Sierra Video Game Controller S5832SG User Manual

Model S5832SG

Control Panel

8 to 32 Zones

Installation

Instructions

Downloaded from: http://www.guardianalarms.net

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Compliance and Regulatory Information ....................i

Programming the Panel ........................................ 8 - 10

Remote Programming (RPS)........................................ 8

Direct Connect ............................................................. 8

Keypad Activated RPS......................................... 8 - 9

Programming With an LED Keypad ............................ 9

Programming With an Alphanumeric Keypad ........ 10

Quick Programming Mode ...................................... 10

Menu Programming Mode ...................................... 10

Programming With an Icon Keypad .......................... 10

Installing and Connecting the Control Panel ..... 1 - 5

Sierra S5832SG PC Board Layout.............................. 1

Mounting the Panel.................................................. 1 - 2

Panel Setup and Installation ....................................... 1

Earth Ground ............................................................... 1

Mounting the Enclosures .............................................. 2

S5832S Enclosure (Small) ....................................... 2

S5832 Enclosure (Large) .......................................... 2

Backup Battery ................................................................ 3

Sierra Accessory Loading ............................................ 3

AH Requirements for Backup ...................................... 3

Determining Standby Battery Requirements ........ 3

AC Power ......................................................................... 3

Output Terminals ............................................................ 4

External Bell Supervision ............................................. 4

Keypad Wiring ................................................................ 4

Sierra Accessory Wiring Distances ......................... 4

Keypad Addressing .................................................... 5

Connecting an Auxiliary Keypad (J8) .................... 5

Zone Terminals ............................................................... 5

On-Board Relay Terminals (TB2) ................................ 5

Installer Mode Options, (Block 0) ..................... 11 - 12

Installer Walk-Test ........................................................ 11

Event Memory ............................................................... 11

Event Memory Codes...............................................11

Custom Messages ........................................................ 12

Test Report ..................................................................... 12

Test Report with Audibles ........................................... 12

Audible Test ................................................................... 12

Entry Delay Test ............................................................ 12

Exit Delay Test .............................................................. 12

Transmit Walk-Test Queue Reports .......................... 12

RPS Callback ................................................................ 12

Battery Test .................................................................... 12

Accessories .............................................................. 5 - 7

S5050 Relay/Event Memory Module.................... 5 - 6

Switch Settings............................................................ 6

Switch Configuration ................................................. 6

S5058 Zone Expansion Module.................................. 6

ZEM Addressing .......................................................... 6

SN915-BUS SpreadNet Receiver ............................... 7

SN990/991 SpreadNet Keypad/Remote ................... 7

SN961 SpreadNet Keyfob ............................................ 7

Programming Summary ...................................... 13 - 39

Block 1: Code Option Programming ............... 13 - 14

Block 2: Zone Configuration Programming ... 14 - 16

Block 3: Armed System Programming ............ 16 - 21

Block 4: Digital Communicator Programming 21 - 25

Block 5: Reporting Digits Programming ......... 25 - 29

Block 6: Real Time Clock Programming ................. 30

Block 7: Auxiliary Devices Programming....... 31 - 34

Block 8: SpreadNet Programming ............................ 35

Block 9: Partition (Area) Programming .......... 35 - 37

Block 10: User Code Programming ................ 37 - 39

Digital Communicator ............................................. 7 - 8

Removing/Installing the Digital Communicator ....... 7

Digital Communicator Terminal Connections..... 7 - 8

Terminal Connections ................................................... 8

Download from Www.Somanuals.com. All Manuals Search And Download.

Standby Battery Information

Country Specific Compliance Information

Singapore

The Table and worksheet below provide the installer with the infor-

mation necessary to determine the AH rating and battery require-

ments for any particular installation.

The following hardware and programming guidelines are required

for installation of this system in Singapore.

Sierra Accessory Loading

Product current consumption

Max. Standby

Max. Active

125 mA

50 mA

Hardware Requirements:

S5832 Control Panel

125 mA

1. The Digital Communicator must be Model S5070SG or S5070SG-2.

S5010 Alpha Keypad

S5020 LED Keypad

30 mA

50 mA

S5030 Icon Keypad

30 mA

50 mA

Programming Requirements:

S5050 REMM (up to 2)

S5058 ZEM (up to 3)

S5070 Single-line Dialer

S5070-2 Dual-line Dialer

SN915-BUS RF Receiver

100 mA (each)

40 mA (each)

35 mA

100 mA

40 mA**

60 mA

1. Dial Type (Block 4, CL 101) must be programmed for DTMF only.

2. Dial Attempts (Block 4, CL 102) must not be programmed to more

than 10.

35 mA

70 mA

125 mA

170 mA

**ZEM VOUT terminals can supply up to 300 mA (max.)

Malaysia

Table A - Standby Battery Loading

The following hardware and programming guidelines are required

for installation of this system in Malaysia.

AH Requirements for Backup

Hardware Requirements:

Product/Device

S5832SG

S5010

4-Hour

0.5 AH

0.12 AH

0.4 AH

0.16 AH

0.14 AH

0.5 AH

0.04 AH

0.1 AH

24-Hour

3.0 AH

0.72 AH

2.4 AH

72-Hour

9.0 AH

Qty Total

1. The Digital Communicator must be Model S5070SG or S5070SG-2.

2.16 AH

7.2 AH

S5020

Programming Requirements:

S5030

S5050

1. Dial Attempts (Block 4, CL 102) must not be programmed to more

than 3.

S5058

0.96 AH

0.84 AH

3.0 AH

2.88 AH

2.52 AH

9.0 AH

S5070(-2)

SN915-BUS

Sensor (10 mA)

Sensor (25 mA)

0.24 AH

0.6 AH

0.72 AH

1.8 AH

Bell/Siren (5 min) 0.085 AH

Bell/Siren (15 min) 0.225 AH

0.085 AH

0.225 AH

0.085 AH

0.225 AH

* Bell/Siren current may be 0.7 - 1.0 A

Total AH Required

Table B - AH Requirements

Determining Standby Battery Requirements

To calculate the size (AH rating) of your system's Backup Battery,

enter the Number (Qty) of devices of each type in the chart above.

Multiply the number of devices times the AH rating for the desired

backup period (Qty x AH = Total) and enter the total in the last

column. To determine the total AH rating of the battery, add all

values in the last column.

Total current from all sensors must be considered when calculat-

ing AH rating. For example:

10 sensors @ 10 mA = 100 mA

4 sensors @ 25 mA = 100 mA

Total current all sensors = 200 mA

Download from Www.Somanuals.com. All Manuals Search And Download.

S5832SG Terminal Layout

Nylon retaining

screw

Figure 1

S5832SG PCB Terminal Layout

Panel Setup and Installation

Introduction

This manual contains basic information and program-

ming information for the Sierra Model S5832SG con-

trol panel.

The first step in any installation process is careful planning

of the installation. Install the Sierra Model S5832SG in a

location as close as possible to power and phone lines. The

control panel is designed to operate as a local panel, with an

optional plug-on digital communicator.

For additional information regarding programming and

applications, refer to the Expanded Programming sec-

tion of the S5090 Sierra Reference Manual.

EarthGround

To ensure the effectiveness of the lightning and transient

protection circuits, the control panel must be connected to

"Earth Ground". Ideally, this should be a common ground to

the power lines, telephone system, and security system.

This type of ground, called a "Unified Earth Ground", pro-

vides the best protection. The ground connection, from a

grounding rod, cold water pipe or other established ground

point, is made to the green/yellow jacketed wire, providing a

ground to the panel housing.

Mounting the Panel

The Sierra S5832SG should be mounted in a location

which allows convenient access to AC power, tele-

phone connections, and earth ground (see Figure 2).

•

Remove the knock-outs, if necessary.

Mark the screw mounting holes on the wall, using

the cabinet as a template.

•

Mount the cabinet at the desired height and pass

the cables through the knock-outs.

Power

Lines

Telephone

Lines

Mount the circuit board to the stand-offs. The stand-

offs are factory installed. The metal stand-off (lower

left corner) has a panhead screw to be used for con-

necting earth ground.

Control

Panel

Power Line

Earth Ground

Telephone

Earth Ground

•

Connect the earth ground wire (green with yellow

stripe) to the board (see Figure 1) and cabinet. The

earth ground wire will connect to the upper hinge

when using the large enclosure and to the lower

hinge on the small enclosure.

Figure 2

Connecting to

Earth Ground

Unified Earth Ground

with Bonded Ground Roots

Download from Www.Somanuals.com. All Manuals Search And Download.

Housing Mounting Holes

Wiring Knock-outs

Figure 3 (a)

Mounting the S5832S

Enclosure

266 mm

10.5"

Wiring Knock-outs

Top

PCB Mounting

Hardware

(see page 1

for details)

Housing

Mounting Holes

Wiring Knock-outs

Left side

Wiring Knock-outs

Right side

Housing Mounting Holes

Wiring Knock-outs

Bottom

Figure 3 (b)

Mounting the S5832

Enclosure

Download from Www.Somanuals.com. All Manuals Search And Download.

Backup Battery

AH Requirements for Backup

The system employs one or more 6.5 AH (Model 1265) or 7.0

AH (Model 1270) sealed lead-acid storage battery. Connect

the battery to the control panel PCB via the red (+) and black

(-) leads. The battery should be replaced every 3 - 5 years.

Product/Device

S5832SG

4-Hour

0.5 AH

24-Hour

3.0 AH

72-Hour

9.0 AH

Qty.

Total

S5010

S5020

S5030

S5050

0.12 AH

0.4 AH

0.72 AH

2.4 AH

2.16 AH

7.2 AH

When connecting two or more batteries in parallel, use the

Model S5054 Auxiliary Battery Harness. Both batteries must

have the same AH (Ampere-Hour) rating and should have

the same lot number or date code. Figure 4, below, shows

correct method for wiring the batteries in parallel.

S5058

0.16 AH

0.14 AH

0.5 AH

0.04 AH

0.1 AH

0.96 AH

0.84 AH

3.0 AH

0.24 AH

0.6 AH

2.88 AH

2.52 AH

9.0 AH

0.72 AH

1.8 AH

S5070 (-2)

SN915-BUS

Sensor (10 mA)

Sensor (25 mA)

Bell/Siren (5 min)

NOTE: Up to 2 batteries may be connected in parallel to

obtain the desired standby (backup) time.

0.085 AH 0.085 AH 0.085 AH

Bell/Siren (15 min) 0.225 AH 0.225 AH 0.225 AH

* Bell/Siren current may be 0.7 – 1.0 A

Total AH Required

Self-resetting

circuit

Table 2 - AH Requirements

To S5053 LSM

or S5832SG

Control Panel

Determining Standby Battery Requirements

To calculate the size (AH rating) of your system's Backup

Battery, enter the Number (Qty) of devices of each type in

the chart above. Multiply the number of devices times the

AH rating for the desired backup period (Qty x AH = Total)

and enter the total in the last column. To determine the

total AH rating of the battery, add all values in the last

column.

C & K Model

1265 or 1270

C & K Model

1265 or 1270

Figure 4

Connecting two Batteries in Parallel

Total current from all sensors must be considered when

calculating AH rating. For example:

10 sensors @ 10 mA = 100 mA

Sierra Accessory Loading

Product Current Consumption

S5832SG Control Panel

S5010 Alpha Keypad

S5020 Icon Keypad

Max. Standby

125 mA

Max. Active

125 mA

50 mA

4 sensors @ 25 mA = 100 mA

Total current all sensors = 200 mA

30 mA

50 mA

S5030 LED Keypad

30 mA

100 mA (each)

50 mA

100 mA

AC Power

S5050 REMM (up to 2)

(Relay/Event Memory Module)

S5058 ZEM (up to 3)

(Zone Expansion Module)

S5070 Single-line Digital

Communicator

S5070-2 Dual-line Digital

Communicator

SN915-BUS RF Receiver

The Sierra S5832SG receives its power from a 16.5 VAC 40

VA transformer. Connect the transformer to the AC In termi-

nals on TB1 of the PCB (see Figure 1), using 18 AWG (1.02

mm) wire. (Some systems may have the transformer and

mains fuse block installed and pre-wired from the factory.)

40 mA (each)

35 mA

40 mA**

60 mA

35 mA

70 mA

Connect the AC transformer to an unswitched receptacle.

Do not share the secondary of the transformer with other

devices.

125 mA

170 mA

** ZEM VOUT Terminals can supply up to 300 mA (max.)

NOTE: AC input requirements may vary by country. Refer to

the Compliance section for additional wiring information.

Table 1 - Standby Battery Loading

Table 1 shows the current requirements for the Sierra

S5832SG control panel and accessories. Additional infor-

mation about Standby Battery requirements and Audible

times may be found in Table 2 - AH Requirements, at the top

of the next column.

Download from Www.Somanuals.com. All Manuals Search And Download.

Keypad Wiring (cont.)

Output Terminals

Figure 6, below, shows the connections for wiring the Sierra

Keypad to the Control Panel and connecting the optional

Terminate Exit Delay switch. Switch S1, in the lower right-

hand corner, is used for keypad addressing (see Table 5).

Table 3 shows the Output Terminals of the S5832SG, with

the Voltage and Current Range of each Output. The Table

also shows the maximum combined current for related out-

puts.

NOTE: If the keypad tampers are active (and programmed

in Block 3, Cmd Loc 044 - 045), tamper signals will be sent

to the control panel via the keypad bus. Keypad tamper

(hardwired keypads only) report routing is programmed in

Block 4, Cmd Loc 158. Keypad trouble conditions are also

reported on the keypad bus and the routing is defined in

Block 4, Cmd Loc 159.

Voltage

Range

Combined

Current

Function Terminal

Current

Comments

Specifically designed to

drive strobes with high

in-rush currents.

Typically used to drive

sirens mounted inside

the premises.

Supervised Siren Output

typically used to drive

bells, sirens, and other

high current devices

outside the premises.

Strobe

STROBE

Output

8.4 – 14.9 V

0.75 A

Internal

Siren

INT

SIREN

8.4 – 14.9 V

0.75 A

2.0 A

External

Siren

BELL+

BELL-

8.4 – 14.9 V

1.5 A

(3.0 A with

Battery)

Auxiliary

Power

Used to drive sensors,

etc.

AUX

8.4 – 14.9 V

1.0 A

0.3 A

Used to drive latching

devices like glassbreak

detectors or four-wire

smoke detectors that

must be reset.

Switched

Auxiliary

Power

SW AUX

Used to power keypads,

REMMs, ZEMs, and

SN915 RF Receiver.

Keypad

Power

KPWR

8.4 – 14.9 V

8.5 – 14.0 V

1.0 A

Optional Terminate

Exit Delay Switch

Zone 8

0.03 A

2-wire Smoke Detectors

Table 3

Output Terminal limits

Tamper Switch

External Bell Supervision

The circuit connection shown in Figure 5 is used only when

External Bell Line Super-

vision is required. For Bell

Line Supervision, the bell

must be equipped with an

internal diode.

9.X 2.2K Ohm

Figure 6

Connecting the Keypad Terminals

EOL

Sierra Accessory Wiring Distances

The Table shown below shows the maximum wiring dis-

tances for the Sierra accessories based upon total load cur-

rent drawn from each run. Refer to the Accessory Loading

Table on page 3 for load requirements.

To Bell Output Terminals

on Control Panel

Figure 5 - Bell Supervision Wiring

NOTE: Total wire distance for all devices combined not to

exceed 2440 M.

Keypad Wiring

Max Load 0.40 mm

0.51 mm

(24 AWG)

0.64 mm

(22 AWG)

0.81 mm

(20 AWG)

1.02 mm

(18 AWG)

1.29 mm

(16 AWG)

The Sierra S5832SG uses four terminals for powering and

communicating with the keypads and other devices via the

keypad data bus. The terminal connections are as follows:

per run

(mA)

(26 AWG)

(Ft.)

100

150

200

250

300

350

400

450

500

550

600

700

800

900

1000

121 (395) 192 (629)

60 (198) 96 (314)

40 (132) 64 (210)

305 (1000) 490 (1605) 774 (2538) 1225 (4016)

153 (500) 245 (803) 387 (1269) 612 (2008)

102 (333) 163 (535) 258 (846) 408 (1339)

76 (250) 122 (401) 194 (635) 306 (1004)

61 (200) 98 (321) 155 (508) 245 (803)

51 (167) 82 (268) 129 (423) 204 (669)

44 (143) 70 (229) 111 (363) 175 (574)

38 (125) 61 (201) 97 (317) 153 (502)

34 (111) 54 (178) 86 (282) 136 (446)

31 (100) 49 (161) 77 (254) 122 (402)

KPWR This terminal supplies +12 VDC to power the key-

pads or accessories.

KY+ One half of the differential keypad data bus. This

terminal combined with the KY- terminal provides

communication between the various devices and

the control panel.

30 (99)

24 (79)

20 (66)

17 (56)

15 (49)

13 (44)

12 (40)

11 (36)

10 (33)

48 (157)

38 (126)

32 (105)

27 (90)

24 (79)

21 (70)

19 (63)

17 (57)

16 (52)

14 (45)

12 (39)

10 (35)

KY-

Used in conjunction with the KY+ terminal for data

communications on the keypad data bus.

Common (ground) terminal for Power return.

28 (91)

25 (83)

22 (71)

19 (63)

17 (55)

15 (50)

45 (146) 70 (231) 111 (365)

41 (134) 65 (212) 102 (335)

35 (115) 55 (181) 87 (287)

31 (100) 48 (159) 77 (251)

(28)

(25)

(22)

(20)

TRMX Optional Terminate Exit Delay switch connected

between this terminal and C terminal. When active

(Block 7, CL 012), closing the exit delay switch will

short the TRMX terminal and skip all but the last 5

seconds of the exit delay.

27 (89)

24 (80)

43 (141) 68 (223)

39 (127) 61 (201)

(31)

Table 4

Maximum Wiring Distance for Sierra Accessories

Download from Www.Somanuals.com. All Manuals Search And Download.

The N.O. and N.C. zone configurations do not provide for

supervision of the detection devices.

Keypad Addressing

The S5832SG control panel will support up to 16 hardwired

keypads. Each keypad must have a different address, with

addresses ranging from 1 - 16. (Figure 6 shows the location

of the switch used to address the keypad.) Table 5 lists the

switch settings for S1 for each keypad address.

The following configurations provide supervision of the de-

tection devices:

EOL: This zone configuration uses a single EOL resistor to

detect the following conditions: Normal (2.2K), Fault (open

or short).

Addr

off

Addr

off

Supervised EOL: This zone configuration uses a single EOL

resistor to detect the following conditions: Normal (2.2K), Fault

(short), or Trouble (open).

Tamper: This zone configuration uses two EOL resistors to

detect four different zone conditions: Normal (2.2K), Fault

(4.4K), Trouble (short), or Tamper (open).

NOTE: For devices requiring a 10K Ohm EOL resistor,

use Zone 7 and remove jumper J5. (See page 1, Figure

1 for jumper location.)

Table 5

Keypad Addressing

Each keypad (Alphanumeric, Icon, or LED) may draw up to

50 mA of current. Once connected, the control panel will

automatically recognize the presence of the keypad.

On-Board Relay Terminals (TB2)

The Sierra S5832EB has a single-pole, double-throw (Form

C) relay mounted on the PCB. Connections to the relay are

made at TB2. (Refer to Figure 1 for relay terminal location.)

Connecting an Auxiliary Keypad (J8)

The S5832SG Control Panel also has a 4-pin Molex^®con-

nector (J8) for attaching an auxiliary keypad to the panel for

on-site programming. The connector (J8) is located on the

PCB above the Keypad Data Bus terminals (see Figure 6,

on page 4).

The on-board relay may be configured as Normally Open

(N.O.) or Normally Closed (N.C.) and can switch up to 1 A of

current at 12 VDC. For programming options, refer to Block 7,

Command Location (CL) 001.

The connections to J8 are as follows:

Accessories

Pin 1 Common (ground) for Power return.

Pin 2 Supplies +12 VDC to power the keypad.

Pin 3 KY+ on the differential keypad data bus.

Pin 4 KY– on the differential keypad data bus.

The Sierra S5832SG supports a variety of accessories which

communicate with the panel through the keypad data bus.

These accessories can include up to two Model S5050 Re-

lay/Event Memory Modules (REMM), up to three Model

S5058 Zone Expansion Modules (ZEM), and a Model SN915-

BUS SpreadNet^®RF Receiver.

Pins 1 and 2 supply power and ground, while pins 3 and 4

provide communication between the panel and the keypad.

Caution: When connecting accessories to the system,

use care not to exceed rated outputs. (See Table 1

on page 3 for Accessory loading information.)

Zone Terminals

The basic configuration of the S5832SG can support up

to 8 hardwired zones. Zone 8 is a powered loop for use

with two-wire smoke detectors. This loop is current-lim-

ited at 30 mA.

S5050 Relay/Event Memory Module

The Sierra S5832SG control panel will support up to two

Model S5050 REMMs connected to the keypad data bus.

NOTE: Trouble conditions and tampers, if enabled, are re-

ported via the keypad bus. Refer to Block 4, CL 158 and

159, respectively, for report routing information.

Power for the S5050 REMM is obtained by connecting the

KPWR terminal on the REMM PCB to either the KPWR or

AUX terminal on the control panel. For the power return,

connect the C terminal on the REMM to the C terminal on

the control panel. The GND terminal on the REMM PCB is

used to connect the REMM to Earth Ground.

c) EOL

End-of-Line

Resistor

d) EOL,

Supervised

e) 2x EOL

4-state

supervision

a) N.O.

Normally

Open

b) N.C.

Normally

Closed

Figure 7

Zone Configurations

Adding one REMM will increase Event Memory storage ca-

pability from 60 events to 250 events. Adding a second

REMM will increase the storage capacity to 500 events.

Zones may be configured with Normally Open (N.O.) or Nor-

mally Closed (N.C.) contacts (although not recommended).

Download from Www.Somanuals.com. All Manuals Search And Download.

The REMM also has five independently programmable re-

lays. The relay programming options are explained in the

programming summary, Block 7.

S5058 Zone Expansion Module

The Sierra S5832SG control panel has eight hardwired

zones and may be expanded up to 32 zones. Eight addi-

tional hardwire zones are obtained by connecting an

S5058 Zone Expansion Module to the keypad data bus.

Up to three S5058 ZEMs may be connected, providing a

total of 24 additional zones.

The AUX terminal on the S5050 REMM is capable of supply-

ing up to 100 mA of output current to power sensors and

other devices.

NOTE: Total combined current from the relays and AUX

NOTE: Trouble conditions and tampers, if enabled, are re-

ported via the keypad bus. The report routing is defined in

Block 4, CL 158 and 159, respectively.

output terminal may not exceed 100 mA.

Refer to the S5050 REMM Installation Instructions (P/

N 5-051-453-00) for additional information regarding the

set up, configuration, and operation of the S5050 REMM.

Power is supplied by connecting the KPWR terminal on

the S5058 ZEM PCB to the KPWR or AUX terminal on the

control panel and the C terminal on the ZEM to the C ter-

minal on the control panel. The GND terminal on the ZEM

PCB is for connecting earth ground to the ZEM.

There are two VOUT terminals (connected in parallel),

which can provide up to 300 mA of output current to power

sensors or other devices.

Each S5058 ZEM will support up to 8 hardwired zones. If

a zone is programmed as a SpreadNet zone (see Block

2, CL 111 - 142), it is not available for use as a hardwired

zone.

Figure 8

The S5050 Relay/Event Memory Module (REMM) PCB Layout

Additional setup and wiring information is available in the

S5058 Zone Expansion Module Installation Instruc-

tions (P/N 5-051-454-00).

Switch Settings

The S5050 REMM has five (5) dip switches (S1-1 thru S1-

4 and S2-1) which can be used to provide AUX power to

the relay outputs. The default setting for each switch is

“OFF.” In this position, each relay uses the switched (S)

and common (C) terminals. Each relay is independently

programmable by the installer.

With the switch in the ON position, the +12 VDC AUX

power is applied to the respective Relay switched (S) out-

put terminal (see Figure 9, below).

Switch Configuration

Figure 9, below, shows the relationship of the switches to

the relays on the REMM.

Figure 10

S5058 Zone Expansion Module (ZEM) PCB Layout

ZEM Addressing

S2-2 is used to address the REMM. Leave S2-2 in the ON

position for REMM #1. Change S2-2 to the OFF position

to address REMM #2.

S1-1 and S1-2 are used to address the ZEMs. The ZEM ad-

dress determines which zones are added to the S5832SG

control panel.

Figure 11, below, shows the switch settings to address the

ZEMs. ZEM #1 is used to add zones 9 - 16; ZEM #2 adds

zones 17 - 24; and ZEM #3 adds zones 25 - 32.

Switch

Relay

S1-1

S1-2

S1-3

S1-4

S2-1

R1S

R2S

R3S

R4S

R5S

S1-1 S1-2 S1-3 S1-4 S2-1 S2-2

S1-1

S1-2

Addr. S1-1 S1-2 Zones

off

9 - 16

17 - 24

25 - 32

Switch

REMM

S2-2

ON = REMM #1

OFF = REMM #2

Figure 11

Addressing the ZEM

Figure 9

REMM Switch Settings (shown in default position)

Download from Www.Somanuals.com. All Manuals Search And Download.

SN915-BUS SpreadNet Receiver

The SpreadNet SN915-BUS Bus Receiver connects to the

keypad bus and provides the communication link for all

SpreadNet keypads/keyfobs and zone transmitters.

Digital Communicator Connections

Removing/Installing the Digital Communicator

The digital communicator plugs into the control panel PCB

and is secured by a nylon retaining screw.

NOTE: Tamper and trouble conditions, if enabled, are re-

ported via the keypad bus. The report routing is specified in

Block 4, CL 158 and 159, respectively. Low Battery Report

Routing for the SpreadNet Transmitters is programmed in

Block 4, CL 157.

To remove the digital communicator:

1) Remove AC and DC power from the control panel.

2) Locate and remove the nylon screw. The screw is located

near the upper right-hand corner of the digital commu-

nicator PCB. (See page 1, Figure 1.) Use a #1 phillips

head screwdriver to remove the retaining screw.

3) Unplug the digital communicator from the control panel.

Power for the SN915-BUS may be supplied from either the

KPWR or AUX and C terminals on the control panel to the V+

and GND terminals on the SpreadNet Receiver (see Figure

12).

To install the digital communicator:

1) Ensure that AC and DC power have been removed from

the control panel.

2) Carefully plug the digital communicator into the control

panel PCB. Misalignment of the pins could damage the

control panel.

For additional information on wiring and configuration of the

SN915-BUS Receiver, refer to the SN915-BUS Installation

Instructions (P/N 5-051-440-00).

3) Replace the nylon retaining screw.

4) Apply power.

Digital Communicator Telephone Connections

Line #1

Figure 12

Connecting the SN915-BUS

SN990/991 SpreadNet Keypad/Remote

The control panel can support up to eight SpreadNet key-

pads. There are two different models available, the SN990-

KEYPAD and SN991-REMOTE. Both devices are battery

operated and communicate with the panel through the

SpreadNet SN915-BUS RF Receiver.

SpreadNet keypads provide one-way communication only

and do not display any panel status information.

Additional information on the SpreadNet keypad and remote

may be found in the SN990/991 Installation Instructions (P/N

5-051-556-00).

Figure 13

Telephone Connections

SN961 SpreadNet Keyfob

The Sierra S5832SG control panel can support either a one-

or two-line plug-on digital communicator.

The control panel can have up to eight SpreadNet keyfobs.

Each keyfob will be associated with a specific user number

and will arm, home arm, or disarm the system just like the

user code. The keyfob will communicate with the control panel

via the keypad bus.

The digital communicators have four terminals for connec-

tion to the telephone lines. These terminals are labelled:

Tip, Ring, T1, and R1. The single-line digital communicator

has one set of terminals and the dual-line digital communi-

cator has two sets of terminals. Figure 13 shows how to con-

nect the digital communicator to the incoming phone lines

and the house phones using either a single-line or a dual-

line digital communicator.

SpreadNet keyfob allows one-way communication only and

cannot display any panel status information.

For information on programming the SpreadNet keyfob, refer

to the SN900-PROG Operating Manual (P/N 5-051-136-00

Rev C or later).

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 14, below, shows the layout of the S5070SG-2 dual-

line digital communicator. The terminals for line 2 are la-

belled Tip, Ring, T2, and R2.

Remote Programming (RPS)

Remote Programming of the Sierra S5832SG control

panel is available with the Commander II software. The

remote programming session can be initiated locally from

the keypad or remotely by the Commander II software.

Setup for Direct Connect to the S5832SG

The procedure for initiating Direct Connect with your

model of Digital Communicator is outlined below.

1. When using Direct Connect, connect the telco cable

from the line side of the modem to the Tip and Ring

terminals on the Digital Communicator (Line 1 only).

2. Move the jumper (J6) to the enabled position, as shown

in Figure 15, below.

3. Start Commander II and open the Panel menu. Select

the Connect option and then click on Direct Connect.

Direct Connect

Disabled

Figure 14

S5070US-2 Dual-line digital communicator

Terminal Connections

Direct Connect

Enabled

Connect the Sierra S5832SG digital communicator to the

telephone line, as shown in Figure 13 (on previous page),

using an approved, 6 or 8 conductor telephone cable (not

included). Connect the cable to the control panel as follows:

Red = Ring

Green = Tip

Grey = Seized Ring (R1)

Brown = Seized Tip (T1)

Blue & Orange = Tamper

Yellow & Black = Not Used

Programming the Panel

Figure 15

The Sierra S5832SG control panel may be programmed

from any keypad connected to the keypad data bus. Con-

nector J8 (see Figure 1) is also available to temporarily con-

nect a keypad, if desired, for programming the panel. The

panel can also be programmed, either remotely or on-site,

using the Commander II software.

Direct Connect using the S5070SG Digital Communicator

4. Enable the Direct Connect jumper (see Figure 15) and

initiate the Direct Connect function in Commander II.

When you hear the modem tones, momentarily short

the Direct Connect pads located on the left-hand side

of the digital communicator PCB. You should hear the

seize relay energize to indicate connection.

The Command Locations used to store the programming

options of the Sierra S5832SG control panel are divided into

10 sections. Each section is called a Block. The configura-

tion of the control panel determines which Blocks are pro-

grammed.

5. Commander II should indicate that the connection has

been established. You are now ready to program the

panel.

6. Be sure to return the jumper to its original position

when the RPS session is completed.

All keypad programming is done from the Installer Program-

ming Mode. To enter the Installer Programming Mode, press

and hold the [1] key for 2 seconds.

Keypad Activated RPS

The following conditions must be met before starting a

keypad activated RPS session:

When programming with an Alphanumeric keypad, you must

select the appropriate language for your panel, followed by

the [Home] key. The icon and LED keypads do not require

the [Home] key to be pressed. On the LED keypad, all LEDs

are off to indicate that you must enter the installer code.

1. The RPS Phone Number must be programmed into

Block 4, CL 085 - 100;

2. Keypad RPS Enable (Block 4, CL 106) must be pro-

grammed for Yes (2);

Next, enter the 6-digit installer code. The default installer

code is [0-1-2-3-4-5]. On the Alphanumeric keypad, press

the [Home] key to use Menu Programming or the [Bypass]

key to use Quick Programming. You are now in installer pro-

gramming mode.

3. RPS/Modem Types (Block 4, CL 107) must match the

configuration of the Commander II software;

4. The phone lines must be connected to the Tip and Ring

terminals on the digital communicator (Line 1 only);

and

To exit the Installer Programming Mode, press and hold the

[CANCEL] key for 2 seconds. This will exit the programming

mode and reset the panel.

Download from Www.Somanuals.com. All Manuals Search And Download.

Keypad Activated RPS (cont.)

Programming With an LED Keypad (cont.)

Cmd Loc 005

(flashing)

5. Commander II must be running at the remote site.

Block

(steady)

If the above conditions are met, you are now ready to ini-

tiate the RPS session from an Alphanumeric keypad.

1. Using an Alphanumeric Keypad, enter the Installer

Mode Programming (see Programming With an Alpha-

numeric Keypad on page 10). Select the Menu Pro-

gramming Mode and go to Block 0 (Installer

Commands). Press the [Home] key to accept.

Program Data

(steady)

Figure 18

Reading Programming Data on the LED Keypad

There are three keys used to access and enter data into the

control panel from the keypad. They are the [Bypass],

[Home], and [Cancel] keys. The function of each key is ex-

plained in the next column.

Figure 16

Accessing Installer Commands (Block 0)

Key

Function

2. Scroll through the options, using the [Bypass] key until

you get to the RPS Callback? option (option 10).

[Bypass] Moves the cursor between the Block, Com-

mand Location (Cmd Loc), and Data fields.

Press the [Bypass] key a fourth time to return

the cursor to the Cmd Loc field.

[Home]

This key has several functions, depending

upon the field being edited and the data en-

tered at the keypad.

Figure 17

Activating Keypad RPS

If the Cmd Loc field is active, press the [Home]

key to increment to the next Loc. You may also

enter a new Cmd Loc and press the [Home]

key to move to that Loc. The LEDs for zones 9

- 16 display will show the data stored in the

new Loc.

3. Press [Home] to activate the RPS feature.

Programming With an LED Keypad

You may use an LED keypad to program the control panel.

The LED display on the keypad is used to display all pro-

gramming information: Block Number, Command Location,

and Data. The Block Number is displayed using the Power,

Arm, Ready, and Service LEDs. Command Locations are dis-

played using the LEDs for zones 1 - 8. The LEDs represent-

ing zones 9 - 16 are used to display the program data. Table

6, below, lists the relative value for each LED.

If the Data field is active, pressing the [Home]

key will write the data in the display to the Cmd

Loc indicated. The system will also be incre-

mented to the next Cmd Loc. The Data field

will remain active.

If the Block field is active, press the [Home]

key to increment to the next Block and reset

the Cmd Loc to 001. You may also enter the

number of the desired Block (1 - 10 or 0 - 10

for the Alphanumeric keypad), followed by the

[Home] key to go to that Block.

Upon entering the installer programming mode, all LEDs

will be off. The installer must then enter the installer code

[0-1-2-3-4-5]. The system will then go to Block 1, Command

Location 001 and display the data stored at that location.

The LEDs in the currently active field will blink (if any are lit)

indicating that the data may be edited.

[Cancel] The [Cancel] key allows you to undo changes

to the programming, provided you have not

stored the data. Once the data has been writ-

ten to memory (by pressing the [Home] key),

you cannot use the [Cancel] key to recover the

original data.

Block Numbers

Zone LEDs

Cmd Loc Data

LED

Value

Service

Ready

Arm

If the data has not been changed and the Cmd

Loc field is active, pressing the [Cancel] key

will decrement to the previous Cmd Loc. If the

Block field is active, pressing the [Cancel] key

will decrement to the previous Block.

Power

128

CAUTION: Pressing and holding the [Cancel] key for 2

seconds will Exit Programming Mode.

Table 6

Reading the LEDs

Download from Www.Somanuals.com. All Manuals Search And Download.

Programming With an Alpha Keypad (cont.)

Programming With an Alpha Keypad

Upon entering the installer programming mode, the display

will ask you which language you wish to use for program-

ming the panel. Each panel supports three languages, one

of which is English. The other languages are determined by

the model number of the panel. The Alphanumeric keypad

provides two panel programming options: Quick or Menu

programming. Both options use a combination of text and

numbers in the LCD display.

Key

Function

[Bypass] Used to scroll through the different Menu op-

tions and levels.

[Home] If the PRG> prompt is displayed, this key will

write the data currently displayed to memory

and increment to the next program position.

If the Menu has additional options in sub-

menus, this key will move to the next sub-

menu.

[Cancel] Cancel the operation, if the data has not been

written to memory. If you are in a sub-menu,

this key will back up one level.

Figure 19

Selecting the Language on the Alphanumeric Keypad

CAUTION: Pressing and holding the Cancel key for 2

seconds will Exit Programming Mode.

Once a valid installer code has been entered, the installer

has the option of using either the Quick or Menu Program-

ming mode to enter data into the panel. Each method is

explained below.

Programming With an Icon Keypad

The display on the keypad consists of a 3-digit display for

showing numbers (Blocks, Cmd Locs, and Data) and fixed

text for indicating the type of data displayed.

Figure 20

Selecting the Programming Mode with the Alphanumeric Keypad

Figure 22

Quick Programming Mode

Reading Command Location on the Icon Keypad

Using the Quick Programming mode, you can easily go

directly to any Cmd Loc (Blocks 1 - 10 only; the Installer

Commands, Block 0, are not available in Quick program-

ming mode). This allows you to view or edit any of the

data programmed into the panel.

Figure 23

The Alphanumeric display will show the Block Number (1

- 10) and Programmed Data (varies by location) on the

top line of the display, with the Command Location (var-

ies by Block) shown on the bottom line.

Displaying Block Data on the Icon Keypad

Data will be displayed using only the digits required.

Figure 24

Figure 21

Viewing Program Data on the Icon Keypad

Reading Programming Data on the Alphanumeric Keypad

The [Bypass], [Home], and [Cancel] keys are used to move

between fields and to edit the data in each field, as outlined

previously.

The [Bypass], [Home], and [Cancel] keys are used to

move between fields and to edit the data in each field, as

outlined previously.

Menu Programming Mode

The Menu Programming mode uses menu options and

descriptions to guide you easily through the panel pro-

gramming. You can scroll through the Blocks by press-

ing the [Bypass] key or go directly to any Block by press-

ing the desired key (0 - 10), followed by the [Home] key.

The same three keys ([Bypass], [Home], and [Cancel])

are used in the Menu Programming mode, with slight

variations.

Download from Www.Somanuals.com. All Manuals Search And Download.

Event Memory Codes

Event

Installer Mode Options, (Block 0)

There are 10 Installer Mode Options which are available

from the Menu mode. These options allow the installer to test

the various aspects of the system's operation, program the

Custom Messages used by the Alphanumeric keypads, and

start keypad activated RPS.

Code

Description

Zone is/was in alarm

Zone is/was tampered

Zone is/was in trouble

Zone alarm/tamper restored

Zone has been bypassed

To access the Block 0 Commands, press and hold the [1] key

for 2 seconds. Use the [Home] and [Bypass] keys to select

the desired language. When prompted, enter your [Installer

Code]. Then press the [Home] key to select Menu mode.

Upon entering the Menu mode, pressing either [0] or [By-

pass] will take you to the first of the Block 0 options.

Zone Unbypassed

Area X disarmed by User Y

Area X armed by User Y

User Walk-test started

User Walk-test completed

Alarm in Area X canceled by User Y

Comm Fail Receiver X

Comm Fail restore Receiver X

AC power fail

AC power restored

Low Battery (Control Panel)

Low Battery restored (Control Panel)

Master User changed User Code Y

Primary phone line cut

Primary phone line cut restored

Secondary phone line cut

Secondary phone line cut restored

Emergency/medical alarm (hard or soft zone)

Emergency/medical alarm restored (hard / soft)

Panic/police alarm (hard or soft zone)

Panic/police alarm restore (hard / soft)

Fire alarm (hard or soft zone)

Fire alarm restore (hard / soft)

Begin Installer Programming (local)

Installer Programming completed (local)

Supervisory failure Zone X (SpreadNet)

Supervisory failure restore Zone X (SpreadNet)

Low Battery Zone X (SpreadNet)

Low Battery restore Zone X (SpreadNet)

Watchdog reset (panel reset)

Bell failure (Siren loop open or short)

Bell failure restored

Installer Walk-Test

The first option available from the Block 0 Commands is the

Walk-Test? option. To use this option, press [Home]. To pro-

ceed to the next option, press [Bypass].

After installation, the installer can perform a system Walk-

Test. Using this option, the installer can test the operation of

each zone in the system.

While in the Installer Walk-Test Mode, the zones faulted dur-

ing the current Walk-Test session will be annunciated at the

keypad and continuously displayed. This memory will be

purged when exiting Walk-Test Mode.

Event Memory

The second Block 0 Command available is Event Memory.

Press [Home] to access the Event Memory option or [By-

pass] to scroll to the next option.

After selecting Event Memory?, the display will ask if you

wish to Display Event Memory. To display the contents of

the Event Memory, press [Home]. If you wish to Erase Event

Memory, press [Bypass], then press [Home].

Event Memory stores all events which have occurred since

the panel was initially installed or the memory was last

cleared. The Sierra S5832SG control panel has an internal

Event Memory capable of storing up to 60 events with time

and date stamping. By adding the Relay/Event Memory Mod-

ule, the memory capability may be expanded to either 250

events (1 module) or 500 events (2 modules).

Exit fail, Zone X still faulted at end of Exit Delay

Duress code entered for Area X

Kidwatch open failure (Kidwatch time expired)

Begin RPS programming

Events are viewed in chronological order (oldest to newest)

by pressing the [1] key. Events may be viewed in reverse

order (newest to oldest) by pressing the [4] key.

RPS connection failure

Table 7 shows the Event Codes displayed by the LED and

Icon keypads. The event codes are displayed using the zone

LEDs (LED keypad) or the 3-digit display (Icon keypad). The

Sierra Reference Manual contains additional information on

reading the codes with the LED keypad. The events are listed

in numerical order.

RPS programming successful

Test Report (manual or automatic)

Trouble Zone X restored

User Y override of Auto Arming

Tamper Zone X restored

Ground Fault

Ground Fault restored

Brown Out

Brown Out restored

Peripheral communications trouble

Peripheral communications trouble restored

Table 7

Event Memory Codes

Download from Www.Somanuals.com. All Manuals Search And Download.

Custom Messages

Alphanumeric keypads have the ability to display custom-

ized messages. These messages are stored in the control

panel's nonvolatile memory.

Test Report

Following the Custom Messages option is the Send Test

Report option. Selecting this option will initiate a Test Re-

port to the Central Station. The keypad will display a mes-

sage indicating the success or failure of the Report.

To program the Custom Messages, use the [Bypass] key to

scroll to the Custom Messages? screen. Press the [Home]

key to display the first Custom Message (EDIT TROUBLE

MSG).

Test Report with Audibles

This option generates a Test Report to the Central Sta-

tion with all local audibles (internal and external sirens)

sounding for the duration of the Test Report attempt.

Pressing any key during the Test Report period will turn

the sirens off. The system will provide feedback to con-

firm the success or failure of the Report.

There are 41 Custom Messages available. The Edit Trouble

Message, 32 Zone Messages, and 8 Area Messages.

To assist you in entering the Custom Messages, a program-

ming template is included with the keypad. The template

is shown below and the operation of the keys is described

at the top of the next page.

Audible Test

This option turns on all local audibles (internal and exter-

nal sirens) for a period of 5 seconds.

Entry Delay Test

Using this option, the installer can test the Entry Delay to

ensure that a user has sufficient time to enter the pre-

mises and disarm the system without generating an alarm.

To begin the test, scroll to the Entry Delay Tst screen

and press [Home]. Then fault the Entry zone to begin the

delay.

Exit Delay Test

Using this option, the installer can test the Exit Delay to

ensure that a user has sufficient time to arm the system

and leave the premises without generating an alarm. To

begin the test, scroll to the Exit Delay Test screen and

press [Home]. The Exit delay will begin immediately.

Bypass

Home CANCEL

Figure 25

The Alphanumeric Keypad Programming Template

Transmit Walk-Test Queue Reports

Walk-Test events stored in Event Memory during the cur-

rent session will be transmitted to the Central Station.

The system will provide feedback to confirm the success

or failure of the Report.

To enter a Message or Label, use the following key com-

mands:

Key

[2]

[8]

[4]

[6]

Function

Scroll forward through characters/symbols

Scroll backward through characters/symbols

Move cursor left one character

Move cursor right one character

RPS Callback

Using this option, the installer can initiate an RPS ses-

sion from the Keypad.

[Cancel] Cancel current changes and restore pre-

vious message, or scroll up one message

[Home] Write message to memory and scroll down

one message

Battery Test

This option allows the installer to perform a Battery Test

on the system. The test starts when you press the [Home]

key. The system will exit the installer programming mode

and reset the panel. The test takes approximately two min-

utes to complete. The battery status will be displayed only

if a Low Battery condition exists.

In addition, other numbers on the keypad enable you to

quickly move to special places in the alphabet. These

special keys are:

[1]

[3]

[7]

[9]

Jump to the space character

Jump to the number 0

Jump to the letter A

Jump to the letter a

NOTE: The [Cancel] key will only restore previous mes-

sages if the message has not been written to

memory using the [Home] key.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programming Summary - Sierra Model S5832SG

Block 1 - Code Option Programming

This programming block is divided into 80 Command Locations (CL 001 - 080). This Block used to program the Installer’s

Code (001-006), Default Installer Code on Power Up (007), Require Installer Code for Direct Connect via RPS (008), and to

set up the User Code parameters. The parameters include setting Maid Code, Duress, and Kidwatch.

Comments

Installer Code

This is a 6-digit code which is required to allow access to installer program-

ming mode. The code is programmed 1 digit per Cmd Loc.

Cmd Loc 001

002 003 004

005 006

Default

Range

0 - 9 0 - 9 0 - 9 0 - 9 0 - 9 0 - 9

Default Installer Code on Power Up?

Comments

Options:

Cmd Loc 007

If enabled (programmed as 2), this restores the Installer

Code to the default value (see CL 001 - 006) following a

power failure/restoral.

Default

Range

1 - 2

Yes

Installer Code Required on Direct Connect RPS?

Comments

Options:

Cmd Loc 008

If enabled, the Installer Code (CL 001 - 006) is required

when programming the panel with the direct connect RPS

function of COMMANDER II.

Default

Range

1 - 2

Yes

Options:

Maid Code Enable (by Area)

Comments

Disabled

Saturday

Friday

Thursday

Wednesday

Cmd Loc 009 010 011 012 013 014 015 016

The Maid Code may be specified by active days of

the week and by individual areas. Area 1 may also

use keypad activation for temporary access.

Default

Area

Range

0 - 255 (CL 009)

0 - 127 (CL 010 - 016)

NOTE: Maid Code Enable programming deter-

mines when the Maid Code may be used for disarm-

ing the system. The Maid code is always available to

arm the system.

16 Tuesday

32 Monday

64 Sunday

128 By Keypad

Maid Code Hours, Temporary Access, Area 1

Comments

Cmd Loc 017

This option is used in conjunction with keypad activation of the Maid Code

for area 1 only. Duration of the active period is from the time of activation by

grand master user (user #1) or area master (user #12). To disable keypad

(temporary) activation, program this location with 0.

Default

Range

0 - 254

Comments

Duress Code Enable (By Area)

Options:

If the system is divided into areas, this option deter-

mines if the duress code associated with a specific

area is active. Refer to the Sierra S5090 Reference

Manual (P/N 5-051-528-01), Block 9 programming

for details on assigning user codes to areas.

Cmd Loc 018

Disabled

Default

Range

Area 1

Area 2

Area 3

Area 4

0 - 255

16 Area 5

32 Area 6

64 Area 7

128 Area 8

Kidwatch Enable

Comments

Options:

Cmd Loc 019

If used, this option must be enabled (program

value > 128) and have the appropriate days of

the week programmed. The Kidwatch timer is

programmed from Block 6, CL 006 - 009. The

same start and end times are used for all days

when the Kidwatch feature is active.

Disabled

Saturday

Friday

Thursday

Wednesday

Default

Range

0, 129 - 255

16 Tuesday

32 Monday

64 Sunday

NOTE: If enabled, the Kidwatch code must be

entered if Area 1 is armed during the Kidwatch

window (see Block 6, CL 006 - 009).

128 Enable (Master)

Keypad Lockout Enable

Comments

Options:

Cmd Loc 020

If enabled, 10 consecutive keystrokes without pro-

ducing a valid user code will cause a keypad

delay starting at 15 seconds and doubling each

time up to a maximum of 240 seconds (4 min).

Disabled

Default

Range

1 - 3

When Disarmed

Always Active

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 1 - Code Option Programming (cont.)

User Code Privileges (User # 1 - 60)

Comments

Options:

Cmd Loc 021 022 023 024 025 026 027 028

These programming Options determine which

Options the user is authorized to perform.

Some user codes may have alternate func-

tions. (See Block 9 - Partition Programming

in the Sierra Reference Manual for additional

information.)

Limited Functions**

User #

Cmd Loc 029 030 031 032 033 034 035 036

User # 10 11 12 13 14 15 16

Cmd Loc 037 038 039 040 041 042 043 044

User # 17 18 19 20 21 22 23 24

Cmd Loc 045 046 047 048 049 050 051 052

User # 25 26 27 28 29 30 31 32

Cmd Loc 053 054 055 056 057 058 059 060

User # 33 34 35 36 37 38 39 40

Cmd Loc 061 062 063 064 065 066 067 068

User # 41 42 43 44 45 46 47 48

Cmd Loc 069 070 071 072 073 074 075 076

User # 49 50 51 52 53 54 55 56

Cmd Loc 077 078 079 080

Disarm

Arm

Bypass

Open/Close Rpt

16 Lang. Code opt. 1

32 Lang. Code opt. 2

Language

English

Spanish

Italian

Program Value

** Limited Functions are user number specific.

They may include relay operation, restricted

SN device operation, and some end-user

functions.

User #

Default

15 (All CL)

Range 0 - 47 (All CL)

Block 2 - Zone Configuration Programming

Block 2 is divided into 160 Command Locations (CL 001 - 160) which are used to program the characteristics of each of the zones

in the control panel. The features include Delay Times, Zone Type, Zone Restoral Type, Zone Response Time, Audible Cadence,

Circuit Type, Chime Enable, Shunt Enable, and Home Arm Shunt List. The soft zone programming uses CL 155 - 160.

Entry Delay #1

Comments

Cmd Loc 001

This establishes the first of two delay times for entry zones. Time is entered

in seconds.

Default

Range

10 - 255 (Seconds)

Comments

Entry Delay #2

This establishes the second of two delay times for entry zones. Time is

entered in seconds.

Cmd Loc 002

Default

Range

10 - 255 (Seconds)

Exit Delay

Comments

Cmd Loc 003

This establishes the delay time for exit zones. The time programmed into

this location should allow the user to use the exit farthest from the keypad.

Time is entered in seconds.

Default

Range

20 - 255 (Seconds)

Comments

Options:

Zone Type (Zones 1 - 32)

These programming

Options determine the

zone type for each zone

(hardwired or wireless)

in the system.

Day Bell/Inst

Day Bell/Delay

Disabled

Cmd Loc 004 005 006 007 008 009 010 011

Entry Delay 1/Exit

Entry Delay 2/Exit

Interior Instant

Interior Delay 2

Instant (Perim.)

Day Buzzer/Inst

Day Buzzer/Delay

Zone #

Default

10 24-Hr. BA

11 Fire (FA)

12 Tamper

13 Panic/Hold-Up

14 Emergency-Med

15 Keyswitch **

Cmd Loc 012 013 014 015 016 017 018 019

Zone # 10 11 12 13 14 15 16

Cmd Loc 020 021 022 023 024 025 026 027

Zone # 17 18 19 20 21 22 23 24

Cmd Loc 028 029 030 031 032 033 034 035

Zone #

Default

Range

29 30 31

** If the Zone Type is programmed as Keyswitch, then Zone Restoral

Type (Block 2, CL 036 - 067) will be programmed using Option #2

values.

0 (CL 012 - 035)

0 - 15 (All CL)

Zone Restoral Type (Zones 1 - 32)

Option Set #1

Comments

Option Set #2

Cmd Loc 036 037 038 039 040 041 042 043

Zone #

Cmd Loc 044 045 046 047 048 049 050 051

Zone # 10 11 12 13 14 15 16

Cmd Loc 052 053 054 055 056 057 058 059

Zone # 17 18 19 20 21 22 23 24

Cmd Loc 060 061 062 063 064 065 066 067

Disabled

Option #1 values are

used for all zone types

except Keyswitch.

Disabled

Arm/Disarm

Arm Only

Disarm Only

N/A

Return to normal

and bell silenced

Return to normal

and not armed

User code entry

(zone may remain

faulted)

Keyswitch zones will

use the second set of

Options. Default value

for keyswitch is

(Arm/Disarm).

Zone #

Default

Range

2 (All CL)

1 - 5 (All CL)

29 30 31

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 2 - Zone Configuration Programming (cont.)

Options:

Zone Response Time (Zones 1 - 8)

Comments

250 mS

500 mS

Cmd Loc 068 069 070 071 072 073 074 075

These Options select the zone response time (in mil-

liseconds) of zones 1 - 8 and zones available from

the S5058 Zone Expansion Module.

Zone #

Cmd Loc

Zone #

Cmd Loc

Zone #

Cmd Loc

Zone #

Default

076

(Zone Expander Module #1)

(Zone Expander Module #2)

(Zone Expander Module #3)

9 thru 16

077

17 thru 24

078

25 thru 32

2 (All CL)

All zones on the S5058 ZEM use the same re-

sponse time.

Range

1 - 2 (All CL)

Audible Cadence (Zones 1 - 32)

Comments

Options:

Cmd Loc 079 080 081 082 083 084 085 086

These options program the opera-

Keypad Buzzer

Zone #

Cmd Loc 087 088 089 090 091 092 093 094

Zone # 10 11 12 13 14 15 16

Cmd Loc 095 096 097 098 099 100 101 102

Zone # 17 18 19 20 21 22 23 24

Cmd Loc 103 104 105 106 107 108 109 110

tion of the internal and external

sounders. Both internal and exter-

nal sounders will operate together.

Programming options 5 and 6 also

limit the duration of the sounder

outputs.

Pulsing Sounder (1.5s on/off)

Steady Sounder

Temporal Code 3 (0.5s on/

0.5s off 2x, 0.5s on/ 1.5s off)

On 1 Min./Off 30s

(repeated twice)

Zone #

Default

Range

3 (All CL)

1 - 7 (All CL)

27 28 29 30 31 32

On 1 Min./Off 30s

(repeated 5x)

Silent

Exceptions are: Keyswitch/Spread-

Net Arming Annunciation (Block 3,

CL 051) and Ringback (Block 4,

CL 115).

Zone Circuit Type (Zones 1 - 32)

Comments

Options:

Cmd Loc 111 112 113 114 115 116 117 118

Tamper zones use 2 EOL resistors and may

detect 4 discreet conditions (normal, fault/

alarm, trouble, and tamper).

Normally Closed

Normally Open

EOL

Supervised EOL

Tamper (2 EOL)

SpreadNet RF

Zone #

Cmd Loc 119 120 121 122 123 124 125 126

Zone # 10 11 12 13 14 15 16

Cmd Loc 127 128 129 130 131 132 133 134

Zone # 17 18 19 20 21 22 23 24

Cmd Loc 135 136 137 138 139 140 141 142

If any zone is designated as a SpreadNet

zone, it will automatically be ignored as a

hardwired zone.

For devices requiring 10K EOL resistor, use zone 7 and remove J5. Refer

to the S5090 Sierra Reference Manual for additional information.

Zone #

Default

Range

3 (All CL)

1 - 6 (All CL)

28 29 30 31

Chime Enable

Comments

Options:

If programmed for chime, these zones will

sound at the keypad when the control panel

is disarmed and the zone is faulted. It is used

for delay, interior, and instant zones only. The

program value is a total of all zones in the

group which will have Chime enabled.

Disabled

Zone 1

Zone 2 10 18 26

Zone 3 11 19 27

Zone 4 12 20 28

Zones:

Cmd Loc

Default

Range

1 - 8

143

9 - 16 17 - 24

25 - 32

146

17 25

144

145

0 - 255

0 - 255 0 - 255

0 - 255

16 Zone 5 13 21 29

32 Zone 6 14 22 30

64 Zone 7 15 23 31

128 Zone 8 16 24 32

Zone Bypass Enable

Options:

Comments

Disabled

Zone 1

Zone 2 10 18 26

Zone 3 11 19 27

Zone 4 12 20 28

Zones:

Cmd Loc

Default

Range

1 - 8

9 - 16 17 - 24

148

255

25 - 32

150

255

These four command locations determine

which zones a user may manually bypass (if

authorized in Block 1, CL 021 - 080).

17 25

147

149

255

0 - 255

255

0 - 255 0 - 255

0 - 255

Zone bypass enable is divided into groups

of 8 zones each. The program value is a total

of all zones in the group which may be by-

passed.

16 Zone 5 13 21 29

32 Zone 6 14 22 30

64 Zone 7 15 23 31

128 Zone 8 16 24 32

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 2 - Zone Configuration Programming (cont.)

Comments

Home Arm Bypass List

Options:

These four (4) command locations determine

which zones will be automatically bypassed

when the user home arms the system.

Disabled

Zone 1

Zone 2 10 18 26

Zone 3 11 19 27

Zone 4 12 20 28

Zones:

Cmd Loc

Default

Range

1 - 8

151

9 - 16 17 - 24

152

25 - 32

154

17 25

153

0 - 255

0 - 255 0 - 255

0 - 255

The home arm bypass list is divided into

groups of 8 zones each. The value entered is

the total of all zones in the group to be auto-

matically bypassed.

16 Zone 5 13 21 29

32 Zone 6 14 22 30

64 Zone 7 15 23 31

128 Zone 8 16 24 32

Comments

Soft Zone Enable (Medical, Police, and Fire)

Options:

If enabled, press and hold any of the soft zone keys for two

seconds to report an alarm condition (see also Block 4, CL

148 (Report Routing)). The local sounder (Block 2, CL 158 -

160) will also be activated.

Key:

Med

155

Police

Fire

157

Cmd Loc

Default

Range

156

Yes

1 - 2

Comments

Options:

Soft Zone Audible Cadence

These Options program the opera-

tion of the internal and external

sounders in response to the Medi-

cal, Police, and Fire (soft zone)

keys. Both internal and external

sounders will operate together. Pro-

gramming Options 5 and 6 also limit

the duration of the sounder out-

puts.

Key:

Med

158

Police

Fire

160

Keypad Buzzer

Pulsing Sounder (1.5S on/off)

Steady Sounder

Temporal Code 3 (0.5S on/

0.5S off 2x, 0.5 S on/ 1.5 S off)

On 1 Min./ Off 30S

(repeated twice)

Cmd Loc

Default

Range

159

1 - 7

On 1 Min./ Off 30S

(repeated 5x)

Silent

Block 3 - Armed System Programming

This Block is divided into 54 Command Locations (CL 001 - 054). This Block allows the installer to set the Arming Type, Enable

Autohome, and set the three Quick functions. In addition, the Installer can select the Keypad functions, Cross-Zoning and

Double-Knock functions, Auto Arming and Disarming, and other miscellaneous functions.

Options:

Arming Type

Comments

Goof-Proof

Cmd Loc 001

This option determines the conditions necessary

in order to arm the system (zone status, etc.).

For additional details on arming options, refer to

the S5090 Reference Manual.

Force Arming

Chirp-Alert

Default

Range

1 - 3

Autohome Enable

Comments

Options:

Cmd Loc 002

If enabled, arming the system without exiting the premises

will cause the system to automatically home arm (bypass all

zones programmed in Block 2, CL 151 - 154). Perimeter

zones will be armed with all delays active.

Default

Range

1 - 2

Yes

Comments

Options:

Quick Arming Enable

Cmd Loc 003

If enabled, quick arming allows the user to arm the system

without entering a user code. Quick arming pertains to full

arming, home arming, and instant arming. System delays

programmed for those functions will be in effect. (See the

S5090 Reference Manual for details on arming features.)

Yes

Default

Range

1 - 2

Comments

SpreadNet Single Button Disarming Enable

Options:

If enabled, allows the system to be disarmed using the “Dis-

arm” button on a SpreadNet SN991-REMOTE or SN961-

KEYFOB. With this option enabled, the “Door” button on the

SN991-REMOTE or SN990-KEYPAD may also be used to

activate a relay (see Block 7, CL 001 - 011, option 2).

Cmd Loc 004

Default

Range

1 - 2

Yes

Quick Exit Enable

Comments

Options:

Cmd Loc 005

If enabled, quick exit allows the user to Home arm the sys-

tem and then leave the premises at a later time, without the

need to disarm and re-arm the system. Pressing and hold-

ing the [Home] key for two seconds will invoke the quick exit

function.

Default

Range

1 - 2

Yes

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 3 - Armed System Programming (cont.)

Quick Bypass Enable

Comments

Options:

Cmd Loc 006

If enabled, quick bypass allows any user to bypass zones

without entering a user code. To bypass a zone, press the

[Bypass] key followed by the 2-digit code for the zone to be

bypassed.

Default

Range

1 - 2

Yes

Comments

Options:

Home Arm Exit Delay Enable

If enabled, the exit delay (Block 2, CL 003) will start when a

user presses and holds the [Home] key for two seconds. If

disabled, the exit delay will be ignored and the system will

home arm instantly.

Cmd Loc 007

Yes

Default

Range

1 - 2

4X Exit Delay Extension Enable

Comments

Options:

Cmd Loc 008

If enabled, the exit delay (Block 2, CL 003) will restart if the

delay zone is faulted a second or subsequent time during

the exit delay. The exit delay may be restarted up to 4 times.

Default

Range

1 - 2

Yes

Chirp-Alert on Exit Fail

Comments

Options:

Cmd Loc 009

If enabled, all sounders (internal and external) will chirp for

three seconds at the start of the entry delay (Block 2, CL

001 or 002).

Default

Range

1 - 2

Yes

Low Battery Arming

Options:

Comments

Cmd Loc 010

If enabled, allows the system to be armed even if the back-

up battery is low.

Default

Range

1 - 2

Yes

Keypad Buzzer During Exit Delay

Comments

Options:

Cmd Loc 011

If enabled, the keypad buzzer sounds during the exit delay.

The keypad buzzer rate is faster during the last 10 seconds

of the exit delay.

Default

Range

1 - 2

Yes

Comments

Options:

Keypad Buzzer During Entry Delay

If enabled, the keypad buzzer sounds during the entry de-

lay. The keypad buzzer rate is faster during the last 10

seconds of the entry delay.

Cmd Loc 012

Yes

Default

Range

1 - 2

Comments

Options:

Keypad LED Status

This option controls the zone

and status displays of the

LED keypad.

Always display arm and zone status

Status always on while disarmed. If

armed, status displayed for 30 secs.

Display arm and zone status for 30

seconds following User Code entry.

Cmd Loc 013

Default

Range

1 - 3

NOTE: The Power and Arm

LEDs on all keypads oper-

ate the same.

Options:

Comments

Cross-Zoning List

If programmed for cross-zoning, any two

of the zones listed here must be violated

while armed in order for an alarm condition

to register.

Disabled

Zone 1

Zone 2 10 18 26

Zone 3 11 19 27

Zone 4 12 20 28

Zones:

Cmd Loc

Default

Range

1 - 8

014

9 - 16 17 - 24

25 - 32

017

17 25

015

016

0 - 255

0 - 255 0 - 255

0 - 255

If the system is divided into areas, both

zones in alarm must be within the same area.

16 Zone 5 13 21 29

32 Zone 6 14 22 30

64 Zone 7 15 23 31

NOTE: Fire, delay, and keyswitch zones

are ignored if placed on the cross-zone list. 128 Zone 8 16 24 32

Double-Knock List

Comments

Options:

Zones listed here must be violated twice

(or any two zones must be faulted) within

a 30-second period in order for an alarm

condition to register.

Disabled

Zone 1

Zone 2 10 18 26

Zone 3 11 19 27

Zone 4 12 20 28

Zones:

Cmd Loc

Default

Range

1 - 8

9 - 16 17 - 24

25 - 32

021

17 25

018

019

020

0 - 255

0 - 255 0 - 255

0 - 255

If the system is divided into areas, the

alarms must be within the same area.

16 Zone 5 13 21 29

32 Zone 6 14 22 30

64 Zone 7 15 23 31

128 Zone 8 16 24 32

NOTE: Fire, delay, and keyswitch zones

are ignored if placed on this list.

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 3 - Armed System Programming (cont.)

Auto-Arming Enable (Area)

Comments

Options:

Cmd Loc 022

Auto-Arming may be enabled for any or all partitions. If

enabled, the system will be automatically armed each

day at the time specified in Block 3, CL 023 and 024. All

partitions will auto-arm using the same timer.

Disabled

Default

Range

Area 1

Area 2

Area 3

Area 4

0 - 255

Auto-Arming Time (Hours)

Cmd Loc 023

When programming the time of day for auto-arming,

use the 24-hour format. (Add 12 hours for afternoon

and evening times.)

16 Area 5

32 Area 6

64 Area 7

128 Area 8

Default

Range

0 - 23

The internal sounder will sound a warning two min-

utes and again at one minute prior to the Automatic

Arming of the system.

Auto-Arming Time (Minutes)

Cmd Loc 024

Default

Range

0 - 59

Auto-Disarming Enable (Area)

Comments

Options:

Cmd Loc 025

This will automatically disarm the partitions indicated

according to the information programmed into Block

3, CL 026 - 028. The value programmed is a total of all

areas to auto-disarm within the system.

Disabled

Area 1

Area 2

Area 3

Area 4

Default

Range

0 - 255

16 Area 5

32 Area 6

64 Area 7

128 Area 8

Auto-Disarming Enable (Day of Week)

Comments

Options:

Cmd Loc 026

This will automatically disarm the areas specified

in Block 3, CL 025. Auto-disarm will occur on the

days programmed (Block 3, CL 026) and at the

time specified (Block 3, CL 027 - 028). The value

programmed in Block 3, CL 026 is the total of all

days to auto-disarm the system.

Disabled

Saturday

Friday

Thursday

Wednesday

Default

Range

0 - 127

Auto-Disarming Time (Hours)

Cmd Loc 027

16 Tuesday

32 Monday

64 Sunday

Default

Range

When programming the time of day for auto-dis-

arming, use the 24-hour format. (Add 12 hours for

afternoon and evening times.)

0 - 23

Auto-Disarming Time (Minutes)

Cmd Loc 028

Default

Range

0 - 59

Comments

Swinger Alarm Lockout Limit

Limits the number of alarm signals reported and/or annunciated during an

armed period. Additional alarms will not be indicated. Setting the limit to

zero (0) indicates unlimited signals reported. In partitioned systems, this

limit pertains to ALL partitions (areas).

Cmd Loc 029

Default

Range

0 - 15

Options:

Audible Output Limits

Comments

Unlimited Local Audibles.

Cmd Loc 030

Determines the number of times the

sounders (bells) will indicate an alarm

condition during an armed period.

One Audible per Zone.

One Audible per Area.

Default

Range

1 - 3

Fire Verification Enable

Comments

Options:

Cmd Loc 031

Determines if powered loop

(zone 8) or switched aux

power will be reset for fire

alarm verification.

No Verification

Default

Range

1 - 4

Powered Loop Verify Only

Switched Aux Verify Only

Powered Loop and Switched Aux

AC Power Loss Delay Before Report (Minutes)

Comments

Cmd Loc 032

Specifies the number of minutes AC power must be interrupted before an

AC power fail report is sent.

Default

Range

1 - 255

Battery Test Interval (Hours)

Comments

Cmd Loc 033

The interval (in hours) between battery tests. If programmed for 0, the test

is disabled. This test is conducted each time the system is reset. Additional

tests follow the test interval specified.

Default

Range

0 - 24

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 3 - Armed System Programming (cont.)

Sounder Turn-On Delay Following Alarm (Seconds)

Comments

Number of seconds that elapse following an alarm condition before the

internal siren/external bell sounds. The keypad buzzer is active during this

period.

Cmd Loc 034

Default

Range

0 - 255

Strobe/Siren Disable with Low Battery

Comments

Options:

If enabled, this option disables the strobe/siren, to extend

backup time with a low battery condition.

Cmd Loc 035

Yes

Default

Range

1 - 2

Comments

Phone Line Cut or Comm Fail Indication (Silent

to Audible)

Cmd Loc 036

Options:

If enabled, alarm conditions programmed as silent will con-

vert to audible.

Yes

Default

Range

1 - 2

Comments

Options:

Phone Line Cut Audible Action

Determines the audible action

to be taken when the tele-

phone line has been cut.

No Local Audible Annunciation.

Turn On Sounders.

Turn On Sounders only if armed.

Cmd Loc 037

Default

Range

1 - 3

Comments

Internal/External Sounder Output Duration

Amount of time the internal siren and external bell will sound following an

alarm condition. Sounder cadence is progammed in Block 2, CL 079 - 110.

(Minutes)

Cmd Loc 038

Default

Range

0 - 60

Comments

This option specifies the duration of the strobe

output (in days) following an alarm condition.

Options:

Strobe Output Duration (Days)

Strobe Disabled

Cmd Loc 039

1 - 6 Days

Default

Range

0 - 7

Strobe Latched

Comments

Soak Mode (Learning Period) Duration (Days)

Panel will operate as a local system only during this period. This will give

the user time to learn the system. All alarm indications during this period will

only be annunciated by keypad buzzer. The internal and external sound-

ers are also disabled during this period.

Cmd Loc 040

Default

Range

0 - 31

Duress Active Only When (Area) Armed

Comments

Options:

Cmd Loc 041

If enabled, the duress code will only disarm the system. The

duress code may not be used for arming.

Default

Range

1 - 2

Yes

If disabled, this option will send a duress report when arming or disarming.

Opening Report Programming Override

Comments

Options:

Cmd Loc 042

An Opening Report will be sent if the following conditions

are met:

Default

Range

1 - 2

Yes

1 - An alarm has occurred;

2 - the cancel report timer (Block 4, CL 110) has expired; and

3 - a valid user code is entered.

The report is sent, regardless of the User Code Privileges (Block 1,

CL 021 - 080) assigned to the user. The report will not override First

to Open/Last to Close (Block 9, CL 110) option.

Options:

Comments

External Bell Supervision Enable

If enabled, provides for supervision of external bell wiring

for opens, shorts, and ground faults. Bell supervision re-

quires an EOL resistor at the bell terminals. This option may

not be used if External Bell Reverse (Block 3, CL 048) is

active.

Cmd Loc 043

Yes

Default

Range

1 - 2

For proper supervision, Ground Fault Supervision (Block 3, CL 053) should

also be enabled.

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 3 - Armed System Programming (cont.)

Options:

Keypad Tamper Switch Enable (By Address)

Comments

Disabled

Each Cmd Loc will be programmed with

the total of the keypad addresses with ac-

tive tamper switches.

Keypad # 1 - 8

9 - 16

045

Keypad

Cmd Loc

Default

Range

044

0 - 255

Keypad Tampers are reported via the

keypad bus.

16 Keypad

32 Keypad

64 Keypad

128 Keypad

Reserved for Future Use

Comments

Cmd Loc 046 047

These locations are Reserved for Future Use and are not available in this

firmware version.

Default

Range

N/A N/A

External Bell Reverse Enable

Comments

Options:

Cmd Loc 048

If enabled, supplies voltage to external bell when bell is off.

This option may not be used with External Bell Supervision

(Block 3, CL 043) enabled.

Default

Range

1 - 2

Yes

Options:

Comments

Sounder (Bell) Test Enable (By Area)

Disabled

Area 1

Area 2

Area 3

Area 4

Sounds a 5-second bell test at the start of each exit

delay. The value programmed into this Cmd Loc is the

total of all areas for which the bell test will be active.

Cmd Loc 049

Default

Range

0 - 255

16 Area 5

32 Area 6

64 Area 7

128 Area 8

Home Arming Enable

Comments

Options:

Cmd Loc 050

This option, when enabled, allows a system to be home

armed or instant home-armed. All zones listed in the

Home Arm Bypass List (Block 2, CL 151 - 154) will be

automatically bypassed.

Default

Range

1 - 2

Yes

Keyswitch/SpreadNet Arming Annunciation

Options:

Comments

Cmd Loc 051

No Annunciation

Keypad Buzzer

Strobe

Internal Siren

External Bell

This option determines how keyswitch or

SpreadNet arming is annunciated. The value

programmed into this Cmd Loc is the total of

all sounders to be activated. When arming,

the selected sounders will beep three times

(1.5 sec on/off) and the strobe will light for 3

seconds. When disarming, the selected

sounders will beep once and the strobe will

be on for 1.5 seconds.

Default

Range

0 - 15

Auto-Arming Enable (Day of Week)

Comments

Options:

Cmd Loc 052

This will automatically arm the areas specified in

Block 3, CL 022 at the time specified in Block 3,

CL 023 and 024. The value programmed here is

the total for all days of the week when the system

will auto-arm.

Disabled

Default

Range

Saturday

Friday

Thursday

Wednesday

0 - 127

16 Tuesday

32 Monday

64 Sunday

Ground Fault Supervision Enable

Comments

Options:

Cmd Loc 053

This option, when enabled, reports and annunciates all

ground fault conditions.

Default

Range

1 - 2

Yes

When disabled, these conditions are not reported or

annunciated.

Download from Www.Somanuals.com. All Manuals Search And Download.

Home Arm Reports Enable

Comments

Options:

Cmd Loc 054

This option, when enabled, allows opening/closing and by-

pass reports to be sent to the central station, if programmed

in Block 1, CL 021 - 080 (User Code Privilege) and Block 5,

CL 069 - 072 (Zone Bypass Reports); CL 095 - 098 (Open-

ing Reports); and/or CL 099 - 102 (Closing Reports).

Default

Range

1 - 2

Yes

Block 4 - Digital Communicator Programming

This Block is divided into 164 Command Locations (CL 001 - 164). The programming locations in this Block reflect the

Receiver Type and Message Format for Receivers 1 & 2, Account Numbers, Phone Numbers (Receiver 1, 2, and RPS), Dialing

Parameters and Delays, and Call Routing (including SpreadNet).

Receiver Type (Receiver #1)

Options:

Radionics / Fast

Cmd Loc 001

ADEMCO 4+2 Express (DTMF)

10 Radionics / Slow

Default

Range

ADEMCO Contact ID (DTMF)

ADEMCO High Speed (DTMF)

SIA Level 1 (FSK)

SIA (Date and Time)

SIA (Area)

SIA (Date & Time + Area)

CFSK-IV (FSK)

11 Silent Knight / ADEMCO Fast

12 Silent Knight / ADEMCO Slow

13 Radionics High Speed

14 Numeric DTMF Pager (4+2)

15 Personal Dialing

1 - 15

NOTE: ADEMCO High Speed (option #3) may not be used

with systems having more than 8 zones.

Options:

Comments

Message Format (Receiver #1)

3/1 Dual Round

Specifies the method of sending the

reported message (Account Num-

ber and Reporting Code) to the

Central Station.

Cmd Loc 002

4/1 Dual Round

4/2 Dual Round

3/1 Extended Dual Round

Default

Range

1 - 4

NOTE: The 4/1 Message Format may not be

used with Radionics High Speed.

Options:

Receiver Type (Receiver #2)

CFSK-IV (FSK)

Radionics / Fast

ADEMCO 4+2 Express (DTMF)

ADEMCO Contact ID (DTMF)

ADEMCO High Speed (DTMF)

SIA Level 1 (FSK)

SIA (Date and Time)

SIA (Area)

Cmd Loc 003

Default

Range

10 Radionics / Slow

1 - 15

11 Silent Knight / ADEMCO Fast

12 Silent Knight / ADEMCO Slow

13 Radionics High Speed

14 Numeric DTMF Pager (4+2)

15 Personal Dialing

SIA (Date & Time + Area)

NOTE: ADEMCO High Speed (option #3) may not be used with

systems having more than 8 zones.

Message Format (Receiver #2)

Comments

Options:

Cmd Loc 004

Specifies the method of sending the re-

ported message (account number and

reporting code) to the central station.

3/1 Dual Round

Default

Range

1 - 4

4/1 Dual Round

4/2 Dual Round

3/1 Extended Dual Round

NOTE: The 4/1 Message Format may not be

used with Radionics High Speed.

Account #1

Comments

Cmd Loc 005

006

007

008

009

010

This is a 6-digit account number which is used by Receiver 1.

Default

Range

In a partitioned system, this is the account number for area #1.

0 - 15 0 - 15 0 - 15 0 - 15 0 - 15 0 - 15

Account #2

Comments

Cmd Loc 011

012

013

014

015

016

This is a 6-digit account number which is used by Receiver 2.

Default

Range

In a partitioned system, this is the account number for area #2.

0 - 15 0 - 15 0 - 15 0 - 15 0 - 15 0 - 15

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 4 - Digital Communicator Programming (cont.)

Account #3

Comments

Cmd Loc 017

018

019

020

021

022

In a partitioned system, this is the account number for area #3.

Default

Range

0 - 15 0 - 15 0 - 15 0 - 15 0 - 15 0 - 15

Account #4

Comments

Cmd Loc 023

024

025

026

027

028

In a partitioned system, this is the account number for area #4.

Default

Range

0 - 15 0 - 15 0 - 15 0 - 15 0 - 15 0 - 15

Account #5

Comments

Cmd Loc 029

030

031

032

033

034

In a partitioned system, this is the account number for area #5.

Default

Range

0 - 15 0 - 15 0 - 15 0 - 15 0 - 15 0 - 15

Account #6

Comments

Cmd Loc 035

036

037

038

039

040

In a partitioned system, this is the account number for area #6.

Default

Range

0 - 15 0 - 15 0 - 15 0 - 15 0 - 15 0 - 15

Account #7

Comments

Cmd Loc 041

042

043

044

045

046

In a partitioned system, this is the account number for area #7.

Default

Range

0 - 15 0 - 15 0 - 15 0 - 15 0 - 15 0 - 15

Account #8

Comments

Cmd Loc 047

048

049

050

051

052

In a partitioned system, this is the account number for area #8.

Default

Range

0 - 15 0 - 15 0 - 15 0 - 15 0 - 15 0 - 15

Options:

Telephone Number (Receiver #1)

Cmd Loc 053 054 055 056 057 058 059 060

Cmd Loc 061 062 063 064 065 066 067 068

Comments

0 - 9 Dialing Digits

Each telephone number may be

up to 16 digits long. Acceptable

values are the digits 0 - 9 and the

special characters shown at the

right.

10 Dial Tone Detect

11 Not Used

12 * [Star Key] - Not Available

with Pulse Dialing

13 # [Pound Key] -Not Avail-

able with Pulse Dialing

14 End of Number - All Cmd

Locs following this charac-

ter are ignored

Default

Range

14 (All Locations)

0 - 15 (All Locations)

Telephone Number (Receiver #2)

Cmd Loc 069 070 071 072 073 074 075 076

Cmd Loc 077 078 079 080 081 082 083 084

Default

Range

14 (All Locations)

0 - 15 (All Locations)

15 5 second Dialing Pause

Telephone Number (RPS Callback)

Cmd Loc 085 086 087 088 089 090 091 092

Cmd Loc 093 094 095 096 097 098 099 100

Default

Range

14 (All Locations)

0 - 15 (All Locations)

Options:

Dial Type

Comments

DTMF (5 tones/sec)

Pulse

DTMF/Pulse Alternating (DTMF first)

Cmd Loc 101

Determines the format

used for all dialing opera-

tions.

Default

Range

1 - 3

Dial Attempt Limit

Comments

Cmd Loc 102

Determines the number of times the digital communicator will attempt to

place a call (per phone number) before reporting a comm fail. To set up

the system as a local panel (non-reporting), enter 0 into this location.

Default

Range

0 - 15

Telephone Ring Cadence

Comments

Options:

Cmd Loc 103

This is the ring cadence used by the local telephone

system. In a double-ring system, two rings count as

a one.

Single Ring

Double Ring

Default

Range

1 - 2

Options:

Ring Count to Answer

Comments

Auto-Answer Disabled

Cmd Loc 104

This option determines the

procedure the system will

use when answering incom-

ing phone calls.

2 - 14 Number of Rings Before Answering

15 Answering Machine Bypass

Default

Range

1 - 15

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 4 - Digital Communicator Programming (cont.)

Comments

RPS Callback Enable

Options:

If enabled, requires the panel to call COMMANDER II in

order to establish RPS. If disabled, the panel will stay on-line

when called by COMMANDER II the second time (following

handshaking).

Cmd Loc 105

Default

Range

1 - 2

Yes

Keypad RPS Enable

Comments

Options:

Cmd Loc 106

If enabled, allows remote programming to be initiated from

the keypad (either Block 0 or user programming).

Default

Range

1 - 2

Yes

RPS and CFSK-IV Modem Type

Comments

Options:

Cmd Loc 107

Establishes the modem protocol for RPS and CFSK-IV

communications.

Bell 103

CCITT

Default

Range

1 - 2

Alarm Dialing Delay (Seconds)

Cmd Loc 108

Comments

The delay (in seconds) after an alarm occurs before the report is sent.

Default

Range

0 - 255

24-Hour Zone Dial Delay

Comments

Options:

Cmd Loc 109

If enabled, uses the time programmed above (Block 4, CL

108) for reporting alarms on 24-hour zones. If disabled, 24-

hour zones report immediately.

Default

Range

1 - 2

Yes

Cancel Report Delay (Seconds)

Comments

Cmd Loc 110

The amount of time (in seconds), following an alarm, during which a cancel

report may be sent. The cancel report is not sent if a valid user code is

entered before the alarm dialing delay has expired.

Default

Range

0 - 255

Dialer Retry Sequence

Options:

Cmd Loc 111

Repeat Call Attempt Series at 30 min.

then double interval up to 128 hrs.

No additional Call Attempts After Failed

Series Until New Report is Queued.

Repeat Call Attempt

Series Every 30 min.

Repeat Call Attempt

Series Every four hrs.

Default

1 - 4

Range

Phone Line Call Routing

Options:

Cmd Loc 112

Line #1 with Line #2 as Backup,

Alternating (2 Attempts Each)

Line #1 with Line #2 as Backup,

Alternating (4 Attempts Each)

Line #1 Only

Default

Range

1 - 4

Line #1 with Line #2 Backup

(Phone Line Cut or Comm

Fail)

Test Report Interval (Days)

Comments

Cmd Loc 113

This option determines the test interval. Test reports are sent in daily

intervals, ranging from 1 to 30 days. The time of day for the report is

programmed into Block 4, CL 114. To disable reporting, set to 0.

Default

Range

0 - 30

Test Report Time of Day (Hours)

Comments

Cmd Loc 114

When programming the test report time of day, use the 24-hour format.

(Add 12 hours for afternoon and evening times.)

Default

Range

0 - 23

Ringback Outputs Enable

Comments

The selected outputs will sound for three sec-

onds following a successful closing report.

Options:

Cmd Loc 115

Disable

Default

Range

Keypad Buzzer

Strobe

Internal Siren

External Bell

0 - 15

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 4 - Digital Communicator Programming (cont.)

Report Routing (Zones 1 - 32)

Comments

Options:

Cmd Loc 116 117 118 119 120 121 122 123

These locations determine the report routing

for alarms, bypasses, troubles, tampers,

restorals, and cancel reports on all zones.

Disable Reports

Zone #

Cmd Loc 124 125 126 127 128 129 130 131

Zone # 10 11 12 13 14 15 16

Cmd Loc 132 133 134 135 136 137 138 139

Zone # 17 18 19 20 21 22 23 24

Cmd Loc 140 141 142 143 144 145 146 147

Receiver 1 Only

Receiver 2 Only

Receivers 1 and 2

Receiver 1, with

Receiver 2 as Back-

up, Alternating

Zone #

Default

Range

2 (All CL)

1 - 5 (All CL)

28 29 30 31

Comments

Keypad Medical, Police, and Fire Report Routing

Report routing for soft zone alarms, if soft

zones are enabled (Block 2, CL 155 - 157).

Cmd Loc

Default

Range

148

1 - 5

Duress Report Routing

Comments

Report routing for all duress codes. Areas

are indicated by the account number.

Cmd Loc 149

Default

Range

1 - 5

Comments

Report routing for opening and closing re-

ports, if enabled.

Opening / Closing Report Routing

Cmd Loc 150

Default

Range

1 - 5

Comments

Report routing for test reports.

Test Report Routing

Cmd Loc 151

Default

Range

1 - 5

Comments

Report routing for AC power fail, low battery,

and the respective restoral reports.

Power Supply Report Routing

Cmd Loc 152

Default

Range

1 - 5

Phone Line Trouble Report Routing

Comments

Report routing for phone line cut or comm fail

reports.

Cmd Loc 153

Default

Range

1 - 5

Kidwatch Check-In Fail Report Routing

Comments

Cmd Loc 154

If Kidwatch is enabled and the Kidwatch code

is not entered during the Kidwatch window

(Block 6, CL 006 - 009), a report will be sent.

Default

Range

1 - 5

Installer Programming Report Routing

Comments

Report routing for installer programming start

and end reports (see Block 5, CL 135 - 138).

Cmd Loc 155

Default

Range

1 - 5

Bell Supervision Trouble Report Routing

Comments

Report routing for external bell supervision

trouble and restoral reports.

Cmd Loc 156

Default

Range

1 - 5

SpreadNet Transmitter Low Battery Report Routing

Comments

Report routing for all SpreadNet transmitters

low battery and restoral reports.

Cmd Loc

Default

Range

157

1 - 5

Keypad and Accessory Tamper Report Routing

Comments

Cmd Loc 158

Report routing for all tamper and restoral re-

ports associated with keypads and accesso-

ries connected to the system.

Default

Range

1 - 5

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 4 - Digital Communicator Programming (cont.)

Keypad and Accessory Communications

Trouble Report Routing

Comments

Options:

Report routing for all communication trouble

and restoral reports associated with keypads

and accessories connected to the system.

Disable Reports

Receiver 1 Only

Receiver 2 Only

Receivers 1 and 2

Receiver 1, with

Receiver 2 as Back-

up, Alternating

Cmd Loc 159

Default

Range

1 - 5

Audio Verification Enable (Listen-In)

Options:

Cmd Loc 160

No Audio Verification (AV)

Default

Range

1 - 4

Trigger AV following alarm, but before releasing line. Panel may not

seize line for 3 min. or send reports until AV session is complete.

Same as option #1, but allows reports to interrupt AV session.

Same as option #1, except retriggers AV when panel attempts to

seize line to send alarm report.

Comments

Digital Communications Enable

Options:

If disabled, programmed for No (1), the sys-

tem will operate as a local system. Phone line

checking will also be disabled. For reporting

systems, program this location as Yes (2).

Cmd Loc 161

No (Local System)

Yes

Default

Range

1 - 2

Telephone Line #1 Supervision Time (Minutes)

Cmd Loc 162

Comments

Amount of time (in minutes) that the phone line must be cut (open) before

annunciation will occur and a report is sent to the central station. This is also

the time interval required before the phone line cut action (Block 3, CL 036

and 037). Programming either command location with 0 will disable phone

line checking for that line.

Default

Range

0 - 30

Telephone Line #2 Supervision Time (Minutes)

Cmd Loc 163

Default

Range

If the system is equipped with a single-line digital communicator, the pro-

gramming of CL 163 will be ignored.

0 - 30

Test Report Phone Line Routing

Comments

Options:

Cmd Loc 164

This option allows the installer to select the phone line

which will be used to send test reports. If a dual-line

digital communicator is used, both lines may be se-

lected for test reporting. The data programmed in

this location overrides the programming of Block 4,

CL 112 for test reports only.

Line #1 Only

Default

Range

1 - 3

Line #2 Only

Line #1 and

Line #2

Block 5 - Reporting Digits Programming

This Block has 180 Command Locations (CL 001 - 180). Certain reporting formats such as CFSK-IV, Contact ID, and SIA

have pre-defined codes and the data programmed here is ignored. Reports may be disabled by programming the

reporting code as 0 (or 00 for two-digit codes). Each Cmd Loc may be programmed with any value from 0 - 15.

Report Code, Alarm (Zones 1 - 32)

Cmd Loc 001 002 003 004 005 006 007 008 009 010 011 012

Comments

Default

Zone

These codes are used to indicate alarm conditions. Each report code is a

two-digit code. Reports may be disabled by programming a value of 00

into the Cmd Loc. Each location may contain any digit from 0 - 15.

Cmd Loc 013 014 015 016 017 018 019 020 021 022 023 024

Default

Zone

NOTE: The programmed digits 10 - 15 will be sent to the central station as

their hexadecimal equivalent, as shown in the table below:

Cmd Loc 025 026 027 028 029 030 031 032 033 034 035 036

Default

Zone

Cmd Loc 037 038 039 040 041 042 043 044 045 046 047 048

Reporting Digit Conversion:

Default

Zone

Decimal

Hexadecimal

Cmd Loc 049 050 051 052 053 054 055 056 057 058 059 060

Default

Zone

Cmd Loc 061 062 063 064

Default

Zone

Range

0 - 15 (All CL)

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 5 - Reporting Digits Programming (cont.)

Comments

Report Code, Restoral (Zones 1 - 32)

The restoral report code is a single-digit code. For 2-digit reporting for-

mats, the relative zone number (1 - 8) is sent as the second digit. Disable

the reporting by programming 0 into the specific Cmd Loc. Disabling a

Cmd Loc disables reporting for all zones associated with that location.

Zones:

Cmd Loc

Default

Range

1 - 8

065

9 - 16

17 - 24 25 - 32

066

067

068

0 - 15

Comments

Report Code, Zone Bypass (Zones 1 - 32)

The zone bypass report code is a single-digit code. For two-digit reporting

formats, the relative zone number (1 - 8) is sent as the second digit. Disable

this report by programming 0 into the specific Cmd Loc. Disabling a Cmd

Loc disables reporting for all zones associated with that location.

Zones:

Cmd Loc

Default

Range

1 - 8

069

9 - 16

17 - 24 25 - 32

070

071

072

0 - 15

Report Code, Trouble (Zones 1 - 32)

Comments

The zone trouble report code is a single-digit code. For two-digit reporting

formats, the relative zone number (1 - 8) is sent as the second digit. Disable

the reporting by programming 0 into the specific Cmd Loc. Disabling a

Cmd Loc disables reporting for all zones associated with that location.

Zones:

Cmd Loc

Default

Range

1 - 8

073

9 - 16

17 - 24 25 - 32

075

074

076

0 - 15

Report Code, Tamper (Zones 1 - 32)

Comments

The zone tamper report code is also a single-digit code. For two-digit

reporting formats, the relative zone number (1 - 8) is sent as the second

digit. Program the specific Cmd Loc with 0 to disable reporting. Disabling

a Cmd Loc disables reporting for all zones associated with that location.

Zones:

Cmd Loc

Default

Range

1 - 8

077

9 - 16

17 - 24 25 - 32

079

078

080

0 - 15

Report Code, Soft Zone (Medical)

Comments

This is the code sent to the central station when the Medical soft zone is

activated from the keypad. Disable reporting by programming 00 into

these Cmd Loc.

Key:

Medical

081 - 082

Cmd Loc

Default

Range

0 - 15

Comments

Report Code, Soft Zone (Medical) Restoral

This is the code sent to the central station when the user enters a valid user

code following a keypad-activated Medical emergency. Disable reporting

by programming 00 into these Cmd Loc.

Key:

Medical

Cmd Loc

Default

Range

083 - 084

0 - 15

Report Code, Soft Zone (Police)

Comments

This is the code sent to the central station when the Police soft zone is

activated from the keypad. Disable reporting by programming 00 into

these Cmd Loc.

Key:

Police

085 - 086

Cmd Loc

Default

Range

0 - 15

Report Code, Soft Zone (Police) Restoral

Comments

This is the code sent to the central station when the user enters a valid user

code following a keypad-activated Police emergency. Disable reporting

by programming 00 into these Cmd Loc.

Key:

Police

087 - 088

Cmd Loc

Default

Range

0 - 15

Report Code, Soft Zone (Fire)

Comments

This is the code sent to the central station when the Fire soft zone is acti-

vated from the keypad. Disable the reporting by programming 00 into

these Cmd Loc.

Key:

Fire

089 - 090

Cmd Loc

Default

Range

0 - 15

Report Code, Soft Zone (Fire) Restoral

Comments

This is the code sent to the central station when the user enters a valid user

code following a keypad-activated Fire emergency. Disable reporting by

programming 00 into these Cmd Loc.

Key:

Fire

Cmd Loc

Default

Range

091 - 092

0 - 15

Report Code, Duress

Comments

Cmd Loc 093 - 094

This is the code sent to the central station when the user enters a duress

code. (See Block 3, CL 041 to determine when the duress code is active.)

If the system is divided into areas, the area associated with the duress code

will be identified by the account number (see Block 4, CL 005 - 052).

Disable the reporting by programming 00 into the specified Cmd Loc.

Default

Range

0 - 15

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 5 - Reporting Digits Programming (cont.)

Comments

Report Code, Opening (Users 1 - 60)

User #: 1 - 15 16 - 30 31 - 45 46 - 60

The opening report code is a single-digit code. For two-digit reporting

formats, the relative user number (1 - 15) is sent as the second digit.

Program the specific Cmd Loc with 0 to disable reporting. Disabling a

Cmd Loc disables reporting for all users associated with that location.

Cmd Loc

Default

Range

095

0 - 15

096

0 - 15

097

0 - 15

098

0 - 15

Comments

Report Code, Closing (Users 1 - 60)

User #: 1 - 15 16 - 30 31 - 45 46 - 60

The closing report code is a single-digit code. For two-digit reporting

formats, the relative user number (1 - 15) is sent as the second digit.

Program the specific Cmd Loc with 0 to disable reporting. Disabling a

Cmd Loc disables reporting for all users associated with that location.

Cmd Loc

Default

Range

099

0 - 15

100

0 - 15

101

0 - 15

102

0 - 15

Report Code, Cancel (Users 1 - 60)

User #: 1 - 15 16 - 30 31 - 45 46 - 60

Comments

The cancel report code is a single-digit code. For two-digit reporting for-

mats, the relative user number (1 - 15) is sent as the second digit. Program

the specific Cmd Loc with 0 to disable reporting. Disabling a Cmd Loc

disables reporting for all users associated with that location.

Cmd Loc

Default

Range

103

0 - 15

104

0 - 15

105

0 - 15

106

0 - 15

Comments

Report Code, Exit Fail Alarm (Zones 1 - 32)

The exit fail report code is a single-digit code which is sent if the exit (delay)

zone remains faulted at the end of the exit delay. The alarm is generated in

association with the Chirp-Alert Warning (Block 3, CL 009). For two-digit

reporting formats, the relative zone number (1 - 8) is sent as the second

digit. Program the specific Cmd Loc with 0 to disable reporting. Disabling

a Cmd Loc disables reporting for all zones associated with that location.

Zones:

Cmd Loc

Default

Range

1 - 8

107

9 - 16

17 - 24 25 - 32

108

109

110

0 - 15

Report Code, Kidwatch Check-in Failure

Comments

Cmd Loc 111 112

This two-digit code is sent to the central station if the Kidwatch code (user

#11) is not entered during the Kidwatch period (Block 6, CL 006 - 009).

Disable the reporting by programming 00 into these Cmd Loc.

Default

Range

0 - 15 (All CL)

Comments

Report Code, AC Power Loss

These two-digit codes are used to report AC power failures and restorals.

Only the second digit is sent when using single-digit reporting formats.

Cmd Loc 113 114

Default

Range

0 - 15 (All CL)

Report Code, AC Power Restoral

Cmd Loc 115 116

Default

Range

0 - 15 (All CL)

Comments

Report Code, Low Battery

These two-digit report codes will be sent to indicate a low battery condition

or restoral report. When using single-digit reporting formats, only the sec-

ond digit will be sent.

Cmd Loc 117 118

Default

Range

0 - 15 (All CL)

Report Code, Low Battery Restoral

Cmd Loc 119 120

Default

Range

0 - 15 (All CL)

Report Code, Test

Comments

Cmd Loc 121 122

This two-digit report code will be sent to indicate a system test. When using

single-digit reporting formats, only the second digit is sent.

Default

Range

0 - 15 (All CL)

Comments

Report Code, Failure to Report (Comm Fail)

These two-digit report codes will be sent to indicate a comm fail (failure to

report) condition. The reports are also sent to indicate a comm fail restoral.

Only the second digit is sent when using single-digit reporting formats.

Cmd Loc 123 124

Default

Range

0 - 15 (All CL)

Report Code, Fail to Report (Comm Fail) Restoral

Cmd Loc

Default

Range

125 126

0 - 15 (All CL)

Report Code, Primary Phone Line Cut

Comments

Cmd Loc 127 128

These two-digit codes are sent when the system detects a primary or

secondary phone line cut, or their respective restorals. When using single-

digit reporting formats, only the second digit is sent.

Default

Range

0 - 15 (All Locations)

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 5 - Reporting Digits Programming (cont.)

Comments

Report Code, Primary Phone Line Restoral

These two-digit codes are sent when the system detects a primary or

secondary phone line cut, or their respective restorals. When using single-

digit reporting formats, only the second digit is sent.

Cmd Loc 129 130

Default

Range

0 - 15 (All Locations)

Report Code, Secondary Phone Line Cut

Cmd Loc 131 132

Default

Range

0 - 15 (All Locations)

Report Code, Secondary Phone Line Restoral

Cmd Loc 133 134

Default

Range

0 - 15 (All Locations)

Comments

Report Code, Installer Programming Start

This two-digit report code will be sent to indicate the start of installer pro-

gramming. Single-digit reporting formats will only send the second digit to

the central station.

Cmd Loc 135 136

Default

Range

0 - 15 (All Locations)

Report Code, Installer Programming Complete

Cmd Loc 137 138

Default

Range

0 - 15 (All Locations)

Report Code, Bell Supervision Trouble

Comments

Cmd Loc 139 140

These two-digit report codes will be sent to indicate an external bell super-

vision trouble condition or a restoral report. When using single-digit report-

ing formats, only the second digit will be sent.

Default

Range

0 - 15 (All Locations)

Report Code, Bell Supervision Trouble Restoral

Cmd Loc 141 142

Default

Range

0 - 15 (All Locations)

Report Code, SpreadNet Supervisory Trouble

Comments

The SpreadNet supervisory trouble and supervisory trouble restoral re-

port codes are single-digit codes. For two-digit reporting formats, the

relative zone number (1 - 8) is sent as the second digit. Program the

specific Cmd Loc with 0 to disable reporting. Disabling a Cmd Loc dis-

ables reporting for all zones associated with that location.

Zones:

Cmd Loc

Default

Range

1 - 8

143

9 - 16

17 - 24 25 - 32

144

145

146

0 - 15

Report Code, SN Supervisory Trouble Restoral

Zones:

Cmd Loc

Default

Range

1 - 8

147

9 - 16

17 - 24 25 - 32

148

149

150

0 - 15

Report Code, SN Transmitter Low Battery

Comments

Zones:

Cmd Loc

Default

Range

1 - 8

151

9 - 16

17 - 24 25 - 32

The SpreadNet low battery and low battery restoral report codes are a

single-digit code. For two-digit reporting formats, the relative zone number

(1 - 8) is sent as the second digit. Program the specific Cmd Loc with 0 to

disable reporting. Disabling a Cmd Loc disables reporting for all zones

associated with that location.

152

153

154

0 - 15

Report Code, SN Tx Low Battery Restoral

Zones:

Cmd Loc

Default

Range

1 - 8

155

9 - 16

17 - 24 25 - 32

156

157

158

0 - 15

Report Code, Ground Fault

Cmd Loc 159 160

Comments

These two-digit report codes will be sent to indicate a ground fault condi-

tion or restoral report. When using single-digit reporting formats, only the

second digit will be sent.

Default

Range

0 - 15 (All CL)

Report Code, Ground Fault Restoral

Cmd Loc 161 162

Default

Range

0 - 15 (All CL)

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 5 - Reporting Digits Programming (cont.)

Comments

Report Code, Report Queue Overflow

This two-digit report code will indicate that the report buffer has over-

flowed. When using single-digit reporting formats, only the second digit is

sent.

Cmd Loc 163 164

Default

Range

0 - 15 (All CL)

Report Code, SN Keypad Supervisory Failure

Comments

Cmd Loc 165

The SpreadNet keypad supervisory (check-in) failure and restoral report

codes are a single-digit code. For two-digit reporting formats, the keypad

address is sent as the second digit. To disable reporting, program 0 into

the specific location.

Default

Range

0 - 15

Report Code, SN Kpd Supervisory Fail Restoral

Cmd Loc 166

Default

Range

0 - 15

Report Code, SpreadNet Keypad/Keyfob Low

Battery

Cmd Loc 167

Comments

These report codes apply to the SpreadNet keypad, remote, and keyfob.

The low battery and restoral report codes are a single-digit code. For two-

digit reporting formats, the respective keypad number or user number

associated with the remote/keyfob will be sent as the second digit. To

disable reporting, program 0 into the specific location.

Default

Range

0 - 15

Report Code, SpreadNet Keypad/Keyfob Low

Battery Restoral

Cmd Loc 168

Default

Range

0 - 15

Report Code, Accessory Tamper

Comments

Accessory Addresses

1 - ZEM #1

2 - ZEM #2

3 - ZEM #3

4 - Not Used (Reserved)

5 - REMM #1

Cmd Loc 169

The respective report code is sent to indi-

cate a tamper or trouble condition (or the

respective restoral report) associated with

a specific accessory. For two-digit report-

ing formats, a hardcoded address is

added as the second digit. The addresses

for each accessory are listed to the right.

Default

Range

0 - 15

Report Code, Accessory Tamper Restoral

Cmd Loc 170

Default

Range

6 - REMM #2

7 - SN915-BUS Receiver

0 - 15

Report Code, Accessory Trouble

Cmd Loc 171

Default

Range

0 - 15

Report Code, Accessory Trouble Restoral

Cmd Loc 172

Default

Range

0 - 15

Report Code, Keypad Tamper

Comments

Cmd Loc 173 174

These two-digit report codes indicate tamper, trouble, and restoral con-

ditions associated with hardwired keypads. When using single-digit

reporting formats, only the second digit is sent.

Default

Range

0 - 15 (All CL)

Report Code, Keypad Tamper Restoral

Cmd Loc 175 176

Default

Range

0 - 15 (All CL)

Report Code, Keypad Trouble

Cmd Loc 177 178

Default

Range

0 - 15 (All CL)

Report Code, Keypad Trouble Restoral

Cmd Loc 179 180

Default

Range

0 - 15 (All CL)

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 6 - Real Time Clock Programming

The Real Time Clock Programming Block is divided into two sections and has a total of 9 Command Locations (CL 001

- 009). The two sections relate to the system clock and the Kidwatch timer.

Date (Day of Month)

Comments

Cmd Loc 001

The system clock is used for date and time stamping of events stored in

Default

Range

Event Memory. This information is also associated with certain reporting

formats (see Block 4, CL 001 and 003 for additional information).

1 - 31

Date (Month)

Cmd Loc 002

Default

Range

1 - 12

Date (Current Year)

Cmd Loc 003

Default

Range

00 - 99

Time of Day (Hours)

Cmd Loc 004

Default

Range

0 - 23

Time of Day (Minutes)

Cmd Loc 005

Default

Range

0 - 59

Comments

Kidwatch Start Time (Hours)

If the Kidwatch feature is enabled (see Block 1, CL 019), the Kidwatch

timer (window) is programmed into these Cmd Locs.

Cmd Loc 006

Default

Range

0 - 23

Failure to enter the Kidwatch code during this period will result in the

system sending a Kidwatch Check-In Fail Report (see Block 4, CL 154 and

Block 5, CL 111 - 112 for additional details).

Kidwatch Start Time (Minutes)

Cmd Loc 007

Default

Range

0 - 59

Kidwatch End Time (Hours)

Cmd Loc 008

Default

Range

0 - 23

Kidwatch End Time (Minutes)

Cmd Loc 009

Default

Range

0 - 59

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 7 - Auxiliary Devices Programming

The Auxiliary Devices Programming Block has a total of 79 Command Locations (CL 001 - 079). Each of the first 11

commands has an input range of 1 - 82. Additional relay Options are provided for setting up specific timing operations.

Options:

1 Disabled, relay open

2 Close on SN “Door” button (keypad or re-

mote) activation

3 Closed when entire system armed

4 Closed when entire system disarmed

5 0.5 sec on/off (3x) when keyswitch or Spread-

Net arming; 1.5 sec on for keyswitch or

SpreadNet disarming (ignores timer)

6 Close on any tamper

42 Close when armed, oscillate at 0.5 Hz when

home armed (area 8)

On Board Relay

Cmd Loc 001

43 Close on relay user code 14 entry

44 Close on relay user code 18 entry

45 Close on relay user code 22 entry

46 Close on relay user code 26 entry

47 Close on relay user code 30 entry

48 Close on relay user code 34 entry

49 Close on relay user code 38 entry

50 Close on relay user code 42 entry

51 Close on user code entry (area 1)

52 Close on user code entry (area 2)

53 Close on user code entry (area 3)

54 Close on user code entry (area 4)

55 Close on user code entry (area 5)

56 Close on user code entry (area 6)

57 Close on user code entry (area 7)

58 Close on user code entry (area 8)

59 Close on duress (area 1), open on next area 1

user code entry (except Duress code)

60 Close on duress (area 2), open on next area 2

user code entry (except Duress code)

61 Close on duress (area 3), open on next area 3

user code entry (except Duress code)

62 Close on duress (area 4), open on next area 4

user code entry (except Duress code)

63 Close on duress (area 5), open on next area 5

user code entry (except Duress code)

64 Close on duress (area 6), open on next area 6

user code entry (except Duress code)

65 Close on duress (area 7), open on next area 7

user code entry (except Duress code)

66 Close on duress (area 8), open on next area 8

user code entry (except Duress code)

67 Relay status #1 (see below) (ignores timer)

68 Relay status #2 (see below) (ignores timer)

69 Close on bell supervision trouble

70 Close on keypad/accessory trouble or tamper

71 Close on Medical alarm

Default

Range

1 - 82

Relay #1 - REMM #1

Cmd Loc 002

Default

Range

1 - 82

Relay #2 - REMM #1

Cmd Loc 003

7 Close when phone line cut

8 Close when comm fail occurs

9 3-sec toggle to activate listen-in (ignores timer)

10 Follow keypad audible sounder (exit/entry de-

lays, area 1 only) (ignores timer)

11 Close on fault (except 24-hr. zone); open when

faulted zone is bypassed, restored, system

armed, or timer

12 Close on any alarm

13 Close on fire alarm

14 Close on burglar alarm

15 Close on panic/holdup

16 Close in installer programming mode

17 Activated by Commander II (RPS)

18 Close at end of exit delay (all areas armed),

open at start of entry delay

19 Close on area 1 alarm

20 Close on area 2 alarm

21 Close on area 3 alarm

22 Close on area 4 alarm

23 Close on area 5 alarm

24 Close on area 6 alarm

25 Close on area 7 alarm

26 Close on area 8 alarm

27 Close when area 1 armed

28 Close when area 2 armed

29 Close when area 3 armed

30 Close when area 4 armed

31 Close when area 5 armed

32 Close when area 6 armed

33 Close when area 7 armed

34 Close when area 8 armed

35 Close when armed, oscillate at 0.5 Hz when

home armed (area 1)

36 Close when armed, oscillate at 0.5 Hz when

home armed (area 2)

37 Close when armed, oscillate at 0.5 Hz when

home armed (area 3)

38 Close when armed, oscillate at 0.5 Hz when

home armed (area 4)

39 Close when armed, oscillate at 0.5 Hz when

home armed (area 5)

Default

Range

1 - 82

Relay #3 - REMM #1

Cmd Loc 004

Default

Range

1 - 82

Relay #4 - REMM #1

Cmd Loc 005

Default

Range

1 - 82

Relay #5 - REMM #1

Cmd Loc 006

Default

Range

1 - 82

Relay #1 - REMM #2

Cmd Loc 007

Default

Range

1 - 82

Relay #2 - REMM #2

Cmd Loc 008

Default

Range

1 - 82

Relay #3 - REMM #2

Cmd Loc 009

72 3-sec toggle for annunciator shutoff (ignores

timer)

73 3-sec toggle on local bell test (ignores timer)

74 Close on alarm associated with zone activated

relay (see Block 7, CL 035 - 066)

75 Close on AC fail

76 Close on low battery

77 Close on chime zone fault

78 Close on system trouble

79 Close on Pre-set Timer #1 (Block 7, CL 067 -

069)

80 Close on Pre-set Timer #2 (Block 7, CL 070 -

072)

Default

Range

1 - 82

Relay #4 - REMM #2

Cmd Loc 010

Default

Range

1 - 82

Relay #5 - REMM #2

Cmd Loc 011

Default

Range

1 - 82

40 Close when armed, oscillate at 0.5 Hz when

home armed (area 6)

81 Close on Pre-set Timer #3 (Block 7, CL 073 -

075)

41 Close when armed, oscillate at 0.5 Hz when

home armed (area 7)

82 Close on Pre-set Timer #4 (Block 7, CL 076 -

078)

Relay status #1

Relay status #2

NOTE: All relays may be programmed to open ac-

cording to a timer (Block 7, CL 013 - 034), unless

otherwise indicated. For additional information,

refer to the S5090 Reference Manual.

System Status Alarms? Relay State

Disarmed

Armed

Yes

Closed

Open

Closed

Open

Disarmed

Armed

Yes

Open

Closed

Open

Armed

NOTE: Relays are open when de-energized.

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 7 - Auxiliary Devices Programming (cont.)

Exit Delay Terminator

Comments

Options:

Cmd Loc 012

If enabled, jumps to the last 5 seconds of the exit delay,

then arms the system. Requires a normally open switch

connected to keypad (TXD and C terminals).

Default

Range

1 - 2

Yes

Options:

Timer Units (On Board Relay)

Comments

Latched

Seconds

Minutes

Hours

Cmd Loc 013

Each relay has its own independent countdown timer.

The timer consists of two parts: the Units and the Counter.

The countdown timer determines the amount of time a

relay will remain closed. For the On-Board Relay, CL 013

stores the units, while CL 014 stores the starting count.

The timer will count backwards and when it reaches 0,

the respective relay will open.

Default

Range

1 - 5

Timer Count (On Board Relay)

Cmd Loc 014

Days

Default

Range

1 - 255

NOTE: The timer function is ignored if the Relay option (Block 7, CL 001 -

011) is programmed for SpreadNet Arming/Disarming (option #5), Listen-In

Trigger (option #9), Follows Keypad Sounder (option #10), Relay Status #1

(option #67), Relay Status #2 (option #68), 3-second Toggle for Audible

Shutoff (option #72), or 3-second Toggle for Local Bell Test (option #73).

Comments

Timer Units (REMM #1, Relay #1)

For REMM #1, Relay #1, CL 015 stores the units, while

CL 016 stores the starting count. The timer will count

backwards and when it reaches 0, the respective relay

will open.

Cmd Loc 015

Default

Range

1 - 5

Timer Count (REMM #1, Relay #1)

Cmd Loc 016

Default

Range

1 - 255

Comments

Timer Units (REMM #1, Relay #2)

For REMM #1, Relay #2, CL 017 stores the units, while

CL 018 stores the starting count. The timer will count

backwards and when it reaches 0, the respective relay

will open.

Cmd Loc 017

Default

Range

1 - 5

Timer Count (REMM #1, Relay #2)

Cmd Loc 018

Default

Range

1 - 255

Comments

Timer Units (REMM #1, Relay #3)

For REMM #1, Relay #3, CL 019 stores the units, while

CL 020 stores the starting count. The timer will count

backwards and when it reaches 0, the respective relay

will open.

Cmd Loc 019

Default

Range

1 - 5

Timer Count (REMM #1, Relay #3)

Cmd Loc 020

Default

Range

1 - 255

Comments

Timer Units (REMM #1, Relay #4)

For REMM #1, Relay #4, CL 021 stores the units, while

CL 022 stores the starting count. The timer will count

backwards and when it reaches 0, the respective relay

will open.

Cmd Loc 021

Default

Range

1 - 5

Timer Count (REMM #1, Relay #4)

Cmd Loc 022

Default

Range

1 - 255

Comments

Timer Units (REMM #1, Relay #5)

For REMM #1, Relay #5, CL 023 stores the units, while

CL 024 stores the starting count. The timer will count

backwards and when it reaches 0, the respective relay

will open.

Cmd Loc 023

Default

Range

1 - 5

Timer Count (REMM #1, Relay #5)

Cmd Loc 024

Default

Range

1 - 255

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 7 - Auxiliary Devices Programming (cont.)

Options:

Comments

Timer Units (REMM #2, Relay #1)

Latched

For REMM #2, Relay #1, CL 025 stores the units, while

CL 026 stores the starting count. The timer will count

backwards and when it reaches 0, the respective relay

will open.

Cmd Loc 025

Seconds

Minutes

Hours

Default

Range

1 - 5

Timer Count (REMM #2, Relay #1)

Cmd Loc 026

Days

NOTE: The timer function is ignored if the Relay option (Block 7, CL 001 -

011) is programmed for SpreadNet Arming/Disarming (option #5), Listen-In

Trigger (option #9), Follows Keypad Sounder (option #10), Relay Status #1

(option #67), Relay Status #2 (option #68), 3-second Toggle for Audible

Shutoff (option #72), or 3-second Toggle for Local Bell Test (option #73).

Default

Range

1 - 255

Comments

Timer Units (REMM #8, Relay #2)

For REMM #2, Relay #2, CL 027 stores the units, while

CL 028 stores the starting count. The timer will count

backwards and when it reaches 0, the respective relay

will open.

Cmd Loc 027

Default

Range

1 - 5

Timer Count (REMM #2, Relay #2)

Cmd Loc 028

Default

Range

1 - 255

Comments

Timer Units (REMM #2, Relay #3)

For REMM #2, Relay #3, CL 029 stores the units, while

CL 030 stores the starting count. The timer will count

backwards and when it reaches 0, the respective relay

will open.

Cmd Loc 029

Default

Range

1 - 5

Timer Count (REMM #2, Relay #3)

Cmd Loc 030

Default

Range

1 - 255

Comments

Timer Units (REMM #2, Relay #4)

For REMM #2, Relay #4, CL 031 stores the units, while

CL 032 stores the starting count. The timer will count

backwards and when it reaches 0, the respective relay

will open.

Cmd Loc 031

Default

Range

1 - 5

Timer Count (REMM #2, Relay #4)

Cmd Loc 032

Default

Range

1 - 255

Comments

Timer Units (REMM #2, Relay #5)

For REMM #2, Relay #5, CL 033 stores the units, while

CL 034 stores the starting count. The timer will count

backwards and when it reaches 0, the respective relay

will open.

Cmd Loc 033

Default

Range

1 - 5

Timer Count (REMM #2, Relay #5)

Cmd Loc 034

Default

Range

1 - 255

Relay Activation By Zone (Zones 1 - 32)

Comments

Options:

Cmd Loc 035 036 037 038 039 040 041 042

These Options determine which relay(s) are

activated following an alarm on a specific

zone. Each relay may be specified by one or

more zones.

No Relay Activation

Zone #

Cmd Loc 043 044 045 046 047 048 049 050

Zone # 10 11 12 13 14 15 16

Cmd Loc 051 052 053 054 055 056 057 058

Zone # 17 18 19 20 21 22 23 24

Cmd Loc 059 060 061 062 063 064 065 066

On Board Relay

REMM #1, Relay #1

REMM #1, Relay #2

REMM #1, Relay #3

REMM #1, Relay #4

REMM #1, Relay #5

REMM #2, Relay #1

REMM #2, Relay #2

REMM #2, Relay #3

The specific relay (Block 7, CL 001 - 011)

must be programmed for zone activation (Op-

tion #74).

Zone #

Default

Range

0 (All CL)

0 - 11 (All CL)

28 29 30 31

10 REMM #2, Relay #4

11 REMM #2, Relay #5

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 7 - Auxiliary Devices Programming (cont.)

Comments

Options: (CL 067)

Timed Relay Closing (Timer #1 - Day of Week)

These Options will determine the Day(s) of

the Week and Time of Day when the pro-

grammed relay will automatically close. The

value programmed into CL 067 is the total for

all days the relay is to be activated. The relay

to be closed is programmed in Block 7, CL

001 - 011 using Option 79.

Disabled

Saturday

Friday

Thursday

Wednesday

Cmd Loc 067

Default

Range

0 - 127

Timed Relay Closing (Timer #1 - Hours)

Cmd Loc 068

16 Tuesday

32 Monday

64 Sunday

Default

Range

0 - 23

Once activated, the relay will remain closed

for the amount of time programmed into the

countdown timer for the specific relay (Block

7, CL 013 - 034).

Timed Relay Closing (Timer #1 - Minutes)

Cmd Loc 069

Default

Range

0 - 59

Comments

Options: (CL 070)

Timed Relay Closing (Timer #2 - Day of Week)

These Options will determine the Day(s) of

the Week and Time of Day when the pro-

grammed relay will automatically close. The

value programmed into CL 070 is the total for

all days the relay is to be activated. The relay

to be closed is programmed in Block 7, CL

001 - 011 using Option 80.

Cmd Loc 070

Disabled

Saturday

Friday

Thursday

Wednesday

Default

Range

0 - 127

Timed Relay Closing (Timer #2 - Hours)

Cmd Loc 071

16 Tuesday

32 Monday

64 Sunday

Default

Range

0 - 23

Once activated, the relay will remain closed

for the amount of time programmed into the

countdown timer for the specific relay (Block

7, CL 013 - 034).

Timed Relay Closing (Timer #2 - Minutes)

Cmd Loc 072

Default

Range

0 - 59

Comments

Options: (CL 073)

Timed Relay Closing (Timer #3 - Day of Week)

These Options will determine the Day(s) of

the Week and Time of Day when the pro-

grammed relay will automatically close. The

value programmed into CL 073 is the total for

all days the relay is to be activated. The relay

to be closed is programmed in Block 7, CL

001 - 011 using Option 81.

Disabled

Saturday

Friday

Thursday

Wednesday

Cmd Loc 073

Default

Range

0 - 127

Timed Relay Closing (Timer #3 - Hours)

Cmd Loc 074

16 Tuesday

32 Monday

64 Sunday

Default

Range

0 - 23

Once activated, the relay will remain closed

for the amount of time programmed into the

countdown timer for the specific relay (Block

7, CL 013 - 034).

Timed Relay Closing (Timer #3 - Minutes)

Cmd Loc 075

Default

Range

0 - 59

Comments

Options: (CL 076)

Timed Relay Closing (Timer #4 - Day of Week)

These Options will determine the Day(s) of

the Week and Time of Day when the pro-

grammed relay will automatically close. The

value programmed into CL 076 is the total for

all days the relay is to be activated. The relay

to be closed is programmed in Block 7, CL

001 - 011 using Option 82.

Cmd Loc 076

Disabled

Saturday

Friday

Thursday

Wednesday

Default

Range

0 - 127

Timed Relay Closing (Timer #4 - Hours)

Cmd Loc 077

16 Tuesday

32 Monday

64 Sunday

Default

Range

0 - 23

Once activated, the relay will remain closed

for the amount of time programmed into the

countdown timer for the specific relay (Block

7, CL 013 - 034).

Timed Relay Closing (Timer #4 - Minutes)

Cmd Loc 078

Default

Range

0 - 59

Comments

Options:

Number of REMMs

This option determines where panel events are stored.

0 = No REMMs installed, all events are stored in the

control panel’s event memory (60 events maxi-

mum).

None

Cmd Loc

Default

Range

079

0 - 2

REMM 1 only

REMM 1 and 2

1 = REMM #1 installed. Control panel events will be

stored in the REMM (250 events maximum).

2 = Both REMM #1 and REMM #2 are installed.

Control panel events will be stored using a both

REMMs (500 events maximum).

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 8 - SpreadNet Programming

The SpreadNet Programming Block has a total of 45 Command Locations (CL 001 - 045). The SpreadNet transmitters

must be programmed with the SpreadNet Programmer. Refer to the Sierra Reference Manual for additional information.

SpreadNet Channel

Cmd Loc 001

Comments

The Spread Spectrum channel used by the system.

Default

Range

1 - 2

SpreadNet Property Code

Cmd Loc 002 003 004 005

Comments

Unique Property Code used to identify a transmitter as being part of the

system. Program one digit per Cmd Loc.

Default

Range

0001

0001 - 4048

SpreadNet Zone Transmitter Supervisory Rates

(Zones 1 - 32)

Comments

Options:

The Supervisory Rate is the time interval

between transmitter check-ins. A total of

eight consecutive supervisory check-ins

must be missed before a supervisory fail-

ure is reported.

Unsupervised, Battery

status sent hourly

30 seconds

Cmd Loc 006 007 008 009 010 011 012 013

Zone #

Cmd Loc 014 015 016 017 018 019 020 021

Zone # 10 11 12 13 14 15 16

Cmd Loc 022 023 024 025 026 027 028 029

Zone # 17 18 19 20 21 22 23 24

Cmd Loc 030 031 032 033 034 035 036 037

120 seconds

300 seconds

If option 1 is selected, unsupervised transmitters will send battery status

hourly, only if they are within range of the receiver. Transmitters which are

out of range will not be reported as missing, because they are unsu-

pervised.

Zone #

Default

Range

1 (All CL)

1 - 4 (All CL)

29 30 31

SpreadNet Keypad Supervisory Rate

(Keypads 1 - 8)

Cmd Loc

Keypad #

Default

038 039 040 041 042 043 044 045

1 (All CL)

1 - 4 (All CL)

Range

Block 9 - Partition (Area) Programming

This Block has 178 Command Locations (CL 001 - 178) and is used to define all partition information, including which

zones, user codes, and keypads are assigned to each partition. SpreadNet SN991-REMOTEs and SN961-KEYFOBs are

associated with a specific user number and both sections must be programmed for them to function.

Partition Type

Comments

Options:

Cmd Loc 001

This option is used to specify whether or

not a partitioned system has a common

area and the type of display used in the

common area.

No Common Area

Default

Range

1 - 3

Common Area - Full

View Keypad

Common Area - Limited

View Keypad

Zone Assignments to Areas (Zones 1 - 32)

Comments

Each zone may be individually assigned to an

Area (Partition) or disabled.

Options:

Cmd Loc 002 003 004 005 006 007 008 009

Zone Disabled

Area 1

Area 2

Area 3

Area 4

Area 5

Area 6

Area 7

Area 8

Zone #

Cmd Loc 010 011 012 013 014 015 016 017

Zone # 10 11 12 13 14 15 16

Cmd Loc 018 019 020 021 022 023 024 025

Zone # 17 18 19 20 21 22 23 24

Cmd Loc 026 027 028 029 030 031 032 033

Zone #

Default

Range

1 (All CL)

0 - 8 (All CL)

29 30 31

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 9 - Partition (Area) Programming (cont.)

Area Access by User Number (User # 1 - 60)

Comments

Options:

Cmd Loc 034 035 036 037 038 039 040 041

If common area is enabled, then area 1 must

be active for each user who requires access to

the common area.

Area 1(Common

User #

Cmd Loc 042 043 044 045 046 047 048 049

User # 10 11 12 13 14 15 16

Cmd Loc 050 051 052 053 054 055 056 057

User # 17 18 19 20 21 22 23 24

Cmd Loc 058 059 060 061 062 063 064 065

User # 25 26 27 28 29 30 31 32

Cmd Loc 066 067 068 069 070 071 072 073

User # 33 34 35 36 37 38 39 40

Cmd Loc 074 075 076 077 078 079 080 081

User # 41 42 43 44 45 46 47 48

Cmd Loc 082 083 084 085 086 087 088 089

User # 49 50 51 52 53 54 55 56

Cmd Loc 090 091 092 093

User # 57 58 59 60

Area, if enabled)

Area 2

Area 3

Assigned user codes, if used:

System Master Code - user #1

Kidwatch Code - user #11

Area Masters

Area 1 - user #12

Area 2 - user #16

Area 3 - user #20

Area 4 - user #24

Area 4

16 Area 5

32 Area 6

64 Area 7

128 Area 8

Area 5 - user #28

Area 6 - user #32

Area 7 - user #36

Area 8 - user #40

Maid Codes

Area 1 - user #13

Area 2 - user #17

Area 3 - user #21

Area 4 - user #25

Area 5 - user #29

Area 6 - user #33

Area 7 - user #37

Area 8 - user #41

Default 255 (CL 034), 1 (All Other Locations)

Range 1 - 255 (All Locations)

Relay Activation Codes

Area 1 - user #14

Area 2 - user #18

Area 3 - user #22

Area 4 - user #26

Area 5 - user #30

Area 6 - user #34

Area 7 - user #38

Area 8 - user #42

Duress Codes

Area 1 - user #15

Area 2 - user #19

Area 3 - user #23

Area 4 - user #27

Area 5 - user #31

Area 6 - user #35

Area 7 - user #39

Area 8 - user #43

Keypad Assignments to Areas (Keypads 1 - 16)

Options:

Comments

Cmd Loc 094 095 096 097 098 099 100 101

Disabled

Area 1

Area 2

Area 3

Area 4

Area 5

Area 6

Area 7

Area 8

Each keypad may be assigned to any area

(partition) or designated as a Common Key-

pad.

Keypad #

Cmd Loc 102 103 104 105 106 107 108 109

Keypad #

Default

Range

1 (All Locations)

0 - 9 (All Locations)

NOTE: Only Alphanumeric keypads may be

designated as Common Keypads.

Common Keypad

Options:

First to Open/Last to Close Enable

Comments

Cmd Loc 110

If enabled (programmed as 2), the first user to disarm any

area will send an opening report to the central station. The

last user to arm any area will send the closing report. The

user must be authorized to send opening/closing reports

(Block 1, CL 021 - 080).

Yes

Default

Range

1 - 2

Area Assignments (SpreadNet Keypads 1 - 8)

Comments

Options:

Cmd Loc 111 112 113 114 115 116 117 118

If the system is divided into areas, this option deter-

mines the area(s) associated with each SpreadNet

SN990-KEYPAD. SpreadNet keypads arm and dis-

arm all assigned areas at the same time. The value

programmed into the specific location is the total of

all areas the keypad will be able to access. To send

a Panic report from a SpreadNet keypad, the Police

Soft Zone (Block 2, CL 156) must also be enabled.

Disabled

Area 1

Area 2

Area 3

Area 4

Keypad #

Default

0 (All Locations)

0 - 255 (All Locations)

Range

16 Area 5

32 Area 6

64 Area 7

128 Area 8

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 9 - Partition (Area) Programming (cont.)

Area Access (SN Keyfob/Remote # 1 - 60)

Comments

Options:

Cmd Loc 119 120 121 122 123 124 125 126

If the system is divided into areas, this option deter-

mines the area(s) associated with each SpreadNet

SN991-REMOTE or SN961-KEYFOB. The SpreadNet

remotes and keyfobs are associated with a specific

user number and will arm or disarm all assigned areas

at the same time. The value programmed into the spe-

cific location is the total of all areas the remote/keyfob

will be able to access. To send a Panic report from a

keyfob or remote, the Police Soft Zone (Block 2, CL

156) must also be enabled.

Disabled

User #

Cmd Loc 127 128 129 130 131 132 133 134

User # 10 11 12 13 14 15 16

Cmd Loc 135 136 137 138 139 140 141 142

User # 17 18 19 20 21 22 23 24

Cmd Loc 143 144 145 146 147 148 149 150

User # 25 26 27 28 29 30 31 32

Cmd Loc 151 152 153 154 155 156 157 158

User # 33 34 35 36 37 38 39 40

Cmd Loc 159 160 161 162 163 164 165 166

User # 41 42 43 44 45 46 47 48

Cmd Loc 167 168 169 170 171 172 173 174

User # 49 50 51 52 53 54 55 56

Cmd Loc 175 176 177 178

User # 57 58 59 60

Default 1 (All Locations)

Range 0 - 255 (All Locations)

Area 1

Area 2

Area 3

Area 4

16 Area 5

32 Area 6

64 Area 7

128 Area 8

NOTE: If the user code for the specific user number is

disabled, the remote or keyfob will not work. The

SN991-REMOTE or SN961-KEYFOB may be assigned

to any or all areas to which the user has authority (see

Block 9, CL 034 - 093).

Block 10 - User Code Programming

User Codes (User # 1 - 60)

Comments

Cmd Loc

User #1

Cmd Loc

User #2

001 002 003 004

Each user code is a 4-digit code which may be used to arm and

disarm the system or to bypass zones. Valid entries are the digits

0 - 9. To disable a user code, enter 0-0-0-0 (default code for all

user codes except user #1).

System Master Code

005 006 007 008

Cmd Loc

User #3

Cmd Loc

User #4

009 010 011 012

User code authority is programmed in Block 1, CL 021 - 080.

User codes are programmed with 1 digit per Cmd Loc.

013 014 015 016

Cmd Loc

User #5

Cmd Loc

User #6

017 018 019 020

021 022 023 024

Cmd Loc

User #7

Cmd Loc

User #8

025 026 027 028

029 030 031 032

Cmd Loc

User #9

033 034 035 036

Cmd Loc

User #10

Cmd Loc

User #11

Cmd Loc

User #12

Cmd Loc

User #13

Cmd Loc

User #14

Cmd Loc

User #15

Cmd Loc

User #16

Cmd Loc

User #17

Cmd Loc

User #18

Cmd Loc

User #19

Cmd Loc

User #20

Cmd Loc

User #21

037 038 039 040

041 042 043 044

045 046 047 048

049 050 051 052

053 054 055 056

057 058 059 060

061 062 063 064

065 066 067 068

069 070 071 072

Kidwatch Code

Area 1 Master Code

Area 1 Maid Code

Area 1 Relay Code

Area 1 Duress Code

Area 2 Master Code

Area 2 Maid Code

Area 2 Relay Code

073 074 075 076

077 078 079 080

081 082 083 084

Area 2 Duress Code

Area 3 Master Code

Area 3 Maid Code

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 10 - User Code Programming (cont.)

User Codes (cont.)

Comments

Cmd Loc

User #22

Cmd Loc

User #23

Cmd Loc

User #24

Cmd Loc

User #25

Cmd Loc

User #26

Cmd Loc

User #27

Cmd Loc

User #28

Cmd Loc

User #29

Cmd Loc

User #30

Cmd Loc

User #31

Cmd Loc

User #32

Cmd Loc

User #33

Cmd Loc

User #34

Cmd Loc

User #35

Cmd Loc

User #36

Cmd Loc

User #37

Cmd Loc

User #38

Cmd Loc

User #39

Cmd Loc

User #40

Cmd Loc

User #41

Cmd Loc

User #42

Cmd Loc

User #43

Cmd Loc

User #44

Cmd Loc

User #45

Cmd Loc

User #46

Cmd Loc

User #47

Cmd Loc

User #48

Cmd Loc

User #49

Cmd Loc

User #50

Cmd Loc

User #51

Cmd Loc

User #52

Cmd Loc

User #53

085 086 087 088

Each user code is a 4-digit code which may be used to arm and

disarm the system or to bypass zones. Valid entries are the digits

0 - 9. To disable a user code, enter 0-0-0-0 (default code for all

user codes except user #1).

Area 3 Relay Code

Area 3 Duress Code

Area 4 Master Code

089 090 091 092

093 094 095 096

097 098 099 100

101 102 103 104

105 106 107 108

109 110 111 112

113 114 115 116

117 118 119 120

121 122 123 124

125 126 127 128

129 130 131 132

133 134 135 136

137 138 139 140

141 142 143 144

145 146 147 148

149 150 151 152

153 154 155 156

157 158 159 160

161 162 163 164

165 166 167 168

169 170 171 172

173 174 175 176

177 178 179 180

181 182 183 184

185 186 187 188

189 190 191 192

193 194 195 196

197 198 199 200

201 202 203 204

205 206 207 208

209 210 211 212

User code authority is programmed in Block 1, CL 021 - 080.

User codes are programmed with 1 digit per Cmd Loc.

Area 4 Maid Code

Area 4 Relay Code

Area 4 Duress Code

Area 5 Master Code

Area 5 Maid Code

Area 5 Relay Code

Area 5 Duress Code

Area 6 Master Code

Area 6 Maid Code

Area 6 Relay Code

Area 6 Duress Code

Area 7 Master Code

Area 7 Maid Code

Area 7 Relay Code

Area 7 Duress Code

Area 8 Master Code

Area 8 Maid Code

Area 8 Relay Code

Area 8 Duress Code

Download from Www.Somanuals.com. All Manuals Search And Download.

Block 10 - User Code Programming (cont.)

User Codes (cont.)

Comments

Cmd Loc

User #54

Cmd Loc

User #55

Cmd Loc

User #56

Cmd Loc

User #57

Cmd Loc

User #58

Cmd Loc

User #59

Cmd Loc

User #60

213 214 215 216

Each user code is a 4-digit code which may be used to arm and

disarm the system or to bypass zones. Valid entries are the digits

0 - 9. To disable a user code, enter 0-0-0-0 (default code for all

user codes except user #1).

217 218 219 220

221 222 223 224

225 226 227 228

229 230 231 232

233 234 235 236

237 238 239 240

User code authority is programmed in Block 1, CL 021 - 080.

User codes are programmed with 1 digit per Cmd Loc.

Download from Www.Somanuals.com. All Manuals Search And Download.

C & K is a registered trademark of C & K Components

Sierra and SpreadNet are registered trademarks of C & K Systems, Inc.

www.cksys.com

All other trademarks are the property of their respective owners.

P/N 5-051-533-16 Rev A

Download from Www.Somanuals.com. All Manuals Search And Download.

SIIG Computer Drive 5052 User Manual
Sony Car Speaker L1036 User Manual
Sony Trimmer PCS G70 User Manual
Speco Technologies Security Camera CVC 770PH User Manual
Speco Technologies Security Camera CVC5845DNV User Manual
Star Trac Treadmill CTEN1010 U08841 User Manual
Subaru Robin Power Products Automobile Parts EY15 2B User Manual
Sylvania TV VCR Combo 6720FDF User Manual
Tanita Computer Monitor BC 554 User Manual
Tanita Scale BF 555 User Manual