Smooth 5.3P Treadmill
O
W
treadmillbynet.com
advancedfitness.com
The Fitness Superstore
-
SALES: (888) 9TREADS
(888) 987-3237
SERVICE: (888) 340-0482
SMOOTH is a registered trademark of
Internetfitness.com
Mt. Laurel, NJ
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Information
NING!
1) WARNING: Before using this treadmill or starting any exercise program, consult your physician. This is
especially important for persons over the age of 35 and/or persons with pre-existing health problems. The
manufacturer or distributor assumes no responsibility for personal injury or property damage sustained by or through
the use of this product.
2) WARNING: To reduce the risk of electrical shock, burns, fire, or other possible injuries to the user, it is important
to review this manual and the following precautions before operation.
SAFETY PRECAUTIONS AND TIPS
„
It is the owner’s responsibility to ensure that all users of this treadmill have read the Owner’s Manual and are familiar
with warnings and safety precautions.
„
„
This treadmill has a user maximum capacity of 300 pounds for the 5.3P.
The treadmill should only be used on a level surface and is intended for indoor use only. The treadmill should not
be placed in a garage, patio, or near water and should never be used while you are wet. Smooth recommends a
treadmill mat be placed under the treadmill to protect floor or carpet and for easier cleaning.
„
„
Follow safety information in regards to plugging in your treadmill. Keep the power cord away from the incline wheels
and do not run the power cord underneath your treadmill. Do not operate the treadmill with a damaged or frayed
power cord.
Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not use the treadmill with
bare feet, sandals, socks or stockings.
„
„
„
„
„
„
„
„
„
„
Always straddle the belt and allow it to start moving before stepping onto the belt.
Hold on to handrails when adjusting speed, incline, or other controls.
Always examine your treadmill before using to ensure all parts are in working order.
Allow the belt to fully stop before dismounting.
Pets should be never be allowed near or on the treadmill.
Do not leave children unsupervised near or on the treadmill.
Never operate the treadmill where oxygen is being administered, or where aerosol products are being used.
Never insert any object or body parts into any opening.
For safety and to prevent damage to your treadmill, no more than one person should use the treadmill at a time.
Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed by
an authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to follow
these instructions will void the treadmill warranty.
„
Never leave the treadmill unattended while it is running.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start
Thank you for purchasing a SMOOTH treadmill! This quality product you have chosen
was designed to meets your needs for cardiovascular exercise.
• Before you start, please read the Owner’s Manual and become familiar with the
operation of your new treadmill. Remember to take the time to perform the stretching
exercises provided to avoid injury.
• The Red Safety Key is required to operate the treadmill.
• Do not stand on the walking belt while pressing the Power button or Start/Stop button.
• Always adjust the speed of the treadmill in small increments as this treadmill is capable
of high speeds.
• If you are taking medication, consult your physician to see if the medication will affect
your exercise heart rate.
• If you have heart problems, you are not active, and/or are over the age of 50 years, do
not use the pre-set treadmill programs or start an exercise program without first
contacting and receiving approval from your physician.
• To avoid the risk of electrical shock, always keep the console dry. Do not spill liquids
on the console. The manufacturer recommends a sealed water bottle for beverages
consumed while using the treadmill.
• Please review the following drawing below to familiarize yourself with the listed
parts. The one pictured below may not be identical to your particular model.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Warm Up Exercises
NING!
WARM UP FIRST !
Warming up prepares the body for exercise by increasing circulation, supplying more
oxygen to the muscles and raising body temperature. Begin each workout with 5 to 10
minutes of stretching and light exercise to warm up. The drawings on this page show
several forms of basic stretching you may perform before your workouts. Again, consult a
physician before starting this or any other exercise program.
15 Seconds for each
20 Seconds
20 Seconds
20 Seconds
30 Seconds
20 Seconds
20 Seconds
25 Seconds
30 Seconds
25 Seconds each leg
20 Seconds
5 Seconds X 3 times
25 Seconds each leg
5 Times
15 Seconds
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
Assembly
The Smooth 5.3P treadmill is shipped in one piece to make assembly easy. After opening the
box, remove any packing materials from the treadmill. Do not throw away any packing materials
until the unit is working properly. Place the base on a clean, level surface. Make sure the
electrical cord will easily reach an electrical outlet.
1) Have a second person raise the console to the upright position and hold.
2) Insert 3/4” Button Head Bolts in upright (see diagram) and tighten lightly.
3) Insert the TUBE SPACER inside the upright frame and line up with the bottom hole. Hold tube
spacer while inserting the 1 1/2” Button Head Bolt and lightly tighten. Repeat for opposite side.
4) After completing opposite side, Tighten all four assembled bolts.
5) Assembly is now complete. The RED SAFETY KEY is required to be placed on the console for
operation.
Insert 3/4” bolt
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Requirements
WARNING!
IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT
IN A RISK OF AN ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR
SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE PRODUCT IS PROPERLY
GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL
NOT FIT THE OUTLET, HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED
ELECTRICIAN.
This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage
spikes, surges, and noise interference can result from weather conditions or from other appliances being turned on or
off. To reduce the possibility of treadmill damage, always use a surge protector (not included) with your treadmill.
Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge
protector with a UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage
rating of 400V or less and an electrical rating of 120VAC, 15 amps.
This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance
for electric current, should the treadmill malfunction. This treadmill comes with an electrical cord having an
equipment-grounding conductor and a grounding plug. Always plug the power cord into a surge protector, and plug
the surge protector into an appropriate outlet that is properly installed and grounded in accordance with all local
codes and ordinances.
This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in the
drawing (1) below.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Console Functions and Descriptions
There are five display windows on the control panel to provide you with vital feedback information.
TIME WINDOW
•TIME: Indicates elapsed time after pressing start in minutes and seconds (0-99 minutes, 0-59 seconds)
•INTERVAL TIME: Indicates countdown in seconds to the next interval starting at 5 seconds and counting to 0
seconds
SPEED WINDOW
•SPEED: Indicates MPH (miles per hour) or Km/H (kilometer per hour) in .1 increments
DISTANCE / CALORIES WINDOW
•DISTANCE: Indicates Miles or Kilometers traveled in .01 increments up to 9.99 and .1 increments starting at 10.0
•CALORIES: Indicates estimated calories used based on 150 lb. person at the indicated speed, incline, and time
INCLINE WINDOW
•INCLINE: Indicates incline in percent of grade 0-12% in 1% increments
CENTER BRICKYARD
•Displays quarter mile track in Manual mode. Indicates position on track by a blink. In program mode, shows the
change in speed profile across the interval range (1-10) and shows position with a blinking action.
SPEED BAR
•The Speed Bar allows the user to adjust speed quickly. The Speed Bar works in all manual and program modes. To use
the Speed Bar, the belt must already be moving. Press the desired speed (2 through 8), and the treadmill will slowly reach
the speed selected. In program mode, the change in speed with the Speed Bar will only work in the current interval. Once
the program switches to another interval, the speed will revert to the programmed speed.
TOGGLE SWITCHES IN HANDLEBARS FOR SPEED AND INCLINE
Your treadmill is equipped with toggle switches that conveniently change the incline and speed without reaching up to the
console. In program mode, the change in speed and/or incline with the toggle switches will only work in the current interval.
Once the program switches to another interval, the speed and incline will revert to the programmed speed and incline.
LED INDICATORS
•PROGRAM SELECTION: The treadmill console will display the program selected with a LED light beside the
program., showing on the left hand side of the window.
•TIME: LED indicators will toggle back and forth for the Interval Time and the Workout Time. The Interval Time will
be indicated while in a program. The total time for each Interval is the workout time set at the beginning of a
program divided by 10. For example, a 30-minute program will have 10 segments of 3 minutes each . The Workout
Time is the total time set at the beginning of a program, and will count down from the amount of time set throughout
the program.
•CALORIES & DISTANCE: LED indicators will toggle back and forth to show total Calories burned and total Distance
covered. The Calorie estimate is based on a 150 lb person at the current speed and incline levels.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Program and Operating Instructions
QUICK START / MANUAL MODE
•
•
•
•
Plug into a standard wall outlet (110-Volt AC, 15-amp circuit).
Attach Safety Key to treadmill console.
Stand on the treadmill and straddle belt.
Press POWER button. There will be an eight (8) second delay after pressing the POWER button before data can
be entered. The TIME window will flash.
•
Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts
moving. Speed or incline may be adjusted by using the appropriate + (increase) or – (decrease) buttons.
•
•
•
To end your workout, press START/STOP button. Belt will gradually slow to zero.
To pause your workout, press PAUSE.
To re-start after pausing: Press the PAUSE button. WARNING: The treadmill belt will resume at the speed the
treadmill was moving before pausing.
•
Countdown Time, Preset Speed and/or Incline: Time, Speed, and Incline may be preset prior to getting
started. After pressing the POWER button, the time window will blink. Use the SPEED/TIME + or – arrows to
select your workout time, then press the ENTER PROGRAM button. The SPEED/TIME window will now be
flashing. Using the same + or – arrows, select the speed for your workout, then press ENTER PROGRAM. Now
the INCLINE window will be flashing. Use the INCLINE + or – arrows to set your workout incline, then press
ENTER PROGRAM. To start, press the START/STOP button.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Program and Operating Instructions
PROGRAM MODE
•
•
•
•
Plug into a standard wall outlet (110-Volt AC, 15-amp circuit).
Attach RED Safety Key to treadmill console.
Stand on the treadmill and straddle belt.
Press POWER button. There will be an eight (8) second delay after pressing the POWER button before data can
be entered. The TIME window will flash.
•
There are four (4) pre-set programs in the 5.3P. The 5.3P includes Rolling Hills, Speed Intervals, Plateau, Weight
Loss and User programs (see the program profiles later in this manual). Select the program by pressing the
appropriate button.
•
•
•
Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts
moving.
Each of the pre-set programs can also be customized. Follow the instructions below for your particular
model.
SMOOTH 5.3P: Customizing programs in P1 and P2 Mode: Each pre-set program can be customized in the
P1 or P2 mode. After making the program selection, the top right window (CALORIES / DISTANCE) will read
“OP.” ”OP” refers to “original program” and is preset. Press the same program button once more, and the
CALORIE / DISTANCE window will read P1. The “P1” mode is now accessed. You can now program the Time,
Speed, and Incline in P1 mode, which will save your entered information for future use. The time window will
blink. Use the SPEED/TIME + or – arrows to select your workout time, then press the ENTER PROGRAM
button. The SPEED/TIME window will now be flashing. Using the same + or – arrows, select the speed for your
workout, then press ENTER PROGRAM. Now the INCLINE window will be flashing. Use the INCLINE + or –
arrows to set your workout incline, then press ENTER PROGRAM. To start, press the START/STOP button. To
access P2 mode, press the selected program button three times (once for OP, twice for P1, three times for P2).
Follow the above procedure to customize.
•
•
User Programs: The 5.3P also has two (2) User programs so that you may customize each of the 10 program
segments. Press the User program button, the time window will flash. Set your workout time. Notice the first
segment light flashing in the center brickyard. Now the SPEED window will flash, set your speed for the first
segment. Now the INCLINE window will flash. Set the incline. At this point, look at the center brickyard and
notice the second segment light is now flashing. Repeat steps above to program all ten segments.
TO CHANGE A PREVIOUSLY PROGRAMMED P1, P2, or user program: Once you have programmed the P1
or P2 modes, you will need to use the PAUSE button to change the program you previously entered. For
instance, if P1 in Rolling Hills has been programmed, to change to a new setting, press the Rolling Hills button
twice to access P1. Then press the PAUSE button to get the TIME window to flash. Follow the directions above
to continue to change the program.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Program Profiles
The Rolling Hills Program is designed to vary
treadmill elevation while maintaining a constant
walking belt speed.
The Speed Intervals Program is designed to vary treadmill
speed while maintaining a constant elevation.
Each program contains 10 segments or intervals. For instance, a 30 minute program will have 10 three-minute
segments (30 minutes divided by 10). Also, each preset program may be customized for speed, incline, or both.
Please see “Program and Operating Instructions” to customize each program.
The Plateau Program is designed to gradually
increase treadmill Speed and elevation in the first
segment (warm up), and gradually decrease speed
and elevation in the last segment (cool down).
The Weight Loss Program is designed to alternate between
the programmed speed and incline. The program will
alternate between: 1) the full programmed incline and half
the programmed speed, to 2) zero incline and the
maximum programmed speed.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Belt Adjustment and Tension
WARNING! Do not overtighten rollers! This will cause premature roller bearing failure!
Belt adjustment and tension performs two functions: adjustment for tension and centering. Your
new treadmill comes pre-adjusted from the factory for tension and centering. Please follow the
procedures below if the belt shifts left or right or if the belt slips while walking:
WALKING BELT HAS SHIFTING TO THE LEFT (Diagram 1)
First, unplug the power cord from the surge protector. Using the hex key provided, turn the left
rear roller adjustment bolt ¼ turn in the clockwise direction. Plug the power cord back into the
surge protector and run the treadmill at 2.5 mph. You should see the belt start to correct itself,
moving back towards the center. Repeat the above procedure until the walking belt is centered.
It may be necessary to set walking belt tension once you have completed this procedure if the belt
feels like it is slipping while walking. Refer to below to the “Walking Belt Slipping” instructions.
WALKING BELT HAS SHIFTING TO THE RIGHT (Diagram
2)
First, unplug the power cord from the surge protector. Using
the hex key provided, turn the right rear roller adjustment bolt
¼ turn in the clockwise direction. Plug the power cord back
into the surge protector and run the treadmill at 2.5 mph. You
should see the belt start to correct itself, moving back towards
the center. Repeat the above procedure until the walking belt
is centered. It may be necessary to set walking belt tension
once you have completed this procedure if the belt feels like it
is slipping while walking. Refer to below to the “Walking Belt
Slipping” instructions.
WALKING BELT IS SLIPPING DURING USE (Diagram 3)
First, unplug the power cord from the surge protector. Using
the hex key provided, turn both left and right rear roller
adjustment bolts the same distance, usually a ¼ turn in the
clockwise direction. Plug the power cord back into the surge
protector and run the treadmill at 2.5 mph. You should now
walk on the belt to determine if the belt is still slipping. Repeat
the above procedure until the walking belt is not slipping. The
tension should be just tight enough not to slip.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance Instructions
WARNING! Before performing any maintenance to your treadmill, always unplug
the power cord from the surge protector.
CLEANING
Routine cleaning of your Smooth treadmill will extend the life of your treadmill. WARNING! To prevent electrical
shock, be sure the power to the treadmill is OFF and the unit unplugged from the wall electrical outlet before
attempting any cleaning or maintenance.
AFTER EACH WORKOUT: Wipe off the console and other treadmill surfaces with a clean, water dampened soft
cloth to remove excess perspiration. USE NO CHEMICALS.
WEEKLY: Use of a treadmill mat is recommended for ease of cleaning. Dirt from your shoes contacts the belt and
eventually makes it to underneath the treadmill. Vacuum underneath treadmill once a week.
DECK LUBRICATION
The walking belt has been pre-lubricated at the factory. However, it is recommended that the walking board be
checked periodically for lubrication to ensure optimal treadmill performance. Your treadmill should not have to be
lubricated usually within the first year or 500 hours of use. If you have questions, call us at (888) 340-0482.
Every 30 days or 30 hours of operation, lift the sides of the walking belt and feel the top surface of the walking board
as far under as you can reach. If you feel signs of silicone, no further lubrication is required. If it feels dry to the
touch, follow the instructions below.
Please use Lube ‘N Walk (can be purchased from your dealer or call the number on the front of the manual), or a
non-petroleum based silicone such as “Napa 8300” (available at most stores).
TO APPLY LUBRICANT TO THE WALKING BOARD
1) Position the walking belt so that the seam is located on top and in the center of the center of the walking board.
2) Insert the spray nozzle into the spray head of the lubricant can.
3) While lifting the side of the walking belt, position the spray nozzle between the walking belt and the board
approximately 6” from the front of the treadmill. Apply the silicone spray to the walking board, moving from the front
of the treadmill to the rear. Repeat this on the other side of the belt. Spray approximately 4 seconds on each side.
4) Allow the silicone to ‘set’ for one minute before using the treadmill.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
Treadmill will not start.
1) Make sure the power cord is plugged into a surge protector, the surge protector is plugged into a
properly grounded outlet, and the surge protector is turned on. (Refer to “Power Requirements”)
2) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has tripped.
Wait five minutes and then press the switch back in.
3) Check the house electrical breaker box and the circuit breaker for the room the treadmill is located in.
If it has tripped, reset or have an electrician replace the breaker in home.
4) Have an electrician check for inadequate voltage at the outlet.
Treadmill looses power during use.
1) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has tripped.
Wait five minutes and then press the switch back in.
2) Check the house electrical breaker box and the circuit breaker for the room the treadmill is located in.
If it has tripped, reset or have an electrician replace the breaker in home.
If treadmill still will not operate, please call Technical Service at (888) 340-0482.
Treadmill walking belt slows during use.
1) Check to make sure the treadmill is securely plugged into an UL-listed surge protector, rated at 15
amps, with a 14-guage cord of five feet or less and the surge protector is securely plugged into the
outlet.
If treadmill still will not operate, please call Technical Service at (888) 340-0482.
Treadmill walking belt slips or is not centered on rear roller.
1) Refer to “Belt Adjustment and Tension” section.
2) Need help? Call Technical Service at (888) 340-0482.
Treadmill Error Messages.
Your treadmill is equipped with a software package that enables error messages to be displayed when
there is a problem. To avoid possible damage to the treadmill and the possibility of injury, do not
operate the treadmill until the problem is corrected.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List - Smooth 5.3P
KEY #
PART #
DESCRIPTION
QTY
KEY #
53
PART #
DESCRIPTION
QTY
1
2
UP 3K ASSB UPRIGHT ASSEMBLY
1
1
1
08-0004 CIRCUIT BREAKER 15 AMP
13-0017 TELCO HARNESS FOR HEART RATE
11-0002 REAR ELEVATION BUSHING
11-0003 UPRIGHT PIVOT BUSHING
1
1
2
2
20-0001
20-0003
DECK ASSEMBLY
54
3
ELEVATION ASSEMBLY
55
4
56
5
6
7
19-0014
19-0015
19-0029
19-0019
MOTOR MOUNTING BRACKET
MOTOR COVER BRACKET
OPTICAL WHEEL BRACKET
BELT GUIDE
1
6
1
2
59
60
62
63
64
65
66
67
68
69
70
71
72
76
77
78
79
80
81
82
83
84
85
87
88
89
91
93
94
CONSOLE DECAL
1
1
8
MOTOR COVER DECAL
9
14-0024 SAFETY LATCH DECAL N/S
14-0025 WARNING FOLDING DECAL N/S
14-0026 WARNING CONSOLE DECAL N/S
02-0078 MOTOR TENSION SPRING
02-0002A DECK LIFT SPRING
1
10
1
1
12
13
19-0032
06-0018
24-0151
05-0019
05-0020
06-0027
SPRING ANCHOR BRACKET
BASE PAN MOTOR
2
1
1
1
1
2
1
1
1
1
2
4
1
1
4
1
2
2
2
3
8
2
1
4
CONSOLE ASSEMBLY
02-0004 SCREW, 8X 5/8 PHIL PH
02-0005 SCREW, 8X 5/8 PHIL PH HILO
02-0006 BOLT, 5/16 X 5 - 1/2 SHOULDER BOLT
02-0007 5/16-18 NYLOCK NUT
02-0008 BOLT, 5/16-18 X 3/4 GRADE 2 ZP
02-0009 NUT, 5/16-18 WHIZLOC
02-0013 LOCK WASHER, 1/4
40
8
16
16
17
SIDE BOARD EXTRUSION RIGHT
SIDE BOARD EXTRUSION LEFT
PIVOT SUPPORT COVER
1
3
3
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
06-0053
06-0071
06-0020
06-0004
06-0005
06-0007
06-0008
06-0009
06-0019
06-0011
06-0012
06-0013
10-0004
10-0002
10-0013
3-PC LCD CENTER PLASTIC CONSOLE
FAN 5" 5/8” ID
3
8
BASE PAN END
02-0014 BOLT, 1/4-20 X 2 - 1/2 HEX
02-0015 SPRING WASHER
10
4
BASE PLUG
DOME PLUG
02-0016 BOLT, 3/8-16 X 2 - 1/2 HEX
02-0017 NUT, 3/8-16 NYLOCK
1
MOTOR COVER
2
END CAP
02-0018 PUSH NUT, 3/8 HAT
4
S.E.S. EXTENSION GLIDE
BASE PAN CENTER
2" ROLLER WHEEL
3” ROLLER WHEEL
UPRIGHT SPACE
RUBBER FOOT
02-0019 CARRIAGE BOLT 10-24 X 1-1/2
02-0020 SCREW, 1/4-20 X 2-1/2 SOCKET HEAD
02-0021 WASHER, 9/32 X 5/8 X 1/8
02-0022 NUT, 10-24 NYLOCK
4
2
3
4
02-0024 CARRIAGE BOLT 5/16 X 1
02-0025 WHEEL AXLE
2
2
BOARD ISOLATOR
GRIP MOLDED WITH REMOTE
02-0026 PUSH NUT
10
1
02-0028 SAFETY KEY
02-0030 SCREW, 8-32 X 5/8 HEX TRILOBE
02-0031 SCREW, 3/8-16 X 1 3/4 HEX
1
37
38
39
40
41
42
43
44
45
12-0022
12-0018
03-0006
04-0012
04-0004
09-0012
09-0013
13-0011
13-0003
ACTUATOR (ELEVATION MOTOR)
DRIVE MOTOR
1
1
1
1
1
1
1
1
1
1
WALKING BOARD EXTRA LONG
WALKING BELT EXTRA LONG
POLY V BELT
97
98
99
02-0034 SCREW, 8-32 X 5/8 PPH N/SHOWN
02-0035 NUT, 8-32 NYLOCK NOT SHOWN
02-0036 SCREW, GREEN HEAD 8 X 5/8 PPH
08-0094 MEM, LCD PROGRAM WITH INCLINE 815
08-0089 MEM, LCD POWER 815 AND 835HR
02-0040 GUIDE TUBE RETAINER NOT SHOWN
14-0027 EMERGENCY STOP DECAL
1
4
FRONT ROLLER ASSEMBLY
REAR ROLLER
2
1
POWER CORD
1
ENCODER HARNESS
103
104
105
107
108
109
110
111
1
1
06-0014 BUSHING, STRAIN RELIEF
1
48
49
13-0016
13-0007
CONTROL PANEL HARNESS
JUMPER WIRE 6" NOT SHOWN
1
1
06-0016 WIRE TIES NOT SHOWN
10
5
06-0021 WIRE CLAMP NOT SHOWN
06-0022 RESET GUIDE TUBE NOT SHOWN
06-0024 HEX WRENCH CLIP NOT SHOWN
10-0007 6" CROSS HANDLEBAR FOAM GRIP
1
51
52
08-0050
08-0047
MOTOR CONTROLLER
OPTICAL ENCODER
1
1
1
2
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Exploded View 5.3P
Download from Www.Somanuals.com. All Manuals Search And Download.
Smooth Treadmills – LIMITED WARRANTY
CONSULT YOUR PHYSICIAN BEFORE USING THIS PRODUCT.
This Limited Warranty applies in the United States to products manufactured or distributed by Smooth Fitness (“Smooth”) under the SMOOTH brand name.
The warranty period to the original purchaser is (lifetime) on the frame, (5) years on the motor, (2) years on parts, and (1) year labor. This warranty does not cover wear
and tear, only manufacturer defects for the periods specified.
Smooth warrants that the Product you have purchased for non-commercial, personal, family, or household use from Smooth or from an authorized Smooth
reseller is free from defects in materials or workmanship under normal use during the warranty period. Your sales receipt, showing the date of purchase of the Product,
is your proof of the date of purchase. This warranty only extends to you, the original purchaser. It is not transferable to anyone who subsequently purchases the
Product from you. It excludes expendable parts. This Limited Warranty becomes VALID ONLY if the treadmill is assembled/installed by a Smooth Fitness authorized
dealer/technician unless otherwise authorized by Smooth Fitness in writing (if anyone other than a Smooth Fitness authorized dealer/technician assembles a Smooth
Fitness treadmill the warranty will be void unless accompanied by written authorization by Smooth Fitness).
During the warranty period Smooth will at no additional charge, repair or replace (at Smooth’ option) the part or product if it becomes defective,
malfunctions, or otherwise fails to conform with this Limited Warranty under normal non-commercial, personal, family or household use. In repairing the Product,
Smooth may replace defective parts, or at the option of Smooth, serviceable used parts that are equivalent to new parts in performance. All exchanged parts and
Products replaced under this warranty will become the property of Smooth. Smooth reserves the right to change manufacturers of any part to cover any existing
warranty.
To obtain warranty service, you must contact a Smooth authorized service technician or Smooth Fitness at our phone numbers located in this manual. Any
parts determined to be defective must be returned to Smooth to obtain warranty service. You must prepay any shipping charges, export taxes, custom duties and
taxes, or any other charges associated with transportation of the parts or Product. In addition, you are responsible for insuring any parts or Product shipped or
returned. You assume the risk of loss during shipment. You must present Smooth with proof-of-purchase documents (including the date of purchase). Any evidence
of alteration, erasing or forgery of proof-of-purchase documents will be cause to void this Limited Warranty.
This warranty does not extend to any product not purchased from Smooth or from an authorized Smooth reseller. This Limited Warranty does not extend to
any Product that has been damaged or rendered defective; (a) as a result of accident, misuse, or abuse; (b) by the use of parts not manufactured or sold by Smooth; (c)
by modification of the Product or normal wear and tear; (d) operation on incorrect power supplies; or (e) as a result of service by anyone other than Smooth, or an
authorized Smooth warranty service provider. Product on which the serial number has been defaced or removed is not eligible for warranty service. Should any
Product be submitted for warranty service be found ineligible therefore, an estimate of repair cost will furnished and the repair will be made if requested by you upon
Smooth’s receipt of payment or acceptable arrangements for payment.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, SMOOTH MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SMOOTH EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS
LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. NEITHER SMOOTH
NOR ANY OF ITS AFFILIATES SHALL BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR
EXCLUSION MAY NOT APPLY TO YOU. This Limited Warranty gives you specific legal rights and you may also have other rights that may vary from state to state. This
is the only express warranty applicable to Smooth-branded products. Smooth neither assumes nor authorizes anyone to assume for it any other express warranty.
PLEASE SEND IN THE ATTACHED WARRANTY CARD WITHIN TEN (10) DAYS OF PURCHASE TO REGISTER YOUR
TREADMILL WITH SMOOTH FITNESS PRODUCTS. MADE IN THE USA. Thank you for your business! PLEASE MAIL
WARRANTY CARD TO: SMOOTH FITNESS, PO BOX 551239, DALLAS, TX 75355.
SMOOTH TREADMILL WARRANTY REGISTRATION
TELEPHONE
LAST
M.I.
FIRST
ADDRESS
CITY
APT. NO.
ZIP
STATE
SERIAL NO.
DATE OF PURCHASE
MODEL NO.
How important are each feature:
Least Most
Unique Features
Horsepower
Warranty
Price
Look/Design
Folding Feature
Other Comments:
_______________
Where did you learn about treadmills?
TV____ Radio____ Friend____
Name of store or company where
purchased:
_______________
_______________
_______________
In Store Display____ Salesperson___
Print ad/flyer____ Internet______
How do you plan to use the treadmill?
Walk____ Run_____ Both_____
Who will use the treadmill?
Male____ Female_____ Both_____
Why did you purchase a treadmill?
Smooth Fitness respects the rights of your privacy. Our
company will not sell or distribute to others the information
above. This information is used to track our product
quality and to contact you in the event of a product safety
Dr.’s Orders____ Loose Weight____
In-home convenience____
Improve Cardiovascular Fitness___
Safety from outdoors____
How many family members? _____
AGE:
15-24____ 25-34____
35-44____ 45-54____
55-64____ 65 +_____
concern.
It may be used to offer you future product
offerings only from Smooth. Please check here if wish not
to receive any additional information on Smooth products.
Other __________________________
17
Download from Www.Somanuals.com. All Manuals Search And Download.
|