Sharp Stereo System MD MX20 User Manual

MODEL

MD COMPACT COMPONENT SYSTEM

OPERATION MANUAL

MD-MX20

Thank you for purchasing this SHARP product.

To obtain the best performance from this product, please read

this manual carefully. It will guide you in operating your SHARP

product.

MD-MX20 MD Compact Component System consisting of

MD-MX20 (main unit) and CP-MX20 (speaker system).

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFEGUARDS

CAUTION

All the safety and operating instructions should be read

before the appliance is operated, and should be retained

for future reference.

12 Outdoor Antenna Grounding - If an outside antenna is

connected to the receiver, be sure the antenna system

is grounded so as to provide some protection against

voltage surges and built-up static charges. Section 810

of the National Electrical Code, ANSI/NFPA No. 70-

1984, provides information with respect to proper

grounding of the mast and supporting structure, ground-

ing of the lead-in wire to an antenna discharge unit,

size of grounding conductors, location of antenna-dis-

charge unit, connection to grounding electrodes, and

requirements for the grounding electrode.

Electrical energy can perform many useful functions. This

unit has been engineered and manufactured to assure

your personal safety. Improper use can result in potential

electrical shock or fire hazards. In order not to defeat the

safeguards, observe the following basic rules for its

installation, use and servicing.

1 Heed Warnings - All warnings on the appliance and in

the operating instructions should be adhered to.

2 Follow Instructions - All operating and use instructions

should be followed.

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

3 Water and Moisture - The appliance should not be used

near water - for example, near a bathtub, washbowl,

kitchen sink, laundry tub, in a wet basement, or near a

swimming pool, etc.

4 Carts and Stands - The appliance should be used only

with a cart or stand that is recommended by the manu-

facturer.

ANTENNA LEAD

IN WIRE

GROUND

CLAMP

ANTENNA DISCHARGE

UNIT

(NEC SECTION 810-20)

E L E C T R I C

S E R V I C E

EQUIPMENT

●

An appliance and cart combination

should be moved with care.

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

Quick stops, excessive force, and un-

even surfaces may cause the appli-

ance and cart combination to overturn.

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC - NATIONAL ELECTRICAL CODE

S2898A

13 Nonuse Periods - The power cord of the appliance

should be unplugged from the outlet when left unused

for a long period of time.

5 Wall or Ceiling Mounting - The appliance should be

mounted to a wall or ceiling only as recommended by

the manufacturer.

14 Object and Liquid Entry - Care should be taken so that

objects do not fall and liquids are not spilled into the

enclosure through openings.

15 Damage Requiring Service - The appliance should be

serviced by qualified service personnel when:

A The power-supply cord or the plug has been damaged;

6 Ventilation - The appliance should be situated so that

its location or position does not interfere with its proper

ventilation. For example, the appliance should not be

situated on a bed, sofa, rug, or similar surface that may

block the ventilation openings; or, placed in a built-in

installation, such as a bookcase or cabinet that may

impede the flow of air through the ventilation openings.

7 Heat - The appliance should be situated away from heat

sources such as radiators, heat registers, stoves, or

other appliances (including amplifiers) that produce

heat.

8 Power Sources - The appliance should be connected

to a power supply only of the type described in the op-

erating instructions or as marked on the appliance.

9 Power-Cord Protection - Power-supply cords should be

routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying

particular attention to cords at plugs, convenience re-

ceptacles, and the point where they exit from the appli-

ance.

B Objects have fallen, or liquid has been spilled into the

appliance; or

C The appliance has been exposed to rain; or

D The appliance does not appear to operate normally or

exhibits a marked change in performance; or

E The appliance has been dropped, or the enclosure dam-

aged.

16 Servicing - The user should not attempt to service the

appliance beyond that described in the operating in-

structions. All other servicing should be referred to quali-

fied service personnel.

17 Grounding or Polarization - Precautions should be taken

so that the grounding or polarization means of an ap-

pliance is not defeated.

10 Do not use liquid cleaners or aerosol cleaners. Use a

damp cloth for cleaning.

11 Power Lines - An outdoor antenna should be located

away from power lines.

0001

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTENTS

Page

MINIDISC EDITING ................................................... 26-31

TIMER OPERATION .................................................. 32-33

USING EXTERNAL UNITS ....................................... 34-35

WHAT IS A MINIDISC? .................................................. 36

MINIDISC SYSTEM LIMITATIONS ................................. 37

TROUBLESHOOTING ............................................... 37-38

RESETTING THE MICROCOMPUTER .......................... 38

ERROR MESSAGES ...................................................... 39

MAINTENANCE ............................................................. 40

SPECIFICATIONS .......................................................... 40

CONSUMER LIMITED WARRANTY ............... Back cover

ACCESSORIES ................................................................ 3

PRECAUTIONS ................................................................ 4

NAMES OF CONTROLS AND INDICATORS ................... 5-7

PREPARATION FOR USE........................................... 8-10

SETTING THE CLOCK ................................................... 11

SOUND CONTROL ........................................................ 12

COMPACT DISC OPERATION ....................................... 13

MINIDISC OPERATION .................................................. 14

CONVENIENT CD AND MINIDISC OPERATIONS ........... 15-18

RADIO OPERATION ................................................. 19-20

MINIDISC RECORDING ............................................ 21-25

ACCESSORIES

Remote control × 1

(RRMCG0208AWSA)

AC power cord × 1

(QACCD0025AWZZ)

AM loop antenna × 1

(QANTL0009AWZZ)

FM antenna × 1

(92LFANT1746A)

Speaker wire × 2

(92L291-0089)

Note:

Parts and accessories mentioned in this operation manual other than those in the drawing are not included.

Download from Www.Somanuals.com. All Manuals Search And Download.

PRECAUTIONS

■ Care of compact discs

■ General

● Please ensure that the equipment is positioned in a well

ventilated area and ensure that there is at least 4" (10cm)

of free space along the sides and back.There must also be

a minimum of 4" (10cm) of free space on the top of the

unit.

Compact discs are fairly resistant to damage, however

mistracking can occur due to an accumulation of dirt on the

disc surface.

Follow the guidelines below for maximum enjoyment from your

CD collection and player.

● Do not write on either side of the disc, particularly the non-

label side.

Signals are read from the non-label side. Do not mark this

surface.

● Keep your discs away from direct sunlight, heat, and ex-

● Do not use oil, solvents, gasoline, paint thinners or insecti-

cides on the unit.

● Do not expose the unit to moisture, to temperatures higher

than 140°F (60°C) or to extreme low temperatures.

● Keep the unit away from direct sunlight, strong magnetic

fields, excessive dust, humidity and electronic/electrical

equipment (home computers, facsimiles, etc.) which gen-

erate electrical noise.

cessive moisture.

● Always hold the CDs by the edges. Fingerprints, dirt, or

water on the CDs can cause noise or mistracking. If a CD

is dirty or does not play properly, clean it with a soft, dry

cloth, wiping straight out from the center, along the radius.

● Hold the AC power plug by the head when removing it from

the AC outlet, since pulling the cord can damage internal

wires.

● Do not remove the outer cover, as this may result in elec-

tric shock.

Refer internal service to your local SHARP service facility.

● Use the unit on a firm, level surface free from vibration,

and do not place anything on the top of the unit.

● If the unit malfunctions while in use, press the ON/STAND-

BY button to enter the stand-by mode, then disconnect the

AC power cord from the AC outlet. Plug the AC power cord

back in, and then press the ON/STAND-BY button to turn

the power on.

YES

● If an electrical storm is taking place near you, it is sug-

gested that you disconnect the AC power cord from the AC

outlet for safety.

Correct

■ Volume control

Warning:

The sound level at a given volume setting depends on a com-

bination of speaker efficiency, location and various other fac-

tors.

It is advisable to avoid exposure to high volume levels, which

occur while turning the unit on with the volume control setting

up high, or while continually listening at high volumes.

● The voltage used must be the same as that specified on

this unit.Using this product with a higher voltage other than

that which is specified is dangerous and may result in a fire

or other type of accident causing damage. SHARP will not

be held responsible for any damage resulting from use of

this unit with a voltage other than that which is specified.

■ Condensation

Sudden temperature changes, storage or operation in an ex-

tremely humid environment may cause condensation inside

the cabinet (CD pickup, MiniDisc pickup, etc.) or on the trans-

mitter LED on the remote control.

Condensation can cause the unit to malfunction.

If this happens, leave the power on with no disc in the unit

until normal playback is possible (about 1 hour).Wipe off any

condensation on the remote control transmitter LED with a

soft cloth before operating the unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

NAMES OF CONTROLS AND INDICATORS

■ Front panel

2 3 4

5 6 7 8

1. On/Stand-by Button

6. MD Stop Button

11. MD Eject Button

12. Jog Dial

13. Memory/Enter Button

2. Timer Stand-by Indicator

3. Name/TOC Edit Button

4. Timer/Delete Button

7. MD Play/Pause Button

8. Tuning Up/Cue Button

9. Display (Demo) Button

10. MD Compartment

5. Tuning Down/Review Button

15 16 17 18 19 20

22 23 24

25 26

14. CD Compartment

15. Record Button

18. CD Open/Close Button

19. CD Stop Button

20. CD Play/Pause Button

21. Headphone Jack

24. Extra Bass Button

25. Tuner (Band) Button

26. Auxiliary Button

16. CD

MD Normal Speed

Edit Button

27. Volume Control

17. CD

MD High Speed

22. Surround Button

28. Volume Select Button

Edit Button

23. Preset Equalizer Button

Download from Www.Somanuals.com. All Manuals Search And Download.

(Continued)

■ Display window

2 3 4 5 6

8 9

10 11

21 22 23 24

1. FM Stereo Indicator

2. FM Stereo Mode Indicator

3. Track Edit Indicator

4. Play/Pause Indicator

5. Repeat Indicator

11. MD Indicator

21. AM/PM Indicator

22. Timer Record/Timer Play Indica-

tor

23. Surround Indicator

24. Extra Bass Indicator

12. Record Indicator

13. Sleep Indicator

14. Disc Indicator

15. Track Indicator

16. Memory Indicator

6. TOC Indicator

7. Level Meters

8. Digital Recording Indicator

9. CD Indicator

17. Random Play Indicator

18. Total Time Indicator

19. Remaining Time Indicator

20. Character Information Display

10. High Speed Edit Indicator

■ Rear panel

1. FM 75 Ohms Antenna Terminal

2. Antenna Ground Terminal

3. AM Loop Antenna Terminal

4. Auxiliary Input Jacks

5. Speaker Terminals

3 4

6. AC Power Input Jack

Download from Www.Somanuals.com. All Manuals Search And Download.

(Continued)

■ Remote control

1. Remote Control Transmitter LED

2. Preset Equalizer Button

3. Surround Button

4. Clock Button

5. Sleep Button

6. Memory/Enter Button

7. MD Stop Button

8. MD Play/Pause Button

9. MD Track Down/Review Button

10. MD Track Up/Cue Button

11. Track Edit Button

12. Record Button

13. On/Stand-by Button

14. Dimmer Button

15. Tuner Preset Up/Down Buttons

16. Extra Bass Button

17. Volume Select Button

18. Display Button

19. Clear Button

20. Play Mode Button

21. Time Button

22. CD Play/Pause Button

23. CD Stop Button

24. CD Track Up/Cue Button

25. CD Track Down/Review Button

26. Tuner (Band) Button

27. Auxiliary Button

28. Volume Buttons

■ Speaker section

1. Tweeter

2. Woofer

3. Bass Reflex Duct

4. Speaker Terminals

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION FOR USE

Unplug the AC power cord from the AC outlet before

connecting or disconnecting any component.

Outdoor FM antenna

Use an outdoor FM antenna (75 ohm coaxial cable)

if you require better reception. Consult your dealer.

■ Antenna connection

Note:

● When an outdoor FM antenna is used, disconnect the sup-

plied FM antenna wire from the FM 75 OHMS terminal.

Outdoor AM antenna

Use an outdoor AM antenna if you need better reception.Con-

sult your dealer.

AM loop antenna

FM antenna

Note:

● When using an outdoor AM antenna, be sure to keep the

wire of the AM loop antenna connected.

■ Speaker connection

Black

Right

Red

Black

Red

Left

Outdoor AM

49 feet (15 m)

antenna

Outdoor FM

antenna

25 feet (7.5 m)

Ground rod

Ground wire

Black

Red

75 ohm

coaxial cable

Supplied FM antenna

Connect the FM antenna wire to the FM 75 OHMS terminal

and position the FM antenna wire in the direction where the

strongest signal can be received.

Connect each speaker wire to the SPEAKER terminals as

shown.

Use speakers with an impedance of 6 ohms or more, as lower

Supplied AM loop antenna

Connect the AM loop antenna wire to the AM and GND termi-

nals.

Position the AM loop antenna for optimum reception.Place the

AM loop antenna on a shelf, etc., or attach it to a stand or a

wall with screws (not supplied).

impedance speakers can damage the unit.

Caution:

● Before connecting the speakers to the unit, connect the

speaker wires to the speakers first. Then, connect the

speaker wires to the terminals on the unit.

● Connect the speakers to the main unit before you use the

system. If the speakers are not connected before opera-

tion, the system may be damaged.

Notes:

● When static is still heard even after adjusting the position of

the AM loop antenna, try reversing the wire connections.

● Do not place the AM loop antenna and the FM antenna wire

on the unit.It may result in noise generation, since the unit is

equipped with digital electronics.

Place the AM loop antenna and the FM antenna wire away

from the unit for better reception.

Notes:

● Connect the black wire to the minus (–) terminal, and the

red wire to the plus (+) terminal.

● Do not mix the right channel and left channel wiring when

connecting the speakers to the unit.

● Do not let bare speaker wires touch each other as this may

damage the amplifier and/or speakers.

● If the AM loop antenna and the FM antenna wire are placed

near the AC power cord, interference may result.

Download from Www.Somanuals.com. All Manuals Search And Download.

(Continued)

■ Connecting the AC power cord

■ Removing the speaker grilles

AC 120 V, 60 Hz

Remove the lower part of the speaker grille first.

Remove the upper part of the speaker grille.

To AC INPUT

Caution:

When the speaker grilles are removed, the speaker dia-

phragms are exposed. Make sure nothing comes into contact

with the speaker diaphragms.

To an AC outlet

Connect the AC power cord to the AC INPUT jack, then

connect its plug to an AC outlet.

■ Placing the system

Notes:

● Unplug the AC power cord from the AC outlet if the unit will

not be in use for a prolonged period of time.

4" (10 cm)

● Never use a power cord other than the one supplied. Use

of a power cord other than the one supplied may cause an

electric shock or fire.

■ Demo mode

4" (10 cm)

DISPLAY

(DEMO)

Be sure to keep space between the units for ventilation.

Keep the top and the back of this unit at least 4" (10 cm)

away from the wall.

When the AC power cord is first connected, the unit will

enter the demonstration mode and the words will scroll

across the display continuously.

To cancel the demonstration mode:

When in the demonstration mode, press the DISPLAY (DEMO)

button.

● The demonstration mode will be canceled and the unit

will be in the low power consumption mode.

Note:

● When the unit is in the low power consumption mode, the

display will disappear.

Download from Www.Somanuals.com. All Manuals Search And Download.

(Continued)

■ Remote control

■ To change the brightness of the display

2 "AA" size batteries

(UM/SUM-3, R6, HP-7

or similar)

●

Batteries are not included.

Remote

sensor

DIMMER

Lights up

When bright

8" - 20'

(0.2 m - 6 m)

Goes out

When dark

● When inserting or removing the batteries, push them

Press the ON/STAND-BY button to turn the power on.

Press the DIMMER button.

toward the battery terminal.

● Installing the batteries incorrectly may cause the unit

to malfunction.

● The display will become dimmer and the light around the

VOLUME control will go out.

Precautions for battery use:

● Insert the batteries according to the direction indicated in

the battery compartment.

To return to the original brightness:

Press the DIMMER button again.

● Replace all old batteries with new ones at the same time.

● Do not mix old and new batteries.

● Remove the batteries if they are weak or if the unit will not

be used for long periods of time.

This will prevent potential damage due to battery leakage.

Caution:

Do not use rechargeable batteries (nickel-cadmium battery,

etc.).

Notes concerning use:

● Replace the batteries if the operating distance is reduced

or if the operation becomes erratic.

● Periodically clean the transmitter LED on the remote con-

trol and the sensor on the main unit with a soft cloth.

● Exposing the sensor on the main unit to strong light may

interfere with operation. Change the lighting or the direc-

tion of the unit.

● Keep the remote control away from moisture, excessive

heat, shock, and vibrations.

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTING THE CLOCK

Adjust the hour by turning the jog dial.

MEMORY/

ENTER

ON/STAND-BY

● When the jog dial is turned one click clockwise, the time

will increase by 1 hour. When it is turned one click coun-

terclockwise, the time will decrease by 1 hour.

Jog dial

Keep turning the jog dial to change the time continuously.

● When the 12-hour display is selected, “AM” will change

automatically to “PM”.

Press the MEMORY/ENTER button.

Adjust the minutes by turning the jog dial.

CLOCK

● When the jog dial is turned one click clockwise, the time

will increase by 1 minute.When it is turned one click coun-

terclockwise, the time will decrease by 1 minute.

Keep turning the jog dial to change the time continuously.

● The hour setting will not advance even if minutes advance

from "59" to "00".

● In this example, the clock is set for the 24-hour (0:00) sys-

tem.

Press the MEMORY/ENTER button.

Press the ON/STAND-BY button to turn the power on.

Press the CLOCK button.

● The clock starts operating from "0" second.

(Seconds are not displayed.)

To see the time display:

Press the CLOCK button.

● The time display will appear for about 5 seconds even in

the stand-by mode.

Within 5 seconds, press the MEMORY/ENTER button.

Turn the jog dial to select the time display mode.

Note:

● The "CLOCK" will appear at the push of the CLOCK button

when the AC power supply is restored after a power failure

occurs or after the AC power cord is disconnected.

If this happens, follow the procedure below to change the

clock time.

To change the clock time:

"0:00"

→The 24-hour display will appear.

→(0:00 - 23:59)

Press the CLOCK button.

Within 5 seconds, press the MEMORY/ENTER button.

"12:00 AM" →The 12-hour display will appear.

→(AM or PM 12:00 - 11:59)

"0:00 AM" →The 12-hour display will appear.

→(AM or PM 0:00 - 11:59)

Perform steps 6 - 9 above.

To change the time display mode:

● Note that this can only be set when the unit is first in-

stalled or it has been reset (see page 38).

Reset the microcomputer (see page 38).

Perform steps 2 - 9 above.

Press the MEMORY/ENTER button.

Download from Www.Somanuals.com. All Manuals Search And Download.

SOUND CONTROL

■ Volume

■ Extra bass (X-BASS)

(Main unit)

(Remote control)

X-BASS

(Main unit)

X-BASS

MAX

(Main unit operation)

When the VOLUME control is turned clockwise, the vol-

ume will increase. When it is turned counterclockwise,

the volume will decrease.

Press the X-BASS button to emphasize the bass region

of the frequency spectrum.

● "X-BASS ON" will appear.

(Remote control operation)

Press the VOLUME button to increase the volume and

the VOLUME button to decrease the volume.

Press the X-BASS button again to cancel the extra bass

mode.

● "X-BASS OFF" will appear.

Servo Powered Volume:

Note:

● Turn the X-BASS to the off position when playing the unit

at high volume levels to avoid speaker distortion.

(Main unit)

(Remote control)

VOLUME

SELECT

■ Surround

(Remote control)

(Main unit)

SURROUND

The VOLUME control automatically comes out when the

power is turned on, and goes back when the unit is set to

the stand-by mode.

● When the power is turned on, you can put the VOLUME

control in and out by pressing the VOLUME SELECT but-

ton.

Note:

SURROUND

● Do not push in the VOLUME control forcibly with your fin-

ger as this may damage the unit.

■ Pre-programmed equalizer

(Remote control)

(Main unit)

EQUALIZER

Press the SURROUND button to widen the soundstage

and surround you with sound.

● "SURROUND" will appear.

Press the SURROUND button again to cancel the sur-

round mode.

● "PASS" will appear.

FLAT

SOFT

HEAVY

VOCAL

When the EQUALIZER button is pressed, the current

mode setting will be displayed. To change to a different

mode, press the EQUALIZER button repeatedly.

FLAT: The sound is not modified.

HEAVY: Bass and treble are emphasized.

VOCAL: Vocals (midrange tones) are emphasized.

SOFT: Treble is reduced.

Download from Www.Somanuals.com. All Manuals Search And Download.

COMPACT DISC OPERATION

■ CD playback

Press the ON/STAND-BY button to turn the power on.

Press the CD ■ button.

Press the 7 button to open the disc tray.

Place the CD on the disc tray, label side up.

3,5

● Be sure to place 3" (8 cm) CD in the middle of the disc

tray.

Press the 7 button to close the disc tray.

● The total number of tracks and the total playing time will

be displayed.

Total number of tracks

Total playing time

Label side up

Press the CD 06 button to start playback from track 1.

● When the last track has been played back, the unit will

stop automatically.

To interrupt playback:

Press the CD 06 button.

● “ 6 ” will appear.

● Press the CD 06 button again to resume playback from

the same point.

To stop playback:

Press the CD ■ button.

5" (12 cm)

3" (8 cm)

To remove the CD.

Press the 7 button.

After use:

Press the ON/STAND-BY button to enter the stand-by mode.

Caution:

● Do not carry the unit with a CD left in the disc tray.The

disc may come loose inside the unit and it may be dam-

aged or cause damage to the unit.This may also cause

malfunctions.

● Do not push the disc tray while it is moving.

● If the power fails while the tray is open, wait until the power

is restored.

● If the disc tray is stopped forcibly, "E-CD20" will appear in

the display and the unit will not function.

If this occurs, press the ON/STAND-BY button to enter the

stand-by mode and then turn the power on again.

●

Subjecting the unit to shock or vibration may cause mistracking.

Playing certain CDs at a high volume may cause mistracking.

In this case, listen at a lower volume.

● IfTV or radio interference occurs during CD operation, move

the unit away from the TV or radio.

Download from Www.Somanuals.com. All Manuals Search And Download.

MINIDISC OPERATION

■ MiniDisc playback

Press the ON/STAND-BY button to turn the power on.

Press the MD ■ button.

Load a MiniDisc in the direction indicated by the ar-

row on the MiniDisc, with the labeled side facing up.

● The disc name will be displayed only when the name has

been programmed onto the disc.

Label side up

Disc name

● The total number of tracks and the total playing time on

the MiniDisc will be displayed.

Total number of tracks

Total playing time

Press the MD 06 button.

● If the track name has been programmed on the MiniDisc,

it will appear and scroll across the display.

● If the MiniDisc has no track names, only the elapsed play-

ing time will appear.

● When the last track has been played back, the unit will

stop automatically.

To interrupt playback:

Press the MD 06 button.

● " 6 " will appear.

● Press the MD 06 button again to resume playback from

the same point.

To stop playback:

Press the MD ■ button.

To remove a MiniDisc:

Press the 7 button.

Caution:

● Do not carry the unit with a MiniDisc left in the MD

compartment.The disc may come loose inside the unit

and it may be damaged or cause damage to the unit.

This may also cause malfunctions.

● If TV or radio interference occurs when using the MiniDisc,

move the unit away from the TV or radio.

● Although MiniDiscs will not normally skip due to vibration,

you may hear skipping in the sound if there is continuous

vibration.

If the volume is turned up too high, sound skipping may

occur depending on the contents of the MiniDisc.

If this happens, turn the volume down and the skipping

should stop.

● If an error message is displayed during MiniDisc opera-

tion, see "ERROR MESSAGES" on page 39.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONVENIENT CD AND MINIDISC OPERATIONS

To listen again to the track being played:

(Main unit operation)

■ APSS (Auto Program Search System)

Turn the jog dial counterclockwise during playback.

MD 06

(Remote control operation)

Press the CD 5 or MD 5 button for less than 0.5 sec-

onds during playback.

jog dial

To move to the beginning of the next track:

(Main unit operation)

Turn the jog dial clockwise during playback.

CD 06

(Remote control operation)

Press the CD 4 or MD 4 button for less than 0.5 sec-

onds during playback.

● To skip a number of tracks at one time, turn the jog dial on

the main unit or press the CD 5 / 4 or MD 5 / 4

button on the remote control repeatedly until the desired

track number is shown.

● To start continuous playback from a desired track, select

the track number by turning the jog dial on the main unit, or

by pressing the CD 5 / 4 or MD 5 / 4 button on

the remote control, while in the stop mode.Then, press the

CD 06 or MD 06 button.

MD 06

CD 06

MD 5

CD 4

MD 4

CD 5

■ Cue and review

Load a disc and begin playback.

MD/CD 3 MD/CD 2

Hold the MD/CD 2 button down for audible fast for-

ward, and hold the MD/CD 3 button down for au-

dible fast reverse.

Normal playback will resume when the button is re-

leased.

Notes:

● When the end of the last track is reached, "END" will light,

and the unit will pause.

If you want to listen to a portion of a track again, press the

MD/CD 3 button to return to the point in the track you

want to listen to.

● If the beginning of the disc is reached while reviewing, play-

back will start automatically.

To search very quickly:

When fast forward or fast reverse is used while in the pause

mode, the playback point will move more quickly than when

using audible fast forward or audible fast reverse playback.

● In this mode, no sound is heard. Therefore, you should re-

fer to the time display.

● When you lift your finger, the unit will re-enter the pause

mode.

MD 3

CD 2

MD 2

CD 3

Download from Www.Somanuals.com. All Manuals Search And Download.

(Continued)

Repeat steps 3 and 4 for any other tracks. Up to 20

tracks (P-20) can be programmed.

■ APMS (Automatic Programmable Music

Selector)

6 (CD operation)

To complete programming, press the CD ■ button.

1,6 MD H

7 MD 06

2,4

(MiniDisc operation)

To complete programming, press the MD ■ button.

Total number of tracks Total playing time

CD 06

7 (CD operation)

1,6

To begin playback of your programmed selections,

press the CD 06 button to start playback of the pro-

grammed selections.

CD H

(MD operation)

CLEAR

To begin playback of your programmed selections,

press the MD 06 button to start playback of the pro-

grammed selections.

2,4

● After all of the programmed tracks have finished playback,

the unit will automatically stop.

1,6

CD H

MD H

To clear the programmed selections:

Press the CLEAR button while the “MEMORY” indicator is

flashing.

● Each time the button is pressed, one track will be cleared,

beginning with the last track programmed.

CD 06

MD 06

To cancel the APMS:

While the unit is stopped in the APMS mode, press the CLEAR

button to turn off the “MEMORY” display.

● The program contents will be erased.

1 (CD operation)

Press the CD H button.

● When you open the disc tray or eject a MiniDisc, the APMS

mode will be canceled.

(MiniDisc operation)

Press the MD H button.

To check which tracks are programmed:

While the unit is stopped in the APMS mode, turn the jog dial

or press the CD 5 / 4 or MD 5 / 4 button.

Press the MEMORY/ENTER button.

Turn the jog dial or press the CD 5 / 4 or MD 5

/ 4 button to choose the track number you wish to

program into memory.

Track number

Playback order

Adding tracks to the program:

If a program has been previously stored, the “MEMORY” indi-

cator will be displayed. Then follow steps 2 - 6 to add addi-

tional tracks.The new tracks will be stored after the last track

of the original program.

MEMORY

Selected track number

Notes:

● It is not possible to insert an additional track between pro-

grammed tracks that have already been entered.

Press the MEMORY/ENTER button.

● Programming and canceling are not possible during play-

back or in the pause mode.

MEMORY

Playback order

Download from Www.Somanuals.com. All Manuals Search And Download.

(Continued)

■ Repeat and random play

Repeat play

After the last track has been played, playback will return to

the first track and begin again.

Random play

When the CD 06 or MD 06 button is pressed, all of the

tracks will be played at random, and then playback will stop.

(The same track will not be played back twice.)

To cancel repeat or random play:

Press the P-MODE button until the " R " or "RANDOM" dis-

play disappears.

P-MODE

MD 06

CD 06

To repeat playback of selected tracks:

Enter the program for the tracks you want and start repeat

play.

You can program a single track and play it repeatedly

(refer to page 16).

Notes:

● If you press the CD 4 or MD 4 button during random

play, you can move to the next track. On the other hand,

the CD 5 or MD 5 button does not allow you to move

to the previous track.The beginning of the track being played

will be located.

● During APMS play, random play is not possible.

● When random or repeat play is selected during CD or

MiniDisc playback, random or repeat play will start at that

point.

Select the desired program source, CD or MiniDisc.

Press the P-MODE (play mode) button.

● When using repeat play, be sure to press the CD ■ or MD

■ button after you have finished listening. Otherwise, the

disc will play continuously.

● Each time this button is pressed, the mode will change in

the following order:

Repeat indicator

Random indicator

Disappears

Press the CD 06 or MD 06 button to start playback.

Download from Www.Somanuals.com. All Manuals Search And Download.

(Continued)

■ Switching the time display

■ Changing the display during MiniDisc

playback

Each time theTIME button is pressed during playback or when

in the pause mode, the display will change.

Each time the DISPLAY button is pressed during playback or

when in the pause mode, the display will change as described

below.

DISPLAY

TIME

DISPLAY

The elapsed playing time for the current track will be

displayed.

TRACK

No display

The remaining playing time for the current track will

be displayed.

REMAIN

The total remaining playing time for the disc from the

point being played at that time will be displayed.

The track name will be displayed.

TRACK

TOTAL

REMAIN

● When the MiniDisc does not have a track name, this dis-

play does not appear.

Notes:

● During random play, the total remaining playing time will

not be displayed.

The total number of tracks and the remaining record-

ing time will be displayed.

● Depending on a CD or MiniDisc to be played, the playing

time display may not match the total playing time which is

indicated on the CD or MiniDisc jacket, as the time be-

tween the tracks is not included.

Download from Www.Somanuals.com. All Manuals Search And Download.

RADIO OPERATION

Manual tuning:

■ Tuning

Press the TUNING (X or W) button as many times as re-

quired to adjust the frequency shown on the display to the

frequency of the desired station.

Auto tuning:

When the TUNING (X or W) button is pressed for more than

0.5 seconds, scanning will start automatically and the tuner

will stop at the first receivable broadcast station.

● When radio interference occurs during auto scan tuning,

auto scan tuning may stop automatically at that point.

● If a weak station signal is found during auto scan tuning,

the station will be skipped.

● To stop the auto tuning, press the TUNING (X or W) but-

ton again.

To receive an FM stereo transmission, press the

TUNER (BAND) button so that the "ST" indicator on

the display lights up.

2,3,5

● "j" will appear when an FM broadcast is in stereo.

● If the FM reception is weak, press the TUNER (BAND)

button so that the "ST" indicator goes out.

● The reception changes to monaural, the sound becomes

clearer.

2,3,5

After use:

Press the ON/STAND-BY button to enter the stand-by mode.

Notes:

● The last station tuned in will be recalled, even after chang-

ing the tuning band or the function, or after switching the

unit to the stand-by mode.

● If the unit's tuner interferes with the reception of a nearby

TV or radio, move the unit as far away from these items as

possible.

Press the ON/STAND-BY button to turn the power on.

Press the TUNER (BAND) button.

Press theTUNER (BAND) button to select the desired

frequency band (FM ST, FM or AM).

FM ST

Press the TUNING (X or W) button to tune into the

desired station.

Download from Www.Somanuals.com. All Manuals Search And Download.

(Continued)

To recall a memorized station:

■ Preset tuning

Turn the jog dial or press the PRESET (X or W) button for

less than 0.5 seconds to select the desired station.

● The stations (preset channel number, frequency and fre-

quency band) which have been stored in memory will ap-

pear in the display in numerical order, irrespective of the

frequency bands.

You can store up to 40 stations in memory (40 stations con-

sisting of any combination of AM and FM stations you like)

and recall them.

Backup function:

The backup function protects all station presets for a few hours

should there be a power failure or the AC power cord is re-

moved from the AC outlet.

2,4

■ Preset memory scan

The stations saved in the preset memory can be scanned

automatically.

PRESET

(X W)

2,4

CLEAR

MEMORY/

ENTER

To enter stations into memory:

Perform steps 1 - 5 in the "Tuning" section.

Press the MEMORY/ENTER button.

MEMORY

To scan the preset stations, press the PRESET (X or

Within 5 seconds, turn the jog dial or press the PRE-

SET (X or W) button to make the preset channel num-

ber flash in the display.

W) button for more than 0.5 seconds.

● The station preset number will flash and the programmed

stations will be tuned in sequentially, for 5 seconds each.

Press the PRESET (X or W) button again to stop the

memory scan at the desired station.

Note:

● Store the stations in memory, in order, starting with preset

channel 1.

When the preset memory does not have any stations stored

in it, the preset memory scan will not function.

When

is displayed, a station has already been stored

in this preset number memory.

To erase the memorized station:

Within 5 seconds, press the MEMORY/ENTER button

to store that station in the selected station preset num-

ber memory.

Recall the memorized station to be erased by turning

the jog dial or pressing the PRESET (X or W) button.

Press the CLEAR button.

MEMORY

● "MEMORY" and preset number will flash.

● If the "MEMORY" and preset number indicators go out

before the station is memorized, repeat the operation from

step 2.

Within 5 seconds, press the MEMORY/ENTER button.

Repeat steps 1-3 to erase other memorized stations.

Repeat steps 1 - 4 to set other stations, or to change a

preset station.

● When a new station is stored in the selected station pre-

set number memory location, the previously memorized

station in that location will be erased.

To erase all memorized stations:

When the unit is in the stand-by mode, hold down theTUNER

(BAND) and the MD ■ buttons, and then press the ON/

STAND-BY button.

● "PRESET CLR" will appear.

Download from Www.Somanuals.com. All Manuals Search And Download.

MINIDISC RECORDING

■ Differences from tape recordings

■ About track numbers

You cannot record music on the reverse side of a Mini-

Disc.

MiniDiscs are single sided and should only be inserted with

the correct side up in the direction of the arrow on the top of

the MiniDisc.

When recording from a CD

New track numbers will be created automatically

according to the original tracks (Synchro mark function).

First track

Second track Third track

Track A

Track B

Track C

Second

track

MiniDisc

First track

Third track

Track C

Track A

Track B

You don't need to search for the starting point at which

to record.

The unit automatically finds the point at which recording can

start. Recording will start from that point.

● When you record from a CD to a MiniDisc, the track num-

bers recorded on the MiniDisc may not match the track

numbers on the CD.

You can check the total or remaining recordable time (pos-

sible recording) before recording.

If this happens, correct the track numbers using the DI-

VIDE (page 29) and COMBINE (page 29) functions after

recording.

This lets you plan a recording session so that the last song

will not come to an abrupt end before it has finished.

Recordings cannot be made in the following situa-

tions.

■ Disc writing (TOC)

● If you try recording on a playback-only MiniDisc (commer-

cially available music MiniDisc).

The TOC (Table of Contents) is information on track numbers

and recording areas to allow the unit to recognize musical

selections or sounds.

The entire MiniDisc is controlled depending on thisTOC, which

enables the unit to find the beginning of a track quickly or to

automatically record in a vacant area.

● If a MiniDisc is protected against accidental erasure (page

36).

● If there is no more recording time left on the disc (page

37).

● When the "TOC FULL" message appears (page 39).

● If a disc's TOC has been damaged.

Notes:

● When recording important selections, be sure to make a

preliminary test to ensure that the desired material is be-

ing properly recorded.

● The VOLUME, X-BASS, EQUALIZER and SURROUND

controls can be adjusted during recording, with no effect

on the recorded signal.

Area for TOC (recording track Area for recording

the sound

numbers, track names, etc.)

When you start recording or editing, "TOC" will appear in the

display window.

This indicates that information in the TOC is now being

changed according to the recording or editing being per-

formed. (The changed TOC is not yet recorded on the

MiniDisc at this time.)

The TOC is recorded when

● you stop recording.

● you switch to another input source.

● you eject the MiniDisc.

● you enter the stand-by mode.

Do NOT unplug the power cord while the TOC is being re-

corded ("TOC" is flashing) and do NOT impart shock to the

unit. Otherwise, TOC will not be correctly recorded, and con-

sequently proper playback may not be possible.

Download from Www.Somanuals.com. All Manuals Search And Download.

(Continued)

To cancel the operation:

Before pressing the CD 0 MD EDIT (HIGH or NORMAL)

button, press the CD ■ button.

■ Recording from a CD onto a MiniDisc

(One-Touch Editing)

A CD can be recorded to a MiniDisc, starting from the first

track, with one-touch operation.

To stop recording:

Press the MD ■ button.

● Playback and recording will stop and the track numbers

will be written on the MiniDisc.

MD H

Caution:

● When a recording is made at high speed, the playback

sound will not be heard.

● Check whether recording is performed or not with the level

meters.

● You cannot adjust the sound volume."VOL HOLD" appears

when you adjust the sound volume while recording at high

speed.

● When a damaged CD is recorded at high speed, the unit

may stop while recording, or some noise or a drop out may

be recorded. In this case, record the CD at normal speed.

Notes:

● When the CD playing time is longer than the available

MiniDisc recording time, the recording process will not start

even when the CD 0 MD EDIT button is pressed.

Press the ON/STAND-BY button to turn the power on.

Press the CD ■ button.

Load a CD and a recordable MiniDisc.

● The total number of tracks and the total playing time on

the CD will be displayed.

Total number of

recordable tracks

(from the first track)

Available record-

ing time

Press the CD 0 MD EDIT (HIGH or NORMAL) button.

● Press the NORMAL button for actual speed, HIGH for high-

● To record as many tracks as are available, press the CD 0

MD EDIT button again.

speed recording.

Then, when the CD 0 MD EDIT button is pressed again,

recording will start. However, when the MiniDisc runs out

of space, "DISC FULL" will be displayed and the CD and

MiniDisc will stop.

REC

However, if the available recording time on the MiniDisc is

less than the length of the first track on the CD, recording

will not be performed.

● Recording will begin, starting from the first track of CD.

● After recording (all of the tracks that can be recorded), the

unit will stop automatically.

To check the remaining time available for record-

ing:

Press the MD ■ button.

Load a MiniDisc.

Press the DISPLAY button to find the time followed by

hyphen.

● The total number of tracks previously recorded and the

available remaining time will be displayed, the unit will re-

turn to the original display 4 seconds later.

Download from Www.Somanuals.com. All Manuals Search And Download.

(Continued)

■ Track editing from a CD onto a MiniDisc

Press the CD 0 MD EDIT (HIGH or NORMAL) button.

You can record several consecutive tracks, starting from the

first track of a CD, to a MiniDisc.

REC

MD H

● The CD loaded will be recorded in order, starting from the

first track.When a MiniDisc runs out of recording space or

when a CD has been completely recorded, the CD and

the MiniDisc will stop automatically.

● Recording will begin, starting from the first track of CD.

● Selected tracks will be recorded in order.

After the unit has finished recording the last track, record-

ing will stop automatically.

Note:

● If repeat play has been set, when you press the CD 0 MD

EDIT (HIGH or NORMAL) button, the repeat mode will be

canceled automatically, and track editing will start.

To stop recording:

Press the MD ■ button.

● Playback and recording will stop and the track numbers

will be written on the MiniDisc.

4,5

Press the ON/STAND-BY button to turn the power on.

Press the CD ■ button.

Load a CD and a recordable MiniDisc.

Press the TRACK EDIT button.

When selecting CD

T-EDIT

Press theTRACK EDIT button repeatedly to select the

last track number you want to record.

The last

track number

Total recording time

● If you select 21 tracks or more, "E. OVER" will be dis-

played.

Download from Www.Somanuals.com. All Manuals Search And Download.

(Continued)

■ APMS recording from a CD onto a MiniDisc ■ To record without using One-Touch Editing

MD H

Select tracks for APMS playback (page 16).

Load a recordable MiniDisc.

Press the CD 0 MD EDIT (HIGH or NORMAL) button.

● APMS playback will start, and recording will start auto-

matically.

MD H

● Programmed tracks will be recorded in order. After the

unit has finished recording the last track, recording will

stop automatically.

Note:

● If repeat play has been set, when you press the CD 0 MD

EDIT (HIGH or NORMAL) button, the repeat mode will be

canceled automatically, and APMS recording will start.

To stop recording:

Press the MD ■ button.

● Playback and recording will stop and the track numbers

will be written on the MiniDisc.

Load a CD and a recordable MiniDisc.

Press the ● REC button.

● The unit will enter the recording stand-by mode.

Press the CD 06 button.

To stop recording:

Press the MD ■ button.

● Recording will stop and the track numbers will be written

on the MiniDisc.

Download from Www.Somanuals.com. All Manuals Search And Download.

(Continued)

To stop recording:

Press the MD ■ button.

The recording will stop and the track number will be written

on the MiniDisc.

■ Recording from the built-in radio onto a

MiniDisc

MD ■

To record the track number while recording:

The recording is performed as a single track.

To identify different sections of a recording, you can increase

the track number at any point during the recording process.

To create a new track number while in the recording mode,

press the ● REC button.

● The track number will increase by one, and then the re-

cording will continue.

MD ■

Tune in to the desired station (pages 19 - 20).

Load a recordable MiniDisc.

Press the ● REC button.

● The unit will enter the recording stand-by mode.

Check the recordable time by pressing the DISPLAY

button.

Notes:

● Before recording an AM broadcast, enter the recording

stand-by mode, and then separate the AM loop antenna

from the main unit. Adjust it so that the AM broadcast can

be tuned in most clearly.

● During recording, you cannot change the station.

Press the MD 06 button.

Download from Www.Somanuals.com. All Manuals Search And Download.

MINIDISC EDITING

■ What the editing function can do

After entering all of the characters in the name, press

the NAME/TOC EDIT button.

You can create original discs using the MiniDisc editing func-

tion, on which you can change the order of the tracks and you

can create disc or track names.

● Playback-only MiniDiscs cannot be edited.

● The disc name will be recorded.

● Tracks (up to 255 tracks per disc) can be named. Since

track names are displayed when the beginning of each track

is located or during playback, you can quickly check the

name of each track.

To erase a disc name:

After performing steps 1 to 3.

Press the TIMER/DELETE button for 2 seconds or more.

● "NAME CLEAR" will flash.

■ To create a disc name

Press the MEMORY/ENTER button.

TIMER/DELETE

Notes:

2,6

● Up to 40 characters can be entered.

● This function cannot be used in the random play mode and

APMS play mode.

3,5

2,4

■ Type of characters used

Type of

characters

Characters (Symbols)

Capital letters

Symbols

(

)

Number of characters you can enter

● Disc names and track names

Press the MD ■ button.

Up to 40 characters (including spaces) can be entered for

each name.

If more than 40 characters are entered, "NAME FULL" will

appear.

● The total number of tracks and the total playing time on a

MiniDisc will appear.

Press the NAME/TOC EDIT button, and then select

"DISC NAME" using the jog dial.

● Total number of characters per MiniDisc

A total of approximately 1,700 characters can be used for all

of the disc and track names. If more than 1,700 characters

are entered, " TOC FULL" will appear.

While editing, the "TOC" indicator is displayed. This means

the edit results have not been recorded on the MiniDisc.

To record the results, select another input or set the unit to

the stand-by mode. During writing, the "TOC" goes out, all

editing changes will be recorded on the disc.

Within 10 seconds, press the MEMORY/ENTER button.

DISC

● The unit will enter the character input mode.

Select the character you want using the jog dial.

DISC

Press the MEMORY/ENTER button to enter the char-

acter.

DISC

● Repeat steps 4 to 5 above to enter the characters in the

name.

Download from Www.Somanuals.com. All Manuals Search And Download.

(Continued)

To erase a track name:

After performing steps 1 to 2.

■ To create a track name

Press the TIMER/DELETE button for 2 seconds or more.

● "NAME CLEAR" will flash.

TIMER/DELETE

1,5

Press the MEMORY/ENTER button.

Notes:

2,4

● Up to 40 characters can be entered.

● This function cannot be used in the random play mode and

APMS play mode.

● If you create a track name while recording the track, make

sure you finish entering the name before you finish record-

ing the track.

If the end of the recording is reached before you have en-

tered the complete name, only the characters entered be-

fore the recording ended will be recorded. To rename it,

see page 28.

During playback or in the pause mode, press the

NAME/TOC EDIT button.

Within 10 seconds, press the MEMORY/ENTER button.

TRACK

● The unit will enter the character input mode.

● The track you are listening to will be played repeatedly.

Select the character you want using the jog dial.

TRACK

Press the MEMORY/ENTER button to enter the char-

acter.

TRACK

● Repeat steps 3 to 4 above to enter the characters in the

name.

After entering all of the characters in the name, press

the NAME/TOC EDIT button.

● The track name will be recorded.

● The unit will return to normal playback.

Download from Www.Somanuals.com. All Manuals Search And Download.

(Continued)

■ To change disc names and track names

● To add a character:

(Example: To change "BET" to "BEST")

TIMER/DELETE

NAME/TOC EDIT

To change disc names, perform steps 1 - 3 on page 26.

To change track names, perform steps 1 - 2 on page 27.

MD ■

Press the 3 or 2 button to flash the character at

the place you want to add a letter.

MEMORY/

ENTER

DISC

Jog dial

● To cancel the operation, press the MD ■ button.

Select the character you want to add, using the jog

dial.Then, press the MEMORY/ENTER button.

DISC

● To delete a character:

(Example: To change "BESUT" to "BEST")

DISC

To change disc names, perform steps 1 - 3 on page 26.

To change track names, perform steps 1 - 2 on page 27.

Press the 3 or 2 button to flash the character to

erase.

● The selected character will be added, and the original

characters will move to the right by one.

DISC

After entering all of the characters in the name, press

the NAME/TOC EDIT button.

● To cancel the operation, press the MD ■ button.

Note:

● You cannot modify disc or track names created on other

equipment if they are over 40 characters.

In this case, erase the name and then enter a new name.

Press the TIMER/DELETE button.

DISC

● After this step, if you are not going to enter a character, go

to step 5.

Select the character you want to add, using the jog

dial.Then, press the MEMORY/ENTER button.

● The selected character will be added, and the original

characters will move to the right by one.

After entering all of the characters in the name, press

the NAME/TOC EDIT button.

Download from Www.Somanuals.com. All Manuals Search And Download.

(Continued)

■ Divide

■ Combine

A single track can be divided into two at any de-

sired position.

● The numbers of the tracks which come after the newly di-

vided track will be automatically increased by one.

Two consecutive tracks can be combined into one

track.

● The numbers assigned to the tracks following the com-

bined tracks will be decreased by one automatically.

MD ■

3,4

1,2

Play the track which you want to divide into two, and

press the MD 06 button at the point where you want

to divide the track.

While in the stop mode, select the second of the two

adjacent tracks you want to combine using the jog

dial.

Or start playing the second of the two tracks you want

to combine, and then press the MD 06 button.

Press the NAME/TOC EDIT button, and within 10 sec-

onds, select "DIVIDE" using the jog dial.

Press the NAME/TOC EDIT button, and within 10 sec-

onds, select "COMBINE" using the jog dial.

Within 10 seconds, press the MEMORY/ENTER button.

● To cancel the operation, press the MD ■ button.

Press the MEMORY/ENTER button again.

● To cancel the operation, press the MD ■ button.

Press the MEMORY/ENTER button again.

● The track is divided, and the unit is stopped at the begin-

ning of the second of the two tracks.

● The numbers of the tracks which come after the divided

track are automatically increased by one.

● The two tracks are combined, and the unit is stopped at

the beginning of the combined track.

● When a track has been given a name is divided, the two

new tracks will have the same name. If "TOC FULL" mes-

sage is seen, reduce unnecessary tracks recorded on the

disc to make enough space (page 37).

● The numbers assigned to the tracks following the com-

bined track are automatically decreased by one.

When both tracks have a name:

● When only the first track has a name → That name will be

used.

Notes:

● This unit can hold up to 255 tracks. However, even if the

number of tracks assigned has not reached 255, it might

not be possible to make any further divisions of tracks (page

37).

● When only the second of the two tracks has a name →

That name will be used.

● When both tracks have a name → The name of the first

track will be used. To rename it, see page 28.

● This function cannot be used in the random play mode and

APMS play mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

(Continued)

To combine two non-contiguous tracks:

(Example: the first and third tracks)

Move the third track to the second track using the MOVE func-

tion.

Then, combine the first and second tracks using the COM-

BINE function.

■ Move

A designated track can be moved to any desired

position.

● The numbers assigned to the tracks following the track

which is moved will be adjusted automatically.

Notes:

● Tracks recorded from analog inputs cannot be combined

with tracks recorded from CDs or MiniDiscs using the digi-

tal inputs.

● Tracks recorded in the stereo mode cannot be combined

with tracks recorded in the monaural long-play mode.

● Tracks where either track's recording time is less than 15

seconds may not be combined.

MD ■

● This function cannot be used in the random play mode and

APMS play mode.

3,5

1,2,4

While in the stop mode, select the track you want to

move using the jog dial.

Or start playing the track to be moved, and then press

the MD 06 button.

Press the NAME/TOC EDIT button, and within 10 sec-

onds, select "MOVE" using the jog dial.

Within 10 seconds, press the MEMORY/ENTER button.

Select the new track position using the jog dial.

● To cancel the operation, press the MD ■ button.

Press the MEMORY/ENTER button again.

● The track is moved, and the unit is stopped at the begin-

ning of the new track selected in step 4.

Notes:

● When a track has been moved, the other tracks which are

affected will be assigned new track numbers automatically.

● This function cannot be used in the random play mode and

APMS play mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

(Continued)

■ Erase

■ All Erase

All of the tracks you want to erase can be erased

at once.

● Once all of tracks have been erased, they cannot be re-

covered. Double-check the tracks before erasing them.

Tracks you want to erase can be erased one at a

time.

● Once a track has been erased, it cannot be recovered.

Double-check the track number before erasing it.

BLANK

MD ■

3,4

1,2

To erase tracks one at a time:

To erase all of the tracks at once:

While in the stop mode, select the track you want to

erase using the jog dial.

Or start playing the track to be erased, and then press

the MD 06 button.

Press the MD ■ button.

● The total number of tracks and the total playing time on a

MiniDisc will appear.

Press the NAME/TOC EDIT button, and within 10 sec-

onds, select "ALL ERASE" using the jog dial.

Press the NAME/TOC EDIT button, and within 10 sec-

onds, select "ERASE" using the jog dial.

Within 10 seconds, press the MEMORY/ENTER button.

● To cancel the operation, press the MD ■ button.

Press the MEMORY/ENTER button again.

● To cancel the operation, press the MD ■ button.

Press the MEMORY/ENTER button again.

● All of the track numbers and track names will be erased.

● The track is erased, and the unit is stopped at the begin-

ning of the next track.

Note:

● This function cannot be used in the random play mode and

APMS play mode.

Notes:

● When a track is erased, the numbers assigned to the tracks

following the erased track will be automatically decreased

by one.

● When a track is erased, the track name will be erased at

the same time.

● This function cannot be used in the random play mode and

APMS play mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

TIMER OPERATION

I Before setting the timer, make sure that the clock setting

is correct (page 11).

■ Timer playback/Timer recording

MEMORY/

TIMER

1,10

3 2 MD H

ENTER

Turn the jog dial to set the minute to start, and then

press the MEMORY/ENTER button.

Jog dial

2 CD H

I If the ending time is not set manually, it will automatically

be set for one hour after the starting time.

Turn the jog dial to set the hour to stop, then press

the MEMORY/ENTER button.

2 TUNER (BAND) 2 AUX

Before timer operation, the following preparations are required.

Load a CD and a recordable MiniDisc for timer recording or

● Preset the radio station that you want to record from or

listen to during timer playback.

●

Press the ON/STAND-BY button to turn the power on.

Turn the jog dial to set the minute to stop, then press

the MEMORY/ENTER button.

2 (To select timer playback source)

Press the CD ■, MD ■,TUNER (BAND) or AUX button.

(To select timer recording source)

Press the CD ■,TUNER (BAND) or AUX button.

PLAY

REC

3 (To select timer playback)

Press the TIMER/DELETE button to select the timer

playback mode.

Adjust the VOLUME control for the desired volume.

● Be careful not to turn the volume up too high.

PLAY

10 Press the ON/STAND-BY button to enter the stand-

by mode.

(To select timer recording)

● The TIMER indicator will light up.

Press the TIMER/DELETE button again to select the

timer recording mode.

11 When the timer start time is reached, timer playback

or timer recording will start.

REC

12 When the timer end time is reached, timer recording

will stop.

While "f PLAY" or "f REC" is flashing, press the

MEMORY/ENTER button.

Notes:

I The timer cannot control the component connected to the

auxiliary input jacks.

I When the CD or MiniDisc is played to the end, playback

will stop before the stop time.

If you wish to play to the stop time, set repeat play for the

CD or MiniDisc.

● Timer playback and timer recording cannot be set at the

Turn the jog dial to set the hour to start, and then press

the MEMORY/ENTER button.

same time using the timer.

Download from Www.Somanuals.com. All Manuals Search And Download.

(Continued)

To confirm the timer setting:

Press the TIMER/DELETE button once.

● The turn-on time, the turn-off time will be displayed.

Press the SLEEP button to select the time.

(Maximum: 2 hours - Minimum: 30 minutes)

The amount of sleep time can also be changed during the

sleep operation.

● 2 hours-30 minutes → 30-minute intervals

To cancel timer operation:

While in the timer stand-by mode, press the ON/STAND-

BY button to turn the power on.

Press the TIMER/DELETE button repeatedly to turn off

the timer, "f PLAY" or "f REC" will go out.

SLEEP

Caution:

In the following cases, the timer recording function will not

work.

● When a MiniDisc has not been inserted.

The unit will enter the stand-by mode automatically

after the preset sleep time has elapsed.

● When a playback-only MiniDisc is inserted.

● When the MiniDisc you inserted is protected against acci-

dental erasure.

To cancel the sleep operation:

Press the SLEEP button repeatedly. "0:00" will appear and

"SLEEP" will go out at the same time.

● The sleep operation will be canceled.

● When there is no recording space left on the MiniDisc you

have inserted (when the "TOC FULL" or "DISC FULL"

message appears).

To confirm the remaining sleep time:

Press the SLEEP button.

■ Sleep operation

Notes:

● Once the sleep time is set, it will remain the same duration

until the setting is changed.

● The sleep functions of this unit cannot be used to control

equipment connected to this unit.You must use the sleep

functions of the other equipment, if it has them.

SLEEP

■ Simultaneous sleep and timer operation

Perform steps 1 - 9 on page 42, "Timer playback/Timer

recording".

Perform steps 1 - 3 of the "Sleep operation" on this page.

ON/

STAND-BY

➀Timer playback (record) setting

➁Sleep timer setting

Timer playback

(record) start time

Desired time

30 minutes - 2 hours

The radio, CD and MiniDisc can all be turned off automati-

cally.

Sleep operation will

automatically stop.

End time

Play the desired sound source.

Press the SLEEP button.

SLEEP

● If you do not need to change the time, the unit will enter

the sleep mode automatically.

Download from Www.Somanuals.com. All Manuals Search And Download.

USING EXTERNAL UNITS

■ Connecting external units

Before connecting external units, set this unit to the stand-by mode and turn off the power to the external units.

The other MD/CD player

Commercially available cord

with 1/8" (3.5 mm) stereo

mini-plug and RCA plugs

To the output /

headphone jack

LEFT

RIGHT

To the analog

output jacks

LEFT

RIGHT

LEFT

RIGHT

● Red plug → To RIGHT

● White plug → To LEFT

Commercially available RCA cord

■ Headphones

Notes:

● Before plugging in or unplugging the headphones, make sure the volume level is reduced.

● Be sure your headphones have a 1/8" (3.5 mm) diameter plug and are between 16 ohms and 50 ohms impedance.

The recommended impedance is 32 ohms.

● When headphones are connected, the speakers are disabled automatically.

Adjust the VOLUME control for the desired headphone volume.

Download from Www.Somanuals.com. All Manuals Search And Download.

(Continued)

■ Listening to sound from an external unit

■ Manual recording

To listen to sound from an external unit connected to the AUX

input terminals:

You can start a recording manually while listening to play-

back from other external equipment (tape deck, tuner) con-

nected to the auxiliary input.

MD H

Press the ON/STAND-BY button to turn the power on.

Press the AUX button.

Press the ON/STAND-BY button to turn the power on.

Load a recordable MiniDisc.

Start playback on the external unit, and adjust the in-

put sound level using the 3 or 2 button.

Press the AUX button.

● Adjust the recording level so that the "OVER" indicator

Press the I REC button.

does not light at the maximum level.

OVER

Start playback on the external unit.

Adjust the recording level using the 3 or 2 but-

ton.

● Adjust the recording level so that the "OVER" indicator

does not light at the maximum level.

-2

OVER

Adjust the listening level using the VOLUME buttons

on the remote control or the VOLUME control on the

main unit.

-2

Press the MD 06 button.

To stop recording:

Press the MD ■ button.

Download from Www.Somanuals.com. All Manuals Search And Download.

WHAT IS A MINIDISC?

The disc is stored in a cartridge.You can handle it easily with-

out worrying about dust, fingerprints, etc. However, dust en-

tering the opening of the cartridge, dirt on the cartridge, warp-

ing, etc. may cause malfunctions. Please note the following.

■ Adaptive TRansform Acoustic Coding

[ATRAC]

The ATRAC (Adaptive TRansform Acoustic Coding) is a new

technology that is designed to eliminate the information in

sounds which you can not hear and to compress the remain-

ing sound data so that the recording uses about 1/5 of the

original sound information. Sound data is analyzed and

filtered to take advantage of psycho acoustic masking. The

acoustic quality of the sound is not impaired.

■ Handling the MiniDisc

Do not touch the disc directly!

Do not open the shutter or touch the disc directly.

If the shutter is opened forcibly, it may break.

Disc

■ Types of discs

Cartridge

Shutter

There are two types of discs: playback-only and recordable

types.

● Playback-only MiniDisc:

This type of MiniDisc is used for commercially available

prerecorded music.This is the same kind of optical disc as

CDs. Playback is performed using an optical pickup. (Re-

cording and editing are not possible.)

Where not to store discs:

Do not store discs in places with high temperatures or hu-

midity. Specifically, do not leave discs in places exposed to

direct sunlight or in cars with doors and windows closed. Do

not leave discs in places where sand can get into the car-

tridge easily (e.g. beaches).

A Shutter will be used on

only one side (back).

● Recordable MiniDisc:

This is a "raw disc" on which recording can be performed.

A magneto optical disc is used. Recordings are made us-

ing a laser and magnetic field. Repeated recording is pos-

sible.

■ To prevent recorded discs from being

erased accidentally

Slide the accidental erase prevention tab, located on the side

of the disc, in the direction indicated by the arrow.

● The disc will then be protected against accidental erasure.

Shutters will be used on

both sides.

● To add a recording to such a disc, slide the accidental erase

prevention tab back to its original position.

■ How to apply labels

Tab

When sticking a label on a MiniDisc cartridge, be sure to ob-

serve the following. If a label is not affixed properly, a

MiniDisc may become jammed in the unit such that it can not

be removed.

Protected against

accidental erasure

● Stick a label correctly to the specified area.

(Do not stick labels to areas other than the specified one.)

● Do not stick one label upon another.

● If a label is peeling off or starts to come

loose, replace it with a new one.

■ What is a MiniDisc?

● A MiniDisc is a 2-1/2" (64 mm) diameter disc which is stored

in a cartridge. MiniDiscs are easy to handle, compared to

CDs, because they are protected against dust and

scratches.

■ Shock Resistant Memory

During playback, approximately 10 seconds of information is

stored in the semiconductor memory. Therefore, even when

the pickup cannot read information for a second or two due to

an external shock, the sound continues without interruption

because the information stored in memory is output.

● Recording and playback use a digital system with a sound

quality that is similar to that found on CDs.

MiniDiscs cannot twist or stretch like tapes. The quality of

sound will not deteriorate.MiniDiscs are extremely durable.

● Never disassemble MiniDiscs.

Download from Www.Somanuals.com. All Manuals Search And Download.

MINIDISC SYSTEM LIMITATIONS

Even if the maximum recording time of a In the MD system, the delimiter of the recording area on a MiniDisc is

MiniDisc has not been reached, "TOC FULL" programmed in a TOC. If partial erasing, recording and editing are re-

may be displayed.

peated several times, TOC information will fill up, even though the number

of tracks has not reached the limit (255 tracks), and further recording will

be impossible. (If you use the all erase function, this MiniDisc can be used

from the beginning.)

Even if the maximum recording time of a If there is any flaw on the MiniDisc, that part is automatically excluded

MiniDisc has not been reached, "DISC FULL" from the space available for recording. Therefore, the recording time be-

may be displayed.

comes shorter.

Even if several short tracks are erased, the re- When the remaining recording time of a disc is displayed, short tracks

maining recording time may not show an in- less than 12 seconds long may not be included in the total.

crease.

Two tracks may not be combined in editing.

For MiniDiscs on which repeated recording and editing operations were

performed, the COMBINE function may not work.

A track recorded from a CD (digital recording) and a track recorded from a

radio or other equipment (analog recording) cannot be combined.

The total of the recorded time and time remain- A cluster (about 2 seconds) is normally the minimum unit of recording. So,

ing on a disc may not add up to the maximum even if a track is less than 2 seconds long, it will use about 2 seconds of

possible recording time.

space on the disc.Therefore, the time actually available for recording may

be less than the remaining time displayed.

If there are scratches on discs, those sections will be automatically avoided

(no recording will be placed in those sections). Therefore, the recording

time will be reduced.

If recorded tracks are fast reversed or fast for- A MiniDisc which has been recorded or edited repeatedly may skip during

warded, the sound may skip.

fast reverse or fast forward.

TROUBLESHOOTING

■ If a problem occurs

If this unit functions abnormally during operation, first check the following items. If the unit continues to function abnormally, or if an

abnormality appears other than listed below, set this unit to the stand-by mode and disconnect the AC power plug, then consult your

SHARP dealer or service personnel.

General

Symptom

Possible cause

Remedy

● The clock is wrong.

● Did a power failure occur?

● Try setting it again.

● When a button is pressed, the unit

does not respond.

● Set this unit to the stand-by mode

and then turn it back on.Then, retry

the operation.

● No sound is heard.

● Is the volume level is set to "0"?

● Are the headphones connected?

● Increase the volume level.

● Disconnect the headphones.

● Connect the wires securely.

●

Are the speaker wires disconnected?

● Radios make unusual noise or the

picture on theTV screen is distorted.

● When a radio or TV which uses an

indoor antenna is placed near the

unit, the picture on the TV screen

may be distorted or the radio may

not function properly.

● It is recommended that you use an

external antenna.

CD Playback

Symptom

Possible cause

Remedy

● Even though a disc has been loaded,

● The disc is loaded up-side down.

● Load the disc with the correct side

"NO DISC" is displayed.

up.

● The disc is very dirty.

● The disc does not satisfy the stan-

dards.

● Is the unit located near excessive

vibrations?

● Playback stops in the middle of a

track, or playback is not performed

properly.

● Clean the disc.

● Load the correct disc.

● Place the unit on a firm, level sur-

face free from vibration.

● Playback sounds are skipped.

● Remove the disc and leave the

power turned on. The unit should

function properly in about 1 hour.

● Has condensation formed inside the

unit?

Download from Www.Somanuals.com. All Manuals Search And Download.

(Continued)

MiniDisc recording and playback

Symptom

Possible cause

Remedy

● A recording cannot be made.

● Is the MiniDisc protected against

accidental erasure?

● Slide the accidental erase preven-

tion tab back to its original position.

● Did you try to make recording on a

● Replace it with a recordable disc.

● Put in another recordable disc with

recording space on it.

playback-only MiniDisc?

● Can you see the "DISC FULL" or

"TOC FULL" message in the display?

● Even though a disc has been loaded,

"NO DISC" or "CAN'T READ" is dis-

played.

● The disc is very dirty.

● Is the unit located near excessive

vibrations?

● Clean the disc.

● Place the unit on a firm, level sur-

face free from vibration.

● Playback sounds are skipped.

● Has condensation formed inside the

unit?

● Remove the disc and leave the

power turned on. The unit should

function properly in about 1 hour.

Radio reception

Symptom

Possible cause

Remedy

● Radios make unusual noise con-

secutively.

● The unit is placed near the TV or

● When the unit receives a radio

broadcast near aTV set, a computer

or a word-processor, it may pick up

noise. If this happens, move the unit

from the place where the noise is

picked up.

computer.

● The antenna direction is not placed

properly.

● Correct the antenna direction.

● Preset the channel again.

● Redo programming.

● The preset channel cannot be re-

called.

● Did you erase the programmed sta-

tion?

Remote control

Symptom

Possible cause

Remedy

● The remote control does not func-

tion or does not operate properly.

● The batteries (polarity) are not in-

● Insert properly.

● Replace the batteries.

● Operate it within a range of 8" (0.2

m) to 20' (6 m) and within an angle

of 15 ° to either side of center.

serted properly.

● The batteries inside the remote con-

trol are dead.

● The remote control is operated from

an incorrect distance or angle.

● Connect the AC power cord.

● The power cannot be turned on from

the remote control.

● Is the AC power cord plugged in?

RESETTING THE MICROCOMPUTER

If this product is subjected to strong external interference

(mechanical shock, excessive static electricity, abnormal sup-

ply voltage due to lightning, etc.) or if it is operated incor-

rectly, it may malfunction or the display may not function cor-

rectly. If such a problem occurs, do the following:

1,2

Press the ON/STAND-BY button to enter the stand-by

mode.

Press the ON/STAND-BY button while holding down

the SURROUND button and the TIMER/DELETE but-

ton.

● "ALL CLEAR" will appear.

Caution:

● The operation explained above will erase all data stored in

memory including clock and timer settings, and tuner,

MiniDisc and CD presets.

Download from Www.Somanuals.com. All Manuals Search And Download.

ERROR MESSAGES

When an error message is displayed, proceed as follows:

Error messages

BLANK MD

Meaning

● Nothing is recorded.

(Neither music nor disc name is recorded.)

Remedy

● For playback, replace it with a recorded Mini-

Disc.

CAN'T COPY

CAN'T READ

● You tried to record from a copy prohibited CD. ● Replace the CD.

● The disc is damaged.

● Replace it with another disc.

(

:Number or

● TOC information cannot be read.

● MiniDisc not specified.

● Erase the disc and try recording again.

symbol)

CAN'T EDIT

● A track cannot be edited.

● Change the stop position of the track and then

try editing it.

CAN'T REC

● Recording cannot be performed correctly due ● Re-record or replace the MiniDisc.

to vibration or shock in the unit.

CAN'T WRITE

● TheTOC information could not be created prop- ● Set this unit to the stand-by mode and try to

erly due to a mechanical shock or to scratches

on the disc.

write the TOC again. (Remove any source of

shock or vibration while writing.)

DISC FULL

E-CD 20

● The disc is out of recording space.

● Replace the disc with another recordable disc,

or erase some of the tracks on the disc to free

up recording space.

● The CD tray is not working properly.

● Set this unit to the stand-by mode and turn the

power on again.

E. OVER

● You chose 21 or more tracks for track editing. ● Decrease the number of tracks.

EDIT OVER

● There is no space to make CD editing on the

● Replace it with a disc that has enough time to

disc.

record.

Er-MD

● A MiniDisc is not working properly.

● Set this unit to the stand-by mode and turn the

(

:Number or

power on again.

symbol)

NAME FULL

● The number of characters for the disc name or ● Shorten the disc or track name.

track name exceeds 40.

NO DISC

● A MiniDisc has not been loaded.

● The MiniDisc data cannot be read.

● A CD has not been loaded.

● Load a MiniDisc.

● Reload the MiniDisc.

● Load a CD.

● The CD data cannot be read.

● Reload the CD.

NOT AUDIO

● The data recorded on this disc is not audio data. ● Select another track.

● Replace the disc.

PLAY MD

● You tried to record on a playback-only disc.

● Replace it with another recordable disc.

PROTECTED

● The disc is write protected.

● Move the write protection tab back to its origi-

nal position.

TEMP OVER

TOC FORM

● The temperature is too high.

● Set this unit to the stand-by mode and wait for

a while.

● TOC information recorded on the MD does not ● Replace it with another disc.

match the MiniDisc specifications or it cannot ● Erase the disc and try recording again.

be read.

(

:Number or

symbol)

TOC FULL

● There is no space left for recording track num- ● Replace it with another recordable disc.

bers.

TOC FULL 1

? DISC

● There is no space left for recording character ● Replace it with another recordable disc.

information.

● Erase the needless characters.

● The data contains an error.

● Replace it with another disc.

● MiniDisc not specified.

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

■ External care

■ Internal care

● Periodically wipe the cabinet with a soft cloth and a diluted

● In order to ensure proper operation of the CD player, pre-

ventative maintenance (cleaning of the laser pick-up lens)

should be performed periodically in order to keep the lens

dust-free. Lens cleaners are commercially available. Con-

tact your local CD software dealer for options.

soap solution, then wipe with a dirty cloth.

● Do not use chemically treated cleaning cloths or other

chemicals.

SPECIFICATIONS

As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for

product improvement without prior notice. The performance specification figures indicated are nominal values of produc-

tion units. There may be some deviations from these values in individual units.

● General

● Compact disc player section

Power source:

AC 120 V, 60 Hz

51W

Type:

Drawer type compact disc player

Power

consumption:

Signal readout:

Non-contact, 3-beam semiconductor

laser pickup

Dimensions:

Width; 8-1/2" (215 mm)

Height; 6-7/16" (162 mm)

Depth; 13-1/2" (342 mm)

Rotation speed: 200 - 500 rpm CLV, Approx.

Error correction: CIRC (Cross Interleave Reed-Solomon

Code)

Weight:

9.7 Ibs. (4.4 kg)

Quantization:

16-bit linear

Frequency

response:

● Amplifier section

20 - 20,000 Hz

Output power:

FTC 12 watts per channel minimum

RMS into 6 ohms from 60 Hz to 20 kHz

with no more than 10 % total harmonic

distortion

D/A converter:

1-bit D/A converter

Signal/noise ratio: 95 dB (1 kHz)

Dynamic range: 90 dB (1 kHz)

Wow and flutter: Unmeasurable

Output terminals: Speaker; 6 ohms

Headphones; 16 - 50 ohms

(recommended 32 ohms)

(less than 0.001% W. peak)

Input terminals: Auxiliary; 500 mV/47 k ohms

● Tuner section

Frequency range: FM; 87.5 - 108.0 MHz

AM; 530 - 1,720 kHz

● MiniDisc recorder section

Type:

MiniDisc recorder

Sensitivity:

FM; 2.5 µV (75 ohms unbalanced)

AM; 650 µV/m

Signal readout:

Non-contact, 3-beam semiconductor

laser pickup

Rotation speed: 400 - 900 rpm CLV, Approx.

● Speaker section

Error correction: ACIRC (Advanced Cross Interleave

Type:

2-way speaker system

Reed-Solomon Code)

[4" (10 cm) woofer and 2" (5 cm)

tweeter]

Quantization:

Coding:

20-bit linear (A/D converter)

ATRAC (Adaptive Transform Acoustic

Coding)

Maximum input

power:

30 W

Sampling

frequency:

Rated input

power:

44.1 kHz

15 W

Recording

method:

Impedance:

Dimensions:

6 ohms

Magnetic modulation

overwrite method

Width; 6-5/16" (160 mm)

Height; 11-1/16" (280 mm)

Depth; 7-5/16" (185.5 mm)

Frequency

response:

20 - 20,000 Hz

Weight:

4.4 Ibs. (2 kg)/each

D/A converter:

1-bit D/A converter

Wow and flutter: Unmeasurable

(less than 0.001% W. peak)

Signal/noise ratio: 95 dB (1 kHz)

Dynamic range: 90 dB (1 kHz)

Audio channel:

Stereo; 2 channels

Monaural; 1 channel (playback only)

(long-time recording mode)

Download from Www.Somanuals.com. All Manuals Search And Download.

MEMO

Download from Www.Somanuals.com. All Manuals Search And Download.

MEMO

Download from Www.Somanuals.com. All Manuals Search And Download.

CONSUMER LIMITED WARRANTY

SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the

“Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees

that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or

remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.

This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth

below nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper

voltage or other misuse, abnormal service or handling, or which has been altered or modified in design or construction.

In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and

provide proof of purchase to the servicer.

The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by

law. ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR

USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do

not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those

described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of

Sharp.

The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and

exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described

herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to

the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or

otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product

which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall

Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some

states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY

FROM STATE TO STATE.

Model Specific Section

Your Product Model Number & Description: MD-MX20 MD Compact Component System

(Be sure to have this information available when you need service

for your Product.)

Warranty Period for this Product:

Additional Item(s) Excluded from

Warranty Coverage (if any):

Where to Obtain Service:

One (1) year parts and labor from the date of purchase.

Non-functional accessories, supplies, and consumable items.

At a Sharp Authorized Servicer located in the United States.

To find a location of the nearest Sharp Authorized Servicer, call

Sharp toll free at 1-800-BE-SHARP.

Ship prepaid or carry in your Product to a Sharp Authorized

Servicer.

What to do to Obtain Service:

Be sure to have Proof of Purchase available. If you ship the

Product, be sure it is insured and packaged securely.

TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION,

CALL1-800-BE-SHARP.

SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07430-2135

9910

SHARP CORPORATION

Printed in Malaysia

A0002.YT

TINSE0306AWZZ

Download from Www.Somanuals.com. All Manuals Search And Download.

Shoprider Mobility Aid 858WM User Manual
Shure Headphones MX395 User Manual
Shure Microphone MX300 User Manual
Snapper Trimmer D20380 User Manual
Sony Car Stereo System D117 User Manual
Sony Stereo Receiver STR DE245 DE345 User Manual
Sony TV Video Accessories 4 170 060 121 User Manual
Subaru Robin Power Products Portable Generator RGD3310 User Manual
Sunbeam Toaster 3822 033 User Manual
SUPER MICRO Computer Security Camera 5015A EHF User Manual