OPERATOR’S
MANUAL
Intermediate
Snowthrower Models
Mfg. No.
7800084
7800086
7800085
7800087
7800138
Description
I75246E, 7.5HP OHV, Electric Start
EI75246E, 7.5HP OHV, Electric Start (CE)
I7524E, 7.5HP OHV, Electric Start
I7524EX, 7.5HP OHV, Manual Start (CE)
EI75246, 7.5HP OHV, Manual Start (CE)
7100723
Revision 00
Rev. Date 6/14/2006
TP 100-5190-00-IS-SN
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Rules & Information
This machine is capable to amputating hands and feet and throwing objects. Read these safety rules and
follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury
or death to you, or bystanders, or damage to property or equipment. The triangle
important safety information which must be followed.
in text signifies
TRAINING
OPERATION
1. Read, understand, and follow all instructions on the
machine and in the manuals before operating this
unit. Be thoroughly familiar with the controls and the
proper use of the equipment. Know how to stop the
unit and disengage the controls quickly.
1. Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
2. Exercise extreme caution when operating on or
crossing gravel drives, walks, or roads. Stay alert for
hidden hazards or traffic.
2. Never allow children to operate the equipment.
Never allow adults to operate the equipment without
proper instruction.
3. After striking a foreign object, stop the engine (motor),
remove the wire from the spark plug, disconnect the
cord on electric motors, thoroughly inspect the
snowthrower for any damage, and repair the damage
before restarting and operating the snowthrower.
4. If the unit should start to vibrate abnormally, stop the
engine (motor) and check immediately for the cause.
Vibration is generally a warning of trouble.
5. Stop the engine (motor) whenever you leave the
operating position, before unclogging the
collector/impeller housing or discharge guide, and
when making any repairs, adjustments, or inspec-
tions.
6. When cleaning, repairing, or inspecting make certain
the collector/impeller and all moving parts have
stopped. Disconnect the spark plug wire and keep
the wire away from the plug to prevent accidental
starting.
7. Do not run the engine indoors except for starting the
engine or for transporting the snowthrower in or out of
the building. Open the outside doors; exhaust fumes
are dangerous.
8. Exercise extreme caution when operating on slopes.
Do not attempt to clear steep slopes.
9. Never operate the snowthrower without proper
guards, plates, or other safety protective devices in
place and working.
10. Never direct the discharge toward people or areas
where property damage can occur. Keep children
and others away.
11. Do not overload the machine capacity by attempting
to clear snow at too fast a rate.
12. Never operate the machine at high transport speeds
on slippery surfaces. Look behind and use care
when operating in reverse.
13. Disengage power to the collector/impeller when
snowthrower is transported or not in use.
14. Use only attachments and accessories approved by
the manufacturer of the snowthrower (such as wheel
weights, counterweights, or cabs).
15. Never operate the snowthrower without good visibility
or light. Always be sure of your footing, and keep a
firm hold on the handles. Walk, never run.
16. Never touch a hot engine or muffler.
17. Never operate the snowthrower near glass enclo-
sures, automobiles, window wells, drop-offs, and the
like without proper adjustment of the discharge angle.
18. Never direct discharge at bystanders or allow anyone
in front of the unit.
3. Keep the area of operation clear of all persons, partic-
ularly small children and pets.
4. Exercise caution to avoid slipping or falling especially
when operating in reverse.
PREPARATION
1. Thoroughly inspect the area where the equipment is
to be used and remove all doormat, sleds, boards,
wires, and other foreign objects.
2. Disengage all clutches and shift into neutral before
starting engine (motor).
3. Do not operate the equipment without wearing ade-
quate winter outer garments. Wear footwear that will
improve footing on slippery surfaces. Avoid loose fit-
ting clothing that can get caught in moving parts.
4. Handle fuel with care; it is highly flammable.
(a) Use an approved fuel container.
(b) Never add fuel to a running engine or hot engine.
(c) Fill fuel tank outdoors with extreme care. Never fill
fuel tank indoors. Replace fuel cap securely and
wipe up spilled fuel.
(d) Never fill containers inside a vehicle or on a truck
or trailer bed with a plastic liner. Always place con-
tainers on the ground, away from your vehicle, before
filling.
(e) When practical, remove gas-powered equipment
from the truck or trailer and refuel it on the ground. If
this is not possible, then refuel such on a trailer with a
portable container, rather than from a gasoline dis-
penser nozzle.
(f) Keep nozzle in contact with the rim of the fuel tank
or container opening at all times, until refueling is
complete. Do not use a nozzle lock-open device.
(g) Replace gasoline cap securely and wipe up spilled
fuel.
(h) If fuel is spilled on clothing, change clothing imme-
diately.
5. Use extension cords and receptacles as specified by
the manufacturer for all units with electric drive
motors or electric starting motors.
6. Adjust the collector housing height to clear gravel or
crushed rock surfaces.
7. Never attempt to make any adjustments while the
engine (motor) is running (except when specifically
recommended by the manufacturer).
8. Let engine (motor) and machine adjust to outdoor
temperatures before starting to clear snow.
9. Always wear safety glasses or eye shields during
operation or while performing an adjustment or repair
to protect eye from foreign objects that may be
thrown from the machine.
19. Never leave a running unit unattended. Always disen-
gage the auger and traction controls, stop engine,
and remove keys.
20. Do not operate the unit while under the influence of
alcohol or drugs.
TP-600-3606-03-LW-UV
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Rules
21. Keep in mind the operator is responsible for acci-
dents occurring to other people or property.
8. Always follow the engine manual instructions for stor-
age preparations before storing the unit for both short
and long term periods.
9. Always follow the engine manual instructions for
proper start-up procedures when returning the unit to
service.
10. Maintain or replace safety and instruction labels as
necessary.
11. Keep nuts and bolts tight and keep equipment in
good condition.
12. Never tamper with safety devices. Check their proper
operation regularly and make necessary repairs if
they are not functioning properly.
22. Data indicates that operators, age 60 years and
above, are involved in a large percentage of power
equipment-related injuries. These operators should
evaluate their ability to operate the unit safely enough
to protect themselves and others from injury.
23. DO NOT wear long scarves or loose clothing that
could become entangled in moving parts.
24. Snow can hide obstacles. Make sure to remove all
obstacles from the area to be cleared.
CHILDREN
13. Components are subject to wear, damage, and dete-
rioration. Frequently check components and replace
with manufacturer’s recommended parts, when nec-
essary.
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the
unit and the operating activity. Never assume that children
will remain where you last saw them.
14. Check control operation frequently. Adjust and ser-
vice as required.
1. Keep children out of the area and under the watchful
15. Use only factory authorized replacement parts when
making repairs.
care of another responsible adult.
2. Be alert and turn unit off if children enter the area.
3. Never allow children to operate the unit.
4. Use extra care when approaching blind corners,
shrubs, trees, or other objects that may obscure
vision.
16. Always comply with factory specifications on all set-
tings and adjustments.
17. Only authorized service locations should be utilized
for major service and repair requirements.
18. Never attempt to make major repairs on this unit
unless you have been properly trained. Improper ser-
vice procedures can result in hazardous operation,
equipment damage and voiding of manufacturer’s
warranty.
CLEARING A CLOGGED DISCHARGE
CHUTE
Hand contact with the rotating impeller inside the dis-
charge chute is the most common cause of injury associ-
ated with snowthrowers. Never use your hand to clean
out the discharge chute.
19. Check shear bolts and other bolts at frequent inter-
vals for proper tightness to be sure the equipment is
in safe working condition.
To clear the chute:
1. SHUT OFF THE ENGINE.
EMISSIONS
1. Engine exhaust from this product contains chemicals
known, in certain quantities, to cause cancer, birth
defects, or other reproductive harm.
2. If available, look for the relevant Emissions Durability
Period and Air Index information on the engine emis-
sions label.
2. Wait 10 seconds to be sure the impeller blades have
stopped rotating.
3. Always use a clean out tool, not your hands.
SERVICE, MAINTENANCE, AND STORAGE
1. Check shear bolts and other bolts at frequent inter-
vals for proper tightness to be sure the equipment is
in safe working condition.
2. Never store the machine with fuel in the fuel tank
inside a building where ignition sources are present
such as hot water and spacer heaters, or clothes dry-
ers. Allow the engine to cool before storing in any
enclosure.
3. Always refer to the operator’s manual for important
details if the snowthrower is to be stored for an
extended period.
4. Maintain or replace safety and instruction labels as
necessary.
5. Run the machine a few minutes after throwing snow
to prevent freeze-up of the collector/impeller.
6. If fuel is spilled, do not attempt to start the engine but
move the machine away from the area of spillage and
avoid creating any source of ignition until fuel vapors
have dissipated.
7. Always observe safe refueling and fuel handling prac-
tices when refueling the unit after transportation or
storage.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Identification Numbers
North
American / CE
Models
CE Models
(only)
ID Tag Location
PRODUCT REFERENCE DATA
Model Description Name/Number
Identification Numbers
When contacting your authorized dealer for replace-
ment parts, service, or information you MUST have
these numbers.
Unit MFG Number
Unit SERIAL Number
Date Purchased
Record your model name/number, manufacturer’s identi-
fication numbers, and engine serial numbers in the
space provided for easy access. These numbers can be
found in the locations shown.
Dealer Name
NOTE: For location of engine identification numbers,
refer to the engine owner’s manual.
ENGINE REFERENCE DATA
Engine Make
Engine Model
Engine Type/Spec
Engine Code/Serial Number
CE IDENTIFICATION TAG MARKINGS
A. Manufacturer’s Identification Number (Part Number)
B. Manufacturer’s Serial Number
C. Power Rating in Kilowatts
D. Maximum Engine Speed in Rotations per Minute
E. Manufacturer’s Address
E
G
B
I
F. Year of Manufacture
G. CE Compliance Logo
A
H. Mass of Unit in Kilograms
I. Sound Power in Decibels *
J. Model Number
C
J
D
H
Sample Only
NOTE: Decal format and configuration may differ from
illustration.
F
See page 29 for actual CE compliance information.
* See page 29 for CE compliance information regarding
sound pressure and vibration.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Decals
All safety and instructional messages on your unit should
be carefully read and obeyed. Personal bodily injury can
result when these instructions are not followed. The
information is for your safety and it is important. The
safety decals below are on your unit.
GENERAL
This unit has been designed and manufactured to pro-
vide you with the safety and reliability you would expect
from an industry leader in outdoor power equipment
manufacturing.
If any of these decals are lost or damaged, replace them
at once. See your local dealer for replacements.
Although reading this manual and safety instructions it
contains will provide you with the necessary basic knowl-
edge to operate this equipment safely and effectively, we
have placed several safety labels on the unit to remind
you of this important information while you are operating
your unit.
These labels are easily applied and will act as a constant
visual reminder to you, and others who may use the
equipment, to follow the safety instructions necessary for
safe, effective, operation.
NORTH AMERICAN
MODEL DECALS
Auger
Engage
Auger
Disengage
1726946
Part No. 7100821
WARNING / Main Dash Decal, North American Models
Part No. 1726946
Auger Control Decal
DANGER
Amputation hazard
Contact with the auger will cause
serious injury.
• Keep hands, feet, and clothing
away.
• Shut off engine before servicing.
1716532
Part No. 1722867
Lubrication Decal
Part No. 1716532
Auger Danger Decal
Part No. 1733057
Discharge Chute Danger Decal
CE MODEL DECALS
1727023
Part No. 1727023
Auger Control Decal
Part No. 7100822
WARNING / Main Dash Decal, CE Models
Part No. 1727207
Discharge Chute Danger Decal
Part No. 1727208
Auger Danger Decal
Part No. 1722867
Lubrication Decal
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CE Safety Icons & Compliance Specs
Warning: Read Operator’s Manual.
Danger: Dismemberment.
Read and understand the Operator’s
Manual before using this machine.
The auger can amputate limbs. Keep
hands and feet away from auger and
rotating parts. Keep bystanders and
children away when engine is running.
Danger: Thrown Objects.
This machine is capable of throwing
objects and debris. Keep bystanders
away.
Danger: Dismemberment.
The impeller can amputate limbs.
Stop the engine, remove the key, and
disconnect spark plug wire before
clearing the discharge chute or per-
forming service work. Keep hands
and feet away from impeller and rotat-
ing parts.
Warning: Remove Key Before
Servicing.
Remove the key, disconnect spark
plug wire, and consult technical litera-
ture before performing repairs or
maintenance.
Danger: Breathing Hazard.
Danger: Burn Hazard.
Never touch a hot engine or muffler.
Do not run the engine indoors except
for starting the engine or for transport-
ing the snowthrower in or out of the
building. Open the outside doors;
exhaust fumes are dangerous.
Danger: Remove Key Before
Refueling.
Stop engine, remove key, and wait at
least 2 minutes before refueling.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Features, Controls, &
Operation
Please take a moment
and familiarize
ALL MODELS
yourself with the
name, location, and
function of these
controls so that you will
better understand the
safety and operating
instructions provided in
this manual.
1,2..
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Features & Controls
CONTROL LOCATIONS
The information below briefly describes the function of individual controls. Starting, stopping, and driving require the
combined use of several controls applied in specific sequences. To learn what combination and sequence of controls
to use for various tasks see the OPERATION section.
Speed Selector
Fuel
1,2..
Selects forward speeds 1-5 and reverse speeds 1-2.
Fuel tank filler cap (see illustration). Note: The fuel shut
off valve is located under the fuel tank. Close the valve
when the snowthrower is not in use. Open the valve
before starting.
Traction Control / Free Hand™ Lock
Engages traction drive to wheels when depressed. Also
locks auger control when depressed simultaneously.
Releasing the traction control lever releases the Free
Hand™ auger control lock and stops the drive wheels.
Starter Handle
Used to pull-start the engine.
Primer Button
Auger Control
Engages the auger/impeller when depressed. Releasing
the control stops the auger/impeller.
Primes carburetor for faster cold starting.
Engine Key
Chute Direction Control
Rotates the discharge chute to desired position.
Chute Deflector Knob
Prevents starting of engine without key. Stops engine
when removed.
Choke Knob
Locks chute deflector in desired position.
Traction Lock Pins
Adjusts air/fuel mix for easier cold weather starting.
On/Off Switch
The traction drive to each wheel can be locked and
unlocked with the Traction Lock Pins (H, Figure 4) to per-
mit the unit to “free-wheel,” allowing easier manual han-
dling and transport of the snowthrower.
Prevents starting of engine.
Electric Start Button (Optional)
Activates electric starter.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine Controls
STARTING CONTROLS
See Figure 1 for the following instructions.
Briggs &
Stratton OHV
Models
E
F
B
A
Units with Optional Electric Start
C
A. Electric Start Button (North American Models)-
The electric start button (A) activates an electric
starter mounted to the engine, eliminating the need to
pull the starter handle. The electric start button oper-
ates on 120 Volts AC, which is provided by connec-
tion to the extension cord provided with units
equipped with this feature. Connect this extension
cord ONLY to a properly grounded 3 prong elec-
trical outlet.
D
G
Electric Start Button (CE Models)- Please refer to
the detailed instructions supplied with the electric
start kit.
Figure 1. Engine Controls
A. Electric Start Button
B. Fuel Valve
E. Engine Key
F. Choke Knob
Manual Start
C. Starter Handle
D. Primer Button
G. On/Off Switch
B. Fuel Valve - The fuel valve (B) is located under the
fuel tank. It is used to turn the fuel supply off for out-
of-season storage.
C. Starter Handle - The starter handle (C) connects to a
starter cord to manually start the engine. Pulling
starter handle rapidly spins the engine crankshaft,
cycles the engine, and generates the spark neces-
sary for starting the engine.
D. Primer Button - When pressed, the primer button
(D) provides initial fuel to help start a cold engine.
Normally, pressing the primer button twice will pro-
vide enough fuel to start a cold engine.
E. Engine Key - The engine key (E) prevents the
engine from being started by unauthorized individu-
als. The key must be fully inserted into the key slot
for the unit to start. The key is also used to stop the
engine by pulling the key out of the key slot.
F. Choke Knob - The choke knob (F) adjusts the
air/fuel mixture, and is used to help start a cold
engine by providing a richer mixture. Once the engine
is warm and running smoothly, the choke knob
should be set to the off position to provide a normal
air/fuel mix.
G. On/Off Switch - The on/off switch (G) prevents the
engine from being started. The switch must be ON for
the unit to start.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls
GROUND SPEED CONTROLS
A. Speed Selector - This lever (A, Figures 2 & 3) is
B
A
D
C
used to set the ground speed of the snowthrower.
The snowthrower has five forward speeds, 1–5, and
two reverse speeds, 1–2. No neutral position or gate
is required, since the traction drive design automati-
cally provides "neutral" (no forward or reverse move-
ment), whenever the drive control is released.
B. Traction & Free Hand™ Control - This control
engages the traction drive as the lever (B, Figures 2
& 3) is depressed, and disengages the traction drive
when the lever is released. When both levers are
depressed the Free Hand™ control is activated. This
allows the auger control to be released yet the auger
remains engaged until the traction Free Hand™ is
released. NOTE: Changing ground speeds must only
be done while the drive control is in the disengaged
(fully released) position.
Figure 2. Operator's Control Position
A. Speed Selector
B. Drive Control
C.Auger Control
D.Chute Direction Control
AUGER CONTROL
C. Auger Control - The auger control clutch lever (C
Figures 2 & 3), engages the auger drive when the
lever is depressed and disengages the auger drive
when the lever is released (unless Traction Free
Hand™ control is also depressed-see above).
D
A
B
C
DEFLECTOR CONTROLS
E
F
D. Chute Direction Control - The chute direction con-
trol (D, Figures 2 & 3), allows the discharge chute to
be rotated to throw snow in the desired direction.
Snow may be thrown at any angle from straight left,
to straight forward, to straight right.
I
E. Chute Deflector - Controls the distance snow is
thrown. Tilting the chute deflector (E, Figure 3) UP
provides a higher stream and greater distance, while
tilting the deflector DOWN provides a lower stream
and less distance.
G
F. Chute Deflector Knob - This knob (F, Figure 3)
allows the discharge chute deflector (E) to be locked
in the desired tilt position.
H
Figure 3. Snowthrower Controls
A. Speed Selector
B. Drive Control
C. Auger Control
D. Chute Control Knob
E. Chute Deflector
F. Chute Deflector Knob
G. Skid Shoes
H. Scraper Bar
I. Traction Lock Pins
SCRAPER HEIGHT
G, H. Scraper Bar Height Control - The skid shoes (G,
Figure 3) control the height of the scraper bar (H).
(NOTE: On later models, the scraper bar is also
adjustable.) The scraper bar allows smooth surfaces
(such as concrete or asphalt driveways) to be
scraped clean of snow. On surfaces such as gravel,
the scraper bar should be adjusted higher — so that
it will not pick up gravel or debris.
TRACTION LOCK CONTROL
I. Traction Lock Pins - The traction drive to each
wheel can be locked and unlocked with the traction
lock pins (I, Figure 3) to permit the unit to “free-
wheel,” allowing easier manual handling and transport
of the snowthrower.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
GENERAL OPERATION
WARNING
This unit is a “two-stage” snowthrower.
CHECKS BEFORE EACH START-UP
The first stage is the auger, which feeds the snow
back into the impeller housing. The second stage
is the impeller, which throws the snow out the
discharge chute. If bodily contact is made with
the auger or impeller when they are rotating,
severe personal injury will occur.
1. Make sure all safety guards are in place and all nuts,
bolts and clips are secure.
2. Check to make sure that the clean-out tool is
attached to the handle on the machine. Do not oper-
ate the machine without the clean-out tool properly
stored on the handle.
To avoid injury, keep others and yourself away
from the auger and the discharge chute whenever
the engine is running. Read and follow all of the
safety rules and warnings in this manual.
3. Check the engine oil level. See your engine owner’s
manual for procedure and specifications.
4. Check to make sure spark plug wire is attached and
spark plug is tightened securely. If necessary, torque
spark plug to 15 ft. lbs.
DANGER
5. Check the fuel supply. Fill the tank no closer than 1/4
to 1/2 inch of top of tank to provide space for expan-
sion. See your engine owner’s manual for fuel recom-
mendations.
Do not clean out discharge chute with hands.
Contact with moving parts inside chute will cause
serious injury. Use clean-out tool provided with
machine. Use the following procedure to remove
objects or clear the chute:
6. Check the scraper bar to make sure it is set at the
desired height. Adjust the scraper bar height if neces-
sary. (See page 15.)
1. Stop the engine. Remove the key
2. Wait 10 seconds to be sure the auger/impeller
blades have stopped rotating.
3. Always use the clean-out tool. DO NOT use your
hands.
7. Check the drive control (B, Figure 2), and Auger
Control (C) for proper operation. The auger and
impeller must stop within 5 seconds of releasing the
Auger Control (C). If adjustment is required, see the
Service Section for procedures.
8. Check the chute direction control (D, Figure 2) for
proper operation. The discharge chute should rotate
freely in both directions. See the Service Section for
adjustment procedures and troubleshooting.
WARNING
For your safety, operation on slopes should be in
an up and down direction only. If it becomes
necessary to move across the face of a slope, use
caution and do not blow snow. Be very careful
when changing direction on a slope.
9. Check the chute deflector (E, Figure 3) for proper
operation. The deflector should pivot freely up and
down when the chute deflector knob is loosened. If
adjustment is required, see the Service Section for
procedures.
Proper winter footwear is recommended for the
operator to help prevent slipping. Never attempt
to clean snow from excessively steep slopes. The
maximum slope for any operation is 17.7% (10º).
10. Position the chute at the desired starting direction
and set the deflector at the desired angle.
11. Check the speed selector (A, Figure 2) for smooth
operation. The control must move freely into each
speed position gate and remain in position when
released. If the speed selector does not move freely
into all forward and reverse speed positions, contact
your local authorized dealer for assistance.
WARNING
Gasoline is highly flammable and must be
handled with care. Never fill the tank when the
engine is hot or running. Always move outdoors
to fill the tank. Keep snowthrower and gasoline
away from open flame or spark.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
STARTING THE ENGINE
1. Turn the fuel valve (B, Figure 4) to the ON position.
E
F
B
Briggs &
Stratton
Models
A
2. Turn the On/Off switch (G) to the ON position.
3. Insert the engine key (E) into the engine key slot and
push fully in to the RUN position.
D
4. Fully close the choke (F) if engine is cold. (Do not
choke a warm engine.)
5. Push the primer button (D) two times if engine is cold.
(Do not prime a warm engine.)
6. Pull starter handle (C) rapidly, or push starter button
if equipped with the electric start. Do not allow the
starter handle to snap back—let the starter rope
rewind slowly—while keeping a firm grip on the
starter handle.
G
Figure 4. Engine Controls
A. Electric Start Button
B. Fuel Valve
C. Starter Handle
D. Primer Button
E. Engine Key
7. As the engine starts and begins to operate evenly,
open the choke (F) slowly. If the engine falters, turn
the choke knob clockwise until the engine runs
smoothly, and let it run briefly before returning the
choke to the OPEN position.
F. Choke Knob
G. On/Off Switch
NOTE: The engine will not develop full power until it
reaches operating temperature.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
OPERATING THE SNOWTHROWER
1. Rotate the discharge chute to the desired direction.
B
A
D
C
2. Set the speed selector to the desired forward speed.
3. Fully press and hold the auger control (C, Figure 5)
on the right-hand grip to begin auger rotation. To dis-
engage the auger, completely release the lever.
4. Fully press and hold the traction drive control lever
(B, Figure 5) on the left-hand grip to engage the trac-
tion drive and begin moving the snowthrower. To dis-
engage the traction drive, completely release the
lever. If engaged at the same time, the drive control
(B) will lock the auger control (C) in the engaged
position. Releasing the drive control (B) will release
the auger control (C).
5. Select forward or reverse speeds as needed using
the speed selector (A, Figure 5). Release the drive
control lever whenever changing drive speeds.
Figure 5. Operator's Control Position
A. Speed Selector
B. Drive Control
C. Auger Control
D. Chute Direction Control
NOTE: After 5 - 10 hours of use, it may be necessary
to adjust the tension on the traction drive cable. See
"Traction Drive Clutch Cable Adjustment" in the
Service Section for the adjustment procedure.
CLEARING A CLOGGED DISCHARGE
CHUTE
Hand contact with the rotating auger/impeller inside the
discharge chute is the most common cause of injury
associated with snowthrowers. DO NOT use your hand
to clean out the discharge chute. To clear the chute:
1. Stop the engine. Remove the key.
2. Wait 10 seconds to be sure the auger/impeller blades
have stopped rotating.
3. Always use the clean-out tool. DO NOT use your
hands.
GROUND SPEED SELECTOR
Use the speed selector (A, Figure 5) to control the drive
speed of the snowthrower. There are five forward speeds
and two reverse speeds.
Use the lower speeds to blow deep or wet snow. Use the
higher speeds to blow light snow or to drive the snow-
thrower without blowing snow.
To change speeds, first release the traction drive control
lever (B, Figure 5), then move the speed selector to the
desired speed setting. Fully press the traction drive con-
trol lever to resume operation.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
DEFLECTOR
The distance of the discharged snow is mainly controlled
by the position of the deflector (Figure 6).
Chute
Deflector Knob
The more the deflector is tilted UP, the farther snow will
be thrown. Loosen the deflector knob, tilt the deflector
UP or DOWN, and then retighten the knob when the
desired angle has been chosen.
Chute
Deflector
Figure 6. Chute Deflector Adjustment
SCRAPER BAR & SKID SHOES
On smooth surfaces such as concrete or asphalt, the
scraper bar should scrape the surface. On surfaces such
as gravel, the scraper bar should be high enough so that
it will not pick up gravel or debris.
The height of the scraper bar is controlled by raising or
lowering the skid shoes (See Figure 7).
Scraper
Bar
Skid Shoe
Nuts
1. To raise the scraper bar height, rest the scraper bar
on a strip of wood equal in thickness to the desired
height.
2. Make sure the scraper bar is parallel to the ground
surface.
Skid Shoe
3. Loosen the skid shoe nuts and let the skid shoes
drop to the surface.
Figure 7. Skid Shoe Adjustment
4. Tighten the nuts, making sure the skid shoes are
adjusted equally and are parallel to the surface.
5. To lower the height of the scraper bar, raise the skid
shoes.
Scraper Bar
Nuts
6. If the scraper bar becomes worn, it can be replaced
by removing the hardware attaching it to the
snowthrower.
The scraper bar is adjustable. (See Figure 8). If desired
scraper bar height adjustment cannot be achieved solely
by raising or lowering the skid shoes:
Scraper
Bar
1. Loosen the nuts securing the scraper bar to the
auger housing, and raise or lower the scraper bar
until desired height is achieved.
2. Tighten the nuts, making sure the scraper bar is
parallel with the bottom edge of the auger housing.
Figure 8. Scraper Bar Adjustment
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
FREE-WHEELING AND
TRACTION DRIVE LOCK
For easy turning when pushing the snowthrower, you
can disengage the traction drive at one or both wheels
by using the traction lock pins (See Figures 9 & 10).
Klik-Pin In
OUTER Hole
1. Turn the unit off, remove the engine key, and discon-
nect the spark plug wire.
2. To DISENGAGE the traction drive lock, insert the
traction lock pin through the outer hole in the axle.
(See Figure 9).
3. To ENGAGE the traction drive lock, insert the pin
through the hub and axle (See Figure 10). If the hole
in the hub is not aligned with the inner hole in the
axle, push the snowthrower until the holes align and
install the traction lock pin.
NOTE: When snowthrowing with the full width of the
auger, for best drive performance engage both wheels.
For easier turning when not using the full width of the
auger, engage one wheel and use the engaged side as
the snow contact side for the auger.
Figure 9. Traction Drive Lock - Disengaged
AFTER EACH USE
Klik-Pin In
INNER Hole
Normal use of the snowthrower may result in a build-up
of packed snow in and around the starter cord housing
and around engine controls. Heat from the engine will
usually prevent the snow from freezing solid while the
unit is running, but after the engine is shut down, some
snow may continue melting from engine heat, and later
freeze around some moving parts as the unit cools.
After each period of use, follow these steps to prevent
freeze-up caused by ice formation in and around the
engine controls and external parts.
1. Before shutting off the engine, pull the starter rope
out 2 - 3 times, and allow it to rewind slowly. This will
help clear packed snow from the starter cord area.
Allow the engine to run for several minutes.
Figure 10. Traction Drive Lock - Engaged
2. Stop the engine by pulling out the engine key.
3. Disconnect the spark plug wire, and position it away
from the spark plug.
WARNING
4. Brush snow and ice from the snowthrower. Be sure to
clear engine and snowthrower controls, discharge
chute, worm and chute rod gears, clutch cable areas,
and anywhere else snow has accumulated.
Never store snowthrower, with gasoline in engine
or fuel tank, in a heated shelter or in enclosed,
poorly ventilated enclosures. Gasoline fumes may
reach an open flame, spark or pilot light (such as
a furnace, water heater, clothes dryer, etc.) and
cause an explosion.
5. Always remove the engine key and store in a safe
place to prevent unauthorized use.
Handle gasoline carefully. It is highly flammable
and careless use can result in serious fire
damage to people and property.
6. If the snowthrower is kept in a cold shelter, fill the fuel
tank to prevent condensation. Do not store near
sparks or flame.
Drain fuel into an approved container outdoors
away from open flame or sparks.
Note: The engine owner’s manual contains further infor-
mation on preventing ice formation and freeze-up.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Regular
Maintenance
MAINTENANCE SCHEDULE
MAINTENANCE REQUIRED
FREQUENCY
NOTES
Benalene 900
Grease
Check auger gear case lubrication.**
Lubricate snowthrower.
25 Hours
10 Hours
Monthly
10W Oil and Grease
20 psi (1.37 bar)
See Engine Manual
See Engine Manual
N/A
Check tire pressure.
✛
✛
Change engine oil.*
50 Hours
✛
Clean or replace spark plug.
Yearly
4-6 Hours
Yearly
Check drive linkage/belt tension.
Lubricate Axle Shafts.
Lithium Grease
10W Oil
Check / Lubricate Free-Hand Linkage.
Lubricate Auger Shaft. ***
10 Hours
10 Hours
Lithium Grease
* Change original oil after two hours of operation.
**Check oil level each fall and spring.
***Lubricate each fall and spring.
✛ See your engine Owner’s Manual.
CHECKING TIRE PRESSURE
The air pressure in each tire (Figure 11) should be 20 psi
(1,36 kPa) and should be equal for both tires for best
performance. Be sure to keep caps on valves to prevent
entry of debris into the valve stem when tires are filled.
Figure 11. Checking Tire Pressure
CHECK AUGER
GEAR CASE LUBRICATION
1. Place the snowthrower on a level surface.
2. Remove the pipe plug (Figure 12).
3. Check the lubricant level. It should be level with the
lower edge of the plug opening. If not, add Benalene
900 grease (available from your dealer).
4. Re-install pipe plug, and tighten securely.
Pipe Plug
Figure 12. Checking Auger Gear Case Lubrication
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
LUBRICATION
IMPORTANT NOTE
It is very important that grease fittings on the auger shaft
are lubricated regularly. If auger rusts to shaft, damage to
worm gear may occur if shear pins do not break.
A
To prevent wheels rusting to axles, it is also necessary
to remove the wheels and grease the axles regularly.
Remove wheels and grease axles once each year.
B
There are two grease fittings on the auger shaft. Wipe
the fittings clean and apply grease, using a grease gun.
Also apply grease on other points indicated.
C
Apply medium weight (10W) oil to points shown (See
Figures 13 - 16).
Apply 5W-50 synthetic motor oil to the friction disc hex
shaft (see Figure 13).
Generally, all moving metal parts should be oiled where
contact is made with other parts. Keep oil and grease off
belts, pulley grooves, drive disc, and friction disc.
Figure 13. Drive Area Lubrication Points
(Bottom Cover Removed)
A. Drive Disc
C. Hex Shaft
B. Friction Disc
LUBRICATION NOTES:
Grease locations indicated by grease gun symbol.
Use grease fittings when present. Disassemble
parts to apply grease to moving parts when grease
fittings are not installed.
Oil locations indicated by oil can symbol. Do not
allow oil to drip onto traction drive or friction disc.
CAUTION
In order to keep the free-hand controls disengaging
properly when released, it is important to oil the free-
hand controls every 10 hours.
Figure 14. Snowthrower General Lubrication Points
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Storage
LUBRICATION CHECK / LUBRICATE
FREE-HAND LINKAGE
Check the function of the Free-Hand controls: the con-
trols should function as described in the CONTROLS
section. It is critical for the safe operation of the unit
that the controls disengage when released.
If the controls do not function properly, lubricate them. If
lubrication does not rectify the problem, see your dealer.
Under no circumstances should the unit be used if the
controls are not functioning properly.
Figure 15. Lubricate Free Hand Control
IMPORTANT NOTE
It is very important that grease fittings on the auger shaft
are lubricated regularly. If auger rusts to shaft, damage to
worm gear may occur if shear pins do not break.
LUBRICATING THE AUGER SHAFT &
ASSEMBLY
C
1. Remove cotter pin (C, Figure 16) and shear pin (B).
2. Use a grease gun and squirt several shots of grease
into grease fitting (A).
B
3. Rotate auger assembly (D) several times to distribute
the grease evenly. Repeat step 2.
A
B
4. Reinstall shear pin (B) and cotter pin (C).
5. Repeat procedure for other side.
C
A
STORAGE
D
WARNING
D
Never store the unit (with fuel) in an enclosed,
poorly ventilated structure. Fuel vapors can
travel to an ignition source (such as a furnace,
water heater, etc.) and cause an explosion.
Figure 16. Checking Auger Gear Case Lubrication
A. Grease Fittings
B. Shear Pins
C. Cotter Pins
D. Auger Assembly
Fuel vapor is also toxic to humans and animals.
Before you store your unit for the off-season, read the
Maintenance and Storage instructions in the Safety
Rules section, then perform the following steps:
Before starting the unit after it has been stored:
• Check all fluid levels. Check all maintenance items.
• Perform all recommended checks and procedures
found in the engine owner’s manual.
• Remove the key.
• Perform engine maintenance and storage measures
listed in the engine owner’s manual. This includes
draining the fuel system, or adding stabilizer to the
fuel (do not store a fueled unit in an enclosed struc-
ture - see warning).
• Allow the engine to warm up for several minutes
before use.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting,
Adjustment, & Service
TROUBLESHOOTING
WARNING
Before performing any adjustment or service to
snowthrower, stop the engine and wait for
moving parts to stop. Remove the key. To prevent
accidental starting, disconnect the spark plug
wire and fasten away from the plug.
This section provides troubleshooting and service
instructions. Locate the problem and check the possible
cause/remedy in the order listed.
Also, refer to the engine manufacturer’s Owner’s Manual
for additional information.
For problems not covered here, contact your local deal-
er.
PROBLEM
POSSIBLE CAUSE
REMEDY
1. Key is OFF.
1. Push key in to the ON position.
Engine fails to start.
2. Failure to prime cold engine
3. Fuel valve is in CLOSED position.
4. Out of fuel.
2. Press Primer Button twice and restart.
3. Turn valve to OPEN position.
4. Fill fuel tank.
5. Choke OFF - cold engine.
5. Turn choke to ON.
6. Turn choke to OFF; try starting.
7. Check gap. Gap plug, clean elec-
trode, or replace plug as necessary.
8. Drain tank (Dispose of fuel at an
authorized hazardous waste facility).
Fill with fresh fuel.
6. Engine flooded.
7. Spark plug not sparking.
8. Water in fuel, or old fuel.
9. On/Off switch Off.
9. Turn switch to ON.
1. Fuel mixture too rich.
1. Move choke to OFF position.
2. See your dealer for adjustments.
3. Clean and gap, or replace.
Engine starts hard or runs poorly.
Auger does not rotate.
2. Carburetor adjusted incorrectly.
3. Spark plug faulty, fouled, or gapped
improperly.
4. Fuel cap vent is blocked.
4. Clear vent.
1. Auger control not engaged.
1. Engage auger control.
2. Foreign matter blocking auger.
2. STOP engine and REMOVE the key.
DISCONNECT the spark plug wire.
Clear auger using clean-out tool. See
warning in SAFETY RULES.
3. Tighten to remove slack. See auger
clutch cable adjustment.
3. Auger drive clutch cable slack.
4. Check auger drive belt adjustment.
5. Replace belt.
4. Auger drive belt slipping.
5. Broken belt.
6. Replace shear pin.
6. Shear pin broken.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
PROBLEM
POSSIBLE CAUSE
REMEDY
1. Chute deflector too low.
1. Adjust deflector as necessary.
Auger rotates, but snow is not
thrown far enough
2. Ground speed too fast.
2. Use slower speed selector setting.
3. Snowthrower discharge chute clogged. 3. STOP engine and REMOVE the key.
DISCONNECT the spark plug wire.
Clear auger using clean-out tool. See
warning in SAFETY RULES.
4. Auger belt loose or worn.
4. Check auger drive belt adjustment
1. Scraper bar height improperly
adjusted.
1. RAISE skid shoes
LOWER scraper bar.
Scraper bar does not clean hard
surface.
1. Scraper bar height improperly
adjusted.
1. LOWER skid shoes
RAISE scraper bar.
Scraper bar picks up and throws
stones on gravel drive.
1. Tires slipping.
1. Check tire pressure and tread.
2. Lock traction lock pins.
Poor traction
2. Traction lock pins unlocked.
1. Auger clutch cable too tight or bent.
2. Auger drive belt out of adjustment.
3. Auger belt guide out of adjustment.
4. Free hand control not releasing.
1. Loosen or straighten clutch cable.
2. Adjust auger belt.
Auger does not stop when auger
lever is released
3. Adjust auger belt guide.
4. Lubricate free hand linkage.
1. Traction drive clutch cable bent or too
tight.
1. Loosen cable to remove slack or
replace. See adjustment procedure.
Snowthrower does not stop when
drive lever is released
1. Traction drive clutch cable loose.
1. Tighten to remove slack. See adjust-
ment procedure.
2. Replace drive belt.
Snowthrower does not drive when
drive lever is engaged.
2. Drive belt loose, broken, or stretched.
3. Drive roller chain damaged.
4. Traction lock pins in free-wheeling
position (OUTER hole).
3. Replace chain.
4. Change traction lock pins to INNER
hole to engage traction drive.
5. Replace disc (see your dealer).
5. Friction disc worn.
1. Gearing needs lubrication
2. Worm gear not adjusted properly.
1. Oil or grease as required.
2. Adjust worm gear. See adjustment
procedure.
Discharge control is difficult to
operate.
3. Adjust gear bracket. See adjustment
procedure.
3. Control rod gears misaligned.
4. Replace pin.
4. Pin connecting control shaft broken.
1. Tire pressure not equal.
2. One wheel is set in free-wheeling
mode. (Traction lock pin is in the
OUTER hole).
1. Check tire pressure.
Snowthrower veers to one side.
Excessive vibration.
2. Make certain BOTH traction lock pins
are in the INNER holes (to engage
traction drive).
1. Loose parts or damaged auger.
1. STOP engine and REMOVE the key.
DISCONNECT the spark plug wire.
Tighten all hardware. Replace auger
if necessary. If vibration continues,
see your dealer.
1. Traction drive out of adjustment.
1. Readjust drive, or shift speed selector
setting up one speed faster.
Drive fails to move snowthrower
at slow speeds.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments
SPEED SELECTOR PIVOT ADJUSTMENT
Adjust as follows:
A
1. Move the ground speed control (A, Figure 17) fully
forward.
2. Loosen the hardware (B) securing the upper and
lower shift rods.
3. Push the lower rod (C) down fully (into the housing).
B
4. Make sure the ground speed control (A) is in the full
forward (5th gear) position. Pull the two rods apart
and tighten the shift rod hardware (B).
C
Figure 17. Speed Selector Linkage Adjustment
A. Ground Speed Lever
B. Shift Rod Hardware
C. Lower Shift Rod
TRACTION DRIVE CLUTCH CABLE
ADJUSTMENT
Initial Adjustment
The traction drive clutch cable should initially be adjusted
so that there is no slack in the cable when moved slightly
from side to side, but bellcrank arm remains in fully down
position. To adjust tension on the cable:
Traction Drive
Clutch Cable
1. Loosen adjustment hex nut (Figure 18) by holding the
adjusting flats and turning adjustment hex nut.
2. Tighten adjustment screw by turning adjustment flats
and holding screw. The adjustment screw is a
phillips screw and the head can be held or turned by
inserting a screwdriver through the traction drive
clutch cable spring. Tighten just until slack in cable
is removed.
Adjustment
Flats
Adjustment
Hex Nut
Adjustment
Screw
3. Tighten hex nut securely. The unit should able to be
pushed forward and back freely.
Traction Drive
Clutch Cable Spring
Traction Drive
Bellcrank Arm
WARNING
Figure 18. Traction Drive Clutch Cable Adjustment
Do not over-tighten, as this may cause traction
drive to engage without depressing the traction
drive control (bellcrank arm must remain in down
position).
Run-In Adjustment
1. After 5 hours of use, check for proper adjustment.
Readjust clutch cable if necessary by increasing ten-
sion on cable. A small amount of bellcrank arm
movement is permissible if unit passes operating
checks described in the Caution at left. Optimal
adjustment provides 3/16" clearance between
traction drive disc and rubber ring on friction disc
when drive lever is released (see Figure 13 for fric-
tion disk location).
Verify that the cables are not over-tightened: With
speed selector in position 1 and traction drive
control fully released, push snowthrower forward.
The unit should move forward freely.
If unit does not move forward freely, the cable has
been over-tightened. To remedy, loosen tension
on clutch cable slightly, and recheck.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments
MANUAL DISCHARGE CHUTE
CONTROL LINKAGE ADJUSTMENT
E
A
Pinion Gear Adjustment
If the discharge chute is difficult to operate, first lubricate
the pinion gear (A, Figure 19) and ring gear (E). If it is
still difficult to operate, adjust as follows:
NOTE: If the discharge chute will not stay in position,
adjust the pinion gear (A) closer to the ring gear (E).
B
D
1. Loosen the bolts (C, Figure 19) which hold the pinion
gear bracket (D).
C
2. If the pinion gear is too tight against the ring gear,
move it away slightly and then retighten the bolts.
Figure 19. Discharge Control
A. Pinion Gear
B. Control Rod
C. Bolt (2)
3. Check the operation again.
D. Bracket
E. Ring Gear
CHUTE DIRECTION CONTROL
ROD GEAR ADJUSTMENT
If the discharge chute becomes difficult to rotate or
begins to operate erratically, the chute direction control
rod gears may require adjustment:
1. Loosen the gear bracket mounting nuts (Figure 20).
2. Slide the gear bracket into the position that provides
the best engagement between the gears.
3. Tighten the bracket mounting nuts, and check for
smooth operation.
Mounting Nuts
4. Readjust if necessary.
5. Lubricate the chute direction control rod gears with a
medium weight (10W) oil.
Figure 20. Chute Direction Gear Adjustments
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments
AUGER DRIVE CLUTCH CABLE
ADJUSTMENT
The auger drive clutch cable should be adjusted so that
there is no slack in the cable when moved slightly from
side to side. To adjust tension on the cable:
1. Loosen adjustment hex nut (Figure 21) by holding the
adjusting flats and turning adjustment hex nut .
Auger Drive
Clutch Cable
2. Tighten adjustment screw by turning adjustment flats
and holding screw. The adjustment screw is a
phillips screw and the head can be held or turned by
inserting a screwdriver through the auger drive clutch
cable spring. Tighten just until slack in cable is
removed.
Adjustment
Flats
Adjustment
Hex Nut
Adjustment
Screw
WARNING
Do not over-tighten, as this may lift the idler cable
lever and cause auger drive to be engaged
without depressing the Auger Control.
Auger Drive
Clutch Cable
Spring
Idler Rod
Right Handle
Figure 21. Auger Drive Clutch Cable Adjustment
3. Tighten hex nut securely.
4. Start unit and check auger. Auger must not be
engaged unless auger control is depressed.
5. With engine running, fully depress auger control, the
auger should engage and run normally.
6. Release auger control. Auger must stop within 5
seconds.
7. If auger does not operate properly, stop engine and
recheck clutch cable adjustments.
8. If clutch cable is properly adjusted, auger drive belt
tension may require adjustment. See "Adjusting
Auger Drive Belt" on next page.
Engine Pulley
DRIVE BELT ADJUSTMENT
Engine Pulley
Idler Pulley
The snowthrower is equipped with two drive belts locat-
ed just in front of the engine under the belt cover. Figure
22 shows both belts and idler pulleys. The belt nearest
the engine is the unit traction drive (wheels) belt. The
belt farthest from the engine is the auger/ impeller drive
belt.
Drive Belt
Idler Pulley
Auger Belt
Traction
Drive Pulley
The traction drive belt has constant tension provided by
a spring-loaded idler pulley arm, and is non-adjustable.
This belt rotates whenever the engine is running, and
provides power to the traction drive disc, which also
rotates constantly while the engine is running.
Front
Auger Pulley
(Auger)
The auger drive belt tension may be adjusted by moving
the auger drive idler pulley. See “Adjusting Auger Drive
Belt” on next page.
Figure 22. Drive Belt Paths
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments
DRIVE BELT ADJUSTMENT (Continued)
If the auger drive slips (auger slows or doesn't rotate nor-
mally while blowing snow), or stays engaged when the
control is disengaged — and the auger clutch cable has
been properly adjusted — the auger drive belt may be
out of adjustment.
Auger Control
Belt Cover
WARNING
Auger must NOT rotate unless the Auger Control
lever has been depressed. Proper Auger Drive
Belt adjustments stop the auger within 5 seconds
after the Auger Control is disengaged.
Figure 23. Auger Control and Belt Cover Location
Checking Auger Belt & Belt Guide
Adjustments
1. Insert the engine key and start the snowthrower.
Auger Drive
Clutch Cable
2. Engage and disengage the auger control a series of
ten times, checking that the auger comes to a com-
plete stop within 5 seconds after the control is disen-
gaged each time.
Adjustment
Hex Nut
3. If the auger comes to a complete stop each time with-
in 5 seconds, the adjustment is correct. If the auger
does NOT come to a complete stop within the neces-
sary 5 seconds, the adjustment is incorrect: readjust-
ing the auger belt & belt guide according to the pro-
cedures below.
Measure Spring
Length, Spring
Should Expand
5/16” When Auger
is Engaged
Adjusting Auger Drive Belt
1. Make certain that the snowthrower is off, the engine
key has been removed, and the spark plug discon-
nected.
Idler Rod
Right Handle
Figure 24. Auger Drive Clutch Cable
2. Check that there is no slack in the auger drive clutch
cable (see Figure 24). If there is, follow the auger
drive clutch cable Adjustment procedure on page 24.
Auger Idler
Pulley
3. Measure the length of the auger drive clutch spring
(Figure 24).
4. Fully depress the auger control and measure the
expanded length of the spring.
Auger Idler
Arm
The spring should expand 19/64”-5/16”. If the spring
deflection is less than 19/64”-5/16” the auger idler
pulley must be adjusted. Proceed to step 5.
5. Loosen the belt cover screws and remove the belt
cover (Figure 23)
Adjustment
Bolt
Auger
Drive Belt
6. Loosen the adjustment bolt (see Figure 25) and move
the auger idler pulley.
7. Tighten the adjustment bolt and repeat steps 3-4.
Figure 25. Auger Drive Belt, Guide and Pulley
8. Test run the unit. The auger must NOT rotate unless
the auger control lever has been depressed. Proper
auger drive belt adjustments stop the auger within 5
seconds after the auger control is disengaged. If the
auger drive fails either of these tests, repeat the
adjustment procedures.
9. After adjusting the auger drive belt, the auger belt
guide MUST BE adjusted according to the Adjusting
Auger Belt Guide procedure which follows.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments & Service
DRIVE BELT ADJUSTMENT (Continued)
Belt Guide
Screws
Adjusting Auger Belt Guide
1. With the auger control still fully depressed, adjust the
auger belt guide(s) so that there is a 1/64” gap (1/32”
Maximum) between the guide and the belt (Figures
26), making certain the guide is NOT putting pres-
sure on the belt.
Belt Guide
& Gap
2. Making certain the auger belt guide does NOT move
while doing so, tighten the auger belt guide screw
(Figures 26) to secure the guide.
3. Check the adjustment on the auger belt guide(s)
(Figures 26) to make certain that the gap between
the belt and the belt guide is correct.
Figure 26. Auger Belt Guide Adjustment
4. Disengage the auger control by removing the card-
board tube (or other means used to temporarily
secure the control.)
5. Test the unit by following the steps under the
“Checking Auger Belt & Belt Guide Adjustments”
above.
WARNING
Failure to properly adjust the Auger Belt Guide(s)
may cause auger to rotate when Auger Control
has not been depressed.
DRIVE BELT REPLACEMENT
WARNING
Snowthrower must move only when the traction
Drive Control is depressed, and must stop when
the lever is released (disengaged).
The snowthrower has two drive belts, one for the traction
drive—which transmits engine power to the wheels, and
a second for the auger drive—which transmits engine
power to the auger mechanism.
Traction Drive Belt & Pulley
Each of these drive belts are of special construction and
should be replaced only with genuine replacement belts
which match the original equipment belts. These are
available from your dealer.
Traction Drive Belt Replacement
1. Disconnect spark plug wire and fasten it away from
the spark plug.
2. Remove belt cover.
3. Pull the traction drive belt idler pulley arm (See
Figure 22) away from the belt to relieve tension, and
slide the belt off the engine pulley.
4. Slip the belt off from around the traction pulley (See
Figure 27) and pull the belt out of the unit between
the auger pulley and the traction pulley (the lower
cover need not be removed for this step).
Figure 27. Traction Drive Pulley
(Lower Cover Removed For Clarity)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
DRIVE BELT REPLACEMENT (Cont.)
Traction Drive Belt Replacement (Cont.)
WARNING
Auger must NOT rotate unless the Auger Control
lever has been depressed, and auger must stop
within 5 seconds after Auger Control lever has
been released.
5. Reverse the procedure to install the new belt. Be
sure there are no twists in the belt, and that the belt is
properly seated in the pulley grooves.
6. Replace the belt cover.
7. Start the unit, and check the traction drive for proper
operation. See "Traction Clutch Cable Adjustment"
for adjustment procedures.
WARNING
Do not go near the discharge chute or auger
when the engine is running. Do not run the engine
with any cover or guard removed.
Auger Drive Belt Replacement
1. Remove gas from fuel tank and run engine until it
stops running from lack of fuel.
Auger Drive Pulley
2. Disconnect spark plug wire and fasten it away from
the spark plug.
3. Remove belt cover (See Figure 23).
4. Loosen auger belt guide and slide belt off engine pul-
ley and away from idler pulley. (See Figure 26).
5. Clamp or tie auger control lever to handle in the fully
depressed position to release all tension on the auger
pulley brake pad, and provide clearance for belt
removal.
Auger Belt Stops
6. Tilt unit forward and rest on auger housing.
7. Remove lower cover.
Figure 28. Auger Drive Pulley and Belt Stops
8. Loosen hex screw securing belt stop (Figure 28), and
pivot the belt stop away from the pulley to permit
removal of belt.
9. Pull the belt out of the unit, and install the new belt on
the auger drive pulley.
10. Position belt stop to provide 1/8" clearance between
stop and belt, and and tighten securely.
11. Replace lower cover.
12. Return unit to normal upright operating position.
13. Release auger control.
14. Install auger belt over engine pulley.
15. Adjust auger belt stop as described under ADJUST-
ING BELT GUIDES.
16. Install belt cover.
17. Connect spark plug wire and fill fuel tank.
18. Start unit and check auger for proper operation. See
"Auger Drive Clutch Cable Adjustment" for adjust-
ment procedures if additional adjustment is neces-
sary.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
ROLLER CHAIN REPLACEMENT
NOTE: This procedure does not apply to models that use
an “endless” chain.
Keeper link
(Must install towards wheel side
1. Remove gas from fuel tank and run engine until it
stops running from lack of fuel.
with open end trailing.)
2. Disconnect spark plug wire and fasten it away from
the spark plug.
3. Tilt the snowthrower forward and carefully rest unit
on the auger end.
Master link
4. Rotate the wheel to locate the roller chain master link.
5. Remove the keeper link, master link and chain.
6. Install new chain and master link as shown in Figure
29.
7. Return snowthrower to upright operating position.
8. Connect spark plug wire and fill fuel tank.
Direction of travel
Figure 29. Roller Chain Master Link
SHEAR PIN REPLACEMENT
WARNING
Do not go near the discharge chute or auger
when the engine is running. Do not run the engine
with any cover or guard removed.
B
Under most circumstances, if the auger strikes an object
which could cause damage to the unit, the shear pin will
break. (This protects the gear box and other parts from
damage.)
A
The shear pins are located on the auger shaft as shown
in Figure 30. To replace the shear pins, tap out broken
pin with a pin punch, and install a new shear pin and cot-
ter pin. Spread the legs of the new cotter pin fully. Do
NOT replace shear pins with anything other than the
correct grade replacement shear pin. See the
A
B
REPLACEMENT PARTS section at the back of this man-
ual for the correct part numbers. (Use of bolts, screws or
a harder shear pin will lead to damaged equipment.)
Figure 30. Shear Pin Replacement
A. Shear Pin B. Cotter Pin
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
NOTE: Specifications are correct at time of printing and are subject to change without notice.
* Actual sustained equipment horsepower will likely be lower due to operating limitations and environmental factors.
ENGINE:
CHASSIS:
Wheels
Inflation Pressure: 20 psi (1,37 bar)
190 Degrees
10” (25.4 cm) 4 Blade Ribbon Flighted Steel
Friction Disc, 5 Forward Speeds, 2 Reverse
Spout Rotation
Impeller
Drive System
7.5 HP* Briggs & Stratton OHV
Make
Model
Briggs & Stratton
Intek Snow
Horsepower
Displacement
Oil Capacity
7.5 HP @ 3600 rpm
12.6 Cu. in (206 cc)
20 oz. (,59 L)
DIMENSIONS
Effective Clearing Width
-I75246E, EI75246E,
I7524E, I7524EX,
EI75246
24” (65 cm)
7.5 HP* Briggs & Stratton OHV (Euro)
Make
Model
Briggs & Stratton
Intek Snow
Horsepower
Displacement
Oil Capacity
7.5 HP @ 3600 rpm
12.6 Cu. in (206 cc)
20 oz. (,59 L)
Length
-I75246E, EI75246E,
I7524E, I7524EX,
EI75246
51” (132 cm)
43” (109cm)
158 lbs. (72 kg)
Height
-I75246E, EI75246E,
I7524E, I7524EX,
EI75246
Weight
-I75246E, EI75246E,
I7524E, I7524EX,
EI75246
CE COMPLIANCE SPECIFICATIONS
Kilowatts (kW)
(@ Governed
RPM’s)
Vibration at
RPM’s
(Governed)
Sound Power Sound Pressure
Model
Unit Mass (kg)
2
(LWA) (dBA)
(LPA) (dBA)
Handle (m/s )
EI75246E
I7524EX
EI75246
3600
3600
3600
5.6
5.6
5.6
72
72
72
105
105
105
90
90
90
8.5
8.5
8.5
Technical Information
Power Ratings
The power ratings for an individual engine model are initially developed by starting with SAE (Society of Automotive
Engineers) code J1940 (Small Engine Power & Torque Rating Procedure) (Revision 2002–05). Given both the wide
array of products on which our engines are placed, and the variety of environmental issues applicable to operating
the equipment, it may be that the engine you have purchased will not develop the rated horsepower when used in a
piece of power equipment (actual “on–site” power). This difference is due to a variety of factors including, but not lim-
ited to, the following: differences in altitude, temperature, barometric pressure, humidity, fuel, engine lubrication, max-
imum governed engine speed, individual engine to engine variability, design of the particular piece of power equip-
ment, the manner in which the engine is operated, engine run–in to reduce friction and clean out of combustion
chambers, adjustments to the valves and carburetor, and other factors. The power ratings may also be adjusted
based on comparisons to other similar engines utilized in similar applications, and will therefore not necessarily match
the values derived using the foregoing codes.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
SRecptlaiocnemToepnitcXPXaXrXts & Accessories
REPLACEMENT PARTS
TECHNICAL MANUALS
Replacement parts are available from your authorized
Additional copies of this manual are available, as well as
dealer. Always use genuine Simplicity / Snapper Service fully illustrated parts lists. These manuals show all of the
Parts.
product’s components in exploded views (3D illustrations
which show the relationship of parts and how they go
together) as well as part numbers and quantities used.
Important assembly notes and and torque values are
also included.
MAINTENANCE ITEMS
Many convenient and helpful service and maintenance
items are available from your authorized dealer. Some of
these items include:
For applicable manuals currently available for your
model, contact our Customer Publications Department at
262-284-8519 (Simplicity Manufacturing Inc.) or 1-866-
313-6682 (Snapper). Have the information listed in the
box below available when phoning in your request.
Technical manuals can be downloaded from
Engine Oil
Tire Sealant
Degrimer/Degreaser
Gas Stabilizer
Touch-Up Paint
Grease Gun Kit
8 oz. Grease Tube
Model:
Mfg. No.:
Your Name:
Address:
City, State, Zip:
Visa/Mastercard No.:
Card Expiration Date:
30
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUFACTURING, INC.
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997
© Copyright 2006, Simplicity Manufacturing, Inc.
All Rights Reserved. Printed in USA.
Download from Www.Somanuals.com. All Manuals Search And Download.
|