ONE YEAR LIMITED WARRANTY
SI PRODUCTS sells its products with the intent that they are free of defects in manufacture and
workmanship for a period of one year from the date of original purchase, except as noted below.
SI PRODUCTS warrants that its products will be free of defects in material and workmanship under
normal use and service. This warranty extends only to consumers and does not extend to Retailers.
To obtain warranty service on your SI PRODUCTS product, mail the product and your dated sales receipt
(as proof of purchase), postpaid, to the following address:
SI PRODUCTS Consumer Relations
Service Center Dept. 168
3000 Pontiac Trail
Commerce Township, MI 48390
No COD's will be accepted.
SI PRODUCTS does not authorize anyone, including, but not limited to, Retailers, the subsequent
consumer purchaser of the product from a Retailer or remote purchasers, to obligate SI PRODUCTS in any
way beyond the terms set forth herein. This warranty does not cover damage caused by misuse or abuse;
accident; the attachment of any unauthorized accessory; alteration to the product; improper installation;
unauthorized repairs or modifications; improper use of electrical/power supply; loss of power; dropped
product; malfunction or damage of an operating part from failure to provide manufacturer’s recommended
maintenance; transportation damage; theft; neglect; vandalism; or environmental conditions; loss of use
during the period the product is at a repair facility or otherwise awaiting parts or repair; or any other
conditions whatsoever that are beyond the control of SI PRODUCTS.
SI Products
Service Center
1.888.856.6781
8:30a.m. – 7:00p.m. (EST)
M – F
Mail To: SI Products
Consumer Relations
Service Center Dept. 168
3000 Pontiac Trail
Commerce Township, MI
48390
This warranty is effective only if the product is purchased and operated in the country in which the
product is purchased. A product that requires modifications or adoption to enable it to operate in any
other country than the country for which it was designed, manufactured, approved and/or authorized, or
repair of products damaged by these modifications is not covered under this warranty.
THE WARRANTY PROVIDED HEREIN SHALL BE THE SOLE AND EXCLUSIVE WARRANTY. THERE
SHALL BE NO OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS OR ANY OTHER OBLIGATION ON THE PART OF THE COMPANY WITH
RESPECT TO PRODUCTS COVERED BY THIS WARRANTY. SI PRODUCTS SHALL HAVE NO LIABILITY FOR
ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES. IN NO EVENT SHALL THIS WARRANTY
REQUIRE MORE THAN THE REPAIR OR REPLACEMENT OF ANY PART OR PARTS WHICH ARE FOUND TO BE
DEFECTIVE WITHIN THE EFFECTIVE PERIOD OF THE WARRANTY.
e-mail:
NO REFUNDS WILL BE GIVEN. IF REPLACEMENT PARTS FOR DEFECTIVE MATERIALS ARE NOT AVAILABLE,
SI PRODUCTS RESERVES THE RIGHT TO MAKE PRODUCT SUBSTITUTIONS IN LIEU
OF REPAIR OR REPLACEMENT.
This warranty does not extend to the purchase of opened, used, repaired, repackaged and/or resealed
products, including but not limited to sale of such products on Internet auction sites and/or sales of such
products by surplus or bulk resellers. Any and all warranties or guarantees shall immediately cease and
terminate as to any products or parts thereof which are repaired, replaced, altered, or modified, without
the prior express and written consent of SI PRODUCTS.
This warranty provides you with specific legal rights. You may have additional rights which may vary from
state to state. Because of individual regulations, some of the above limitations and exclusions may not
apply to you. For more information regarding our product line in the USA,
THE SHARPER IMAGE ® name and logo are registered trademarks.
Marketed and distributed by SI products under license. ©The Sharper Image.
All rights reserved.
IB-EV-HT20
Download from Www.Somanuals.com. All Manuals Search And Download.
Heat any room big or small.
Thank you for purchasing The Sharper Image® Oscillating Tower Ceramic Heater.
This product, along with the entire The Sharper Image collection, connects
innovation with cutting-edge design to provide you with years of dependability
and enjoyment. The oscillating tower heater from The Sharper Image heats any
room from floor to ceiling evenly so you and your family can relax in a comfortable
climate controlled setting when the weather outside turns colder.
IMPORTANT SAFETY INFORMATION:
WHEN USING ELECTRICAL PRODUCTS, ESPECIALLY WHEN CHILDREN ARE
PRESENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED,
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING
DANGER-TO REDUCE THE RISK OF ELECTRIC SHOCK:
• This heater is hot when in use. To avoid burns, do not let bare skin touch hot
surface. If provided, always use handles when moving this heater. Keep combustible
materials such as furniture, pillows, bedding, papers, clothes and curtains at least 3
feet from the front of the heater and keep them away from the sides and rear.
• Extreme caution is necessary when any heater is used by or near children or invalids
and whenever the heater is left operating and unattended.
• Always unplug the heater when not in use.
• Do not operate the heater with a damaged cord or plug, if the heater malfunctions,
has been dropped or damaged in any manner. Return heater to authorized service
facility for examination, electrical or mechanical adjustment, or repair.
Download from Www.Somanuals.com2. All Manuals Search And Download.
• This heater is not intended for use in bathroom, laundry areas and
similar moist indoor locations. Never locate heater where it may fall
into a bathtub or other water container.
Caution: All
servicing of
this product
must be
performed
by
• Do not run cord under carpeting. Do not cover cord with throw
rugs, runners or the like. Arrange cord away from traffic areas
where it can be tripped over.
authorized
SI Products
Service
Personnel
only.
CAUTION: This appliance has a polarized plug (one blade is wider than
the other). To reduce the risk of shock, this plug is intended to fit only
one way in a polarized outlet. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician.
DO NOT attempt to defeat this safety feature. To do so could result in
an electric shock hazard.
• This heater draws 12.5 amps during operation. To prevent
overloading a circuit, do not plug the heater into a circuit that
already has other appliances working.
• CAUTION: It is normal for the plug to feel warm to the touch; however,
a loose fit between the AC outlet (receptacle) and plug may cause
overheating and distortion of the plug. Contact a qualified electrician
to replace loose or worn outlet.
• To disconnect the heater, first turn controls to the OFF position,
then remove plug from outlet. Never pull by the cord.
• Do not insert or allow foreign objects to enter any ventilation or
exhaust opening as this may cause an electric shock or fire, or
damage the heater.
• To prevent a possible fire, do not block air intakes or exhaust in any
manner. Do not use on soft surface, like a bed, where openings
may become blocked.
• A heater has hot and arcing or sparking parts inside. Do not use it
in the areas where gasoline, paint, or flammable liquids are used or
stored.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
• Use this heater only as described in this manual. Any other use not recommended
by the manufacturer may cause fire, electric shock, or injury to persons.
• Always plug heaters directly into a wall outlet/receptacle. Never use with an extension
cord or relocate power tap (outlet/power strip).
CAUTION: Avoid the use of an extension cord because the extension cord may overheat
and cause a risk of fire. However, if you have to use an extension cord, the cord should be
No.14 AWG minimum size and rated not less than 1875 watts.
• The output of this heater may vary and its temperature may become intense enough
to burn exposed skin. Use of this heater is not recommended for persons with
reduced sensitivity to heat or an inability to react to avoid burns.
• Always unplug the heater from the electrical outlet immediately after using and before
cleaning.
• DO NOT place the heater near a bed because objects such as pillows or blankets
can fall off the bed and be ignited by the heater.
• DO NOT reach for an appliance that has fallen into water. Unplug it immediately.
• DO NOT use while bathing or in the shower.
• DO NOT place or store appliance where it can fall or be pulled into a tub or sink.
• DO NOT place in or drop into water or other liquid.
• NEVER use pins or other metallic fasteners with this appliance.
• Keep dry - DO NOT operate in a wet or moist condition.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
WARNING– TO REDUCE THE RISK OF BURNS, ELECTRIC SHOCK, FIRE OR
INJURY TO PERSONS:
• An appliance should never be left unattended when plugged in. Unplug from
outlet when not in use and before putting on or taking off parts or attachments.
• Extreme caution is necessary when this appliance is used by or near children,
invalids or disabled persons.
• Use this appliance only for its intended use as described in this manual. Do
not use attachments not recommended by The Sharper Image; specifically any
attachments not provided with the unit.
• NEVER operate this appliance if it has a damaged cord or plug, if it is not
working properly, if it has been dropped or damaged, or dropped into water.
Return it to SI Products Service Center for examination and repair.
• Keep cord away from heated surfaces.
• NEVER drop or insert any object into any opening.
• DO NOT operate where aerosol (spray) products are being used or where
oxygen is being administered.
• DO NOT operate under a blanket or pillow. Excessive heating can occur and
cause fire, electrocution or injury to persons.
• DO NOT carry this appliance by the power cord or use cord as handle.
• To disconnect, turn all controls to the “off” position, then remove plug from
outlet.
• This appliance is designed for personal, non-professional use only.
• DO NOT use outdoors.
• Check your heater cord and plug connections.
a) Faulty wall outlet connections or loose plugs can cause the outlet or plug to
overheat. Be sure the plug fits tight in the outlet.
b) Heaters draw more current than small appliances, overheating of the outlet
may occur even if it has not occurred with the use of other appliances.
c) During use check frequency to determine if your plug outlet or faceplate is
HOT! If so, discontinue use of the heater and have a qualified electrician
check and/or replace the faulty outlet(s).
SAVE THESE INSTRUCTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Main Features on Oscillating Tower Ceramic Heater
Fig. 1
Function control panel
Temperature readout
LCD screen
Ceramic heating
element
Oscillation
button
Timer
button
POWER
button
Temperature
adjustment
Fig. 2
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification of Main Unit:
Input Voltage: 120V-60Hz
Output Power: 1500W
Current: 12.5A
OPERATING INSTRUCTIONS
Turning the Unit On
• Check that neither the appliance nor the power cable has been damaged
when first using.
• Place the heater on a firm level surface, at least 3 ft. away from any wall and
any other objects such as furniture, curtains, plants or combustible material.
• With the POWER in the “OFF” position. Plug heater into a standard AC outlet.
(See important safeguards regarding use of extension cords)
• Press POWER ON/OFF button once to turn on the heater and the heater will heat
at HIGH heating setting. The screen will display the room temperature and
HIGH indicator will light. When the room temperature is displayed, the “ROOM”
indicator will be lit.
IMPORTANT: Your heater is equipped with a polarized alternating current line
plug (a plug having one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are unable to insert
the plug fully into the outlet, try reversing the plug. If the plug should still fail to
fit, contact your electrician to replace your outlet. DO NOT defeat the safety
purpose of the polarized plug.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
1) Heater Settings
• Turn the power ON by pressing POWER button and press LOW/HIGH button to
switch the heat setting between HIGH and LOW.
2) Turning the Heater Off
• Press the POWER ON/OFF
button to turn the heater off.
• When the unit is turned off, the fan will continue to run for around 15 seconds
to blow out hot air. At the same time display screen will count down from 15
backward to 1. You do not need to hold button down. After the display turns off,
unplug the heater from the electrical outlet.
3) Setting the Temperature
• The default setting temperature is 75°F.
• When the heater is on (HIGH or LOW), press +/- button and the “SET” will be lit.
Continue pressing +/- button to set the temperature desired between 60°F and
95°F.
• The thermostat is in effect in modes: HIGH and LOW only and will heat to the
desired temperature setting.
• The heater has a built in memory function. When the heater is not unplugged
after last time used, press +/- button and display will show the set temperature
from last time. When the heater is unplugged after last time used, the setting
temperature will go back to the default setting temperature. (75°)
Note: If the room temperature is higher than the setting temperature, the unit will
stop heating to save the energy. When the room temperature falls lower than the
setting temperature, the unit will resume heating. The heater will cycle on and off this
way to maintain the set temperature.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
4) Setting the Timer
This heater has a timer that will enable the heater to turn on and off automatically
within 90 Minutes.
• Plug the heater into an outlet, press the TIMER button to set the timer
(0,15,30,…,90 Min) to automatically turn on the heater.
• When the heater is on, press the TIMER button to set the timer (0,15,30,…,90
Minutes) to automatically turn off the heater.
• When displaying the timer, the “MIN” will light
• When the timer is set, the timer symbol
will light.
5) Oscillation
OSCILLATION button is used to start and stop the oscillation of the heater.
When the unit is on, Press OSCILLATION button to start the Auto oscillation; press
OSCILLATION button again to stop the oscillation.
6) “ºC” and “ºF” Conversion
Press +/- button together more than 3 seconds, the display will convert between
“°C” and “°F”
When the temperature is on “°C” mode, the “°C” will light.
When the temperature is on “°F” mode, the “°F” will light
7) Resetting Heater
This heater is equipped with an internal high limit switch that causes the unit to
stop operating in the event the internal temperature exceeds normal operating
temperatures.
IF THE UNIT SHUTS OFF:
1) PRESS POWER ON/OFF BUTTON TO TURN OFF THE HEATER
2) UNPLUG UNIT AND WAIT 10 MINUTES
3) PLUG IN AND PRESS POWER ON/OFF BUTTON AGAIN TO TURN IT ON
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Remote Control
Fig. 3
POWER
ON/OFF
Choose timer
setting
Adjust oscillation
speed
Decrease
Increase
temperature
temperature
Choose HI or LO
fan speed
10
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
If heater fails to operate
• Be sure it is plugged in and that the electrical outlet is working. Check circuit
breaker in case of blown circuit.
• Check for any obstruction. If you find an obstruction press POWER ON/OFF button
to turn the heater OFF. Unplug the heater and wait at least ten minutes for it to
cool. Carefully remove the obstruction. Plug the heater back in and restart it as
described under OPERATION.
• If heater still does not operate, remove the plug from the socket and have the
appliance serviced by authorized service personnel only.
CLEANING AND STORAGE
We recommend that the heater be cleaned at least once a month and before off-
season storage.
– Turn the heater OFF and unplug it. Allow it to cool.
– Use a dry cloth to clean the external surfaces of the heater.
DO NOT USE WATER, WAX, POLISH OR ANY CHEMICAL SOLUTION.
– Clean your heater using the above-mentioned steps, then pack the heater in its
original container and store it in a cool dry place.
– This heater does not disassemble.
– The motor is factory lubricated for life and will require no further lubrication.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|