SET-UP INSTRUCTIONS & PRE-OPERATION CHECKLIST for
SNAPPER INTERMEDIATE FRAME SNOW THROWERS
INTRODUCTION: The SNAPPER Intermediate Frame Snow Throwers are shipped almost fully assembled and
require minimal set-up. Setting up the machine will require the handles to be unfolded and secured, and the
attachment of the chute crank rod. Some models may also require the installation of an electric start kit to the
engine. Complete each of the following steps carefully. Review and complete each item as instructed on the
Pre-Operation checklist. The Snapper Product Registration card must be filled out and sent to Customer
Service department at Snapper when completed.
STEP 1: HANDLES: Cut both wire ties that secure the
control cables to the handles. Be very careful and DO
NOT cut the control cables. See Figure 1.
STEP 3: HANDLES: Cut both wire ties that secure the
control levers to the handles. Cut the wire tie that
secures the chute crank to the handle. See Figure 3.
CUT WIRE TIE
THAT SECURES
CHUTE CRANK
CONTROL
LEVER
LOOSEN NUT
REMOVE
CARDBOARD
CHUTE
CRANK
CUT CABLE TIES
ON BOTH
HANDLES
CUT WIRE TIES
THAT SECURE THE
CONTROL LEVERS
TO THE HANDLES
DO NOT CUT
CONTROL CABLE
CONTROL
LEVER
FIGURE 1
FIGURE 3
STEP 2: HANDLES: Loosen handle nuts and rotate
handles up to the operating position. Remove shipping
cardboard from in between handles. See Figure 1.
Insert bolts through both upper & lower handles and
secure with nuts. Make sure the square necks of the
bolts are recessed into the square holes of upper
handles. Tighten nuts securely. See Figure 2.
STEP 4: CABLES: Make sure that the “Z” bend ends
of control cables are secured in the holes on the control
levers. Make sure cables are not kinked and have
freedom of movement when levers are engaged or
disengaged. See Figure 4.
CONTROL
LEVER
CHECK “Z” BEND END OF CABLE
IS SECURELY INSERTED INTO
HOLE ON CONTROL LEVER
SECURE UPPER
HANDLES WITH
FIGURE 4
BOLTS AND NUTS
TIGHTEN SECURELY
FIGURE 2
INSTRUCTIONS No. 7-4331 (Rev. 1, 4/08/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 8: ADJUSTMENT: Adjust cable lengths so that
each spring stretches 3/8” when the clutch lever is
depressed. When released, both clutch cables should
be slack. See Figure 8.
SPRING SHOULD
STRETCH 3/8”
WHEN HANDLE IS
DEPRESSED
CONNECTOR
JAM
NUT
TO ADJUST, LOOSEN JAM NUT
AND TURN CONNECTOR TO
SHORTEN OR LENGTHEN
CABLE AS NEEDED TO ATTAIN
THE 3/8” EXTENSION. TIGHTEN
JAM NUT AFTER ADJUSTING.
FIGURE 8
STEP 9: LUBRICATION: Remove check plug to
check grease level in auger gear case. If grease is not
visible from check plug hole, pump BENELENE 900
grease, SNAPPER Part No. 2-9577, into fill plug on
case until grease is visible. Reinstall check plug. See
Figure 9.
GEAR CASE
GREASE FITTING
CHECK PLUG
FIGURE 9
STEP 10: CHECKLIST: Complete all items on the Pre-
Operation Checklist as instructed.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PRE-OPERATION CHECKLIST for
SNAPPER INTERMEDIATE FRAME SNOW THROWERS
Snapper has completed initial adjustments and performed operational tests prior to shipping the machine. Due
to the possible effects of shipping, handling and storage, Snapper intends for all of the following items to be
verified and necessary final adjustments made at time of setup. It remains good practice and is strongly
recommended that all the items also be checked prior to placing the machine into service. It is very important
that setup is verified and all operational tests completed and results are acceptable. After completing this form,
sign and retain for future reference.
LUBRICATION
_____ ENGINE OIL added to bring level up to full mark on 4-cycle engines (Refer to Engine Manual).
_____ GEAR CASE grease level checked, add Benalene 900 grease (Snapper Part No. 2-9577) if needed.
OPERATIONAL TEST
_____ AUGER DRIVE CONTROL checked for proper engagement and disengagement to insure auger stops within 5
seconds after auger clutch control is released.
_____ WHEEL DRIVE CONTROL checked for proper engagement and disengagement of wheel drive.
_____ ENGINE started, engine speed control settings checked and adjusted as needed.
_____ IGNITION SWITCH checked to insure engine stops when turned to OFF position.
_____ ENGINE ELECTRIC STARTER checked for proper operation.
_____ FUEL SYSTEM checked for leaks around tank and connections.
______DISCHARGE CHUTE CRANK checked for proper operation and free rotation.
______AUGER and WHEEL DRIVE CONTROL CABLES checked and adjusted per instructions in the Operator’s Manual.
_____ GROUND SPEED CONTROL checked and adjusted per instructions in the Operator’s Manual.
_____ CHOKE CONTROL checked for proper operation during start up.
_____ TIRE PRESSURE checked. 15 to 20 PSI if chains are to be installed or 12 PSI if chains are not being used.
CONSUMER INFORMATION
Purchase Date __________________ Model_______________________ Serial No. _______________________
Retailers Name ___________________________________ ______________________________________________
Address _____________________________________ City ____________________ State _______ Zip ______
MACHINE WILL BE USED COMMERCIALLY? _____ YES _____ NO
Purchaser’s Name ________________________________ Signature ____________________________________
Address ____________________________________ City _____________________ State _______ Zip _______
IMPORTANT: This form is to be retained for future reference regarding Warranty, proof of purchase, traceability
for product recall or service, etc. Complete the Snapper Product Registration Card and Mail to Customer
Service Department at SNAPPER, P.O. Box 1379, McDonough, Georgia, 30253.
INSTRUCTION No. 7-4331 (Rev. 1, 4/08/02)
Printed in U.S.A.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
|