Triple Bag Catcher
Kit No. 7600069 - 7600070
Safety Instructions
and Operator’s Manual
Instruction Manual No. 7102356 (Rev. C, 06/04/2008)
TP 200-5352-C-AT-N
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Install Bagger Mount
Install Grass Bag Support
1) Remove three bolts – two on the rear
of the tractor frame, and the top bolt on
the right rear of the tractor frame. See
Figure 1. The two rear bolts will be
replaced with longer bolts supplied in
the kit. Save the right bolt for re-
installation.
1) Align the lower U-shaped channel on the
Grass Bag Support (7500994) with the U-
shaped slot in the top of the Bagger Mount.
Insert the channel support fully into the
bagger mount. See Figure 2.
‘Hitch
Mount’
hole
Figure 2
Figure 1
2) Secure the Grass Bag Support to
the Bagger Mount with the Mounting Pin
(M720527). Hold the pin with the leg
up. Insert the Mounting pin fully into the
Bagger Mount. Rotate the mounting pin
so that the leg will be pointing down,
locking the pin in place. See Figure 3.
2) Align the holes in the Bagger Mount
Weldment (P/N 7400272A) with the
holes in the tractor frame.
3) Install
one
bolt
1/2-13x1-1/4
(7091323, not shown) into the hole in
the lower bagger mount and the tractor
frame (‘hitch mount’ hole). See Figure
1. Secure with one hex nut 1/2-13
(7091544). Do not tighten hardware at
this time.
4) Install two bolts 5/16-18x1-1/4
(1930595) into the rear of the tractor
frame. These replace the two removed
in Step 1. Secure with two flange hex
nuts 5/16-18 (1927557). Also, re-install
the right bolt into the right rear of the
tractor frame.
5) Tighten all hardware securely.
Figure 3
Instruction Manual No. 7102356 (Rev. C, 06/04/2008)
TP 200-5352-C-AT-N
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Install Grass Bags
Install Grass Bag Adapter
1) Align the slot on the hanger of the
Grass Bag Assembly (7500995) with
the tab on the grass bag support.
2) Insert the tab into the slot. Repeat
for all three grass bags. See Figure 4.
1) 46” & 52” Models Only – Attach the
Latch Pin (M720543) to the appropriate
Grass Bag Adapter, using one carriage
bolt 1/4-20x5/8 (1960252) and one
center lock flange nut 1/4-20 (1930642).
See Figure 6 (inset).
2) The Grass Bag Adapter attaches to
the deck using two bolts and two wing
nuts, provided with the kit. See Figure
6. Note – some model tractors will
already have the bolts installed in the
deck. You can use them to attach the
grass bag adapter.
Figure 4
Install Cover Assembly
1) Attach the Cover Assembly (7500996)
to the Grass Bag Support. Insert one Hinge
Pin (M720525) into each hinge, and secure
with one Hair Pin (1960074). See Figure 5.
2) Lower the cover, and pull the latch
down over the grass bag frame. The
cover must be fully closed and latched.
Grass Bag
Adapter
42” – 7501003
46” – M720560
52” – 7102377
Figure 6
3) Lift the discharge deflector. Align the
two holes in the grass bag adapter with
the holes in the deck. Note - do not
remove the discharge deflector.
4) Insert two carriage bolts 5/16-18x1-
1/4 (1960223) from inside of deck. Note
- insert forward carriage bolt first.
Secure with two wing nuts 5/16-18
(M720125). Tighten wing nuts securely.
Figure 5
Instruction Manual No. 7102356 (Rev. C, 06/04/2008)
TP 200-5352-C-AT-N
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Install Upper Elbow Tube and Middle
Grass Tube
Install Baffles on 52” Deck (Not
required on other size decks)
1) Slide the upper elbow tube
(1733885) into the cover, aligning the
ridges with the notches in the cover
opening. The opening of the elbow tube
must face towards the center of the
catcher. See Figure 7.
1) Position the left deck baffle
(7400267A) and right deck baffle
(7400268A) on the front inside surface
of the 52” deck. Align the holes and
insert carriage bolts (M720053) with the
threaded portion sticking out. Install
nuts (7090585) onto the carriage bolts.
Tighten securely. See Figure 9.
Opening of elbow
facing center of
catcher
Note – some hardware securing the
front roller and gauge wheels will have
to be removed to install the baffles.
Insert screw
(42” decks only)
Align tube
handle with
elbow ridge
Figure 7
2) Slide the clear middle tube into the
upper elbow tube. The handle on the
middle tube must be in line with the top
ridge on the elbow tube. See Figure 7.
Note: For 42” decks, align the hole in
the clear tube with the hole nearest the
elbow in the upper tube, and secure
with supplied screw. See Figure 7.
3) Slide the middle tube down over the
grass bag adapter. Pull the rubber strap
and place the hole in the strap
completely over the latch pin, securing
the middle tube to the grass bag
adapter. See Figure 8.
Figure 9
Secure strap
on tube to pin
on adapter
Figure 8
Instruction Manual No. 7102356 (Rev. C, 06/04/2008)
TP 200-5352-C-AT-N
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation and Maintenance Instructions
INTRODUCTION:
EMPTYING GRASS CATCHER
Follow operation and maintenance
instructions in the Operator’s Manual
provided with the Snapper Lawn
Tractor.
1) Empty Grass Catcher often to avoid
overfilling. Overfilling the grass bags
reduces
performance
and
causes
clogging of tube, adapter and deck.
GRASS CATCHER OPERATION
2) Turn blades off. Drive machine to
location the clippings are to be dumped.
DO NOT operate blades in reverse. If you
must back machine to dump clippings in
desired location, LOOK and SEE behind
and down for children, pets and hazards
before and while backing.
1) Select desired cutting height. Choose
a setting that will not attempt to cut off too
much at once, overloading the machine.
2) After starting engine and allowing a
brief warm up period, move engine speed
control to highest setting.
3) Drive machine to cutting area.
Engage blades.
3) Shift transmission to Neutral (N).
Engage Park Brake. Stop engine.
Remove key.
4) Unlatch and open the catcher cover.
One at a time, lift grass bag up and off of
the tab on the grass bag support.
5) After dumping, to maintain peak
performance, check the catcher screen
located on the inside of the Cover
Assembly to make sure it is clean and
free of any build up. Clean as required
with brush or broom. Reinstall all three
grass bags.
6) Close catcher. Push down firmly to
ensure the cover is fully closed and is
properly latched.
4) Select a slow forward ground speed
until familiar with conditions. Do not
select a speed that is too fast, causing
the machine to become overloaded.
5) The weight of the grass catcher and
contents will affect the stability and
handling of the machine. Avoid sudden
starts and sharp turns. Reduce speed on
slopes, and DO NOT operate machine on
slopes exceeding 10 degrees (18%
grade). Operate machine up and down
slopes. DO NOT operate machine across
the face of slopes. Turn blades off when
traveling up slope.
6) Empty grass catcher often to
minimize effect on stability and handling.
Over filling the catcher will reduce
performance and cause clogging of the
tube, adapter and deck.
7) Re-start engine and drive machine to
cutting area. Set engine speed to highest
setting, engage blades and resume
operation.
7) Do not operate the machine with the
Grass Catcher open. The entire Grass
Catcher including grass bags must be
installed, the catcher closed and latched
properly before operating.
WARNING
DO NOT operate machine without entire
grass catcher and guards in place.
GRASS CATCHER COMPONENTS are
subject to deterioration during normal
use. Inspect all components frequently for
signs of wear or deterioration. Replace
worn
or
damaged
components
immediately.
Instruction Manual No. 7102356 (Rev. C, 06/04/2008)
TP 200-5352-C-AT-N
6
Download from Www.Somanuals.com. All Manuals Search And Download.
IF THE GRASS CATCHER BECOMES
CLOGGED
GRASS CATCHER MAINTENANCE
Grass Catcher components are subject to
wear and deterioration during normal
usage. Inspect all components frequently
for signs of wear and deterioration.
Replace worn or damaged components
immediately.
The grass catcher may become plugged
if the conditions are too severe, the
catcher is overfilled, or the machine is
used improperly. If plugging does occur,
attempt the following:
BEFORE EACH USE
WARNING
1) Inspect all Catcher components.
Replace all worn or damaged parts.
2) Clean grass build-up from deck,
adapter, grass tube, covers and rear
cover screen. To maintain peak
performance make sure screen is clean
at each dumping.
DO NOT attempt to remove any clogs from
deck, adapter, or tube with engine or blade
running. STOP engine. STOP blade. Engage
parking brake. Remove key. Make sure
blade and all rotating components have
come to a complete stop before removing
or unclogging any catcher component.
3) Inspect blades for wear or damage.
Replace as needed.
1) Empty catcher more often.
2) Clean screen on Rear Cover
Assembly.
3) Ground speed too fast – cut at slower
speed.
4) Removing too much grass – raise
cutting height, cut partial width, and cut
lawn more frequently.
4) Perform pre-start check list and
maintenance as instructed in the
SNAPPER Lawn Tractor Operator’s
Manual and Engine Owner’s Manual
included with the machine.
5) Grass is too wet from rain or dew –
allow grass to dry.
6) Blades are dull or worn – inspect
blades and replace as necessary. Use
only genuine SNAPPER replacement
blades.
7) Mower equipped with incorrect blade.
Contact your local SNAPPER dealer for
assistance in choosing the correct blade
for your application.
8) Deck, adapter, or tube has clipping
build up – clean all clippings from all
internal surfaces.
Instruction Manual No. 7102356 (Rev. C, 06/04/2008)
TP 200-5352-C-AT-N
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Instruction Manual No. 7102356 (Rev. C, 06/04/2008)
TP 200-5352-C-AT-N
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Manual
Instruction Manual No. 7102356 (Rev. C, 06/04/2008)
TP 200-5352-C-AT-N
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Bagger Mount
Tractor
Frame
Existing
Hardware
1
2
Grass Bag Support
3
4
1
2
Instruction Manual No. 7102356 (Rev. C, 06/04/2008)
TP 200-5352-C-AT-N
10
Download from Www.Somanuals.com. All Manuals Search And Download.
BAGGER MOUNT
1
2
--
--
--
7400272A WELDMENT, MOUNT, GRASS CATCHER
1
2
2
1
1
1930595
1927557
7091323
7091544
BOLT – WHIZ LOCK 5/16-18 X 1-1/4
NUT – HEX FLANGE 5/16-18 WHIZ LOCK
HEX FLANGE BOLT, 1/2-13 X 1-1/4
HEX FLANGE NUT, 1/2-13
GRASS BAG SUPPORT
1
2
--
3
4
7500994
7091323
7091544
ASSEMBLY, GRASS CATCHER SUPPORT
HEX FLANGE BOLT, 1/2-13 X 1-1/4
HEX FLANGE NUT, 1/2-13
1
2
2
1
1
7300957A ARM, SUPPORT, TRIPLE GRASS CATCHER
M720527 PIN, CHANNEL MTG, GRASS CATCHER
Instruction Manual No. 7102356 (Rev. C, 06/04/2008)
TP 200-5352-C-AT-N
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Grass Bag Assembly
2
3
1
Cover Assembly
1
3
2
4
Instruction Manual No. 7102356 (Rev. C, 06/04/2008)
TP 200-5352-C-AT-N
12
Download from Www.Somanuals.com. All Manuals Search And Download.
GRASS BAG ASSEMBLY
1
2
1733695
1733517
1733709
BAG, GRASS CATCHER, CLOTH
HOOP - BAG TRIPLE
TUBE, CLIP, GRASS BAG
3
3
3
3
3
6
6
6
--
3
--
--
--
--
1703807A HANGER, GRASS BAG
1672023A CLAMP, GRASS BAG
1931333
1917356
1917372
CARRIAGE BOLT, 5/16-18 X 3/4
LOCKWASHER, SPRING 5/16
NUT - HEX 5/16-18 NC-2B
COVER ASSEMBLY
1
7500996
1733546
M720537
1960404
1933896
M720525
1960074
ASSEMBLY, COVER AND HANDLE, GRASS CATCHER
COVER ASSY - TRIPLE
HANDLE, COVER
SCREW, TRUSS HEAD PHILLIPS, #10-24 X 3/4
NUT, HEX LOCK 10C W/ NYL INSERT
PIN, COVER HINGE
1
1
1
2
2
2
2
2
4
--
--
--
--
2
3
4
--
CLIP, HAIR PIN
1733504A PIVOT, HINGE
1925003 HEX WASHER HEAD SCREW - TAPTITE 1/4-20 X 1/2
Instruction Manual No. 7102356 (Rev. C, 06/04/2008)
TP 200-5352-C-AT-N
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Grass Bag Adapter
2
3
4
6
5
1
6
Grass Tube Assembly
1
2
Instruction Manual No. 7102356 (Rev. C, 06/04/2008)
TP 200-5352-C-AT-N
14
Download from Www.Somanuals.com. All Manuals Search And Download.
GRASS BAG ADAPTER
42" BAGGER BOOT
46" BAGGER BOOT
52" BAGGER BOOT
1
1
1
2
3
4
5
--
6
M720551
M720560
7102377
M720543
1960252
1930642
1960223
7011791
M720125
1
1
1
1
1
1
2
2
2
PIN, LATCH
CARRIAGE BOLT, 1/4-20 X 5/8
NUT – CENTER LOCK FLANGE 1/4-20
CARRIAGE BOLT
BOLT RETAINER, 5/16- BLACK
NUT, 5/16-18 WINGNUT
GRASS TUBE ASSEMBLY – 42”
1
2
1733885
7500993
1734299
2171600
M720533
M720076
M720074
1928372
1930642
ELBOW - UPPER TUBE
1
1
1
1
1
1
1
2
1
ASSEMBLY, TUBE, CENTRAL
TUBE, GRASS CATCHER, CLEAR POLY
STRAP - RUBBER
HANDLE, TUBE, GRASS CATCHER
SCREW – 1/4-20 X 1
SCREW – 1/4-20 X 1/2 SLOTTED
LOCKNUT – 1/4-20 KEPS
NUT – CENTER LOCK FLANGE 1/4-20
--
--
--
--
--
--
--
GRASS TUBE ASSEMBLY – 46-52”
1
2
7501007
7500993
7102423
2171600
M720533
M720076
M720074
1928372
1930642
ELBOW - UPPER TUBE
1
1
1
1
1
1
1
2
1
ASSEMBLY, TUBE, CENTRAL
TUBE, GRASS CATCHER, CLEAR POLY
STRAP - RUBBER
HANDLE, TUBE, GRASS CATCHER
SCREW – 1/4-20 X 1
SCREW – 1/4-20 X 1/2 SLOTTED
LOCKNUT – 1/4-20 KEPS
NUT – CENTER LOCK FLANGE 1/4-20
--
--
--
--
--
--
--
Instruction Manual No. 7102356 (Rev. C, 06/04/2008)
TP 200-5352-C-AT-N
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Baffle Assembly
4
2
4
1
3
Instruction Manual No. 7102356 (Rev. C, 06/04/2008)
TP 200-5352-C-AT-N
16
Download from Www.Somanuals.com. All Manuals Search And Download.
BAFFLE ASSEMBLY
1
2
3
1
7400268A BAFFLE, RIGHT
7400267A BAFFLE, LEFT
1
1
2
5
M720053
7090585
CARRIAGE BOLT
HEX FLANGE NUT, 5/16-18
Instruction Manual No. 7102356 (Rev. C, 06/04/2008)
TP 200-5352-C-AT-N
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Instruction Manual No. 7102356 (Rev. C, 06/04/2008)
TP 200-5352-C-AT-N
18
Download from Www.Somanuals.com. All Manuals Search And Download.
|