ATTACHMENT
OPERATOR’S
MANUAL
42” Single-Stage Snowthrower
42” Snowthrower Attachment
Mfg. No.
Description
1694920
42” Single-Stage Snowthrower
1733943
Revision 01
Rev. Date 9/2006
TP 100-4388-01-AT-SMAN
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Maintenance
Recommended Accessories ..............................1
Schedule for Normal Care...............................9
General Lubrication .........................................9
Safety Rules & Information
Training............................................................2
Preparation......................................................2
Operation.........................................................2
Children ...........................................................3
Clearing a Clogged Discharge Chute..............3
Service, Maintenance and Storage .................3
Emissions ........................................................3
Decals..............................................................4
Required Accessories...................................5
Recommended Accessories.........................5
Clean-Out Warning and Procedure..............5
Troubleshooting, Adjustments & Service
Troubleshooting Chart ...................................10
Skid Shoe Adjustment ...................................11
Electric Chute Rotator Gear .........................11
Lift Adjustment...............................................12
Belt Tension Adjustment................................12
Belt Replacement ..........................................13
Initial Setup & Assembly
Snowthrower Components ............................14
Chute Assembly ............................................15
Install Hitch onto Tractor................................16
Attaching Blower to Tractor............................17
Attaching Lift Arm Assembly to Tractor..........18
Attaching Chute Motor Wiring Harness.........19
Install Reflectors............................................19
Features & Controls
Control Functions ............................................6
General Operating Instructions
Checks Before Starting....................................7
Engine & Ground Speed Selection..................7
Stopping & Starting .........................................7
Transporting.....................................................7
Snow Removal Suggestions............................8
Daily Storage...................................................8
Off-Season Storage.........................................8
Removal
Snow Thrower Removal ................................20
NOTE: In these instructions, “left” and “right” are
referred to as seen from the operating position.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Rules
& Information
This machine is capable to amputating hands and feet and throwing objects. Read these safety rules and
follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury
or death to you, or bystanders, or damage to property or equipment. The triangle
important cautions or warnings which must be followed.
in text signifies
TRAINING
OPERATION
1. Read, understand, and follow all instructions on the
machine and in the manuals before operating this
unit. Be thoroughly familiar with the controls and the
proper use of the equipment. Know how to stop the
unit and disengage the controls quickly.
1. Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
2. Exercise extreme caution when operating on or
crossing gravel drives, walks, or roads. Stay alert for
hidden hazards or traffic. Do not carry Passengers.
3. After striking a foreign object, stop the engine (motor),
remove the wire from the spark plug, disconnect the
cord on electric motors, thoroughly inspect the
snowthrower for any damage, and repair the damage
before restarting and operating the snowthrower.
4. If the unit should start to vibrate abnormally, stop the
engine (motor) and check immediately for the cause.
Vibration is generally a warning of trouble.
5. Stop the engine (motor) whenever you leave the
operating position, before unclogging the
2. Never allow children to operate the equipment.
Never allow adults to operate the equipment without
proper instruction.
3. Keep the area of operation clear of all persons, partic-
ularly small children and pets.
PREPARATION
1. Thoroughly inspect the area where the equipment is
to be used and remove all doormats, sleds, boards,
wires, and other foreign objects.
collector/impeller housing or discharge guide, and
when making any repairs, adjustments, or inspec-
tions.
2. Disengage all clutches and shift into neutral before
starting engine (motor).
3. Do not operate the equipment without wearing ade-
quate winter outer garments. Avoid loose fitting cloth-
ing that can get caught in moving parts. Wear
footwear that will improve footing on slippery sur-
faces.
6. When leaving the machine unattended, disengage
the power take-off (PTO), lower the attachment, set
the parking brake, stop the engine, and remove the
key.
7. When cleaning, repairing, or inspecting make certain
the collector/impeller and all moving parts have
stopped. Disconnect the spark plug wire and keep
the wire away from the plug to prevent accidental
starting. Do not run the engine indoors except for
starting the engine or for transporting the snowthrow-
er in or out of the building. Open the outside doors;
exhaust fumes are dangerous.
8. Exercise extreme caution when operating on slopes.
Do not attempt to clear steep slopes.
9. Never operate the snowthrower without proper
guards plates, or other safety protective devices in
place and working.
10. Never direct the discharge toward people or areas
where property damage can occur. Keep children
and others away.
11. Do not overload the machine capacity by attempting
to clear snow at too fast a rate.
12. Never operate the machine at high transport speeds
on slippery surfaces. Look behind and use care
when operating in reverse.
13. Disengage power to the collector/impeller when
snowthrower is transported or not in use.
14. Use only attachments and accessories approved by
the manufacturer of the snowthrower (such as wheel
weights, counterweights, or cabs).
15. Never operate the snowthrower without good visibility
or light. Always be sure of your footing, and keep a
firm hold on the handles. Walk, never run.
16. Never touch a hot engine or muffler.
17. Never operate the snowthrower near glass enclo-
sures, automobiles, window wells, drop-offs, and the
like without proper adjustment of the discharge angle.
18. Never direct discharge at bystanders or allow anyone
in front of the unit.
4. Handle fuel with care; it is highly flammable.
(a) Use an approved fuel container.
(b) Never add fuel to a running engine or hot engine.
(c) Fill fuel tank outdoors with extreme care. Never fill
fuel tank indoors. Replace fuel cap securely and
wipe up spilled fuel.
(d) Never fill containers inside a vehicle or on a truck
or trailer bed with a plastic liner. Always place con-
tainers on the ground, away from your vehicle, before
filling.
(e) When practical, remove gas-powered equipment
from the truck or trailer and refuel it on the ground. If
this is not possible, then refuel such on a trailer with a
portable container, rather than from a gasoline dis-
penser nozzle.
(f) Keep nozzle in contact with the rim of the fuel tank
or container opening at all times, until refueling is
complete. Do not use a nozzle lock-open device.
(g) Replace gasoline cap securely and wipe up spilled
fuel.
(h) If fuel is spilled on clothing, change clothing imme-
diately.
5. Adjust the collector housing height to clear gravel or
crushed rock surfaces.
6. Never attempt to make any adjustments while the
engine (motor) is running (except when specifically
recommended by the manufacturer).
7. Let engine (motor) and machine adjust to outdoor
temperatures before starting to clear snow.
8. Always wear safety glasses or eye shields during
operation or while performing an adjustment or repair
to protect eye from foreign objects that may be
thrown from the machine.
TP-600-4159-01-UV-SMAN
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Decals
19. Never leave a running unit unattended. Always disen-
gage the auger and traction controls, stop engine,
and remove keys.
7. Always observe safe refueling and fuel handling prac-
tices when refueling the unit after transportation or
storage.
8. Always follow the engine manual instructions for stor-
age preparations before storing the unit for both short
and long term periods.
9. Always follow the engine manual instructions for
proper start-up procedures when returning the unit to
service.
10. Maintain or replace safety and instruction labels as
necessary.
11. Keep nuts and bolts tight and keep equipment in
good condition.
12. Never tamper with safety devices. Check their proper
operation regularly and make necessary repairs if
they are not functioning properly.
20. Do not operate the unit while under the influence of
alcohol or drugs.
21. Keep in mind the operator is responsible for acci-
dents occurring to other people or property.
22. Data indicates that operators, age 60 years and
above, are involved in a large percentage of power
equipment-related injuries. These operators should
evaluate their ability to operate the unit safely enough
to protect themselves and others from injury.
23. DO NOT wear long scarves or loose clothing that
could become entangled in moving parts.
24. Snow can hide obstacles. Make sure to remove all
obstacles from the area to be cleared.
13. Components are subject to wear, damage, and dete-
rioration. Frequently check components and replace
with manufacturer’s recommended parts, when nec-
essary.
CHILDREN
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the
unit and the operating activity. Never assume that children
will remain where you last saw them.
14. Check control operation frequently. Adjust and ser-
vice as required.
15. Use only factory authorized replacement parts when
making repairs.
16. Always comply with factory specifications on all set-
tings and adjustments.
17. Only authorized service locations should be utilized
for major service and repair requirements.
18. Never attempt to make major repairs on this unit
unless you have been properly trained. Improper ser-
vice procedures can result in hazardous operation,
equipment damage and voiding of manufacturer’s
warranty.
19. Check shear bolts and other bolts at frequent inter-
vals for proper tightness to be sure the equipment is
in safe working condition.
1. Keep children out of the area and under the watchful
care of another responsible adult.
2. Be alert and turn unit off if children enter the area.
3. Never allow children to operate the unit.
4. Use extra care when approaching blind corners,
shrubs, trees, or other objects that may obscure
vision.
CLEARING A CLOGGED DISCHARGE
CHUTE
Hand contact with the rotating impeller inside the dis-
charge chute is the most common cause of injury associ-
ated with snowthrowers. Never use your hand to clean
out the discharge chute.
EMISSIONS
1. Engine exhaust from this product contains chemicals
known, in certain quantities, to cause cancer, birth
defects, or other reproductive harm.
2. If available, look for the relevant Emissions Durability
Period and Air Index information on the engine emis-
sions label.
To clear the chute:
1. SHUT OFF THE ENGINE.
2. Wait 10 seconds to be sure the impeller blades have
stopped rotating.
3. Always use a clean out tool, not your hands.
SERVICE, MAINTENANCE, AND STORAGE
1. Check shear bolts and other bolts at frequent inter-
vals for proper tightness to be sure the equipment is
in safe working condition.
2. Never store the machine with fuel in the fuel tank
inside a building where ignition sources are present
such as hot water and spacer heaters, or clothes dry-
ers. Allow the engine to cool before storing in any
enclosure.
3. Always refer to the operator’s manual for important
details if the snowthrower is to be stored for an
extended period.
4. Maintain or replace safety and instruction labels as
necessary.
5. Run the machine a few minutes after throwing snow
to prevent freeze-up of the collector/impeller.
6. If fuel is spilled, do not attempt to start the engine but
move the machine away from the area of spillage and
avoid creating any source of ignition until fuel vapors
have dissipated.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Decals
All DANGER, WARNING, CAUTION and instructional
messages on your unit should be carefully read and
obeyed. Personal bodily injury can result when these
instructions are not followed. The information is for your
safety and it is important! The safety decals below are on
your unit.
SAFETY DECALS
This unit has been designed and manufactured to pro-
vide you with the safety and reliability you would expect
from an industry leader in outdoor power equipment
manufacturing.
Although reading this manual and the safety instructions
it contains will provide you with the necessary basic
knowledge to operate this equipment safely and effec-
tively, we have placed several safety labels on the unit to
remind you of this important information while you are
operating your unit.
If any of these decals are lost or damaged, replace them
at once. See your local dealer for replacements.
These labels are easily applied and will act as a constant
visual reminder to you, and others who may use the
equipment, to follow the safety instructions necessary for
safe, effective operation.
Part No. 1716532
Auger Danger Decal
Part No. 1722674
Discharge Chute Danger Decal
Part No. 1716531
Main Operation Warning Decal
WHEN OPERATING
WITH SNOWTHROWER,
REAR WHEEL WEIGHTS
ARE REQUIRED.
CAUTION
1716540
Part No. 1716540
Rear Wheel Weights Required
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Required Accessories
Required Accessories
It is required that tire chains and two rear wheel weights or Quick Tach Weights are used.
Never operate on slopes greater than 17.6% (10°).
Recommended Accessories
A rear-mounted weight box can also be added for additional traction. The maximum weight added to the tractor
should not exceed 35 lbs. per wheel, plus 100 additional pounds in the rear weight box.
For operation on slopes greater than 15% (8.5°), Quick Tach Weights, tire chains, and wheel weights are recom-
mended. Never operate on slopes greater than 17.6% (10°).
Required Accessories
A Lift Lever Kit is required for some of the models covered by this manual, and must be installed as part of hitch
installation.
DANGER
Do not clean out discharge chute with hands.
Contact with moving parts inside chute will
cause serious injury. Use a clean out tool. Use
the following procedure to remove objects or
clear the chute:
1. Stop the engine. Remove the key
2. Wait 10 seconds to be sure the auger/impeller
blades have stopped rotating.
3. Always use a clean-out tool. DO NOT use your
hands.
TRACTOR CONTROLS
Before you begin operating the tractor and attachment,
make certain you have:
• Read and understood the instructions in the
tractor Operator’s Manual.
• Become thoroughly familiar with all of the trac-
tor controls and their operation, including how
to safely and properly start and stop the unit.
• Practice driving in an open area, without the
attachment, to become accustomed to the unit.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Features &
Controls
D
CONTROL FUNCTIONS
The information below briefly describes the
function of individual controls. Operating the
tractor and attachment requires the combined
use of these controls and additional controls
whose operation is described in the tractor
Operator’s Manual.
B
A
Please take a moment
and familiarize yourself
with the name, location,
and function of these
controls so that you will
better understand the
safety and operating
instructions provided in
this manual.
E
Figure 1. Control Locations
A. Spout Rotator Switch
B. PTO Switch
C. Manual Lift
D. Deflector Lock Knob
E. Throttle Control
E
A. Electric Spout Rotator Switch
Controls the electric spout rotator.
B. PTO Switch
Engages and disengages the PTO to start and stop the
snowthrower.
C. Manual Attachment Lift Lever
The attachment lift lever raises and lowers the attach-
ment. To RAISE an attachment, depress the release
button on top of the lever and pull back. To LOWER an
attachment, depress the release button and move the
lever forward. When lowering the attachment, be sure to
push the lever fully forward into the locked position.
TRACTOR CONTROLS
Before you begin operating the tractor and attachment,
make certain you have:
D. Deflector Lock Knob
The snowthrower discharge deflector angle can be
changed by loosening the lock knob, changing the
deflector angle and tightening the lock knob.
• Read and understood the instructions in the
tractor Operator’s Manual.
• Become thoroughly familiar with all of the trac-
tor controls and their operation, including how
to safely and properly start and stop the unit.
E. Throttle Control
Always operate at FULL throttle.
• Practice driving in an open area, without the
attachment, to become accustomed to the unit.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
General Operating
Instructions
WARNING
WARNING
Perform the Safety System Interlock test found in
your tractor Operator’s Manual. If tractor does not
pass the test, do not operate the tractor. See your
authorized dealer. Under no circumstances
If auger does not start and stop when
engaging/disengaging electric clutch, see your
authorized dealer. Under no circumstances
should you attempt to defeat the safety system.
should you attempt to defeat the safety system.
Use caution when clearing a snow covered area.
Snow can cover objects such as curbs, drop-offs,
and other obstacles. Be familiar with the area you
are clearing.
Checks Before Starting
IMPORTANT NOTE: Refer to Tractor Operator’s Manual
for important information concerning safely storing your
tractor.
To prevent an explosion or fire, never store the
tractor with fuel in the tank inside a building
where an ignition source is present.
1. Refer to the Maintenance & Adjustments sections of
this manual and perform any needed service. Also,
refer to the tractor Operator’s Manual and perform
any required service.
IMPORTANT NOTE
Always raise the snowthrower before turning or
backing up to prevent damage to the unit.
2. Remove any objects from the work area which might
be caught in, or thrown by, the auger.
3. Before starting the engine, clear the auger of any ice
particles which may cause damage to auger.
DANGER
OPERATING ON SLOPES CAN BE DANGEROUS
4. Adjust the deflector and skid shoes to desired height.
See Skid Shoe Adjustment and Deflector Adjustment.
5. Make sure all hardware is present and secure.
Engine & Ground Speed Selection
Always run the engine at full throttle.
Never operate on slopes greater than 17.6% (10°)
which is a rise of 3-1/2 feet (106cm) vertically in
10 feet (607cm) horizontally.
Operate the unit at a slow ground speed when
driving onto slope. Avoid using brakes to control
ground speed.
Normally, a slow ground speed is best for throwing snow.
The deeper or heavier the snow, the slower the recom-
mended ground speed.
When operating on slopes that are greater than
15 % (8.5°) but less than 17.6%, use additional
wheel weights or counterweights.
Starting & Stopping
1. Start the tractor engine. Set engine throttle FULL.
2. Lower the snowthrower.
In addition to counterweights, use extra caution
when operating on slopes. Drive UP and DOWN
the slope, never across the face, use caution
when changing directions and DO NOT START
OR STOP ON SLOPE.
3. Engage the electric clutch switch. Snowthrower auger
should rotate. Disengage the electric clutch switch.
Snowthrower auger should stop.
4. Adjust the throttle to full speed. Select the proper
ground speed.
For additional traction, tire chains and a weight
box can be added. Maximum weight added to
tractor should not exceed 50 lbs. per wheel and
100 additional lbs. in weight box.
5. To stop tractor movement, depress the clutch/brake
pedal. To stop the snowthrower, disengage the elec-
tric clutch. Before leaving the seat, disengage the
electric clutch, set the parking brake, stop the engine,
remove the key, and wait for all moving parts to stop.
Transporting
1. Disengage the electric clutch and then raise the
snowthrower.
2. Adjust ground speed according to surface conditions.
3. Select a low ground speed when transporting on a
slippery surface.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
General Operating Instructions
Snow Removal Suggestions
• Determine the best snow removal pattern before
beginning.
• Wind direction is an important factor to consider.
Rotate the spout to discharge snow downwind.
• Plan the pattern so that you avoid throwing snow on
cleared areas and on yourself as you are operating.
• When land contour permits, it is best to travel in the
longest direction to minimize turning.
• In very deep or heavy snow, it may be necessary to
make the first pass with snowthrower partially raised,
backing up every few feet and lowering the
snowthrower to clear the snow left on the surface.
Also, it may be necessary to slice off less than the full
width of the auger or reduce ground speed.
• If snow stops flowing freely from the spout, back
away until the snowthrower clears itself.
DANGER
If the auger stalls or the chute plugs, DISENGAGE
THE ELECTRIC CLUTCH, STOP THE ENGINE AND
REMOVE THE KEY. SET THE PARKING BRAKE.
WAIT FOR MOVING PARTS TO STOP. Remove
the foreign object or clear the spout with a piece
of wood before restarting the engine. Never place
hands into auger housing or spout to clear
jammed object. Auger may rotate when object is
removed.
Daily Storage
1. Run the snowthrower a few minutes after blowing
snow to prevent freeze-up of auger.
2. Allow tractor engine to cool before storing in any
enclosure.
Off-Season Storage
1. Remove snowthrower from the tractor.
2. Use water pressure or a brush to thoroughly clean
the housing.
3. Paint, or lightly coat with oil, any area where paint
has been worn or chipped away.
4. Lubricate the snowthrower.
5. Store the snowthrower and hitch in a dry place.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
WARNING
To avoid serious injury, perform maintenance on
the unit only when the engine is stopped and all
moving parts have stopped. Always remove the
ignition key before beginning maintenance or
adjustments to prevent accidental starting of the
engine.
Schedule For Normal Care
Care Required
Schedule
Clean snow and ice from
snowthrower.
After each use.
Lubricate snowthrower.
Every 10 hours or at
least once a year.
General Lubrication
Lubricate the snow thrower as shown in Figure 2. Where
an oil can is shown use 30 weight oil. Where a grease
gun is shown, use lithium grease. Lubricate the following
areas:
• Oil the chute deflector.
• Grease the chute ring gear.
• Grease the snow thrower-hitch pivot points.
• Grease the auger shaft grease fittings.
Figure 2. Lubrication Points
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting,
Adjustments, & Service
TROUBLESHOOTING
While normal care and regular maintenance will extend
the life of your equipment, prolonged or constant use
may eventually require that service be performed to
allow it to continue operating properly.
WARNING
To avoid serious injury, perform maintenance on
the tractor or snow thrower only when the engine
is stopped and the parking brake engaged.
Always remove the ignition key, disconnect the
spark plug wire and fasten it away from the plug
before beginning the maintenance, to prevent
accidental starting of the engine.
The troubleshooting guide below lists the most common
problems, their causes and remedies. See the informa-
tion on the following pages for instructions on how to per-
form most of these minor adjustments and service
repairs yourself. If you prefer, all of these procedures can
be performed for you by your local authorized dealer.
PROBLEM
CAUSE/SOLUTION
1 Snow thrower auger does not rotate.
A. Electric clutch not engaged. Engage electric clutch.
B. Foreign material is blocking auger. STOP engine. Remove key.
Unplug auger with piece of wood. Read WARNING on page 5.
C. Drive chain broken. Replace parts as required.
2 Auger does not stop when electric clutch
is disengaged.
A. Electric clutch brake not operating properly. See your dealer.
3 Auger rotates, but snow is
not thrown far enough.
A. Engine RPM too slow. Set throttle to FULL.
B. Ground speed too fast. Use slow ground speed.
C. Snow thrower discharge chute clogged. STOP engine. Remove
key. Unplug discharge chute using the chute cleaning tool or a
piece of wood. Read WARNING on page 5.
4 Scraper bar does not clean
down to hard surface.
A. Skid shoes not properly adjusted. Adjust skid shoes.
B. Lift height out of adjustment. See ADJUSTMENTS section.
C. No down pressure. See Hitch Installation Instructions.
5 Snow thrower picks up and
throws stones on gravel drive.
A. Skid shoes not properly adjusted for ground surface.
Adjust skid shoes.
B. Too much downward pressure on snow thrower. Raise snow
thrower slightly.
6 Tractor does not have sufficient traction.
7 Tractor not stable on sloping surfaces.
A. Tractor too light at rear wheels.
Use Quick Tach weights, wheel weights, and tire chains.
A. Ground speed too fast. Reduce speed.
B. Tractor not properly weighted.
See Recommended Accessories, page 1.
C. Slope grade too steep. See Safety Section.
Use Quick Tach weights, wheel weights, and tire chains.
8 Chute does not rotate.
A. Rotator gears out of adjustment.
B. Wire harness disconnected.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting, Adjustments, & Service
Skid Shoe Adjustment
On smooth surfaces such as concrete or asphalt, the
scraper bar should scrape the surface. On surfaces such
as gravel, the scraper bar should be set high enough so
that it will not pick up debris.
Loosen Nuts
to Adjust
1. Loosen the nuts securing the skid shoes (see
Figure 3).
2. Raise or lower the scraper bar to the desired height.
Use wood blocks to hold the snow thrower in posi-
tion.
3. Set the skid shoes so that they are in contact with the
ground and tighten the skid shoe nuts.
Figure 3. Adjusting Skid Shoes
Electric Chute Rotator Gear
1. Remove the cover and loosen the three screws (B,
Figure 4) securing the electric chute rotator motor.
2. Adjust the motor (C) so that the gear (A) meshes with
the discharge chute ring gear and tighten the adjust-
ment screws (B).
A
B
C
3. Reinstall the cover.
Figure 4. Chute Rotator Gear
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting, Adjustments, & Service
Lift Adjustment
In the fully raised position the attachment should be 4”-5”
off the ground.
LIFT HEIGHT ADJUSTMENT
1. Fully raise the attachment lift. The snow thrower
should be approximately 4”-5” off the ground. If not,
go to step 2.
2. Lower the snow thrower and adjust the front set collar
(A, Figure 5) to achieve the correct lift height.
Belt Tension Adjustment
Adjust belt tension if the tension lever does not adjust
belt tension properly.
A
1. Loosen bolt (A, Figure 6) on idler pulley (D), located
on the left side of the hitch assembly.
2. Move belt tension lever to the released position (C).
3. Move idler pulley (D) backwards or forwards to adjust
snow thrower drive belt tension.
Figure 5. Height Adjustment Collar
4. Move belt tension lever to the locked tension position
(B).
5. Test snow thrower and repeat adjustment as needed.
A
B
D
C
Figure 6. Belt Tension Adjustment
A. Idler Pulley Bolt
B. Belt Tension Lever – Locked Position
C. Belt Tension Lever – Tension Released Position
D. Idler Pulley
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting, Adjustments, & Service
Belt Replacement
E
1. Move tension release lever to the released position
(C, Figure 6).
2. Remove the belt from the snow thrower pulley
(D, Figure 7).
C
B
3. Remove the belt from the machine.
4. Install the new belt as shown in Figure 7.
5. Move the belt tension lever to the locked position
(B, Figure 6).
A
D
Figure 7. Belt Routing
A. V-Pulley
B. Idler Pulley
C. Electric Clutch Pulley (V-pulley)
D. Snow thrower Pulley (V-pulley)
E. Idler Pulley
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
& Assembly
1
4
3
5
6
17
2
6
15
16
7
10
8
9
14
11
12
Q
T
Y
QTY
13
4
4
Ref Qty Description
Ref Qty Description
1
2
3
4
5
6
7
8
9
1
2
1
1
1
1
1
1
1
UPPER WIRING HARNESS
REFLECTORS
FINAL WIRING HARNESS
CHUTE ROTATION SWITCH
HITCH SUPPORT SHAFT
HAIR PIN COTTER
HITCH ASSEMBLY
HITCH LATCH PIN
AXLE CLIP
10
11
12
13
14
15
16
17
18
2
1
1
1
1
4
1
1
1
MOUNTING PINS
QUICK CLIP
SPRING
TURN BUCKLE
BLOWER ASSEMBLY
QUICK CLIPS
LIFT ARM LINKAGE
LIFT ARM ASSEMBLY
CHUTE ASSEMBLY (not shown)
Figure 8. Initial Setup
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup & Assembly
CHUTE ASSEMBLY
E
1. Carefully unpack and organize Snow thrower parts.
D
2. Remove chute rotator drive cover (B, Figure 9) from
the snow thrower assembly by removing hex screw
(A) and tilting the gearbox cover to disengage tab on
opposite side of box.
B
3. Remove chute rotator gear from shaft (C).
Note location of notch (D) in chute ring gear. Align
the notch in the chute assembly with the guide tab at
the base of the discharge outlet.
C
4. Slide chute (E) into place and rotate chute 180
degrees to front.
A
Note: Chute opening should be facing front/center of
machine.
Figure 9. Chute Assembly
A. Chute Rotator Drive Cover Bolt
B. Chute Rotator Drive Cover
C. Chute Rotator Drive Assembly
D. Chute Assembly Notch
E. Chute Assembly
5. Replace chute rotator gear (A, Figure 10) onto shaft
and rotate to align chute ring gear and drive gear.
6. Loosen, but do not remove the 3 hex bolts (B) hold-
ing chute rotator drive assembly to the snow thrower.
7. Move chute rotator drive assembly (C) toward chute
until the chute ring gear meshes with the rotation
motor drive gear. Tighten the 3 hex bolts.
8. Replace chute gearbox cover over rotator (B, Figure
9)gear mechanism and secure with the hex bolt.
A
B
C
Figure 10. Chute Assembly
A. Chute Rotator Gear
B. Hex Bolts
C. Chute Rotator Drive Assembly
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup & Assembly
INSTALL HITCH ONTO TRACTOR
1. Remove mower deck.
2. Place hitch on floor in front of tractor, with the hitch
mounting arms towards the rear of the tractor.
NOTE: If this is a new installation, cut the plastic ties
holding the snow thrower drive belt for shipping, but do
not remove the belt.
3. On underside of tractor frame, insert hitch support
shaft (A, Figure 11) as shown and secure, with the hair
pin cotter pin (B) on inside of frame. IMPORTANT –
the hair pin cotter pin must be located along the inside
edge of the tractor frame.
4. Slide hitch (A, Figure 12) under tractor and lift to slide
hitch mounting arms (C) over hitch support shaft (B).
5. At front of the machine, locate and remove the hitch
latch pin (A, Figure 13) from the hitch assembly (B).
6. Turn the front wheels fully to the left.
C
B
A
Figure 12. Hitch Installation
A. Hitch Assembly
B. Hitch Support Shaft
C. Hitch Mounting Arms
C
A
D
A
B
Figure 11. Install Hitch Support Shaft
A. Hitch Support Shaft
B. Hair Pin Cotter
B
Figure 13. Hitch Latch Pin Installation
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup & Assembly
7. Lift the hitch (B) and from the left side of the tractor,
slide hitch latch pin (A) through the mounting hole in
hitch frame, along the tractor frame support fingers
(C) and through the final mounting hole in hitch frame.
Secure hitch latch pin (A) with the quick clip (D).
NOTE: Keep the handle portion of the hitch latch pin
towards the front of the tractor.
8. Hitch installation is now complete.
ATTACHING BLOWER TO TRACTOR
1. Position snow thrower assembly in front of tractor.
2. Remove both quick clips (E, Figure 14) and mounting
pins (D) from the snow thrower.
B
3. Align the hitch mounting arms (B) with the snow
thrower mounting tabs (C) and slide the snow thrower
into position.
4. Align mounting holes on snow thrower frame with the
mounting holes in the hitch.
5. Insert mounting pins (D) and secure with quick clips
(E).
A
6. Locate the belt tension lever (B, Figure 15) at the rear
of the hitch assembly and rotate it into the released
position (A).
Figure 15. Belt Tension Lever
A. Belt Tension Lever – Released Position
B. Belt Tension Lever – Tension Position
7. Install the drive belt onto the snow thrower drive pul-
ley (D, Figure 16) and then onto the tractor PTO (C).
See Belt Installation Diagram (Figure 16)
E
E
D
C
B
B
C
A
E
D
D
A
Figure 16. Belt Installation Diagram
A. V-Pulley
B. Idler Pulley
C. PTO Pulley
D. Snow Thrower Pulley
E. Idler Puller
Figure 14. Snow Thrower Installation
A. Snow Thrower Assembly
B. Hitch Mounting Arms
C. Snow Thrower Mounting Tabs
D. Mounting Pins
E. Quick Clips
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup & Assembly
8. Rotate the belt tension lever upwards into the locked
position (B, Figure 15), fully tensioning the snow
thrower drive belt.
NOTE: Do not connect the mower deck lift arm or cable
to the belt tension lever.
ATTACHING LIFT ARM ASSEMBLY TO
TRACTOR
1. On right side of tractor, remove the four (4) hex bolts
and nuts (B, Figure 17) from hitch assembly.
D
2. Attach lift arm assembly (A) to the tractor frame using
the four hex bolts (B) and nuts.
3. Install Lift Arm linkage (C) as shown and secure with
quick clips (D).
D
4. Adjust the lifting collar (E) to make sure that the snow
thrower is lifted clear of the ground for transportation.
5. Assemble lift assist parts; attach spring (B, Figure 18)
to turnbuckle (C) and axle clamp (A).
NOTE: Make sure to position the axle clamp (E) so that
it does not contact the axle rib (F) and fully seats on the
axle.
A
E
C
B
6. Fully raise the snow thrower off the ground.
Figure 17. Lift Arm and Linkage
A. Lift Arm Assembly
B. Mounting Bolts and Nuts
C. Lift Arm Linkage
D. Quick Clip
E. Lifting Collar
7. Attach open end of turnbuckle to eye-bolt (D) on
blower assembly and the spring (B) as shown.
8. Adjust spring tension by rotating the turnbuckle until
threads bottom out on both sides.
9. Remove the skid shoes from the snowthrower and
rotate them from the shipping position to the normal
use position. Adjust the skid shoes for proper snow
removal. See Troubleshootng, Adjustments and
Service for skid shoe adjustment procedures.
E
A
B
F
C
D
Figure 18. Lift Assist Spring Assembly
A. Axle Clamp
B. Spring
C. Turnbuckle
D. Eye-bolt
E. Axle Clamp
F. Axle Rib
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup & Assembly
ATTACHING CHUTE MOTOR
WIRING HARNESS
1. Wiring Harness is in four (4) parts.
a. Switch
A
b. Upper wiring harness with main power connector
c. Final wiring harness with a square connector on
each end.
2. Remove plug from tractor control panel at position
shown and install the chute rotation switch
(A, Figure 19).
B
3. Plug female receptacle (B, Figure 19) end of the
upper wiring harness onto switch.
C
4. Route the upper wiring harness (B, Figure 19) down
through the right side of the panel enclosure, locating
the square connector in front of the firewall, along the
tractor frame.
5. Locate the power leads (Red with yellow stripe and
black) in the tractor wiring harness at the base of
steering column. Connect the wiring harness power
leads (B, Figure 20), color to color, to the chute rota-
tion wiring harness spade connectors.
Figure 19. Upper Wiring Harness
A. Switch
B. Female Receptacle
C. Rotation Motor Power Leads
6. Connect the final wiring harness (B, Figure 20) to the
upper wiring harness (A) using the square connector
and then to the chute rotation motor connector (D).
Position the wiring heat cover underneath the tractors
muffler. Loosely secure the final wire harness (B) to
the lift arm linkage (C, Figure 23)
D
Install Reflectors
1. Install the two reflectors on the rear of the tractor seat
deck.
A
B
C
Figure 20. Wiring Harness Connections
A. Upper Wiring Harness
B. Final Wiring Harness.
C. Mounting Clip
D. Chute Rotation Motor Connection
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal
Snow Thrower Removal
CAUTION
Make sure to shut off the engine and locking the
tractor brakes or block the rear wheels before
beginning the snow thrower removal process.
B
1. Fully raise and support the snow thrower with wooden
blocks.
2. Loosen the turn buckle (C, Figure 21) and then
remove the lift assist spring, turn buckle and axle
clamp.
A
3. Lower the snow thrower to the ground.
4. Move the belt tension lever to the RELEASED
position (A, Figure 22).
Figure 22. Belt Tension Lever
A. Belt Tension Lever – Released Position
B. Belt Tension Lever – Tension Position
5. Remove the snow thrower drive belt from the snow
thrower pulley and PTO pulley.
6. Remove the two quick clips (D, Figure 23) securing
the lift arm linkage and remove the lift arm linkage
(C).
NOTE: The Lift Arm assembly (A) will remain in place on
the hitch assembly.
D
A
D
B
C
D
A
C
B
E
Figure 21. Adjusting Belt Tension
A. Axle Clamp
B. Spring
C. Turnbuckle
D. Eye-bolt
Figure 23. Lift Arm Linkage
A. Lift Arm Assembly
B. Mounting Bolts and Nuts
C. Lift Arm Linkage
D. Quick Clip
E. Lifting Collar
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal
7. Disconnect the final wiring harness (B, Figure 24).
8. Remove both quick clips (E, Figure 25) and snow
thrower mounting pins (D).
E
D
9. Move the snow thrower assembly (A, Figure 25) out
of the way.
10. Turn the front wheels fully to the left. Remove the
latch pin quick clip (D, Figure 26) and slide the latch
pin (A) to the left.
B
C
E
CAUTION
Make sure to support the front of the hitch
assembly as it will be loose when the latch pin
has been removed.
D
A
Figure 25. Snow Thrower Installation
A. Snow Thrower Assembly
B. Hitch Mounting Arms
C. Snow Thrower Mounting Tabs
D. Mounting Pins
E. Quick Clips
D
C
A
A
D
B
C
Figure 24. Belt Routing
A. Upper Wiring Harness
B. Final Wiring Harness
C. Mounting Clip
B
D. Chute Rotation Motor Connector
Figure 26. Latch Pin Removal
A. Hitch Latch Pin
B. Hitch
C. Frame Support Fingers
D. Quick Clips
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal
11. Slide the hitch assembly (A, Figure 27) forwards until
the hitch mounting arms (C) are free of the hitch sup-
port shaft (B).
12. Slide the hitch to the right to move it from under the
tractor.
NOTE: The hitch support shaft (B) may be left in posi-
tion and will not interfere with the operation of the lawn
mower deck.
IMPORTANT NOTE
Inspect the snow thrower assembly, hitch
assembly, snow thrower drive belt and all com-
ponent parts for signs of wear or damage.
Have these items repaired or serviced before
reinstalling the snow thrower onto the tractor.
C
B
A
Figure 27. Hitch Removal
A. Hitch Assembly
B. Hitch Support Shaft
C. Hitch Mounting Arms
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUFACTURING, INC.
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997
PRODUCTS
535 Macon Street
McDonough, GA 30253
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997
AGCOLawn.com
© Copyright 2006 Simplicity Manufacturing, Inc.
All Rights Reserved. Printed in USA.
Download from Www.Somanuals.com. All Manuals Search And Download.
|