Sharp Projector PGD210U User Manual

PG-D210U

LCD PROJECTOR

PROJECTEUR LCD

PROYECTOR LCD

OPERATION MANUAL

MODE D’EMPLOI

MANUAL DE OPERACION

Contents

• Important Information ................................................................... 1

• Important Safeguards ................................................................... 2

• Cautions Concerning the Laser Pointer ........................................ 3

• Notes on Operation ...................................................................... 4

• Outstanding Features ................................................................... 4

• Location of Controls ..................................................................... 5

• Operating the Wireless Mouse Remote Control .......................... 6

• Wireless Mouse Functions ........................................................... 8

• Setting Up the Projector ............................................................... 9

• Using the Image Invert/Reverse Function .................................. 11

• Connecting the Projector (VIDEO 1, VIDEO 2) ......................... 14

• Connecting the Projector (RGB 1, 2: Computer) ....................... 15

• Input Signals (Recommended Timing) ....................................... 18

• RGB Adjustment Controls .......................................................... 19

• Basic Operation of the Projector ................................................ 21

• Adjusting the Picture .................................................................. 24

• Adjusting the Audio .................................................................... 25

• Functions on the Projector ......................................................... 26

• Air Filter Maintenance ................................................................ 29

• Lamp/Maintenance Indicators .................................................... 30

• Before Calling for Service ........................................................... 30

• Lamp Replacement .................................................................... 31

• Connection Pin Assignments ..................................................... 33

• RS-232C Terminal Specifications ............................................... 34

• Wired Remote Control Terminal Specifications ......................... 36

• Specifications ............................................................................. 37

• Dimensions ................................................................................ 38

ENGLISH

FRANÇAIS

ESPAÑOL

Table des matières

• Informations importantes.............................................................. 1

• Mises en garde importantes ......................................................... 2

• Précautions touchant le pointeur laser ......................................... 3

• Remarques sur le fonctionnement................................................ 4

• Caractéristiques spéciales ........................................................... 4

• Emplacement des commandes .................................................... 5

• Utilisation de la télécommande/souris sans fil ..............................6

• Fonctions de la souris sans fil ...................................................... 8

• Installation du projecteur .............................................................. 9

• Utilisation de la fonction d’inversement/renversement ............... 11

• Branchement du projecteur (VIDEO 1, VIDEO 2) ...................... 14

• Branchement du projecteur (RVB 1, 2: Ordinateur) ................... 15

• Signaux d’entrée (synchronisation recommandée) ................... 18

• Commandes de réglage RVB ..................................................... 19

• Fonctionnement de base du projecteur ...................................... 21

• Réglage de l’image .................................................................... 24

• Réglage du son .......................................................................... 25

• Fonctions du projecteur .............................................................. 26

• Entretien du filtre à air ................................................................ 29

• Lampe/Témoins d’entretien ........................................................ 30

• Avant d’appeler un réparateur .................................................... 30

• Changement de l’unité de lampe (lampe/boîtier)....................... 31

• Fonctions des broches du connecteur........................................ 33

• Fiche technique de la prise RS-232C ......................................... 34

• Fiche technique de la prise de la télécommande à fil ................ 36

• Fiche technique .......................................................................... 37

• Dimensions ................................................................................ 38

Indice

• Información importante ................................................................ 1

• Medidas de seguridad importantes .............................................. 2

• Precauciones respecto al puntero láser ....................................... 3

• Notas acerca de la operación....................................................... 4

• Características más sobresalientes ............................................. 4

• Ubicación de los controles ........................................................... 5

• Utilización del control remoto inalámbrico tipo ratón ................... 6

• Funciones del ratón inalámbrico .................................................. 8

• Instalación del proyector .............................................................. 9

• Utilización de la función de imagen invertida/de espejo ............ 11

• Conexión del proyector (VÍDEO 1, VÍDEO 2) ............................. 14

• Conexión del proyector (RGB 1, 2: Ordenador) ........................ 15

• Señales de entrada (tiempos recomendados) ............................18

• Controles de ajuste de RGB....................................................... 19

• Funcionamiento básico del proyector ......................................... 21

• Ajuste de la imagen.................................................................... 24

• Ajuste del sonido ........................................................................ 25

• Funciones del proyector ............................................................. 26

• Mantenimiento del filtro de aire .................................................. 29

• Lámpara/indicadores de mantenimiento .................................... 30

• Antes de solicitar el servicio de reparación ................................ 30

• Reemplazo de la lámpara .......................................................... 31

• Asignaciones de las conexiones de clavijas ...............................33

• Especificaciones del terminal RS-232C ..................................... 34

•

Especificaciones del terminal del control remoto con cable .......... 36

• Especificaciones ........................................................................ 37

• Diagramas acotados .................................................................. 38

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not

expressly approved by the manufacturer could void the user’s authority to operate this equipment.

U.S.A. ONLY

INFORMATION

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause

harmful interference, in which case the user will be required to correct the interference at his own expense.

U.S.A. ONLY

The enclosed RGB signal cable and Macintosh adaptor must be used with the device. The cable and adaptor

are provided to ensure that the device complies with FCC Class A verification.

U.S.A. ONLY

Important Safeguards

Electrical energy can perform many useful functions. This unit has been engineered and manufactured to ensure

your personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD.

In order not to defeat the safeguards incorporated into this LCD Projector, observe the following basic rules for its

installation, use and servicing. For your own protection and reliable usage of your LCD Projector, please be sure to

read these “Important Safeguards” carefully before use.

1. Read Instructions—All the safety and operating instructions should be read before the product is operated.

2. Retain Instructions—The safety and operating instructions should be retained for future reference.

3. Heed Warnings—All warnings on the product and in the operating instructions should be adhered to.

4. Follow Instructions—All operating and use instructions should be followed.

5. Cleaning—Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol

cleaners. Use a damp cloth for cleaning.

6. Attachments—Do not use attachments not recommended by the product manufacturer as they may cause

hazards.

7. Water and Moisture—Do not use this product near water – for example, near a bathtub, wash bowl, kitchen

sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

8. Accessories—Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product

may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart,

stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of

the product should follow the manufacturer’s instructions, and should use a mounting accessory recom-

mended by the manufacturer.

9. A product and cart combination should be moved with care. Quick stops, excessive force,

and uneven surfaces may cause the product and cart combination to overturn.

10. Ventilation—Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the

product and to protect it from overheating, and these openings must not be blocked or covered. The open-

ings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This prod-

uct should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is

provided or the manufacturer’s instructions have been adhered to.

11. Power Sources—This product should be operated only from the type of power source indicated on the

marking label. If you are not sure of the type of power supply to your home, consult your product dealer or

local power company. For products intended to operate from battery power, or other sources, refer to the

operating instructions.

12. Grounding or Polarization—This product is equipped with a three-wire grounding-type plug, a plug having a

third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you

are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the grounding-type plug.

13. Power-Cord Protection—Power-supply cords should be routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience

receptacles, and the point where they exit from the product.

E-2

Download from Www.Somanuals.com. All Manuals Search And Download.

14. Lightning—For added protection for this product during a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will pre-

vent damage to the product due to lightning and power-line surges.

15. Overloading—Do not overload wall outlets, extension cords, or integral convenience receptacles as this can

result in a risk of fire or electric shock.

16. Object and Liquid Entry—Never push objects of any kind into this product through openings as they may

touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill

liquid of any kind on the product.

17. Servicing—Do not attempt to service this product yourself as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

18. Damage Requiring Service—Unplug this product from the wall outlet and refer servicing to qualified service

personnel under the following conditions:

a. When the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into the product.

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following the operating instructions. Adjust only those con-

trols that are covered by the operating instructions, as an improper adjustment of other controls may

result in damage and will often require extensive work by a qualified technician to restore the product to

normal operation.

e. If the product has been dropped or damaged in any way.

f. When the product exhibits a distinct change in performance—this indicates a need for service.

19. Replacement Parts—When replacement parts are required, be sure the service technician has used replace-

ment parts specified by the manufacturer or with the same characteristics as the original part. Unauthorized

substitutions may result in fire, electric shock, or other hazards.

20. Safety Check—Upon completion of any service or repairs to this product, ask the service technician to per-

form safety checks to determine that the product is in proper operating condition.

21. Wall or Ceiling Mounting—The product should be mounted to a wall or ceiling only as recommended by the

manufacturer.

22. Heat—The product should be situated away from heat sources such as radiators, heat registers, stoves, or

other products (including amplifiers) that produce heat.

Cautions Concerning the Laser Pointer

The laser pointer on the remote control

emits a laser beam from the laser light

window shown in the figure to the left. The

"COMPLIES WITH 21 CFR SUBCHAPTER J"

SHARP ELECTRONICS CORPORATION

SHARP PLAZA, MAHWAH, NEW JERSEY 07430

CAUTION

U.S.A. ONLY

TEL : 1-800-BE-SHARP

LASER RADIATION-

REMOTE CONTROL

MODEL NO. : G1414CESA

DC6V (1.5VX4PCS.)

MADE IN JAPAN

DO NOT STARE INTO BEAM

laser emitted is a class II laser; therefore,

do not look into the laser window or shine

the laser beam on yourself or other people.

The three marks to the left are the caution

labels for the laser beam.

Always use the laser pointer at tempera-

tures between 41°F and 104°F (

5°C and

40°C).

WAVE LENGTH : 670nm

MAX. OUTPUT : 1mW

CLASS II LASER PRODUCT FABRIQUÉ AU JAPON

AVOID EXPOSURE—

LASER RADIATION IS

EMITTED FROM THIS

APERTURE.

Caution:

• Use of controls or adjustments or perfor-

mance of procedures other than those speci-

fied herein may result in hazardous radiation

exposure.

LASER LIGHT WINDOW

E-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes on Operation

About the Temperature Monitor Function:

• If the projector starts to overheat due to set-up problems or a dirty air filter, “TEMP.” will flash

in the upper-left corner of the picture. If the temperature continues to rise, then the lamp will

turn off, the TEMPERATURE WARNING indicator will flash, and after a 90-second cooling-off

period the power will shut off. Refer to page 30, “Maintenance Indicators,” when the “TEMP.”

warning appears in the picture.

TEMP.

• The cooling fan regulates the internal temperature, and its performance is automatically

controlled. The sound of the fan may change during operation due to changes in the fan

speed.

Outstanding Features

Allows easy projection of large screen, full-color com-

puter and video images.

• Can be projected directly onto a video screen or white

wall.

• Lightweight, convergence-free system for easy installa-

tion.

DIRECT COMPUTER COMPATIBILITY

A multi-scan RGB Input accepts signals from SXGA

(1,280 dots

1,024 lines compressed), XGA (1,024 dots

768 lines), SVGA (800 dots

600 lines), VGA

(640 dots

480 lines) and Mac (1,024 dots

768 lines

maximum) compatible computers without the need for

any additional hardware.

HIGH PICTURE QUALITY

The three LCD panels contain 786,432

RGB pixels to

achieve exceptionally bright, high quality images.

INTELLIGENT COMPRESSION

SXGA images are compressed and projected without

image data loss.

VERSATILE REMOTE CONTROL

• Built-in wireless mouse allows simultaneous operation

of projector and computer.

• Built-in Laser Pointer for professional presentations.

FLEXIBLE USE

• In addition to the standard front projection mode, the

menu driven functions can be used to instantly reverse

the image for rear projection, and invert the image for

ceiling mounting.

• Screen projection size adjusts from 40 to 300 inches.

BUILT-IN STEREO SPEAKERS

Built in 2 W

2 W stereo amplifiers and speakers elimi-

nate the need for external audio components.

USE WITH “PLUG AND PLAY”

“Plug and Play” compatible with VESA DDC 1 and

DDC 2B standards.

E-4

Download from Www.Somanuals.com. All Manuals Search And Download.

Location of Controls

FRONT VIEW

Speakers

Cautions:

• The exhaust vent, the lamp cage cover and adjacent areas may be

extremely hot during projector operation. To prevent injury, do not

touch these areas until they have sufficiently cooled.

• Allow at least 4؆ (10 cm) of space between the cooling fan (exhaust

vent) and the other nearest wall or obstruction.

Zoom ring

• If the cooling fan becomes obstructed, a protection device will

automatically turn off the projector lamp. This does not indicate a

malfunction. Remove the projector plug from the wall outlet and wait

10 minutes. Then turn on the power by plugging the cord back in.

This will return the projector to its normal mode.

Remote sensor

Lens focusing ring

Cooling fan (Intake vent)

OPERATION PANEL ON TOP OF PROJECTOR

LAMP REPLACEMENT indicator

TEMPERATURE WARNING indicator

POWER indicator

POWER

ON/OFF

LAMP

TEMP.

MUTE button

MUTE

POWER ON/OFF button

VOL

VOLUME UP-

DOWN buttons

INPUT SELECT

BLACK

SCREEN

INPUT SELECT button

BLACK SCREEN button

MENU button

ADJUSTMENT

(ß/©, ƒ/∂) buttons

ENTER

ENTER button

SIDE AND REAR VIEW

Cooling fan

Carrying handle

(Exhaust vent)

COMPUTER RGB INPUT 2 connector (HD-15)

COMPUTER RGB

INPUT 1 connector

(HD-15)

COMPUTER AUDIO INPUT 1

(3.5 mm Stereo Minijack)

COMPUTER RGB

COMPUTER AUDIO

IN 2

IN 1

IN 2

COMPUTER AUDIO INPUT 2

(3.5 mm Stereo Minijack)

Security Lock Anchor

COMPUTER RGB

OUTPUT

connector (HD-15)

AUDIO

WIRED

REMOTE

OUT

This projector has a Kensington

Security Standard connector for use

with a Kensington MicroSaver

Security System. Refer to the

information that came with the

system for instructions on how to use

it to secure this model.

OUTPUT

WIRED REMOTE

CONTROL INPUT

(3.5 mm Minijack)

PC CONTROL

VIDEO INPUT 1

COMPOSITE

Video: RCA

AUDIO OUTPUT

(3.5 mm Stereo Minijack)

(VIDEO/COMPUTER RGB)

OFF

Audio: RCA

Note:

MAIN POWER

switch

VIDEO INPUT 2

S-Video: 4-pin mini DIN

Audio: RCA

S-VIDEO

VIDEO

• Be sure to use the Computer

Control cable when connecting

the PC CONTROL terminals.

AUDIO

110-120V/

200-240V~

AC INLET

• PC CONTROL 1:

Use the supplied computer control cable when operating the remote

control as a wireless mouse or when controlling the projector from

the RS-232C terminal.

• PC CONTROL 2:

Use the computer control cable (CTANZ0711CE01) (sold separately)

when operating the remote control as a wireless mouse.

Notes:

• RS-232C does not function when connected to PC CONTROL 2.

• See page 15 for connection.

E-5

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating the Wireless Mouse Remote Control

The functions of your personal computer’s mouse have been built into the remote control enabling you to operate

your projector and personal computer with the remote control.

1. Slide the MAIN POWER switch on the rear of the projector on.

2. Press the POWER ON button on the front panel of the remote control to turn the projector power on.

3. When using the remote control as a wireless mouse, move the MOUSE/ADJUSTMENT switch to the MOUSE

position. When using the remote control to operate the projector, move the MOUSE/ADJUSTMENT switch to

the ADJ. position. To activate the remote control key back-light feature, press the LIGHT button on the remote

control. The colors of the buttons will change as shown in the table at the bottom of this page.

Wireless Mouse Remote Control

FRONT VIEW

SIDE VIEW

TRANSMIT indicator

MUTE button

MAIN POWER switch

of remote control

VOL

Note:

MUTE

• When transporting

the remote control,

turn off the MAIN

POWER switch to

avoid draining the

batteries.

OFF

POWER ON/OFF

buttons

VOLUME UP-DOWN

buttons

BLACK

SCREEN

LASER/

LASER POINTER/MENU

button

BLACK SCREEN

button

LEFT-CLICK button

MOUSE/ADJUSTMENT

(ß/©), (ƒ/∂) buttons

RIGHT-CLICK/ENTER

button

R-CLICK/ENTER

INPUT SELECT

DATA1

DATA2

INPUT SELECT

buttons

Remote control handling precautions

• The laser beam used in this product is harmless when

directed onto the skin, however please be careful not to

project the beam directly into the eyes. Do not stare into

the beam using an optical instrument.

VIDEO1

CHECK

VIDEO2

INPUT CHECK button

• Do not expose the remote control to shocks, liquids or

high humidity.

The remote control may not operate normally if exposed

to direct sunlight or other intense light sources. Should

this happen, reposition the light source or the projector.

MOUSE label

ADJ. label

MOUSE

ADJ.

MOUSE/ADJUSTMENT

switch

LIGHT

LIGHT button

LCD PROJECTOR

When you change the setting of the MOUSE/ADJUSTMENT switch,

the functions of certain buttons on the remote control change. You

can tell which function the button currently possesses by the color

of its back-light display.

Using the remote control in a dark

Button name

Position of MOUSE/ADJUSTMENT switch

room

MOUSE

LASER POINTER/MENU LASER POINTER (GREEN)

ADJ.

• Press the LIGHT button to turn on the back-

lights for the operation buttons for about 5 sec-

onds. The back-light colors are described in the

table to the right.

MENU (RED)

ENTER (RED)

ADJ. ß/©, ƒ/∂ (NOT LIT)

—

RIGHT-CLICK/ENTER

MOUSE/ADJUSTMENT

LEFT-CLICK

RIGHT-CLICK (GREEN)

MOUSE (NOT LIT)

ON (NOT LIT)

Note:

BLACK SCREEN

POWER ON/OFF

VOLUME UP-DOWN

MUTE

BLACK SCREEN (RED)

• If the MAIN POWER switch on the remote con-

trol is left on for more than 10 minutes without

operation, the power will automatically turn off.

To turn the power back on, press any button on

the remote control for at least one second.

DATA 1

ON (RED)

DATA 2

VIDEO 1

VIDEO 2

INPUT CHECK

E-6

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the optional cable with the remote control

When the remote control cannot be used due to the

range or positioning of the projector (rear projection,

etc.), connect the optional cable from the Wired Remote

Control Input jack on the remote control to the Wired

Remote Input on the rear of the projector.

TOP VIEW

REMOTE CONTROL SIGNAL

TRANSMITTER

WIRED REMOTE CONTROL

INPUT (3.5 mm Minijack)

Note:

• The signal transmitter does not function when the optional

cable is connected to the remote control.

LASER LIGHT WINDOW

Laser light shines out of this window.

The laser pointer on the remote control

emits a laser beam from the laser light win-

dow shown in the figure to the left. The laser

emitted is a class II laser; therefore, do not

look into the laser window or shine the laser

beam on yourself or other people. The two

marks to the left are the caution labels for

the laser beam.

"COMPLIES WITH 21 CFR SUBCHAPTER J"

SHARP ELECTRONICS CORPORATION

SHARP PLAZA, MAHWAH, NEW JERSEY 07430

CAUTION

U.S.A. ONLY

TEL : 1-800-BE-SHARP

LASER RADIATION-

REMOTE CONTROL

MODEL NO. : G1414CESA

DC6V (1.5VX4PCS.)

MADE IN JAPAN

DO NOT STARE INTO BEAM

WAVE LENGTH : 670nm

MAX. OUTPUT : 1mW

CLASS II LASER PRODUCT FABRIQUÉ AU JAPON

Always use the laser pointer at tempera-

tures between 41°F and 104°F (

5°C and

40°C).

REAR VIEW

Inserting the batteries

Remove the battery cover as shown and insert four AA

size batteries making sure their polarities match the (

)

and (

) marks inside the battery compartment.

Press in and

downward on

the arrow

mark and

remove.

Notes:

Incorrect use of batteries may cause them to leak or burst.

• Insert the batteries with the (

) and (

) polarities as indi-

cated.

• Remove the batteries if the remote control will not be oper-

ated for an extended period of time.

• Maintain the batteries in a clean condition.

• Do not mix different brands of batteries. The life expectancy

of the new batteries will be shortened and the old batteries

may leak.

Insert the side

tabs into their

slots and

press in the

cover until

properly

seated.

• When the batteries have been used up, remove them imme-

diately to prevent leakage and damage. Leaked battery fluid

may irritate the skin. Remove any battery fluid by wiping with

a cloth.

• Due to storage conditions and the shelf life of the supplied

batteries, they may run out after a short time. If so, replace

them with new batteries as soon as possible.

Remote control positioning

Use the remote control as shown in the figures on the left.

Transmission range

Reception range

Note:

30°

• The signal from the remote control can be reflected off the

screen for easy operation. However, the effective distance of

the signal may differ due to the screen material.

Max. distance: 23

(7 m)

45°

30°

E-7

Download from Www.Somanuals.com. All Manuals Search And Download.

Wireless Mouse Functions

The wireless mouse functions and laser pointer on the

remote control can help you create a more professional

presentation.

Connection Example

Rear terminals

COMPUTER RGB

COMPUTER AUDIO

IN IN

AUDIO

OUTPUT

WIRED

REMOTE

OUT

• By connecting the supplied computer control cable to the

PC CONTROL terminal on your projector and the supplied

mouse control cables to the mouse terminal on your

personal computer, you can use the wireless mouse on the

remote control, instead of the mouse equipped with your

personal computer, to operate your personal computer.

The wireless mouse functions will work with personal

computers compatible with IBM PS/2, serial (RS-232C) or

Apple ADB type mouse systems.

PC CONTROL

OFF

Personal computer

S-VIDEO

VIDEO

AUDIO

110-120V/

200-240V~

To mouse terminal

Supplied

computer

control cable

Supplied mouse control cable (for IBM

PS/2, serial and Apple ADB type mouse)

Functions and Operations

VOL

MUTE

MAIN POWER switch of remote control

LEFT-CLICK button

OFF

POWER ON/OFF

buttons

BLACK

SCREEN

LASER/

LASER POINTER button

MOUSE buttons

RIGHT-CLICK button

R-CLICK/ENTER

INPUT SELECT

DATA1

DATA2

VIDEO1

CHECK

VIDEO2

MOUSE/ADJUSTMENT

switch

MOUSE

ADJ.

LIGHT

LCD PROJECTOR

• First, connect the units as shown above, and turn the projector power on.

• Second, turn the computer power on.

• Next, slide the MAIN POWER switch on the side of the remote control.

• When using the remote control as a wireless mouse, move the MOUSE/ADJUSTMENT switch to the MOUSE position.

Notes:

• In some situations the wireless mouse may be inoperable if your computer port is not correctly set-up. Please refer to your computer owners

manual for details on setting-up/installing the correct mouse driver.

• Be sure to use the computer control cable when connecting the PC CONTROL terminals.

• Do not connect or remove the mouse control cables and computer control cable to/from your computer while it is on. This may damage your

computer.

• Only one set of connection cables is supplied with your projector. For additional connection cables, contact your nearest Authorized Sharp

Industrial LCD Products Dealer or Service Center.

• Do not connect the mouse input terminal for IBM/Mac and the mouse input terminal for PC98 simultaneously.

MOUSE buttons

By lightly pressing the up/down and right/left arrow buttons located on the front of the remote

control, you can move the mouse cursor on your monitor screen.

Note:

• The amount of pressure applied to the MOUSE button determines the speed the mouse cursor travels. Pressing

lightly on the periphery of the MOUSE button makes the mouse cursor move slowly. Pressing hard makes it move

quickly.

Mouse cursor

LEFT-CLICK button

RIGHT-CLICK button

The LEFT-CLICK button on the back of the remote control corresponds to the left button

of the mouse on two-button mouse systems.

The RIGHT-CLICK button on the front of the remote control corresponds to the right

button on two-button mouse systems.

Note: For one-button mouse systems use either the LEFT-CLICK or RIGHT-CLICK button.

LASER POINTER button Press the LASER POINTER button to activate the laser pointer.

When the button is pressed, the light stays on; when the button is released, the light

goes off. However, even when the button is pressed continuously, the light automati-

cally goes off 1 minute after it goes on. To turn it on again press the laser pointer button

one more time.

The laser pointer on the remote control emits

a laser beam from the laser light window. The

laser emitted is a class II laser; therefore, do

"COMPLIES WITH 21 CFR SUBCHAPTER J"

SHARP ELECTRONICS CORPORATION

SHARP PLAZA, MAHWAH, NEW JERSEY 07430

CAUTION

U.S.A. ONLY

TEL : 1-800-BE-SHARP

LASER RADIATION-

not look into the laser window or shine the

laser beam on yourself or other people. The

two marks to the left are the caution labels for

the laser beam.

REMOTE CONTROL

MODEL NO. : G1414CESA

DC6V (1.5VX4PCS.)

MADE IN JAPAN

DO NOT STARE INTO BEAM

WAVE LENGTH : 670nm

MAX. OUTPUT : 1mW

CLASS II LASER PRODUCT FABRIQUÉ AU JAPON

Always use the laser pointer at temperatures

between 41°F and 104°F (

5°C and

40°C).

E-8

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting Up the Projector

Using the Focus and Zoom

• Zoom, Focus and Reversed/Inverted Image mode functions broaden your options for projector placement.

• See pages 10, 11 and 12 for details on projector setup.

SIDE VIEW

Zoom

Ceiling setting

Invert Image

Table setting

Zoom

1. Turn on the MAIN POWER

Turn on the MAIN POWER switch on the back of the

projector.

2. Turn on the POWER

POWER

LAMP

TEMP.

Press the POWER ON/OFF button on the projector or the

POWER ON button on the remote control to turn on the

power.

POWER indicator

3. Rotating the zoom ring (from the

housed position to the wide angle

→

position)

Rotate the zoom ring on the lens until it clicks. The pic-

ture can be adjusted within the zoom range.

Zoom ring

(Lens housed)

(Wide angle)

4. Adjusting the focus

Rotate the lens focusing ring until the image on the

screen is in focus.

Lens focusing ring

5. Adjusting the zoom

Rotate the zoom ring. The picture can be adjusted to the

desired size within the zoom range.

↔

Zoom ring

(Maximum picture size)

(Minimum picture size)

(Zoom)

E-9

Download from Www.Somanuals.com. All Manuals Search And Download.

Projector Distance and Picture Size Relationship

• The zoom lens allows adjustment of the image size within the projector’s range.

• For optimum picture adjustment, the projector should be placed and adjusted at a distance between 4.6 ft

(1.4 m) and 57.4 ft (17.5 m) from the screen.

Distance from screen

Picture size: 100 inches (254 cm)

Projection distance (L)

Picture size

(diag.)

Maximum projection distance Minimum projection distance

57.4 ft (17.5 m)

38.4 ft (11.7 m)

28.5 ft (8.7 m)

19.0 ft (5.8 m)

15.1 ft (4.6 m)

11.5 ft (3.5 m)

7.5 ft (2.3 m)

35.8 ft (10.9 m)

23.9 ft (7.3 m)

17.7 ft (5.4 m)

11.8 ft (3.6 m)

9.5 ft (2.9 m)

6.9 ft (2.1 m)

4.6 ft (1.4 m)

300 in. (240 Љ W

180 Љ H)

200 in. (160 Љ W

120 Љ H)

150 in. (120 Љ W

90 Љ H)

100 in. (80 Љ W

60 Љ H)

80 in. (64 Љ W

48 Љ H)

60 in. (48 Љ W

36 Љ H)

40 in. (32 Љ W

24 Љ H)

Zoom adjustment range: 19.0 ft–11.8 ft

The formula for picture size and projection

distance

y = (0.0586x

0.0544)

3.28

y¹= (0.0367x

0.0702)

3.28

x²: Picture size (diag.) (inches)

y : Maximum projection distance (ft)

y¹₂: Minimum projection distance (ft)

Lens

center

90˚

Note:

• There is an error of

4 inches (

10 cm) in the

formula above.

Minimum L: 11.8 ft (3.6 m)

Maximum L: 19.0 ft (5.8 m)

Distance between lens and screen: L

• Above is an illustration of maximum and minimum projection distances for the PG-D210U with a picture size of 100 inches

(254 cm). Move the projector forward or backward if the edges of the image are distorted.

Height of Projector

Adjust to match the setup configuration.

Picture size

(diag.)

Distance from lens center to

lower edge of screen (H)

300 in. (240 Љ W

180 Љ H)

200 in. (160 Љ W

120 Љ H)

150 in. (120 Љ W

90 Љ H)

100 in. (80 Љ W

60 Љ H)

80 in. (64 Љ W

48 Љ H)

60 in. (48 Љ W

36 Љ H)

40 in. (32 Љ W

24 Љ H)

26.0 in. (66 cm)

17.3 in. (44 cm)

13.0 in. (33 cm)

8.7 in. (22 cm)

7.1 in. (18 cm)

5.1 in. (13 cm)

3.5 in. (9 cm)

Screen

Lens center

90˚

Rack/stand

Lower edge of screen

(white portion) = Standard (0) point

• Ceiling Mount

When the projector is in the inverted position, use the high

edge of the screen as the base line.

High edge of screen

90˚

Note:

• Optimal image quality is produced with the projector positioned perpendicular to the screen with all feet flat and level.

E-10

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Image Invert/Reverse Function

This projector is equipped with an image invert/reverse function. The projected image can be inverted or reversed

by using the MENU button and the ADJUSTMENT ƒ/∂ and ß/© buttons.

On-Screen Display

1. Press the MENU button

I M A G E A D J .

With the MENU screen displayed, press the AD-

JUSTMENT ƒ/∂ buttons to select “IMAGE ADJ.”.

Then press the ENTER button to display the

“IMAGE ADJ.” screen.

[

]

B L K S C R N D I S P

I N P U T D I S P L A Y

R E V E R S E

O F F

I N V E R T

• The last MENU screen selected is indicated for about

30 seconds.

: S E L .

: A D J .

: E N D

2. Reversed Image Mode

I M A G E A D J .

In the “IMAGE ADJ.” menu, press the

]

[

O F F

B L K S C R N D I S P

I N P U T D I S P L A Y

R E V E R S E

ADJUSTMENT ƒ/∂ buttons to select “REVERSE”.

Then press the ADJUSTMENT ß/© buttons to

select “ON”. The reversed image will appear.

[

O F F

]

[

O N

]

[

O F F

I N V E R T

: S E L .

: A D J .

M E N U

: E N D

3. Inverted Image Mode

: E N D

M E N U

: A D J .

: S E L .

In the “IMAGE ADJ.” menu, press the

ADJUSTMENT ƒ/∂ buttons to select “INVERT”.

Then press the ADJUSTMENT ß/© buttons to

select “ON”. The inverted image will appear.

O N

I N V E R T

]

[

O F F

[

R E V E R S E

]

O F F

[

I N P U T D I S P L A Y

B L K S C R N D I S P

]

O F F

[

I M A G E A D J .

4. Reversed Inverted Image Mode

In the “IMAGE ADJ.” menu, set the “REVERSE” and

“INVERT” functions to “ON”. The reversed inverted

image will appear.

: A D J .

: S E L .

_MENU: E N D

I N V E R T

O N

[

]

R E V E R S E

[

I N P U T D I S P L A Y

B L K S C R N D I S P

O F F

]

I M A G E A D J .

5. Press the MENU button anytime to exit

“IMAGE ADJ.”

How to set up the projector and screen

Cautions:When setting up the projector

• For minimal servicing and to maintain high image quality, SHARP recommends that this projector be installed

in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environ-

ments, the lens and filter must be cleaned more often. Periodically the filter should be replaced and the pro-

jector should be cleaned internally. As long as the projector is properly maintained in this manner, use in these

environments will not reduce the overall operation life. Please note that all internal cleaning must be performed

by an Authorized Sharp Industrial LCD Products Dealer or Service Center.

• Do not expose to extreme heat or cold.

Operating temperature: 41°F to 104°F (

5°C to

40°C)

Storage temperature:

4°F to 140°F (

20°C to

60°C)

• Do not tilt the projector more than 5°.

• Position the screen so that it is not in direct sunlight or room light. Light falling directly onto the screen washes

out colors, making viewing difficult. Close the curtains and dim the lights when using the screen in a bright or

sunny room.

• The best picture will be obtained when the projector is at a 90 degree angle to the screen. Position the projector

and screen as shown.

E-11

Download from Www.Somanuals.com. All Manuals Search And Download.

Example of a standard setup

TOP VIEW

SIDE VIEW

Lens center

90˚

Lens center

The projector lens should be centered

in the middle of the screen.

If the projector and screen are not

centered properly, the picture will be

distorted, making viewing difficult.

Using the horizontal reverse function makes the following setups possible.

Example of a reversed image setup

• By placing a mirror (normal flat type) in front of the lens and using the horizontal reverse function, the image reflected from

the mirror can be projected onto the screen.

• Rear projection with a rear projection screen is also possible when using the horizontal reverse function.

Rear Projection

AUDIENCE SIDE

90˚

Mirror

The projector lens should be centered

in the middle of the screen.

If the projector and screen are not

centered properly, the picture will be

distorted, making viewing difficult.

Example of a ceiling-mount setup

Before mounting the projector, be sure to contact your nearest Authorized Sharp Industrial LCD Products Dealer to

obtain the manufacturer recommended ceiling mount bracket (sold separately). (AN-XGCM40 Ceiling Mount

Bracket, AN-EP101AP Extension Tube for AN-XGCM40).

TOP VIEW

SIDE VIEW

90˚

Lens center

• If the relative positions of the projector and the screen are not properly adjusted, the picture will be distorted.

Note:

• A polarizing screen cannot be used with this projector.

E-12

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting the Height of the Picture

Use the adjuster release to adjust the angle of the projector and height of the picture. Minor adjustments can be

made with the adjusters.

Adjuster

release

Adjuster release

Adjusters

1. Press the adjuster release and lift the

projector to the desired angle with both

hands

• The adjuster legs will extend to the surface of the

table.

2. Remove your hand from the adjuster

release

• The adjuster legs will lock in position. Release the

projector once you are sure the adjuster legs

have locked in position.

3. Make any minor adjustments necessary

• Turn the adjusters to further adjust the angle of

the projector.

Returning the projector to its original position

• While holding the projector with both hands, press the

adjuster release and slowly lower the projector to its original

position.

Notes:

• Adjustable up to approximately 5° from the horizontal.

• When adjustments are made with the adjusters, the picture may

become distorted, depending on the relative positions of the

projector and the screen.

• After adjusting, in some cases, all of the adjuster legs may not be

resting on the table.

To prevent the projector from wobbling, adjust the adjuster legs so

that they firmly contact the table.

Cautions:

• Do not press the adjuster release when the adjuster legs are

extended without firmly holding the projector.

• When lowering the projector, be careful not to get your fingers caught

in the area between the adjusters and the projector.

• Do not hold the lens when lifting or lowering the projector.

Transporting the Projector

Use the carrying handle when carrying the projector.

When transporting the projector, carry it by the handle located on the

side of the unit.

Note:

Carrying handle

• Always put on the lens cap to prevent damage to the lens when transporting

the projector.

Caution:

• Do not lift or carry the projector by the lens or the lens cap as this may

damage the lens.

E-13

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the Projector (VIDEO 1, VIDEO 2)

To playback audio and video with the projector connected to a VCR, Laser Disc Player or external audio amplifier,

make the following connections.

• Always turn off the LCD Projector while connecting to video equipment, in order to protect both the projector and the

equipment being connected.

Rear terminals

COMPUTER RGB

COMPUTER AUDIO

IN 1

IN 2

IN 1

IN 2

Used when the AV equipment

to be connected has an

AUDIO

OUTPUT

WIRED

REMOTE

OUT

S-VIDEO output terminal.

PC CONTROL

OFF

S-VIDEO

VIDEO

AUDIO

110-120V/

200-240V~

Playback

audio

output

video

output

terminal

S-video

output

audio

output

audio

input

terminals

terminal

terminals

Video equipment

VCR

Amplifier

Select the audio you want to output by selecting VIDEO 1 or VIDEO 2.

Note the following when using the S-VIDEO INPUT terminal:

• The S-VIDEO INPUT terminal uses a video signal system in which the picture is separated into a color and a luminance signal

to realize a higher-quality picture.

• By using the external amplifier, the volume can be amplified for greater sound.

E-14

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the Projector (RGB 1, 2: Computer)

• Please carefully read the manual of the computer you will be con-

necting.

• Before connecting, be sure to turn both the projector and the computer

off. After making all connections, turn the projector on first. The com-

puter should always be turned on last.

6-pin DIN

Personal computer

Mouse Control

Cable for IBM

PS/2 (Supplied)

4-pin DIN

Mouse Control

Cable for

Macintosh

Series

To display input terminal

Note:

15-pin D-Sub

• The arrows (←, ↔ ) indicate the

direction of the signals.

(Supplied)

To RS-232C

terminal

Macintosh Adaptor

(Supplied)

15-pin D-Sub

Rear terminals

RGB Signal Cable (Supplied)

RS-232C

cable (Cross

Type, sold

separately)

COMPUTER RGB

COMPUTER AUDIO

IN 1

IN 2

IN 1

IN 2

Audio Cable for Personal Computer (Supplied)

9-pin D-Sub

AUDIO

OUTPUT

WIRED

REMOTE

OUT

Mouse Control Cable (Supplied)

PC CONTROL

9-pin D-Sub

OFF

S-VIDEO

VIDEO

Computer Control Cable

(with mouse/RS-232C

input terminal) (Supplied)

Note:

AUDIO

110-120V/

200-240V~

• By using RGB INPUT 2 and PC CONTROL 2,

another computer can be connected to and

operated with the projector. The RS-232C func-

tion, however, will not operate when used with

the PC CONTROL 2 terminal.

COMPUTER CONTROL CABLE

RS-232C (D-sub 9-pin)

Use when controlling the projector from your personal computer.

(RS-232C does not function when connected to PC CONTROL 2.)

MOUSE TERMINAL

Use when operating your personal computer with the wireless mouse

remote control.

Left Terminal: D-sub 9-pin (for IBM/Mac)

Right Terminal: 9-pin mini DIN (for NEC in JAPAN)

• You can connect your projector to a computer for easy projection of full color computer images and an external monitor for

simultaneous viewing. See pages 16 and 17 for details of the connections.

• Refer to page 18 for a list of personal computers connectable to the projector. Use with computers other than those listed

may cause some of the functions not to work.

• When the RS-232C terminal on this unit is connected to a personal computer via an RS-232C cable (cross type) and the sup-

plied computer control cable, the personal computer can control the projector and the status of the projector can be

checked. See pages 34 and 35 for details.

• By connecting the supplied computer control cable to the PC CONTROL terminal on your projector and the supplied mouse

control cables to the mouse terminal on your personal computer, you can use the wireless mouse on the remote control,

instead of the mouse equipped with your personal computer, to operate your personal computer. Refer to page 8 for details.

Notes:

• The RS-232C function will only operate when the connection cable is connected to the PC CONTROL 1 terminal on the projector.

• The wireless mouse or RS-232C function may not operate if your computer port is not correctly set-up. Please refer to your computer owners

manual for details on setting-up/installing the correct mouse driver.

• Do not connect or remove the computer control cable, mouse control cables, or RS-232C cable to/from your computer while it is on. This may

damage your computer.

• Do not connect to the mouse input terminals on the computer control cable for IBM/Mac and PC98 simultaneously.

• Be sure to use the supplied computer control cable when connecting the PC CONTROL terminals.

“Plug and Play” Function

This projector is compatible with VESA DDC 1 and DDC 2B standards.

This projector and a VESA DDC compatible computer will communicate their setting requirements, allowing for quick and easy

set-up.

Note:

• The DDC, “Plug and Play” function of this projector is only functional when used in conjunction with a VESA DDC compatible computer.

E-15

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting to the Computer RGB Input (RGB 1, 2)/Output Terminals

You can connect your projector to a computer for easy projection of full-color computer images, and an external

monitor for simultaneous viewing.

1. Connecting to an IBM-PC (VGA, SVGA,

Rear view of the projector

COMPUTER RGB

XGA, SXGA) Series computer—1,280

1,024 maximum resolution

IN 1

IN 2

RGB Signal

Input Socket

Plug one end of the RGB signal cable into the RGB

INPUT terminal on the projector and the other end

into the RGB signal output terminal on the

computer, and secure the plugs by tightening the

thumb screws.

IBM-PC (VGA,

SVGA, XGA, SXGA)

Series (computer)

Notes:

ANALOG RGB OUT

RGB Signal

Cable

(Supplied)

• This connection is possible only when using a computer with a VGA/

SVGA/XGA/SXGA or Mac display output port.

• By using RGB INPUT 2 and PC CONTROL 2, another computer can

be connected to and operated with the projector.

RGB Signal

Output Socket

Macintosh Adaptor (Supplied)

2 !

2. Connecting to a Macintosh Series

Computer

640

480, 832

624 or 1,024

768 resolution

↑

! Set the proper switches on the supplied

adaptor.

↓

• For 640

480 resolution, set switches 1 and

2 to “ON” and 3, 4, 5 and 6 to “OFF”.

• For 832

624 resolution, set switches 2 and

4 to “ON” and 1, 3, 5 and 6 to “OFF”.

• For 1,024

768 resolution, set switches 2

and 3 to “ON” and 1, 4, 5 and 6 to “OFF”.

OFF

Macintosh Adaptor (Supplied)

@ Connect the supplied Macintosh adaptor to the

RGB signal output terminal on your Macintosh

Series computer, as shown on the left, and

secure the plugs by tightening the thumb

screws.

Macintosh

ANALOG RGB OUT

RGB Signal

Output Socket

# Firmly plug one end of the supplied RGB signal

cable into the RGB input terminal on the

projector and the other end to the Macintosh

adaptor on the computer, and secure the plugs

by tightening the thumb screws.

Rear view of the projector

COMPUTER RGB

IN 1

IN 2

RGB Signal

Input Socket

Notes:

Macintosh

• Be sure to use the supplied Macintosh adaptor.

• Be sure the switches on the adaptor are properly set.

• Once the adaptor is connected to a computer and the computer is

turned on, the display mode cannot be changed even if the switches

on the adaptor are reset.

RGB Signal

Output Socket

• The supplied adaptor is only for use with H-SYNC and V-SYNC out-

put. When connecting a Macintosh Series computer that only outputs

C-SYNC, use a special C-SYNC output adaptor (sold separately).

ANALOG RGB OUT

RGB Signal

Cable

(Supplied)

E-16

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Connecting to other compatible

computers

When connecting the projector to a compatible computer

other than an IBM-PC (VGA/SVGA/XGA/SXGA) or

Macintosh series, a separate cable may be needed.

Please contact your dealer for ordering information.

Notes:

• Connecting computers other than the recommended types may

result in damage to the projector, the computer, or both.

• Connect the audio from the computer to the COMPUTER AUDIO

INPUT terminal.

4. Connecting to the COMPUTER AUDIO

COMPUTER AUDIO

IN 2

IN 1

IN 2

INPUT

• The COMPUTER AUDIO INPUT 1 accepts audio from

the COMPUTER RGB 1 input, and the COMPUTER

AUDIO INPUT 2 accepts audio from the COMPUTER

RGB 2 input.

AUDIO

OUTPUT

WIRED

REMOTE

• Connect a 3.5 mm Stereo Minijack cable from the

audio output terminal on the computer to the

COMPUTER AUDIO INPUT terminal on the projector.

PC CONTROL

COMPUTER RGB

IN 1

IN 2

5. Connecting an external monitor

Connect your computer monitor to the projector’s COM-

PUTER RGB OUTPUT terminal to view images simulta-

neously on the external monitor and the projection

screen. Select either RGB 1 or RGB 2 to output the

images to the monitor.

OUT

Optional Macintosh

adaptor cable

Direct

connection

U.S.A. ONLY

Caution (Apple Macintosh):

Do not connect the COMPUTER RGB OUTPUT to any moni-

tor except the following:

Apple Color RGB Monitor 13؆/14؆ (640

480), 16؆/17؆ (832

624) or 19؆ (1,024

768)

The output signal from the projector to the monitor should be

the same as the input signal from the computer to the

projector.

External IBM-PC

monitor

External Macintosh

monitor

Examples:

Input 13؆/14؆ (640

480) → Output (640

480)

Input 16؆/17؆ (832

624) → Output (832

624)

Input 19؆ (1,024

768) → Output (1,024

768)

Note:

• The supplied adaptor is only for use with H-SYNC and V-SYNC

output. No picture will appear when connected to monitors that

only use C-SYNC.

Notes:

• When using the projector with an external IBM-PC monitor, connect

the monitor using the supplied cable. When using the projector with a

Macintosh monitor, an optional adaptor cable is required. Before

using any other type of monitor, carefully check the monitor’s inter-

face specifications and make sure that they match the specifications

of the projector’s interface.

• The external monitor output will only display an analog computer

input signal. It will not display a digital or video input signal. To split

the composite video signal, use a video distribution amplifier. This is

available from your local dealer. The computer RGB output will only

loop through the same signal connected to the computer RGB input.

(VGA IN → VGA OUT, Mac IN → Mac OUT)

E-17

Download from Www.Somanuals.com. All Manuals Search And Download.

Input Signals (Recommended Timing)

For Apple Macintosh Series

For IBM and compatibles

VIDEO SIGNAL

Input signals:

The video output signal timing of different types of

video signals are shown below for reference.

C-SYNC(H)

VIDEO SIGNAL

HORIZONTAL

SYNC SIGNAL

e = 2 dot

VIDEO SIGNAL

C-SYNC(V)

VIDEO SIGNAL

VERTICAL

SYNC SIGNAL

V-SYNC

IBM

Apple

Macintosh^TMMacintosh^TM

Apple

VGA

VESA

SVGA

Graphic

SVGA

VESA

SVGA

VESA

SVGA

VESA

XGA

SXGA

VESA

SXGA

VESA

IIsi

VESA

MODE

Text

720 dots

Graphic

640 dots

Graphic

13" Monitor 13" Monitor 16" Monitor 19" Monitor

Guideline Standard Standard Guideline Standard Standard Standard Standard

640 dots 800 dots 800 dots 800 dots 800 dots 1,024 dots 1,024 dots 1,024 dots 1,280 dots 1,280 dots 640 dots

640 dots

480 lines

832 dots

624 lines

1,024 dots

768 lines

350 lines 400 lines 350 lines 400 lines 480 lines 480 lines 600 lines 600 lines 600 lines 600 lines 768 lines 768 lines 768 lines 1,024 lines 1,024 lines 480 lines

0.7Vp-p

0.7Vp-p 1Vp-p max. 0.7Vp-p max. 0.7Vp-p max. 0.7Vp-p max.

LEVEL

TYPE

dot

75Ω load

75Ω load 75Ω load 75Ω load 75Ω load 75Ω load 75Ω load 75Ω load 75Ω load 75Ω load 75Ω load 75Ω load

75Ω load

VIDEO

R • G • B

R • G • B R • G • B R • G • B R • G • B R • G • B R • G • B R • G • B R • G • B R • G • B R • G • B

C.SYNC

R • G • B

C.SYNC

R • G • B

C.SYNC

R • G • B

C.SYNC

R • G • B

FRONT PORCH

SYNC

dot

µs

108

128

120

160

136

160

136

144

176

112

248

144

248

116

224

173

BACK PORCH

128

VIDEO PERIOD

720

640

800

1,024

1,344

20.677

15.385

48.363

65.000

TTL

1,024

1,328

17.707

13.3

1,024

1,312

16.660

12.7

1,280

1,688

15.6

1,280

1,688

12.5

640

832

1,024

1,328

16.650

12.538

60.0

900

800

832

1,024

28.444

27.777

35.156

36.000

TTL

1,056

26.400

25.000

37.879

40.000

TTL

1,040

20.800

20.000

48.077

50.000

TTL

1,056

21.333

20.202

46.875

49.500

TTL

864

896

1,152

20.124

17.468

49.693

57.246

TTL

1H (a+b+c+d)

31.7774

35.3082

31.4689

28.322

31.7776

39.7219

31.4688

25.175

TTL

26.413

31.746

37.860

31.500

TTL

28.5714

33.0688

35.0000

30.2400

TTL

28.595

31.914063

34.971149

31.334149

TTL

1 dot

1/H

9.3

7.4

kHz

MHz

56.476

75.0

60.023

78.75

TTL

63.981

108.000

TTL

79.976

135.000

TTL

1/dot

LEVEL

79.76

TTL

–

TTL

SYNC POLARITY

+/–

–

+/–

–

FRONT PORCH

SYNC

BACK PORCH

VIDEO PERIOD

350

449

400

449

350

449

400

449

480

525

480

600

768

1,024

1,066

16.7

60.020

TTL

1,024

1,066

16.7

75.025

TTL

480

525

15.00

66.67

TTL

–

480

525

15.00

66.67

TTL

–

624

768

804

13.387

74.70

TTL

–

520

625

628

666

625

806

800

667

1V (w+x+y+z)

14.2681 14.2681 14.2681 14.2681 16.6832

70.0866 70.0866 70.0863 70.0863 59.9405

13.735

72.809

TTL

–

17.778

56.250

TTL

+/–

16.579

60.317

TTL

13.853

72.188

TTL

13.333

75.000

TTL

16.666

60.006

TTL

–

14.272

70.069

TTL

–

13.328

75.029

TTL

13.423

74.502

TTL

–

1/v

LEVEL

TTL

–

TTL

–

TTL

–

SYNC POLARITY

+/–

Notes:

• When connecting a notebook computer to the data-projector for display on an (800

600) LCD screen, the screen may

not show a full picture image. See page 20, “Computer Mode Memory Adjustments” for details.

• This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. If this

occurs, turn off the LCD display on the notebook computer and output the display data in “CRT only” mode. Details on

how to change display modes can be found in your notebook computer’s operation manual.

E-18

Download from Www.Somanuals.com. All Manuals Search And Download.

RGB Adjustment Controls

When displaying computer patterns which repeat every other dot (tiling, vertical stripes, etc.), interference may

occur between the LCD pixels, causing flickering, vertical stripes, or contrast irregularities in portions of the

screen. Should this occur, use the ADJUSTMENT ß/© buttons for HORIZONTAL (LEFT/RIGHT) and VERTICAL

(UP/DOWN) position adjustments to adjust for the optimum picture.

RGB Input Adjustments (“CLOCK”, “PHASE”, “V-POS”

and “H-POS”)

1. Select the input of the image you want to adjust (RGB 1 or

2) with the INPUT SELECT button and press the MENU

button.

With the MENU screen displayed, press the ADJUSTMENT ƒ/∂ buttons

to select “RGB 1 INPUT ADJ.” Then press the ENTER button to display the

“RGB 1 INPUT ADJ.” screen.

On-Screen Display

2. Select the item you wish to adjust with the ADJUST-

MENT ƒ/∂ buttons. Adjust the item with the ADJUST-

MENT ß/© buttons.

R G B 1 I N P U T A D J .

C L O C K

P H A S E

H - P O S

V - P O S

[

]

M O D E

O F F

R E S E T

M E M O R Y S E L E C T

Note:

• To display only the item that you want to adjust, press the ENTER button after selecting the item

with the ADJUSTMENT ƒ/∂ buttons. Then adjust the item with the ADJUSTMENT ß/© buttons.

: S E L .

: A D J .

ENTER

: N E X T

: E N D

3. Press the MENU button anytime to exit RGB INPUT ADJ.

Description of Adjustment Items

CLOCK SPEED ADJUSTMENT (FAST/SLOW)

• Adjust the input signal horizontal frequency and the dot clock so that the screen

display is normal.

PHASE ADJUSTMENT (UP/DOWN)

• Used to reduce image distortion or improve contrast.

HORIZONTAL POSITION ADJUSTMENT (LEFT/RIGHT)

• Used to center the on-screen image by moving it to the left or right.

VERTICAL POSITION ADJUSTMENT (UP/DOWN)

• Used to center the on-screen image by moving it up or down.

MODE ADJUSTMENT

C^{ONNECTING TO}IBM-PC COMPUTERS

• Ordinarily, the type of input signal is detected and the correct resolution mode

(Text or Graphics) is automatically selected. However, for the following signals,

set “MODE” to “ON” or “OFF” to select the projector’s resolution mode to match

the computer display mode properly.

720 dots

400 lines, 720 dots

350 lines (Text Mode)

640 dots

400 lines, 640 dots

350 lines (Graphic Mode)

• For graphic mode, select “MODE” and set the “MODE” to “ON”.

• For text mode, select “MODE” again at this time, and set “MODE” to “OFF”.

C^{ONNECTING TO}MACINTOSH LC/II SERIES COMPUTERS

• When connecting to a Macintosh II with 35 kHz Dot Frequency, select “MODE”

and set “MODE” to “ON”.

• When connecting to a Macintosh LC Series computer with 34.97 kHz Dot Fre-

quency, set “MODE” to “OFF”.

• When connecting to third party video cards and other Macintosh computers, set

“MODE” to “ON” or “OFF” to select the correct display mode.

• When the input signal is automatically detected or when there is no input signal,

“MODE (---)” appears on the screen and the display mode cannot be changed.

INITIAL RESET

• To return the “H-POS”, “V-POS”, “PHASE” and “CLOCK” adjustments to their

initial settings, select “RESET” and then press the ENTER button.

MEMORY SELECT

• Used to store up to seven computer mode adjustments.

Note:

• Avoid displaying computer patterns which repeat every other line (horizontal stripes). (Flickering

may occur, making the picture hard to see.)

E-19

Download from Www.Somanuals.com. All Manuals Search And Download.

Computer Mode Memory Adjustments

• The projector has been preset with different modes for

use with XGA and other compatible computers.

However, 7 memory positions are provided to store

mode adjustments.

• Each memory position can be used to store mode

adjustments to match the computer.

1 When RGB 1 or 2 is selected.

1. Press the ENTER button to select the

Memory Adjustment mode

On-Screen Display

• Press the MENU button. While the MENU screen

is displayed, press the ADJUSTMENT ƒ/∂ but-

tons to select “RGB1 INPUT ADJ.” Press the

ENTER button. The MENU mode changes as

shown.

R G B 1 I N P U T A D J .

C L O C K

P H A S E

H - P O S

V - P O S

M O D E

R E S E T

M E M O R Y S E L E C T

R G B 1 A D J .

R G B 1 I N P U T A D J .

I M A G E A D J .

A U D I O

S Y S T E M S E T U P

L A N G U A G E

[

]

O F F

• While the RGB INPUT adjustment menu is dis-

played, press the ADJUSTMENT ƒ/∂ buttons to

select “MEMORY SELECT”. Then press the

ENTER button to change the image.

: S E L .

ENTER

: N E X T

: E N D

: S E L .

ENTER

: N E X T

: E N D

2. Press the ADJUSTMENT ß/© buttons

• The screen shown on the left will appear. There

are 7 memory positions.

ME MOR Y SE L E C T

• Press the ADJUSTMENT ƒ button once to move

to the following screen. Press the ADJUSTMENT

ß/© buttons to select the number of the memory

you want to adjust. If that memory position has

not been set, the screen on the right will be dis-

played. If it has been set, the screen on the left

will be displayed. MEMORY No. 0 cannot be set.

It contains the fixed factory preset settings.

• To make or change a setting, press the ADJUST-

MENT ƒ/∂ buttons to move the cursor to “SET-

TING.” Then press the ENTER button to go to the

RGB INPUT adjustment menu screen. (If you do

not want to make any adjustments, press the

MENU button.)

S T A N D A R D S E T T I N G

S E T T I N G

S T A N D A R D S E T T I N G

S E T T I N G

: S E L .

: A D J .

ENTER

: E N T E R

: E N D

: S E L .

ENTER

: B A C K

: E N D

ME MOR Y SE L E C T

N O N

R E S O L U T I O N

H O R F R E Q

V E R T F R E Q

S E T T I N G

1 0 2 4 ×7 6 8

6 0 . 0 KHz

7 5 Hz

S E T T I N G

• Select the item you want to adjust by pressing the

ADJUSTMENT ƒ/∂ buttons, then use the AD-

JUSTMENT ß/© buttons to make the adjust-

ments. When adjustments are completed, press

the MENU button. The display disappears and

the adjustments are stored in memory as a user

mode. See page 19 for details on the adjustment

items.

: S E L .

: A D J .

ENTER

: E N T E R

: S E L .

: A D J .

ENTER

: E N T E R

: E N D

3. Press the MENU button anytime to exit

RGB INPUT ADJ.

E-20

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Operation of the Projector

OFF

1. Connect the AC cord

Connect the supplied AC cord to the AC inlet on

the back of the projector.

110-120V/

200-240V~

1 AC cord

2. Turn on the MAIN POWER

POWER

LAMP

TEMP.

OFF

Press the MAIN POWER switch on the back of the

projector. The POWER indicator lights red and the

projector enters STANDBY mode.

When the MAIN

POWER is on, the

POWER indicator

lights red.

Projector

ON/OFF

Remote control

ON/OFF

3. Turn on the POWER

Press the POWER ON/OFF button on the projector or the

POWER ON button on the remote control.

• When the power is turned off by pressing the POWER

ON/OFF button, the POWER indicator will not turn off

until the fan has stopped running.

• See page 30, “Lamp/Maintenance Indicators” for

details.

OFF

Notes:

• When the POWER indicator is not lit, the remote control cannot be

used to operate the projector.

• The flashing green LAMP REPLACEMENT indicator indicates that the

lamp is warming up. Wait until the indicator stops flashing before

operating the projector.

POWER

LAMP

TEMP.

• If the power is turned on immediately after it has been turned off, it

may take a short while before the lamp turns on. (During this period

the LAMP REPLACEMENT indicator flashes.)

• After the projector is unpacked and turned on for the first time, a

slight odor may be emitted from the exhaust fan. This odor will soon

disappear with use.

When the power is on, the LAMP

REPLACEMENT indicator flashes

to show the operating condition of

the lamp.

Caution:

Green: Lamp is ready

Flashing green: Warming up

Red: Change bulb

• Be sure to take off the lens cap before operation of the projector. Do

not place the lens cap on the lens during operation. The lens cap

may become extremely hot.

E-21

Download from Www.Somanuals.com. All Manuals Search And Download.

On-Screen Display

4. Select one of eight ON-SCREEN

DISPLAY languages

L A N G U A G E

You can return to the previous screen by se-

lecting the uppermost item (turquoise) with the

ADJUSTMENT ƒ/∂ buttons (in this case, “LAN-

GUAGE”) and then pressing the ENTER button.

E N G L I S H

D E U T S C H

E S P A Ñ O L

N E D E R L A N D S

F R A N Ç A I S

I T A L I A N O

S V E N S K A

The on-screen display is set to English at the fac-

tory. The language for the unit’s ON-SCREEN DIS-

PLAY can be set to English, German, Spanish,

Dutch, French, Italian, Swedish or Japanese.

ENTER

: S E L .

: E N T E R

: E N D

Setting the ON-SCREEN DISPLAY language

1. Press the MENU button. The menu will appear on

the screen.

2. Press the ADJUSTMENT ƒ/∂ buttons to highlight

the “LANGUAGE” item yellow. Then press the

ENTER button to display the language menu.

3. Press the ADJUSTMENT ƒ/∂ buttons to highlight

the desired language yellow. Then press the ENTER

button to set the language. The ON-SCREEN DIS-

PLAY is now programmed to display in the language

chosen.

5. Change the system mode

The video input system mode is set to “AUTO” at

the factory, but it can be changed to a different

mode if the selected system mode is not

compatible with the connected audiovisual

equipment (when a color image appears in black

and white, etc.).

S Y S T E M

I M A G E A D J .

[

]

O N

A U T O

P A L

S E C A M

N T S C 4 . 4 3

N T S C 3 . 5 8

B L U E S C R E E N

B L K S C R N D I S P

I N P U T D I S P L A Y

S Y S T E M

]

O F F

[

]

R E V E R S E

O F F

➞

I N V E R T

: S E L .

ENTER

: E N T E R

: E N D

: S E L .

ENTER

: N E X T

: E N D

1. Press the MENU button. The menu will appear on

the screen.

2. Press the ADJUSTMENT ƒ/∂ buttons to highlight

the “IMAGE ADJ.” yellow. Then press the ENTER

button to display the “IMAGE ADJ.”.

3. Press the ADJUSTMENT ƒ/∂ buttons to highlight

“SYSTEM” yellow. Then press the ENTER button to

display the “SYSTEM”.

4. Press the ADJUSTMENT ƒ/∂ buttons to highlight

the desired video system yellow. Then press the

ENTER button to set the system.

Notes:

• In AUTO mode, “PAL,” “SECAM”, “NTSC 4.43” or “NTSC 3.58” is

displayed on the screen for a few seconds when the mode is

changed with the INPUT SELECT button.

• When the system mode is set to “AUTO”, you may not receive a clear

picture due to signal differences. If this happens, switch to the color

system you are viewing.

E-22

Download from Www.Somanuals.com. All Manuals Search And Download.

On-Screen Display

6. Select input

For viewing the picture from a

video source connected to:

VIDEO INPUT 1

Press the INPUT SELECT button on the projector to

switch the picture input. When you press the but-

ton, the current input mode is displayed for about 4

seconds. If you press the button again while the

input mode is displayed, the mode changes as

shown on the left.

VIDEO INPUT 2

Confirm the selected input terminal and press the

INPUT SELECT button.

COMPUTER RGB1

COMPUTER RGB2

Notes:

• The input can be selected directly using the VIDEO 1, VIDEO 2,

DATA 1 and DATA 2 buttons on the remote control. (When DATA 1 or

DATA 2 is selected, the RGB 1 or RGB 2 screen will appear

accordingly.)

• In VIDEO mode, the system being received will be indicated below

the “VIDEO” display.

• When selecting RGB mode, the resolution being displayed will be

indicated under “RGB,” as shown on the left. (Refer to the second

example when connecting to Mac display.)

• When no signals are being received, “NO SIGNAL” will be displayed.

When receiving a signal the projector is not preset to receive, “NOT

REG.” will be displayed. (This display function does not operate in

Video mode.)

Mac

• The picture size differs in RGB, NTSC, PAL and SECAM INPUT

modes.

7. Press INPUT CHECK

When the INPUT CHECK button on the remote con-

trol is pressed, the current input mode is displayed

for about 4 seconds.

Note:

• The INPUT CHECK button will not function if the “INPUT DISPLAY” is

turned off, as described on page 28.

Mac

8. Adjust the volume

Press the VOLUME UP-DOWN buttons on the pro-

jector or on the remote control to adjust the volume.

The number of displayed segments

(0–60) increases or decreases as the

volume is raised or lowered.

MUTE

• Press the MUTE button to temporarily turn off the

sound.

• Press the MUTE button once again to turn the

sound back on.

V O L U M E

3 8

9. To turn off the power from the projector

or the remote control

• Press the POWER ON/OFF button on either the

projector or the remote control. The screen on the left

will appear.

• If you want to turn off the power, press the POWER

ON/OFF button on either the projector or the remote

control again within 4 seconds. The power is now

temporarily turned off.

T U R N

P O W E R

Y E

N O

W A

• If you accidentally pressed the POWER ON/OFF button

and do not want to turn off the power, wait until the

On-Screen Display disappears.

The POWER indicator will turn red and the cooling fan

will run for 90 seconds, then the power will turn off,

and the projector will return to STANDBY mode.

POWER

LAMP

TEMP.

The power can be turned on again either from the

projector or remote control. When the power is turned

on, the POWER indicator and LAMP REPLACEMENT

indicator light green.

Note:

• When the MAIN POWER is off on the projector set, the power cannot

be turned on from the remote control.

E-23

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting the Picture

• This projector’s picture is factory preset to standard

settings. However, you can adjust it to suit your own

preferences with the ADJUSTMENT buttons on the

projector and the remote control.

• The adjustments can be memorized in RGB 1, RGB 2,

VIDEO 1 or VIDEO 2 separately.

• Four picture modes can be adjusted: “PICTURE,”

“BRIGHT,” “RED,” and “BLUE”.

Adjusting the Picture

On-Screen Display

1. Use the MENU button to select the mode

to be adjusted

R G B 1 A D J .

• When the MENU button is pressed, the MENU

mode is indicated for about 30 seconds. Press

the ADJUSTMENT ƒ/∂ buttons to select “RGB 1

ADJ.”, then press the ENTER button.

R G B 1 I N P U T A D J .

I M A G E A D J .

A U D I O

S Y S T E M S E T U P

L A N G U A G E

ENTER

: S E L .

: N E X T

: E N D

2. Adjust the Picture

R G B 1 A D J .

• Press the ADJUSTMENT ƒ/∂ buttons to high-

light yellow the picture adjustment item you want

to adjust.

P I C T U R E

B R I G H T

R E D

B L U E

R E S E T

• Press the ADJUSTMENT ß/© buttons to move

the “ ” mark of the selected adjustment item to

the desired setting.

• The adjustment mode is displayed for about

30 seconds.

ENTER

: S E L .

: A D J .

: N E X T

: E N D

Description of Adjustment Items

Selected item ADJUSTMENT ß button ADJUSTMENT © button

PICTURE

BRIGHT

RED

For less contrast

For less brightness

For weaker red

For more contrast

For more brightness

For stronger red

BLUE

COLOR

TINT

For weaker blue

For less color intensity

Skin tones become

purplish

For stronger blue

For more color intensity

Skin tones become

greenish

SHARPNESS For less sharpness

For more sharpness

All RGB Video Adjustment items are returned to the

factory preset settings.

RESET

Note: To reset all adjustment items, select “RESET” in

“RGB 1 ADJ.” mode and press the ENTER

button.

3. Display only the item to adjust

• Press the ADJUSTMENT ƒ/∂ buttons to high-

light yellow the picture adjustment item you want

to adjust. If you press the ENTER button at this

time, only the selected item will be displayed.

• Press the ADJUSTMENT ß/© buttons to move

the “ ” mark of the selected adjustment item to

the desired setting.

P I C T U R E

ENTER

: S E L .

: A D J .

: E N T E R

: E N D

• The adjustment mode is displayed for about 30

seconds.

Notes:

• When a VIDEO signal input has been selected, only “PICTURE,”

“BRIGHT,” “COLOR,” “TINT” and “SHARPNESS” can be adjusted.

• TINT only appears in NTSC 3.58 mode.

4. Press the MENU button anytime to exit

RGB ADJ.

E-24

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting the Audio

• The projector’s audio is factory preset to the standard

setting. However, you can adjust it to suit your own

preference with the ADJUSTMENT buttons on the

projector or the remote control.

• You can adjust the “BALANCE”, “TREBLE” and “BASS”.

• To return to the factory preset mode, press the AD-

JUSTMENT ƒ/∂ buttons to select “RESET”, then

press the ENTER button.

• Press the MENU button to select the normal screen

mode.

On-Screen Display

Adjusting the Audio

A U D I O

• Press the MENU button.

B A L A N C E

T R E B L E

B A S S

Select “AUDIO” with the ADJUSTMENT ƒ/∂ buttons.

Then press the ENTER button to change to the picture

indicated on the left.

R E S E T

• Select “BALANCE,” “TREBLE” or “BASS” with the AD-

JUSTMENT ƒ/∂ buttons. Adjust the mode you want

with the ADJUSTMENT ß/© buttons.

: S E L .

: A D J .

: E N D

• To return to the factory preset mode, press the AD-

JUSTMENT ƒ/∂ buttons to select “RESET”, then press

the ENTER button.

Description of Adjustment Items

Selected

items

ADJUSTMENT ß

button

ADJUSTMENT ©

button

BALANCE

Increased audio from the Increased audio from the

left speaker

Weaker treble

Weaker bass

right speaker

Stronger treble

Stronger bass

TREBLE

BASS

E-25

Download from Www.Somanuals.com. All Manuals Search And Download.

Functions on the Projector

Setting Up the System

Using this function, you can check the input signal and

lamp usage time, and select the remote mouse.

On-Screen Display

Checking the system and lamp usage time

• Press the MENU button. Select “SYSTEM SETUP” with the

ADJUSTMENT ƒ/∂ buttons. Then press the ENTER button to

change to the picture indicated on the left.

• The current system conditions, including the lamp usage

time, will be displayed on the screen.

S Y S T E M S E T U P

R E S O L U T I O N

H O R F R E Q

V E R T F R E Q

L A M P U S A G E

R E M O T E M O U S E

8 0 0 @ 6 0 0

3 7 . 9 KHz

6 0 Hz

1 2 3 4 H

[

]

A T

• Press the MENU button to select the normal screen mode.

: S E L .

Note:

: A D J .

: E N D

• In the video screen, the resolution and frequency settings will not be

displayed.

Selecting the Remote Mouse

S Y S T E M S E T U P

• Separate settings can be selected for RGB 1 and RGB 2.

• Use the INPUT SELECT buttons to select DATA 1 (RGB 1) or

DATA 2 (RGB 2).

R E S O L U T I O N

H O R F R E Q

V E R T F R E Q

L A M P U S A G E

R E M O T E M O U S E

8 0 0 @ 6 0 0

3 7 . 9 KHz

6 0 Hz

• Press the MENU button.

• Select “SYSTEM SETUP” with the ADJUSTMENT ƒ/∂

buttons. Then press the ENTER button.

1 2 3 4 H

[

]

A T

• Select “REMOTE MOUSE” and then select either “[AT]” or

• Select “[AT]” when using IBM compatibles and Apple

Macintosh series.

: S E L .

: A D J .

: E N D

• Select “[98]” when using NEC PC98 series (for Japan).

• Press the MENU button to select the normal screen mode.

Background Level

• The Background Level adjustment can be used to adjust the

picture white balance for the selected Video Input Source.

• Optimal image quality can be achieved by adjusting the

white portion of the picture to obtain the best color for the

selected source.

V I D E O 1 A D J .

B A C K G R N D L V L

I M A G E A D J .

A U D I O

S Y S T E M S E T U P

L A N G U A G E

ENTER

: S E L .

: N E X T

: E N D

Adjusting the BACKGROUND LEVEL

• Press the MENU button.

B A C K G R N D L V L

Select “BACKGRND LVL” with the ADJUSTMENT ƒ/∂ but-

tons. Then press the ENTER button to change the picture as

indicated on the left.

R E D

B L U E

R E S E T

• Select “RED” or “BLUE” with the ADJUSTMENT ƒ/∂ buttons.

tons.

• To return to the factory preset mode, press the ADJUST-

MENT ƒ/∂ buttons to select “RESET” then press the ENTER

button.

ENTER

: S E L .

: A D J .

: N E X T

: E N D

• Press the MENU button to select the normal screen mode.

Note:

• To display only the item that you want to adjust, press the ENTER

button after selecting the item with the ADJUSTMENT ƒ/∂ buttons.

E-26

Download from Www.Somanuals.com. All Manuals Search And Download.

LCD Projector

Using the Black Screen Function

This projector is equipped with a Black Screen Function.

This function can be used to black out the presentation

image.

• Press the BLACK SCREEN button on the projector or the

remote control to display the black screen. Press the BLACK

SCREEN button again to return to the presentation image.

Note:

• When “BLK SCRN DISP” is set to “OFF”, the On-Screen Display

(“BLACK SCREEN”) will not appear during black screen. See below.

BLACK SCREEN

On-Screen Display

Black Screen On-Screen Display

I M A G E A D J .

Override

[

]

O N

B L K S C R N D I S P

I N P U T D I S P L A Y

R E V E R S E

]

The On-Screen Display (“BLACK SCREEN”) that appears

during black screen can be turned off. When “BLK

SCRN DISP” is set to “OFF”, the On-Screen Display will

not appear during black screen.

O F F

I N V E R T

• Press the MENU button. While the MENU screen is displayed,

press the ADJUSTMENT ƒ/∂ buttons to select “IMAGE

ADJ.”. Then press the ENTER button to display the “IMAGE

ADJ.” screen as shown. Press the ADJUSTMENT ƒ/∂ but-

tons to select “BLK SCRN DISP” and press the ADJUST-

: S E L .

: A D J .

: E N D

E-27

Download from Www.Somanuals.com. All Manuals Search And Download.

On-Screen Display

Using the Blue Screen Function

This projector is equipped with a Blue Screen function

that will turn the screen blue when the video input termi-

nal is not connected to anything, or the video component

is turned off.

I M A G E A D J .

[

]

B L U E S C R E E N

B L K S C R N D I S P

I N P U T D I S P L A Y

S Y S T E M

O N

]

O F F

[

]

• Press the MENU button. While the MENU screen is displayed,

press the ADJUSTMENT ƒ/∂ buttons to select “IMAGE

ADJ.”. Then press the ENTER button to display the “IMAGE

ADJ.” screen as shown. Press the ADJUSTMENT ƒ/∂ but-

tons to select “BLUE SCREEN,” and press the ADJUST-

button to return to the normal screen.

R E V E R S E

O F F

I N V E R T

: S E L .

: A D J .

: E N D

• When the Blue Screen function is on, the screen will turn blue

when no video signal is being input through the video input

terminal.

• When the Blue Screen function is on, and no video signal is

input via the input terminal for more than 15 minutes, the

power is automatically turned off.

• The indicators appear as shown each minute before the

power is turned off, from 5 minutes before until 1 minute

before.

REMAIN 5M

REMAIN 4M

Notes:

• The Blue Screen function does not operate in RGB mode.

• When the power is turned off, the POWER indicator will light red.

• To turn the power on again, press the POWER button to set it to OFF,

then press it again to set it to ON.

REMAIN 1M

Using the Input Mode On-Screen Display

I M A G E A D J .

Override Function

[

]

O F F

B L K S C R N D I S P

I N P U T D I S P L A Y

R E V E R S E

The On-Screen Displays that appear during input select

(“RGB 1,024

768, 75 Hz,” etc.) can be turned off.

Once “INPUT DISPLAY” is turned off, the On-Screen Dis-

plays will not appear even if the INPUT CHECK button on

the remote control is pressed.

I N V E R T

: S E L .

: A D J .

: E N D

• Press the MENU button. While the MENU screen is displayed,

press the ADJUSTMENT ƒ/∂ buttons to select “IMAGE

ADJ.”. Then press the ENTER button to display the “IMAGE

ADJ.” screen as shown. Press the ADJUSTMENT ƒ/∂ but-

tons to select “INPUT DISPLAY,” and press ADJUST-

• When OFF is selected, the On-Screen Display (“RGB

1,024

768, 75 Hz,” etc.) will not be displayed during input

select.

E-28

Download from Www.Somanuals.com. All Manuals Search And Download.

Air Filter Maintenance

• The air filter should be cleaned every 100 hours of use. Clean the filter more

Bottom Air Filter

often when the projector is used in a dusty or smoky location.

• Have your nearest Authorized Sharp Industrial LCD Products Dealer or Ser-

vice Center exchange the filter (PFILD0080CEZZ) when it is no longer pos-

sible to clean it.

AIR FILTER cover

Cleaning and Replacing the Filter

Turn OFF

the MAIN POWER.

Remove

the FILTER COVER.

Remove

the AIR FILTER.

Press the tab in the direction of

the arrow and lift open the filter

cover.

Grasp the air filter between your

fingers and lift it out of the filter

cover.

OFF

POWER indicator goes off.

Unplug the power cord.

Tab

Press

Open

Replace

the FILTER COVER.

Clean the AIR FILTER.

Replace the AIR FILTER.

Clean the dust off the air filter

and cover with a vacuum

cleaner extension hose.

Place the filter underneath the

tabs on the filter frame.

Return the air filter to its original

position in the filter cover

opening.

Insert the tab on the end of the

filter cover into the filter cover

opening and press the filter

cover into position.

Note:

• Be sure the AIR FILTER COVER is securely installed. The power cannot be turned on unless it is correctly installed.

E-29

Download from Www.Somanuals.com. All Manuals Search And Download.

Lamp/Maintenance Indicators

Lamp

The lamp operating life differs, depending on the usage environment. It is recommended that the lamp be

replaced after 4,000 cumulative hours of use.

• When the lamp is nearing the end of its operating life, the picture and color quality will deteriorate. At this point, replace the

lamp. (See pages 31 and 32.)

Note: The lamp usage time can be checked with the On-Screen display. (See page 26.)

• If the new lamp does not light after replacement, take your projector to the nearest Authorized Sharp Industrial LCD Products

Dealer or Service Center for repair.

• Intense light hazard. Do not attempt to look into the aperture and lens while the projector is operating.

• The warning lights on the projector indicate problems inside the

projector.

Maintenance Indicators

• There are two warning lights: a TEMPERATURE indicator which warns

POWER

LAMP

TEMP.

that the projector is too hot, and a LAMP REPLACEMENT indicator which

lets you know when to change the lamp.

• If a problem occurs, either the TEMPERATURE indicator or the LAMP

REPLACEMENT indicator will light up red, and the power will shut off.

After turning off the power, follow the procedures given below.

LAMP REPLACEMENT TEMPERATURE

indicator indicator

Warning Indicator

Symptom

Problem

• Blocked air intake.

• Clogged air filter.

Possible Solution

• Relocate projector to a proper location.

TEMPERATURE

indicator

The internal

temperature is

abnormally high.

• Clean the filter.

(See page 29.)

• Cooling fan breakdown.

• Internal circuit failure.

• Take the projector to your nearest Autho-

rized Sharp Industrial LCD Products Dealer

or Service Center for repair.

• Burnt-out lamp.

• Carefully replace the lamp.

The lamp does not

light up.

LAMP REPLACE-

MENT indicator

• Take the projector to your nearest Autho-

rized Sharp Industrial LCD Products Dealer

or Service Center for repair.

• Lamp circuit failure.

Notes:

• If the TEMPERATURE indicator comes on, follow the above possible solutions and then wait until the projector has cooled down completely

before turning the power back on. (At least 5 minutes.)

• When the power is turned off and then turned on again, as during a brief rest, the LAMP REPLACEMENT indicator may be triggered, pre-

venting the power from going on. When this happens, take the power plug out of the AC outlet and put it back in again.

Before Calling for Service

Problem

Check

No picture and no sound.

• The projector AC cord is not plugged into the AC wall outlet.

• The main power switch is not pressed.

• The input is wrong. (See pages 22 and 23.)

• Cables improperly connected to rear panel of the projector. (See pages 14, 15, 16 and 17.)

• Remote control batteries have run down. (See page 7.)

• The optional cable for the remote control is improperly inserted.

• The main power of the remote control is not turned on.

• The remote control’s MOUSE/ADJUSTMENT switch is set to MOUSE.

Sound is heard but no picture

appears.

• Cables improperly connected to rear panel of the projector. (See pages 14, 15, 16 and 17.)

• The PICTURE and BRIGHT adjustments are set to minimum position. (See page 24.)

• On-Screen Display (“BLACK SCREEN”) is turned off and Black Screen function is turned on, creating a

black image. (See page 27.)

Color is faded or poor.

Picture is blurred.

• The COLOR and TINT adjustments are not correct. (See page 24.)

• Adjust the focus. (See page 9.)

• The projection distance is too long or too short to allow for proper focus. (See page 10.)

Picture appears but no sound is

heard.

• Cables improperly connected to rear panel of the projector. (See pages 14, 15, 16 and 17.)

• Volume is set to minimum. (See page 23.)

An unusual sound is occasionally • If the picture is normal, the sound is due to cabinet shrinkage caused by temperature changes. This

heard from the cabinet.

will not affect operation or performance.

Maintenance indicator lights up.

• Refer to “Lamp/Maintenance Indicators” on page 30.

E-30

Download from Www.Somanuals.com. All Manuals Search And Download.

Lamp Replacement

The lamp in the projector has a finite service life. The lamp operating life differs, depending on the usage

environment. It is recommended that the lamp be replaced after 4,000 cumulative hours of use. The lamp usage

time can be checked at the On-Screen display. (See page 26.)

• Replace the lamp when the picture starts becoming dark and the color contrast deteriorates.

Purchase a replacement UHP lamp unit (lamp/cage module) of the current type BQC-XGNV2U//1 from your

nearest Authorized Sharp Industrial LCD Products Dealer. Then change the lamp by carefully following the

instructions below.

If you wish, you may bring the projector to your nearest Authorized Sharp Industrial LCD Products Dealer.

IMPORTANT NOTE TO U.S. CUSTOMERS:

The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this

projector under warranty, including lamp replacement, must be obtained through an Authorized Sharp Industrial

LCD Products Dealer or Service Center. For the name of the nearest Authorized Sharp Industrial LCD Products

Dealer or Service Center, please call toll-free: 1-800-BE-SHARP (1-800-237-4277).

U.S.A. ONLY

How to Change the Lamp

(d)

Precaution:

(c)

(g)

(h)

(e)

• Take care not to touch either the glass surface of the lamp

cage or the inside of the projector with your bare hands.

(f)

(k)

(a)

(i)

(j)

(b)

Removing the lamp unit (see figure)

1. Press the power button (a) and turn the instrument off. After the cooling fan stops, turn off the MAIN POWER

switch (b). Remove the power cord from the AC outlet.

2. The lamp may be extremely hot. Wait at least an hour after the power cord is disconnected before carrying

out the following procedures.

3. Turn over the projector and unfasten the user service screw (d) that secures the lamp cage cover (c) as

shown in the above diagram. Then remove the lamp cage cover by pulling it in the direction of the arrow.

Note:

• When the lamp cage cover (c) has been removed, check that the surface of the lamp cage (i) has fully cooled before pro-

ceeding with step 4.

4. After the lamp cage (i) has sufficiently cooled, remove securing screws (e), (f) and (g) from the lamp cage.

5. Hold the lamp cage (i) by the handle (h) and pull it towards you.

E-31

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing the lamp unit

1. Hold the lamp cage (i) by the handle (h) and press it in firmly while making sure that grooves on the side of

the lamp cage (j) are properly aligned with the projections inside the lamp cage compartment, and that the

holes on the top of the lamp cage (k) are aligned with the screw holes on the projector.

2. Tighten screws (e), (f), (g) and (d), then perform the above instructions in the reverse order.

Caution:

• Because some parts may not be sufficiently cooled, be sure to remove the lamp cage by the handle while taking care not

to touch the metallic areas.

Resetting the lamp timer

OFF

1. Plug in the power cord.

110-120V/

200-240V~

MENT ƒ, and ENTER buttons on the projector, turn

on the MAIN POWER switch.

OFF

After the projector turns on, “LAMP 0000H” is displayed,

indicating that the lamp timer is reset.

LAMP

0000

Note:

• Only reset the lamp timer after replacing the lamp.

E-32

Download from Www.Somanuals.com. All Manuals Search And Download.

Connection Pin Assignments

Analog RGB 1 and 2 Signal Input and Analog RGB Output Terminal: 15-pin mini

D-sub female connector

Computer Input

Analog

1. Video input (red)

2. Video input (green/sync on

green)

8. Earth (blue)

9. Not connected

10. GND

3. Video input (blue)

4. Reserve input 1

5. Composite sync

6. Earth (red)

11. GND

12. Bi-directional data

13. Horizontal sync signal

14. Vertical sync signal

7. Earth (green/sync on green) 15. Data clock

Mouse Input Terminal (for IBM/Mac): 9-pin D-sub female connector

Pin No.

Signal

Name

I/O

Input

Output

Reference

Carrier Detect

Receive Data

Send Data

Equipment Ready

Signal Ground

Data Set Ready

Request to Send

Clear to Send

Ring Indicator

Connected to internal circuit

Not connected

Connected to internal circuit

Output

Input

Mouse Input Terminal (for NEC PC98 series for Japan): 9-pin mini DIN connector

Pin No.

Signal

LEFT

RIGHT

GND

I/O

Reference

Input

Computer output

Not connected

Computer output

RS-232C terminal: 9-pin D-sub male connector

Pin No.

Signal

Name

I/O

Reference

Not connected

Connected to internal circuit

Not connected

Connected to internal circuit

Not connected

Connected to internal circuit

Not connected

Receive Data

Send Data

Input

Output

Signal Ground

Data Set Ready

Request to Send

Output

E-33

Download from Www.Somanuals.com. All Manuals Search And Download.

RS-232C Terminal Specifications

1. PC control

A personal computer can be used to control the projector by connecting the supplied computer control

cable to the PC CONTROL 1 terminal on the projector and an RS-232C cable (cross type) (not supplied) to

the computer, and then connecting the RS-232C cable to the computer control cable.

(RS-232C does not function when connected to PC CONTROL 2. See page 15 for connection.)

2. Communication conditions

Set the serial port settings of the computer to match that of the table below.

Signal format:

Baud rate:

Data length:

Parity bit:

Conforms to RS-232C standard.

9,600 bps

8 bits

NON

1 bit

Stop bit:

Flow control:

None

3. Basic format

Commands from the computer are sent in the following order: command, parameter, and return code. After

the unit processes the command from the computer, it sends a response code to the computer.

Command format

C1 C2 C3 C4 P1 P2 P3 P4

Return code (0DH)

Command 4-digits Parameter 4-digits

Response code format

Normal response

Return code (0DH)

Problem response (communication error or incorrect command)

Return code (0DH)

When more than one code is being sent, send each command only after the OK response code for the

previous command from the unit is verified.

Note:

• Using the computer control function of the unit, the liquid crystal projector conditions cannot be read to the computer. There-

fore, confirm the conditions by transmitting the display commands for each adjustment menu and checking the conditions

with the On-Screen Display. If the unit receives a command other than a menu display command, it will execute the command

without displaying the On-Screen Display.

COMMAND

PARAMETER

CONTROL ITEM

CONTROL CONTENTS

POWER OFF

4. Commands

C1 C2 C3 C4 P1 P2 P3 P4

POWER SETTING

POWER ON

VIDEO 1

VIDEO 2

INPUT SWITCHING

INPUT CHECK

RGB 1

Note:

RGB 2

• If a dash appears in the parameter

column, enter a space. If an asterisk

appears, enter a value in the range

indicated in brackets under CON-

TROL CONTENTS. See the example

on the next page.

INPUT CHECK

ENGLISH

DEUTSCH

ESPANOL

NEDERLANDS

FRANCAIS

LANGUAGE

SELECTION

ITALIANO

SVENSKA

JAPANESE

AUTO

PAL

VIDEO

SYSTEM

SELECTION

SECAM

NTSC 4.43

NTSC 3.58

PICTURE (

30 –

30)

BRIGHT (

30 –

30)

COLOR (

30 –

30)

TINT (

30 –

30)

SHARPNESS (

30 –

30)

VIDEO 1 DISPLAY

RESET

VIDEO 1

IMAGE

ADJUSTMENT

PICTURE (

30 –

30)

BRIGHT (

30 –

30)

COLOR (

30 –

30)

TINT (

30 –

30)

SHARPNESS (

30 –

30)

VIDEO 2 DISPLAY

RESET

VIDEO 2

IMAGE

ADJUSTMENT

RED (

30 –

30)

BLUE (

30 –

30)

RESET

VIDEO

BACKGROUND

LEVEL

E-34

Download from Www.Somanuals.com. All Manuals Search And Download.

COMMAND

PARAMETER

CONTROL ITEM

CONTROL CONTENTS

VOLUME (0 – 60)

C1 C2 C3 C4 P1 P2 P3 P4

VOLUME

ADJUSTMENT

MUTE OFF

MUTE ON

BALANCE (

30 –

30)

TREBLE (

30 –

30)

BASS (

30 –

30)

AUDIO DISPLAY

RESET

AUDIO

ADJUSTMENT

PICTURE (

30 –

30)

BRIGHT (

30 –

30)

RED (

30 –

30)

BLUE (

30 –

30)

RGB DISPLAY

RGB 1 ADJUSTMENT

RESET

PICTURE (

30 –

30)

BRIGHT (

30 –

30)

RED (

30 –

30)

BLUE (

30 –

30)

RGB DISPLAY

RGB 2 ADJUSTMENT

RESET

CLOCK (

60 –

60)

PHASE (

60 –

60)

H-POS (

60 –

60)

V-POS (

30 –

30)

RGB INPUT DISPLAY

RESET

RGB INPUT

ADJUSTMENT

BLUE SCREEN OFF

BLUE SCREEN ON

BLACK SCREEN OFF

BLACK SCREEN ON

INPUT DISPLAY OFF

INPUT DISPLAY ON

REVERSE OFF

SCREEN SETTING

REVERSE ON

INVERT OFF

INVERT ON

VIDEO

CONFIRMATION

DISPLAY

BLACK SCREEN DISPLAY OFF

ON-SCREEN

DISPLAY SETTING

BLACK SCREEN DISPLAY ON

REMOTE MOUSE AT

MOUSE

ADJUSTMENT

REMOTE MOUSE 98

MEMORY RELEASE

SCREEN MODE

MEMORY

MEMORY SELECTION (1 – 7)

Note:

• RGB INPUT ADJUSTMENT can only be set in the displayed computer mode.

Example:

When BRIGHT of RGB 1 IMAGE ADJUSTMENT is set to

10.

Computer

Unit

→

←

E-35

Download from Www.Somanuals.com. All Manuals Search And Download.

Wired Remote Control Terminal Specifications

1. Specifications of wired remote control input

• 3.5ø minijack

• External:

5 V (1 A)

• Internal: GND

2. Function and transmission codes

No.

Control Item

System Code

Data Code

External Code

Note:

C1 C2 C3 C4 C5

C6 C7 C8 C9 C10

(Function)

C11 C12 C13 C14 C15

• To operate the MOUSE, L-CLICK and R-CLICK functions

through the wired remote control input, connect the cable

from the wired remote control (supplied) terminal on the pro-

jector to the remote control. The codes for these functions are

complex and are, therefore, not listed here.

VOLUME UP

VOLUME DOWN

POWER ON

POWER OFF

CURSOR UP

CURSOR DOWN

ADJUST UP

ADJUST DOWN

MUTE

Wired remote control function code

LSB

MSB

10 MENU

System Code

Data Code

C13 C14 C15

11 VIDEO 1

12 VIDEO 2

13 RGB1

14 RGB 2

• System codes C1 to C5 are fixed at “10110”.

• Codes C14 and C15 are reverse confirmation bits, with “10”

indicating “Front” and “01” indicating “Rear”.

15 ENTER

16 INPUT CHECK

17 BLACK SCREEN

3. Sharp remote control signal format

1. Transmission format

a. 15-bit format

67.5 ms

2. Wave form of output signal

• Output using Pulse Position Modulation

26.4 µs

“1”

“0”

“1”

“0”

• t

264 µs

• To

1.05 ms

• T1

2.10 ms

• Pulse carrier frequency

455/12 kHz

• Duty ratio

1:1

3. Transmission control code

a. 15 bit

b. Example of Reverse D to

C10 C11 C12 C13 C14 C15

Data

Expansion

Data

Deter-

System Address

Function Key Data Bit

Mask

mination

C10 C11 C12 C13 C14 C15

D to D Common Data Bit

Reverse in D

E-36

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

Product Type

LCD Projector

PG-D210U

Model

Video system

Display method

LCD panel

PAL/SECAM/NTSC 3.58/NTSC 4.43

LCD panel

3, RGB optical shutter method

Panel size: 1.3 ؆ (20.0 [H]

26.6 [W] mm)

Display method: Translucent TN liquid crystal panel

Drive method: TFT (Thin Film Transistor) Active Matrix panel

No. of dots: 786,432 dots (1,024 [H]

768 [V])

1–1.6 zoom lens, F2.5 to 3.6, f

47 to 76 mm

120 W UHP lamp

Lens

Projection lamp

Contrast ratio

200:1

Video input signal

RCA Connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 Ω terminated

RCA Connector: AUDIO, 0.5 Vrms more than 22 kΩ (stereo)

4-pin mini DIN connector

S-video input signal

Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated

C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated

520 TV lines (video input), 700 TV lines (S-video input)

2 W

2 W (stereo)

Horizontal resolution

Audio output

Computer RGB input signal

Video signal

15-PIN MINI D-SUB CONNECTOR (RGB 1, 2):

RGB separate/composite sync/sync on green type analog input:

0–0.7 Vp-p, positive, 75 Ω terminated

S^TEREOMINIJACK:

AUDIO, 0.5 Vrms, more than 22 kΩ (stereo)

H^{ORIZONTAL SYNC}. SIGNAL:

TTL level (positive/negative) or composite sync

V^{ERTICAL SYNC}. SIGNAL:

Same as above

Computer Control Cable (Supplied)

RS-232C input terminal

Mouse input terminal (for IBM/Mac)

Mouse input terminal (for PC98)

9-pin D-sub male connector for controlling personal computer

9-pin D-sub female connector for wireless mouse

9-pin mini DIN connector for wireless mouse

Speaker system

Rated voltage

2.8Љ

1.6Љ (7

4 cm) oval

AC 110–120/200–240 V

Input current

Rated frequency

1.8 A/1.0 A

50/60 Hz

Power consumption

Operating temperature

Storage temperature

Cabinet

226 W

41°F to 104°F (

5°C to

40°C)

4°F to 140°F (

20°C to

60°C)

Plastic

I/R Carrier frequency

Laser Pointer of Remote Control

40 kHz

Wave length

670 nm

Max. output

1 mW

Class II Laser Product

Dimensions (W

10.3؆

13.0؆

5.4؆ (261

329

137 mm) (main body only)

10.5؆

15.7؆

6.1؆ (266

399

155 mm) (including lens, adjuster legs and

projecting parts)

Weight

Supplied accessories

14.6 lbs. (6.6 kg)

Remote control unit, Four AA batteries, Extra air filter, RGB signal cable

(9.8Ј, 3 m), Macintosh adaptor, Computer control cable (3.3Ј, 1 m), Mouse control

cable for IBM PS/2 (5.9 Љ, 15 cm), Mouse control cable for Mac (5.9؆, 15 cm),

Mouse control cable (9.8Ј, 3 m), Computer audio cable, AC cord, Lens cap

(installed)

Replacement parts

Lamp unit (Lamp/cage module) (BQC-XGNV2U//1), Remote control

(RRMCG1414CESA), Air filter (PFILD0080CEZZ), RGB signal cable

(QCNW-5050CEZZ), Macintosh adaptor (QPLGJ1512CEZZ), Computer control

cable (CTANZ0711CE01), Mouse control cable for IBM PS/2 (QCNW-4754CEZZ),

Mouse control cable for Mac (QCNW-4755CEZZ), Mouse control cable

(QCNW-4620CEZZ), Computer audio cable (QCNW-4870CEZZ), AC cord

(QACCU5013CEZZ)

Our projector uses LCD (Liquid Crystal Display) panels. These very

sophisticated panels contain 786,432 pixels (

RGB) TFTs (Thin Film

Transistors).

As with any high technology electronic equipment such as large

screen TVs, video systems and/or video cameras, there are certain

acceptable tolerances that the equipment must conform to. This unit

has some inactive TRTs within acceptable tolerances which may result

in illuminated or inactive dots on the picture screen.

This will not affect the picture quality or the life expectancy of the unit.

If you have any questions about this matter, please call toll free 1-800-

BE-SHARP (1-800-237-4277). U.S.A. ONLY

Specifications are subject to change without notice.

E-37

Download from Www.Somanuals.com. All Manuals Search And Download.

Dimensions

Rear View

Top View

(Lens housed)

(Lens extended)

10.3 (261) 0.2 (5)

Side View

1.1 (29)

Front View

8.0 (204)

Bottom View

[Units: inches (mm)]

E-38

Download from Www.Somanuals.com. All Manuals Search And Download.

SHARP CORPORATION

OSAKA, JAPAN

Printed in Japan

Imprimé au Japon

Impreso en Japón

TINS-6785CEZZ

T2184-A

9P06-JWG

Download from Www.Somanuals.com. All Manuals Search And Download.

Sennheiser Microphone E825S User Manual
Silvercrest Photo Scanner KH2610 08 2009 V3 User Manual
Singer Sewing Machine 114W110 User Manual
Sony Home Theater System DAV DZ260 User Manual
Sony TV Mount MB 502B User Manual
Stanton CD Player C303 User Manual
Sterling Plumbing Outdoor Shower 62044106 User Manual
Sterling Plumbing Outdoor Shower 71140112 User Manual
Sunbeam Electric Steamer FOOD STEAMER User Manual
Sylvania CRT Television SRT2232X User Manual