Sony Blu ray Player BDP S300 User Manual

3-214-290-11(1)  
B D P - S 3 0 0  
B D P - S 3 0 1  
B l u - r a y D i s c P l a y e r  
O p e r a t i n g I n s t r u c t i o n s  
©2007 Sony Corporation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Note  
WARNING  
Notes About the  
Discs  
This equipment has been tested and found to comply  
with the limits for a Class B digital device, pursuant  
to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against  
harmful interference in a residential installation.  
This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and used  
in accordance with the instructions, may cause  
harmful interference to radio communications.  
However, there is no guarantee that interference will  
not occur in a particular installation. If this  
equipment does cause harmful interference to radio  
or television reception, which can be determined by  
turning the equipment off and on, the user is  
encouraged to try to correct the interference by one  
or more of the following measures:  
To reduce the risk of fire or electric  
shock, do not expose this apparatus to  
rain or moisture.  
To avoid electrical shock, do not open  
the cabinet. Refer servicing to qualified  
personnel only.  
• To keep the disc clean, handle the disc  
by its edge. Do not touch the surface.  
The AC power cord must be changed  
only at a qualified service shop.  
– Reorient or relocate the receiving antenna.  
– Increase the separation between the equipment and  
receiver.  
– Connect the equipment into an outlet on a circuit  
different from that to which the receiver is  
connected.  
– Consult the dealer or an experienced radio/TV  
technician for help.  
CAUTION  
The use of optical instruments with this  
product will increase eye hazard. As the  
laser beam used in this Blu-ray Disc  
player is harmful to eyes, do not attempt  
to disassemble the cabinet.  
• Do not expose the disc to direct  
sunlight or heat sources such as hot air  
ducts, or leave it in a car parked in  
direct sunlight as the temperature may  
rise considerably inside the car.  
For customers in the U.S.A  
If this product is not working properly, please call 1-  
800-222-7669.  
Owner’s Record  
Refer servicing to qualified personnel  
only.  
The model and serial numbers are located at the rear  
of the unit. Record the serial number in the space  
provided below. Refer to them whenever you call  
upon your Sony dealer regarding this product.  
• After playing, store the disc in its case.  
• Clean the disc with a cleaning cloth.  
Wipe the disc from the center out.  
Model No. BDP-S300  
BDP-S301  
Serial No.______________  
For Customers in Canada  
If this product is not working properly, please call 1-  
877-602-2008 for Peace of Mind Warranty  
Replacement service.  
For other product related questions please contact  
our Customer Information Service Center at  
1-877-899-7669 or write to us at: Customer  
Information Service 115 Gordon Baker Road,  
Toronto, Ontario, M2H 3R6  
This label is located on the laser  
protective housing inside the enclosure.  
• Do not use solvents such as benzine,  
thinner, commercially available disc/  
lens cleaners, or anti-static spray  
intended for vinyl LPs.  
• If you have printed the disc’s label, dry  
the label before playing.  
This symbol is intended to alert the  
user to the presence of uninsulated  
“dangerous voltage” within the  
product’s enclosure that may be of  
sufficient magnitude to constitute a risk  
of electric shock to persons.  
This symbol is intended to alert the  
user to the presence of important  
operating and maintenance (servicing)  
instructions in the literature  
accompanying the appliance.  
CAUTION  
You are cautioned that any changes or modifications  
not expressly approved in this manual could void  
your authority to operate this equipment.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
On operation  
• If the player is brought directly from a  
cold to a warm location, or is placed in  
a very damp room, moisture may  
condense on the lenses inside the  
player. Should this occur, the player  
may not operate properly. In this case,  
remove the disc and leave the player  
turned on for about half an hour until  
the moisture evaporates.  
Important Safety Precautions  
Instructions  
1) Read these instructions.  
On safety  
2) Keep these instructions.  
3) Heed all warnings.  
• To prevent fire or shock hazard, do not  
place objects filled with liquids, such  
as vases, on the apparatus.  
• Should any solid object or liquid fall  
into the cabinet, unplug the player and  
have it checked by qualified personnel  
before operating it any further.  
4) Follow all instructions.  
• When you move the player, take out  
any discs. If you don’t, the disc may be  
damaged.  
5) Do not use this apparatus near water.  
6) Clean only with dry cloth.  
7) Do not block any ventilation  
openings. Install in accordance with  
the manufacturer’s instructions.  
8) Do not install near any heat sources  
such as radiators, heat registers,  
stoves, or other apparatus (including  
amplifiers) that produce heat.  
9) Do not defeat the safety purpose of  
the polarized or grounding-type  
plug. A polarized plug has two  
blades with one wider than the other.  
A grounding type plug has two  
blades and a third grounding prong.  
The wide blade or the third prong are  
provided for your safety. If the  
provided plug does not fit into your  
outlet, consult an electrician for  
replacement of the obsolete outlet.  
10) Protect the power cord from being  
walked on or pinched particularly at  
plugs, convenience receptacles, and  
the point where they exit from the  
apparatus.  
On adjusting volume  
Do not turn up the volume while  
listening to a section with very low level  
inputs or no audio signals. If you do, the  
speakers may be damaged when a peak  
level section is played.  
On power sources  
• The player is not disconnected from the  
AC power source as long as it is  
connected to the wall outlet, even if the  
player itself has been turned off.  
• If you are not going to use the player  
for a long time, be sure to disconnect  
the player from the wall outlet. To  
disconnect the AC power cord, grasp  
the plug itself; never pull the cord.  
On cleaning  
Clean the cabinet, panel, and controls  
with a soft cloth slightly moistened with  
a mild detergent solution. Moreover,  
wipe the glass part on the front panel  
with a soft, dry cloth. Do not use any  
type of abrasive pad, scouring powder or  
solvent such as alcohol or benzine.  
On placement  
• Place the player in a location with  
adequate ventilation to prevent heat  
build-up in the player.  
On cleaning discs, disc/lens  
cleaners  
• Do not place the player on a soft  
surface such as a rug.  
• Do not place the player in a location  
near heat sources, or in a place subject  
to direct sunlight, excessive dust, or  
mechanical shock.  
• Do not install the player in an inclined  
position. It is designed to be operated  
in a horizontal position only.  
• Keep the player and the discs away  
from equipment with strong magnets,  
such as microwave ovens, or large  
loudspeakers.  
Do not use a commercially available  
cleaning disc or disc/lens cleaner (wet or  
spray type). These may cause the  
apparatus to malfunction.  
11) Only use attachments/accessories  
specified by the manufacturer.  
12) Use only with the cart, stand, tripod,  
bracket, or table specified by the  
manufacturer, or sold with the  
apparatus. When a cart is used, use  
caution when moving the cart/  
apparatus combination to avoid  
injury from tip-over.  
On replacement of parts  
In the events that this player is repaired,  
repaired parts may be collected for reuse  
or recycling purposes.  
IMPORTANT NOTICE  
Caution: This player is capable of  
holding a still video image or on-screen  
display image on your television screen  
indefinitely. If you leave the still video  
image or on-screen display image  
displayed on your TV for an extended  
period of time you risk permanent  
damage to your television screen.  
Plasma display panel televisions and  
projection televisions are susceptible to  
this.  
• Do not place heavy objects on the  
player.  
• Do not install this player in a confined  
space, such as a bookshelf or similar  
unit.  
• Install this player so that the power  
cord can be unplugged from the wall  
socket immediately in the event of  
trouble.  
• Do not expose the battery to excessive  
heat such as direct sunlight, fire or the  
like.  
13) Unplug this apparatus during  
lightning storms or when unused for  
long periods of time.  
14) Refer all servicing to qualified  
service personnel. Servicing is  
required when the apparatus has  
been damaged in any way, such as  
power-supply cord or plug is  
damaged, liquid has been spilled or  
objects have fallen into the  
apparatus, the apparatus has been  
exposed to rain or moisture, does not  
operate normally, or has been  
dropped.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Adjusting the Pictures ......................................28  
Locking a Disc ....................................................29  
Table of Contents  
WARNING ...............................................................2  
Notes About the Discs ........................................2  
Important Safety Instructions ...........................3  
Precautions ...........................................................3  
Table of Contents .................................................4  
Viewing All Titles ...............................................32  
Searching for a Title ..........................................34  
Discs and Files ................................................5  
About playback of discs recorded in AVCHD  
Main Features .......................................................7  
Viewing All Artists .............................................36  
Quicklist, or Folder ......................................38  
Searching for a Track .......................................38  
Step 1: Unpacking ...............................................9  
Cord .................................................................10  
A Connecting to a video input jack ...................10  
B Connecting to an S VIDEO input jack ...........10  
C Connecting to component video input jacks  
(Y, PB, PR) ....................................................10  
D Connecting to an HDMI input jack ................11  
About the ‘BRAVIA’ Theatre Sync features  
Viewing All Folders ...........................................40  
Searching for a Photo .......................................42  
(Quicklist) .......................................................43  
Using the Setup Displays ................................44  
Video Setup .........................................................45  
Audio Setup .........................................................47  
Language .............................................................49  
Parental Control .................................................50  
Speakers ...............................................................51  
Options .................................................................52  
Resetting the Player ..........................................53  
Connecting to a stereo amplifier (receiver)  
and 2 speakers .............................................13  
Connecting to an AV amplifier (receiver)  
decoder and 3 to 6 speakers ........................14  
Connecting to an AV amplifier (receiver)  
with 5.1ch input jacks and 6 speakers .........14  
Connecting to an AV amplifier (receiver)  
with a digital input jack and 6 speakers ........15  
Connecting to an AV amplifier (receiver)  
with an HDMI input jack and 8 speakers ......15  
Step 5: Preparing the Remote ........................16  
If you want to control your TV with the supplied  
Step 6: Easy Setup ............................................18  
Step 7: Additional Adjustments .....................19  
Troubleshooting .................................................54  
Self-Diagnosis Function ...................................57  
Index to Parts and Controls ............................58  
Front panel .........................................................58  
Rear panel .........................................................59  
GNU License Information ................................60  
Glossary ...............................................................66  
Specifications .....................................................67  
Language Code List ..........................................68  
Index ......................................................................70  
Playing a Disc .....................................................20  
Guide to Displays ...............................................22  
Guide to the Remote .........................................24  
Checking the Disc Information .......................26  
(Audio DRC) ...................................................27  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
About this manual  
Instructions in this manual describe the controls on the remote.  
You can also use the controls on the player if they have the same  
or similar names as those on the remote.  
The meanings of the icons used in this manual are described  
below:  
This Player Can Play the  
Following Discs and Files  
Disc Format  
Icon  
Meaning  
Blu-ray Disc  
Functions available for BD-ROMs  
including DL discs.  
BD  
Functions available for DVD VIDEOs and  
DVD+RWs/DVD+Rs in +VR mode or  
DVD-RWs/DVD-Rs in video mode,  
including 8 cm discs.  
DVD  
DATA DVD  
CD  
DVD VIDEO  
DVD-RW/-R  
Functions available for DATA DVDs  
(DVD+RWs/DVD+Rs/DVD-RWs/DVD-  
Rs containing MPEG-2 PS movie files,  
MP3* audio tracks, and JPEG image files).  
DVD+RW/+R  
CD  
Functions available for music CDs or CD-  
Rs/CD-RWs in music CD Format.  
* MP3 (MPEG-1 Audio Layer III) is a standard format defined by ISO  
(International Organization for Standardization)/IEC (International  
Electrotechnical Commission) MPEG which compresses audio data.  
“Blu-ray Disc” is a trademark.  
“Blu-ray Disc,” “DVD+RW,” “DVD-RW,” “DVD+R,” “DVD-  
R,” “DVD VIDEO,” and “CD” logos are trademarks.  
Note  
The on-screen display illustrations used in this manual may not match  
the graphics displayed on your TV screen.  
Supported file formats (DATA DVD only)  
DVD+RWs/DVD-RWs/DVD+Rs/DVD-Rs are called “DATA  
DVD” in this manual when the discs contain playable files. The  
following file formats are supported:  
• MPEG-2 PS movie files.  
• MP3 music files.  
• JPEG* image files.  
* JPEG format conforming to UDF (Universal Disk Format).  
Notes about BD-ROM compatibility  
This player supports BD-ROM Profile 1 only. Playback of later  
versions and BDs other than BD-ROM is not guaranteed. Since  
the Blu-ray Disc specifications are new and evolving, some discs  
may not play depending on the disc type and the version.  
The audio output differs depending on the source, connected  
output jack, and selected audio settings. For details, see page 48.  
,continued  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Examples of discs that the player  
cannot play  
About playback of discs recorded in  
AVCHD format  
The player cannot play the following discs:  
This player can play AVCHD format discs.  
• BD-REs/BD-Rs.  
TM  
• BDs with cartridge.  
• DVD-RWs/DVD-Rs of VR mode.  
• DVD-RAMs.  
• HD DVDs.  
• DVD Audio discs.  
• DATA CDs (CD-Rs/CD-RWs other than music CD format).  
• CD-ROMs recorded in PHOTO CD format.  
• Data part of CD-Extras.  
What is the AVCHD format?  
The AVCHD format is a high definition digital video camera  
format used to record SD (standard definition) or HD (high  
1
definition) signals of either the 1080i specification* or the 720p  
2
specification* on DVDs, using efficient data compression  
• VCDs/Super VCDs.  
coding technology. The MPEG-4 AVC/H.264 format is adopted  
to compress video data, and the Dolby Digital or Linear PCM  
system is used to compress audio data. The MPEG-4 AVC/  
H.264 format is capable of compressing images at higher  
efficiency than that of the conventional image compressing  
format. The MPEG-4 AVC/H.264 format enables a high  
definition (HD) video signal shot on a digital video camera  
recorder to be recorded on DVD discs, in the same way as it  
would be for a standard definition (SD) television signal.  
• HD layer on Super Audio CDs.  
Also, the player cannot play the following discs:  
• A BD-ROM/DVD VIDEO with a different region code.  
• A disc recorded in a color system other than NTSC, such as  
PAL (this player conforms to the NTSC color system).  
• A disc that has a non-standard shape (e.g., card, heart).  
• A disc with paper or stickers on it.  
• A disc that has the adhesive of cellophane tape or a sticker still  
left on it.  
“AVCHD” and the AVCHD logo are trademarks of Matsushita Electric  
Industrial Co., Ltd. and Sony Corporation.  
Notes  
• Notes about DVD+RWs/DVD+Rs, DVD-RWs/DVD-Rs, or CD-Rs/  
CD-RWs  
Some DVD+RWs/DVD+Rs, DVD-RWs/DVD-Rs, or CD-Rs/  
CD-RWs cannot be played on this player due to the recording  
quality or physical condition of the disc, or the characteristics  
of the recording device and authoring software.  
1
*
*
A high definition specification which utilizes 1080 effective scanning  
lines and the interlace system.  
A high definition specification which utilizes 720 effective scanning  
lines and the progressive system.  
2
The DVD disc will not play if it has not been correctly  
finalized. For more information, refer to the operating  
instructions for the recording device. Note that some playback  
functions may not work with some DVD+RWs/DVD+Rs, even  
if they have been correctly finalized. In this case, view the disc  
by normal playback.  
Notes  
• Some AVCHD format discs may not play, depending on the recording  
condition.  
• The AVCHD format disc will not play if it has not been correctly  
finalized.  
• Music discs encoded with copyright protection technologies  
This product is designed to playback discs that conform to the  
Compact Disc (CD) standard. Recently, various music discs  
encoded with copyright protection technologies are being  
marketed by some record companies. Please be aware that  
among those discs, there are some that do not conform to the  
CD standard and may not be playable by this product.  
• Note on DualDiscs  
A DualDisc is a two sided disc product which mates DVD  
recorded material on one side with digital audio material on the  
other side.  
However, since the audio material side does not conform to the  
Compact Disc (CD) standard, playback on this product is not  
guaranteed.  
• Note about double-layer DVDs  
The playback pictures and sound may be momentarily  
interrupted when the layers switch.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
BD/DVD region code  
Your player has a region code printed on the back of the unit and  
only will play BD-ROM/DVD VIDEOs (playback only) labeled  
with identical region codes. This system is used to protect  
copyrights.  
Main Features  
ALL  
DVD VIDEOs labeled  
will also play on this player.  
Experience the high definition (HD) quality audio/video output  
and the library function of this Blu-ray Disc Player.  
Depending on the BD-ROM/DVD VIDEO, there may be no region  
code indication, even though playing the BD-ROM/DVD VIDEO is  
prohibited by area restrictions.  
BD-ROM playback  
BD-ROM is a next generation optical disc format in the HD era.  
Featuring massive storage capacity of 25 to 50 GB (five times  
larger than a DVD) and a high-speed transfer rate of up to 54  
Mbps, the format offers not only uncompromised HD quality  
1
1 2  
video* * , but also enables rich bonus content on a single disc  
COMPONENT  
VIDEO OUT  
and HD quality audio up to 8ch, and interactive operability.  
VIDEO  
OUT  
VIDEO  
AUDIO  
OUT  
5.1CH OUTPUT  
FRONT REAR CENTER  
Y
P
P
1
DIGITAL OUT  
PCM/DTS/DOLBY DIGITAL  
1
AC IN  
L
L
COAXIAL  
OPTICAL  
B
R
*
A compatible HD display device is necessary to enjoy the same  
HDMI  
OUT  
R
R
WOOFER  
S
VIDEO  
quality.  
2
*
Some discs allow viewing only with an HDMI connection.  
24p True Cinema  
Note on playback operations of BDs/  
DVDs  
Some playback operations of BDs/DVDs may be intentionally  
set by software producers. Since this player plays BDs/DVDs  
according to the disc contents the software producers designed,  
some playback features may not be available. Also, refer to the  
instructions supplied with the BDs/DVDs.  
Movies shot with a film camera consist of 24 frames per second.  
Since conventional televisions (both CRT and flat panels)  
display frames either at 1/60 or 1/50 second intervals, the 24  
frames do not appear at an even pace.  
When connected to a TV with 24p capabilities, the player  
displays each frame at 1/24 second intervals — the same interval  
originally shot with the film camera, thus faithfully reproducing  
the original cinema image.  
HDMI Control (‘BRAVIA’ Theatre Sync)  
‘BRAVIA’ Theatre Sync Function makes operations simple by  
connecting Sony components that are compatible with the  
HDMI Control function with an HDMI cord.  
Copyrights  
This product incorporates copyright protection technology that  
is protected by U.S. patents and other intellectual property rights.  
Use of this copyright protection technology must be authorized  
by Macrovision, and is intended for home and other limited  
viewing uses only unless otherwise authorized by Macrovision.  
Reverse engineering or disassembly is prohibited.  
BD-J application  
The BD-ROM format supports Java for interactive functions.  
“BD-J” offers content providers almost unlimited functionality  
when creating interactive BD-ROM titles*.  
Java and all Java-based trademarks and logos are trademarks or  
registered trademarks of Sun Microsystems, Inc. in the U.S. and  
other countries.  
Esmertec and Jbed are trademarks or registered trademarks of  
Esmertec AG.  
© 2000-2007 Esmertec AG  
* This player does not support downloadable BD-J content.  
Support of uncompressed multi-channel Linear  
PCM  
In combination with a compatible AV amplifier, the player can  
output up to 8ch Linear PCM surround sound*. With a non-  
compatible amplifier, the player can output 5.1ch analog signals  
from its 5.1CH OUTPUT jack for high quality audio enjoyment.  
* Note that the DIGITAL OUT (COAXIAL or OPTICAL) jack does not  
output 8ch signals. You will need an HDMI cord and an HDMI-  
compatible device that support 8ch signals.  
AVCHD format disc playback  
The player supports AVCHD format files–high definition  
recordings made on AVCHD-compatible camcorders. Your high  
definition personal archive is readily playable in HD quality.  
,continued  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
HDMI (High-Definition Multimedia Interface)  
digital interface  
When connected to an HDMI-equipped display device using a  
single HDMI cord, the player can output both SD to HD video  
and multi-channel audio signals, in digital form without  
degradation.  
The HDMI specification supports HDCP (High-bandwidth  
Digital Content Protection), a copy protection technology that  
incorporates coding technology for digital video signals.  
Library function for recorded files (For JPEG  
image, MP3 audio, MPEG-2 PS movie files  
only)  
With DATA DVDs created on other DVD devices, three  
separate movie/music/photo Title List-browsers allow for easy  
sorting, searching and playback including a slideshow.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step 1: Unpacking  
Check that you have the following items:  
• Video cord (phono plug × 1) (1)  
• Stereo audio cord (phono plug × 2) (1)  
• HDMI cord (1)  
(supplied with BDP-S301 only)  
• Power cord (1)  
Getting Started  
Follow steps 1 to 7 to hook up and adjust the  
settings of the player.  
For jack and button names, see “Index to  
• Remote commander (remote) (1)  
• Size AA (R6) batteries (2)  
Notes  
• Plug cords securely to prevent unwanted noise.  
• Refer to the instructions supplied with the components to  
be connected.  
• You cannot connect this player to a TV that does not have  
a video input jack.  
• Be sure to disconnect the power cord of each component  
before connecting.  
• Do not apply too much pressure on the connecting cords.  
Pushing against the cabinet wall, etc., may damage the  
cord.  
Step 1: Unpacking . . . . . . . . . . . . . . . . . . . . . . .9  
Step 2: Connecting the Video Cords/  
HDMI Cord . . . . . . . . . . . . . . . . . . . . . . . . .10  
Step 5: Preparing the Remote . . . . . . . . . . . . .16  
Step 6: Easy Setup. . . . . . . . . . . . . . . . . . . . . .18  
Step 7: Additional Adjustments . . . . . . . . . . . .19  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
B Connecting to an S VIDEO input jack  
Connect using an S VIDEO cord (not supplied). You will enjoy  
high quality images.  
Step 2: Connecting the  
Video Cords/HDMI Cord  
Blu-ray Disc player  
COMPONENT  
VIDEO OUT  
Connect this player to your TV monitor, projector or AV  
amplifier (receiver) using a video cord. Select one of the patterns  
A through D, according to the input jack on your TV monitor,  
projector or AV amplifier (receiver).  
VIDEO  
AUDIO  
OUT  
5.1CH OUTPUT  
FRONT REAR CENTER  
OUT  
VIDEO  
Y
P
P
DIGITAL OUT  
PCM/DTS/DOLBY DIGITAL  
AC IN  
L
L
COAXIAL  
OPTICAL  
B
R
HDMI  
OUT  
R
R
WOOFER  
S
VIDEO  
to S VIDEO  
In order to view 1080p progressive signals with a compatible  
TV, projector, or monitor with an HDMI input jack, you must  
select pattern D. You can use pattern C to view 480p/720p  
progressive signals or 1080i interlace signals on a compatible  
device with component video input jacks.  
VIDEO  
OUT  
VIDEO  
S VIDEO cord (not supplied)  
S VIDEO  
INPUT  
S VIDEO  
A Connecting to a video input jack  
Connect the supplied video cord (yellow) to the yellow (video)  
jack. You will enjoy standard quality images.  
TV, projector, or AV  
amplifier (receiver)  
: Signal flow  
Blu-ray Disc player  
COMPONENT  
VIDEO OUT  
VIDEO  
OUT  
VIDEO  
AUDIO  
OUT  
5.1CH OUTPUT  
FRONT REAR CENTER  
Y
P
P
DIGITAL OUT  
PCM/DTS/DOLBY DIGITAL  
AC IN  
L
L
COAXIAL  
OPTICAL  
B
R
C Connecting to component video  
HDMI  
OUT  
R
R
WOOFER  
S
VIDEO  
input jacks (Y, PB, PR)  
to VIDEO OUT  
(yellow)  
Connect the component via the COMPONENT VIDEO OUT jacks  
using a component video cord (not supplied) or three video cords  
(not supplied) of the same kind and length. You will enjoy accurate  
color reproduction and high quality images. You can also enjoy  
higher quality pictures from 480p/720p progressive signals or 1080i  
interlace signals, if your TV, projector or AV amplifier (receiver) is  
compatible.  
VIDEO  
OUT  
VIDEO  
INPUT  
VIDEO  
S VIDEO  
(yellow)  
Video cord (supplied)  
L
AUDIO  
Blu-ray Disc player  
COMPONENT  
VIDEO OUT  
R
VIDEO  
AUDIO  
OUT  
5.1CH OUTPUT  
FRONT REAR CENTER  
OUT  
VIDEO  
Y
P
P
DIGITAL OUT  
PCM/DTS/DOLBY DIGITAL  
AC IN  
L
L
COAXIAL  
OPTICAL  
B
R
HDMI  
OUT  
TV, projector, or AV  
amplifier (receiver)  
R
R
WOOFER  
S
VIDEO  
: Signal flow  
to COMPONENT  
VIDEO OUT  
COMPONENT  
VIDEO IN  
(green)  
(blue)  
(red)  
(green)  
(blue)  
(red)  
COMPONENT  
VIDEO OUT  
Y
When connecting to a standard 4:3 screen TV  
Depending on the disc, the image may not fit your TV screen. To  
change the aspect ratio, see page 45.  
Y
PB  
PR  
P
B
R
P
Note  
TV, projector, or AV  
amplifier (receiver)  
Do not connect a VCR, etc., between your TV and the player. If you pass  
the player signals via the VCR, you may not receive a clear image on the  
TV screen. If your TV has only one audio/video input jack, connect the  
player to this jack.  
Component video  
cord (not supplied)  
: Signal flow  
VCR  
Blu-ray Disc player  
TV  
Connect  
directly  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
About indicators for HDMI connection  
D Connecting to an HDMI input jack  
After the player is turned on, the HD indicator on the front panel  
lights up when outputting 720p/1080i/1080p video signals. The  
HDMI indicator lights up when an HDMI device is connected.  
Use an HDMI cord to enjoy high quality digital pictures and  
sound through the HDMI OUT jack. You will enjoy higher  
quality pictures from 480p/1080i, or 1080p (highest among the  
player output), if your TV, projector or AV amplifier (receiver)  
is compatible.  
Notes  
• Consumers should note that not all high definition television sets are  
fully compatible with this product and may cause artifacts to be  
displayed in the picture. In the case of 480/720/1080 progressive scan  
picture problems, it is recommended that the user switch the  
connection to the ‘standard definition’ output. If there are questions  
regarding our TV set compatibility with this model 480p/720p/1080p  
Blu-ray Disc player, please contact our customer service center.  
• If the picture is not clear, natural, or to your satisfaction, change the  
video output resolution by pressing VIDEO FORMAT (page 46).  
• Be sure to use only an HDMI cord that bears the HDMI logo.  
Blu-ray Disc player  
COMPONENT  
VIDEO OUT  
VIDEO  
OUT  
VIDEO  
AUDIO  
OUT  
5.1CH OUTPUT  
FRONT REAR CENTER  
Y
P
P
DIGITAL OUT  
PCM/DTS/DOLBY DIGITAL  
AC IN  
L
L
COAXIAL  
OPTICAL  
B
R
HDMI  
OUT  
R
R
WOOFER  
S
VIDEO  
HDMI  
OUT  
to HDMI OUT  
HDMI cord  
(supplied with BDP-S301 only)  
About the ‘BRAVIA’ Theatre Sync  
features (for HDMI connections only)  
By connecting Sony components that are compatible with the  
HDMI Control function with an HDMI cord, operation is  
simplified as below:  
• One-Touch Play (page 21)  
TV, projector, or AV  
amplifier (receiver)  
You can turn on the player and TV/AV receiver, set the TV/AV  
receiver’s input to the player, and start playback with one touch  
of the H button.  
HDMI IN  
• System Power-Off  
This Blu-ray Disc player incorporates High-Definition  
Multimedia Interface (HDMI™) technology. HDMI, the HDMI  
logo and High-Definition Multimedia Interface are trademarks  
or registered trademarks of HDMI Licensing LLC.  
When you turn the TV off by using the POWER button on the  
TV’s remote, the HDMI compatible components turn off  
automatically.  
Notes on connecting to the HDMI OUT jack  
Observe the following as improper handling may damage the  
HDMI OUT jack and the connector.  
• Carefully align the HDMI OUT jack on the back of the player  
and the HDMI connector by checking their shapes. Make sure  
the connector is not upside down or tilted.  
To prepare for the ‘BRAVIA’ Theatre Sync  
features  
Set “HDMI Control” of “Options” setup to “On” (page 52).  
Note  
Depending on the connected component, the HDMI Control function  
may not work. Refer to the operating instructions supplied with the  
component.  
HDMI  
UT  
O
I
HDM  
OUT  
• Be sure to disconnect the HDMI cord when moving the player.  
• If you place the player on the cabinet with the HDMI cord  
connected, do not apply too much pressure to the cabinet wall.  
It may damage the HDMI OUT jack or the HDMI cord.  
• When connecting or disconnecting, do not screw in or rotate  
the HDMI connector.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Notes about the HDMI OUT jack  
• When you connect the player to an AV amplifier (receiver)  
using an HDMI cord, you will need to do one of the following:  
Connect the AV amplifier (receiver) to a TV with the HDMI  
cord.  
Step 3: Connecting the  
Audio Cords  
Connect the player to the TV with a video cord other than an  
HDMI cord (component video cord, S VIDEO cord, or video  
cord).  
• When connecting to the HDMI OUT jack, carefully align the  
HDMI connector with the jack. Do not bend or apply pressure  
to the HDMI cord.  
Select the connection that best suits your system. Be sure to read  
the instructions for the components you wish to connect.  
• If you change the component connected to the HDMI OUT  
jack, change “Audio (HDMI)” in “Audio Setup” to match the  
new component (page 47). The player stores the HDMI related  
settings for up to five components.  
• The HDMI connection is compatible with 2ch Linear PCM  
signals (48 to 192 kHz, 16/20/24 bit), and 6 to 8ch Linear PCM  
signals (48 to 96 kHz, 16/20/24 bit), in addition to Dolby  
Digital and DTS bit stream (5.1ch signals up to 96 kHz, 16/20/  
24bit).  
Connection  
Your setup  
A
TV  
B
Stereo amplifier (receiver) and  
two speakers  
Note  
If you connect a component that does not conform to the selected audio  
signal, a loud noise (or no sound) will come out from the speakers, which  
could damage your ears or speakers.  
C
AV amplifier (receiver) having a  
*1  
Dolby Surround (Pro Logic)  
decoder and 3 to 6 speakers  
• Surround effects: Dolby Surround  
(Pro Logic)  
D-1  
AV amplifier (receiver) with  
5.1ch input jacks and 6 speakers  
• Surround effects: Dolby Digital  
(5.1ch), DTS (5.1ch)  
D-2  
AV amplifier (receiver) with a  
digital input jack having a Dolby  
*2  
Digital or DTS decoder and 6  
speakers  
• Surround effects: Dolby Digital  
(5.1ch), DTS (5.1ch)  
D-3  
AV amplifier (receiver) with an  
HDMI input jack and 8 speakers  
• Surround effects: 8ch Linear  
PCM  
*1  
Manufactured under license from Dolby laboratories.  
“Dolby,” “Pro Logic,” and the double-D symbol are trademarks of  
Dolby Laboratories.  
“DTS” and “DTS Digital Surround” are registered trademarks of  
DTS, Inc.  
*2  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
B
A
Connecting to your TV  
Connecting to a stereo amplifier  
This connection will use your TV’s speakers for sound.  
(receiver) and 2 speakers  
If your stereo amplifier (receiver) only has audio input jacks L  
and R, use B-1 . If your amplifier (receiver) has a digital input  
jack, use B-2 .  
Blu-ray Disc player  
Blu-ray Disc player  
COMPONENT  
VIDEO OUT  
COMPONENT  
VIDEO OUT  
VIDEO  
OUT  
VIDEO  
VIDEO  
OUT  
VIDEO  
AUDIO  
OUT  
5.1CH OUTPUT  
FRONT REAR CENTER  
AUDIO  
OUT  
5.1CH OUTPUT  
FRONT REAR CENTER  
Y
P
P
Y
P
P
DIGITAL OUT  
DIGITAL OUT  
PCM/DTS/DOLBY DIGITAL  
PCM/DTS/DOLBY DIGITAL  
AC IN  
AC IN  
L
L
L
L
COAXIAL  
OPTICAL  
COAXIAL  
OPTICAL  
B
R
B
R
HDMI  
OUT  
HDMI  
OUT  
R
R
R
R
WOOFER  
WOOFER  
S
VIDEO  
S
VIDEO  
to AUDIO OUT L/R  
(white)  
AUDIO  
OUT  
AUDIO  
OUT  
B-2  
B-1  
L
DIGITAL OUT  
PCM/DTS/DOLBY DIGITAL  
COAXIAL  
OPTICAL  
L
R
R
(red)  
TV  
INPUT  
to DIGITAL OUT  
(COAXIAL or OPTICAL)  
to AUDIO OUT  
L/R  
Stereo audio cord  
(supplied)  
VIDEO  
(white)  
(red)  
L
(white)  
(white)  
(red)  
AUDIO  
Optical digital cord  
(not supplied)  
R
or  
Stereo audio  
cord (supplied)  
Coaxialdigital cord  
(not supplied)  
: Signal flow  
(red)  
to coaxial or optical  
digital input  
to audio input  
[Speakers]  
Front (L)  
Stereo amplifier (receiver)  
Front (R)  
: Signal flow  
,continued  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
C
D-1  
Connecting to an AV amplifier  
Connecting to an AV amplifier  
(receiver) having a Dolby Surround (Pro  
Logic) decoder and 3 to 6 speakers  
If your AV amplifier (receiver) only has L and R audio input  
jacks, use C-1 . If your amplifier (receiver) has a digital input  
jack, use C-2 .  
(receiver) with 5.1ch input jacks and 6  
speakers  
If your AV amplifier (receiver) has 5.1 channel inputs, use  
D-1 .  
You can enjoy surround effects only when playing Dolby  
Surround audio or multi-channel audio (Dolby Digital or DTS)  
discs.  
Blu-ray Disc player  
Blu-ray Disc player  
COMPONENT  
VIDEO OUT  
COMPONENT  
VIDEO OUT  
VIDEO  
OUT  
VIDEO  
VIDEO  
OUT  
VIDEO  
AUDIO  
OUT  
5.1CH OUTPUT  
FRONT REAR CENTER  
AUDIO  
OUT  
5.1CH OUTPUT  
Y
P
P
Y
P
P
FRONT  
REAR  
CENTER  
DIGITAL OUT  
DIGITAL OUT  
PCM/DTS/DOLBY DIGITAL  
PCM/DTS/DOLBY DIGITAL  
AC IN  
AC IN  
L
L
L
L
COAXIAL  
OPTICAL  
COAXIAL  
OPTICAL  
B
R
B
R
HDMI  
OUT  
HDMI  
OUT  
R
R
R
R
WOOFER  
S
VIDEO  
WOOFER  
S
VIDEO  
AUDIO  
OUT  
D-1  
C-2  
C-1  
DIGITAL OUT  
5.1CH OUTPUT  
PCM/DTS/DOLBY DIGITAL  
FRONT  
REAR  
CENTER  
COAXIAL  
OPTICAL  
L
L
R
WOOFER  
to DIGITAL OUT  
(COAXIAL or OPTICAL)  
to AUDIO OUT  
L/R  
to 5.1CH  
OUTPUT  
(white)  
(red)  
Optical digital cord  
(not supplied)  
or  
Stereo audio  
cord (one is  
supplied)  
Monaural  
audio cord  
(not supplied)  
Stereo audio  
cord (supplied)  
Coaxial digital cord  
(not supplied)  
(white)  
(red)  
to audio input  
[Speakers]  
to coaxial or optical  
digital input  
to audio input  
[Speakers]  
[Speakers]  
[Speakers]  
AV amplifier  
(receiver) with  
5.1ch inputs  
AV Amplifier  
(receiver) with a  
decoder  
Rear (L)  
Rear (R)  
Center  
Front (R)  
Rear (L) Rear (R)  
Front (R)  
Center  
Front (L)  
Subwoofer  
: Signal flow  
Front (L)  
Subwoofer  
Rear (mono)  
: Signal flow  
z Hint  
z Hint  
For correct speaker location, see the operating instructions of the  
connected components.  
For correct speaker location, see the operating instructions of the  
connected components.  
Note  
When connecting 6 speakers, you do not need the “Rear (mono)” speaker  
above.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
D-2  
D-3  
Connecting to an AV amplifier  
Connecting to an AV amplifier  
(receiver) with a digital input jack and  
6 speakers  
If you want to use the Dolby Digital, or DTS decoder function  
on your AV amplifier (receiver), connect to its digital jack using  
(receiver) with an HDMI input jack and  
8 speakers  
If your AV amplifier (receiver) accepts 8ch Linear PCM input  
with an HDMI connection, you can enjoy the surround sound  
. You can enjoy a more realistic audio presence.  
using  
.
D-2  
D-3  
Blu-ray Disc player  
Blu-ray Disc player  
COMPONENT  
VIDEO OUT  
COMPONENT  
VIDEO OUT  
VIDEO  
OUT  
AUDIO  
OUT  
5.1CH OUTPUT  
FRONT REAR CENTER  
VIDEO  
OUT  
AUDIO  
OUT  
5.1CH OUTPUT  
FRONT REAR CENTER  
Y
Y
DIGITAL OUT  
VIDEO  
DIGITAL OUT  
PCM/DTS/DOLBY DIGITAL  
VIDEO  
PCM/DTS/DOLBY DIGITAL  
AC IN  
L
L
COAXIAL  
OPTICAL  
AC IN  
L
L
P
B
R
COAXIAL  
OPTICAL  
P
B
R
HDMI  
OUT  
P
HDMI  
OUT  
R
R
P
R
R
WOOFER  
S
VIDEO  
WOOFER  
S
VIDEO  
D-2  
D-3  
DIGITAL OUT  
PCM/DTS/DOLBY DIGITAL  
COAXIAL  
OPTICAL  
HDMI  
OUT  
HDMI  
OUT  
to HDMI OUT  
to DIGITAL OUT  
(COAXIAL  
to HDMI OUT  
or OPTICAL)  
Coaxial digital cord  
(not supplied)  
HDMI cord  
(supplied with  
BDP-S301 only)  
or  
or  
HDMI cord  
(supplied with  
BDP-S301 only)  
Optical digital cord  
(not supplied)  
to HDMI input  
[Speakers]  
to coaxial or optical  
digital input  
to HDMI input  
[Speakers]  
[Speakers]  
[Speakers]  
AV amplifier  
AV amplifier  
(receiver) having a  
decoder  
(receiver) with 8ch  
outputs  
Rear (L)  
Center  
Rear1 (L)  
Center  
Subwoofer  
Rear (R)  
Rear1 (R) Rear2 (R)  
Rear2 (L)  
Front (R)  
Front (R)  
Subwoofer  
: Signal flow  
Front (L)  
Front (L)  
z Hint  
z Hint  
For correct speaker location, see the operating instructions of the  
connected components.  
For correct speaker location, see the operating instructions of the  
connected components.  
Note  
Not all HDMI-compatible AV amplifiers (receivers) accept 8ch Linear  
PCM signals. See also the operating instructions supplied with the  
connected AV amplifier (receiver).  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Step 4: Connecting the  
Power Cord  
Step 5: Preparing the  
Remote  
After all of the other connections are complete, connect the  
supplied power cord to the AC IN terminal of the player. Then  
plug the player and TV power cords into the AC outlet.  
You can control the player using the supplied remote. Insert two  
Size AA (R6) batteries by matching the 3 and # ends on the  
batteries to the markings inside the battery compartment. When  
using the remote, point it at the remote sensor on the player  
AC IN  
to AC IN  
to AC outlet  
Notes  
• Do not leave the remote in an extremely hot or humid place.  
• Do not drop any foreign object into the remote casing, particularly  
when replacing the batteries.  
• Do not expose the remote sensor to direct sunlight or a lighting  
apparatus. Doing so may cause a malfunction.  
• If you do not use the remote for an extended period of time, remove the  
batteries to avoid possible damage from battery leakage and corrosion.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
To control other TVs with the remote  
If you want to control your TV with the  
supplied remote  
You can control the volume, input source, and power switch of  
your Sony TV with the supplied remote.  
You can control the volume, input source, and power switch of non-  
Sony TVs as well.  
If your TV is listed in the table below, set the appropriate  
manufacturer’s code.  
1
While holding down TV [/1, press the number  
buttons to select your TV manufacturer’s code  
(see the table below).  
OPEN/  
CLOSE  
TV  
TV \/1  
DIMMER DISPLAY TV/VIDEO  
TV/VIDEO  
2
Release TV [/1.  
1
4
2
5
8
0
3
6
9
Number  
buttons  
Code numbers of controllable TVs  
If more than one code number is listed, try entering them one at  
a time until you find the one that works with your TV.  
7
VIDEO  
FORMAT  
CLEAR  
AUDIO  
SUBTITLE ANGLE  
Manufacturer  
Sony  
Code number  
01 (default)  
22, 04  
14  
RED GREEN BLUE YELLOW  
SYSTEM  
TOP  
MENU  
MENU  
Daewoo  
Emerson  
GE  
06  
POP UP/  
MENU  
Hitachi  
02, 04  
09  
RETURN  
PREV  
SLOW/STEP  
PLAY  
NEXT  
JVC  
SCAN  
SCAN  
LG/Gold star  
MGA/Mitsubishi  
NEC  
03, 17, 04  
13, 04  
04, 12  
19  
PAUSE  
STOP  
PLAY MODE  
VOL  
CH  
MUTING  
Panasonic  
Philips  
CH +/–  
MUTING  
VOL +/–  
08, 21  
16  
Pioneer  
RCA  
10, 04  
05  
R.Shack  
Samsung  
Sanyo  
04, 12, 20  
11  
Sharp  
05, 18  
07, 18  
15  
Toshiba  
Zenith  
By pressing  
You can  
TV [/1  
Turn the TV on or off.  
To return the remote to its default settings  
VOL +/–  
TV/VIDEO  
Adjust the volume of the TV.  
1
2
Remove the batteries from the remote.  
Switch the TV’s input source between the  
TV and other input sources.  
Re-insert the batteries while pressing down 1, 2,  
and 3 of the number buttons.  
CH +/–  
Select the channel up and down.  
Mute the sound (for Sony TV only).  
MUTING  
3
Wait for a few seconds.  
Note  
Depending on the connected unit, you may not be able to control your  
TV using all or some of the buttons on the supplied remote.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
e Select “Start,” and press ENTER to start  
“Easy Setup.”  
Step 6: Easy Setup  
Easy Setup  
Before using, make some simple  
settings for the BD player.  
Start  
Cancel  
Follow the steps below to make the minimum number of basic  
adjustments for using the player. If you do not complete Easy  
Setup, it will appear each time you turn on your player.  
Make the settings below in the following order.  
Please use the Initial Setup if you  
want to make more detailed settings.  
When turned on for the first time  
Wait about 90 seconds before the player turns on and starts  
Easy Setup. The start-up time will be much shorter once Easy  
Setup is completed.  
If the above display does not appear  
Go to step 6. This display appears only when the player is turned  
on for the first time.  
f Select the video output format for the  
connected TV, and press ENTER.  
OPEN/  
CLOSE  
TV  
For details about the video output, see page 46.  
"/1  
When using the HDMI OUT jack  
DIMMER DISPLAY TV/VIDEO  
1
4
2
5
8
0
3
6
9
Easy Setup  
Output Video Format  
7
VIDEO  
FORMAT  
Auto  
CLEAR  
480i  
480p  
AUDIO  
SUBTITLE ANGLE  
720p  
1080i  
RED GREEN BLUE YELLOW  
1080p  
Source Direct  
SYSTEM  
MENU  
TOP  
MENU  
</M/m/,,  
ENTER  
Select from “Auto,” “480i,” “480p,” “720p,”  
“1080i,” “1080p,” or “Source Direct,” then go to  
step 8. “TV Type” in step 7 will be set to “16:9”  
(wide screen).  
POP UP/  
MENU  
RETURN  
PREV  
SLOW/STEP  
NEXT  
When using the jacks other than the HDMI OUT  
a Turn on the TV.  
jack  
b Press [/1 to turn on the player.  
Easy Setup  
The player turns on after a moment.  
Output Video Format  
S-Video/Video only  
480i  
480p  
720p  
c Switch the input selector on your TV so that  
the signal from the player appears on your  
TV screen.  
1080i  
Don't Know  
If the display for OSD language selection does not  
appear, select “Start” of “Easy Setup” in “Options”  
Setup (page 52).  
Select from “S-Video/Video only,” “480i,”  
“480p,” “720p,” “1080i” or “Don’t Know.” If  
you select “720p” or “1080i,” go to step 8. “TV  
Type” in step 7 will be set to “16:9” (wide  
screen).  
d Select the OSD language you want to display,  
and press ENTER.  
Easy Setup  
Language  
English  
Français  
This will determine the Audio, Subtitle and BD/  
DVD menu languages as well.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
g Select the aspect ratio that matches your TV,  
and press ENTER.  
Step 7: Additional  
Adjustments  
Easy Setup  
TV Type  
16:9  
4:3  
The following settings and adjustments are necessary when your  
connection applies.  
For video connection  
When using the COMPONENT VIDEO OUT jacks  
(Pattern C page 10)  
• Select the video output resolution for your TV by pressing  
VIDEO FORMAT (page 46).  
If you have a wide screen TV or a 4:3 standard TV  
with a wide screen mode  
Select “16:9” (page 45).  
When using the HDMI OUT jack  
(Pattern D page 11)  
If you have a 4:3 standard TV  
• Select the video output resolution for your TV by pressing  
VIDEO FORMAT (page 46).  
Select “4:3” (page 45).  
• Select the type of video output from the HDMI OUT jack in  
“YCbCr/RGBPC (HDMI)” of “Video Setup” (page 45).  
h Select “Finish Setup,” and press ENTER.  
Easy Setup  
For audio connection  
When using the DIGITAL OUT (OPTICAL or COAXIAL) jack  
Setup is complete!  
Enjoy using your BD player!  
Finish Setup  
Go Back  
(Connection B-2 , C-2 ,  
page 13 to 15)  
D-2  
• Set “Dolby Digital” and “DTS” in “Audio Setup” (page 47)  
according to your AV amplifier’s (receiver’s) decoder.  
When using the HDMI OUT jack  
(HDMI connection of  
,
page 15)  
D-2  
D-3  
• Set “Dolby Digital” and “DTS” in “Audio Setup” (page 47)  
according to your AV amplifier’s (receiver’s) decoder.  
• Select the audio output method from the HDMI OUT jack in  
“Audio (HDMI)” of “Audio Setup” (page 47).  
z Hints  
When using the AUDIO OUT (L/R) jacks  
(Connection C-1 page 14)  
• Set “DTS Downmix” to “Lt/Rt” in “Audio Setup” (page 47).  
• If you want to reset these settings to their factory defaults, see  
• You can re-run “Easy Setup” from “Options” Setup (page 52).  
When using the 5.1CH OUTPUT jacks  
(Connection  
page 14)  
D-1  
• Set “Audio Output Mode” to “5.1 Channel” in “Speakers”  
Setup (page 51), and adjust the “Speaker Setup” setting for  
your system.  
Notes  
• If you connect a component that does not conform to the selected audio  
signal, a loud noise (or no sound) will come out from the speakers,  
which could damage your ears or speakers.  
• If you connect using the HDMI OUT jack or COMPONENT VIDEO  
OUT jacks and the picture does not appear clearly, the connected  
display device may not be compatible with the progressive signals. In  
this case, connect the display device to the S VIDEO jack or the  
VIDEO jack (pattern A or B – see page 10), re-run the “Easy Setup”  
from the “Options” Setup (page 52), and select “S-Video/Video only”  
in step 6 (page 18). Also, check the above items again to see if any  
additional adjustment is required.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Playing a Disc  
Basic  
BD  
DVD  
CD  
Operations  
OPEN/  
CLOSE  
TV  
Z
\/1  
Most of the BD playback operations are  
common to DVD. This section covers BD/  
DVD/CD playback in general, together with  
the basic operation of the player.  
DIMMER DISPLAY TV/VIDEO  
1
4
2
5
8
0
3
6
9
Number buttons  
7
VIDEO  
FORMAT  
CLEAR  
For browsing recorded files on DATA  
DVDs*, a separate library function is  
available. See also page 32 for movie, 36 for  
music, 40 for photo files.  
For operations using the remote, a complete  
list is located on page 24.  
AUDIO  
SUBTITLE ANGLE  
RED GREEN BLUE YELLOW  
Color buttons  
SYSTEM  
MENU  
TOP  
MENU  
SYSTEM MENU  
RETURN  
TOP MENU  
</M/m/,, ENTER  
POP UP/MENU  
POP UP/  
MENU  
RETURN  
PREV  
*
DVD+RWs/DVD+Rs/DVD-RWs/DVD-Rs containing  
MPEG-2 PS movie, MP3 audio, or JPEG image files.  
SLOW/STEP  
PLAY  
NEXT  
SCAN  
SCAN  
H
x
PAUSE  
STOP  
PLAY MODE  
X
VOL  
CH  
MUTING  
a Press \/1.  
The player turns on after a moment.  
b Switch the input selector on your TV so that  
the signal from the player appears on your  
TV screen.  
c Press Z to open the disc tray.  
d Place a disc on the disc tray with the playback  
side facing down.  
Playing a Disc. . . . . . . . . . . . . . . . . . . . . . . . . 20  
Guide to Displays . . . . . . . . . . . . . . . . . . . . . . 22  
Guide to the Remote. . . . . . . . . . . . . . . . . . . . 24  
Checking the Disc Information . . . . . . . . . . . . 26  
Adjusting the Pictures . . . . . . . . . . . . . . . . . . 28  
Locking a Disc . . . . . . . . . . . . . . . . . . . . . . . . 29  
Playback side facing down  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
e Press Z to close the disc tray.  
Wait a short while until the disc type appears on the  
front panel display.  
About the screen saver function  
To prevent damage to your display device (ghosting), a screen  
saver image appears when the player is left unattended, has no  
disc inserted, or no title/slideshow is displayed for 15 minutes.  
To cancel, press any button on the remote or the player.  
f Press H to start playback.  
For more information about the remote’s operations,  
see page 24.  
About One-Touch Play (for HDMI connections  
only)  
Buttons  
Details  
With one touch of the H button, the player and your TV/AV  
receiver automatically turn on and the TV/AV receiver’s input is  
switched to the player. Playback starts automatically. To use this  
function, set “HDMI Control” of “Options” setup to “On”  
X
Pauses playback, or restarts playback from the same  
point.  
x
Stops playback, or cancels the resume point when  
pressed twice.  
The TV/AV receiver’s input will also switch to the player  
automatically, in the following cases:  
H
Starts or restarts playback from the previous stop  
point.  
You press H, SYSTEM MENU, TOP MENU, or POP UP/  
MENU buttons on the remote.  
–A disc with auto playback function is loaded.  
g When you finish playing, press Z to open the  
disc tray.  
h Remove the disc, and press Z again to close  
the disc tray.  
i Press \/1 to turn off the player.  
To use the BD’s or DVD’s menu  
When you play a BD-ROM, DVD VIDEO, or a finalized  
DVD+RW, DVD-RW (Video mode), DVD+R, or DVD-R  
(Video mode), you can display the disc’s menu by pressing TOP  
MENU or POP UP/MENU. Some BDs/DVDs display the menu  
automatically. Either cases, navigate through the menu using  
</M/m/,, ENTER, or the number buttons and the color  
buttons as indicated by the disc’s on-screen instructions. The BD  
menu is operable without interrupting playback.  
To play restricted BDs  
If “CAN’T PLAY” appears on the front panel display for a BD-  
ROM, change the “BD Parental Control” setting (page 30).  
To play restricted DVDs  
For a restricted DVD, the display asks for the password. For  
“DVD Parental Control” setting, see page 30.  
1
2
Enter your four-digit password using the number  
buttons.  
Press ENTER to confirm.  
To register or change the password, see page 29.  
Notes about Resume Play  
• Playback starts from the beginning if the title has not been  
played or the previous stop point is canceled.  
• The stop point is canceled when:  
you change the settings on the player.  
you turn off the player (BD-ROM and CD only).  
you press x twice.  
you open the disc tray.  
you finish a search.  
• The player remembers the stop point for one title/track/file  
only. On a music CD, playback resumes from the beginning of  
the track.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Title List  
For DATA DVDs, this display leads further to the Title Lists of  
content type. The three Title Lists appear similar and are  
operable in a similar way.  
Guide to Displays  
Title List  
BD  
DVD  
DATA DVD  
CD  
Movies  
Photos  
Music  
When ‘Select an item, and press ENTER’ appears in this manual,  
press the </M/m/, keys on the remote to select the item then  
the entry button in the middle. You can operate the player  
likewise using displays.  
System Menu  
Select the Title List you want to view; from “Movies,” “Photos,”  
or “Music,” and press ENTER.  
Title List  
A/V Control  
Setup  
Movies  
Displays movies/video titles only (page 32).  
Photos  
Displays image files only (page 40).  
Music  
Displays music files only (page 36).  
A/V Control (page 27)  
a Press SYSTEM MENU to turn on the above  
“System Menu.”  
Adjusts the audio/video settings. Select either “Video Control,”  
or “Audio Control,” and press ENTER.  
The player’s start menu appears, with entries to all of  
the functions.  
A/V Control  
b Select an item, and press ENTER.  
Each item leads to the following function displays.  
See the pages in parentheses for operations. When  
you want to return to the previous display, press  
RETURN.  
Video Control  
Audio Control  
Enters the Setup displays for changing the player’s settings.  
Select the related Setup display, and press ENTER.  
Setup  
Video Setup  
Audio Setup  
Language  
TV Type  
16:9  
4:3 Video Output  
DVD Aspect Ratio  
YCbCr/RGBPC(HDMI)  
24p Output  
Normal  
Letter Box  
Y, Cb, Cr  
Off  
Parental Control  
Speakers  
Options  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Entering characters  
DATA DVD  
When an on-screen keyboard appears (e.g., when searching for a  
title), enter the characters as follows.  
s_  
A
K
B C D E F G H  
L M N O P Q R S  
I
J
T
;
U V W X  
1
_
Y
5
Z
6
,
7
.
8
:
9
2
3
(
4
)
0
SHFT  
SPC  
DEL  
CLR  
DONE  
CANCEL  
a Select the character you want to enter, and  
press ENTER.  
The character appears in the entry field. If necessary,  
select the following items, and press ENTER.  
Items  
Details  
SHFT  
Switches between upper and lower case  
characters. Select this before entering the  
character.  
SPC  
DEL  
CLR  
Inserts a space.  
Deletes the last character input.  
Clears all input characters.  
b Repeat step 1 to complete the entry.  
c Select “DONE,” and press ENTER to close  
the on-screen keyboard.  
Note  
You cannot use the extended character set.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
A Z OPEN/CLOSE (page 20)  
Guide to the Remote  
– Opens/closes the disc tray.  
– Turns the TV on or to standby mode.  
The following covers all of the remote’s functions. Refer to the  
list when necessary.  
– Turns on, or sets the player to standby mode.  
B DIMMER (page 59)  
– Changes the brightness of the front panel display  
on the player (when completely darkened,  
indicators on the front panel are also turned off  
and the FL OFF indicator lights up).  
OPEN/  
CLOSE  
TV  
DIMMER DISPLAY TV/VIDEO  
DISPLAY (page 26)  
– Displays the disc information on the screen.  
1
4
2
5
8
0
3
6
9
TV/VIDEO (page 17)  
– Switches between TV and other input sources.  
C Number buttons (page 26)  
7
VIDEO  
FORMAT  
– Enters the title/chapter numbers, etc.  
CLEAR  
CLEAR  
– Clears the entry field.  
AUDIO  
SUBTITLE ANGLE  
RED GREEN BLUE YELLOW  
D VIDEO FORMAT (page 45)  
– Changes the video output resolution from the  
HDMI OUT jack and the COMPONENT VIDEO  
OUT jacks. Press this button repeatedly if no  
picture appears.  
SYSTEM  
MENU  
TOP  
MENU  
E AUDIO*1 (page 49)  
– Selects the sound track or the language track on a  
BD/DVD.  
1
*
When playing MPEG-2 movie files or MP3 music files on a  
DATA DVD, or a music CD, you cannot select the left or  
right channel only.  
POP UP/  
MENU  
RETURN  
PREV  
SLOW/STEP  
PLAY  
NEXT  
SUBTITLE (page 49)  
– Selects the subtitle language on a BD/DVD.  
SCAN  
SCAN  
PAUSE  
STOP  
ANGLE  
PLAY MODE  
– Switches to other viewing angles when available.  
VOL  
CH  
F Color buttons (RED/GREEN/BLUE/YELLOW)  
– Short cut keys for selecting items on some BD’s  
menus (can also be used for BD’s Java interactive  
operations).  
MUTING  
Number 5, AUDIO, CH+, and H buttons have a tactile dot. Use the  
tactile dot as a reference when operating the player.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
G SYSTEM MENU (page 22)  
– Enters/exits the player’s start menu (“System  
Menu”).  
I For TVs operable with the following buttons, see  
TOP MENU (page 20)  
– Mutes the TV sound.  
– Opens/closes the BD’s or DVD’s top menu.  
VOL (volume) +/– (page 17)  
POP UP/MENU (page 20)  
– Adjusts the TV volume.  
– Opens/closes the BD’s pop up menu, or the  
DVD’s disc menu.  
CH (channel) +/– (page 17)  
– Selects the TV channels up and down.  
RETURN (page 20, 22)  
– Returns to the previous display.  
Playing in various play mode  
</M/m/, (page 20, 22)  
– Moves the highlight to select a displayed item.  
BD  
DVD  
DATA DVD  
CD  
Center button (ENTER) (page 20, 22)  
– Enters the selected item.  
a During playback, press PLAY MODE  
repeatedly.  
H ./> PREV/NEXT  
Available items differ depending on the current title/  
track/file or the disc type. To cancel the Play Mode,  
press PLAY MODE again. For “Time Search,” see  
– Skips to the previous/next chapter, track, or file.  
c/ C SLOW/STEP*2  
– Plays in slow motion or stop motion. To return to  
normal play, press H.  
When playing a video or movie title  
• To play in slow motion  
Items  
Details  
Press  
play starts, press  
C during playback. When slow motion  
C repeatedly to change the  
Repeat Chapter  
(BD-ROM/DVD VIDEO  
only)  
Repeats the current chapter.  
speed : 1/16 t 1/8 t 1/4 t 1/2 of normal playback  
speed.  
Repeat Title  
Repeats the current title.  
• To play in stop motion (step by step)  
Press X during playback, then press c or  
C
repeatedly.  
When playing a music track  
m/M SCAN*2  
Items  
Details  
– Scans backwards or forward. The speed changes  
when pressed repeatedly.  
Repeat Track  
Repeat All  
Repeats the current track.  
Repeats all the tracks on the disc or the  
“Music” Title List.  
2
*
Depending on the disc or file type, the function may not work  
or the scan speeds may differ.  
Random  
Plays all the tracks on the disc or the  
“Music” Title List in a random order.  
H PLAY  
– Starts or re-starts playback.  
When playing a photo image  
Items  
Details  
PLAY MODE  
Repeat All  
Repeats all the files on the disc or  
“Photos” Title List.  
– Switches to other play modes (Repeat Play, etc.)  
when pressed during playback.  
– Searches for a specific point (page 26).  
Random  
Plays all the files on the disc or “Photos”  
Title List in a random order.  
X PAUSE  
– Pauses/re-starts playback.  
x STOP  
– Stops playback.  
– Clears the resume point when pressed twice. The  
resume point for a title is the last point you  
played, the last track for an audio file, or the last  
photo for a photo file.  
,continued  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Searching using the remote  
Checking the Disc  
Information  
BD  
DVD  
DATA DVD  
You can search by entering the title/chapter number or the time  
code (elapsed time from the beginning of the disc).  
BD  
DVD  
DATA DVD  
CD  
OPEN/  
CLOSE  
TV  
You can check the title/chapter/track information including  
video transmission rate etc., by pressing DISPLAY. The  
information differs depending on the disc type and the player  
status.  
DIMMER DISPLAY TV/VIDEO  
1
4
2
5
8
0
3
6
9
Number buttons  
7
VIDEO  
FORMAT  
CLEAR  
a Press DISPLAY.  
AUDIO  
SUBTITLE ANGLE  
RED GREEN BLUE YELLOW  
Example: When playing a DVD VIDEO.  
SYSTEM  
MENU  
TOP  
MENU  
ENTER  
Play  
DVD-VIDEO  
1-1 2.01.23  
Chapters 12  
Title Total  
Repeat Title  
2h15m34s  
POP UP/  
MENU  
RETURN  
PREV  
SLOW/STEP  
PLAY  
NEXT  
SCAN  
SCAN  
PAUSE  
STOP  
PLAY MODE  
PLAY MODE  
VOL  
CH  
MUTING  
The following information appears:  
1 Playback status  
2 Disc type  
3 Title information  
• Currently playing title number/currently playing  
chapter number.  
• Total number of chapters within the title.  
• Total playback time of the title.  
To search for a title or chapter (BD-ROM, DVD  
VIDEO only)  
4 Elapsed time of the current title  
5 Play mode  
1
Enter the title number using the number buttons  
while the player is in stop mode.  
To search for a chapter, enter the chapter number  
during playback. If you make a mistake, press  
CLEAR once and re-enter.  
b Press DISPLAY again.  
2
Press ENTER to start playback.  
Play  
DVD-VIDEO  
1-1 2.01.23  
Chapter Time  
Chapter Total  
Repeat Title  
01.11.56  
2h15m34s  
10.03 Mbps  
To search for a specific point  
1
During playback, press PLAY MODE repeatedly  
until “Time Search” appears.  
2
Enter the time code using the number buttons.  
Enter the time in minutes and seconds (e.g., ‘12030’  
for 1 hour, 20 minutes and 30 seconds). If you make  
a mistake, press CLEAR once and re-enter.  
The display switches to show the following  
information:  
3
Press ENTER to start playback.  
1 Chapter information  
Note  
• Elapsed time of the current chapter.  
• Total playback time of the current chapter.  
Depending on the DVD VIDEO/BD-ROM/DATA DVD, these search  
functions may not work.  
2 Video transmission rate and the stream  
information  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
z Hints  
• You can check disc information also on the front panel display  
(page 59) or the Title List display (page 22).  
• You can check the audio information by pressing AUDIO.  
Clarifying Low Volume  
Sounds (Audio DRC)  
BD  
DVD  
DATA DVD  
Even at low volume, you can make low sounds such as dialogs  
more audible.  
Audio Control  
Audio DRC  
Off  
Max  
Convenient when you cannot turn up the volume (e.g., at  
night)  
a Press SYSTEM MENU during playback.  
b Select “A/V Control,” and press ENTER.  
c Select “Audio Control,” and press ENTER to  
turn on the above display.  
d While “Audio DRC” is highlighted, select  
from “Max” to “Off” by pressing </,.  
e Press ENTER.  
Note  
“Audio DRC” is effective only when the disc is a Dolby Digital Blu-ray  
Disc or DVD, and:  
– “Dolby Digital” in “Audio Setup” is set to “Downmix PCM” (page 47)  
and the audio signals are output from the DIGITAL OUT (OPTICAL  
or COAXIAL) jack or the HDMI OUT jack.  
– “Audio (HDMI)” in “Audio Setup” is set to “PCM” (page 47) and the  
audio signals are output from the HDMI OUT jack.  
– the audio signals are output from the AUDIO OUT (L/R) jacks or the  
5.1CH OUTPUT jacks.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Fine-tuning the picture to your  
preference  
Adjusting the Pictures  
Memory1  
Min  
Min  
Max  
Max  
Red  
Max  
White Adjust  
Black Adjust  
Hue  
BD  
DVD  
DATA DVD  
Green  
Min  
Color Level  
The “cinema tuned” picture preset setting will allow you to  
maximize the visual impact of the BD or DVD you are watching  
by optimizing the picture settings for different lighting  
environments. “Memory” allows you to make your own detailed  
adjustments.  
a Select from “Memory 1” to “Memory 3” in  
step 4 of “Adjusting the Pictures(page 28).  
b Select “Detailed Settings,” and press ENTER  
to turn on the above display.  
To switch to another “Memory,” press RETURN.  
c Select each of the picture elements, and  
Standard  
adjust using </,.  
Detailed Settings  
To adjust while previewing the effect  
Select a setting and press ENTER to switch the  
display for the setting. Press </, to adjust  
while checking the effect on the background  
playback picture. Then press ENTER to save the  
adjustment.  
a Press SYSTEM MENU during playback.  
b Select “A/V Control,” and press ENTER.  
Underlined are the default settings for “Memory.”  
c Select “Video Control,” and press ENTER to  
turn on the above display.  
Items  
Details  
White Adjust  
(Min~(mid)~Max)  
Adjusts the brightness of white  
colors.  
d Press </, to select a setting.  
Black Adjust  
Adjusts the richness of dark colors.  
Items  
Details  
(Min~(mid)~Max)  
Brighter Room  
Theater Room  
For a room brighter than normal.  
Hue  
Balances the green and the red  
colors.  
(Green~(mid)~Red)  
For a dark room such as a home  
theater.  
Color Level  
Adjusts the color saturation.  
(Min~(mid)~Max)  
Standard (default)  
Memory (1-3)  
Normally, select this.  
Select a setting when you want to  
use the detailed picture adjustments  
you previously made, or when you  
want to make a new set. The player  
remembers up to three sets (see  
page 28).  
d Press RETURN.  
e Press ENTER.  
z Hint  
The above description applies when the picture setting of your TV (if  
any) is set to ‘Standard.’  
Note  
“Memory” settings do not affect the output from the S VIDEO OUT or  
VIDEO OUT jacks.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Setting/changing the password  
Locking a Disc  
BD  
DVD  
Setup  
BD  
DVD  
Video Setup  
Change Password  
Next Screen  
Next Screen  
Next Screen  
Audio Setup  
Language  
DVD Parental Control  
BD Parental Control  
Parental Control  
Speakers  
By setting the password and your limit in “Parental Control”  
Setup, you can control playback of inappropriate discs.  
Options  
BD PLAYER  
Parental Control  
Use the number keys to  
enter the password to  
turn off the parental  
lock.  
a Press SYSTEM MENU.  
Current Level  
Disc Level  
3
5
b Select “Setup,” and press ENTER.  
c Select “Parental Control,” and press ENTER  
to turn on the above “Parental Control”  
Setup.  
The password is required when the DVD exceeds the  
level you set.  
d Select “Change Password (Set Password),”  
Notes  
and press ENTER.  
• You cannot limit playback if the DVD VIDEO/BD-ROM does not  
have the “Parental Control” function.  
• If you forget the password, you will have to return all of the player  
settings to their factory defaults (page 53).  
• The above display does not appear for BD-ROM. If you cannot play a  
BD-ROM because of Parental Control, reset “Change Age Restriction”  
of “BD Parental Control” (page 50).  
e Select “Next Screen,” and press ENTER to  
turn on the password display.  
When you have not yet registered a password  
Enter a four-digit password using the number  
buttons, and press m. Re-enter it for  
confirmation, and press ENTER.  
When you have already registered a password  
Enter the four-digit password using the number  
buttons, and press ENTER. Enter a new password  
and press m, then re-enter it for confirmation, and  
press ENTER.  
z Hint  
To continue to set “DVD Parental Control,” go to step 4 of “Setting the  
,continued  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Setting the Parental Control for DVD  
VIDEOs  
Setting the Parental Control for BD-  
ROMs  
DVD  
BD  
Setup  
Setup  
Change Level  
Change Age Restriction  
Video Setup  
Audio Setup  
Language  
Video Setup  
Audio Setup  
Language  
Password  
Level  
Password  
Parental Control  
Speakers  
Parental Control  
Speakers  
Age Restriction  
Off  
255  
Options  
Options  
a Press SYSTEM MENU.  
a Press SYSTEM MENU.  
b Select “Setup,” and press ENTER.  
b Select “Setup,” and press ENTER.  
c Select “Parental Control,” and press ENTER  
c Select “Parental Control,” and press ENTER  
to turn on the “Parental Control” Setup.  
to turn on the “Parental Control” Setup.  
d Select “DVD Parental Control,” and press  
d Select “BD Parental Control,” and press  
ENTER.  
ENTER.  
e Select “Change Level,” and press ENTER to  
turn on the above display.  
e Select “Change Age Restriction,” and press  
ENTER to turn on the above display.  
For BD-ROMs, the restriction is set by age, not by  
level.  
This will set the playback limitation level.  
f Enter the password using the number  
f Enter the password using the number  
buttons, and press ENTER.  
buttons, and press ENTER.  
g Press </, to select the limitation level  
from “Off” to “Level 8,” and press ENTER.  
Note that the lower the value, the stricter the  
limitation.  
g Press </, to select the age from “0” to  
“255,” and press ENTER.  
h When the display returns to the “Parental  
Control” Setup, select “BD Parental  
Control,” and press ENTER.  
h When the display returns to the “Parental  
Control” Setup, select “DVD Parental  
Control,” and press ENTER.  
i Select “BD Country Code,” and press  
ENTER.  
i Select “DVD Country Code,” and press  
ENTER.  
This ensures that you see the scenes intended for  
This ensures that you see the scenes intended for  
your residential area.  
your residential area.  
j On the “BD Country Code” display, enter the  
password using the number buttons, and  
press ENTER.  
j On the “DVD Country Code” display, enter  
the password using the number buttons, and  
press ENTER.  
k Press </, to select your country code (see  
page 69), or press m and enter the code for  
your area using the number buttons.  
k Press </, to select your country code (see  
page 69), or press m and enter the code for  
your area using the number buttons.  
l Press ENTER.  
l Press ENTER.  
z Hint  
To continue to set “BD Parental Control,” go to step 4 of “Setting the  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Viewing All Titles  
Watching Movie  
Files  
DATA DVD  
The “Movies” Title List first displays all titles on the disc.  
All Movies  
1214 items  
Use the “Movies” Title List to browse  
through and sort MPEG-2 PS movie files on  
DATA DVDs.  
Spider  
Smoother  
Sideway  
Home  
Alpinist  
Electricity  
Lemon Grove  
Bridget  
All Movies  
Browse  
Search  
Sort  
Finding Never-Ever Land  
Meet My Mom  
The Browse menu appears when you press <  
a Press SYSTEM MENU.  
b Select “Title List,” and press ENTER.  
c Select “Movies,” and press ENTER.  
The above “All Movies” display appears, showing  
all titles (scrollable by pressing m). From “All  
Movies” you can apply items to all titles using the  
Browse menu (see below).  
To use the Browse menu  
Press < after step 3 to display the items for the “Movies” Title  
List. For operations, see the pages in parentheses. Available  
items differ depending on the display.  
Items  
Details  
All Movies  
Browse  
Lists all titles (as above).  
Displays a list of genres, Quicklist, or  
folders (page 34).  
Search  
Sort  
Searches for a title using the on-screen  
keyboard (page 34).  
Reorders the titles by date or alphabet (see  
below).  
Example: To apply “Sort” to all titles  
A Select “Sort,” and press ENTER.  
B Select the setting you want to sort by; “Recent first,”  
“Oldest first,” “By title (AtZ),” “By title (ZtA),” and  
press ENTER.  
Viewing All Titles . . . . . . . . . . . . . . . . . . . . . . 32  
Searching for a Title . . . . . . . . . . . . . . . . . . . . 34  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
About the “Movies” (All Movies) Title List  
display  
Playing a title  
a After step 3 of “Viewing All Titles” above,  
select the title you want to play, and press  
ENTER or H.  
All Movies  
1214 items  
Spider  
Smoother  
Sideway  
The title starts playing. You can apply other playback  
settings to the selected title using the “Options”  
menu (see below).  
Home  
Date  
: 2006  
Alpinist  
Electricity  
Lemon Grove  
Bridget  
Genre : Adventure  
Format : MPEG  
Finding Never-Ever Land  
Meet My Mom  
All Movies  
1214 items  
Spider  
Options  
Smoother  
Sideway  
Play from Beginning  
Add to Quicklist  
Home  
Date  
: 2006  
Alpinist  
Electricity  
Lemon Grove  
Bridget  
Genre : Adventure  
Format : MPEG  
1 Detailed information  
Displays details about the selected title.  
• Date: Displays the recording year.  
• Genre: Displays the genre name.  
Finding Never-Ever Land  
Meet My Mom  
• Format: Displays the coding format.  
The “Options” menu appears when you select a title and  
2 List area  
Displays the title names of all content.  
press ,  
To use the “Options” menu  
Press , instead of ENTER in the above step to display the  
“Options” menu settings applicable to the title in the given  
situation. In the above example, the following items are  
available.  
Items  
Details  
Play from Beginning  
Starts playing the title you selected from  
the beginning.  
Add to Quicklist  
Adds the selected title to the Quicklist.  
Example: To apply “Play from Beginning” to the selected title  
A Select “Play from Beginning,” and press ENTER.  
To play in other play mode  
During playback, press PLAY MODE repeatedly. The selected  
item changes with each press: “Time Search” (page 26) —  
“Repeat Title” — “Repeat Off”  
See page 25 for details.  
z Hint  
See page 24 for the remote’s operations.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Browsing by Genre,  
Quicklist, or Folder  
Searching for a Title  
DATA DVD  
DATA DVD  
Narrow down the list of titles by selecting the category type (e.g.,  
“Folders”), then the category.  
You can find the exact title, or titles with a similar name.  
Search Results  
5 items  
Folders  
2 items  
Say No  
Sea  
Winter games 2006  
Interviews  
Sideway  
Spider  
Stay Alive  
s_  
A
B
L
V
2
C
M
W
3
D
N
X
4
)
E
O
Y
5
F
P
Z
6
G
Q
,
H
R
.
I
S
:
J
T
;
K
U
1
7
8
9
0
_
(
SHFT  
SPC  
DEL  
CLR  
DONE  
CANCEL  
Search results are narrowed down as more characters  
are entered  
a Press SYSTEM MENU.  
a Press SYSTEM MENU.  
b Select “Title List,” and press ENTER.  
c Select “Movies,” and press ENTER.  
d Press < to turn on the Browse menu.  
e Select “Browse,” and press ENTER.  
b Select “Title List,” and press ENTER.  
c Select “Movies,” and press ENTER.  
d Press < to turn on the Browse menu.  
e Select “Search,” and press ENTER to turn on  
f Select the list you want to view from  
“Genres,” “Quicklist,” or “Folders,” and  
press ENTER.  
the above display.  
f Enter the title name using the on-screen  
The list of genres/Quicklist/folders appears as above.  
For details about the Quicklist, see “Programming  
keyboard (see page 23).  
z Hint  
You can select a title and start playback by pressing H or ENTER, or  
using the “Options” menu (press ,).  
g Select the genre/Quicklist/folder you want to  
view, and press ENTER.  
z Hint  
You can select a title and start playback by pressing H or ENTER, or  
using the “Options” menu (press ,).  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
To remove the title from the “Quicklist”  
Programming Playback  
(Quicklist)  
1
Select the title you want to remove from the  
displayed “Quicklist,” and press ,.  
2
Select “Remove,” and press ENTER.  
z Hint  
You can play the “Quicklist” content in other play modes by pressing  
PLAY MODE (page 25).  
DATA DVD  
Play your favorite titles in the order you like by making your  
own “Quicklist.”  
Note  
The “Quicklist” may be cleared after some operations (e.g., opening the  
disc tray, or turning off the player etc.).  
Quicklist  
14 items  
Spider  
Smoother  
Sideway  
Home  
Date  
: 2006  
Alpinist  
Electricity  
Lemon Grove  
Bridget  
Genre : Adventure  
Format : MPEG  
Finding Never-Ever Land  
Meet My Mom  
The “Quicklist” does not affect the original recording on  
the disc  
a Press SYSTEM MENU.  
b Select “Title List,” and press ENTER.  
c Select “Movies,” and press ENTER.  
d When the “All Movies” Title List appears,  
select the title you want to add to the top of  
the “Quicklist,” and press ,.  
e Select “Add to Quicklist” from the “Options”  
menu, and press ENTER.  
f Repeat step 4 and 5 to select all the desired  
titles.  
Select in the order you want to play. You can add the  
same title multiple times.  
The “Quicklist” can contain up to 25 titles.  
g Press < to turn on the Browse menu.  
h Select “Browse,” and press ENTER.  
i Select “Quicklist,” and press ENTER to turn  
on the above display.  
The “Quicklist” Title List appears with the  
programmed content.  
j Select the title you want to start playback,  
and press ENTER.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Viewing All Artists  
Listening to  
Music Files  
DATA DVD  
The “Music” Title List first displays a list of the artist names on  
the disc.  
Use the “Music” Title List to browse  
through and play the MP3 track files on  
DATA DVDs. You can make a “Quicklist”  
of your favorites and play in various play  
modes.  
A
r
t
i
s
t
s
7
items  
A
l
l
Artis  
A
n
g
e
l
a
S
i
on  
6
Albums  
B
l
u
e
Glas  
5  
Albums  
B
o
h
e
m
i
a
n  
t
6  
Albums  
Cela
4  
Albums  
C
l
a
s
s
i
c
x
5  
Albums  
Commotion  
2  
Albums  
C
o
u
n
t
Drala  
2  
Albums  
The Browse menu appears when you press <  
a Press SYSTEM MENU.  
b Select “Title List,” and press ENTER.  
c Select “Music,” and press ENTER.  
The above “Artists” display appears, showing all  
artist names (scrollable by pressing m). From  
“Artists” you can apply items to all tracks using the  
Browse menu (see below).  
To use the Browse menu  
Press < after step 3 to display the items for the “Music” Title  
List. For operations, see the pages in parentheses. Available  
items differ depending on the display.  
Items  
Details  
All Songs  
Browse  
Lists all tracks (page 37).  
Displays a list of artists, albums, genres,  
Quicklist, or folders (page 38).  
Search  
Searches for a track using the on-screen  
keyboard (page 38).  
Sort  
Reorders the tracks by alphabet, or year,  
etc. (see below).  
Now Playing  
Displays the track information and the  
playback information during playback.  
Example: To apply “Sort” to all tracks  
A To display the list of tracks, select “All Songs” from the  
Browse menu and press ENTER.  
B Press < to turn on the Browse menu.  
C Select “Sort,” and press ENTER.  
Viewing All Artists . . . . . . . . . . . . . . . . . . . . . 36  
D Select the setting you want to sort by; “Recent first,”  
“Oldest first,” “By title (AtZ),” “By title (ZtA),” “By  
artist (AtZ),” “By artist (ZtA),” and press ENTER.  
Browsing by Artist, Album, Genre, Quicklist,  
or Folder . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
Searching for a Track . . . . . . . . . . . . . . . . . . . 38  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
About the “Music” (All Songs) Title List display  
Playing a track  
All Songs  
1214 items  
a After step 3 of “Viewing All Artists” above,  
narrow down the list of tracks by selecting  
the artist, then the album.  
Never Let Me Down (Split Mix)  
9:31  
8:00  
7:31  
3:55  
6:33  
5:26  
4:57  
9:36  
6:18  
6:18  
Policies of Truth  
Shout in Rio  
Home  
Artist:DeepGreen  
Album:Splash!
Genre:Alternative  
Format:MP3  
Strangled  
To list all tracks, press < and select “All Songs”  
from the Browse menu.  
Rash (Spiritual Mix)  
I Feel You (Remix)  
Route 57 (Beatmasters Mix)  
Free (DJ Remix)  
Personal Note  
b Select the track you want to play, and press  
ENTER or H.  
The title starts playing. You can apply other playback  
settings to the selected track using the “Options”  
menu (see below).  
1 Detailed information  
Displays details about the selected track.  
• Artist: Displays the artist name.  
All Songs  
1214 items  
• Album: Displays the album name.  
• Genre: Displays the genre name.  
• Format: Displays the coding format.  
Never Let Me Down (Split Options  
Policies of Truth  
Shout in Rio  
Play Song  
Add to Quicklist  
Home  
Artist : Deep Green  
Album : Splash!  
Genre : Alternative  
Format : MP3  
Strangled  
Rash (Spiritual Mix)  
I Feel You (Remix)  
Route 57 (Beatmasters Mix
Free (DJ Remix)  
Personal Note  
2 List area  
Displays overall content.  
• Main area: Displays the track names.  
• Sub area: Displays the total playback time of each  
track.  
The “Options” menu appears when you select a track  
and press ,  
About unplayable audio track files  
The player does not play the file if:  
The DATA DVD is not recorded in an MP3 format that  
conforms to UDF (Universal Disk Format).  
The audio track file does not have the extension “.MP3.”  
The data is not formatted properly even though it has the  
extension “.MP3.”  
The data is not MPEG-1 Audio Layer III data.  
The data is recorded in mp3PRO format.  
The file name contains characters other than numbers and  
English alphabet.  
To use the “Options” menu  
Press , instead of ENTER in the above step to display the  
“Options” menu settings applicable to the track in the given  
situation. In the above example, the following items are  
available.  
Items  
Details  
Play Song  
Starts playing the track you selected from  
the beginning.  
Add to Quicklist  
Adds the selected track to the Quicklist.  
Example: To apply “Play Song” to the selected track  
A Select “Play Song,” and press ENTER.  
To play in other play mode  
During playback, press PLAY MODE repeatedly. The selected  
item changes with each press: “Repeat Track” — “Repeat All”  
— “Random” — “Repeat Off”  
See page 25 for details.  
z Hints  
• See page 24 for the remote’s operations.  
• Even after stopping playback, the player resumes playback from the  
last track you played.  
• Depending on the writing software used, the displayed track or album  
names may be different from the characters you input.  
Notes  
• Playback time of MP3 audio tracks may not be displayed correctly.  
• If you put an extension “.MP3” to a non-MP3 file, the file may  
accidentally play on the player. Note that such output may cause the  
connected device to malfunction.  
• Playback may not start immediately after skipping to another album.  
• When using the Resume function on MP3 tracks, playback starts from  
the beginning of the track.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Browsing by Artist, Album, Searching for a Track  
Genre, Quicklist, or Folder  
DATA DVD  
DATA DVD  
Narrow down the list of tracks by selecting the category type  
(e.g., “Genres”), then the category.  
You can find the exact track, or tracks with a similar name.  
Search Results  
7 items  
9:31  
Genres  
20 items  
Raga  
All Genres  
Raging Plants  
Ragamufin  
Ree  
Alternative  
Blues  
8:00  
7:31  
7:32  
6:33  
6:34  
6:35  
2876 Songs  
195 Songs  
16 Songs  
304 Songs  
841 Songs  
32 Songs  
2 Songs  
Books And Spoken  
Celtic  
Rise  
R
Rose Bed  
Rule the World  
Classical  
Comedy  
A
B
L
V
2
C
M
W
3
D
N
X
4
)
E
O
Y
5
F
P
Z
6
G
Q
,
H
R
.
I
S
:
J
T
;
K
U
1
Country  
Dance  
460 Songs  
60 Songs  
7
8
9
0
Dark  
_
(
SHFT  
SPC  
DEL  
CLR  
DONE  
CANCEL  
Search results are narrowed down as more characters  
are entered  
Genres without content do not appear in the list  
a Press SYSTEM MENU.  
a Press SYSTEM MENU.  
b Select “Title List,” and press ENTER.  
c Select “Music,” and press ENTER.  
d Press < to turn on the Browse menu.  
e Select “Browse,” and press ENTER.  
b Select “Title List,” and press ENTER.  
c Select “Music,” and press ENTER.  
d Press < to turn on the Browse menu.  
e Select “All Songs,” and press ENTER.  
f Press < to turn on the Browse menu.  
f Select the list you want to view from  
“Artists,” “Albums,” “Genres,” “Quicklist”  
or “Folders,” and press ENTER.  
The list of artists/albums/genres/Quicklist/folders  
appears as above.  
g Select “Search,” and press ENTER to turn on  
the above display.  
For details about the Quicklist, see “Programming  
h Enter the track name using the on-screen  
keyboard (see page 23).  
g Select the artist/album/genre/Quicklist/  
z Hints  
folder you want to view, and press ENTER.  
• You can select a track from the search result, and start playback by  
pressing ENTER or H, or using the “Options” menu (press ,).  
• You can search for a genre, artist, album, or folder name from each  
Title List (e.g., “Genres”).  
z Hint  
You can select a track from the list of tracks, and start playback by  
pressing ENTER or H, or using the “Options” menu (press ,).  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
To remove the title from the “Quicklist”  
Programming Playback  
(Quicklist)  
1
Select the track you want to remove from the  
displayed “Quicklist,” and press ,.  
2
Select “Remove,” and press ENTER.  
z Hint  
You can play the “Quicklist” content in other play modes by pressing  
PLAY MODE (page 25).  
DATA DVD  
Play your favorite tracks in the order you like by making your  
own “Quicklist.”  
Note  
The “Quicklist” may be cleared after some operations (e.g., opening the  
disc tray, or turning off the player etc.).  
Quicklist  
3 items  
9:31  
Never Let Me Down (Split Mix)  
Policies of Truth  
Shout in Rio  
8:00  
7:31  
Artist : Deep Green  
Album : Splash!  
Genre : Alternative  
Format : MP3  
The “Quicklist” does not affect the original recording on  
the disc  
a Press SYSTEM MENU.  
b Select “Title List,” and press ENTER.  
c Select “Music,” and press ENTER.  
d Press < to turn on the Browse menu.  
e Select “All Songs,” and press ENTER.  
f When the “All Songs” Title List appears,  
select the track you want to add to the top of  
the “Quicklist,” and press ,.  
g Select “Add to Quicklist” from the “Options”  
menu, and press ENTER.  
h Repeat step 6 and 7 to select all the desired  
tracks.  
Select in the order you want to play. You can add the  
same track multiple times.  
The “Quicklist” can contain up to 25 tracks.  
i Press < to turn on the Browse menu.  
j Select “Browse,” and press ENTER.  
k Select “Quicklist,” and press ENTER to turn  
on the above display.  
The “Quicklist” Title List appears with the  
programmed content.  
l Select the track you want to start playback,  
and press ENTER.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Viewing All Folders  
Viewing Photo  
Files  
DATA DVD  
The “Photos” Title List first displays all the folders on the disc.  
Use the “Photos” Title List to view the  
JPEG images on DATA DVDs. You can  
reorder the files and start playing a  
slideshow.  
Folders  
2 items  
Kurobe-dam 2005  
Jungfraujoch 2006  
The Browse menu appears when you press < while on  
the leftmost row  
a Press SYSTEM MENU.  
b Select “Title List,” and press ENTER.  
c Select “Photos,” and press ENTER.  
The above “Folders” display appears, showing all  
folders (scrollable by pressing m). From “Folders”  
you can apply items to all files using the Browse  
menu (see below).  
To use the Browse menu  
Press < after step 3 to display the items for “Photos” Title List.  
For operations, see the pages in parentheses. Available items  
differ depending on the display.  
Items  
Details  
All Photos  
Displays all files in alphabetical order  
Browse  
Search  
Sort  
Displays a list of dates, Quicklist, or  
folders (page 42).  
Searches for a file using the on-screen  
keyboard (page 42).  
Reorders the files by date or alphabet (see  
below).  
Example: To apply “Sort” to all files  
A To display the list of all files, select “All Photos” from the  
Browse menu and press ENTER.  
B Move the highlight to the left most row, and press < to  
turn on the Browse menu.  
C Select “Sort,” and press ENTER.  
D Select the setting you want to sort by; “Recent first,”  
“Oldest first,” “By title (AtZ),” “By title (ZtA),” and  
press ENTER.  
Viewing All Folders. . . . . . . . . . . . . . . . . . . . . 40  
Searching for a Photo. . . . . . . . . . . . . . . . . . . 42  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
About the “Photos” (All Photos) Title List  
display  
Playing a slideshow  
a After step 3 of “Viewing All Folders” above,  
press < and select “All Photos” from the  
Browse menu.  
All Photos  
1214 items  
File:DSC00434.jpg
Date:7/23/2006  
Resolution:293x196
Format:JPEG  
b Select the file you want to start from, and  
press ENTER to turn on the “Options”  
menu.  
c Select “Slideshow,” and press ENTER.  
Slideshow starts.  
You can apply other playback settings to the selected  
file using the “Options” menu (see below).  
1 Detailed information  
Displays details about the selected file.  
• File: Displays the file name.  
All Photos  
1214 items  
• Date: Displays the shooting date.  
• Resolution: Displays the picture resolution in width ×  
height.  
Options  
Slideshow  
Add to Quicklist  
File : DSC00434.jpg  
Date  
:
7/23/2006  
Resolution: 293 x 196  
Format: JPEG  
• Format: Displays the recording format.  
2 List area  
Displays overall photo content in thumbnail.  
About unplayable photo files  
The “Options” menu appears when you select a file and  
press ENTER  
The player does not play the file if:  
The DATA DVD is not recorded in a JPEG format that  
conforms to UDF (Universal Disk Format).  
The photo file is not recorded in a format that conforms to the  
DCF*.  
The file has an extension other than “.JPEG.”  
The image is larger than 4,096 (width) × 4,096 (height) in  
normal mode, or progressive JPEG.  
To use the “Options” menu  
Available “Options” menu settings differ depending on the  
situation. In the above example of the use of the “Options”  
menu, the following items are available.  
The image does not fit the screen (the image is reduced).  
The file name contains characters other than numbers and  
English alphabet.  
• Even when the above are not applicable, some files may not  
play depending on the recording condition or the method (e.g.,  
writer software).  
Items  
Details  
Slideshow  
Add to Quicklist  
Starts playing a slideshow as above.  
Adds the selected file to the Quicklist for  
later slideshow playback.  
• Files may not play on this player if edited on a PC.  
* “Design rule for Camera File system”: Image standards for digital  
cameras regulated by JEITA (Japan Electronics and Information  
Technology Industries Association).  
To play in other play mode  
During playback, press PLAY MODE repeatedly. The selected  
item changes with each press:  
“Repeat All” — “Random” — “Repeat Off”  
See page 25 for details.  
z Hints  
• See page 24 for the remote’s operations.  
• Even after stopping playback, the player resumes playback from the  
last file you played.  
Note  
The photos may appear slowly depending on the size and the number of  
files.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Browsing by Date,  
Quicklist, or Folder  
Searching for a Photo  
DATA DVD  
DATA DVD  
Narrow down the list of files by selecting the category type (e.g.,  
“Date”), then the category.  
You can find the exact file, or files with a similar name.  
10 items  
Search Results  
7 items  
Year  
2007  
2006  
2005  
2004  
2003  
2002  
2001  
2000  
1999  
1998  
R_  
A
B
L
V
2
C
M
W
3
D
N
X
4
)
E
O
Y
5
F
P
Z
6
G
Q
,
H
R
.
I
S
:
J
T
;
K
U
1
7
8
9
0
_
(
SHFT  
SPC  
DEL  
CLR  
DONE  
CANCEL  
Search results are narrowed down as more characters  
are entered  
a Press SYSTEM MENU.  
a Press SYSTEM MENU.  
b Select “Title List,” and press ENTER.  
c Select “Photos,” and press ENTER.  
d Press < to turn on the Browse menu.  
e Select “Browse,” and press ENTER.  
b Select “Title List,” and press ENTER.  
c Select “Photos,” and press ENTER.  
d Press < to turn on the Browse menu.  
e Select “All Photos,” and press ENTER.  
f Select the list you want to view from “Date,”  
“Quicklist,” or “Folders” and press ENTER.  
The list of date/Quicklist/folders appears as above.  
For details about the Quicklist, see “Programming a  
f Move the highlight to the leftmost row, and  
press < to turn on the Browse menu.  
g Select “Search,” and press ENTER to turn on  
the above display.  
g Select the date/Quicklist/folder you want to  
view, and press ENTER.  
h Enter the file name using the on-screen  
keyboard (see page 23).  
z Hint  
You can select a file and start slideshow by using “Options” menu (press  
,).  
z Hint  
You can select a file and start slideshow by using “Options” menu (press  
,).  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
m Select “Slideshow” from the “Options”  
menu, and press ENTER.  
Programming a Slideshow  
Playback (Quicklist)  
To remove from the “Quicklist”  
1
Select the file you want to remove from the  
displayed “Quicklist,” and press ENTER.  
DATA DVD  
2
Select “Remove,” and press ENTER.  
Play a slideshow in the order you like by making your own  
“Quicklist.”  
z Hint  
You can play the “Quicklist” content in other play modes by pressing  
PLAY MODE (page 25).  
Quicklist  
22 items  
Note  
The “Quicklist” may be cleared after some operations (e.g., opening the  
disc tray, or turning off the player etc.).  
File : DSC00434.jpg  
Date  
:
7/23/2006  
Resolution: 293 x 196  
Format: JPEG  
The “Quicklist” does not affect the original recording on  
the disc  
a Press SYSTEM MENU.  
b Select “Title List,” and press ENTER.  
c Select “Photos,” and press ENTER.  
d Press < to turn on the Browse menu.  
e Select “All Photos,” and press ENTER.  
f When the “All Photos” Title List appears,  
select the file you want to add to the top of the  
“Quicklist,” and press ENTER.  
g Select “Add to Quicklist” from the “Options”  
menu, and press ENTER.  
h Repeat step 6 and 7 to select all the desired  
files.  
Select in the order you want to play. You can add the  
same file multiple times.  
The “Quicklist” can contain up to 25 files.  
i Move the highlight to the leftmost row, and  
press < to turn on the Browse menu.  
j Select “Browse,” and press ENTER.  
k Select “Quicklist,” and press ENTER to turn  
on the above display.  
The “Quicklist” Title List appears with the  
programmed content.  
l Select the file you want to start playback, and  
press ENTER.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Using the Setup Displays  
Changing the  
BD  
DVD  
DATA DVD  
CD  
From the “System Menu,” enter the “Setup” displays to change  
the settings of the player.  
Initial Settings  
Select “Setup” from the “System Menu”  
when you need to change the settings of the  
player (e.g., when changing the connected  
device or the audio/video output, etc.).  
The last part of this section explains how to  
return all of these settings to their factory  
defaults.  
Setup  
Video Setup  
Audio Setup  
Language  
TV Type  
16:9  
4:3 Video Out  
DVD Aspect Ratio  
YCbCr/RGBPC(HDMI)  
24p Output  
Normal  
Letter Box  
Y, Cb, Cr  
Off  
Parental Control  
Speakers  
Options  
Note  
Playback settings described in this section may not work  
when there is any preset playback setting in the disc. The  
disc’s playback settings take priority over the player’s  
playback settings.  
a Press SYSTEM MENU while the player is  
stopped.  
b Select “Setup,” and press ENTER.  
c Select the “Setup” display you want to use,  
from “Video Setup,” “Audio Setup,”  
“Language,” “Parental Control,”  
“Speakers,” or “Options,” and press  
ENTER.  
The “Setup” display appears with the related items.  
Note that the display switches to the screen saver if  
you do not operate for 15 minutes.  
d Select the item you want to change, and press  
ENTER.  
Refer to the explanations in the following sections.  
To return to the previous display  
Press RETURN.  
Using the Setup Displays . . . . . . . . . . . . . . . . 44  
Video Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 45  
Audio Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49  
Parental Control . . . . . . . . . . . . . . . . . . . . . . . 50  
Speakers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51  
Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52  
Resetting the Player . . . . . . . . . . . . . . . . . . . . 53  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Video Setup  
Underlined items are the default settings.  
TV Type  
4:3  
4:3 screen TV.  
Select your TV type.  
16:9  
Wide-screen TV, or a TV with a wide mode function.  
4:3 Video Out  
Full  
Displays a 4:3 screen picture in 16:9 aspect ratio.  
Select the display configuration for a 4:3  
screen picture on a 16:9 wide screen TV.  
Normal  
Displays a 4:3 screen picture in 4:3 aspect ratio with black bands on the sides. Select  
this if your TV does not have a 4:3 screen mode.  
DVD Aspect Ratio  
Letter Box  
Displays a wide picture with black bands on the top and  
bottom.  
Select the display configuration for a 16:9  
DVD picture on a 4:3 screen TV (selectable  
when “TV Type” is set to “4:3”).  
Note that the aspect ratio is fixed on some  
discs. For example, a 4:3 letterbox picture  
may appear even when “Pan & Scan” is  
selected.  
Pan & Scan  
Displays a full-height picture on the entire screen, with  
trimmed sides.  
YCbCr / RGBPC (HDMI)  
Y, Cb, Cr  
Select this when connecting to an HDMI device.  
Select the type of output from the HDMI  
OUT jack.  
RGB (16-235)  
Select this when connecting to a device with an HDCP-compliant DVI jack.  
RGB (0-255)  
Select this when connecting to an RGB (0-255) device.  
24p Output  
On  
Sends 1920 × 1080p/24 Hz video signals when playing Film-based materials on BD-  
ROMs (720p/24 Hz or 1080p/24 Hz). Select this when the connection applies.  
For connection to a 1080/24p-compatible TV  
using the HDMI OUT jack.  
Off  
Select this for any other connection.  
Note  
“TV Type” and “DVD Aspect Ratio” can be set when video output resolution is 480i/480p.  
,continued  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
To set the video output resolution  
Press VIDEO FORMAT repeatedly to select the desired resolution. Note that the resolution differs depending on the display device,  
connecting jack and the source material as below.  
Connecting  
HDMI OUT  
COMPONENT VIDEO OUT  
VIDEO/S VIDEO  
jack  
Settings  
Auto  
Automatically selects the  
recommended resolution acceptable  
for your TV.  
480i  
480i  
480i  
480i  
480i  
480i  
480i  
480i  
480i  
480i  
480i  
480p  
480p  
480p  
3
720p  
720p  
BD:720p, DVD:480p*  
3
1080i  
1080i  
BD:1080i, DVD:480p*  
1080p  
Source Direct  
1080p  
480i  
Output differs depending on source  
material*  
Output differs depending on source  
material*  
1
2
1
* Outputs in the same resolution and frequency as recorded on the disc.  
2
* 1080/24p video signals are not output from the COMPONENT VIDEO OUT jacks.  
3
* Outputs in the resolution of the original setting (720p or 1080i) when the DVD is not copy guarded.  
Notes  
• If the picture is not clear, natural or to your satisfaction, try another resolution that suits the disc and your TV/projector, etc. For the details, refer also  
to the instruction manual supplied with the TV/projector, etc.  
• 480i or 480p video signals may be output when you connect to the COMPONENT VIDEO OUT jacks and play some copy-guarded BDs/DVDs. To  
enjoy the HD quality resolution in this case, connect the display device to the HDMI OUT jack using an HDMI cord.  
• Even when you select a setting other than “Auto,” the player automatically adjusts the video signals if the TV cannot accept the set resolution.  
To output the 1080/24p video signals  
A 1080/24p-compatible TV is required for this setting.  
1
2
Set “24p Output” in “Video Setup” to “On” (page 45).  
Press VIDEO FORMAT repeatedly to select “Auto” or “Source Direct.”  
Note  
If there is no picture, press VIDEO FORMAT repeatedly until the picture appears correctly.  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Audio Setup  
Underlined items are the default settings. Since many factors  
affect the type of audio output, see also “About the audio output  
Dolby Digital  
Dolby Digital  
Select this when connecting to a device with a built-in Dolby Digital decoder.  
Select the audio signals output when playing  
Dolby Digital discs. This setting affects the  
output from the DIGITAL OUT (COAXIAL  
or OPTICAL) jack.  
Downmix PCM  
Converts to output Linear PCM signals. Select this when connecting to a device  
without a built-in Dolby Digital decoder.  
DTS  
DTS  
Select this when connecting to a device with a built-in DTS decoder.  
Select the audio signals output when playing  
DTS discs. This setting affects the output  
from the DIGITAL OUT (COAXIAL or  
OPTICAL) jack.  
Downmix PCM  
Converts to output Linear PCM signals. Select this when connecting to a device  
without a built-in DTS decoder.  
DTS Downmix  
Stereo  
Downmixes multi-channel audio signals for two channel stereo.  
Select the type of 2-channel signals when  
down-mixed from multi-channel DTS  
sources (effective for audio connections  
when “DTS” is set to “Downmix PCM”).  
Lt/Rt  
Allows you to hear surround sound when the connected device has a built-in Dolby  
Pro Logic decoder.  
Audio (HDMI)  
Auto  
Normally, select this. Outputs audio signals according to the status of the connected  
HDMI device.  
Select the output method from the HDMI  
OUT jack.  
PCM  
Converts all audio signals to Linear PCM.  
,continued  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
About the audio output signals  
The audio output differs as follows, depending on the source, output jack, and the selected settings.  
Jacks/  
settings  
DIGITAL OUT (OPTICAL/  
COAXIAL) jacks*  
1
3
AUDIO OUT L/R jacks*  
HDMI OUT jack*  
2
Disc/source  
4
4
2ch  
5.1ch  
PCM  
Bitstream  
PCM*  
Auto*  
BD-  
ROM  
Linear PCM 2ch  
2ch  
2ch  
2ch LPCM  
2ch LPCM  
2ch LPCM  
2ch LPCM  
5.1ch LPCM  
7.1ch LPCM  
Dolby Digital  
Dolby Digital  
Dolby Digital  
DTS  
2ch Downmix 2ch Downmix  
LPCM LPCM  
2ch Downmix 2ch Downmix  
5
5.1ch  
*
2ch Downmix 5.1ch  
5.1ch LPCM  
7.1ch LPCM  
5.1ch  
Downmix  
7.1ch  
2ch Downmix  
LPCM  
LPCM  
2ch Downmix  
LPCM  
Dolby Digital  
2ch Downmix 5.1ch  
2ch Downmix 5.1ch  
2ch Downmix 5.1ch  
2ch Downmix 5.1ch  
2ch Downmix 5.1ch  
Dolby Digital 5.1ch LPCM  
2ch Downmix  
LPCM  
6
Dolby Digital Plus  
Dolby TrueHD  
DTS  
Dolby Digital 7.1ch LPCM  
*
2ch Downmix  
LPCM  
Dolby Digital 5.1ch LPCM  
2ch Downmix  
LPCM  
DTS  
5.1ch LPCM  
5.1ch LPCM  
2ch LPCM  
2ch Downmix  
LPCM  
DTS-HD  
DTS  
DTS  
DVD  
Linear PCM  
Dolby Digital  
DTS  
2ch  
2ch  
2ch LPCM  
2ch LPCM  
2ch LPCM  
Dolby Digital  
DTS  
2ch Downmix  
LPCM  
2ch Downmix 5.1ch  
2ch Downmix 5.1ch  
Dolby Digital 5.1ch LPCM  
2ch Downmix  
LPCM  
DTS  
5.1ch LPCM  
2ch LPCM  
2ch LPCM  
5.1ch LPCM  
MPEG  
2ch  
2ch  
2ch  
2ch  
2ch LPCM  
2ch LPCM  
2ch LPCM  
2ch LPCM  
DTS  
CD  
Linear PCM 2ch  
DTS  
2ch LPCM  
DTS  
2ch Downmix  
LPCM  
2ch Downmix 5.1ch  
1
*
*
“2 Channel” and “5.1 Channel” are selectable under “Audio Output Mode” in “Speakers” Setup (page 51).  
PCM : when “Dolby Digital” or “DTS” in “Audio Setup” is set to “Downmix PCM” (page 47).  
Bitstream : when “Dolby Digital” or “DTS” in “Audio Setup” is set to “Dolby Digital” or “DTS” (page 47).  
Selectable under “Audio (HDMI)” in “Audio Setup” (page 47).  
Selectable under “Audio (HDMI)” in “Audio Setup” (page 47). Resulting output may differ depending on the connected HDMI device.  
When the sampling frequency is 192 kHz, the player downmixes to 2ch signals even if the disc or source is 5.1ch.  
Outputs 7.1ch LPCM signals decoded from Dolby Digital Plus audio stream.  
2
3
4
5
6
*
*
*
*
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Language  
Underlined items are the default settings.  
Notes  
• When you select a language in “Audio,” “Subtitles,” “BD/DVD Menu”  
that is not recorded on the disc, one of the recorded languages is  
automatically selected.  
• Playback settings stored in the disc take priority over these settings.  
OSD  
English  
Displays the menus and messages in English.  
Select your language for the player on-screen  
displays.  
Français  
Displays the menus and messages in French.  
Audio  
English  
Plays the soundtrack in English.  
Select the default soundtrack language for  
BD-ROMs/DVD VIDEOs.  
French  
Plays the soundtrack in French.  
Other  
See “Language Code List” on page 68 and enter the code for your language.  
Subtitles  
English  
Displays the subtitles in English.  
Select the default subtitle language for BD-  
ROMs/DVD VIDEOs.  
French  
Displays the subtitles in French.  
Other  
See “Language Code List” on page 68 and enter the code for your language.  
BD/DVD Menu  
w/Subtitle  
Displays BD’s/DVD’s menus in the same language as the subtitle language.  
Select the default menu language for BD-  
ROMs/DVD VIDEOs.  
English  
Displays BD’s/DVD’s menus in English.  
French  
Displays BD’s/DVD’s menus in French.  
Other  
See “Language Code List” on page 68 and enter the code for your language.  
Subtitle Display  
On  
Turns on the subtitles.  
Off  
Turns off the subtitles.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Parental Control  
This function limits playback of DVD VIDEOs and BD-ROMs.  
To activate, see “Locking a Disc(page 29).  
The default settings are underlined.  
Notes  
• You cannot limit playback if the disc does not have the Parental Control  
function.  
• If you forget the password for “Parental Control,” you will need to reset  
the player (page 53). Note that all the settings you made also return to  
their defaults.  
Change Password (Set Password)  
Next Screen  
Set or change the password for the “Parental Control” function. You will be asked for  
the password when playing restricted discs or when changing the control level.  
DVD Parental Control  
Change Level  
Set the control level. The display asks for the password if the disc’s pre-determined  
level exceeds the limit you set. The default setting is “Off.”  
DVD Country Code  
This ensures that you see the scenes intended for your residential area.  
BD Parental Control  
Change Age Restriction  
Set the control level. The display asks for the password if the disc’s pre-determined  
age restriction is higher than the age you set. The default setting is “255.”  
BD Country Code  
This ensures that you see the scenes intended for your residential area when playing  
BD-ROMs.  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Speakers  
The following items are necessary when using the 5.1CH  
OUTPUT jacks.  
The default settings are underlined.  
Audio Output Mode  
2 Channel  
Select this when connecting to an AV amplifier (receiver) using the AUDIO OUT (L/  
R) jacks.  
For analog connection.  
5.1 Channel  
Select this when connecting to an AV amplifier (receiver) using the 5.1CH OUTPUT  
jacks.  
Speaker Setup  
Next Screen  
1 Select the speaker setting that needs adjusting by pressing M/m.  
• “C” (center speaker): “Yes” or “No”  
• “Ls/Rs” (left surround speaker/right surround speaker): “Yes” or “No”  
• “L/R” (left front speaker/right front speaker): “Large” or “Small”  
2 Adjust the setting by pressing </,.  
This setting affects the output from the  
5.1CH OUTPUT jacks.  
• For “C” and “Ls/Rs,” select whether the speakers are included in your system.  
• For “L/R,” select the size. This setting is disabled if either of “C” or “Ls/Rs” is set  
to “No.”  
3 Press ENTER to save the adjustments.  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Options  
Underlined items are the default settings.  
On Screen Display  
On  
Displays playback status.  
Select whether to display the playback status  
on the screen (Stop, Play, etc.).  
Off  
Playback status is not displayed.  
Auto Power Off  
On  
Turns off the player when the player is left in stop or pause mode without operation  
for 30 minutes.  
Off  
Select whether to activate the “Auto Power  
Off” function of the player.  
The player remains turned on with or without operation.  
Easy Setup  
Start  
Press ENTER and see page 18.  
Re-runs the Easy Setup to make the basic  
settings.  
HDMI Control  
On  
Activates the function.  
Off  
Turns off the function.  
Select whether to activate the HDMI Control  
function of the player (page 11).  
Hybrid Disc Playback Layer  
BD  
Plays BD layer.  
DVD  
Plays DVD layer.  
CD  
Select the layer priority when playing a  
Hybrid Disc. Remove the disc when you  
change the setting.  
Plays CD layer.  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Resetting the Player  
You can return all of the player settings to their factory defaults.  
@/1  
x
HDMI  
HD  
FL OFF  
a When the power is on, hold down x on the  
front panel, and press @/1.  
The player turns off, and all of the settings return to  
their factory defaults.  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Troubleshooting  
If you experience any of the following difficulties while using  
the player, use this troubleshooting guide to help remedy the  
problem before requesting repairs. Should any problem persist,  
consult your nearest Sony dealer (For customers in the USA  
only).  
Additional  
Information  
Power  
The power does not turn on.  
, Check that the power cord is connected securely.  
, It takes a short while before the player turns on.  
Picture  
There is no picture/picture noise appears.  
, Re-connect the connecting cord securely.  
, The connecting cords are damaged.  
, Check the connection to your TV (page 10) and switch the  
input selector on your TV so that the signal from the player  
appears on the TV screen.  
, The disc is dirty or flawed.  
, If the picture output from your player goes through your  
VCR to get to your TV or if you are connected to a  
combination TV/VIDEO player, the copy-protection signal  
applied to some BD/DVD programs could affect picture  
quality. If you still experience problems even when you  
connect your player directly to your TV, try connecting your  
player to your TV’s S VIDEO input (page 10).  
, The player is connected to an input device that is not HDCP-  
compliant (the HDMI indicator on the front panel does not  
light up). See page 11.  
, If the HDMI OUT jack or the COMPONENT VIDEO OUT  
jacks are used for video output, changing the output  
resolution may solve the problem (page 46). Press VIDEO  
FORMAT repeatedly until the picture appears correctly.  
, Depending on the disc, the picture quality may be poor when  
the VIDEO FORMAT setting is set to other than “480i,”  
even when the player is connected to a progressive or HD  
TV using a component cord or an HDMI cord. If this  
happens, press VIDEO FORMAT repeatedly to switch to  
“480i.”  
, When playing a double-layer DVD, the video and audio may  
be momentarily interrupted at the point where the layers  
switch.  
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 54  
Self-Diagnosis Function . . . . . . . . . . . . . . . . . 57  
Index to Parts and Controls . . . . . . . . . . . . . . 58  
GNU License Information . . . . . . . . . . . . . . . . 60  
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66  
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . 67  
Language Code List . . . . . . . . . . . . . . . . . . . . 68  
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70  
There is no picture or picture noise appears  
when connected to the HDMI OUT jack.  
, Try the following: 1Turn the player off and on again.  
2Turn the connected equipment off and on again.  
3Disconnect and then connect the HDMI cord again.  
, If the HDMI OUT jack is used for video output, changing the  
video output resolution may solve the problem (page 46).  
Press VIDEO FORMAT repeatedly until the picture appears  
correctly.  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
, The disc is skewed.  
The picture does not fill the screen, even  
though the aspect ratio is set in “TV Type”  
, The player cannot play certain discs (page 6).  
, The region code on the BD/DVD does not match the player.  
, Moisture has condensed inside the player (page 3).  
, The player cannot play a recorded disc that is not correctly  
finalized (page 6).  
under “Video Setup.”  
, The aspect ratio of the disc is fixed on your BD/DVD. See  
, The movie file size exceeds 2 GB.  
, The file on the DATA DVD contains characters other than  
numbers and English alphabet.  
The dark area of the picture is too dark/the  
bright area is too bright or unnatural.  
, Set “Video Control” in “A/V Control” to “Standard”  
(default) (page 28).  
, Adjust each picture setting for “Memory” in “Video  
Control” to midpoint (default) (page 28).  
The MP3 audio track file cannot be played  
, The DATA DVD is not recorded in the MP3 format that  
conforms to UDF (Universal Disk Format).  
, The audio track file does not have the extension “.MP3.”  
, The data is not formatted properly even though it has the  
extension “.MP3.”  
, The data is not MPEG-1 Audio Layer III data.  
, The player cannot play audio tracks in mp3PRO format.  
, Characters other than numbers and English alphabet are  
contained in the file name.  
Sound  
There is no sound.  
, The disc is dirty or flawed.  
, Re-connect the connecting cord securely.  
, The connecting cord is damaged.  
, The player is connected to the wrong input jack on the  
amplifier (receiver) (page 12).  
, The amplifier (receiver) input is not correctly set.  
, The player is in pause mode or in Slow-motion Play mode.  
, The player is in scan mode.  
, If the audio signal does not come through the DIGITAL  
OUT (OPTICAL or COAXIAL)/HDMI OUT jack, check  
the audio settings (page 47).  
The photo file cannot be played (page 40).  
, The disc is dirty or flawed.  
, The DATA DVD is not recorded in a JPEG format that  
conforms to UDF (Universal Disk Format).  
, The file has an extension other than “.JPEG” or “.JPG.”  
, The image is larger than 4,096 (width) × 4,096 (height) in  
normal mode. (Some progressive JPEG files cannot be  
displayed even if the file size is within this specified  
capacity.)  
, The image does not fit the screen (the image is reduced).  
, The photo file format does not conform to DCF* (page 41).  
, Characters other than numbers and English alphabet are  
contained in the file name.  
, The equipment connected to the HDMI OUT jack does not  
conform to the audio signal format, in this case set “Audio  
(HDMI)” in “Audio Setup” to “PCM” (page 47).  
* “Design rule for Camera File system”: Image standards for digital  
cameras regulated by JEITA (Japan Electronics and Information  
Technology Industries Association).  
The sound is not output correctly.  
, Check the “Audio Output Mode” in “Speakers” Setup  
(page 51) if the AUDIO OUT (L/R) jacks or the 5.1CH  
OUTPUT jacks are used for audio connection.  
The file name is not correctly displayed.  
, The player can only display numbers and alphabet. Other  
characters may be displayed differently.  
, Depending on the writing software used, the input characters  
may be displayed differently.  
No sound is output from the HDMI OUT jack  
, Try the following: 1Turn the player off and on again.  
2Turn the connected equipment off and on again.  
3Disconnect and then reconnect the HDMI cord.  
, The HDMI OUT jack is connected to a DVI device (DVI  
jacks do not accept audio signals).  
The disc does not start playing from the  
beginning.  
, Random Play or Repeat Play is selected (page 25).  
, Resume play mode is on (page 20).  
The sound volume is low.  
, The sound volume is low on some BDs/DVDs. The sound  
volume may improve if you adjust the “Audio Control”  
setting in “A/V Control” (page 27).  
The player starts playing the disc  
automatically.  
, The disc features an auto playback function.  
Operation  
Playback stops automatically.  
The remote does not function.  
, While playing discs with an auto pause signal, the player  
stops playback at the auto pause signal.  
, The batteries in the remote are weak (page 16).  
, There are obstacles between the remote and the player.  
, The distance between the remote and the player is too far.  
, The remote is not pointed at the remote sensor on the player.  
The disc does not play.  
, The disc is turned over. Insert the disc with the playback side  
facing down.  
,continued  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Some functions such as Stop, Search, Slow-  
motion Play, Repeat Play, or Random Play  
The disc tray does not open and “LOCK”  
appears on the front panel display.  
, Contact your Sony dealer or local authorized Sony service  
facility.  
cannot be performed.  
, Depending on the disc, you may not be able to do some of  
the operations above. Refer to the operating manual that  
comes with the disc.  
The disc tray does not open and you cannot  
remove the disc even after you press Z.  
The language for the soundtrack cannot be  
, Turn on the player.  
As soon as “POWER ON” appears on the front panel  
display, press x on the player (not the remote) repeatedly  
until the tray opens. Repeat the above procedure several  
times if the tray does not open on the first try.  
changed.  
, Try using the BD’s or DVD’s menu instead of the direct  
selection button on the remote (page 21).  
, Multi-lingual tracks are not recorded on the BD/DVD being  
played.  
, The BD/DVD prohibits the changing of the language for the  
sound track.  
“UNPLAYABLE” appears when playing a DATA  
DVD.  
, The MP3 audio track/JPEG image file you want to play/view  
is damaged.  
, The data is not MPEG-1 Audio Layer III data.  
, The JPEG image file format does not conform to DCF*  
The subtitle language cannot be changed or  
turned off.  
, Try using the BD’s or DVD’s menu instead of the direct  
selection button on the remote (page 21).  
, Multi-lingual subtitles are not recorded on the BD/DVD  
being played.  
, The JPEG image file has the extension “.JPG” or “.JPEG,”  
but is not in JPEG format.  
, The BD/DVD prohibits the changing of subtitles.  
* “Design rule for Camera File system”: Image standards for digital  
cameras regulated by JEITA (Japan Electronics and Information  
Technology Industries Association).  
The angles cannot be changed.  
, Try using the BD’s or DVD’s menu instead of the direct  
selection button on the remote (page 21).  
, Multi-angles are not recorded on the BD/DVD being played.  
, The BD/DVD prohibits changing of the angles.  
The player does not accept any button.  
, Hold down \/1 on the player for more than five seconds  
until the indicators on the front panel display turn off.  
The HDMI Control function does not work.  
, If the HDMI indicator on the front panel does not light up,  
check the HDMI connection (page 11, 15).  
, Set “HDMI Control” to “On” (page 52).  
, Make sure that the connected component is compatible with  
the HDMI Control function. Refer to the operating  
instructions of the component for details.  
, Check that the power cord of the connected component is  
connected securely.  
, Check the connected component’s setting for the HDMI  
Control function. Refer to the operating instructions of the  
component.  
, If you change the HDMI connection, connect and disconnect  
the power cord, or if power failure occurs, set “HDMI  
Control” to “Off,” then set “HDMI Control” to “On”  
, For details on the HDMI Control function, see “About the  
The display language on the screen switches  
automatically.  
, When “HDMI Control” is set to “On” (page 52), the display  
language on the screen automatically switches according to  
the language setting of the connected TV (if you change the  
setting on your TV, etc).  
The player does not operate properly.  
, When static electricity, etc., causes the player to operate  
abnormally, unplug the player.  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Self-Diagnosis Function  
When the self-diagnosis function is activated to prevent the  
player from malfunctioning, the “ERR” error code appears on  
the front panel display indicating the cause.  
Error code  
Cause and/or corrective  
action  
AACS ERR  
AACS read failure.  
tRemove the protected disc.  
LSI1 ERR  
LSI2 ERR  
LSI3 ERR  
MEM ERR  
FLASH ERR  
ROM ERR  
tContact your nearest Sony dealer  
or local authorized Sony service  
facility and give the error code.  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Index to Parts and Controls  
Buttons on the remote and the player have the same function if they have the same or similar name.  
For details, see the pages in parentheses.  
Front panel  
HDMI  
HD  
FL OFF  
A @/1 (20)  
– Turns on the player, or sets to standby mode.  
F HDMI indicator (11)  
– Lights up when an HDMI device is connected.  
HD indicator (11)  
– Lights up when outputting 720p/1080i/1080p  
video signals.  
B Disc tray (20)  
C H, X, x (20)  
– Starts, pauses, or stops playback.  
FL OFF indicator (24)  
– Lights up when the front panel display and other  
indicators on the front panel are turned off.  
D ./> (24)  
– Skips to the previous/next chapter or track.  
– Scans forward or backwards when held down.  
G Remote sensor (16)  
E A (20)  
H Blu-ray Disc indicator  
– Opens or closes the disc tray.  
– Lights up when a BD is recognized.  
– Lights up for a few seconds when the player is  
turned on.  
I Front panel display (59)  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Front panel display  
The playback information is displayed as follows.  
A H  
Example: When playing a DVD VIDEO or a BD-ROM  
– Lights up during playback.  
B Playback information  
z Hint  
You can change the brightness of the front panel display by pressing  
DIMMER (page 24).  
A Current title number  
B Current chapter number  
Note that the chapter number is not displayed if the  
title’s elapsed time exceeds 10 hours.  
C Elapsed time of the title  
Rear panel  
For connections, see page 10 to 16.  
COMPONENT  
VIDEO OUT  
VIDEO  
OUT  
AUDIO  
OUT  
5.1CH OUTPUT  
FRONT REAR CENTER  
Y
P
P
DIGITAL OUT  
VIDEO  
PCM/DTS/DOLBY DIGITAL  
AC IN  
L
L
COAXIAL  
OPTICAL  
B
R
HDMI  
OUT  
R
R
WOOFER  
S
VIDEO  
A AC IN terminal (16)  
F AUDIO OUT (L/R) jacks (13, 14)  
B HDMI OUT jack (11, 12, 15)  
G 5.1CH OUTPUT (FRONT L/R, REAR L/R, CENTER,  
WOOFER) jacks (14)  
C VIDEO OUT (VIDEO/S VIDEO) jacks (10)  
D COMPONENT VIDEO OUT (Y/PB/PR) jacks (10)  
E DIGITAL OUT (COAXIAL/OPTICAL) jacks (13, 14)  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
we have made it clear that any patent must be  
licensed for everyone’s free use or not licensed at  
all.  
The precise terms and conditions for copying,  
distribution and modification follow.  
Program, the distribution of the whole must  
be on the terms of this License, whose  
permissions for other licensees extend to the  
entire whole, and thus to each and every part  
regardless of who wrote it.  
Thus, it is not the intent of this section to  
claim rights or contest your rights to work  
written entirely by you; rather, the intent is  
to exercise the right to control the  
GNU License  
Information  
TERMS AND CONDITIONS FOR COPYING,  
DISTRIBUTION AND MODIFICATION  
0. This License applies to any program or  
other work which contains a notice placed  
by the copyright holder saying it may be  
distributed under the terms of this General  
Public License. The “Program”, below,  
refers to any such program or work, and a  
“work based on the Program” means either  
the Program or any derivative work under  
copyright law: that is to say, a work  
containing the Program or a portion of it,  
either verbatim or with modifications and/or  
translated into another language.  
distribution of derivative or collective  
works based on the Program.  
Regarding the GNU General  
Public License  
In addition, mere aggregation of another  
work not based on the Program with the  
Program (or with a work based on the  
Program) on a volume of a storage or  
distribution medium does not bring the other  
work under the scope of this License.  
3. You may copy and distribute the Program  
(or a work based on it, under Section 2) in  
object code or executable form under the  
terms of Sections 1 and 2 above provided  
that you also do one of the following:  
a) Accompany it with the complete  
corresponding machine-readable  
The software programs used on this component  
include the GNU/Linux system.  
The GNU/Linux system contains software  
licensed for use based on the terms of a GNU  
General Public License. If necessary, the user  
may request the source code for this licensed  
software. The source code is available on our  
website. Access the following URL to download:  
Please refrain from making inquiries about the  
source code content.  
(Hereinafter, translation is included without  
limitation in the term “modification”.) Each  
licensee is addressed as “you”.  
Activities other than copying, distribution  
and modification are not covered by this  
License; they are outside its scope. The act  
of running the Program is not restricted, and  
the output from the Program is covered only  
if its contents constitute a work based on the  
Program (independent of having been made  
by running the Program). Whether that is  
true depends on what the Program does.  
1. You may copy and distribute verbatim  
copies of the Program’s source code as you  
receive it, in any medium, provided that you  
conspicuously and appropriately publish on  
each copy an appropriate copyright notice  
and disclaimer of warranty; keep intact all  
the notices that refer to this License and to  
the absence of any warranty; and give any  
other recipients of the Program a copy of  
this License along with the Program.  
You may charge a fee for the physical act of  
transferring a copy, and you may at your  
option offer warranty protection in  
source code, which must be distributed  
under the terms of Sections 1 and 2  
above on a medium customarily used  
for software interchange; or,  
Details of the GNU General Public License can  
be found at the GNU website  
(http://www.gnu.org).  
b) Accompany it with a written offer,  
valid for at least three years, to give any  
third party, for a charge no more than  
your cost of physically performing  
source distribution, a complete  
GNU General Public License  
Version 2, June 1991  
Copyright (C) 1989, 1991 Free Software  
Foundation, Inc.  
59 Temple Place - Suite 330, Boston, MA 02111-  
1307, USA  
Everyone is permitted to copy and distribute  
verbatim copies of this license document, but  
changing it is not allowed.  
machine-readable copy of the  
corresponding source code, to be  
distributed under the terms of Sections  
1 and 2 above on a medium customarily  
used for software interchange; or,  
c) Accompany it with the information you  
received as to the offer to distribute  
corresponding source code. (This  
Preamble  
The licenses for most software are designed to  
take away your freedom to share and change it.  
By contrast, the GNU General Public License is  
intended to guarantee your freedom to share and  
change free software-to make sure the software is  
free for all its users. This General Public License  
applies to most of the Free Software  
alternative is allowed only for  
noncommercial distribution and only if  
you received the program in object  
code or executable form with such an  
offer, in accord with Subsection b  
exchange for a fee.  
2. You may modify your copy or copies of the  
Program or any portion of it, thus forming a  
work based on the Program, and copy and  
distribute such modifications or work under  
the terms of Section 1 above, provided that  
you also meet all of these conditions:  
a) You must cause the modified files to  
carry prominent notices stating that you  
changed the files and the date of any  
change.  
above.)  
The source code for a work means the  
preferred form of the work for making  
modifications to it. For an executable work,  
complete source code means all the source  
code for all modules it contains, plus any  
associated interface definition files, plus the  
scripts used to control compilation and  
installation of the executable.  
However, as a special exception, the source  
code distributed need not include anything  
that is normally distributed (in either source  
or binary form) with the major components  
(compiler, kernel, and so on) of the  
operating system on which the executable  
runs, unless that component itself  
Foundation’s software and to any other program  
whose authors commit to using it. (Some other  
Free Software Foundation software is covered by  
the GNU Lesser General Public License instead.)  
You can apply it to your programs, too.  
When we speak of free software, we are referring  
to freedom, not price. Our General Public  
Licenses are designed to make sure that you have  
the freedom to distribute copies of free software  
(and charge for this service if you wish), that you  
receive source code or can get it if you want it,  
that you can change the software or use pieces of  
it in new free programs; and that you know you  
can do these things.  
b) You must cause any work that you  
distribute or publish, that in whole or in  
part contains or is derived from the  
Program or any part thereof, to be  
licensed as a whole at no charge to all  
third parties under the terms of this  
To protect your rights, we need to make  
License.  
accompanies the executable.  
restrictions that forbid anyone to deny you these  
rights or to ask you to surrender the rights. These  
restrictions translate to certain responsibilities  
for you if you distribute copies of the software, or  
if you modify it.  
For example, if you distribute copies of such a  
program, whether gratis or for a fee, you must  
give the recipients all the rights that you have.  
You must make sure that they, too, receive or can  
get the source code. And you must show them  
these terms so they know their rights.  
We protect your rights with two steps: (1)  
copyright the software, and (2) offer you this  
license which gives you legal permission to  
copy, distribute and/or modify the software.  
Also, for each author’s protection and ours, we  
want to make certain that everyone understands  
that there is no warranty for this free software. If  
the software is modified by someone else and  
passed on, we want its recipients to know that  
what they have is not the original, so that any  
problems introduced by others will not reflect on  
the original authors’ reputations.  
c) If the modified program normally reads  
commands interactively when run, you  
must cause it, when started running for  
such interactive use in the most  
If distribution of executable or object code  
is made by offering access to copy from a  
designated place, then offering equivalent  
access to copy the source code from the  
same place counts as distribution of the  
source code, even though third parties are  
not compelled to copy the source along with  
the object code.  
ordinary way, to print or display an  
announcement including an  
appropriate copyright notice and a  
notice that there is no warranty (or else,  
saying that you provide a warranty) and  
that users may redistribute the program  
under these conditions, and telling the  
user how to view a copy of this License.  
(Exception: if the Program itself is  
interactive but does not normally print such  
an announcement, your work based on the  
Program is not required to print an  
4. You may not copy, modify, sublicense, or  
distribute the Program except as expressly  
provided under this License. Any attempt  
otherwise to copy, modify, sublicense or  
distribute the Program is void, and will  
automatically terminate your rights under  
this License.  
However, parties who have received copies,  
or rights, from you under this License will  
not have their licenses terminated so long as  
such parties remain in full compliance.  
5. You are not required to accept this License,  
since you have not signed it. However,  
nothing else grants you permission to  
modify or distribute the Program or its  
derivative works. These actions are  
prohibited by law if you do not accept this  
License. Therefore, by modifying or  
distributing the Program (or any work based  
announcement.)  
These requirements apply to the modified  
work as a whole. If identifiable sections of  
that work are not derived from the Program,  
and can be reasonably considered  
independent and separate works in  
themselves, then this License, and its terms,  
do not apply to those sections when you  
distribute them as separate works. But when  
you distribute the same sections as part of a  
whole which is a work based on the  
Finally, any free program is threatened  
constantly by software patents. We wish to avoid  
the danger that redistributors of a free program  
will individually obtain patent licenses, in effect  
making the program proprietary. To prevent this,  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
on the Program), you indicate your  
acceptance of this License to do so, and all  
its terms and conditions for copying,  
distributing or modifying the Program or  
works based on it.  
Software Foundation, write to the Free  
Software Foundation; we sometimes make  
exceptions for this. Our decision will be  
guided by the two goals of preserving the  
free status of all derivatives of our free  
software and of promoting the sharing and  
reuse of software generally.  
If the program is interactive, make it output a  
short notice like this when it starts in an  
interactive mode:  
Gnomovision version 69, Copyright (C)  
year name of author  
6. Each time you redistribute the Program (or  
any work based on the Program), the  
recipient automatically receives a license  
from the original licensor to copy, distribute  
or modify the Program subject to these  
terms and conditions. You may not impose  
any further restrictions on the recipients’  
exercise of the rights granted herein. You  
are not responsible for enforcing  
compliance by third parties to this License.  
7. If, as a consequence of a court judgment or  
allegation of patent infringement or for any  
other reason (not limited to patent issues),  
conditions are imposed on you (whether by  
court order, agreement or otherwise) that  
contradict the conditions of this License,  
they do not excuse you from the conditions  
of this License. If you cannot distribute so as  
to satisfy simultaneously your obligations  
under this License and any other pertinent  
obligations, then as a consequence you may  
not distribute the Program at all. For  
Gnomovision comes with ABSOLUTELY  
NO WARRANTY; for details type ‘show  
w’. This is free software, and you are  
welcome to redistribute it under certain  
conditions; type ‘show c’ for details.  
The hypothetical commands ‘show w’ and ‘show  
c’ should show the appropriate parts of the  
General Public License. Of course, the  
commands you use may be called something  
other than ‘show w’ and ‘show c’; they could  
even be mouse-clicks or menu items-whatever  
suits your program.  
You should also get your employer (if you work  
as a programmer) or your school, if any, to sign  
a “copyright disclaimer” for the program, if  
necessary. Here is a sample; alter the names:  
Yoyodyne, Inc., hereby disclaims all copyright  
interest in the program ‘Gnomovision’ (which  
makes passes at compilers) written by James  
Hacker.  
NO WARRANTY  
11. BECAUSE THE PROGRAM IS  
LICENSED FREE OF CHARGE, THERE  
IS NO WARRANTY FOR THE  
PROGRAM, TO THE EXTENT  
PERMITTED BYAPPLICABLE LAW.  
EXCEPT WHEN OTHERWISE STATED  
IN WRITING THE COPYRIGHT  
HOLDERS AND/OR OTHER PARTIES  
PROVIDE THEPROGRAM “AS IS”  
WITHOUT WARRANTY OF ANY KIND,  
EITHER EXPRESSED OR IMPLIED,  
INCLUDING, BUT NOT LIMITED TO,  
THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS  
FOR A PARTICULAR PURPOSE. THE  
ENTIRE RISK AS TO THE QUALITY  
AND PERFORMANCE OF THE  
PROGRAM IS WITH YOU. SHOULD  
THE PROGRAM PROVE DEFECTIVE,  
YOU ASSUME THE COST OF ALL  
NECESSARY SERVICING, REPAIROR  
CORRECTION.  
signature of Ty Coon, 1 April 1989  
Ty Coon, President of Vice  
example, if a patent license would not  
permit royalty-free redistribution of the  
Program by all those who receive copies  
directly or indirectly through you, then the  
only way you could satisfy both it and this  
License would be to refrain entirely from  
distribution of the Program.  
If any portion of this section is held invalid  
or unenforceable under any particular  
circumstance, the balance of the section is  
intended to apply and the section as a whole  
is intended to apply in other circumstances.  
It is not the purpose of this section to induce  
you to infringe any patents or other property  
right claims or to contest validity of any  
such claims; this section has the sole  
purpose of protecting the integrity of the  
free software distribution system, which is  
implemented by public license practices.  
Many people have made generous  
contributions to the wide range of software  
distributed through that system in reliance  
on consistent application of that system; it is  
up to the author/donor to decide if he or she  
is willing to distribute software through any  
other system and a licensee cannot impose  
that choice.  
This section is intended to make thoroughly  
clear what is believed to be a consequence  
of the rest of this License.  
This General Public License does not permit  
incorporating your program into proprietary  
programs. If your program is a subroutine  
library, you may consider it more useful to  
permit linking proprietary applications with the  
library. If this is what you want to do, use the  
GNU Lesser General Public License instead of  
this License.  
12. IN NO EVENT UNLESS REQUIRED BY  
APPLICABLE LAW OR AGREED TO IN  
WRITING WILL ANY COPYRIGHT  
HOLDER, OR ANY OTHER PARTY  
WHOMAY MODIFY AND/OR  
REDISTRIBUTE THE PROGRAM AS  
PERMITTED ABOVE, BE LIABLE TO  
YOU FOR DAMAGES, INCLUDING  
ANY GENERAL,SPECIAL,  
GNU Lesser General Public  
License  
Version 2.1, February 1999  
INCIDENTAL OR CONSEQUENTIAL  
DAMAGES ARISING OUT OF THE USE  
OR INABILITY TO USE THE PROGRAM  
(INCLUDING BUT NOT LIMITED TO  
LOSS OF DATA OR DATA BEING  
RENDERED INACCURATE OR LOSSES  
SUSTAINED BY YOU OR THIRD  
PARTIES OR A FAILURE OF THE  
PROGRAM TO OPERATE WITH ANY  
OTHER PROGRAMS), EVEN IF SUCH  
HOLDER OR OTHER PARTY HAS  
BEEN ADVISED OF THE POSSIBILITY  
OF SUCH DAMAGES.  
Copyright (C) 1991, 1999 Free Software  
Foundation, Inc.  
59 Temple Place, Suite 330, Boston, MA 02111-  
1307, USA  
Everyone is permitted to copy and distribute  
verbatim copies of this license document, but  
changing it is not allowed.  
[This is the first released version of the Lesser  
GPL. It also counts as the successor of the GNU  
Library Public License, version 2, hence the  
version number2.1.]  
Preamble  
END OF TERMS AND CONDITIONS  
The licenses for most software are designed to  
take away your freedom to share and change it.  
By contrast, the GNU General Public Licenses  
are intended to guarantee your freedom to share  
and change free software-to make sure the  
software is free for all its users. This license, the  
Lesser General Public License, applies to some  
specially designated software packages-typically  
libraries-of the Free Software Foundation and  
other authors who decide to use it. You can use it  
too, but we suggest you first think carefully about  
whether this license or the ordinary General  
Public License is the better strategy to use in any  
particular case, based on the explanations below.  
When we speak of free software, we are referring  
to freedom of use, not price. Our General Public  
Licenses are designed to make sure that you have  
the freedom to distribute copies of free software  
(and charge for this service if you wish); that you  
receive source code or can get it if you want it;  
that you can change the software and use pieces  
of it in new free programs; and that you are  
informed that you can do these things.  
How to Apply These Terms to Your  
New Programs  
If you develop a new program, and you want it to  
be of the greatest possible use to the public, the  
best way to achieve this is to make it free  
software which everyone can redistribute and  
change under these terms.  
To do so, attach the following notices to the  
program. It is safest to attach them to the start of  
each source file to most effectively convey the  
exclusion of warranty; and each file should have  
at least the “copyright” line and a pointer to  
where the full notice is found.  
8. If the distribution and/or use of the Program  
is restricted in certain countries either by  
patents or by copyrighted interfaces, the  
original copyright holder who places the  
Program under this License may add an  
explicit geographical distribution limitation  
excluding those countries, so that  
distribution is permitted only in or among  
countries not thus excluded. In such case,  
this License incorporates the limitation as if  
written in the body of this License.  
9. The Free Software Foundation may publish  
revised and/or new versions of the General  
Public License from time to time. Such new  
versions will be similar in spirit to the  
present version, but may differ in detail to  
address new problems or concerns.  
<one line to give the program’s name and an  
idea of what it does.>  
Copyright (C) yyyy name of author  
This program is free software; you can  
redistribute it and/or modify it under the terms of  
the GNU General Public License as published by  
the Free Software Foundation; either version 2 of  
the License, or (at your option) any later version.  
This program is distributed in the hope that it will  
be useful, but WITHOUT ANY WARRANTY;  
without even the implied warranty of  
MERCHANTABILITY or FITNESS FOR A  
PARTICULAR PURPOSE. See the GNU  
General Public License for more details.  
You should have received a copy of the GNU  
General Public License along with this program;  
if not, write to the Free Software Foundation,  
Inc., 59 Temple Place - Suite 330, Boston, MA  
02111-1307, USA.  
Each version is given a distinguishing  
version number. If the Program specifies a  
version number of this License which  
applies to it and “any later version”, you  
have the option of following the terms and  
conditions either of that version or of any  
later version published by the Free Software  
Foundation. If the Program does not specify  
a version number of this License, you may  
choose any version ever published by the  
Free Software Foundation.  
To protect your rights, we need to make  
restrictions that forbid distributors to deny you  
these rights or to ask you to surrender these  
rights. These restrictions translate to certain  
responsibilities for you if you distribute copies of  
the library or if you modify it.  
For example, if you distribute copies of the  
library, whether gratis or for a fee, you must give  
the recipients all the rights that we gave you. You  
must make sure that they, too, receive or can get  
the source code. If you link other code with the  
library, you must provide complete object files to  
the recipients, so that they can relink them with  
the library after making changes to the library  
10. If you wish to incorporate parts of the  
Program into other free programs whose  
distribution conditions are different, write to  
the author to ask for permission. For  
Also add information on how to contact you by  
electronic and paper mail.  
software which is copyrighted by the Free  
,continued  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
and recompiling it. And you must show them  
these terms so they know their rights.  
“this License”). Each licensee is addressed  
as “you”.  
reasonably considered independent and  
separate works in themselves, then this  
License, and its terms, do not apply to those  
sections when you distribute them as  
separate works. But when you distribute the  
same sections as part of a whole which is a  
work based on the Library, the distribution  
of the whole must be on the terms of this  
license, whose permissions for other  
licensees extend to the entire whole, and  
thus to each and every part regardless of  
who wrote it.  
Thus, it is not the intent of this section to  
claim rights or contest your rights to work  
written entirely by you; rather, the intent is  
to exercise the right to control the  
distribution of derivative or collective  
works based on the Library. In addition,  
mere aggregation of another work not based  
on the Library with the Library (or with a  
work based on the Library) on a volume of a  
storage or distribution medium does not  
bring the other work under the scope of this  
License.  
We protect your rights with a two-step method:  
(1) we copyright the library, and (2) we offer you  
this license, which gives you legal permission to  
copy, distribute and/or modify the library.  
To protect each distributor, we want to make it  
very clear that there is no warranty for the free  
library. Also, if the library is modified by  
someone else and passed on, the recipients  
should know that what they have is not the  
original version, so that the original author’s  
reputation will not be affected by problems that  
might be introduced by others.  
Finally, software patents pose a constant threat to  
the existence of any free program. We wish to  
make sure that a company cannot effectively  
restrict the users of a free program by obtaining a  
restrictive license from a patent holder.  
Therefore, we insist that any patent license  
obtained for a version of the library must be  
consistent with the full freedom of use specified  
in this license. Most GNU software, including  
some libraries, is covered by the ordinary GNU  
General Public License. This license, the GNU  
Lesser General Public License, applies to certain  
designated libraries, and is quite different from  
the ordinary General Public License. We use this  
license for certain libraries in order to permit  
linking those libraries into non-free programs.  
When a program is linked with a library, whether  
statically or using a shared library, the  
combination of the two is legally speaking a  
combined work, a derivative of the original  
library. The ordinary General Public License  
therefore permits such linking only if the entire  
combination fits its criteria of freedom. The  
Lesser General Public License permits more lax  
criteria for linking other code with the library.  
We call this license the “Lesser” General Public  
License because it does Less to protect the user’s  
freedom than the ordinary General Public  
License. It also provides other free software  
developers Less of an advantage over competing  
non-free programs. These disadvantages are the  
reason we use the ordinary General Public  
License for many libraries. However, the Lesser  
license provides advantages in certain special  
circumstances.  
For example, on rare occasions, there may be a  
special need to encourage the widest possible use  
of a certain library, so that it becomes a de facto  
standard. To achieve this, non-free programs  
must be allowed to use the library.  
A more frequent case is that a free library does  
the same job as widely used non-free libraries. In  
this case, there is little to gain by limiting the free  
library to free software only, so we use the Lesser  
General Public License.  
In other cases, permission to use a particular  
library in non-free programs enables a greater  
number of people to use a large body of free  
software. For example, permission to use the  
GNU C Library in non-free programs enables  
many more people to use the whole GNU  
operating system, as well as its variant, the GNU/  
Linux operating system.  
Although the Lesser General Public License is  
Less protective of the users’ freedom, it does  
ensure that the user of a program that is linked  
with the Library has the freedom and the  
wherewithal to run that program using a  
modified version of the Library.  
A “library” means a collection of software  
functions and/or data prepared so as to be  
conveniently linked with application  
programs (which use some of those  
functions and data) to form executables.  
The “Library”, below, refers to any such  
software library or work which has been  
distributed under these terms. A “work  
based on the Library” means either the  
Library or any derivative work under  
copyright law: that is to say, a work  
containing the Library or a portion of it,  
either verbatim or with modifications and/or  
translated straightforwardly into another  
language. (Hereinafter, translation is  
included without limitation in the term  
“modification”.)  
“Source code” for a work means the  
preferred form of the work for making  
modifications to it. For a library, complete  
source code means all the source code for all  
modules it contains, plus any associated  
interface definition files, plus the scripts  
used to control compilation and installation  
of the library.  
3. You may opt to apply the terms of the  
ordinary GNU General Public License  
instead of this License to a given copy of the  
Library. To do this, you must alter all the  
notices that refer to this License, so that they  
refer to the ordinary GNU General Public  
License, version 2, instead of to this  
License. (If a newer version than version 2  
of the ordinary GNU General Public  
License has appeared, then you can specify  
that version instead if you wish.) Do not  
make any other change in these notices.  
Once this change is made in a given copy, it  
is irreversible for that copy, so the ordinary  
GNU General Public License applies to all  
subsequent copies and derivative works  
made from that copy. This option is useful  
when you wish to copy part of the code of  
the Library into a program that is not a  
library.  
4. You may copy and distribute the Library (or  
a portion or derivative of it, under Section 2)  
in object code or executable form under the  
terms of Sections1 and 2 above provided  
that you accompany it with the complete  
corresponding machine-readable source  
code, which must be distributed under the  
terms of Sections 1 and 2 above on a  
medium customarily used for software  
interchange.  
Activities other than copying, distribution  
and modification are not covered by this  
License; they are outside its scope. The act  
of running a program using the Library is  
not restricted, and output from such a  
program is covered only if its contents  
constitute a work based on the Library  
(independent of the use of the Library in a  
tool for writing it). Whether that is true  
depends on what the Library does and what  
the program that uses the Library does.  
1. You may copy and distribute verbatim  
copies of the Library’s complete source  
code as you receive it, in any medium,  
provided that you conspicuously and  
appropriately publish on each copy an  
appropriate copyright notice and disclaimer  
of warranty; keep intact all the notices that  
refer to this License and to the absence of  
any warranty; and distribute a copy of this  
License along with the Library.  
You may charge a fee for the physical act of  
transferring a copy, and you may at your  
option offer warranty protection in  
exchange for a fee.  
2. You may modify your copy or copies of the  
Library or any portion of it, thus forming a  
work based on the Library, and copy and  
distribute such modifications or work under  
the terms of Section 1 above, provided that  
you also meet all of these conditions:  
a) The modified work must itself be a  
software library.  
If distribution of object code is made by  
offering access to copy from a designated  
place, then offering equivalent access to  
copy the source code from the same place  
satisfies the requirement to distribute the  
source code, even though third parties are  
not compelled to copy the source along with  
the object code.  
b) You must cause the files modified to  
carry prominent notices stating that you  
changed the files and the date of any  
change.  
5. A program that contains no derivative of  
any portion of the Library, but is designed to  
work with the Library by being compiled or  
linked with it, is called a “work that uses the  
Library”. Such a work, in isolation, is not a  
derivative work of the Library, and  
c) You must cause the whole of the work  
to be licensed at no charge to all third  
parties under the terms of this License.  
d) If a facility in the modified Library  
refers to a function or a table of data to  
be supplied by an application program  
that uses the facility, other than as an  
argument passed when the facility is  
invoked, then you must make a good  
faith effort to ensure that, in the event  
an application does not supply such  
function or table, the facility still  
therefore falls outside the scope of this  
License. However, linking a “work that uses  
the Library” with the Library creates an  
executable that is a derivative of the Library  
(because it contains portions of the Library),  
rather than a “work that uses the library”.  
The executable is therefore covered by this  
License. Section 6 states terms for  
The precise terms and conditions for copying,  
distribution and modification follow. Pay close  
attention to the difference between a “work based  
on the library” and a “work that uses the library”.  
The former contains code derived from the  
library, whereas the latter must be combined with  
the library in order to run.  
operates, and performs whatever part of  
its purpose remains meaningful.  
distribution of such executables.  
When a “work that uses the Library” uses  
material from a header file that is part of the  
Library, the object code for the work may be  
a derivative work of the Library even  
though the source code is not. Whether this  
is true is especially significant if the work  
can be linked without the Library, or if the  
work is itself a library. The threshold for this  
to be true is not precisely defined by law.  
If such an object file uses only numerical  
parameters, data structure layouts and  
accessors, and small macros and small  
inline functions (ten lines or less in length),  
(For example, a function in a library to  
compute square roots has a purpose that is  
entirely well-defined independent of the  
application. Therefore, Subsection 2d  
requires that any application-supplied  
function or table used by this function must  
be optional: if the application does not  
supply it, the square root function must still  
compute square roots.) These requirements  
apply to the modified work as a whole. If  
identifiable sections of that work are not  
derived from the Library, and can be  
TERMS AND CONDITIONS FOR COPYING,  
DISTRIBUTION AND MODIFICATION  
0. This License Agreement applies to any  
software library or other program which  
contains a notice placed by the copyright  
holder or other authorized party saying it  
may be distributed under the terms of this  
Lesser General Public License (also called  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
then the use of the object file is unrestricted,  
regardless of whether it is legally a  
derivative work. (Executables containing  
this object code plus portions of the Library  
will still fall under Section 6.)  
component itself accompanies the  
executable.  
It is not the purpose of this section to induce  
you to infringe any patents or other property  
right claims or to contest validity of any  
such claims; this section has the sole  
purpose of protecting the integrity of the  
free software distribution system which is  
implemented by public license practices.  
Many people have made generous  
contributions to the wide range of software  
distributed through that system in reliance  
on consistent application of that system; it is  
up to the author/donor to decide if he or she  
is willing to distribute software through any  
other system and a licensee cannot impose  
that choice.  
It may happen that this requirement  
contradicts the license restrictions of  
other proprietary libraries that do not  
normally accompany the operating  
system. Such a contradiction means  
you cannot use both them and the  
Otherwise, if the work is a derivative of the  
Library, you may distribute the object code  
for the work under the terms of Section 6.  
Any executables containing that work also  
fall under Section 6, whether or not they are  
linked directly with the Library itself.  
6. As an exception to the Sections above, you  
may also combine or link a “work that uses  
the Library” with the Library to produce a  
work containing portions of the Library, and  
distribute that work under terms of your  
choice, provided that the terms permit  
modification of the work for the customer’s  
own use and reverse engineering for  
debugging such modifications.  
Library together in an executable that  
you distribute.  
7. You may place library facilities that are a  
work based on the Library side-by-side in a  
single library together with other library  
facilities not covered by this License, and  
distribute such a combined library, provided  
that the separate distribution of the work  
based on the Library and of the other library  
facilities is otherwise permitted, and  
provided that you do these two things:  
a) Accompany the combined library with  
a copy of the same work based on the  
Library, uncombined with any other  
library facilities. This must be  
This section is intended to make thoroughly  
clear what is believed to be a consequence  
of the rest of this License.  
12. If the distribution and/or use of the Library  
is restricted in certain countries either by  
patents or by copyrighted interfaces, the  
original copyright holder who places the  
Library under this License may add an  
explicit geographical distribution limitation  
excluding those countries, so that  
You must give prominent notice with each  
copy of the work that the Library is used in  
it and that the Library and its use are covered  
by this License. You must supply a copy of  
this License. If the work during execution  
displays copyright notices, you must include  
the copyright notice for the Library among  
them, as well as a reference directing the  
user to the copy of this License.  
distributed under the terms of the  
Sections above.  
b) Give prominent notice with the  
combined library of the fact that part of  
it is a work based on the Library, and  
explaining where to find the  
distribution is permitted only in or among  
countries not thus excluded. In such case,  
this License incorporates the limitation as if  
written in the body of this License.  
Also, you must do one of these things:  
a) Accompany the work with the  
complete corresponding machine-  
readable source code for the Library  
including whatever changes were used  
in the work (which must be distributed  
under Sections 1 and 2 above); and, if  
the work is an executable linked with  
the Library, with the complete  
accompanying uncombined form of the  
same work.  
13. The Free Software Foundation may publish  
revised and/or new versions of the Lesser  
General Public License from time to time.  
Such new versions will be similar in spirit to  
the present version, but may differ in detail  
to address new problems or concerns.  
Each version is given a distinguishing  
version number. If the Library specifies a  
version number of this License which  
applies to it and “any later version”, you  
have the option of following the terms and  
conditions either of that version or of any  
later version published by the Free Software  
Foundation. If the Library does not specify  
a license version number, you may choose  
any version ever published by the Free  
Software Foundation.  
8. You may not copy, modify, sublicense, link  
with, or distribute the Library except as  
expressly provided under this License. Any  
attempt otherwise to copy, modify,  
sublicense, link with, or distribute the  
Library is void, and will automatically  
terminate your rights under this License.  
However, parties who have received copies,  
or rights, from you under this License will  
not have their licenses terminated so long as  
such parties remain in full compliance.  
9. You are not required to accept this License,  
since you have not signed it. However,  
nothing else grants you permission to  
modify or distribute the Library or its  
derivative works. These actions are  
prohibited by law if you do not accept this  
License. Therefore, by modifying or  
distributing the Library(or any work based  
on the Library), you indicate your  
machine-readable “work that uses the  
Library”, as object code and/or source  
code, so that the user can modify the  
Library and then relink to produce a  
modified executable containing the  
modified Library. (It is understood that  
the user who changes the contents of  
definitions files in the Library will not  
necessarily be able to recompile the  
application to use the modified  
14. If you wish to incorporate parts of the  
Library into other free programs whose  
distribution conditions are incompatible  
with these, write to the author to ask for  
permission. For software which is  
definitions.)  
b) Use a suitable shared library  
mechanism for linking with the  
Library. A suitable mechanism is one  
that (1) uses at run time a copy of the  
library already present on the user’s  
computer system, rather than copying  
library functions into the executable,  
and (2) will operate properly with a  
modified version of the library, if the  
user installs one, as long as the  
acceptance of this License to do so, and all  
its terms and conditions for copying,  
distributing or modifying the Library or  
works based on it.  
copyrighted by the Free Software  
Foundation, write to the Free Software  
Foundation; we sometimes make exceptions  
for this. Our decision will be guided by the  
two goals of preserving the free status of all  
derivatives of our free software and of  
promoting the sharing and reuse of software  
generally.  
10. Each time you redistribute the Library (or  
any work based on the Library), the  
recipient automatically receives a license  
from the original licensor to copy,  
modified version is interface-  
compatible with the version that the  
work was made with.  
distribute, link with or modify the Library  
subject to these terms and conditions. You  
may not impose any further restrictions on  
the recipients’ exercise of the rights granted  
herein. You are not responsible for  
enforcing compliance by third parties with  
this License.  
NO WARRANTY  
15. BECAUSE THE LIBRARY IS LICENSED  
FREE OF CHARGE, THERE IS NO  
WARRANTY FOR THE LIBRARY, TO  
THE EXTENT PERMITTED BY  
c) Accompany the work with a written  
offer, valid for at least three years, to  
give the same user the materials  
APPLICABLE LAW. EXCEPT WHEN  
OTHERWISE STATED IN WRITING  
THE COPYRIGHT HOLDERS AND/OR  
OTHER PARTIES PROVIDE THE  
LIBRARY “AS IS” WITHOUT  
specified in Subsection 6a, above, for a  
charge no more than the cost of  
performing this distribution.  
11. If, as a consequence of a court judgment or  
allegation of patent infringement or for any  
other reason (not limited to patent issues),  
conditions are imposed on you (whether by  
court order, agreement or otherwise) that  
contradict the conditions of this License,  
they do not excuse you from the conditions  
of this License. If you cannot distribute so as  
to satisfy simultaneously your obligations  
under this License and any other pertinent  
obligations, then as a consequence you may  
not distribute the Library at all.  
d) If distribution of the work is made by  
offering access to copy from a  
WARRANTY OF ANY KIND, EITHER  
EXPRESSED OR IMPLIED,  
designated place, offer equivalent  
access to copy the above specified  
materials from the same place.  
INCLUDING, BUT NOT LIMITED TO,  
THE IMPLIED WARRANTIESOF  
MERCHANTABILITY AND FITNESS  
FOR A PARTICULAR PURPOSE. THE  
ENTIRE RISK AS TO THE QUALITY  
AND PERFORMANCE OF  
THELIBRARY IS WITH YOU. SHOULD  
THE LIBRARY PROVE DEFECTIVE,  
YOU ASSUME THE COST OF ALL  
NECESSARY SERVICING, REPAIR OR  
CORRECTION.  
e) Verify that the user has already  
received a copy of these materials or  
that you have already sent this user a  
copy.  
For an executable, the required form of  
the “work that uses the Library” must  
include any data and utility programs  
needed for reproducing the executable  
from it. However, as a special  
For example, if a patent license would not  
permit royalty-free redistribution of the  
Library by all those who receive copies  
directly or indirectly through you, then the  
only way you could satisfy both it and this  
License would be to refrain entirely from  
distribution of the Library. If any portion of  
this section is held invalid or unenforceable  
under any particular circumstance, the  
balance of the section is intended to apply,  
and the section as a whole is intended to  
apply in other circumstances.  
exception, the materials to be  
16. IN NO EVENT UNLESS REQUIRED BY  
APPLICABLE LAW OR AGREED TO IN  
WRITING WILL ANY COPYRIGHT  
HOLDER, OR ANY OTHER PARTY  
WHOMAY MODIFY AND/OR  
distributed need not include anything  
that is normally distributed (in either  
source or binary form) with the major  
components (compiler, kernel, and so  
on) of the operating system on which  
the executable runs, unless that  
REDISTRIBUTE THE LIBRARY AS  
PERMITTED ABOVE, BE LIABLE TO  
YOU FOR DAMAGES, INCLUDING  
,continued  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ANY GENERAL, SPECIAL,  
3. All advertising materials mentioning  
features or use of this software must display  
the following acknowledgment:  
permitted provided that the following conditions  
are met:  
1. Redistributions of source code must retain  
the copyright notice, this list of conditions  
and the following disclaimer.  
2. Redistributions in binary form must  
reproduce the above copyright notice, this  
list of conditions and the following  
disclaimer in the documentation and/or  
other materials provided with the  
distribution.  
3. All advertising materials mentioning  
features or use of this software must display  
the following acknowledgement:  
“This product includes cryptographic  
software written by Eric Young  
INCIDENTAL OR CONSEQUENTIAL  
DAMAGES ARISING OUT OF THE USE  
OR INABILITY TO USE THE LIBRARY  
(INCLUDING BUT NOTLIMITED TO  
LOSS OF DATA OR DATA BEING  
RENDERED INACCURATE OR LOSSES  
SUSTAINED BY YOU OR THIRD  
PARTIES OR A FAILURE OFTHE  
LIBRARY TO OPERATE WITH ANY  
OTHER SOFTWARE), EVEN IF SUCH  
HOLDER OR OTHER PARTY HAS  
BEEN ADVISED OF THE POSSIBILITY  
OF SUCH DAMAGES.  
“This product includes software developed  
by the OpenSSL Project for use in the  
OpenSSL Toolkit.  
(http://www.openssl.org/)”  
4. The names “OpenSSL Toolkit” and  
“OpenSSL Project” must not be used to  
endorse or promote products derived from  
this software without prior written  
permission.  
For written permission, please contact  
5. Products derived from this software may not  
be called “OpenSSL” nor may “OpenSSL”  
appear in their names without prior written  
permission of the OpenSSL Project.  
6. Redistributions of any form whatsoever  
must retain the following acknowledgment:  
“This product includes software developed  
by the OpenSSL Project for use in the  
OpenSSL Toolkit  
END OF TERMS AND CONDITIONS  
How to Apply These Terms to Your  
New Libraries  
The word 'cryptographic' can be left out if  
the rouines from the library being used are  
not cryptographic related :-).  
If you develop a new library, and you want it to  
be of the greatest possible use to the public, we  
recommend making it free software that  
everyone can redistribute and change. You can  
do so by permitting redistribution under these  
terms (or, alternatively, under the terms of the  
ordinary General Public License).  
To apply these terms, attach the following  
notices to the library. It is safest to attach them to  
the start of each source file to most effectively  
convey the exclusion of warranty; and each file  
should have at least the “copyright” line and a  
pointer to where the full notice is found.  
<one line to give the library’s name and an  
idea of what it does.>  
4. If you include any Windows specific code  
(or a derivative thereof) from the apps  
directory (application code) you must  
include an acknowledgement:  
(http://www.openssl.org/)”  
“This product includes software written by  
Tim Hudson ([email protected])”  
THIS SOFTWARE IS PROVIDED BY THE  
OpenSSL PROJECT “AS IS” AND ANY  
EXPRESSED OR IMPLIED WARRANTIES,  
INCLUDING, BUT NOT LIMITED TO, THE  
IMPLIED WARRANTIES OF  
THIS SOFTWARE IS PROVIDED BY ERIC  
YOUNG ``AS IS'' AND ANY EXPRESS OR  
IMPLIED WARRANTIES, INCLUDING, BUT  
NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY  
AND FITNESS FOR A PARTICULAR  
PURPOSE ARE DISCLAIMED. IN NO  
EVENT SHALL THE AUTHOR OR  
MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR  
PURPOSE ARE DISCLAIMED. IN NO  
EVENT SHALL THE OpenSSL PROJECT OR  
ITS CONTRIBUTORS BE LIABLE FOR ANY  
DIRECT, INDIRECT, INCIDENTAL,  
SPECIAL, EXEMPLARY, OR  
Copyright (C) year name of author  
This library is free software; you can redistribute  
it and/or modify it under the terms of the GNU  
Lesser General Public License as published by  
the Free Software Foundation; either version 2.1  
of the License, or (at your option) any later  
version.  
This library is distributed in the hope that it will  
be useful, but WITHOUT ANY WARRANTY;  
without even the implied warranty of  
MERCHANTABILITY or FITNESS FOR A  
PARTICULAR PURPOSE. See the GNU Lesser  
General Public License for more details.  
You should have received a copy of the GNU  
Lesser General Public License along with this  
library; if not, write to the Free Software  
Foundation, Inc., 59Temple Place, Suite 330,  
Boston, MA 02111-1307, USA  
CONTRIBUTORS BE LIABLE FOR ANY  
DIRECT, INDIRECT, INCIDENTAL,  
SPECIAL, EXEMPLARY, OR  
CONSEQUENTIAL DAMAGES  
(INCLUDING, BUT NOT LIMITED TO,  
PROCUREMENT OF SUBSTITUTE GOODS  
OR SERVICES; LOSS OF USE, DATA, OR  
PROFITS; OR BUSINESS INTERRUPTION)  
HOWEVER CAUSED AND ON ANY  
THEORY OF LIABILITY, WHETHER IN  
CONTRACT, STRICT LIABILITY, OR TORT  
(INCLUDING NEGLIGENCE OR  
OTHERWISE) ARISING IN ANY WAY OUT  
OF THE USE OF THIS SOFTWARE, EVEN IF  
ADVISED OF THE POSSIBILITY OF SUCH  
DAMAGE.  
CONSEQUENTIAL DAMAGES  
(INCLUDING, BUT NOT LIMITED TO,  
PROCUREMENT OF SUBSTITUTE GOODS  
OR SERVICES; LOSS OF USE, DATA, OR  
PROFITS; OR BUSINESS INTERRUPTION)  
HOWEVER CAUSED AND ON ANY  
THEORY OF LIABILITY, WHETHER IN  
CONTRACT, STRICT LIABILITY, OR TORT  
(INCLUDING NEGLIGENCE OR  
OTHERWISE) ARISING IN ANY WAY OUT  
OF THE USE OF THIS SOFTWARE, EVEN IF  
ADVISED OF THE POSSIBILITY OF SUCH  
DAMAGE.  
This product includes cryptographic software  
written by Eric Young ([email protected]).  
This product includes software written by Tim  
Hudson ([email protected]).  
Also add information on how to contact you by  
electronic and paper mail.  
The licence and distribution terms for any  
publically available version or derivative of this  
code cannot be changed. i.e. this code cannot  
simply be copied and put under another  
distribution licence [including the GNU Public  
Licence.]  
You should also get your employer (if you work  
as a programmer) or your school, if any, to sign  
a “copyright disclaimer” for the library, if  
necessary. Here is a sample; alter the names:  
Yoyodyne, Inc., hereby disclaims all copyright  
interest in the library ‘Frob’ (a library for  
tweaking knobs) written by James Random  
Hacker.  
Original SSLeay License  
Original SSLeay  
Copyright (C) 1995-1998 Eric Young  
([email protected]) All rights reserved.  
FreeType  
The FreeType Project is copyright (C) 1996-  
2000 by David Turner, Robert Wilhelm, and  
Werner Lemberg. All rights reserved except as  
specified below.  
signature of Ty Coon, 1 April 1990  
Ty Coon, President of Vice  
That’s all there is to it!  
This package is an SSL implementation written  
by Eric Young ([email protected]).  
The implementation was written so as to conform  
with Netscapes SSL.  
THE FREETYPE PROJECT IS PROVIDED  
‘AS IS’ WITHOUT WARRANTY OF ANY  
KIND, EITHER EXPRESS OR IMPLIED,  
INCLUDING, BUT NOT LIMITED TO,  
WARRANTIES OF MERCHANTABILITY  
AND FITNESS FOR A PARTICULAR  
PURPOSE. IN NO EVENT WILL ANY OF  
THE AUTHORS OR COPYRIGHT HOLDERS  
BE LIABLE FOR ANY DAMAGES CAUSED  
BY THE USE OR THE INABILITY TO USE,  
OF THE FREETYPE PROJECT.  
This library is free for commercial and non-  
commercial use as long as the following  
conditions are aheared to. The following  
conditions apply to all code found in this  
distribution, be it the RC4, RSA, lhash, DES,  
etc., code; not just the SSL code. The SSL  
documentation included with this distribution is  
covered by the same copyright terms except that  
the holder is Tim Hudson ([email protected]).  
OpenSSL License  
OpenSSL  
Copyright (c) 1998-2004 The OpenSSL Project.  
All rights reserved.  
Redistribution and use in source and binary  
forms, with or without modification, are  
permitted provided that the following conditions  
are met:  
1. Redistributions of source code must retain  
the above copyright notice, this list of  
conditions and the following disclaimer.  
2. Redistributions in binary form must  
reproduce the above copyright notice, this  
list of conditions and the following  
disclaimer in the documentation and/or  
other materials provided with the  
distribution.  
Copyright remains Eric Young's, and as such any  
Copyright notices in the code are not to be  
removed.  
If this package is used in a product, Eric Young  
should be given attribution as the author of the  
parts of the library used.  
This can be in the form of a textual message at  
program startup or in documentation (online or  
textual) provided with the package.  
Howl  
Copyright (c) 2003, 2004 Porchdog Software All  
rights reserved.  
THIS SOFTWARE IS PROVIDED BY THE  
COPYRIGHT HOLDERS AND  
CONTRIBUTORS “AS IS” AND ANY  
EXPRESS OR IMPLIED WARRANTIES,  
INCLUDING, BUT NOT LIMITED TO, THE  
IMPLIED WARRANTIES OF  
Redistribution and use in source and binary  
forms, with or without modification, are  
MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE ARE  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DISCLAIMED. IN NO EVENT SHALL THE  
COPYRIGHT OWNER OR CONTRIBUTORS  
BE LIABLE FOR ANY DIRECT, INDIRECT,  
INCIDENTAL, SPECIAL, EXEMPLARY, OR  
CONSEQUENTIAL DAMAGES  
(INCLUDING, BUT NOT LIMITED TO,  
PROCUREMENT OF SUBSTITUTE GOODS  
OR SERVICES; LOSS OF USE, DATA, OR  
PROFITS; OR BUSINESS INTERRUPTION)  
HOWEVER CAUSED AND ON ANY  
THEORY OF LIABILITY, WHETHER IN  
CONTRACT, STRICT LIABILITY, OR TORT  
(INCLUDING NEGLIGENCE OR  
libpng versions 0.5, May 1995, through 0.88,  
January 1996, are Copyright (c) 1995, 1996 Guy  
Eric Schalnat, Group 42, Inc.  
Luxi fonts copyright (c) 2001 by Bigelow &  
Holmes Inc. Luxi font instruction code copyright  
(c) 2001 by URW++ GmbH. All Rights  
Reserved. Luxi is a registered trademark of  
Bigelow & Holmes Inc.  
For the purposes of this copyright and license,  
“Contributing Authors” is defined as the  
following set of individuals:  
THE FONT SOFTWARE IS PROVIDED “AS  
IS”, WITHOUT WARRANTY OF ANY KIND,  
EXPRESS OR IMPLIED, INCLUDING BUT  
NOT LIMITED TO ANY WARRANTIES OF  
MERCHANTABILITY, FITNESS FOR A  
PARTICULAR PURPOSE AND  
Andreas Dilger  
Dave Martindale  
Guy Eric Schalnat  
Paul Schmidt  
OTHERWISE) ARISING IN ANY WAY OUT  
OF THE USE OF THIS SOFTWARE, EVEN IF  
ADVISED OF THE POSSIBILITY OF SUCH  
DAMAGE.  
Tim Wegner  
NONINFRINGEMENT OF COPYRIGHT,  
PATENT, TRADEMARK, OR OTHER  
RIGHT. IN NO EVENT SHALL BIGELOW &  
HOLMES INC. OR URW++ GMBH. BE  
LIABLE FOR ANY CLAIM, DAMAGES OR  
OTHER LIABILITY, INCLUDING ANY  
GENERAL, SPECIAL, INDIRECT,  
INCIDENTAL, OR CONSEQUENTIAL  
DAMAGES, WHETHER IN AN ACTION OF  
CONTRACT, TORT OR OTHERWISE,  
ARISING FROM, OUT OF THE USE OR  
INABILITY TO USE THE FONT SOFTWARE  
OR FROM OTHER DEALINGS IN THE FONT  
SOFTWARE.  
The PNG Reference Library is supplied “AS IS”.  
The Contributing Authors and Group 42, Inc.  
disclaim all warranties, expressed or implied,  
including, without limitation, the warranties of  
merchantability and of fitness for any purpose.  
The Contributing Authors and Group 42, Inc.  
assume no liability for direct, indirect, incidental,  
special, exemplary, or consequential damages,  
which may result from the use of the PNG  
Reference Library, even if advised of the  
possibility of such damage.  
jpeg-6b  
If only executable code is distributed, then the  
accompanying documentation must state that  
“this software is based in part on the work of the  
Independent JPEG Group”.  
libpng  
COPYRIGHT NOTICE, DISCLAIMER, and  
LICENSE:  
Permission is hereby granted to use, copy,  
modify, and distribute this source code, or  
portions hereof, for any purpose, without fee,  
subject to the following restrictions:  
TIFF  
If you modify libpng you may insert additional  
notices immediately following this sentence.  
Copyright (c) 1988-1997 Sam Leffler  
Copyright (c) 1991-1997 Silicon Graphics, Inc.  
1. The origin of this source code must not be  
misrepresented.  
2. Altered versions must be plainly marked as  
such and must not be misrepresented as  
being the original source.  
3. This Copyright notice may not be removed  
or altered from any source or altered source  
distribution.  
libpng version 1.2.6, December 3, 2004, is  
Copyright (c) 2004 Glenn Randers-Pehrson, and  
is distributed according to the same disclaimer  
and license as libpng-1.2.5 with the following  
individual added to the list of Contributing  
Authors  
THE SOFTWARE IS PROVIDED “AS-IS”  
AND WITHOUT WARRANTY OF ANY  
KIND, EXPRESS, IMPLIED OR  
OTHERWISE, INCLUDING WITHOUT  
LIMITATION, ANY WARRANTY OF  
MERCHANTABILITY OR FITNESS FOR A  
PARTICULAR PURPOSE.  
Cosmin Truta  
IN NO EVENT SHALL SAM LEFFLER OR  
SILICON GRAPHICS BE LIABLE FOR ANY  
SPECIAL, INCIDENTAL, INDIRECT OR  
CONSEQUENTIAL DAMAGES OF ANY  
KIND, OR ANY DAMAGES WHATSOEVER  
RESULTING FROM LOSS OF USE, DATA  
OR PROFITS, WHETHER OR NOT ADVISED  
OF THE POSSIBILITY OF DAMAGE, AND  
ON ANY THEORY OF LIABILITY, ARISING  
OUT OF OR IN CONNECTION WITH THE  
USE OR PERFORMANCE OF THIS  
The Contributing Authors and Group 42, Inc.  
specifically permit, without fee, and encourage  
the use of this source code as a component to  
supporting the PNG file format in commercial  
products. If you use this source code in a product,  
acknowledgment is not required but would be  
appreciated.  
libpng versions 1.0.7, July 1, 2000, through 1.2.5  
- October 3, 2002, are Copyright (c) 2000-2002  
Glenn Randers-Pehrson, and are distributed  
according to the same disclaimer and license as  
libpng-1.0.6 with the following individuals  
added to the list of Contributing Authors  
Simon-Pierre Cadieux  
Eric S. Raymond  
Gilles Vollant  
A “png_get_copyright” function is available, for  
convenient use in “about” boxes and the like:  
SOFTWARE.  
printf(“%s”,png_get_copyright(NULL));  
and with the following additions to the  
disclaimer:  
Also, the PNG logo (in PNG format, of course) is  
supplied in the files “pngbar.png” and  
“pngbar.jpg (88x31) and “pngnow.png” (98x31).  
This software is based in part on zlib see http://  
There is no warranty against interference  
with your enjoyment of the library or  
against infringement. There is no warranty  
that our efforts or the library will fulfill any  
of your particular purposes or needs. This  
library is provided with all faults, and the  
entire risk of satisfactory quality,  
This software is based in part on Mozilla Public  
for information.  
Libpng is OSI Certified Open Source Software.  
OSI Certified Open Source is a certification mark  
of the Open Source Initiative.  
This software is based in part on Apple Public  
Source License or the reciient's rights thereunder  
Glenn Randers-Pehrson  
glennrp at users.sourceforge.net  
December 3, 2004  
performance, accuracy, and effort is with  
the user.  
libpng versions 0.97, January 1998, through  
1.0.6, March 20, 2000, are Copyright (c) 1998,  
1999 Glenn Randers-Pehrson, and are distributed  
according to the same disclaimer and license as  
libpng-0.96, with the following individuals  
added to the list of Contributing Authors:  
This software is based in part on Intel License see  
Libungif  
The GIFLIB distribution is Copyright (c) 1997  
Eric S. Raymond  
TinyLogin  
THE SOFTWARE IS PROVIDED “AS IS”,  
WITHOUT WARRANTY OF ANY KIND,  
EXPRESS OR IMPLIED, INCLUDING BUT  
NOT LIMITED TO THE WARRANTIES OF  
MERCHANTABILITY, FITNESS FOR A  
PARTICULAR PURPOSE AND  
NONINFRINGEMENT. IN NO EVENT  
SHALL THE AUTHORS OR COPYRIGHT  
HOLDERS BE LIABLE FOR ANY CLAIM,  
DAMAGES OR OTHER LIABILITY,  
WHETHER IN AN ACTION OF CONTRACT,  
TORT OR OTHERWISE, ARISING FROM,  
OUT OF OR IN CONNECTION WITH THE  
SOFTWARE OR THE USE OR OTHER  
DEALINGS IN THE SOFTWARE.  
This software is copyright 1988 - 1994, Julianne  
Frances Haugh. All rights reserved.  
Tom Lane  
Glenn Randers-Pehrson  
Willem van Schaik  
The shadow utilities license  
This software is copyright 1988 - 1994, Julianne  
Frances Haugh. All rights reserved.  
libpng versions 0.89, June 1996, through 0.96,  
May 1997, are Copyright (c) 1996, 1997 Andreas  
Dilger  
Distributed according to the same disclaimer and  
license as libpng-0.88, with the following  
individuals added to the list of Contributing  
Authors:  
Vera.ttf/VeraMono.ttf  
Copyright © 2003 by Bitstream, Inc. All Rights  
Reserved. Bitstream Vera  
SansBitstreamVeraSans-RomanRelease 1.10  
Copyright © 2003 by Bitstream, Inc. All Rights  
Reserved. Bitstream Vera is a trademark of  
Bitstream, Inc.  
John Bowler  
Kevin Bracey  
Sam Bushell  
Magnus Holmgren  
Greg Roelofs  
Tom Tanner  
Luxi font  
Bigelow & Holmes Inc and URW++ GmbH Luxi  
font license  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dolby TrueHD (page 48)  
BD-ROMs (Blu-ray Disc Read-Only  
Memory) are commercially produced  
discs and are available in the same  
capacities as the BD below. Other than  
conventional movie and video contents,  
these discs have enhanced features such  
as interactive content, menu operations  
using pop-up menus (see below),  
selection of subtitle display, and  
slideshow. Although a BD-ROM may  
contain any form of data, most BD ROM  
discs will contain movies in High  
Definition format, for playback on Blu-  
ray Disc players.  
Dolby TrueHD is a lossless coding  
technology that supports up to 8  
channels of multi-channel surround  
sound for the next generation optical  
discs. The reproduced sound is true to  
the original source bit-for-bit.  
Glossary  
AACS  
“Advanced Access Content System” is a  
specification for managing digital  
entertainment contents stored on the next  
generation of prerecorded and recorded  
optical media. The specification enables  
consumers to enjoy digital entertainment  
content, including high-definition  
content.  
Digital audio compression technology  
that DTS, Inc. developed. This  
technology conforms to multi-channel  
surround sound. The rear channel is  
stereo and there is a discrete subwoofer  
channel in this format. DTS provides the  
same discrete channels of high quality  
digital audio.  
Blu-ray Disc (BD) (page 5)  
Good channel separation is realized  
because all of the channel data is  
recorded discretely and little  
deterioration occurs because all channel  
data processing is digital.  
A disc format developed for recording/  
playing high-definition (HD) video (for  
HDTV, etc.), and for storing large  
amounts of data. A single layer Blu-ray  
Disc holds up to 25 GB, and a dual-layer  
Blu-ray Disc holds up to 50 GB of data.  
The AVCHD format is a high definition  
digital video camera format used to  
record SD (standard definition) or HD  
(high definition) signals of either the  
1
1080i specification* or the 720p  
2
specification* on DVDs, using efficient  
DTS-HD is an extended format of the  
Coherent Acoustics audio coding  
system, which also encompasses DTS  
Digital Surround, DTS-ES, and DTS 96/  
24. DTS-HD is highly flexible in  
supporting the number of discrete  
surround sound channels. While 7.1ch  
surround sound is planned for Blu-ray  
Discs, the audio signals can be  
Chapter (page 25)  
data compression coding technology.  
The MPEG-4 AVC/H.264 format is  
adopted to compress video data, and the  
Dolby Digital or Linear PCM is used to  
compress audio data. The MPEG-4  
AVC/H.264 format is capable of  
compressing images at higher efficiency  
than that of the conventional image  
compression format. The MPEG-4  
AVC/ H.264 format enables a high  
definition (HD) video signal shot on a  
digital video camera recorder to be  
recorded on DVDs in the same way as  
for a standard definition (SD) television  
Sections of a picture or a music feature  
that are smaller than titles. A title is  
composed of several chapters.  
Depending on the disc, no chapters may  
be recorded.  
Dolby Digital (page 47)  
Digital audio compression technology  
developed by Dolby Laboratories. This  
technology conforms to multi-channel  
surround sound. The rear channel is  
stereo and there is a discrete subwoofer  
channel in this format. Dolby Digital  
provides the same discrete channels of  
high quality digital audio found in  
“Dolby Digital” theater surround sound  
systems. Good channel separation is  
realized because all of the channel data is  
recorded discretely and little  
downmixed to 5.1 or 2 channels for  
backward compatibility, and the  
reproduced audio quality can either be at  
the bit rate of DTS Digital Surround or  
the lossless mode.  
signal.  
DVD VIDEO (page 5)  
1
*
A high definition specification that  
utilizes1080 effective scanning lines and  
the interlace format.  
A high definition specification that utilizes  
720 effective scanning lines and the  
progressive format.  
A disc format that contains up to eight  
hours of moving pictures on a disc the  
same diameter as a CD. A single-layer  
single sided DVD holds up to 4.7 GB; a  
double layer single-sided DVD, 8.5 GB;  
a single layer double-sided DVD, 9.4  
GB; double-layer double-sided DVD, 17  
GB. The MPEG 2 format is adopted for  
the efficient video data compression.  
The variable rate coding technology that  
changes the data to be allocated  
2
*
deterioration occurs because all channel  
data processing is digital.  
BD-J application  
Dolby Digital Plus (page 48)  
Developed as an extension to Dolby  
Digital, the audio coding technology  
supports 7.1 multi-channel surround  
sound.  
The BD-ROM format supports Java for  
interactive functions.  
“BD-J” offers content providers almost  
unlimited functionality when creating  
interactive BD-ROM titles.  
according to the status of the picture is  
adopted for reproducing high-quality  
pictures. Audio information is recorded  
in a multi-channel format, such as Dolby  
Digital, allowing for a realistic audio  
presence.  
Dolby Surround (Pro Logic)  
BD-R  
BD-R (Blu-ray Disc Recordable) is a  
recordable, write-once Blu-ray Disc,  
available in the same capacities as the  
BD below. Since contents can be  
recorded and cannot be overwritten, a  
BD-R can be used to archive valuable  
data or storing and distributing video  
material.  
Audio signal processing technology that  
Dolby Laboratories developed for  
surround sound. When the input signal  
contains a surround component, the Pro  
Logic process outputs the front, center  
and rear signals. The rear channel is  
monaural.  
BD-RE  
BD-RE (Blu-ray Disc Rewritable) is a  
recordable and rewritable Blu-ray Disc,  
available in the same capacities as the  
BD below. The re-recordable feature  
makes extensive editing and time-  
shifting applications possible.  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                       
Interlace format  
A DVD-R is a recordable disc that is the  
same size as a DVD VIDEO. Contents  
can be recorded only once to a DVD-R,  
and will have the same format as a DVD  
VIDEO. The DVD-R has two different  
modes: VR mode and Video mode.  
DVDs created in Video mode have the  
same format as a DVD VIDEO, while  
discs created in VR (Video Recording)  
mode allow the contents to be  
Interlace format shows every other line  
of an image as a single “field” and is the  
standard method for displaying images  
on television. The even number field  
shows the even numbered lines of an  
image, and the odd numbered field  
shows the odd numbered lines of an  
image.  
Specifications  
System  
Laser: Semiconductor laser  
MPEG-2  
Outputs  
programmed or edited.  
One of the video data compression  
schemes established by the Moving  
Picture Experts Group (MPEG), which is  
adopted for DVD VIDEOs and digital  
broadcasts worldwide. The scheme  
specifies MPEG-2 PS (Program Stream)  
for recordable media such as a DVD  
VIDEO, and MPEG-2 TS (Transport  
Stream) for digital broadcasts and other  
communications.  
(Jack name: Jack type/Output level/  
Load impedance)  
AUDIO OUT L/R:  
A DVD-RW is a recordable and  
rewritable disc that is the same size as a  
DVD VIDEO. The DVD-RW has two  
different modes: VR mode and Video  
mode. DVDs created in Video mode  
have the same format as a DVD VIDEO,  
while discs created in VR (Video  
Recording) mode allow the contents to  
be programmed or edited.  
Phono jack/2 Vrms/10 kilohms  
DIGITAL OUT (OPTICAL):  
Optical output jack/–18 dBm (wave  
length 660 nm)  
DIGITAL OUT (COAXIAL):  
Phono jack/0.5 Vp-p/75 ohms  
5.1CH OUTPUT:  
Phono jack/2 Vrms/10 kilohms  
HDMI OUT:  
HDMI 19-pin standard connector  
COMPONENT VIDEO OUT(Y, PB,  
PR):  
Pop-up menu  
An enhanced menu operation available  
on BD-ROMs. The pop-up menu  
appears when MENU is pressed during  
playback, and can be operated while  
playback is in progress.  
A DVD+R (read “plus R”) is a  
recordable disc that is the same size as a  
DVD VIDEO. Contents can be recorded  
only once to a DVD+R, and will have the  
same format as a DVD VIDEO.  
Phono jack/Y: 1.0 Vp-p/PB, PR:  
progressive or interlace  
= 0.7 Vp-p/75 ohms  
Progressive format  
VIDEO: Phono jack/1.0 Vp-p/75 ohms  
S VIDEO: 4-pin mini DIN/Y:  
1.0 Vp-p, C: 0.286 Vp-p/75 ohms  
Compared to the Interlace format that  
alternately shows every other line of an  
image (field) to create one frame, the  
Progressive format shows the entire  
image at once as a single frame. This  
means that while the Interlace format can  
show 30 frames/60 fields in one second,  
the Progressive format can show 60  
frames in one second. The overall  
picture quality increases and still images,  
text, and horizontal lines appear sharper.  
A DVD+RW (read “plus RW”) is a  
recordable and rewritable disc.  
DVD+RWs use a recording format that  
is comparable to the DVD VIDEO  
format.  
General  
Power requirements:  
120 V AC, 60 Hz  
Power consumption: 33 W  
Film-based software, Video-based  
software  
Dimensions (approx.):  
1
430 × 79 × 375 mm (17 × 3 / ×  
8
7
14 / in.) (width/height/depth) incl.  
DVDs can be classified as Film-based or  
Video-based software. Film-based  
DVDs contain the same images (24  
frames per second) that are shown at  
movie theaters. Video-based DVDs,  
such as television dramas or sitcoms,  
display images at 30 frames (or 60  
fields) per second.  
8
projecting parts  
Mass (approx.): 4.5 kg (10 lb)  
Operating temperature:  
5 ºC to 35 ºC (41°F to 95°F)  
Operating humidity:  
25 % to 80 %  
The longest section of a picture or music  
feature on a DVD, movie, etc., in video  
software, or the entire album in audio  
software.  
Supplied accessories  
See page 9.  
HDMI (High-Definition Multimedia  
Interface)  
Specifications and design are subject to  
change without notice.  
HDMI is an interface that supports both  
video and audio on a single digital  
connection. The HDMI connection  
carries standard to high definition video  
signals and multi-channel audio signals  
to AV components such as HDMI  
equipped TVs, in digital form without  
degradation.  
The HDMI specification supports HDCP  
(High-bandwidth Digital Contents  
Protection), a copy protection  
technology for digital entertainment  
contents for HDMI.  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
Language (abbr.)  
Hindi (hi)  
Code  
0809  
0818  
0821  
0825  
0901  
0905  
0911  
0914  
0919  
0923  
1009  
1023  
1101  
1111  
1112  
1113  
1114  
1119  
1121  
1125  
1201  
1214  
1215  
1220  
1222  
1307  
1309  
1311  
1312  
1314  
1315  
1318  
1319  
1320  
1325  
1401  
1405  
1415  
1503  
1513  
1518  
1601  
1612  
1619  
1620  
1721  
1813  
1814  
1815  
1823  
1901  
1904  
1907  
1908  
Language (abbr.)  
Sinhalese (si)  
lovak (sk)  
Code  
1909  
1911  
1912  
1913  
1914  
1915  
1917  
1918  
1919  
1920  
1921  
1922  
1923  
2001  
2005  
2007  
2008  
2009  
2011  
2012  
2014  
2015  
2018  
2019  
2020  
2023  
2111  
2118  
2126  
2209  
2215  
2315  
2408  
2515  
2621  
Language Code  
List  
Croatian (hr)  
Hungarian (hu)  
Armenian (hy)  
Interlingua (ia)  
Interlingue (ie)  
Inupiak (ik)  
Slovenian (sl)  
Samoan (sm)  
Shona (sn)  
For details, see page 49.  
Somali (so)  
Albanian (sq)  
Serbian (sr)  
Siswati (ss)  
Sesotho (st)  
Sundanese (su)  
Swedish (sv)  
Swahili (sw)  
Tamil (ta)  
Language (abbr.)  
Japanese (ja)  
English (en)  
French (fr)  
Code  
1001  
0514  
0618  
0405  
0920  
0519  
1412  
1821  
2608  
1115  
0512  
0101  
0102  
0106  
0113  
0118  
0119  
0125  
0126  
0201  
0205  
0207  
0208  
0209  
0214  
0215  
0218  
0301  
0315  
0319  
0325  
0401  
0426  
0515  
0520  
0521  
0601  
0609  
0610  
0615  
0625  
0701  
0704  
0712  
0714  
0721  
0801  
Indonesian (in)  
Icelandic (is)  
Hebrew (iw)  
Yiddish (ji)  
German (de)  
Italian (it)  
Javanese (jw)  
Georgian (ka)  
Kazakh (kk)  
Spanish (es)  
Dutch (nl)  
Russian (ru)  
Chinese (zh)  
Korean (ko)  
Greek (el)  
Greenlandic (kl)  
Cambodian (km)  
Kannada (kn)  
Kashmiri (ks)  
Kurdish (ku)  
Kirghiz (ky)  
Telugu (te)  
Tajik (tg)  
Thai (th)  
Tigrinya (ti)  
Turkmen (tk)  
Tagalog (tl)  
Setswana (tn)  
Tonga (to)  
Afar (aa)  
Abkhazian (ab)  
Afrikaans (af)  
Amharic (am)  
Arabic (ar)  
Latin (la)  
Lingala (ln)  
Laothian (lo)  
Lithuanian (lt)  
Latvian (lv)  
Turkish (tr)  
Tsonga (ts)  
Tatar (tt)  
Assamese (as)  
Aymara (ay)  
Azerbaijani (az)  
Bashkir (ba)  
Byelorussian (be)  
Bulgarian (bg)  
Bihari (bh)  
Malagasy (mg)  
Maori (mi)  
Twi (tw)  
Ukrainian (uk)  
Urdu (ur)  
Macedonian (mk)  
Malayalam (ml)  
Mongolian (mn)  
Moldavian (mo)  
Marathi (mr)  
Malay (ms)  
Uzbek (uz)  
Vietnamese (vi)  
Volapük (vo)  
Wolof (wo)  
Xhosa (xh)  
Yoruba (yo)  
Zulu (zu)  
Bislama (bi)  
Bengali (bn)  
Tibetan (bo)  
Breton (br)  
Maltese (mt)  
Burmese (my)  
Nauru (na)  
Catalan (ca)  
Corsican (co)  
Czech (cs)  
Nepali (ne)  
Welsh (cy)  
Norwegian (no)  
Occitan (oc)  
Danish (da)  
Bhutani (dz)  
Esperanto (eo)  
Estonian (et)  
Basque (eu)  
Persian (fa)  
Finnish (fi)  
Oromo (om)  
Oriya (or)  
Panjabi (pa)  
Polish (pl)  
Pashto, Pushto (ps)  
Portuguese (pt)  
Quechua (qu)  
Rhaeto-Romance (rm)  
Kirundi (rn)  
Fiji (fj)  
Faroese (fo)  
Frisian (fy)  
Irish (ga)  
Romanian (ro)  
Kinyarwanda (rw)  
Sanskrit (sa)  
Scots-Gaelic (gd)  
Galician (gl)  
Guarani (gn)  
Gujarati (gu)  
Hausa (ha)  
Sindhi (sd)  
Sangho (sg)  
Serbo-Croatian (sh)  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Parental Control  
Country/Area  
Code List  
For details, see pages 50 and 52.  
Area (abbr.)  
Argentina (ar)  
Australia (au)  
Austria (at)  
Code  
0118  
0121  
0120  
0205  
0218  
0301  
0312  
0314  
0411  
0609  
0618  
0405  
0811  
0914  
0904  
0920  
1016  
1118  
1325  
1324  
1412  
1426  
1415  
1611  
1608  
1620  
1821  
1907  
0519  
0308  
1905  
2023  
2008  
0702  
Belgium (be)  
Brazil (br)  
Canada (ca)  
Chile (cl)  
China (cn)  
Denmark (dk)  
Finland (fi)  
France (fr)  
Germany (de)  
Hong Kong (hk)  
India (in)  
Indonesia (id)  
Italy (it)  
Japan (jp)  
Korea, Republic of (kr)  
Malaysia (my)  
Mexico (mx)  
Netherlands (nl)  
New Zealand (nz)  
Norway (no)  
Pakistan (pk)  
Philippines (ph)  
Portugal (pt)  
Russian Federation (ru)  
Singapore (sg)  
Spain (es)  
Switzerland (ch)  
Sweden (se)  
Taiwan (tw)  
Thailand (th)  
United Kingdom (gb)  
United States of America 2119  
(us)  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
L
“Language” 49  
Index  
M
“Memory” 28  
“Movies” 32  
MPEG 32  
“Music” 36  
Words in quotations appear in the on-  
screen displays.  
O
Numerics  
5.1CH OUTPUT 14, 51  
“Options” 52  
P
A
“Parental Control” 50  
“Photos” 40  
“A/V Control” 22  
AACS 66  
POP UP/MENU 25  
Pro Logic 14, 47, 66  
Progressive format 67  
ANGLE 24  
AUDIO 24  
“Audio Control” 27  
“Audio Output Mode” 51  
“Audio Setup” 47  
AVCHD 6, 66  
R
Region code 7  
Remote 16, 17, 24  
Resetting the Player 53  
B
Batteries 16  
S
Blu-ray Disc 5, 66  
Searching 26, 34, 38, 42  
‘BRAVIA’ Theatre Sync 11  
“Setup” 22  
Setup Displays 44  
“Slideshow” 41  
“Speaker Setup” 51  
“Speakers” 12, 51  
SUBTITLE 24  
C
CD 5  
Chapter 66  
Color buttons 24  
Connecting  
the audio cords 12  
the video cords 10  
T
Title 67  
Title List 22  
TOP MENU 25  
Troubleshooting 54  
“TV Type” 45  
D
DIMMER 24  
Disc Information 26  
DISPLAY 24  
Display  
U
front panel display 59  
Dolby Digital 14, 47, 66  
Dolby Digital Plus 48, 66  
Dolby TrueHD 48, 66  
DTS 47, 66  
Usable discs 5  
V
Video based software 67  
“Video Control” 28  
“Video Setup” 45  
“DTS Downmix” 47  
DTS-HD 48, 66  
DVD VIDEO 66  
DVD+R 67  
DVD+RW 67  
DVD-R 67  
DVD-RW 67  
E
Easy Setup 18  
F
Film based software 67  
Front panel display 59  
H
HDMI 11, 12, 18, 45, 47, 67  
HDMI Control 11, 21, 52  
I
Interlace format 67  
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sharp Car Stereo System CD C482 User Manual
Sharp CRT Television 54GS 61S User Manual
Sherwood Stereo System RD 6513 User Manual
SonicWALL Sleep Apnea Machine SonicWALL SSL VPN 55 User Manual
Sony Car Satellite TV System KV 27FS120 User Manual
Sony Car Speaker MEX BT2800 User Manual
Sony DVD Recorder 3 293 880 111 User Manual
Sony Water Dispenser 2 User Manual
SpeakerCraft Car Speaker BassX W10 User Manual
SVAT Electronics DVR CVDVR900 User Manual