DUAL SATELLITE
INSTALLATION MANUAL
SAC-00-094
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Getting Started
This Shaw Direct Installation Manual provides all the
information you require to install your system. The
instructions are fairly simple, providing step-by-step
instruction for system installation. However, it will
require skills in construction, wiring and assembly to
correctly complete the installation.
Quad LNB
Important: We also recommend against installing the
satellite dish on your roof, unless absolutely
necessary. If you do choose to mount the dish on the
roof, we strongly recommend consulting with a
building or construction expert before installation.
Elliptical Dish
IMPORTANT: Read this manual thoroughly before
beginning installation.
Universal
Mount
Assembly
Clamp
Mount
Assembly
Satellite
Feed
Support
Arm
WARNING: All satellite dish systems must be
properly grounded, particularly if the dish is close to
or above the roof line. Improper grounding can result
in damage or serious personal injury. National,
provincial and local electrical codes may require you
to ground the dish directly and to insert a grounding
block in the coaxial cables running from the dish to
the receiver inside the building. Before beginning
installation, carefully read the section on grounding
the dish (see section 11).
Hardware
1/4" External Tooth Washer
2 Supplied
1/4"x 1-1/2" Long Hex Head Bolt
This installation requires you to:
(Feed Support Arm Mounting)
1 Supplied
• Use hand tools such as a hand drill
• Determine whether water pipes, electrical wiring or
gas lines are close to the installation area
• Route coaxial cable through walls and
under floors
1/4" Whiz Nut (Hex Head)
5 Supplied
1/4" x 1-3/4" Long Carriage Head Bolt
(Antenna Mounting Bolt - Painted Head)
2 Supplied
• Use a compass, protractor and carpenter’s level
• Use a ladder to climb structures
• Know your local, provincial and national grounding codes
Spacer Sleeve
(Feed Support Arm Mounting)
1 Supplied
If you feel you do not have the experience to perform
these tasks, contact Shaw Direct at 1.888.554.7827 for
assistance.
1/4" x 1/2" Carriage Head Bolt
2 Supplied (Mast Adjusting Bolts)
You’ll need the following tools:
• #1 Philips Screwdriver
• 7/16 Hex Wrench, open or combination end
• Electric Drill and Bits
• Carpenter’s Level
1/4" Flat Washer
3 Supplied
Hex Head Hi/Lo Screw
2 Supplied
• Compass
• Protractor
Your satellite Shaw Direct Dish Kit contains the
following components:
• Shaw Direct Elliptical Dish with dual satellite
hardware
3
SAC-00-094
Download from Www.Somanuals.com. All Manuals Search And Download.
Key points to remember when installing your
Shaw Direct System:
• If you install the dish on the roof or side of your
house, be sure to attach the bolts into a building stud,
rafter or other solid surface.
• When mounting on the roof of your house,
use an adequate/approved sealant (for your type of
roofing material) around the holes where the base of
the universal mount meets the mounting surface. This
will prevent the roof from leaking. (Consult with a
roofing expert to confirm best sealant.)
• Do not drill any holes until you’ve confirmed the
best location for the dish.
• Make sure the installation of the dish conforms to
local electrical and building codes, zoning requirements
and other applicable laws and regulations. If you are
unsure, contact your local electrician or building
inspector for assistance.
• For possible periodic removal of snow, choose a site
that is easily accessible.
• We do not recommend:
• Mounting the dish on a railing
• Installing the dish on aluminum or vinyl siding
(these are unlikely to be structurally sound)
• Keep grounding requirements in mind (see section 11
for additional information on grounding).
• Ensure there are no visible obstructions between the dish
and your line of sight to the satellites. Keep in mind that
trees will grow up and outward and may eventually block
the signal.
• The maximum allowable length for the RG-6 coaxial
cable connecting the receiver to your dish is 125 feet.
Consult Shaw Direct if the cable will exceed this length.
3. Dish Assembly
Step 1: To avoid losing any hardware components, select
• Use only RG-6 grade coaxial cable. Using lower grade
RG-59 coaxial cable may result in excessive signal loss
and poor reception. Cable grade type is indicated on the
outer jacket of the cable.
a clear area on the ground for dish assembly.
Step 2: On the Universal Mount, insert the (2) 1/4" X 1/2"
Carriage Head Bolts (Mast Adjusting Bolts), through the
mast and the curved slot of the mount. Capture with
(2) 1/4" External Tooth Washers and (2) 1/4" Whiz Nuts.
Tighten the bolts just enough to hold in place (see
Figure A).
• Do not install the dish:
• Under power lines
• Where it may be easily tampered with
• Where it is exposed to high winds, during windy or
stormy conditions
Shaw Direct offers a supplementary Self Install Kit, If you
have not already purchased our Self Install Kit, you may
do so by calling 1.888.554.7827. This kit contains
everything you will need to successfully install your Shaw
Direct satellite system. Please contact Shaw Direct to
order or receive additional information regarding the Self
Install Kit.
Fig. A
2. Mounting Locations
Your dish will typically be mounted on a solid base. To
ensure your dish doesn’t move in windy conditions, choose
a location where it can be securely fastened. The mounting
surface should be rigid and solid.
IMPORTANT: The Elliptical Dish has a turn radius of
+/ 35 degrees. If you are mounting the dish on the
side of your house, check the assembled dish and
mounting pole to see if you can rotate the dish in
the desired azimuth setting. If you can’t rotate the
dish, choose an alternate location.
Step 3: Attach the dish to the Clamp Mount Assembly
using the (2) 1/4" X 1-3/4" Long Carriage Head Bolts
(Antenna Mounting Bolts-Painted Head), (2) 1/4 Flat
Washers and (2) 1/4" Whiz Nuts. Ensure the Center Pivot
Pin on the Clamp Mount Assembly is inserted in the
mating hole of the Dish (see Figure B).
_
Key things to remember when choosing a mounting
location:
Note: We do not recommend mounting the dish on
the roof unless absolutely necessary. We also
recommend that you consult a building expert for
future tips on preventing roof leakage.
• The mounting surface should be flat, even and in good
condition.
4
SAC-00-094
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. B
4. Locating the Satellite
Step 1: Determine the direction in which to point the dish.
The primary satellite SAT A is located at 107.3 west
longitude; the secondary satellite (SAT B) will be located
at 111.1 west longitude.
1/4" x 1-3/4" Long
Carriage Head Bolt
(Antenna Mounting Bolt)
Clamp Mount
Assembly
1/4" Flat Washer
IMPORTANT: For dual satellite dish installation, use
the SAT B Azimuth, Elevation and Skew listings in the
Dual Satellite Locator Chart at the back of this
manual for the city nearest your location to point the
dish in the general direction of the Anik satellites.
1/4" Whiz Nut
1
0
2
0
0
6
40
Center Pivot Pin
Dish
Socket
Write them here:
Azimuth
Before tightening the bolts, adjust the skew alignment to the
90 degree mark on the Clamp Mount Assembly (see Figure C).
Tighten the bolts just enough to hold in place. You’ll have to
make further adjustments to this setting later.
Elevation
Skew
SAT A:__________ SAT A:__________ SAT A:________
SAT B:__________ SAT B:__________ SAT B:________
TIP: Initially setting the skew to 90 degrees will make it
easier to aim the dish.
Fig. E
Azimuth Clamp Bolts
Fig. C
Boss Holes
Skew Alignment
Mark
Skew Adjustment
Nuts
Azimuth
Elevation
Skew
NOTE: Each Scale
mark is 2 degrees
Step 2: Use a compass to determine roughly where to
point your dish.
Step 5: Attach the Feed Support Arm to the dish using
the (1) 1/4" X 1-1/2" Hex Head Bolt (1), Spacer Sleeve, (1)
1/4" Flat Washer and (1) 1/4" Whiz Nut, making sure the
Feed Support Arm and Spacer Sleeve are positioned as
shown in Figure D. Position the 2 plastic cable clips
packaged with the LNB around support arm to secure the
coax cable(s) from the LNB to receiver.
Step 3: Choose a dish installation location with a clear
line of sight to both SAT B and SAT A based on the
settings you recorded earlier. There should be no trees,
buildings or other obstructions between the dish and the
satellite. Do you have a clear line of sight to both SAT A
and SAT B?
• If YES, go to Step 4 and continue with the
installation.
Fig. D
• If NO, find another location.
• If you’re not sure, contact Shaw Direct for more
information.
NOTE: To ensure an accurate compass reading, stay away
from large metal objects. To double-check accuracy, take
multiple readings several feet apart.
Dish
Socket
1/4" Whiz Nut
Step 4: At the dish install site, hold a compass level and
still in the palm of your hand. When the needle stops
rotating (dark half of the needle always points north),
slowly rotate the body of the compass so that the "N"
marking is aligned with the dark half of the needle.
Locate the tick mark on the compass edge corresponding
to the SAT B azimuth number you wrote down earlier
(see Figure F). This is the direction in which to point your
dish to receive both SAT A and SAT B signals.
Spacer
Sleeve
Flat
1/4" Washer
Feed
Support Arm
1/4" x 1-1/2" Long
Hex Head Bolt
ꢀ
You’ve just finished assembling the dish.
TIP: Use a stick or other object to mark the correct
azimuth direction.
5
SAC-00-094
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. F
Fig. F
Level Not Level
Fig. H
Fig. H
If you live in
Vancouver,
the satellite will be
to the Southeast
Use bubble level
to plumb mast so
it is vertical in all
directions
If you live in Newfoundland,
the satellite will be
to the Southwest
Curved
slot
Step 5: Estimate the SAT B elevation (angle) setting you
recorded earlier, using a protractor if needed (see Figure
G). Check any obstructions at that elevation. If there are
obstructions, then select an alternate location for the dish.
Step 2: Drill holes in the structure on which you are
mounting the dish to match the holes in the base of the
Universal Mount.
90°
60°
30°
Fig. G
Fig. G
Step 3: Secure the Universal Mount with appropriate
surface screws. Check the mount for movement. An
improperly secured mount will affect dish performance.
0°
Step 4: Slide the Dish/Clamp Mount Assembly onto the
mast by loosening the (2) Azimuth Clamp Bolts (see
Figure C) and the Elevation Pivot Bolt just enough to
slide the assembly until it makes contact with the
Elevation Pivot Bolt (see Figure I). Tighten the Elevation
Pivot Bolt just enough to hold it in place on the mast.
0 degrees is straight toward the horizon and 90 degrees is straight upward.
IMPORTANT: When evaluating the install location,
make sure there are no trees, branches or objects
visually obstructing the dish and the general
direction of the satellite. Also, keep in mind that trees
grow up and outward and may eventually block the
signal.
When Adjusting
elevation use edge of metal
to line up with elevation setting
for your area on the elevation scale.
Fig. I
ꢀ
You have just completed locating a site for your dish.
Use the metal edge,
not the nut or L-Bracket to
Elevation
Pivot Bolt
5. Attaching the Dish
set the elevation. (For example,
in this picture, the elevation
is set at 26).
Elevation
Adjustment Bolt
Step 1: Ensure mast is plumb before drilling any holes.
Hold the Universal Mount in place on the mounting area.
Use a carpenter’s level to plumb the antenna mast’s
straight section. If the bubble levels (horizontal and
vertical) are not centered, rotate the mast (in the curved
slot) until it is plumb. Then lock it in place by securely
tightening the Mast Adjusting Bolts (see Figure H).
Elevation
Indicator
Step 5: Loosen the Elevation Adjustment Bolt 1/3 turn
from tight on either side of the Clamp Mount Assembly.
Adjust the Clamp Mount Assembly to the edge of the
white indicator line per the SAT B elevation setting you
recorded earlier. Tighten the Elevation Adjustment
Bolt (see Figure I).
IMPORTANT: Alignment of the dish will be difficult
if the mast is not plumb.
6
SAC-00-094
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 6: Attach the Quad Satellite LNB/Feedhorn Clamp
Assembly to the Feed Support Arm. Loosen the Feed Arm
screw enough to allow the clamp to fit snugly into the
require an assistant to monitor the signal level reading on
the TV as you align the dish for maximum signal.
2. When receiver is first powered up, if receiver is tuned to
channel 255 (factory default channel on receiver models
DSR205 and DSR315), set receiver to channel 284 prior to
starting dish alignment. Otherwise, if receiver is set to
channel 299 (factory default channel for new DSR5xx series,
DSR207/209, DSR317/319), change channel to 299 prior to
starting dish alignment.
Feed Support Arm. Securely tighten the Feed Arm screw.
Step 7: Using your compass, point the LNB in the direction
SAT B
corresponding to the
azimuth setting (see Figure M).
Draw a vertical mark overlapping the Clamp Mount
Assembly and the mast. This mark will provide you with the
approximate satellite location reference point when you’re
ready to tune to the satellite.
For DSR205 and DSR315 receivers you should see the
following displayed on the TV when you first turn receiver
on. Using remote tune receiver to ch 284 to align the dish.
Fig. M
For new DSR505, DSR530, DSR207/209 and DSR317/319
you should see the following displayed on your TV when
you first turn receiver on. Receiver should be tuned to
channel 299.
Step 8: Loosen the Skew Adjustment Bolts on either side of
the Clamp Mount Assembly. Adjust the Skew Alignment
Mark with the scale indicator to the SAT B skew setting you
recorded earlier. Finally, lock it in place by securely
tightening the Skew Adjustment Bolts.
IMPORTANT: Do not make any further adjustments to
the Skew Setting from this point onward.
Step 9: After making the permanent skew adjustment, install
the (2) Hex Head Hi/Lo Screws in the dish boss holes (see
Figure C). Four boss holes are available but you’ll only need
to use two (the other two may be obstructed depending on
the skew setting). Do not over tighten Hi/Lo Screws.
3. Once dish has been connected to the receiver and
receiver connected to the TV, follow the steps in the
Motorola User Guide to access the installer menu.
ꢀ You have just finished attaching the Dish to the
Universal Mount.
To access this menu for DSR205 and DSR315 model
receivers, using remote
6. Connecting
Receiver and Dish
1. Press Options,
2. Press 6 System Setup
3. Press 3 Installation settings
4. Press 1 Tune in Satellite Signal
You are now at the point in the installation where one of the
output ports of the QUAD LNBF needs to be connected to
the satellite input connector of the Motorola DSR satellite
receiver. Refer to the Installation Section of the Motorola
User Guide and follow the instructions on how to connect
the cable from the satellite dish to the satellite input
terminal on the satellite receiver’s back panel and how to
connect the satellite receiver to your TV set. To view the
receiver’s installer menu you must connect the receiver to a
TV set to show you a relative scaled signal level meter that
will assist you to align the dish to maximum signal strength
for your location.
1. Connect the coaxial RG6U cable provided with the install
kit to one of the ports of the QUAD LNBF and connect the
other end of the coaxial cable to the satellite receiver input
connector. To make the dish alignment easier, suggest you
locate receiver and TV at an electrical outlet close to where
the dish is installed. Unless you can view the signal level on
the TV screen from where the dish is being aligned, you will
Installer Menu for Motorola DSR205, DSR315 and
DSR405 model series receiver.
7
SAC-00-094
Download from Www.Somanuals.com. All Manuals Search And Download.
Position yellow cursor (using navigator keys on the remote
control) on the Provider ID and enter 4128 from the keypad
4. Draw a reference mark on the dish clamp and pipe
mast as a starting point before you make any
adjustments to the dish.
To access this menu for DSR5xx, DSR207/209 and
DSR317/319 model receivers, using remote
5. Standing behind the dish, using both hands, grab the
dish on each side and slowing move dish in very small
increments to the east (or west) several degrees while
your assistant observes the TV installation menu for
increase in signal strength.
1. Press Options,
2. Press 6 System Setup
3. Press 4 System Settings
3. Press 3 Insatllation Settings
4. Press 1 Tune in Satellite Signal
6. As you start to get indication of increasing signal make a
second reference mark on the dish clamp and pipe mast to
serve as a point where signal strength increased.
7. As you move dish past the point of maximum signal
strength, move dish back in the opposite direction until you
achieve maximum signal.
Installer menu for DSR5xx, DSR207/209 and DSR317/319
model series receiver.
Position yellow cusor (using navigator keys on the remote
control) on EMM Provider ID and enter 4128 from the keypad
Use the above illustrated installer menu to align the dish for
maximum signal strength. You should have the assistance of
a second person to monitor the television screen while you
complete the adjustments to the satellite dish. As you align
the dish for optimum signal strength, the signal level bar will
increase in length from left to right and will change colour
from red (no signal) to yellow (marginal signal) to green
(good signal). Continue to align the dish until you achieve
maximum strength. Under clear sky conditions and
depending on your location, you should be able to achieve a
signal strength of between 80 and 90% . In addition to the
visual signal strength indicator, the receiver also emits an
audio beeping that wil increase in speed as signal strength
increases and become a monotone once you have aligned
the dish to the satellite and achieved approximately 50%
signal strength. When audio beep becomes monotone, the
front panel signal LED should change from Red to Green,
indicating signal lock on the satellite.
8. Tighten the dish clamp screws.
9. Now make small adjustments to the elevation of the
dish to see if you can further improve on the signal
strength. Loosen the Elevation Adjustment Bolts and
make slight adjustments (1/2 degree increments) in the
elevation, finding the maximum signal strength. When
you’ve located the maximum signal strength possible,
securely tighten all bolts.
10. As a last step, adjust the skew of the dish according
to the skew setting you recorded for the location where
you are installing the dish. Again, make small
adjustments as your assistant monitors the signal
strength. When you have reached maximum signal
strength tighten the screw to lock down the skew setting.
NOTE do not be discouraged if you do not acquire signal on
your first attempt. Be patient and try again. Recheck the
pipe mast for true vertical 90 degrees. Once you acquire
signal, you may need to make very small adjustments to the
dish compass heading (azimuth), elevation and skew settings
to maximize signal strength to between 80 and 90% as
displayed on the installer menu.
Aligning Dish To Acquire Shaw Direct Signal
With receiver on and your assistant ready to monitor signal
strength on the installer menu displayed on the TV, you are
now ready to make adjustments to the dish to acquire the
Shaw Direct satellite signal.
SIGNAL VERIFICATION
1. Refer to the compass, elevation and skew settings for your
location that you recorded on Page 13.
The front panel of the satellite receiver will indicate if the
correct Shaw Direct signal is being received. On the
satellite receiver, beside the ON/OFF power button,
observe the LED satellite signal status indicator light. If
this LED light is GREEN it indicates receiver is tuned to
valid channel and has acquired the correct Shaw Direct
satellite signal.
2. For initial alignment, set the skew to 90 degrees. Skew will
be readjusted to your specific location setting once you
acquire the Shaw Direct satellite signal. TIP: it is easier to
locate satellite signal with skew set to 90 degrees.
3. Check that the dish elevation is set to the elevation
setting listed for your area.
You are ready to proceed to the next step.
8
SAC-00-094
Download from Www.Somanuals.com. All Manuals Search And Download.
If this LED light is RED it indicates NO SIGNAL is being
received by the satellite receiver. The dish is not properly
aligned to receive the Shaw Direct satellite signal.
9. Alternate Tuning Method
Authorizing Receiver for Service
If your receiver installer menu displays signal strength of
between 80 and 90% and the satellite icon LED signal
indicator on the receiver front panel is green, you have
successfully aligned the dish to the Shaw Direct satellite.
Congratulations!
RECEIVER
LNB
Fig. P
You are now ready to call Shaw Direct 1.888.554.7827 to
authorize your receiver for programming. Before calling
record the receiver SN (serial number) and receiver UA
(unit address) from the bar code label on the back panel
of the receiver or from the bar code label that is applied
to the receiver’s shipping carton. Record these numbers
below for future reference
SN (Serial Number, 16 digits) _________________________
UA (Unit Address),
0 0 0 – 0 __ __ __ __ - __ __ __ __ __ - __ __ __
You may prefer to locate the satellite using a SF-100
Satellite Finder (see Figure P), a standalone satellite
signal finding meter which can be purchased separately
from Shaw Direct or your Shaw Direct retailer.
8. Fine Tuning
Step 1: Keep the Tune in Satellite Signal box on-screen.
Tune to channel 299 or 284.
Step 1: Connect a short coaxial cable from the LNB
terminal on the Satellite Finder to the Quad LNB.
Connect the receiver terminal on the meter to a coaxial
cable, which in turn connects to the SAT IN port on the
Shaw Direct receiver.
Fine tuning the Azimuth:
Step 2: After the receiver downloads the channel map,
move the dish back and forth slightly, about a millimeter
to attempt to acquire the highest reading possible on the
signal strength meter.
Step 2: For model DSR205 and DSR315 satellite
receivers set receiver to channel 284. For model DSR5XX
series and DSR207/209 and DSR317/319 receivers set
receiver to channel 299. Note, for satellite finder and
LNB to function, they must be connected to a satellite
receiver, plugged in and turned on.
Step 3: Once you have found the maximum signal
strength, lock the azimuth rotation position in place by
tightening the Azimuth Clamp Bolts (see Figure C).
NOTE: Fine tuning to a high signal strength reduces
signal interference in adverse weather conditions.
Although the maximum possible signal strength is 99,
you will most likely not reach this level.
Step 3: Adjust the dish as closely as possible to the
elevation and azimuth settings you recorded earlier.
Fine tuning the Elevation:
Step 4: Move the dish azimuth rotation very slightly to
the right of the reference mark you drew earlier.
Step 4: Loosen the Elevation Adjustment Bolts and make
slight adjustments (1/2 degree increments) in the
elevation, finding the maximum signal strength, as you
did in the azimuth tuning process. When you’ve located
the highest signal possible, securely tighten all bolts.
Step 5: Slowly rotate the dish back toward the reference
mark and and listen for pitch changes in the audible tone.
If your elevation is set correctly, you should hear two
major pitch changes as it picks up satellite signals. A
weak first change of pitch may be the wrong satellite.
Continue rotating the dish until the second major
deflection, which will be SAT A (107.3), your intended
target.
Step 5: Repeat steps 2-4 to obtain the highest reading
possible on the signal strength meter.
Step 6: If you’ve purchased a second receiver, connect a
second coaxial cable to the SATELLITE IN terminal of the
second receiver.
Step 6: When you have located SAT A, move the dish
slightly to the right and left of the mark until you’ve
maximized the signal. Then tighten the Azimuth Clamp Bolts.
Verify you’ve located the correct satellite (see Section 7,
Step 8).
Step 7: Once connected, allow 5 minutes for the channel
map to download. Confirm the signal strength by checking
the on-screen Tune in Satellite Signal box (see Section 7).
ꢀ You have just completed Fine Tuning.
Skip ahead to the Getting Activated section.
9
SAC-00-094
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 7: While listening to the meter, apply gentle
pressure to the top of the dish to move the dish – first
slightly downward, then upward to see if you can increase
the signal strength further. Carefully adjust the elevation
until you’ve maximized the signal. Tighten the Elevation
Adjustment Bolts.
Step 8: Repeat Steps 2-4 described in Fine Tuning
(Section 8) to obtain the highest reading possible on the
signal strength meter.
Step 9: The dish should now be peaked to its maximum.
Remove the Satellite Finder and plug the LNB directly
into the receiver. Confirm the signal strength by checking
the on-screen Tune in Satellite Signal box as described in
the previous section.
IMPORTANT : For more information on grounding
refer to the receiver’s User Guide included with your
Shaw Direct system.
ꢀ
Your system is now fine tuned and ready for activation.
10. GroundingtheCoaxialCable
Fig. Q
The Shaw Direct dish kit includes the following items to
ground the outdoor coaxial cable
• Coax cable connector Grounding Block
• Grounding Wire
• Grounding Clamp
Outdoor coaxial cable that may be subject to static
discharge or contact with electrical wiring, must be
grounded through a grounding block located as close as
possible to the cable entry point.
• Run the Grounding Wire for the coaxial cable from the
Grounding Block connector to a cold water pipe nearest
the cable entry point.
• Wrap copper grounding strap around cold water pipe.
Tighten strap using bolt and secure the ground wire
under the binding post nut as illustrated below
Ground block (shown with 2 coax cable feeds And ground
wire secured to binding post,)
10
SAC-00-094
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Troubleshooting
Problem #1: I’m having trouble finding the satellite signal.
Try each of the following:
• The cable can be plugged into any of the 4 available
ports on the quad LNB, but must be plugged into the SAT
IN port on the Shaw Direct receiver.
• Make sure all cables are secure and re-verify your
azimuth, elevation and skew setting for your location.
Make sure the mast’s straight section is plumb.
• Adjust the elevation by +1 degree from the setting you
recorder earlier and repeat the steps in "Tuning to the
Satellite".
• Adjust the elevation by –1 degree from your original
setting you recorder earlier and repeat the steps in
"Tuning to the Satellite".
• Ensure cables are connected properly at the grounding
block.
Problem #2: I can’t change channels.
Try each of the following:
• Power cycle the receiver by unplugging it, waiting for
30 seconds, and plugging it back into the AC outlet. Turn
on the receiver and try selecting channel 284 or 299
again with your remote.
• If you are still unable to select 284 or 299, consult with
Shaw Direct.
If you still can’t select or acquire signal on 284 or 299
and the digits A4 do not appear in the Satellite Box in
the Tune in Satellite Signal screen, call us at
1.888.554.7827 to reactivate your system.
11
SAC-00-094
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite Locator Chart
Satellite Look angles are listed for both the 107.3W deg & 111.1W deg satellites. Use the settings for SAT B for dual satellite dish aiming.
The reception of satellite signals in areas with a dish elevation less than 12 degrees may not be possible. Consult with your Shaw Direct retailer
in your area. All information is listed in degrees.
Satellite ‘A’
Satellite ‘B’
Satellite ‘A’
Satellite ‘B’
Town/City
Town/City
Moncton
252
249
251
250
249
250
22.7
23.8
22.6
23.9
23.6
24
123
256 20.5 125
Newfoundland
Napadogan
Newcastle
Oromocto
Plaster Rock
St. John
122
122
123
121
253 21.6
124
Bonavista
264
262
260
263
262
259
262
251
14.4
13.8
17
126
120
124
125
125
114
119
267
265
263 14.8
266 12.8
265 13.5
262
265
254
262
262 13.6
262 12.2
266 13.2
262 16.2
264 12.4
12.1
11.9
127
121
125
126
126
115
120
118
117
120
116
128
126
120
116
124
128
129
118
255 20.4 124
Cartwright
Corner Brook
Gander
Grand Falls
Hebron
Indian Harbour
Labrador City
Nain
North West River
Nutak
Placentia
Port aux Basques
Rigolet
Schefferville
St. Anthony
St. John's
Trepassey
Wabush City
253 21.6
252 21.5
254 21.7
125
123
125
15
123
15.7
13.6
13.6
19.1
12
Quebec
11.7
17.3
12.7
Alma
Amos
242
231
24.7
27.6
19.6
26.9
22.4
24.9
26.9
26.9
26.8
25.7
24.9
24.4
27.8
24.7
26.1
26.2
27.1
118
114
121
120
119
119
120
114
119
119
115
118
120
117
119
119
119
111
118
117
117
121
118
120
117
119
118
107
105
119
112
109
113
118
119
124
114
117
113
120
120
114
117
115
117
120
120
246 22.7 120
116
235 25.9
258 17.5
116
123
258
259
259
263
258
261
14.4
15.5
13.8
15.5
18.5
14.3
17.8
14.4
14.6
15.4
19
116
119
115
127
125
119
Anticosti
Asbestos
Baie Comeau
Baie St.Paul
Asbestos
Beattyville
254
242
248
244
242
232
246 24.9 122
251 20.4
248 22.9
121
121
246 24.9 122
237 25.2
245 24.7
247 23.7
116
121
121
117
251
115
255
266 12.3
267
267
254
16.1
Cap-de-la-Madeleine 241
262
264
263
251
122
127
128
116
Charlesbourg
Chibougamau
Chicoutimi
Cowansville
Dolbeau
243
238
243
240
241
242
242
241
12.3
13.1
17.2
242
23.1
247 22.5 120
244 25.7 122
245 22.8
119
121
121
121
113
Nova Scotia
Donnacona
Dosquet
246
246
245
235
24.1
24.1
25.1
23
Bridgewater
Cape Breton Is.
Chesterfield In.
Dartmouth
Freeport
252
256
208
254
250
256
256
250
258
251
23.7
20.5
17.5
22.9
24.8
21
21
24.9
21.1
24.6
19.9
22.3
25
125
125
98
256 21.3
260 18.2
212
257 20.6 127
254 22.5 126
259 18.6
260 18.6
254 22.5 127
261 18.6 129
255 22.2 127
261
257
127
127
100
Drummondville
Eastmain
Festubert
Fort Coulonge
Gagnon
Gaspe
Gatineau
Granby
Grand Mere
Hauterive
Hull
Inukjuak
Ivujivik
16.9
231
24.5
26.2
29.3
20.4
20.7
29.1
27.6
25.1
22.5
29.1
125
124
125
125
125
128
125
125
125
125
125
240
233
248
253
235
240
241
244 24.2 120
237 27.4
252 18.6
256 18.6
119
118
123
120
Mulgrave
127
127
Port Hawkesbury
Port Maitland
Sable Is.
Shelburne
Sydney
Truro
Wedgeport
Yarmouth
239
27.1
244 25.6 122
245 23.2
251 20.5
119
121
257
254
250
250
17.6
20
127
126
248
235
235
240
239
252
234
228
240
243
256
230
235
232
249
253
234
241
239 27.2 120
254 22.6 127
254 22.7 127
19
239
17.8
109
106
121
113
111
25
15.4
27.5
15.8
21.5
27.8
26.1
25.7
20.1
28
28.5
26.5
22.3
19.5
26.2
24.6
26.8
28.1
21.1
244 14.4
243 25.5
256 14.4
238 20.1
233 26.2
244
247 23.7
259 17.8
235 26.2
239 26.6
236 24.8
252 20.3
257
238 24.5
245 22.8
239
239 26.2
255 19.1
Joliette
Prince Edward Island
Kuujjuaq
Kuujjuarapik
La Sarre
La Tuque
Levis
Madeleine
Malartic
Maniwaki
Matagami
Matane
Charlottetown
254
21.7
124
258 19.4
126
115
120
121
125
116
119
115
121
122
116
119
118
119
122
24.1
New Brunswick
Bath
Bathurst
Chatham
Dalhousie
Edmundston
Fredericton
Grand Manan Is.
Hartland
248
251
251
250
247
250
249
248
249
24
122
122
122
121
120
123
124
122
121
252 21.9
255
255 20.3 124
254 20.2 123
251
123
123
22.2
22.5
22.3
23.8
23.9
24.9
24.1
20.1
21.7
21.7
122
124
253
Mingan
17.5
253 22.6 126
252
252
Miquelon
Mistassini
Monet
Mont Laurier
Mont Louis
Montmagny
22
21
124
123
Kedgwick
23.1
235
235
251
25
244
25.3
248 23.2 122
12
SAC-00-094
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite ‘A’
Satellite ‘B’
Satellite ‘A’
Satellite ‘B’
Town/City
Town/City
Brampton
Brockville
Burlington
Carleton Place
Chapleau
Chatham
Cobalt
227
235
227
234
220
223
227
230
225
226
237
218
232
198
221
228
202
223
222
224
197
212
234
212
32.6
29.8
32.9
29.6
30.4
34.8
29.3
31.6
28.3
32.1
116
118
116
117
110
115
113
117
111
115
119
110
116
102
112
115
104
113
111
109
102
103
118
107
117
115
112
116
116
116
116
115
109
108
115
103
116
112
110
101
114
118
113
116
116
113
115
107
107
106
117
120
112
112
115
109
232 30.7
239 27.8
119
121
119
Montreal
Mont Joli
Natashquan
Noranda
Parent
Paspebiac
Pointe aux Anglais 249
Pointe-aux-Tremble 239
239
247
256
229
237
251
28
22.9
18.4
28.2
26.6
21.7
21.6
27.8
21.2
14.1
25.8
23.1
24.1
21.5
25
28.2
15
27.3
20.8
26.7
20
27.2
27.3
23.5
27.9
26
25.5
16.1
32
23.8
27.6
28
28
27.4
28
24.7
24.5
24.3
24.8
24
26.8
27.8
28.5
26.1
28
119
119
121
113
116
121
119
119
119
109
119
119
119
119
117
113
106
114
119
119
120
120
119
119
118
119
119
121
99
119
119
119
118
118
119
119
119
119
123
119
119
114
119
117
119
119
111
243
26
251 20.9
260 16.3
233 26.5
121
121
123
116
119
123
121
121
121
110
121
121
121
121
119
116
107
117
121
121
121
122
121
121
120
121
121
123
102
121
121
232
31
238 27.6 120
224 28.9
227 33
232 27.6
235 29.6 120
229 26.8
231 30.2
113
118
116
241
255 19.6
253 19.6
243 25.8
253 19.2
256 12.8
247 23.7
251
249
253
245
233 26.5
248 14
236 25.6
254 18.8
244 24.7
256
246
244 25.3
250 21.5
24.7
Cobourg
Cochrane
Collingwood
Cornwall
Dalton
Deep River
Dryden
Elliot Lake
Emsdale
English River
Espanola
Foleyet
Fort Albany
Fort Frances
Fort Severn
Gananoque
Geraldton
Gilmour
Goderich
Gogama
Gravenhurst
Guelph
Haliburton
Hamilton
Hanover
114
118
121
112
118
Port Cartier
Quaqtaq
Quebec
250
253
243
247
245
249
241
229
244
232
250
240
252
242
240
246
29
241
26.9
30.3
29.4
31.1
223 28.8
236 27.6
203 30.3 105
226 29.7
232 28.9
207 30.3 107
227 29.5
226 28.2
229 24.3
202 31.6
216 22.9 105
238 28.2 121
216 28.5 109
236 28.7
228 31.6
228 28.3
233 29.3
Rimouski
21.1
22.1
19.5
23.1
Riviere-du-Loup
RivierePentecote
Roberval
Rouyn
Salluit
Senneterre
Sept Iles
Shawinigan
Sheldrake
Sherbrooke
Sorel
31.3
30.7
31.4
31.2
29.8
25.6
32.6
23.8
30.2
29.8
30.6
33.4
29.9
31.1
115
118
115
114
111
105
18
25.1
St Paul du Nord
231
119
117
114
118
119
119
119
118
112
111
St.Agathe-des-Monts238
St. Agapit 242
St. Anne de Beaupre 243
St. Augustin
St. Boniface
St. Eloi
St. Hyacinthe
St. Jean
St. Jerome
242
246
247 23.4
263
193
250 21.8
244 25.5
26
24
223
223
229
226
231
227
225
219
259
188
246
240
239
238
14.1
31.3
32.9
30.6
33
231
235 28.7
232 31.1
31
32.7
28.7
29.5
30.9
31.4
33.7
28.4
28.5
31.6
33
30.5
28.7
33.1
31.5
31.5
33.9
29.5
29.1
229 30.9
224 27.3
221 28.2
243 25.9 122
Hearst
242
243 25.4
243 26
249 22.6
249 22.4
249 22.3
26
121
121
121
121
121
121
Hornepayne
Huntsville
Ignace
217
St. Jean de Matha 239
228
201
225
225
222
194
223
234
227
226
229
223
224
213
233
29.1
118
St. Laurent
St. Pacome
St. Pascal
St. Simeon
St. Stephen
Tadoussac
Trois-Rivieres
Val d'0r
Valleyfield
Vandry
Verdun
Victoriaville
Waskaganish
Wemindji
239
245
245
245
249
245
241
205 30.3 106
230 31.8
230 26.9
Ingersoll
119
114
113
Iroquois Falls
Kapuskasing
Kenora
Kincardine
Kingston
Kirkland Lake
Kitchener
Lindsay
Little Current
London
Longlac
Lynx
Macdiarmid
Madoc
226
199
27.1
30.7 104
252 22.5 125
249
245 24.8
235 26.1
242 26.4
243 24.2
22
121
121
116
121
119
121
228 31.2
238 28.5
117
121
115
119
119
115
118
110
110
231
231
27.1
238
239
239
242
230
231
230 31.2
234 29.6
227 29.8
243
26
26.7
25.3
24
246 24.6 122
234 23.8
235 22.5
229
218 28.3
218 27.8
32
113
112
122
110
120
214
209
232
241
Windsor
241
27.1
245
25
30.4
30.8
27.4
31.9
29.2
29.8
28.7
214 29.2 109
236 28.8 120
245 25.3 122
226 30.3
230 27.6
Ontario
Magog
Apsley
231
234
231
227
232
220
228
228
30.8
29.4
30.5
31.9
31
116
117
116
116
117
112
115
116
235 28.9
238 27.5 120
235 28.6
232
236
225
232 29.3
232 30.2
119
Manitoulin I.
Matachewan
Mattawa
221
115
115
117
112
Arnprior
Bancroft
Barrie
Belleville
Blind River
Bracebridge
Bradford
225
229
220
119
118
120
115
118
119
234
28
30
29
30
Mattice
224 27.2
31.6
31.2
32.1
13
SAC-00-094
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite ‘A’
Satellite ‘B’
Satellite ‘A’
Satellite ‘B’
Town/City
Town/City
Mekatina
Michipicoten
Midland
Milne Inlet
Mobert
Moosonee
Nakina
New Liskeard
Newcastle
Nipigon
North Bay
Oakville
Oba
Opasatika
Orillia
218
216
227
259
215
31.4
30.8
31.7
110
223 29.9
221 29.4
113
112
118
99
111
112
109
116
119
Temiscaming
Thessalon
Thetford Mines
Thunder Bay
Timmins
Tionaga
Tobermory
Toronto
229
219
29.6
31.8
26.3
31.7
29
29.6
32
32.4
31.1
30.4
34.7
33.1
32.9
32
30.3
35.3
33.1
23.9
33.5
114
111
120
106
111
233 27.9
224 30.2
247 24.3 122
211 30.5 108
228 27.4
227 28.1
228 30.3
232 30.5
236 29.2 120
117
114
109
115
98
108
110
107
113
117
106
114
116
109
110
116
117
118
105
106
114
108
91
115
116
115
118
116
117
103
118
99
116
112
101
117
116
110
115
111
231
263
219
29.9
6.6
29
243
206
224
222
223
228
232
228
222
226
228
229
230
221
7.1
30.4
26.2
29.2
29.2
31.8
30.9
30.1
32.7
29.5
28.6
31.6
31.9
29.1
18.3
31.2
32.3
28.9
5.4
31.2
29.5
31.7
114
114
116
119
226
212
230 24.7
217 28
232 27.5
234 29.9
111
113
116
117
115
115
116
117
117
116
115
115
105
116
227
230
209
228
227
218
221
228
229
235
233
208
225
216
Trenton
213
29.7 109
Trout Creek
Wallaceburg
Waterloo
Welland
Whitby
Whitney
Windsor
Wingham
Winisk
232 28.6
227 32.9
230 31.2
117
118
118
120
119
118
118
118
232 28.4
232 30.8
117
119
112
112
118
119
223
225
28.1
27.1
233
233
31
30.1
232 29.7
233 30
239 27.2 120
234 28.4
225 33.5
229 31.3
222 22.8 107
230 31.6
Oshawa
Ottawa
224
217
225
Ottawa Is.
Oulmet
Owen Sound
Pagwa River
Parry Is.
Parry Sound
Pembroke
Penetanguishene
Perth
Petawawa
Peterborough
Pickle Crow
Picton
Port Nelson
Port Stanley
Ramore
Red Lake
Renfrew
Richmond Hill
Sand Lake
Sarnia
Sault Ste Marie
Savant Lake
Schreiber
Simcoe
237
213
17.2
30
107
109
117
110
92
117
119
118
120
119
119
Woodstock
119
229 30.5
220 27.6
Manitoba
194
198
231
5.3
29.4
Brandon
Dauphin
Emerson
Flin Flon
182
181
32.4
31
96
187
31.9
99
99
227
232
227
234
232
230
205
232
200
224
226
196
233
228
217
222
217
203
211
226
200
234
201
228
224
224
225
227
225
221
96
99
94
98
96
97
98
94
96
98
98
97
94
97
99
100
186 30.5
193 32.2 102
182 26.9
193 30.5
188 28.3
237 27.6
231 29.9
238 27.9
236 27.6
234 29.4
209 27.8 106
237 29 120
204 22.9 102
229 32.3
230 27
188
177
188
183
185
187
179
182
186
185
186
178
186
188
200
32.9
27.3
31.2
28.8
30.2
30.6
25
97
101
99
29.8
29.5
31.3
28.9
31
Gimli
Grand Rapids
Gypsumville
Hodgson
Lynn Lake
Minnedosa
Morden
Portage la Prairie
Norway House
The Pas
Thompson
Winnipeg
189 29.6 100
192
183
187
191
190
191
30
101
97
99
101
101
24.7
31.4
32.2
31.4
23.7
34.1
28.6
30.2
29.6
32.2
30.8
34.4
31.9
30.2
30.8
33.6
30.7
29.7
32
32
119
115
32.8
32.1
27.8
28.3
25.9
32
201 29.3 104
27.2 100
237 27.6
232 30.3
222 29.4
227 32.6
222 30.4
208 29.1
215 29.5
119
119
112
118
113
106
110
119
183
191
193
27.9
25.3
31.3
97
99
102
York Factory
23.7
204 22.9 102
104
107
116
103
118
103
117
116
114
115
114
113
111
Saskatchewan
Assiniboia
Beauval
Biggar
169
165
165
175
164
177
169
161
162
171
170
171
164
172
165
168
167
33.1
27.1
91
90
90
94
90
94
91
88
88
92
91
92
89
92
90
91
174
169
32.9
27
94
93
92
97
92
97
94
91
231
31.6
Sioux Lookout
Smiths Falls
Steep Rock Lake
St. Catharines
St. Thomas
Stokes Bay
Stratford
Sturgeon FaIIs
Sudbury
Sultan
205 29.7 106
239 27.7 120
206 30.9 106
233 30.8 120
229 32.2
228 30.4
229 31.5
231 28.5
229 28.9
225 28.8
30.4
33.5
22.6
30.8
27.1
29.1
32.7
29.5
32.2
31
29.7
32.1
31
29.8
30.3
170 30.4
180 33.1
168 22.6
182 30.4
Estevan
Fond du Lac
Kamsack
La Ronge
Lloydminster
Maple Creek
Melfort
Moose Jaw
Nokomis
North Battleford
Regina
32.8
34
119
117
118
117
116
114
115
174
165
26.9
29.1
32.2
33.4
30.3
30.6
30.3
28.8
31
167 32.8
91
176
175
176
29.3
32
30.8
95
95
95
92
95
93
94
94
Swastika
Tannin
227
202
113
104
231
27.2
169 29.6
207 29.9 106
177
170
173
172
31.8
30.9
29.6
30.2
Rosetown
Rosthern
Saskatoon
91
14
SAC-00-094
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite ‘A’
Satellite ‘B’
Satellite ‘A’
Satellite ‘B’
Town/City
Town/City
Shaunavon
Sherridon
Stanley
Swift Current
Tisdale
Uranium City
Watrous
Weyburn
Wilkie
165
178
170
166
173
161
170
174
163
176
33
89
94
92
90
93
89
91
93
89
94
169
183 24.4
175
170
177
33
92
97
94
93
95
91
95
96
92
97
Hazelton
133
140
144
145
132
139
141
139
139
149
140
145
134
138
139
130
140
24.5
24.8
30.7
31.7
25.3
31.6
30.3
25.7
31.4
32.4
31.6
32
29.2
31.9
26.8
24.7
27.8
25.1
30.7
32.2
32
77
80
79
80
75
76
78
79
76
82
77
80
74
75
79
74
79
72
81
76
76
75
77
75
76
81
75
77
80
99
76
79
137
144 25.4
149
150 32.3
136 26.2
144 32.5
25.3
79
83
82
83
78
79
81
24.8
26.4
32.4
29.5
22.4
30.8
32.9
30
Hudson Hope
Kamloops
Kelowna
Kitimat
Ladysmith
Lillooet
McLeod Lake
Nanaimo
Nelson
New Westminster
Penticton
Port Alice
Port Renfrew
Prince George
Prince Rupert
Quesnel
Queen Charlotte Is 127
Revelstoke
Saanich
26.2
32.3
29.2
31.3
165 22.4
175
179
168
181
30.6
32.6
30
146
31
143 26.4
144 32.3
154 32.9
145 32.4
150
139 30.2
143 32.9
144
134
145 28.5
132 26.3
152
145
145 32.9
82
79
85
80
83
77
79
82
77
82
75
84
79
79
78
80
78
78
84
78
80
83
Yorkton
31.2
30.8
Alberta
32.7
Athabasca
Banff
Bassano
Brooks
Calgary
154
151
27.3
30.9
31.6
86
83
86
86
85
86
83
86
86
83
88
87
87
85
82
86
83
82
87
85
85
85
83
84
87
83
85
86
87
87
87
85
159
156
162
163
159
160 29.4
156
161
27.5
31.3
31.8
32
89
86
89
89
88
89
86
89
88
86
90
90
90
87
85
89
85
85
89
88
88
89
86
86
90
86
88
89
89
89
90
88
27.5
25.7
157
158
154
156
151
31.9
31.2
31.4
Camrose
29.2
32.7
30.9
28.6
28.2
23.2
24.8
25.3
23.2
26.2
30.8
25.1
28.7
27.4
29.7
28.9
32.8
25.9
22.4
32.5
25.3
29.9
29.9
28.7
28.7
29
147
140
140
135
140
130
128
148
136
140
146
189
140
141
31.2
33.1
Cranbrook
Drumheller
Edmonton
Edson
Fort Chipewyan
Fort MacKay
Fort McMurray
Fort Vermilion
Grande Prairie
Hanna
33.1
31.1
156
154
149
156
156
157
148
145
158
145
147
156
154
154
156
148
145
160
147
154
156
157
157
159
155
Sidney
159 28.8
154 28.6
Simoom Sound
Squamish
Stewart
Telegraph Creek
Trail
Vancouver Is.
Vancouver
Vernon
Victoria Beach
Victoria
29
31
139
145
134
132
30
31.9
24.1
21.8
161
160 24.9
161 25.4
152 23.5
149 26.7
162 30.9
149 25.6
151
161
159
159
161
152 26.3
149 22.7
165 32.6
151 25.7
159 30.2
161
161
161
164
23.2
23.1
20.9
32.8
30
31.5
31.3
31
153 33.4
141 30.9
145 32.4
150 31.9
194 30.3 102
Hines Creek
Jasper
Lac Ia Biche
Lacombe
29.2
27.5
30
29.1
33
32.3
28.8
145
146 29.5
33.1
79
82
Williams Lake
Leduc
Nunavut
12.8
7.1
14.8
5.4
12.4
7.6
Lethbridge
McLennan
Meander River
Medicine Hat
Peace River
Red Deer
Amadjuak
Arctic Bay
252
253
158
211
106
255
257
162
215
169
272
237
265
201
261
11.7
6.7
107
98
91
93
92
97
90
92
91
108
93
Bathurst Inlet
Bathurst Is.
Cambridge Bay
Cape Dyer
Cornwallis Is.
Devon Is.
Eskimo Point
Frobisher Bay
Gjoa Haven
Igloolik Is
Kangirsuk
Lake Harbour
Mackenzie King Is. 134
Padlei
Padloping Is
Pangnirtung
Pelly Bay
Qurlurtuuq
Rankin Inlet
Repulse Bay
Resolute
14.8
5.2
12.3
6.4
5.9
5
165
268
233
261
197
257
198
247
251
254
Stettler
30.1
28.9
28.9
29.1
109
94
97
99
109
96
101
111
109
90
98
108
108
98
88
100
100
94
Vegreville
Vegreville
Vermilion
Wetaskiwin
6.1
5.4
19.8
11.7
12.5
10.3
15
12.8
4
19.3
7.7
9.2
11.9
13.6
17.8
13.4
6.5
96
97
19.3
10.5
29.2
159 29.4
107
94
100
110
108
89
96
107
107
97
202 12.2
British Columbia
251
255
258
138
194
271
267
227
146
209
232
235
9.6
13.7
11.6
4
18.8
6.6
8
11.4
13.7
17.2
12.7
6.2
Ashcroft
Atlin
142
125
139
137
142
139
140
136
138
141
30.4
18.7
31.7
30.6
25.4
31.9
32.2
23.9
21.9
24.8
79
75
76
75
81
76
76
79
81
147
129
144 32.5
142
147
144 32.7
145
141
142 22.5
146 25.4
31.1
19.7
82
77
79
78
84
79
79
81
Chemainus
Courtenay
Dawson Creek
Duncan
Esquimalt
Fort Grahame
Fort Nelson
Ft St. John
190
268
264
223
142
205
228
231
31.5
26
33.1
24.6
87
98
99
93
83
83
81
15
SAC-00-094
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite ‘A’
Satellite ‘B’
Notes
Town/City
Resolution Is.
Somerset Is.
Southampton Is.
Spence Bay
Tavani
259
226
230
212
200
213
12.2
8
110
94
101
95
97
97
97
263
230
234 14.2
216 11
204 18.3
10.9
7.7
112
95
102
97
99
99
99
14.9
11.4
18.9
14.7
18.3
Wager Bay
Whale Cove
217
206
14.1
17.8
201
Northwest Territory
Arctic RedRiver
Banks Is.
Fort Franklin
Fort Good Hope
Fort Liard
Fort Norman
Fort Reliance
Fort Simpson
Fort Smith
Ft McPherson
Ft Providence
Ft Resolution
Hay River
Holman Island
Inuvik
Jean Marie Rvr
Melville Is.
Nahanni Butte
Norman Wells
Port Radium
Rae
120
126
132
126
136
130
158
138
154
120
143
150
147
135
120
139
144
135
129
139
145
155
120
149
134
148
11.6
7.9
79
86
83
81
124
130
136
130
12.3
8.2
15.8
14.2
81
87
84
82
83
83
91
85
90
80
86
89
87
88
81
85
90
83
83
87
87
90
82
90
84
88
15.3
13.6
20.3
15.4
19
81
140 20.9
82
89
83
87
79
84
87
85
86
80
83
89
81
134
162
142
159
124
148 20.3
155
151
139
124
143
148
140
133
143
149
159
124
154
138
152
15.9
19
19.6
21.9
12.1
19.1
21.8
11.4
20
20.5
20.7
10.5
10.9
19.4
6
19.5
14.8
15.1
18.6
19.4
10
10.5
17.3
19
20.7
20.9
10.7
11.5
19.9
6
20
81
15.3
15.3
18.8
19.4
10.5
10.5
17.8
19.2
85
86
88
81
89
82
86
Snowdrift
Tuktoyaktuk
Victoria Is.
Wrigley
Yellowknife
Yukon Territory
Big Salmon
Carmacks
Dawson
Forty Mile
Keno Hill
122 2216.3
76
75
75
75
77
75
77
77
75
75
76
78
75
127
125
122
121
125
122
125
120
122
128
129
17.2
16.7
14.3
13.7
15.2
14.3
15.3
11.1
78
77
77
77
79
77
78
79
76
77
78
80
77
121
118
117
15.8
13.3
12.8
14.4
13.4
14.5
10.3
14
121
118
121
116
118
124
125
129
123
Klondike
Mayo Landing
Old Crow
Stewart River
Tagish
Teslin
Watson Lake
Whitehorse
14.9
18.9
19.3
17.9
18.5
19.4
17.4
134 20.2
127
18.3
Canadian Arctic Islands
Prince Charles Is.
Prince of Wales Is
Prince Patrick Is.
254
197
121
10.3
8.3
4.2
2.9
102
93
87
92
258
201
125
259
9.5
8.1
4.3
2.8
103
94
88
93
Queen Elizabeth Is 256
16
SAC-00-094
Download from Www.Somanuals.com. All Manuals Search And Download.
|