation instructions on  
pages 41-42.  
Check the Diagnostics and CableCARD menu options (see page 93). (This can  
be useful in providing information to an authorized technician or repair  
person.)  
Contact your cable TV company.  
Cannot record  
CableCARD signals  
Digital cable is a new technology and its signals cannot be recorded in  
traditional ways (for example, by using a VCR). If you are interested in  
recording these signals, you will need a digital cable ready recording  
device. Consult your retailer for more information.  
98  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Memory Stick  
Problem  
Possible Remedies  
Image does not  
display/Cannot see all files  
Make sure the image file is a JPEG (.jpg, .jpeg) file or an MPEG1 (.mpg,  
.mpeg) file.  
Make sure the Memory Stick is inserted properly (see page 64).  
Check the Filter option setting (see page 74).  
Check the Select Contents setting (see page 74) and ensure that files are either  
in DCF directories if Digital Camera Folders is selected (see page 74), or in the  
currently selected folder if Select a Folder is selected (see page 74).  
The maximum number of files the Memory Stick Viewer can display is  
2,000 files total, including all JPEG, MPEG1, and MP3 files.  
If you are using a Memory Stick with the Memory Select function, try  
changing the position of the A/B select switch.  
JPEGs captured using a digital video camera may appear to display motion  
in full screen. This is a result of the way digital video cameras record still  
images, and is not a result of a malfunction with the TV.  
The Memory Stick might be locked. Unlock the Memory Stick and try  
rotating the image again.  
JPEG image displays  
undesirable motion or flicker  
in full screen  
Rotation not saved after  
Memory Stick is ejected or  
Memory Stick Viewer is  
closed  
The file might not have information (EXIF data) that is usually generated  
when a digital camera records a photo. In this case, it is not possible to save  
the rotation.  
There might be insufficient space on the Memory Stick to save the rotated  
file. Try deleting one or more files and rotating the image again.  
Cannot Rotate, Zoom, Pan or These functions are available only for JPEG files.  
Print Mark MPEG files  
Cannot show (or hide) file  
information in full screen or  
Slide Show  
Set the File/Information option to On or Off (see page 73).  
Cannot set print quantity  
The Memory Stick might be locked. Unlock the Memory Stick and try  
setting the print quantity again.  
Cannot see Menu  
Cannot hear audio while  
using Memory Stick  
Press V to display the Menu again.  
Check the TV’s volume or Speaker (page 81) settings.  
To hear JPEG voice memo in full screen view, select the Digital Camera Folders  
option and set the Filter option to Show All.  
Check that the Music option is not to set to Off (see page 73).  
Not all MP3 files on Memory The Memory Stick Viewer can display a maximum of 2,000 files total,  
Stick are included when the  
Music /Complete List option is  
selected (page 73)  
Cannot see MP3 list to play  
music  
MP3 file does not play back  
correctly  
MP3 files on the Memory  
Stick are not listed  
including all JPEG, MPEG1, and MP3 files.  
Make sure that the file is named with the file extension (.mp3).  
MP3 files on your Memory Stick only can be played as background music  
during a Slide Show (see page 73).  
The Memory Stick Viewer supports only MP3 files with a fixed data rate of  
128 kbps (kilobits per second).  
Only MP3 files that are named with the file extension (.mp3) are displayed  
in the list.  
MP3 files are played in alphabetical order, according to the folder in which  
they are stored. If you want to change the playing order, rename your files  
alphabetically in the order in which you want them to play or create an  
MP3 playlist (.m3u file) on a PC.  
Music files are playing in  
wrong order  
99  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Problem  
Possible Remedies  
Print Marks (DPOF) set by  
the Memory Stick Viewer are  
not recognized by the DPOF-  
compatible photo printer.  
MPEG1 movie does not  
play back correctly  
The DPOF Print Mark feature works only on photos containing EXIF data  
(data stored by the camera) that are located within the digital camera  
(DCF) folders (see “About DCF File Names” on page 75 for a description).  
Some variations of MPEG1 movies may not be compatible with the  
Memory Stick Viewer.  
MPEG movies recorded in VX Fine mode with Sony digital cameras cannot  
be played back with the Memory Stick Viewer.  
MPEG1 quality is poor when The quality of the movie when enlarged depends on the resolution of the  
enlarged (page 71)  
Error message  
is displayed  
MPEG1 file. See your camera’s instruction manual for details.  
No Memory Stick  
Memory Stick  
Locked  
There is no Memory Stick in the slot.  
The lock mechanism on the Memory Stick is  
engaged.  
Memory Stick Error  
The Memory Stick in the slot might be damaged;  
try a different Memory Stick.  
The Memory Stick may have been formatted using  
a PC or other device that is not compatible with  
cameras.  
Format Error  
Error icon is displayed  
The file is not a valid MPEG1 or JPEG format, or it  
is a progressive JPEG (which is not supported).  
The thumbnail is not DCF-compatible.  
The file is a JPEG or an MPEG1, but the thumbnail  
is unreadable.  
The file is unreadable.  
Audio  
Problem  
Possible Remedies  
Good picture,  
no sound  
Press MUTING so that the word Muting disappears from the screen (see page  
47).  
Make sure the Speaker option is set to On in the Audio Menu (see page 81).  
Make sure the MTS option is set to Stereo or Mono (see page 80).  
Cannot gain enough volume Increase the volume of the cable box using the cable box’s remote control.  
when using a cable box  
Sound seems weak or  
insufficient  
Then press TV FUNCTION and adjust the TV’s volume.  
The TV’s audio might be set to Auto SAP or Mono, when it might be better set  
to Stereo. In the Audio Menu (see page 80), set the MTS setting to Stereo. If  
already set to Stereo, switch to Mono (which may reduce background noise  
during weak stereo broadcasts).  
If the Speaker option is set to Off and the Audio Out option is set to Fixed (in  
order to output the sound to your audio system) use your audio receiver to  
adjust the sound (see page 80). Or, to use the TV remote control, set the  
Audio Out option to Variable.  
Cannot raise the volume on  
external audio speakers  
To turn on the TV speakers, set the Speaker option to On (see page 80).  
100  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Video  
Problem  
Possible Remedies  
No picture  
(screen not lit), no sound  
If your TV does not turn on, and a red light keeps flashing, your TV may  
need service. Call your local Sony Service Center.  
Make sure the power cord is plugged in.  
Press the POWER button on the front of the TV.  
Press the TV/VIDEO button to cycle through the connected video sources.  
Try another channel; it could be station trouble.  
Adjust the Picture option in the Video Menu (see page 78).  
Adjust the Brightness option in the Video Menu (see page 78).  
Check the antenna/cable connections.  
Adjust the Color option in the Video Menu (see page 78).  
Check the antenna/cable connections.  
Try another channel; it could be station trouble.  
Press ANT to change the input mode (see page 47).  
Adjust the antenna.  
Move the TV away from noise sources such as cars, neon signs, or hair-  
dryers.  
Dark, poor or no  
picture (screen lit),  
good sound  
No color  
Only snow and noise  
appear on the screen  
Dotted lines  
or stripes  
Double images or ghosts  
“Black box” on screen  
Using a highly directional outdoor antenna or a cable may solve the  
problem.  
You have selected a text option in the Setup Menu and no text is available.  
(See page 89 to reset Setup selections.) To turn off this feature, set the  
Caption Vision option to Off. If you were trying to select closed captioning,  
select CC1 instead of TEXT 1-4.  
Bars appear at the  
top and bottom of the screen  
Some wide-screen programs are filmed in aspect ratios that are greater  
than 16:9, such as 2.35:1. (This is especially common with theatrical  
releases). Your TV will show these programs with bars at the top and  
bottom of the screen. For more details, check the documentation that came  
with your DVD (or contact your program provider).  
General  
Problem  
Possible Remedies  
How to reset TV to  
factory settings  
Turn on the TV. While holding down the RESET button on the remote  
control, press the POWER button on the TV. (The TV will turn itself off, then  
back on again.) Release the RESET button.  
How to restore Video settings Press the RESET button on the remote control while in the Video Menu (see  
to factory settings  
page 78).  
How to restore Audio  
settings to factory settings  
Cannot cycle through the  
other video equipment  
connected to the TV  
Press the RESET button on the remote control while in the Audio Menu (see  
page 80).  
Be sure the Video Label option is not set to Skip (see page 90).  
Cannot operate Menu  
If a Menu option appears in gray, this indicates that the TV is in a state in  
which the Menu option is not available.  
In the password screen (see page 86), enter the following master password:  
4357. The master password clears your previous password; it cannot be  
used to temporarily unblock channels.  
Lost password  
101  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Problem  
TV makes “popping” sound This is a normal sound that results from the TV automatically degaussing  
when turned on each time it is turned on.  
TIMER/STAND BY LED on This LED blinks when the TV is turned on, then shuts off when the picture  
Possible Remedies  
front panel is lit  
(XS955 models only)  
POWER LED on front panel  
is lit  
is displayed. If the LED blinks for more than a minute, this may indicate  
the TV needs service.  
(XS945 models only)  
Digital cable box does not  
work  
If you are connecting a VCR and digital cable box using a splitter, as  
described on page 24, you must use a special bi-directional splitter that is  
designed to work with your digital cable box. Contact your cable TV  
company for details.  
Cannot record digital  
channels to VCR  
Only analog channels can be recorded to your VCR.  
102  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Specifications  
Picture Tube  
FD Trinitron® tube  
Antenna  
75 ohm external terminal for VHF/UHF  
Television System  
NTSC  
American TV Standard  
ATSC (8VSB terrestrial)  
ATSC compliant 8VSB  
QAM on cable  
ANSI/SCTE 07 2000  
Channel Coverage  
Terrestrial (analog)  
Cable TV (analog)  
Terrestrial (digital)  
Cable TV (digital)  
120V, 60 Hz  
2-69  
1-125  
2-69  
1-135  
Power Requirements  
Inputs/Outputs  
HDMI IN  
Video  
Audio  
1080i, 720p, 480p, 480i  
Two channel linear PCM 32, 44.1 and 48 kHz, 16,  
20 and 24 bit  
Video (IN)  
S Video (IN)  
4 total (1 on front panel)  
3 total (1 on front panel)  
1 Vp-p, 75 ohms unbalanced, sync negative  
Y: 1 Vp-p, 75 ohms unbalanced, sync negative  
C: 0.286 Vp-p (Burst signal), 75 ohms  
Audio (IN)  
7 total (1 on front panel)  
2 (Y, PB, PR)  
500 mVrms (100% modulation)  
Impedance: 47 kilohm  
Y: 1.0 Vp-p, 75 ohms unbalanced, sync negative;  
PB: 0.7 Vp-p, 75 ohms  
Component Video Input  
PR: 0.7 Vp-p, 75 ohms  
CONTROL S (IN/OUT)  
Variable/Fixed Audio (OUT)  
1
1
More than 408 mVrms at the maximum volume  
setting (Variable)  
More than 408 mVrms (Fixed)  
Impedance (output): 2 kilohms  
Digital Audio Optical Output  
PCM/Dolby Digital  
1
Optical Rectangular  
CableCARD Slot  
Supplied Accessories  
PCMCIA Type I/II  
Remote Control  
AA (R6) Batteries  
KD-30XS955  
RM-Y199  
2 supplied for remote control  
30 in (762 mm)  
Visible Screen Size  
(picture measured diagonally)  
KD-32XS945  
KD-34XS955  
KD-36XS955  
KD-30XS955  
KD-32XS945  
KD-34XS955  
KD-36XS955  
32 in (812.8 mm)  
34 in (863.6 mm)  
36 in (914.4 mm)  
32 in (812.8 mm)  
34 in (863.6 mm)  
36 in (914.4 mm)  
38 in (965.2 mm)  
Actual CRT Size  
(picture measured diagonally)  
Speaker Output  
7.5 W x 2 + 15 W subwoofer  
Dimensions (W x H x D)  
KD-30XS955  
898 x 604 x 564.5 mm  
(35 3/8 x 23 3/4 x 22 1/4 in)  
KD-32XS945  
898 x 698 x 598 mm  
(35 3/8 x 27 1/2 x 23 1/2 in)  
KD-34XS955  
KD-36XS955  
KD-30XS955  
KD-32XS945  
KD-34XS955  
KD-36XS955  
994 x 654 x 604 mm (39 1/8 x 25 3/4 x 23 3/4 in)  
994 x 776.5 x 634 mm (39 1/8 x 30 5/8 x 25 in)  
67 Kg (148 lbs)  
81 Kg (178.5 lbs)  
93 Kg (205 lbs)  
Mass  
108.2 Kg (238.5 lbs)  
103  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Power Consumption  
KD-30XS955  
KD-32XS945  
KD-34XS955  
KD-36XS955  
In Use: 220 W  
In Standby: 3 W  
In CableCARD Standby: 20 W  
In Use: 240 W  
In Standby: 3 W  
In CableCARD Standby: 20 W  
In Use: 250 W  
In Standby: 3 W  
In CableCARD Standby: 20 W  
In Use: 270 W  
In Standby: 3 W  
In CableCARD Standby: 20 W  
Design and specifications are subject to change without notice.  
Optional  
Accessories  
Accessory  
Description  
Model Number  
VMC-810/820/830 HG  
RKC-515HG  
VMC-10/30 HG  
SU-30HX1  
SU-32HX1  
SU-34HX1  
SU-36HX1  
Cables  
Audio/Video  
Audio  
Component Video  
KD-30XS955  
KD-32XS945  
KD-34XS955  
KD-36XS955  
TV Stands  
104  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Index  
0-9 buttons 48, 52  
channel list, setting up 43  
Channel Menu 77  
Channel Skip/Add 85  
CineMotion 10, 47, 79  
ClearEdge VM 79  
ClearEdge VM Velocity  
Modulation 10  
clearing, Favorite Channels 58  
closed caption modes 77, 89  
CODE SET button 47  
color, adjusting 78  
Component Video Inputs 10  
CONTROL S 40  
CONTROL S IN/OUT jacks,  
Cool, Color Temperature 78  
Fixed audio setting 81  
Full (Screen Mode) 55, 56  
4:3 Default settings 82, 83  
A
Advanced Video 79  
Alternate Audio 54  
Alternate Video 54  
ANT button 52  
GUIDE button 48, 53  
antenna, connecting 17  
aspect ratio 83  
Audio Menu 77  
HD Detailer 10  
HD/DVD IN  
Audio Out 81  
(1080i/720p/480p/480i)  
jacks, described 15  
High-Definition Multimedia  
Interface (HDMI) 10, 37, 38,  
AUDIO OUT jack 15  
audio receiver, connecting 36  
Auto Program (channel setup)  
43, 84  
Auto SAP, MTS setting 80  
Horizontal Expand (Screen  
Mode) 56, 57  
D
degauss 102  
B
hue, adjusting 78  
DIGITAL AUDIO OPTICAL jack  
balance, adjusting 80  
bass, adjusting 80  
batteries, inserting in remote 45  
bilingual audio 80  
blocking programs. See ratings.  
brightness, adjusting 78  
Built 9  
15  
I
digital channels, adding 84  
Digital Reality Creation 10  
DISPLAY button 52  
DRC Mode 79  
DRC MODE button 47  
DRC. See Digital Reality Creation.  
DVD player  
Info Banner 89  
Initial Setup 43  
interlaced 10, 47, 79, 96  
J
JUMP button 47, 52  
C
cable  
using with TV remote  
control 60  
with A/V connectors,  
connecting 17  
with VCR, connecting 23  
cable box  
Language, setting 90  
M
connecting with VCR 24  
using with TV remote  
control 60  
Memory Stick  
button 47  
E
Effect button 47  
features 61  
Index 66  
ENTER button 48, 52  
error messages, Memory Stick  
CABLE jack, described 15  
CableCARD 9, 15, 16, 41  
CableCARD slot 15, 41, 42  
CableCARD, activating 41  
CableCARD, inserting card 41  
CableCARD, removing card 42  
Caption Vision 89  
CATV. See cable  
indicator (LED) 12, 13  
inserting 64  
insertion slot 12, 13  
panning photos 70  
photo options 69  
playing movies 71  
precautions 76  
removing 65  
F
Fast-forward button 47  
Favorite Channels 10  
clearing 58  
CH buttons 12, 13, 48  
Channel Fix 84  
in Channel Menu 84  
using 58  
105  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
rotating photos 70  
troubleshooting 99  
viewing photos 68  
zooming photos 70  
Memory Stick button 12, 13  
Memory Stick Viewer 10  
MENU button 12, 13, 48, 52,  
58, 77  
TV POWER button 47, 52  
TV/VIDEO button 48, 52  
ratings, setting 8688  
ratings, viewing blocked  
programs 87, 88  
Record buttons 47  
remote control  
Variable audio setting 81  
using with TV remote  
inserting batteries 45  
programming 4950  
removing, Favorite Channels 58  
RESET button 47, 58  
Video options 79  
control 59  
with cable box, connecting  
24  
with cable, connecting 23  
with satellite receiver,  
connecting 30  
Menus  
Audio 77  
Channel 77  
Parent 77, 86  
Setup 89  
Vertical Center 82  
Vertical Correction 43, 90  
Vertical Expand (Screen Mode)  
Video 77  
MONITOR OUT 15  
Mono, MTS setting 80  
Movie mode 78  
movies  
viewing thumbnails 66  
MTS 80  
S
S VIDEO jack, described 12, 13,  
Vertical Size, adjusting 82  
VHF/UHF jack, described 15  
VIDEO (L/R)/AUDIO jacks,  
described 15  
Video Menu 77  
Video modes, selecting 78  
Vivid mode 78  
SAT/CABLEFUNCTION button  
47  
SAT/CABLE POWER button 47  
satellite receiver, using with TV  
remote control 59  
Screen Mode 55, 57, 82, 83  
SCREEN MODE button 55  
Setup Menu 89  
sharpness, adjusting 78  
Simulated, Effect 80  
SLEEP button 47  
MUTING button 47, 52  
N
Neutral, Color Temperature 78  
Normal (Screen Mode) 55  
VOL buttons 12, 13, 47, 52  
O
Warm, Color Temperature 78  
Wega, described 9  
Wide Zoom 55  
off, turning off the TV 12, 13  
on, turning on the TV 12, 13  
speakers  
turning on/off 81  
P
using external speakers 81  
specifications 104  
Parent Menu 77, 86  
parental control, described 10  
password, changing 86  
Pause button 47  
Standard mode 78  
Steady Sound, described 10  
Steady Sound, setting 80  
Stereo, MTS setting 80  
Stop button 47  
Super Fine Pitch 10  
surround sound 80  
SYSTEM OFF button 47  
Zoom (Screen Mode) 55, 56  
photos  
viewing thumbnails 66  
PIC MODE button 47  
picture contrast, adjusting 78  
Play button 47  
POWER button 12, 13  
power cord, removing from  
holder 11  
powering on/off, the TV 12, 13  
presetting channels 84  
Pro (Video) mode 78  
Program Guide 53  
program guide 53  
Tilt Correction 43, 90  
tilt, correcting 43, 90  
transport buttons 47  
treble, adjusting 80  
troubleshooting 97102  
TruSurround 80  
progressive 10, 47, 79, 96  
TruSurround, Effect 80  
turning on/off the TV 12, 13  
TV FUNCTION button 47, 52  
106  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Snapper Lawn Aerator 4571 User Manual
Sony Automobile Accessories RM X1S User Manual
Sony Cassette Player CFD S350 User Manual
Sony CRT Television KLV 15SR3U User Manual
Sony Outboard Motor GDM C250K User Manual
SoundMax Home Theater System SM CDM1042 User Manual
Southbend Hot Beverage Maker KDLS 20F User Manual
Superior Indoor Fireplace SSDVR 3530CNE User Manual
Sylvania CRT Television SRT2113A User Manual
Sylvania CRT Television W3913LC User Manual