SHINDAIWA OWNER’S/0PERATOR'S MANUAL
EB501 BLOWER
High Performance
WARNING!
Minimize the risk of injury to yourself and others!
Read this manual and familiarize yourself with the con-
tents. Always wear eye and hearing protection when
operating this unit. Minimize the risk of injury: Read this
manual and familiarize yourself with its contents.
Part Number 68232-94011 Rev. 11/06
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTENTION STATEMENTS
This manual contains special “attention
statements” surrounded by boxes and
preceded by the triangular Attention
Symbol.
Read and follow this manual.
Failure to do so could result
in serious injury.
Wear eye and hearing
protection at all times during
the operation of this machine.
WARNING!
Do not operate this machine if
you are tired, ill or under the
influence of alcohol, drugs,
or medicine.
A statement preceded by the word
“WARNING” contains information
that should be acted upon to pre-
vent serious bodily injury.
IMPORTANT!
The operational procedures described
in this manual are intended to help
you get the most from your machine
and also to protect you and others
from harm. These procedures are
general guidelines only, and are not
intended to replace any safety rules/
laws that may be in force in your area.
If you have any questions regarding
your EB501 blower, or if you do not
understand something in this manual,
your Shindaiwa dealer will be glad to
assist you.
CAUTION!
A statement preceded by the word
“CAUTION” contains information
that should be acted upon to pre-
vent damaging your machine.
Additional attention statements that
are not preceded by the Attention
Symbol are:
IMPORTANT!
A statement preceded by the word
“IMPORTANT” is one that possesses
special significance.
For additional information, you may
also contact Shindaiwa Inc. at the
address printed on the back of this
manual.
NOTE:
A statement preceded by the word
“NOTE” contains information that is handy
to know and may make your job easier.
WARNING!
Do not make unauthorized modifi-
cations to this machine!
2
Download from Www.Somanuals.com. All Manuals Search And Download.
NOMENCLATURE
Carburetor with Choke
and Primer
Volute Case
Spark Plug
Air Cleaner
Starter
Handle
Exhaust
Outlet
Throttle and
Stop Lever
Fuel Tank
Fuel Filler Cap
Engine
Cover
Handgrip
48002
Swivel
Tube
Flexible
Tube
90° Discharge
Tube
Figure 1
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Model .................................................................................................................. EB501
Dimensions (L x W x H) ..............................................................330 x 375x 475 mm
Engine Type ................... 2 cycle, catalyst, air cooled gas engine, vertical-cylinder
Bore & Stroke.............................................................. 41 x 33 mm (1.6 x 1.3 inches)
Displacement........................................................................ 43.6 cc (2.66 cu. inches)
Fuel/oil ratio............. Gasoline/oil mixture (50:1 with ISO EGD or JASO FC class
2- cycle EngineOil)
Carburetor ............................................. Walbro diaphragm-type with primer pump
Ignition........................................................All transistor electronic ignition system
Spark Plug..............................................................................................Champion CJ8
Starting.................................................................................................... Recoil starter
Stopping ......................................................................... Throttle lever (fuel shut-off)
Fuel Tank Capacity ...........................................................................2.1 liters (71 oz.)
Exhaust System.......................................................................Spark-arrester muffler
Air Filtration .............................................................................................Dry element
Weight (dry; without blower tubes), EB501 .....................................8.6 kg (19 lbs.)
Specifications are subject to change without notice.
Prior to Assembly
Before assembling, make sure you
n Handgrip (removable)
have all the components required for a
complete unit:
n Three Tube Clamps (115 mm,
100 mm, 85 mm) See figure 2.
n 90° Discharge Tube
n Flexible Tube
n Swivel Tube
Standard Tools
n Spark Plug Wrench
n Straight Tube
n Nozzle Tube
n Three Hex Wrenches
(3 mm, 4mm, 5mm)
ASSEMBLING THE BLOWER
1. Place the blower upright on the
ground or a sturdy work surface.
4. Push the swivel tube into the
flexible tube, and then install and
tighten the 85mm clamp over the
rotating band on the swivel tube.
2. Fit the 90° discharge tube over the
blower outlet port, and secure with
the 115mm dia. clamp.
5. Slide the handgrip over the swivel
tube, and secure with the bolt,
washer, and nut.
3. Slip the flexible tube over the oppo-
site end of the 90° discharge tube,
and secure with the 100mm clamp.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLING THE BLOWER (continued)
115mm Clamp
Nut
Swivel
Handgrip
Bolt
Tube
Washer
85mm Clamp
Flexible Tube
48002A
90° Discharge Tube
90° Discharge Tube
100mm Clamp
Swivel Tube
Handgrip
Straight Tube
Nozzle Tube
Flexible Tube
48003
Figure 2
6. Grasp the straight tube as shown,
and push the tube over the
swivel tube locking pins (right).
See figure 3.
Tube Assembly
Align the lock pins with the
lock slots, and push the tubes
together.
7. Lock the straight tube to the swivel
tube by rotating the straight tube.
8. Grasp the nozzle tube and lock the
nozzle to the straight tube as in
Steps 6 and 7.
48004D
IMPORTANT!
Blower tube installation affects blower
balance and performance! Make sure
the tubes and nozzle are correctly
assembled per above, and that all
connections are tight.
Lock Pin
Lock Slot
Rotate clockwise to lock, mak-
ing sure the 3 lines are aligned
on both tubes.
WARNING!
Danger from rotating impeller!
Stop the engine before installing or
removing the blower tubes! Never
perform any maintenance or as-
sembly procedures on this ma-
chine while the engine is running!
48004C
Figure 3
5
Download from Www.Somanuals.com. All Manuals Search And Download.
MIXING FUEL
Fuel Requirements
IMPORTANT!
Mix only enough fuel for your imme-
diate needs! If fuel must be stored
longer than 30-days, it should first
be treated with a stabilizer such as
StaBil™ or equivalent product!
n Use only fresh, clean fuel.
n Use only fuel with an octane rating
of 87 or above.
n Mix all fuel with ISO EGD or JASO
FC class 2-cycle Engine Oil at a
gasoline/oil ratio of 50:1 (1 gallon
gasoline to 2.6 oz. mixing oil).
CAUTION!
Never attempt to mix fuel in the
blower fuel tank! Always mix all fu-
els in a clean, approved container!
CAUTION!
Use of mixing oil other than ISO
EGD or JASO FC rated oil can
lead to exessive carbon deposits.
Some gasolines contain etha-
nol alcohol as an oxygenate!
Oxygenated fuels may cause
increased engine operating tem-
peratures! Under certain condi-
tions, alcohol-based fuels may also
reduce the lubricating qualities of
some mixing oils!
WARNING!
Danger of fire!
Never use any fuel containing
more than 10% ethanol alcohol by
volume!
Never transfer or store fuels in the
presence of combustible materials!
Before starting the engine, always
move the blower to a clear area
at least 10 feet (3 meters) away
from fuels and other combustible
materials!
Generic oils and some outboard
mixing oils are not intended for
use in high-performance air cooled
2-cycle engines, and should never
be used in your Shindaiwa blower!
6
Download from Www.Somanuals.com. All Manuals Search And Download.
FILLING THE FUEL TANK
1. Place the blower upright on the
Remove the
Fuel Filler
Cap
ground or on a sturdy work surface
and wipe any debris from around
the fuel cap.
2. Remove the fuel cap. See figure 4.
3. Fill the tank with clean, fresh fuel
(see page 6).
4. Replace the cap and wipe away
any spilled fuel before starting the
blower engine.
48005
Fuel
Tank
Figure 4
WARNING!
Danger of fire and burn
injury!
n Never smoke or light any fires
near the blower or fuels!
n Always use extreme care when
handling fuel! Fuel is highly flam-
mable!
n Always transport and store fuels
in an approved container!
n Never place flammable material
n Never operate this blower if fuel
system components are damaged
or are leaking!
close to the engine muffler!
n Never operate the blower with-
out a properly functioning muf-
fler and spark arrester installed!
n Never attempt to refuel the
engine while it is running!
n Never operate this blower unless
it is properly assembled and in
good working condition!
n Never attempt to refuel a hot
engine! Always allow the blower
engine to cool before fueling!
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING AND STOPPING THE BLOWER
Danger from thrown dust or de-
WARNING!
Danger from rotating impeller!
bris! Always wear eye and respira-
tory protection when operating this
machine! Never direct the blower
stream toward people or animals!
The impeller will rotate whenever
the blower is operating! Never
operate this blower unless the
intake cover and blower tubes
are properly installed and in good
working order!
Never operate this blower unless
all controls are properly installed
and in good working order.
CAUTION!
Avoid continuous running of the engine without the blower tubes installed,
or if the intake cover or blower tubes are blocked. Doing so can cause
engine overheating resulting in severe engine damage!
Starting Procedure
COLD ENGINE ONLY Choke the
engine by moving the choke control
UP (choke is closed).
WARM OR COLD ENGINE
1. While squeezing the throttle lock
lever, move the throttle lever to the
“engine idle” position. See figure 5.
3. Place the blower on the ground, and
hold the blower firmly with your left
hand on the volute case. See figure 7.
Throttle Positions
Full
Throttle
WARNING!
The engine cover will be hot after
blower operation!
Engine
Idle
48006
Lock Lever
Stop
4. Using your right hand, pull the
starter handle slowly until you feel
the starter engage.
Figure 5
2. Prime the
fuel system
by depress-
ing the
Choke Control (open
position shown)
Pull upward
rapidly
fuel primer
bulb
repeat-
edly until
the bulb
fills with
fuel and
resistance
is felt. See
figure 6.
48007
48008
Fuel Primer Bulb
Figure 7
Figure 6
8
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT!
5. As the starter engages, pull the
starter handle upward rapidly.
If the engine continues to run with the
throttle lever in the “off” position, stop
the engine by moving the choke control
UP to the fully closed position. Adjust
idle setting as decribed on page 10.
6. If necessary, repeat Steps 4 and 5
2–3 times until the engine starts.
CAUTION!
The recoil starter can be damaged
by abuse!
IF THE ENGINE DOES NOT START
Repeat the appropriate starting proce-
dures for “warm” or “cold” engine. If
the engine still will not start, follow the
“Starting a Flooded Engine” procedure
as below:
n Never pull the starter cord to its
full length.
n Always engage the starter
before cranking the engine.
Always rewind the starter cord
slowly.
WARNING!
Never operate the blower unless all
controls are properly installed and
in good working order. Never oper-
ate the blower if the intake cover or
blower tubes are missing or dam-
aged!
WHEN THE ENGINE STARTS
1. As the engine warms, open the
choke gradually by slowly moving
the choke control down to the fully
OPEN position.
2. Run the engine at idle speed until
operating temperature is reached
(2-3 minutes).
STARTING A FLOODED ENGINE
1. Disconnect the spark plug lead,
and use the spark plug wrench to
remove the spark plug in a coun-
ter-clockwise direction (see the
diagram on page 14).
The blower should now be ready
for use.
STOPPING THE ENGINE
1. Cool the engine by allowing it to
run at idle for 2–3 minutes.
2. If the spark plug is fouled or is
soaked with fuel, clean or replace
the plug as required.
2. While squeezing the throttle lock
lever, push and hold the throttle
lever down until the engine stops.
See figure 8.
3. Clear excess fuel from the combus-
tion chamber by cranking the en-
gine several times while the spark
plug is removed.
Throttle
Lever
4. Install and tighten the spark plug,
and reconnect the spark plug lead.
5. Repeat the starting procedures for
“warm engine.”
48009
Squeeze Lock
Lever
6. If the engine still fails to start or
fire, refer to the troubleshooting
flow chart at the end of this manual.
Push Down To Stop
Figure 8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING ENGINE IDLE SPEED
1. Start the engine by following the
procedures described on the pre-
ceding pages. Make sure the thottle
lever is in the "idle" position.
Idle De-
crease
Idle
Increase
2. Run the engine at idle speed until
operating temperature is reached
(2-3 minutes).
3. Loosen the throttle cable locknut.
See figure 9.
Cable
Adjuster
4. Turn the cable adjuster in or out
until the engine idles smoothly at
approximately 2500-3000 rpm.
n Turn the throttle cable adjuster
clockwise to decrease engine idle
speed.
48010
Throttle Cable
Locknut
n Turn the throttle cable adjuster
counter-clockwise to increase en-
gine idle speed.
Figure 9
IMPORTANT!
5. Tighten the throttle cable locknut
securely.
Blower tubes and intake cover must
be in place while adjusting engine
idle! Engine idle speed will also be
affected if either the intake cover or
blower tubes are blocked or incor-
rectly installed!
IMPORTANT!
A clean and unrestricted airflow is
essential to your blower’s engine
performance and durability! Before
attempting any carburetor adjust-
ments, inspect and clean the engine
air filter as described on page 13 of
this manual.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE HARNESS
The Shindaiwa EB501 Blower features
an advanced harness system that helps
ensure maximum operator comfort
and ease of operation.
n The shoulder harness is filled with
soft padding for reduced operator
fatigue.
n The simplified adjustment system
makes it easy to match the harness
to every body size and type. See
figure 10.
Adjustment Holes
Adjusting Strap
The adjusting strap lets the user
determine how far apart the
upper harness loops are
positioned. Easy to
customize for maximum
comfort.
Comfortable
Back Pad
48019
Pull on the loops to
quickly tighten the har-
ness straps
Quick-disconnect
Spring Hook
Quick-adjust
Buckle
To tighten straps…
To loosen straps…
Pull the
quick-
adjust
buckles
up…
Quick-adjust
Buckle
Pull strap
loops down
…and
pull the
straps
down.
48019A
48019B
Figure 10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE BLOWER
n Use low throttle settings when
clearing lightweight materials from
around lawns or shrubbery.
THINK SAFETY!
n Use medium to higher throttle set-
tings to move grass or leaves from
parking lots or walkways.
OPERATING TIPS
In the hands of an experienced opera-
tor, the EB501 can efficiently move a
wide variety of debris ranging from
grass clippings to gravel. As a general
rule, operate your EB501 at the lowest
throttle setting required to get the job
done:
n Use full throttle when moving heavy
loads such as dirt or snow.
IMPORTANT!
Blower noise increases at higher
throttle settings! Always use the low-
est throttle setting required to get the
job done!
Wear eye protection that meets ANSI
Z87.1 such as a face shield or goggles while
operating this machine!
Wear close-fitting clothing to protect
your legs and arms, and Do not wear
clothing or jewelry that could get caught
in machinery! Secure hair so that it is
above shoulder length!
Wear hearing protection
when operating the blower.
Wear a dust mask to reduce the risk
of inhalation injuries.
Always be aware of the strength
and direction of the blower
discharge stream! Never direct the
blower discharge stream toward
people or animals!
48011B
Never operate
the blower if any
component parts are
damaged, loose, or
missing!
Never operate the blower when
visibility is poor.
Figure 11
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUTINE MAINTENANCE EVERY 10 HOURS
IMPORTANT!
(more frequently in dusty conditions)
Remove the Element
Maintenance, replacement or repair of
emission control devices and sys-
tems may be performed by any repair
establishment or individual. However,
warranty repairs must be performed
by a dealer or service center autho-
rized by Shindaiwa Corporation The
use of parts that are not equivalent in
performance and durability to autho-
rized parts may impair the effective-
ness of the emission control system
and may have a bearing on the
Cover Latch
48013
Cover
Element
outcome of a warranty claim.
Snap the cover up from the
bottom to remove.
Figure 12
1. Remove the air cleaner cover by
gently lifting the cover latch. See
figure 12.
WARNING!
Before performing any mainte-
nance on this blower, stop the
engine and disconnect the spark
plug wire!
2. Inspect the filter. If the element is
damaged or distorted, replace it
with a new one.
Daily Maintenance
IMPORTANT!
n Remove dirt and debris from the
The EB501 uses a special high capac-
ity dry-type air filter element. The filter
should not be cleaned with a liquid
cleaner and must NEVER be oiled!
blower exterior.
n Inspect the engine, tank, and hoses
for possible fuel leaks, and repair as
necessary.
3. Tap filter gently on a hard surface
to disloge debris from element or
use compressed air to blow debris
from the air filter element.
n Inspect the entire blower for loose,
damaged, or missing components,
and repair as necessary.
n Inspect the engine cooling fins for
accumulations of dirt or debris, and
clean as necessary.
IMPORTANT!
Direct the air stream at the inside face
of the filter only!
CAUTION!
4. Wash the filter cover with soap and
water and blow dry.
Dirty or damaged cooling system
components may allow the engine
to overheat, possibly causing seri-
ous engine damage!
5. Install the filter element and cover
in the reverse order of removal.
Operating the blower with loose,
missing, or damaged components
could allow the engine to over-
speed, possibly causing serious
engine damage!
CAUTION!
Never operate the blower if the air
cleaner assembly is damaged or
missing!
13
Download from Www.Somanuals.com. All Manuals Search And Download.
EVERY 10/15 HOURS
EVERY 50 HOURS
(more frequently if reduced
performance is noted)
to remove
n INSPECTION Inspect the entire
blower and tubes for damage,
including loose or missing compo-
nents, and repair as necessary.
n SPARK PLUG Replace the spark
plug with a Champion CJ8 or
equivalent, gapped to 0.024 inch
(0.6mm).
48017
0.024" (0.6mm) gap
Champion CJ8
Wire
Hook
Spark Plug
48014
Figure 14
1. Use the spark plug wrench to re-
move the spark plug (turn counter-
clockwise to remove). See figure
13.
48015
Fuel Filter
Fuel Tank
2. Clean and adjust the spark plug
gap to 0.024” (0.6mm). Replace any
damaged or visibly worn plug with a
Champion CJ8 or equivalent. See
figure 13.
Figure 14
FUEL FILTER Use a bent piece of
wire to extract the fuel filter from in-
side the fuel tank, and then remove
and replace with a new element. See
figure 14.
3. Install the spark plug finger-tight
in the cylinder head, then tighten it
firmly with the spark plug wrench.
Avoid overtightening.
CAUTION!
Do not nick or perforate fuel tube
with wire hook!
CAUTION!
Never allow dirt or debris to enter
the cylinder bore! Before removing
the spark plug, thoroughly clean
the spark plug and cylinder head
area!
Before reinstalling the filter, inspect
the condition of the fuel line. If
damage or deterioration are noted,
the blower should be removed from
service until it can be inspected by a
Shindaiwa-trained service technician.
Allow the engine to cool before
servicing the spark plug! Cylinder
threads can be damaged by tight-
ening or loosening the spark plug
while the engine is hot!
n COOLING SYSTEM Use a wood
or plastic scraper and a soft brush
to remove dirt and debris from the
cylinder fins and crankcase.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
135-HOUR MAINTENANCE
Every 135 hours of operation,
Muffler Body
remove and clean the muffler.
First, remove the
spark plug
Remove the Engine Cover
Engine Cover
Muffler Screw
Retaining Tab
Engine
Cover
48016D
Arrester
Screen
5 mm
Lower
Screw
6 mm
Muffler
Screws
48018
Remove four Allen-
head capscrews
Figure 15
Gasket
WARNING!
Exhaust
Tube
Never operate the machine with
a damaged or missing muffler
or spark arrester! Operating with
Tail Cap
missing or damaged exhaust com-
ponents is a fire hazard and could
also damage your hearing.
Mounting
Screws
Figure 16
5. Use a plastic scraper or wire brush to
remove carbon deposits from the arrester
screen, exhaust tube and tail cap.
Remove the Muffler.
1. Remove the spark plug.
6. Inspect the screen carefully, and replace
any screen that has been perforated, dis-
torted, or is otherwise unserviceable.
2 Use the 4mm Allen wrench to remove
the four engine cover screws , and
then slide the cover from the engine
taking care not to misplace the cyl-
inder-to-cover insulating gasket. See
figure 15.
7. Gently tap the muffler on a wood surface
to dislodge any loose carbon.
8. Inspect the cylinder exhaust port for
carbon buildup.
3. Pry the muffler screw retaining
tabs away from the screw heads and
remove the two 6 mm muffler screws.
Remove the 5 mm lower muffler
IMPORTANT!
If you note excessive carbon buildup, con-
screw, then remove the muffler assem- sult your servicing dealer.
bly from the engine. See figure 16.
9. Reassemble the muffler in the reverse
order of disassembly.
Remove the Spark Arrester.
4. Use the screwdriver to remove the
three exhaust tube mounting screws,
and then remove the tail cap, exhaust
tube, gasket, and arrester screen. See
figure 16.
IMPORTANT!
Reset the muffler screw retaining tabs to
prevent the muffler screws from loosening.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE (30 days or longer)
n CLEANING Thoroughly clean the
n LUBRICATION Remove the spark
plug, and then pour approximately
1/4-oz of 2-cycle oil into the cylinder
through the spark plug hole. Before
reinstalling the spark plug, pull the
recoil starter gently 2–3 times to
distribute the oil over the cylinder
walls.
blower exterior.
n INSPECTION Inspect the entire
blower and tubes for damage,
including loose or missing compo-
nents, and repair as necessary.
n FUEL Drain the fuel tank, and then
clear any remaining fuel from the
carburetor and lines by running the
blower until it stops from lack of fuel.
n AIR CLEANER Remove, clean,
and reinstall the filter element as
described under “daily mainte-
nance.”
CAUTION!
n STORAGE Store the blower in a
Never store this product with
any fuel remaining in the tank,
fuel lines, or carburetor! Your
Shindaiwa warranty does not in-
clude coverage for damage caused
by “stale” or contaminated fuels!
clean, dry, dust-free environment.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
ENGINE DOES NOT START
What To Check
Possible Cause
Remedy
Consult with an authorized
servicing dealer.
Faulty recoil starter.
Fluid in the crankcase.
Internal damage.
Does the engine
crank?
NO
NO
NO
YES
Loose spark plug.
Excess wear on
cylinder, piston, rings.
Tighten and re-test.
Consult with an authorized
servicing dealer.
Good
compression?
YES
Fuel/mixture incorrect,
stale, contaminated.
Refill with fresh fuel of the correct
mixture (gasoline and ISO EGD
or JASO FC class 2-cycle Engine Oil).
Does the tank
contain fresh
fuel of the
proper grade?
YES
Check for clogged fuel
filter and/or vent.
Clean as required;
re-start.
Is fuel filling the
fuel primer bulb
during priming
operations?
NO
NO
YES
Consult with an authorized
servicing dealer.
Faulty ignition ground.
Is there spark at
the spark plug
wire terminal?
YES
If the plug is wet, excess Crank the engine with the
Check the
spark plug
fuel may be in the
cylinder.
plug removed, replace the
plug, and re-start.
The plug may be fouled
or improperly gapped.
Clean and re-gap the plug to
0.24 inch (0.6 mm); re-start.
The plug may be
damaged internally or
of the wrong size.
Replace the plug with a
Champion CJ8.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE (continued)
LOW POWER OUTPUT
Possible Cause
What To Check
Remedy
Use lower throttle setting.
Is the engine over-
heating?
Operator is overworking
the machine.
Refill with fresh fuel of the cor-
rect mixture (gasoline and ISO
EGD or JASO FC class 2-cycle
Engine Oil, 50:1 ratio.
Improper fuel/oil ratio.
Fallen leaves or dust on
the intake cover.
Clean the intake cover.
Fan, fan cover, or cylinder Clean, repair or replace as
fins are dirty or damaged.
necessary.
Decarbonize muffler.(See 135
hr. maint. page 15).
Carbon deposits in the
muffler.
Consult with an authorized
servicing dealer.
Carbon deposits in the
combustion chamber
and/or exhaust port.
Missing or damaged
blower tubes.
Replace missing or damaged
blower tubes.
Clogged air cleaner
element.
Clean or replace air cleaner
element.
Engine is rough
at all speeds. May
also have black
smoke and/or
unburned fuel at
the exhaust.
Loose or damaged
spark plug.
Tighten or replace.
Air leakage or
clogged fuel line.
Repair or replace filter and/
or fuel line.
Drain the fuel system, replace
the fuel.
Water in the fuel.
Piston seizure.
Consult with an authorized
servicing dealer.
Faulty carburetor
and/or diaphragm.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE (continued)
ADDITIONAL PROBLEMS
What To Check
Possible Cause
Remedy
Idle engine until cool; find
reason for overheat.
Overheating condition.
Engine is
knocking.
Check fuel octane rating.
Check for presence of
alcohol in fuel. Refuel as
necessary.
Improper fuel.
Consult with an authorized
servicing dealer.
Carbon deposits in
combustion chamber
and/or exhaust port.
Clogged air cleaner
element.
Clean the element.
Poor
acceleration.
Spark arrester is
clogged.
Clean the Spark arrester.
(page 15).
Clogged fuel filter.
Replace fuel filter.
Carburetor mixture
too lean.
Consult with an authorized
servicing dealer.
Idle speed set too low.
Set to 2500-3000 RPM.
Leaking or damaged
blower housing or tube
assembly.
Repair or replace components
as required.
Debris is tangled in
Consult with an authorized
Egine difficult
to shut off.
blower impeller blades. servicing dealer.
Overheated engine.
Idle engine to cool.
Throttle cable is
incorrectly adjusted.
Choke engine to stop.
Adjust thottle cable.
Overheating due to
incorrect spark plug.
Replace spark plug with
Champion CJ8.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE (continued)
ADDITIONAL PROBLEMS
What To Check
Possible Cause
Remedy
Move throttle lever to the
run position and reststart.
Throttle lever is the
''OFF'' position.
Engine stops
abruptly.
Refuel.
Fuel tank empty.
Clogged fuel filter.
Water in the fuel.
Replace fuel filter.
Drain; replace with clean
fuel. Replace fuel filter.
Shorted spark plug or
loose terminal.
Clean or replace spark plug;
tighten the terminal.
Ignition failure.
Piston seizure.
Consult with an authorized
servicing dealer.
Excessive
vibration.
Consult with an authorized
servicing dealer.
Warped or damaged
blower fan.
Consult with an authorized
servicing dealer.
Loose bolt or fastener
Tighten as required.
Internal engine damage.
Consult with an authorized
servicing dealer.
Replace cushions.
Remove debris.
Damaged A-V cushions.
Engine over-
speeding.
Blower intake or
discharge ports or tubes
are clogged with debris.
Consult with an authorized
servicing dealer.
Impeller blades are
missing or damaged.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
The following statement only applies to United States and its territories
Shindaiwa Corporation
Federal Emission Design And Defect Limited Warranty
Utility And Lawn And Garden Engines
deny your warranty coverage if your engine
or a part has failed due to abuse, neglect,
improper maintenance or unapproved
modifications.
Shindaiwa Corporation warrants to the
initial purchaser and each subsequent
owner, that this utility equipment en-
gine (herein engine) is designed, built
and equipped to conform at the time of
initial sale, to all applicable regulations
of the U.S. Environmental Protection
Agency (EPA), and that the engine is
free of defects in materials and work-
manship that would cause this engine
to fail to conform with EPA regula-
tions during its warranty period. This
emission warranty is applicable in all
States, except the State of California.
You are responsible for presenting your
engine to the nearest dealer authorized by
Shindaiwa Corporation when a problem
exists.
If your Shindaiwa Dealer is unable to
answer questions regarding your warranty
rights and responsibilities, you should then
contact your Shindaiwa Distributor.
For the name and telephone number of
the Shindaiwa Distributor in your area,
please call Shindaiwa Inc. at (503) 692-3070
between the hours of 8:00 AM and 5:00 PM
Pacific Standard Time.
For parts listed under PARTS
COVERED, the dealer authorized by
Shindaiwa Corporation will, at no cost
to you, make the necessary diagnosis,
repair, or replacement of any defective
emission-related component to ensure
that the engine complies with appli-
cable U.S. EPA regulations.
PARTS COVERED
Listed below are the parts covered by
the Federal Emission Design and Defect
Warranty. Some parts listed below may
require scheduled maintenance and are
warranted up to the first scheduled replace-
ment of that part. The warranted parts
include:
MANUFACTURERS WARRANTY
COVERAGE
When sold within the U.S., this engine’s
emission control system is warranted for a
period of two (2) years from the date this
product is first delivered to the original
retail purchaser.
1. Carburetor Internal Components
• Valve Assembly-throttle, Jet, Metering
Diaphragm
2. Ignition System Components
• Ignition Coil
OWNER’S WARRANTY
RESPONSIBILITIES
• Flywheel Rotor
As the engine owner, you are responsible
for the performance of the required
maintenance listed in your owner’s manual.
Shindaiwa Corporation recommends that
you retain all receipts covering main-
tenance on your engine, but Shindaiwa
Corporation cannot deny a warranty claim
solely for the lack of receipts or for your
failure to ensure the performance of all
scheduled maintenance.
The emission control system for your par-
ticular Shindaiwa engine may also include
certain related hoses and connectors.
LIMITATIONS
The Federal Emission Design and Defect
Warranty shall not cover any of the follow-
ing:
(a) conditions resulting from tamper-
ing, misuse, improper adjustment
As the engine owner, you should however
be aware that Shindaiwa Corporation may
21
Download from Www.Somanuals.com. All Manuals Search And Download.
(unless they were made by the
dealer or service center authorized
by Shindaiwa Corporation during
a warranty repair), alteration, acci-
If other than the parts authorized by
Shindaiwa Corporation are used for main-
tenance replacements or for the repair of
components affecting emission control,
dent, failure to use the recommend- you should assure yourself that such parts
ed fuel and oil, or not performing
required maintenance services,
are warranted by their manufacturer to
be equivalent to the parts authorized by
Shindaiwa Corporation in their perfor-
mance and durability.
(b) the replacement parts used for
required maintenance services,
(c) consequential parts used for re-
quired maintenance services,
OBTAINING WARRANTY SERVICE
All repairs qualifying under this limited
warranty must be performed by a dealer
authorized by Shindaiwa Corporation
(d) diagnosis and inspection fees that
do not result in eligible warranty
service being performed, and
If any emission-related part is found defec-
tive during the warranty period, it is your
responsibility to present the product to an
authorized Shindaiwa dealer. Bring your
sales receipts showing the date of purchase
for this engine. The dealer authorized by
Shindaiwa Corporation will perform the
necessary repairs or adjustments within a
reasonable amount of time and furnish you
with a copy of the repair order. All parts
and accessories replaced under this war-
ranty become the property of Shindaiwa
Corporation
(e) any non-authorized replacement
part, or malfunction of authorized
parts due to use of non-authorized
parts.
MAINTENANCE AND REPAIR
REQUIREMENTS
You are responsible for the proper use and
maintenance of the engine. You should
keep all receipts and maintenance records
covering the performance of regular main-
tenance in the event questions arise. These
receipts and maintenance records should
be transferred to each subsequent owner
of the engine. Shindaiwa Corporation re-
serves the right to deny warranty coverage
if the owner has not properly maintained
the engine. Shindaiwa Corporation will
not deny warranty repairs, however, solely
because of the lack of repair, maintenance
or failure to keep maintenance records.
To locate an authorized Shindaiwa
dealer near you, contact your Shindaiwa
Distributor. For the name and telephone
number of the Shindaiwa Distributor in
your area, please call Shindaiwa Inc. at
(503) 692-3070 between the hours of 8:00
AM and 5:00 PM Pacific Standard Time.
THIS WARRANTY IS
ADMINISTERED BY
MAINTENANCE, REPLACEMENT OR
REPAIROFEMISSIONCONTROLDEVICES
AND SYSTEMS MAY BE PERFORMED
BY ANY REPAIR ESTABLISHMENT OR
INDIVIDUAL; HOWEVER, WARRANTY
REPAIRS MUST BE PERFORMED
BY A DEALER OR SERVICE CENTER
A U T H O R I Z E D B Y S H I N D A I WA
CORPORATIONTHEUSEOFPARTSTHAT
ARENOTEQUIVALENTINPERFORMANCE
AND DURABILITY TO AUTHORIZED
PARTSMAYIMPAIRTHEEFFECTIVENESS
OF THE EMISSION CONTROL SYSTEM
AND MAY HAVE A BEARING ON THE
OUTCOME OF A WARRANTY CLAIM.
Shindaiwa Inc.
11975 S.W. Herman Rd.
Tualatin OR. 97062
(503) 692-3070
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Shindaiwa Inc.
11975 S.W. Herman Rd.
Tualatin, Oregon 97062 USA
Telephone: 503 692-3070
Fax:
503 692-6696
Shindaiwa Corporation
Head Office:
6-2-11, Ozuka-Nishi
Asaminami-Ku, Hiroshima
731-3167, Japan
Telephone: 81-82-849-2220
Fax:
81-82-849-2481
© 2006 Shindaiwa, Inc.
Part Number 68232-94011
Printed in Japan
Shindaiwa is a registered trademark
of Shindaiwa, Inc.
Specifications subject to change without
notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
|