Shindaiwa OwnER’S/OPERaTOR’S ManUaL
PS344 PowerBroomTM
Minimize the risk of injury to yourself and others! Read this
manual and familiarize yourself with the contents. Always wear
eye and hearing protection when operating this unit.
WARNING!
X7502891100
05/10
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
Work Safely
WARNING!
WARNING!
A PowerBroom operates at very high
speeds and has the potential to do serious
damage if misused, abused or mishan-
dled. To reduce the risk of injury, you must
maintain control at all times, and observe
all safety precautions during operation.
Never permit a person without training or
instruction to operate this machine!
Never make unauthorized
attachment installations.
Never operate
power equipment of any kind if
you are tired or if you are under
the influence of alcohol, drugs,
medication or any other substance
that could affect your ability or
judgement.
Stay Alert
You must be physically and mentally fit
to operate this unit safely.
WARNING!
Use Good Judgement
■ Sweeper belts may move when
starting engine. Place sweeper
belts on a smooth level surface
when starting.
■ NEVER operate this unit indoors.
Operate this unit only in a well ven-
tilated area. Be aware of carbon
monoxide poisoning. Exhaust gases
and lubrication oil mist can cause
serious injury or death.
■ Stop the unit immediately if it
suddenly begins to vibrate or
shake. Inspect for broken, miss-
ing or improperly installed parts or
attachments.
■ Always make sure the Power-
Broom attachment is properly
installed and firmly tightened
before operation.
■ Never transport the unit nor set
it down with the engine running.
An engine that’s running could be
accidentally accelerated causing
the drum assemblies to rotate.
■ Always hold the machine firmly with
both hands when sweeping, and
maintain control at all times.
■ Always wear eye protection to
shield against thrown objects.
■ Always stop the engine immediately
and check for damage if you strike a ■ Always disconnect the spark plug
■ Never modify or disable any of the
foreign object or if the unit becomes
tangled. Do not operate with broken
or damaged equipment.
wire before performing any main-
tenance work.
unit’s safety devices.
■ Do not make unauthorized modifi-
■ Always maintain this unit accord-
ing to this owner’s manual and fol-
low the recommended scheduled
maintenance.
cations to this unit.
■ Always clear your work area of trash
or hidden debris to help ensure
good footing.
■ Make sure there are no missing or
loose fasteners, and that the igni-
tion switch and throttle controls
are working properly.
■ Always use genuine Shindaiwa
parts and accessories when repair-
ing or maintaining this unit.
■ Keep a Solid Stance. Maintain
footing and balance at all times.
Do not stand on slippery, uneven
or unstable surfaces. Do not work
in odd positions or on ladders. Do
not over reach.
■ Do not operate the unit with the
muffler removed.
Safety Labels
This label indicates the minimum distance between
front handle and rear grip per ANSI B175.3.
READ THE
OPERAT OR’S MANUAL.
HOT SURFACE
WEAR HEARING AND ANSI Z87.1
APPROVED EYE PROTECTION.
BEWARE OF THROWN
DIRT AND DEBRIS.
DO NOT USE ON UNGUARDED
ELEVATED SURFACES.
MAINTAIN A
SHALLOW
WORKING
ANGLE…
iMPORTanT!
…AVOID MOVING TOWARD
VERTICAL.
Safety and Operation Information Labels: Make sure
all information labels are undamaged and readable.
Immediately replace damaged or missing informa-
tion labels. New labels are available from your local
authorized Shindaiwa dealer.
Shindaiwa Inc.
80267
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety (continued)
The Properly Equipped Operator
Always protect yourself from hazards
such as thorny brush and flying debris
by wearing gloves and close fitting
clothing that covers arms and legs.
Never wear shorts. Don’t wear loose
clothing or items such as jewelry that
could get caught in machinery or
underbrush. Secure long hair so it is
above shoulder level.
Always wear eye and hearing protection.
Shindaiwa recommends wearing a face shield as
additional face and eye protection.
Always operate with both hands
firmly gripping the unit.
Keep a proper footing and do not
overreach—maintain your balance
at all times during operation.
Keep away from rotating
sweeper belts or bristles at
all times, and NEVER lift a
moving attachment above
waist-height.
Wear sturdy footwear with nonslip
soles to provide good footing. Steel-
toed safety boots are recommended.
Never operate unit bare-footed!
Be Aware of the Working Environment
ALWAYS clear your work area of trash or
hidden debris that could be thrown back at
you or toward a bystander. When operating
in rocky terrain or near electric wires or
fences, use extreme caution to avoid
Be careful when operating on a slope or on slippery
terrain, especially during rainy weather or when pulling
debris toward you.
contacting such items with the sweeper belts.
If the drum assemblies jam, switch the
engine OFF and inspect the drums,
axles and gearcase for damage.
Keep the unit as clean as
possible. Keep it free of
loose vegetation, mud,
etc.
Do not use this unit on
rooftops or elevated surfaces
Keep bystanders
at least 15 meters
away from the unit
while operating
to reduce the risk
of being struck by
thrown debris.
When transporting the unit in a
vehicle, tie it down securely to
prevent damage and fuel spillage.
Maintain a low working angle
and avoid steep angles of
operation. A steep working
angle risks loss of control of
the machine.
Never operate the PowerBroom around
objects that could tangle in the drums
and cause loss of control.
Transport the
machine with the
engine OFF.
Never allow the engine to run at
high RPM without a load. Doing
so could damage the engine.
Always keep the
handles clean.
Be constantly alert for objects and debris that could be
thrown either from the sweeper belts or bounced from a
hard surface.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Product description
Spark Plug
Using the illustration as a guide, famil-
iarize yourself with your machine and its
various components. Understanding your
machine helps ensure top performance,
long service life and safer operation.
PS344
Grip
Ignition Switch
Handle
Fuel Tank
Outer Tube
Tank
Protector
Sweeper Belt
Gearcase
Throttle
Trigger
Sweeper Drum
WARNING!
Do not make unauthorized
modifications or alterations to any of
these units or their components.
Specifications
Model
PS344
Dry Weight (less sweepers)
Engine Type
6.0 kg/13.2 lb.
4-cycle, vertical cylinder, air cooled
Bore x Stroke
Displacement
38 x 30 mm/1.5 x 1.2 in.
34 cc/2.1 cu. in.
Fuel/Oil Ratio
50:1 with *ISO-L-EGD or JASO FD class engine oil
Fuel Tank Capacity
Carburetor Type
Ignition
660 ml/22.4 oz.
Diaphragm-type
One-piece electronic, program controlled
NGK CMR5H
Spark Plug
Electrode Gap
0.6 mm/ .024 in.
Torque
16.7 - 18.6 N∙m / 148-165 in • lbf
Foam pre-filter; sealed felt main filter
Recoil
Air Cleaner Type
Starting Method
Stopping Method
Transmission Type
Gear Reduction Ratio
Engine Idle Speed
Clutch Engagement Speed
Wide Open Throttle Speed (W.O.T.)
Slide switch
Automatic, centrifugal clutch w/worm gear
40:1
3,000 RPM
4,200 RPM
10,500 RPM
*Specifications are subject to change without notice.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Emission Control (Exhaust & Evaporative)
EPA 2010 and Later and/or C.A.R.B. TIER III
The emission control system for the engine is EM/TWC (Engine Modification and 3-way Catalyst) and for the fuel tank
the Control System is EVAP (Evaporative Emissions) or N (for nylon tank). Evaporative emission may be applicable to
California models only.
An Emission Control Label is located on the unit. (This is an EXAMPLE ONLY; information on label varies by en-
gine FAMILY).
PRODUCT EMISSION DURABILITY (EMISSION COMPLIANCE PERIOD)
The 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine
emissions output meets applicable emissions regulations, provided that approved maintenance procedures are
followed as listed in the Maintenance Section of this manual.
assembly
Prior to assembly
Before assembling, make sure you have
■ Kit containing hardware, owner/
WARNING!
all the components required for a com-
plete unit:
operator's manual, tool kit for rou-
tine maintenance. Tool kits vary
by model and may inclue a hex
wrench, spanner, and a combina-
tion spark plug wrench/screwdriver.
Do not make unauthorized
modifications or alterations to your
machine or its components.
■ PowerBroomUnit
iMPORTanT!
■ Carefully inspect all components for
The terms “left”, “left-hand”, and
“LH”; “right”, “right-hand”, and “RH”;
“front” and “rear” refer to directions as
viewed by the operator during normal
operation.
damage before assembling.
Adjustable Handle
Handle
This unit comes with the handle
installed. It can be re-adjusted for
operator comfort in the following
manner.
Throttle Assembly
1. Loosen adjustment knob. Locate
the handle at the best position for
operator comfort (usually about
10 inches ahead of the throttle
lever), and secure it by tightening
the adjustment knob at the handle
base.
Mounting Screw
Washer
Adjustment Knob
Washer
Hex Nut
Outer Tube
6
Download from Www.Somanuals.com. All Manuals Search And Download.
assembly (continued)
Adjust Throttle Lever
Free Play
Loosen the air cleaner
cover knobs
The throttle lever free play should be
approximately 3/16-1/4 inch (4-6 mm).
Make sure that the throttle lever oper-
ates smoothly without binding. If it
becomes necessary to adjust the lever
free play, follow the procedures and
illustrations that follow.
Cable
Adjuster
1. Loosen the air cleaner cover knobs
and remove the air cleaner cover.
Lock Nut
2. Loosen the lock nut on the cable
adjuster.
3. Turn the cable adjuster in or out as
required to obtain proper free play
3/16-1/4 inch (4-6 mm).
4. Tighten the locknut.
3/16-1/4 inch (4-6 mm)
Throttle Free Play
5. Reinstall the air cleaner cover.
Sweeper Assembly (sold separately)
Secure the drum
axle to the shaft
2
Clevis
Pin
Hitch
Pin
Install drum
axle onto
output shaft
1
Drum
Axle
Cotter
Pin
4
Secure with a
cotter pin
Install the sweeper drum
assembly
3
Drum
Assembly
7
Download from Www.Somanuals.com. All Manuals Search And Download.
assembly (continued)
1. Push one of the drum axles onto
either of the two gearcase output
shafts. If necessary, rotate the drum
axle until the clevis pin hole in the
axle aligns with the matching hole
in the gearcase output shaft.
2. Use a clevis pin and hitch pin to
secure the drum axle to the shaft.
The PowerBroom tool should now be
completely assembled.
3. Slide the recessed end of a
sweeper drum assembly over the
installed axle, and then push the
drum down the axle until the cotter
pin hole in the axle extends above
the drum surface.
CaUTiOn!
4. Use a cotter pin to secure the drum
assembly on the axle (see inset).
The cotter pin is designed to fit
tightly against the outboard end of
the drum, so you may need to com-
press the drum face slightly during
installation. spead the ends of the
cotter pin to secure.
The two drum assemblies are
identical, but each drum must be
installed with its recessed end
facing toward the gearcase.
5. Repeat Steps 1-4 to install the
remaining axle and drum assembly.
Mixing Fuel
WARNING!
Alternative fuels, such as E15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting Shindaiwa
requirements are NOT approved for use in Shindaiwa gasoline engines. Use of alternative fuels may cause
performance problems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including,
but not limited to, improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel
lines, gaskets, carburetors and other engine components.
Fuel Requirements
Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain
up to 10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood
alcohol) is NOT approved.
Hybrid 4TM Mixture Oil - Engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. M345/FD standards must be
used. Shindaiwa highly recommends using Shindaiwa Red ArmorTM engine oil in all Shindaiwa Hybrid 4TM engines to
protect the engine from harmful carbon build up, maintain engine performance, and increase engine life. Shindaiwa
Red ArmorTM engine oil exceeds ISO-L-EGD and J.A.S.O. M345/FD performance requirements. Engine problems
due to inadequate lubrication caused by failure to use an ISO-L-EGD (ISO/CD 13738) and J.A.S.O. M345/FD certified
oil will void the engine warranty.
Examples of 50:1 mixing quantities
iMPORTanT!
Shindaiwa Red ArmorTM engine oil may be mixed at 50:1 ratio for application
in all Shindaiwa engines sold in the past, regardless of ratio specified in those
manuals.
iMPORTanT!
Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30)
days, ninety (90) days when a fuel stabilizer is added. Use of unmixed, improp-
erly mixed, or stale fuel, may cause hard starting, poor performance, or severe
engine damage and void the product warranty. Read and follow instructions in
the Long Term Storage section of this manual.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Handling Fuel
DANGER
Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury
may result.
• Use an approved fuel container.
• DO NOT smoke near fuel.
• DO NOT allow flames or sparks near fuel.
• Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.
• NEVER refuel a unit when the engine is HOT or RUNNING!
• DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground.
• DO NOT overfill fuel tank. Wipe up spills immediately.
• Securely tighten fuel tank cap and close fuel container after refueling.
• Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired.
• Move at least 3m (10 ft.) from refueling location before starting the engine.
Mixing Instructions
1. Fill an approved fuel container with half of the required
amount of gasoline.
2. Add the proper amount of engine oil to gasoline.
3. Close container and shake to mix oil with gasoline.
4. Add remaining gasoline, close fuel container, and
remix.
Storage - Fuel storage laws vary by locality. Contact
your local government for the laws affecting your area.
As a precaution, store fuel in an approved, airtight con-
tainer. Store in a well-ventilated, unoccupied building,
away from sparks and flames.
iMPORTanT!
iMPORTanT!
Spilled fuel is a leading cause of hydrocarbon emissions.
Some states may require the use of automatic fuel shut-
off containers to reduce fuel spillage.
Stored fuel may separate. ALWAYS shake fuel container
thoroughly before each use.
After use
■ DO NOT store a unit with fuel in its tank. Leaks can
occur. Return unused fuel to an approved fuel storage
container.
Filling the fuel tank
WARNING!
Minimize the Risk of Fire
■ ALWAYS store gasoline in a container approved for
■ NEVER smoke or light fires near the engine.
flammable liquids.
■ ALWAYS stop the engine and allow it to cool before
■ ALWAYS inspect the unit for fuel leaks before each
use. During each refill, check that no fuel leaks from
around the fuel cap and/or fuel tank.
refueling.
■ ALWAYS Wipe all spilled fuel and move at least 3
meters (10 feet) from the fueling point and source before
starting.
If fuel leaks are evident, stop using the unit immedi-
ately. Fuel leaks must be repaired before using the unit.
■ NEVER place flammable material close to the engine
■ ALWAYS move the unit at least 3 meters (10 feet)
away from a fuel storage area or other readily flam-
mable materials before starting
muffler.
■
NEVER operate the engine without the muffler and spark
arrester screen in place and in good working condition.
the engine.
■ FUEL IS HIGHLY FLAMMABLE.
1. Place the unit on a flat, level surface.
3. Remove the fuel cap, and fill the tank with clean, fresh
fuel.
2. Clear any dirt or other debris from around the fuel filler cap.
4. Reinstall the fuel filler cap and tighten firmly.
CAUTION!
5. Wipe away any spilled fuel before starting engine.
Slowly remove the fuel cap only after stopping the engine
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting the Engine
iMPORTanT
Engine ignition is controlled by a two position switch mounted on the throttle housing labeled, “I” for ON or START and “O” for OFF
or STOP.
WARNING!
The attachment will operate immediately when the engine starts and could result in possible serious injury. Keep mov-
able parts of the attachment away from objects that could become entangled or thrown, and surfaces that could cause
loss of control.
WARNING!
Never start the engine from
the operating position.
Return Tube
Throttle Lock
Primer Bulb
ON
1. Slide the ignition switch to the “ON”
position.
2. Set the throttle lever to the “fast
Fast Idle
Button
idle”:
a.Depress and hold the throttle lock,
then squeeze the throttle trigger.
Throttle
Trigger
b.Depress and hold the fast idle
button.
c. Release the throttle trigger and
throttle lock, then release fast idle
button.
3. Press the primer bulb until fuel
Hold
the unit
firmly...
can be seen flowing in the trans-
parent return tube.
4. Set the choke lever to the CLOSED
position if engine is cold.
iMPORTanT!
The primer system only pushes fuel
through the carburetor. Repeatedly
pressing the primer bulb will not flood
the engine with fuel.
5. While holding the outer tube firmly
...and pull recoil
starter handle
with left hand. Use your other hand
to slowly pull the recoil starter
Make sure the
attachment is clear
upward
Closed
of obstructions!
handle until resistance is felt, then
pull quickly to start the engine.
iMPORTanT!
If the engine fails to start after several
attempts with the choke in the closed
position, the engine may be flooded
with fuel. If flooding is suspected, refer
to the ”Starting a Flooded Engine”
section of this manual.
CaUTiOn!
Do not pull the recoil starter to
the end of the rope travel. Pulling
the recoil starter to the end of
the rope travel can damage the
starter.
6. When the engine starts, slowly
move the choke lever to the “OPEN”
position. (If the engine stops after
the initial start, close the choke and
restart.)
7. Operating the throttle will automati-
cally disengage the fast idle setting.
Open
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting the Engine (continued)
When the Engine Starts...
■ After the engine starts, allow the
engine to warm up at idle 2 or 3
minutes before operating the unit.
■
Advancing the throttle makes the
cutting attachment move faster;
releasing the throttle permits the
attachment to stop moving. If the
cutting attachment continues to
move when the engine returns to
idle, carburetor idle speed should
be adjusted (see “Adjusting Engine
Idle”.)
If the engine does not start
■ Repeat the appropriate starting pro-
cedure for a cold or warm engine.
■ If the engine does not continue to
run, repeat the appropriate crank-
ing procedures for a cold or warm
engine.When the engine starts,
clear excess fuel from the combus-
tion chamber by accelerating the
engine several times with the throt-
tle lever.
■ If the engine still fails to start,
use the procedures for “Starting a
flooded engine.”
Starting a flooded engine
WARNING!
Burn danger from hot engine!
1. Slide the ignition switch to the “I” (ON) position.
2. Open the choke, put the throttle lever in the full throttle position, then clear excess fuel from the combustion chamber by
cranking the engine several times.
3. If the engine still fails to start or fire, refer to the troubleshooting flow chart at the end of this manual.
Stopping the Engine
OFF
Idle the engine briefly before stopping
(about 2 minutes), then slide the igni-
tion switch to the “O” (Engine OFF)
position.
Checking Unit Condition
NEVER operate the unit with the pro-
tective devices (ignition switch, etc.)
removed!
NEVER use a cracked or warped Pow-
erBroom drum or axle: replace it with a
serviceable one.
NEVER allow the engine to run at high
RPM without a load. Doing so could
damage the engine.
ALWAYS make sure the PowerBroom
tool is properly installed and firmly
tightened before operation.
ALWAYS stop the engine immedi-
ately and check for damage if you
strike a foreign object or if the machine
becomes tangled. Do not operate with
broken or damaged equipment.
NEVER operate a machine with worn
or damaged fasteners or attachment
holders.
Use only authorized Shindaiwa parts
and accessories. Do not make modi-
fications to your machine without the
written approval of Shindaiwa.
ALWAYS make sure the attachment fits
properly into the appropriate attachment
holder. If a properly installed attachment
vibrates, replace the attachment with
new one and re-check.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
Break-in and Operation
Once broken in, a PowerBroom will
effortlessly move an amazing variety of
materials, ranging from snow or stand-
ing water to heavier objects such as
gravel or wood chips.
The PowerBroom works best when its
rubber fins can quickly slide or “skim”
over the surface being swept. New or
replacement sweeper belts tend to grip
or drag on hard surfaces, and should
be thoroughly broken in or “scuffed”
before the broom is actually put to
work.
WARNING!
BURN DANGER! The gear-
case will become very hot during
normal operation.
Experience will help you understand
the operating principles of the PowerB-
room, but safe operation must be prac-
ticed from the start.
WARNING!
KEEP CLEAR of drum
assemblies during starting opera-
tions! The drums may rotate during
startup.
Break-in is easily accomplished by
operating the PowerBroom at full throt-
tle for 3 to 5 minutes in loose gravel or
similar abrasive material.
Optional accessories
Debris shield
A plastic debris shield is available from
your Shindaiwa dealer as a useful
option to your PowerBroom. The shield
helps prevent broadcasting debris
when large volumes of material are
forced over the top of the drum during
operation.
Optional debris shield
Operating Techniques
Sweeping Windrows
WARNING!
Operate the PowerBroom at or near full
throttle with its sweeper fins resting on
the work surface.
Reversing the PowerBroom
will cause debris to be thrown back
toward the operator. When revers-
ing the PowerBroom, use lower
throttle settings and be aware that
thrown debris may also affect your
footing!
iMPORTanT!
It is both tiring and unnecessary to lift
or hold the fins from the work surface
during sweeping.
When sweeping narrow areas such
as sidewalks, the PowerBroom can be
used to throw material directly ahead of
the operator. Clearing wider areas may
require sweeping at an angle to create
windrows to one side of the path being
cleared.
For long-term inverted
operation…
Sweeping
corners with the
PowerBroom upside
down
Adjustment Knob
Windrows of lighter materials often
can be combined into one main row or
pile for eventual pickup, while heavy
or bulky material may need to be col-
lected row-by-row.
…loosen the adjustment
knob to reverse the
handle.
DIRECTION OF
ROTATION
To pull debris from corners, reverse
sweeper drum rotation by turning the
powerhead over (throttle facing “up”).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
iMPORTanT!
WARNING!
Air Filter
MAINTENANCE, REPLACEMENT OR
REPAIR OF EMISSION CONTROL
DEVICES AND SYSTEMS MAY BE
PERFORMED BY ANY REPAIR ESTAB-
LISHMENT OR INDIVIDUAL; HOW-
EVER, WARRANTY REPAIRS MUST
BE PERFORMED BY A DEALER OR
SERVICE CENTER AUTHORIZED
BY ECHO, INC. THE USE OF PARTS
THAT ARE NOT EQUIVALENT IN PER-
FORMANCE AND DURABILITY TO
AUTHORIZED PARTS MAY IMPAIR THE
EFFECTIVENESS OF THE EMISSION
CONTROL SYSTEM AND MAY HAVE
A BEARING ON THE OUTCOME OF A
WARRANTY CLAIM.
The H4 engine that powers your
Shindaiwa model is a hybrid 4-stroke
engine. As a hybrid, the engine is
lubricated by oil mixed with the gaso-
line and air from the carburetor that
moves through and around the inter-
nal parts of the engine in a similar way
that a 2-stroke engine is lubricated.
Without the heavy duty 2-stage air fil-
ter equipped on all H4 engines, dust
and dirt could also move through the
engine, decreasing engine life, increas-
ing valve wear and the need for more
frequent valve adjustments. To keep
your H4 engine strong and reliable,
Shindaiwa recommends that you check
and service the air filter as instructed in
the 10-Hour Maintenance section that
follows
Before performing any
maintenance, repair, or cleaning work
on the unit, make sure the engine and
cutting attachment are completely
stopped. Disconnect the spark plug
wire before performing service or
maintenance.
Muffler
This unit must never be operated with
a faulty or missing spark arrester or
muffler. Make sure the muffler is well
secured and in good condition. A worn
or damaged muffler is a fire hazard and
may also cause hearing loss.
Spark Plug
WARNING!
Keep the spark plug and wire connec-
tions tight and clean.
Non-standard accessories,
cutting attachment, or replacement
parts may not operate properly with
your unit and may cause damage
and lead to personal injury.
Fasteners
Make sure nuts, bolts, and screws
(except carburetor adjusting screws)
are tight.
Daily Maintenance
Prior to each work day, perform the
following:
■
Carefully remove any accumula-
tions of dirt or debris from the muf-
fler and fuel tank. Check cooling
air intake area at base of crankcase.
Remove all debris. Dirt build-up
in these areas can lead to engine
overheating, fire, or premature wear.
■ Check for loose or missing screws
or components. Make sure the
attachment is securely fastened.
■ Remove all dirt and debris from the
engine, check the cooling fins and
air cleaner for clogging, and clean
as necessary.
■ Make sure nuts, bolts, and screws
(except carburetor idle speed
adjusting screws) are tight.
■ Check the entire unit for leaking fuel
■ Clean any debris or dirt from the
or grease.
sweeper attachment.
10-Hour Maintenance
(more frequently in dusty
conditions)
Unscrew
fasteners
1. Remove the air cleaner cover by
loosening the thumbscrews and
lifting.
Pre-filter
2. Remove and inspect the pre-filter.
If the pre-filter is torn or otherwise
damaged, replace it with a new one.
Air filter
element
3. Clean the pre-filter with soap and
water. Let dry before reinstalling.
4. Inspect the air filter element. If the
element is damaged or distorted,
replace it with a new one.
iMPORTanT!
Direct the air stream at the inside face
of the filter only!
5. Tap filter gently on a hard surface to
dislodge debris from element or use
compressed air from the inside to
blow debris out and away from the
air filter element.
CaUTiOn!
Never operate the unit if the air
cleaner assembly is damaged or
missing!
6. Install the air filter element, pre-filter
and cover in the reverse order of
removal.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance (continued)
10/15-Hour Maintenance
Remove and clean or replace the
spark plug.
■ Adjust the spark plug electrode gap
to 0.024 inch (0.6 mm). If the spark
plug must be replaced, use only an
NGK CMR5H or equivalent resistor
type spark plug of the correct heat
range.
0.024 inch
(0.6 mm)
CaUTiOn!
Before removing the spark plug,
clean the area around the plug to
prevent dirt and debris from getting
into the engine’s internal parts.
Clean the spark plug
and check the gap at
the electrode.
nOTE:
The NGK CMR5H also meets the
requirements for electro magnetic com-
pliance (EMC).
50-Hour Maintenance
Remove and replace the fuel filter
element.
■ Use a hooked wire to extract the
fuel filter from inside the fuel tank.
Inspect the fuel filter element. If it
shows signs of contamination from
debris, replace it with a genuine
Shindaiwa replacement fuel filter
element.
Hooked wire
Fuel filter element
CaUTiOn!
Fuel filter maintenance
Make sure you do not pierce the fuel
line with the end of the hooked wire.
The line is delicate and can be dam-
aged easily.
Before reinstalling the filter, inspect
the fuel line. If you discover dam-
age or deterioration, the unit should
be removed from service unitl it
can be inspected by a Shindaiwa-
trained service technician.
135 hour maintenance
■ Replace the spark plug annually.
See the section “10 -15 Hour Main-
tenance” for instructions.
■ Combustion chamber should be
decarbonized, and the valve clear-
ance should be adjusted. It is highly
recommended that this is done
by a Shindaiwa-trained service
technician.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance (continued)
135 hour maintenance (cont.)
Valve Adjustment
1. Remove cylinder cover, rocker arm
cover, and spark plug. Rotate the
crankshaft while observing the piston
through the spark plug opening.
When the piston is at the top of the
compression stroke (TDC), the valves
can be adjusted.
CaUTiOn!
■ Performing a valve adjustment
incorrectly may cause hard
starting and/or can damage the
engine.
2. Loosen adjuster locknut so that the
2.5 mm Allen socket head adjustment
screw can turn freely.
6. Turn engine over several times,
and return to TDC-compression.
Recheck with proper feeler gauge to
make sure clearance adjustment did
not change as a result of tightening
the locknut. Readjust as necessary.
3. Insert 0.10 mm (0.004”) feeler gauge
between valve stem tip and rocker
arm.
■ If you are unfamiliar with this
engine or uncomfortable with
this procedure, consult with an
authorized Shindaiwa servicing
dealer.
7. Replace rocker arm cover gasket
to assure proper sealing and install
cover.
4. Turn adjustment screw (clockwise =
tighter, counter-clockwise = looser)
until feeler gauge is almost snug.
Back off just enough to allow gauge
to slip out with limited resistance.
iMPORTanT!
If a new gasket is not available and/
or the old gasket is not damaged, the
old gasket may be reused. Never use
cracked or damaged gaskets!
5. While holding the adjustment screw
in place with the Allen driver, tighten
the locknut with a wrench.
300-hour maintenance
Gearcase Lubrication
The gearcase should be filled with 60 cc
(2.0 fl.oz.) of Mobil SHC634 Synthetic
Gear Oil. A maximum of 75-80 cc can be
used, but never to exceed 80 cc. Opera-
tion with excessive oil level will result
in high operating temperatures. Do not
overfill!
Fill the gearcase to the bottom of the
chamfer on the output gear.
DO NOT OVERFILL!
WARNING!
Turn gearcase side plate to break the seal
and lift the plate from the gearcase
BURN DANGER! The
gearcase will be extremely hot after
use!
nOTE:
6. Inspect the sideplate for damage and
clean off all remaining liquid gasket
material with brake cleaner or ace-
tone. Coat the outer sealing flange of
the sideplate with silicon sealant.
It may be necessary to use a heat gun
to soften the sealer material.
Replacing the gearcase oil
1. Disconnect spark plug wire at
engine.
4. Turn the gearcase to the LH side
and and allow all used gearcase oil
to drain into a small container.
7. Replace the cover and install the
four sideplate screws. Tighten
securely.
2. Remove the LH Drum and axle
assembly (as viewed from the operat-
ing position). Wipe the sideplate
clean and remove four screws (it
is not necessary to remove the
gearcase from the outer tube).
5. Place the gearcase on the RH side
and supported so the outer tube
is parallel to the ground. Refill the
gearcase with 60 cc (2.0 fl.oz) of
Mobil SHC634 Synthetic Gear Oil
to the bottom of the chamfer on
the output gear. The correct oil
depth is 5/8" (15.5 mm). DO NOT
OVERFILL!
8. Reinstall the drum and axle assem-
bly. Refer to the section “Assembly:
Sweeper Assembly” for instructions.
3. Turn gearcase side plate to break
the seal and lift the plate from the
gearcase.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance (continued)
Muffler Maintenance
If the engine becomes sluggish and low
on power, check and clean the spark
arrester screen.
Engine Cover
WARNING!
Engine
Cover
Screws
Never operate the unit
with a damaged or missing muffler
or spark arrester! Operating with a
missing or damaged spark arrester
is a fire hazard and could also dam-
age your hearing.
1. With a 3 mm hex wrench remove
the 3 engine cover screws and the
engine cover.
Muffler
Muffler Gasket
2. With a 4 mm hex wrench, remove
the 3 muffler bolts and the muffler.
3. With a small flat bladed screwdriver
remove the 2 screws holding the
spark arrester screen and cover to
the muffler.
Muffler Bolts
4. Remove the screen and clean it
with a stiff bristle brush.
Spark Arrester Screen
Spark Arrester Cover
5. Inspect the cylinder exhaust port for
any carbon buildup.
6. Reassemble the spark arrester,
muffler and engine cover in the
reverse order of disassembly.
Cover Screws
iMPORTanT!
If you note excessive carbon buildup,
consult with an authorized Shindaiwa
servicing dealer.
Carburetor adjustment
Engine Break-In
New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be
made. During the break-in period your engine performance will increase and exhaust emissions will stabilize. Idle speed can
be adjusted as required.
High Altitude Operation
This engine has been factory adjusted to maintain satisfactory starting, emission, and durability performance up to
1,100 feet above sea level (ASL) (96.0 kPa). To maintain proper engine operation and emission compliance above
1,100 feet ASL the carburetor may need to be adjusted by an authorized Shindaiwa service dealer.
iMPORTanT!!
If the engine is adjusted for operation above 1,100 feet ASL, the carburetor must be re-adjusted when operating the
engine below 1,100 feet ASL, otherwise severe engine damage may result.
nOTE:
Every unit is run at the factory and the carburetor is set in compliance with emission regulations. Carburetor adjustments,
other than idle speed, must be performed by an authorized Shindaiwa dealer.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
adjusting Engine idle
The engine must return to idle speed
whenever the throttle lever is released.
Idle speed is adjustable, and must be
set low enough to permit the engine
clutch to disengage the attachment.
Idle Speed Adjustment
1. Place the trimmer on the ground,
then start the engine, and then
allow it to idle 2-3 minutes until
warm.
2. If the attachment rotates when the
engine is at idle, reduce the idle
speed by turning the idle adjusting
screw counter-clockwise.
WARNING!
The attachment must
NEVER rotate at engine idle! If
the idle speed cannot be adjusted
by the procedure described
here, return the trimmer to your
Shindaiwa dealer for inspection.
3. If a tachometer is available, adjust
idle. Check Specifications page for
correct idle speed.
4. Carburetor fuel mixture adjustments
are preset at factory and cannot be
serviced in the field.
Idle Adjusting
Screw
Long Term Storage
Whenever the unit will not be used for
30 days or longer, use the following
procedures to prepare it for storage:
■ Remove the spark plug and pour
about 1/4 oz. of engine oil into the
cylinder through the spark plug hole.
Slowly pull the recoil starter 2 or
3 times so oil will evenly coat the
interior of the engine. Reinstall the
spark plug.
CaUTiOn!
Gasoline stored in the carbure-
tor for extended periods can cause
hard starting, and could also lead to
increased service and maintenance
costs.
■ Clean external parts thoroughly
and apply a light coating of oil to all
metal surfaces.
■ Drain all the fuel from the carburetor
and the fuel tank.
iMPORTanT!
■ Before storing the unit, repair or
replace any worn or damaged parts.
To do so:
All stored fuels should be stabi-
lized with a fuel stabilizer such as
STA-BIL™.
■ Remove the air cleaner element
from the carburetor and clean it thor-
oughly with soap and water. Let dry
and reassemble the element.
1. Prime the primer bulb until no more
fuel is passing through.
2. Start and run the engine until it
stops running.
nOTE
■ Store the unit in a clean, dust-free
Damage resulting from stale or con-
taminated fuel is not covered by the
Shindaiwa warranty policy.
3. Repeat steps 1 and 2 until the
engine will no longer start.
area.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
EnGinE dOES nOT STaRT OR haRd TO STaRT
Remedy
Let cool completely and restart.
Possible Cause
Engine hot/heat soaked.
Low fuel quality.
What To Check
Vaporlock.
Refill with fresh, clean unleaded gasoline with a pump octane
of 89 or higher mixed with an air cooled engine oil that
meets or exceeds ISO-L-EGD and/or JASO FD classified oils
at 50:1 gasoline/oil ratio.
Valve adjustment.
Consult with an authorized Shindaiwa
servicing dealer. Adjust valves.
Valve clearance too tight.
Valve clearance too loose.
EnGinE dOES nOT STaRT
What To Check
Possible Cause
Remedy
Consult with an authorized Shindaiwa servicing dealer.
Faulty recoil starter.
Fluid in the crankcase.
Internal damage.
NO
NO
Does the engine crank?
YES
Tighten and re-test.
Loose spark plug.
Good compression?
Consult with an authorized Shindaiwa
servicing dealer.
Excess wear on cylinder,
piston, rings.
YES
Refill with fresh, clean unleaded gasoline with a pump octane
of 89 or higher mixed with an air cooled engine oil that
meets or exceeds ISO-L-EGD and/or JASO FD classified oils
at 50:1 gasoline/oil ratio.
Fuel incorrect, stale, or
contaminated; mixture incorrect.
NO
Does the tank contain fresh
fuel of the proper grade?
YES
Replace fuel filter or vent as required.
Re-start.
Check for clogged fuel filter
and/or vent.
Is fuel visible and moving
in the return line when
priming?
NO
NO
Consult with an authorized Shindaiwa
servicing dealer.
Priming pump not functioning properly.
YES
Move switch to “I” (ON) position
and re-start.
The ignition switch is in
“O” (OFF) position.
Is there spark at the spark
plug wire terminal?
Consult with an authorized Shindaiwa
servicing dealer.
Shorted ignition ground.
Faulty ignition unit.
YES
See "Starting a Flooded Engine"
If the plug is wet, excess
fuel may be in the cylinder.
Check the spark plug.
Clean and gap the spark plug. Check the Specifications
section for the correct plug and gap for your unit. Restart.
The plug is fouled or improperly
gapped.
Replace the spark plug. Check the Specifications section for
the correct plug and gap for your unit. Restart.
The plug is damaged internally
or of the wrong size.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide (continued)
LOw POwER OUTPUT
Remedy
What To Check
Possible Cause
Operator is overworking the unit.
Use a lower throttle setting.
Is the engine overheating?
Carburetor mixture is too lean.
Improper fuel ratio.
Consult with an authorized Shindaiwa
servicing dealer.
Refill with fresh, clean unleaded gasoline with a pump octane
of 89 or higher mixed with an air cooled engine oil that meets
or exceeds ISO-L-EGD and/or JASO FD classified oils at 50:1
gasoline/oil ratio.
Fan, fan cover, cylinder fins dirty
or damaged.
Clean, repair or replace as necessary.
Carbon deposits on the piston or
in the muffler.
Consult with an authorized Shindaiwa
servicing dealer.
Clogged air cleaner element.
Loose or damaged spark plug.
Service the air cleaner element.
Tighten or replace the spark plug.
Check the Specifications section for the correct plug and gap
for your unit.
Engine is rough at all
speeds. May also have
black smoke and/or
unburned fuel at the
exhaust.
Air leakage or clogged fuel line.
Water in the fuel.
Repair or replace fuel filter and/or
fuel line.
Refill with fresh, clean unleaded gasoline with a pump octane
of 89 or higher mixed with an air cooled engine oil that meets
or exceeds ISO-L-EGD and/or JASO FD classified oils at 50:1
gasoline/oil ratio.
Piston seizure.
Consult with an authorized Shindaiwa servicing dealer.
Faulty carburetor and/or diaphragm.
Overheating condition.
Improper fuel.
Consult with an authorized Shindaiwa
servicing dealer.
Engine is knocking.
Refill with fresh, clean unleaded gasoline with a pump octane
of 89 or higher mixed with an air cooled engine oil that meets
or exceeds ISO-L-EGD and/or JASO FD classified oils at 50:1
gasoline/oil ratio.
Carbon deposits in the
combustion chamber.
Consult with an authorized Shindaiwa
servicing dealer.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide (continued)
addiTiOnaL PROBLEMS
Possible Cause
Clogged air filter.
Remedy
Clean the air filter.
Symptom
Poor acceleration.
Clogged fuel filter.
Lean fuel/air mixture.
Replace the fuel filter.
Consult with an authorized Shindaiwa
servicing dealer.
Idle speed set too low.
Adjust idle. Check Specifications page for correct idle speed.
Ignition switch turned off.
Fuel tank empty.
Reset the switch and re-start.
Engine stops abruptly.
Refill with fresh, clean unleaded gasoline with a pump octane
of 89 or higher mixed with an air cooled engine oil that
meets or exceeds ISO-L-EGD and/or JASO FD classified oils
at 50:1 gasoline/oil ratio.
Water in the fuel.
Clogged fuel filter.
Replace fuel filter.
Shorted spark plug or loose terminal.
Clean or replace spark plug. Check the Specifications section
for the correct plug and gap for your unit. Tighten
the terminal.
Ignition failure.
Piston seizure.
Replace the ignition unit.
Consult with an authorized Shindaiwa
servicing dealer.
Ground (stop) wire is disconnected,
or switch is defective.
Test and replace as required.
Engine difficult to shut off.
Overheating due to incorrect spark plug.
Replace the spark plug. Check the Specifications section for
the correct plug and gap for your unit. Restart.
Overheated engine.
Idle engine until cool.
Consult with an authorized Shindaiwa
servicing dealer.
Top of engine is getting
dirty and oily.
Valve cover is leaking.
Adjust idle. Check Specifications page for correct
idle speed.
Consult with an authorized Shindaiwa servicing
dealer.
Idle set too high.
Engine will not idle
down.
Engine has an air leak.
Adjust idle. Check Specifications page for correct idle
speed.
Engine idle too high.
Attachment moves at
engine idle.
Broken clutch spring or worn clutch
spring boss.
Replace spring/shoes as required, check idle speed.
Loose attachment holder.
Inspect and re-tighten holders securely.
Warped or damaged attachment.
Inspect and replace attachment as
required.
Excessive vibration.
Loose gearcase.
Tighten gearcase securely.
Bent main shaft/worn or damaged bushings.
Inspect and replace as necessary.
Inspect and reinstall as required.
Shaft not installed in powerhead or gearcase.
Broken shaft.
Consult with an authorized Shindaiwa servicing
dealer.
Attachment will not move.
Damaged gearcase.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
SHINDAIWA LIMITED WARRANTY STATEMENT FOR
PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010
ECHO, INC'S RESPONSIBILITY
ECHO Incorporated’s (ECHO, INC.) Limited Warranty, provides to the original purchaser that this Shindaiwa product is free from defects
in material and workmanship. Under normal use and maintenance from date of purchase, ECHO, INC. agrees to repair or replace at it’s
discretion, any defective product free of charge at any authorized Shindaiwa servicing dealer within listed below application time periods,
limitations and exclusions. THIS LIMITED WARRANTY IS ONLYAPPLICABLE TO SHINDAIWA PRODUCTS SOLD BYAUTHORIZED
SHINDAIWADEALERS. IT IS EXTENDED TO THE ORIGINAL PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT
OWNERS EXCEPT FOR EMISSION RELATED PARTS. Repair parts and accessories replaced under this warranty are warranted only
for the balance of the original unit or accessory warranty period. Any damage caused by improper installation or improper maintenance
is not covered by this warranty. All parts or products replaced under warranty become the property of ECHO, INC. This warranty is
separate from the Emission control warranty statement supplied with your new product. Please consult the Emission Control Warranty
Statement for details regarding emission related parts. For a list of Authorized Shindaiwa Dealers refer to WWW.SHINDAIWA.COM or
call 1-877-986-7783.
OWNER’S RESPONSIBILITY
To ensure trouble free warranty coverage it is important that you register your Shindaiwa equipment on-line at WWW.SHINDAIWA.
COM or by filling out the warranty registration card supplied with your unit. Registering your product confirms your warranty coverage
and provides a direct link if we find it necessary to contact you.
The owner shall demonstrate reasonable care and use, and follow preventative maintenance, storage, fuel and oil usage as prescribed in
the operator’s manual. Should a product difficulty occur, you must, at your expense, deliver or ship your Shindaiwa unit to an authorized
Shindaiwa servicing dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit
after the repairs have been made. For your nearest authorized Shindaiwa servicing dealer, call Shindaiwa’s Dealer Referral Center, at
1-877-986-7783 or you can locate a Shindaiwa servicing dealer at WWW.SHINDAIWA.COM. Should you require assistance or have
questions concerning Shindaiwa’s Warranty Statement, you can contact our Consumer Product Support Department at 1-800-673-1558
or contact us through the web at WWW.SHINDAIWA.COM.
PRODUCT WARRANTY PERIOD
RESIDENTIAL APPLICATION
• 2 YEAR WARRANTY - Units for residential, or non-income producing use will be covered by this limited warranty for two (2) years
from date of purchase.
EXCEPTIONS:
• For engine powered products, the electronic ignition module, flexible drive cable, and solid drive shaft are warranted for the
life* of the product on parts only.
• Cutting attachments such as, but not limited to, bars, chains, sprockets, tines, blades, Power BroomTM, belts, and nylon trimmer
heads for residential or non-income producing use will be covered for failures due to defects in material or workmanship for a
period of 60 days from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not
covered by this warranty.
• Multipurpose Tool Attachments carry the same warranty duration as the units they are designed to fit.
COMMERCIAL APPLICATION
•
90 DAY WARRANTY - All Chain Saws and Cut-Off Saws for commercial, institutional, agricultural, industrial, or income producing use will be
covered by this limited warranty for 90 Days from the date of purchase.
• 2 YEAR WARRANTY - Units for commercial, institutional, agricultural, industrial, or income producing use will be covered by this
limited warranty for two (2) years from the date of purchase.
EXCEPTIONS:
• For engine powered products, the electronic ignition module, flexible drive cables, and solid drive shafts are warranted for the
life* of the product on parts only.
• Cutting attachments such as, but not limited to, bars, chains, sprockets, tines, blades, Power BroomTM, belts, and nylon trimmer
heads for commercial, institutional, agricultural, industrial, rental, or income producing will be covered for failures due to defects
in material or workmanship for a period of 30 days from original product purchase date. Any misuse from contact with concrete,
rocks, or other structures is not covered by this warranty.
• Multipurpose Tool Attachments carry the same warranty duration as the units they are designed to fit.
RENTAL APPLICATION - 90 DAYS WARRANTY
•
Units for rental use will be covered against defects in material and workmanship for a period of 90 days from the date of
purchase.
* ECHO INC’s liability under the “Lifetime” coverage is limited to furnishing parts specified under the PRODUCT WARRANTy PERIOD
section of this warranty statement for “Life” free of charge for a period of ten (10) years after the date of the complete unit’s final
production.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
PURCHASED REPAIR PARTS AND ACCESSORIES
• 90-day all applications
ATTENTION ENGINE POWERED PRODUCT OWNERS
This Shindaiwa engine powered product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior
performance. To help ensure the performance of the unit, it is required to use engine oil which meets the ISO-L-EGD Standard per
ISO/CD 13738 and JASO M345/FD Standards. Shindaiwa Red ArmorTM and Shindaiwa OneTM are a premium engine oil specifically
formulated to meet ISO-L-EGD (ISO/CD 13738) and JASO M345/FD Standards. The use of engine oils designed for other applications,
such as for outboard motors or lawnmowers can result in severe engine damage, and will void your engine limited warranty.
THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY:
•
Lack of lubrication or engine failure, due to the use of engine oils that do not meet the ISO-L-EGD (ISO/CD 13738) and JASO
M345/FD Standards. Shindaiwa ONETM Engine Oil meets the ISO-L-EGD and JASO M345/FD Standard. Emission related parts
are covered for 2 years regardless of engine oil used, per the statement listed in the EPA or California Emission Control Warranty
Explanation.
•
Damage caused by use of gasohol, containing methanol (wood alcohol), or gasoline containing less than 89 octane. Only use
gasoline which contains 89 octane or higher. Gasohol which contains a maximum 10% ethanol (grain alcohol) or 15% MTBE (methyl/
tertiary/butyl/ether) is also approved. The prescribed mixing ratio of gasoline to oil is listed on the Shindaiwa oil label and covered
in your operator’s manual.
•
•
Engine damage caused by use of ether or any starting fluids.
Damage caused by tampering with engine speed governor or emission components, or running engines above specified and
recommended engine speeds as listed in your operator’s manual.
•
•
•
Operation of the unit with improperly maintained/removed cutting shield or removed/damaged air filter.
Damage caused by dirt, pressure or steam cleaning the unit, salt water, corrosion, rust, varnish, abrasives, and moisture.
Defects, malfunctions or failures resulting from abuse, misuse, neglect, modifications, alterations, normal wear, improper servicing,
or use of unauthorized attachments.
•
•
Incorrect storage procedures, stale fuel, including failure to provide or perform required maintenance services as prescribed in the
operator's manual. Preventative maintenance as outlined in the operators manual is the customer’s responsibility.
Failures due to improper set-up, pre-delivery service or repair service by anyone other than authorized Shindaiwa servicing dealer
during the warranty period.
•
•
Certain parts and other items are not warranted, including but not limited to: lubricants, starter cords, and engine tune-ups.
Use of spark plugs other than those meeting performance and durability requirements of the OEM spark plug listed in the Operator's
Manuals.
•
Overheating or carbon scoring failures due to restricted, clogged exhaust port or combustion chamber, including damage to spark
arrester screen.
•
•
Adjustments after the first (30) thirty days and beyond, such as carburetor adjustment and throttle cable adjustment.
Damage to gears or gear cases caused by contaminated grease or oil, use of incorrect type or viscosity of lubricants, and/or failure
to comply with recommended grease or oil change intervals.
•
•
Damage caused by pump or sprayer running dry, pumping or spraying caustic or flammable materials, or lack of or broken
strainers.
Additional damage to parts or components due to continued use after operational problem or failure occurs. Should operational
problem or failure occur, the product should not be used, but delivered as is to an authorized Shindaiwa servicing dealer.
It is a dealer’s and/or customer’s responsibility to complete and return the warranty registration card supplied with your Shindaiwa
product or by visiting WWW.SHINDAIWA.COM. your receipt of purchase including date, model and serial number must be maintained
and presented to an authorized Shindaiwa servicing dealer for warranty service. Proof of purchase rests solely with the customer. Some
states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. Some states do not
allow the exclusion or limitation of incidental or consequential damages, so you may also have other specific legal rights which vary from
state to state. This limited warranty is given by ECHO Incorporated, 400 Oakwood Rd., Lake Zurich, IL 60047.
DISCLAIMER OF IMPLIED WARRANTIES
This limited warranty is in lieu of all other expressed or implied warranties, including any warranty of FITNESS FOR A PARTICULAR
PURPOSE OR USE and any implied warranty of MERCHANTABILITY otherwise applicable to this product. ECHO, INC. and its affiliated
companies shall not be liable for any special incidental or consequential damage, including lost profits. There are no warranties extended
other than as provided herein. This limited warranty may be modified only by ECHO, INC.
99922201031
02/05/2010
22
Download from Www.Somanuals.com. All Manuals Search And Download.
ECHO INCORPORATED EMISSION CONTROL WARRANTY STATEMENT
FOR ECHO AND SHINDAIWA BRANDS
The Environmental ProtectionAgency (EPA) and the CaliforniaAir Resources Board (C.A.R.B.) and ECHO Incorporated (ECHO Inc.) are pleased
to explain the emission control system warranty on your 2010 and later equipment/small off-road engine (SORE). New equipment/SORE must be
designed, built and equipped to meet stringent EPA and C.A.R.B. anti-smog standards. ECHO Inc. must warrant the emission control system on
your equipment/SORE for the periods of time listed below, provided there has been no abuse, neglect or improper maintenance of your equipment/
SORE. Your emission control system may include parts such as: carburetor, fuel-injection system, ignition system, catalytic converter/muffler, fuel
tank, fuel feed lines, fuel cap assembly, spark plug, air filters, and other associated components. Where a warrantable condition exists, ECHO
Inc will repair your equipment/SORE at no cost to you including diagnosis, parts and labor. The Emission Control System warranty is extended
to the original owner including all subsequent owners.
MANUFACTURER'S WARRANTY COVERAGE:
The emission control system is warranted for 2 years or the length of the ECHO Inc. warranty, whichever is longer. If any emission-related part
on your equipment is defective, the part will be repaired or replaced by ECHO Inc. or its Authorized Service Representative.
OWNER'S WARRANTY RESPONSIBILITIES:
As the equipment/SORE owner, you are responsible for the performance of the required maintenance listed in your Operator's Manual. ECHO
Inc. recommends that you retain all receipts covering maintenance on your equipment/SORE however, ECHO Inc. cannot deny warranty solely
for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the equipment/SORE owner, you should be
aware that ECHO Inc. may deny you warranty coverage if your equipment/SORE or a part has failed due to abuse, neglect, improper maintenance
or unapproved modifications.
You are responsible for presenting your equipment/SORE to an ECHO Inc. authorized service representative as soon as a problem exists. The
warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If a warrantable condition exists and there is no
Authorized Dealer within 100 miles, ECHO Inc. will pay to ship the unit to the nearest authorized dealer. If you have questions regarding your
warranty coverage, you should contact ECHO Inc. at 1-800-673-1558, web site WWW.ECHO-USA.COM or contact Shindaiwa at 1-877-986-
7783, web site WWW.SHINDAIWA.COM.
WHAT DOES THIS WARRANTY COVER?
ECHO Inc. warrants that your equipment/SORE was designed, built and equipped to conform with applicable EPA and C.A.R.B. emissions
standards and that your equipment/SORE is free from defects in material and workmanship that would cause it to fail to conform with applicable
requirements for 2 years or the length of the ECHO Inc. warranty, whichever is longer. The warranty period begins on the date the product is
purchased by an end user.
HOW WILL A COVERED PART BE CORRECTED?
If there is a defect in a part covered by this warranty, any ECHO Inc. Authorized Service Dealer will correct the defect. You will not have to pay
anything to have the part adjusted, repaired or replaced. This includes any labor and diagnosis for warranted repairs performed by the dealer. In
addition, engine parts not expressly covered under this warranty but whose failure is a result of a failure of a covered part will be warranted.
WHAT PARTS ARE COVERED?
Any applicable emission related part not scheduled for "required maintenance" will be repaired or replaced within the warranty period. The repaired
or replaced part will be warranted for the remaining ECHO Inc. warranty period.
Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the warranty period stated
above. Any such part repaired or replaced under warranty will be warranted for the remaining ECHO Inc. warranty period.
Any emission related part scheduled for replacement during "required maintenance" is warranted for the period of time prior to the first scheduled
replacement point for that part. Any such part repaired or replaced under warranty shall be warranted for the remainder of the period prior to the
first scheduled replacement point for that part.
Any manufacturer-approved replacement part may be used in the performance of any warranty maintenance or repairs on emission related parts,
and must be provided without charge if the part is still under warranty.
Any replacement part that is equivalent in performance and durability may be used in non-warranty maintenance or repairs, and shall not reduce
the warranty obligations of the manufacturer.
Throughout the equipment/SORE warranty period, ECHO Inc. will maintain a supply of warranted parts sufficient to meet the expected demand
for such parts.
SPECIFIC EMISSION RELATED WARRANTED PARTS:
• Electronic Ignition System
• Catalytic Converter / Muffler Assembly
• Choke
• Spark Plug
• Carburetor (complete assembly or replaceable components)
• Fuel-Injection Assembly (or replaceable components)
• Fuel Cap Assembly
• Fuel Tank
• Air Filter
• Fuel Feed Line (and associated clamps/connectors as applicable)
WHAT IS NOT COVERED?
Any failure caused by abuse, neglect, improper maintenance, unapproved modifications, use of unapproved add-on parts/modified parts or
unapproved accessories.
99922201033
01/2010
This Emission Control Warranty is valid only for the U.S.A., it's Territories, and Canada.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
nOTES
24
Download from Www.Somanuals.com. All Manuals Search And Download.
nOTES
25
Download from Www.Somanuals.com. All Manuals Search And Download.
nOTES
26
Download from Www.Somanuals.com. All Manuals Search And Download.
nOTES
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Servicing information
Parts/Serial number
Genuine Shindaiwa Parts and Assemblies for your Shindaiwa products are available only from an Authorized
Shindaiwa Dealer. When you do need to buy parts always have the Model Number, Type and Serial Number of the
unit with you. You can find these numbers on the engine. For future reference, write them in the space provided
below.
MODEL_______________________
SERIAL NUMBER______________________________________
Service
Service of this product during the warranty period must be performed by an Authorized Shindaiwa Service Dealer.
For the name and address of the Authorized Shindaiwa Service Dealer nearest you, ask your retailer or call: 1-877-
986-7783. Dealer information is also available on WWW.SHINDAIWA.COM. When presenting your unit for Warranty
service/repairs, proof of purchase is required.
Consumer Product Support
If you require assistance or have questions concerning the application, operation or maintenance of this product you
may call the Shindaiwa Consumer Product Support Department at 1-877-986-7783 from 8:30 am to 4:30 pm (Central
Standard Time) Monday through Friday. Before calling, please know the model and serial number of your unit.
warranty Registration
To ensure trouble free warranty coverage it is important that you register your Shindaiwa equipment by filling out the
warranty registration card supplied with your unit. Registering your product confirms your warranty coverage and pro-
vides a direct link if we find it necessary to contact you.
additional or Replacement Manuals
Replacement Operator and Parts Catalogs are available from your Shindaiwa dealer or at WWW.SHINDAIWA.
COM or by contacting the Consumer Product Support Department (1-877-986-7783). Always check WWW.SHINDAI-
WA.COM for updated information.
ECHO Incorporated.
Yamabiko Corporation
400 Oakwood Road
7-2 Suehirocho 1-Chome, Ohme,
Lake Zurich, IL 60047-1564 U.S.A.
Tokyo, 198-8760, Japan
Phone: 81-428-32-6118
Fax: 81-428-32-6145
Telephone: 1-877-986-7783
Fax: 1-847-540-8416
T15411001001/T15411999999
T15312001001/T15312999999
Copyright© 2010 By Echo, Incorporated
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|