Controls and indicators (continued)
System preparation
Accessories
The following accessories are included.
ENGLISH
1
To mount the sound bar on the wall
■ Rear Panel
2
Make a hole on the wall following the screw
point marks on the pattern paper by using
a drill.
MODEL
1. DC In Jack
Caution:
2. Audio In Jack
●
●
Be very careful to prevent the sound bar [5.07 lbs.
(2.3 kg)] from falling when mounting on the wall.
Before mounting, check the wall strength. (Do not
put on the veneer plaster or whitewashed wall. The
sound bar may fall.) If unsure, consult a qualified
service technician.
1-1/4” (32 mm)
HT-SB20
HT-SB30
Remote control x 1
(RRMCGA326AWSA: HT-SB20)
(RRMCGA322AWSA: HT-SB30)
AC/DC adaptor x 1
(RADPAA096AWZZ)
AC power cord x 1
(QACCDA005AWZZ)
3/8” (8-9 mm)
Wall surface
●
Mounting screws are not supplied. Use appropri-
ate ones.
SOUND BAR HOME THEATER SYSTEM
3
4
Fix a wall mount plug into the hole using
a hammer, until it is flush with the wall
surface.
2
●
●
Check all wall mount angle screws for looseness.
Select a good location. If not, accidents may occur
or the sound bar may get damaged.
SHARP is not responsible for accidents result-
ing from improper installation.
1
2
■ Remote Control
OPERATION MANUAL
ON/
MUTE
STAND-BY
1-1/4” (32 mm)
●
Audio cable x 1
(QCNWGA087AWPZ)
Pattern paper x 1
(TCAUHA034AWZZ)
12
13
1. Remote Control Transmitter
2. Mute Button
3. Cinema (Sound Mode) button
4. Music (Sound Mode) button
5. Surround Button
6. Bypass (Sound Mode) button
7. TV Operation Buttons
8. Bluetooth Pairing Button (HT-SB30 only)
9. Bluetooth Play/Pause Button (HT-SB30
only)
SOUND MODE
MUSIC
CINEMA
NEWS
INPUT
3
4
5
6
3/8” (8-9 mm)
Wall surface
■ Driving screws
SHARP designed the sound bar so you may hang
it on the wall. Use proper screws (not supplied).
The illustrations printed in this manual are for the model HT-SB30.
BYPASS SURROUND
14
ON/
Y
D-B
AN
ST
TE
MU
DE
MO
ND
OU
NE
WS
S
SIC
MU
TV
A
EM
CIN
Controls and indicators
UT
INP
UND
RRO
SU
SS
PA
BY
TV
Fastenthescrewstothewallasshownbelow.
(Total screw is 2 pieces)
CH
See below for size and type.
L
VO
VOL
CH
7
■ Front Panel (HT-SB20)
L
VO
1 2 3 4
5 6
7 8
1/8” (3.2 mm)
1. On/Stand-by
Indicator
2. On/Stand-by
Button
3. Surround Button
4. Surround Indicator
5. Volume Indicator
6. Volume Down
Button
7. Volume Up Button
A
WS
2A
32
GA
MC
RR
Screw using
Screwdriver
8
9
3/16”
(5 mm)
8. Remote Sensor
9. Left Channel
Speakers
10. Bluetooth Skip Up Button (HT-SB30 only)
11. Bluetooth Skip Down Button (HT-SB30
only)
3/8” (9 mm)
VOL
15
10
11
Wall surface
Min. 7/8” (22 mm)
10. Right Channel
Speakers
SOUND BAR HOME THEATER SYSTEM HT-SB20
12. On/Stand-by Button
13. News (Sound Mode) button
14. Input Button (HT-SB30 only)
15. Volume Up/Down Buttons
4.5mm - 5mm
RRMCGA322AWSA
■ Installing the sound bar
Gap from
wall surface
Wall surface
SOUND BAR HOME THEATER SYSTEM HT-SB20
Note:
Remote control
1
Fix the pattern paper to the wall in hori-
zontal position as below.
Plastic shield
Before using remote control, please remove plastic
shield at battery holder.
9
10
6 7 8 9 10
5
Hang the sound bar onto the screws.
509 mm
Wall
surface
(HT-SB30 only)
548 mm
■ Front Panel (HT-SB30)
44 mm
1 2 3 4 5
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by SHARP is under license. Other
trademarks and trade names are those of their respective owners.
Battery holder
TV Operation Buttons (Only SHARP TV):
1. On/Stand-by
Indicator
2. On/Stand-by
Button
10. Remote Sensor
11. Left Channel
Speakers
Note: This product is recommended for flat panel TV (LED, LCD and plasma).
Pattern paper
(supplied)
12. Right Channel
Speakers
On/Stand-
by Button
Volume Up
and Down
Buttons
Sets the TV power to
“ON” or “STAND-BY”.
Turn up/down the TV
volume.
Input Select
Button (TV)
Channel Up and
Down Buttons
Press the button to
switch the input source.
Switch up/down the TV
channels.
SOUND BAR HOME THEATER SYSTEM HT-SB30
3. Input Button
4. Pairing Button
5. Pairing Indicator
6. Surround Indicator
7. Surround Button
8. Volume Down
Button
Caution: Before operating this product, refer “IMPORTANT SAFEGUARDS AND
WARRANTY” at the reverse page of English operation manual.
VOL
CH
SOUND BAR HOHEATEEM HT-SB30
9. Volume Up Button
Note:
●
●
Some models of SHARP TV may not be operable.
SHARP TV remote control will not work with HT-SB20/HT-SB30 system.
11
12
Printed in Malaysia
13A R AS 1
E-1
E-2
E-3
TINSZB425AWZZ
■ When mounting on the wall
Sound bar connections to TVs
Placing the sound bar
Installation image:
AC power connection
Screw eye (not supplied)
Notes:
After checking all the connections have
been made correctly, connect the AC
power cord to the AC power input jack,
then to the AC outlet.
Caution:
Make sure to unplug the AC power
cord before making any connections.
●
Remove the protective film covering the sound
Turn off all other equipment before making any connections.
Safety wires (not
supplied)
bar before turning on the system.
The front panel of the sound bar is not
removable.
TV
●
Notes:
● To connect to TV, use Audio IN terminals located at the rear of the sound bar.
● Refer the operation manual of the equipment to be connected.
● Fully insert the plugs to avoid fuzzy pictures or noises.
Place the
sound
bar as
shown.
AC/DC Adaptor
Caution:
2
■
Using with the AC/DC adaptor
SOUND BAR HOME THEATER SYSTEM HT-SB30
Cable
●
Do not change the installation direction when
● In some cases, a small background noise could emit from the sound bar, when you
use the RCA audio output terminal connection from a TV-Set/DVD/Blu-ray Disc
Player. In such case, please change the connection to the headphone terminal
connection. This effect depends on the used TV/DVD/Blu-ray Disc Player-Brand,
model and age, and it is not a quality matter from the sound bar.
● If the TV volume is continuously at low level, the sound bar will automatically
power off. Increase the TV output volume to enjoy the sound from the speaker.
the sound bar is turned on.
Do not stand or sit on the sound bar as you
may be injured.
1 Plug the AC power cord into the AC/
DC adaptor.
2 Plug the AC/DC adaptor cable into
the DC INPUT jack on the sound
bar.
●
DC IN jack
(DC 17V)
Sound bar
Wall
AC power cord
DVD player
3 Plug the AC power cord into an AC
VCR
1
AC outlet
outlet.
■
Connecting a TV, or DVD player, etc.
■ When placing on the shelf/table
AC/DC Adaptor
(AC 100 - 240 V ~ 50/60 Hz)
Notes:
Falling prevention
Safety wires (not supplied) are useful to prevent the sound bar from falling.
If the TV/monitor has an audio output, connect it to the Audio IN jack on the rear
of the sound bar.
● During power standby, the stand-by
indicator turns RED. If ON-STANDBY
button is pressed, the STAND-BY
indicator turns BLUE.
● Unplug the AC/DC adaptor from the
AC outlet if the sound bar will not be
used for a prolonged period of time.
● Use only the supplied AC/DC adaptor.
Using other AC/DC adaptor may
cause an electric shock or fire.
●
Sound bar
HT-SB30
To select AUDIO IN function:
Press INPUT button repeatedly.
To select Bluetooth function:
Press INPUT button repeatedly. (PAIRING indicator turns blue.)
TV
Screw eye
(not supplied)
To audio output terminals
Safety
Rack/
table
wires
(not
supplied)
Screw eye
(not supplied)
or
To HEADPHONE
terminal
Blu-Ray/DVD player/
Digital Tuner
Audio cable
Audio cable
(not supplied)
To AUDIO
IN jack
Sound bar
E-4
E-5
E-6
E-7
Listening to Bluetooth enabled devices (for HT-SB30) (continued)
General control
Remote control
Listening to Bluetooth enabled devices (for HT-SB30)
ON/STAND-BY
PAIRING
Audio stream
Precautions for battery use:
5
Select “SHARP HT-SB30” from the source
list. If Passcode* is required, enter “0000”.
Pairing indicator (blue) on the sound bar will
stop blinking once the sound bar is success-
fully paired with the source device. Pairing
information is now memorized in the sound
bar.
■ To turn the power on
Press the ON/STAND-BY button.
The STAND-BY indicator turns BLUE.
■ Sound Mode
■
About Bluetooth technology
■ Battery installation
O
N
/
S
T
A
N
D
-
B
Y
S
O
U
R
C
E
PAIRING
SURROUND
-
VOLUME
+
SOUND BAR HOME THEATER SYSTEM HT-SB30
Remove the battery if the sound bar will
not be used for a long period of time.
This will prevent potential damage due
to battery leakage.
O
N
/
S
T
A
N
D
-
B
Y
S
O
U
R
C
E
PAIRING
SURROUND
-
VOLUME
+
Bluetooth wireless technology is a short-range radio
technology that enables wireless communication
between various types of digital devices, such
as mobile phone or computer. It operates within
a range of about 10 meters (30 feet) without the
hassle of having to use cables to connect these
devices. Since the Bluetooth technology does not
require line of sight between the communicating
devices, it is not necessary to line up the transmit-
ting device and the receiver, as in the case of infra
red technology.
This product contains a CR Coin
Lithium Battery which contains Per-
chlorate Material – special handling
may apply, California residents, see
chlorate/
Remote control operation:
Press the desired sound mode button
on the remote control.
SOUND BAR HOME THEATER SYSTEM HT-SB30
Bluetooth mobile phone or other
Bluetooth Stereo audio source device
Note:
If the power does not turn on, check whether
the power cord is plugged in properly.
■
Pairing with other Bluetooth
Caution:
HT-SB20
● Do not use rechargeable battery
(nickel-cadmium battery, etc.).
● Danger of explosion if battery is in-
correctly replaced.
source device
■
Pairing Bluetooth devices
The VOLUME indicator: blinking
HT-SB30
To set the sound bar to stand-by mode:
Press the ON/STAND-BY button again. The
STAND-BY indicator turns RED.
* Passcode may be called PIN Code, Passkey,
PIN number or Password.
1
2
3
Press the ON/STAND-BY button to turn the
power on.
Bluetooth devices need to be initially paired first
before they can exchange data. Once paired, it is
not necessary to pair them again unless:
1
While pushing the locking tab to-
wards the center of the remote con-
trol, slide out the battery holder.
● Replace only with the same or
equivalent type.
The SURROUND indicator: blinking
6
Start the Bluetooth connection from the
source device.
Some audio source devices may connect with
the sound bar automatically, otherwise follow
the instructions in the source device operating
manual to start connection.
Press the INPUT button to select Bluetooth
function. (PAIRING indicator blinks.)
■ Volume auto fade-in
If you turn off and on the sound bar again,
volume will start at lower level and gradually
increase to the last set level.
CINEMA (for cinema sound effect)
MUSIC (for standard sound effect)
● Batteries (battery pack or batteries
installed) shall not be exposed to ex-
cessive heat such as sunshine, fire
or the like.
●
pairing is made with more than 8 devices.
Pairing can only be made one device at
a time. This sound bar can be paired to a
maximum of 8 devices. If subsequent device
is paired, the oldest device paired, will be de-
leted and replaced with the new one.
Back of
remote control
Press and hold the PAIRING button for 1
second or more.
NEWS
(for news)
Communication System and Bluetooth Profile
of this sound bar
There are many available Bluetooth Profiles
describing the basic communication methods,
specific functions and uses, to enable communica-
tion between devices.
● Installing the battery incorrectly may
cause the sound bar to malfunction.
PAIRING indicator blinks quickly. The sound
bar is now in pairing mode and is ready to be
paired with other Bluetooth source device.
BYPASS (for flat sound effect)
■ Volume control
Sound bar operation:
Press volume up (VOLUME + ) to increase
the volume and press volume down (VOL-
UME – ) to decrease the volume.
Locking
tab
Notes concerning use:
■ Function
Notes:
● Replace the battery if the operating
distance is reduced or if the opera-
tion becomes erratic. Purchase “CR
2025”, coin lithium battery.
●
●
this sound bar is reset. All pairing information
is deleted when sound bar is reset.
pairing information is deleted while repairing, etc.
●
If this sound bar or the source device is turned
Note:
2
Remove the old battery from the
battery holder, insert the new bat-
tery and then slide the battery hold-
er back into the remote control.
HT-SB20
off before Bluetooth connection is completed,
pairing will not be completed and the pairing
information will not be memorized. Repeat
step 1 onwards to start pairing again.
To pair with other devices, repeat steps 1 - 5
for each device.
This sound bar can be paired to a maximum
of 8 devices. If subsequent device is paired,
the oldest device paired, will be deleted and
replaced with the new one.
Pairing indicator (blue) will stop blinking once
the sound bar is successfully paired with the
source device.
When the sound bar is connected to the TV/
DVD, etc., the AUDIO IN function is ready
to be used.
This sound bar supports the following:
Communication System: Bluetooth Specification
version 2.1 Bluetooth + Enhanced Data Rate
(EDR) Profile : A2DP (Advanced Audio Distribu-
tion Profile)
A2DP enables audio streaming from an A2DP
equipped Bluetooth stereo audio source device
(eg mobile phone) to this sound bar. By convert-
ing wireless stereo audio signal to analogue audio
signal, you can enjoy listening to the sound through
this speaker system.
● Periodically clean the transmitter on
the remote control and the sensor
on the sound bar with a soft cloth.
● Exposing the sensor on the sound
bar to strong light may interfere with
operation. Change the lighting or the
direction of the sound bar if this oc-
curs.
On indicators
Remote control operation:
Press the VOL + button to increase the
volume and the VOL – button to decrease
the volume.
Status
PAIRING indicator (blue)
Blinks
4
Perform pairing procedure on the source
device to detect this sound bar. (Refer
the source device operating manual for
details).
“SHARP HT-SB30” will appear in the detected
devices list (if available) in the source device.
Positive (+)
side up
Battery holder
●
HT-SB30
Unconnected
Pairing mode
Connected
Polarity
(+) symbol
When the INPUT button is pressed, the input
source will change.
Blinks quickly
Lights up
Note:
When volume is maximum or minimum:
Battery type
Locking tab
1
2
Audio In Function - the pairing indicator turns
off.
HT-SB20
● Keep the remote control away from
moisture, heat, shock, and vibra-
tions.
Bluetooth Function - the pairing indicator
turns blue.
Notes:
The VOLUME indicator: blinking
HT-SB30
●
●
Once
a
device is ousted or deleted from
●
Place the devices to be paired within 1 me-
ter (3 feet) of each other when pairing.
Note:
the pairing list, the pairing information for
the device is also deleted. To listen to the
sound from the device again, it needs to be
re-paired. Perform steps 1 - 5 to pair the de-
vice again.
Passcode of this sound bar is fixed to “0000”
and can only be paired with Bluetooth source
device whose passcode is also “0000”.
The backup function will protect the memorized
function mode for a few hours should there be
a power failure or the AC power cord becomes
disconnected.
The SURROUND indicator: blinking
AVRCP (Audio/Video Remote Control Profile) is a
technology that allows a single remote control to
control all Bluetooth enabled Audio Video equip-
ment to which a user has access.
●
Some source devices are unable to display
lists of detected devices. To pair this sound
bar with the source device, refer to the
source device operating manual for details.
■ Muting
The volume is muted temporarily when pressing
the MUTE button on the remote control. Press
again to restore the volume.
Auto power on function:
●
When stand-by indicator is VIOLET, the sound
bar will automatically power ON if it detects
audio signal from connected equipment,
unless it is turned off manually (STAND-BY
indicator turns red).
Notes when using unit with a mobile phone
●
This unit cannot be used to talk over the tele-
phone even when there is a Bluetooth con-
nection made to a mobile phone.
Please refer to the operating manual supplied
with the mobile phone for details on operation
of your mobile phone while transmitting the
sound using a Bluetooth connection.
■ Surround
When the SURROUND button is pressed, the
SURROUND sound is ON. (SURROUND indicator
turns ORANGE)
Auto power off and auto detect signal:
●
●
The sound bar will automatically go to stand-
by mode (STAND-BY indicator turns violet) if
no audio signal is detected within 20 minutes.
E-8
E-9
E-10
E-11
Listening to Bluetooth enabled devices (for HT-SB30) (continued)
Troubleshooting chart
Troubleshooting chart
Maintenance
Specifications
Many potential problems can be resolved by the
owner without calling a service technician.
If something is wrong with this product, check the
following before calling your authorized SHARP
dealer or service center.
■ Cleaning the cabinet
As part of our policy of continuous improvement,
SHARP reserves the right to make design and
specification changes for product improve-
ment without prior notice. The performance
specification figures indicated are nominal
values of production unit. There may be some
deviations from these values in individual unit.
■ Listening to the sound
■ To finish listening
■ Condensation
Bluetooth sound
●
●
Is the sound bar
too near to a device
that generates
Error indicators and
warnings
When you fail to perform operations properly, the fol-
lowing messages are displayed on the sound bar.
is interrupted or
distorted.
Periodically wipe the cabinet with a soft cloth.
Check that:
Sudden temperature changes, storage or operation
in an extremely humid environment may cause con-
densation inside the cabinet or on the transmitter
on the remote control.
Condensation can cause the sound bar to malfunc-
tion. If this happens, leave the power on until normal
operation is possible (about 1 hour). Wipe off any
condensation on the transmitter with a soft cloth
before operating the sound bar.
Perform any of the followings.
- Terminate the Bluetooth connection on the audio
source device.
Refer the operating manual supplied with the
device.
- Turn off the Bluetooth stereo audio source
device.
- Turn off this sound bar.
Caution:
●
The source device Bluetooth functionality is ON.
Pairing of this sound bar and the source device
is completed.
(HT-SB30)
electromagnetic
radiation?
●
Do not use chemicals for cleaning (petrol, paint
thinner, etc.). It may damage the cabinet finish.
●
Is there any obstacle
between the sound
bar and the Bluetooth
stereo audio source
device?
Do not apply oil to the inside of each component.
It may cause malfunctions.
Display
Meaning
■ General
●
Any device connected to the AUDIO IN socket
is turned off.
■ General
●
When the protection circuit
is activated.
Symptom
Possible cause
Power indica-
tor (blinks red)
1
Press the ON/STAND-BY button to turn the
power on.
Power source DC IN 17V
2.8A: AC/DC
No sound is heard.
●
●
Is the input signal
(selection) set
adaptor
■ Factory reset, clearing all
2
3
4
Press the INPUT button to select Bluetooth
(*): Should the same message appear even if
the sound bar is unplugged and plugged in
or is set to the stand-by mode and on again,
contact your local dealer where you purchased
the sound bar.
Note:
(AC 100 - 240V ~ 50/60Hz)
O
N
/
S
T
A
N
D
-
B
Y
S
O
U
R
C
E
PAIRING
SURROUND
-
VOLUME
+
■ Remote control
properly?
setting
SOUND BAR HOME THEATER SYSTEM HT-SB30
function.
The volume of this sound bar may not be controlled
as intended depending on the device.
Is the volume level set
to minimum?
Is muting activated?
Are the connections
made correctly?
Is the sound bar too
far from the Bluetooth
stereo audio source
device? (HT-SB30)
Is the sound bar paired
with the Bluetooth
stereo audio source
device? (HT-SB30)
Power
consumption
10W
Start the Bluetooth connection from the
Bluetooth stereo audio source device.
Symptom
Possible cause
Make sure to disconnect all audio input cables
attached to the sound bar before performing the
factory reset.
●
●
The remote control
does not operate
properly.
●
Is the battery polarity
correct?
Is the battery dead?
Is the distance or angle
incorrect?
Are there any
obstructions in front of
the sound bar?
Is there a strong light
shining on the remote
sensor?
Is the remote control
for another equipment
used simultaneously?
Start playing on the Bluetooth stereo audio
source device.
Maximum
RMS: Total 40 Watts
Bluetooth operation buttons
(remote control only)
output power 20 Watts per channel into
6 ohms at 1 kHz, 10% total
harmonic distortion
1. Unplug the AC power cord.
●
●
●
Notes:
2.
HT-SB20
If the source device has an extra bass function
or equalizer function, set them to off. If these
functions are on, sound may be distorted.
Press the button to play or pause.
FTC: Minimum 14 watts
per channel into 3 ohms at
100 Hz to
20 kHz, 1% total harmonic
distortion
Press and hold ON/STAND-BY button
and the SURROUND button and plug the
AC power cord.
●
●
●
Press the button to skip up.
●
Notes:
Press the button to skip down.
●
You need to make the Bluetooth connection
HT-SB30
again if:
Press and hold ON/STAND-BY button
and the PAIRING button and plug the AC
power cord.
Speaker
2-way Speaker System
2-1/4” (5.7cm) Woofer
1” (2.5cm) Soft Dome
- the sound bar is not turned on.
Noise is heard
during playback.
●
Move the sound
bar away from any
computers or mobile
phones.
- the source device is not turned on, or its Blue-
tooth functionality is off or is in sleep mode.
If both the Bluetooth connected device and the
one connected to the AUDIO IN are played
simultaneously, only the Bluetooth sound can
3. Press the ON/STAND-BY button
●
Input
terminals
Analog input (AUDIO IN):
Stereo mini jack Ø 3.5mm
500mV / 47kohms
Caution:
The sound bar
cannot be turned
on with the remote
control.
●
Is the AC power cord
of the sound bar
When a button
is pressed, the
sound bar does not
respond.
●
●
Set this sound bar to
the stand-by mode and
then turn it back on.
If the sound bar still
malfunctions, reset it.
(Refer to page 7.)
This operation will erase all data stored in
memory.
be heard.
plugged in?
Frequency
Band
(HT-SB30)
2.4 GHz band (2,400GHz
- 2,480GHz)
●
●
Is the battery inserted?
■ If problem occurs during
TV cannot be
operated with the
remote control.
Depending on the
model, some or all
operation
Compatible
Bluetooth
Profile
A2DP (Advanced Audio
Distribution Profile), AVRCP
(Audio/Video Remote Control
Profile)
When this product is subject to strong external
interference (mechanical shock, excessive static
electricity, abnormal supply voltage due to light-
ning, etc.) or if it is operated incorrectly, it may
malfunction.
functions may not be
operable using the
remote control of this
sound bar. In this case,
use the remote control
supplied with the TV.
The power is not
turned on.
●
●
Is the sound bar
unplugged? (Refer to
page 10)
(HT-SB30)
Bluetooth 2.1 +EDR
The protection circuit
may be activated.
Unplug and plug in the
power cord again after
5 minutes or more.
If such a problem occurs, do the following:
Dimensions
Weight
Width: 37” (940mm)
Height: 2-7/8” (73mm)
Depth: 3-1/4” (83mm)
1
Set the sound bar to the stand-by mode and
turn the power on again.
2
If the sound bar is not restored in the previous
operation, unplug and plug in the sound bar,
and then turn the power on.
5.07lbs. (2.3kg)
E-12
E-13
E-14
E-15
HT-SB30_EN_SPECIAL_NOTES_A2.indd1 1
Download from Www.Somanuals.com. All Manuals Search And Download.
2013-01-07 06:55:01
|