MULTIMEDIA PROJECTOR
MODEL
XR-55X
XR-50S
OPERATION MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating
a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse
marked or
and of the same rating as above, which is also indicated on the pin face
of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse
cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug
supplied, cut off the mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immedi-
ately and disposed of in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket
outlet, as a serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow : Earth
Blue
Brown
: Neutral
: Live
As the colours of the wires in the mains lead of this apparatus may not correspond with
the coloured markings identifying the terminals in your plug proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the
•
plug which is marked by the letter E or by the safety earth symbol
or green-and-yellow.
or coloured green
The wire which is coloured blue must be connected to the terminal which is marked
with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked
with the letter L or coloured red.
•
•
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
Authorized representative responsible for the European Union Community Market
SHARP ELECTRONICS (Europe) GmbH
Sonninstraße 3, D-20097 Hamburg
E.U. ONLY
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
The supplied CD-ROM contains operation instructions in English, German, French, Spanish,
Italian, Dutch, Swedish, Portuguese, Chinese, Korean and Arabic. Carefully read through the
operation instructions before operating the projector.
Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch,
Spanisch, Italienisch, Niederländisch, Schwedisch, Portugiesisch, Chinesisch, Koreanisch
und Arabisch. Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors
sorgfältig durch.
Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand, français,
espagnol, italien, néerlandais, suédois, portugais, chinois, coréen et arabe. Veuillez lire at-
tentivement ces instructions avant de faire fonctionner le projecteur.
El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán, francés,
español, italiano, holandés, sueco, portugués, chino, coreano y árabe. Lea cuidadosamente
las instrucciones de operación antes de utilizar el proyector.
Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese, spagnolo,
italiano, olandese, svedese, portoghese, cinese, coreano e arabo. Leggere attentamente le
istruzioni per l’uso prima di usare il proiettore.
De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Spaans,
Italiaans, Nederlands, Zweeds, Portugees, Chinees, Koreaans en Arabisch. Lees de
handleiding zorgvuldig door voor u de projector in gebruik neemt.
Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska, franska,
spanska, italienska, holländska, svenska, portugisiska, kinesiska, koreanska och arabiska.
Läs noga igenom bruksanvisningen innan projektorn tas i bruk.
O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês,
Espanhol, Italiano, Holandês, Sueco, Português, Chinês, Coreano e Árabe. Leia
cuidadosamente todas as instruções de operação antes de operar o projetor.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using the projector, please read this operation manual carefully.
ENGLISH
Introduction
There are two important reasons for prompt warranty registration of your new
SHARP Projector, using the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts,
service and labor warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection,
modification, or recall that SHARP may be required to give under the 1972
Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT
“LIMITED WARRANTY” CLAUSE.
U.S.A. ONLY
High brightness light source. Do not stare into the beam of light, or view
directly. Be especially careful that children do not stare directly into the
beam of light.
WARNING:
To reduce the risk of fire or electric shock, do not
expose this product to rain or moisture.
WARNING:
See bottom of projector.
The lightning flash with arrowhead sym-
bol, within an equilateral triangle, is in-
tended to alert the user to the presence
of uninsulated “dangerous voltage”
within the product's enclosure that may
be of sufficient magnitude to constitute
a risk or electric shock to persons.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within a triangle
is intended to alert the user to the pres-
ence of important operating and main-
tenance (servicing) instructions in the
literature accompanying the product.
FCC Regulations state that any unauthorized changes or modifications
to this equipment not expressly approved by the manufacturer could
WARNING:
void the user's authority to operate this equipment.
U.S.A. ONLY
PRODUCT DISPOSAL
This product utilizes tin-lead solder, and lamp containing a small
amount of mercury. Disposal of these materials may be regulated due
to environmental considerations. For disposal or recycling information,
please contact your local authorities, the Electronics Industries Alliance:
Sharp at 1-800-BE-SHARP.
U.S.A. ONLY
1
Download from Www.Somanuals.com. All Manuals Search And Download.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the operation manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
U.S.A. ONLY
Declaration of conformity
SHARP PROJECTOR, MODEL XR-55X/XR-50S
This device complies with Part 15 of the FCC rules. Operation is subject to the following
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Responsible Party:
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495-1163
TEL: 1-800-BE-SHARP (1-800-237-4277)
U.S.A. ONLY
Caution Concerning Lamp Replacement
■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time.
The period of time up to failure largely varies depending on the individual lamp and/or the condition
and the frequency of use. It is important to note that failure can often result in the bulb cracking.
■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.
■ Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector
Dealer or Service Center to assure safe operation.
■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In
case of exposure to the gas, consult a doctor as soon as possible.
Caution
• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may
cause burns or injury.
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to
fully cool before removing the lamp unit.
• Do not touch the glass surface of the lamp unit or the inside of the projector.
• Do not loosen other screws except for the lamp unit cover and lamp unit.
• Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and
continue to use the same lamp, this may cause the lamp to become damaged or explode.
■ Carefully change the lamp by following the instructions described on pages 56 to 58.
* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector
Dealer or Service Center.
*
If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized
Projector Dealer or Service Center for repair.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Read this Operation Manual
■ The specifications are slightly different, depending on the model. However, you can connect
and operate all models in the same manner.
•
In this operation manual, the illustration and the screen display are simplified for explanation, and
may differ slightly from the actual display. The examples used throughout this manual are based
on the XR-55X model.
Using the Menu Screen
Select from the Quick Start Menu, which is a collection of the most frequently used
functions, or the Complete Menu, which enables advanced settings and adjustments.
Adjustment buttons (P/R/O/Q)
ENTER button
MENU button
ENTER button
Buttons used in
Adjustment buttons
(P/R/O/Q)
this operation
RETURN button
• Press RETURN to return
to the previous screen
when the menu is
displayed.
MENU button
Button used in
this step
Menu Selections (Quick Start Menu)
• This operation can also be performed by using the buttons on the projector.
Example
Press MENU.
1
• The “Quick Start Menu” screen for the
selected Input mode is displayed.
Quick Start Menu
Input Search Start
Resolution
1024×768
Resize
Normal
Press P or R to select the
2
3
On-screen
display
Keystone
Eco+Quiet
Language
Information
0
desired item, then press ENTER.
Off
English
Press P/R/O/Q to adjust the
item selected, then press
ENTER.
Go To Complete Menu…
Info
SEL./ADJ.
ENTER
END
• To display the advanced settings and
adjustments, select “Go To Complete Menu”.
Press ENTER to display the Complete Menu
screen.
•
If you do not want to display the Quick Start
Menu, set “Go To Complete Menu” - “PRJ-ADJ2”
- “Quick Start Menu” to “Off”. (See page 51.)
38
.........Indicates safeguards for using the projector.
Info
Indicates additional information for setting up and operating the
projector.
.......
Note
For Future Reference
Maintenance
Troubleshooting
Index
P. 53
PP. 67 and 68
P. 72
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Preparing
Displaying the Black Screen and
Turning Off the Sound Temporarily ....... 29
Resize Mode .......................................... 30
Introduction
How to Read this Operation Manual......3
Contents.................................................4
IMPORTANT SAFEGUARDS ..................6
How to Access the PDF Operation
Manuals..............................................10
Accessories..........................................11
Part Names and Functions...................12
Front View.............................................. 12
Top View ................................................ 12
Rear View (Terminals).............................. 13
Inserting the Batteries............................. 15
Usable Range......................................... 15
Useful Features
Operating with the Remote Control......32
Displaying and Setting the
Break Timer......................................... 32
Displaying the Pointer............................. 32
Using the Spot Function......................... 32
Switching the Eco+Quiet Mode .............. 32
Auto Sync (Auto Sync Adjustment) ......... 33
Freezing a Moving Image........................ 33
Selecting the Picture Mode..................... 33
Displaying an Enlarged Portion of
an Image ............................................. 33
Using the Remote Control as the
Easy Start
Wireless Computer Mouse................... 34
Menu Items...........................................35
Using the Menu Screen........................38
Menu Selections (Quick Start Menu) .........38
Quick Start Menu.................................... 39
Menu Selections (Complete Menu) .......... 39
Picture Adjustment (“Picture” Menu) ....41
Selecting the Picture Mode..................... 41
Adjusting the Image................................ 42
Adjusting the Color Temperature............. 42
Adjusting the Colors ............................... 42
Selecting the Film Mode ......................... 43
Reducing Image Noise (DNR) ................. 43
Eco+Quiet.............................................. 43
Signal Adjustment (“SIG-ADJ” Menu) ..44
Adjusting the Computer Image ............... 44
Resolution Setting .................................. 44
Signal Type Setting................................. 44
Setting the Video System ....................... 45
Setting the Video Setup.......................... 45
Checking the Input Signal....................... 45
Adjusting the Projected Image
(“SCR - ADJ” Menu)...........................46
Setting the Resize Mode......................... 46
Adjusting the Image Position .................. 46
Keystone Correction............................... 46
Setting the Overscan.............................. 47
Setting the On-screen Display ................ 47
Closed Caption ...................................... 47
Selecting the Background Image............ 48
Selecting the Setup Guide...................... 48
Reversing/Inverting Projected Images..... 48
Selecting the Wall Color.......................... 48
Selecting the On-screen Display Language ... 48
Easy Start.............................................16
Setup and Projection.............................. 16
Setup
Setting Up the Projector.......................18
Setting Up the Projector ......................... 18
Standard Setup (Front Projection)........... 18
Screen Size and Projection Distance ...... 19
Projection (PRJ) Mode............................ 20
Ceiling-Mount Setup............................... 20
Connections
Connecting the Projector to
Other Equipment................................21
Controlling the Projector by
a Computer........................................24
Connecting the Power Cord.................24
Using
Basic Operation
Turning the Projector On/Off ................25
Turning the Projector On......................... 25
Turning the Power Off (Putting the
Projector into Standby Mode) .............. 25
Image Projection ..................................26
About the Setup Guide........................... 26
Adjusting the Projected Image................ 26
Correcting Trapezoidal Distortion............ 28
Switching the Input Mode....................... 29
Adjusting the Volume.............................. 29
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projector Function
(“PRJ-ADJ1/2” Menu) ........................49
Auto Sync (Auto Sync Adjustment) ......... 49
Auto Power Off Function ........................ 49
Auto Restart Function............................. 49
Speaker Setting...................................... 49
Selecting the Transmission Speed
(RS-232C) ........................................... 49
Fan Mode Setting................................... 50
System Lock Function............................ 50
Keylock Function.................................... 51
Selecting the Quick Start Menu .............. 51
Setting the FUNCTION Button Operation.. 51
STANDBY Mode..................................... 52
DLP® LinkTM............................................ 52
DLP® LinkTM Invert .................................. 52
Returning to the Default Settings ............ 52
Checking the Lamp Life Status............... 52
Reference
Appendix
Maintenance.........................................53
Maintenance Indicators........................54
Regarding the Lamp.............................56
Lamp...................................................... 56
Caution Concerning the Lamp................ 56
Replacing the Lamp ............................... 56
Removing and Installing the
Lamp Unit............................................ 57
Resetting the Lamp Timer ...................... 58
Connecting Pin Assignments ...............59
RS-232C Specifications and
Commands ........................................61
Computer Compatibility Chart .............66
Troubleshooting....................................67
For SHARP Assistance.........................69
Specifications.......................................70
Dimensions...........................................71
Index.....................................................72
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
CAUTION: Please read all of these instructions before you operate this
product and save these instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered
and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the
safeguards incorporated in this product, observe the following basic rules for its
installation, use and servicing.
1. Read Instructions
10. Ventilation
Slots and openings in the cabinet are provided
All the safety and operating instructions
should be read before the product is
operated.
for ventilation to ensure reliable operation of
the product and to protect it from overheating,
and these openings must not be blocked or
covered. The openings should never be
blocked by placing the product on a bed, sofa,
rug, or other similar surface. This product
should not be placed in a built-in installation
such as a bookcase or rack unless proper
ventilation is provided or the manufacturer's
instructions have been adhered to.
2. Retain Instructions
The safety and operating instructions
should be retained for future reference.
3. Heed Warnings
All warnings on the product and in the
operating instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should
be followed.
11. Power Sources
This product should be operated only from
the type of power source indicated on the
marking label. If you are not sure of the
type of power supply to your home, consult
your product dealer or local power
company. For products intended to operate
from battery power, or other sources, refer
to the operating instructions.
5. Cleaning
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for
example, near a bath tub, wash bowl, kitchen
sink, or laundry tub; in a wet basement; or
near a swimming pool; and the like.
8. Accessories
12. Grounding or Polarization
This product is provided with one of the
following types of plugs. If the plug should
fail to fit into the power outlet, please contact
your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug
with a grounding terminal.
Do not place this product on an unstable
cart, stand, tripod, bracket, or table. The
product may fall, causing serious injury to a
child or adult, and serious damage to the
product. Use only with a cart, stand, tripod,
bracket, or table recommended by the
manufacturer, or sold with the product. Any
mounting of the product should follow the
manufacturer's instructions, and should use a
mounting accessory recommended by the
manufacturer.
This plug will only fit into a grounding
type power outlet.
13. Power-Cord Protection
Power-supply cords should be routed so
that they are not likely to be walked on or
pinched by items placed upon or against
them, paying particular attention to cords
at plugs, convenience receptacles, and the
point where they exit from the product.
9. Transportation
14. Lightning
A product and cart
For added protection for this product during
a lightning storm, or when it is left
unattended and unused for long periods of
time, unplug it from the wall outlet and
disconnect the cable system. This will
prevent damage to the product due to
lightning and power-line surges.
combination should be
moved with care. Quick
stops, excessive force, and
uneven surfaces may
cause the product and cart
combination to overturn.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Overloading
19. Replacement Parts
Do not overload wall outlets, extension cords,
or integral convenience receptacles as this
can result in a risk of fire or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this
product through openings as they may touch
dangerous voltage points or short-out parts
that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
17. Servicing
When replacement parts are required, be
sure the service technician has used
replacement parts specified by the
manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may result in
fire, electric shock, or other hazards.
20. Safety Check
Upon completion of any service or repairs
to this product, ask the service technician
to perform safety checks to determine that
the product is in proper operating
condition.
Do not attempt to service this product
yourself as opening or removing covers
may expose you to dangerous voltage or
other hazards. Refer all servicing to
qualified service personnel.
21. Wall or Ceiling Mounting
This product should be mounted to a wall
or ceiling only as recommended by the
manufacturer.
18. Damage Requiring Service
Unplug this product from the wall outlet
and refer servicing to qualified service
personnel under the following conditions:
a. When the power-supply cord or plug is
damaged.
22. Heat
This product should be situated away from
heat sources such as radiators, heat
registers, stoves, or other products
(including amplifiers) that produce heat.
b. If liquid has been spilled, or objects
have fallen into the product.
c. If the product has been exposed to rain
or water.
d. If the product does not operate normally
by following the operating instructions.
Adjust only those controls that are
covered by the operating instructions,
as an improper adjustment of other
controls may result in damage and will
often require extensive work by a
qualified technician to restore the
product to normal operation.
e. If the product has been dropped or
damaged in any way.
f. When the product exhibits a distinct
change in performance, this indicates a
need for service.
• DLP® and the DLP logo are registered trademarks of Texas Instruments and
BrilliantColorTM and DLP® LinkTM are trademarks of Texas Instruments.
• Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the
United States and/or other countries.
• PC/AT is a registered trademark of International Business Machines Corporation in the
United States.
• Adobe® Reader® is a trademark of Adobe Systems Incorporated.
• Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or
other countries.
• All other company or product names are trademarks or registered trademarks of their
respective companies.
• Some IC chips in this product include confidential and/or trade secret property belonging
to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute,
reverse engineer, reverse assemble or discompile the contents thereof.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Observe the following safeguards when setting up your
projector.
Caution concerning the lamp unit
When using the projector in high-
altitude areas such as mountains (at
altitudes of approximately 1,500
meters (4,900 feet) or more)
■ When you use the projector in high-altitude
areas with thin air, set “Fan Mode” to
“High”. Neglecting this can affect the
longevity of the optical system.
■ Potential hazard of glass particles if lamp
ruptures. In case of lamp rupture, contact
your nearest Sharp Authorized Projector
Dealer or Service Center
for replacement.
See “Regarding the Lamp”
on page 56.
■ Use the projector at altitudes of 2,300
meters (7,500 feet) or less.
Caution concerning the setup of the
projector
Warning about placing the projector in
a high position
■ When placing the projector in a high
position, make certain it is carefully secure
to avoid personal injury caused by the
projector falling down.
■ For minimal servicing and to maintain high
image quality, SHARP recommends that
this projector be installed in an area free
from humidity, dust and cigarette smoke.
When the projector is subjected to these
environments, the vents and lens must be
cleaned more often. As long as the
projector is regularly cleaned, use in these
environments will not reduce the overall
operation life of the unit. Internal cleaning
should only be performed by a Sharp
Authorized Projector Dealer or Service
Center.
Do not subject the projector to hard
impact and/or vibration.
■ Protect the lens so as not to hit or damage
the surface of the lens.
Avoid locations with extremes of
temperature.
■ The operating temperature of the projector
is from 41°F to 95°F (+5°C to +35°C).
■ The storage temperature of the projector is
from –4°F to 140°F (–20°C to +60°C).
Rest your eyes occasionally.
■ Continuously watching the screen for long
hours will cause eye strain. Take regular
breaks to rest your eyes.
Do not set up the projector in places
exposed to direct sunlight or bright light.
■ Position the screen so that it is not in direct
sunlight or room light. Light falling directly
on the screen washes out the colors,
making viewing difficult. Close the curtains
and dim the lights when setting up the
screen in a sunny or bright room.
Do not block the exhaust and intake
vents.
■ Allow at least 11 13
/16 inches (30 cm) of
space between the exhaust vent and the
nearest wall or obstruction.
■ Ensure that the intake vent and the exhaust
vent are not obstructed.
■ If the cooling fan becomes obstructed, a
protection circuit will automatically put the
projector into Standby mode to prevent
overheat damage. This does not indicate a
malfunction. (See pages 54 and 55.)
Remove the projector power cord from the
wall outlet and wait at least 10 minutes.
Place the projector where the intake and
exhaust vents are not blocked, plug the
power cord back in and turn on the
projector. This will return the projector to
the normal operating condition.
Caution regarding placing of the projector
■ Place the projector on a level site within the
adjustment range (9 degrees) of the
adjustment foot.
■ After the projector is purchased, a faint
smell from the vent may appear when the
power is first turned on. This is normal and
is not a malfunction. It will disappear after
the projector is used for a while.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution regarding usage of the projector Using the projector in other countries
■ If you are not to use the projector for a long
time or before moving the projector, make
certain you unplug the power cord from the
wall outlet, and disconnect any other
cables connected to it.
■ Do not carry the projector by holding the
lens.
■ The power supply voltage and the shape of
the plug may vary depending on the region
or country you are using the projector in.
When using the projector overseas, make
sure you use an appropriate power cord for
the country you are in.
Temperature monitor function
■ When storing the projector, ensure that you
close the lens shutter.
■ Do not expose the projector to direct
sunlight or place next to heat sources.
Doing so may affect the cabinet color or
cause deformation of the plastic cover.
■ If the temperature inside the projector
increases, due to blockage of the air vents,
or the setting location, the temperature
warning indicator will blink. And if the
Other connected equipment
■ When connecting a computer or other
audio-visual equipment to the projector,
make the connections AFTER unplugging
the power cord of the projector from the
AC outlet and turning off the equipment to
be connected.
■ Please read the operation manuals of the
projector and the equipment to be
connected for instructions on how to make
the connections.
temperature keeps on rising, “
” will
illuminate in the lower left corner of the
picture with the temperature warning
indicator blinking. If this state continues,
the lamp will turn off, the cooling fan will
run and then the projector will enter
Standby mode. Refer to “Maintenance
Indicators” on pages 54 and 55 for details.
Info
• The cooling fan regulates the internal
temperature, and its performance is automatically
controlled. The sound of the fan may change
during projector operation due to changes in the
fan speed. This does not indicate malfunction.
Closed Caption uses Bitstream Vera fonts
Copyright (c) 2003 by Bitstream, Inc. All Rights Reserved. Bitstream Vera is a trademark of Bitstream, Inc.
Permission is hereby granted, free of charge, to any person obtaining a copy of the fonts accompanying this
license (“Fonts”) and associated documentation files (the “Font Software”), to reproduce and distribute the
Font Software, including without limitation the rights to use, copy, merge, publish, distribute, and/or sell
copies of the Font Software, and to permit persons to whom the Font Software is furnished to do so, subject
to the following conditions:
The above copyright and trademark notices and this permission notice shall be included in all copies of one
or more of the Font Software typefaces.
The Font Software may be modified, altered, or added to, and in particular the designs of glyphs or
characters in the Fonts may be modified and additional glyphs or characters may be added to the Fonts,
only if the fonts are renamed to names not containing either the words “Bitstream” or the word “Vera”.
This License becomes null and void to the extent applicable to Fonts or Font Software that has been
modified and is distributed under the “Bitstream Vera” names.
The Font Software may be sold as part of a larger software package but no copy of one or more of the Font
Software typefaces may be sold by itself.
THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT, TRADEMARK, OR OTHER
RIGHT. IN NO EVENT SHALL BITSTREAM OR THE GNOME FOUNDATION BE LIABLE FOR ANY CLAIM,
DAMAGES OR OTHER LIABILITY, INCLUDING ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
FROM, OUT OF THE USE OR INABILITY TO USE THE FONT SOFTWARE OR FROM OTHER DEALINGS IN
THE FONT SOFTWARE.
Except as contained in this notice, the names of Gnome, the Gnome Foundation, and Bitstream Inc., shall
not be used in advertising or otherwise to promote the sale, use or other dealings in this Font Software
without prior written authorization from the Gnome Foundation or Bitstream Inc., respectively. For further
information, contact: fonts at gnome dot org.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Access the PDF Operation Manuals
PDF operation manuals in several languages are included in the CD-ROM. To
utilize these manuals, you need to install Adobe® Reader® on your computer
(Windows® or Macintosh®).
Please download Adobe® Reader® from the Internet (http://www.adobe.com).
Accessing the PDF Manuals for Windows® (For Macintosh®, skip step 2).
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click the “My Computer” icon.
3 Double click the “CD-ROM” drive.
4 Double click the “MANUALS” folder.
5 Double click the model (name of the folder) that you want to view.
6 Double click the language (name of the folder) that you want to view.
7 Double click the pdf file to access the projector manuals.
Note
• If the desired pdf file cannot be opened by double clicking the mouse, start Adobe® Reader® fi r s t ,
then specify the desired file using the “File”, “Open” menu.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Supplied accessories
Remote control
for XR-55X
<RRMCGA837WJSA> <RRMCGA818WJSA>
Two R-6 batteries
(“AA” size, UM/SUM-3,
HP-7 or similar)
RGB cable
(10' (3.0 m))
<QCNWGA086WJPZ>
for XR-50S
Power cord*
(1)
(2)
(3)
(4)
For U.S. and
Canada, etc.
(6' (1.8 m))
For Europe,
except U.K.
(6' (1.8 m))
For U.K. and
Singapore
(6' (1.8 m))
For Australia, New
Zealand and Oceania
(6' (1.8 m))
<QACCDA007WJPZ> <QACCVA011WJPZ> <QACCBA036WJPZ> <QACCLA018WJPZ>
* Which power cords are supplied along with your projector depends on the region. Use the power
cord that corresponds to the wall outlet in your country.
• Operation manuals (this manual <TINS-E335WJZZ>, OPERATION MANUAL FOR STEREOSCOPIC
3D PROJECTION <TINS-E500WJZZ> and CD-ROM <UDSKAA121WJZZ>)
Note
• Codes in “< >” are Replacement parts codes.
Optional accessories
AN-D350LP
AN-60KT
AN-XRCM30 (for U.S.A. only)
AN-TK201 <for AN-60KT>
AN-TK202 <for AN-60KT>
AN-EP101B <for AN-XRCM30>
(for U.S.A. only)
■ Lamp unit
■ Ceiling-mount adaptor
■ Ceiling-mount bracket
■ Ceiling-mount unit
■ Ceiling-mount extension tube
AN-MR2
AN-C3CP2
AN-A1RS
■ Remote receiver
■ 3 RCA to mini D-sub 15 pin cable (10n (3.0 m))
■
DIN-D-sub RS-232C adaptor (5 57
/64 nn (15 cm))
Note
• Some of the optional accessories may not be available depending on the region. Please check with
your nearest Sharp Authorized Projector Dealer or Service Center.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Numbers in Zrefer to the main pages in this operation manual where the
topic is explained.
10
11
12
13
14
16
17
1
2
3
15
18
19
4
5
6
7
8 9
Front View
Top View
1
Exhaust vent
10 Temperature warning indicator
53
54
2
Zoom ring
11 Lamp indicator
12 Power indicator
27
54
For enlarging/reducing the picture.
54
3
Focus ring
For adjusting the focus.
Lens shutter
26
25
13 STANDBY/ON button
For turning the power on and putting the
projector into Standby mode.
4
5
6
7
8
9
25, 29
HEIGHT ADJUST lever
14 INPUT buttons (P/R)
29
27
15
For switching Input mode.
Adjustment foot
27
15 AUTO SYNC button
33
Remote control sensor
For automatically adjusting images when
connected to a computer.
Speaker
49
Intake vent
16 Adjustment buttons (P/R/O/Q)
53
38
For selecting menu items.
17 ENTER button
38
For setting items selected or adjusted on
the menu.
18 MENU button
38
For displaying adjustment and setting
screens.
19 VOL (Volume) buttons (–O/Q+)
29
For adjusting the speaker sound level.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
6
7
8
12
9
10 11
Rear View (Terminals)
24
22
S-VIDEO input terminal
1
2
RS-232C terminal
Terminal for controlling the projector using a
computer.
6
7
Terminal for connecting video equipment
with an S-video terminal.
USB terminal
VIDEO input terminal
22
34
Terminal connecting with the USB terminal
on the computer for using the supplied
remote control as the computer mouse.
Terminal for connecting video equipment.
AUDIO 2 input terminal
8
9
23
AC socket
Connect the supplied power cord.
24
3
MONITOR OUT terminal
23
(Output terminal for computer RGB and
component signals)
10 Kensington Security Standard
connector
Terminal for connecting a monitor.
11 Rear adjustment foot
27
12 Security bar
4
5
AUDIO 1 input terminal
23
COMPUTER/COMPONENT input
terminal
21, 22
Terminal for computer RGB and component
signals.
Using the Kensington Lock
• This projector has a Kensington Security Standard connector for use with a Kensington
MicroSaver Security System. Refer to the information that came with the system for
instructions on how to use it to secure the projector.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions (Continued)
Numbers in Zrefer to the main pages in this operation manual where the
topic is explained.
34, 32
L-CLICK/EFFECT button
9
1
• For the Left click when with the USB
connection (using a USB cable or the optional
remote receiver).
2
3
14
• For changing the pointer or spot area.
28
10 KEYSTONE button
For entering the Keystone Correction
mode.
4
15
16
17
5
6
7
8
33, 49
11 AUTO SYNC button
For automatically adjusting images when
connected to a computer.
51
12 FUNCTION button
For operating and executing a function
assigned to “FUNCTION Button”.
18
19
20
21
22
9
10
11
12
32
13 ECO+QUIET button
For lowering the noise of the cooling fan
and extending the lamp life.
14 FREEZE button 33
For freezing images.
23
13
29
15 AV MUTE button
For temporarily displaying a black screen
and turning off the sound.
29
16 VOL +/– (Volume) buttons
For adjusting the speaker sound level.
25
1
2
ON button
For turning the power on.
32
17 SPOT button
For displaying the spotlight.
25
STANDBY button
For putting the projector into the Standby
mode.
38
18 ENTER button
For setting items selected or adjusted on
the menu.
29
3
4
5
6
INPUT buttons (
For switching Input mode.
/
)
34, 38
19 R-CLICK/RETURN button
• For the Right click when with the USB
connection (using a USB cable or the optional
remote receiver).
32
BREAK TIMER button
For displaying the break time.
• For returning to the previous menu screen
during menu operations.
33
MAGNIFY buttons
For enlarging/reducing part of the image.
38
20 MENU button
34
PAGE UP/PAGE DOWN buttons
For displaying adjustment and setting
screens.
Same as the [Page Up] and [Page Down]
keys on a computer keyboard, when with
the USB connection (using a USB cable or
the optional remote receiver).
30
21 RESIZE button
For switching the picture size (NORMAL,
16:9, etc.).
32
POINTER button
7
8
22 3D MODE button (XR-55X only)
See the OPERATION MANUAL FOR
STEREOSCOPIC 3D PROJECTION
provided separately.
For displaying the pointer.
MOUSE/Adjustment buttons (P/R/O/Q)
34, 38
• For moving the computer cursor when with the
USB connection (using a USB cable or the
optional remote receiver).
33
23 PICTURE MODE button
• For selecting and adjusting menu items.
For selecting the appropriate picture.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Inserting the Batteries
Pull down the tab on the cover and remove the
cover towards the direction of the arrow.
1
Insert the batteries.
• Insert the batteries making sure the polarities correctly match
the mand nmarks inside the battery compartment.
Insert the lower tab of the cover into the opening,
and lower the cover until it clicks in place.
Incorrect use of the batteries may cause them to leak or explode.
Please follow the precautions below
Caution
• Danger of explosion if battery is incorrectly replaced.
Replace only with alkaline or manganese batteries.
• Insert the batteries making sure the polarities correctly match the mand nmarks inside the battery
compartment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
•
Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.
Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then
remove them using a cloth.
• The batteries included with this projector may run down in a short period, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries.
• Remove the batteries from the remote control if you will not be using the remote control for a long time.
• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
Remote control sensor
Usable Range
The remote control can be used to control the
projector within the ranges shown in the
illustration.
Note
• The signal from the remote control can be
reflected off a screen for easy operation.
However, the effective distance of the signal
may differ depending on the screen material.
30°
30°
When using the remote control
• Ensure that you do not drop it or expose it to
moisture or high temperature.
33n (10 m)
• The remote control may malfunction under a
fluorescent lamp. In this case, move the
projector away from the fluorescent lamp.
Remote control signal
transmitters
Remote control
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Easy Start
This section shows the basic operation (projector connecting with the computer). For details,
see the page described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
3
8
STANDBY/ON
button
8 STANDBY button
ON button
3
O/Qbuttons
6
INPUT buttons
6
INPUT buttons
6
Adjustment
buttons
(P/R/O/Q)
5
6
Zoom ring
4
4
Focus ring
KEYSTONE button
5
HEIGHT
ADJUST lever
4
P. 18
_
1. Place the projector facing a wall or a screen
2.Connect the projector to the computer and plug the power
cord into the AC socket of the projector
When connecting equipment other than a computer, see pages
22 and 23.
_PP. 21, 24
3. Open the lens shutter fully and then turn the projector on
On the projector On the remote control
_P. 25
16
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Adjust the projected image with the Setup Guide
1 After the projector turns on, the Setup Guide appears.
(When “Setup Guide” is set to “On”. See page 48.)
2
Follow the steps in the Setup Guide and adjust the focus, height (angle) and picture size.
3 After adjusting the focus, height (angle) and picture size, press ENTER to finish the
Setup Guide.
_P. 26
5. Correct trapezoidal distortion
Correcting trapezoidal distortion using Keystone Correction.
Shrinks
upper side.
Shrinks
lower side.
On the remote control
_P. 28
6. Select the Input mode
Press INPUT P/Rto display the INPUT list. Use INPUT P/Rto select the Input mode,
and use O/Qto select the audio input terminal.
On the
projector
INPUT list
On the
projector
INPUT
Audio
COMPUTER
S
V
S-VIDEO
VIDEO
On the remote
control
On the remote
control
_P. 29
7. Turn the computer on
8. Turn the power off
Press STANDBY/ON on the projector or STANDBY on the remote control, and then press
the button again while the confirmation message is displayed to put the projector into
Standby mode.
On-screen display
On the
projector
On the remote
control
_P. 25
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Projector
Setting Up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector's
feet flat and level. Doing so will eliminate the need for Keystone correction and provide the best
image quality. (See page 28.)
Standard Setup (Front Projection)
■ Place the projector at the required distance
from the screen according to the desired
picture size. (See page 19.)
Indication of the Projection Image Size and Projection Distance
Example: 4:3 Signal Input (Normal Mode)
Picture Size
300" (762 cm)
240"
×
180"
(610 cm
200" (508 cm)
×
457 cm)
160"
×
120"
100" (254 cm)
(406 cm
80"
×
×
305 cm)
60"
(203 cm
×
40" (102 cm)
152 cm)
32"×
(81 cm24"
×
61 cm)
Projection
Distance
"
"–5'6
"
4'6
(1.4 m – 1.7 m)
"–13'9
11'4
"
"–27'6
(3.5 m – 4.2 m)
"–41–'3
12.6 m)
"
22'8
(6.9 m – 8.4 m)
34'0
(10.4 m
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen Size and Projection Distance
Screen
H
Lens center
L
4:3 Signal Input (Normal Mode)
Picture (Screen) size
Projection distance [L]
Distance from the lens center
χ
Diagonal [ ]
Width
Height
Minimum [L1] Maximum [L2] to the bottom of the image [H]
(7 1/4")
"
"
"
"
"
"
"
"
'
'
'
"
"
"
"
"
"
'
'
'
'
'
'
"
"
"
"
"
"
"
300 (762 cm) 610 cm (240 ) 457 cm (180 ) 10.4 m (34 0 ) 12.6 m (41 3 )
18 cm
15 cm
12 cm
9 cm
7 cm
6 cm
5 cm
4 cm
4 cm
2 cm
(6 1/32")
(4 53/64")
(3 5/8")
"
250 (635 cm) 508 cm (200 ) 381 cm (150 ) 8.6 m (28 4 ) 10.5 m (34 4 )
"
200 (508 cm) 406 cm (160 ) 305 cm (120 ) 6.9 m (22 8 ) 8.4 m (27 6 )
"
"
'
150 (381 cm) 305 cm (120 ) 229 cm (90 )
5.2 m (17 0 ) 6.3 m (20 7 )
(2 57/64")
(2 27/64")
(1 15/16")
(1 11/16")
(1 29/64")
(31/32")
"
"
"
'
120 (305 cm) 244 cm (96 )
183 cm (72 )
152 cm (60 )
122 cm (48 )
107 cm (42 )
91 cm (36 )
61 cm (24 )
4.1 m (13 7 ) 5.0 m (16 6 )
"
"
"
'
100 (254 cm) 203 cm (80 )
3.5 m (11 4 ) 4.2 m (13 9 )
"
"
"
'
"
'
80 (203 cm) 163 cm (64 )
2.8 m (9 1 )
2.4 m (7 11 ) 2.9 m (9 7 )
2.1 m (6 10 ) 2.5 m (8 3 )
1.4 m (4 6 )
3.3 m (11 0 )
"
"
"
'
"
"
'
"
70 (178 cm) 142 cm (56 )
"
"
"
'
'
"
60 (152 cm) 122 cm (48 )
"
"
"
'
"
'
"
40 (102 cm) 81 cm (32 )
1.7 m (5 6 )
16:9 Signal Input (16:9 Mode)
Picture (Screen) size
Projection distance [L]
Minimum [L1] Maximum [L2]
Distance from the lens center
to the bottom of the image [H]
Adjustable range of
image position [S]
χ
Diagonal [ ]
''
Width
Height
(32 13/32")
( 24 33/64")
( 20 27/64")
( 16 11/32")
( 12 1/4")
''
''
''
'
"
'
"
300 (762 cm) 664 cm (261 ) 374 cm (147 ) 11.3 m (37 1 ) 13.7 m (44 11 ) 82 cm
62 cm
''
''
''
'
"
'
"
"
250 (635 cm) 553 cm (218 ) 311 cm (123 ) 9.4 m (30 11 ) 11.4 m (37 5 ) 69 cm (27 )
52 cm
42 cm
31 cm
25 cm
21 cm
17 cm
12 cm
8 cm
(21 39/64")
(16 13/64")
(12 31/32")
(10 51/64")
(8 41/64")
(6 31/64")
(4 21/64")
''
''
'
"
'
"
200 (508 cm) 443 cm (174 ) 249 cm (98 )
7.5 m (24 9 )
9.1 m (29 11 ) 55 cm
'' '' ''
'
"
'
"
150 (381 cm) 332 cm (131 ) 187 cm (74 )
'' '' ''
5.6 m (18 6 )
6.8 m (22 5 ) 41 cm
( 9 13/16")
( 8 11/64")
( 6 17/32")
( 4 29/32")
( 3 17/64")
'
"
'
"
120 (305 cm) 266 cm (105 ) 149 cm (59 )
'' '' ''
4.5 m (14 10 ) 5.5 m (18 0 ) 33 cm
'
"
'
"
100 (254 cm) 221 cm (87 ) 125 cm (49 )
3.8 m (12 4 )
4.6 m (15 0 ) 27 cm
'' '' ''
80 (203 cm) 177 cm (70 ) 100 cm (39 )
'' '' ''
60 (152 cm) 133 cm (52 ) 75 cm (29 )
'' '' ''
40 (102 cm) 89 cm (35 ) 50 cm (20 )
'
"
'
"
3.0 m (9 11 )
3.6 m (12 0 ) 22 cm
'
"
'
"
2.3 m (7 5 )
2.7 m (9 0 )
16 cm
11 cm
'
"
'
"
1.5 m (4 11 )
1.8 m (6 0 )
When using the projector with screen sizes not listed in the above charts, calculate the values according to the formulas.
4:3 Signal 16:9 Signal
[m/cm]
[Feet/inches] [Feet/inches]
[m/cm]
χ
χ
χ
χ
χ
χ
χ
χ
L1: Minimum projection distance (m/ft)
0.03457
0.03457 / 0.3048
0.03766
0.03766 / 0.3048
χ
χ
L2: Maximum projection distance (m/ft)
0.04187
0.06134
—
0.04187 / 0.3048
0.04562
0.27437
0.04562 / 0.3048
χ
χ
H: Distance from the lens center to the bottom of the image (cm/in)
S: Adjustable range of image position (cm/in) See page 46.
0.06134 / 2.54
0.27437 / 2.54
χ
χ
—
0.20754
0.20754 / 2.54
χ
: Picture diagonal size : 40''-300''
Note
• Allow a margin of error in the values in the diagrams above.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Projector (Continued)
Projection (PRJ) Mode
The projector can use any of the 4 projection modes shown in the diagram below. Select the
mode most appropriate for the projection setting in use. (You can set the PRJ mode in “SCR-
ADJ” menu. See page 48.)
■ Table mounted, front projection
■ Ceiling mounted, front projection
[Menu item ➞ “Front”]
[Menu item ➞ “Ceiling + Front”]
■ Ceiling mounted, rear projection
(with a translucent screen)
■ Table mounted, rear projection
(with a translucent screen)
[Menu item ➞ “Rear”]
[Menu item ➞ “Ceiling + Rear”]
a
Ceiling-Mount Setup
It is recommended that you use the optional Sharp ceiling-mount adaptor and unit for this
installation. Before mounting the projector, contact your nearest Sharp Authorized Projector
Dealer or Service Center to obtain the recommended ceiling-mount adaptor and unit (sold
separately).
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector to Other Equipment
Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet
and turn off the equipment to be connected. After making all connections, turn on the projector
and then the other pieces of equipment. When connecting a computer, ensure that it is the last
equipment to be turned on after all the connections are made.
•
For more details of connection and cables, refer to the operation manual of the connecting equipment.
• You may need other cables or connectors not listed below.
Terminals on the Projector
Terminal on
connected equipment
Terminal on the
projector
Equipment
Computer
Cable
RGB cable (supplied)
COMPUTER/
COMPONENT
RGB
output
terminal
Note
• See page 66 “Computer Compatibility Chart” for a list of computer signals compatible with the
projector. Use with computer signals other than those listed may cause some of the functions to not
work.
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest
Macintosh Dealer.
• Depending on the computer you are using, an image may not be projected unless the
computer's external output port is switched on (e.g. Press “Fn” and “F5” keys
simultaneously when using a SHARP notebook computer). Refer to the specific instructions in
your computer's operation manual to enable your computer's external output port.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector to Other Equipment (Continued)
Terminal on
Terminal on the
projector
Equipment
Cable
connected equipment
Video equipment
3 RCA to mini D-sub 15 pin cable
(optional, AN-C3CP2)
COMPUTER/
COMPONENT
Component
video output
terminal
S-video
output
terminal
S-video cable (commercially available)
Video cable (commercially available)
S-VIDEO
VIDEO
Video output
terminal
Camera/Video game
Cables for a camera or a video game/3 RCA to COMPUTER/
mini D-sub 15 pin cable (optional, AN-C3CP2) COMPONENT
Component
video
output
terminal
RCA adaptor plug
(commercially available)
Cables for a camera or a video game
S-VIDEO
VIDEO
S-video
output
terminal
Cables for a camera or a video game
Video
output
terminal
Note
• When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a
commercially available cable that fits in the projector terminal you want to connect.
• The projector does not support RGBC signals via the Euro-scart.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Terminal on
connected equipment
Terminal on the
projector
Equipment
Cable
Audio equipment
ø3.5 mm
ø3.5 mm stereo or mono audio cable
AUDIO 1
audio output (commercially available or available
terminal
as Sharp service part QCNWGA038WJPZ)
RCA audio
output
RCA audio cable (commercially available)
terminal
AUDIO 2
Cables for a camera or a video game
Audio
output
terminal
Monitor
RGB
input
RGB cable (supplied or commercially
available)
MONITOR OUT
terminal
Note
• When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm
stereo audio cable.
• You can select AUDIO 1 or AUDIO 2 in the INPUT list. (See page 29.)
• RGB signals and Component signals can be output to the monitor.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the Projector by a Computer
When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS-
232C adaptor (optional, AN-A1RS) and an RS-232C serial control cable (cross type,
commercially available), the computer can be used to control the projector and check the status
of the projector. See page 61 for details.
When connecting to a computer using a DIN-D-sub RS-232C adaptor (optional,
AN-A1RS) and an RS-232C serial control cable
To RS-232C terminal
DIN-D-sub RS-232C
adaptor (optional, AN-A1RS)
Computer
To RS-232C terminal
RS-232C serial control cable (cross type, commercially available)
Note
• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the
operation manual of the computer for details.
• See pages 59 and 60 for connection of an RS-232C serial control cable.
Info
• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This
may damage your computer or projector.
• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on.
This may damage your computer.
Connecting the Power Cord
Plug the supplied power cord into the
AC socket on the rear of the projector.
Then plug into AC outlet.
AC socket
Power cord
(supplied)
To AC outlet
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the Projector On/Off
Info
Turning the Projector On
• When “Auto Restart” is set to “On”:
If the power cord is unplugged from the outlet
or the breaker switch is turned off when the
projector is on, then the projector
automatically turns on when the power cord
is plugged into the AC outlet or the breaker
switch is turned on. (See page 49.)
• English is the factory default language. If you
want to change the on-screen display to
another language, change the language
according to the procedure on page 48.
Note that the connections to external
equipment and power outlet should be
done before performing the operations
written below. (See pages 21 to 24.)
Open the lens shutter fully and press
STANDBY/ON on the projector or ON
on the remote control.
• The power indicator illuminates green.
• After the lamp indicator illuminates, the projector
is ready to start operation.
Power indicator
Lamp indicator
Note
STANDBY/ON button
• About the Lamp Indicator
The lamp indicator illuminates to indicate the
status of the lamp.
Green: The lamp is on.
Blinking in green: The lamp is warming up.
Red: The lamp is shut down
abnormally or the lamp should be
replaced.
• When switching on the projector, a slight
flickering of the image may be experienced
within the first minute after the lamp has been
illuminated. This is normal operation as the
lamp's control circuitry is stabilising the lamp
output characteristics. It should not be
regarded as faulty operation.
• If the projector is put into Standby mode and
immediately turned on again, the lamp may
take some time to start projection.
• When System Lock is set, the keycode input
box appears. To cancel the keycode setting,
input the keycode that you have already set.
See page 50 for details.
STANDBY
button
ON button
On-screen display (confirmation message)
Turning the Power Off (Putting
the Projector into Standby Mode)
Press STANDBY/ON on the projector
or STANDBY on the remote control,
then press that button again while the
confirmation message is displayed, to
Info
• Direct Power Off function:
You can unplug the power cord from the AC
outlet even if the cooling fan is still running.
put the projector into Standby mode.
• The projector cannot be turned on while cooling.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
Setup Guide screen
About the Setup Guide
After turning on the projector, the Setup
Guide screen appears to assist you with
projector setup.
Guidance items
1 FOCUS
2 HEIGHT ADJUST
3 ZOOM
Press ENTER to exit the Setup Guide
screen.
Note
• The Setup Guide screen automatically
highlights the items in the following order:
1 FOCUS 2 HEIGHT ADJUST
4 ENTER
3 ZOOM
ENTER button
However, you can adjust the focus or height
(angle) regardless of the highlighted item.
• If you do not want to display the Setup Guide
for the next time, set “Menu” - “SCR - ADJ” -
“Setup Guide” to “Off”. (See page 48.)
Adjusting the Projected Image
1 Adjusting the Focus
You can adjust the focus with the focus
ring on the projector.
Rotate the focus ring to adjust the
focus while watching the projected
image.
• Using the knob on the focus ring will make the
adjustments easier.
Focus ring
26
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Adjusting the Height
The height of the projector can be
adjusted using the adjustment feet at the
front and rear of the projector.
When the screen is above the projector,
the projection image can be made higher
by adjusting the projector.
Lift the projector to adjust its
height while lifting the HEIGHT
ADJUST lever.
Make small
adjustments.
HEIGHT ADJUST lever
Remove your hands from the
HEIGHT ADJUST lever of the
projector after its height has
been finely adjusted.
• The angle of projection is adjustable up to
9 degrees from the surface on which the
projector is placed.
Rear adjustment foot
Use the rear adjustment foot to
make the projector level.
• The projector is adjustable 2 degrees
from the standard position.
Info
• Do not apply too much pressure on the
projector when the front adjustment foot
comes out.
Note
•
When lowering the projector, be careful not to
get your fingers caught in the area between
the adjustment foot and the projector.
• When adjusting the height of the projector,
trapezoidal distortion occurs. Follow the
procedures in Keystone Correction to correct
the distortion. (See pages 28 and 46.)
•
Hold the projector firmly while lifting or carrying.
• Do not hold by the lens area.
3 Adjusting the Picture Size
Zoom ring
You can adjust the picture size using the
zoom ring on the projector.
Rotate the zoom ring to enlarge or
shrink the picture size.
• Using the knob on the zoom ring will make the
adjustments easier.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection (Continued)
Correcting Trapezoidal
Distortion
Adjustment buttons
(P/R/O/Q)
When the image is projected either from
the top or from the bottom towards the
screen at an angle, the image becomes
distorted trapezoidally. The function for
correcting trapezoidal distortion is called
Keystone Correction.
Note
RETURN button
• The Keystone Correction can be adjusted up
to an angle of approximately 40 (XR-55X)/
20 (XR-50S) degrees and the screen can
also be set up to an angle of approximately
40 (XR-55X)/ 20 (XR-50S) degrees.
KEYSTONE button
On-screen display
(Keystone Correction mode)
Press KEYSTONE to enter the
Keystone Correction mode.
KEYSTONE
ADJUST
0
END
Shrinks upper side.
(Move the slide bar in the + direction.)
Press P/Qor O/Rto adjust the
Keystone Correction.
Note
Shrinks lower side.
(Move the slide bar in the - direction.)
• To return to the default setting, press
RETURN while the on-screen display of the
Keystone Correction mode is on the screen.
Press KEYSTONE.
• The on-screen display of the Keystone
Correction mode will disappear.
Info
• While adjusting the image using Keystone
Correction, straight lines and the edges of the
image may appear jagged.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching the Input Mode
INPUT buttons
Select the appropriate Input mode for the
connected equipment.
AV MUTE button
Press INPUT
INPUT list.
Use INPUT
/
to display the
VOL +/– (Volume)
buttons
/
to select the Input
mode, and use O/Qto select the
audio input terminal.
O/Qbuttons
Adjusting the Volume
Press VOL +/– on the remote control
or –O/Q+ on the projector to adjust
the volume.
Note
• Pressing VOL–/–Owill lower the volume.
• Pressing VOL+/Q+ will raise the volume.
•
When the projector is connected to external
equipment, the volume level of the external
equipment changes in accordance with the
volume level of the projector. Set the projector's
volume to the lowest level when turning the
projector on/off or when changing the input signal.
On-screen display
• When you do not want to output the sound
from the projector's speaker while the
projector is connected to external equipment,
set “Speaker” in the “PRJ-ADJ1” menu to
“Off”. (See page 49.)
Displaying the Black Screen
and Turning Off the Sound
Temporarily
Press AV MUTE on the remote control
or close the lens shutter to temporarily
display a black screen and turn off the
sound.
On-screen display
Note
• Pressing AV MUTE again will turn the
projected image back on.
•
When you close the lens shutter, the projector will
be set to AV Mute mode and then the projector will
be turned off automatically after about 30 minutes.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection (Continued)
Resize Mode
This function allows you to modify or customize the Resize mode to enhance the input
image. Depending on the input signal, you can choose a desired image.
Press RESIZE.
• See page 46 for setting on menu screen.
RESIZE
button
COMPUTER
Main resolution
SVGA (800 × 600)
XGA (1024 × 768)
SXGA (1280 × 1024)
1280 × 800
NORMAL
FULL
NATIVE
800 × 600
—
BORDER
16:9
1024 × 768
—
768 × 576
XR-55X
XR-50S
1024 × 576
968 × 768
1280 × 1024
1280 × 800
—
720 × 576
922 × 576
1024 × 768
—
1024 × 640
SVGA (800 × 600)
XGA (1024 × 768)
SXGA (1280 × 1024)
1280 × 800
800 × 600
1024 × 768
1280 × 1024
1280 × 800
600 × 450
720 × 450
800 × 450
750 × 600
800 × 500
800 × 600
Input signal
Computer
XR-55X XR-50S
For 4:3 screen
FULL
For 16:9 screen
Image type
NORMAL
NATIVE
BORDER
16:9
Resolution Resolution
lower than lower than
XGA
SVGA
—*2
XGA
SVGA
—*2
*1, *3
*1
4:3 aspect ratio
Resolution Resolution
higher than higher than
XGA
SVGA
SXGA (1280 × 1024)
1280 × 720
5:4 aspect ratio
16:9 aspect ratio
*1
—*2
—*2
1360 × 768
1366 × 768
1280 × 768
*1
*1
*1
1280 × 800
16:10 aspect ratio
: Cutout area on which images cannot be projected
: Area where the signals are off screen
*1 The Image Shift function can be used for these images.
*2 Same as NORMAL mode
*3 For XR-50S model, “Border” cannot be selected with certain resolution selections in which the horizontal part of aspect ratio
becomes smaller than 4:3 (such as 1280 × 1024, among others).
30
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO/DTV
Input signal
For 4:3 screen
AREA ZOOM
For 16:9 screen
BORDER 16:9
Video/DTV
Image type
4:3 aspect ratio
Squeeze
NORMAL
V-STRETCH
*1
*1
*1
*1
*1
*1
480I, 480P,
576I, 576P,
NTSC, PAL,
SECAM
Letter box
720P, 1035I,
1080I, 1080P
*1
16:9 aspect ratio
16:9 aspect ratio
—*2
—*2
*1
540P
(4:3 aspect ratio in 16:9)
: Cutout area on which images cannot be projected
: Area on which the image is not included in the original signals
*1 The Image Shift function can be used for these images.
*2 Same as NORMAL mode.
About Copyrights
• When using the Resize function to select an image size with a different aspect ratio to a TV
program or video image, the image will look different from its original appearance. Keep this
in mind while choosing an image size.
• The use of the Resize or Keystone Correction function to compress or stretch the image for
commercial purposes/public displays in a café, hotel, etc. may be an infringement of
copyright protected by law for copyright holders. Please use caution.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating with the Remote Control
BREAK TIMER button
Displaying the Pointer
FREEZE button
MAGNIFY buttons
Press POINTER and press P/R/
O/Qon the remote control to
POINTER button
SPOT button
move the pointer.
• Press EFFECT to change the pointer icon
(5 types).
Star
Finger1
Finger2
Heart
Underline
Adjustment buttons
(P/R/O/Q)
EFFECT button
PICTURE MODE button
Press POINTER again.
2
ECO+QUIET button
AUTO SYNC button
• The pointer will disappear.
Using the Spot Function
Displaying and Setting the
Break Timer
Press SPOT and press P/R/O/Q
on the remote control to move
the spot area.
Press BREAK TIMER.
• Press EFFECT to change the spot area
size (3 types).
• The timer starts to count down from 5
minutes.
1/9
1/25
1/8
On-screen display
Press P/R/O/Qto adjust the
Press SPOT again.
• The spot area will disappear.
length of the break time.
•Increases with Por Q
5 minutes ➞ 6 minutes ➞ 60 minutes
•Shortens with Oor R
4 minutes ➞ 3 minutes ➞1 minute
• The break time can be set in units of one
minute (up to 60 minutes).
Switching the Eco+Quiet
Mode
Canceling the break timer display function
Press ECO+QUIET to switch the
Press BREAK TIMER.
Eco+Quiet mode between on and off.
• When the Eco+Quiet Mode is set to “ON”, the
sound of the cooling fan will turn down, the power
consumption will decrease, and the lamp life will
extend.
Note
• The Break Timer is not available while the
projector is operating the following functions.
- Auto Sync
- Freeze
- AV Mute
Note
• Refer to “Eco+Quiet” on page 43 for details.
- Input Search
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto Sync
(Auto Sync Adjustment)
Displaying an Enlarged
Portion of an Image
Auto Sync function works when detecting Graphs, tables and other portions of
input signal after the projector turns on.
projected images can be enlarged. This
is helpful when providing more detailed
explanations.
Press AUTO SYNC to manually adjust
with Auto Sync function.
Press
MAGNIFY on the
remote control.
Note
• Enlarges the image.
• When the optimum image cannot be achieved
with Auto Sync adjustment, use manual
adjustments. (See page 44.)
• Pressing
or reduces the projected image.
or
MAGNIFY enlarges
Note
Press
.
×1 ×2 ×3 ×4
Freezing a Moving Image
Press
.
Press FREEZE.
• You can change the location of the
enlarged image using P, R, Oand Q.
• The projected image is frozen.
Press FREEZE again to return to
the moving image from the
currently connected device.
2
Press RETURN on the remote
control to cancel the operation.
• The magnification then returns to ×1.
Note
• The selectable magnifications differ
depending on the input signal.
• In the following cases, the image will
return to the normal size (×1).
- When switching the Input mode.
- When RETURN has been pressed.
- When the input signal is changed.
- When the input signal resolution and
refresh rate (vertical frequency)
change.
Selecting the Picture Mode
You can select the appropriate Picture
mode for the projected image, such as
movie or video game.
Press PICTURE MODE.
• When pressing PICTURE MODE, the Picture
mode changes in the following order:
- When the Resize mode is changed.
STANDARD
PRESENTATION
MOVIE GAME sRGB
*
Note
• See page 41 for details on the Picture mode.
*
“sRGB” is displayed only when RGB signal is input.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating with the Remote Control (Continued)
Using the Remote Control as the Wireless Computer Mouse
When connecting the projector and the computer with a USB cable, you can use the
remote control as the computer mouse.
If the computer is placed too far away from the projector to be connected via the USB
cable, the remote receiver (optional, AN-MR2) makes it possible to operate the
projector with the remote control. For details, see the operation manual of the
receiver.
Connecting with a USB cable
Computer
R
emote receiver
To USB terminal
(optional, AN-MR2)
To USB terminal
or
USB cable
(commercially available or available as
Sharp service part QCNWGA014WJPZ)
PAGE UP/
PAGE DOWN buttons
The mouse pointer can be
operated in the following way
after it is connected.
MOUSE/Adjustment
buttons (ꢀ/ꢁ/?/_)
■ When moving the cursor
Press MOUSE/Adjustment buttons (P/R/O/Q).
■ When left-clicking
Press L-CLICK.
■ When right-clicking
R-CLICK button
L-CLICK button
Press R-CLICK.
■
When your computer supports only a
one-click mouse (such as Macintosh)
Press L-CLICK or R-CLICK.
L-CLICK and R-CLICK have common function.
■
When using [Page Up] or [Page Down]
Same as the [Page Up] and [Page Down] keys
on a computer keyboard.
Press PAGE UP or PAGE DOWN.
Note
• This function only works with the Microsoft® Windows® OS and Mac OS® that support USB.
• You cannot use this function when displaying the menu screen.
• Confirm that the computer recognizes the USB connection.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Items
The following shows the items that can be set in the projector.
“Quick Start Menu”
“Picture” menu
Main menu
Sub menu
Main menu
Sub menu
Standard
Presentation
Movie
Game
sRGB*1
Picture
Picture Mode
Quick Start Menu
Input Search Start
Page 41
Page 41
Page 39
Resolution
Page 39
Contrast
-30 +30
-30 +30
Resize
Normal
Full
Bright
Color
Tint
Native
Area Zoom
V-Stretch
Border
16:9
Page 39
-30 +30 *2
*2
-30 +30
Sharp
Red
-30 +30 *2
-30 +30
Keystone
-80 +80
Page 39
Blue
-30 +30
Eco + Quiet [On/Off]
Page 39
Language
Page 42
English
polski
Deutsch
Español
Nederlands
Français
Italiano
Magyar
Türkçe
Page 39
CLR Temp
-1
0
1
2
Page 42
BrilliantColor™
Page 42
C.M.S. Setting [On/Off]
Page 42
C.M.S.
Svenska
Português
Information
Page 39
Go To Complete Menu
Page 39
Page 42
Film Mode
Auto
Off
*2
Page 43
DNR
Level 1
Level 2
Level 3
Page 43
Eco+Quiet [On/Off]
Page 43
Reset
C.M.S.-Hue
R
-30 +30
Y
-30 +30
-30 +30
-30 +30
-30 +30
-30 +30
Page 42
C.M.S.-Saturation
G
C
Page 42
C.M.S.-Value
B
M
Page 42
Reset
Reset
Return
*1 Item when inputting RGB signal through
COMPUTER.
*2 Items when inputting component signal through
COMPUTER, or when selecting S-VIDEO or VIDEO.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Items (Continued)
“Signal adjustment (SIG-ADJ)” menu
“Screen adjustment (SCR-ADJ)” menu
Main menu
SIG-ADJ
Sub menu
Main menu
SCR - ADJ
Sub menu
Clock
Phase
H-Pos
V-Pos
Reset
-150 +150 *3
-30 +30 *3
-150 +150
Resize
Normal
Full
Page 44
Page 46
Page 46
Native
Area Zoom
V-Stretch
Border
16:9
*4
Image Shift
-96 +96 *7
-75 +75 *8
-60
+60 *4
*4
Page 46
Page 44
Keystone
-80 +80 *7
-40 +40 *8
Resolution
Page 44
Signal Type
Page 46
Auto
RGB
*5
*6
Overscan [On/Off]
YPbPr
Page 44
Video System
Page 47
Auto
PAL
OSD Display [On/Off]
SECAM
NTSC4.43
NTSC3.58
PAL-M
PAL-N
Page 45
Page 47
Off
CC1
CC2
Closed Caption
Page 47
PAL-60
Background
Logo
Blue
None
Video Setup
0 IRE
7.5 IRE
Page 48
Page 45
Signal Info
Setup Guide [On/Off]
Page 48
Page 45
PRJ Mode
Front
Ceiling + Front
Rear
*3 Items when inputting RGB signal through
COMPUTER/COMPONENT.
*4 Items when inputting COMPUTER/COMPONENT.
*5 Item when selecting COMPUTER/COMPONENT.
*6 Item when selecting S-VIDEO or VIDEO.
Page 48
Ceiling + Rear
Wall Color
Off
Blackboard
Whiteboard
Page 48
English
polski
Language
Deutsch
Español
Nederlands
Français
Italiano
Magyar
Türkçe
Page 48
Svenska
Português
*7 Adjustment range for XR-55X.
*8 Adjustment range for XR-50S.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
“Projector adjustment (PRJ-ADJ1/2)” menu
Main menu
PRJ-ADJ1
Sub menu
Auto Sync [On/Off]
Page 49
Page 49
Auto Power Off [On/Off]
Page 49
Auto Restart [On/Off]
Page 49
Speaker [On/Off]
Page 49
RS-232C
9600bps
38400bps
115200bps
Page 49
Fan Mode
Normal
High
Page 50
System Lock
[Enable/Disable]
Page 50
Keylock [On/Off]
Page 51
Main menu
PRJ-ADJ2
Sub menu
Quick Start Menu [On/Off]
Page 49
Page 51
FUNCTION Button
Input Search
Audio Mute
Image Shift
Signal Info
Page 51
STANDBY Mode
Quick Start
Eco
Page 52
DLP® LinkTM [On/Off]
*9
*9
Page 52
DLP® LinkTM Invert
Page 52
All Reset
Page 52
Lamp Timer (Life)
Page 52
*9 This item is available for XR-55X only.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menu Screen
Select from the Quick Start Menu, which is a collection of the most frequently used
functions, or the Complete Menu, which enables advanced settings and adjustments.
Adjustment buttons (P/R/O/Q)
ENTER button
MENU button
ENTER button
Adjustment buttons
(P/R/O/Q)
RETURN button
• Press RETURN to return
to the previous screen
when the menu is
displayed.
MENU button
Menu Selections (Quick Start Menu)
• This operation can also be performed by using the buttons on the projector.
Example
Press MENU.
• The “Quick Start Menu” screen for the
selected Input mode is displayed.
Quick Start Menu
1024×768
Input Search Start
Resolution
Normal
Resize
Press Por Rto select the
Keystone
Eco+Quiet
Language
Information
0
desired item, then press ENTER.
Off
English
Press P/R/O/Qto adjust the
item selected, then press
ENTER.
Go To Complete Menu…
Info
SEL./ADJ.
ENTER
END
• To display the advanced settings and
adjustments, select “Go To Complete Menu”.
Press ENTER to display the Complete Menu
screen.
•
If you do not want to display the Quick Start
Menu, set “Go To Complete Menu” - “PRJ-ADJ2”
- “Quick Start Menu” to “Off”. (See page 51.)
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Menu
The following items can be configured on the Quick Start Menu.
Selectable items
Input Search Start
Description
Automatically searches for and switches to the appropriate Input mode.
Pressing an operation button during input searching cancels the search.
Resolution
Resize
Manually change the resolution.
Use this function when the image and screen size do not match with the
resolution selected automatically. (See page 44.)
Changes the Resize mode.
Use this function to stretch the image vertically or horizontally or when the
edges of the image cannot be seen. (See page 46.)
Keystone
Eco+Quiet
Corrects the keystone distortion of projected images.
Use this function to correct the trapezoidal distortion of images caused when
projecting images at an angle to the screen. (See page 46.)
When set to “On”, this function reduces the cooling fan noise and power
consumption, thereby prolonging the operating life of the lamp. (See page 43.)
Language
Selects the language displayed on the screen. (See page 48.)
Displays the input signal, lamp use time, remaining lamp life, etc.
Displays the Complete Menu for advanced settings and adjustments.
Information
Go To Complete Menu
Note
• The setting of Resize mode will be made independently for each Input mode.
The setting of Eco+Quiet mode will be made independently for each Input mode and each Picture mode.
•
Menu Selections (Complete Menu)
Example: Adjusting “Bright”.
• This operation can also be performed by using the buttons on the projector.
Example: “Picture” screen menu for
Press MENU.
COMPUTER (RGB) input
• The “Quick Start Menu” screen is
displayed.
Menu item
Picture
SIG
SCR
PRJ1
PRJ2
Press Por Rto select “Go To
Picture Mode
Contrast
Bright
Standard
Complete Menu”.
0
0
0
0
0
1
Red
Press Qor Oand select
“Picture” to adjust.
Blue
CLR Temp
BrilliantColorTM
C.M.S. Setting
C.M.S.
DNR
Eco+Quiet
Reset
On
Info
Level 2
Off
• When “PRJ-ADJ2” - “Quick Start Menu” is
set to “On”, pressing MENU displays the
Quick Start Menu screen.
SEL./ADJ.
ENTER
END
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menu Screen (Continued)
Press Por Rand select “Bright”
Picture
SIG
SCR
PRJ1
PRJ2
4
to adjust.
Picture Mode
Contrast
Bright
Standard
• The selected item is highlighted.
0
0
0
0
0
1
Red
Blue
CLR Temp
BrilliantColorTM
C.M.S. Setting
C.M.S.
On
DNR
Eco+Quiet
Reset
Level 2
Off
SEL./ADJ.
Single ADJ
END
Items to be adjusted
PRJ1
PRJ2
SIG
Pict.
SCR-ADJ
Resize
Normal
To adjust the projected
image while watching it
Image Shift
Keystone
0
0
Press ENTER.
• The selected item (e.g. “Bright”) is
displayed by itself at the bottom of the
screen.
Press ENTER.
• When pressing Por R, the following item
(“Red” after “Bright”) will be displayed.
The item displayed by itself
Picture
Bright
0
Note
SEL./ADJ.
Rtn. Menu
END
• Press ENTER again to return to the
previous screen.
Picture
SIG
SCR
PRJ1
PRJ2
Press Oor Qto adjust the item
Picture Mode
Contrast
Bright
Standard
selected.
0
1 5
0
• The adjustment is stored.
Red
Blue
CLR Temp
BrilliantColorTM
0
0
1
On
C.M.S. Setting
C.M.S.
DNR
Eco+Quiet
Reset
Level 2
Off
Press MENU.
• The menu screen will disappear.
SEL./ADJ.
Single ADJ
END
Note
• The MENU button is not available while the projector is operating:
- Auto Sync/Break Timer/Freeze/AV Mute/Input Search
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustment (“Picture” Menu)
Menu operation n Page 39
Q PAGE1
Q PAGE2
Picture
SIG
SCR
PRJ1
PRJ2
Picture
SIG
SCR
PRJ1
PRJ2
1
Picture Mode
Contrast
Bright
Color
Standard
Picture Mode
Standard
0
0
0
0
0
0
0
0
1
CLR Temp
3
2
BrilliantColorTM
C.M.S. Setting
C.M.S.
Tint
On
2
4
Sharp
Red
5
6
7
Film Mode
DNR
Auto
Level 2
Off
Blue
Eco+Quiet
Reset
SEL./ADJ.
ENTER
END
SEL./ADJ.
ENTER
END
Selecting the Picture Mode
1
The default settings of each item when selecting Picture Mode
Selectable
items
Description
CLR Temp
BrilliantColorTM
Eco+Quiet
Off
Standard
For standard image
0
0
1
2
Presentation Brightens portions of image for
more enhanced presentations.
Off
Movie
Game
*sRGB
Gives natural tint to the
projected image.
–1
0
0
1
–
On
Off
Off
Gives sharpness to the
projected image.
For high fidelity reproduction of
images from a computer.
–
• “sRGB” is displayed only when RGB signal is input.
• You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are
retained in memory.
Note
•
You can also press PICTURE MODE on the remote control to select the Picture mode. (See page 33.)
• *sRGB is an international standard of color reproduction regulated by the IEC (International
Electrotechnical Commission). As the fixed color area has been decided by the IEC, the images are
displayed in a natural tint based on an original image, when “sRGB” is selected.
You cannot set the items, “Red”, “Blue”, “CLR Temp”, “BrilliantColorTM”, when “sRGB” is selected.
Info
• When “sRGB” is selected, the projected image may become dark, but this does not indicate a
malfunction.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustment (“Picture” Menu)
(Continued)
Menu operation n Page 39
Adjusting the Image
Adjusting the Colors
2
4
This function adjusts each of the six main
colors that comprise the color wheel, altering
their “Hue”, “Saturation”, or “Value”.
Adjustment
items
Contrast
Obutton
Qbutton
For less
contrast.
For less
brightness.
For less color
intensity.
For making skin For making skin
tones purplish.
For less
sharpness.
For weaker red. For stronger
red.
For weaker
blue.
For more
contrast.
For more
brightness.
For more color
intensity.
Selectable items
Description
Bright
Color*1
Tint*1
C.M.S.-Hue
Sets the hue of the main colors.
C.M.S.-Saturation Sets the saturation of the main
colors
C.M.S.-Value
Sets the brightness of the main
colors.
tones greenish.
For more
sharpness.
Sharp*1
Red*2
Reset
The adjustments of “Hue”,
“Saturation” and “Value” of all
colors are reset to the default
setting.
Blue*2
For stronger
blue.
Return
Returns to the “Picture” menu
screen.
BrilliantColor™*2 *3 For making the For making the
effect weaker.
effect stronger.
Adjusting “Hue”, “Saturation”, or “Value”.
*1 Not displayed in the RGB input mode.
*2 Not adjustable/selectable when selecting “sRGB”.
*3 BrilliantColor™ uses Texas Instruments'
BrilliantColor™ technology. As the BrilliantColor™
level is increased, the image becomes brighter
while the color reproduction is kept at a high level.
1 Select “On” for “C.M.S. Setting” in the “Picture”
menu and then press ENTER.
2 Select “C.M.S.” in the “Picture” menu and then
press ENTER.
3 Press Por Rto select either “Hue”, “Saturation”, or
“Value” and then press ENTER.
Note
4 Select the color to be adjusted with Por Rand
adjust it with Oor Q.
• “Red”, “Blue”, “BrilliantColorTM” and “CLR
Temp” cannot be set when “sRGB” is
selected.
Example of adjusting the “Hue”
• To reset all adjustment items, select “Reset”
and press ENTER.
Main colors
R (Red)
Obutton
Qbutton
Closer to magenta Closer to yellow
Y (Yellow)
G (Green)
C (Cyan)
B (Blue)
Closer to red
Closer to green
Closer to cyan
Closer to blue
Closer to magenta
Closer to red
Closer to yellow
Closer to green
Closer to cyan
Adjusting the Color
Temperature
3
M (Magenta) Closer to blue
Selectable
items
Description
• When “Saturation” is selected, the selected
color becomes
O: lighter. Q: thicker.
• When “Value” is selected, the selected color
becomes
For lower color temperature for
warmer, reddish incandescent-like
images.
–1
0
O: darker. Q: brighter.
1
For higher color temperature for
cooler, bluish, fluorescent-like images.
• To reset the adjustment values of each color to
the default settings, select “Reset” and press
ENTER.
Note
• Values on “CLR Temp” are only for general
standard purposes.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu operation n Page 39
Selecting the Film Mode
Eco+Quiet
5
7
This function provides high-quality playback
of images originally projected at 24 fps, such
as movies on DVDs.
Selectable
items
Brightness and Power consumption
On
Off
Approx. 75%
100%
Selectable
Description
items
Auto
Off
Films are detected automatically.
Films are not detected.
Note
• When “Eco+Quiet” is set to “On”, the fan
sound and power consumption are lower than
they are when “Off” is selected. (Projection
brightness decreases as shown in the chart.)
Note
• This function is available for the following
signals.
With COMPUTER/COMPONENT input:
- 480I
- 576I
- 1035I (XR-55X only)
- 1080I (XR-55X only)
With S-VIDEO or VIDEO input:
- All signals
Reducing Image Noise (DNR)
6
Video digital noise reduction (DNR) provides
high quality images with minimal dot crawl
and cross color noise.
Selectable
Description
items
Level 1
Sets the DNR level for viewing a
clearer picture.
Level 2
Level 3
Note
• This function is not available for some signals.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Signal Adjustment (“SIG-ADJ” Menu)
Menu operation n Page 39
Pict.
SIG-ADJ
SCR
PRJ1
PRJ2
Clock
Phase
H-Pos
V-Pos
0
0
0
0
1
Reset
Resolution
1024 x 768
Auto
2
3
Signal Type
Video System
Video Setup
Auto
4
5
0 IRE
Signal Info 1024 x 768
48.3 kHz 60.0 Hz
6
H
/
V
SEL./ADJ.
ENTER
END
Adjusting the Computer Image
Signal Type Setting
1
3
If the optimum image cannot be obtained with
Auto Sync adjustment, use the SIG-ADJ function.
This function allows you to select the input signal
type RGB or Component for COMPUTER/
COMPONENT.
Selectable
Description
items
Selectable
Description
items
Clock
Phase
Adjusts vertical noise.
Auto
Input signals are automatically
recognized as RGB or component.
Adjusts horizontal noise (similar to
tracking on your VCR).
RGB
Set when RGB signals are received.
H-Pos
V-Pos
Centers the on-screen image by
moving it to the left or right.
YPbPr
Set when Component signals are
received.
Centers the on-screen image by
moving it up or down.
Note
• To reset all adjustment items, select “Reset”
and press ENTER.
• The adjustable range of “H-Pos” (H-Position)
and “V-Pos” (V-Position) may vary depending
on the screen resolution of the computer.
Resolution Setting
2
Ordinarily, the type of input signal is detected and
the correct Resolution mode is automatically
selected. However, for some signals, the optimal
Resolution mode in “Resolution” may need to be
selected to match the computer display mode.
Note
• See “Checking the Input Signal” on page 45
for information on the currently selected input
signal.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu operation n Page 39
Setting the Video System
Checking the Input Signal
4
6
The video input system mode is factory preset
to “Auto”; however, a clear picture from the
connected audio-visual equipment may not be
received, depending on the Video signal
difference.
This function allows you to check the current
input signal information.
In that case, switch the Video signal.
Selectable items
Auto
PAL
SECAM
*NTSC4.43
NTSC3.58
PAL-M
PAL-N
PAL -60
* When reproducing NTSC signals in PAL
video equipment.
Note
• The Video signal can only be set in S-VIDEO
or VIDEO mode.
• When “Video System” is set to “Auto”, you
may not receive a clear picture due to signal
differences. Should this occur, switch to the
video system of the source signal.
Setting the Video Setup
5
Selectable
items
Description
0 IRE
Sets the black level to 0 IRE.
Sets the black level to 7.5 IRE.
7.5 IRE
Note
• This function is available for the following
signals.
With COMPUTER/COMPONENT input:
- 480I
With S-VIDEO or VIDEO input:
- NTSC3.58
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projected Image (“SCR-ADJ” Menu)
Menu operation n Page 39
Pict.
SIG
SCR-ADJ PRJ1
PRJ2
Resize
Normal
1
2
3
4
5
6
7
8
9
0
Image Shift
Keystone
Overscan
OSD Display
Closed Caption
Background
Setup Guide
PRJ Mode
0
0
On
On
Off
Logo
On
Front
Off
Wall Color
Language
English
SEL./ADJ.
ENTER
END
Setting the Resize Mode
Keystone Correction
1
3
Use this function to stretch the image
vertically or horizontally or when the edges of
the image cannot be seen.
When the image is projected either from the top
or from the bottom towards the screen at an
angle, the image becomes distorted trapezoidally.
The function for correcting trapezoidal distortion
is called Keystone Correction.
Note
Select “Keystone” on the “SCR-ADJ”
menu and adjust with the slide bar.
See page 28 for details of Keystone Correction.
• For details of the Resize mode, see pages
30 and 31.
• You can also press RESIZE on the remote
control to set the Resize mode. (See page 30.)
Qbutton
Obutton
Adjusting the Image
Position
2
You can move the projected image vertically.
Note
• The Keystone Correction can be adjusted up
to an angle of approximately 40 (XR-55X)/
20 (XR-50S) degrees.
• You can also press KEYSTONE on the
remote control to adjust Keystone Correction.
Obutton
Qbutton
Note
• This function only works in some Resize
modes. (See pages 30 and 31.)
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu operation n Page 39
Setting the Overscan
Closed Caption
4
6
This function allows you to set the overscan area
(display area).
<For Americas only>
Info
Selectable
Description
items
• This function is available for NTSC3.58 signal.
• This function does not work when the Resize
mode is set to “Border”.
• This function is available in the following cases
only:
On
The input area is displayed without the
screen edges.
Off
The whole input area is displayed.
Resize mode
Keystone Correction
-40 − +40
Note
Normal
Area Zoom
V-Stretch
• This function is available for the following
signals.
16:9
-12 − +12
With COMPUTER/COMPONENT input:
- 480P
- 540P
- 576P
- 720P
- 1035I
• “Closed Caption” is a system which allows
conversations, narration, and sound effects in TV
programs (Limited regions) and home videos to
be viewed as captions on the screen.
- 1080I/1080P
• If noise appears at the screen edges when
“Off” is selected, set the function to “On”.
• Also see “About Copyrights” on page 31.
• Not all programs and videos will offer closed
captioning. Please look for the
symbol to
ensure that captions will be shown.
• Two channels are available: CC1 and CC2.
Setting the On-screen
Display
5
Selectable
Description
items
Off
—
Selectable
items
CC1
CC2
Closed Caption mode for CH1 data
Closed Caption mode for CH2 data
Description
On
Off
All on-screen displays are displayed.
VOLUME/AV MUTE/FREEZE/AUTO
SYNC/RESIZE/PICTURE MODE/
ECO+QUIET/MAGNIFY/Input Search/
Audio Mute/“An invalid button has
been pressed.” are not displayed.
Note
•
Closed Caption may malfunction (white blocks,
strange characters, etc.) if signal conditions are
poor or if there are problems at the broadcast
source. This does not necessarily indicate a
problem with the projector.
• If any button is pressed to call up the on-
screen display while viewing a Closed Caption
broadcast, the closed captions will disappear.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projected Image (“SCR-ADJ” Menu)
(Continued)
Menu operation n Page 39
Selecting the Background
Image
7
Selecting the Wall Color
This function allows you to project the image
to a colored (white or dark green) surface or
wall without using a screen.
0
Selectable items
Description
Sharp logo screen
Logo
Blue
Selectable items
Description
Blue screen
—
Off
The Wall Color function is not
activated.
None
Blackboard
Whiteboard
Projects images onto a
blackboard (dark green).
Selecting the Setup Guide
8
Projects images onto a
whiteboard.
Selectable items
Description
On
Displaying the Setup Guide
when turning the projector on.
Selecting the On-screen
Display Language
Off
Not displaying the Setup Guide.
The projector can switch the on-screen
display language among 17 languages.
Reversing/Inverting
Projected Images
9
English
polski
Deutsch
Español
Nederlands
Français
Italiano
Magyar
Türkçe
Selectable items
Description
Front
Normal image (Projected from
the front of the screen)
Ceiling + Front
Rear
Inverted image (Projected from
the front of the screen with an
inverted projector)
Svenska
Português
Reversed image (Projected from
the rear of the screen or with a
mirror)
Ceiling + Rear
Reversed and inverted image
(Projected with a mirror)
See page 20 for details of Projection (PRJ) Mode.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projector Function (“PRJ-ADJ1/2” Menu)
Menu operation n Page 39
Q PRJ-ADJ1
Q PRJ-ADJ2
Pict.
SIG
SCR
PRJ1 PRJ-ADJ2
On
Pict.
SIG
SCR PRJ-ADJ1 PRJ2
9
0
Quick Start Menu
1
2
3
4
5
6
7
8
Auto Sync
On
Auto Power Off
Auto Restart
Speaker
On
FUNCTION Button
STANDBY Mode
Input Search
Quick Start
On
On
RS-232C
9600bps
Normal
Disable
Off
Fan Mode
System Lock
Keylock
DLP® Link TM
DLP® Link TM Invert
All Reset
Off
Lamp Timer(Life)
SEL./ADJ.
0
h
0
min 100%
END
ENTER
SEL./ADJ.
ENTER
END
Auto Sync (Auto Sync
Adjustment)
1
Auto Restart Function
3
Selectable
items
Description
Selectable
items
Description
On
If the power cord is unplugged from the
outlet or the breaker switch is turned off
when the projector is on, then the
projector automatically turns on when
the power cord is plugged into the AC
outlet or the breaker switch is turned on.
On
Auto Sync adjustment will occur when
the projector is turned on or when the
input signals are switched, when
connected to a computer.
Off
Auto Sync adjustment is not
automatically performed.
Off
The projector does not turn on
automatically when the power cord is
plugged into the AC outlet or the
breaker switch is turned on.
Note
• Auto Sync adjustment is also performed by
pressing AUTO SYNC.
• The Auto Sync adjustment may take some
time to complete, depending on the image of
the computer connected to the projector.
• When the optimum image cannot be achieved
with Auto Sync adjustment, use manual
adjustments. (See page 44.)
Speaker Setting
4
Selectable
items
Description
On
The audio signal is output from the
internal speaker.
Off
The audio signal is not output from the
internal speaker.
Auto Power Off Function
2
Selectable
items
Description
Selecting the Transmission
Speed (RS-232C)
Make sure that both the projector and
computer are set for the same baud rate.
5
On
Off
When no input signal is detected for
more than 15 minutes, the projector will
automatically enter Standby mode.
The Auto Power Off function will be
disabled.
Selectable
Description
items
Note
9600bps
Transmission speed is slow.
• When the Auto Power Off function is set to
“On”, 5 minutes before the projector enters
Standby mode, the message “Enter STANDBY
mode in X min.” will appear on the screen to
indicate the remaining minutes.
38400bps
115200bps Transmission speed is rapid.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projector Function (“PRJ-ADJ1/2” Menu)
(Continued)
Menu operation n Page 39
Fan Mode Setting
6
Note
This function changes the fan rotation speed.
•
If you input a wrong keycode, the cursor returns to
the first point of the “Old Code”.
Selectable
Description
items
• The preset keycode is 4 Rbuttons on the
projector. When you press the Rbutton four
times, the keycord input screen disappears.
Normal
High
Suitable for normal environments.
Set when using the projector at
altitudes of approximately 1,500 meters
(4,900 feet) or more.
Press the 4 buttons on the remote
control or on the projector to enter
the new keycode in “New Code”.
When “Fan Mode” is set to “High”, the fan rotation
speeds up, and the fan noise becomes louder.
Note
System Lock Function
7
• You cannot use the following buttons
for keycode: STANDBY/ON, ON,
STANDBY, ENTER, L-CLICK, R-
CLICK/RETURN and MENU
System Lock function recognizes
each button on the remote control
or on the projector as an individual
button, even if they share the same
button name. If you used the buttons
on the projector in setting your
keycode, the keycode cannot be
canceled with the remote control.
This function prevents unauthorized use of the
projector. Once this function is activated,
users must enter the correct keycode each
time the projector is turned on. We suggest
you record the keycode in a safe place
where only authorized users have access.
•
Info
• If you lose or forget your keycode, contact
your nearest Sharp Authorized Projector
Dealer or Service Center (see page 69). Even
if the product warranty is valid, the keycode
reset will incur a charge.
PRJ - ADJ1
Setting the System Lock
Old Code
New Code
Reconfirm
* * * *
–
–
–
–
–
–
–
–
a
Setting/Changing the Keycode
Select “System Lock”, then press
ENTER or Q.
Enter the same keycode in “Re-
confirm”.
Select “Next”, then press ENTER.
• The screen for entering the keycode
appears.
Note
To cancel the keycode that you have
already set
• Press Ron the projector for four times in
steps 4 and 5 above.
When the System Lock is set
• When System Lock is set, the keycode input
screen appears after the power is turned on.
When it appears, enter the right keycode to
start projection.
Press the 4 buttons on the remote
control or on the projector to enter
the preset keycode in “Old Code”.
• When setting the keycode for the first time,
press Ron the projector for four times.
PRJ - ADJ1
Setting the System Lock
–
–
–
–
–
–
–
–
–
–
–
–
Old Code
New Code
Reconfirm
Input screen for keycode
– – – –
System Lock
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu operation n Page 39
Taking the Keylock Off
Hold down ENTER on the projector for about
5 seconds.
Keylock Function
Use this function to lock the operation buttons
on the projector.
This function can be set using either the menu
screen or ENTER on the projector.
8
On-screen display
a
Setting with the menu screen
Selectable
items
Info
Description
• Even when Keylock function is set to “On”,
STANDBY/ON on the projector can be used
to turn on and off the power.
On
All buttons on the projector, except
STANDBY/ON, are locked.
• Keylock cannot be set while the projector is:
displaying the “Setup Guide” or “Menu”
screens, in Standby mode, warming up,
changing input signals, operating the Auto
Sync or Input Search function, in Freeze
mode or on the “System Lock” screen during
warming up.
Off
Turns off the Keylock function.
a
Setting with the projector buttons
Locking the Operation Buttons
Hold down ENTER on the
projector for about 5 seconds
while the projector is being
Selecting the Quick
Start Menu
turned on.
9
• The Keylock function screen is displayed.
PRJ - ADJ1
Use this function to lock the operation buttons
on the projector.
Selectable items
Description
(Except STANDBY/ON button)
On
Pressing MENU displays the
Quick Start Menu screen.
Note: You can release the keylock by holding
down ENTER on the projector for about 5 seconds.
Off
Pressing MENU displays the
Complete Menu screen.
Return
On
Setting the FUNCTION
Button Operation
You can assign one of the following functions
to the FUNCTION button on the remote con-
trol. The assigned function can be performed
by just pressing FUNCTION.
0
SEL.
ENTER
END
Select “On”, then press ENTER
.
On-screen display
Selectable items
Description
Input Search
Automatically searches for and
switches to the appropriate Input
mode.
• The Keylock function does not affect the
operation with the remote control buttons.
• You cannot use the Keylock function while the
projector is warming up.
Audio Mute
For temporarily turning off the
sound. Press FUNCTION again
to turn on the sound
Image Shift
Signal Info
For moving the projected image
vertically. (See page 46.)
Input signal information is
displayed.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projector Function (“PRJ-ADJ1/2” Menu)
(Continued)
Menu operation n Page 39
Checking the Lamp
Life Status
You can confirm the cumulative lamp usage
time and the remaining lamp life (percentage).
STANDBY Mode
When set to “Eco”, power consumption is
reduced in Standby mode.
Selectable
Description
items
Lamp usage condition
Remaining lamp life
Eco
The monitor output and RS-232C are
switched off in Standby mode.
“Life”
100%
Approx.
4,000 hours 200 hours
5%
Operated exclusively
with “Eco+Quiet”
set to “On”
Approx.
Quick Start The monitor output and RS-232C are
activated even if the projector is in
Standby mode.
Operated exclusively
with “Eco+Quiet”
set to “Off”
Approx.
2,000 hours 100 hours
Approx.
DLP® LinkTM (XR-55X only)
See the OPERATION MANUAL FOR
STEREOSCOPIC 3D PROJECTION provided
separately.
Note
• It is recommended that the lamp be changed
when the remaining lamp life becomes 5%.
• The lamp life may vary depending on the
usage condition.
DLP® LinkTM Invert
(XR-55X only)
See the OPERATION MANUAL FOR
STEREOSCOPIC 3D PROJECTION provided
separately.
Returning to the Default
Settings
This function allows you to initialize the
settings you have made in the projector.
Note
• The following items or menu cannot be
initialized.
- Resolution
- Language
- Lamp Timer (Life)
- System Lock
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Cleaning the projector
■ Ensure that you have unplugged the power
cord before cleaning the projector.
■ The cabinet as well as the operation panel is
made of plastic. Avoid using benzene or
thinner, as these can damage the finish on
the cabinet.
■ Do not use volatile agents such as
insecticides on the projector.
Cleaning the lens
■ Use a commercially available blower or lens
cleaning paper (for glasses and camera
lenses) for cleaning the lens. Do not use any
liquid type cleaning agents, as they may
wear off the coating film on the surface of the
lens.
■ As the surface of the lens can easily get
damaged, be careful not to scrape or hit the
lens.
Do not attach rubber or plastic items to the
projector for long periods.
The effects of some of the agents in the
plastic may cause damage to the quality or
finish of the projector.
■ Wipe off dirt gently with a soft flannel cloth.
Using a chemical cloth (wet/dry sheet type
cloth, etc.) may deform the components of
the cabinet or cause cracking.
■ Wiping with a hard cloth or using strong
force may scratch the cabinet surface.
■ When the dirt is hard to remove, soak a cloth
in a mild detergent diluted with water, wring
the cloth well and then wipe the projector.
Strong cleaning detergents may discolor,
warp or damage the coating on the projector.
Make sure to test on a small, inconspicuous
area on the projector before use.
Cleaning the exhaust and intake vents
■ Use a vacuum cleaner to clean dust from the
exhaust vent and the intake vent.
Mild detergent diluted
with water
Info
• If you want to clean the air vents during
projector operation, ensure you press
STANDBY/ON on the projector or
STANDBY on the remote control and put the
projector into Standby mode. After the
cooling fan has stopped, clean the vents.
Thinner
Wax
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance Indicators
■ The warning lights (power indicator, lamp indicator and temperature warning indicator) on the
projector indicate problems inside the projector.
■ If a problem occurs, either the temperature warning indicator or the lamp indicator will
illuminate red, and the projector will enter Standby mode. After the projector has entered
Standby mode, follow the procedures given below.
Temperature warning indicator
Lamp indicator
Top View
Power indicator
About the temperature warning indicator
If the temperature inside the projector increases, due to blockage of the air vents, or the setting
location, the temperature warning indicator will blink. And if the temperature keeps on rising,
“
” will illuminate in the lower left corner of the picture with the temperature warning
indicator blinking. If this state continues, the lamp will turn off, the cooling fan will run and then
the projector will enter Standby mode. When you find the temperature warning indicator
blinking, be sure to perform the measures described on page 55.
About the lamp indicator
■ When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will
be displayed on the screen. When the percentage becomes 0%, it will change to (red), the
lamp will automatically turn off and then the projector will automatically enter Standby mode.
At this time, the lamp indicator will illuminate in red.
■ If you try to turn on the projector a fourth time without replacing the lamp, the
projector will not turn on.
Indicators on the Projector
Power indicator
Red on
Normal (Standby)
Green on
Red blinks
Green blinks
Normal (Power on)
Abnormal (See page 55.)
Normal (Cooling)
Green and orange The lens shutter is closed. (See page 29.)
blink alternately
Lamp indicator
Green on
Green blinks
Red on
Normal
The lamp is warming up.
The lamp is shut down abnormally or requires to be
changed. (See page 55.)
Temperature
warning indicator
Off
Normal
Red on/Red blinks The internal temperature is abnormally high. (See page 55.)
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance indicator
Problem
Cause
Possible Solution
Normal
Abnormal
Temperature
warning
indicator
Off
Red blinks The internal
• Temperatures
around the projector
are high.
• Use the projector in an
area with a temperature of
lower than 95°F (+35ºC).
• Relocate the projector to
an area with proper
(On)/
temperature is
abnormally high.
Red on
(Standby)
• Blocked air intake
ventilation. (See page 8.)
• Cooling fan
breakdown
• Internal circuit failure
• Clogged air intake
• Take the projector to your
nearest Sharp Authorized
Projector Dealer or Service
Center (see page 69) for
repair.
Lamp
indicator
Green on
(Green
blinks
when the
lamp is
warming
up.)
Red on
Red on
The lamp does
not illuminate.
• The lamp is shut
down abnormally.
• Disconnect the power cord
from the AC outlet, and
then connect it again.
Time to change
the lamp.
• Remaining lamp life
becomes 5% or less.
• Carefully replace the lamp.
(See page 56.)
• Take the projector to your
nearest Sharp Authorized
Projector Dealer or Service
Center (see page 69) for
repair.
The lamp does
• Burnt-out lamp
• Lamp circuit failure
(Standby) not illuminate.
• Please exercise care when
replacing the lamp.
• Securely install the cover.
Power
indicator
Green on/ Red blinks The power
• The lamp unit cover • If the power indicator blinks
Red on
Green
blinks
indicator blinks in
red when the
projector is on.
is open.
in red even when the lamp
unit cover are securely
installed, contact your
nearest Sharp Authorized
Projector Dealer or Service
Center (see page 69) for
advice.
(Cooling)
Info
• If the temperature warning indicator illuminates, and the projector enters Standby mode, follow the
possible solutions above and then wait until the projector has cooled down completely before
plugging in the power cord and turning the power back on. (At least 10 minutes.)
• If the power is turned off for a brief moment due to power outage or some other cause while using
the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate
in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace
the power cord in the AC outlet and then turn the power on again.
• The cooling fan keeps the internal temperature of the projector constant and this function is
controlled automatically. The sound of the cooling fan may change during operation because the fan
speed may change and this is not a malfunction.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Regarding the Lamp
Lamp
■ It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes
5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life
(percentage) can be checked with the on-screen display. (See page 52.)
■ Purchase a replacement lamp of type AN-D350LP from your place of purchase, nearest Sharp
Authorized Projector Dealer or Service Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited
warranty. All service of this projector under warranty, including lamp replacement,
must be obtained through a Sharp Authorized Projector Dealer or Service Center.
For the name of the nearest Sharp Authorized Projector Dealer or Service Center,
please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
Hg LAMP CONTAINS MERCURY For State Lamp Disposal
Information
U.S.A ONLY
Caution Concerning the Lamp
■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure
can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches
or deterioration of the lamp due to a lapse of usage time.
The period of time up to failure largely varies depending on the individual lamp and/or the condition and
the frequency of use. It is important to note that failure can often result in the bulb cracking.
■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.
■ Should the lamp break, there is also a possibility that glass particles may spread inside of the projector.
In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or
Service Center to assure safe operation.
■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of
exposure to the gas, consult a doctor as soon as possible.
Replacing the Lamp
Caution
• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause
burns or injury.
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully
cool before removing the lamp unit.
■ Carefully change the lamp by following the instructions described in this section.
* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector
Dealer or Service Center.
*
If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector
Dealer or Service Center for repair.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing and Installing the
Lamp Unit
Warning!
• Do not remove the lamp unit from the
projector right after use. The lamp and parts
around the lamp will be very hot and may
cause burns or injury.
Optional
accessory
Lamp unit
AN-D350LP
Info
• Do not touch the glass surface of the lamp
unit or the inside of the projector.
• To avoid injury to yourself and damage to the
lamp, make sure you carefully follow the
steps below.
• Do not loosen other screws except for the
lamp unit cover and lamp unit.
Press STANDBY/ON on the
STANDBY/ON button
projector or STANDBY on the
remote control to put the
projector into Standby mode.
Disconnect the power cord.
2
• Unplug the power cord from the AC
socket.
• Leave the lamp until it has fully cooled
down (about 1 hour).
AC socket
Remove the lamp unit cover.
User service screw
(for lamp unit cover)
• Close the lens shutter and turn the
projector over. Loosen the user service
screw (1) that secures the lamp unit
cover. Remove the lamp unit cover (2).
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Regarding the Lamp (Continued)
Remove the lamp unit.
• Loosen the securing screw from the lamp
unit. Hold the lamp unit and pull it in the
Securing
screw
direction of the arrow. At this time, keep
the lamp unit horizontal and do not tilt it.
Insert the new lamp unit.
• Press the lamp unit firmly into the lamp unit
compartment. Fasten the securing screw.
Replace the lamp unit cover.
• Align the tab on the lamp unit cover
(1) and close it (2). Then tighten the user
service screw (3) to secure the lamp unit
cover.
Info
• If the lamp unit and lamp unit cover
are not correctly installed, the power
will not turn on, even if the power
cord is connected to the projector.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
• Make sure to reset the lamp timer only when
replacing the lamp. If you reset the lamp timer
and continue to use the same lamp, this may
cause the lamp to become damaged or
explode.
Connect the power cord and
open the lens shutter fully.
• Plug the power cord into the AC socket of
the projector.
AC socket
STANDBY/ON
button
Reset the lamp timer.
ENTER button
• While simultaneously holding down
MENU, ENTER and Ron the projector,
press STANDBY/ON on the projector and
keep all four buttons pressed down until
the lamp indicator starts blinking green.
• “LAMP 0000H” is displayed, indicating
that the lamp timer is reset.
MENU button
Rbutton
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Pin Assignments
COMPUTER/COMPONENT input and COMPUTER/COMPONENT output
Terminals: mini D-sub 15 pin female connector
15
COMPUTER Input/Output
COMPONENT Input/Output
11
Pin No.
1.
2.
3.
4.
Signal
Pin No.
1.
Signal
PR (CR)
Video input (red)
Video input (green/sync on green)
Video input (blue)
Not connected
2.
Y
3.
PB (CB)
4.
5.
6.
Not connected
Not connected
Earth (PR)
5.
Not connected
1
5
6.
Earth (red)
6
10
7.
8.
Earth (green/sync on green)
Earth (blue)
7.
8.
Earth (Y)
Earth (PB)
9.
Not connected
GND
Not connected
Bi-directional data
Horizontal sync signal: TTL level
Vertical sync signal: TTL level
Data clock
9.
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
10.
11.
12.
13.
14.
15.
10.
11.
12.
13.
14.
15.
RS-232C Terminal: mini DIN 9 pin female connector
8
Pin No.
Signal Name
I/O
Reference
1.
2.
3.
4.
5.
6.
7.
8.
9.
Not connected
9
7
RD
SD
Receive Data
Send Data
Input
Output
Connected to internal circuit
Connected to internal circuit
Not connected
Connected to internal circuit
Not connected
Connected to CS in internal circuit
Connected to RS in internal circuit
Not connected
SG
Signal Ground
6
3
RS
CS
Request to Send
Clear to Send
4
5
2
1
RS-232C Terminal: D-sub 9 pin male connector of the DIN-D-sub RS-232C adaptor
(optional, AN-A1RS)
1
5
Pin No.
Signal Name
I/O
Reference
1.
2.
3.
4.
5.
6.
7.
8.
9.
Not connected
RD
SD
Receive Data
Send Data
Input
Output
Connected to internal circuit
Connected to internal circuit
Not connected
Connected to internal circuit
Not connected
Connected to CS in internal circuit
Connected to RS in internal circuit
Not connected
SG
Signal Ground
6
9
RS
CS
Request to Send
Clear to Send
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Pin Assignments (Continued)
RS-232C Cable recommended connection: D-sub 9 pin female connector
5
1
Pin No.
Signal
CD
RD
SD
Pin No.
Signal
CD
RD
SD
1.
2.
3.
4.
5.
6.
7.
8.
9.
1.
2.
3.
4.
5.
6.
7.
8.
9.
ER
ER
SG
DR
RS
CS
CI
SG
DR
RS
CS
CI
9
6
Note
• Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on
the controlling device (e.g. computer).
Projector
Pin No.
Computer
Pin No.
4
5
6
4
5
6
USB Terminal: Type B USB connector
4 3
Pin No.
Signal Name
1.
2.
3.
4.
VCC
USB–
USB+
SG
USB power
USB data–
USB data+
Signal Ground
1 2
60
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Specifications and Commands
Computer control
A computer can be used to control the projector by connecting an RS-232C serial
control cable (cross type, commercially available) to the projector. (See page 24.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard.
Baud rate*: 9,600 bps / 38,400 bps / 115,200 bps
Data length: 8 bits
Parity bit: None
Stop bit: 1 bit
Flow control: None
*Set the projector's baud rate to the same rate as used by the computer.
Basic format
Commands from the computer are sent in the following order: command,
parameter, and return code. After the projector processes the command from the
computer, it sends a response code to the computer.
Command format
C1
C2
C3
C4
P1
P2
P3
P4
Return code (0DH)
Command 4-digit
Parameter 4-digit
Response code format
Normal response
Problem response (communication error or incorrect command)
O
K
E
R
R
Return code (0DH)
Return code (0DH)
Info
• When controlling the projector using RS-232C commands from a computer, wait for at least 30
seconds after the power has been turned on, and then transmit the commands.
• After sending an input selection or picture adjustment command and then receiving an “OK” response
code, the projector may take some time to process the command. If a second command is sent while
the projector is still processing the first command, you may receive an “ERR” response code. If this
happens, try resending the second command.
• When more than one code is being sent, send each command only after the response code for the
previous command from the projector is verified.
• “POWR????”, “TABN _ _ _ 1”, “TLPS _ _ _ 1”, “TPOW _ _ _ 1”, “TLPN _ _ _ 1”, “TLTT _ _ _ 1”,
“TLTM _ _ _ 1”, “TLTL _ _ _ 1”, “TNAM _ _ _ 1”, “MNRD _ _ _ 1”, “PJN0 _ _ _ 1”
− When the projector receives the special commands shown above:
* The on-screen display will not disappear.
* The “Auto Power Off” timer will not be reset.
− The special commands are available for applications that require continuous polling.
Note
• If an underbar (_) appears in the parameter column, enter a space.
• If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets
under Control Contents.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Specifications and Commands
(Continued)
Commands
Example: When turning on the projector, make the following setting.
Computer
Projector
→
←
P
O
W
R
_
_
_
1
O
K
RETURN
CONTROL CONTENTS
COMMAND
PARAMETER
Standby mode
Power ON
(or 30-second startup time)
_
_
_
_
_
_
Power
On
P
P
P
T
O
O
O
A
W
W
W
B
R
R
R
N
1
0
?
1
OK or ERR
OK
Off
OK
1
0: Normal
1: Temp High
8: Lamp Life 5% or less
16: Lamp Burn-out
OK or ERR
0
0: Normal
1: Temp High
2: Fan Error
4: Cover Open
Status
?
_
?
_
?
_
Projector Condition
32: Lamp Ignition Failure 8: Lamp Life 5% or less
16: Lamp Burn-out
32: Lamp Ignition Failure
64: Temp Abnormally High
_
_
_
Status
T
L
P
S
1
0: Off, 1: On, 2: Retry
3: Waiting, 4: Lamp Error
0: Off, 4: Lamp Error
Lamp
_
_
_
_
_
_
_
*
_
_
_
_
_
_
_
*
_
_
_
_
_
_
_
*
Power Status
Quantity
T
T
T
T
T
T
M
P
P
L
L
L
L
N
N
J
O
P
T
T
T
A
R
N
W
N
T
M
L
M
D
1
1
1
1
1
1
1
1
*
1: On, 2: Cooling
1
0: Standby
Usage Time(Hour)
0 – 9999(Integer)
0, 15, 30, 45
Usage Time(Minute)
Life(Percentage)
0% – 100%(Integer)
XR55X/XR50S
XR-55X/XR-50S
OK or ERR
Name
Model Name Check
Model Name Check
Projector Name Setting 1
(First 4 characters) *1
P
P
J
J
N
N
2
3
*
*
*
*
*
*
*
*
OK or ERR
OK or ERR
Projector Name Setting 2
(Middle 4 characters) *1
Projector Name Setting 3
(Last 4 characters) *1
_
_
_
_
_
_
_
_
_
_
_
_
Projector Name Check
COMPUTER
P
I
I
I
I
I
I
I
J
R
V
V
R
V
N
G
E
E
G
E
0
B
D
D
B
D
D
K
1
1
1
2
?
?
?
?
Projector Name
OK or ERR
Input Change
ERR
ERR
ERR
ERR
S-VIDEO
OK or ERR
VIDEO
OK or ERR
Input RGB Check
Input Video Check
Input Mode Check
Input Check
?
?
?
?
?
?
?
?
?
?
?
?
1: COMPUTER or ERR
1: S-VIDEO, 2: VIDEO or ERR ERR
M
C
O
H
1: RGB, 2: VIDEO
ERR
ERR
1: COMPUTER
2: S-VIDEO
3: VIDEO
_
_
_
*
*
Volume
Volume(0 – 60)
V
V
K
I
I
F
O
O
E
L
U
Y
B
B
E
E
J
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
R
A
D
S
K
K
Z
Z
S
R
R
R
R
R
R
R
V
V
V
V
V
V
V
V
V
V
E
*
*
*
*
*
*
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
Volume up/down(-10 – +10)
(
)
(
)
Keystone
AV Mute
-80 – +80 XGA /-40 – +40 SVGA
*
_
_
_
On
M
M
R
R
D
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
L
1
0
1
0
1
1
2
3
5
6
0
1
1
2
3
0
1
1
2
3
0
1
1
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
Off
On
Freeze
Off
Start
COMPUTER
F
Auto Sync
Resize
A
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
A
Normal
16:9
Native
Full
Border
Area Zoom
V-Stretch
Normal
16:9
1
1
_
_
_
S-VIDEO
VIDEO
Border
Area Zoom
V-Stretch
Normal
16:9
1
1
_
_
_
Border
Area Zoom
V-Stretch
1
1
_
All Reset
62
Download from Www.Somanuals.com. All Manuals Search And Download.
RETURN
CONTROL CONTENTS
COMMAND
PARAMETER
Standby mode
Power ON
OK or ERR
(or 30-second startup time)
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
COMPUTER Input
Picture Mode
Standard
Presentation
Movie
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
P
P
P
P
P
P
B
R
B
C
T
S
S
S
S
S
I
R
D
E
O
I
1
1
1
1
1
*
*
*
*
*
0
1
2
3
4
*
*
*
*
*
*
*
*
*
0
1
1
2
3
1
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
Game
sRGB
Contrast
Bright
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-1 – +1
*
*
*
*
*
*
Red
Blue
Color
Tint
*
*
*
_
Sharp
S
C
W
F
H
T
*
_
CLR Temp
BrilliantColor™
Film Mode
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
0 – +2
E
M
M
R
R
R
E
_
_
_
_
_
_
_
_
_
_
_
Auto
Off
F
DNR
Level 1
N
N
N
R
Level 2
Level 3
Picture Reset
Signal Type
ERR
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
Auto
I
I
I
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
S
S
S
A
A
P
P
P
P
P
B
R
B
C
T
I
I
I
I
I
0
1
2
1
2
0
1
2
3
*
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
RGB
YPbPr
Audio Input
AUDIO 1
AUDIO 2
Standard
Presentation
Movie
R
R
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
S-VIDEO Input
Picture Mode
S
S
S
S
I
R
D
E
O
I
H
T
E
M
M
R
R
R
1
1
1
1
*
Game
Contrast
Bright
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-1 – +1
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Red
Blue
Color
Tint
*
*
Sharp
S
C
W
F
*
*
*
_
CLR Temp
BrilliantColor™
Film Mode
*
*
_
_
_
_
_
_
_
_
_
_
_
_
0 – +2
Auto
Off
Level 1
Level 2
Level 3
*
0
1
1
2
3
F
DNR
N
N
N
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
Picture Reset
Audio Input
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
R
A
A
P
P
P
P
P
B
R
B
C
T
E
I
I
1
1
2
0
1
2
3
*
*
*
*
*
*
*
*
*
0
1
1
2
3
1
1
2
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
AUDIO 1
AUDIO 2
Standard
Presentation
Movie
VIDEO Input
Picture Mode
S
S
S
S
I
R
D
E
O
I
H
T
E
M
M
R
R
R
E
I
1
1
1
1
*
*
*
*
*
*
*
*
_
_
_
_
_
_
_
_
_
Game
Contrast
Bright
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-1 – +1
*
*
*
*
*
*
Red
Blue
Color
Tint
Sharp
S
C
W
F
*
_
CLR Temp
BrilliantColor™
Film Mode
_
_
_
_
_
_
_
_
_
0 – +2
Auto
Off
F
DNR
Level 1
N
N
N
R
A
A
Level 2
Level 3
Picture Reset
Audio Input
AUDIO 1
AUDIO 2
I
63
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Specifications and Commands
(Continued)
RETURN
CONTROL CONTENTS
COMMAND
PARAMETER
Standby mode
Power ON
OK or ERR
(or 30-second startup time)
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
C.M.S. Setting
C.M.S.
On
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
I
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
N
N
A
C
C
H
H
H
H
H
H
R
S
S
S
S
S
S
R
V
V
V
V
V
V
R
R
C
P
H
V
R
D
S
S
D
D
S
S
S
S
S
S
S
S
B
B
B
M
M
D
D
O
O
E
E
U
U
R
R
I
S
S
R
Y
G
C
B
M
E
R
Y
G
C
B
M
E
R
Y
G
C
B
M
E
E
L
1
0
*
*
*
*
*
*
_
1
0
*
*
*
*
*
*
2
*
*
*
*
*
*
3
*
*
*
*
*
*
4
1
*
*
*
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
Off
Hue
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
Red
*
*
*
*
*
Yellow
Green
Cyan
Blue
Magenta
Reset
Red
*
_
Saturation
*
*
*
*
*
*
*
*
*
*
Yellow
Green
Cyan
Blue
Magenta
Reset
Red
*
_
*
_
Value
*
*
*
*
*
*
_
_
*
*
*
*
*
*
_
_
Yellow
Green
Cyan
Blue
Magenta
Reset
C.M.S. All Reset
-150 – +150
-30 – +30
Clock
*
_
*
*
*
*
*
*
Phase
I
I
I
I
H
P
P
E
S
N
N
I
H-position
V-position
-150 – +150
-60 – +60
*
_
A
A
N
V
V
M
M
E
E
E
*
*
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
Fine Sync Adjustment Reset
Image Shift
1
*
(
)
(
)
-96 – +96 XGA /-75 – +75 SVGA
L
*
_
*
_
Overscan
On
O
O
I
1
0
1
0
1
2
3
4
5
6
7
8
1
3
4
1
0
1
0
1
0
1
0
1
0
1
0
1
0
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
Off
OSD Display
Video System
On
Off
I
I
Auto
PAL
M
M
M
M
M
M
M
M
I
Y
Y
Y
Y
Y
Y
Y
Y
G
G
G
D
D
J
SECAM
NTSC4.43
NTSC3.58
PAL-M
PAL-N
PAL-60
Logo
Blue
E
E
E
E
E
Background
M
M
M
H
H
A
A
P
P
R
I
I
None
On
Eco+Quiet
T
T
A
A
A
A
A
A
M
M
I
Off
Auto Sync
On
Off
J
Auto Power Off
Auto Restart
STANDBY Mode
PRJ Mode
On
W
W
S
S
T
Off
On
Off
R
Quick Start
Eco
Reverse
O
O
M
M
M
M
T
On
Off
On
Off
E
E
N
N
I
I
I
Invert
I
64
Download from Www.Somanuals.com. All Manuals Search And Download.
RETURN
CONTROL CONTENTS
COMMAND
PARAMETER
Standby mode
Power ON
OK or ERR
(or 30-second startup time)
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
Language
English
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
S
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
S
S
F
F
L
L
S
I
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
G
G
P
P
R
R
M
M
E
S
S
C
C
C
M
M
E
E
I
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
U
U
K
K
Q
Q
D
D
S
U
U
O
O
O
N
N
N
N
V
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
1
0
1
0
1
2
0
1
1
0
1
0
1
2
0
1
0
1
1
0
1
2
1
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
OK or ERR
Deutsch
Español
Nederlands
Français
Italiano
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
kHz(***.* or ERR)
Hz(***.* or ERR)
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
ERR
Svenska
Português
1
1
1
1
1
1
1
polski
Türkçe
Magyar
On
1
_
Setup Guide
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
Off
S
A
A
T
Internal Speaker
RGB Frequency Check
Fan Mode
On
Off
Horizontal
Vertical
Normal
High
T
H
H
I
V
V
W
W
W
Q
Q
3
Input Search *2
Video Setup
Start
0 IRE
7.5 IRE
Off
I
Wall Color
L
L
L
S
S
D
D
D
L
L
L
P
Blackboard
Whiteboard
On
Quick Start Menu
Off
DLP® LinkTM (XR-55X only)
Off
On
3
3
DLP® LinkTM Invert (XR-55X only)
Closed Caption
(For Americas only)
Off
C
C
C
L
C
C
C
R
A
A
A
E
CC1
CC2
Lamp Timer Reset *3
0
0
0
*1 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3.
*2 When the next command is sent during input search, you may receive an “ERR” response code, and the input
search is canceled.
*3 The Lamp Timer Reset command is available only in standby mode.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Compatibility Chart
Computer
•
Multiple signal support
Horizontal Frequency: 15-110 kHz,
Vertical Frequency: 45-85 Hz,
Pixel Clock: 12-165 MHz
Sync signal: Compatible with TTL level
Compatible with sync on green signal
•
Display
Horizontal frequency
[kHz]
Vertical
frequency[Hz]
PC/MAC
Mode
Resolution
640 × 400
720 × 400
XR-55X
XR-50S
27.0
31.5
37.9
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
31.3
35.2
37.9
46.6
48.1
46.9
53.7
40.3
48.4
56.5
60.0
68.7
45.0
47.8
49.7
62.8
47.7
47.8
55.9
55.0
66.2
67.5
60.0
75.0
64.0
80.0
64.0
65.3
65.3
75.0
34.9
49.7
60.2
60
70
85
60
70
85
50
60
70
72
75
85
50
56
60
70
72
75
85
50
60
70
75
85
60
60
60
75
60
60
60
60
70
75
60
75
60
75
60
60
60
60
67
75
75
VGA
Upscale
640 × 480
Upscale
SVGA
XGA
800 × 600
1024 × 768
TRUE
PC
TRUE
1280 × 720
1280 × 768
WXGA
1280 × 800
1360 × 768
1366 × 768
1440 × 900
Intelligent
Compression
WXGA+
1152 × 864
Intelligent
Compression
SXGA
1280 × 960
1280 × 1024
1400 × 1050
SXGA+
WSXGA+
UXGA
VGA
SVGA
XGA
1680 × 1050
1600 × 1200
640 × 480
832 × 624
1024 × 768
MAC 13”
MAC 16”
MAC 19”
Upscale
Upscale
TRUE
Intelligent
Intelligent
Compression
Compression
MAC 21”
SXGA
1152 × 870
68.7
75
Note
• Optimum image quality will be achieved by matching your computer's output resolution to the
resolution that corresponds to “TRUE” in the “Display” column shown above.
• When “Screen resolution” of the computer is different from the resolution displayed on the projected
image, follow the procedures shown below.
– Refer to “Resolution” on the “SIG-ADJ” menu and select the same resolution as the resolution in
“Screen resolution” of the computer.
–
Depending on the computer you are using, the output signal may not be faithful to the “Screen resolution”
adjustment. Check the settings of the computer's signal output. If the settings cannot be changed, it is
recommended that the resolution be set to the one that corresponds to “TRUE” in the “Display” column.
DTV
Horizontal
Vertical
Horizontal
Vertical
Signal
Signal
Frequency (kHz) Frequency (Hz)
Frequency (kHz) Frequency (Hz)
15.7
31.5
33.8
15.6
31.3
37.5
60
60
60
50
50
50
720P
1035I
1080I
1080I
1080P
1080P
45.0
33.8
28.1
33.8
56.3
67.5
60
60
50
60
50
60
480I
480P
540P
576I
576P
720P
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Check
Page
24
• Projector power cord is not plugged into the wall outlet.
• Power to the external connected devices is off.
• The lens shutter is closed.
–
25, 29
29
• The selected Input mode is wrong.
• The AV Mute function is working.
29
• Cables are incorrectly connected to the projector.
• Remote control battery has run out.
21–24
15
No picture and no sound
or projector does not
start.
•
External output has not been set when connecting a notebook computer. 21
• The lamp unit cover is not installed correctly.
• Cables are incorrectly connected to the projector.
• “Bright” is set to minimum position.
57, 58
21–24
42
• Depending on the computer you are using, an image may not be
projected unless the signal output setting of the computer is switched
to the external output. Refer to the computer's operation manual for
how to switch its signal output settings.
–
• Is “On” selected in “DLP® LinkTM”? (XR-55X only)
52
Sound is heard but no
picture appears
(or picture is dark).
48
42
• Check that “Wall Color” is configured correctly.
Dark or bluish image
• Image adjustments are incorrectly set.
• Make adjustments of “Color” and “Tint” in “Picture Mode” and lower the
“BrilliantColorTM” value.
(S-Video, Video Input only)
• Video input system is incorrectly set.
(COMPUTER/COMPONENT Input only)
• Input signal type (RGB/Component) is incorrectly set.
45
44
Color is faded or poor.
• Adjust the focus.
26
19
–
• The projection distance exceeds the focus range.
•
There is fog on the lens. If the projector is carried from a cold room into a
warm room, or if it is suddenly heated, condensation may form on the surface
of the lens and the image will become blurred. Set up the projector at least
one hour before it is to be used. If condensation should form, remove the
power cord from the wall outlet and wait for it to clear.
Picture is blurred;
noise appears.
(Computer Input only)
• Perform “SIG-ADJ” Adjustments (“Clock” and “Phase” Adjustment)
• Noise may appear depending on the computer.
44
–
• Cables are incorrectly connected to the projector.
21–24
29
• Volume is set to minimum.
• When the projector is connected to an external device and the volume
is set to minimum, the sound is not output even if you turn up the
volume of the external device.
• “Speaker” is set to “Off”.
• The Audio Mute function is working.
49
51
Picture appears but no
sound is heard.
• Make the necessary adjustments of each item in the “SIG-ADJ” menu. 44
Data image is not
centered.
• Depending on the computer you are using, the output resolution signal
may be different from the one you have set. For details, refer to the
operation manual of the computer.
–
• If the picture is normal, the sound is due to cabinet shrinkage caused
by room temperature changes. This will not affect operation or
performance.
–
An unusual sound is
occasionally heard from
the cabinet.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting (Continued)
Problem
Check
Page
54
• See “Maintenance Indicators”.
Maintenance indicator on
the projector illuminates
or blinks in red.
• Change the input signal type setting.
• Image adjustments are incorrectly set.
44
Picture is green on
COMPUTER (Component)
Picture is pink
(no green) on
COMPUTER (RGB)
42
Picture is too bright and
whitish.
• When temperature inside the projector increases, the cooling fan runs 8, 9
The cooling fan becomes
noisy.
faster.
53, 54, 55
• The lamp indicator is illuminating in red.
Replace the lamp.
54, 57, 58
The lamp does not light
up even after the
projector turns on.
• The lens shutter is closed.
25, 29
21–24
The lamp suddenly turns
off during projection.
• Cables are incorrectly connected to the projector or the connected
equipment works improperly.
• If this happens frequently, replace the lamp.
The image sometimes
fl ic k e r s .
57
57
• The lamp will eventually need to be changed.
While the remaining lamp life draws to a close, replace the lamp.
The lamp needs much
time to turn on.
Picture is dark.
• Operate the remote control while pointing it at the projector's remote
control sensor.
• The remote control may be too far away from the projector.
• If direct sunlight or a strong fluorescent lamp is shining on the
projector's remote control sensor, place the projector where it will not
be affected by strong light.
15
The remote control
cannot be used.
• The batteries may be depleted or inserted incorrectly. Make sure the
batteries are inserted correctly or insert new ones.
15
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect
operation or interference. If this should happen, unplug the Unit and plug it in again after more than 5
minutes.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
For SHARP Assistance
If you encounter any problems during setup or operation of this projector, first
refer to the “Troubleshooting” section on pages 67 and 68. If this operation
manual does not answer your question, please contact the SHARP Service
departments listed below.
U.S.A.
Sharp Electronics Corporation
1-888-GO-SHARP (1-888-467-4277)
Benelux
SHARP Electronics Benelux BV
0900-SHARPCE (0900-7427723)
Nederland
9900-0159 Belgium
Canada
Mexico
Sharp Electronics of Canada Ltd.
(905) 568-7140
Australia
Sharp Corporation of Australia Pty.
Ltd.
1300-135-022
Sharp Electronics Corporation
Mexico Branch
(525) 716-9000
New Zealand Sharp Corporation of New Zealand
Phone: (09) 573-0111
Latin America Sharp Electronics Corp. Latin
American Group
Fax: (09) 573-0112
(305) 264-2277
Singapore
Hong Kong
Taiwan
Sharp-Roxy Sales (S) Pte. Ltd.
65-226-6556
Germany
U.K.
Sharp Electronics (Europe) GMBH
01805-234675
Sharp-Roxy (HK) Ltd.
(852) 2410-2623
Sharp Electronics (U.K.) Ltd.
08705 274277
Italy
Sharp Electronics (Italy) S.P.A.
(39) 02-89595-1
Sharp Corporation (Taiwan)
0800-025111
France
Sharp Electronics France
01 49 90 35 40
Malaysia
U.A.E.
Sharp-Roxy Sales & Service Co.
(60) 3-5125678
Sharp Middle East Fze
971-4-81-5311
Spain
Sharp Electronica Espana, S.A.
93 5819700
Thailand
Korea
Sharp Thebnakorn Co. Ltd.
02-236-0170
Switzerland
Sweden
Austria
Sharp Electronics (Schweiz) AG
0041 1 846 63 11
Sharp Electronics Incorporated of
Korea
(82) 2-3660-2002
Sharp Electronics ( Nordic ) AB
(46) 8 6343600
India
Sharp Business Systems (India)
Limited
(91) 11- 6431313
Sharp Electronics (Europe) GMBH
Branch Office Austria
0043 1 727 19 123
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Model
Display devices
Resolution
XR-55X
XR-50S
0.55" DLP® Chip ×1
XGA (1024 × 768)
F 2.4 – 2.6
SVGA (800 × 600)
Lens
F number
Zoom
Manual, ×1.20 (f = 19.0 – 22.7 mm)
Focus
Manual
×1
Input terminals Computer/Component
(mini D-sub 15 pin)
S-Video (mini DIN 4 pin)
Video (RCA)
×1
×1
Audio (ø3.5 mm stereo minijack)
×1
Audio (RCA)
Output terminal Computer/Component
(mini D-sub 15 pin)
×1 (L/R)
×1
Control and
communication
terminals
USB (Type B)
×1
×1
RS-232C (mini DIN 9 pin)
Speaker
7W (Mono)
210 W
AC 100 – 240 V
50/60 Hz
2.8 A
Projection lamp
Rated voltage
Rated frequency
Input current
Power consumption
Eco+Quiet AC 100 V
Off
274 W
265 W
AC 240 V
Eco+Quiet AC 100 V
On
215 W
210 W
AC 240 V
Power consumption
(STANDBY Mode)
Quick Start AC 100 V
AC 240 V
3.0 W
3.7 W
2.6 W
3.2 W
Eco
AC 100 V
AC 240 V
0.32 W
0.77 W
Operation temperature
Cabinet
Dimensions (main body only) [W × H × D]
41ºF to 95ºF (+5ºC to +35ºC)
Plastic
11 52/64" × 3 1/8" × 9 19/64"
(300 × 79 × 236 mm)
Weight (approx.)
6.2 lbs. (2.8 kg)
As a part of policy of continuous improvement, SHARP reserves the right to make design and
specification changes for product improvement without prior notice. The performance specification
figures indicated are nominal values of production units. There may be some deviations from these
values in individual units.
This SHARP projector uses a DLP® chip. This very sophisticated panel contains 786,432 (XR-
55X)/480,000 (XR-50S) pixels (micromirrors). As with any high technology electronic equip-
ment such as large screen TVs, video systems and video cameras, there are certain accept-
able tolerances that the equipment must conform to.
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots
on the picture screen. This will not affect the picture quality or the life expectancy of the unit.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Units: inches (mm)
2 61/64 (75)
11 52/64 (300)
1 31/32 (50)
M4 M4
M4 M4
1 9/32 (32.5)
2 61/64 (75)
5 27/64 (137.5)
4 21/32 (118)
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
16:9······································································30, 31
3D MODE button·······················································14
MAGNIFY buttons ·····················································33
MENU button·····························································38
MONITOR OUT terminal············································23
MOUSE/Adjustment buttons·······························34, 38
Accessories·······························································11
AC socket··································································24
Adjustment buttons·············································38, 39
Adjustment foot·························································27
All Reset ····································································52
AREA ZOOM ·····························································31
Aspect ratio ·······························································30
Audio input ································································29
AUDIO 1, 2 terminals·················································23
Audio Mute································································51
Auto Power Off··························································49
Auto Restart ······························································49
Auto Sync (Auto Sync adjustment) ·····················33, 49
AUTO SYNC button···················································33
AV MUTE button························································29
NATIVE·······································································30
NORMAL ·····························································30, 31
ON button··································································25
Optional accessories·················································11
OSD Display ·····························································47
Overscan ···································································47
PAGE DOWN button··················································34
PAGE UP button························································34
PDF············································································10
Phase·········································································44
Picture Adjustment ···················································41
Picture Mode·······················································33, 41
PICTURE MODE button ············································33
POINTER button························································32
Power cord································································24
Power indicator ·························································54
PRJ-ADJ1/2·······························································49
PRJ Mode····························································20, 48
Background·······························································48
Batteries ····································································15
Blue ···········································································48
BORDER······························································30, 31
BREAK TIMER button ···············································32
Bright·········································································42
BrilliantColorTM ··························································42
Quick Start Menu ······················································39
R-CLICK/RETURN button···································34, 38
Red············································································42
Remote control··························································14
Remote control sensor··············································15
Replacing the lamp··············································56, 57
Resize··································································30, 46
RESIZE button···························································30
Resolution ·································································44
RGB cable ·································································21
RS-232C terminal······················································24
Clock ·········································································44
Closed Caption··························································47
CLR Temp (Color Temperature)·································42
C.M.S. ·······································································42
Color··········································································42
Complete Menu·························································39
COMPUTER/COMPONENT input terminal ·········21, 22
Contrast·····································································42
DIN-D-sub RS-232C adaptor····································11
DLP® LinkTM ·······························································52
DLP® LinkTM Invert ·····················································52
DNR···········································································43
SCR-ADJ···································································46
Screen Size and Projection Distance ························19
Security bar ·······························································13
Setup Guide ························································26, 48
Sharp·········································································42
SIG-ADJ ····································································44
Signal Info··································································45
Signal Type································································44
Speaker ·····································································49
SPOT button······························································32
STANDBY button·······················································25
STANDBY Mode························································52
STANDBY/ON button ················································25
Supplied accessories ················································11
S-VIDEO terminal ······················································22
System Lock······························································50
Eco+Quiet····························································32, 43
ECO+QUIET button···················································32
ENTER button····························································38
Exhaust vent························································12, 53
Fan Mode ··································································50
Film Mode··································································43
Focus ring··································································26
FREEZE button··························································33
FULL··········································································30
FUNCTION button·····················································14
FUNCTION Button setting·········································51
HEIGHT ADJUST lever··············································27
H-Pos ········································································44
Temperature warning indicator··································54
Tint·············································································42
Image shift·································································46
Information ································································39
INPUT modes····························································29
Input Search Start ·····················································39
Intake vent···························································12, 53
USB terminal ·····························································34
Video Setup·······························································45
Video System ····························································45
VIDEO terminal··························································22
VOL (Volume) buttons················································29
V-Pos·········································································44
V-STRETCH·······························································31
Kensington Security Standard connector ·················13
Keycode ···································································50
Keylock ·····································································51
KEYSTONE button ···················································28
Keystone Correction············································28, 46
Wall Color··································································48
Zoom ring··································································27
Lamp ·········································································56
Lamp indicator ··························································54
Lamp Timer (Life)·······················································52
Lamp unit ··································································57
Language (on-screen display language) ···················48
L-CLICK/EFFECT button·····································32, 34
Lens shutter·························································25, 29
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|