Sonance Speaker 91922 User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
S O NA N C E EL L IP SE L C R I N-C EI L I NG SP EA K E R  
PN. 33-2528  
INTRODUCTION  
RECOMMENDED PLACEMENT CONTINUED  
Thank you for purchasing the Sonance Ellipse LCR in-ceiling speaker.  
When properly installed, this product will provide you with years of  
entertainment pleasure.  
Proper placement of the Ellipse LCR is critical for maximum  
performance. Try to apply as many of the following recommendations  
in your installation.  
To obtain the full potential of your new speakers, please read all  
instructions before starting the installation. If you do not have the  
necessary skills to install the speakers yourself, contact your  
authorized Sonance dealer for installation options.  
The speakers should be located from eight to eighteen feet from the  
listener. The minimum recommended spacing from speaker to listening  
position would be approximately 6 feet in a room with eight foot  
ceilings. The height and size of the television will largely determine this  
distance. Keep in mind that if the television is placed at eye level and  
the speakers are installed less than six feet in front of the listening  
position the picture and sound could seem very disconnected.  
If possible the speakers should be located a minimum of three to four  
feet from the front wall this is the wall the television is on.  
PARTS LIST  
Each Ellipse speaker package includes the following items:  
(1) Sonance Ellipse LCR speaker  
The left and right speakers should be separated approximately eight to  
twelve feet apart with the center speaker placed as close to the middle  
as possible. The Sonic Eye on all three speakers should be pivoted  
toward the listening position.  
(1) Paintable grille  
(1) Plastic paint plug to protect speaker during painting  
(1) Mounting cutout template ( in packaging )  
8 to 18 feet  
OPTIONAL ACCESSORIES  
FlexBracket - part number 91922  
Plastic template to reserve a hole in new construction.  
Designed to be used with the Flexbar mountinTgM system.  
Acoustical Enclosure - part number 91921  
A 1/2" medium density fiberboard enclosure designed  
specifically for the Ellipse LCR speaker.  
TV  
Sonafill in-ceiling - part number 91928  
Sonafill is a retrofitable acoustical treatment for that virtually  
eliminates the noise produced by resonating drywall and  
dramatically improves mid-bass sound quality  
RECOMMENDED PLACEMENT  
The design of many homes today leaves little space for box or in-wall  
LCR speakers. The use of in-ceiling LCR speakers has become quite  
common in the last few years. Most of these installations have used  
speakers not well suited for this purpose. The Ellipse LCR was  
specifically designed to solve this problem.  
3 to 4 feet  
8 to 18 feet  
The most important consideration when using in-ceiling LCR speakers  
is maintaining good cohesion between picture and sound. As a general  
rule you should try to install the speakers no more than 4 to 6 feet  
away from the top of the television. In a room with 8 foot ceilings and  
using a rear projection or large tube television this should be very  
easy.  
TV  
Using the following recommendations will insure your installation  
achieves maximum performance from the speakers.  
Left Center Right Speaker Placement  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLING THE SPEAKERS  
Step 1  
Remove the paint plug from the  
speaker. Attach the wire from your  
amplifier to the terminals on the back of  
the speaker. Double check the polarity  
of the speaker wires, amplifier + to  
speaker + and amplifier - to speaker -.  
Proper polarity is critical in home theater  
installations.  
PAINTING THE SPEAKERS AND GRILLES  
Speakers and grilles can be painted before installation, which will  
eliminate the "paint scar" if the speaker needs to be removed for  
service. Speakers may also be painted after installation, but before the  
grilles are attached. All speakers come from the factory fitted with a  
plastic "paint plug." Use the paint plug to protect the drivers while the  
flange is being painted with the ceiling.  
Step 2  
To install the Ellipse LCR, insert one side  
of the Flexbar clamps through the hole  
in the drywall. Once the feet are  
through the hole, insert the other side  
of the Flexbars into the cutout.  
Sonance suggests always painting the grilles separate from the  
speaker. The grilles may be lightly sprayed with thin paint (5 parts  
thinning agent to 1 part paint), but be careful not to plug the holes.  
Too much paint will adversely affect the sound of the speaker.  
Once the grilles and flange are painted and dry, remove the paint plug  
from the flange and install the grilles.  
Note: The maximum clamp thickness is  
1-1/4" (32mm)  
ADJUSTING YOUR SPEAKERS  
The Sonic Eye  
The unique sealed pivoting enclosure can direct sound toward or away  
from the listening area. To pivot the Sonic Eye, apply light pressure to  
the tweeter ring and the outside edge of the midrange. Do not apply  
pressure to the midrange cone or the tweeter dome. If you have any  
questions about how the Sonic Eye should be adjusted, consult your  
authorized Sonance dealer.  
Step 3  
Tighten the four screws on the front of  
the baffle. The Flexbars will  
automatically begin clamping the  
speaker. When you notice resistance on  
the four screws, the speaker has been  
clamped successfully.  
Here are some suggestions:  
Orient the Sonic Eye toward the listening area if the speakers are  
widely separated and the music fails to blend into a central image  
when the system is operated in stereo.  
The flange is designed to flex and  
conform to any small imperfections in  
the wall surface. The screws should not  
be tightened so far that the flange bows  
out.  
When using the Ellipse LCR in a home theater, point the Sonic Eye on  
all three speakers towards the listening position for more accurate  
sound.  
Step 4  
After the four Flexbar screws are  
tightened the grille can be installed.  
Insert about half of the grille into the  
groove at the edge of the speaker.  
Gently fit the remaining half of the grill  
into the speaker by working your hands  
around the speaker fitting the grille into  
the groove as you go along.  
Note: The torque applied to the  
mounting screws can be adjusted for  
proper grille fit.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ellipse 1.0 LCR  
TECHNICAL ASSISTANCE AND SERVICE  
The Technical Assistance Department at Sonance is available at (800)  
582-0772 or (949) 492-7777 to answer any questions concerning the  
operation and installation of your speakers between the hours of 7:00  
AM and 5:00 PM Pacific time, Monday through Friday, except holidays.  
Speaker Design  
In-ceiling LCR infinite baffle  
Tweeter  
Midrange  
Woofer  
1/2" (13mm) Cloth dome, pivoting  
4" (102 mm) Polypropylene cone, pivoting  
6-1/2" (165 mm) Black glass composite cone with a  
rubber surround  
In the event your unit should need repair or service, you may return  
the unit to your authorized dealer or use the following guidelines:  
Frequency Response 50Hz – 20kHz ±3dB  
1. Be prepared to state the model number and / or serial number,  
date of purchase and dealer's name and address when calling.  
Impedance  
Power  
8 ohms nominal, 6 ohms minimum  
5 watts minimum; 125 watts maximum  
89dB 1W / 1m  
Sensitivity  
2. Contact Sonance directly at (800) 582-0772 or (949) 492-7777 or  
Grille  
Aluminum  
Speaker Dimensions 10-1/2" (267mm) x 15-1/2" (394mm) x 5-7/8" (149mm)  
3. If you are returning the product directly to Sonance, call us to  
obtain a return authorization number before shipping. YOU MUST  
HAVE PRIOR AUTHORIZATION TO RETURN YOUR UNIT.  
Cutout Dimensions  
9" (171mm) x 14" (356mm) elliptical  
Weight  
8.0 lbs (3.63 kg) each  
4. The original packaging must be used. If the original packaging is  
unavailable, replacements can be obtained from Sonance for a  
small fee.  
Ellipse 2.0 LCR  
Speaker Design  
In-ceiling LCR infinite baffle  
5. Ship the product via a package delivery service such as UPS or  
Federal Express. Please do not use the U.S. Postal service.  
Tweeter  
Midrange  
Woofer  
1" (25mm) Aluminum dome, pivoting  
4" (102 mm) Aluminum cone, pivoting  
6-1/2" (165 mm) Black aluminum cone with a rubber  
surround and extended pole piece  
6. Write the return authorization number on the outside of the box.  
7. Ship to:  
Attn: Quality Assurance Department  
Sonance  
Frequency Response 40Hz – 20kHz ±3dB  
Impedance  
Power  
6 ohms nominal, 4 ohms minimum  
5 watts minimum; 150 watts maximum  
90dB 1W / 1m  
212 Avenida Fabricante  
San Clemente, CA 92672-7531  
Sensitivity  
8. FREIGHT COLLECT SHIPMENTS WILL BE REFUSED !  
Grille  
Aluminum  
Speaker Dimensions 10-1/2" (267mm) x 15-1/2" (394mm) x 5-7/8" (149mm)  
Cutout Dimensions  
9" (171mm) x 14" (356mm) elliptical  
Limited Lifetime Warranty  
Sonance warrants to the original retail purchaser only that this Sonance product will be free  
from defects in materials and workmanship, provided the speaker was purchased from a  
Sonance Authorized Dealer after September 1, 2003. Purchases made before that date carry a  
limited 5 year warranty.  
Weight  
9.0 lbs (4.1 kg) each  
10 1/2" (267mm)  
Defective products must be shipped, together with proof of purchase, prepaid insured to the  
Sonance Authorized Dealer from whom they were purchased, or to the Sonance factory at the  
address listed on this installation instruction manual. Freight collect shipments will be refused.  
It is preferable to ship this product in the original shipping container to lessen the chance of  
transit damage. In any case, the risk or loss or damage in transit is to be borne by the  
purchaser. If, upon examination at the Factory or Sonance Authorized Dealer, it is determined  
that the unit was defective in materials or workmanship at any time during this warranty  
period, Sonance or the Sonance Authorized Dealer will, at its option, repair or replace this  
product at no additional charge, except as set forth below. If this model is no longer available  
and can not be repaired effectively, Sonance, at its sole option may replace the unit with a  
current model of equal or greater value. In some cases where a new model is substituted, a  
modification to the mounting surface may be required. If mounting surface modification is  
required, Sonance assumes no responsibility or liability for such modification. All replaced parts  
and product become the property of Sonance. Products replaced or repaired under this  
warranty will be returned to the original retail purchaser, within a reasonable time, freight  
prepaid.  
This Warranty does not include service or parts to repair damage caused by accident, disaster,  
misuse, abuse, negligence, inadequate packing or shipping procedures, commercial use,  
voltage inputs in excess of the rated maximum of the unit, or service, repair or modification of  
the product which has not been authorized or approved by Sonance. This Warranty also  
excludes normal cosmetic deterioration caused by environmental conditions. This Warranty will  
be void if the Serial Number on the product has been removed, tampered with or defaced.  
This Warranty is in lieu of all other expressed warranties. If the product is defective in  
materials or workmanship as warranted above, the purchaser's sole remedy shall be repair or  
replacement as provided above. In no event will Sonance be liable for any incidental or  
consequential damages arising out of the use or inability to use the product, even if Sonance  
or a Sonance. Authorized Dealer has been advised of the possibility of such damages, or for  
any claim by any other party.  
14" (356mm)  
Some states do not allow the exclusion or limitation of consequential damages, so the above  
limitation and exclusion may not apply. All implied warranties on the product are limited to the  
duration of this expressed Warranty. Some states do not allow limitation on the length of an  
implied warranty. If the original retail purchaser resides in such a state, this limitation does not  
apply.  
w
w
w
.
s
o
n
a
n
c
e
.
c
o
m
Sonance • 212 Avenida Fabricante • San Clemente, CA 92672-7531, USA • (800) 582-7777 or (949)492-7777 • FAX: (949) 361-5151 • Technical Support: (800) 582-0772  
©2007 Sonance. Sonance, Sonic Eye, Flexbar, and Sonafill are trademarks of Dana Innovations.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sennheiser Microphone MKH 8060 User Manual
Sharp CRT Television Cx68n5 User Manual
Soleus Air Fan LX 140 User Manual
Sony Carrying Case MPK P1 User Manual
Sony Headphones MDRXB500 User Manual
Sony Home Theater System D E356CK User Manual
Southbend Lathe sb1015f User Manual
Sterling Dehumidifier 8820029500 User Manual
Suunto Scuba Diving Equipment SS019015000 User Manual
T Mobile Saw TM1758 User Manual