Sharp Stereo System HT DD5000 User Manual

SM  
<P=001>  
MODEL  
HT-DD5000  
HOME THEATER SYSTEM  
OPERATION MANUAL  
Thank you for purchasing this SHARP product.  
To obtain the best performance from this product,  
please read this manual carefully.  
It will guide you in operating your SHARP product.  
Note:  
This equipment has been tested and found to comply with the limits  
for a Class B digital device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against  
harmful interference in a residential installation.  
FOR YOUR RECORDS  
For your assistance in reporting this unit in case of loss  
or theft, please record below the model number and serial  
number which are located on the rear of the unit.  
Please retain this information.  
This equipment generates, uses, and can radiate radio frequency en-  
ergy and, if not installed and used in accordance with the instructions,  
may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful interfer-  
ence to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try to  
correct the interference by one or more of the following measures:  
Model number ______________________________  
Serial number_______________________________  
Date of purchase____________________________  
Place of purchase ___________________________  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that  
to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Manufactured under license from Dolby Laboratories.  
"Dolby", "Pro Logic" and the double-D symbol are trade-  
marks of Dolby Laboratories. Confidential Unpublished  
Works. 1992-1997 Dolby Laboratories, Inc. All rights re-  
served.  
WARNING  
FCC Regulations state that any unauthorized changes or modifications  
to this equipment not expressly approved by the manufacturer could  
void the user’s authority to operate this equipment.  
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTENTS  
Page  
Page  
SET UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-20  
RADIO OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . 21-22  
HOW TO USE THE BUILT-IN TIMER . . . . . . . . . . . . 23-24  
HEADPHONES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24  
DESCRIPTION OF TERMINOLOGY . . . . . . . . . . . . . . . .25  
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26  
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26  
CONSUMER LIMITED WARRANTY . . . . . . . . Back cover  
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2  
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2  
PREPARATION FOR USE . . . . . . . . . . . . . . . . . . . . . . . 3-7  
EXTERNAL UNIT CONNECTION . . . . . . . . . . . . . . . . . 8-11  
SOUND CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12  
DOLBY DIGITAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13  
SURROUND EFFECT CONTROL . . . . . . . . . . . . . . . 14-15  
ACCESSORIES  
Remote control x 1  
FM antenna x 1  
(QANTW0001SJZZ)  
AM loop antenna x 1  
(QANTL0001SJZZ)  
(RRMCG0004SJSA)  
Sub woofer wire × 1  
(QCNWH0001SJZZ)  
Front speaker wire × 2  
(QCNWH0001SJZZ)  
Center speaker wire × 1  
Surround speaker wire × 2  
(QCNWH0002SJZZ)  
(QCNWH0001SJZZ)  
Note:  
Parts and accessories mentioned in  
this operation manual other than  
those in the drawing are not included.  
RCA cord x 1  
(QCNWG0003SJZZ)  
Coaxial digital cord x 1  
(QCNWG0004SJZZ)  
PRECAUTIONS  
General  
If the unit does not work properly while in use, disconnect  
the AC power cord from the AC outlet. Plug the AC power  
cord back in, and then set the POWER button on the  
main unit to ON.  
Please ensure that the equipment is positioned in a well  
ventilated area and ensure that there is at least 4" (10  
cm) of free space along the sides, top and back of the  
equipment.  
If an electrical storm is taking place near you, it is sug-  
gested that you disconnect the AC power cord from the  
AC outlet for safety.  
Do not use oil, solvents, gasoline, paint thinners or in-  
secticides on the unit.  
Do not expose the unit to moisture, to temperatures  
higher than 140˚F (60˚C) or to extreme low temperatures.  
Warning:  
Keep the unit away from direct sunlight, strong magnetic  
fields, excessive dust, humidity and electronic/electrical  
equipment (home computers, facsimiles, etc.) which gen-  
erates electrical noise.  
The voltage used must be the same as that specified on  
this unit. Using this product with a higher voltage other than  
which is specified is dangerous and may result in a fire or  
other type of accident causing damage. SHARP will not be  
held responsible for any damage resulting from use of this  
unit with a voltage other than that which is specified.  
Hold the AC power plug by the head when removing it  
from the AC outlet, since pulling the cord can damage  
internal wires.  
Volume control  
Do not remove the outer cover, as this may result in  
electric shock. Refer internal service to your local SHARP  
service facility.  
The sound level at a given volume setting depends on a  
combination of speaker efficiency, location and various other  
factors.  
It is advisable to avoid exposure to high volume levels, which  
occur while turning the unit on with the volume control setting  
up high, or while continually listening at high volumes.  
Use the unit on a firm, level surface free from vibration,  
and do not place anything on the top of the unit.  
If "ERROR" appears or no sound is heard, set the  
POWER button on the main unit to OFF. About 5 sec-  
onds later, turn the power back on.  
2
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION FOR USE  
Unplug the AC power cord from the AC outlet before con-  
necting or disconnecting any component.  
Speaker connection  
Wires to be used with each speaker  
For the front, center and  
sub woofer speakers  
For the surround speakers  
Black  
Black  
Black (with white line)  
Black (with white line)  
Length: Approx.  
393-3/4" (10 m)  
Length: Approx.  
98-7/16" (2.5 m)  
3
1
2
Connecting the speaker wires  
1
2
3
Hold the speaker wire release catch down.  
Insert the wire into the speaker terminal.  
Release the catch.  
Caution:  
When connecting the speakers to the unit, connect the wires  
to the speakers first, and then to the terminals on the unit.  
Front speakers  
Front speaker  
(Left)  
Front speaker  
(Right)  
Connect each front speaker wire to the FRONT SPEAKER  
A terminals as shown.  
Use speakers with an impedance of 8 ohms or more, as  
lower impedance speakers can damage the unit.  
Connect the black wire with the white line to the negative  
(–) terminal, and the black wire to the positive (+) termi-  
nal.  
Black  
Black  
Note:  
You can connect the speakers you have to the FRONT  
SPEAKER B terminals. The recommended impedance is  
8 ohms.  
Black (with white line)  
Black (with white lline) Black  
Center speaker  
Connect the center speaker wire to the CENTER SPEAKER  
terminals as shown.  
Use a speaker with an impedance of 8 ohms or more, as a  
lower impedance speaker can damage the unit.  
Connect the black wire with the white line to the negative  
(–) terminal, and the black wire to the positive (+) termi-  
nal.  
Black  
Black (with white lline)  
Black (with white lline) Black  
3
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(Continued)  
Sub woofer  
Connect the sub woofer wire to the SUB WOOFER terminals  
as shown.  
Use a speaker with an impedance of 8 ohms or more, as a  
lower impedance speaker can damage the unit.  
Connect the black wire with the white line to the negative  
(–) terminal, and the black wire to the positive (+) termi-  
nal.  
Black  
Black (with white line)  
Black (with  
white line)  
Black  
Surround speakers  
Connect each surround speaker wire to the SURROUND  
SPEAKER terminals as shown.  
Surround speaker  
(Left)  
Surround speaker  
(Right)  
Black  
Black  
Use speakers with an impedance of 8 ohms or more, as  
lower impedance speakers can damage the unit.  
Connect the black wire with the white line to the negative  
(–) terminal, and the black wire to the positive (+) termi-  
nal.  
Black (with white line)  
Black (with white line) Black  
Caution:  
Do not allow any objects to fall into or to be placed in  
Do not reverse the right channel and left channel wires  
the bass reflex openings.  
when connecting the speakers to the unit.  
Do not let bare speaker wires touch each other, as this  
Do not stand or sit on the speakers. If the speakers fall  
or collapse, you may be injured.  
may damage the amplifier and/or speakers.  
Note:  
The speaker grilles are not removable.  
4
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(Continued)  
Placing the speakers  
Center  
Front  
left  
Front  
right  
When you connect this unit to a DVD player playing a disc  
with the  
trademark, you can enjoy realistic, powerful  
sound by playing the soundtrack through 6 channels; the  
front left, front right, center, surround left, surround right and  
sub woofer speakers.  
Sub  
woofer  
The best sound will be achieved by placing each speaker  
the same distance from the listener. Arrange the speakers  
so that the layout is as close as possible to the diagram  
shown in this illustration.  
Front speakers  
Surround  
left  
Surround  
right  
For best performance, place the speakers as shown in the  
diagram to the left.  
Same distance  
Place a TV halfway between the front left and front right  
speakers.  
Front  
right  
Front  
left  
Center  
Center speaker  
It is recommended that the center speaker be placed be-  
tween the left and right front speakers.  
Example: When installed on the wall  
Surround speaker  
Sub woofer  
Place the sub woofer near one of the front speakers, and  
orient it toward the listener as much as possible.  
Wall  
23" - 35"  
(60 - 90 cm)  
Surround speakers  
The surround speakers can be used by installing them on  
the wall or on stands. Install them 23" - 35" (60 - 90 cm)  
above the height of your ears when seated, if possible.  
Example: When installed vertically  
Note:  
The front speakers, center speaker, and sub woofer are  
magnetically shielded. The front speakers and sub woofer  
may be used by the sides of the TV. The center speaker  
may be used on top of the TV. However, some color variation  
may occur, depending on the type of TV used.  
If color variations occur ....  
Turn off the TV (from the power switch). After 15 - 30 min-  
utes, turn the TV on again.  
If the color variation is still present ....  
Move the speakers further away from the TV.  
3/32" (2.7 mm)  
5/32" (3.8 mm)  
To mount the surround speakers on the  
Min. 9-27/32" (25 mm) 9/32" (7 mm)  
wall  
5/32" (4 mm)  
The design of the surround speakers allows them to be hung  
on the wall.  
1
2
Be sure to use the screw type and size shown to the left.  
Min. 8-1/4" (21 mm)  
Wall surface  
Wall mounting screw  
1
Drive one screw into the wall for each speaker as shown  
in the illustration.  
Make sure that both the screw and the wall can support  
a load of 45 lbs. (20 kg).  
Drive the screws, so there is about a 5/32" (4 mm) space  
between the wall and the head of the screw.  
The screw is not included.  
Wall surface  
2
Mount the surround speaker on the wall so that the screw  
head is inserted into the slot on the surround speaker.  
5
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(Continued)  
Remote control  
When inserting or removing the batteries, push them to-  
ward the  
battery terminal.  
Installing the batteries incorrectly may cause the unit to  
malfunction.  
2 "AA" size batteries  
(UM/SUM-3, R6,  
HP-7 or similar)  
The batteries are not included.  
Precautions for battery use:  
Insert the batteries according to the direction indicated in  
the battery compartment.  
+
Replace all old batteries with new ones at the same time.  
-
Do not mix old and new batteries.  
+
Remove the batteries if they are weak or if the unit will  
not be used for long periods of time. This will prevent  
potential damage due to battery leakage.  
-
Caution:  
Do not use rechargeable batteries (nickel-cadmium battery,  
etc.).  
Notes concerning use:  
Replace the batteries if the operating distance is reduced  
8" - 20’  
(0.2 m - 6 m)  
or if the operation becomes erratic.  
Periodically clean the transmitter LED on the remote con-  
trol and the sensor on the main unit with a soft cloth.  
15˚  
15˚  
Exposing the sensor on the main unit to strong light may  
interfere with operation. Change the lighting or the direc-  
tion of the unit.  
Keep the remote control away from moisture, excessive  
heat, shock, and vibrations.  
SHARP TVs, VCRs and DVDs which are equipped with re-  
mote control can be controlled with button groups (A), (B)  
and (C).  
(A)(B)(C)  
Some TV and VCR models may not have some functions.  
Please refer to the TV’s, VCR’s and DVD’s operation manual.  
The remote control may not funciton with some TV and VCR  
models.  
(A)  
(B)  
(C)  
For details consult your nearest SHARP dealer or service  
center.  
6
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(Continued)  
Antenna connection  
1
3
2
Supplied FM antenna  
Connect the FM antenna wire to the FM 75 OHMS terminal  
and position the FM antenna wire in the direction where the  
strongest signal can be received.  
AM loop  
antenna  
Supplied AM loop antenna  
FM antenna  
Connect the AM loop antenna wire to the AM and GND  
terminals. Position the AM loop antenna for optimum recep-  
tion.  
Place the AM loop antenna on a shelf, etc., or attach it to  
a stand or wall with screws (not supplied).  
Notes:  
If you still hear static even after adjusting the position of  
the AM loop antenna, try reversing the wires or turn off  
the power to any external unit not in use.  
3
1
2
Do not place the antenna wires on the unit. It may result  
in noise generation, since the unit is equipped with digital  
electronics.  
Place the AM loop antenna and the FM antenna wire  
away from the unit for better reception.  
If the antenna wires are placed near the AC power cord,  
they may cause interference.  
49 feet (15 m)  
Outdoor AM  
antenna  
Outdoor  
FM antenna  
Outdoor FM antenna  
Use an outdoor FM antenna (75 ohm coaxial cable) if you  
require better reception.  
Consult your dealer.  
25 feet (7.5 m)  
Note:  
Ground rod  
When an outdoor FM antenna is used, disconnect the sup-  
plied FM antenna wire from the FM 75 OHMS terminal.  
Outdoor AM antenna  
Use an outdoor AM antenna if you need better reception.  
Consult your dealer.  
75 ohm coaxial  
cable  
Note:  
When using an outdoor AM antenna, be sure to keep the  
wire of the AM loop antenna connected.  
Ground wire  
Connecting the AC power cord  
After connecting the speakers and antennas, plug the AC  
power cord into a convenient AC outlet.  
AC OUTLET  
Note:  
AC 120 V, 60 Hz  
Unplug the AC power cord from the AC outlet if the unit  
will not be in use for a prolonged period of time.  
Unswitched AC Outlet  
Used to plug in the AC power plug from other equipment.  
The power consumption of any units connected to this outlet  
should not exceed a total of 120 W. The power to any equip-  
ment connected to this outlet is not switched by the POWER  
switch on the HT-DD5000.  
To an AC  
outlet  
7
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXTERNAL UNIT CONNECTION  
Cords required to connect an external unit  
The following cords are available to connect an external unit.  
Cord included with this unit  
Optional cord  
Coaxial digital cord  
RCA cord  
Optical digital cable  
Video cord  
When connecting the unit to a DVD player  
When connecting an audio signal using an optical digital cable  
To the audio (line) output jacks  
DVD player  
To the video output jack  
To the audio (digital) output jack  
To the video input jack  
TV  
When connecting an audio signal using a coaxial digital cord  
To the audio (line) output jacks  
DVD player  
To the video output jack  
To the audio (digital) output jack  
To the video input jack  
TV  
Caution: A DVD player allows you to select the "PCM" or "DOLBY DIGITAL" audio output mode. Before playing a Dolby  
digital sound disc, be sure to set the unit in the "DOLBY DIGITAL" mode. For more details, see the operation  
manual for your DVD player.  
8
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(Continued)  
When connecting the unit to a VCR or a camcorder  
To the audio output jacks  
VCR  
To the audio input jacks  
TV  
To the video output jack  
To the video input jack  
To the video  
input jack  
Camcorder  
To the audio output jacks  
To the video output jack  
VCR  
When connecting the unit to a tape deck or an MD deck  
To the audio output jacks  
MD deck  
To the audio input jacks  
9
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(Continued)  
When connecting the unit to a stereo turntable or a CD player  
CD player  
To the audio output jacks  
Stereo turntable  
How to switch audio signals and video sig-  
nals  
When the function button is pressed, a different input signal  
can be selected.  
To select the unit connected to the CD/AUX jacks  
Press the CD/AUX button.  
To select the unit connected to the DVD jacks  
To select the unit connected to the MD/TAPE jacks  
Press the DVD button.  
Press the MD/TAPE button.  
To select the unit connected to the VCR 1 jacks  
To select the unit connected to the PHONO jacks  
Press the VCR 1 button.  
Press the PHONO button.  
To select the unit connected to the VCR 2 jacks  
Press the VCR 2 button.  
Note:  
When a function other than DVD, VCR 1 or VCR 2 is se-  
lected, the video monitor output is not available.  
How to turn the power on or off  
POWER  
STAND-BY  
1
Set the POWER button on the main unit to ON.  
The STAND-BY indicator will light up and the power will  
be on.  
2
3
As long as the STAND-BY indicator is lit, you can turn  
the power on or put the unit in the stand-by mode, using  
the POWER button on the remote control.  
When through using this unit, set the POWER button on  
the main unit to OFF.  
POWER  
The STAND-BY indicator will go out.  
10  
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(Continued)  
Front speaker selector  
Select the front speakers you want to use.  
SPEAKERS  
A
B
Before selecting the switches, be sure to set the VOL-  
UME control to 0.  
OFF  
ON  
To listen using the "A" speakers:  
Set the SPEAKERS A button to ON.  
Sound will also be heard from the center, sub woofer and  
surround speakers.  
To listen using the "B" speakers:  
Set the SPEAKERS B button to ON.  
No sound will be heard from the center, sub woofer or  
surround speakers.  
To listen using both the "A" and "B" speakers:  
Set the SPEAKERS A and B buttons to ON.  
To stop the sound from all of the speakers:  
Set the SPEAKERS A and B buttons to OFF.  
To use headphones, set both buttons to OFF.  
Note:  
If either pair of the speakers, A or B, are connected to  
this unit, when both the SPEAKER A and B buttons are  
select to ON, no sound will be heard from the front speak-  
ers. Set the button for the speakers which you have con-  
nected to this unit to ON.  
SOUND CONTROL  
Volume  
(Main unit)  
(Remote control)  
(Main unit operation)  
VOLUME  
VOLUME  
When the VOLUME control is held in the + position, the  
volume will increase. When it is held in the position, the  
volume will decrease.  
(Remote control operation)  
0
1
2
79 80  
Press the VOLUME button to increase the volume and  
button to decrease the volume.  
the VOLUME  
Note:  
If you were listening at a volume of "71" or louder before  
turning the power off, when the power is turned on next time,  
the volume will be set back automatically to "70".  
Muting  
(Remote control operation)  
MUTE  
Press the MUTE button to mute the sound immediately.  
"MUTE" will flash.  
Press the MUTE button again to switch the sound back up  
to its previous volume level.  
11  
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(Continued)  
Extra bass (X-BASS)  
(Main unit)  
X-BASS  
(Remote control)  
(Main unit/remote control operation)  
Press the X-BASS button to emphasize the bass region of  
the frequency spectrum. To cancel the extra bass mode,  
press the X-BASS button. "X-BASS" will go out.  
X-BASS  
Pre-programmed equalizer  
1
(Main unit operation)  
1
Press the EQUALIZER button.  
The current mode setting will be displayed.  
2
Within 3 seconds, turn the jog dial to change to a different  
mode.  
FLAT  
HEAVY 1  
HEAVY 2  
2
3
SOFT 2  
SOFT 1  
3
Within 5 seconds, press the ENTER button.  
(Remote control operation)  
When the EQUALIZER button is pressed, the current mode  
setting will be displayed. To change to a different mode,  
press the EQUALIZER button repeatedly.  
EQUALIZER  
FLAT  
HEAVY 1  
HEAVY 2  
SOFT 2  
SOFT 1  
FLAT: The sound is not modified.  
HEAVY 1: Bass and treble are slightly emphasized.  
HEAVY 2: Bass and treble are emphasized more.  
SOFT 1: Treble is cut a little.  
FLAT  
HEAVY 1  
HEAVY 2  
SOFT 2  
SOFT 1  
SOFT 2: Treble is reduced a lot.  
Note:  
When the equalizer mode is being used, the Dolby Pro Logic  
Surround mode is canceled.  
Sub woofer output level  
(Remote control operation)  
When the SUB WOOFER LEVEL (  
/
) button is pressed,  
the sub woofer output level can be changed.  
SUB WOOFER  
LEVEL (  
)
-10 9  
+9 +10  
12  
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DOLBY DIGITAL  
When you connect this unit to a DVD player which is playing  
a disc with the trademark, you can enjoy realistic,  
DVD  
powerful sound by playing back the recorded signal through  
6 speakers with the sound coming from the front left, front  
right, center, surround left, surround right and sub woofer  
speakers.  
To listen to a disc using the Dolby Digital mode:  
1
2
Connect a DVD player. (See page 8.)  
Press the DVD button.  
The current DVD input channel will be displayed. If the  
DVD button is pressed while the current DVD channel is  
displayed, the input channel (ANALOG, COAXIAL, OPTI-  
CAL) can be changed.  
DVD  
3
Start the DVD player.  
Note:  
When the Dolby Digital surround mode is being used, the  
equalizer will be set to FLAT.  
Type of Dolby digital signal  
There are different types of Dolby digital signals. When you select COAXIAL or OPTICAL for the DVD input channel, the  
following items will be displayed for 2 seconds. They will also be displayed when the DVD player is operating and the DVD  
button is pressed.  
Display  
Channels available  
Display  
Channels available  
Normal PCM playback  
Front (L, R) + surround  
(L, R)  
DIGITAL  
Center only (monaural)  
Front (L, R) + center  
DIGITAL  
DIGITAL  
Front (L, R)  
Front (L, R) + center +  
surround (monaural)  
(When the surround mode  
is set to Normal, Phantom  
or Wide sound will also be  
heard from the surround  
speakers.)  
DIGITAL  
DIGITAL  
Front (L, R) + surround  
(monaural)  
Front (L, R) + center +  
surround (L, R)  
DIGITAL  
DIGITAL  
If a low frequency sound effect (Low Frequency Effect) contains a Dolby digital signal, "LFE" will light in the display.  
When this "LFE" is lit, low frequency signals will be output from the sub woofer.  
When Dolby digital signals are input, the display will light up  
or go out, as shown to the left.  
The channel speaker and SW indicators are used to set the  
sound for listening in the surround mode and will light up  
according to the speaker signals that are present.  
Lights up if the input contains a left channel signal.  
Lights up if the input contains a center channel signal.  
Lights up if the input contains a right channel signal.  
Lights up if the input contains an "LFE" signal.  
Lights up when the amplifier setting will output sound to  
sub woofer.  
Lights up if the input contains a left surround signal.  
Lights up if the input contains surround signals.  
Lights up if the input contains a right surround signal.  
➆ ➇  
13  
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SURROUND EFFECT CONTROL  
This product allows you to enjoy 3 surround modes.  
Normal mode/Wide mode:  
When you play a sound source that has the  
Phantom mode:  
When you play a sound source that has the  
(5.1 channels) or  
surround sound using all 6 speakers.  
trademarks, you can enjoy  
or  
trademarks, you can enjoy surround sound  
using 5 speakers, but not the center speaker.  
NORMAL/PHANTOM/WIDE mode  
3
2
When you connect this unit to other equipment (DVD player,  
LD player, video etc.) which is playing sound sources that  
have the  
or  
trademarks, you can  
enjoy Dolby surround sound.  
To listen to Normal/Phantom/Wide mode:  
4 5  
1
2
Connect the unit you want to play.  
Press the DVD button to select the DVD input from the  
jack you connected in step 1.  
(Main unit operation)  
3
4
Press the DOLBY SURROUND button.  
Within 3 seconds, turn the jog dial to select the Dolby  
Pro Logic Surround mode.  
2
3
STEREO NORMAL  
WIDE  
PHANTOM  
5
6
Within 5 seconds, press the ENTER button.  
Play the video software program.  
(Remote control operation)  
3
4
Press the DOLBY SURROUND button.  
Within 3 seconds, press the DOLBY SURROUND button  
repeatedly to select the Dolby Pro Logic Surround mode.  
STEREO NORMAL  
WIDE  
PHANTOM  
5
Play the video software program.  
Note:  
When the Normal/Phantom/Wide mode is being used, the  
equalizer will be set to FLAT.  
14  
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(Continued)  
NORMAL:  
NORMAL/WIDE  
For a stereo 2 channel input or a Dolby digital 2/0 input,  
sound will be output from the front left, front right, center  
and surround speakers. The same monaural channel will  
be output from the left and right surround speakers.  
Center speaker  
Front speaker  
(Right)  
Front speaker  
(Left)  
For a Dolby digital 5.1 channel input, sound will be output  
from the front left, front right, center, sub woofer, surround  
left and surround right speakers.  
Sub  
woofer  
If the surround signal only contains 1 channel, the same  
monaural channel will be output from the left and right  
surround speakers.  
For a Dolby digital 1/0 input, sound will only be output  
Surround  
(Left)  
Surround  
(Right)  
from the center speaker.  
WIDE:  
PHANTOM  
Select the WIDE mode if you have a large center speaker.  
With the WIDE mode, you can take full advantage of Dolby  
Pro Logic Surround sound.  
Front speaker  
(Right)  
Front speaker  
(Left)  
PHANTOM:  
Sub  
woofer  
The difference between this mode and the normal mode is  
that no sound is output from the center speaker.  
The center speaker signal is split equally and added to the  
sound for the front left and front right speakers.  
Surround  
(Right)  
Surround  
(Left)  
STEREO:  
Cancel the surround mode. Sound will only be output from  
the front left and front right speakers.  
STEREO  
For a Dolby digital multichannel input, any center or rear  
Front speaker  
(Right)  
Front speaker  
(Left)  
signals will be mixed and output from the front speakers.  
For a Dolby digital 1/0 input, monaural sound will be out-  
put from the front speakers.  
Sub  
woofer  
Preset balance  
(Remote control operation)  
While you are listening to music in any of the Dolby Pro  
Logic Surround modes (NORMAL, PHANTOM, WIDE), you  
can change the apparent position of the sound coming from  
the speakers to any position which has been stored in the  
memory of this unit.  
1
Press the PRESET BALANCE button.  
The current mode setting will be displayed.  
2
To change to a different mode, press the PRESET BAL-  
ANCE button repeatedly.  
PRESET  
BALANCE  
CENTER: More pronounced sound is heard from the center.  
BACK: More sound is heard from the rear.  
FRONT: More sound is heard from the front.  
3
The speaker level setting (see page 18) lets you change  
the center level or the surround level.  
Notes:  
If you turn off the power or press the PRESET BALANCE  
button, the center level or the surround level settings will  
be returned to their original levels.  
The initial setting of this product is in the CENTER posi-  
tion.  
15  
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SET UP  
Speaker size setting  
1
2
Press the MENU button repeatedly to make "SP SIZE"  
appear.  
Within 10 seconds, press the ITEM button to make  
"FRONT-SP" appear.  
The front speaker indicators will flash.  
MENU  
ITEM  
3
Within 10 seconds, press the SET UP ( or ) button  
to select "LARGE" or "SMALL".  
SET UP  
LARGE: When the front speakers can reproduce low fre-  
quencies (speakers which can reproduce sounds  
lower than 60 Hz)  
SMALL: When the front speakers cannot reproduce ex-  
tremely low frequencies  
4
Within 10 seconds, press the ITEM button to make  
"CENT-SP" appear.  
DIGITAL  
1
The center speaker indicators will flash.  
5
Within 10 seconds, press the SET UP ( or ) button  
to select "LARGE", "SMALL" or "SP-NO".  
DIGITAL  
DIGITAL  
LARGE: When the center speaker can reproduce low fre-  
quencies (speakers which can reproduce sounds  
lower than 60 Hz)  
2
3
SMALL: When the center speaker cannot reproduce ex-  
tremely low frequencies  
2 seconds  
DIGITAL  
NO:  
When no speaker is connected (When NO is se-  
lected, the indicator for that speaker position will  
go out.)  
DIGITAL  
DIGITAL  
6
Within 10 seconds, press the ITEM button to make  
"SURR-SP" appear.  
The surround speaker indicators will flash.  
4
5
7
Within 10 seconds, press the SET UP ( or ) button  
to select "SP-YES" or "SP-NO".  
2 seconds  
DIGITAL  
YES:  
NO:  
When the speakers are connected  
When no speaker is connected (When NO is  
selected, the indicator for that speaker position  
will go out.)  
DIGITAL  
8
Within 10 seconds, press the ITEM button to make "S-  
WOOFER" appear.  
DIGITAL  
DIGITAL  
The sub woofer speaker indicators will flash.  
9
Within 10 seconds, press the SET UP ( or ) button  
to select "SP-YES" or "SP-NO".  
6
7
Notes:  
2 seconds  
When all 6 speakers have been connected, set each of  
DIGITAL  
the items to "LARGE", "SMALL" or "YES".  
When using the speakers included with this unit, the rec-  
ommended speaker size settings are "SMALL" for the  
front and center speakers and "SP-YES" for the surround  
and sub woofer.  
DIGITAL  
DIGITAL  
8
9
2 seconds  
DIGITAL  
DIGITAL  
16  
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(Continued)  
Speaker delay setting  
The best sound will be achieved by placing the front speak-  
ers, center speaker and surround speakers at the same dis-  
tance from the listener.  
When some of the speakers are at a different distance from  
the listener, you can select a speaker delay to make it seem  
as though the speaker distances are the same.  
(Factory-shipped settings: CENTER 0 ms, SURROUND  
5 ms)  
MENU  
ITEM  
If the settings need to be changed due to the type of sound  
source being played or the conditions in the room, change  
them as follows.  
SET UP  
1
2
Press the MENU button repeatedly to make "SP DELAY"  
appear.  
Within 10 seconds, press the ITEM button to select  
"CENT-SP" or "SURR-SP".  
CENT-SP: To delay the sound from the center speaker  
SURR-SP: To delay the sound from the surround  
speakers  
DIGITAL  
1
2
3
The selected speaker indicator(s) will flash.  
3
Within 10 seconds, press the SET UP ( or ) button  
to select a value.  
DIGITAL  
Adjustable range  
CENTER: 0 ms - 5 ms  
SURROUND: 0 ms - 15 ms  
(When the DIGITAL indicator is lit)  
15 ms - 30 ms  
DIGITAL  
mS  
0
1
4
5
(When the DIGITAL indicator is not lit)  
(Can be changed in 1 ms steps.)  
DIGITAL  
2
3
Notes:  
As a guide for setting the correct delay time, 1 ms is  
equal to approximately 12" (30 cm) from where the se-  
lected speakers are placed further away from the listener  
than the typical location.  
DIGITAL  
mS  
0
1
14 15  
If the delay time for the surround speakers is set to a  
large value, a large sound space will be created. If it is  
set to a small value, the sound space will be small and  
intimate.  
17  
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(Continued)  
Front speaker balance adjustment  
You can adjust the balance between the left and right chan-  
nels of the front speakers.  
1
2
Press the MENU button repeatedly to make "SP LEVEL"  
appear.  
Within 10 seconds, press the ITEM button to make "F-SP  
CEN" appear.  
MENU  
ITEM  
SET UP  
The front speaker indicators will flash.  
3
Within 10 seconds, pressing the SET UP  
button will  
increase the right speaker level (the left speaker level will  
decrease), or pressing the SET UP button will increase  
the left speaker level (the right speaker level will de-  
crease).  
DIGITAL  
DIGITAL  
DIGITAL  
If the SET UP ( or ) button is held down, the speaker  
1
2
3
level can be changed continuously.  
The speaker balance, as shown in the display, can be  
changed within a range of "1" to "20".  
Note:  
The surround speaker balance will not be changed.  
To balance the front speaker(s):  
In step 3, press the SET UP ( or ) button to make "F-SP  
CEN" appear.  
1
2
2
9
9
20  
20  
DIGITAL  
Speaker level setting  
The output level of the center, surround or sub woofer speak-  
ers can be adjusted.  
1
1
2
Press the MENU button repeatedly to make "SP LEVEL"  
appear.  
Within 10 seconds, press the ITEM button repeatedly to  
select the speaker (CENT, RSUR, LSUR or SWFR) you  
want to adjust.  
DIGITAL  
DIGITAL  
1
2
The selected speaker indicator will flash.  
Note:  
dB  
dB  
dB  
dB  
While  
displayed.  
If DIGITAL is not lit, "SURR" will be displayed.  
DIGITAL is lit, "RSUR" and "LSUR" will be  
DIGITAL  
DIGITAL  
DIGITAL  
3
Within 10 seconds, press the SET UP ( or ) button  
to adjust the output level.  
You can change the level within a range of +10dB to  
-10dB, in 1dB steps.  
While  
can be adjusted independently by displaying "RSUR" and  
"LSUR". However, if DIGITAL is not lit, "SURR 0dB"  
DIGITAL is lit, the left and right speaker levels  
will be displayed, and both channels will be adjusted at  
the same time.  
18  
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(Continued)  
Test tone  
You can check (and adjust) the speaker level by listening to  
the sound output from each speaker individually, while stand-  
ing at the actual listening position in the room.  
The speaker level can be adjusted using the remote control.  
1
Press the MENU button repeatedly to make "TEST" ap-  
pear.  
MENU  
ITEM  
SET UP  
2
Within 10 seconds, press the ITEM button.  
The test tone will be heard from each speaker, in order,  
at about 5 second intervals.  
Note:  
While  
DIGITAL is lit, "R-SURR" and "L-SURR" will be  
DIGITAL is not lit, "SURR" will be displayed.  
displayed.  
If  
DIGITAL  
L-FRNT  
1
2
CENTER  
R-FRNT  
DIGITAL  
DIGITAL  
DIGITAL  
DIGITAL  
R-SURR  
L-SURR  
S-WOOFER  
When the test tone is being output, the indicator for that  
speaker will flash.  
The test tone will be heard until the current menu selec-  
tion is changed by pressing the MENU button again, or  
by selecting some other function.  
3
To adjust the speaker level while the test tone is being  
output from a particular speaker, press the SET UP (  
or ) button.  
The speaker level can be adjusted within a range of  
+10dB to -10dB, in 1dB steps.  
DIGITAL  
Notes:  
If "NO" is selected for any individual speaker’s size setting  
(page 16), the test tone will not be heard from that  
speaker.  
DIGITAL  
Please note that the front left and front right speaker lev-  
els cannot be adjusted using this method.  
When a surround test is performed while  
lit, "R-SURR" and "L-SURR" will be displayed and can  
be adjusted. However, if DIGITAL is not lit, "SURR"  
DIGITAL is  
DIGITAL  
3
will be displayed, and both channels will be adjusted at  
the same time.  
19  
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(Continued)  
Dynamic range setting  
DVD discs have a wider dynamic range (sound volume  
range) than existing VHS videotapes or CD discs. If they are  
played in home systems, there may be too much difference  
between the loud and quiet sounds. Therefore, if the volume  
is set so that the quiet sounds can be heard clearly, the loud  
sounds may be far too loud.  
On the other hand, if the volume is set so that the loud  
sounds are not too loud, you may not be able to hear the  
quiet sounds. Three settings are available to control the dy-  
namic range easily.  
MENU  
ITEM  
SET UP  
1
2
Press the MENU button repeatedly to make "D-RANGE"  
appear.  
Within 10 seconds, press the ITEM button to select  
"MAX", "STD" or "MIN".  
MAX:  
This setting does not compress the dynamic range  
of the Dolby digital signal, allowing you to enjoy  
the full, powerful sound of Dolby encoded digital  
signals.  
DIGITAL  
STD:  
MIN:  
This setting compresses the dynamic range, and  
may produce a more appropriate volume range for  
home use.  
This setting compresses the dynamic range, allow-  
ing you to enjoy movies at a lower volume.  
1
2
DIGITAL  
DIGITAL  
DIGITAL  
Returning various surround settings to their de-  
fault condition:  
1
1
Hold down the DOLBY SURROUND button on the main  
unit until "CLEAR" appears.  
2
Within 5 seconds, press the ENTER button.  
As shown on the setup menu, any of the settings that  
have been changed will be returned to their factory de-  
fault settings.  
2
20  
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RADIO OPERATION  
Tuning  
1
1
2
3
Set the POWER button on the main unit to ON.  
Press the TUNER (BAND) button.  
Press the TUNER (BAND) button again to select the de-  
sired frequency band. (FM ST, FM or AM)  
4
Press the TUNING (UP or DOWN) button to tune into  
the desired station.  
2,3,5,6  
4
Manual tuning:  
Press the TUNING (UP or DOWN) button as many times as  
required to adjust the frequency shown in the display to the  
frequency of the desired station.  
Auto tuning:  
When the TUNING (UP or DOWN) button is pressed for  
more than 0.5 seconds, scanning will start automatically and  
the tuner will stop at the first receivable broadcast station.  
Notes:  
When radio interference occurs during auto scan tuning,  
auto scan tuning may stop automatically at that point.  
If a weak station signal is found during auto scan tuning,  
the station will be skipped.  
To stop auto tuning, press the TUNING (UP or DOWN)  
button again.  
5
To receive an FM stereo transmission, press the TUNER  
(BAND) button so that the "STEREO" indicator on the  
display lights up.  
" " will appear when an FM broadcast is in stereo.  
6
If the FM reception is weak, press the TUNER (BAND)  
button so that the "STEREO" indicator goes out.  
Although the reception changes to monaural, the sound  
becomes clearer.  
After use:  
Set the POWER button on the main unit to OFF.  
Notes:  
The last station tuned in will be recalled, even after  
changing the tuning band or the function, or after turning  
the power off.  
When listening to a radio station broadcasting monaural  
sound, select STEREO in the Dolby Surround mode.  
21  
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(Continued)  
Preset tuning  
You can store up to 40 stations in memory (40 stations con-  
sisting of any combination of FM and AM stations you like)  
and recall them at the push of a button.  
To enter stations into memory:  
1
2
Perform steps 1 - 6 in the "Tuning" section.  
Press the MEMORY button.  
"MEMORY" will flash.  
3
Within 5 seconds, turn the jog dial to make the preset  
channel number flash in the display.  
Store the stations in memory, in order, starting with preset  
channel 1.  
4
Within 5 seconds, press the ENTER button to store that  
station in the selected station preset number memory.  
2
4
3
If the "MEMORY" and preset number indicators go out  
before the station is memorized, repeat the operation  
from step 2.  
5
Repeat steps 1 - 4 to set other preset stations, or to  
change a preset station.  
To recall a memorized station:  
Turn the jog dial on the main unit or press the PRESET (  
or ) button on the remote control for less than 0.5 seconds  
to select the desired station.  
The stations (preset channel number, frequency and fre-  
quency band) which have been stored in memory will  
appear in the display in numerical order, irrespective of  
the frequency bands.  
Note:  
When searching for a memorized station, do not press the  
PRESET button for more than 0,5 seconds.  
When the PRESET button is pressed for more than 0,5 sec-  
onds, the unit will enter the preset memory scan mode.  
Backup function:  
The backup function protects all station presets for a few hours  
should there be a power failure or the AC power cord is removed  
from the AC outlet.  
Preset memory scan  
The stations saved in the preset memory can be scanned auto-  
matically.  
1
To scan the preset stations, press the PRESET (  
button for more than 0,5 seconds.  
or  
)
PRESET  
The station preset number will flash and the programmed sta-  
tions will be tuned in sequentially, for 5 seconds each.  
2
Press the PRESET ( or ) button again to stop the mem-  
ory scan at the desired station.  
Note:  
When the preset memory does not have any stations stored in  
it, the preset memory scan will not function.  
To erase the contents in the preset memory:  
1
2
3
Select the preset channel number you want to erase.  
Hold down the MEMORY button until "CLR" appears.  
Within 5 seconds, press the ENTER button.  
After performing this operation, the preset memory informa-  
tion will be erased.  
22  
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO USE THE BUILT-IN TIMER  
Timer playback  
Timer operation is only possible when the TUNER func-  
TIMER  
1
tion is selected.  
1
2
Set the POWER button on the main unit to ON.  
Press the TUNER (BAND) button.  
Tune in the desired station.  
3
4
Press the TIMER/SLEEP button repeatedly until "TIMER"  
is displayed.  
Turn the jog dial to select how many hours from now you  
want to start timer playback.  
2
4
5
3
The maximum time that you can specify is 12 hours, in  
15-minute intervals.  
OFF 0:15 0:30 ....... 11:45 12:00  
3
4
5
Press the ENTER button.  
After the timer setting has been displayed for 2 seconds,  
the tuner band and station will be displayed.  
The TIMER indicator will light up. The unit will enter the  
timer stand-by mode.  
6
7
Adjust the volume level.  
Press the POWER button on the remote control to turn  
the power off.  
Note:  
When you set the POWER button on the main unit to  
OFF, the main power will be turned off, and timer play-  
back will not work.  
8
When the timer start time is reached, timer playback will  
start.  
7
The volume will increase gradually until it reaches the  
volume you were listening to before turning off the unit.  
Even if you selected a different function other than the  
tuner before turning off the power, the tuner will be se-  
lected.  
9
The power will be turned off one hour after the timer has  
started.  
When it is one minute before the timer-off time, the vol-  
ume will start to fade.  
To check the timer setting (when in the timer play-  
back stand-by mode):  
Press the TIMER/SLEEP button once.  
The remaining operation time will be displayed for 2 sec-  
onds. Then the tuner band and station will be displayed  
for 2 seconds.  
To cancel the timer operation:  
Press the POWER button to turn the power on.  
To resume timer playback:  
To set timer playback again after a timer playback operation  
has finished, perform steps 1 - 7 above.  
The timer playback setting time will be canceled after a  
timer playback operation has finished.  
23  
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(Continued)  
Sleep operation  
The tuner and any components that are connected to the  
DVD, VCR-1, VCR-2, CD/AUX, MD/TAPE or PHONO jacks  
can be turned off automatically.  
1
2
Play back the desired sound source.  
Press the TIMER/SLEEP button repeatedly until "SLEEP"  
is displayed.  
3
Turn the jog dial to set the sleep time.  
The maximum sleep time you can specify is 2 hours, in  
2
3
4
1
5-minute intervals.  
OFF 5 10 ............ 1:55 2:00  
4
5
Press the ENTER button.  
2
3
The unit will turn off automatically after the preset sleep  
time has elapsed.  
When it is one minute before the sleep-off time, the vol-  
ume will start to fade.  
To check the remaining sleep time:  
Press the TIMER/SLEEP button twice.  
To cancel the sleep operation:  
Press the POWER button to turn the power off.  
Notes:  
After the sleep operation has finished, the sleep setting  
time will be canceled. If you want to set the sleep oper-  
ation again, start from the beginning of this procedure.  
The sleep operation cannot control any components that  
are connected to the DVD, VCR-1, VCR-2, CD/AUX,  
MD/TAPE or PHONO jacks.  
HEADPHONES  
Before plugging in or unplugging the headphones, make  
sure the volume level is reduced.  
Be sure your headphones have a 1/4" (6.3 mm) diameter  
plug and are between 16 ohms and 50 ohms impedance.  
The recommended impedance is 32 ohms.  
1
2
Set the SPEAKERS A and B button to OFF.  
When headphones are connected, adjust the VOLUME  
control for the desired volume.  
Note:  
When using headphones, it is recommended that you se-  
lect STEREO in the Dolby Surround mode.  
24  
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DESCRIPTION OF TERMINOLOGY  
Dolby Pro Logic Surround:  
Dolby Digital:  
This refers to the Dolby Surround sound decoder system  
which is used for movies. Using 4 channels, the sound ef-  
fects, dialog, sound direction, music, etc. are all reproduced  
more realistically. Dolby Pro Logic Surround makes the lo-  
cation and movement of sounds much more natural than the  
original Dolby Surround system. You can enjoy a realistic,  
powerful feeling like being at a live performance or as if you  
were at a movie theater or in a concert hall. In order to enjoy  
this effect, you need at least one pair of surround speakers  
and center speaker.  
This is the new digital surround system that was created to  
reproduce theater quality stereophonic Dolby Surround  
sound at home. Films are now recorded using the 5.1 chan-  
nel system. Dolby Digital can handle the original soundtrack  
without modification, allowing you to enjoy the sound field  
created by the film maker at home.  
L
C
R
L
C
R
S
S
Dolby Pro Logic  
Dolby Digital  
2
4
Number of recording channels  
Number of playback channels  
6
6
Front (L, R) + Center + Rear (L, R) +  
Low frequency effects (sub woofer)  
Front (L, R) + Center + Rear  
Playback configuration of channels  
Discrete processing,  
Dolby digital encoding/decoding  
Matrix processing, Dolby Surround  
Sound processing  
16 bits  
7 kHz  
Number of signal processing bits  
20 bits  
Surround Sound high-frequency  
playback limit  
20 kHz  
Dolby Surround:  
PCM (Pulse Code Modulation)  
This is a recording/transmission system used for digital audio  
signals. This unit can handle sampling frequencies of 32 kHz,  
44.1 kHz and 48 kHz.  
This is the encoding/decoding system for general-purpose  
Dolby Surround. When the sound from films recorded in  
Dolby Surround are reproduced, you will have the feeling of  
being at a live performance, as if the action is taking place  
right in front of you.  
Sub woofer:  
The sub woofer is a special speaker used to emphasize bass  
sounds.  
LFE (Low Frequency Effect):  
This refers to the special low-frequency sound effects used  
in Dolby Digital recordings.  
When a signal containing LFE encoding is played by this  
unit, "LFE" will appear in the display.  
In Dolby Digital, this speaker reproduces the LFE signals as  
well as the low-frequency signals being sent to the front,  
center and surround speakers.  
In Dolby Pro Logic, this speaker reproduces the low-fre-  
quency signals sent to the front and center speakers.  
It also reproduces low frequency sounds from ordinary stereo  
recordings.  
25  
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
External care  
Periodically wipe the cabinet with a soft cloth and a di-  
luted soap solution, then wipe with a dry cloth.  
Do not use chemically treated cleaning cloths or other  
chemicals.  
SPECIFICATIONS  
As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes  
for product improvement without prior notice. The performance specification figures indicated are nominal values of pro-  
duction units. There may be some deviations from these values in individual units.  
Center speaker section  
General  
Type:  
2-way, 5-1/8" (13 cm) woofer,  
and 2" (5 cm) tweeter  
Type:  
Power source:  
Power consumption: 170 W  
Dimensions:  
Home theater receiver  
AC 120 V, 60 Hz  
Maximum input power: 80 W  
Impedance:  
Dimensions:  
8 ohms  
Width; 16-15/16" (430 mm)  
Width; 15-3/4" (400 mm)  
Height; 6-1/2" (165 mm)  
Depth; 6-7/16" (163 mm)  
6.4 lbs. (2.9 kg)  
Height; 5-15/16" (150 mm)  
Depth; 13-11/16" (347 mm)  
21.6 lbs. (9.8 kg)  
Weight:  
Output power:  
Weight:  
(Front)  
40 watts minimum RMS per chan-  
nel into 8 ohms from 60 Hz to  
20 kHz, 0.9% total harmonic dis-  
tortion.  
(Center)  
RMS; 40 W (0.9% T.H.D.)  
(Surround)  
RMS; 40 W/CH (0.9% T.H.D.)  
(Sub woofer)  
RMS; 40 W (0.9% T.H.D.)  
Front speakers; 8 ohms  
Center speaker; 8 ohms  
Surround speakers; 8 ohms  
Sub woofer; 8 ohms  
Surround speaker section  
Type:  
2-way 5-1/8" (13 cm) woofer,  
and 2" (5 cm) tweeter  
Maximum input power: 80 W  
Impedance:  
8 ohms  
Dimensions:  
Width; 8-5/16" (210 mm)  
Height; 6-1/2" (165 mm)  
Depth; 6-7/16" (163 mm)  
3.5 lbs. (1.6 kg)/each  
Output terminals:  
Input terminals:  
Weight:  
Headphones; 16-50 ohms  
(recommended; 32 ohms)  
DVD, VCR-1, VCR-2, CD/AUX,  
MD/TAPE; 500 mV/47 kohms  
PHONO; 3.5 mV/47 kohms  
Sub woofer section  
Type:  
6-5/16" (16 cm) super woofer  
Maximum input power: 80 W  
Tuner section  
Impedance:  
8 ohms  
Frequency range:  
FM; 87.5-108 MHz  
AM; 530-1,720 kHz  
Dimensions:  
Width; 8-5/16" (210 mm)  
Height; 13" (330 mm)  
Depth; 13-3/8" (340 mm)  
11.5 lbs. (5.2 kg)  
Front speaker section  
Weight:  
Type:  
2-way, 6-5/16" (16 cm) woofer,  
and 2" (5 cm) tweeter  
Maximum input power: 80 W  
Impedance:  
Dimensions:  
8 ohms  
Width; 8-5/16" (210 mm)  
Height; 13" (330 mm)  
Depth; 8-5/8" (218 mm)  
8.2 lbs. (3.7 kg)/each  
Weight:  
26  
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONSUMER LIMITED WARRANTY  
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the “Product”), when  
shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair  
the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for  
parts or labor for the period(s) set forth below.  
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any  
Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal  
service or handling, or which has been altered or modified in design or construction.  
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of  
purchase to the servicer.  
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED  
WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITYAND FITNESS FOR USEARE LIMITED TO THE PERIOD(S)  
FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow limitations on how long an implied warranty lasts,  
so the above limitation may not apply to you.  
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein,  
or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.  
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive  
remedy available to the purchaser. Correction of defects, in the manner and for the period of time described herein, shall constitute  
complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full  
satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in any  
way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone  
other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or  
property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not  
apply to you.  
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE  
TO STATE.  
Model Specific Section  
HT-DD5000 Home Theater System  
Your Product Model Number & Description:  
(Be sure to have this information available when you need service for your Product.)  
One (1) year parts and labor from the date of purchase.  
Warranty Period for this Product:  
Additional Item(s) Excluded from  
Warranty Coverage (if any):  
Where to Obtain Service:  
Non-functional accessories, supplies and consumable items.  
At a Sharp Authorized Servicer located in the United States. To find a location of the  
nearest Sharp Authorized Servicer, call Sharp toll free at 1-800-BE-SHARP.  
Ship prepaid or carry in your Product to a Sharp Authorized Servicer. Be sure to  
have Proof of Purchase available. If you ship the Product, be sure it is insured and  
packaged securely.  
What to do to Obtain Service:  
TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP.  
SHARP ELECTRONICS CORPORATION  
Sharp Plaza, Mahwah, New Jersey 07430-2135  
SHARP CORPORATION  
TINSE0009SJZZ  
Printed in China  
A9806.SM  
HT-DD5000(SEC) TINSE0009SJZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Silicon Laboratories Computer Hardware SI5351A B C User Manual
Singer Iron ESP 2 User Manual
Snapper Lawn Mower ZF2100DKU ZF2300GKU ZF5200M ZF6100M User Manual
Sony Camera Accessories 370PK1 User Manual
Sony DVD Player RDR GX300 User Manual
Sony Microcassette Recorder ICD B120 User Manual
Sony Network Card PCWA C300S User Manual
Star Manufacturing Toaster BT4 User Manual
Sunbeam Fryer 3254 33 User Manual
Sylvania TV VCR Combo 6313CB 6319CB User Manual