Snapper Blower ELBX10151BV User Manual

ASSEMBLY INSTRUCTIONS

OPERATOR’S MANUAL

PARTS LIST

European

Extreme Series

Walk-Behind

Leaf Blower

Series 1

Models covered:

Actual product may differ slightly from product pictured above

ELBX10151BV

(Part # 7085912)

Manual No. 7078092 (I.R. - 09/14/04)

Download from Www.Somanuals.com. All Manuals Search And Download.

safety rules regarding outdoor power equipment

IMPORTANT! READ CAREFULLY THE FOLLOWING SAFETY RULES BEFORE

ASSEMBLING OR OPERATING UNIT.

• Operate only in the daylight or with good artificial

TRAINING

light, keeping away from holes and hidden hazards.

• Be sure of your footing while using pedestrian

controlled equipment, especially when backing up.

Walk, don’t run.

• Do not operate in reverse unless absolutely

necessary. Always look down and behind before

and while traveling in reverse.

• Be aware of the blower discharge direction and do

not point it at anyone. Do not operate the blower

without deflectors in place.

• Never leave a running unit unattended. Always

stop engine before leaving unit.

• Never operate with guards not securely in place.

Be sure all safety features are attached, adjusted

properly and functioning properly.

• Never operate with the discharge deflectors

removed or altered.

• Read, understand, and follow all instructions in the

manual and on the unit before starting. If the

operator(s) or mechanic(s) can not read English it is

the owner’s responsibility to explain this material to

them.

• Become familiar with the safe operation of the

equipment, operator controls, and safety signs.

• All operators and mechanics should be trained.

The owner is responsible for training the users.

• Only allow responsible adults, who are familiar

with the instructions, to operate the unit.

• Never let children or untrained people operate or

service the equipment. Local regulations may

restrict the age of the operator.

• The owner/user can prevent and is responsible for

accidents or injuries occurring to themselves, other

people or property.

• Do not change the engine governor setting or over

speed the engine.

PREPARATION

•

Evaluate the terrain to determine what

• Stop on level ground, shut off engine before

leaving the operator’s position for any reason.

• Stop equipment and inspect impeller blades after

striking objects or abnormal vibration occurs. Make

necessary repairs before resuming operations.

• Keep hands and feet away intake and discharge

areas.

• Keep pets and bystanders away.

• Do not operate the unit while under the influence

of alcohol or drugs.

• Use caution when crossing roads and sidewalks.

Stop engine if not blowing.

• Use care when loading or unloading the machine

into a trailer or truck.

• Use care when approaching blind corners, shrubs,

trees or other objects that may obscure vision.

accessories and attachments are needed to

properly and safely perform the job. Use only

accessories and attachments approved by the

manufacturer.

• Wear appropriate clothing including safety shoes,

safety glasses and ear protection. Long hair, loose

clothing or jewelry may get tangled in moving parts.

• Inspect the area where the equipment is to be

used and remove all objects such as rocks, toys

and wire, which can be thrown by the machine.

• Use extra care when handling gasoline and other

fuels. They are flammable and vapors are

explosive.

a) Use only an approved container.

b) Never remove fuel cap or add fuel with the

engine running. Allow engine to cool before

refueling. Do not smoke.

c) Never refuel or drain the machine indoors.

• Check that operator’s presence controls, safety

switches and shields are attached and functioning

properly. Do not operate unless they are functioning

properly.

SLOPE OPERATION

Slopes are a major factor related to loss-of-control

and tip-over accidents, which can result in severe

injury or death. All slopes require extra caution. If

you cannot back up the slope, or if you feel uneasy

on it, do not drive on it.

OPERATION

• Blow across the face of slopes; never up and

down.

• Never run an engine in an enclosed area.

• Remove obstacles such as rocks, tree limbs, etc.

Download from Www.Somanuals.com. All Manuals Search And Download.

safety rules regarding outdoor power equipment (cont.)

• Watch for holes, ruts, or bumps. Uneven terrain

could overturn the unit. Tall grass can hide

obstacles.

• Always follow the engine manual instructions for

storage preparations before storing the unit for both

short and long term periods.

• Keep all movement on the slopes slow and

gradual. Do not make sudden changes in speed or

direction.

• Always follow the engine manual instructions for

proper start-up procedures when returning the unit

to service.

• Never store the machine or fuel container inside

where there is an open flame, such as in a water

heater. Allow unit to cool before storing.

• Shut off fuel while storing or transporting. Do not

store fuel near flames or drain indoors.

• Keep all hardware, especially impeller bolt, tight

and keep all parts in good working condition.

Replace all worn or damaged decals.

• Never tamper with safety devices. Check their

proper operation regularly.

Do Not

• Do not start or stop on a slope. If tires lose

traction, proceed slowly straight down the slope.

• Do not turn on slopes unless necessary, and then,

turn slowly and gradually downhill, if possible.

•

Do not use near drop-offs, ditches, or

embankments. The operator could lose footing or

balance or blower could suddenly turn over if a

wheel is over the edge of a cliff or ditch, or if an

edge caves in.

• Clean leaves and debris from mufflers and engine

to prevent fires. Clean up oil or fuel spillage.

• Stop and inspect the equipment if you strike an

object. Repair, if necessary, before restarting.

• Never make adjustments or repairs with the

engine running unless specified otherwise.

• Park machine on level ground. Never allow

untrained personnel to service machine.

• Carefully release pressure from components with

stored energy. (e.g. springs)

• Do not operate on slopes with wet grass. Reduced

footing or traction could cause sliding.

• Do not use on excessively steep slopes.

CHILDREN

Tragic accidents can occur if the operator is not

alert to the presence of children. Children are often

attracted to the unit and its activity. Never assume

that children will remain where you last saw them.

• Keep children out of the blowing area and under

the watchful care of another responsible adult.

• Be alert and turn unit off if children enter the area.

• Before and during reverse operation, look behind

and down for small children.

• Only replace impellers. Never straighten or weld

them.

• Keep hands and feet away from moving parts.

• Frequently check components and replace with

• Never allow children to operate the unit.

• Use extra care when approaching blind corners,

shrubs, trees, or other objects that may obscure

vision.

manufacturer’s

necessary.

recommended

parts,

when

• Use only factory authorized replacement parts

when making repairs.

EMISSIONS

• Always comply with factory specifications on all

settings and adjustments.

• Engine exhaust from this product contains

chemicals known, in certain quantities, to cause

cancer, birth defects, or other reproductive harm.

• Look for the relevant Emissions Durability Period

and Air Index information on the engine emissions

label.

• Only authorized service locations should be

utilized for major service and repair requirements.

• Never attempt to make major repairs on this unit

unless you have been properly trained. Improper

service procedures can result in hazardous

operation, equipment damage and voiding of

manufacturer’s warranty.

MAINTENANCE AND STORAGE

• Always observe safe refueling and fuel handling

practices

when

refueling

the

unit

after

transportation or storage.

Download from Www.Somanuals.com. All Manuals Search And Download.

unit assembly

Note: Please refer to Parts List for correct part identification and placement.

FRONT WHEEL ASSEMBLY

•

Place Mounting Bracket against lower right

corner of Blower Housing, aligning holes in

bracket with threaded studs in housing. Secure

with three 3/8-16 hex nuts, split lock washers

and flat washers. Tighten securely.

Install Front Wheel between forks in bracket

and secure with 5/8-11 x 5” hex bolt and lock

nut. Tighten snugly while allowing for free

rotation of wheel.

HANDLE ASSEMBLY

•

The upper handles are shipped in the folded

storage position. To unfold, loosen two handle

knobs and rotate up to the operating position.

The upper handles are secured with four knobs.

Insert two 5/16-18 x 2 curved head bolts

through the handles directly below the two

shipping knobs. Place one internal tooth lock

washer on each of the bolts. Thread knobs onto

curved head bolts. Tighten all four knobs

securely.

Assembly complete. Your unit is now ready to be started and checked for proper operation.

Some minor final adjustments may be required; see the Maintenance portion of this manual.

Download from Www.Somanuals.com. All Manuals Search And Download.

unit operation

STARTING THE ENGINE

IMPORTANT NOTE: The procedures outlined within this section are general guidelines, and are in no way

meant to replace or supercede engine manufacturer’s operating instructions. In order to obtain optimum

performance from your engine, refer to your engine manual.

WARNING! IMPELLER IS MOUNTED DIRECTLY TO ENGINE SHAFT –

STARTING ENGINE WILL RESULT IN IMMEDIATE HIGH-VELOCITY

DISCHARGE. TO AVOID INJURY OR DAMAGE, BE SURE DISCHARGE IS

POINTED AWAY FROM PEOPLE, PETS AND PROPERTY WHEN STARTING.

BEFORE STARTING ENGINE:

•

Be sure that the unit is completely assembled, all fasteners are tightened securely, and all safety guards

and components are in place.

•

Be sure to check engine’s oil and fuel levels* and add as needed. (See engine manual for recommended

oil and gasoline specifications.) Never check the engine while it is running or while you are smoking.

Check only when engine is cold.

All machines are shipped without oil or fuel unless otherwise noted.

Be sure that fuel valve is set to open position.

•

OPEN

CLOSED

TO START ENGINE:

•

Move choke control located on engine to the

closed “ON” position.

CHOKED

•

Move engine speed control, located on the

handle, to the fast “Rabbit” position.

ENGINE

SPEED

CONTROL

Download from Www.Somanuals.com. All Manuals Search And Download.

unit operation (cont.)

STARTING THE ENGINE (cont.)

•

Bracing unit with one hand on the upper handle

and a foot on the right rear tire, firmly grasp

recoil handle and pull briskly. You may have to

pull several times before engine starts. (If

engine fails to start within a reasonable amount

of time, discontinue and check engine manual

for further instructions.) Note: Do not allow

recoil rope to snap back into recoil; damage to

the rope or recoil could result.

RECOIL HANDLE

PULL

BRISKLY

•

After engine starts, move engine speed control

to approximately half and return choke control

to open “OFF” position.

TO SHUT ENGINE DOWN:

•

Move engine speed control to slow “Turtle” position.

Allow engine to idle for 2-3 minutes before shutting down.

Move engine speed control to “STOP” position. Turn fuel valve to closed position.

IMPORTANT NOTE: If you experience problems with your engine that cannot be satisfactorily resolved by following the

instructions contained within the engine manual, contact your local engine dealer, or call the toll-free service number listed in

the repair section of the engine manual. All engine service, warranty or otherwise, is required to be performed by a

manufacturer-authorized service center. The equipment manufacturer is neither authorized nor responsible for any type of

warranty engine service, nor is it equipped to perform any such service.

BLOWER OPERATION

DANGER! DO NOT PASS BY OR STAND ON THE AIR DISCHARGE SIDE OF ANY

LEAF BLOWER WITH THE ENGINE RUNNING. HIGH VELOCITY DISCHARGE CAN

EASILY TURN HARMLESS DEBRIS INTO FLYING PROJECTILES.

DANGER! NEVER INSERT ANY BODY PART OR FOREIGN OBJECT INTO ANY

OPENING WHILE UNIT IS RUNNING. SERIOUS INJURY OR DEATH CAN RESULT.

Download from Www.Somanuals.com. All Manuals Search And Download.

unit operation (cont.)

GENERAL RULES TO OBSERVE BEFORE

AND DURING OPERATION:

•

Inspect your unit before each and every use. Check for worn, bent or broken components, loose fasteners, low or flat

tires, etc., and repair or replace prior to operation. DO NOT OPERATE A MACHINE THAT IS WORN OR

DAMAGED – SERIOUS INJURY OR DEATH CAN RESULT.

•

Clear the entire work area of all debris that could cause damage to or become entangled in the unit. Rocks and large

branches can wedge themselves between the impeller and housing, causing equipment damage or personal injury. If

in doubt, remove it.

•

Do not start unit until you are ready to begin blowing, and promptly shut off unit as soon as operation is complete.

Keep hands, feet and clothing away from rotating parts. Never place your feet or hands in path of discharge.

Use proper discretion in selecting your debris removal pattern, especially on uneven terrain. Avoid steep hills,

especially if surface is wet. Do not travel straight down slopes exceeding 14 degrees. If tires begin to slip when

climbing a slope, the grade is too steep for safe operation. Angle the unit to a less steep slope until tires stop slipping

and traction is regained.

•

Be keenly aware of your surroundings while operating unit – children and pets can pop out of nowhere.

Learn to listen to your machine – being aware of what a well-running unit sounds like can alert you to a potential

problem. A straining engine or clanging impeller means that trouble is almost sure to follow.

TO CHANGE AIR DISCHARGE DIRECTION:

•

To direct air discharge out from the front of the

machine, open the forward air deflector door,

mounted on the front of the discharge end of

the blower, by pushing the control lever to the

front of the machine. This feature is ideal for

such things as blowing debris from a wall or

fence. Adjust engine speed to increase or

decrease air discharge rate.

FRONT

SIDE

•

To direct air discharge out from the side of the

machine, close the forward air deflector door by

pulling the control lever toward the back of the

machine. Adjust the discharge deflector up or

down to control angle of discharge. This feature

is ideal for such things as blowing debris into

neat rows. Adjust engine speed to increase or

decrease air discharge rate. IMPORTANT:

SHUT UNIT DOWN BEFORE ADJUSTING

SIDE DEFLECTOR.

ADJUST

Download from Www.Somanuals.com. All Manuals Search And Download.

unit operation (cont.)

HINTS FOR EFFECTIVE OPERATION:

•

For operator ease and maneuverability, push down on the upper handle while walking so that the machine

balances on the rear wheels.

•

When blowing dry debris, set blower discharge to lower rate; when blowing wet or frozen debris, increase

discharge rate.

maintenance

BEFORE MAKING ANY ADJUSTMENTS, STOP ENGINE AND DISCONNECT SPARK

PLUG WIRE TO PREVENT INADVERTENT STARTING OF UNIT.

GENERAL:

•

Follow implicitly the engine manufacturer’s recommendations for maintenance.

Always keep your machine clean – especially the engine. Check all adjustments periodically. Also,

periodically check that all fasteners are secure.

•

Never make any adjustments to the unit until the engine is off and the spark plug wire is disconnected.

If carburetor adjustment is necessary, stand to one side and keep feet and hands in the clear while making

adjustments.

•

Keep engine free of accumulations of grass, leaves or excessive grease. An accumulation of these

combustible materials may result in a fire.

•

Store gasoline in a safe and approved container in a cool, dry place.

Keep the unit and any fuel containers in locked storage to prevent children from playing and/or tampering

with them.

•

Do not store gasoline powered equipment or fuel containers in a basement or any closed area where

heating or heat appliances or open pilot lights are present, unless the fuel is completely drained from the

power equipment and the fuel containers.

LUBRICATION:

•

The tires on your blower contain bearings that should be lubricated on a weekly basis using a high-

performance, automotive quality grease to ensure long life and minimal wear.

Download from Www.Somanuals.com. All Manuals Search And Download.

maintenance (cont.)

BEFORE MAKING ANY ADJUSTMENTS, STOP ENGINE AND DISCONNECT SPARK

PLUG WIRE TO PREVENT INADVERTENT STARTING OF UNIT.

TROUBLESHOOTING:

•

UNIT WILL NOT START:

•

Check fuel and oil levels.

Check to make sure choke is set when engine is cold, off when hot.

Check throttle for proper operation.

Check intake baffle for jammed debris or accumulation of debris.

If condition persists, contact dealer.

•

UNIT STALLS:

•

Check fuel and oil levels.

Check intake baffle for jammed debris or accumulation of debris.

If condition persists, contact dealer.

EXCESSIVE NOISE OR VIBRATION:

•

Check to make sure all fasteners are tightened securely.

Remove intake baffle and visually inspect impeller for broken, bent, or cracked blades; also make sure

impeller hub is securely tightened onto engine shaft – bolt should be torqued to 15 ft/lbs. Pull recoil and

check for bent engine shaft. Contact dealer for repair or replacement if necessary. Do not attempt to

repair a damaged impeller or bent engine shaft. Serious injury or equipment damage may result.

BEFORE REMOVING INTAKE BAFFLE, OR ANY OTHER COMPONENT, STOP ENGINE AND

DISCONNECT SPARK PLUG WIRE TO PREVENT INADVERTENT STARTING OF UNIT.

•

UNIT DOES NOT TRAVEL STRAIGHT:

•

Check camber on front wheel, adjust as needed. See Front Wheel Camber Adjustment.

Make sure wheels are lubricated – see Lubrication.

Download from Www.Somanuals.com. All Manuals Search And Download.

maintenance (cont.)

ADJUSTMENTS:

BEFORE MAKING ANY ADJUSTMENTS, STOP ENGINE AND DISCONNECT SPARK

PLUG WIRE TO PREVENT INADVERTENT STARTING OF UNIT.

•

THROTTLE CABLE ADJUSTMENT: Correct

LOOSEN SCREW

cable adjustment allows for full range of

movement of throttle body on engine in

conjunction with throttle control on handle. To

adjust, loosen cable clip screw on engine, then

slide cable housing in or out in approximately

1/8-1/4” increments. Retighten screw, recheck,

and readjust as needed.

MOVE CABLE

•

FRONT WHEEL CAMBER ADJUSTMENT:

Correct camber adjustment will place the front

axle at 0 degrees, or parallel with level ground,

and the wheel at 90 degrees or perpendicular

with level ground. Adjust by loosening the

three mounting bolts and placing a square

aside the wheel and adjusting until square sits

flat on ground and touches upper and lower

points of tire, then retightening bolts. An

alternate method is to place a level against the

side of the caster bracket.

90°

0°

REPLACEMENT PARTS:

•

Replacement parts are available through your dealer.

Download from Www.Somanuals.com. All Manuals Search And Download.

illustrated parts list

ELBX10151BV

Download from Www.Somanuals.com. All Manuals Search And Download.

illustrated parts list (cont’d)

Item

Part No.

3010267

-----

Qty

---

Description

WELDMENT, Housing- Extreme Blower, LBX10151BV

DECAL – See DECAL IDENTIFICATION

ENGINE, B&S 10HP Intek OHV

3039111

Briggs Model 205412 Type 0121-E1

SCREW, 5/16-18 x 1-1/2 Hex Head Cap, GR5

NUT, 5/16-18 Hex Flange Lock, GR5

DECAL – See DECAL IDENTIFICATION

SCREW, 5/16-24 x 1-3/4" Hex Head Cap, GR5

SCREW, 5/16-18 x 1-1/4", Hex Head Cap, GR5

KEY, 1/4" Square x 1-7/16"

KNOB, Fluted- Folding Handles

ASSEMBLY, 15" 9 Blade Impeller (Includes items 11A, 11B & 3 ea

items 8 & 37)

91540

91601

-----

91513

91527

12315

3071776

3021599

---

11A

11B

3021595

3021597

3020233

91511

3024500

91523

IMPELLER, Cast, 15" O.D.

HUB, Taper-Lok, Type 1 - P1 x 1.125 (1.938 OAL)

WELDMENT, Intake Baffle- Extreme

NUT, 5/16-18 Hex, GR5 or B

DEFLECTOR, Side Air

SCREW, 5/16-18 x 5/8" Hex Washer Self-Tap

GUIDE, Rope (1/4-20 thread)

WELDMENT, Door Front/Side Discharge

BUSHING, Steel Sleeve .250 ID x .375 OD x .25 Long

WASHER, 1/4" Split Lock

SCREW, 1/4-20 x 3/4" Hex Head Cap, GR5

SPRING, Extension- Side Air Discharge Door

KNOB, Ball Hand Lever- 3/8-16 Metal Insert

TUBE, Front Wheel- Extreme

NUT, 1/4-20 Hex Center Lock, GR5 or B

ASSY., Wheel & Tire 410/350-4 "Flatfree"

BALL BEARING, 5/8 x 1-3/8" (include with wheel assembly, item 25)

WASHER, .64 x .99 x .05 Flat

RING, External Retaining (TRU1500-62)

BRACKET, Front Wheel Mounting

NUT, 3/8-16 Hex, GR5 or B

46465

3024501

3031014

27223

91495

3071782

3031103

3034053

90372

3033276

3033107

91628

12763

3033186

91302

91320

90517

3033300

91822

91894

33753

3032160

91315

1717312

33866

3023276

74422

WASHER, 3/8" Split Lock

WASHER, 3/8" Flat

ASSY., Tire & Wheel 9 x 350-4 "Flatfree"

BOLT, 1/2-13 x 5" Hex Head Cap

NUT, 1/2-13 Hex Center Lock, GR5

HANDLE, Lower Folding- Wide- Blower

MOUNT, Vibration

WASHER, 5/16" Split Lock

WASHER, 5/16" Curved

DASH PANEL, Blower- Wide

ASSY, Upper Handle & Grip- Wide (p/n 33696 + grip)

GRIP, 1.0 x 21-1/2" Foam

91189

BOLT, 5/16-18 x 2", Curved Head Square Neck, GR2

Download from Www.Somanuals.com. All Manuals Search And Download.

illustrated parts list (cont’d)

Item

Part No.

90391

3071800

3031220

90505

90188

76978

91298

-----

Qty

---

Description

WASHER, 5/16" Internal Tooth Lock

THROTTLE CONTROL, Briggs

BUSHING, Flanged .375 x .500 x .25 (.625 x .063 Flange)

SCREW, 1/4-20 x 2" Hex Head Cap, GR5

WASHER, .34 x .69 x .08 Flat

NUT,1/4-20 Hex Nyloc

NUT, 5/16-18 Hex Nyloc

DECAL – See DECAL IDENTIFICATION

Download from Www.Somanuals.com. All Manuals Search And Download.

decal identification

75893 – EAR/NOSE/BREATHING

PROTECTION REQUIRED – LOCATED

ON SIDE OF BLOWER HOUSING

29776 – EUROPEAN CERTIFICATION –

LOCATED ON REAR OF BLOWER HOUSING

75892 – DANGER – FLYING MATERIAL –

LOCATED ON SIDE OF BLOWER HOUSING

22841 – DANGER – KEEP HANDS AND FEET AWAY –

LOCATED ABOVE BLOWER DISCHARGE

29490 – MODEL YEAR 2004 – LOCATED

ON REAR OF BLOWER HOUSING

78069 – NOISE RATING – LOCATED ON

REAR OF BLOWER HOUSING

Download from Www.Somanuals.com. All Manuals Search And Download.

decal identification (cont’d)

75760 – SNAPPER LOGO – LOCATED ON INTAKE

BAFFLE (ON APPLICABLE MODELS)

73462 – WARNING COMBO – LOCATED

ON TOP OF BLOWER HOUSING

75861 / 29445 – GIANT-VAC LOGO – LOCATED ON

MID-HANDLE PANEL (ON APPLICABLE MODELS)

3079269 – ‘EASY-OFF IMPELLER’ –

LOCATED ON INTAKE BAFFLE

1722551 – SIMPLICITY LOGO – LOCATED ON

INTAKE BAFFLE AND MID-HANDLE PANEL (ON

APPLICABLE MODELS)

3079268 – ‘NO FLAT TIRES’ –

LOCATED ON INTAKE BAFFLE

EUROPEAN PERFORMANCE:

Maximum level of vibration measured at

the operators hand 16 m/sec2

3046585 – GIANT-VAC EXTREME LOGO – LOCATED ON

INTAKE BAFFLE (ON APPLICABLE MODELS)

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

______________________________________________________________________

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

______________________________________________________________________

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

______________________________________________________________________

Download from Www.Somanuals.com. All Manuals Search And Download.

European

Extreme Series

Walk-Behind

Leaf Blower

Series 1

McDonough, GA 30253 USA

Manual No. 7078092 (I.R. - 09/14/04)

Download from Www.Somanuals.com. All Manuals Search And Download.

Sennheiser Microphone 20230 User Manual
Silvercrest CD Player KH 2278 User Manual
Snapper Blower SLBC55151BV User Manual
Sony Cassette Player TCM 473V454VK435V User Manual
Sony Cell Phone W700i User Manual
Sony Clock Radio 3 873 060 341 User Manual
Sony Speaker F1734 User Manual
Sony Stereo Receiver STR DG300 User Manual
Sungale Digital Photo Frame CA700 User Manual
Suzuki Boat DF250SS User Manual