Compact Scooters
XtraLite 4
(TE-787NA-UL4)
XtraLite 3
(TE-787NA-UL3)
Scootie
(TE-787NA)
Sunrunner S
(777-3/4)
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Congratulations on your purchase of the Shoprider® scooter. This scooter incorporates the latest
innovative designs patented and only available on a Shoprider® scooter. This scooter can be
used in confined spaces both indoors and out. Direct drive transaxles and electromagnetic brakes
give a safe and efficient ride. This Shoprider® scooter is designed for persons with limited
mobility.
Please ensure that you read this manual carefully, it is important for your safety that you
understand the guidelines and instructions given.
FEATURE GUIDE (FIG. 1-4)
1
2
6
XtraLite 3 (Figure 1)
3
1. Tiller control head
2. Detachable seat with fold down back
3. Detachable basket
3
4
4. Detachable battery
5. Tiller release knob
6. Carrying stay rod
5
7. Seat height adjustment
8. Puncture proof tires
7
8
Figure 1
1
2
XtraLite 4 (Figure 2)
3
1. Tiller control head
2. Detachable seat with fold down back
3. Detachable basket
4
5
4. Detachable battery
5. Tiller angle adjustment
6. Seat height adjustment
7. Anti-Tip wheels
7
8. Puncture proof tires
6
8
Figure 2
9/22/2004
3
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
Scootie (Figure 3)
1. Tiller control head
6
2. Detachable seat with fold down back
3. Detachable basket
3
4. Detachable cover with integral battery pack
5. Tiller release knob
8
6. Carrying stay rod
7. Seat height adjustment
8. Anti-Tip wheels
9. Puncture proof tires
5
4
9
7
Figure 3
Sunrunner S (Figure 4)
1
2
1. Tiller control head
2. Detachable swivel seat with fold down back
3. Detachable basket
4. Detachable cover with integral battery pack
5. Tiller angle adjustment
6. Seat height adjustment
3
5
7. Puncture proof tires
6
7
4
Figure 4
9/22/2004
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY ADVICE
• Do not carry passengers.
• Do not exceed inclines over 8 degrees (14% grade).
• Do not turn on steep inclines.
• Do not turn suddenly at high speeds.
• Do not get on or off the scooter unless the brake is on and the scooter is switched off.
• Do not switch off the scooter while the scooter is moving.
• Do not drive the scooter where you can not safely or legally walk.
• Do not attempt to drive over curbs greater than 2 inches (5cm.) in height. Doing so could cause
your scooter to turn over, causing injury or damage to the scooter. For curbs less than 2 inches,
always approach them at an angle of 90 degrees and at a low speed.
• Do not drink or use a mobile phone when driving your scooter.
• Do not exceed the suggested user weight limit. Doing so, could cause personal injury and
invalidate the warranty.
• Always keep your feet on the scooter when moving.
• Consult your doctor if there is any doubt about your ability to use a scooter safely.
• Always slow down and proceed carefully when traveling over rough or uneven ground.
• For individuals with balance problems practice getting on the scooter with assistance of a
qualified healthcare professional.
• If equipped, DO NOT operate the scooter without anti-tip wheels installed.
• Do not use an escalator to move a scooter between floors. Serious injury could occur.
• Do not drive the scooter on an incline that has oil, water or ice film on it.
• Do not try to lift the scooter by its seat, tiller, rear chassis cover, or any removable parts. Any
of these could cause injury to the user or damage to the scooter.
• Do not use parts or accessories that are not authorized by Shoprider® Mobility Products, Inc.
• Before sitting in or exiting the scooter, REMOVE the key from the ignition. This will insure
the POWER is off and the scooter can not move under its own power.
• As a general precaution, always remove the key from the ignition while the scooter is not in
use. This will prevent use by untrained and unauthorized persons.
• Do not connect any medical device to the scooter battery. This could cause failure of the
device, the scooter and personal injury.
• Make sure the tiller is properly adjusted to the user or damage and injury could result.
• Shoprider® Mobility Products, Inc. does not recommend that scooter users be transported in a
vehicle WHILE they are in the scooter…and will not be responsible for any injury or damage
that might result.
• Do not use the scooter in the rain, near a shower or in a damp bathroom. Direct exposure to
rain or dampness could cause the scooter to electrically malfunction and prematurely rust.
• For maximum battery life, make sure to fully charge batteries for 8 hours prior to usage.
9/22/2004
5
Download from Www.Somanuals.com. All Manuals Search And Download.
EMI Warning
Shoprider® scooters may be susceptible to electromagnetic interference (EMI), which is a kind
of interfering electromagnetic energy (EM) emitted from sources such as radio stations, TV
stations, amateur radio (HAM) transmitters, two-way radio, and cellular phones. The
interference (from radio wave sources) can cause the scooter to release its brakes, move by itself,
or move in unintended directions. It can also permanently damage the scooter’s control system.
The sources of radiated EMI can be broadly classified into three types:
1. Hand-held portable transceivers (transmitters-receivers) with the antenna mounted directly on
the transmitting unit. Examples include: citizens band (CB) radios, “walkie talkie”, security,
fire and police transceivers, cellular telephones, and other personal communication devices.
NOTE! Some cellular telephones and similar devices transmit signals while they are ON,
even when not being used.
2. Medium-range mobile transceivers, such as those used in police cars, fire trucks, ambulances,
and taxis. These usually have the antenna mounted on the outside of the vehicle.
3. Long-range transmitters and transceivers, such as commercial broadcast transmitters (radio
and TV broadcast antenna towers) and amateur (HAM) radios.
NOTE! Other types of hand-held devices, such as cordless phones, laptop computers,
AM/FM radios, TV sets, CD players, and cassette players, and small appliances, such as
electric shavers and hair dryers, so far as we know, are not likely to cause problems to the
scooter.
Scooter Electromagnetic Interference (EMI)
Because EM energy rapidly becomes more intense as one moves closer to the transmitting
antenna (source), the EM fields from hand-held radio sources (transceivers) are of special
concern. It is possible to unintentionally bring high levels of EM energy very close to the
scooter’s control system while using these devices. This can affect scooter movement and
braking. Therefore, the warnings listed below are recommended to prevent possible interference
with the control system of the scooter.
WARNINGS
1. Do not operate hand-held transceivers (transmitters-receivers), such as citizens band (CB)
radios, or turn ON personal communication devices, such as cellular phones, while the scooter
is turned ON.
2. Be aware of nearby transmitters, such as radio or TV stations, and try to avoid coming close
to them.
3. If unintended movement or brake release occurs, turn the scooter OFF as soon as it is safe.
4. Be aware that adding accessories or components, or modifying the scooter may make it more
susceptible to EMI.
NOTE! There is no easy way to evaluate the overall immunity of the scooter.
5. Report all incidents of unintended movement or braking to your Shoprider® dealer, and note
whether there are sources of EMI nearby.
WARNING: Shoprider® Mobility Products, Inc. is not responsible for damage or injury
incurred due to improper and unsafe use of our scooter.
9/22/2004
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
Tiller Angle Adjustment (For XtraLite 4
& Sunrunner S ONLY) (Fig. 5)
On the left hand side at the base of the tiller
is a red lever. Push the lever in to release
the pin and select the required tiller angle.
Refit the pin into one of the five location
holes.
Tiller Angle
Adjustment
Lever
Folding the Tiller (For XtraLite 3 &
Scootie ONLY) (Fig. 6)
Figure 5
Fold down the tiller by loosening the hand
knob located at the base of the tiller stem.
Seat Slide & Swivel Adjustment (For
Sunrunner S ONLY) (Fig. 7)
Pulling up on the lever allows the seat
position to be adjusted forward or backward.
Release the lever and the seat will lock in
that position. Under the right side of the
seat there is a spring loaded red lever.
Pulling up on the lever allows the seat to
swivel, when released the seat will lock into
one of 4 positions.
Tiller Hand
Knob
Figure 6
Figure 7
Seat Removal (Fig. 8)
Swivel Seat
Adjustment
Lever
Seat Slide
Lever
Fold down the back of the seat. Remove the
seat hand knob and locking pin that secures
the seat adaptor. Lift the seat adaptor out of
the seat post.
Seat Height Adjustment (Fig. 8)
Remove seat as described above. Loosen
the lower hand knob. The seat height can be
adjusted to 5 different settings by inserting
the steel locking pin in the required hole.
Retighten the lower hand knob and replace
the seat.
Seat
Adaptor
Seat
Locking Pin
Seat
Tightening
Hand Knob
Figure 8
Do not use the scooter without the arms
being fitted.
9/22/2004
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Armrest Width Adjustments (Fig. 9)
On the underside of the seat there are two hand
knobs, one on each side. Loosening the arm rest
tightening knob allows the armrest width to be
adjusted or arm rests to be removed.
Arm Rest
Adjustment
Hand Knob
Armrest Angle Adjustment (Fig. 10)
Flip up the armrests to allow access to the
adjustment screw and lock nut, unscrew the lock
nut and screw the bolt in or out to increase or
decrease the angle. Re-tighten the lock-nut.
Your scooter is dispatched from the factory with
the armrests set parallel to the floor.
Figure 9
Adjustment
Screw
Locking Nut
and Bolt
Scooter Length Adjustment (For Scootie &
Sunrunner S ) (Fig. 11)
The wheel base can be lengthened or shortened
depending on its existing settings. The standard
length of the scooter can be extended up to 3
inches. To adjust the wheelbase, remove the
seat and the chassis cover complete with
integral batteries. Remove the locking pin
located at the front of the seat post (Fig. 8).
Unscrew the red hand lever in front of the pin
by turning counter-clockwise. Loosen the clips
that secure the wires along the chassis. Slide the
inner front section until the location holes
become aligned. Insert the locking pin and
tighten the red hand lever, insuring when fully
secured, the lever is facing the seat post as
shown in Fig. 11. Replace the chassis cover with
the integral batteries then replace the seat.
Figure 10
Wheel Base
Locking Pin
Figure 11
Scooter Width Adjustment (For XtraLite 3)
(Fig. 12)
Remove seat as described above. Remove rear
basket. Remove U-shaped pins, adjust wheels
to proper hole. Replace U-shaped pins.
U- Shaped
pins
Caution – Width of the wheels MUST be
adjusted evenly on both sides to avoid injury.
Extend both
sides up to 3
inches.
Figure 12
9/22/2004
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SCOOTER TILLER CONTROLS (FIG. 13)
Speed Controls
The speed control allows you to set a speed between 1 (minimum) and 10 (maximum).
Battery Level Indicator/Gauge
The number of LED bars lit/where the needle sits, shows the amount of charge left in your batteries.
The amount of charge will only show at its true level when the scooter is in drive.
Caution – Do not allow the LED bars/gauge needle to go out completely as complete discharge of
the batteries could cause irreversible damage.
Horn
A yellow button at the rear of the tiller operates the horn.
Thumb Lever Controls
The left thumb lever controls the reverse and the right thumb lever controls the forward motion. The
amount of pressure applied to each lever will determine the speed the scooter travels at. Release the
lever and the scooter will slowly come to a stop and the electromagnetic brake will be applied.
On/Off Key Switch
Insert the key in the right side of the tiller. Turn the key and the LED bars will light up/the needle
will move. For XtraLite 3 and XtraLite 4 make sure to turn on the batteries, and for XtraLite 3 turn
on the scooter by the power button located next to the horn. There is a delay before the thumb lever
control can be operated, while the controller is checking the circuits.
Electromagnetic Brake
The brake is automatically operated when the control levers are pressed or released. There is a slight
delay when the scooter decelerates; this allows the scooter to come to a smooth stop.
Speed Control
Dial
Battery Level
On/Off
Indicator
Key Switch
Thumb Lever
Control (Reverse)
Thumb Lever
Control (Forward)
Horn Button
Figure 13
9
9/22/2004
Download from Www.Somanuals.com. All Manuals Search And Download.
FREE WHEEL OPERATION (FIG. 14)
The free wheel release lever (red handle) is located next to the right rear wheel (Fig. 14). To
disengage the motor, lift up the lever (the scooter can now be pushed). To re-engage the motor push
down on the lever.
WARNING! Always re-engage the free wheeling device after use.
Failure to do so may result in injury.
Anti-tip wheels
The anti-tip wheels are located at the rear of the scooter frame (Fig. 14). The scooter should not be
used unless the anti-tipping wheels are in place.
Shoprider® Mobility Products, Inc. is not responsible for damage or injury incurred due to
improper or misuse of the scooter.
Free Wheel
Lever (Red)
Anti-Tip Wheels
Figure 14
STARTING TO DRIVE YOUR SCOOTER
Getting Started
• Select a level area with plenty of space.
• Mount the scooter, either by lifting the arm and sliding onto the seat or rotate the seat outwards
and then rotate the seat back to face the tiller.
• Adjust the tiller and seat as previously described.
Starting Scooter Movement
• Ensure that you are seated in a comfortable position.
• Turn the key to the on position.
• Your speed setting should be on 1 or 2.
• Push your right hand thumb lever and the scooter will move forward slowly. The harder you
press, the faster the scooter goes but will only reach the speed level that has been selected.
• Release the lever and the scooter will slowly come to a stop as the magnetic brake automatically
engages.
9/22/2004
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Steering
Steering the scooter is light and easy. Ensure when starting off you give a wide clearance when
turning so that the rear wheels clear any obstacle that you are passing. When steering through
limited spaces such as a doorway or when turning around, turn the tiller handles where you want to
go and apply power gently. The scooter will turn very tightly, but will still move with complete
stability as long as the speed is not too high.
Reversing
Before reversing ensure that the area behind is free from any hazards or obstructions. Adjust your
speed setting to a low setting before you reverse. Press the left thumb lever, and steer wide of all
corners and obstacles.
Dismounting
Before dismounting ensure that the key is turned to the off position.
CAUTION: Please ensure that care is exercised when entering
or leaving the scooter and that the tiller and foot rest is not used for support.
EXTRA GUIDELINES IN THE CONTROL OF YOUR SCOOTER
Ramps
The stability of your scooter is governed by several factors such as the seating position, the angle of
the slope and your height and weight. When approaching an incline, do so directly and not at an
angle and where ever possible avoid making turns. When going down a ramp or slope keep the
speed settings to slow. This will ensure there is a safe controlled descent. When the finger levers
are released the scooter will slowly stop.
Caution - Do not turn off the control key while the unit is in motion
Grass and Gravel
Please follow the guidelines given previously and your scooter will perform admirably over many
surfaces. Avoid long grass, loose gravel and sand.
NOTE: You should not operate your scooter in wet weather or on wet surfaces. This may cause
the motor to short out.
9/22/2004
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TRANSPORT / STORAGE
The scooters are designed to be dismantled into separate sections for transportation and storage.
Your scooter can be dismantled into the following sections:
6
1
5
XtraLite 3 (Fig. 15)
3
1) Small Front Basket
2) Large Rear Basket
3) Seat
2
4) Seat Post & Fasteners
5) Battery Pack
6) Fold Down Frame
Figure 15
4
XtraLite 4 (Fig. 16)
6
1) Small Front Basket
2) Large Front Basket
3) Seat
4) Seat Post & Fasteners
5) Battery Pack
5
2
1
3
6) Fold Down Frame
Scootie (Fig. 17)
4
Figure 16
4
6
1) Basket
2) Seat
3) Seat Post & Fasteners
4) Rear Chassis
5) Front Chassis
6) Rear Shroud
5
1
2
Sunrunner S (Fig. 18)
3
1) Basket
2) Seat
Figure 17
4
3) Seat Post & Fasteners
4) Rear Chassis
5) Front Chassis
6) Rear Shroud
5
2
1
6
Figure 18
3
9/22/2004
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Dismantling
1. Remove baskets.
2. Fold down the back of the seat.
3. For Sunrunner S: pull up on the red lever under the seat and at the same time lift and twist the
seat off.
For XtraLite 3; XtraLite 4; Scootie: unscrew the tightening bolt below the seat. Lift seat off.
For XtraLite 3 & XtraLite 4 ONLY.
1. Lower tiller toward the foot rest and connect the carrying rod (For XtraLite 3) to the proper
location or connect the two Velcro straps (For XtraLite 4) to the handle bars.
For Scootie & Sunrunner S ONLY.
2. Remove the rear chassis cover/battery pack.
3. Remove the locking pin and separate the rear drive unit (Fig. 11).
4. Lower the tiller to its lowest level on the front chassis and connect the carrying rod (if the rear
drive unit is NOT separated).
BATTERIES AND BATTERY CHARGER
The Shoprider® scooter is supplied with maintenance free, sealed lead acid batteries. Battery
performance can be affected by temperature, terrain, condition of battery, the weight of the user, etc.
The battery level indicator is only a guide and is most effective when the scooter is moving, only
then is the true discharge level displayed.
• When the scooter stops the battery level indicator may indicate full.
• An active user can use up to 30% of battery capacity or more per day.
• Inactive users may only use 50% of battery capacity in a week.
• In both these instances the battery should be put on charge over night.
Battery Charger
Batteries supplied with your scooter are specially designed. All units require an automatic battery
charger. XtraLite 3 and XtraLite 4 have built in charger ports on the side of the battery pack.
The battery chargers are 2-amp transformer type off board.
Charging
To charge the batteries connect the plug lead into the battery-charging socket on the scooter/battery
pack and the 2 or 3-prong plug into the wall socket and switch on. FOR Scootie and Sunrunner S
ONLY: the battery charger has two lights. The red light when constant shows the battery charger is
connected if the red light flashes; there is a break in the connection. A steady green light will show
the unit is charging. When the light turns solid red again while still plugged into the charging port
the unit is fully charged. DO NOT OVER CHARGE THE UNIT.
FOR XTRALITE 3 & 4: Connect 3 prong round plug to their charging port, located on the side of
the battery pack. The charger will show a solid green light when plugged in the all. Once plugged
into the charging port a steady red light will indicate that the unit is charging. When the red light
turns green while still connected to the charging port, the unit is fully charged. DO NOT OVER
CHARGE THE UNIT.
CAUTION: Always ensure that the charging lead is in good condition and has not been damaged
or stretched.
9/22/2004
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Lubrication
At six-month intervals you should lubricate the following parts with a light oil or similar lubricant:
• Seat pivot post.
• Seat release lever pinion.
• Wheel bearings.
• Axle of scooter.
CAUTION – DO NOT USE WD40 TO LUBRICATE PARTS!! DO NOT LUBRICATE
TRANSAXLE/GEAR BOX!! In the event of any difficulties please consult your dealer.
Wheels and Tires
The wheels of your scooter might have split rims (except for the XtraLite 3 where the rim and tire
are one molded piece together). To change the wheels remove the center bolt and slide the wheel off
its axle. Ensure that when refitting the wheel the retaining bolt is fitted with a locking washer or the
screw threads are treated with lock-tite or a similar adhesive.
TROUBLE SHOOTING GUIDE
Circuit Breaker
Your scooter is fitted with the latest in electronic controls that are programmed to protect the
electrical system from abnormal overloads. Provided for extra protection is a circuit breaker.
Should there be a situation where your scooter stops for no apparent reason, please check that the
circuit breaker has not popped. ON THE SCOOTIE AND SUNRUNNER S the circuit breaker can
be found under the rear chassis cover accessible through a port hole under the seat and can be reset
by pressing the black button. ON THE XTRALITE 3 AND XTRALITE 4 the circuit breaker is
located on the side of the battery pack.
Check List
If your scooter fails to operate, please check the following:
• Unit is switched on.
• All plugs and connectors are clean and firmly connected.
• Battery level shows full charge.
• Freewheeling device is in the drive position.
If the free wheel device has been operated with the scooter switched on, then the scooter will not
operate until the ignition key has been switched off and then on again.
Please consult your dealer if your scooter does not run after checking these points.
9/22/2004
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS
UNIT SPECIFICATIONS
XtraLite 3
XtraLite 4
Scootie
37-40 (930-
1015) x 17 (430)
x 34 (865)
Sunrunner S
43-46 (1090-
1168) x 22
Overall Dimensions: L1 x W x
45 (1130) x 21 (520) x
37 (930)
41 (1040) x 20 (510)
x 35 (890)
in (mm)
H
(560) x 35 (890)
Front
Rear
1 , 8”
2 , 8”
2 , 7”
2 , 8”
2 , 7”
2 , 8”
2 , 8”
2 , 8”
Number, Size of Tires
Suggested User Weight
(on the level road)
lb (kg)
Max. 220 (100)
44 (20)
Max. 220 (100)
53 (24)
Max. 225 (102) Max. 250 (113)
Weight of heaviest part
(w/o battery, baskets and
seat)
25 (11)
40 (18)
lb (kg)
Total Weight (w/ batteries,
basket, seat)
Each Battery Module Weight
79 (36)
22 (10)
89 (41)
18 (8)
82 (37)
22 (10)
130 (59)
20 (9)
lb (kg)
lb (kg)
_V_Ah
x Pcs
Battery Module Capacity
12V12Ah x 2
Off Board (2A)
12V12Ah x 2
Off Board (2A)
12V12Ah x 2
12V12Ah x 2
Off Board (2A) Off Board (2A)
Charger
Output Power of Motor
Maximum Speed2
hp (W)
mph
(km/hr)
0.47 (350)
3.75 (6)
0.45 (336)
3.75 (6)
0.75 (559)
3.50 (6)
0.75 (559)
5 (8)
Maximum Climbing Angle
(based on user weight of
90kg/200lb) /Safe Climbing
Angle
10 (6)/17 (10)
11 (18)
10 (6)/17 (10)
10 (16)
14 (8)
14 (8)
% ( º )
Range3 (per charge w/ STD
12AH Battery / 90
kg User Weight) (After the
battery and
mile
(km)
10 (16)
10 (16)
mechanical moving parts fully
break in)
Turning Radius
Ground Clearance
Handle Bar
in (mm)
in (mm)
Type
39 (1000)
T
46 (1160)
T
40 (1015)
40 (1015)
2
T
3
T
ALL SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.
1.
2.
3.
Include the Anti-Tip wheel.
Driver weight may exceed weight of the unit; speed must be reduced when turning.
The actual driving range varies with the factors shown below:
a) the weight of occupant
b) ground surface
c) battery conditions
d) type of charger
e) ambient temperature
f)
the way of driving
g) etc.
9/22/2004
15
Download from Www.Somanuals.com. All Manuals Search And Download.
QUARTERLY INSPECTION
For your own safety, quarterly inspection and service on the product has to be performed and signed
by an authorized dealer. Maintenance records (below) should be kept at all times. The manufacturer
/ distributor / vendor will be indemnified from any product liability claim if the above maintenance /
service requirement is not met.
NOTE! Regular (Monthly) inspection is strongly recommended by the manufacturer to ensure
ultimate performance of the vehicle.
Service Record:
Date of Purchase:
/
/
Purchaser:__________________ Model #: ____________ Serial #: _______________
Dealer Unit Was Purchased From: _______________________________
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
M / D / Y
9/22/2004
16
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
Please refer to warranty information included with unit.
Serial No.
DISCLAIMER
Congratulations on your purchase of the Shoprider®
It is not intended to be used by individuals with physical limitations that could prevent the user
from operating this unit safely. Shoprider® disclaims all responsibility for any personal injury
or property damage, which may occur as a result of improper or unsafe use of its products.
Mechanical or electrical defects will be dealt with on a contingency liability basis.
The preceding guidelines are intended to assist you in the safe operation of your powered
scooter. If you should have any questions about the correct operation of your scooter, please
contact your authorized Shoprider® dealer.
Model No.
Serial No.
Dealer’s Stamp
Shoprider® Mobility Products, Inc.
(800) 743-0772
9/22/2004
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
9/22/2004
18
Download from Www.Somanuals.com. All Manuals Search And Download.
|