FLAT PANEL MICATHERMIC HEATER
FLAT PANEL
MICATHERMIC
HEATER
Micathermic is a new method of heating that utilizes technology from both convection
and reflective heat. The heater releases 80% reflective and 20% convection heat,
distributing heat consistently and more evenly throughout the room. The heater releases
healthy infrared heat, directly warming surrounding objects. As the surrounding objects
absorb heat, the air temperature rises.
USER MANUAL
Model # HGW-308
Nowadays, saving energy is very important. Our heater features an ECO function
specifically designed for this reason. When the room temperature reaches the desired
temperature, one-third of energy will be cut-off automatically.
Special Features
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
Safe and healthy
Heats instantly and silently
Economic energy saving function [ECO]
Adjustable thermostat
Power and temperature control light indicator
Anti-freeze setting
Overheat safety protection
Lightweight
Quiet
Non-flammable surface
No dehumidifying
Specifications
Voltage Rating
Power Consumption
Unit Size
115 V, 60Hz
1500W
8.5“(L)x 22.5”(H)x 24.75“(W)
11.5 lbs
Unit Weight
PLEASE SAVE THESE INSTRUCTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Operation
PLEASE READ ALL INSTRUCTIONS BEFORE OPERATING HEATER !
Required tools for use on floor:
phillips screwdriver
(not included)
1. Ensure that the Temperature
Control Knob is at “DOT”
position. [Fig 1]
Required tools for wall
mounting:
phillips screwdriver
(not included)
drill (not included)
hammer (not included)
Also, make sure the power
switch is at the off position.
[Fig 2]
A. On the floor
Insert the feet and bolts onto the
unit as shown in the diagram.
2. Plug the power cord into a
suitable electrical outlet.
[Rated not less than 115 volt]
B. On the wall
3. Turn the power switch to the
“ON” position, then adjust the
Temperature Control Knob
clockwise until the Red Light
Indicator turns on [Fig 2]. At this
moment, the Temperature
STEP 1
Using the mounting support as a
guide, mark the first screw hole
on the wall.
Control will start working.
STEP 2
Drill first hole.
Note: The Red Light Indicator
will turn off when the room
reaches the desired temperature.
After a while, as the room
temperature falls, the heater will
turn on again and release heat
until the room temperature rises
to the desired temperature.
Desired room temperature is
maintained automatically by this
procedure.
STEP 3
Insert first screw anchor into the
first hole.
STEP 4
Put mounting support on the wall
and tighten it lightly.
STEP 5
Mark second screw hole on the
wall [approximately 5 7/16 in.].
STEP 6
Drill second hole.
You can adjust the temperature
control knob to increase or
STEP 7
decrease the room temperature as
desired by turning in a clockwise
or counter-clockwise direction as
shown in the figure.
Insert second screw anchor into
the second hole.
STEP 8
Tighten both screws.
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safeguards
PLEASE READ ALL INSTRUCTIONS BEFORE OPERATING HEATER !
4. To obtain a desirable
temperature, there is an area
indicated on the Temperature
Control Knob known as the
“Comfortable Zone.” You can
adjust the knob to select a
temperature within this range.
¾
The heater is hot when in use. To avoid burns, do not let bare skin touch hot
surface. Use handles when moving this heater.
Keep combustible materials, such as drapery and other furnishings, at least 3
feet [0.9m] from the front of the heater and away from the sides and rear.
Extreme caution is necessary when any heater is used by or near children or
invalids, or when the heater is left operating or unattended.
Do not use outdoor. Never locate heater where it may fall into a bathtub or
other water container.
This heater has hot and arcing or sparking parts inside. Do not use in areas
where gasoline, paint or flammable liquids are used or stored.
Do not insert or allow foreign objects to enter any ventilation or exhaust
opening as this may cause an electric shock or fire, or damage the heater.
To prevent a possible fire, do not block air intakes or exhaust in any manner.
Do not operate this appliance on soft surfaces because the inlet openings can be
blocked.
Always unplug heater when not in use. To disconnect heater, turn controls to
off, then remove plug from outlet.
Avoid using an extension cord because the extension cord may overheat and
cause a risk of fire. However, if an extension cord must be used, the conductor
wire inside the cord must be No.14 AWG minimum size and rated not less than
1875 watts.
¾
¾
¾
¾
¾
5. Anti-Freeze Setting
This setting keeps the
temperature of the surrounding
area above freezing to prevent
pipes from breaking. To do this,
simply plug in the heater and
turn the Temperature Control
Knob to the “Snowflake”
position. The heater will
automatically turn on when the
ambient temperature drops
below 41°F.
¾
¾
6. Economic Energy Saving
Function (ECO)
When the room temperature
reaches a certain point, the ECO
Green Light will switch on,
indicating that one-third of the
power has been cut-off
¾
Do not run cord under carpet and do not cover cord with throw rugs, runners,
or the like. Place the cord away from traffic area and where it will not be
tripped over.
¾
¾
The heater must not be located immediately below an outlet.
Do not operate any heater with a damaged cord or plug, after the heater
malfunctions, or has been dropped or damaged in any manner. If the heater is
damaged, it must be serviced by the manufacturer or a similarly qualified
service agent in order to ensure safety.
automatically to save energy.
[ our 1500 Watt heater will work
on 1000 Watts]
¾
¾
Connect the heater to properly grounded outlets only.
Use this heater only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock, or injury to
persons.
Do not use this heater with a programmer, timer or any other device that
switches the heater on automatically, since a fire risk exists if the heater is
covered or positioned incorrectly.
7. Overheat Safety Protection
The heater comes equipped with
overheat safety protection, so it
can detect if it is overheating and
will automatically shut off.
When the unit temperature falls
again, power will be resumed.
To avoid overheating and
potential risk of fire, DO NOT
cover the heater.
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning
WARRANTY
¾
¾
¾
¾
¾
Before cleaning, turn off the heater, unplug the power cord and allow the
heater to cool.
Do not immerse power cord and plug or heater in water or other liquid or pour
water or other liquid over the heater.
Use a vacuum cleaner to remove dust and lint from the metal grille of the
heater.
Wipe the heater with a dry cloth to remove dust and a damp cloth [not wet] to
clean off stains.
Do not use detergents, abrasive cleaning powder or polish of any kind on the
body of the heater, as these can damage the finish.
One Year Limited Warranty
Soleus International Inc. warrants the accompanying Soleus Air HGW-308 to be free of defects in
material and workmanship for the applications specified in its operation instruction for a period of
ONE (1) year from the date of original retail purchase in the United States or Canada.
If the heater exhibits a defect in normal use, Soleus International Inc. will, at its option, either
repair or replace it, free of charge within a reasonable time after the heater is returned during the
warranty period.
As a condition to any warranty service obligation, the consumer must present this Warranty
Certificate along with a copy of the original purchase invoice.
Storage
THIS WARRANTY DOES NOT COVER:
¾
Store the heater in a cool dry location. Preferably, to prevent dust and dirt build
up, use the old packaging to repack the unit.
1) Damage, accidental or otherwise, to the heater while in the possession of a consumer not
caused by a defect in material or workmanship.
2) Damage caused by consumer misuse, tampering, or failure to follow the care and special
handling provisions in the instructions.
3) Damage to the finish of the case, or other appearance parts caused by wear.
4) Damage caused by repairs or alterations of the heater by anyone other than those authorized
by Soleus International Inc.
Troubleshooting
HEATER WILL NOT HEAT
5) Freight and Insurance cost for the warranty service.
1. Check if the heater is plugged in and turned on.
2. Check if the Temperature Control Knob is in the right position.
3. Check if any objects are covering the unit.
ALL WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANT ABILITY
ARE LIMITED TO ONE-YEAR DURATION OF THIS EXPRESS LIMITED WARRANTY.
SOLEUS INTERNATIONAL INC. DISCLAIMS ANY LIABILITY FOR CONSEQUENTIAL
OR INCIDENTAL DAMAGES AND IN NO EVENT SHALL SOLEUS INTERNATIONAL
INC’S LIABILITY EXCEED THE RETAIL VALUE OF THE HEATER FOR BREACH OF
ANY WRITTEN OR IMPLIED WARRANTY WITH RESPECT TO THIS HEATER.
HEATER WILL NOT TURN ON
1. Check if the power cord is plugged into an electrical outlet.
2. Check if electricity or the main fuse is working.
3. Make sure the power switch is at [ON] position.
4. Check if the heater is on the Thermostat Control condition [ensure the Light
Indicator is on].
As some states do not allow the limitation or exclusion of incidental or consequential damages, or
do not allow limitation on implied warranties, the above limitations and exclusions may not apply
to you. This warranty gives you specific legal rights, and you may also have other rights that vary
from state to state.
For Warranty, Technical Support, Customer Service, Missing or Defective Parts
Please Call (888) 876-5387
Or Write To:
Soleus International Inc.
9451 Telstar Ave.
El Monte, CA 91731 USA
Download from Www.Somanuals.com. All Manuals Search And Download.
|