SHENZHEN HONGDIAN TECHNOLOGIES CO., LTD.
Mobile Data Communications
User Manual
Galaxy Mobile Router
(H7920)
Download from Www.Somanuals.com. All Manuals Search And Download.
HLR
Home Location Register
High Speed Circuit Switch Data
Internet Group Management Protocol
Internet Gateway Routing Protocol
Intelligent Network
HSCSD
IGMP
IGRP
IN
Abbreviations
APN
Access Point Name
APP
Application
IP
Internet Protocol
ATM
ATM
AuC
Asynchronous Transfer Mode
Auto Table Machine
IPv4
IP version 4
IPv6
IP version 6
Authentication Centre
IPSEC
ISDN
ISP
IP Secure Protocol
BG
Border Gateway
Integrated Services Digital Network
Internet Service Provider
Layer 2 Tunneling Protocol
Location Area
BGP
BSC
Border Gateway Protocol
Base Station Controller
L2TP
LA
BSS
Base Station System
BSSGP
BTS
BSS GPRS Protocol
LLC
Logical Link Control
Base Transceiver System
Code Division Multiple Access
Call Detail Record
MAP
MDNS
MDTU
MIB
Mobile Application Part
Mobile Domain Name System
Mobile Data Terminal Unit
Management Information Base
Mobile Station
CDMA
CDR
CGF
Charging Gateway Function
Command Line Interface
Circuit Switch Data
CLI
MS
CSD
DDN
DHCP
DMZ
DNS
MSC
MT
Mobile Switching Center
Mobile Terminal
Digital Data Network
Dynamic Host Configuration Protocol
DeMilitarized Zone
MTBF
MTTR
N/A
Mean Time between Failures
Mean Time to Recovery
Not Applicable
Domain Name System
DSC
DTU
Data Service Center
NAS
NAT
Network Access Server
Network Address Translation
Network Time Protocol
Operations & Maintenance
Password Authentication Protocol
Packet Data Protocol
Data Terminal Unit
EDGE
EGP
EIGRP
EMC
ESP
Enhanced Data Rate for GSM Evolution
External/Exterior Gateway Protocol
External/Exterior Internet Group Routing Protocol
Electro Magnetic Compatibility
Electro Static Precautions
European Telecommunications Standards Institute
Gateway GPRS Support Node
Gateway MSC
NTP
O&M
PAP
PDP
PDN
PDSN
PLMN
POS
PTM-G
PTM-M
QoS
Packet Data Network
ETSI
GGSN
GMSC
GMSK
GPRS
GSM
GSN
GTP
Packet Data Serving Node
Public Land Mobile Network
Point of Sales
Gaussian Minimum Shift Keying
General Packet Radio Service
Global System for Mobile Communications
GPRS Support Node
Point-to-Multipoint Group Call
Point-to-Multipoint Multicast
Quality of Service
RA
Routing Area
GPRS Tunneling Protocol
GTP Identity
RADIUS
RIP
Remote Authentication Dial In User Service
Routing Information Protocol
GTP-id
Download from Www.Somanuals.com. All Manuals Search And Download.
RSC
Register Service Center
RTOS
RTP
Real Time Operating System
Real-time Transport Protocol
Remote Terminal Unit
RTU
RSVP
SCADA
SGSN
SIM
Resource reSerVation Protocol
Supervisory Control and Data Acquisition
Serving GPRS Support Node
Subscriber Identify Module
Short Message Service
SMS
SMSC
SNMP
STK
Short Message Service Center
Simple Network Management Protocol
SIM Tool Kits
TCP
Transmission Control Protocol
Time Division Multiple Access
Telecommunication Managed Network
User Datagram Protocol
TDMA
TMN
UDP
UIM
User Identify Module
UMTS
USSD
UTK
Universal Mobile Telecommunication System
Unstructured Supplementary Service Data
UIM Tool Kits
VLR
Visitor Location Register
WAN
WAP
WDDN
Wide Area Network
Wireless Application Protocol
Wireless Digital Data Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
CHAPTER 3 ROUTER CONFIGURATION ............................................................14
3.1 CONNECTION............................................................................................................14
3.2 CONFIGURATIONS..................................................................................................18
3.2.1 ROUTER STATUS ..................................................................................................21
3.2.2 ONLINE HELP ........................................................................................................22
3.2.3 SYSTEM TOOLS.....................................................................................................23
3.2.4 NETWORK SETTING............................................................................................27
3.2.5 ROUTE CONFIGURATION ..................................................................................34
3.2.6 SPECIAL SETTING................................................................................................40
3.2.7 HONGDIAN PRODUCTS.......................................................................................47
3.2.8 LOGOFF...................................................................................................................47
3.2.9 FIRMWARE UPDATE............................................................................................47
3.3 CLI OPERATION....................................................................................................48
CHAPTER 4 OPERATION INSTRUCTION............................................................49
4.1 PANEL INDICATION................................................................................................49
4.2 OPERATION...............................................................................................................50
4.3 TROUBLE SHOOTING.............................................................................................50
APPENDIX 1: HYPERTEXT TERMINAL SETTING.................................................52
APPENDIX 2: FIRMWARE UPDATE TOOL ..............................................................56
CHAPTER 1 INTRODUCTION ...................................................................................1
1.1 GENERAL .....................................................................................................................1
1.2 SYSTEM FEATURES ..................................................................................................2
1.3 SPECIFICATIONS .......................................................................................................3
1.4 TYPICAL APPLICATIONS........................................................................................4
1.5 TYPES DESCRIPTION ...............................................................................................7
CHAPTER 2 INSTALLATION.....................................................................................8
2.1 GENERAL .....................................................................................................................8
2.2 OPEN BOX ....................................................................................................................8
2.3 INSTALLATION AND CABLE CONNECTION......................................................8
2.4 GROUND .....................................................................................................................12
2.5 POWER SUPPLY .......................................................................................................12
2.6 CHECK THE MOBILE NETWORK .......................................................................13
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 1: Introduction
Galaxy H7920 Mobile Router User Manual
Chapter 1: Introduction
GPRS network theoretically can provide a maximum bandwidth 171.2Kbps,
actually; it works at 40~100Kbps bandwidth (it depends on service provider’s
operation policy). As we know, GPRS is packet based network which provides
TCP/IP communication channel.
Chapter 1 Introduction
This chapter introduces the Galaxy H7920 Mobile Router general
descriptions, features and philosophy.
Same as GPRS/EDGE network, CDMA 1x network can provide a maximum
bandwidth up to 300Kb/s and actual transmitting and receiving bandwidth
reaches 100Kb/s.
1. General
2. System Features
3. Specifications
4. Typical Applications
5. Types Description
Typical center to multipoint system configuration plan is as below.
1.1 General
2.5G mobile communication technology (GPRS/EDGE/CDMA 1x) has become
widely used of industrials and utilities in recent years and many customers are
seeking reliable, flexible and cost-effective data channel to build their
information system. Many applications such as ATM, POS, SCADA and
surveillance system will require data channels covered all country; this brings a
bright future for GPRS/EDGE and CDMA 1x data networks applications.
GPRS or
CDMA 1X
Network
Requirements towards information system are varied because of different
features of numerous industrial applications. Mobile telecom service providers
are required to provide industrial application solutions not only meeting common
specifications and also individual special ones. Hence, Hongdian co-operates
with mobile service providers to design products and network configurations
suitable to industrial end users’ individualized applications. Hongdian has
developed embedded, advanced and reliable Galaxy mobile (GPRS/EDGE/CDMA
1x) router for the applications.
Internet
Video Server
Requirements are different from customer to customer; below paragraphs will
describe the typical applications.
Since Hongdian has many years experience of mobile data communication, it
proves that Hongdian products are widely applied and work stably. Galaxy router
is a dedicated ideal data transmission channel for industrial applications. The
manual explains setup procedure of H7920 router and provides the system
operation guide.
1.2 System Features
Basic Features
ꢀ
GPRS/EDGE Part
ꢁ
Support dual band GSM/GPRS/EDGE
ꢁ
Complies with ETSI GSM Phase 2+Standard
ꢀ
CDMA Part
ꢁ
ꢁ
ꢁ
Support 800/1900MHz band
Complies with FCC/SAR and CDG 1/2&3
Real time clock
M80-792001-01
M80-792001-01
1
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 1: Introduction
Galaxy H7920 Mobile Router User Manual
Chapter 1: Introduction
Power
Enhanced Features
ꢀ
ꢀ
Voltage: +5VDC(+7.5~24VDC Optional)
Consumption
ꢀ
ꢀ
ꢀ
ꢀ
Support multiple protocol conversion
Support data center and network management
Online detection and redial
ꢁ
Max. current: 430mA@+5VDC
Standby: 30mA@+5VDC
ꢁ
Online/Offline control
ꢁ
ꢁ
ꢁ
Online/Offline controlled by user’s equipment
Online/Offline triggered by user’s data
Timing online/offline
Others
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Measurement: 98x100x23 (not including antenna and fixed parts)
Weight: 230g
Operation temperature: -10~+50ºC
Store temperature: -20~+75ºC
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
STK/UTK card special function configuration
Support Ethernet and RS-232/485 interface
Synchronize with CDMA network
Self-diagnostic
Relative humidity: 95%(non-condensing)
Optimize EMC design
1.4 Typical Applications
Advanced Features
Galaxy router typical applications are described as below.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Built-in DHCP server
Firewall and NAT
Support DMZ
Support dynamic DDNS
Support VPN (Optional)
Support path routing
Support envelop filtering
Support mobile network traffic counting
Support SNMP V1, V2c (V3 ready)
Support NTP
Support Ethernet or dial-up network backup
WEB/Telnet management interface
Acquire specify PPP server IP address
Local/Remote firmware upgrade
Local/Remote configuration profile backup
Application 1: Direct connection
Refer to following diagram, connect Galaxy router to your terminal.
GPRS or
CDMA 1X
Network
Internet
1.3 Specifications
Application 2: Center to multipoint
Galaxy router specifications
GPRS/EDGE data
For industrial applications, it requires a device to collect information from
discrete remote sites. The application show as below diagram is a typical video
surveillance configuration. You can connect Galaxy router to a net-camera and
then setup the Data Service Center (DSC) IP address or domain name at Galaxy
router.
ꢀ
ꢀ
ꢀ
GPRS/EDGE Class 2~10
Code plan: CS1~CS4
Complied with SMG31bis specifications
CDMA 1x data
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Support IS 707 data service
Support 153kbps packet data
Support Class 2.0 Group 3 facsimile
CDMA 2000 spread spectrum
Complied with IS-95A, IS-95B CDMA interface
Interface
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Antenna: 50Ω/SMA Female
SIM/UIM: 3V
Serial port (DB9): RS-232(DCE) or RS-485 (Optional)
Serial port data rate: 300~115,200 bits/s
Ethernet interface: 10/100BaseT/RJ45 (Auto sense)
Configuration: WEB/Telnet or RS-232
M80-792001-01
M80-792001-01
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 1: Introduction
Galaxy H7920 Mobile Router User Manual
Chapter 1: Introduction
GPRS or
CDMA 1X
Network
Internet
GPRS or
CDMA 1X
Network
Internet
RS-232
RS-232
Serial port/Mobile network transmission
It is the solution to convert and transmit non IP device data over TCP/IP based
mobile data network (GPRS/EDGE/CDMA 1x). Connect the non IP device to the
Galaxy serial port.
Video Server
GPRS or
CDMA 1X
Application 3: Ethernet connection
Network
RS-232
Galaxy router can be configured as following network applications.
Internet
ꢂ
ꢂ
ꢂ
Ethernet/Mobile network routing.
Serial port/Ethernet converter.
Serial port/Mobile network transmission.
Ethernet/Mobile network routing
Application 4: Mobile Network/PSTN backup
By connecting your LAN and mobile network (WAN), you can share the
GPRS/EDGE or CDMA 1x access to your LAN by built-in NAT (Network Address
Translation) technologies. Therefore, multiple IP terminals or PCs can share the
Internet access via Galaxy router.
Galaxy H7920 can be connected to mobile network, PSTN dialup network and
Ethernet, those channels can be backup each other with the built-up backup
function.
Bellow diagram is a typical solution for finance application. At the normal
situation, the transaction data generated by POS or ATM will be transmitted via
GPRS/EDGE or CDMA 1X network. When the mobile network failed, Galaxy
router will dial the modem connected at its COM port, and then route the data via
the dial-up channel. It is a very useful solution for finance application and other
applications that requires high availability.
GPRS or
CDMA 1X
Network
Internet
Serial port/Ethernet converter
For many non IP traditional terminals, you can also connect your non IP
terminals to Galaxy router via RS232/485 interface. After then, your non IP
terminal will become standard TCP/IP 10/100BaseT interface network
equipment. It is possible to connect many non IP terminals to IP network at
same place.
M80-792001-01
M80-792001-01
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 1: Introduction
Galaxy H7920 Mobile Router User Manual
Chapter 2: Installation
Chapter 2 Installation
POS
Router
GPRS/EDGE
CDMA
This chapter describes the Galaxy router installation procedures, power on and initial setup.
1. General
Galaxy H7920
2. Open Box
3. Installation and Cable Connection
4. Grounding
5. Power Supply
6. Check the Mobile Network
PSTN
V.90 Modem
PSTN backup
2.1 General
ATM
Galaxy router should be installed and configured properly before putting it in
service. The installation and configuration should be done or supervised by
Hongdian qualified engineer.
1.5 Types Description
Galaxy router is a product designed at Hongdian platform with customer
specified application options. It complies with the different industrial applications
and different service provider mobile data network. In order to identify different
products, we explain the type name as below:
Attention:
Do not install Galaxy router or connect/disconnect its cable when it is power on.
Galaxy router type: H7920-XYZn
ꢃ
H7920
X-Data
Y-Mobile network
Zn- Radio Module
Manufacturer*
A-AnyData
B-BenQ
E-Sony Ericsson
H-Huawei
interface
2.2 Open Box
Hongdian Galaxy
mobile router
R-Router
C-CDMA network
E-EDGE Network
G-GPRS network
In order to protect products during shipment, Galaxy mobile router has been
packed properly. You may need to keep the packing materials for reshipping
after you open the pack box.
H7920 platform
M-Motorola
S-Siemens
W-Wavecom
Z-ZTE
Galaxy mobile router package includes.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Galaxy mobile router
+5V power adapter
Fixed part
CAT-5 UTP cable
User manual
1 (packed according order)
1 (+12V power adapter Optional)
1 pair
1
1 (CD-ROM)
1
……
* Z=Radio Module Manufacturer, n=Radio Module (can be null), i.e.:
M2=Motorola G24
Qualified & Repair Card
For Example: H7920-RGM2 -- Galaxy GPRS Router, built-in with Motorola G24
radio module.
Optional accessories
ꢀ
ꢀ
ꢀ
ꢀ
Standard antenna
Vehicle antenna
Directional antenna
Coaxial feeder (SMA interface)
After you open the box, you should count it carefully with your purchase order.
2.3 Installation and Cable Connection
Installation requirements
ꢀ
A PC with Ethernet interface and TCP/IP protocol
ꢁ
ꢁ
IE5.0 or up Internet browser
1024x768 monitor
M80-792001-01
M80-792001-01
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 2: Installation
Galaxy H7920 Mobile Router User Manual
Chapter 2: Installation
ꢀ
A valid GPRS/EDGE SIM card or CDMA 1X UIM card (Depends router
type)
Panels
ꢀ
Front Panel
Galaxy router should be placed on desktop, wall or any other fixed place. There
is no special requirement for wiring and heating dispersion. However, it is
required to place Galaxy router apart from:
ꢀ
ꢀ
ꢀ
Heating device
Dusty and moist environments
Interference source, such as metal wall, microwave oven
The antenna should be installed at correct place and angle to ensure the
GPRS/EDGE or CDMA 1x signal receiving. Do not install antenna inside of metal
cabinet.
Measurement
The below diagram is Galaxy router outside and installation measurement.
Galaxy H7920 Router Front Panel
LED description:
ꢂ
ꢂ
ꢂ
10M: 10BaseT LED, lights up when connected with 10M link.
LINK: LAN LED, lights up when connected.
NET: Radio network LED, blinking during login, lights up when logged
in (Depends network, check the definitions at Online Help).
RUN: Galaxy router LED, blinking means normal operation.
ꢂ
宏电
The SIM or UIM card can be inserted and released by pressing the SIM/UIM card
drawer button.
Hongdian
ꢀ
Rear Panel
Galaxy
CDMA 1x路由器
All Galaxy router connectors are located at the rear panel.
型号：H7920-RCZ
接口：RS-232/Ethernet
电源：＋7.5~+12VDC
深圳市宏电技术开发有限公司
Shenzhen Hongdian Technologies Co., Ltd.
Made in Shenzhen, China
T N A
E T E S R
C D
5 4 J R
M
C O
Galaxy Router Rear Panel
M80-792001-01
M80-792001-01
9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 2: Installation
Galaxy H7920 Mobile Router User Manual
Chapter 2: Installation
Connectors’ description:
ꢂ
ꢂ
ꢂ
COM: Serial port (RS-232/485), serial data port or console port.
RJ45: 10/100BaseT auto sense Ethernet interface.
DC: DC power supply interface (+5VDC, +7.5V~+24VDC optional,
check the label before power on.)
ꢂ
ꢂ
RESET: Reset button, press and hold for 5 seconds to reset the
Galaxy router back to its default factory configurations.
ANT: Antenna interface (SMA female), standard, vehicle antenna,
directional antenna optional.
RS-232 Modem
RS-232 DB9 (Male)
RS-232 DB9 (Male)
Click “Start” -> “System Tools” -> “Default Setting” to reset the Galaxy router
back to its default factory configurations. If you have forgotten the login
password, press and hold RESET button for 5 seconds.
CD
RX
TX
DTR
GND
DSR
RTS
CTS
RING
1
2
3
4
5
6
7
8
9
1 CD
2 RX
3 TX
4 DTR
5 GND
6 DSR
7 RTS
8 CTS
9 RING
The Galaxy router will be back to the factory default configurations if the RESET
button is pressed up to 5 seconds.
ꢆ
Management webpage address: 192.168.8.1
Login name: admin, Password: hongdian
Interface and cable connection
RJ45 – Ethernet
COM – Serial Port
It is standard 10/100BaseT Ethernet interface (Auto sense).
COM serial port is standard, DB9 (Female) RS-232(DCE) interface (RS-485
optional); it can be assigned to CONSOLE port or data port.
DC – Power
DC power supply interface (+5VDC, +7.5V~+24VDC optional, check the label
before power on.)
RS-232(DCE) connector PIN definition:
DB-9 connector (DCE-Female)
The power adapter output current should be not less 2A; Power supply ripple
should be less 300mV.
PIN
1
Signal
CD
Description
Carrier Detect
Received Data
Transmitted Data
Data Terminal Ready
Signal Ground
Direction Note
--ꢄ
ꢅ--
--ꢄ
ꢅ--
2
3
4
5
6
7
8
9
RXD
TXD
DTR
GND
DSR
RTS
CTS
RI
ANT - Antenna
Standard 5OΩ/SMA RF connector (Female)
For outdoor use, lightning should be considered. We propose to install an
arrester between antenna and the ANT interface.
Data Set Ready
Request To Send
Clear To Send
--ꢄ
ꢅ--
--ꢄ
--ꢄ
2.4 Ground
Ring Indicator
To ensure a safe, stable and reliable Galaxy mobile router operation, DTU
cabinet should be grounded properly. Connect the Galaxy mobile router cabinet
to site ground wire.
For CONSOLE mode, the PC serial port that connects the Galaxy router should be
configured to 57600, 8, N, 1; and then you can start a Hypertext Terminal at the
PC, type commands to manage Galaxy router.
2.5 Power Supply
Galaxy router has a feature of the dial-up backup routing. Customer can connect
a dial-up modem to the router COM port. A special cable will be required. The
detail cable wiring is showed at the below diagram.
Galaxy router is designed with advanced power management technologies; it
can operate standalone. The input DC power voltage is +5VDC (+7.5V~+24VDC
optional). You should check the Galaxy router label before power on.
The power adapter output current should be not less 2A; Power supply ripple
should be less 300mV.
M80-792001-01
M80-792001-01
11
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 2: Installation
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Attention!
ꢁ
Normally, the power supply is +5VDC, +7.5V~+24VDC is optional. You
should check the Galaxy router label before power on.
Galaxy router should be powered by the AC adapter supplied by Hongdian.
Hongdian will not guarantee Galaxy router performance if it is powered by
any other unqualified AC adapter.
Chapter 3 Router Configuration
ꢁ
This chapter describes the Galaxy router parameters configuration before putting it in service.
ꢃ
1. Connection
2. Configurations
ꢁ
Connect antenna properly before power on.
2.6 Check the Mobile Network
Thanks to the built-in web technology, Galaxy router can be easily configured
and managed. User may be required to configure associated parameters before
putting it in service. User can change settings and update firmware if it is
necessary.
Connect all signal and power cables, and double check it, connect antenna,
insert a valid SIM or UIM (depends your router type and network) and switch on
power. Galaxy H7920 router “RUN” LED will light up. If “RUN” LED is flashing, it
means the Galaxy is working normally. If the “LINK” LED is flashing, it means
there are data stream input/out over router data port. If the “NET” LED lights up,
it means that the Galaxy router has found and logged on mobile network.
By the Galaxy router management web pages, you can configure and manage
the router parameters. Refer to following description for details.
3.1 Connection
(More information refer to Chapter 4)
Normally, Galaxy router parameters should be configured through a PC. The PC
should meet the requirements:
ꢂ
ꢂ
Hardware
Software
PC with Ethernet interface, 1027x768 monitor
Windows 95/98/Me/NT/2000/XP operation system
IE 5.0 or up Internet browser
ꢁ
ꢁ
All cables should be connected correctly before switch on.
Antenna should be connected properly before switch on, otherwise it may
cause radio module problem.
ꢃ
Two suggestions you can select accordingly.
Direct Connection
Connect Galaxy router RJ45 interface with PC Ethernet interface by the supplied
CAT-5 UTP cable, and then set up the PC’s IP address/subnet to start the
configurations.
LAN Connection
It is possible to connect Galaxy router to a hub or switch port at your the LAN
environment. Therefore, any PC at the LAN can access the router and manage it.
M80-792001-01
M80-792001-01
13
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Your PC
Setup Correct Network Settings
You may be required to configure your PC IP address and associated parameters
after connecting the PC and router. You can set PC IP address “Obtain an IP
automatically” or set it manually. Refer to below descriptions for details.
Below is Galaxy router factory default setting; you can modify it accordingly.
IP Address: 192.168.8.1
Subnet: 255.255.255.0
Management Webpage IP address: 192.168.8.1
Login name: admin
Password: hongdian
ꢆ
The parameters in manual are Galaxy router default setting.
Pictures in this manual are captured at Windows XP and IE 6.0 platform.
Select “Internet Protocol (TCP/IP)”; click “Properties”.
Before Configuration – Setup your PC IP address
Double click “Network and Dial-up Connections” icon on the PC control panel,
you can find the Local Connection which is connected with Galaxy router (Direct
Connection) or the Local Connection that is connected with the LAN (LAN
connection).
Right click the “Local Area Connection” icon, select “Properties”.
M80-792001-01
M80-792001-01
15
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Here, you can select “Obtain an IP automatically” or “Use the following IP
address”. If Galaxy router is connected to your PC directly, it is possible to select
“Obtain an IP automatically”. Galaxy router built-in DHCP server will assign an IP
address to the connected PC. Sometimes, the PC may be required to restart.
The new add address should be limited at the subnet same as the Galaxy router,
i.e. 192.168.8.xxx (xxx is the number from 2 to 254). Subnet should be
255.255.255.0; and then click “Add (A)” button to add the address and subnet
into your PC. Your PC will be configured at the IP address “192.168.0.xxx” and
“192.168.8.xxx”. Click “OK” to complete configuration.
At LAN connection situation, the PC may be already assigned a LAN address
(Show as above picture). In order to keep this communication without any
interrupt, you can add a new IP address and subnet for Galaxy router
configuration. Click “Advanced (V)” button. (The “Default Gateway” is the access
to Internet for the PC. If you are not going to change the access to Internet, keep
the setting. If you are going to change the access to Internet via Galaxy router,
fill-in the router LAN address at “Default Gateway” setting, i.e. 192.168.8.1).
Before Configuration – Check your PC Settings
You can type “ping” command at DOS prompt to check the setting and
connection.
ping 192.168.8.1
If below information appears,
Pinging 192.168.8.1 with 32 bytes of data:
Reply from 192.168.8.1: bytes=32 time=2ms TTL=64
It indicates the connection between PC and Galaxy router is success; you can
start the configuration.
By typing “ipconfig” command at DOS prompt to check the IP address setting.
3.2 Configurations
Galaxy router can be managed via web interface or Console. The web interface
is an easy way to manage it. It will be described in details at following
paragraphs.
WEB Mode
With the built-in web server, Galaxy router can be easily managed via Internet
Explorer locally and remotely.
Click “Add” button at “IP Address (R)” item, fill-in the address which will add in
the PC.
Open IE on your PC, type a URL address.
The picture will appears.
M80-792001-01
M80-792001-01
17
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Main Menu
Router Status: Display major parameters
configuration and operation information.
Online Help: Provide online help.
System Tools: Provide a set of tools for the
router management, such as modifying
password, remote management, profile
backup, hardware & software information,
log and restart tool.
Network Setting: Provide LAN interface,
DHCP, mobile network parameters setting
and dynamic DNS configuration.
Route Configuration: Set up NAT, DMZ,
envelop filtering and the route paths.
Special Setting: Set up DTU parameters,
backup route paths.
Input user name: “admin” and password: “hongdian”
Hongdian Products: Browse Hongdian
Products catalogue.
It will display the main page “Welcome” if it is correct user name and password.
Click “Start” button to continue the management.
Logoff: Exit router management pages.
Notice:
Galaxy router should be configured properly; the “Network Setting” is the
basically and necessarily settings. We recommend customer should configure
this parameter first. Meanwhile, we suggest customer reads paragraph 3.2.4
before setting.
ꢆ
As mentioned before, the router configuration works should be performed via a
PC that is configured. The relative descriptions refer to paragraph 3.1.
Galaxy router factory default setting:
LAN IP Address:
Subnet:
Login Name:
Password:
192.168.8.1
255.255.255.0
admin
hongdian
You can modify above settings accordingly; and you may need to modify the PC
IP address settings if the router settings have been changed.
Click the “Start” button to display main menu.
Press and hold the “RESET” button for 5 seconds to restore the default setting.
Galaxy router is designed for industrial application and it works at
dial mode. However, at the beginning step, the router may not be
inserted a valid SIM/UIM card or configured incorrectly. The router
will try to dial and connect mobile network until establish the
communication channel. If it fails 3 tries, the router will restart
automatically. It will interrupt your configuration work. Therefore,
we recommend set dial mode to “Manual” by clicking
“Start”->“Network Setting”->“Network Basic Setting”.
M80-792001-01
M80-792001-01
19
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Console Mode
ꢂ
ꢂ
RF Signal: It displays Galaxy router received GPRS/EDGE or CDMA RF
signal strength in dBm unit. If the received RF signal is lower than
-80dBm, it displays the RF strength with "BAD" word.
Router ID: It is the router's unique identity name for industries and
utilities application. Click "Start">"Special Setting">"DTU Setting" to
modify it.
The Galaxy router RS-232 interface can configured for a data communication
port or a Console port. The Console port is only used for factory testing and
trouble shooting.
3.2.1 Router Status
"Data Traffic" displays Galaxy router inbound/outbound data packets and also
displays packets type and errors.
Click "Start"->"Router Status" menu, you will find Galaxy router operation main
information including settings and inbound/outbound data traffic.
Packets = Broadcasting Packets + Non-Broadcasting Packets + Loss + Error
ꢁ
Dial Info
Click this button to open detail dial info page:
Start module check.
Module checks OK.
Card ready.
CSQ: 026, 0.
Start dialing
Serial connection established.
Using channel 1
Using interface ppp0
Connect: ppp0 <--> /dev/ttyS1
Remote message:
Local IP address 10.103.32.97
(Note: assigned by mobile operator)
Remote IP address 192.168.100.101 (Note: it is the mobile network server
Thu Jan 18 00:00:30 2005
peer address)
It is a useful tool to check detail dial-up information. Select this option if the
router is unable to dial network, and send the dial-up information to Hongdian
for trouble shooting.
This page will display the information:
ꢂ
Mobile Network IP: It is an IP address assigned automatically by
GPRS/EDGE or CDMA 1x network. Normally, it is a dynamic IP
address unless it is bound with the SIM or UIM card.
Mobile Network IP: It is an IP address assigned automatically by
GPRS/EDGE or CDMA 1x network. Normally, it is a dynamic IP
address unless it is bound with the SIM or UIM card.
Mobile Network Subnet: It is a subnet assigned by GPRS/EDGE or
CDMA 1x network.
To have more dial-up information, tick the "Dialup Debug Info." at the page of
"PPP Advanced Setting".
(Access it by clicking "Start">"Network Setting">"Network Basic Setting", and
then click the “PPP Advanced Setting”)
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
3.2.2 Online Help
Peer to Peer IP: It is GPRS/EDGE or CDMA 1x network peer IP
address.
Click “Start”->"Online Help", a new windows will be opened, and the below
webpage picture appears.
DNS: It is setting parameters at the page DHCP Configuration. Access
it by clicking "Start">"Network Setting">"DHCP Configuration".
Access Point Name: It is APN parameters set at the page of Network
Setting. Access it by clicking "Start">"Network Setting">"Network
Setting".
ꢂ
PPP Status: It displays GPRS/EDGE or CDMA 1x connection online or
offline status and displays online period if the router is connecting
with network. For GPRS/EDGE version, since the clock is
synchronized to an Internet clock sources after connected to
GPRS/EDGE network. Therefore, the online period displayed on this
page may be not correct at the first dial-up.
M80-792001-01
M80-792001-01
21
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Router Administration
Click "Start"->"System Tools"->"Router Administration" menu to start this setup
page.
This is the detail operation instructions; all configuration and setting procedures
have been described in the Online Help file. Additionally, clicking the item “Online
Help” on the left of Help page, Galaxy router will connect to Hongdian website to
check updates.
ꢀ
Change Password
The system administrator login name: admin; default password: hongdian
3.2.3 System Tools
The default password should be modified and you need to input the original one
to modify it.
Click “Start”->"System Tools", the below picture will appear.
Press "RESET" button on router rear panel no less than five 5 seconds to reset
the password to factory default (hongdian).
ꢀ
Remote Configuration
GALAXY router is a web based controlling and management system. At normal
situation, operate it via LAN interface. Same as local LAN interface operations,
operator can certainly manage the router via mobile network at remote site.
For security reason, the default remote configuration function is disabled. It can
be enabled, and the access web port can be changed.
Type in Galaxy router connection URL at IE browser, then operator can remotely
manage Galaxy router. (It requires specifying the port if the webpage access
port is not 80. For example: http://220.192.11.22:8080)
When the webpage access port is changed, LAN side management webpage
access port is changed as well.
There are six sub-menus at "System Tools".
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Router Administration
Router Clock
Configuration Profiles
System Information
System Log
Router Clock
Click "Start"->"System Tools"->"Router Clock" menu to start this setup page.
Restart
M80-792001-01
M80-792001-01
23
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
With the built-in with real time clock function, GALAXY router will be
automatically synchronized with clock sources when it is powered on.
Press "Backup Configuration Profile" button to backup and store router
configuration profile in PC. Then, the original configurations stored in PC can be
retrieved. Press "Default Setting" button to restore router to default factory
setting.
For CDMA version, Galaxy router will be locked at CDAM network clock source.
For GPRS/EDGE version, Galaxy router will be synchronized to an Internet clock
source (NTP) when it has been connected to GPRS/EDGE network. There is an
option to enable or disable NTP client; and also the NTP server can be specified
accordingly.
System Information
Click "Start"->"System Tools"->"System Information" menu to start this page.
When the clock is synchronized to an Internet clock source, there is a drop list to
select the time zone accordingly. Also there is an option to enable or disable NTP
client; and also the NTP server can be specified accordingly.
Press "Synch" button to synchronize the router manually.
Once router restarts, the clock may be reset to the initial time and then
re-synchronize after the GPRS/EDGE network is connected.
Configuration Profile
Click "Start"->"System Tools"->"Configuration Profile" menu to start this setup
page.
There are reference information for router software upgrading and maintenance.
The page displays router type, hardware and software version, RF module type
and series number, router series number and so on.
M80-792001-01
M80-792001-01
25
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
System Log
Click "Start"->"System Tools"->"System Log" menu to start this page.
There are four sub-menus at "Network Setting".
ꢀ
ꢀ
ꢀ
ꢀ
Network Basic Setting
DHCP Configuration
SNMP Configuration
Dynamic DNS
Network Basic Setting
Click "Start"->"Network Setting"->"Network Basic Setting" menu to start this
setup page.
There are two options:
ꢂ
"Local Log": tick it on to log router operation information at router's
memory. Hongdian does not recommend ticking it on at the normal
operation.
ꢂ
"Remote Log": tick it on to send router operation information to a
specified IP host that runs a syslog daemon.
Press "Save" button to save the selections. Press "Clean" button to delete all logs
stored in Galaxy router.
Restart
Click "Start"->"System Tools"->"Restart" menu to restart Galaxy router.
3.2.4 Network Setting
Galaxy router should be configured with proper parameters. Network setting is
the basic and necessary configuration. Generally, LAN interface, mobile access
parameters and dial mode should be configured.
The router LAN interface, IP address and subnet can be modified if necessary. At
the initial phase, the PC that will connect to Galaxy router should be configured
as same as the router’s IP subnet (192.168.8.x/255.255.255.0, here x=2 to
254). For more information regarding the PC IP address setting, refer to this
manual Paragraph 3.1. Once your PC is set up properly, open IE browser and
input Galaxy router LAN IP address to start the configuration.
LAN Setting
There are three LAN IP addresses and subnets that can be utilized. However, the
host (or PC) that connect with Galaxy router should be configured at the same
subnet as one of the three LAN addresses setting.
First LAN IP address (default): 192.168.8.1, subnet: 255.255.255.0
It can be modified in accordance with the requirement.
Click “Start” > "Network Setting", the below picture will be displayed.
M80-792001-01
M80-792001-01
27
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Press "Save" button to store the modification.
ꢀ
W-ICMP Detecting
Reconnecting the host (or PC) after its IP address has been modified
successfully.
The WAN side IP link status detecting can be enabled or disabled. Also the
detecting interval (second), retries and destination (host) can be specified.
Mobile Network Configuration
The default setting is “disable” since this detecting packets may be charged.
Those parameters should be configured in accordance with the information
provide by the local service provider.
If it is enabled and fails the detecting at the specified interval, retries and
destination, the router will re-dial the radio link automatically.
ꢀ
Service Code
ꢀ
L-ICMP Detecting
It is the LAN side IP link status detecting, and it can be enabled or disabled. Also
the detecting interval (second), retries and destinations (host) can be specified.
Configure it with a correct service code provided by the service provider, the
default setting:
If it is enabled and fails the detecting at the specified interval, retries and
destination, the router will be restarted automatically. For this reason, the
destination at LAN side should be set correctly and keep it working properly.
Otherwise, it will cause the router restarting frequently.
ꢂ
ꢂ
GPRS/EDGE: *99***1# (for China Mobile)
CDMA 1x: #777 (for China Unicom)
ꢀ
User Name and Password
The default setting is “disable” since it may cause the router restarting.
Input a correct user name and password provides by local mobile service
provider; it will be required for dialing authentication:
ꢀ
IP Keeping
ꢂ
For China Mobile's GPRS CMNET user, no user name and password
required. APN user should input correct information provide by
service provider.
It keeps the IP link alive, and it can be enabled or disabled. The interval (second)
and destination (host IP address) can be configured.
ꢂ
For China Unicom's CDMA 1x user, user name is "card", password is
"card".
The default setting is “disable” since the IP Keeping packets may be charged.
ꢀ
PPP Advanced Setting
ꢀ
APN
Considering the difference of mobile network authorization, the Point to Point
Protocol connection should be compatible with different network. Advanced
setting is used for the PPP special setting. Click “PPP Advanced Setting” button to
start settings.
APN is the abbreviation of access point name; user should apply for it from the
service provider and then have it setup. For example, you can either input
“CMNET"/"CMWAP" for China Mobile or keep it in null. For other service
operators, please consult the local service provider.
ꢀ
Dial
It controls the RF module dialup mode; the default setting is "Auto".
When it is set to "Auto" mode, Galaxy router will automatically dial mobile
network and will re-dial if the mobile link fails. After 3 failed dialing, Galaxy router
will automatically restart RF module. When it is set to "Manual" mode, the timing
work mode for special setting may not be active.
ꢀ
PPP Detecting
It can be enabled or disabled. Also the detecting interval (second) and retries can
be specified accordingly.
The default setting is "Enable", "12" Second interval and "5" tries. With this
setting, the router will detect the PPP link status at 12 Seconds interval for 5
tries. If it is failed continually, the router will re-dial the radio link automatically.
When it fails redialing continually within 3 minutes, the router will be restarted.
M80-792001-01
M80-792001-01
29
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
ꢀ
Use Peer DNS
Normally, it is not required to change the setting for most of networks and
applications. If it is necessary, please consult with the local mobile operator and
try different settings.
It is the option to utilize mobile network gateway (GGSN or PDSN) DNS setting.
DHCP Configuration
ꢆ
DHCP means Dynamic Host Configuration Protocol. With the built-in DHCP server
at Galaxy router, it assigns IP addresses to the hosts that connect with the
network.
ꢀ
Dial Debug Info
Click "Start"->"Network Setting"->"DHCP Configuration" menu to start this
setup page.
It is a useful tool to check detail dial-up information. Select this option if the
router is unable to dial network, and send the dial-up information to Hongdian
for trouble shooting.
To enable the "Dialup Debug Info.", it will generate the log information of full
dialup progress.
ꢀ
MTU [
] Bytes
It is the data envelop package size transmitting to GGSN or PDSN during PPP
dialing.
ꢀ
MRU [
] Bytes
It is the data envelop package size receiving from GGSN or PDSN during PPP
dialing.
ꢀ
Set Local/Remote Interface IP
Specify local and remote IP address.
Local IP address is the Galaxy router IP address obtained from mobile network.
Remote IP address is GGSN or PDSN IP address.
There are following DHCP server settings.
ꢀ
Set Netmask
Specify the Netmask.
Auth
ꢂ
ꢂ
DHCP Server: Enable or Disable.
Start IP Address/End IP Address: Specify DHCP server IP address
range.
ꢂ
ꢂ
ꢂ
Subnet: Specify DHCP server subnet (subnet 255.255.255.0 suitable
for network within 256 hosts, 255.255.0.0 suitable for network within
65536 hosts).
Default Gateway: It is a gateway for hosts connected to Galaxy router
to communicate with outside network. You can setup its IP address
as necessary. Normally, it is Galaxy router LAN interface IP address.
Default DNS: Default main DNS, it should be configured with
information provide by the local operator. The default setting is
Shenzhen city DNS IP addresses.
ꢀ
ꢁ
ꢁ
Auto: Automatic authenticate with its protocol
Manual: Select MS-CHAP, MS-CHAP2, CHAP, PAP manually
ꢀ
PPP options
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
Disable Protocol Field Compress
Disable Address/Control Compress
Disable Compress Control Protocol
Disable the connection-ID Compress
Disable Van Jacobson Style TCP/IP Header Compress
ꢂ
ꢂ
Second DNS: Alternative DNS; it could be null.
Third DNS: Same as the above.
SNMP Configuration
Consulting with the local network operator and try those settings on order to
adapt mobile network.
Click "Start">"Network Setting">"SNMP Configuration" menu to this setup page:
M80-792001-01
M80-792001-01
31
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
ꢀ
SNMP: Enable or Disable, tick it to enable the SNMP function. It supports
SNMP V1 and V2C (V3 ready) automatically.
Before enabling the dynamic DNS function, you should apply a valid account
from a service provider in the drop list. Input the following information.
ꢀ
ꢀ
Set Community: Set the community name, such as "public".
IP: Set the SNMP management IP address. Usually, it is the router LAN
interface IP address.
System Name: Set the router name that will display on the NMS.
System Contact: Set the router contact name.
ꢂ
ꢂ
ꢂ
ꢂ
Service Provider
Host Name
User ID/E-Mail
Password/Key
ꢀ
ꢀ
ꢀ
System Location: Set the router location.
You can get the information from dynamic DNS service provider after successful
application.
It may be required to save all settings and restart the router to affect it.
Dynamic DNS service provider list will be added or deleted accordingly.
Dynamic DNS
As you know, there are many DNS server at Internet; it records and translates
the domain name into corresponding IP address. However, normal DNS server
only maps the domain name and static IP address.
3.2.5 Route Configuration
Click “Start” > "Route Configuration", the below picture will be displayed.
Dynamic DNS service will map the specified domain name to a dynamic IP
address. With the built-in client in Galaxy router, the dynamic IP address
assigned by mobile network and the domain name applied from dynamic DNS
service provider will be registered at Dynamic DNS server when the Galaxy
router is connected. Meanwhile, the built-in client will update the operation
information at the interval defined by the dynamic DNS server.
Click "Start"->"Network Setting"->"Dynamic DNS" menu to start this setup
page.
There are three sub-menus at "Route Configuration".
M80-792001-01
M80-792001-01
33
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
ꢀ
ꢀ
ꢀ
NAT/NAPT Configuration
Security Configuration
Routing Table
port has been mapped to a host at the LAN, the data at this port will be
transferred to this host, and not be transferred to the defined DMZ host.
Galaxy router can map up to 10 ports (hosts).
NAT/NAPT Configuration
Common used ports list:
NAT is the abbreviation of Network Address Translation. It maps the out side IP
address to a host or terminal in your LAN. It isolates unidentified data envelops
to guard the LAN against hacker’s attack.
Protocol
TCP
TCP
TCP
UDP
TCP
TCP
TCP
TCP
TCP
UDP
TCP
TCP
TCP
UDP
TCP
TCP
UDP
TCP
TCP
TCP
TCP
TCP
TCP
UDP
TCP
UDP
UDP
TCP
UDP
UDP
TCP
UDP
TCP
TCP
Service
AFP over TCP
AOL
Port
548
5190~5194
179
Click "Start"->"Route Configuration"->"NAT/NAPT Configuration" menu to start
this setup page.
BGP
DNS
53
FINGER
FTP
79
21
GOPHER
HTTP
70
80
HTTPS
IKE
443
500
POP3
110
PPTP
1723
7070
520
Real-Media
RIP
RLOGIN
SMTP
513
25
SNMP
161
IMAP
143
InterLocator
IRC
389
At default setting, the network behind Galaxy router is isolated from outside
network to provide safety for the hosts. For SOHO application, you may need to
setup your own WEB/FTP or other kinds of service; NAT (Network Address
Translation) /NAPT (Network Address Port Translation) technology can meet
your requirements.
6660~6669
1701
389
L2TP
LADP
NetMeeting
NFS
1503 & 1702
111
With this setting, the outer source ports can be mapped to a specified a host at
the LAN side. When the mapping scheme is defined, all the data traffic from/to
those mapped ports will be transferred to the specified host only.
NNTP
119
NTP
123
PC Anywhere
SSH
5631~5632
22
Above picture is an example.
SYSLOG
TALK
514
ꢂ
ꢂ
ꢂ
ꢂ
WEB Server: maps port 80 to a LAN host address 192.168.8.5
Voice Server: maps port 8000 to a LAN host address 192.168.8.10
Data Server: maps pot 5002 to a LAN host address 192.168.8.2
DMZ: maps the LAN host address 192.168.8.3 as DeMilitarized Zone.
517~518
23
TELNET
TFTP
69
The TCP, UDP or both protocols can be mapped to the destination ports. If the
destination port is not defined, it will be the same port as the source.
X-WINDOWS
WAIS
6000~6063
210
Additionally, there is a DMZ (DeMilitarized Zone) host that can be defined.
NAT/NAPT ports mapping is in higher priority than DMZ is. In other words, if a
M80-792001-01
M80-792001-01
35
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Security Configuration
For example:
With the security configuration function, you can control data envelops security
in/out your network. All outbound envelops are secured by this setting. Only
envelops to NAT or DMZ hosts toward inbound direction are secured.
4.3.2.1/32=one IP address only
4.3.2.1/24=a range IP address from 4.3.2.1 to 4.3.2.254
Click "Start"->"Route Configuration"->"Security Configuration" menu to start
this setup page.
For source and destination port, you can specify one port (i.e.: 80) or one range
(i.e.: 1000-1999) port. Meanwhile, it is possible to select the TCP and UDP
protocol individually or both of them. Null port setting means all ports.
If "ALL" or "ICMP" protocol option is selected, the port setting will not be active.
Save all the above settings.
Route Configuration
Click "Start"->"Route Configuration"->"Routing Table" menu to start this setup
page.
Selecting "Accept" or "Discard" action to protect the data envelops.
ꢁ
ꢁ
Accept: Accept data envelops that match settings only.
Discard: Discard all data envelops that match settings.
There are 10 policies can be defined. Also the inbound and outbound data
envelops can be controlled.
For each policy, there are following items can be defined.
ꢁ
ꢁ
Protocol: TCP, UDP, ICMP or All selectable.
Source IP address/Subnet: Define source data envelops IP address and
subnet.
Routing table defines IP data packages transfer paths. If there are more subnets
and routers in the network, you have to define the correct data transmission
paths to ensure that the data packages can be exchanged between subnets.
ꢁ
ꢁ
Source port: Define source data envelops port.
Destination IP address/Subnet: Define destination data envelops IP
address and subnet.
There are 10 routing policies can be defined for Galaxy router. Each of source IP
address, subnet and gateway should be specified.
ꢁ
Destination port: Define destination data envelops port.
It is possible to define the source and destination IP address with a subnet.
Therefore, one IP address (i.e.: 4.3.2.1) or one range (i.e.: 4.3.2.1~4.3.2.254)
IP address can be defined accordingly. Null subnet setting means all IP address.
The subnet is described by a decimal number 8, 16, 24 or 32.
8=255.0.0.0, 16=255.255.0.0, 24=255.255.255.0, 32=255.255.255.255
M80-792001-01
M80-792001-01
37
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
For Example:
3.2.6 Special Setting
Galaxy router is not only integrated with router functionality, but also can be
configured for many other applications. The Special Setting function is designed
for industries and utilities. Several parameters can be configured accordingly.
With the Special Setting, a non IP based device (such as RS-232 interface POS)
data can be transmitted over Internet. There are many applications of center to
multi-point infrastructure, such as video surveillance system and SCADA system,
etc.
The Special Setting is designed for industrial application. It is not necessary to
set up special parameters if you are planning to use only route features, and the
default setting is “Disable”. The Data Service Center and associated parameters
should be configured properly if the Galaxy router is used for remote
management and surveillance.
ꢆ
Click “Start”->"Special Setting", the below picture will be displayed.
Network
192.168.2.33
192.168.2.55
192.168.2.11
192.168.8.1
192.168.3.1
192.168.5.1
192.168.8.22
192.168.3.44
192.168.5.66
There are four sub-menus in "Special Setting".
ꢀ
ꢀ
ꢀ
ꢀ
DTU Setting
Serial Port Setting
Operation Mode
Backup Routing
With the route policy showing above picture, the data envelops must be
transferred by gateway (192.168.2.33) if the transmitting data envelops are
from host 192.168.8.22 to 192.168.3.44.
DTU Setting
Click "Start"->"Special Setting"->"DTU Setting" menu to start this setup page.
Similarly, the data must be transferred by the gateway (192.168.2.55) if the
transmitting data envelops are from host 192.168.8.22 to 192.168.5.66.
Save the settings when it is completed.
Note: The IP addresses on the picture are not the real addresses; it is used for
description only. Additionally, gateway IP address should be a static IP address
at real engineering.
M80-792001-01
M80-792001-01
39
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
For many applications, it requires to keep the links always online. The heartbeat
setting should be set to keep the links alive. However, the heartbeat is the data
traffic packets and it may be charged (depends service provider). You have to set
a right heartbeat interval in accordance with application. Normally, we suggest
the 50 seconds heartbeat interval for most of applications.
ꢀ
Router ID
It is the router unique identity name at data service center. By the unique ID, you
can transmit/receive data to/from remote site and also manage remote router.
Set it according to the application system planning.
Serial Port Setting
Galaxy router can be used to connect non-IP based data terminal such as POS,
RTU and PC Hypertext Terminal. The serial port should be configured properly
before putting it in service.
Click "Start"->"Special Setting"->"Serial Port Setting" menu to start this setup
page.
ꢀ
Data Service Center (DSC)
DSC can be enabled or disabled. Default setting is "Enable".
Type of Service
There are two options:
ꢀ
ꢂ
ꢂ
Client: The Galaxy router will act a client function to send data to the
specified DSC.
Server: The Galaxy router will act a server to listen the data transfer
from the specified DSC.
ꢀ
Protocol
There are TCP and UDP options for selection. Based on past experience,
GPRS/EDGE or CDMA 1x channel is not reliable due to radio propagation. UDP is
recommended for transmitting real time information with data checksum, such
as SCADA system. TCP protocol may be better for transmitting files.
ꢀ
DSC IP Address or Domain
ꢀ
Serial Port
Data Service Center (DSC) IP Address or Domain is the server address that
receives data from serial port device connecting with Galaxy router. It supports
IP address or domain name.
There are "Enable" and "Disable" switches.
Default setting: Disable.
ꢀ
DSC Port
If the serial port is enabled, the DSC IP address or domain name must be
specified.
Defining Data Service Center communication port, it can be changed with the
system planning. The default port is 5002.
ꢀ
Interface
ꢀ
Heartbeat Interval
Select serial port interface type: RS-232 or RS-485; RS-485 is not available at this
version hardware.
M80-792001-01
M80-792001-01
41
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
ꢂ
ꢂ
Operation Mode: Enable or disable.
Timing: Specified the online time and offline time, press ADD button
to add the timing plan to the time schedule.
ꢀ
Rate
Setup serial port interface data rate:
300/600/1200/2400/4800/9600/19200/38400/57600/115200(BPS)
ꢂ
Schedule: Display the specified time schedule. Select a timing plan
and press DEL button to delete it.
ꢀ
Parity
Select parity: None/Odd/Even
Data Bits
Setup data bits: 5/6/7/8bits
Stop Bits
Setup stop bits: 1 or 2bits
Flow
Note:
1. If the time plan covers two days, it will separate into two timing plans at the
time schedule, i.e.:
ꢆ
ꢀ
Set the time from 23:00:00 to next 05:00:00,
it will separate into 23:00:00~23:59:59 and 00:00:00~05:00:00
2. The router clock should be enabled if the timing mode is enabled.
ꢀ
Backup Routing
For many applications, customer may require backup routings to protect their
communication. There are two backup channel can be set up, customer can set
the GPRS/EDGE/CDMA 1x channel as the main channel, and set the Ethernet or
dial-up channel as the backup route.
ꢀ
Setup flow control: None/Hardware/Software (Xon/Xoff)
Operation Mode
Click "Start">"Special Setting">"Backup Routing" menu to start this setup page.
For industrial applications, requirements may be different from customer to
customer. There are five modes available in Chinese market. Presently, there is
only one timing mode in English version available. Hongdian can design new
customized operation modes for any other market.
Click "Start"->"Special Setting"->"Operation Modes" menu to start this setup
page.
This function can be "Enable" or "Disable".
When it is enabled, the "W-ICMP detecting" at the "Network Basic Setting" page
will not effect.
ꢀ
Default Route: Select Galaxy router default routing, it is the main route.
There are three types of route can be selected: Radio, Ethernet and COM
(connecting with a dial-up modem). When Ethernet or COM is set as default,
the Radio will be the backup.
Timing operation mode can be configured:
M80-792001-01
M80-792001-01
43
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
ꢀ
Route Detecting: Detecting the destination host IP address, if there is no
response at the set time interval and times, the router will switch over to the
selected backup route.
Click the "COM Port Setting" button to this setup page.
ꢂ
When the "Radio" is set to the default route and the backup routing
function is enabled, we recommend setting the operator's gateway as
the destination IP address for detecting.
ꢂ
When the "Ethernet" or "COM" is set to the default route, we
recommend setting a reliable host in the Internet as the destination IP
address. Meanwhile, set the “Back Time” to force the backup route to
be switched back the default route.
Attention: The destination host should work reliable. Otherwise, it will cause the
router switch over frequently.
ꢀ
Backup route: There are two options.
ꢂ
ꢂ
Gateway - When the "Enable Gateway" is enabled, the traffic will be
routed to this gateway via the Ethernet interface if the default route
failed. The gateway IP address is the network gateway IP address that
Galaxy router is connected.
COM - When the "COM" port is enabled, the traffic will be routed to
Galaxy router COM port if the default route failed, and then the
connected modem will dial a number that specified at COM port setting.
At this page, set up the COM port interface and the dialup parameters. Because
of the COM port may be connected with different types of modem, it provides a
script filed to fill-out the dial-up number and modem initialization strings (AT
command) in accordance with the associated modem.
ꢀ
COM Port Setting:
Before enabling this function, it is required to connect a dial-up modem (i.e. V.90
modem) to the Galaxy router’s COM interface. A special cable will be needed.
The cable wiring is showed at the below diagram.
For example, dial a number 83890677, fill in the below code at the “Dial Script”
filed.
-----------------------------
"" at
OK atxxx
OK atd83890677
TIMEOUT 30
CONNECT ""
-----------------------------
RS-232 Modem
atxxx is the modem extra command that may be used (depends on the
connected modem). It should be filled in with the connected modem parameter.
RS-232 DB9 (Male)
RS-232 DB9 (Male)
All extra AT commands should be added before dialing. In other words, all extra
AT commands should be added before the atd command.
CD
RX
1
2
3
4
5
6
7
8
9
1 CD
2 RX
3 TX
4 DTR
5 GND
6 DSR
7 RTS
8 CTS
9 RING
If the telephone line is behind a PABX, it may be needed to dial a "0" and waiting
the dial tone. The atd command should be:
TX
DTR
GND
DSR
RTS
CTS
RING
atd0,83890677
The COM port will try to dial the backup channel. If it fails the connection for 3
times, the router will switch back to the default routing and try another
sequence.
The route status will be displayed on the front panel LED.
M80-792001-01
M80-792001-01
45
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
Galaxy H7920 Mobile Router User Manual
Chapter 3: Router Configuration
ꢂ
ꢂ
RUN LED, blinking in 1 second interval; it indicates Galaxy router
works at default route (main route).
RUN LED, blinking in 2 second interval; it indicates Galaxy router
works at backup route.
TFTP update
H7920 is built-in with a tftp client. Operator can update the firmware via a TFTP
sever. The latest version H7920 firmware has the tftp feature included.
3.2.7 Hongdian Products
Download the tftp server at:
Click "Start"->"Hongdian Products" menu, it displays more Hongdian products.
For more information, click the links listed at this page.
Start the tftp server at your PC, and copy the updated firmware at the same
folder of your tftp server.
telnet and login H7920 router
tftp ipaddr
(The ipaddr is the tftp server IP address.)
get filename
(The filrname is the firmware filename; it should be copied at the same
folder of your tftp server.)
It will transfer the firmware to H7920 router’s RAM, and follow the prompt to
save it into flash.
Save to flash? Press Y to save it.
Restart the router to affect the update.
Attention!!! during the saving, please do not drop the H7920 power supply.
3.2.8 Logoff
Click "Start"->"Logoff" menu to exit router configuration & management pages.
ꢃ
You may be required to enter correct user name and password when you
re-login.
Hongdian Update Tool
The update tool instructions refer to Appendix 2.
3.2.9 Firmware Update
3.3 CLI Operation
Galaxy router is capable to update by a special update tool. You can download
the update tools and associate firmware at Hongdian website.
GALAXY H7920 supports CLI operation, by using the telnet command to operate
it. For example:
Visit Hongdian website at "Support"->"Software Update" section for full details;
or Enter Galaxy router's "Online Help" page, click "Online Help" item to check
updates.
telnet 192.168.8.1
(follow the prompt to type user name and password, it is the system
administrator’s user name and password.)
/>cli
CLI>
There are two ways to update the router firmware:
Type ? or help to display the command help, type any word that does not match
commands, it will display help contents also.
ꢂ
ꢂ
TFTP
Hongdian Update tool
Contact Hongdian Technical support department for detail operation manual.
M80-792001-01
M80-792001-01
47
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 4: Operation Instruction
Galaxy H7920 Mobile Router User Manual
Chapter 4: Operation Instruction
Chapter 4 Operation Instruction
4.2 Operation
This chapter introduces Galaxy H7920 router operation introductions.
Galaxy router is an embedded hardware and software platform. Normally, it is
working without any manual operation. It provides a reliable and flexible data
channel for industrial applications.
1. Panel Indication
2. Operation
3. Trouble Shooting
Galaxy router should be installed at place with good radio signal receiving. For
the cabinet and basement environment, we recommend to extend the antenna.
4.1 Panel Indication
For outdoor use, lightning should be considered. We propose to install an
arrester between antenna and the ANT interface. Contact Hongdian technical
support department for details.
There are four LEDs at Galaxy H7920 router front panel; it indicates the router
and network operation status.
ꢃ
LED
10M
Status
Description
Blinking (data detected) Connected 10BaseT device and data
transmission detected
Lights off
Lights up
Lights up/Blinking
Lights up
Blinking (1/2 second)
Blinking (1 second)
Blinking (2 second)
4.3 Trouble Shooting
Connected 100BaseT device
Ethernet connected
Depends network & radio module (*)
Router self test and initializing
Router dialing
LINK
NET
RUN
Problem 1: All LEDs are not lights-up.
Check all cables that are connected to the router.
Check the power supply adapter output voltage.
Normal operation (default route)
Normal operation (backup route)
If the power is correct and there is no LED lights-up, the router may be
failed. Contact to Hongdian or reseller for repairing.
(*) NET indication will depend on the type of radio module and network. The
detail information will be updated on website. Click “Start”->“Online Help” at
Galaxy router menu, and then click “Online Help”->“FAQ” at the help page for
details.
Problem 2: Router works not stable after long time operation.
Check router cabinet temperature, if it is overheating, place the router at the
place with good ventilation.
Refer below table for H7920-RGH and H7920-RGM2 NET LED indication
descriptions:
Problem 3: Router does not run self-test when it is powered on.
Check the power adapter.
H7920-RGH
NET LED
Lights up
Lights off
Blinking (1 second)
Blinking(1/4 second)
Lights up
Description
Note
Radio Module Starting
No Power or sleeping (deeply)
No SIM card or searching GSM network
GPRS data transmitting
Calling
Problem 3: Update failed
System boot system and application program are stored at different memory
allocation; failed update will not affect the router rebooting. Re-update the
firmware until it is working.
H7920-RGM2
NET LED
Problem 5: time out when ping the router.
Description
Note
Lights up
Lights off
Logon GSM and normal operation
No Power or out of GSM service
Pinging 192.168.8.1 with 32 bytes of date:
Request timed out.
It indicates that is something wrong during the installation, check following
items:
ꢂ
Check the Ethernet connection between your PC and Galaxy router.
M80-792001-01
M80-792001-01
49
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Chapter 4: Operation Instruction
Galaxy H7920 Mobile Router User Manual
Appendix 1: Hypertext Terminal Setting
(Note: Galaxy router’s LINK and PC’s Link should lights-up if it is
connection).
Check your TCP/IP setting.
ꢂ
Appendix 1: Hypertext Terminal Setting
(Note: If the Galaxy router LAN IP is 192.168.8.1, your PC local
connection IP address should be 192.168.8.xxx).
This Appendix introduces Microsoft Windows HyperTerminal setup instruction.
For more checking, type “ipconfig” command at DOS prompt.
1. COM Port Setting
2. Properties
3. Codec Setting
4. ASCII Code
1. COM Port Setting
By Clicking Windows “Accessories”->”Communications”->”HyperTerminal” to
create a HyperTerminal. Refer to below picture to continue the settings.
(Type “ipconfig ?” Command for its help)
M80-792001-01
M80-792001-01
51
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Appendix 1: Hypertext Terminal Setting
Galaxy H7920 Mobile Router User Manual
Appendix 1: Hypertext Terminal Setting
The COM port parameters should be specified. Select COM number (i.e. COM2),
Bites per second, Data bits, Parity, Stop bits and Flow control.
3. Host System Encoding Method
Click “Input Translation” button, set host system encoding method.
Notice: “Flow control” should be set to “None”.
ꢆ
2. Properties
Start the created H7000 HyperTerminal connection. Click “File”->“Properties”
menu, click “Settings” tab, set it as show as the picture.
M80-792001-01
M80-792001-01
53
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Appendix 1: Hypertext Terminal Setting
Galaxy H7920 Mobile Router User Manual
Appendix 2: Firmware Update Tool
4. ASCII Setup
Appendix 2: Firmware Update Tool
Click “ASCII Setup” button, set ASCII parameters.
This appendix describes Galaxy router firmware update tool user instructions.
Galaxy H7920 Firmware Update Tool
Set up the PC IP address subnet same as the router that will be updated.
Copy the Router Update Tool to the PC and run it (Fig. 1):
Fig. 1
Click “Browse” button to retrieve the .rom file (Fig. 2)
Fig. 2
Input Router IP, factory default IP is 192.168.8.1; the Router IP could be the LAN
IP or WAN IP address (WAN IP is the address assigned by service provider
gateway; normally it is a dynamic address). Type the correct password (this is
the password you access router configuration web interface; factory default is
hongdian). Press “Connect” button (Fig. 3), and waiting few seconds. If dialogue
info appears (Fig. 4), it means the connection failed. Otherwise, it is successfully
connected.
M80-792001-01
M80-792001-01
55
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy H7920 Mobile Router User Manual
Appendix 2: Firmware Update Tool
Galaxy H7920 Mobile Router User Manual
Appendix 2: Firmware Update Tool
Warning
1. Do not disconnect or power off the router during firmware updating.
2. Mobile network may be failed sometimes; it is a high risk to update firmware
remotely.
ꢃ
Fig. 3
Fig. 4
Press “Update” button to update the router firmware (Fig. 5)
Fig. 5
Fig. 6
Waiting about 20 seconds, “Update success” info will appear. It means the router
has been update successfully, otherwise it fails.
Note: If you can not open the Galaxy router webpage after updating software,
reconnect your PC local connection.
M80-792001-01
M80-792001-01
57
58
Download from Www.Somanuals.com. All Manuals Search And Download.
|