18” Metal Stand Table Fan
Model No: FS1-45-44 / FSM-45
Bronze & Gold / Brushed Nickel
Operating Instructions
FS1-
© 2006 Soleus Air International
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
This fan has a grounded three
pronged plug intended to fit into a
three slot outlet. (A) An adapter is
available for connecting three
pronged plugs into two slot outlets.
(B) When doing so, the green ground-
ing tab extending from the adapter
must be fastened under the wall
plate’s mounting screw. The adapter
should not be used if a three-slot out-
let is available.
DO NOT DEFEAT THE SAFETY
PURPOSE OF THE GROUNDED
PLUG.
TECHNICAL SPECIFICATIONS
Voltage Rating
Power Consumption
Unit Size
120V, 60Hz
60W
20 in. (W) x 16 in. (D) x 47 in. (H)
16.5 lbs
Unit Weight
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT DIAGRAM
A) Front Grill
B) Fan Blade
C) Securing Screw
D) Mounting Nut
E) Back Grill
F) Carrying Handle
G) Motor Shaft
H) Speed Control Knob
I) Oscillation Knob
J) Motor Housing
K) Fan Head Neck
L) Pole
M) Adjustable Height
Knob
N) Fan Base
O) Black Weight
P) Washer
Q) Locking Lever
R) Adjustable Tilt Knob
S) Range of Motion
Screw
T) Range of Motion Hole
U) Securing Knob
V) Carriage Bolt
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTIONS
Estimated assembly time: Approximately 5 minutes
Tools required: Phillips screwdriver (not included)
Base Assembly:
1) Unscrew the locking lever from the bottom of the pole.
2) Turn the pole upside down and slide the opening in the center of the fan base over the pole. Place the
black weight onto the base followed by the washer.
3) Insert the threaded end of the locking lever into the hole of the washer and through the base into the
bottom of the stand. Turn the locking lever clockwise to secure and tighten the base to the pole.
4) Turn the base over and set it on the floor.
5) On the neck of the fan head, remove the securing knob, carriage bolt and adjustable tilt knob. Loosen
the range of motion screw.
6) Slide the fan head neck over the top of the pole so that the range of motion screw aligns with the range
of motion hole.
7) Insert the carriage bolt into the square slot on the fan head neck and push through the hole.
8) Tighten the range of motion screw. Screw on the securing knob and the adjustable tilt knob.
Fan Head Assembly:
1) Remove the black sleeve and mounting nut from the motor shaft.
2) Position the back grill over the motor shaft, fitting the holes in the back grill over the knobs that pro-
trude from the motor. Make sure the rear grill fits securely against the motor housing and the handle is
at the top.
3) Secure the back grill by screwing on the mounting nut. Turn clockwise and tighten firmly.
4) Loosen the securing screw on the fan blade. Slide the fan blade onto the mounting shaft with the shaft
sleeve facing the motor. Align securing screw with flat groove in the motor shaft and tighten with Phil-
lips screwdriver.
5) Remove the small securing bolt from the bottom of the front grill. Position front grill so logo is hori-
zontal and make sure the grill clips are open. Secure the top tab to the back grill. Fasten the grills to-
gether with securing bolt. Hold the front grill against the rear grill and snap the grill clips closed to
complete the assembly.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
1. Set the fan on a stable, level surface.
2. Confirm that the Speed Control Knob is set to “O” (off). Plug the cord into a standard 120V A/C outlet.
3. Adjust to the desired speed setting:
O: Off
I: Low Speed
II: Medium Speed
III: High Speed
4. The fan can operate in oscillation or stationary mode. Press the Oscillation Knob down to activate the
oscillating mode. To stop oscillation, pull knob up.
5. Unplug the fan when not in use.
Adjustment Instructions:
• To adjust the angle of the fan head, loosen the adjustable-tilt knob and move the fan head to the desired
angle. Firmly tighten the knob to secure into place.
• To adjust the height of the fan, turn the adjustable height knob counter-clockwise to loosen the stand.
Adjust the fan to the desired height, then firmly tighten to secure into place.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING & MAINTENANCE
1. Turn the fan off and unplug the unit.
2. Wipe the fan down with a damp cloth for most efficient operation.
3. Air dry the fan completely before use.
4. Never use abrasive cleaning agents or solvents. This may cause damage or deterioration to the surface of
the unit.
5. Do not immerse the fan in any form of liquid. Do not allow water to drip on or into the fan motor
housing.
Fan Blade Cleaning:
• Make certain the fan is unplugged. Unlock the metal clips on the front grill and remove the front grill. Use
a Phillips screwdriver to loosen the securing screw and remove the fan blade.
• The fan blade and grill may be cleaned with a damp cloth and mild detergent.
• Reassemble the fan after the parts have dried completely. To do so, replace the fan blade, tighten the secur-
ing screw, and secure the front grill. Do not plug the fan into an electrical outlet until it is fully reassem-
bled.
STORAGE
If the fan will not be used for a long period of time, store it in a cool, dry location when not in use. To
prevent dust and dirt build-up, use the original packaging to repack the unit.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
One Year Limited Warranty
Soleus International Inc. warrants the accompanying Soleus Air 18” Stand Fan to be free of defects in material and
workmanship for the applications specified in its operation instruction for a period of ONE (1) year from the date of
original retail purchase in the United States.
If the unit exhibits a defect in normal use, Soleus International Inc. will, at its option, either repair or replace it, free of
charge within a reasonable time after the unit is returned during the warranty period.
As a condition to any warranty service obligation, the consumer must present this Warranty Certificate along with a
copy of the original purchase invoice.
THIS WARRANTY DOES NOT COVER:
•
Damage, accidental or otherwise, to the unit while in the possession of a consumer not caused by a defect in
material or workmanship.
•
Damage caused by consumer misuse, tampering, or failure to follow the care and special handling provisions
in the instructions. This includes dents, accidental or otherwise, to the base and head of the unit.
•
•
Damage to the finish of the case, or other appearance parts caused by wear.
Damage caused by repairs or alterations of the unit by anyone other than those authorized by Soleus
International Inc.
•
Freight and Insurance cost for the warranty service.
ALL WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANT ABILITY ARE LIMITED TO
ONE-YEAR DURATION OF THIS EXPRESS LIMITED WARRANTY. SOLEUS INTERNATIONAL INC.
DISCLAIMS ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES AND IN NO EVENT
SHALL SOLEUS INTERNATIONAL INC’S LIABILITY EXCEED THE RETAIL VALUE OF THE UNIT FOR
BREACH OF ANY WRITTEN OR IMPLIED WARRANTY WITH RESPECT TO THIS UNIT.
This warranty covers only new products purchased from our authorized dealers or retailers. It does not cover used, sal-
vaged, or refurbished products.
As some states do not allow the limitation or exclusion of incidental or consequential damages, or do not allow
limitation on implied warranties, the above limitations and exclusions may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights that vary from state to state.
For Technical Support & Warranty Service
Please Call (888) 876-5387
Or Write To:
Soleus International Inc.
9451 Telstar Ave.
El Monte, CA 91731 USA
8
Download from Www.Somanuals.com. All Manuals Search And Download.
|