OWNER’S MANUAL
SMT9.2HR SMT9.2HRAB
Model Name SMT9.2HR/SMT9.2HRAB
Serial Number
Purchase Date
Write down for future reference.
treadmillbynet.com
Smoothfitness.com
-
SALES: (888) 559-8810
SERVICE: (888) 340-0482
Smooth Fitness
Part# 15-0128
Mt. Laurel, NJ
Download from Www.Somanuals.com. All Manuals Search And Download.
Model Specification Sheet
MODEL
SMT9.2HR
SMT9.2HRAB
Horsepower
Continuous
Console Display
3.0HP
Five Multi-function LED
3.0HP
Five Multi Function LED
Windows, With green-
Pace function
6
Windows, With green
Pace function
Pre-set Programs
Custom Programs
User Defined Programs
Heart Rate Interactive
Incline Range
6
10
2
10
2
Yes
Yes
0 to 15%
.6 to 10 MPH
2-Ply
0 to 15%
.6 to 10 MPH
Aero-Belt 2 Ply
Speed Range
Belt Type
Belt Size
(Width x Length) in inches
Residential Motor
Warranty
Residential Parts
Warranty
Residential Frame
Warranty
Residential Labor
Warranty
20” x 56.5”
10 Years
3 Years
Lifetime
1 Year
20” x 56.5”
10 Years
3 Years
Lifetime
1 Year
Light Institutional
Warranty
1 Year Motor, Parts, Frame, & Labor
1 Year Motor, Parts, Frame, & Labor
Width x Length in inches
User Weight
30” X 70”
400 lbs.
Lifetime
30” X 70”
400 lbs.
Lifetime
Warranty Frame
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Information
WARNING! Before using this treadmill or starting any exercise program, consult your physi-
cian. This is especially important for persons over the age of 35 and/or persons with pre-
existing health problems. The manufacturer or distributor assumes no responsibility for
personal injury or property damage sustained by or through the use of this product.
WARNING! To reduce the risk of electrical shock, burns, fire, or other possible injuries to the
user, it is important to review this manual and the following precautions before operation.
SAFETY PRECAUTIONS AND TIPS
z It is the owner’s responsibility to ensure that all users of this treadmill have read the
Owner’s Manual and are familiar with warnings and safety precautions.
z The treadmills have a user maximum capacity of 400 pounds.
z The treadmill should only be used on a level surface and is intended for indoor use only.
The treadmill should not be placed in a garage, patio, or near water and should never be
used while you are wet. SMOOTH recommends a treadmill mat be placed under the tread-
mill to protect floor or carpet and for easier cleaning.
z Follow safety information in regards to plugging in your treadmill. Keep the power cord
away from the incline wheels and do not run the power cord underneath your treadmill. Do
not operate the treadmill with a damaged or frayed power cord.
z Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not
use the treadmill with bare feet, sandals, socks or stockings.
z Always straddle the belt and allow it to start moving before stepping onto the belt.
z Hold on to handrails when adjusting speed, incline, or other controls.
z Always examine your treadmill before using to ensure all parts are in working order.
z Allow the belt to fully stop before dismounting.
z Pets should never be allowed near or on the treadmill.
z Do not leave children unsupervised near or on the treadmill.
z Never operate the treadmill where oxygen is being administered, or where aerosol prod-
ucts are being used.
z Never insert any object or body parts into any opening.
z For safety and to prevent damage to your treadmill, no more than one person should use
the treadmill at a time.
z Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill
should only be performed by an authorized service representative, unless authorized
and/or instructed by the manufacturer
z Failure to follow these instructions will void the treadmill warranty.
z Never leave the treadmill unattended while it is running
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start
Thank you for purchasing the SMOOTH treadmill! This quality product you have chosen
was designed to meet your needs for cardiovascular exercise.
z Before you start, please read the Owner's Manual and become familiar with the oper-
ation of your new treadmill.
z Remember to take the time to perform the stretching exercises provided to
avoid injury.
z Do not stand on the walking belt while pressing the Power button or Start/Stop button.
z Always adjust the speed of the treadmill in small increments as this treadmill is capa-
ble of high speeds.
z If you are taking medication, consult your physician to see if the medication will affect
your exercise heart rate.
z If you have heart problems, you are not active, and/or are over the age of 35 years,
do not use the pre-set treadmill programs or start an exercise program without first
contacting and receiving approval from your physician.
z To avoid the risk of electrical shock, always keep the console dry. Do not spill liquids
on the console. SMOOTH recommends a sealed water bottle for beverages con-
sumed while using the treadmill.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Warm Up Exercises
EXERCISE GUIDELINES
WARNING! Before beginning this or any exercise program, you should consult your physician. This
is especially important for individuals over the age of 35 or individuals with pre-existing health prob-
lems.
Warming up prepares the body for the exercise by increasing circulation, supplying more oxygen to
the muscles and raising body temperature. Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. The photos on this page show several forms of basic stretching you
may perform before your workouts. In order to achieve an adequate warm-up, perform each stretch
three times.
TOE TOUCH STRETCH
Stand bending your knees slightly and slowly bend forward from your hips.
Allow your back and shoulders to relax as you reach down toward your
toes as far as possible. Hold for 15 counts, then relax. This will stretch your
hamstrings, back of knees, and back.
HAMSTRING STRETCH
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your
extended leg. Reach toward your toes as far as possible.
Hold for 15 counts, then relax. This will stretch your ham-
strings, lower back, and groin.
CALF/ACHILLES STRETCH
With one leg in front of the other, reach forward and place your hands against
a wall. Keep your back leg straight and your back foot flat on the floor. Bend
your front leg, lean forward and move your hips toward the wall. Hold for 15
counts, then relax. To cause further stretching of the Achilles tendon, bend
your back leg as well. This will stretch your calves, Achilles tendons, and
ankles.
QUADRICEPS STRETCH
With one hand against a wall for balance, reach back and grasp one foot
with your other hand. Bring your heel as close to your buttocks as possi-
ble. Hold for 15 counts, then relax. This will stretch your quadriceps and
hip muscles.
INNER THIGH STRETCH
Sit with the soles of your feet together and your knees outward. Pull
your feet toward your groin area as far as possible. Hold for 15
counts, then relax. This will stretch your quadriceps and hip muscles.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
Minor Assembly Required!
The Smooth 9.2HR and HRAB treadmill is shipped in two pieces: the console upright assembly,
and the base assembly. After opening the box, remove any packing materials from the treadmill. Do
not throw away any packing materials until the unit is working properly. The treadmill box contains a
package that includes the Owners Manual, a RED SAFETY KEY, and a belt adjustment tool. The
treadmill will not operate without the Red Safety Key.
The console upright assembly is attached to the base assembly. Place the unit on a clean, level
surface near an electrical outlet (extension cords are not recommended).
See Figure 1
1. Raise the console into an upright position. Loosely install both 3/4” buttonhead screws on
each side of the upright. Install and tighten each 3 1/2” x 5/16” bolt (2) with washers from the
bottom of the base frame through the upright lock (diag. 1).
2. Now tighten the buttonhead screws securely from step 1.
3. Install motor hood cover using 5/8” phillips head screws (8 screws).
Be sure the treadmill is level to the floor. The rear feet can be adjusted to level the treadmill.
Assembly is now complete!
Figure 1
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Requirements
IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN
RESULT IN A RISK OF AN ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELEC-
TRICIAN OR SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE PROD-
UCT IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE
PRODUCT IF IT WILL NOT FIT THE OUTLET. HAVE A PROPER OUTLET INSTALLED
BY A QUALIFIED ELECTRICIAN.
This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical
power. Voltage spikes, surges, and noise interference can result from weather conditions or from
other appliances being turned on or off. To reduce the possibility of treadmill damage, always use a
surge protector (not included) with your treadmill.
Surge protectors can be purchased at most hardware stores. The manufacturer recommends a sin-
gle outlet surge protector with UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with
UL suppressed voltage rating of 400V or less and an electrical rating of 120VAC, 15 amps.
This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of
least resistance for electric current should the treadmill malfunction. This treadmill comes with an
electrical cord with an equipment-grounding conductor and a grounding plug. Always plug the
power cord into a surge protector, and plug the surge protector into an appropriate outlet that is
properly installed and grounded in accordance with all local codes and ordinances.
This product is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug
illustrated in the drawing below.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Console Functions and Descriptions
There are five LED display windows on the control panel to provide you with vital feedback information.
TIME WINDOW
z
z
TIME: Indicates elapsed time after pressing start in minutes and seconds (0-99 minutes, 0-59 seconds)
PACE: Indicates number of minutes to complete 1 mile at current speed.
SPEED WINDOW
z
SPEED: Indicates MPH (miles per hour) or Km/H (kilometer per hour) in .1 increments
DISTANCE / CALORIES WINDOW
z
z
DISTANCE: Indicates Miles or Kilometers traveled in .01 increments up to 9.99 and .1 increments starting at 10.0
CALORIES: Indicates estimated calories used based on 150 lb. person at the indicated speed, incline, and time
INCLINE WINDOW
z
z
z
INCLINE: Indicates incline in percent of grade 0-15% in 1% increments.
PULSE Indicates current heart rate
HEART “<”: Indicates control panel is receiving a signal from heart rate transmitter. Heart will blink on and off if
receiving signal from Heart Rate Transmitter chest strap.
CENTER BRICKYARD
z
Displays quarter mile track in Manual mode. Indicates position on track by a blink. In program mode, shows the
change in speed profile across the interval range (1-10) and shows position with a blinking action.
SPEED BAR
z
The Speed Bar allows the user to adjust speed quickly. The Speed Bar works in all manual and program modes.
To use the Speed Bar, the belt must already be moving. Press the desired speed (2 through 8), and the treadmill will
slowly reach the speed selected. In program mode, the change in speed with the Speed Bar will only work in the cur-
rent interval. Once the program switches to another interval, the speed will revert to the programmed speed.
INCLINE BAR
z
The Incline Bar allows the user to adjust Incline quickly. The Incline Bar works in all manual and program modes.
To use the Incline Bar, the belt must already be moving. Press the desired Incline (2 through 8), and the treadmill will
slowly reach the Incline selected. In program mode, the change in incline with the Incline Bar will only work in the cur-
rent interval. Once the program switches to another interval, the incline will revert to the programmed speed.
TOGGLE SWITCHES IN HANDLEBARS FOR SPEED AND INCLINE
Your treadmill is equipped with toggle switches that conveniently change the incline and speed without reaching up to
the console. In program mode, the change in speed and/or incline with the toggle switches will only work in the current
interval. Once the program switches to another interval, the speed and incline will revert to the programmed speed and
incline.
LED INDICATORS - (small green diode lights on console)
z
PROGRAM SELECTION: The treadmill console will display the program selected with a LED light beside the pro-
gram., showing on the left hand side of the window.
TIME: LED indicators will toggle back and forth for the Pace and the Workout Time. The Pace will be indicated while
z
in a program. The PACE is the number of minutes it would take to complete one (1) mile at the current speed of the
treadmill. The WORKOUT TIME is the total time set at the beginning of a program, and will count down from the amount
of time set throughout the program, or will count up in Manual mode.
z
CALORIES & DISTANCE: LED indicators will toggle back and forth to show total Calories burned and total Distance
covered. The Calories burned is an estimate based on a 150 lb person at the current speed and incline levels.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Console Layout
SMT9.2HR and SMT9.2HRAB
IMPORTANT! Please note that the Console Overlay used on the SMT9.2HRAB will read SMT9.2HR.
The only difference in the two models is the type of walking belt used. The SMT9.2HRAB uses a
thick, orthopedic-style belt. To verify the model you have received, review the SERIAL NUMBER
LABEL located on the console upright. The Serial Number Label will indicate the actual model num-
ber.
Heart Rate Controls
Program Controls
Power
Start/Stop
Pause
Enter
One-Touch/Incline Buttons
One-Touch/Speed Buttons
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Program and Operating Instructions
QUICK START / MANUAL MODE
z Plug into a standard wall outlet (110-Volt AC, 15-amp circuit).
z Stand on the treadmill and straddle belt.
z Press POWER button. There will be an eight (8) second delay after pressing the POWER button
before data can be entered. The TIME window will flash.
z Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the
belt starts moving. Speed or incline may be adjusted by using the appropriate + (increase) or –
(decrease) buttons.
z To end your workout, press START/STOP button. Belt will gradually slow to zero.
z To pause your workout, press PAUSE.
z To re-start after pausing: Press the PAUSE button. WARNING: The treadmill belt will resume
at the speed the treadmill was moving before pausing.
z Countdown Time, Preset Speed and/or Incline: Time, Speed, and Incline may be preset prior
to getting started. After pressing the POWER button, the time window will blink. Use the
SPEED/TIME + or – arrows to select your workout time, then press the ENTER PROGRAM but-
ton. The SPEED/TIME window will now be flashing. Using the same + or – arrows, select the
speed for your workout, then press ENTER PROGRAM. Now the INCLINE window will be flash-
ing. Use the INCLINE + or – arrows to set your workout incline, then press ENTER PROGRAM.
To start, press the START/STOP button.
PROGRAM MODE
z Plug into a standard wall outlet (110-Volt AC, 15-amp circuit).
z Stand on the treadmill and straddle belt.
z Press POWER button. There will be an eight (8) second delay after pressing the POWER button
before data can be entered. The TIME window will flash.
z There are six (6) pre-set programs in the 9.2HR and 9.2HRAB. The programs includes Rolling
Hills, Speed Intervals, Plateau, Weight Loss Heart-rate, and User Programs. Select the program
by pressing the appropriate button. An “OP” (meaning Original Program) will appear in the DIS-
TANCE/CALORIES window.
z Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the
belt starts.
Pre-Set Program Descriptions
Rolling Hills Program
The Rolling Hills Program is designed to vary treadmill elevation while maintaining a constant walk-
ing belt speed.
Speed Intervals Program
The Speed Intervals Program is designed to vary treadmill speed while maintaining a constant ele-
vation.
Plateau Program
The Plateau Program is designed to gradually increase treadmill Speed and elevation in the first
segment (warm up), and gradually decrease speed and elevation in the last segment (cool down).
Weight Loss Program
The Weight Loss Program is designed to alternate between the programmed speed and incline.
The program will alternate between: 1) the full programmed incline and half the programmed speed,
to 2) zero incline and the maximum programmed speed.
User Program
The User Program is a personal program that the user sets, it allows the user to customize the
speed and incline for each of the (10) ten intervals.
Heart Rate Program
The Heart Rate program is designed to keep your heart rate a desired level of “beats per minute” by
automatically adjusting the incline.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Program and Operating Instructions
PROGRAM MODE continued
Customizing Pre-Set Programs
z Customizing programs in P1 and P2 Mode: Each pre-set program can be customized in
the P1 or P2 mode. After making the program selection, the top right window (CALO-
RIES / DISTANCE) will read “OP.” ”OP” refers to “original program” and is preset. Press
the same program button once more, and the CALORIE / DISTANCE window will read
P1. The “P1” mode is now accessed. You can now program the Time, Speed, and
Incline in P1 mode, which will save your entered information for future use. The time win-
dow will blink. Use the SPEED/TIME + or – buttons to select your workout time, then
press the ENTER PROGRAM button. The SPEED/TIME window will now be flashing.
Using the SPEED/TIME + or – buttons, select the speed for your workout, then press
ENTER PROGRAM. Now the INCLINE window will be flashing. Use the INCLINE + or –
buttons to set your workout incline, then press ENTER PROGRAM. To start, press the
START/STOP button. To access P2 mode, press the selected program button three
times (once for OP, twice for P1, three times for P2). Follow the above procedure to cus-
tomize.
z
TO CHANGE A PREVIOUSLY PROGRAMMED CUSTOM PROGRAM P1 or P2:
Once you have programmed the P1 or P2 modes, you will need to use the PAUSE but-
ton to change the program you previously entered. For instance, if P1 in Rolling Hills has
been programmed, to change to a new setting, press the Rolling Hills button twice to
access P1. Then press the PAUSE button to get the TIME window to flash. Follow the
directions above to continue to change the program.
Customizing User Defined Programs
z User programs allow you to customize each of the 10 program segments. Press the
User program button once for User Program 1 (U1), or press the User program button
once more for User Program 2 (U2). The time window will flash. U1 or U2 will appear in
the DISTANCE window. Set your workout time. Notice the first segment light flashing in
the center brickyard. Now the SPEED window will flash, set your speed for the first seg-
ment using the SPEED/TIME + or – buttons, and press ENTER PROGRAM button to
set. Now the INCLINE window will flash. Set the desired incline using the Incline + or -
buttons, and press ENTER PROGRAM button to set. At this point, look at the center
brickyard and notice the second segment light is now flashing. Repeat steps above to
program all ten segments.
z
TO CHANGE A PREVIOUSLY PROGRAMMED USER PROGRAM U1 or U2:
Once you have programmed the U1 or U2 modes, you will need to use the PAUSE but-
ton to change the program you previously entered. For instance, if U1 (User Program 1)
has been programmed, to change to a new setting, press the USER PROGRAM button
once to access U1. Then press the PAUSE button to get the TIME window to flash.
Follow the directions above to continue to change the program.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Program and Operating Instructions
See page 14 for pictures and diagrams
HEART RATE MONITOR MODE
The treadmill may at any time be used in the Heart Rate Monitor Mode. If the signal from the chest
strap is detected, heart rate BPM will be displayed in the INCLINE window. The incline will only be
briefly displayed if manual or program changes are initiated. The Heart Rate program is designed to
keep your heart at a desired amount of “beats per minute” by automatically adjusting the incline. For
example, you have programmed in a desired heart rate of 125 BPM and your heart rate is only at
110 BPM. If you are wearing the Heart Rate Transmitter correctly, the incline will automatically
increase to intensify the work load, causing your heart rate to slowly climb to 125 BPM. The tread-
mill will attempt to maintain your target heart rate through adjustments to the incline for the remain-
der of your workout. In the same respect, if your heart rate is above your programmed amount of
BPM’s, the incline will automatically decrease to lower your heart rate. You may at any time during
the Heart Rate Program adjust/override the speed and/or the incline by simply pressing the correct
corresponding button. You may also change your “Target Heart Rate” at any time by pressing the
TARGET UP or TARGET DOWN button.
HEART RATE PROGRAM OPERATION
z Plug treadmill into a surge protector outlet. Attach the Red Safety Key on to the treadmill
console.
z Stand on the treadmill and straddle belt. Attach safety key clip to your clothes.
z Press POWER button. Place the Heart Rate Transmitter strap across your chest and connect
ends. (Make sure your skin is moist and the strap is snug for accurate transmission). At this time,
if the display is receiving a signal from the chest strap, the incline window will begin to settle on
your current heart rate.
z Press the HEART RATE CONTROL button to enter the electronics into the Heart Rate Program.
The incline window will momentarily flash ‘125’, which is the default program target heart rate.
z The WORKOUT TIME window will blink. Use the SPEED + or – arrows to select your workout
time. Press ENTER PROGRAM.
z The SPEED window will then blink. Use the same + or – arrows to select the speed for your
workout. Press ENTER PROGRAM.
z The incline window (if receiving your heart rate accurately) will show current BPM, and the small
red light labeled PULSE adjacent to the incline window, will be illuminated. (If the receiver is not
receiving an accurate reading, the incline window will be flashing - - - -).
z To adjust the pre-set target heart rate press the TARGET +/TARGET– button then press the
ENTER PROGRAM button.
z Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the
belt starts moving.
z Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the
belt starts moving.
The small light at the top of the console labeled TARGET will be illuminated if you are at your target.
If you are not, the arrow shaped lights will illuminate and reflect if you are above or below your goal.
If you are not within 25 BPM of your “Target heart rate” the program will not work. DO NOT STOP
TO START OVER. Continue exercising and your heart rate will naturally increase. The program will
continually monitor your heart rate and periodically adjust the incline up or down to increase or
decrease the resistance thereby keeping you at your target zone. At the conclusion of the pro-
grammed time the TIME window will flash 00:00 and the CALORIES/DISTANCE window will contin-
ue to accumulate values. The treadmill will continue operation until the START/STOP button or the
PAUSE button is pressed. Press the POWER button to turn off the treadmill.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Program Instructions Heart rate Mode
TARGET UP
WORKOUT TIME
CALORIES/DISTANCE
TARGET ARROWS
START/STOP
POWER
TARGET DOWN
PAUSE
ENTER PROGRAM
INCLINE WINDOW
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Program Profiles
SPEED
SPEED
12
11
10
9
8
7
6
5
4
3
INCLINE
INCLINE
12
11
10
9
8
7
6
5
4
3
2
1
2
1
1 2 3 4 5 6 7 8 9 1 0
1 2 3 4 5 6 7 8 9 1 0
The Rolling Hills Program is designed to
vary treadmill elevation while maintaining
a constant walking belt speed.
The Speed Intervals Program is designed to
vary treadmill speed while maintaining a con-
stant elevation.
Each program contains 10 segments or intervals. For instance, a 30 minute program will have 10 three-minute
segments (30 minutes divided by 10). Also, each preset program may be customized for speed, incline, or both.
Please see “Program and Operating Instructions” to customize each program.
SPEED
12
11
10
9
8
7
6
5
4
3
SPEED
12
11
10
9
8
7
6
5
4
3
INCLINE
INCLINE
2
1
2
1
1 2 3 4 5 6 7 8 9 1 0
1 2 3 4 5 6 7 8 9 1 0
The Plateau Program is designed to
gradually increase treadmill Speed and
elevation in the first segment (warm
up), and gradually decrease speed and
elevation in the last segment (cool
down).
The Weight Loss Program is designed to alternate
between the programmed speed and incline. The pro-
gram will alternate between: 1) the full programmed
incline and half the programmed speed, to 2) zero
incline and the maximum programmed speed.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Belt Adjustment and Tension
WARNING! Do not overtighten rollers! This will cause prema-
ture roller bearing failure!
Belt adjustment and tension performs two functions:
adjustment for tension and centering. Your new treadmill
comes pre-adjusted from the factory for tension and cen-
tering. Please follow the procedures below if the belt shifts
to the left or right while walking:
WALKING BELT IS SHIFTING TO THE LEFT (Diagram 1)
First, turn treadmill on to run at 1 mph. Using the hex key pro
ed, turn the left rear roller adjustment bolt ¼ turn in the clockw
direction. Next, run the treadmill at 2.5 mph. You should see t
start to correct itself by moving back towards the center. Rep
above procedure until the walking belt is centered. It may be neces-
sary to set walking belt tension once you have completed this proce-
dure if the belt feels like it is slipping while walking. Refer below to
the “Walking Belt Slipping” instructions.
WALKING BELT IS SHIFTING TO THE RIGHT (Diagram 2)
First, turn the treadmill on to run at 1 mph. Using the hex key
provided, turn the right rear roller adjustment bolt ¼ turn in
the clockwise direction. Next, run the treadmill at 2.5 mph.
You should see the belt start to correct itself, moving back
towards the center. Repeat the above procedure until the
walking belt is centered. It may be necessary to set walking
belt tension once you have completed this procedure if the bel
feels like it is slipping while walking. Refer below to the “Walkin
Slipping” instructions.
WALKING BELT IS SLIPPING DURING USE (Diagram 3)
First, unplug the power cord from the surge protector. Using the hex
key provided, turn both left and right rear roller adjustment bolts the
same distance, usually a ¼ turn in the clockwise direction.
Plug the power cord back into the surge protector and run
the treadmill at 2.5 mph. You should now walk on the belt
to determine if the belt is still slipping. Repeat the above
procedure until the walking belt is not slipping. The tension
should be just tight enough not to slip.
z Turning the hex key counter clockwise brings the rear
rollers and belt towards you.
z Turning the hex key clockwise pushes the rear roller
and belt away form you.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance Instructions
WARNING! Before performing any maintenance to your treadmill, always unplug the power cord from the
surge protector.
CLEANING
Routine cleaning of your Smooth treadmill will extend the life of your treadmill. WARNING! To prevent electri-
cal shock, be sure the power to the treadmill is OFF and the unit unplugged from the wall electrical outlet
before attempting any cleaning or maintenance.
AFTER EACH WORKOUT: Wipe off the console and other treadmill surfaces with a clean, water damp-
ened soft cloth to remove excess perspiration. USE NO CHEMICALS.
WEEKLY: Use of a treadmill mat is recommended for ease of cleaning. Dirt from your shoes contacts the belt
and eventually makes it to underneath the treadmill. Vacuum underneath treadmill once a week.
DECK LUBRICATION
The walking belt has been pre-lubricated at the factory. However, it is recommended that the walking board be
checked periodically for lubrication to ensure optimal treadmill performance.
Every 30 days or 30 hours of operation, lift the sides of the walking belt and feel the top surface of the walking
board as far under as you can reach. If you feel signs of silicone, no further lubrication is required. If it feels
dry to the touch, follow the instructions below.
Smooth recommends “Lube N Walk” for cleaning and lubricating the treadmill belt and deck. You may also use
silicone such as “Napa 8300” (available at most stores).
TO APPLY LUBRICANT TO THE WALKING BOARD
1) Position the walking belt so that the seam is located on top and in the center of the center of the walking
board.
2) Insert the spray nozzle into the spray head of the lubricant can.
3) While lifting the side of the walking belt, position the spray nozzle between the walking belt and the board
approximately 6” from the front of the treadmill. Apply the silicone spray to the walking board, moving from the
front of the treadmill to the rear. Repeat this on the other side of the belt. Spray approximately 4 seconds on
each side.
4) Allow the silicone to ‘set’ for one minute before using the treadmill.
WARNING: Do not overlubricate the walking board. Excess lubricant should be wiped off with a clean towel.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
Treadmill will not start.
1 Is the Safety Key inserted into the treadmill Console?
2 Make sure the power cord is plugged into a surge protector, the surge protector is
plugged into a properly grounded outlet, and the surge protector is turned on. (Refer to
“Power Requirements” on page 8)
3 Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it
has tripped. Wait five minutes and then press the switch back in.
4 Check the house electrical breaker box and the circuit breaker for the room where the
treadmill is located. If it has tripped, reset or have an electrician replace the breaker in
home.
5 Have an electrician check for inadequate voltage at the outlet.
Treadmill loses power during use.
1 Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it
has tripped. Wait five minutes and then press the switch back in.
2 Check the house electrical breaker box and the circuit breaker for the room where the
treadmill is located. If it has tripped, reset or have an electrician replace the breaker in
home.
3 If the treadmill still will not operate, please call Technical Service at (888) 340-0482.
Treadmill walking belt slows during use.
1 Check to make sure the treadmill is securely plugged into an UL-listed surge protector,
rated at 15 amps, with a 14-gauge cord of five feet or less and the surge protector is
securely plugged into the outlet.
2 If treadmill still will not operate, please call Technical Service at (888) 340-0482.
Treadmill walking belt slips or is not centered on rear roller.
1 Refer to “Belt Adjustment and Tension” section on page 16.
2 Need help? Call Technical Service at (888) 340-0482.
Treadmill Error Messages.
Your treadmill is equipped with a software package that enables error messages to be dis-
played when there is a problem. To avoid possible damage to the treadmill and the
possibility of injury, do not operate the treadmill until the problem is corrected.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts & Exploded View
Part #
Part #
06-0039
23-0134
06-0040
1
2
3
Left Side Extrusion Rail
Right Side Extrusion Rail
05-0045
05-0045
12 Front Wheel (2)
13 Uprights for Console (2)
14 Motor Hood Cover Top
Treadmill Belt
AeroBelt
04-0010
04-0014
4
5
6
7
8
9
Front Roller Assembly
Rear Roller
24-0106
09-0009
03-0016
06-0043
06-0042
10-0008
various
15 Motor Drive Belt
16 Motor
04-0023
12-0004
12-0026
24-0216
Treadmill Deck
17 Elevation Motor (acuator)
18 Console Assembly
19 N/A
Left End Cap
Right End Cap
Rear Adjustable Foot (2)
20 Handlebars
various
08-0027
08-0052
10 Main Frame
21 Toggle switches (2)
11 Bottom Motor Pan
06-0041
22 Lower Electronics M/Control P/Supply
(855)
22 Controller
08-0050
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SMOOTH 9.2HR and 9.2HRAB Treadmills – LIMITED WARRANTY
CONSULT YOUR PHYSICIAN BEFORE USING THIS PRODUCT.
This Limited Warranty applies in the United States to products manufactured or distributed by Smooth Fitness (“Smooth”) under the SMOOTH brand name. The RE-
SIENTIAL warranty period to the original purchaser is (lifetime) on the frame, (10) years on the motor, (3) years on parts, and (1) year labor. This warranty does not cover wear and
tear, only manufacturer defects for the periods specified. LIGHT INSTITUTIONAL WARRANTY is limited to specific settings (see below) and includes an original purchaser warranty
of (1) year on the Frame, Motor, Parts, and (1) year labor.
Smooth warrants that the Product you have purchased for non-commercial, personal, family, or household use from Smooth or from an authorized Smooth reseller is
free from defects in materials or workmanship under normal use during the warranty period. Your sales receipt, showing the date of purchase of the Product, is your proof of the
date of purchase. This warranty only extends to you, the original purchaser. It is not transferable to anyone who subsequently purchases the Product from you. It excludes
expendable parts. This Limited Warranty becomes VALID ONLY if the treadmill is purchased from a Smooth Fitness authorized dealer unless otherwise authorized by Smooth
Fitness in writing (if anyone other than a Smooth Fitness authorized dealer sells a Smooth Fitness treadmill, the warranty will be void unless accompanied by written authorization by
Smooth Fitness).
During the warranty period Smooth will at no additional charge, repair or replace (at Smooth’ option) the part or product if it becomes defective, malfunctions, or
otherwise fails to conform with this Limited Warranty under normal non-commercial, personal, family or household use. In repairing the Product, Smooth may replace defective
parts, or at the option of Smooth, serviceable used parts that are equivalent to new parts in performance. All exchanged parts and Products replaced under this warranty will
become the property of Smooth. Smooth reserves the right to change manufacturers of any part to cover any existing warranty.
To obtain warranty service, you must contact a Smooth authorized service technician or Smooth Fitness at our phone numbers located in this manual. Any parts
determined to be defective must be returned to Smooth to obtain warranty service. You must prepay any shipping charges, export taxes, custom duties and taxes, or any other
charges associated with transportation of the parts or Product. In addition, you are responsible for insuring any parts or Product shipped or returned. You assume the risk of loss
during shipment. You must present Smooth with proof-of-purchase documents (including the date of purchase). Any evidence of alteration, erasing or forgery of proof-of-purchase
documents will be cause to void this Limited Warranty.
This warranty does not extend to any product not purchased from Smooth or from an authorized Smooth reseller. This Limited Warranty does not extend to any Product
that has been damaged or rendered defective; (a) as a result of accident, misuse, or abuse; (b) by the use of parts not manufactured or sold by Smooth; (c) by modification of the
Product or normal wear and tear; (d) operation on incorrect power supplies; or (e) as a result of service by anyone other than Smooth, or an authorized Smooth warranty service
provider. Product on which the serial number has been defaced or removed is not eligible for warranty service. Should any Product be submitted for warranty service be found
ineligible therefore, an estimate of repair cost will furnished and the repair will be made if requested by you upon Smooth’s receipt of payment or acceptable arrangements for
payment.
LIGHT INSTITUTIONAL SETTINGS as defined here include hotel, motel, hospital or rehabilitation centers, multi-family dwellings (condominium or apartment com-
plexes), police departments, fire departments, corporate wellness centers and the like. Any setting or application where usage would be more than six (6) hours per day will void the
warranty. Health clubs, fitness centers, spas, and the like that have a membership fee are excluded as light-institutional settings, whereas the Product will carry no warranty in these
settings. Written authorization from Smooth Fitness must be obtained regarding any other light-institutional uses.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, SMOOTH MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SMOOTH EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS
LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. NEITHER SMOOTH
NOR ANY OF ITS AFFILIATES SHALL BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR
EXCLUSION MAY NOT APPLY TO YOU. This Limited Warranty gives you specific legal rights and you may also have other rights that may vary from state to state. This is the only
express warranty applicable to Smooth-branded products. Smooth neither assumes nor authorizes anyone to assume for it any other express warranty.
PLEASE MAIL WARRANTY CARD TO: SMOOTH FITNESS, PO BOX 551239, DALLAS, TX 75355.
SMOOTH TREADMILL WARRANTY REGISTRATION
TELEPHONE
LAST
M.I.
FIRST
ADDRESS
CITY
APT. NO.
ZIP
STATE
DATE OF PURCHASE
SERIAL NO.
MODEL NO.
SMT9.2
How important are each feature:
Least Most
Unique Features
Horsepower
Warranty
Price
Look/Design
Folding Feature
Other Comments:
_______________
Where did you learn about treadmills?
TV____ Radio____ Friend____
Name of store or company where
purchased:
_______________
_______________
_______________
In Store Display____ Salesperson___
Print ad/flyer____ Internet______
How do you plan to use the treadmill?
Walk____ Run_____ Both_____
Who will use the treadmill?
Male____ Female_____ Both_____
Why did you purchase a treadmill?
Smooth Fitness respects the rights of your privacy. Our
company will not sell or distribute to others the information
above. This information is used to track our product
quality and to contact you in the event of a product safety
concern. It may be used to offer you future product
offerings only from Smooth. Please check here if wish not
to receive any additional information.
Dr.’s Orders____ Loose Weight____
In-home convenience____
Improve Cardiovascular Fitness___
Safety from outdoors____
How many family members? _____
AGE:
15-24____ 25-34____
35-44____ 45-54____
55-64____ 65 +_____
Other __________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
|