Shure Headphones SE112 User Manual

SE112 Sound Isolating™ Earphones  
Choosing a Sleeve  
Cleaning the Nozzle  
Soft flex sleeves are included in small, medium, and large sizes.  
Select an earphone sleeve that provides the best fit and sound  
isolation. It should be easy to insert, fit comfortably, and easy  
to remove.  
If you notice a change in sound quality, remove the sleeve and  
check the nozzle of your earphone. If nozzle is blocked, clear  
obstruction by using wire loop end of cleaning tool.  
Wearing the Earphones  
The following are some suggested ways of wearing the  
earphones.  
Nozzle  
Soft Flex Sleeves  
Nozzle Cleaning Tool  
Warning: The cleaning tool is only to be used to clean the  
earphones. Any other use, such as using the tool to clean ears,  
could result in injury.  
Over the ear  
Using the Remote (m+  
models only)  
Inserting the Earphones  
Maintenance and Cleaning  
Careful maintenance ensures a tight seal between the sleeve  
and nozzle, improving sound quality and product safety.  
Use the remote to control compatible media phone players.  
Insert the earphones so they form a tight seal. The fit of the ear-  
phone can greatly affect sound quality.  
Keep the earphones and sleeves as clean and dry as  
possible.  
Play music  
Click the center button once  
Click the center button once.  
To clean sleeves, remove them from earphones, gently rinse  
in warm water and air dry. Foam sleeves require a longer  
drying time. Inspect for damage and replace if necessary.  
Ear sleeves must be completely dry before reusing.  
Pause music  
Change volume Click the volume up (+) or volume down (-)  
button to increase or decrease the volume.  
Wipe the earphones and sleeves with mild antiseptic to avoid  
infections. Do not use alcohol-based disinfectants.  
Go to next  
track  
Double-click the center button.  
Triple-click the center button.  
Triple-click after 6 seconds.  
Important: If there seems to be a lack of low frequency  
response (bass), this means that the earphone sleeve is not  
forming a tight seal. Gently push the earphone deeper into the  
ear canal or try a different sleeve.  
Do not expose earphones to extreme temperatures.  
Replace sleeves if they do not fit properly.  
Go to previous  
track  
Do not attempt to modify this product. Doing so will void the  
warranty and could result in personal injury and/or product  
failure.  
Restart current  
track  
Warning: Do not push the earphone sleeve beyond the ear  
canal opening.  
Fast-forward  
Double-click and hold the center button.  
Click the center button once.  
Send/End Call  
Accessories  
For more information about compatible models go to: www.  
shure.com  
Removing the Earphones  
For information about earphone accessories and other Shure  
products visit:  
Grasp the body of earphone and gently twist to remove.  
“Made for iPod,” “Made for iPhone,” and “Made for iPad”  
mean that an electronic accessory has been designed to  
connect specifically to iPod, iPhone, or iPad, respectively,  
and has been certified by the developer to meet Apple per-  
formance standards. Apple is not responsible for the oper-  
ation of this device or its compliance with safety and regu-  
latory standards. Please note that the use of this accessory  
with iPod, iPhone, or iPad may affect wireless performance.  
Furnished accessories subject to change.  
Certifications  
iPad, iPhone, iPod, iPod classic, iPod nano, iPod touch, and  
Retina are trademarks of Apple Inc., registered in the U.S. and oth-  
er countries. iPad Air and iPad mini are trademarks of Apple Inc.  
The trademark “iPhone” is used with a license from Aiphone K.K.  
This product meets the Essential Requirements of all relevant  
European directives and is eligible for CE marking.  
Note: Do not pull on cable to remove earphone.  
The CE Declaration of Conformity can be obtained from: www.  
shure.com/europe/compliance  
Changing Sleeves  
Authorized European representative:  
Shure Europe GmbH  
Twist and pull to remove the sleeve from the nozzle.  
Headquarters Europe, Middle East & Africa  
Department: EMEA Approval  
Jakob-Dieffenbacher-Str. 12  
75031 Eppingen, Germany  
Phone: 49-7262-92 49 0  
Slide on a new sleeve so that it completely covers the barb  
and the nozzle.  
Fax: 49-7262-92 49 11 4  
Caution: If the barb or any of the nozzle is exposed, the  
sleeve is not properly installed. Replace sleeves if they do not  
tightly grip the nozzle. To ensure proper fit and performance, use  
only sleeves supplied by Shure (unless using custom molded  
sleeves).  
©2014 Shure Incorporated  
27A25176 (Rev. 3)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Shure Mixer A68B User Manual
Soleus Air Air Conditioner GM WAC 25ESE C User Manual
Sony Home Theater Screen SDM HS75 User Manual
Sony MP3 Player TCM 900DV User Manual
Sony Printer DMP 1000 User Manual
Speco Technologies VCR TRV 960 User Manual
Splendide Washer Dryer WD2100 User Manual
StarTechcom Power Supply ATX12V22 User Manual
Sterling Plumbing Product BP1012 User Manual
Stiga Lawn Mower 11 5234 53 User Manual