Light Kit
Part No. 1695295
Installation
For Axion and 150Z Zero Turn Models
Instructions
1
1
2
4
2
4
5
6
3
3
Kit Contents:
Ref. Part No. Qty. Description
1
2
3
4
N/A
N/A
N/A
1726801
2
2
2
2
NUT, Hex, 5/16-18
LOCKWASHER, 5/16
CARRIAGE BOLT, 5/16-18 x 1
HEADLIGHT ASSEMBLY,
(Includes Ref. Nos. 1, 2, & 3)
SWITCH, Headlight
7
5
6
7
1716951
2172434
1726796
1
2
1
CLIP, Wire
HARNESS, Wire
Figure 1. Contents
WARNING
Before beginning any service work turn off the
PTO, set the parking brake, turn off the ignition,
remove the key, and disconnect the spark plug
wire(s).
B
C
D
A
INSTALLATION
1. Remove 1/4-20 x 5/8 capscrews (A, Figure 2) and
cover (B).
F
2. Install light assembly (F) and secure with 5/16 lock-
washer (D) and 5/16-18 nut (C).
E
3. Reinstall cover (B) and secure with 1/4-20 capscrews
(A).
4. Repeat steps 1 through 3 for other side of unit.
Figure 2. Light Installation
A. Capscrews, 1/4-20 x 5/8
B. Cover
C. Nut, 5/16-18
D. Lockwasher, 5/16
E. Bracket
F. Light Assembly
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Light Kit
Installation Instructions
Note: The side of the headlight wire harness with the
ribbed plastic cover (C, Figure 6) connects to the left side
light. The side of the headlight wire harness with the
braided cover goes to the right side light.
D
13. Connect harness plug (B, Figure 6) to the back of the
headlight (A). Make sure the connector is fully seat-
ed into the light.
E
C
14. Slide wire clip (D) onto the back side of bracket (E)
as shown. Push down to secure.
B
15. Slide headlight wire harness (C) into wire clip (D).
Pull slack out of headlight wire harness (C) toward
engine compartment. Route wires so they do not
contact hot or moving components.
A
16. Repeat step 13, 14 & 15 on the other side of unit.
17. Lower seat to normal operating position.
18. Operate control levers to be sure wires, clips and
lights do not make contact with levers. If so, readjust
components so there is no interference.
Figure 6. Light Connection
A. Light
B. Harness Plug
19. Reconnect spark plug.
C. Headlight Wire Harness, w/Ribbed Plastic Cover
D. Wire Clip
E. Bracket
OPERATION
1. Start the unit using normal procedures. After the unit
has warmed up and is operating at full throttle the
lights may be turned on.
2. Turn the lights off before turning off the unit. If lights
are left on with out running the unit they will drain the
battery.
Note: The headlights may dim if the RPM’s of the engine
become to low.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Light Kit
NOTES
Form No. 1734309
Revision:00
TP 200-4583-00-AT-SN
MANUFACTURING, INC.
Briggs & Stratton Yard Power Products Group
Copyright © 2007 Briggs & Stratton Corporation
Milwaukee, WI USA. All Rights Reserved
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997 USA
4
Download from Www.Somanuals.com. All Manuals Search And Download.
|